Cap A Tread 016A71507 Guía de instalación

Marca
Cap A Tread
Modelo
016A71507
Tipo
Guía de instalación
1. Gather all of tools listed.
2. Start by removing any existing carpet, pad and staples from your existing staircase.
3. Vacuum the staircase and make sure it’s free of debris.
1. Reúna todas las herramientas indicadas.
2. Comience por quitar cualquier alfombra, almohadilla y grapa que exista en su escalera.
3. Pase la aspiradora en la escalera y asegúrese de que esté libre de escombros.
4. Measure each stair tread (step). Be sure to measure twice and from both sides of
the tread AS WELL AS use a T-Bevel or Angle Gauge since they may not be the
same size and might not be square.
a) Cut down the width of the Cap A Tread with a sliding compound miter saw.
b) Use a table saw (or circular saw with a guide) to make any alterations to the depth
of the Cap A Tread that run along the entire length of the product.
4. Mida cada peldaño (escalón). Asegúrese de medir dos veces y desde ambos lados del peldaño,
ASÍ COMO de utilizar una escuadra o medidor de ángulo dado que es posible que no sean
del mismo tamaño y no sean cuadrados.
a) Recorte el ancho del Cap A Tread con una sierra ingleteadota compuesta deslizante.
b) Utilice una sierra de mesa (o sierra circular con una guía) para modificar la profundidad
del Cap A Tread que se extiende a lo largo de todo el producto.
www.capatread.com
• The flat non-nosing portion of Cap A Tread is 8mm (5/16”) thick
• Works with treads up to 1" thick
• The flat non-nosing portion of Cap A Tread is 8mm (5/16") thick
• Works with treads between 1-1/8" to 1-3/4" Thick
• Tread can either cap the existing tread (for treads 1-1/8" to 1-1/2" thick) or butt flush
to the front of the existing tread face (for treads 1-9/16" to 1-3/4" thick)
• MAX PROTRUSION IS 11/16" OVERHANG. Anything more than that and the riser
must be built out using 1"x 6" boards before Cap A Tread riser is installed
• La parte plana sin arista del Cap A Tread tiene un espesor de 8 mm (5/16")
• Sirve para peldaños con un espesor entre 1-1/8" y 1-3/4"
• El peldaño puede tapar el peldaño existente (para peldaños de 1-1/8" a 1-1/2" de espesor)
o bien estar adyacente a la parte frontal de la cara del peldaño existente
(para peldaños de 1-9/16" a 1-3/4" de espesor)
•
LA PROTUBERANCIA SALIENTE MÁXIMA ES DE 11/16". Cualquier medida mayor y la contrahuella
se deben construir con tablas de 1" x 6" antes de instalar la contrahuella del Cap A Tread
• La parte plana sin arista del Cap A Tread tiene un espesor de 8 mm (5/16")
• Sirve para peldaños de hasta 1" de espesor
Cap-A-Tread Dimensions
STANDARD
TYPE 2
ESTÁNDAR
TIPO 2
Dimensiones del Cap-A-Tread
Required Tools and Materials
Herramientas y Materiales Requeridos
Basic Installation Instructions
Instrucciones básicas de instalación
Adhesivo para construcción
a base de uretano
Urethane-based
construction
adhesive
Aspiradora
Vacuum
Cinta para medir
Tape measure
Gafas de seguridad
Safety glasses
Guantes
Gloves
Sierra de mesa con punta de
carburo de cuchillas o vio la mano
Table saw with
carbide-tipped blades
or hand saw
Mitre vio con punta de
carburo de cuchillas
Miter saw with
carbide-tipped
blades
Martillo
Hammer
Raspador
Scraper
NOTE: Cap-A-Tread should be installed from bottom stair to top with treads
and risers being installed in the alternating order.
NOTA: El Cap-A-Tread se debe instalar desde el inferior de la escalera hacia la parte superior,
al mismo tiempo que se instalan los peldaños y las contrahuellas de forma alternativa.
Update carpeted or worn-out stairs
Laminate & Vinyl
Stair Renewal System
Actualice escaleras alfombradas o desgastadas
• Un fácil de instalar, escalera durable cubre con attached
husmeando para la actualización de huellas y contrahuellas
• Coordinar con su escalera de acceso a la compra de suelo
laminado o vinilo
• Instalación sencilla con pegamento
• Una manera rentable de agregar valor a su vivienda
Laminado y vinilo sistema
de renovación de escaleras
(limited residential warranty)
(garantía residencial limitada)
DE GARANTÍA
AÑOS
• An easy to install, durable stair covering with a
pre-attached nosing for updating treads and risers
• Coordinate to your staircase to a laminate
or vinyl flooring purchase
• Easy glue-down installation
• Cost-effective way to add value to your home
1-11/16"
15/16"
1-1/8"
11-13/16"
12-1/8"
2-3/16"
15/16"
1/4"
If the tread is thicker than
1-1/2" this portion will
rest flush against the face
of the tread.
Si el peldaño tiene un grosor
superior a 1-1/2", esta parte
estará alineada contra la cara
del peldaño.
1-5/8"
12-1/8"
11-7/16"
TREAD (ESCALÓN) RISER (CONTRAHUELLA)
PREPARE / PREPARAR
MEASURE
MEDIR
Cap-A-Tread_Insert_Slip_11X17_Final_A_1_13_14.pdf 1 1/13/14 11:37 AM
Specs for
Landings and Top Stair
**Be sure to only use Zamma coordinating Stairnose molding at the top stair.
There are 2 different options to use for the top stair or landing.
1. For landings, you can use a coordinating Stairnose molding. OR
2. Use Cap A Tread. Rip at the same width but no less than 4" as your flooring plank
from bullnose and join to flooring on landing with T-Molding or Multi-Purpose Reducer.
Some notching may be required depending upon your staircase.
If a bullnose exists on landing, ONLY Cap A Tread with adjoining threshold
should be used. Any existing bullnose should not be ripped off.
6. Use Heavy Duty Liquid Nail or any All Urethane Construction Adhesive. Apply about an
1/4" thick bead around the perimeter and then throughout the middle in a zig-zag shape on
the back of the tread as seen below and adhere the new Cap A Tread to the existing tread.
No need to use a trowel or full spread the adhesive.
IMPORTANT. TO KEEP TREADS IN PLACE WHILE INSTALLING FROM TOP TO BOTTOM,
YOU CAN ALSO SECURE WITH 3-4 BRAD NAILS ACROSS THE WIDTH OF THE TREAD,
BUT NOT MORE THAN 1/4" FROM THE CURRENT RISER. YOU WANT THE CAP A
TREAD RISER TO COVER UP ANY BRAD NAILS INSTALLED.
7. Measure for risers only after the tread has been installed.
a) Cut down the width of risers with a sliding compound miter saw.
b) Use a table saw (or circular saw with a guide) to make any alterations to the height of the riser that runs along the entire length of the product.
8. As in step #6, use Heavy Duty Liquid Nail or any construction urethane adhesive. Apply about an 1/4" thick bead around the perimeter and
then throughout the middle in a zig-zag shape on the back of the riser as previously shown and adhere the Cap A Tread to the existing tread.
7. Mida las contrahuellas una vez que se haya instalado el peldaño.
a) Recorte el ancho de las contrahuellas con una sierra ingleteadota compuesta deslizante.
b) Utilice una sierra de mesa (o sierra circular con una guía) para modificar la altura de la contrahuella que se extiende a lo largo de todo el producto.
8. Al igual que el paso Nº 6, utilice un pegamento pesado o cualquier adhesivo para construcción de uretano. Aplique una línea gruesa de
aproximadamente 1/4" alrededor del perímetro y luego en todo el centro en forma de zig-zag en la parte posterior de la contrahuella, como se muestra
más arriba, y adhiera el Cap a Tread al peldaño existente.
9. Caulk Cap A Tread around the perimeter
of the stair treads / risers and wipe clean
for a nice finished look with no gaps.
9. Calafetee un Cap A Tread alrededor del
perímetro de los peldaños/contrahuellas y limpie
para obtener un bonito acabado sin fisuras.
6. Utilice un pegamento pesado o cualquier adhesivo para construcción de uretano. Aplique una línea espesa de aproximadamente 1/4" alrededor del perímetro y
luego a través de todo el centro en forma de zig-zag en la parte posterior del peldaño, como se muestra a continuación, y adhiera el nuevo Cap A Tread al peldaño
existente. No es necesario utilizar una paleta ni esparcir el adhesivo por completo. IMPORTANTE: PARA MANTENER LOS PELDAÑOS EN SU LUGAR MIENTRAS
REALIZA LA INSTALACIÓN DESDE LA PARTE SUPERIOR HACIA LA INFERIOR, TAMBIÉN PUEDE FIJARLOS CON 3 Ó 4 CLAVOS DE TERMINACIÓN A LO LARGO
DEL ANCHO DEL PELDAÑO, PERO A NO MÁS DE 1/4" DE LA CONTRAHUELLA ACTUAL. ASEGÚRESE DE QUE LA CONTRAHUELLA DEL CAP A TREAD CUBRA
TODOS LOS CLAVOS DE TERMINACIÓN INSTALADOS.
Molding Overhang on Both Sides
• If overhang occurs on both sides of stringers, one side of overhang will need to be
ripped off with an appropriate saw.
• Keep any remaining overhang and re-install it with brad nails / glue. Caulk the seams
as best as possible. Re-painting may be required.
Cap-A-Tread Videos to Reference
Go to these YouTube links for further detailed installation
Standard Cap A Tread Installation
http://www.youtube.com/watch?v=Us8Ga7_MYUI
Type 2 Cap A Tread and specific details
http://www.youtube.com/watch?v=90tpUA3nttc
Do I Remove Existing Spindles / Install New Spindles
Pre-Attached to Treads?
• Staircases can both have / not have spindles and the
spindles may or may not be pre-attached to existing
stair treads.
• If spindles are pre-attached to existing stair treads,
these need to be removed prior to installation of
Cap A Tread and re-installed after the Cap A Tread
installation is complete.
** Be sure to consult a Professional Finished
Carpenter prior to installation or hire a Professional
Finished Carpenter to properly complete this task.
• DO NOT CUT AROUND EXISTING SPINDLES TO
INSTALL CAP A TREAD!
FAQ’s (Continued)
Landings that turn a corner
• For landings that turn a corner, use a piece
from the length of a tread already ripped
off and glue it underneath so no
gap is exposed.
Why does the return not come pre-mitered?
• Since most walls are not square, pre-mitering
the return could mean it may not properly fit
properly onto the side profile of the tread.
Use a T-Bevel or Angle Gauge to properly
determine the angle needed to cut the return.
How do I install the return?
• Secure with 3-4 brad nails and a small
amount of glue.
How do I finish off the return
on the side, or side of a riser?
• Miter a cut off piece of return
to fit into place and secure
with brad nails / glue.
Risers Over 8-1/4" Tall
• If your riser is over 8-1/4" tall, the standard Cap A Tread coordinating riseris likely not tall
enough to cover up the existing riser once the Cap A Tread on top is installed and you
will need to proceed one of two ways.
• Coordinating Risers: An extra Cap A Tread should be ordered. Once received, rip off the
nosing, cut down to size and use as a riser.
• White Risers: Purchase a piece of 12" x 48" white melamine to cut down and use as a riser.
If no existing nosing exists, can I still install Cap A Tread
• Yes, a gap can exist with waterfall stairs as when you walk
up a staircase, your feet do not apply diagonal pressure.
www.capatread.com
FINISHING /
ACABADO
RIP OFF AT MINIMUM 4"
FROM NOSING
Basic Installation Instructions
Instrucciones básicas de instalación
FAQ's
5. Check the cut of the Cap A Tread for
accuracy by dry-fitting it onto the stair
for which you measured.
5. Revise que el corte del Cap A Tread sea
preciso, colocándolo en seco en la escalera
de la que ha tomado la medida.
Installation Links
SET IN PLACE / INSTALAR
CHECK FIT
REVISAR EL AJUSTE
Adhesive Pattern /
Patrón de adhesivo
RISERS
CONTRAHUELLAS
Dog Ears
• Dog ears are necessary when the standard Cap A Tread with a return, has too much
of a pre-existing miter to use.
• Miter the tread to the necessary depth / angle yourself.
• Miter a piece already cut off the tread to finish off the installation.
Cap-A-Tread_Insert_Slip_11X17_Final_A_1_13_14.pdf 2 1/13/14 11:37 AM
  • Page 1 1
  • Page 2 2

Cap A Tread 016A71507 Guía de instalación

Marca
Cap A Tread
Modelo
016A71507
Tipo
Guía de instalación
Descargar PDF
informe

En otros idiomas

Documentos relacionados

Otros documentos