Modern Forms WS-21712 217- Vanities and Wall Sconce Manual de usuario

Modern Forms
Marca
Modern Forms
Modelo
WS-21712 217- Vanities and Wall Sconce
Tipo
Manual de usuario
1
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
INSTALLATION INSTRUCTION
217- Vanities & Wall Sconce
WS-21712
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements
locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et
ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire.
MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación ETL/CETL esta lámpara.
PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
Wire Connector
Qty: 5pcs+1Extra
7EAC112201
P3
A
Junction Box Screw
Qty: 2pcs+1 extra
7MPF0415C2
#8-32x5/8 SS
C
Mounting Ring
Qty:1
7MBC101501
D
Conversion Plate
Qty: 1
4MBC121112CH
4MBC121112BN1
Assembly Screw
Qty:2pcs+1 extra
7MPF0808C1
#8-32x3/8 SS
Driver
Qty: 1
4LD-700MA16U-IS-P
E F G
Mounting Screw
Qty:1 extra
7MPF0409S3
5/32”-32x3/8
Nickel Plating
B
G0
2
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
INSTALLATION INSTRUCTION
217- Vanities & Wall Sconce
WS-21712
Fig.1 Mount on Switch Box
Fig.2 Mount on Junction Box
Fig.4
Fixture
Mounting
Screw
Mounting Plate
Driver 2 7/8”L X 1 3/8”W X 1/8”H
Wire Connector
Switch Box
Ground Wire
Junction Box Screw
Assembly
Screw
Mounting Plate
Conversion
Plate
Junction Box
Screw
Mounting Ring
Driver 2 7/8”L X 1 3/8”W X 1 1/8”H
Junction Box
Adjust Nut
B
G
A
C
F
E
C
D
G
Conversion Plate
1 3/8”1 5/8”
4 1/2”
5”
G0
Fixture
Backplate
Mounting
Screw
Wire
Adjust
Nut
B
3CCT Switch
3
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
INSTALLATION INSTRUCTION
217- Vanities & Wall Sconce
WS-21712
PREPARATION
1.
2.
INSTALLATION
MOUNT ON 2”X4”SWITCH BOX (Fig. 1)
3.
4.
* Required Driver to be recessed within the junction box.
6. Secure the mounting plate to the switch box using the junction box screw (C). The side of the mounting plate marked “GND” must face out.
7.
to your desired location. Third, pull and tighten the electrical wire. Lastly, secure the back plate by turning both adjust nuts clockwise.
8.
OR
MOUNT ON 4”X4”JUNCTION BOX (Fig. 2)
3.
* Required Driver to be recessed within the junction box.
6. Secure the mounting ring to the switch box using the junction box screw
(C). Make sure the two holes (Spacing 2-3/4”) are horizontal as shown in
Fig. 2. The side of the mounting plate marked “GND” must face out.
7. Secure the mounting plate and conversion plate (E) to the mounting ring
with assembly screw (F)
8.
adjust nuts by turning counterclockwise. Second adjust the back plate to
your desired location. Third, pull and tighten the electrical wire. Lastly,
secure the back plate by turning both adjust nuts clockwise.
9.
screw (B).
Back Plate Dimensions
4 1/4”
1 3/8”1 5/8”
2 3/8”
dka
1 3/8”
1 3/4”
Ф4”
Mounting Ring Dimensions
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
G0
The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch
on the mounting plate. (Fig.3).
5. Connect the driver (G) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured. if your outlet
box has a green or bare cooper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly
to the back plate using the screw provided. After wires are connected, tuck them carefully inside the switch box.
4.
The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch
on the mounting plate. (Fig.3).
5. Connect the driver (G) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured. if your outlet
box has a green or bare cooper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly
to the back plate using the screw provided. After wires are connected, tuck them carefully inside the switch box.
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
217 - LED Wall Sconce
WS-21718
Wire Connector
Qty: 5 pcs + 1 Extra
7EAC112201
P3
Mounting Screw
Qty: 1 Extra
7MPF0409S3
5/32 - 32x3/8
Nickel Plating
Junction Box Screw
Qty: 2 pcs + 1 Extra
7MPF0415C2
#8 - 32x5/8 SS
Mounting Ring
Qty: 1 pc
7MBC101501
Conversion Plate
Qty: 1 pc
4MBC151110CH
4MBC151110BN1
Assembly Screw
Qty: 2 pcs + 1 Extra
7MPF0808C1
#8 - 32x3/8 SS
Driver
Qty: 1 pc
4LD-700MA28U-IS-P
A1 B1 C1 D1 E1 F1 G1
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
217 - LED Wall Sconce
WS-21718
FIG. 1 MOUNT ON SWITCH BOX
FIG. 2 MOUNT ON JUNCTION BOX
FIG. 3
Ø
4"
Mounting Screw
Driver
Wire
Connector
Back Plate Dimensions
Mounting Plate Dimensions
Assembly Screw
Assembly Screw
Junction Box Screw
Mounting Ring
Driver
Junction
Box
Mounting Plate
Switch
Box
Ground
Wire
Mounting Plate
Fixture
Junction Box Screw
Adjustable Nut
C1
B1
G1
A1
F1
E1
C1
D1
G1
GND
5 1/2"
1 3/8"
1 3/4"
1 3/8" 1 5/8"
2 3/8"
Fixture
Backplate
Mounting
Screw
Wire
Adjust
Nut
B1
3CCT Switch
3Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1.
2.
INSTALLATION
MOUNT ON SWITCH BOX (Fig. 1)
3.
*Requires Driver to be recessed within the switch box.
6. Secure the mounting plate to the switch box using the junction box screws (C1). The side of the mounting plate marked
"GND" must face out.
7.
First, loosen both adjustable nuts by turning counterclockwise.
Second, adjust the back plate to your desired location.
Third, pull and tighten the electrical wire.
Lastly, secure the back plate by turning both adjustable nuts clockwise.
8.
OR
MOUNT ON JUNCTION BOX (Fig. 2)
3.
*Requires Driver to be recessed within the junction box.
6. Secure the mounting ring (D1) to the switch box using the junction box screws (C1). Make sure the two holes (Spacing 2-3/4") are horizontal
as shown in Fig. 2. The side of the mounting plate marked "GND" must face out.
7. Secure the mounting plate and conversion plate (E1) to the mounting ring with assembly screw (F1).
8.
First, loosen both adjustable nuts by turning counterclockwise.
Second, adjust the back plate to your desired location.
Third, pull and tighten the electrical wire.
Lastly, secure the back plate by turning both adjustable nuts clockwise.
9.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 4 Wiring
INSTALLATION INSTRUCTION
217 - LED Wall Sconce
WS-21718
4.
The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch
on the mounting plate. (Fig.3).
5. Connect the driver (G) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured. if your outlet
box has a green or bare cooper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly
to the back plate using the screw provided. After wires are connected, tuck them carefully inside the switch box.
4.
The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch
on the mounting plate. (Fig.3).
5. Connect the driver (G) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured. if your outlet
box has a green or bare cooper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly
to the back plate using the screw provided. After wires are connected, tuck them carefully inside the switch box.
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
217 - LED Wall Sconce
WS-21724 / WS-21736
Wire Connector
Qty: 5 pcs + 1 Extra
7EAC112201
P3
Mounting Screw
Qty: 1 Extra
7MPF0409S3
5/32 - 32x3/8
Nickel Plating
Junction Box Screw
Qty: 2 pcs + 1 Extra
7MPF0415C2
#8 - 32x5/8 SS
Mounting Ring
Qty: 1 pc
7MBC101501
Conversion Plate
Qty: 1 pc
4MBC171111CH
4MBC171111BN1
4MBC201105CH
4MBC201105BN1
Assembly Screw
Qty: 2 pcs + 1 Extra
7MPF0808C1
#8 - 32x3/8 SS
Driver
Qty: 1 pc
4LD-700MA28U-IS-P
A1 B1 C1 D1 E1 F1 G1
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
217 - LED Wall Sconce
WS-21724 / WS-21736
FIG. 1 MOUNT ON SWITCH BOX
FIG. 2 MOUNT ON JUNCTION BOX
FIG. 3
Ø
4
Mounting Screw
Driver
Wire Connector
Assembly Screw Conversion Plate
Junction Box Screw
Mounting Ring
Driver
Junction Box
Mounting Plate
Switch Box
Ground Wire
Back Plate Dimensions
Mounting Plate Dimensions
Fixture
Mounting Plate
Junctinon Box Screw
Adjustable Nut
C1
B1
G1
A1
F1 E1
C1
D1
G1
GND
5 7/8"
2 1/2"
1 3/8"
1 5/8"
1 3/8"
1 3/4"
FIG. 3 Mounting Screw
Fixture Back Plate
Adjustable Nut
Wire
B1
3CCT Switch
3Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
217 - LED Wall Sconce
WS-21724 / WS-21736
PREPARATION
1.
2.
INSTALLATION
MOUNT ON SWITCH BOX (Fig. 1)
3.
*Requires Driver to be recessed within the switch box.
6. Secure the mounting plate to the switch box using the junction box screws (C1). The side of the mounting plate marked
"GND" must face out.
7.
First, loosen both adjustable nuts by turning counterclockwise.
Second, adjust the back plate to your desired location.
Third, pull and tighten the electrical wire.
Lastly, secure the back plate by turning both adjustable nuts clockwise.
8.
OR
MOUNT ON JUNCTION BOX (Fig. 2)
3.
*Requires Driver to be recessed within the junction box.
6. Secure the mounting ring (D1) to the switch box using the junction box screws (C1). Make sure the two holes (Spacing 2-3/4") are horizontal
as shown in Fig. 2. The side of the mounting plate marked "GND" must face out.
7. Secure the mounting plate and conversion plate (E1) to the mounting ring with assembly screw (F1).
8.
First, loosen both adjustable nuts by turning counterclockwise.
Second, adjust the back plate to your desired location.
Third, pull and tighten the electrical wire.
Lastly, secure the back plate by turning both adjustable nuts clockwise.
9.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 4 Wiring
4.
The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch
on the mounting plate. (Fig.3).
5. Connect the driver (G) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured. if your outlet
box has a green or bare cooper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly
to the back plate using the screw provided. After wires are connected, tuck them carefully inside the switch box.
4.
The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch
on the mounting plate. (Fig.3).
5. Connect the driver (G) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured. if your outlet
box has a green or bare cooper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly
to the back plate using the screw provided. After wires are connected, tuck them carefully inside the switch box.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Modern Forms WS-21712 217- Vanities and Wall Sconce Manual de usuario

Modern Forms
Marca
Modern Forms
Modelo
WS-21712 217- Vanities and Wall Sconce
Tipo
Manual de usuario
Descargar PDF
informe

En otros idiomas

Documentos relacionados

Otros documentos