Yamaha CLP-725 El manual del propietario

Categoría
Equipo de música suplementario
Tipo
El manual del propietario
FR
EN
Owner’s Manual
Mode d’emploi
CLP
-
725
EnglishFrançais
Before using the instrument, be sure to read “PRECAUTIONS” on pages 5-6.
For information on assembling the instrument, refer to the instructions on page 31.
Avant d’utiliser l’instrument, lisez attentivement la section « PRÉCAUTIONS D’USAGE »
aux pages 5 et 6.
Pour plus d’informations sur l’assemblage de l’instrument, reportez-vous aux instructions
figurant en page 31.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instruc-
tions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may
void your authority, granted by the FCC, to use the prod-
uct.
2. IMPORTANT: When connecting this product to accesso-
ries and/or another product use only high quality shielded
cables. Cable/s supplied with this product MUST be used.
Follow all installation instructions. Failure to follow instruc-
tions could void your FCC authorization to use this prod-
uct in the USA.
3. NOTE: This product has been tested and found to com-
ply with the requirements listed in FCC Regulations, Part
15 for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance
that your use of this product in a residential environment
will not result in harmful interference with other electronic
devices. This equipment generates/uses radio frequen-
cies and, if not installed and used according to the instruc-
tions found in the users manual, may cause interference
harmful to the operation of other electronic devices. Com-
pliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to dis-
tribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Corporation
of America, Electronic Service Division, 6600 Orangetho-
rpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products dis-
tributed by Yamaha Corporation of America or its subsid-
iaries.
* This applies only to products distributed by Yamaha Corporation of America. (class B)
FCC INFORMATION (U.S.A.)
* This applies only to products distributed by
Yamaha Corporation of America.
COMPLIANCE INFORMATION STATEMENT
(Supplierʼs declaration of conformity procedure)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Digital Piano
Model Name : CLP-725
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference
that may cause undesired operation.
(FCC SDoC)
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important operating
and maintenance (servicing) instructions in
the literature accompanying the product.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by
the manufacturer.
12 Use only with the cart,
stand, tripod, bracket, or
table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid injury
from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
(UL60065_03)
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
For AC adaptor
4
CLP-725 Owner’s Manual
5
CLP-725 Owner’s Manual
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.
WARNING
This AC adaptor is designed for use with only Yamaha electronic
instruments. Do not use for any other purpose.
Indoor use only. Do not use in any wet environments.
CAUTION
When setting up, make sure that the AC outlet is easily accessible. If
some trouble or malfunction occurs, immediately turn off the power
switch of the instrument and disconnect the AC adaptor from the
outlet. When the AC adaptor is connected to the AC outlet, keep in
mind that electricity is flowing at the minimum level, even if the power
switch is turned off. When you are not using the instrument for a long
time, make sure to unplug the power cord from the wall AC outlet.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Do not place the power cord near heat sources such as heaters or
radiators. Also, do not excessively bend or otherwise damage the cord,
or place heavy objects on it.
Only use the voltage specified as correct for the instrument. The
required voltage is printed on the name plate of the instrument.
Use the specified adaptor (page 34) only. Using the wrong adaptor can
result in damage to the instrument or overheating.
Use only the supplied power cord/plug.
Check the electric plug periodically and remove any dirt or dust which
may have accumulated on it.
This instrument contains no user-serviceable parts. Do not open the
instrument or attempt to disassemble or modify the internal
components in any way. If it should appear to be malfunctioning,
discontinue use immediately and have it inspected by qualified
Yamaha service personnel.
Do not expose the instrument to rain, use it near water or in damp or
wet conditions, or place on it any containers (such as vases, bottles or
glasses) containing liquids which might spill into any openings. If any
liquid such as water seeps into the instrument, turn off the power
immediately and unplug the power cord from the AC outlet. Then have
the instrument inspected by qualified Yamaha service personnel.
Never insert or remove an electric plug with wet hands.
Do not put burning items, such as candles, on the unit. A burning item
may fall over and cause a fire.
Do not place the bench in an unstable position where it might
accidentally fall over.
Do not play carelessly with or stand on the bench. Using it as a tool or
stepladder or for any other purpose might result in accident or injury.
Only one person should sit on the bench at a time, in order to prevent
the possibility of accident or injury.
If the bench screws become loose due to extensive long-term use,
tighten them periodically using the specified tool in order to prevent
the possibility of accident or injury.
Keep special watch over any small children so that they don’t fall off
the rear of the bench. Since the bench does not have a backrest,
unsupervised use may result in accident or injury.
When one of the following problems occur, immediately turn off the
power switch and disconnect the electric plug from the outlet. Then
have the device inspected by Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the instrument.
- If any cracks or breakages exist on the instrument.
For the AC adaptor
For the instrument
Power supply/AC adaptor
Do not open
Water warning
Fire warning
Using the bench (If included)
If you notice any abnormality
DMI-7 1/2
6
CLP-725 Owner’s Manual
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the instrument or other property. These precautions include, but are not limited to, the following:
Do not connect the instrument to an electrical outlet using a multiple-
connector. Doing so can result in lower sound quality, or possibly
cause overheating in the outlet.
When removing the electric plug from the instrument or an outlet,
always hold the plug itself and not the cord. Pulling by the cord can
damage it.
Remove the electric plug from the outlet when the instrument is not to
be used for extended periods of time, or during electrical storms.
Assemble the instrument in the proper sequence by following the
assembly instructions in this manual. Also, make sure to tighten the
screws regularly. Failure to do so might result in damage to the
instrument or even injury.
Do not place the instrument in an unstable position where it might
accidentally fall over.
Do not go near the instrument during an earthquake. Strong shaking
during an earthquake could cause the instrument to move or tip over,
resulting in damage to the instrument or its parts, and possibly
causing injury.
When transporting or moving the instrument, always use two or more
people. Attempting to lift the instrument by yourself may damage your
back, result in other injury, or cause damage to the instrument itself.
Before moving the instrument, remove all connected cables, to prevent
damage to the cables or injury to anyone who might trip over them.
When setting up the product, make sure that the AC outlet you are
using is easily accessible. If some trouble or malfunction occurs,
immediately turn off the power switch and disconnect the plug from the
outlet. Even when the power switch is turned off, electricity is still
flowing to the product at the minimum level. When you are not using
the product for a long time, make sure to unplug the power cord from
the wall AC outlet.
Before connecting the instrument to other electronic components, turn
off the power for all components. Before turning the power on or off for
all components, set all volume levels to minimum.
Be sure to set the volumes of all components at their minimum levels
and gradually raise the volume controls while playing the instrument to
set the desired listening level.
Do not insert a finger or hand in any gaps on the key cover or
instrument. Also take care that the key cover does not pinch your
finger.
Never insert or drop paper, metallic, or other objects into the gaps on
the key cover, panel or keyboard. This could cause physical injury to
you or others, damage to the instrument or other property, or
operational failure.
Do not rest your weight on, or place heavy objects on the instrument,
and do not use excessive force on the buttons, switches or connectors.
Keep small parts out of the reach of infants. Your children may
accidentally swallow them.
Do not use the instrument/device or headphones for a long period of
time at a high or uncomfortable volume level, since this can cause
permanent hearing loss. If you experience any hearing loss or ringing
in the ears, consult a physician.
Always turn the power off when the instrument is not in use.
Even when the [ ] (Standby/On) switch is in standby status (power
indicator is off), electricity is still flowing to the instrument at the
minimum level.
When you are not using the instrument for a long time, make sure you
unplug the power cord from the wall AC outlet.
Power supply/AC adaptor
Assembly
Location
Yamaha cannot be held responsible for damage caused by improper use or
modifications to the instrument, or data that is lost or destroyed.
Connections
Handling caution
DMI-7 2/2
The model number, serial number, power requirements, etc., may be found on or
near the name plate, which is at the bottom of the unit. You should note this
serial number in the space provided below and retain this manual as a perma-
nent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
(bottom_en_01)
The name plate is located on the bottom of the unit.
7
CLP-725 Owner’s Manual
NOTICE
To avoid the possibility of malfunction/ damage to the product,
damage to data, or damage to other property, follow the notices
below.
Handling
Do not use the instrument in the vicinity of a TV, radio,
stereo equipment, mobile phone, or other electric devices.
Otherwise, the instrument, TV, or radio may generate noise.
When you use the instrument along with an app on your
smart device such as a smartphone or tablet, we recommend
that you enable “Airplane Mode” on that device in order to
avoid noise caused by communication.
Do not expose the instrument to excessive dust or
vibrations, or extreme cold or heat (such as in direct
sunlight, near a heater, or in a car during the day) to prevent
the possibility of panel disfiguration, damage to the internal
components or unstable operation. (Verified operating
temperature range: 5° – 40°C, or 41° – 104°F.)
Do not place vinyl, plastic or rubber objects on the
instrument, since this might discolor the panel or keyboard.
In the case of a model with a polished finish, bumping the
surface of the instrument with metal, porcelain, or other
hard objects can cause the finish to crack or peel. Use
caution.
Maintenance
When cleaning the instrument, use a soft and dry/slightly
damp cloth. Do not use paint thinners, solvents, alcohol,
cleaning fluids, or chemical-impregnated wiping cloths.
In the case of a model with a polished finish, gently remove
dust and dirt with a soft cloth. Do not wipe too hard since
small particles of dirt can scratch the instrument's finish.
During extreme changes in temperature or humidity,
condensation may occur and water may collect on the
surface of the instrument. If water is left, the wooden parts
may absorb the water and be damaged. Make sure to wipe
any water off immediately with a soft cloth.
Saving data
Some of the data of this instrument (page 29) are retained
when the power is turned off. However, the saved data may
be lost due to some failure, an operation mistake, etc. Save
your important data onto an external device such as a
computer (page 29).
Information
About copyrights
Copying of the commercially available musical data
including but not limited to MIDI data and/or audio data is
strictly prohibited except for your personal use.
This product incorporates and bundles contents in which
Yamaha owns copyrights or with respect to which Yamaha
has license to use others’ copyrights. Due to copyright laws
and other relevant laws, you are NOT allowed to distribute
media in which these contents are saved or recorded and
remain virtually the same or very similar to those in the
product.
* The contents described above include a computer
program, Accompaniment Style data, MIDI data, WAVE
data, voice recording data, a score, score data, etc.
* You are allowed to distribute medium in which your
performance or music production using these contents is
recorded, and the permission of Yamaha Corporation is
not required in such cases.
About functions/data bundled with the
instrument
Some of the preset songs have been edited for length or
arrangement, and may not be exactly the same as the
original.
About this manual
The illustrations as shown in this manual are for
instructional purposes only, and may appear somewhat
different from those on your instrument.
The letters at the end of the model name (such as “B,” “PE”)
indicate the color or finish of the instrument. Since they
simply indicate the appearance, these letters are omitted in
this manual.
Windows is a registered trademark of Microsoft®
Corporation in the United States and other countries.
iPad and iPhone are trademarks of Apple Inc., registered in
the U.S. and other countries.
Android™ is a trademark of Google LLC.
The company names and product names in this manual are
the trademarks or registered trademarks of their respective
companies.
Tuning
Unlike an acoustic piano, this instrument does not need to
be tuned by an expert (although the pitch can be user-
adjusted to match other instruments). This is because the
pitch of digital instruments is always maintained perfectly.
8
CLP-725 Owner’s Manual
Table of Contents
PRECAUTIONS .................................... 5
About the Manuals ................................ 9
Included Accessories ............................. 9
Panel Controls and Terminals ............10
Basic Operations
Setting Up.............................................11
Key Cover ..................................................................11
Music Rest .................................................................11
Turning the Power On.............................................12
Auto Power Off Function........................................12
Using Headphones ...................................................13
Playing the Piano..................................14
Using the Pedals........................................................14
Turning the VRM Effect On/Off............................14
Intelligent Acoustic Control (IAC)........................15
Grand Expression Modeling...................................15
Turning the Operation Confirmation Sounds
On/Off........................................................................16
Changing the Touch Sensitivity .............................16
Using the Metronome..............................................17
Advanced Operations
Playing Various Musical Instrument
Sounds (Voices)....................................18
Selecting a Voice.......................................................18
Listening to the Demo Songs ..................................19
Adding Variations to the Sound (Reverb) ............20
Transposing the Pitch in Semitones ......................21
Fine-tuning the Pitch ...............................................21
Layering Two Voices (Dual mode) ........................22
Playing Duo...............................................................23
Song Playback and Practice .................24
Listening to 50 Preset Songs....................................24
Listening to Songs Loaded from the Computer ...24
Practicing a One-Hand Part....................................25
Playing Back Immediately from the First Note
(Quick Play) ..............................................................25
Recording Your Performance .............26
Recording Your Performance ................................ 26
Changing the Initial Settings of the Recorded Song
....................................................................................27
Deleting Recorded Data ..........................................27
Using with a Computer or a Smart
Device ................................................... 28
Using an App on Your Smart Device.................... 28
Playback/Recording of Audio Data (USB Audio
Interface) ................................................................... 28
Backing up Data and Initializing the
Settings................................................. 29
Data Maintained When Power is Turned Off...... 29
Saving User Song data to a computer ...................29
Initializing the Settings............................................ 29
Confirming the firmware version of this
instrument................................................................. 29
Appendix
Troubleshooting ..................................30
Glossary of Terms ................................30
Keyboard Stand Assembly...................31
Specifications .......................................34
Index.....................................................35
9
CLP-725 Owner’s Manual
Thank you for purchasing this Yamaha Digital Piano!
This instrument provides exceptionally high-quality sound
and expressive control for your playing enjoyment.
We recommend that you read this manual carefully so that you can fully take advantage of the
advanced and convenient functions of the instrument. We also recommend that you keep this
manual in a safe and handy place for future reference.
About the Manuals
This instrument has the following manuals.
Included Manuals
Owner’s Manual (this book)
Explains how to use the instrument.
Quick Operation Guide (separate
sheet)
Shows in chart form the functions assigned to the
buttons and the keyboard for quick
understanding.
Online Manuals (PDF)
Smart Device Connection Manual
Explains how to connect the instrument to a smart
device such as smartphone or tablet, etc.
Computer-related Operations
Includes instructions on connecting this
instrument to a computer, and operations related
to transferring Song data.
MIDI Reference
Contains the MIDI Data Format and MIDI
Implementation chart, as well as descriptions on
MIDI functions such as MIDI channel and Local
Control settings.
To obtain these materials, access the Yamaha
Downloads website, then enter the model name for
searching the desired files.
NOTE
For a general overview of MIDI and how you can effectively use it,
search for “MIDI Basics” (only in English, German, French and
Spanish) on the website above.
Included Accessories
Owner’s Manual (this book) x1
Quick Operation Guide (separate sheet) x1
“50 Classical Music Masterpieces” (music book) x1
Online Member Product Registration x1
•Warranty* x1
•AC adaptor* x1
•Power cord* x1
•Bench* x1
* May not be included depending on your particular
area. Please check with your Yamaha dealer.
Yamaha Downloads
https://download.yamaha.com/
Smart device app “Smart Pianist
With the specially developed “Smart Pianist”
app running on your smart device, you can
remotely control your digital piano for even
more convenience and flexibility. By
presenting various parameters on-screen, this
app allows you to make settings in a visual,
more intuitive manner. For more details on
“Smart Pianist,” refer to the following Yamaha
website.
https://www.yamaha.com/kbdapps/
The connection wizard of the “Smart Pianist”
helps you to connect this instrument to your
smart device properly. To start the Connection
Wizard, tap ” (Menu) located at the upper
left of the screen to open the Menu display,
and then tap “Instrument” → “Start
Connection Wizard.”
10
CLP-725 Owner’s Manual
Panel Controls and Terminals
[ ] (Standby/On) switch......................... page 12
For turning the power on or setting to standby.
[MASTER VOLUME] knob
For adjusting the volume of the entire sound.
[DEMO/SONG] button..................... pages 19, 24
For playing the Demo Songs and the Preset Songs.
[PIANO/VOICE] button............. pages 18, 20, 22
For selecting a single Voice, two Voices for layering or
a Reverb Type.
[METRONOME] button .......................... page 17
For starting or stopping the metronome.
[+R], [–L] buttons ................. pages 17, 18, 24, 25
In general, these are for selecting the next or
previous Voice.
During Song playback, these are for selecting the
next or previous Song, and (while holding down
[PLAY]) turning on/off the right-hand and left-
hand Parts individually.
During Metronome playback, these are for
increasing or decreasing the Tempo.
[REC] button............................................ page 26
For recording your keyboard performance.
[PLAY] button.......................................... page 26
For playing back the recorded performance.
[FUNCTION] ................................... pages 12, 21
Simultaneously holding both [DEMO/SONG] and
[PIANO/VOICE] and pressing a specified key allows
you to change various settings, including Auto Power
off function, Transpose parameters, etc.
[PHONES] jacks....................................... page 13
For connecting a set of standard stereo headphones.
[USB TO HOST] terminal ....................... page 28
For connecting to a computer or a smart device such
as an iPhone or iPad.
[TO PEDAL] jack ..................................... page 32
For connecting the pedal cord.
DC IN jack................................................ page 12
For connecting the AC adaptor.
Pedals ....................................................... page 14
For controlling expression and sustain, just as on an
acoustic piano.
Bottom
(Keyboard side)
Bottom
(Keyboard side)
Bottom
(Keyboard side)
Music braces
Music rest
11
CLP-725 Owner’s Manual
Basic Operations
Setting Up
To open the key cover:
Lift the cover slightly, then push and slide it to the
end.
To close the key cover:
Slide the cover toward you and gently lower the
cover over the keys.
CAUTION
Hold the cover with both hands when opening or closing it.
Do not release it until it is fully opened or closed. Be
careful to avoid catching fingers (yours or others,
especially children’s) between the cover and main unit.
Do not place objects, such as a piece of metal or paper, on
top of the key cover. Small objects placed on the key cover
may fall inside the unit when the cover is opened and may
be nearly impossible to remove. This could cause electric
shock, short circuit, fire or other serious damage to the
instrument.
To raise the music rest:
Music braces allow you to hold the pages of music
books in place.
CAUTION
Do not try to use the music rest in a half-raised position.
When lowering the music rest, do not release your hands
from the music rest until it is all the way down.
To lower the music rest:
Close the Music braces if they are open, and then
lower the music rest by following the instructions
below.
Key Cover
CAUTION
Be careful to avoid catching
your fingers when opening or
closing the cover.
Music Rest
1
3
2
Music braces
3
1
2
Music braces
Setting Up
12
CLP-725 Owner’s Manual
1. Connect the plugs of the AC adaptor in
the order shown in the illustration.
WARNING
Use the specified adaptor (page 34) only. The use of
other adaptors may result in irreparable damage to both
the adaptor and the instrument.
CAUTION
When setting up the product, make sure that the AC
outlet you are using is easily accessible. If some trouble
or malfunction occurs, immediately turn off the power
switch and disconnect the plug from the outlet.
NOTE
Follow this procedure in reverse order when disconnecting
the AC adaptor.
2. Turn down the [MASTER VOLUME]
knob to “MIN.”
3. Press the [ ](Standby/On) switch to
turn the power on.
The power indicator on the button lights up to
indicate the power is on.
To adjust the volume of the entire keyboard sound,
use the [MASTER VOLUME] dial while playing the
keyboard.
When you’re ready to turn the power to standby,
press the [ ] (Standby/On) switch again for a
second. The power indicator turns off.
CAUTION
Even when the [ ] (Standby/On) switch is in the standby
status, electricity is still flowing to the instrument at a
minimum level. When not using the instrument for an
extended period of time, be sure to unplug the power
cord from the wall AC outlet.
CAUTION
Do not use this instrument at a high volume level for a
long period of time, to avoid damaging your hearing.
NOTICE
Press only the [ ] (Standby/On) switch when turning the
power on. Any other operations, such as pressing the
keys, buttons or pedals may cause the instrument to
malfunction.
To prevent unnecessary power consumption, this
instrument features an Auto Power Off function
that automatically turns the power off if the
instrument is not operated for approximately
30 minutes.
Default setting: Enabled
While holding down [DEMO/SONG] and
[PIANO/VOICE] simultaneously, press the A#0
key to enable the function or the A0 key to disable
it.
You can also disable the function when turning on
the power to the instrument.
While holding down the A-1 key (the lowest key,
press the [ ] (Standby/On) switch to turn the
instrument on. The [REC] indicator flashes three
times, indicating the Auto Power Off function has
been disabled.
Turning the Power On
AC outlet
AC adaptor
DC IN jack (page 10)
DC plug
Power cord
AC plug
The shape of the plug and outlet differ depending on the
locale.
2
3
Power
indicator
Auto Power Off Function
A#0 (Enable)
Lowest key
A0 (Disable)
Lowest key
Setting Up
13
CLP-725 Owner’s Manual
Since this instrument is equipped with two
[PHONES] jacks, you can connect two sets of
standard stereo headphones. If you are using only
one set of headphones, insert a plug into either
jack, which automatically shuts off the speakers
according to the default setting.
CAUTION
Do not use headphones at a high volume for an extended
period of time; doing so may cause hearing loss.
Using the headphone hanger
You can hang the headphones on this instrument.
For instructions on installing the headphone
hanger, refer to “Keyboard Stand Assembly” on
page 31.
NOTICE
Do not hang anything other than the headphones on the
hanger. Doing so may damage this instrument or the hanger.
Speaker On/Off setting
You can set whether the sound of this instrument is
always output from its built-in speaker or not.
While holding down [DEMO/SONG] and
[PIANO/VOICE] simultaneously, press one of the
D6 – E6 key.
Off (D6): The speaker will not sound.
On (D#6): The speaker will always sound regardless of
whether a set of headphones is connected or not.
Normal (E6): The speaker will sound only if
headphones are not connected. (This is the default
setting.)
NOTE
When this is set to “On,” Binaural Sampling and Stereophonic
Optimizer below are not effective.
Reproducing the Natural Sensation of
Sound Distance—Binaural Sampling
and Stereophonic Optimizer
This instrument features two advanced
technologies that allow you to enjoy exceptionally
realistic, natural sound, even when listening on
headphones.
Binaural Sampling (“CFX Grand” Voice only)
Binaural Sampling is a method that uses two
special microphones set at the ear position of a
performer and records the sound from a piano as it
would actually be heard. Listening to the sound
with this effect through headphones gives the
impression of being immersed in the sound, as if it
was actually emanating from the piano. Moreover,
you can enjoy the sound naturally for a long time
without ear fatigue. When the default Voice “CFX
Grand” (page 18) is selected, connecting the
headphones automatically enables the binaural
sampling sound.
Stereophonic Optimizer (Piano Voices other
than “CFX Grand”)
Stereophonic Optimizer is an effect which
reproduces the natural sound distance, like with
the sound of Binaural Sampling, even though you
are listening to it on headphones. When a piano
Voice other than “CFX Grand” is selected,
connecting the headphones automatically enables
the Stereophonic Optimizer.
Default setting: On
While holding down [PIANO/VOICE], press the
F#3 key to turn the function on or the F3 key to
turn the function off.
Using Headphones
PHONES
Standard stereo phone
plug
Bottom surface
F3 (Off)
C3
F#3 (On)
14
CLP-725 Owner’s Manual
Playing the Piano
Damper Pedal (Right)
Pressing this pedal will sustain notes longer.
Releasing this pedal immediately stops (damps)
any sustained notes. This pedal also features a
“half-pedal” function that creates partial sustain
effects, depending on how far down you press the
pedal.
Sostenuto Pedal (Center)
Pressing this pedal while holding the notes will
sustain the pressed notes (as if the Damper Pedal
had been pressed), but all subsequently played
notes will not be sustained. This makes it possible
to sustain a chord or single low note, for example,
while the other notes are played “staccato.”
Soft Pedal (Left)
Pressing this pedal will reduce the volume and slightly change the timbre of the
notes. The notes played before this pedal is pressed are not affected.
VRM (Virtual Resonance Modeling) technology accurately recreates the unique
resonance of an acoustic grand piano’s soundboard and strings. When you select
a piano Voice (page 18), pressing the damper pedal activates the VRM effect. For
details on VRM, see page 30.
While holding down [PIANO/VOICE], press the C#3 key to turn the function
on or the C3 key to turn the function off.
Using the Pedals
When you press the damper
pedal here, this note and the
notes you play before you release
the pedal sustain longer.
When you press the sostenuto
pedal here while holding the
note, the note will sustain as
long as you hold the pedal.
NOTE
If the damper pedal doesn’t
work, make sure that the pedal
cord is properly plugged into
the main unit (page 32).
Half-pedal function
This function allows you to vary
the sustain length depending
on how far the pedal is
pressed. The farther down you
press the pedal, the more the
sound sustains. For example, if
you press the damper pedal
and all notes you are playing
sound a bit murky and loud
with too much sustain, you can
release the pedal half way or
higher to decrease the sustain
(murkiness).
NOTE
While the sostenuto pedal is
held, the organ and strings
Voices sound continuously
without decay after the notes
have been released.
NOTE
When Jazz Organ Voice
(page 18) is selected,
pressing the left pedal
switches between fast/slow
rotation of the rotary speaker.
When the Vibraphone Voice
(page 18) is selected, the left
pedal switches Vibrato on and
off.
Turning the VRM Effe ct On/Off
Lowest key C3 (Off)
C#3 (On)
Default setting:
On
Playing the Piano
15
CLP-725 Owner’s Manual
With this function, the sound quality of this instrument is automatically adjusted
and controlled according to the overall volume. Even when the volume is low,
this lets you hear both low sounds and high sounds clearly.
To turn on/off IAC:
While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,
press the C#2 key to turn the function on or the C2 key to turn the function off.
To adjust IAC Depth:
While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,
press the D2 key to decrease the value, or the E2 key to increase.
The higher the value, the more clearly that low and high sounds are heard at
lower volume levels.
When a piano Voice (page 18) is selected, you can add Grand Expression
Modeling effects, which simulate the physical sound transitions of an actual
piano. When this feature is set to “Dynamic,” you can control extremely subtle
nuances in the performance and sound by changing your playing strength or
touch. When set to “Static,” the nuances are generally fixed. For details on Grand
Expression Modeling, see page 30.
While holding down [PIANO/VOICE], press the A#3 key to turn the function
on or the A3 key to turn the function off.
Intelligent Acoustic Control (IAC)
Default setting:
On
C#2 (On)
Lowest key
C2 (Off)
Setting range:
-3 – +3
Default setting:
0 (D#2)
Lowest key
D2 (Depth -1)
E2 (Depth +1)
D#2 (Default)
Grand Expression Modeling
Default setting:
Dynamic
A3 (Static)
A#3 (Dynamic)
Lowest key
Playing the Piano
16
CLP-725 Owner’s Manual
When a setup is changed using a button and key combination, an operation
sound (on, off, click, tempo value input) is sounded. This confirmation sound
can be enabled (on) or disabled (off) as desired.
While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,
press the A#-1 key to turn the sounds on or the A-1 key to turn the sounds off.
You can specify the Touch Sensitivity (how the sound responds to the way you
play the keys).
While holding down [PIANO/VOICE], press one of the C6 – D#6 keys.
Turning the Operation Confirmation Sounds On/Off
Default setting:
On
Lowest key A-1 (Off)
A#-1 (On)
Changing the Touch Sensitivity
NOTE
This setting is disabled with
some Voices, such as an
organ sound.
Default setting:
Medium (C#6)
Key
Touch
Sensitivity
Description
C6 Soft Produces relatively high volume even with light playing strength.
C#6 Medium Standard Touch Sensitivity.
D6 Hard Requires strong playing to produce high volume.
D#6Fixed
The volume level does not change at all regardless of whether you
play the keyboard soft or hard.
C6 Highest key (C7)D6
C#6D#6
Playing the Piano
17
CLP-725 Owner’s Manual
The metronome feature is convenient for practicing with an accurate tempo.
To start or stop the Metronome, press [METRONOME].
Metronome setting
Voice confirmation of current Tempo value (in English)
While holding down [METRONOME], press the A-1 key (lowest key).
Selecting the Beat (time signature)
While holding down [METRONOME], press one of the C3 – F3 keys.
The first beat is accented with a bell sound and the rest with clicks. Default set is
0 (C3). In this setting, clicks sound in all beats.
Adjusting the Tempo
The Metronome tempo can be set from 5 to 280 beats per minute.
To increase or decrease the value by 1:
While holding down [METRONOME], press [+R] to increase or [–L] to decrease.
While the metronome is playing, press [+R] to increase or [–L] to decrease.
To increase or decrease the value by 10:
While holding down [METRONOME], press the D2 key to increase or the C2 key
to decrease.
To specify a numeric value:
While holding down [METRONOME], press the relevant C1 – A1 keys one by one
in order, and then release [METRONOME] to enter the value.
Resetting the value to the default (120)
While holding down [METRONOME], press [+R] and [–L] simultaneously, or
press the C#2 key. While the metronome is playing, press [+R] and [–L]
simultaneously.
Adjusting the Volume
While holding down [METRONOME], press the G0 key to increase the volume
or the F0 key to decrease. To reset to the default setting, press the F#0 key while
holding down [METRONOME].
Using the Metronome
22447
13 3056 56
9
80
C#3D#3
D3 E3 F3F0 A1G0Lowest key A-1 C1 C2 D2 C3
C#2 (Default setting)F#0 (Default setting)
Volume BeatTempoConfirming the
current Tempo
Key Beat
C3 0 (no accent)
C#32
D3 3
D#34
E3 5
F3 6
Setting range:
1 – 10
Default setting:
7 (F#0)
NOTE
A numeric value is read out
when a relevant key is
pressed.
If the entered value is outside
the setting range, it will be
ignored.
18
CLP-725 Owner’s Manual
Advanced Operations
Playing Various Musical Instrument Sounds (Voices)
To select “CFX Grand”:
Simply press [PIANO/VOICE].
To select another Voice:
After pressing [PIANO/VOICE], press [+R] or [L] to select the next or previous
Voi ce .
To select a specific Voice:
While holding down [PIANO/VOICE], press one of the C1 – A1 keys. For details
on which Voice is assigned to each key, see the list below.
Voice List
Selecting a Voice
NOTE
To hear the characteristics of
the Voices, play back the
Demo Songs (page 19).
Key Voice Name Voice description
C1
CFX Grand
Yamaha’s CFX flagship concert grand piano sound with a wide dynamic
range for maximum expressive control. Suitable for playing in any music
genre and style.
Binaural
CFX Grand
Yamaha’s CFX flagship concert grand piano sound sampled by Binaural
Sampling, the method optimized for headphone use. Listening this
through headphones gives the impression of being immersed in the
sound, as if it was actually emanating from the piano. This Voice is
selected automatically when headphones are connected.
C#1 Bösendorfer
The famed sound of the Vienna-made Bösendorfer full concert grand
piano. Its spacious sound evokes the size of the instrument, and is ideal
for expressing tenderness in compositions.
D1 Pop Grand
Bright piano sound. Good for clear expression and “cutting through”
other instruments in an ensemble.
D#1 Stage E.Piano
The sound of an electric piano using hammer-struck metallic “tines.”
Soft tone when played lightly, and an aggressive tone when played
hard.
E1 DX E.Piano
An electronic piano sound created by FM synthesis. Good for standard
popular music.
F1 Harpsichord
The definitive instrument for baroque music. Since harpsichord uses
plucked strings, there is no touch response. There is, however, a
characteristic additional sound when the keys are released.
F#1 Vibraphone
Vibraphone played with relatively soft mallets. The tone becomes more
metallic the harder you play.
G1 Pipe Organ
This is a typical pipe organ sound (8 feet + 4 feet + 2 feet). Good for
sacred music from the Baroque period.
G#1 Jazz Organ
The sound of a “tonewheel” type electric organ. Often heard in jazz and
rock music.
A1 Strings
Stereo-sampled, large-scale strings ensemble with realistic reverb. Try
combining this Voice with piano in the Dual mode.
C#1D#1F#1G#1
C1 D1 E1 F1 G1 A1Lowest key
Playing Various Musical Instrument Sounds (Voices)
19
CLP-725 Owner’s Manual
Special individual Demo Songs are provided for all of the instrument Voices.
1. Press [DEMO/SONG] to start playback.
The Demo Song for the current Voice starts. During playback, the [PLAY] lamp
flashes at the current tempo.
Starting with the selected song, the playback of the Demo Songs will continue.
After the last demo song, the sequence then returns to the first Demo Song and
repeats until you stop it.
To change the Demo Song during playback:
Press [+R] or [–L] to change to the next or previous Demo Song.
To change to a specific Demo Song, simultaneously hold down [DEMO/SONG]
and press one of the C1 – A1 keys.
2. Press [DEMO/SONG] or [PLAY] to stop playback.
The [PLAY] lamp turns off.
Demo Song List
The Demo Songs excluding original Songs are short rearranged excerpts from the original
compositions. The original Demo Songs are Yamaha originals (© Yamaha Corporation).
Listening to the Demo Songs
NOTE
If you want to change the
playback tempo, see page 17.
Key Voic e Name Title Composer
C1
CFX Grand
Allegro de concierto Cis-Dur E. Granados
Binaural
CFX Grand
C#1 Bösendorfer Widmung S.566 R.253
F. Liszt /
R. Schumann
D1 Pop Grand Original
D#1 Stage E.Piano Original
E1 DX E.Piano Original
F1 Harpsichord
Concerto a cembalo obbligato, 2 violini, viola e
continuo No.7, BWV 1058
J. S. Bach
F#1 Vibraphone Original
G1 Pipe Organ Herr Christ, der ein'ge Gottes-Sohn, BWV 601 J. S. Bach
G#1 Jazz Organ Original
A1 Strings Original
Lowest key C1 A1
Playing Various Musical Instrument Sounds (Voices)
20
CLP-725 Owner’s Manual
This instrument features several Reverb Types that add extra depth and expression to the sound to create a
realistic acoustic ambience. The appropriate Reverb Type and Depth are called up automatically when you
select each of the Voices and Songs. For this reason, the Reverb Type need not be selected; however, you can
change it if desired.
To select a Reverb Type:
While holding down [PIANO/VOICE], press one of the C2 – E2 keys.
Reverb Type List
To adjust Reverb Depth:
While holding down [PIANO/VOICE], press the G2 key to decrease the value by
1 or the A2 key to increase the value by 1.
While holding down [PIANO/VOICE], press the G#2 key to reset the Reverb
Depth to the default setting, which is the most suitable value for the current
Voi ce .
Adding Variations to the Sound (Reverb)
Reverb in Dual Mode
(page 22)
An optimum reverb type for the
combination of Voices is
assigned automatically.
Key Reverb Type Description
C2 Recital Hall
Simulates the clear reverb sound you would hear in a medium-
sized concert hall for piano recitals.
C#2 Concert Hall
Simulates the gorgeous reverb sound you would hear in a large
concert hall for orchestral performances.
D2 Chamber
Suitable for playing chamber music; simulates the intimate
reverb sound you would hear in a spacious room, such as for
classical music recitals.
D#2Club
Simulates the vivid reverb sound you would hear in a live music
venue or a jazz club.
E2 Off No effect is applied.
Lowest key
A2 (Depth +1)
G#2 (Default)
G2 (Depth -1)
C#2D#2
C2 D2 E2
Reverb Type
Reverb Depth
Setting range:
0 (no effect) – 20 (maximum
depth)
Playing Various Musical Instrument Sounds (Voices)
21
CLP-725 Owner’s Manual
You can shift the pitch of the entire keyboard up or down in semitones in order to facilitate playing in
difficult key signatures, or to easily match the pitch of the keyboard to the range of a singer or other
instruments. For example, if “+5” is selected, playing key C produces pitch F, letting you play a song of F
major as though it were in C major.
To transpose the pitch down:
While holding down [DEMO/SONG] and [PIANO/VOICE], press a key
between F#2 (-6) and B2 (-1).
To transpose the pitch up:
While holding down [DEMO/SONG] and [PIANO/VOICE], press a key
between C#3 (+1) and F#3 (+6).
To restore the normal pitch:
While holding down [DEMO/SONG] and [PIANO/VOICE], press the C3 key.
You can fine-tune the pitch of the entire instrument in about 0.2 Hz steps. This lets you accurately match the
keyboard pitch to that of other instruments or CD music.
To tune up (in about 0.2 Hz steps):
Press and hold down [DEMO/SONG] and
[PIANO/VOICE] simultaneously, and press [+R].
To tune down (in about 0.2 Hz steps):
Press and hold down [DEMO/SONG] and
[PIANO/VOICE] simultaneously, and press [–L].
To set the pitch to 442.0 Hz:
Press and hold down [DEMO/SONG]
and [PIANO/VOICE] simultaneously,
and press the C#1 key.
To restore default pitch (440.0 Hz):
While simultaneously holding down [DEMO/
SONG] and [PIANO/VOICE], press [+R] and
[–L] simultaneously. Alternately, you can press
the C1 key while holding down [DEMO/
SONG] and [PIANO/VOICE] simultaneously.
Transposing the Pitch in Semitones
NOTE
The transposition setting
affects not only the pitch of the
keyboard but also the pitch of
Song playback (page 24).
The transposition setting of the
Transposition for the Keyboard
and the Song cannot be set
independently.
Setting range:
-6 – 0 – +6
Default setting:
0
-5 -3 -1 0 +2 +4 +5
-6 -4 -2 +1
+3 +6
F#2
Lowest key
F#3
Transpose down Transpose up
C3 (Normal pitch)
Fine-tuning the Pitch
Hz (Hertz)
This unit of measurement
refers to the frequency of a
sound and represents the
number of times a sound wave
vibrates in a second.
Setting range:
414.8 – 466.8 Hz
Default setting:
A3 = 440.0 Hz
C#1
Lowest key
Playing Various Musical Instrument Sounds (Voices)
22
CLP-725 Owner’s Manual
You can layer two Voices and play them simultaneously to create a more richly textured sound.
1. Engage the Dual mode.
While holding down [PIANO/VOICE], simultaneously hold down two keys
between C1 and A1 to select the two desired Voices. For information on which
Voices are assigned to the keys, refer to “Voice List” (page 18).
The Voice assigned to the lower key will be designated as Voice 1, and the Voice
assigned to the higher key will be designated as Voice 2. You cannot assign the same
Voice to both Voice 1 and Voice 2 simultaneously in Dual mode.
To shift the Octave for each Voice:
While holding down [PIANO/VOICE], press one of the keys F5 – G5 or A5 – B5 as
shown in the illustration below. For example, pressing the B5 key twice while
holding down [PIANO/VOICE] shifts Voice 1 up by two octaves. To restore the
default setting, simultaneously hold down [PIANO/VOICE] and press the A#5 key
for Voice 1 or the F#5 key for Voice 2.
To adjust the Balance between two Voices:
While holding down [PIANO/VOICE], press the C5 key to decrease the value or
the D5 key to increase. Pressing the C5 key increases the volume of Voice 2, while
pressing the D5 key increases the volume of Voice 1. To reset to the default value for
each combination of Voices, press the C#5 key.
2. To exit from Dual mode, press [PIANO/VOICE].
Layering Two Voices (Dual mode)
C1 A1
Lowest key
Engaging Dual mode
NOTE
The Dual and Duo modes
(page 23) cannot be engaged
at the same time.
Setting range:
-2 – 0 – +2
Setting range:
-6 – (default setting) – +6
Default setting:
Differs depending on the Voice
combination.
-1
0
+1-1 +1 -1
0
+1
C5
Highest key
C#5
(Default setting)
F5 B5
Shifting the octave
Adjusting the balance
Voice 2
Voice 1
D5
Playing Various Musical Instrument Sounds (Voices)
23
CLP-725 Owner’s Manual
This function allows two different players to play the instrument, one on the left and the other on the right,
over the same octave range and with the same Voice.
1. While holding down [PIANO/VOICE], press [+R] and [–L]
simultaneously to engage Duo.
The keyboard is divided into two sections, with the E3 key as the Split Point.
2. One person can play the left section of the keyboard while
the other plays the right.
The pedal function changes as follows.
Right Pedal: Applies Sustain to the right section.
Center Pedal: Applies Sustain to both sections.
Left Pedal: Applies Sustain to the left section.
To shift the O ctave for e a ch sec tion:
Same operation as in Dual (page 22).
To adjust the volume balance between two keyboard sections:
Same operation as in Dual (page 22).
3. To exit from Duo, simultaneously hold down [PIANO/
VOICE] and press [+R] and [–L].
Selecting the Duo type
You can set how the sound is emitted from the speakers. When you select
“Separated,” the sound of left part is emitted from the left speaker, and the sound
of right section is emitted from the right speaker. When you select “Balanced,”
the sound of both parts are emitted from both speakers in a natural balance.
While holding down [PIANO/VOICE], press the A4 key or the A#4 key to
change the setting.
Playing Duo
NOTE
• The Split Point cannot be
changed from E3.
• In Duo, VRM is not effective.
• When the Duo type is set to
“Separated,” Reverb and
Binaural Sampling/
Stereophonic Optimizer are
not effective.
• If the keyboard is in Dual
mode, engaging Duo will exit
from Dual, and Voice 1 is
used over the entire range of
the keyboard.
Split Point E3
Equivalent to C3
(middle C)
Left section (Voice 2) Right section (Voice 1)
Equivalent to C3
(middle C)
Setting range:
-2 – 0 – +2
Setting range:
-6 – 0 – +6
Default setting:
Separated
Highest keyA4 (Separated) A#4 (Balanced)
24
CLP-725 Owner’s Manual
Song Playback and Practice
In addition to the Demo Songs, Preset Songs are provided for your listening pleasure.
1. Find the number of the Song that you want to play back
from the included “50 Classical Music Masterpieces.”
2. While holding down [DEMO/SONG], press one of the C2 –
C#6 keys to start playback.
The number of each piano Preset Song is assigned to the C2 – C#6 keys.
During playback, the [+R] and [–L] lamps light, and the [PLAY] lamp flashes at the
current tempo. Playback of the Preset Songs continues in sequence, starting with
the selected song. After the last Preset Song, the sequence then returns to the first
Preset Song and repeats until you stop it.
To change the Preset Song during playback:
Press [+R] or [–L] to change to the next or previous Preset Song, or directly select the
desired Song by holding down [DEMO/SONG] and pressing the appropriate key.
To change the tempo during playback:
While holding down [METRONOME], press [+R] or [–L] to increase or decrease
the Tempo value by 1. Other instructions are the same as those of the Metronome
Tempo (page 17).
To play back from the beginning of the Song
During playback, press [+R] and [–L] simultaneously to jump to the playback
position at the beginning of the Song then continue playback at the last specified
tempo.
3. Press [DEMO/SONG] or [PLAY] to stop playback.
The [PLAY], [+R] and [–L] lamps turn off.
You can transfer up to 10 songs from your computer to this instrument and play
them back. For details on transferring Songs from a computer and playing them
back on this instrument, refer to the “Computer-related Operations” section on
the website (page 9).
Types of file that can be exchanged with a computer
Files with a .mid extension (SMF format 0 or 1)
Listening to 50 Preset Songs
Highest key (C7)
Song 1 Song 10 Song 20 Song 30 Song 40
C3 C4 C5
C2
Song 50 (C#6)
NOTE
You can play the keyboard
along with the Preset Song.
You can also change the Voice
played from the keyboard.
Song:
In this manual, performance
data is called a “Song.” This
includes 50 Preset Songs and
Demo Songs.
NOTE
The Preset Songs, Demo
Songs and other Songs (a
maximum of ten) transferred
from a computer can be
played back consecutively
within each category.
NOTE
You can import additional
Songs by loading SMF files
from a computer. For details,
refer to the “Computer-related
Operations” on the website
(page 9).
Listening to Songs Loaded from the Computer
NOTE
Certain MIDI files in SMF format
0 or 1 may contain data that is
not supported by your digital
piano, and such files may not
play as originally intended. If
this is the case, setting the song
playback channels to “1&2”
may enable a better rendition of
the song. For details, refer to
the “Computer-related
Operations” section on the
website (page 9).
Song Playback and Practice
25
CLP-725 Owner’s Manual
All the Songs except for the Demo (page 19) let you turn on or off the left-hand and right-hand Parts
individually. By turning off [+R], for example, you can practice the right-hand Part while the left-hand Part
is playing back, and vice versa.
1. Start playback of a Preset Song (page 24) or the User Song
(page 26).
2. While holding down [PLAY], press [+R] or [–L] to turn the
Part on/off.
Pressing the same button repeatedly while holding down [PLAY] toggles playback on
and off. The lamp of the button lights to indicate that the corresponding Part is on.
3. Practice the Part which is turned off.
To change the Tempo :
While holding down [METRONOME], press [+R] or [-L] to increase or decrease
the Tempo value by 1. Other instructions are the same as those of the Metronome
Tempo (page 17).
4. Press [PLAY] to stop playback.
This Quick Play feature enables you to specify whether a Song should play back
immediately from the very first note, or play back any silence or rests that exist
before the first note.
To turn on/off Quick Play:
While holding down [DEMO/SONG], press the A#-1 to turn the function on or
A-1 key to turn the function off.
Practicing a One-Hand Part
NOTE
Selecting another Song will
reset the on/off status.
NOTE
Songs 16 – 20 of “50 Classical
Music Masterpieces” are duet
songs. The right-hand Part is
for the first player, and the left-
hand Part is for the second
player.
or Lamp lights when Part is on.
Playing Back Immediately from the First Note (Quick Play)
Default setting:
On
A#-1(On)
A-1(Off)
Lowest key
26
CLP-725 Owner’s Manual
Recording Your Performance
Not only can you simply record your keyboard performance (Quick Recording), but you can record two
parts (left-hand and right-hand) separately. The recorded data is called a User Song, and can be saved to a
computer as a Standard MIDI file (SMF; page 29).
1. Select the desired Voice and other parameters, such as beat
(time signature), for recording.
For instructions on selecting a Voice, refer to page 18. If necessary, set other
parameters, such as beat (time signature) and effects, in this step.
2. Engage the Record Ready mode.
Quick Recording
Press [REC] to engage the Record Ready mode. Your keyboard performance will be
automatically recorded to the right-hand part. Note that the already-recorded data
of the right- and left-hand parts will be erased by Quick Recording.
Recording to individual parts
While holding down [REC], press [+R] or [–L] to engage the Record Ready mode
for the Part you want to record.
If data has already been recorded to the other Part, the data in this Part will be
played back while recording.
To turn the Part off or on, press the appropriate part button ([+R] or [-L]) while
holding down [PLAY].
To exit from Record Ready mode:
Simply press [REC].
3. Play the keyboard or press [PLAY] to start recording.
The [REC] lamp lights up while the Recording Part lamp flashes at the current
tempo.
4. Press either [REC] or [PLAY] to stop recording.
The [REC], [PLAY], [+R] and [–L] lamps flash, indicating that the recorded data is
being stored. After the Save operation is completed, the lamps will turn off,
indicating that the Record operation has been completed.
5. To hear the recorded Song, press [PLAY] to start playback.
Press [PLAY] again to stop playback.
To record to the other part
Repeat the steps above. In step 2, follow the instructions of “Recording individual
parts.”
Recording Your Performance
NOTE
The Recording function of this
instrument will record your
keyboard performance as
MIDI data. If you want to
record audio data, you can
connect a computer to the
instrument for that purpose.
Refer to page 28 for details.
NOTE
You can use the Metronome
while recording; however, the
Metronome sound will not be
recorded.
NOTE
If the keyboard is in the Duo
mode (page 23), the data will
be recorded to each Part. The
Part for recording cannot be
specified.
NOTICE
Note that recording your
performance to a part
containing data will replace
already-recorded data with
the new data.
NOTE
If the data capacity of the
instrument approaches full
when you engage Record
Ready mode, the [REC] and
[PLAY] lamps flash quickly for
about three seconds.
To record the right-hand Part ([+R]) To record the left-hand Part ([–L])
NOTICE
Never turn off the power
while the recorded data is
being stored (while the
lamps are flashing).
Otherwise, all recorded data
will be lost.
Recording Capacity
This instrument can record up
to 250 KB (approximately
11,000 notes).
Recording Your Performance
27
CLP-725 Owner’s Manual
The settings of the following parameters can be changed after the Record operation is completed.
For individual Parts: Voice, Volume balance (Dual/Duo), Reverb Depth
For the entire Song: Tempo, Reverb Type
1. Make settings for the above parameters as desired.
2. While holding down [REC], press the desired Part button to
engage Record Ready mode.
The [REC], [PLAY] and selected Part ([+R] or [–L]) lamps flash.
In this status, do not press [PLAY] again or any key. Otherwise, the originally
recorded performance data will be deleted.
3. While holding down [REC], press [PLAY] to exit from
Record Ready mode.
The [REC], [PLAY], [+R] and [–L] lamps flash. After the Save operation is
completed, the lamps will turn off, indicating that the operation has been
completed.
Confirm the setting by playing the Song.
To delete the entire Song:
1. While holding down [REC], press [DEMO/SONG].
The [REC] and [PLAY] lamps flash alternately.
To exit from this status, press [REC].
2. Press [PLAY] to delete the data of the entire Song.
The [REC], [PLAY], [+R] and [–L] lamps flash.
After the operation is completed, all lamps turn off.
To delete a specific Part:
1. While holding down [REC], press [+R] or [–L] (depending
on the Part you want to delete) to engage Record Ready
mode.
The [REC], [PLAY] and selected Part ([+R] or [–L]) lamps flash.
2. Press [PLAY] to start recording without playing the
keyboard.
The selected Part ([+R] or [–L]) lamp flashes.
3. Press [REC] or [PLAY] to stop recording.
All data recorded for the selected Part will be deleted, and the lamp turns off.
Changing the Initial Settings of the Recorded Song
Deleting Recorded Data
NOTE
If a User Song has not been
recorded to the instrument, the
[REC] and [PLAY] lamps flash
quickly for about three
seconds.
28
CLP-725 Owner’s Manual
Using with a Computer or a Smart Device
By connecting a computer or a smart device to the [USB TO HOST] terminal via a USB cable, you can
transmit/receive performance data and Song data to/from the computer or smart device.
For instructions on connection and transmitting/receiving MIDI data with a
computer, refer to the “Computer-related Operations” on the website (page 9).
For instructions on connection with a smart device, refer to the “Smart Device
Connection Manual” on the website. If you use the smart device app “Smart
Pianist” with the instrument, the connection wizard on the app helps you to
connect the instrument to your smart device properly. For details, see page 9.
By using an app on a smart device, you can take advantage of convenient functions and get more enjoyment
out of this instrument. In particular, with the “Smart Pianist” app running on your smart device, you can
remotely control your digital piano for even more convenience and flexibility.
For information about the compatible smart devices and apps, access the following page:
https://www.yamaha.com/kbdapps/
You can play back audio data on a smart device or a computer with this
instrument. You can also record your keyboard performance as audio data to a
music production app on a smart device or a computer.
Audio Loopback On/Off
You can set whether audio sound input from the [USB TO HOST] terminal is
output to a computer or smart device or not, along with the performance played
on the instrument (Audio Loopback function). To output the audio input sound,
set Audio Loopback to “On.
While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,
press the G5 key to turn this parameter “Off” or the G#5 key to turn it “On.”
NOTICE
Use an AB type USB cable
of less than 3 meters. USB
3.0 cables cannot be used.
Do not place your smart
device in an unstable
position. Doing so may
cause the device to fall and
result in damage.
NOTE
For instructions on using MIDI,
refer to the online manual
“MIDI Reference” (page 9).
Instrument
USB cable
USB conversion
adaptor
Smart device
Computer
USB terminal
Instrument
USB cable
Using an App on Your Smart Device
Playback/Recording of Audio Data (USB Audio Interface)
NOTE
The volume of the audio sound
input can be adjusted from a
computer or a smart device.
When using this function on a
computer running Windows,
you will need to install the
Yamaha Steinberg USB Driver
to the computer. For details,
refer to the “Computer-related
Operations” on the website
(page 9).
Default setting: On
NOTICE
If you are using a DAW (digital
audio workstation) with this
instrument, set the Audio
Loopback to OFF. Otherwise,
loud noises may occur,
depending on the settings of
the computer/smart device or
the application software.
G#5 (On)
G5 (Off)
Highest key
29
CLP-725 Owner’s Manual
Backing up Data and Initializing the Settings
The following settings and data are maintained even if you turn the power off.
Among the data listed above, only User Song data (USERSONG00.MID) can be
transferred to a computer and saved as an SMF file. For details, refer to the
“Computer-related Operations” on the website (page 9).
With this operation, all data (with the exception of the Songs) will be reset to the
factory default settings.
To do this, simultaneously hold down the C7 (the highest) key and turn on the
power.
You can confirm the firmware version of your instrument by audible voice in English.
While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously, press the B0 key.
About the latest Firmware Version
Yamaha may from time to time update firmware of the product without notice for improvement. Make sure
to check our website for information of the latest release and upgrade the firmware for your instrument.
Data Maintained When Power is Turned Off
•Metronome Volume
Metronome Beat (time signature)
Touch Sensitivity
•Tuning
Intelligent Acoustic Control Depth
Intelligent Acoustic Control On/Off
Binaural Sampling/Stereophonic Optimizer On/Off
Operation Confirmation Sounds On/Off
Auto Power Off Enable/Disable
•Speaker On/Off
Duo type Separated/Balanced
•User Song data
Song data (SMF files) transferred from a computer
Saving User Song data to a computer
NOTICE
Saved data may be lost due
to malfunction or incorrect
operation. Save important
data to an external device
such as a computer.
Initializing the Settings
NOTICE
Never turn off the power
while the Initialize operation
is being executed (that is,
while the [REC], [PLAY], [+R]
and [–L] lamps are flashing).
NOTE
If this instrument somehow
becomes disabled or
malfunctions, turn off the
power then execute
Initialization.
C7
Highest key
Confirming the firmware version of this instrument
Lowest key
B0
30
CLP-725 Owner’s Manual
Appendix
Troubleshooting
Glossary of Terms
VRM (Virtual Resonance Modeling)
On an actual acoustic piano, if you press the damper pedal and play a key, not only does the string of the pressed key vibrate, it
also causes other strings and the soundboard to vibrate, with each influencing the rest, creating a rich and brilliant resonance that
sustains and expands. The VRM technology featured in this instrument reproduces the complicated interaction between both
string and soundboard resonance, and make the sound more like that of a real acoustic piano. Since resonance instantaneously
occurs depending on the action of the keys and pedal, you can expressively vary the sound by changing the timing of your
pressing the keys, and the timing and depth of your pressing the pedal.
Grand Expression Modeling
On an actual acoustic piano, subtle changes in the sound can be produced by changing your playing touch from when you press
a key to when you release it. For example, when you press a key all the way to its bottom, the key hits the keybed underneath and
the noise reaches the strings, changing the sound slightly. Furthermore, the tone when the damper is lowered onto strings to mute
the sound is changed by how quickly you release the key. The Grand Expression Modeling technology recreates these subtle
changes in the sound that respond to your touch. This allows you to add accents by playing strongly or add resonance by playing
softly to produce superbly expressive sound. A crisp tone can be heard when playing staccato as well as a lingering sound
produced when releasing the keys slowly.
Problem Possible Cause and Solution
Power suddenly and unexpectedly
turns off.
This is normal and the Auto Power Off function may have been activated (page 12).
If desired, disable the Auto Power Off function.
The instrument does not turn on.
The plugs are not properly connected. Make sure that the DC plug is securely inserted
into the DC IN jack on the instrument, and that the AC plug is securely inserted to the AC
outlet (page 12).
A click or pop is heard when the
power is turned on or off.
This is normal when electrical current is being applied to the instrument.
Noise is heard from the speakers
or headphones.
The noise may be due to interference caused by the use of a mobile phone in close
proximity to this instrument. Turn off the mobile phone, or move it further away from this
instrument.
Metronome or Song goes out of
tempo slightly when you play the
keyboard.
This occurs infrequently when Grand Expression Modeling is set to “Dynamic.” If this
happens, set Grand Expression Modeling to “Static” (page 15).
The overall volume is low, or no
sound is heard.
The Master Volume is set too low. Set it to an appropriate level using the [MASTER
VOLUME] knob (page 10).
Make sure a pair of headphones or conversion adaptor is not connected to the
[PHONES] jack (page 13).
The Speaker setting is “Off.” Set the Speaker to “Normal” or “On” (page 13).
Make sure that Local Control is On. For details, refer to the “MIDI Reference” (page 9).
Pedals do not function.
The pedal cord may not be securely connected to the [TO PEDAL] jack. Be sure to
insert the pedal cord all the way until the metal part of the cord plug disappears from
view (page 32).
The damper pedal does not
function as expected.
The damper pedal was pressed when the power was turned on. This is not a
malfunction; release the pedal and press it again to reset the function.
31
CLP-725 Owner’s Manual
Keyboard Stand Assembly
CAUTION
Assemble the unit on a hard and flat floor with ample space.
Be careful not to confuse parts, and be sure to install all
parts in the correct orientation. Please assemble the unit in
accordance with the sequence given below.
Assembly should be carried out by at least two persons.
Be sure to use only the included screws of the specified
sizes. Do not use any other screws. Use of incorrect screws
can cause damage or malfunction of the product.
Be sure to tighten all screws upon completing assembly of
the unit.
To disassemble the unit, reverse the assembly sequence
given below.
Remove all parts from the package and make sure you
have all of the items.
1. Attach (finger-tighten) C to D and
E.
1-1 Untie and straighten out the bundled pedal
cord.
1-2 Align D and E with each end of C.
1-3 Attach D and E to C by finger-tightening
the long screws (6 x 20 mm).
2. Attach B.
2-1 Align the screw holes on the upper side of B
with the bracket holes on D and E, then
attach the upper corners of B to D and E by
finger-tightening two thin screws (4 x 12
mm).
2-2 While pushing the lower part of D and E
from outside, secure the bottom ends of B
using two tapping screws (4 x 20 mm).
Have a Phillips-head (+) screwdriver of the appropriate size
ready.
Foamed styrol pads
Remove foamed styrol pads from the package, position them on
the floor, then place A on top of them. Position the pads so that
they will not hide the connectors on the bottom of A.
Bundled pedal
cord inside
6 x 20 mm long screws x 4
4 x 12 mm thin screws x 2
4 x 20 mm tapping screws x 4
6 x 16 mm short screws x 6
Power cord x 1
AC adaptor x 1
The power cord and adaptor
may not be included, or may
look different from the illustration
above, depending on your
particular area. Please check
with your Yamaha dealer.
4 x 10 mm thin screws x 2
Cord holder
Headphone hanger x 1
Caps x 4
1-1
1-3
2-1
2-2
2-2
2-3
2-2
Keyboard Stand Assembly
32
CLP-725 Owner’s Manual
2-3 Insert the other two tapping screws (4 x 20
mm) into the other two screw holes to
secure B.
2-4 Securely tighten the screws on the top of B
that were attached in Step 2-1.
3. Secure C.
3-1 Securely tighten the screws on C that were
attached in Step 1-3.
3-2 Attach the caps to the head of the screws.
4. Mount A.
Be sure to place your hands at least 15 cm away
from either end of the main unit when positioning
it.
CAUTION
Be extra careful not to drop the main unit or let your fingers
be pinched by it.
Do not hold the main unit in any position other than the
position specified above.
5. Secure A.
5-1 Adjust the position of A so that the left and
right ends of A will project beyond D and E
equally when seen from the front.
5-2 Secure A by tightening the short screws (6 x
16 mm) from the front.
6. Connect the pedal cord and the AC
adaptor.
3-1
3-2
3-2
Align the screw holes.
At least 15 cm
5-1
5-2
6
-
2
6
-
1
6
-
4
Keyboard Stand Assembly
33
CLP-725 Owner’s Manual
6-1 Insert the pedal cord plug to the pedal
connector from the rear.
6-2 Securely wind the cord holder around the
pedal cord.
The cord holder is attached to D.
6-3 Connect one end of the power cord to the
AC adaptor.
6-4 Insert the DC plug of the AC adaptor into
the DC IN jack.
7. Set the adjuster.
Rotate the adjuster until it comes in firm contact
with the floor surface.
8. Attach the headphone hanger.
Use two thin screws (4 x 10 mm) to attach the
hanger as shown in the illustration.
When connecting the pedal
cord, insert the plug securely
until the metal part
disappears from view.
After completing the assembly, please check the
following.
Are there any parts left over?
Review the assembly procedure and correct any
errors.
Is this instrument clear of doors and other
movable fixtures?
Move the instrument to an appropriate location.
Does this instrument make a rattling noise when
you shake it?
Tighten all screws.
Does the pedal box rattle or give way when you
step on the pedals?
Turn the adjuster so that it is set firmly against the
floor.
Are the pedal cord plug and the adaptor plug
inserted securely into the sockets?
Check the connection.
CAUTION
When moving the instrument, always hold the bottom of
the main unit. Do not hold the key cover or top portion.
Improper handling can result in damage to the
instrument or personal injury.
Transporting
If you move to another location, you can transport the
instrument along with other belongings. You can move the
unit as it is (assembled), or you can disassemble the unit
down to the condition it was in when you first took it out of
the box. Transport the keyboard horizontally. Do not lean
it up against a wall or stand it up on its side. Do not subject
the instrument to excessive vibration or shock. When
transporting the assembled instrument, make sure all
screws are properly tightened and have not been loosened
by moving the instrument.
CAUTION
If the main unit creaks or is otherwise unsteady when
you play on the keyboard, refer to the assembly
diagrams and re-tighten all screws.
Do not hold here.
Hold here.
Separate the adjuster
from the floor surface.
34
CLP-725 Owner’s Manual
Specifications
* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download
the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.
CLP-725
Product Name Digital Piano
Size/Weight
Width
[For models with polished finish]
1,350 mm (53-1/8")
[1,353 mm (53-1/4")]
Height
[For models with
polished finish]
With music rest closed
849 mm (33-7/16")
[851 mm (33-1/2")]
With music rest raised
1,003 mm (39-1/2")
[1,004 mm (39-1/2")]
Depth
[For models with polished finish]
414 mm (16-5/16")
[415 mm (16-5/16")]
Weight
[For models with polished finish]
43 kg (94 lb, 13 oz)
[45 kg (99 lb, 3 oz)]
Control
Interface
Keyboard
Number of Keys 88
Type GrandTouch-S Keyboard: synthetic ebony and ivory key tops, escapement
Touch Response Hard/Medium/Soft/Fixed
Pedal Number of Pedals 3: Damper (with Half-pedal function), Sostenuto, Soft
Panel Language English
Cabinet
Key Cover Style Sliding
Music Rest Yes (with music braces)
Voices
Tone Generation
Piano Sound Yamaha CFX, Bösendorfer Imperial
Binaural Sampling Yes (CFX Grand Voice only)
Piano Effect
VRM Yes
Grand Expression Modeling Yes
Key-off Samples Yes
Smooth Release Yes
Polyphony (max.) 256
Preset Number of Voices 10
Effects
Types
Reverb 4 types
Intelligent Acoustic Control (IAC) Yes
Stereophonic Optimizer
Yes
Functions
Dual Yes
Duo Yes
Recording/
Playback
(MIDI data
only; audio not
supported.)
Preset Number of Preset Songs 10 Voice Demo Songs, 50 Classics
Recording
Number of Songs 1
Number of Tracks 2
Data Capacity Approx. 250 KB/Song (approx. 11,000 notes)
Format
Playback SMF (Format 0, Format 1)
Recording SMF (Format 0)
Functions Overall Controls
Metronome Yes
Tempo Range 5 – 280
Transpose -6 – 0 – +6
Tuning 414.8 – 440.0 – 466.8 Hz (approx. 0.2 Hz increments)
USB audio interface Yes
Storage and
Connectivity
Storage Internal Memory
Total maximum size approx. 960 KB (User Song: One Song approx. 250 KB,
Loading Song data from a computer: Up to 10 Songs)
Connectivity
DC IN 16V
Headphones Standard stereo phone jack (x 2)
USB TO HOST Yes
Sound System
Amplifiers 20 W x 2
Speakers 12 cm x 2
Power Supply
AC Adaptor PA-300C (or an equivalent recommended by Yamaha)
Power Consumption 12 W (When using PA-300C AC adaptor)
Auto Power Off Yes
Included Accessories
Owner’s Manual, Quick Operation Guide, 50 Classical Music Masterpieces (Music
Book), Online Member Product Registration, Warranty*,
AC adaptor* (PA-300C or an equivalent), Power cord*, Bench*
* May not be included depending on your area. Check with your Yamaha dealer.
Separately Sold Accessories
(May not be available depending on your area.)
Headphones (HPH-150/HPH-100/HPH-50), Wireless MIDI adaptor (UD-BT01),
AC adaptor (PA-300C or an equivalent recommended by Yamaha)
35
CLP-725 Owner’s Manual
Index
Numerics
50 Preset Songs ...........................................................24
A
AC adaptor .................................................................12
Accessories ....................................................................9
Audio Loopback .........................................................28
Auto Power Off ...........................................................12
B
Backing up Data ..........................................................29
Beat .............................................................................17
Binaural Sampling ......................................................13
C
Computer ...................................................................28
Computer-related Operations .......................................9
D
Damper Pedal .............................................................14
Delete ..........................................................................27
Demo Song List ...........................................................19
Demo Songs ................................................................19
Dual mode ..................................................................22
Duo .............................................................................23
F
Firmware version ........................................................29
G
Grand Expression Modeling ................................ 15, 30
H
Half-pedal ...................................................................14
Headphones ................................................................13
Hz (Hertz) ...................................................................21
I
Initializing ...................................................................29
Intelligent Acoustic Control (IAC) .............................15
K
Key Cover ...................................................................11
L
Left-hand Part .............................................................25
M
Manuals ........................................................................9
Metronome .................................................................17
MIDI Reference ............................................................9
Music Rest ..................................................................11
O
Octave ........................................................................22
Operation Confirmation Sounds ................................16
P
Panel Controls and Terminals ....................................10
Pedals .........................................................................14
Pitch ........................................................................... 21
Playback .....................................................................24
Power ......................................................................... 12
Practice ....................................................................... 25
Preset Songs ...............................................................24
Q
Quick Operation Guide ................................................ 9
Quick Play ..................................................................25
R
Recording ...................................................................26
Reverb ........................................................................20
Reverb Depth .............................................................20
Reverb Type ...............................................................20
Reverb Type List .........................................................20
Right-hand Part ..........................................................25
S
Smart Device ..............................................................28
Smart Device Connection Manual ............................... 9
Smart Pianist ................................................................ 9
Soft Pedal ...................................................................14
Song ...........................................................................24
Sostenuto Pedal ..........................................................14
Speaker .......................................................................13
Stereophonic Optimizer .............................................13
T
Tempo ........................................................................17
Time signature ...........................................................17
Touch Sensitivity ........................................................16
Transpose ...................................................................21
Tuning ........................................................................21
U
USB Audio Interface ..................................................28
USB TO HOST ........................................................... 10
V
Voice .......................................................................... 18
Voice List ...................................................................18
Volume .................................................................10, 17
VRM (Virtual Resonance Modeling) ....................14, 30
(weee_eu_en_02)
(weee_eu_fr_02)
Apache License 2.0
Copyright (c) 2009-2018 Arm Limited. All rights reserved.
SPDX-License-Identifier: Apache-2.0
Licensed under the Apache License, Version 2.0 (the License); you may not use this file except in compliance with the License.
You may obtain a copy of the License at
www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an AS IS BASIS, WITHOUT
WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and limitations under the License.
Modified BSD license
COPYRIGHT(c) 2016 STMicroelectronics
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this
software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Information for users on collection and disposal of old equipment:
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic
products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in
accordance with your national legislation.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative
effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste
disposal service or the point of sale where you purchased the items.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.
Information on Disposal in other Countries outside the European Union:
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local
authorities or dealer and ask for the correct method of disposal.
Informations concernant la collecte et le traitement des déchets d’équipements électriques et électroniques
Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou
électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.
Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et
électroniques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation
nationale.
En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la
sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui
pourraient advenir lors d'un traitement inapproprié des déchets.
Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et
électroniques, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où
vous avez acheté les produits.
Pour les professionnels dans l'Union européenne :
Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques, veuillez contacter votre
vendeur ou fournisseur pour plus d'informations.
Informations sur la mise au rebut dans d'autres pays en dehors de l'Union européenne :
Ce symbole est seulement valable dans l'Union européenne. Si vous souhaitez vous débarrasser de déchets
d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander
la méthode de traitement appropriée.
Important Notice:
U.S. LIMITED WARRANTY for Customers in the United States
For detailed information about this Yamaha product and warranty service, please either
visit the following website address (printable file is available at our website) or contact
Customer Service at the address or telephone number identified below.
Website Address:
Yamaha.io/ClavinovaWarranty
Customer Service:
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620-1273
Telephone: 800-854-1569
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha
ou au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más
cercana o el distribuidor autorizado que se lista debajo.
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario M1S 3R1,
Canada
Tel: +1-416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620,
U.S.A.
Tel: +1-714-522-9011
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9, Col. San José
Insurgentes, Delegación Benito Juárez, México,
D.F., C.P. 03900, México
Tel: +52-55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B –
Vila Olímpia – CEP 04551-010 – São Paulo/SP,
Brazil
Tel: +55-11-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK,
Buenos Aires, Argentina
Tel: +54-11-4119-7000
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Edificio Torre Davivienda, Piso: 20
Avenida Balboa, Marbella, Corregimiento de Bella
Vista, Ciudad de Panamá, Rep. de Panamá
Tel: +507-269-5311
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, U.K.
Tel: +44-1908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
Tel: +49-4101-303-0
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH, Branch
Switzerland in Thalwil
Seestrasse 18a, 8800 Thalwil, Switzerland
Tel: +41-44-3878080
AUSTRIA/CROATIA/
CZECH REPUBLIC
/
HUNGARY/ROMANIA/SLOVAKIA/
SLOVENIA
Yamaha Music Europe GmbH, Branch Austria
Schleiergasse 20, 1100 Wien, Austria
Tel: +43-1-60203900
POLAND
Yamaha Music Europe GmbH
Sp.z o.o. Oddział w Polsce
ul. Wielicka 52, 02-657 Warszawa, Poland
Tel: +48-22-880-08-88
BULGARIA
Dinacord Bulgaria LTD.
Bul.Iskarsko Schose 7 Targowski Zentar Ewropa
1528 Sofia, Bulgaria
Tel: +359-2-978-20-25
MALTA
Olimpus Music Ltd.
Valletta Road, Mosta MST9010, Malta
Tel: +356-2133-2093
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe, Branch Benelux
Clarissenhof 5b, 4133 AB Vianen, The Netherlands
Tel: +31-347-358040
FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d'activités de Pariest,
77183 Croissy-Beaubourg, France
Tel: +33-1-6461-4000
ITALY
Yamaha Music Europe GmbH, Branch Italy
Via Tinelli N.67/69 20855 Gerno di Lesmo (MB),
Italy
Tel: +39-039-9065-1
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal
en España
Ctra. de la Coruña km. 17,200, 28231
Las Rozas de Madrid, Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music House
19th klm. Leof. Lavriou 190 02 Peania – Attiki,
Greece
Tel: +30-210-6686260
SWEDEN
Yamaha Music Europe GmbH Germany filial
Scandinavia
JA Wettergrensgata 1, 400 43 Göteborg, Sweden
Tel: +46-31-89-34-00
DENMARK
Yamaha Music Denmark,
Fillial of Yamaha Music Europe GmbH, Tyskland
Generatorvej 8C, ST. TH., 2860 Søborg, Denmark
Tel: +45-44-92-49-00
FINLAND
F-Musiikki Oy
Antaksentie 4
FI-01510 Vantaa, Finland
Tel: +358 (0)96185111
NORWAY
Yamaha Music Europe GmbH Germany -
Norwegian Branch
Grini Næringspark 1, 1332 Østerås, Norway
Tel: +47-6716-7800
ICELAND
Hljodfaerahusid Ehf.
Sidumula 20
IS-108 Reykjavik, Iceland
Tel: +354-525-5050
CYPRUS
Nakas Music Cyprus Ltd.
Nikis Ave 2k
1086 Nicosia
Tel: + 357-22-511080
Major Music Center
21 Ali Riza Ave. Ortakoy
P.O.Box 475 Lefkoşa, Cyprus
Tel: (392) 227 9213
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, entrance 7, bld. 7, Kievskaya street,
Moscow, 121059, Russia
Tel: +7-495-626-5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
Tel: +49-4101-303-0
Yamaha Music Gulf FZE
JAFZA-16, Office 512, P.O.Box 17328,
Jebel Ali FZE, Dubai, UAE
Tel: +971-4-801-1500
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi
Mor Sumbul Sokak Varyap Meridian Business
1.Blok No:1 113-114-115
Bati Atasehir Istanbul, Turkey
Tel: +90-216-275-7960
ISRAEL
RBX International Co., Ltd.
P.O Box 10245, Petach-Tikva, 49002
Tel: (972) 3-925-6900
OTHER COUNTRIES
Yamaha Music Gulf FZE
JAFZA-16, Office 512, P.O.Box 17328,
Jebel Ali FZE, Dubai, UAE
Tel: +971-4-801-1500
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co., Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: +86-400-051-7700
HONG KONG
Tom Lee Music Co., Ltd.
11/F., Silvercord Tower 1, 30 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel: +852-2737-7688
INDIA
Yamaha Music India Private Limited
P-401, JMD Megapolis, Sector-48, Sohna Road,
Gurugram-122018, Haryana, India
Tel: +91-124-485-3300
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
Yamaha Music Center Bldg. Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: +62-21-520-2577
KOREA
Yamaha Music Korea Ltd.
11F, Prudential Tower, 298, Gangnam-daero,
Gangnam-gu, Seoul, 06253, Korea
Tel: +82-2-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn. Bhd.
No.8, Jalan Perbandaran, Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: +60-3-78030900
SINGAPORE
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: +65-6740-9200
TAIWAN
Yamaha Music & Electronics Taiwan Co., Ltd.
2F., No.1, Yuandong Rd., Banqiao Dist.,
New Taipei City 22063, Taiwan (R.O.C.)
Tel: +886-2-7741-8888
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15, 16th Fl., Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: +66-2215-2622
VIETNAM
Yamaha Music Vietnam Company Limited
15th Floor, Nam A Bank Tower, 201-203 Cach
Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-28-3818-1122
OTHER ASIAN COUNTRIES
https://asia-latinamerica-mea.yamaha.com/
index.html
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 80 Market Street, South Melbourne,
VIC 3205 Australia
Tel: +61-3-9693-5111
NEW ZEALAND
Music Works LTD
P.O.BOX 6246 Wellesley, Auckland 4680,
New Zealand
Tel: +64-9-634-0099
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
https://asia-latinamerica-mea.yamaha.com/
index.html
NORTH AMERICA
CENTRAL & SOUTH AMERICA
EUROPE
AFRICA
MIDDLE EAST
ASIA
OCEANIA
DMI27
Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan
(For European Countries) Importer: Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany
Manual Development Group
© 2020 Yamaha Corporation
Published 02/2020 MWMA*.*-**A0
VCR9660
https://www.yamaha.com/
Yamaha Global Site
https://download.yamaha.com/
Yamaha Downloads
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Yamaha CLP-725 El manual del propietario

Categoría
Equipo de música suplementario
Tipo
El manual del propietario