Homelite ut906800 El manual del propietario

Marca: Homelite

Modelo: ut906800

Categoría: Generadores de poder

Tipo: El manual del propietario

00:00

120V AC

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your generator has been engineered and manufactured to our high standard for dependability, ease of operation, and op-

erator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product. If you do not understand the warnings and instructions in the operator’s manual, do not use this product.

Thank you for your purchase.

Ce générateur a été conçu et fabriqué conformément à nos

strictes normes de fiabilité, de simplicité d’emploi et de sécurité

d’utilisation. Correctement entretenu, il vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre

le manuel d’utilisation avant d’employer ce produit. Si tous

les avertissements et toutes les consignes de sécurités et

instructions du manuel d’utilisation ne sont pas bien compris,

ne pas utiliser ce produit.

Merci de votre achat.

Su generador ha sido diseñado y fabricado de conformidad con

estrictas normas para brindar fiabilidad, facilidad de uso y seguridad

para el operador. Con el debido cuidado, le brindará muchos años

de sólido y eficiente funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto. Guarde este manual del operador y

estúdielo frecuentemente para lograr un funcionamiento seguro

y continuo de este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

OPERATOR’S MANUAL

Manuel d’utilisation

Manual del operador

6800 WATT GENERATOR

Générateur de 6800 watts

Generador 6800 watts

UT906800

Series / Série / Serie

NEUTRAL BONDED TO FRAME

(CONNECTEUR NEUTRE RELIÉ AU CADRE,

PUNTO NEUTRO CONECTADO AL MARCO)

To register your Homelite product, please

visit: http://register.homelite.com/

Pour enregistrer votre produit de Homelite,

s’il vous plaît la visite:

http://register.homelite.com/

Para registrar su producto de Homelite, por

favor visita: http://register.homelite.com/

NOTICE AVIS AVISO

Do not use E15 or E85 fuel (or fuel

containing greater than 10% etha-

nol) in this product. It is a violation

of federal law and will damage the unit and void your warranty.

Ne pas utiliser d’essence E15 ou E85 (ou un carburant

contenant plus de 10 % d’éthanol) dans ce produit. Une

telle utilisation représente une violation de la loi fédérale et

endommagera l’appareil et annulera la garantie.

No utilice combustibles E15 o E85 (ni combustibles que

contengan más de 10 % de etanol) con este producto. Esto

constituye una violación a la ley federal, dañará la unidad

y anulará la garantía.

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner

toutes les figures mentionnées dans le manuel

d’utilisation.

Consulte esta sección desplegable para ver todas

las figuras a las que se hace referencia en el

manual del operador.

iii

00:00

120V AC

Fig. 1

J - Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

K - Engine switch with lock button (commutateur

de moteur avec bouton de verrouillage,

interruptor del motor con botón del seguro)

L - Multifunctional display (numérique

multifonctionnel, pantalla multifuncional)

- Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

N - Air filter (filtre à air, filtro de aire)

O - Choke (volet de départ, anegador)

P - Ground terminal (borne de terre, terminal de

conexión a tierra)

Q - Fuel tank vapor vent (évent de vapeur du

réservoir de carburant, respirador del vapor

del tanque de combustible)

R - Muffler (silencieux, silenciador)

S - Spark arrestor screen (écran du pare-

étincelles)

T - Cord retainers (retenues de cordon, retén

para el cordón)

U - Low oil shut-off indicator (indicateur de bas

niveau d’huile, indicador de apagado por

poco aceite)

A - Handle lock pin (goupille de blocage de la

poignée, pasador de seguro del mango)

B - Fuel cap (bouchon de carburant, tapa del

tanque)

C - Fuel tank (réservoir de carburant, tanque de

combustible)

D - 120 volt AC 20 amp receptacles (prises 120 V

c.a. 20 A, 120 V de CA 20 A receptáculos)

E - 120 volt AC 20 amp circuit breaker

(disjoncteur de 120V c.a. 20 A, disyuntor de

circuito de 120 V de CA 20 A)

F - 240 volt AC 30 amp receptacle (prise 240 V

c.a. 30 A, 240 V de CA 30 A receptáculo)

G - 240 volt AC 30 amp circuit breaker(disjoncteur

de 240 V c.a. 30 A, disyuntor de circuito de

240 V de CA 30 A)

H - Battery (pile, batería)

I - Oil cap/dipstick (bouchon/jauge d’huile, tapa

de relleno de aceite/varilla medidora de aceite)

Fig. 2

Fig. 3

A - Socket wrench (clé à douille, llave de

casquillo)

B - Adjustable wrench (clé a molette, llave

ajustable)

C - Phillips screwdriver (tournevis cruciforme,

destornillador Phillips)

YAMAHA

OFF

00:00

120V AC

ENGINE SWITCH

Fig. 4

A - Bolt (boulon, perno)

B - Frame (cadre, armazón)

C - Washer (rondelle, arandela)

D - Frame support with foot (support de cadre

avec pied, soporte del armazón con pie)

E - Flange nut (écrou à épaulement, tuerca de

brida)

F - Lock nut (écrou de blocage, tuerca de

seguridad

G - Rubber foot (patin en caoutchouc, pie de

goma)

Fig. 7

A - Handle (poignée, mango)

B - Bolt (boulon, perno)

C - Spacer (entretoise, espaciador)

D - Washer (rondelle, arandela)

E - Lock nut (écrou frein, tuerca de bloqueo)

Fig. 6

A - Lanyard (bracelet, correa)

B - Handle lock pin (goupille de blocage de la

poignée, pasador de seguro del mango)

C - Frame (cadre, pasador de seguro del mango)

Fig. 8

A - Lanyard (bracelet, correa)

B - Hole (trou, agujero)

C - Handle (poignée, mango)

D - Handle lock pin (goupille de blocage de la

poignée, pasador de seguro del mango)

Fig. 10

Fig. 9

A - Oil cap/dipstick (bouchon/jauge d’huile,

tapa de relleno de aceite/varilla medidora de

aceite)

B - Oil fill hole (orifice de remplissage d’huile,

agujero de llenado de aceite)

Fig. 11

A - Engine switch (commutateur de moteur,

interruptor del motor)

B - Fuel cap (bouchon de carburant, tapa del

tanque de combustible)

C - Fuel tank (réservoir de carburant, tanque de

combustible)

- Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

E - Lock button (bouton de verrouillage, botón

del seguro)

Fig. 12

A - Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

B - Fuel valve (robinet de carburant, válvula de

combustible)

C - Off (arret, apagado)

D - On (marche, encendido)

OFF

START

ENGIN E SW.

CIR CUIT PROTECTO R

OFF

120V AC/CA

120V/240 AC/CA

NEUTRAL FLOATING

NEUTRAL FLOTAS

Cor d

Ret aine r

Cor d

Ret aine r

00:00

A - Positive (+) terminal [borne positive (+), tapa

del terminal positiva (+)]

B - Red wire (+) [fil rouge (+), cable rojo (+)]

C - Negative (–) terminal [borne négative (–),

terminal negativa (–)]

D - Black wire (–) [fil noir (–), cable negro (–)]

Fig. 5

A - Lock nut (écrou frein, tuerca de bloqueo)

B - U-bracket (support en U, soporte en “U”)

C - Washer (rondelle, arandela)

D - Wheel (roué, rueda)

E - Wheel spacer (écarteur de roué, espaciador

de rueda)

F - Bolt (boulon, perno)

OFF

A - Spark plug (bougie, bujía)

B - Spark plug cap (capuchon de bougie, tapa de

la bujía)

Fig. 18

Fig. 17

Fig. 13

A - Move choke lever left to run (pousser gauche

le levier d’étranglement pour la marche,

desplace izquierda la palanca del anegador

para poner en marcha)

B - Move choke lever right to start (tirer droite

le levier d’étranglement pour démarrer,

desplace derecha de la palanca del anegador

para arrancar)

A - Screws (vis, tornillos)

B - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

C - Filter element (élément du filtre, elemento de

filtro)

D - Air filter unit (unité de filtre à air, unidad del

filtro de aire)

Fig. 16

A - Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

B - Oil cap/dipstick (bouchon/ jauge d’huile,

tapa de relleno de aceite/varilla medidora de

aceite)

OFF

A - Carburetor drain screw (vis de vidange

du carburateur, tornillo de drenaje del

carburador)

A - Fuel line (conduites de carburant, conducto

de combustible)

B - Fuel filter (filtre à carburant, filtro de

combustible)

Fig. 20

Fig. 21

Fig. 15

A - Fuel line (conduite de carburant, conducto

de combustible)

B - Petcock (petit robinet, llave de purga)

C - Fuel valve (robinet de carburant, válvula de

combustible)

A B

Fig. 19

Fig. 14

A - Engine switch (contacteur du moteur,

interruptor del motor)

B - Off (arret, apagado)

C - Start (démarrage, arranque)

D - Lock button (bouton de verrouillage, botón

del seguro)

Page 2 — English



Introduction .................................................................................................................................................................... 2



Important Safety Instructions .....................................................................................................................................3-4



Specific Safety Rules ..................................................................................................................................................... 4



Symbols ......................................................................................................................................................................5-7



Electrical .....................................................................................................................................................................8-9



Features ...................................................................................................................................................................... 10



Assembly ................................................................................................................................................................11-12



Operation ................................................................................................................................................................13-15



Maintenance ...........................................................................................................................................................15-18



Troubleshooting ........................................................................................................................................................... 19



Warranty ..................................................................................................................................................................20-22



Parts Ordering / Service..................................................................................................................................Back Page

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product, making it easy to maintain and operate.

DANGER:

GROUNDING THE GENERATOR

To reduce the risk of shock or electrocution, generator must be properly ground-

ed. The nut and ground terminal on the frame must always be used to connect

the generator to a suitable ground source. The ground path should be made with

#8 size wire. Connect the terminal of the ground wire between the lock washer

and the nut, and tighten the nut fully. Connect the other end of the wire securely

to a suitable ground source.

The National Electric Code contains several practical ways in which to establish

a good ground source. If a steel or iron rod is used, it should be at least 5/8 in.

diameter, and if a nonferrous rod is used, it should be at least 1/2 in. diameter

and be listed as material for grounding. Drive the rod or pipe to a depth of 8 ft. If a

rock bottom is encountered less than 4 ft. down, bury the rod or pipe in a trench.

All electrical tools and appliances operated from this generator must be properly

grounded by use of a third wire or be “Double Insulated.”

It is recommended to:

1. Use electrical devices with 3-prong grounded plugs.

2. Use an extension cord intended for outdoor use with a 3-pole receptacle and a 3-prong plug at opposite ends to

ensure continuity of the ground protection from the generator to the appliance.

Check and adhere to all applicable federal, state, and local regulations relating to grounding specifications. Consult a

qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as

to whether the generator is properly grounded.

TABLE OF CONTENTS

INTRODUCTION

00:00

120V AC

Page 3 — English

IMPORTANT SAFETY INSTRUCTIONS

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

 Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

 ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See

a doctor. You could have carbon monoxide poisoning.

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below could result in electrocution,

fire, and/or carbon monoxide poisoning, which can cause

death or serious injury.

DANGER:

National Electric Code requires generator to be grounded

to an approved earth ground. Before using the ground ter-

minal, consult a qualified electrician, electrical inspector,

or local agency having jurisdiction for local codes or or-

dinances that apply to the intended use of the generator.

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be

followed during installation and maintenance of the genera-

tor and batteries.

 Do not connect to a building’s electrical system unless

the generator and transfer switch have been properly

installed and the electrical output has been verified by

a qualified electrician. The connection must isolate the

generator power from utility power and must comply with

all applicable laws and electrical codes.

 Do not allow children or untrained individuals to use this

unit.

 Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness

or death.

 Keep all bystanders, children, and pets at least 10 feet

away.

 Wear sturdy and dry shoes or boots. Do not operate while

barefoot.

 Do not operate generator when you are tired or under the

influence of drugs, alcohol, or medication.

 Keep all parts of your body away from any moving parts

and all hot surfaces of the unit.

 Do not touch bare wire or receptacles.

 Do not use generator with electrical cords which are

worn, frayed, bare, or otherwise damaged.

 Before storing, allow the engine to cool and drain fuel

from the unit.

 Do not operate or store the generator in rain, snow, or

wet weather.

 Store the generator in a well-ventilated area with the fuel

tank empty. Fuel should not be stored near the generator.

 Empty fuel tank, close fuel valve, and restrain the unit

from moving before transporting in a vehicle.

 Allow engine to cool for five minutes before refueling.

 To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

 Do not smoke while handling fuel.

 Store fuel in a container approved for gasoline.

 Position the unit on level ground, stop engine, and allow

to cool before refueling.

 Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

 Tighten the fuel cap securely after refueling.

 Wipe spilled fuel from the unit.

 Never attempt to burn off spilled fuel under any circum-

stances.

 Generators vibrate in normal use. During and after the

use of the generator, inspect the generator as well as

extension cords and power supply cords connected to

it for damage resulting from vibration. Have damaged

items repaired or replaced as necessary. Do not use plugs

or cords that show signs of damage such as broken or

cracked insulation or damaged blades.

 For power outages, permanently installed stationary gen-

erators are better suited for providing back-up power to

the home. Even a properly connected portable generator

can become overloaded. This may result in overheating

or stressing the generator components, possibly leading

to generator failure.

Page 4 — English

IMPORTANT SAFETY INSTRUCTIONS

SPECIFIC SAFETY RULES

 Use only authorized replacement parts and accessories

and follow instructions in the Maintenance section of this

manual. Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of shock or

injury.

 Maintain the unit per maintenance instructions in this

Operator’s Manual.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.

WARNING:

When this generator is used to supply a building

wiring system: generator must be installed by a quali-

fied electrician and connected to a transfer switch as

a separately derived system in accordance with NFPA

70, National Electrical Code. The generator shall be

connected through a transfer switch that switches all

conductors other than the equipment grounding con-

ductor. The frame of the generator shall be connected to

an approved grounding electrode. Failure to isolate the

generator from power utility can result in death or injury

to electric utility workers.

 Do not use this generator to provide power for emergency

medical equipment or life support devices.

 This generator has a neutral bonded condition. This

means the neutral conductor is electrically connected to

the frame of the machine.



Exhaust contains poisonous carbon monoxide, a color-

less, odorless gas. Breathing exhaust can cause loss

of consciousness and can lead to death. If running in a

confined or partially-enclosed area, the air may contain

a dangerous amount of carbon monoxide. To keep ex-

haust fumes from building up, always provide adequate

ventilation.



Always use a battery-powered carbon monoxide detec-

tor when running the generator. If you begin to feel sick,

dizzy, or weak while using the generator, shut it off and

get to fresh air immediately. See a doctor. You may have

carbon monoxide poisoning.



Place the generator on a flat, stable surface with a slope

of no more than 4°.



Operate in a well-ventilated, well-lit area isolated from

working areas to avoid noise interference.



Operating the generator in wet conditions could result in

electrocution. Keep the unit dry.



Keep the generator a minimum of 3 feet away from all

types of combustible material.



Do not operate generator near hazardous material.



Do not operate generator at a gas or natural gas filling

station.



Do not touch the muffler or cylinder during or immedi-

ately after use; they are HOT and will cause burn injury.



Do not allow the generator’s gas tank to overflow when

filling. Fill to 1 in. below the top neck of the gasoline tank

to allow for fuel expansion. Do not cover the fuel tank

cap when the engine is running. Covering the fuel tank

cap during use may cause engine failure and/or damage

to the tool.



Do not smoke when filling the generator with gasoline.



Shut down the engine and allow to cool completely be-

fore adding gasoline or lubricant to the generator.



Do not remove the oil dipstick or the fuel tank cap when

the engine is running.



Pay close attention to all safety labels located on the

generator.



Keep children a minimum of 10 feet away from the gen-

erator at all times.



The unit operates best in temperatures between 23°F

and 104°F with a relative humidity of 90% or less.



Operating voltage and frequency requirement of all

electronic equipment should be checked prior to plug-

ging them into this generator. Damage may result if the

equipment is not designed to operate within a +/- 10%

voltage variation, and +/- 3 hz frequency variation from

the generator name plate ratings. To avoid damage, al-

ways have an additional load plugged into the generator

if solid state equipment (such as a television set) is used.

A power line conditioner is recommended for some solid

state applications.

 When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys, nails,

screws, or other small metal objects that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.



For outdoor use only.



Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you loan

someone this product, loan them these instructions also.

Page 5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Electric Shock

Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Toxic Fumes

Running generator gives off carbon monoxide, an odorless, color-

less, poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

Fire/Explosion

Fuel and its vapors are extremely flammable and explosive. Fire

or explosion can cause severe burns or death.

Hot Surface

To reduce the risk of injury or damage, avoid contact with any

hot surface.

Lifting Hazard

To reduce the risk of serious injury, avoid attempting to lift the

generator alone.

Ground

Consult with local electrician to determine grounding requirements

before operation.

Electrocution

Failure to properly ground generator can result in electrocution,

especially if the generator is equipped with a wheel kit.

Recycle Symbol

This product uses lead acid (Pb) batteries. Local, state or federal

laws may prohibit disposal of batteries in ordinary trash. Consult

your local waste authority for information regarding available re-

cycling and/or disposal options.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

Page 6 — English

SYMBOLS

SAFETY LABELS

The information below can be found on the generator. For your safety, please study and understand all of the labels before

starting the generator.

If any of the labels come off the unit or become hard to read, contact an authorized service center for replacement.

 You WILL be KILLED or SERIOUSLY HURT if you do not

follow the Operator’s Manual instructions.

 Risk of Fire. Do not add fuel while the product is operat-

ing.

 Generator is a potential source of electric shock. Do not

expose to moisture, rain, or snow. Do not operate with

wet hands or feet.

 Exhaust contains poisonous carbon monoxide gas that

can cause unconsciousness or DEATH. Operate in well-

ventilated, outdoor areas away from open windows or

doors.

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

gal Gallon Volume

qt Quart Volume

DANGER

PELIGRO

L’utilisation d’une génératrice à l’intérieur PEUT VOUS TUER ENQUELQUES MINUTES.

Les génératrices produisent du monoxyde de carbone, un gaz mortel incolore et inodore.

NE JAMAIS utiliser à l’intérieur d’une maison ou d’un garage,MÊME SI les portes et

les fenêtres sont ouvertes.

Utiliser uniquement À L’EXTÉRIEUR et loin des fenêtres, des portes et des évents.

Usar un generador en el interior PUEDE MATARLO EN POCOS MINUTOS.

Los gases de escape del generador contienen monóxido de carbono. Es un veneno

que no puede verse ni olerse.

NUNCA lo use dentro de su hogar o del garaje, INCLUSO con las puertas y las

ventanas abiertas.

Sólo utilícelo AL AIRE LIBRE y lejos de ventanas, puertas y respiraderos.

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

 Failure to properly ground generator can result in elec-

trocution, especially if the generator is equipped with a

wheel kit.

 Do not expose to rain or use in damp locations.

 Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

 NEVER use inside a home or garage, EVEN IF doors and

windows are open.

 Only use OUTSIDE and far away from windows, doors,

and vents.

Page 7 — English

SYMBOLS

FUEL WARNING

No smoking when filling with gasoline. Do not overfill. Full

level is 1 in. below the top of the fuel neck. Stop the engine

for five minutes before refueling to avoid the heat from the

muffler igniting fuel vapors.

940513001-04

Product does not include ground rod or copper wire. National Electric Code requires generator to be

properly grounded to an approved earth ground. Call an electrician for local grounding requirements.

Le produit ne comprend pas de piquet de terre ou de fil en cuivre. Le code electrique americain

(National Electric Code) requiert un générateur pour une bonne mise à la terre approuvée. Appeler un

électricien pour connaître les exigences locales de mise à la terre.

El producto no incluye el ealambre de cobre ni la barra de conexión a tierra. Los Reglamentos

Nacionales de Electricidad exigen que el generador esté debidamente conectado a una tierra aprobada.

Comuniquese con un electrista para todo lo relacionado con los requistos de conexión a tierra.

CHECK LUBRICANT

940708019-03

DANGERDANGER PELIGRO

940974089-02

Risk of Fire. Keep all objects at least 3 feet away from this machine. Heat from Muffler and Exhaust gases

can ignite combustible objects.

Risque d’incendie. Éloigner tous les objets au moins de 91,4 cm (3 pi) de cet appareil. La chaleur

du pot d’échappement et les gaz d’échappement peuvent enflammer les objets combustibles.

Riesgo de incendio. Mantener todos los objetos a una distancia mínima de 91,4 cm (3 pies) de esta

máquina. El calor de los gases del silenciador y el escape pueden prender fuego a objetos combustibles.

GROUNDING WARNING

National Electric Code requires generator to be grounded

to an approved earth ground.

ENGINE LUBRICANT WARNING

You must add lubricant before first operating the generator.

Always check the lubricant level before each operation. The

lubricant level should always register between the hatched

areas on the dipstick. The unit is equipped with a sensor

which will automatically shut off the engine if the lubricant

level falls below a safe limit.

HOT SURFACE WARNING

Do not touch the muffler or aluminum cylinder of the engine.

They are very HOT and will cause severe burns. Don’t put

any flammable or combustible materials in the direct path

of the exhaust.

CLEARANCE WARNING

While operating and storing, keep at least 3 feet of clearance

on all sides of this product, including overhead. Allow a mini-

mum of 30 minutes of “cool down” time before storage. Heat

created by muffler and exhaust gases could be hot enough

to cause serious burns and/or ignite combustible objects.

SPARK ARRESTOR

Operation of this equipment may create sparks that can

start fires around dry vegetation. A spark arrestor may be

required. The operator should contact local fire agencies for

laws or regulations relating to fire prevention requirements.

Page 8 — English

ELECTRICAL

ELECTRIC MOTOR LOADS

It is characteristic of common electric motors in normal operation to draw up to six times their running current while starting.

This table may be used to estimate the watts required to start electric motors; however, if an electric motor fails to start or

reach running speed, turn off the appliance or tool immediately to avoid equipment damage. Always check the requirements

of the tool or appliance being used compared to the rated output of the generator.

Motor Size (H.P.) Running Watts

Watts Required to Start Motor

Universal Capacitor Split Phase

1/8 275 N/A 850 1200

1/6 275 600 850 2050

1/4 400 800 1050 2400

1/3 450 950 1350 2700

1/2 600 1000 1800 3600

3/4 850 1200 2600 —

1 1100 N/A 3300 —

GENERATOR CAPACITY

Make sure the generator can supply enough continuous (run-

ning) and surge (starting) watts for the items you will power

at the same time. Follow these simple steps.

1. Selecttheitemsyouwillpoweratthesametime.

2. Totalthecontinuous(running)wattsoftheseitems.This

is the amount of power the generator must produce to

keep the items running. See the wattage reference chart

at right.

3. Estimatehowmanysurge(starting)wattsyouwillneed.

Surge wattage is the short burst of power needed to

start electric motor-driven tools or appliances such as a

circular saw or refrigerator. Because not all motors start

at the same time, total surge watts can be estimated by

adding only the item(s) with the highest additional surge

watts to the total rated watts from step 2.

NOTICE:

Operating voltage and frequency requirement of all

electronic equipment should be checked prior to plug-

ging them into this generator. Damage may result if the

equipment is not designed to operate within a +/- 10%

voltage variation, and +/- 3 hz frequency variation from

the generator name plate ratings. To avoid damage, al-

ways have an additional load plugged into the generator

if solid state equipment (such as a television set) is used.

A power line conditioner is recommended for some solid

state applications.

EXTENSION CORD CABLE SIZE

Refer to the table below to ensure the cable size of the extension cords you use are capable of carrying the required load.

Inadequate size cables can cause a voltage drop, which can burn out the appliance and overheat the cord.

Current in

Amperes

Load in Watts Maximum Allowable Cord Length

At 120V At 240V #8 Wire #10 Wire #12 Wire #14 Wire #16 Wire

2.5 300 600 1000 ft. 600 ft. 375 ft. 250 ft.

5 600 1200 500 ft. 300 ft. 200 ft. 125 ft.

7.5 900 1800 350 ft. 200 ft. 125 ft. 100 ft.

10 1200 2400 250 ft. 150 ft. 100 ft. 50 ft.

15 1800 3600 150 ft. 100 ft. 65 ft.

20 2400 4800 175 ft. 125 ft. 75 ft.

25 3000 6000 150 ft. 100 ft.

30 3600 7200 125 ft. 65 ft.

40 4800 9600 90 ft.

Page 9 — English

NOTICE:

Do not overload the generator’s capacity. Exceeding the

generator’s wattage/amperage capacity may damage

the generator and/or electrical devices connected to it.

ELECTRICAL

POWER MANAGEMENT

To prolong the life of the generator and attached devices,

it is important to take care when adding electrical loads to

the generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the engine

as described later in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity

as previously described.

Example:

Tool or Appliance

Running

Watts*

Additional

Starting Watts*

Window AC,

10,000 BTU

1200 1800

Refrigerator 700 2200

1/3 HP Well Pump 1000 2000

27 in. Television 500 0

Light (75 Watts) 75 0

3475 Total

Running Watts

2200 Highest

Starting Watts

Total Running Watts 3475

Highest Starting Watts + 2200

Total Starting Watts Needed 5675

Application/Equipment

Estimated

Run Watts

Estimated

Starting

Watts

Emergency / Home Standby

Clock Radio 50 50

Lights (qty. 4 x 75 W) 300 300

Refrigerator 700 2200

Furnace Fan 800 2350

Water Well Pump 1000 1500

Microwave 1000 1000

Sump Pump 1050 2200

Electric Range (per element) 2100 2100

Job Site

ElectricDrill−1/2HP 600 900

AirlessSprayer−1/3HP 600 1200

Quartz Halogen Work Light 1000 1000

Reciprocating Saw 960 1920

AirCompressor−1HP 1600 4500

CircularSaw−7-1/4in. 1400 2300

Planer/Jointer−6in 1800 1800

MiterSaw−10in. 1800 1800

TableSaw/RadialArmSaw−10in. 2000 2000

*Wattages listed are approximate. Check tool or appliance for actual wattage.

Page 10 — English

KNOW YOUR GENERATOR

See Figure 1.

The safe use of this product requires an understanding of the

information on the product and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

AC CIRCUIT BREAKERS

The circuit breakers are provided to protect the generator

against electrical overload.

AIR FILTER

The air filter helps to limit the amount of dirt and dust drawn

into the unit during operation.

CHOKE

The choke is used when starting a cold engine.

CORD RETAINERS

Use the cord retainers to prevent plugs from being

accidentally pulled out of the receptacles.

ENGINE SWITCH

The engine switch is used either alone or in combination

with the recoil starter grip to start the generator. To turn the

engine off, place the engine switch in the “OFF” position.

FUEL TANK

The fuel tank has a capacity of 8 gallons.

FUEL VALVE

Fuel flow from the fuel tank to the engine is turned on and

off using the fuel valve.

GROUND TERMINAL

The ground terminal is used to assist in properly ground-

ing the generator to help protect against electrical shock.

Consult with a local electrician for grounding requirements

in your area.

LOW OIL SHUT DOWN PROTECTOR

The low oil sensor causes the engine to stop if the level of

oil in the crankcase is insufficient.

MULTIFUNCTIONAL DISPLAY

The multifunctional display indicates voltage, frequency and

the total number of hours the unit has been used.

OIL CAP/DIPSTICK

Remove the oil fill cap to check and add lubricant to the

generator when necessary.

OIL DRAIN PLUG

When changing the engine lubricant, unscrew and remove

the oil drain plug to allow old engine lubricant to be drained.

RECEPTACLES

Your generator has the following single phase, 60 Hz outlets:

four 120 Volt AC, 20 Amp receptacles, and one 240 Volt

AC, 30 Amp receptacle. These can be used for operating

appropriate appliances, electrical lighting, tools, and motor

loads.

STARTER GRIP AND ROPE

The starter grip and rope is used (along with the engine

switch) to start the generator’s engine.

FEATURES

PRODUCT SPECIFICATIONS

ENGINE

Engine Type .................................................... MZ360, OHV

Fuel Volume ................................................................ 8 gal.

GENERATOR

Rated Voltage .....................................................120V/240V

Rated Amps ..................................................... 56.6A/28.3A

Rated Output ........................................................... 6800 W

Starting Watts .......................................................... 8500 W

Rated Frequency ........................................................60 Hz

DIMENSIONS

Length ................................................................... 31.25 in.

Width ................................................................... 20.625 in.

Height ......................................................................... 24 in.

Weight ................................................................. 222.5 lbs.

Page 11 — English

UNPACKING

This product requires assembly.

 Carefully cut the box down the sides then remove the

machine and any accessories from the box. Make sure

that all items listed in the loose parts list are included.

NOTE: This machine is heavy and requires a minimum of

two people to lift. To avoid back injury, lift with your legs

and not your back.

WARNING:

Do not use this product if any parts on the Loose Parts

List are already assembled to your product when you

unpack it. Parts on this list are not assembled to the

product by the manufacturer and require customer instal-

lation. Use of a product that may have been improperly

assembled could result in serious personal injury.

 Inspect the unit carefully to make sure no damage oc-

curred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-242-4672 for assistance.

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

Do not attempt to operate the generator until assembly

is complete. Failure to comply could result in possible

serious personal injury.

LOOSE PARTS LIST

See Figure 2.

The following items are included with the generator:

Key

No. Description Qty.

1 Bolt (3/8-16 x 4-1/4 in.) .......................................2

2 Lock Nut (3/8-16) .................................................2

3 Washer (3/8 in.) ....................................................2

4 Wheel ...................................................................2

5 Handle Bracket Spacers......................................2

LOOSE PARTS LIST

(CONTINUED)

Key

No. Description Qty.

6 Handle Lock Pin ..................................................2

7 Lanyard ................................................................2

8 Nut (1/4-20) .........................................................2

9 Washer (1/4 in.) ....................................................2

10 Rubber Foot ........................................................2

11 Bolt (1/4-20 x 1-1/2 in.) .......................................2

12 Nut (5/16-18) .......................................................2

13 Washer (5/16 in.) ..................................................4

14 Bolt (5/16-18 x 1 in.) ............................................2

15 Frame Support ....................................................1

16 Engine Lubricant..................................................1

17 Bolt (5/16-18 x 2-1/4 in.) .....................................2

18 Lock Nut (5/16) ....................................................2

19 Handle .................................................................2

20 Spacer (.38 ID) .....................................................2

Operator’s Manual (not shown) ...........................1

TOOLS NEEDED

See Figure 3.

The following tools (not included or drawn to scale) are

needed for assembly:

 Socket Wrenches

 Adjustable Wrench

 Phillips Screwdriver

NOTE: Do not put fuel or lubricant in the generator before

installing the feet, frame support, and wheels.

INSTALLING FEET ON THE FRAME SUPPORT

See Figure 4.

 Locate the following items:

2 rubber feet

2 lock nuts (1/4-20)

2 washers (1/4 in.)

2 bolts (1/4-20 x 1-1/2 in.)

 Insert bolt through foot, then through frame support as

shown.

 Thread washer over the bolt, then install nut. Tighten nut

securely.

NOTE: Be careful not to overtighten so that foot material

collapses.

 Repeat with remaining foot.

INSTALLING THE FRAME SUPPORT

See Figure 4.

Install the frame support on the bottom of the generator

frame on the same side as the handle.

 Locate the following items:

Frame support

2 flange nuts (5/16-18)

4 washers (5/16 in.)

2 bolts (5/16-18 x 1 in.)

ASSEMBLY

Page 12 — English

 Raise the end of the generator where the recoil starter

is located high enough to gain access to the frame bot-

tom; securely position props underneath to support.

 Align the holes on the frame support with the holes on

the generator frame.

 Slide a washer on the bolt, then insert the bolt through

the hole in the generator frame so it extends down

through the frame support.

 Slide a washer on the bolt, then install flange nut and

tighten securely.

 Repeat on other side.

INSTALLING THE WHEELS

See Figure 5.

Wheels are provided to assist in moving the generator to

the desired location and should be installed on the side

opposite the handle.

 Locate the following items:

2 bolts (3/8-16 x 5-1/4 in.)

2 washers (3/8 in.)

2 spacers (.38 ID)

2 wheels

2 lock nuts (3/8-16)

 Raise the end of the generator opposite the handle

high

enough to gain access to the frame bottom; securely

position props underneath to support.



Insert a wheel spacer into the center of the wheel.



Place a washer on the bolt, then slide bolt through the

wheel.



Place a second washer on the bolt, then slide the bolt

through the U-bracket frame on generator.



nstall nut and tighten securely.

 Repeat the process on the other side to install second

wheel.

ATTACHING THE HANDLE

See Figure 6.

 Locate the following items:

2 handles

2 bolt (5/16-8 x 3/4 in.)

4 washers (5/16 in.)

2 lock nuts (5/16)

2 handle bracket spacers

 Place handle and spacer on the frame.

 Place a washer on a bolt, then slide bolt through the

handle, the frame and the spacer.

 Install nut on bolt and tighten securely.

 Repeat the process on the other side to install second

handle.

LOCKING THE HANDLES

See Figures 7 - 8.

 Locate the following items:

2 handle lock pins

2 lanyards

 Attach the lanyard to the handle lock pin and the handle

as shown in figure 7.

 Extend the handle, then insert the pin through the hole

in the handle and the generator frame to secure handle

in place.

 Repeat the process on the other side to lock the other

handle.

CAUTION:

Do not attempt to lift the unit by the handle assembly. If

it is necessary to lift the generator, always grasp by the

frame. Use proper lifting techniques to avoid back injury.

RELEASING THE HANDLES

 Remove the handle lock pins and lower the handles to

the down position.

WARNING:

To reduce the risk of electrocution or explosion, do not

short circuit the battery terminals or charge in a sealed

container. Keep sparks and flame away.

WARNING:

Keep metal objects away from the battery terminals.

Metal objects can make a connection from one terminal

to another. Shorting the battery terminals together could

cause sparks, burns, or a fire.

CONNECTING/DISCONNECTING BATTERY

See Figure 9.

The battery cables must be connected before the electric

start feature of the generator can be operated.

To connect battery cables:

 Connect the red wire to the positive (+) terminal first,

then connect the black wire to the negative (–) terminal.

Make sure all connections are tight.

NOTE: Be careful not to short across the terminals when

installing. Shorting the terminals together can cause

sparks, damage to the battery or generator, or even

burns or explosions.

 Cover the terminals with the rubber covers.

When removing the battery for replacement: disconnect

the negative (black) post, then the positive (red) post, being

careful not to short across the terminals. Always abide by the

safety warnings provided with the battery. Remove the bat-

tery and dispose of according to local and state regulations.

ASSEMBLY

Page 13 — English

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

 Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

 ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See

a doctor. You could have carbon monoxide poisoning.

DANGER:

Failure to properly ground generator can result in elec-

trocution, especially if the generator is equipped with a

wheel kit. National Electric Code requires generator to

be properly grounded to an approved earth ground. Call

an electrician for local grounding requirements.

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

OPERATION

APPLICATIONS

This generator is designed to supply electrical power for

operating compatible electrical lighting, appliances, tools,

and motor loads.

BEFORE OPERATING THE UNIT

 Only use OUTSIDE and far away from windows, doors,

and vents.

 NEVER use inside a home or garage, EVEN IF doors and

windows are open.

 Always position the generator on a flat firm surface.

SPECIAL REQUIREMENTS:

There may be General or State Occupational Safety and

Health Administration (OSHA) regulations, local codes or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

 In some areas, generators are required to be registered

with local utility companies.

 If the generator is used at a construction site, there may

be additional regulations which must be observed.

CHECKING/ADDING LUBRICANT

See Figure 10.

NOTICE:

Attempting to start the engine before it has been properly

filled with lubricant will result in equipment failure.

Engine lubricant has a major influence on engine perfor-

mance and service life. For general, all-temperature use,

SAE 10W-30 is recommended. Always use a 4-stroke mo-

tor lubricant that meets or exceeds the requirements for

API service classification SJ.

NOTE: Non-detergent or 2-stroke engine lubricants will

damage the engine and should not be used.

 Unscrew the oil cap/dipstick and remove.

 Wipe dipstick clean and re-seat in hole; do not re-thread.

 Remove dipstick again and check lubricant level. Lubri-

cant level should fall between the hatched areas on the

dipstick.

 If level is low, add engine lubricant until the fluid level

rises to the upper portion of the dipstick.

 Replace and secure the oil cap/dipstick.

Page 14 — English

USING FUEL STABILIZER

Fuel gets old, oxidizes, and breaks down over time. Adding

a fuel stabilizer (not included) extends the usable life of fuel

and helps prevent deposits from forming that can clog the

fuel system. Follow fuel stabilizer manufacturer’s directions

for correct ratio of stabilizer to fuel.

 Mix fuel stabilizer and gasoline prior to filling the tank

by using a gas can or other approved fuel container and

shaking gently to combine.

NOTE: To control the amount of fuel stabilizer being added

to the engine, always mix fuel stabilizer with gasoline

before fueling the tank rather than adding fuel stabilizer

directly into the generator’s fuel tank.

 Replace and secure the fuel tank cap.

 Start and run the engine for at least 5 minutes to allow

stabilizer to treat the entire fuel system.

OXYGENATED FUELS

NOTICE:

Do not use E15 or E85 fuel (or fuel containing greater

than 10% ethanol) in this product. It is a violation of

federal law and will damage the unit and void your

warranty.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates stated below are not covered

under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E15 and E85

are not.

CHECKING/ADDING FUEL

See Figure 11.

WARNING:

Gasoline and its vapors are highly flammable and ex-

plosive. To prevent serious personal injury and property

damage, handle gasoline with care. Keep away from igni-

tion sources, handle outdoors only, do not smoke while

adding fuel, and wipe up spills immediately.

When adding gas to the generator, make sure the unit is

sitting on a flat, level surface. If the engine is hot, let the

generator cool before adding gas. ALWAYS fill the fuel tank

outdoors with the machine turned off.

 Remove the fuel cap.

 Fill the fuel tank to 1 in. below the top of the fuel neck.

 Replace and secure the fuel cap.

NOTE: Always use unleaded gasoline with a pump octane

rating of 86 or higher. Never use old, stale, or contaminated

gasoline, and do not use an oil/gas mixture. Do not allow dirt

or water into the fuel tank. Do not use E85 fuel.

ELECTRIC START

This generator model is provided with both electric start and

recoil start capabilities. Avoid prolonged cranking, as it can

damage the engine.

The battery provided is a nominal 12 volt sealed recharge-

able lead-acid battery and can be operated in any position

without leakage. It complies with non-spillable battery

regulations. Its convenient size offers a 30% reduction over

conventional batteries.

NOTE: Brand new generators are shipped with the battery

connections disconnected. The positive and negative ter-

minals must be connected to the battery before the Electric

Start feature will work.

For initial battery connection, see Connecting/Disconnect-

ing Battery.

STARTING THE ENGINE

See Figures 11 - 14.

NOTICE:

On a level surface with the engine off, check the lubri-

cant level before each use of the generator.

NOTE: If location of generator is not level, the unit may not

start or may shut down during operation.

 Unplug all loads from the generator.

 Turn the fuel valve to the ON position.

 Move the choke to the START position.

NOTE: If engine is warm or the temperature is above

50˚F,movethechoketotheRUNposition.

 Place the engine switch in the ON position.

 Slide down and hold the lock button while pushing the

engine switch to the START position.

NOTE: The battery may require charging before the gen-

erator can be started using only the engine switch. The

generator can be started by pulling the recoil starter grip.

Once the generator is started, the battery will charge as

the unit runs.

 The generator can also be started by pulling the recoil

starter grip until the engine runs (a maximum of 6 times).

NOTE: Do not allow the grip to snap back after starting;

return it gently to its original place.

 Allow the engine to run for 15-30 seconds, then move

the choke to the RUN position.

STOPPING THE ENGINE

See Figures 11 - 12.

To stop the engine under normal operating conditions:

 Remove any load from the generator.

 Turn the fuel valve to the OFF position.

 Put the engine switch in the OFF ( O ) position.

OPERATION

Page 15 — English

OPERATION

WARNING:

While operating and storing, keep at least 3 feet of clear-

ance on all sides of this product, including overhead.

Allow a minimum of 30 minutes of “cool down” time

before storage. Heat created by muffler and exhaust

gases could be hot enough to cause serious burns and/

or ignite combustible objects.

HIGH ALTITUDE OPERATION

Specific modifications are needed for high-altitude operation.

Please contact your authorized service center for important

information regarding these modifications. Operating this

engine without the proper altitude modification may increase

the engine’s emissions and decrease fuel economy and

performance.

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts could create a hazard or cause

product damage.

Only the parts shown on the parts list are intended to be

repaired or replaced by the customer. All other parts should

be replaced at an authorized service center.

GENERAL MAINTENANCE

Keep the generator in a clean and dry environment where it

is not exposed to dust, dirt, moisture, or corrosive vapors.

Do not allow the cooling air slots in the generator to become

clogged with foreign material such as leaves, etc.

Do not use a garden hose to clean the generator. Water en-

tering the fuel system or other internal parts of the unit can

cause problems that will decrease the life of the generator.

To clean the unit:

 Use a soft bristle brush and/or vacuum cleaner to loosen

and remove dirt and debris.

 Clean air vents with low pressure air that does not exceed

25 psi.

 Wipe the exterior surfaces of the generator with a damp

cloth.

CHECKING/CLEANING AIR FILTER

See Figure 15.

For proper performance and long life, keep air filter clean.

 Release the screws located at the top and bottom of air

filter cover. Remove cover and set aside.

 Remove the filter element.

 If the filter element is dirty, clean with warm, soapy wa-

ter. Rinse and let dry.

 Apply a light coat of engine lubricant to the element,

then squeeze it out.

 Replace the element in the air filter unit.

 Replace the air filter cover; reinstall screws and tighten

securely.

NOTE: Do not run the generator without the air filter. Rapid

engine wear will result.

CHANGING ENGINE LUBRICANT

See Figure 16.

 Remove the oil cap/dipstick.

 Place a container underneath the oil drain plug to collect

used lubricant as it drains.

 Unscrew the oil drain plug and remove.

 Allow lubricant to drain completely.

NOTE: Drain the lubricant while the engine is still warm

but not hot. Warm lubricant will drain quickly and more

completely.

WARNING:

Do not change engine lubricant while it is hot. Accidental

contact with hot engine lubricant could result in serious

burns.

 Reinstall the oil drain plug and tighten securely.

 Refill with lubricant following the instructions in the

Checking/Adding Lubricant section. For amount of

lubricant needed to refill, see Product Specifications

earlier in this manual or the accompanying engine man-

ual, if applicable.

 Reinstall the oil cap/dipstick.

NOTE: Used lubricant should be disposed of at an ap-

proved disposal site. See your local oil retailer for more in-

formation.

Page 16 — English

SPARK PLUG MAINTENANCE

See Figure 17.

The spark plug must be properly gapped and free of deposits

in order to ensure proper engine operation. To check:

 Remove the spark plug cap.

 Clean any dirt from around base of spark plug.

 Remove spark plug using wrench (not included).

 Inspect spark plug for damage, and clean with a wire

brush before reinstalling. If insulator is cracked or

chipped, spark plug should be replaced. For replace-

ment spark plug, see Product Specifications earlier in

this manual or the accompanying engine manual, if ap-

plicable.

 Measurepluggap.Thecorrectgapis0.028−0.031in.

(0.7-0.8 mm). To widen gap, if necessary, carefully bend

the ground (top) electrode. To lessen gap, gently tap

ground electrode on a hard surface.

 Seat spark plug in position; thread in by hand to prevent

cross-threading.

 Tighten with wrench to compress washer. If spark plug

is new, use 1/2 turn to compress washer appropriate

amount. If reusing old spark plug, use 1/8 to 1/4 turn for

proper washer compression.

NOTE: An improperly tightened spark plug will become

very hot and could damage the engine.

CLEANING THE EXHAUST PORT AND

MUFFLER

Depending on the type of fuel used, the type and amount of

lubricant used, and/or your operating conditions, the exhaust

port and muffler may become blocked with carbon deposits.

If you notice a power loss with your gas-powered products,

you may need to remove these deposits to restore perfor-

mance. We highly recommend that only qualified service

technicians perform this service.

MAINTENANCE

SPARK ARRESTOR

See Figure 18.

 Inspect the spark arrestor for breaks or holes. Replace

if necessary. To purchase a replacement spark arrestor

contact Homelite customer service at 1-800-242-4672.

 Use a brush to remove carbon deposits from the spark

arrestor screen as needed.

DRAINING FUEL TANK/CARBURETOR

See Figures 19 - 20.

To help prevent gum deposits in the fuel system, drain the

fuel from the tank and carburetor before storing.

DRAINING THE FUEL TANK

 Turn the engine switch OFF ( O ).

 Turn the fuel valve to the OFF position.

 Remove the fuel line from the petcock by squeezing the

ends of the retaining clip and sliding the fuel line off.

 Install one end of a drain line over the petcock, and

place the other end in a fuel container large enough to

catch the fuel being drained from the tank.

 Turn the fuel valve to the ON position.

 When the fuel has drained from the tank, close the fuel

valve and reinstall fuel line securely on petcock.

DRAINING THE CARBURETOR

 Turn the engine switch OFF ( O ).

 Turn the fuel valve to the OFF position.

 Position a suitable container under the carburetor drain

screw to catch fuel; loosen the screw.

 Allow fuel to drain completely into container.

 Retighten drain screw.

NOTE: Consult hazardous waste management guidelines

in your area for the proper way to dispose of used fuel.

Page 17 — English

TRANSPORTING

 Turn the engine switch OFF ( O ). Disconnect any equip-

ment that is plugged into the generator.

 Turn the fuel valve to the OFF position.

 Allow 30 minutes of “cool down” time before transporting

the machine.

 For security, insert the pins to secure the handles before

transporting.

 Tilt the machine away from you until it balances on the

wheels, then roll the machine to the desired location.

REPLACING FUEL FILTER

See Figure 21.

Occasionally the fuel filter may become clogged and need

replacing. To purchase a replacement fuel filter contact

Homelite customer service at 1-800-242-4672.

NOTE: Fuel tank must be empty before replacing fuel filter.

Run unit until tank is empty, if needed, or inspect filter prior

to fill-up.

To replace:

 Turn the fuel valve to the OFF position.

 Remove the fuel line from both sides of the filter by

squeezing the ends of the retaining clip with pliers.

 Slide the fuel line off.

 Replace with new fuel filter.

 Reinstall fuel lines to new fuel filter.

 Turn the fuel valve to the ON position.

STORING THE GENERATOR

The following steps should be taken when storing the gen-

erator:

 Turn the engine switch OFF ( O ). Disconnect any equip-

ment that is plugged into the generator.

 Turn the fuel valve to the OFF position.

 Allow 45 minutes of “cool down” time before storing the

machine.

 Store the unit in a dry, covered area where the weather

can’t damage it.

NOTE: The unit can be stored with the handles in the up

or down position.

BATTERY REMOVAL AND PREPARATION

FOR RECYCLING

To preserve natural resources, please recycle

or dispose of batteries properly.

This product uses lead acid batteries. Local,

state or federal laws may prohibit disposal of

batteries in ordinary trash.

Consult your local waste authority for information regarding

available recycling and/or disposal options.

WARNING:

Upon removal, cover the battery’s terminals with heavy-

duty adhesive tape. Do not attempt to destroy or disas-

semble battery or remove any of its components. Lead

acid batteries must be recycled or disposed of properly.

Also, never touch both terminals with metal objects and/

or body parts as short circuit may result. Keep away from

children. Failure to comply with these warnings could

result in fire and/or serious injury.

MAINTENANCE

Page 18 — English

MAINTENANCE SCHEDULE

NOTE: If a separate engine manual is provided for this generator, please follow the maintenance schedule provided in the en-

gine manual instead of the maintenance information listed below.

Before

each use

After 1st month

or 20 hours of

operation

Every 3 months

or 50 hours of

operation

Every 6 months

or 100 hours

of operation

Every year or

after 300 hours

of operation

Check Engine Lubricant



Change Engine Lubricant

 

Check Air Filter



Clean Air Filter



Change Air Filter



Check/Adjust Spark Plug



Replace Spark Plug



Check/Adjust Idle Speed



Check/Adjust Valve

Clearance

1,2



Clean Fuel Tank and Filter

1,2



Check Fuel Hose

 

Fuel Filter Inspect Replace

Check All Hose

Connections

 

Inspect Fuel Tank Vapor

Vent (If Equipped)

 

Inspect Carbon Canister

(CARB Models Only)

 

1. These items should only be carried out by an authorized service center.

2. See engine manual for maintenance schedule for this item.

NOTE: Maintenance should be performed more frequently when generator is used in dusty areas.

When generator has exceeded the maximum figures specified in the table, maintenance should still be cycled according

to the intervals of time or hours stated herein.

MAINTENANCE

STORAGE

When preparing the generator for storage, allow the unit to cool completely then follow the guidelines below.

STORAGE TIME PRIOR TO STORING

Less than 2 months  Drain gasoline from tank and dispose of in a suitable container according to state and local ordinances.

2 months to 1 year  Drain fuel from carburetor.

 Drain gasoline from tank and dispose of in a suitable container according to state and local ordinances.

1 year or more  Drain fuel from the carburetor.

 Remove spark plug.

 Drain gasoline from tank and dispose of in a suitable container according to state and local ordinances.

 Put a tablespoon of engine lubricant into the spark plug cylinder. Turn the engine slowly with the pull

rope to distribute the lubricant.

 Reinstall spark plug.

 Change engine lubricant.

After removal from storage:

 Fill with fresh gasoline.

NOTE: If storing gasoline in suitable container for later use, make sure gasoline has been treated with fuel stabilizer

according to stabilizer manufacturer’s instructions.

Page 19 — English

PROBLEM POSSIBLE CAUSE SOLUTION

Engine will not start. Engine switch is OFF.

No fuel.

Stale gasoline or water in gasoline.

Lubricant level is low.

Fuel valve is OFF.

Spark plug faulty, fouled, or improperly

gapped.

Choke lever is in RUN position.

Engine stored without treating or

draining gasoline, or refueled with bad

gasoline.

Dirty fuel filter.

Turn engine switch to ON.

Fill fuel tank.

Drain entire system and refill with fresh

fuel.

Engine is equipped with Low Oil Shutoff.

If engine lubricant level is low, it must be

filled before unit will start. Check engine

lubricant level and fill, if necessary.

Turn fuel valve ON.

Replace spark plug.

Move choke lever to START position.

Drain fuel and carburetor. Refuel with

fresh gasoline.

Replace fuel filter or contact authorized

service center.

Engine hard to start Water in gasoline.

Weak spark at spark plug.

Drain entire system and refill with fresh

fuel.

Contact authorized service center.

Engine lacks power. Dirty air filter.

Engine stored without treating or

draining gasoline, or refueled with bad

gasoline.

Check air filter element. Clean or replace

as needed.

Drain fuel and carburetor. Refuel with

fresh gasoline. If problem continues,

contact your nearest authorized service

center.

AC receptacle does not work. Circuit breaker is OFF.

Item plugged in is defective.

Turn ON the AC circuit breaker.

Try a different item.

Generator makes a “spark knock” or

“pinging” noise.

An occasional light “knocking” or “ping-

ing” under heavy load is not a cause for

concern. However, if the knocking or

pinging occurs under normal load at a

steady engine speed, the problem may

be with the brand of gasoline being used.

Switch to a different brand of gasoline,

making sure that the octane rating is 86

or higher. If problem continues, contact

your nearest authorized service center.

If problem persists after trying the above solutions, contact your nearest authorized service center for assistance.

The following symptoms may indicate problems that will affect the emissions level of the unit:

 Hard starting or stalling after starting

 Rough idle

 Misfiring or backfiring under load

 Afterburning (backfiring)

 Black exhaust smoke or high fuel consumption

If you encounter any of these symptoms, have the unit inspected and repaired by the nearest authorized service center.

TROUBLESHOOTING

Page 20 — English

WARRANTY

LIMITED WARRANTY

WARRANTY COVERAGE

Homelite Consumer Products, Inc., (the Company) warrants to the original retail purchaser that this Homelite Product

is free from defects in material and workmanship and agrees to repair or replace, at the Company’s discretion, any

defective Product free of charge within these time periods from the date of purchase:

 Three years, if the Product is used solely for personal, family, or household use;

 One year, if the Product is used for business or commercial use.

This warranty applies only to Products sold within the United States of America, the District of Columbia, Canada,

Mexico, the Commonwealth of Puerto Rico, the Virgin Islands, or Guam.

This warranty is not transferable and does not cover damage resulting from defects other than in material or workman-

ship, or damage caused by unreasonable use, including the failure to provide reasonable and necessary maintenance.

Other items not covered under this warranty include:

 Transportation charges for sending the product to the Company or its authorized service representative for warranty

service, or for shipping repaired or replacement products back to the customer; these charges must be borne by

the original retail purchaser.

 Damages caused by abuse, accident, misuse, neglect, alteration, modification, the effects of corrosion, erosion,

normal wear and tear or repairs by other than the Company or its authorized service representative.

 In addition this warranty does not cover:

 Tune-ups – Spark Plugs, Carburetor, Carburetor Adjustments, Ignition, Filters, Oil Change

 Wear items – Recoil Starter Rope, Engine Brushes, Cotter Pins, Wheels

Warranty is voided if the customer fails to install, maintain and operate the product in accordance with the instruc-

tions and recommendations of the Company as set forth in the Product’s operator’s manual or if the Product is used

as rental equipment.

The Company will not pay for repairs or adjustments to the Product, or for any costs or labor, performed without the

Company’s prior authorization.

SAVE YOUR SALES SLIP

Proof of purchase in the form of your dated sales receipt, cash register slip, etc., will be required before the Company

and/or its authorized service representatives can perform warranty service on the Product.

EXCLUSIONS AND LIMITATIONS

THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ANY IMPLIED WARRANTY OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, APPLICABLE TO THIS PRODUCT,

SHALL BE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY. THE WARRANTY SERVICE

DESCRIBED ABOVE IS THE EXCLUSIVE REMEDY UNDER THIS WARRANTY. THE COMPANY SHALL NOT BE LIABILE

FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

SOME STATES DO NOT ALLOW A LIMITATION ON THE DURATION OF IMPLIED WARRANTIES, OR THE EXCLUSION

OR LIMITATION OF INCIDENTAL, OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION

MAY NOT APPLY TO YOU.

HOW TO OBTAIN WARRANTY SERVICE

For warranty service: Call toll free 1-800-242-4672, or write to Homelite Consumer Products, Inc., 1428 Pearman

Dairy Road, Anderson, SC 29625.

For warranty service outside the USA, please contact your local Homelite dealer.

Page 21 — English

WARRANTY

Yamaha Motor Corporation USA

Spark Ignited Small Off-Road Equipment (SORE)

Limited and EPA Emissions Warranty

Yamaha Motor Corporation, USA, hereby warrants that new Yamaha Spark Ignited Small Off Road Engines, hereafter called

SORE engines, purchased from an authorized Yamaha SORE engine dealer in the continental United States will be free from

defects in material and workmanship for the period of time stated herein, subject to certain stated limitations.

Period of Warranty — Any new Yamaha SORE engine purchased for private, non-commercial use from an authorized Yamaha

SORE engine dealer in the continental United States will be warrantied against defects in material or workmanship for a period

of three (3) years from date of purchase, subject to exclusions noted herein.

Any Yamaha SORE engine purchased and utilized for commercial applications will be warrantied for a period of one (1) year

from the date of purchase, subject to exclusions noted herein.

For Yamaha SORE engines used in a rental application, the warranty will be for ninety (90) days from the date of purchase,

subject to the exclusions noted herein.

During the period of warranty any authorized Yamaha SORE engine repair station will, free of charge, repair or replace, at

Yamaha’s option, any part adjudged defective by Yamaha due to faulty workmanship or material from the factory. Parts used

in warranty repairs will be warrantied for the balance of the product’s warranty period. All parts replaced under warranty

become property of Yamaha Motor Corporation USA.

Emissions warranty — emissions-related components will be warrantied for 3 years regardless of commercial or non-

commercial use.

General Exclusions from this warranty shall include any failures caused by:

a. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts.

b. Abnormal strain, neglect, or abuse.

c. Lack of proper maintenance.

d. Accident or collision damage.

Specific Exclusions from this warranty shall include parts replaced due to normal wear or routine maintenance.

The Customer’s Responsibility under this warranty shall be to:

1. Operate and maintain the SORE engine as specified in the appropriate Owner’s Manual.

2. Give notice to an authorized Yamaha SORE engine repair station of any and all apparent defects within ten (10) days after

discovery, and make the unit available at time for inspection and repairs as requested by the Yamaha SORE repair station.

An approved Yamaha SORE engine repair station may be found by phoning 1-866-788-7398.

Warranty Transfer: To transfer the warranty from the original purchaser to any subsequent purchaser(s), please contact

1-866-788-7398 to find out the necessary procedures. In no case will the warranty be extended beyond the original period.

Yamaha Motor Corporation, USA, makes no other warranty of any kind, expressed or implied. All implied warranties of mer-

chantability and fitness for a particular purpose which exceed the obligation and time limits stated in this warranty are hereby

disclaimed by Yamaha Motor Corporation, USA, and excluded from this warranty.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Also

excluded from this warranty are any incidental or consequential damages including loss of use. Some states do not allow the

exclusion or limitation of incidental or consequential damages, so the above exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Yamaha Motor Corporation, USA

1-866-788-7398

Page 22 — English

WARRANTY

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The U.S. EPA, Environment Canada, and Homelite Consumer

Products, Inc., are pleased to explain the evaporative emission

control system’s warranty on your small off-road equipment. New

equipment that uses small off-road engines must be designed,

built, and equipped to meet the stringent evaporative standards.

Homelite Consumer Products, Inc., must warrant the evaporative

emission control system on your small off-road equipment for the

period listed below, provided there has been no abuse, neglect or

improper maintenance of your equipment.

Your evaporative emission control system may include parts such

as: carburetors, fuel tanks, fuel line, fuel caps, valves, canisters,

filters, vapor hoses, clamps, connectors, and other associated

components.

MANUFACTURER’S WARRANTY COVERAGE:

This evaporative emission control system is warranted for three

years. If any evaporative emission-related part on your equipment

is defective, the part will be repaired or replaced by Homelite Con-

sumer Products, Inc.

OWNER’S WARRANTY RESPONSIBILITIES:

 As the small off-road equipment owner, you are responsible for

performance of the required maintenance listed in your opera-

tor’s manual. Homelite Consumer Products, Inc., recommends

that you retain all receipts covering maintenance on your small

off-road equipment, but Homelite Consumer Products, Inc.,

cannot deny warranty solely for the lack of receipts.

 As the small off-road equipment owner, you should, however,

be aware that Homelite Consumer Products, Inc., may deny you

warranty coverage if your small off-road equipment or a part

has failed due to abuse, neglect, or improper maintenance or

unapproved modifications.

 You are responsible for presenting your small off-road equip-

ment to a Homelite Consumer Products, Inc., distribution center

or service center as soon as the problem exists. The warranty

repairs should be completed in a reasonable amount of time,

not to exceed 30 days.

If you have a question regarding your warranty coverage, you should

contact Homelite Consumer Products, Inc., at 1-800-242-4672.

DEFECTS WARRANTY REQUIREMENTS:

(a) The warranty period begins on the date the equipment is de-

livered to an ultimate purchaser.

(b) General Evaporative Emissions Warranty Coverage. The equip-

ment must be warranted to the ultimate purchaser and any

subsequent owner that the evaporative emission control system

when installed was:

(1) Designed, built, and equipped so as to conform with all

applicable regulations; and

(2) Free from defects in materials and workmanship that cause

the failure of a warranted part for a period of three years.

interpreted as follows:

(1) Any warranted part that is not scheduled for replacement

as required maintenance in the written instructions must be

warranted for the warranty period defined in subsection (b)

(2). If any such part fails during the period of warranty cov-

erage, it must be repaired or replaced by the manufacturer

issuing the warranty. Any such part repaired or replaced

under the warranty must be warranted for a time not less

than the remaining warranty period.

(2) Any warranted part that is scheduled only for regular inspec-

tion in the written instructions must be warranted for the

warranty period defined in subsection (b)(2). A statement in

such written instructions to the effect of “repair or replace as

necessary” will not reduce the period of warranty coverage.

Any such part repaired or replaced under warranty must be

warranted for a time not less than the remaining warranty

period.

(3) Any warranted part that is scheduled for replacement as

required maintenance in the written instructions must be

warranted for the period of time prior to the first scheduled

replacement point for that part. If the part fails prior to the

first scheduled replacement, the part must be repaired or

replaced by the manufacturer issuing the warranty. Any such

part repaired or replaced under warranty must be warranted

for a time not less than the remainder of the period prior to

the first scheduled replacement point for the part.

(4) Repair or replacement of any warranted part under the

warranty provisions of this article must be performed at no

charge to the owner at a warranty station.

(5) Notwithstanding the provisions of subsection (4) above,

warranty services or repairs must be provided at distribution

centers that are franchised to service the subject equipment.

(6) The owner must not be charged for diagnostic labor that

leads to the determination that a warranted part is in fact

defective, provided that such diagnostic work is performed

at a warranty station.

(7) Throughout the evaporative emission control system’s war-

ranty period set out in subsection (b)(2), the manufacturer

issuing the warranty must maintain a supply of warranted

parts sufficient to meet the expected demand for such parts.

(8) Manufacturer approved replacement parts must be used in

the performance of any warranty maintenance or repairs and

must be provided without charge to the owner. Such use

will not reduce the warranty obligations of the manufacturer

issuing the warranty.

(9) The use of any add-on or modified parts will be grounds

for disallowing a warranty claim made in accordance with

this article. The manufacturer issuing the warranty will not

be liable under this Article to warrant failures of warranted

parts caused by the use of an add-on or modified part.

EMISSION WARRANTY PARTS LIST:

1) Fuel Tank

2) Fuel Cap

3) Fuel Line

4) Carbon Canister

5) Vapor Hoses

6) Hose Clamps

7) Hose Connectors

8) Vapor/Fuel Check Valve

Written instructions for the maintenance and use of the evaporative

emissions control system by the owner shall be furnished with all

new small off-road equipment.

HOMELITE CONSUMER PRODUCTS, INC., FEDERAL EMISSION CONTROL WARRANTY STATEMENT

Page 23 — English

NOTES

Page 2 — Français



Introduction .................................................................................................................................................................... 2



Instructions importantes concernant la sécurité ........................................................................................................3-4



Règles de sécurité particulières ..................................................................................................................................... 4



Symboles ....................................................................................................................................................................5-7



Caractéristiques électriques .......................................................................................................................................8-9



Caractéristiques .......................................................................................................................................................... 10



Assemblage ............................................................................................................................................................11-12



Utilisation ................................................................................................................................................................13-15



Entretien .................................................................................................................................................................. 15-18



Dépannage ................................................................................................................................................................... 19



Garantie ..................................................................................................................................................................20-22



Commande de pièces / réparation ...............................................................................................................Páge arrière

TABLE DES MATIÈRES

INTRODUCTION

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et plus satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

DANGER :

MISE À LA TERRE DU GÉNÉRATEUR

Pour réduire les risques de choc électrique ou d’électrocution, le générateur doit

être correctement mis à la terre. L’écrou et la borne de terre sur le cadre doivent

toujours être utilisés pour connecter le générateur à une source de terre adaptée.

La mise à la terre doit se faire avec un fil de calibre 8. Brancher la borne du fil de

terre entre la rondelle de blocage et l’écrou, puis bien serrer l’écrou. Brancher

l’autre extrémité du fil à une source de terre adaptée.

Le code électrique américain contient diverses façons pratiques permettant

d’établir une bonne source de terre. Si une tige en fer ou en acier est utilisée, elle

doit être d’au moins 15 mm (5/8 po) et si une tige non ferreuse est utilisée, elle

doit avoir un diamètre d’au moins 12,5 mm (1/2 po) et être faite d’un matériau

indiqué pour la mise à la terre. Introduire la tige ou le fourreau à une profondeur

de 2,4 m (8 pieds). Si un fond rocailleux est présent à moins de 1,2 m (4 pieds),

enterrer la tige ou le fourreau dans une tranchée.

Tous les outils et les appareils électriques utilisés à l’aide de ce générateur doivent

être correctement mis à la terre par l’intermédiaire d’un troisième fil ou être doublement isolés.

Il est recommandé :

1. d’utiliser des appareils électriques avec prises de terre à trois fiches.

2. d’utiliser un cordon prolongateur conçus pour l’extérieur avec prise à 3 pôles et une fiche à 3 broches aux extrémités

opposées pour assurer la continuité de la protection de mise à la terre du générateur à l’appareil.

Consulter et respecter tous les réglements nationaux et locaux applicables concernant les spécifications de mise à la

terre. Consulter un électricien qualifié ou le personnel de service si les instructions de mise à la terre ne sont pas bien

comprises, ou en cas de doute au sujet de la mise à la terre.

00:00

120V AC

Page 3 — Français

INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ

DANGER :

Monoxyde de Carbone. Utiliser une génératrice à l’intérieur

d’un bâtiment PEUT CAUSER LA MORT EN QUELQUES

MINUTES.

Le tuyau d’échappement de la génératrice contient un niveau

élevé de monoxyde de carbone (CO), lequel s’avère être un

gaz poison inodore et invisible. Si vous pouvez sentir les gaz

du tuyau d’échappement de la génératrice, vous respirez

du CO. Mais, même si vous ne pouvez pas sentir les gaz

provenant du tuyau d’échappement, vous pourriez être en

train de respirer du CO.

 Ne jamais utiliser une génératrice à l’intérieur d’une

maison, des garages, des petits espaces, ou autres aires

restreintes partiellement fermées. Des niveaux mortels

de monoxyde de carbone peuvent s’accumuler dans

ces aires restreintes. Utiliser un ventilateur ou ouvrir une

fenêtre ou les portes NE fournie PAS assez d’air frais à

respirer.

 Utilisez SEULEMENT la génératrice à l’extérieur et loin

des fenêtres ouvertes, des portes ouvertes, et des

bouches d’aérations. Ces ouvertures peuvent tirer l’air

provenant du tuyau d’échappement.

Même si vous utilisez une génératrice correctement, des gaz

CO peuvent toujours s’infiltrer dans la maison. TOUJOURS

utiliser une alarme de monoxyde de carbone à piles dans

votre maison.

Si vous ressentez que vous commencez à être étourdi

ou faible suite au fonctionnement de la génératrice, allez

prendre l’air frais IMMÉDIATEMENT. Consultez un médecin.

Vous pourriez avoir un empoisonnement au monoxyde de

carbone.

AVERTISSEMENT :

Lire et comprendre toutes les instructions. Le non-respect

de toutes les instructions ci-dessous pourrait entraîner une

électrocution, un incendie et/ou un empoisonnement au

monoxyde de carbone, peut causer des blessures graves,

voire mortelles.

DANGER :

Le code électrique américain (National Electric Code) requiert

que le générateur soit mis à la terre par l’intermédiaire d’une

source de terre approuvée. Avant d’utiliser la borne de terre,

consulter un électricien qualifié, un inspecteur en électricité ou

un organisme local connaissant les codes et les réglements

locaux applicables à l’utilisation prévue du générateur.

CONSERVER CES INSTRUCTIONS

Ce manuel relate à propos d’instructions importantes lesquelles

devraient être suivies pendant l’installation et l’entretien des

piles et de la génératrice.

 Ne pas brancher au circuit électrique d’un bâtiment à moins

que la génératrice et le commutateur de transfert n’aient

été installés correctement par un électricien qualifié, et que

ce dernier n’ait vérifié la sortie électrique. Le branchement

doit isoler l’alimentation de la générateur de la source

d’alimentation de l’appareil et doit répondre à toutes les lois

et codes de l’électricité applicables.

 Ne pas laisser des enfants ou personnes n’ayant pas reçu

une formation adéquate utiliser cette unité.

 Ne pas démarrer ou faire tourner le moteur dans un espace

confine, de bâtiment, à proximité des fenêtres ouverts, autre

ou des zones sans ventilation où des vapeurs toxiques de

monoxyde de carbone peuvent s’accumuler. Le monoxyde

de carbone, un gaz incolore, inodore et extrêmement toxique

peut causer une perte de conscience et être mortel.

 Garder les badauds, enfants et animaux domestiques à une

distance minimum de 3 m (10 pi).

 Porter des chaussures ou des bottes robustes et sèches.

Ne pas utiliser pieds nus.

 Ne pas utiliser le générateur en état de fatigue, si l’on est

souffrant ou sous l’influence de l’alcool, de drogues ou de

médicaments.

 Garder toutes les parties du corps à l’écart des pièces en

mouvement et des parties brûlantes de l’outil.

 Ne pas toucher les prises ou les fils dénudés.

 Ne pas utiliser le générateur avec des cordons électriques

usés, effilochés, dénudés ou autrement endommagés.

 Laisser le moteur refroidir avant de remiser l’outil et vidanger

le carburant.

 Ne pas utiliser le générateur dans la pluie ou la neige.

 Remiser la génératrice dans un endroit bien ventilé après

avoir vider le réservoire de carburant. Ne pas remiser le

carburant à proximité de la génératrice.

 Pour le transport dans un véhicule, le réservoir doit être vide,

le robinet de carburant fermé et la machine bien arrimée.

 Laisser le moteur refroidir pendant 5 minutes avant de faire

le plein.

 Manipuler le carburant avec précaution pour éviter les risques

d’incendies et de brûlures. Le carburant est extrêmement

inflammable.

 Ne pas fumer pendant la manipulation du carburant.

 Conserver le carburant dans un bidon ou jerrican approuvé

pour l’essence.

 Poser la machine sur un sol plat, arrêter le moteur et le laisser

refroidir avant de faire le plein.

 Desserrer le bouchon du réservoir lentement pour relâcher

la pression et éviter que le carburant ne s’échappe.

 Une fois le réservoir plein, remettre le bouchon en place et

le serrer fermement.

 Essuyer tout le carburant éventuellement répandu.

 N’essayer en aucun cas de brûler le carburant répandu.

 Une vibration est normale pendant l’utilisation de

la génératrice. Pendant et après l’utilisation de la

génératrice, inspectez celle-ci, tout comme les câbles

d’extension et les câbles branchés à la boîte d’alimentation

afin de détecter tout bris potentiel du matériel. Faites réparer

tout dommage immédiatement ou remplacer les pièces

endommagées au besoin. Ne pas utiliser de fiches ou des

câbles qui sont endommagés tels qu’ils aient des signes

de fissures ou si la couche isolante est craquée ou si les

lamelles sont endommagées.

Page 4 — Français

INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ

RÈGLES DE SÉCURITÉ PARTICULIÈRES

 Il est préférable d’utiliser une génératrice fixe comme

source d’énergie de secours pour alimenter la maison en

cas de panne d’électricité. Une génératrice portative, même

correctement branchée, risque une surcharge. Il peut en

résulter une surchauffe ou une contrainte indue sur les

composantes du génératrice, ce qui peut provoquer une

défaillance de la génératrice.

 Utiliser uniquement des pièces de rechange et des

accessoires approuvés et suivre les instructions dans la

section Entretien de ce manuel. L’usage de pièces non

autorisées ou le non-respect des instructions peut présenter

des risques de choc électrique ou de blessures.

 Entretenir le produit conformément aux instructions de ce

manuel d’utilisation.

 Inspecter le produit avant chaque utilisation pour s’assurer

qu’il n’y a pas de pièces desserrées, de fuites de carburant,

etc. Remplacer les pièces endommagées.

AVERTISSEMENT :

Lorsque cette génératrice est utilisée pour fournir

de l’énergie à un système électrique d’un bâtiment :

cette génératrice doit être installée par un électricien

qualifié et doit être branchée à un circuit fermé muni d’un

interrupteur de transfert, conformément au Code National

Électrique NFPA70. La génératrice devra être branchée sur

un interrupteur de transfert lequel pourra allumer tous les

conducteurs autres que celui du circuit électrique principal.

Le cadre de la génératrice doit être mis à la terre par

l’intermédiaire d’une source de terre approuvée. Si cette étape

n’est pas faite, la génératrice ne sera pas isolée du circuit

électrique et cela pourrait entraîner des blessures graves,

voire même la mort chez un électricien travaillant pour l’usine.

 NE PAS utiliser cette génératrice pour alimenter les appareils

d’urgence médicale ou le matériel de survie

 Cette génératrice est équipée d’un connecteur neutre lié à

la masse. Cela signifie que le conducteur neutre est relié

électriquement au cadre de l’unité.



L’échappement contient du monoxyde de carbone, un

gaz toxique incolore et inodore. L’inhalation des fumées

d’échappement peut causer la perte de conscience et

le décès. Si la machine tourne dans un endroit clos ou

partiellement clos, l’air peut contenir une quantité dangereuse

de monoxyde de carbone. Pour éviter l’accumulation de

fumées d’échappement, toujours assurer une ventilation

adéquate.



Toujours utiliser un détecteur de monoxyde de carbone

fonctionnant sur piles lors de l’utilisation du générateur.

En cas de sensation de nausée, d’étourdissement ou de

faiblesse lors de l’utilisation du générateur, l’arrêter et aller

immédiatement à l’air frais. Consulter un docteur. Il peut

s’agir d’un empoisonnement au monoxyde de carbone.



Placer le générateur sur une surface stable et plate avec une

pente de pas plus de 4 degrés.



Utiliser dans un endroit bien ventilé et bien éclairé à l’écart

des zones de travail pour éviter les interférences sonores.



L’utilisation du générateur dans des conditions mouillées

peut entraîner l’électrocution. Conserver l’unité au sec.



Garder le générateur à au moins 1 m (3 pieds) de tout type

de matériau combustible.



Ne jamais utiliser le générateur près de matériaux dangereux.



Ne pas utiliser le générateur près d’une station de distribution

d’essence ou de gaz naturel.



Ne pas toucher le silencieux ou le cylindre durant ou

immédiatement après l’utilisation. Ils sont BRÛLANTS et

peuvent provoquer des brûlures.



Ne pas laisser le réservoir d’essence de la génératrice

déborder lors du remplissage. Remplir le réservoir jusqu’à

25,4 mm (1 po) de l’ouverture du goulot du réservoir pour

permettre l’expansion du carburant. Ne pas recouvrir

le bouchon du réservoir de carburant lorsque le moteur

fonctionne. Ne pas respecter cette directive peut

causer une panne de moteur ou endommager l’outil.



Ne pas fumer lors du remplissage du générateur avec de

l’essence.



Fermer le moteur et le laisser refroidir complètement avant

l’ajout de carburant ou la lubrification de la génératrice.



Ne pas retirer la jauge d’huile ou le bouchon du réservoir de

carburant lorsque le moteur tourne.



Bien tenir compte de tous les autocollants de sécurité situés

sur le générateur.



Garder les enfants à un minimum de 3 m (10 pieds) du

générateur à tout moment.



L’unité fonctionne le mieux à des températures comprises

entre -5 et 40 °C (23 et 104 °F) avec une humidité relative

de 90 % ou moins.



Vérifier la tension et la fréquence requises avant de brancher

tout équipement électronique sur le générateur. Le générateur

peut se trouver endommagé si les appareils branchés ne sont

pas prévus pour fonctionner à une tension égale à ± 10% et

une fréquence égale à ± 3 hz de celles indiquées sur la plaque

signalétique du générateur. Pour éviter tout dommage,

toujours brancher une charge additionnelle sur le générateur

lorsqu’un appareil à circuits intégrés (tel qu’un téléviseur)

est utilisé. Une varistance peut être aussi nécessaire

pour certaines applications, dans le cas d’un ordinateur,

par exemple. Une varistance peut être aussi nécessaire

pour certaines applications de l’équipement en solide.

 Lorsque le batteries n’est pas en usage, le garder à l’écart

d’articles tels qu’attaches trombones, pièces de monnaie,

clous, vis et autres petits objets métalliques risquant d’établir

le contact entre les deux bornes. La mise en court-circuit des

bornes de batteries peut causer des étincelles, des brûlures

ou un incendie.



Pour l’utilisation à l’extérieur seulement.



Conserver ces instructions. Les consulter fréquemment et les

utiliser pour instruire les autres utilisateurs éventuels. Si ce

produit est prêté, il doit être accompagné de ces instructions.

Page 5 — Français

SYMBOLES

Les termes de mise en garde suivants et leur signification ont pour but d’expliquer le degré de risques associé à

l’utilisation de ce produit.

SYMBOLE SIGNAL SIGNIFICATION

DANGER :

Indique une situation extrêmement dangereuse qui, si elle n’est pas évitée,

aura pour conséquences des blessures graves, voire mortelles.

AVERTISSEMENT :

Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée,

aura pour conséquences des blessures graves ou mortelles.

ATTENTION :

Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée,

pourrait entraîner des blessures légères ou de gravité modérée.

AVIS :

(Sans symbole d’alerte de sécurité) Indique une information importante ne

concernant pas un risque de blessure comme une situation pouvant

occasionner des dommages matériels.

Certains des symboles ci-dessous peuvent être utilisés sur produit. Veiller à les étudier et à apprendre leur signification. Une

interprétation correcte de ces symboles permettra d’utiliser produit plus efficacement et de réduire les risques.

SYMBOL NAME DESIGNATION/EXPLANATION

Alerte de sécurité Indique un risque de blessure potentiel.

Lire le manuel d’utilisation

Pour réduire les risques de blessures, l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant d’utiliser ce produit.

Avertissement concernant

l’humidité

Ne pas exposer à la pluie ou l’humidité.

Choc électrique

Une utilisation de l’équipement dans des conditions non sèches et le non-

respect des méthodes sans danger peuvent entraîner un choc électrique.

Vapeurs toxiques

Durant le fonctionnement, le générateur émet du monoxyde de carbone,

un gaz toxique inodore et incolore. Respirer le monoxyde de carbone peut

entraîner des nausées, des évanouissements, voire la mort.

Incendie/explosion

Le carburant et ses vapeurs sont extrêmement inflammables et explosifs.

Un incendie ou une explosion peut entraîner des brûlures graves, voire

la mort.

Surface chaude

Pour éviter les risques de blessures ou de dommages, éviter tout contact

avec les surfaces brûlantes.

Danger au levage

Pour réduire le risque de blessures graves, éviter de lever le générateur

seul.

Mise à la terre

Consulter un électricien local pour déterminer les exigences de mise à la

terre avant le fonctionnement.

Électrocution

Une mauvaise mise à la terre du générateur peut causer une électrocution,

surtout si le générateur est équipé d’un kit de roues.

Symbole de recyclage

Ce produit utilise le pile de acide de plomb (Pb). Les réglementations

locales ou gouvernementales peuvent interdire de jeter les piles dans les

ordures ménagères. Consulter les autorités locales compétentes pour les

options de recyclage et/ou l’élimination.

Page 6 — Français

SYMBOLES

AUTOCOLLANTS DE SÉCURITÉ

Les informations ci-dessous se trouvent sur le générateur. Pour des raisons de sécurité, étudier et comprendre tous les

autocollants avant de mettre le générateur en marche.

Si un autocollant se détache ou devient illisible, contacter le centre de réparations agréé pour obtenir un autocollant de

rechange.

 Ne pas procéder de la manière décrite dans ce manuel

d’utilisation entraînera des BLESSURES GRAVES voire

la MORT.

 Risque d’incendie. Ne pas ajouter de carburant pendant

l’utilisation de l’appareil.

 Le générateur est une source potentielle de chocs

électriques. Ne pas exposer à l’humidité, la pluie ou la

neige. Ne pas utiliavec les mains ou les pieds mouillés.

 L’échappement contient le gaz monoxyde de carbone

toxique qui peut causer l’inconscience ou la MORT les

secteurs bien ventilés et extérieurs loin d’ouvre des fenêt

ou des portes.

Certains des symboles ci-dessous peuvent être utilisés sur produit. Veiller à les étudier et à apprendre leur signification. Une

interprétation correcte de ces symboles permettra d’utiliser produit plus efficacement et de réduire les risques.

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Tension

A Ampères Courant

Hz Hertz Fréquence (cycles par seconde)

W Watt Puissance

hrs Heures Durée

gal Gallon Volume

qt Quart Volume

DANGER

PELIGRO

L’utilisation d’une génératrice à l’intérieur PEUT VOUS TUER ENQUELQUES MINUTES.

Les génératrices produisent du monoxyde de carbone, un gaz mortel incolore et inodore.

NE JAMAIS utiliser à l’intérieur d’une maison ou d’un garage,MÊME SI les portes et

les fenêtres sont ouvertes.

Utiliser uniquement À L’EXTÉRIEUR et loin des fenêtres, des portes et des évents.

Usar un generador en el interior PUEDE MATARLO EN POCOS MINUTOS.

Los gases de escape del generador contienen monóxido de carbono. Es un veneno

que no puede verse ni olerse.

NUNCA lo use dentro de su hogar o del garaje, INCLUSO con las puertas y las

ventanas abiertas.

Sólo utilícelo AL AIRE LIBRE y lejos de ventanas, puertas y respiraderos.

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

 Une mauvaise mise à la terre du générateur peut causer

une électrocution, surtout si le générateur est équipé d’un

kit de roue.

 Ne pas exposer à la pluie ou l’humidité.

 L’utilisation d’une génératrice à l’intérieur PEUT VOUS

TUER EN QUELQUES MINUTES. Les génératrices

produisent du monoxyde de carbone, un gaz mortel

incolore et inodore.

 NE JAMAIS utiliser à l’intérieur d’une maison ou d’un

garage, MME SI les portes et les fenêtres sont ouvertes.

 Utiliser uniquement À L’EXTÉRIEUR et loin des fenêtres,

des portes et des évents.

Page 7 — Français

SYMBOLES

AVERTISSEMENT CONCERNANT LE CARBURANT

Ne pas fumer lors du plein. Ne pas trop remplir. Le plein est

obtenu à 25 mm (1 po) en dessous du haut du goulot de

remplissage. Arrêter le moteur pendant cinq minutes avant

de faire le plein pour éviter que la chaleur du silencieux

n’allume les vapeurs de carburant.

MISE À LA TERRE - AVERTISSEMENT

Le code électrique américain (National Electric Code) requiert

que le générateur soit mis à la terre par l’intermédiaire d’une

source de terre approuvée.