Yamaha PSR-E463 El manual del propietario

Marca: Yamaha

Modelo: PSR-E463

Categoría: Instrumentos musicales

Tipo: El manual del propietario

Este manual también es adecuado para

PSR-EW410

DIGITAL KEYBOARD

Owner’s Manual

Thank you for purchasing this Yamaha Digital Keyboard!

The instrument is a portable keyboard with featuring a wide variety of sounds and functions.

We recommend that you read this manual carefully so that you can fully take advantage of the advanced and

convenient functions of the instrument. We also recommend that you keep this manual in a safe and handy place

for future reference.

Before using the instrument, be sure to read “PRECAUTIONS” on pages 5–7.

Setting UpReferenceAppendix Quick Guide

PSR-E463/PSR-EW410 Owner’s Manual

For PSR-E463/PSR-EW410

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply

(adapter). DO NOT connect this product to any power supply or

adapter other than one described in the manual, on the name

plate, or specifically recommended by Yamaha.

WARNING: Do not place this product in a position where any-

one could walk on, trip over, or roll anything over power or con-

necting cords of any kind. The use of an extension cord is not

recommended! If you must use an extension cord, the minimum

wire size for a 25’ cord (or less ) is 18 AWG. NOTE: The smaller

the AWG number, the larger the current handling capacity. For

longer extension cords, consult a local electrician.

This product should be used only with the components supplied

or; a cart, rack, or stand that is recommended by Yamaha. If a

cart, etc., is used, please observe all safety markings and

instructions that accompany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be cor-

rect at the time of printing. However, Yamaha reserves the right

to change or modify any of the specifications without notice or

obligation to update existing units.

This product, either alone or in combination with an amplifier and

headphones or speaker/s, may be capable of producing sound

levels that could cause permanent hearing loss. DO NOT oper-

ate for long periods of time at a high volume level or at a level

that is uncomfortable. If you experience any hearing loss or ring-

ing in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

Some Yamaha products may have benches and / or accessory

mounting fixtures that are either supplied with the produc

t or as

optional acces

sories. Some of these items are designed to be

dealer assembled or installed. Please make sure that benches

are stable and any optional fixtures (where applicable) are well

secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No

other uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to

how a function or effect works (when the unit is operating as

designed) are not covered by the manufacturer’s warranty, and

are therefore the owners responsibility. Please study this manual

carefully and consult your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and

environmentally friendly. We sincerely believe that our products

and the production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the law, we

want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery

which (if applicable) is soldered in place. The average life span

of this type of battery is approximately five years. When replace-

ment becomes necessary, contact a qualified service represen-

tative to perform the replacement.

This product may also use “household” type batteries. Some of

these may be rechargeable. Make sure that the battery being

charged is a rechargeable t

ype and that the charger is intended

for the battery b eing charged.

When installing batteries, never mix old batteries with new ones,

and never mix different types of batteries. Batteries MUST be

installed correctly. Mismatches or incorrect installation may

result in overheating and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all

batteries away from children. Dispose of used batteries promptly

and as regulated by the laws in your area. Note: Check with any

retailer of household type batteries in your area for battery dis-

posal information.

Disposal Notice:

Should this product become damaged beyond repair, or for

some reason its useful life is considered to be at an end, please

observe all local, state, and federal regulations that relate to the

disposal of produc

ts that contain lead, batteri

es, plastics, etc. If

your dealer is unable to assist you, please contact Yamaha

directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The

model number, serial number, power requirements, etc., are

located on this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided below

and retain this manual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Digital Keyboard

Model Name : PSR-E463/PSR-EW410

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that

may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

(FCC DoC)

PSR-E463/PSR-EW410 Owner’s Manual

The model number, serial number, power requirements, etc.,

may be found on or near the name plate, which is at the bottom

of the unit. You should note this serial number in the space

provided below and retain this manual as a permanent record of

your purchase to aid identification in the event of theft.

Model No.

Serial No.

(bottom_en_01)

For AC adaptor and PSR-E463/PSR-EW410

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifica-

tions not expressly approved by Yamaha may void your author-

ity, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions cou ld void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these requirements

provides a reasonable level of assurance that your use of this

product in a residential environment will not result in harmful

interference with other electronic devices. This equipment gen-

erates/uses radio frequencies and, if not installed and used

according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic

devices. Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this product

is found to be the source of interference, which can be deter-

mined by tur

ning the unit “OFF”

and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected

by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distribute

this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America, Elec-

tronic Service Division, 6600 Orangethorpe Ave, Buena Park,

CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

FCC INFORMATION (U.S.A.)

(class B)

PSR-E463/PSR-EW410 Owner’s Manual

For AC adaptor

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and main-

tenance (servicing) instructions in the liter-

ature accompanying the product.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accor-

dance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-

cles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tri-

pod, bracket, or table specified

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualified service personnel. Ser-

vicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT SAFETY INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAN ICES-3 (B)/NMB-3(B)

(can_b_02)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

PSR-E463/PSR-EW410 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

For AC adaptor

WARNING

• This AC adaptor is designed for use with only Yamaha electronic

instruments. Do not use for any other purpose.

• Indoor use only. Do not use in any wet environments.

CAUTION

• When setting up, make sure that the AC outlet is easily

accessible. If some trouble or malfunction occurs, immediately

turn off the power switch of the instrument and disconnect the AC

adaptor from the outlet. When the AC adaptor is connected to the

AC outlet, keep in mind that electricity is flowing at the minimum

level, even if the power switch is turned off. When you are not

using the instrument for a long time, make sure to unplug the

power cord from the wall AC outlet.

For PSR-E463/PSR-EW410

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or

even death from electrical shock, short-circuiting, damages, fire or other hazards. These

precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or

radiators. Also, do not excessively bend or otherwise damage the

cord, or place heavy objects on it.

• Only use the voltage specified as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

• Use the specified adaptor (page 80) only. Using the wrong

adaptor can result in damage to the instrument or overheating.

• Use only the supplied power cord/plug.

• Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it.

• This instrument contains no user-serviceable parts. Do not

attempt to disassemble or modify the internal components in any

way. If it should appear to be malfunctioning, discontinue use

immediately and have it inspected by qualified Yamaha service

personnel.

• Do not expose the instrument to rain, use it near water or in damp

or wet conditions, or place on it any containers (such as vases,

bottles or glasses) containing liquids which might spill into any

openings. If any liquid such as water seeps into the instrument,

turn off the power immediately and unplug the power cord from

the AC outlet. Then have the instrument inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning

item may fall over and cause a fire.

Power supply/AC adaptor

Do not open

Water warning

Fire warning

DMI-5 1/3

PSR-E463/PSR-EW410 Owner’s Manual

• Follow the precautions below. Failure to do so might result in

explosion, fire, overheating or battery fluid leakage.

- Do not tamper with or disassemble batteries.

- Do not dispose of batteries in fire.

- Do not attempt to recharge batteries that are not designed to be

charged.

- Keep the batteries separate from metallic objects such as

necklaces, hairpins, coins, and keys.

- Use the specified battery type (page 80) only.

- Use new batteries, all of which are the same type, same model,

and made by the same manufacturer.

- Always make sure all batteries are inserted in conformity with

the +/- polarity markings.

- When the batteries run out, or if the instrument is not to be

used for a long time, remove the batteries from the instrument.

- When using Ni-MH batteries, follow the instructions that came

with the batteries. Use only the specified charger device when

charging.

• Keep batteries away from small children who might accidentally

swallow them.

• If the batteries do leak, avoid contact with the leaked fluid. If the

battery fluid should come in contact with your eyes, mouth, or

skin, wash immediately with water and consult a doctor. Battery

fluid is corrosive and may possibly cause loss of sight or

chemical burns.

• When one of the following problems occur, immediately turn off

the power switch and disconnect the electric plug from the outlet.

(If you are using batteries, remove all batteries from the

instrument.) Then have the device inspected by Yamaha service

personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you

or others, or damage to the instrument or other property. These precautions include, but are not

limited to, the following:

• Do not connect the instrument to an electrical outlet using a

multiple-connector. Doing so can result in lower sound quality, or

possibly cause overheating in the outlet.

• When removing the electric plug from the instrument or an outlet,

always hold the plug itself and not the cord. Pulling by the cord

can damage it.

• Remove the electric plug from the outlet when the instrument is

not to be used for extended periods of time, or during electrical

storms.

• Do not place the instrument in an unstable position where it might

accidentally fall over.

• Before moving the instrument, remove all connected cables, to

prevent damage to the cables or injury to anyone who might trip

over them.

• When setting up the product, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction occurs,

immediately turn off the power switch and disconnect the plug

from the outlet. Even when the power switch is turned off,

electricity is still flowing to the product at the minimum level.

When you are not using the product for a long time, make sure to

unplug the power cord from the wall AC outlet.

• Use only the stand/rack specified for the instrument. When

attaching it, use the provided screws only. Failure to do so could

cause damage to the internal components or result in the

instrument falling over.

• Before connecting the instrument to other electronic components,

turn off the power for all components. Before turning the power on

or off for all components, set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum

levels and gradually raise the volume controls while playing the

instrument to set the desired listening level.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps

on the panel or keyboard. This could cause physical injury to you

or others, damage to the instrument or other property, or

operational failure.

• Do not rest your weight on, or place heavy objects on the

instrument, and do not use excessive force on the buttons,

switches or connectors.

Battery

If you notice any abnormality

Power supply/AC adaptor

Location

Connections

Handling caution

DMI-5 2/3

PSR-E463/PSR-EW410 Owner’s Manual

• Do not use the instrument/device or headphones for a long period

of time at a high or uncomfortable volume level, since this can

cause permanent hearing loss. If you experience any hearing loss

or ringing in the ears, consult a physician.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

Make sure to discard used batteries according to local regulations.

DMI-5

3/3

NOTICE

To avoid the possibility of malfunction/ damage

to the product, damage to data, or damage to

other property, follow the notices below.

 Handling

• Do not use the instrument in the vicinity of a TV, radio,

stereo equipment, mobile phone, or other electric

devices. Otherwise, the instrument, TV, or radio may

generate noise. When you use the instrument along with

an application on your iPad, iPhone or iPod touch, we

recommend that you set “Airplane Mode” to “ON” on that

device in order to avoid noise caused by communication.

• Do not expose the instrument to excessive dust or

vibrations, or extreme cold or heat (such as in direct

sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disfiguration, damage to

the internal components or unstable operation. (Verified

operating temperature range: 5° – 40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the

instrument, since this might discolor the panel or

keyboard.

 Maintenance

• When cleaning the instrument, use a soft cloth. Do not

use paint thinners, solvents, alcohol, cleaning fluids, or

chemical-impregnated wiping cloths.

 Saving data

• Some of the data of this instrument (page 49) are retained

when the power is turned off. However, the saved data

may be lost due to some failure, an operation mistake,

etc. Save your important data onto USB flash drive/an

external device such as a computer (pages 47, 72).

Before using a USB flash drive, make sure to refer to page

78.

• To protect against data loss through USB flash drive

damage, we recommend that you save your important

data onto spare USB flash drive or an external device

such as a computer as backup data.

Information

 About copyrights

• Copying of the commercially available musical data

including but not limited to MIDI data and/or audio data

is strictly prohibited except for your personal use.

• This product incorporates and bundles contents in which

Yamaha owns copyrights or with respect to which

Yamaha has license to use others’ copyrights. Due to

allowed to distribute media in which these contents are

saved or recorded and remain virtually the same or very

similar to those in the product.

* The contents described above include a computer

program, Accompaniment Style data, MIDI data, WAVE

data, voice recording data, a score, score data, etc.

* You are allowed to distribute medium in which your

performance or music production using these contents

is recorded, and the permission of Yamaha Corporation

is not required in such cases.

 About functions/data bundled with the

instrument

• Some of the preset songs and the songs that can be

downloaded from the Yamaha website have been edited

for length or arrangement, and may not be exactly the

same as the original.

 About this manual

• The illustrations and LCD screens as shown in this

manual are for instructional purposes only, and may

appear somewhat different from those on your

instrument.

• Windows is a registered trademark of Microsoft®

Corporation in the United States and other countries.

• iPhone, iPad, iPod touch and macOS are trademarks of

Apple Inc., registered in the U.S. and other countries.

• IOS is a trademark or registered trademark of Cisco in the

U.S. and other countries and is used under license.

• The company names and product names in this manual

are the trademarks or registered trademarks of their

respective companies.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

PSR-E463/PSR-EW410 Owner’s Manual

Setting Up Reference AppendixQuick Guide

Table of Contents

Special Features.............................................................. 8

Compatible Format and Functions................................. 10

Included Accessories..................................................... 10

About the Manuals......................................................... 11

Setting Up

Panel Controls and Terminals 12

Setting Up 14

Power Requirements ..................................................... 14

Turning the Power On/Off.............................................. 16

Adjusting the Master Volume......................................... 16

Using a Keyboard Stand................................................ 17

Quick Guide

Basic Operation and Display Items 18

Basic Operation ............................................................. 18

Display Items ................................................................. 19

Try Playing a Variety of Instrument Voices 20

Selecting a Main Voice .................................................. 20

Playing the “Grand Piano” ............................................. 20

Layering a Dual Voice.................................................... 20

Playing a Split Voice in the Left Hand area ................... 21

Using the Metronome .................................................... 21

Adding Harmony/Triggering Arpeggios.......................... 22

Changing the Harmony and Arpeggio types.................. 23

Adding DSP Effects ....................................................... 24

Creating Original Sounds via the Knobs 25

Assigning Functions to the Knobs ................................. 25

Switching the Target...................................................... 25

Using the Knobs ............................................................ 25

Playing Styles 26

Playing Songs27

Listening to a Demo Song ............................................. 28

Selecting and Playing Back a Song ............................... 28

Song Fast Forward, Fast Reverse, and Pause.............. 28

Playing a Specified Section of a Song Repeatedly (A-B Repeat)

.. 29

Turning Each Track On/Off............................................ 29

Playing with Groove Creator 30

Playing with Quick Sampling 31

Playing back the Samples ............................................. 31

Getting Ready for Sampling........................................... 31

Sampling External Audio Sound .................................... 32

Restoring the Default Samples ...................................... 34

Saving a Sample to a USB Flash Drive ......................... 34

Loading a Sample from a USB Flash Drive ................... 35

Deleting a Sample in the USB Flash Drive .................... 35

Playing Like a DJ! 36

Creating an Intro Part with the Track On/Off Controls ... 36

Building Excitement and Interest by Changing Sections

... 36

Adding Effects to the Groove with the Live Control Knobs

... 36

Creating Greater Excitement with the Retrigger Function

... 37

Switching to Another Groove with Musical Climax ........ 37

Recording Your Performance 38

Track Structure of a Song .............................................. 38

Quick Recording ............................................................ 38

Recording to a Specified Track...................................... 39

Clearing a User Song .................................................... 40

Clearing a Specified Track from a User Song ............... 40

Audio Playback and Recording 41

Playing back an Audio File in a USB Flash Drive .......... 41

Recording/Saving Audio Files to a USB Flash Drive ..... 42

Deleting Audio Files from the USB Flash Drive ............. 43

Memorizing Your Favorite Settings (Registration Memory)

Memorizing Panel Settings to the Registration Memory

... 44

Recalling Panel Settings from the Registration Memory

... 44

Connecting to Other Devices 45

Connecting Headphones or an External Device............ 45

Using a Pedal (Sustain) ................................................. 45

Playing an External Audio Device with the Built-in Speakers

... 46

Using the Melody Suppressor........................................ 46

Play the keyboard with any one of the amaz-

ingly rich and wide-ranging 758 voices.

( Page 20)

Take your performance to new levels—what-

ever music you play—with 235 auto accompa-

niment Styles. ( Page 26)

The 10 DSP (Digital Signal Processor) effects

provide powerful ways to enhance and totally

change the sound. ( Page 24)

The two Live Control Knobs let you add

dynamic sound variations—including classic

filter effects, distortion and reverb—giving you

the tools to completely transform the sound.

( Page 25)

Groove Creator Page 30

Groove Creator gives you a full selection of powerful

dance rhythms—plus amazing real-time controls and

DSP effects to help you sound and perform like a pro

DJ.

Live Control Knobs

Section Change

DSP Effect

Tra c k On / Off

Special Features

Table of Contents

PSR-E463/PSR-EW410 Owner’s Manual

Setting UpReferenceAppendix Quick Guide

Using with Computer or Smart Device........................... 47

Using an External Stereo System for Playback

(OUTPUT [L/L+R]/[R] jacks) (PSR-EW410) .............. 48

Speaker Mute On/Off Setting (PSR-EW410)................. 48

Backup and Initialization 49

Backup Parameters ....................................................... 49

Initializing the Instrument............................................... 49

Reference

Handy Performance Features 50

Selecting a Reverb Type ............................................... 50

Selecting a Chorus Type ............................................... 50

Pitch Controls—Transpose............................................ 51

Pitch Controls—Fine Tuning.......................................... 51

Pitch Controls—the [PITCH BEND] w heel..................... 51

Calling Up Optimum Panel Settings—One Touch Setting (OTS)

.. 51

Changing the Touch Response of the Keyboard........... 52

Selecting an EQ Setting for the Best Sound.................. 52

Scale Tuning 53

Selecting a Scale ........................................................... 53

Setting the Base Note for Each Scale ........................... 53

Tuning Each Note to Create an Original Scale.............. 54

Voice Settings55

Selecting a Dual Voice................................................... 55

Selecting a Split Voice ................................................... 55

Voice Editing.................................................................. 55

Arpeggio Settings56

Synchronizing an Arpeggio to Song/Style/Groove

Playback—Arpeggio Quantize................................... 56

Holding the Arpeggio Playback via the Footswitch........ 56

Parameters Assigned to the Knobs 57

Style and Groove Settings59

Style Variations—Sections ............................................ 59

Style Synchro Stop ........................................................ 60

Turning Each Style Track On/Off................................... 60

Groove Variations—Sections......................................... 61

Groove Retrigger Function ............................................ 61

Changing the Tempo ..................................................... 61

Tap Start ........................................................................ 61

Adjusting the Volume of the Style or Groove................. 62

Setting the Split Point .................................................... 62

Playing Chords Without Style Playback (Stop Accompaniment)

.. 62

Chord Types for Style Playback .................................... 63

Song Settings64

Background Music Playback.......................................... 64

Random Song Playback ................................................ 64

Tempo Setting of the Song ............................................ 65

Tap Start ........................................................................ 65

Song Volume ................................................................. 65

Melody Voice Setting of the Preset Song ...................... 65

The Functions 66

Basic Procedure in the Function Display ....................... 66

USB Flash Drive Operations 70

Connecting a USB Flash Drive ...................................... 71

Formatting a USB Flash Drive ....................................... 72

Saving User Data to a USB Flash Drive ........................ 72

Saving a User Song as SMF to a USB Flash Drive....... 73

Loading User Data from a USB Flash Drive .................. 74

Loading a Style File ....................................................... 75

Deleting a User File in the USB Flash Drive .................. 76

Deleting an SMF File in the USB Flash Drive ................ 76

Exiting from a File Control Display................................. 77

Message List.................................................................. 77

Appendix

Troubleshooting.............................................................. 78

Specifications ................................................................. 79

Index............................................................................... 81

Quick Sampling Pag e 31

The Quick Sampling feature lets you sample short

sounds from an external device, and play them from

the keyboard—as rhythm loops, melodies or sound

effects—giving you even greater creative expressive

tools for your performance.

USB Audio Recording Page 41

This convenient feature lets you record your perfor-

mances to a USB flash drive. Since the recorded data

is saved as an audio file, you can easily play it back

on a computer or portable audio player.

PSR-E463/PSR-EW410 Owner’s Manual

Setting Up

Included Accessories

•Owner’s Manual (this book)

• AC adaptor

•Power cord (PSR-EW410)

•Music rest

• Online Member Product Registration

* May not be included depending on your area. Check with your Yamaha dealer.

Compatible Format and Functions

GM System Level 1

“GM System Level 1” is an addition to the MIDI standard which ensures that any GM-com-

patible music data can be accurately played by any GM-compatible tone generator,

regardless of manufacturer. The GM mark is affixed to all software and hardware products

that support GM System Level.

XGlite

As its name implies, “XGlite” is a simplified version of Yamaha’s high-quality XG tone gen-

eration format. Naturally, you can play back any XG song data using an XGlite tone gener-

ator. However, keep in mind that some songs may play back differently compared to the

original data, due to the reduced set of control parameters and effects.

USB

USB is an abbreviation for Universal Serial Bus. It is a serial interface for connecting a

computer with peripheral Devices. It allows “hot swapping” (connecting peripheral devices

while the power to the computer is on).

STYLE FILE FORMAT (SFF)

The Style File Format is Yamaha’s original style file format which uses a unique conver-

sion system to provide high-qu ality automatic accompaniment based on a wide range of

chord types.

Insert the music rest

into the slots as

shown.

Attaching the Music Rest

PSR-E463/PSR-EW410 Owner’s Manual

Setting Up

About the Manuals

This instrument has the following documents and instructional materials.

 Included Documents

Owner’s Manual (this book)

• Setting Up Please read this section first.

• Quick Guide This section explains how to use the basic functions.

• Reference This section explains how to make detailed settings for the various functions

of the instrument.

• Appendix This section includes troubleshooting and specifications.

 Online Materials (PDF)

Data List

Contains various important preset content lists such as those of Voices, Styles, Grooves and

Effects.

MIDI Reference

Contains MIDI-related information for this instrument.

MIDI Basics (only in English, French, German and Spanish)

Contains basic explanations about MIDI.

Computer-related Operations

Includes instructions on connecting this instrument to a computer, and operations related to trans-

mitting/receiving the data.

iPhone/iPad Connection Manual

Explains how to connect the instrument to smart devices, such iPhone, iPad, etc.

To see the above materials, access the Yamaha website. Open the following website, enter the model name and

search them.

Yamaha Dawnloads https://download.yamaha.com/

• The illustrations and displays as shown in this manual are based on the PSR-E463.

• Please note that the PSR-E463 and PSR-EW410 have different numbers of keys: the PSR-E463 has 61 keys, and the PSR-EW410 has

76 keys.

 Song Book/Song Data

To o btain these materials, access the Yamaha website at “Download” tab below the model name.

Song Book (only in English, French, German, Spanish and Japanese)

Contains music scores for the preset Songs (excluding the Demo Songs) of this instrument and

the optional Songs.

Song Data

Contains the data of 70 Songs that can be played back with this instrument.

NOTE

• The downloaded Song data can be played back by transferring data from the computer to the instrument or saving data to the

USB flash drive (page 27).

NOTE

PSR-E463/PSR-EW410 Owner’s Manual

Setting Up

!9 @0 @1

e r t y

u i o !0

036

(C1)

048

(C2)

060

(C3)

072

(C4)

084

(C5)

096

(C6)

Panel Controls and Terminals

• Voice List (Data List)

• Style List (Data List)

• Song List (Data List)

• Groove List (Data List)

Dial (page 18)

Display (page 19)

As illustrated, each note of the key-

board has a specific note number

and name (e.g., 036/C1), which is

used in making various settings,

such as Split Point (page 62).

PSR-E463: 036 (C1) – 096 (C6)

PSR-EW410: 028 (E0) – 103 (G6)

The illustration is of the PSR-E463.

Setting Up

Front Panel

Panel Controls and Terminals

PSR-E463/PSR-EW410 Owner’s Manual

Setting Up

q [ ] (Standby/On) switch .................... page 16

w [MASTER VOLUME] control ................. page 16

e [QUICK SAMPLING] button .................. page 20

r [DEMO] button....................................... page 28

t [TRANSPOSE] button ........................... page 51

y [MELODY SUPPRESSOR] button......... page 46

u [AUDIO] button ...................................... page 41

i [REC] button.......................................... page 38

o [METRONOME] button.......................... page 21

!0 [TEMPO/TAP] button............................. page 61

!1 VOICE CONTROL section

[SPLIT] button.................................... page 21

[DUAL] button .................................... page 20

[HARMONY/ARPEGGIO] button ....... page 22

[DSP] button....................................... page 24

!2 LIVE CONTROL section

[KNOB ASSIGN] button..................... page 25

[A] and [B] knobs .............................. page 25

[TARGET] button ....................... pages 24, 25

!3 CATEGORY buttons .............................. page 18

!4 [FUNCTION] button ............................... page 66

!5 [PORTABLE GRAND] button................ page 20

!6 Number buttons [1]–[9], [-/NO],

[0/EXECUTE] and [+/YES] buttons ...... page 18

!7 REGISTRATION MEMORY buttons

[BANK/MEMORY] buttons................. page 44

[1]–[4] buttons.................................... page 44

!8 [VOICE] button ...................................... page 20

!9 [STYLE] button...................................... page 26

@0 [SONG] button....................................... page 28

@1 [GROOVE CREATOR] button................ page 30

@2 GROOVE CREATOR/SONG/STYLE Control

buttons

• When the [GROOVE CREATOR] lamp is on:

.................................. pages 30 and 61

• When the [SONG/AUDIO] lamp is on:

................................................ page 28

• When the [STYLE] lamp is on:

........................... pages 26, 59, and 60

3 TR

ACK CONTROL buttons

• When the [GR

OOVE CREATOR] lamp is on:

................................................ page 30

• When the [SONG/AUDIO] lamp is on:

........................................ pages 29, 38

• When the [STYLE] lamp is on:

................................................ page 60

@4 [PITCH BEND] wheel ............................ page 51

@5 Drum illustrations for the Drum Kit..... page 20

These indicate the drum or percussion instrument

assigned to the corresponding keys (in the case of “Stan-

dard Kit 1,” shown in the Drum/SFX Kit List of the online

material Data List).

Rear Panel

@6 OUTPUT [L/L+R]/[R] jacks (PSR-EW410)

................................................ page 48

@7 [SUSTAIN] jack...................................... page 45

@8 [PHONES/OUTPUT] jack (PSR-E463),

[PHONES] jack (PSR-EW410) .............. page 45

@9 [AUX IN] jack ......................................... page 46

#0 [USB TO DEVICE] terminal .................. page 70

[USB TO HOST] terminal...................... page 47

#1 DC IN jack...............................................page 14

Panel Setup (Panel Settings)

By using the controls on the panel, you can make vari-

ous settings as described here. These settings of the

instrument are together referred to as “panel setup” or

“panel settings” in this manual.

@7 @8 @9

#0 #1

@7@6 @8 @9

#0 #1

PSR-EW410

PSR-E463

PSR-E463/PSR-EW410 Owner’s Manual

Setting Up

Power Requirements

Although the instrument will run either from an AC

adaptor or batteries, Yamaha recommends use of an

AC adaptor whenever possible. An AC adaptor is

more environmentally friendly than batteries and

does not deplete resources.

Using an AC Adaptor

Connect the AC adaptor in the order shown in the

illustration.

Using Batteries

This instrument requires the following batteries.

• PSR-E463: Six “AA” size alkaline (LR6), manganese

(R6) or Ni-MH rechargeable batteries.

• PSR-EW410: Six “D” size alkaline (LR20), manga-

nese (R20) or Ni-MH rechargeable batteries.

The Alkaline batteries or rechargeable Ni-MH batter-

ies are recommended for this instrument, since other

types may result in poorer battery performance.

1 Make sure that the power of the instrument is off.

2 Open the battery compartment cover located on

the instrument’s bottom panel.

• You should use an AC adaptor when executing USB flash

drive operations, since battery power may not be reliable

enough to last through these crucial operations.

• Use the specified AC adaptor (page 80) only. Using the

wrong AC adaptor can result in damage to the instrument

or overheating.

• When using the AC adaptor with a removable plug, make

sure to keep the plug attached to the AC adaptor. Using the

plug alone can cause electric shock or fire.

• Never touch the metallic section when attaching the plug.

To avoid electric shock, short circuit or damage, also be

careful that there is no dust between the AC adaptor and

plug.

NOTICE

AC outlet

adaptor

DC IN jack

(page 13)

PSR-EW410

PSR-E463

DC IN jack

(page 13)

AC outlet

Power cord

adaptor

The shape of the plug differs

depending on your area.

WARNING

WARNING (PSR-E463)

• When setting up the product, make sure that the AC outlet

you are using is easily accessible. If some trouble or mal-

function occurs, immediately turn the power off and dis-

connect the plug from the outlet.

• Follow this procedure in reverse order when disconnecting

the AC adaptor.

• When using Ni-MH batteries, follow the instructions that

came with the batteries.

Slide the plug as

indicated.

Plug

The shape of the plug differs

depending on your area.

CAUTION

NOTE

NOTICE

PSR-E463

Setting Up

PSR-E463/PSR-EW410 Owner’s Manual

Setting Up

3 Insert the six new batteries, putting them in the

correct direction according to the illustration.

4 Replace the compartment cover, making sure

that it locks firmly in place.

 Setting the battery type

Depending on the battery type to be used, you may

need to change the battery type setting on this instru-

ment. To change the setting, first turn on the power to

the instrument, then choose the battery type you

would like to use. Alkaline (and manganese) batter-

ies are chosen by default. For details, refer to page

69, Function 064 (PSR-E463)/Function 065 (PSR-

EW410).

 Checking the power status

Yo u can confirm the power source at the left corner

of the display.

: The power is supplied from the AC adaptor.

: The power is supplied from the batteries.

Remaining battery power indication

• Connecting or disconnecting the AC adaptor with batter-

ies installed may turn the power off, resulting in loss of

data being recorded or transferred at the time.

• Make sure to set the battery type correctly (page 15).

• When battery power becomes too low for proper opera-

tion, the volume may be reduced, the sound may be dis-

torted, and other problems may occur. When this happens,

make sure to replace all batteries with new ones or

already-recharged ones.

PSR-EW410

PSR-E463

NOTICE

• This instrument cannot charge the batteries. Use only the

specified charger device when charging.

• Power will be automatically drawn from the AC adaptor if an

AC adaptor is connected while batteries are installed in the

instrument.

• Failure to set the battery type may shorten the amount of

the battery life. Make sure to set the battery type correctly.

• When the AC adaptor is plugged in to the AC outlet, the bat-

tery icon does not appear even when batteries are inserted. In

this case, the power is supplied from the AC adaptor.

Indicates that the power will be turned off

immediately. When rechargeable batteries

are used, this icon flashes before the power

is turned off.

Indicates that remaining power is insufficient

for operation. Before the power runs out,

replace all the batteries with new ones, or

fully recharged ones (when using recharge-

able types). Note that the instrument may

not work properly, including unusually soft

volume and poor sound quality when

remaining power becomes low.

Indicates that the remaining power is suffi-

cient.

NOTE

NOTICE

GrandPno

Only one of these is shown.

NOTE

Setting Up

PSR-E463/PSR-EW410 Owner’s Manual

Setting Up

Turning the Power On/Off

1 Turn down the [MASTER VOLUME] control to

“MIN”.

2 Press the [ ] (Standby/On) switch to turn the

power on.

3 Press and hold the [ ] (Standby/On) switch for

about a second to turn the power off.

Setting the Auto Power Off function

To p r e vent unnecessary power consumption, this

instrument features an Auto Power Off function that

automatically turns the power off if the instrument is

not operated for a specified period of time. The

amount of time that elapses before the power is auto-

matically turned off is 30 minutes by default; however,

you can change the setting. For details, refer to

page

, Function 063 (PSR-E463)/Function 064 (PSR-

EW410).

 Disabling Auto Power Off (simple method)

Turn the power on while holding down the lowest key

on the keyboard. This starts the instrument with the

Auto Power Off function disabled.

Adjusting the Master Volume

To adjust the volume of the entire keyboard sound,

use the [MASTER VOLUME] control while playing

the keyboard.

• Even when the power is off, a small amount of electricity is

still being consumed by the instrument. When you are not

using the instrument for a long time, make sure to unplug

the AC adaptor from the wall AC outlet.

• Press only the [ ] (Standby/On) switch when turning the

power on. Any other operations such as pressing keys,

buttons or the pedal are not allowed. Doing so may cause

the instrument to malfunction.

CAUTION

NOTICE

PSR-EW410

PSR-E463

The lowest key

• When the instrument is not operated for a specified period

of time while connected to an external device such as an

amplifier, speaker or computer, make sure to follow the

instructions in the Owner’s Manual to turn off the power to

the instrument and the connected devices, in order to pro-

tect the devices from damage. If you do not want the

power to turn off automatically when a device is con-

nected, disable Auto Power Off.

• Generally, the data and settings are maintained even when

the power is turned off. For details, see page 49.

• Do not use the instrument for a long period of time at a

high or uncomfortable volume level, since this can cause

permanent hearing loss.

NOTICE

NOTE

CAUTION

Setting Up

PSR-E463/PSR-EW410 Owner’s Manual

Setting Up

Using a Keyboard Stand

The following keyboard stands (sold separately) can

be used.

• PSR-E463: L-2C

• PSR-EW410: L-6

When using the L-6 Keyboard Stand

(PSR-EW410)

The exterior size of PSR-EW410 exceeds the limits

as described in the L-6 Assembly Instructions. How-

ever, we have determined through tests that the

stand can be safely used for the instrument. When

setting the instrument, place it on the center of the

stand as shown in the illustration.

• Do not place the instrument in an unstable position where

it might accidentally slip down. This could cause physical

injury to you or others, as well as damage to the instru-

ment or other property.

Place the instrument so

that the left and right parts

of the stand are inside the

protrusions on the bottom

panel of the instrument.

Make sure that the bottom of the

instrument firmly rests on the

stoppers.

CAUTION

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Basic Operation and Display Items

Basic Operation

This instrument features four basic functions: Voice, Style, Song and Groove Creator. To use this instrument,

select a basic function first, and then make various settings.

Press briefly

to increase.

Start a function or play the keyboard.

2 Select an item or value.1 Select a basic function.

Rotate the dial clockwise to

increase the value of the

selected item, or counter-

clockwise to decrease it’s

value.

Dial

Increase

When selecting a Voice, Style,

Groove, Song, etc., you can use

these buttons to jump to the first

item in the next or previous cate-

gory.

These buttons can also be used

to select function items sequen-

tially after pressing the [FUNC-

TION] button.

CATEGORY [<<], [>>] buttons

Use these buttons to directly

enter the desired Style/

Voice number etc, or a

parameter value.

Example:

Selecting Voice 003,

Bright Piano.

Number buttons [0]–[9]

Press the [+/YES] button briefly to

increase the value by 1, or press

the [-/NO] button briefly to

decrease the value by 1. Press

and hold either button to continu-

ously increase or decrease the

value in the corresponding direc-

tion.

Pressing both buttons simultane-

ously lets you reset a parameter

to the default value.

[+/YES], [-/NO] buttons

Decrease

Press briefly

to decrease.

Jumps to

the first

item in the

category.

Press number

buttons [0], [0], [3].

The “Press & Hold” Symbol

Buttons having this indication can be used to call up an alternate function when the relevant

button is pressed and held. Hold down this button until the function calls up.

Depending on the basic function selected in step 1, you can use

the different functions as printed on the panel. Song functions are

printed above the buttons, Groove Creator functions are printed fur-

ther above, and Style functions are printed below.

Jumps to

the first

item in the

next cate-

gory.

* In most procedures described throughout this manual,

the dial is used for selecting items or changing values.

Note however, that in most cases in which the dial can

be used to change values, the [+/YES] and [-/NO] but-

tons can also be used.

Quick Guide

Basic Operation and Display Items

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Display Items

The display shows all the current settings of the Song, Style, Groove, Voice and other related functions.

GrandPno

001

This area indicates the on/off status of

each function. Each indication is

shown when the corresponding func-

tion is turned on.

page 21

page 20

page 22

page 52

page 24

page 53

page 46

page 26

page 60

On/off status

Normally this indicates the

notes you play.

Notation

• Any notes occurring below

or above the staff are indi-

cated by “8va.”

• For a few specific chords,

not all notes may be

shown, due to space limita-

tions in the display.

NOTE

Indicates the source from

which this instrument obtains

power: AC adaptor or batter-

ies (page 15).

Appears when a USB flash

drive is connected to this

instrument (page 71).

Power source status

USB connection status

Indicates the current beat of playback (page 28).

Indicates the parameters and target currently

assigned to the knobs (page 25).

Indicates the Function number when the [FUNC-

TION] button is pressed, or the current Measure

number during playback of a Song, Style or Groove.

Indicates the chord which is being played in the Auto

Accompaniment range (page 26) or specified via

Song playback.

Indicates the on/off status of the current

Song, Style or Groove (pages 29, 38,

60).

Beat

Knob assignment

FUNCTION and MEASURE

Chord

Track status

001

Indicates the assign status of the Sample

feature. When a Sample type is set to

Loop, ( ) is displayed.

Sample Zone status

Indicates that Audio Mode is

enabled, allowing you to play

back or record audio files from/to

a USB flash drive (pages 41, 42).

Indicates that the Quick Sam-

pling mode is enabled, allowing

you to sample sounds from an

external audio device (page 31).

Mode

The illustration is from the PSR-E463.

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Try Playing a Variety of Instrument Voices

This instrument features various instrumental Voices including piano. Not only can you

play just one single Voice (Main Voice), but you can also layer a different Voice (Dual

Voice) to the Main Voice, or play a different Voice (Split Voice) in the left-hand area of the

keyboard from the right-hand area.

Press the [VOICE] button.

The Voice number and name will be shown.

For a list of available Voices, refer to the Voice

List in the separate Data List.

Use the dial to select the desired Voice.

Play the keyboard.

Preset Voice Types

When you want to reset various settings to their

defaults and simply play a Piano sound, press the

[PORTABLE GRAND] button.

The Voice for the entire keyboard will be set to 001

“Grand Piano” (PSR-E463)/ or “Live! Grand Piano”

(PSR-EW410).

In addition to the Main Voice, you can layer a sec-

ond, different Voice over the entire keyboard as a

“Dual Voice.”

Press the [DUAL] button to turn Dual on.

Press the [DUAL] button again to exit

from Dual.

Although turning on Dual will select a Dual Voice

suitable for the current Main Voice, you can also

select a different Dual Voice (page 55).

Selecting a Main Voice

• Voice number 001 on the PSR-EW410 is “Live! Grand

Piano.”

001–237 Instrument Voices.

238–261

(Drum/SFX Kit)

Various drum/percussion or SFX sounds are

assigned to individual keys. Details on assigning

instruments to keys are provided in the Drum/

SFX Kit List of the separate Data List.

262–301 Used for Arpeggio performance (page 22).

302–758 XGlite Voices.

759 Sample Voice.

000

Selecting this automatically calls up the most

suitable Voice and panel setups for the current

Style, Song or Groove. This function is called

OTS (page 51).

GrandPno

001

Voice name

Voi ce number

NOTE

Flute

137

Playing the “Grand Piano”

Layering a Dual Voice

Two Voices will

sound at the same

time.

Appears when Dual

is on

Try Playing a Variety of Instrument Voices

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

By dividing the keyboard into the two separate areas,

you can play a different Voice between the Left hand

and Right hand areas.

Press the [SPLIT] button to turn Split on.

The keyboard is divided into left and right hand

area at the Split Point. You can play a Split Voice

on the left hand area while playing a Main Voice

and Dual Voice on the right hand area of the key-

board.

The Split Voice (page 55) and the Split Point can

be changed as desired (page 62).

Press the [SPLIT] button again to exit

from Split.

This instrument features a built-in metronome which

can be used when practicing.

Press the [METRONOME] button to start

the metronome.

Press the [METRONOME] button again to

stop the metronome.

Adjusting the Metronome Tempo

This operation lets you adjust not only the metro-

nome tempo, but also the tempo of Style, Song and

Groove.

Press the [TEMPO/TAP] button to call up

“Tempo.”

The current tempo is shown on the display.

Adjust the tempo by rotating the dial.

Setting the Time Signature

This operation lets you change the time signature

from the default value. In this example, we’ll set a

time signature of 6/8.

Hold down the [METRONOME] button for

longer than a second to call up “Time-

SigN” (Time Signature Numerator).

The number of beats per measure is shown on

the display.

Playing a Split Voice in the Left

Hand area

Appears when Split

is on

Split Voice

Main Voice (and Dual Voice)

Split Point ... default value: 054 (F#2)

036

(C1)

048

(C2)

060

(C3)

072

(C4)

084

(C5)

096

(C6)

Using the Metronome

Tempo

090

Current tempo

TimeSigN

Number of beats

per measure.

Hold for longer

than a second.

Try Playing a Variety of Instrument Voices

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Rotate the dial to select the number of

beats per measure.

A chime will sound on the first beat of each mea-

sure while a click sounds the other beats. If “0” is

selected, a click sounds for all beats with no

chime accent. Select 6 for this example.

Press the CATEGORY [>>] button once

to call up “TimeSigD” (Time Signature

Denominator).

The length of one beat is shown on the display.

Rotate the dial to select the length of

one beat, from 2

, 4

, 8

and 16

note

values.

Select “08” (8

note) for this example.

Confirm the setting by playing the Metro-

nome.

Setting the Metronome Volume

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “MtrVol” (Function 060).

Rotate the dial to set the volume.

Yo u can add effects such as Harmony, Tremolo and

Echo to the Main Voice. For a list of the effects, refer

to the Harmony Type List in the online material Data

List.

Press the [HARMONY/AGPEGGIO] but-

ton to turn Harmony or Arpeggios on.

The HARMONY or ARPEGGIO icon appears on

the display and the Harmony effect or the Arpeg-

gio function are turn on.

Although turning on the Harmony or the Arpeggio

will select a Harmony type or an Arpeggio type

suitable for the current Main Voice, you can

select a different Harmony type or Arpeggio type

(page 23).

Press a note or notes to add a Harmony

or trigger an Arpeggio.

The operation differs depending on the Harmony

type. Try playing the keyboard by referring to

“Playing each Harmony Type” (see next page),

and the Harmony Type List on online material

Data List.

The Arpeggio phrase differs depending on the

number of pressed notes and the area of the key-

board.

Press the [HARMONY/ARPEGGIO] but-

ton again to turn the Harmony or Arpeg-

gio off.

• This parameter cannot be set during playback of a Style,

Song or Groove.

NOTE

TimeSigD

The length of

one beat.

MtrVol

100

060

Metronome volume

Adding Harmony/Triggering

Arpeggios

Appears when the Har-

mony function is on.

Appears when the

Arpeggio function is on.

Try Playing a Variety of Instrument Voices

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Hold down the [HARMONY/ARPEGGIO]

button for longer than a second.

After “Harm/Arp” (Function 041) appears on the

display, the current Harmony type or Arpeggio

type appears.

Rotate the dial to select the desired Har-

mony type or Arpeggio type.

Adjusting the Harmony Volume

Yo u can adjust the Harmony volume in the Function

Settings (page 68, Function 042).

Adjusting the Arpeggio Velocity

Yo u can adjust the Arpeggio velocity in the Function

Setting (page 68, Function 043).

• When Split (page 21) is on, Arpeggio is applied only to

the Split Voice. When Split is off, Arpeggio is applied to

the Main and Dual Voices. Arpeggio cannot be applied to

the Split and Main/Dual Voices simultaneously.

• Selecting a Voice number between 292 and 301 will turn

on Split automatically, as well as Arpeggio. When one of

those Voices is selected, Arpeggio is applied only to the

Split Voice and is triggered only by playing a key to the

left of the Split Point.

• By assigning the Arpeggio Hold function to the foot-

switch, the Arpeggio will continue to play after the note is

released (page 68).

Playing each Harmony Type

• Harmony types 01 to 05

• Harmony types 06 to 12 (Trill)

• Harmony types 13 to 19 (Tremolo)

• Harmony types 20 to 26 (Echo)

NOTE

Press the right-hand keys while playing chords in

the Auto Accompaniment area of the keyboard

when ACMP is on (page 26).

Hold down two keys.

Keep holding down

the keys.

Play the keys.

Changing the Harmony and

Arpeggio types

• 001 to 026 are Harmony types. 027 to 176 are Arpeggio

types. Refer to the Harmony Type List / Arpeggio Type

List on web material Data List.

• When playing one of the Arpeggio types 143 or later,

select a Drum Kit (Voice No.238–261) as the Main Voice.

Trio

002

041

Harm/Arp

041

Current Harmony type or

Arpeggio type

Hold for longer

than a second.

NOTE

Try Playing a Variety of Instrument Voices

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

DSP is an abbreviation for Digital Signal Processor,

and provides effects that enhance the sound. DSP

effects are applied only to a specified target as

described below.

Parts to which DSP effects are applied

Press the [DSP] button to turn DSP on.

Although turning on DSP will select a DSP type

suitable for the current panel setting, you can

select a different DSP type as described in the

following steps.

Hold down the [DSP] button for longer

than a second to call up “DSP Type”

(Function 040).

After a few seconds, the current DSP type

appears.

Rotate the dial to select a DSP type.

For information about the available DSP types,

refer to the Effect Type List in the Data List.

Press [KNOB ASSING] button to select

Press the [TARGET] button and select

the target.

When KEYBOARD is selected, the DSP affects

the Main Voice, Dual Voice or track 1 of a User

Song. When BACKING is selected, it affects the

Style, Groove Creator or track A of a User Song.

Press the [DSP] button again to turn DSP

off.

Adding DSP Effects

target: KEYBOARD

• Main Voice

• Dual Voice

• Track 1 of a User Song

 When selecting the target “KEYBOARD” for DSP

DSP

• ON/OFF

• Type

target: BACKING

• Style

• Pattern

• Track A of a User Song

 When selecting the target “BACKING” for DSP

Output

target: KEYBOARD

• Main Voice

• Dual Voice

• Track 1 of a User Song

DSP

• ON/OFF

• Type

target: BACKING

• Style

• Pattern

• Track A of a User Song

• This parameter is set in step 5.

Appears when

the DSP is on.

DSP Type

040

RotarySp

040

Current DSP type

Hold for longer

than a second.

Limitations when recording a Song

• DSP effects can be recorded only to Tracks 1 and

• The DSP type and target cannot be changed

while recording.

• When recording to an existing User Song, if the

target to which the DSP effects are applied differs

from the recording tracks, DSP related setting

data (DSP target, type, parameter A/B) will not be

recorded or overwritten.

• The DSP effects may not be applied as expected

when a User Song is being played back. This is

because the DSP effects are affected by the data

recorded to the User Song.

GrandPno

001

Current Target

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Creating Original Sounds via the Knobs

The two knobs can be used to add variations to the sound being played, transforming

the sound in a variety of musical ways. Select the desired pre-programmed function

combination printed above the knobs, then rotate the knobs as you play, for an expres-

sive, dynamic performance.

Repeatedly press the [KNOB ASSIGN] button to

sequentially assign the function combinations pro-

vided: z  x  c  v  b  z … etc. The cur-

rent combination is shown in the display.

The target differs depending on the selected number.

For details about each function, refer to page 57.

Press the [TARGET] button to switch the target con-

trolled with the knobs. The current target is shown in

the display.

• KEYBOARD: Main Voice, Dual Voice and User

Song (only Function 3)

• BACKING: Style, Groove and User Song (only

Fu nction 3)

Here is an example of how to use the knobs. For some

other ideas for using the knobs, refer to page 58.

Select the desired Main Voice (page 20).

Here, select Voice No.156 “SquareLD” (Square

Lead) as a synth-lead type Voice.

Press the [KNOB ASSIGN] button sev-

eral times until z appears in the display.

Press the [TARGET] button to switch the

target to KEYBOARD.

Rotate knob B all the way to the right

(maximum), then play the keyboard with

your right hand while operating the knob

A with your left.

Assigning Functions to the

Knobs

Function Target

1 CUTOFF/RESONANCE

Main Voice, Dual Voice, Style and

Groove

2 REVERB/CHORUS

3DSP

Main Voice, Dual Voice, Style,

Groove and User Song

4 ATTACK/RELEASE Main Voice and Dual Voice

VOLUME BALANCE/

RETRIGGER RATE

Knob A: Audio input from the exter-

nal device, and Style/

Groove/Song

Knob B: Groove

• Only selecting a function combination will not affect the sound

even if the knob arrow is not at the center position. The

selected function only works when the knob is moved.

• Depending on the panel settings or how you move the knob,

you may not notice any change to the parameter value, or you

may hear a noise, or the knob may not work properly, even if

you rotate it.

Switching the Target

GrandPno

001

Current function

NOTE

• The target differs depending on the selected function.

• The target is memorized for each function.

Using the Knobs

• After selecting z, x or c by pressing the [KNOB

ASSIGN] button, changing the Voice will replace the

settings created via the knobs with the default settings

of the new Voice.

If you want to keep the settings you have created,

make sure to memorize it to Registration Memory

(page 44) before selecting a different Voice.

• Rotating a knob to the right while the volume is set to a

high level may result in distortion. If this occurs, reduce

the volume level.

NOTE

CUTOFF RESONANCE

NOTICE

NOTE

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Playing Styles

This instrument includes an Auto Accompaniment feature that plays appropriate

“Styles” (rhythm + bass + chord accompaniment). You can select from a huge variety of

Styles covering a wide range of musical genres.

Press the [STYLE] button, then use the

dial to select the desired Style.

For the Style List, refer to the online material

Data List.

Press the [ACMP ON/OFF] button to turn

on the Auto Accompaniment (ACMP).

With this operation, the area of the keyboard to

the left of the Split Point becomes the “Auto

Accompaniment area” and is used only for speci-

fying the chords. The rhythm part as well as the

bass and chord accompaniment play back when

you play chords.

The Split Point can be changed as desired (page

62).

Press the [SYNC START] button to turn

Synchro Start on.

This puts the Style playback in “standby” and

Style starts playing back when you play the key-

board.

Play a chord in the Auto Accompaniment

area to start playback.

Play a melody with the right hand and chords

with the left hand.

Press the [START/STOP] button to stop

playback.

Yo u can easily add variations to your perfor-

mance by changing the section of the Style. For

details, refer to page 59.

• Press the CATEGORY [<<][>>]button to change the musi-

cal genre. Refer to the Style List at the top of the panel.

BritRock

001

Style Name

Style Number

NOTE

Appears when the Auto

Accompaniment is on.

Auto Accompa-

niment area

Split Point ... default value: 054 (F#2)

036

(C1)

048

(C2)

060

(C3)

072

(C4)

084

(C5)

096

(C6)

• For information about how to play chords, refer to page

63.

EuTrance

062

Flashes when sync

start is on.

Split Point

NOTE

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Playing Songs

This instrument can play Preset Songs, Songs you recorded on this instrument, or

commercially available Songs. In addition to listening to these Songs, you can play the

keyboard along with the Song as it plays back.

MIDI Data

A MIDI Song is comprised of your keyboard performance information and is not a recording of the actual sound

itself. The performance information refers to which keys are played, at what timing, and at what strength—just

as in a musical score. Based on the recorded performance information, the tone generator (of the Clavinova,

etc.) outputs the corresponding sound. A MIDI Song uses a small amount of data capacity in comparison to an

Audio song, and allows you to easily change aspects of the sound, such as Voices used, etc.

 Song Category

The Songs are organized by category as listed below.

• For details on Audio playback and recording, refer to page 42.

• In addition to the 30 preset Songs in this instrument, you can enjoy extra Songs downloadable from the Yamaha website. For details,

refer to page 11.

• For instructions on transferring Songs from a computer to this instrument, refer to the online PDF manual (page 11) “Computer-related

Operations.”

The numbers are generally assigned to the Songs in the following sequence: Songs transferred from a computer, Songs in the USB

flash drive. When you transfer a Song from a computer while the USB flash drive is connected to the instrument, the transferred Song

will be inserted before the first USB Song number, moving all USB Song numbers later in sequence.

NOTE

•Gives you an idea of the advanced capabilities of this instrument.

• Demonstrates many useful Voices of this instrument.

•Enjoyable piano solo performances.

• These songs are piano ensemble pieces. Enjoy the sound of piano and orchestra.

•Enjoyable piano accompaniment in a variety of genres.

• Songs you’ve record yourself (page 38).

• FLASH MEMORY: Songs transferred from a computer (page 47).

• USB: Songs in the USB flash drive (page 70).

NOTE

Playing Songs

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Press the [DEMO] button to play Demo Songs 001–

003 in sequence. Playback will repeat continuously,

starting again from the first Song (001).

To s to p p lay back, press the [DEMO] or [ ] (Start/

Stop) button.

Hold down the [DEMO] button for longer than a sec-

ond to use the instrument as a background music

source (page 64).

Press the [SONG] button, then rotate the

dial to select the desired Song.

For a list of available Songs, refer to the Song List

in the separate Data List.

Yo u can select User Songs, Songs transferred

from a computer, and Songs in the USB flash

drive in the same way as above.

Press the [ ] (Start/Stop) button to

start playback.

To s to p p lay back, press the [ ] (Start/Stop)

button again.

Listening to a Demo Song

Selecting and Playing Back a

Song

• The selectable Songs are number 4 and later. When

selecting the number 1 to 3, press [DEMO] button.

NOTE

Jeanie

013

Song name

Song number

Each arrow mark flashes in

time with the beat.

Jeanie

013

001

Current

measure

• External MIDI Songs containing Portamento Control and

Scale Tune settings may not be played correctly.

• If playback of a Song in the USB flash drive or a Song

transferred from a computer produces distorted sound,

decrease the Song volume (page 65) to reduce the dis-

tortion, and then adjust the master volume (page 16).

Song Fast Forward, Fast

Reverse, and Pause

• When the A-B repeat is specified, the Fast Reverse and Fast

Forward will only work within the range between A and B.

• The [ ], [ ] and [ ] buttons cannot be used for Demo

Song playback started by using the [DEMO] button.

NOTE

[] Fast Reverse

During playback,

press this button to

rapidly return to an

earlier point in the

Song.

[ ] Fast Forward

During playback, press this but-

ton to rapidly skip ahead to a

later point in the Song.

[] Pause

During playback,

press this button to

pause playback, and

press again to start

from that point.

NOTE

Playing Songs

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Yo u can play back only a specific section of a Song

repeatedly by setting the A point (start point) and B

point (end point) in one-measure increments.

Start playback of the Song (page 28).

When playback reaches to the point you

want to specify as the start point, press

the [ ] (A-B REPEAT) button to set

the A point.

When playback reaches to the point you

want to specify as the end point, press

the [ ] (A-B REPEAT) button again

to set the B point.

The specified A-B section of the Song will now

play repeatedly.

To cancel repeat playback, press the

[ ] (A-B REPEAT) button again.

To s to p p lay back, press the [ ] (Start/Stop)

button.

Each “track” of a Song plays a different part—mel-

ody, percussion, accompaniment, etc. Each of the

tracks can be muted so that you can play the muted

part yourself. Pressing the desired Track button

repeatedly will toggle the on/off status.

The status of each track is shown in the display.

Playing a Specified Section of a

Song Repeatedly (A-B Repeat)

• If you want to set start point “A” to the top of the Song,

press the [ ] (A-B REPEAT) button before starting

playback.

• If you want to set end point “B” to the end of the Song,

specify only the A point and play back the Song to the

end.

NOTE

Turning Each Track On/Off

• Up to two Track buttons can be pressed simultaneously for

turning on or off.

Tra ck number off—Track is

muted or contains no data

Tra ck number on—Track

will be played back

NOTE

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Playing with Groove Creator

The Groove Creator function lets you repeatedly play back various rhythm patterns and

phrases (each called a Groove) in various genres, including Hip Hop, House, etc.—for

dynamic, powerful performances. Try out the expressive performance features, such as

changing keys in the left-hand area of the keyboard and rotating the knobs for dynamic

sound variations.

Press the [GROOVE CREATOR] button,

and use the dial to select the desired

Groove.

ACMP is automatically turned on, and the key-

board is divided into the Auto Accompaniment

area (page 26) and melody area.

Press the [ ] (Start/Stop) button to

start Groove playback.

Yo u can also start playback by pressing any note

in the Auto Accompaniment area (page 26).

During Groove playback, enjoy creating sound

variations via the following operations.

 Turni ng on/off individual tracks via the

[TRACK CONTROL] buttons

 Changing the Section via the [A]–[D] but-

tons

 Using the [MUSICAL CLIMAX] button

When you press the button, a negative count (indi-

cating a lead-in) appears on the display. As the lead-

in approaches 0, the Groove builds in intensity and

variation. When the count reaches 0, it comes to a

musical climax. You can use this as professional

sounding build-up, switching to another section or

another Groove when the count reaches 0 (or even

before, if you want). Moreover, this can also be used

as an Ending; the Groove stops after the count

reaches 0 and an Ending phrase is played.

 Using the Retrigger function

Groove Retrigger is a function which repeats

the first part of the current Groove, for a rhyth-

mic break effect. For details, refer to page 61.

 Transposing playback by pressing any note

in the Auto Accompaniment area (page 26).

 Changing the sound via the Knobs

Press the [KNOB ASSIGN] button several times

to select the function. Press [TARGET] button and

BACKING icon appears on the display, then

rotate knobs A and B. Refer to page 25.

 Playing Arpeggios in the right-hand area

Press the [ARPEGGIO] button to turn it on, and then

play the notes in the right-hand area of the keyboard.

Press the [ ] (Start/Stop) button to

stop playback.

• To select a genre, use the CATEGORY

[<<][>>] buttons. Refer to the right

side at the top of the panel.

• Refer to online material Data List.

• Up to two track buttons can be pressed simultane-

ously for turning on or off.

Elec Dnc

001

Flashes

NOTE

On/off status is shown in

the display (page 19)

NOTE

• When you select a Voice between 292 and 301,

Arpeggio is applied only to the Split Voice. Playing a

key to the left of the Split Point turns Arpeggio on as

well as specifies the key for Groove playback.

SECT B

Split Point

Specified key

NOTE

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Playing with Quick Sampling

This instrument features an extremely convenient and powerful Quick Sampling func-

tion. It allows you to sample sounds from an external audio device (such as a computer,

smartphone, portable music player, etc.) via the [AUX IN] jack, and then assign the sam-

pled sound to the keyboard for playing back as part of your performance.

Sampling

Sampling is a technology that lets you record a short portion of a song or a sound, and use the sound (called a

“sample”) as part of your performance. Unlike Audio Recording, the samples can be used in various ways: to

play a melody, to play in a loop for a repeating rhythm pattern, or to add a special sound effect.

A wide variety of samples are already built into this

instrument as presets. Try playing them and see how

powerful the sampling features are!

Press the [VOICE] button.

Use the dial to select the Voice number

759 “Sampling” for the Main Voice.

Press the keys in the Sample Zone to

which the default samples are assigned

to play back the samples.

Sample Zone

The keyboards of the two instruments are divided

into five or seven Sample Zones and each Zone

has one assigned sample.

Sample Type

By default, a “Normal” type sample is assigned to

Sample Zone A, “Loop” types are assigned to B

and C, and “One-shot” types are assigned to D–

G. However, when you sample by yourself, you

can freely choose “Loop” or “One-shot” types for

Sample Zones B–G.

 Normal: The pitch of the sound varies depend-

ing on the key you play. The default pitch is

assigned to the note C3.

 Loop: The sample is played in a loop without

changing the pitch. Pressing a white key in

the Sample Zone plays the sample as long

as you are holding it, while pressing a black

key plays the sample continuously until you

press a black key in the same Sample Zone

to stop it. When the type is “Loop,”

appears on the display for the corresponding

Sample Zone.

 One-shot: The sample is played only once

without changing the pitch. The sample is

played continuously as long as you hold any

key in the Sample Zone.

Set the volume levels to minimum for

both this instrument and the external

device.

Connect the headphone jack of an exter-

nal device to the instrument’s [AUX IN]

jack by using an audio cable.

Playing back the Samples

Smpl Vce

759

Sample Zone A

Normal

BECD

Loop/

One-shot

PSR-E463

Sample Zone A

Normal

BECD

Loop/

One-shot

PSR-EW410

Getting Ready for Sampling

• Connecting an external device to the instrument with-

out turning down the volume may result in damage to

the device.

• To avoid damage to the devices, first turn on the power

to the external device, and then to the instrument.

When turning off the power, first turn off the power to

the instrument, and then to the external device.

NOTICE

Playing with Quick Sampling

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Start playback on the external device,

and then adjust the volume balance

between the device and the instrument.

3-1 Set the volume of the external device to max-

imum.

3-2 Adjust the volume you hear from the instru-

ment by rotating the [MASTER VOLUME]

control.

Up to five (on the PSR-E463) or seven (on the PSR-

EW410) samples can be assigned to the keyboard of

this instrument. The samples can also be saved to a

USB flash drive (page 34).

Press the [QUICK SAMPLING] button to

enter the Quick Sampling mode.

The SAMPLING icon and “PressKey” appear on

the display.

Press a key in the desired Sample Zone

to which the sample is to be assigned.

Pressing the key will sound the default sample or

previously assigned sample.

 To sample a “Normal” type:

2-1 Press one of the keys in Sample Zone A.

When “PressREC” appears on the display, go

on to step 3.

 To sample a “Loop” or “One-shot” type:

2-1 Press one of the keys in the desired Sample

Zone (B–E on the PSR-E463, and B–G on

the PSR-EW410).

Sample Zone B: C5–D5

Sample Zone C: D# 5–F#5

Sample Zone D: G5–A5

Sample Zone E: A#5–C6

Sample Zone F: D6–E6

Sample Zone G: F6–G6

• When the sound is too low even though the external

device’s volume is set to maximum, adjust the “AuxIn Vol”

in the Function Settings (page 66, Function 004). If you

increase the volume to more than 50, the audio device

sound may be distorted. In this case, turn down the vol-

ume level on the external device.

Sampling External Audio Sound

Before you start sampling, make sure that the external

device’s volume is set to maximum. If the volume is too

low, the instrument cannot sample the sound.

• The sampling operation will overwrite and erase previously

existing samples. Save important data you want to keep to

a USB flash drive (page 34).

• The sampling format is two-channel stereo, 16-bit with a rate

of 44.1 kHz.

• If you want to use the metronome or Melody Suppressor

when sampling, set these functions beforehand. The Metro-

nome click is not sampled.

Stereo mini plug

Headphone

jack

Audio cable

Stereo mini plug

NOTE

NOTICE

NOTE

• To cancel and exit from the Quick Sampling mode, press

the [QUICK SAMPLING] button again.

NOTE

Sample Zone A: C1–B4

PSR-E463

Sample Zone A: E0–B4

PSR-EW410

Sample

Zone

BECD

PSR-E463

Sample

Zone

PSR-EW410

BECD FG

Playing with Quick Sampling

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

2-2 When “Loop?Y/N” appears on the display,

press the [+/YES] button to select “Loop”

sampling, or press [-/NO] to select “One-

shot” sampling. You cannot change the type

after sampling.

When “PressREC” appears on the display, go

on to step 3.

Pause playback on the external device at

the beginning of the sound or phrase

you want to sample.

Press the [REC] button, and then start

playback on the external device to start

sampling.

While sampling the sound, “REC” appears and

glowing icon of selected the Sample Zone on the

display.

Do not disconnect the USB flash drive during the

sampling operation. The operation may b ecome

unstable, and sampling may not be performed

properly.

Stop playback on the external device at

the end of the sound or phrase you want

to sample.

Press the [REC] button to stop sampling.

“Writing!” appears briefly on the display, and then

the sample is stored to the instrument.

Check if the sample is assigned suc-

cessfully.

For “Normal” types, press the C3 key. For “Loop”

and “One-shot” types, press any one key in the

Sample Zone to which you assigned the sample.

Any silence at the beginning and end of the sam-

ple can be automatically cut by the Blank Cut

function (page 69).

If you are not satisfied with the sample, return to

step 2 and try sampling again.

To sample and assign to another Sample Zone,

go on to step 2 again.

Press the [QUICK SAMPLING] button to

exit from the Quick Sampling mode.

Try playing the samples.

Exiting from the Quick Sampling mode automati-

cally selects the Voice number 759 “Smpl Vce”

for the Main Voice. Try playing it on the keyboard.

• If the input volume from the external device is too low,

“LowInput” appears on the display and cannot sample

the sound. Raise the external device’s volume to maxi-

mum, and then adjust the output volume on this instru-

ment by rotating the [MASTER VOLUME] control. After

that, try sampling again from step 3.

• Sampling time is limited to a maximum of 9.6 seconds.

When the time limit is reached, sampling stops automati-

cally and the recorded sample (up to that point) is stored

to the instrument.

Sampling

pEC

NOTE

To avoid damage to the external device, disconnect the

device in this way:

1 Set the volume levels to minimum for both this instrument

and the external device.

2 Disconnect the audio cable from the instrument, and

then from the external device.

To sample during audio playback

Once you are familiar with the sampling operation,

try starting and stopping sampling while the sound

of the external device is playing back.

1. E x e c ute steps 1–2 in “Sampling the External

Audio Sound” on page 32.

2. Pause playback on the external device at a few

measures before the sound or phrase you want

to sample.

3. Start playback on the external device.

4. Press the [REC] button at the desired point to

start sampling.

5. Press the [REC] button again at the desired

point to stop sampling.

6. Stop playback on the external device, and then

check what you have just sampled.

NOTICE

• If there is silence in the audio that is cut automatically but

you want to keep it, turn off the Blank Cut function (page

69).

NOTE

Playing with Quick Sampling

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

This operation lets you restore the default samples.

However, keep in mind that this deletes the samples

you’ve assigned to each Sample Zone. If you want to

save your samples before restoring the default ones,

see the next section (“Saving Samples to a USB

Flash Drive”).

Press the [QUICK SAMPLING] button to

enter the Quick Sampling mode.

Press the appropriate key in the Sample

Zone to which the sample to be cleared

has been assigned.

Hold down the TRACK CONTROL

[STYLE] button for longer than a second.

A confirmation message will appear on the dis-

play.

Press the [+/YES] button.

A confirmation message will appear on the dis-

play. To cancel this operation, press the [-] button.

Press the [+/YES] button to clear the

Sample.

An in-progress message will appear briefly on the

display.

Confirm the Sample Zone containing the

sample you intend to save.

1-1 Press the [VOICE] button.

1-2 Select the Voice number 759 “Sampling” for

the Main Voice.

1-3 Press the key to confirm that the desired

sample sounds.

Connect a USB flash drive to the [USB

TO DEVICE] terminal.

For details, refer to “Connecting a USB Flash

Drive” on page 71.

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

To cancel the operation, press the [FUNCTION]

button again to exit from the File Control display.

Use the CATEGORY [<<] and [>>] but-

tons to call up “SaveSMPL.”

Press the [0/EXECUTE] button.

“PressKey” appears on the display.

Press the appropriate key in the Sample

Zone (the key to which the desired sam-

ple is assigned).

Use the [+/YES] and [-/NO] buttons to

select the file name for saving.

• Normal/One-shot: SMPL001–SMPL250

• Loop: SMPLL001–SMPLL250

Press the [0/EXECUTE] button.

“SaveOK?” appears on the display.

Press the [0/EXECUTE] button again.

“Saving” appears on the display and the sample

will be saved to the USB flash drive.

Press the [FUNCTION] button to exit

from the File Control display.

Restoring the Default Samples

Saving a Sample to a USB Flash

Drive

• If the instrument is in the Quick Sampling mode, press the

[QUICK SAMPLING] button to exit from the mode, and then

follow the steps below.

ClrSMPL?

IMPORTANT

• If the file name already exists in the USB flash drive,

“Overwr?” appears on the display. To overwrite, press the

[+/YES] button; to select another name, press the [-/NO]

button.

SaveSMPL

NOTE

Playing with Quick Sampling

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Connect a USB flash drive to the [USB

TO DEVICE] terminal.

For details, refer to “Connecting a USB Flash

Drive” on page 71.

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

To cancel the operation, press the [FUNCTION]

button again to exit from the File Control display.

Use the CATEGORY [<<] and [>>] but-

tons to call up “LoadSMPL.”

Press the [0/EXECUTE] button.

“PressKey” appears on the display.

Press the appropriate key in the Sample

Zone to which you want to assign the

sample.

Use the [+/YES] and [-/NO] buttons to

select the file name to load.

You cannot select a sample that loops

(SMPLL001–SMPLL250) for assigning to Sample

Zone A.

Press the [0/EXECUTE] button.

“LoadOK?” appears on the display.

Press the [0/EXECUTE] or [+/YES] button

again.

“Loading” appears on the display and the sample

will be saved to the USB flash drive.

Press the [FUNCTION] button to exit

from the File Control display.

Try playing with the loaded samples.

Press the [VOICE] button and select the Voice

number 759 “Smpl Vce” for the Main Voice.

Pressing the appropriate key in the Sample Zone

(to which you assigned the sample) to play the

sound.

Connect a USB flash drive to the [USB

TO DEVICE] terminal.

For details, refer to “Connecting a USB Flash

Drive” on page 71.

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

To cancel the operation, press the [FUNCTION]

button again to exit from the File Control display.

Use the CATEGORY [<<] and [>>] but-

tons to call up “Del SMPL.”

Press the [0/EXECUTE] button.

Use the [+/YES] and [-/NO] buttons to

select the file name to delete.

Press the [0/EXECUTE] button.

“Del OK?” appears on the display.

Press the [0/EXECUTE] or [+/YES] button

again.

“Deleting” appears on the display and the sample

is deleted from the USB flash drive.

Press the [FUNCTION] button to exit

from the File Control display.

If the instrument is in the File Control display, no

sound comes out even if you press the keyboard.

Loading a Sample from a USB

Flash Drive

• If the instrument is in the Quick Sampling mode, press the

[QUICK SAMPLING] button to exit from the mode, and then

follow the steps below.

• The loading operation will overwrite and erase previously

existing samples. Save important data you want to keep to

a USB flash drive (page 34).

IMPORTANT

NOTICE

LoadSMPL

Deleting a Sample in the USB

Flash Drive

• If the instrument is in the Quick Sampling mode, press the

[QUICK SAMPLING] button to exit from the mode, and then

follow the steps below.

IMPORTANT

Del SMPL

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Playing Like a DJ!

The dynamic Groove Creator function and Live Control Knobs give you powerful tools

to sound just like a pro DJ! Since the Grooves and section variations change seam-

lessly without breaks in the rhythm, performing is truly easy. Still, a sense of rhythm is

important. So, turn up the volume, feel the rhythm in your body, and work the buttons

and knobs—as if you were in front of the dance floor!

In this example using Groove number 001 (Elec Dnc.), you’ll learn how to take one

Groove and transform it in a variety of ways.

Press the [GROOVE CREATOR] button,

and select Groove 001 with the dial or

number buttons.

Use the [TRACK CONTROL] buttons to

turn on tracks [1], [2] and [3], and turn off

tracks [4], [5] and [6], so that only the

rhythm plays back.

Press the section [A] button to play back

Section A (shown as “SECT A” in the

display).

Press the [ ] button to start play-

back.

While checking the Beat marks “ ”

and Measure number as they change on

the display, wait until the fourth beat of

Measure 008 (just before Measure 001

starts again), and then press the track

[6] button to turn on track [6].

With the same timing as in step 5, simul-

taneously press the track [4] and [5] but-

tons to turn on tracks [4] and [5].

While checking the Beat marks “ ”

as they change on the display, press the

section [B] button at a musically appro-

priate time to switch to Section B.

Even if your timing is slightly off, the section will

naturally change in time with the rhythm.

With the same timing as in step 1, press

the section [C] or [D] button to build up

the Groove.

While checking the display, press the

[KNOB ASSIGN] button several times (as

needed) to select z.

While checking the display, press the

[TARGET] button once or twice to select

BACKING.

Rotate knob A fully to the right, and then

rotate knob B fully to the left.

Rotate knob A slowly to the right to

change the muffled sound to a clear,

bright sound. Move it slowly in time with

the rhythm.

Creating an

Intro Part

Building

Excitement

and Interest

Adding

Effects

Creating

Greater

Excitement

Switching to

Another

Groove

Creating an Intro Part with the

Track On/Off Controls

• Only up to two tracks can be turned on and off at the

same time, so press only two buttons.

Elec Dnc

001

SECT A

008

NOTE

Building Excitement and

Interest by Changing Sections

Adding Effects to the Groove

with the Live Control Knobs

SECT C

Playing Like a DJ!

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Now try rotating knob A back and forth

slowly with the rhythm. Notice that you

can get a completely different sound and

feel, even with the same rhythmic

phrase.

As in the steps above, press the [KNOB

ASSIGN] button and try using the sec-

ond and third items. REVERB/CHORUS

controls the acoustic ambience, or pro-

duces a rich and warm layered effect.

DSP controls one of 10 different effects,

such as rotary speaker and distortion.

For details, refer to page 57.

Press the section [C] button to switch to Section C

and listen to the rhythm. The beats become increas-

ingly more rapid after the Measure 005, and this

effect creates intensity and excitement. You can raise

the emotional level of your own performance with a

similar “rapid-fire” effect with the Retrigger function

and Live Control Knobs.

While checking the display, press the

[KNOB ASSIGN] button several times to

select b.

Rotate knob B about 90° to the left.

While checking the Beat marks “ ”

and Measure number in the display,

press and hold the section [C] button at

the point just before the Measure count

reaches 005.

While holding down the section [C] but-

ton, rotate knob B according to the fol-

lowing illustration. The beats become

more rapid according to the knob posi-

tion.

Release the section [C] button at the

dynamic peak to return to normal play-

back of the Groove .

While checking the Beat marks “ ”

on the display, press the [MUSICAL CLI-

MAX] button at an appropriate timing,

just before when the Measure changes

from 008 back to 001. The Groove starts

building to a climax with an 8-measure

lead-in (negative count).

Just as the lead-in approaches 0, use the

number buttons to enter a different

Groove number. The timing may be a lit-

tle difficult, but with practice you can

seamlessly switch to another Groove

after the Musical Climax—just like a pro

DJ!

• When switching the [LIVE CONTROL] row, make sure to

set the target to BACKING. The target is conveniently

saved for each function.

• When using c, press the [DSP] button to turn on the DSP

function. The DSP icon appears on the display.

• Only selecting a function combination will not affect the

sound even if the knob arrow is not at the center position.

The selected function only works when the knob is

moved.

Creating Greater Excitement

with the Retrigger Function

NOTE

SECT C

008

Switching to Another Groove

with Musical Climax

• By memorizing the next Groove to a Registration Memory

setting, you can easily switch Grooves with just a single

button press (page 44).

M.Climax

−08

NOTE

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Recording Your Performance

You can record up to 10 of your performances to the instrument as User Songs. The

recorded User Songs can be played back in the same way as the preset Songs.

A Song can be recorded to the six tracks. You can

record without specifying tracks, but you can also

record each track one by one (e.g., only the right-

hand part or the left-hand part) to create a complete

piece which may be difficult to play at once.

 Melody Tracks [1/RIGHT]–[5]

These are for recording melody or similar perfor-

mances.

 Accompaniment Track [A]

This is for recording a chord progression (for the

Style) or key changes (for the Groove).

This section explains how to record without specify-

ing a track. This is useful when recording a new

Song from scratch.

Make the desired settings including the

Main Voice selection.

Make the desired settings for recording

your performance.

• If you want to record only the melody perfor-

mance, press the [SONG] button.

• If you want to record the performance using a

Style, press the [STYLE] button.

• If you want to record the performance using a

Groove, press the [GROOVE CREATOR] but-

ton.

Press the [REC] button to enter the

Record Ready mode.

This operation selects the lowest-numbered

unrecorded User Song from 031–040 (User 1–

10) as the recording target.

Track 1 will be selected as recording target of the

melody, and the Track A will be selected as

recording target of the accompaniment part (the

chord progression for the Style or the key change

for the Groove) automatically. If a User Song was

selected beforehand, recording data will overwrite

Tracks 1 and A of the selected Song.

To exit from this status, press the [REC] button

again.

Start recording.

• When you press the [SONG] button in step 2,

play any note to start recording.

• When you select a Style in step 2, play a chord

in the Auto Accompaniment area to start

recording with Style playback, or press the

[ ] (Start/Stop) button to start recording

with playback of only the Rhythm part of a

Style.

• When you select a Groove in step 2, play a key

in the Accompaniment area or press the

[ ] (Start/Stop) button to start recording

with Groove playback.

The current measure will be shown on the display

while recording.

• For details on Audio recording, refer to page 42.

• This instrument records your performance and saves it in an original format. If you want to save it as MIDI data, convert it to SMF by

saving it to the connected USB flash drive (page 73).

NOTE

Track Structure of a Song

Quick Recording

Melody Tracks

Accompani-

ment Track

• The ACMP on/off status cannot be changed after the

[REC] button is pressed.

User 1

001

pEC

Flashes

NOTE

User 1

003

pEC

Current measure

number

Recording Your Performance

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Press the [ ] (Start/Stop) or [REC] but-

ton to stop recording.

When using a Style or a Groove, you can stop

recording also by pressing the [INTRO/ENDING/

rit.] or [MUSICAL CLIMAX] button, and then wait-

ing until playback ends.

After recording finishes, “Writing!” appears indi-

cating that the recorded data is being stored, and

then the recorded track numbers in the display

will light.

To play back the recorded Song, press

the [ ] (Start/Stop) button.

This section explains how to record to a specified

track. This is useful when you want to record addi-

tional performances to an already recorded Song, or

re-record only one track of an already recorded

Song.

Press the [SONG] button, and then select

the desired User Song from 031–040

(User 1–10) as the recording target.

While holding down the [REC] button,

press the desired Track button to enter

the Record Ready mode.

 If you want to record only the melody:

While holding down the [REC] button, press

one of the [1/RIGHT]–[5] buttons.

 If you want to record only the Style play-

back:

Press the [STYLE] button, select the desired

Style, then simultaneously hold down the

[REC] button and press the [A] button. ACMP is

automatically turned on.

• Never attempt to turn the power off when “Writing!” is

shown in the display. Doing so can result in a loss of

data.

• When recording Groove playback with Retrigger, note

that the beat indicator in the display, metronome and

Arpeggio playback are not synchronized with playback of

the recorded Song.

• When recording a performance with a Sample Voice,

keep in mind that the Sample Voice itself is not recorded.

For the performance to sound as you intended, you will

need to assign that sample to the keyboard (the same as

used when recording).

• If you fast forward or rewind during playback of a Song

using Sample Voices, the playback sounds differ from the

original recording.

Limitations while recording

• The on/off status of ACMP cannot be changed.

•Playback cannot be changed between Style and

Groove.

• The Groove number can be changed while the Style

number cannot.

• When you use Style/Groove, the following parameters

cannot be changed: Reverb Type, Chorus Type, Time

Signature and Style/Groove Creator Volume.

• Performances with a Split Voice cannot be recorded.

•The audio input from an external device (playback

sound on the connected computer or audio device)

cannot be recorded.

• Performances using Sample Voices can be recorded

on track 1 only.

NOTICE

NOTE

Recording to a Specified Track

User 1

031

User 1

001

pEC

Selected track

flashes

Flashes

Press and

hold

Press and

hold

Recording Your Performance

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

 If you want to record only the Groove play-

back:

Press the [GROOVE CREATOR] button, and

then select the desired Groove. While holding

down the [REC] button, press the [A] button.

ACMP is automatically turned on.

Same as in steps 4 to 6 (page 38) in

“Quick Recording.”

Yo u can clear all tracks of a User Song.

Press the [SONG] button, then select the

User Song from 031–040 (User 1–10) to

be cleared.

Hold down the track [1/RIGHT] and [A]

buttons simultaneously for longer than a

second.

A confirmation message will appear on the dis-

play.

Press the [+/YES] button.

A confirmation message will appear on the dis-

play. To cancel this operation, press the [-] button.

Press the [+/YES] button to clear the

Song.

An in-progress message will appear briefly on the

display.

This lets you clear individual tracks from a User

Song.

Press the [SONG] button, and then

select the desired User Song from 031–

040 (User 1–10).

From [1/RIGHT]–[5] and [A], press the

Track button to be cleared for longer

than a second.

A confirmation message will appear on the dis-

play.

Press the [+/YES] button.

A confirmation message will appear on the dis-

play. To cancel this operation, press the [-] button.

Press the [+/YES] button to clear the

track.

An in-progress message will appear briefly on the

display.

• If the memory becomes full while recording, an alert mes-

sage will appear and recording will stop automatically. In

this case, delete unnecessary data by using the Clear

functions (below), and then execute the recording again.

Clearing a User Song

Press and

hold

NOTE

Hold simultaneously

for longer than a second.

ClrUser1

YES

Clearing a Specified Track from

a User Song

Hold for longer

than a second.

ClrTr1

YES

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Audio Playback and Recording

This instrument allows you to play back audio files and record your performances in

audio format. The recorded performance can be saved to a USB flash memory as an

audio file.

Yo u can playback audio files in a USB flash drive in

the Audio mode.

Connect a USB flash drive to the [USB

TO DEVICE] terminal.

For details, refer to “Connecting a USB Flash

Drive” on page 71.

Press the [AUDIO] button to enter the

Audio mode.

The audio file name, AUDIO icon and “PLY”

appear on the display.

Rotate the dial to select the desired

audio file.

Yo u can also use the CATEGORY [<<][>>] but-

tons, or the [+/YES][-/NO] buttons. To instantly

jump to the first audio file, press the [+/YES] and

[-/NO] buttons simultaneously.

Press the [ ] (Start/Stop) button to

start playback of the audio file.

During playback, the time elapsed is shown on

the display. To stop playback, press the [ ]

(Start/Stop) button again.

Press the [AUDIO] button to exit from the

Audio mode.

Message List

Audio file

An audio file is a recording of the performed sound itself. This data is recorded in the same way as that used in recording

with voice recorders, etc. This data can be played with a portable music player, etc., allowing you to easily let other people

hear your performance.

• This instrument can record or play 44.1kHz/16-bit stereo WAV files.

NOTE

Playing back an Audio File in a

USB Flash Drive

While in the Audio mode, some operations cannot be

executed. When you are not playing back or recording

audio files, exit from the Audio mode.

• Do not disconnect the USB flash drive or turn off the

power to the instrument during playback. Otherwise, dam-

age to the data may occur.

• To exit from the Audio mode, press the [AUDIO] button

again.

NOTICE

AUDIO001

PLY

Audio file name

For example, the file named

“A U D I O 0 0 1. wav” in the USB

flash drive is shown like this.

NOTE

The following operations cannot be executed for audio

playback.

• Changing the Voice

• A-B Repeat

• Turning off “tracks” (page 60)

• Changing the tempo

Message Description

No USB No USB flash drive is connected.

no file

There is no audio file in the USB flash

drive.

Err Load

Cannot load the audio file because the for-

mat is not compatible with this instrument.

USB Err

The USB flash drive may have a problem.

• Refer to “Compatible USB Device List for

PSR-E463/EW410” on the Yamaha web-

site.

• Format the USB Flash Drive.

NOTE

Audio Playback and Recording

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Yo u can record your performance and save it as an

audio file to the USB flash drive.

Connect a USB flash drive to the [USB

TO DEVICE] terminal.

For details, refer to “Connecting a USB Flash

Drive” on page 71.

Make the desired settings of your perfor-

mance.

Depending on the selected function, the data that

can be recorded differs as follows.

 When a Style is selected:

Style, keyboard performance, audio input from

the [AUX IN] jack

 When a Song is selected:

Keyboard performance, audio input from the

[AUX IN] jack

 When a Groove Creator is selected:

Groove, keyboard performance, audio input

from the [AUX IN] jack

Hold the [AUDIO] button for longer than

a second to enter the Audio mode

(recording standby).

“PressREC” and the AUDIO icon appear on the

display.

Press the [REC] button to start record-

ing.

The elapsed time is shown on the display during

recording.

The maximum recording time is 80 minutes or

until the memory of the USB flash drive becomes

full.

When stopping Style or Groove, press the [ ]

(Start/Stop) button.

Press the [REC] button to stop record-

ing.

“Writing!” appears indicating that the recorded

data is being stored. After storing, “Complet.”

appears, and then the recorded audio file name

will be shown as “AUDIO****” (****: number).

Press the [ ] (Start/Stop) button to

play back the recorded audio file.

Press the [AUDIO] button to exit from the

Audio mode.

Message List

Recording/Saving Audio Files to

a USB Flash Drive

• Connect an AC adaptor to use this function.

• Do not disconnect the USB flash drive or turn off the

power to the instrument during recording. Otherwise,

damage to the data may occur.

• Data that cannot be recorded includes: the metronome

click, Songs, and audio input from the [USB TO HOST]

terminal.

• To exit from the Audio mode, press the [AUDIO] button

again.

IMPORTANT

NOTICE

NOTE

pEC

PressREC

Hold for longer

than a second.

NOTE

• Never attempt to turn the power off when “Writing!” is

shown in the display. Doing so can result in a loss of

data.

Message Description

No USB No USB flash drive is connected.

UseAdpt

No power is being drawn from batteries.

Connect the AC adaptor.

File Ful

The total number of files in the USB flash

drive exceeds the capacity. Delete unnec-

essary data or use another USB flash

drive.

Unformat

The USB flash drive is unformatted. For-

mat it (page 72).

Protect

The USB flash drive is protected. Set

write-protect to off and try again.

Time Up

The recording time exceeds 80 minutes.

The recording automatically stops and the

audio file will be saved.

Disk Ful

Memory has become full. The recording is

stopped and the audio file will be saved.

USB Err

The USB flash drive may have a problem.

• Refer to “Compatible USB Device List for

PSR-E463/EW410” on the Yamaha web-

site.

• Format the USB Flash Drive.

NOTICE

Audio Playback and Recording

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Connect a USB flash drive to the [USB

TO DEVICE] terminal.

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

If the instrument is in the Audio mode, press the

[AUDIO] button to exit from the Audio mode, and

then execute this operation.

Use the CATEGORY [<<] and [>>] but-

tons to call up “DelAUDIO.”

Press the [0/EXECUTE] button.

Audio file names in the USB flash drive appear

on the display as “AUDIO****” (****: number).

Use the dial or the [+/YES][-/NO] button to select

a different audio file.

Press the [0/EXECUTE] button again.

A confirmation message will appear. To cancel

the operation, press the [-/NO] button.

Press the [0/EXECUTE] button again, or

the [+/YES] button to execute the Delete

operation.

After a while, a message indicating completion of

the operation appears.

Press the [FUNCTION] button to exit

from the File Control display.

Deleting Audio Files from the

USB Flash Drive

• The Delete operation cannot be cancelled during exe-

cution. Never turn off the power or disconnect the

USB flash drive during the operation. Doing so may

result in data loss.

Hold for longer

than a second.

DelAUDIO

AUDIO001

NOTICE

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Memorizing Your Favorite Settings (Registration Memory)

The Registration Memory function allows you to save

(or “register”) panel settings such as Voice and Style

to a Registration Memory button, and then instantly

recall your custom panel settings by simply pressing a

single button. The registered settings for four Regis-

tration Memory buttons will be saved as a single Bank.

Make the desired settings, such as those

for Voice, Style, and Groove.

Press the REGISTRATION MEMORY

[BANK/MEMORY] button to call up a Bank

number on the display.

Use the dial or the [1]–[8] number but-

tons to select a Bank number.

While holding down the [BANK/MEM-

ORY] button, press one of the [1]–[4] but-

tons to memorize the current panel

settings.

A “Mem OK” message appears indicating that the

panel settings will be stored temporarily. The data

is actually written to the memory when the power

is turn off.

Press and release the [BANK/MEMORY] but-

ton to call up a Bank number on the display.

Use the dial or the [1]–[8] number but-

tons to select a Bank number.

Press one of the REGISTRATION MEM-

ORY [1]–[4] buttons to call up the panel

settings you memorized.

The recalled Registration Memory number

appears in the display for a few seconds.

Up to 32 settings (eight banks of four

each) can be memorized.

Memory 1

8 Banks

Memory 2 Memory 3 Memory 4

Memorizing Panel Settings to

the Registration Memory

• Data cannot be saved to Registration Memory during

Song playback.

• If you select a Registration Memory number that

already contains data, the previous data is deleted and

overwritten by the new data.

• Samples are not memorized. Save them to a USB Flash

Drive (page 34).

NOTE

Bank

Bank number

Press and

hold

NOTICE

Recalling Panel Settings from

the Registration Memory

• When the [SONG] lamp is lit, the Style or Groove settings

will not be recalled even if you press the [REGISTRATION

MEMORY] button to which the Style or Groove settings are

memorized. To recall Style/Groove settings, make sure to

press the [STYLE] or [GROOVE CREATOR] button before-

hand.

Parameters that can be memorized to Registra-

tion Memory

Style settings: Style number, ACMP on/off, Style vol-

ume, Track on/off, Main section A/B, Tempo

Groove settings: Groove number, Groove volume,

Section, Track on/off, Tempo

Voice settings:

Main Voice settings: Voice number and all settings of

the related Functions (page 67)

Dual Voice settings: Dual on/off and all settings of

the related Functions

Split Voice settings: Split on/off and all settings of

the related Functions

Effect settings: Reverb Type, Chorus Type

Harmony / Arpeggio settings: Harmony/Arpeggio

on/off and all settings of the related Functions

DSP: DSP on/off, DSP type and parameter values of

Knobs A/B.

Other settings: Transpose, Pitch Bend Range, Knob

Assign, Target, Split Point, Scale Tune

REGIST 1

Registration

Memory number

NOTE

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Connecting to Other Devices

Connecting Headphones

Connect a pair of headphones to the [PHONES/

OUTPUT]/[PHONES] jack on the rear panel.

The built-in speakers are automatically shut off when

a plug is inserted into this jack.

Connecting an External Device

• PSR-E463: This jack also functions as an external

output. By connecting to a computer, keyboard

amplifier, recorder, or other audio device, you can

output the audio signal of this instrument to that

external device. The speakers of this instrument

are automatically shut off when a plug is inserted

into this jack.

• PSR-EW410: When connecting an external

speaker, refer to page 48.

Yo u can produce a natural sustain as you play by

pressing a footswitch (FC5 or FC4A; sold separately)

plugged into the [SUSTAIN] jack.

• Before connecting the instrument to external devices, turn off the power of all the devices. Also, before turning the power on or

off, make sure to set all volume levels to minimum. Otherwise, damage to the devices or electrical shock may occur.

CAUTION

Connecting Headphones or an

External Device

• Do not use the headphones for a long period of time at a

high or uncomfortable volume level, since this can cause

permanent hearing loss.

• To avoid possible damage to the external device, first turn

on the power to the instrument, then to the external

device. When turning off the power, do so in reverse order:

first turn off the power to the external device, then to the

instrument.

Standard stereo

phone plug

CAUTION

NOTICE

Using a Pedal (Sustain)

• Plug or unplug the footswitch while the power is off. Also, do

not press the footswitch when turning the power on. Doing so

changes the polarity of the footswitch, resulting in reversed

operation.

• The sustain function does not affect Split Voices (page 21).

• Some Voices may sound continuously or have a long decay

after the notes have been released while the footswitch is

held.

NOTE

Connecting to Other Devices

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

By connecting an audio device such as a portable

music player to the instrument’s [AUX IN] jack, you

can output the sound of the audio device through the

built-in speakers of this instrument. This lets you play

the keyboard along with the playback of your audio

player, for practice or performance.

Connect the headphone jack of an audio

device to the instrument’s [AUX IN] jack

by using an audio cable.

Turn on the audio device, and then this

instrument.

Start play back of the connected audio

device.

The sound of the audio device is output through

the speakers of this instrument.

Adjust the volume balance between the

audio device and this instrument.

Adjust the audio playback volume on the audio

device, then adjust the entire volume by rotating

the [MASTER VOLUME] control of the instru-

ment.

Play the keyboard along with the sound

of audio device.

After finishing your performance, stop

playback of the audio device.

When you output the audio sound of an external

audio device or a computer connected to the [AUX

IN] jack or the [USB TO DEVICE] or [USB TO HOST]

terminal through this instrument, you can cancel or

lower the volume of the melody part of audio play-

back. You can use the function to practice the mel-

ody part along with the audio playback.

Play back audio on the connected exter-

nal device.

Press the [MELODY SUPPRESSOR] but-

ton to turn it on.

Press the [MELODY SUPPRESSOR] but-

ton again to turn it off.

Playing an External Audio

Device with the Built-in

Speakers

• To avoid damage to the devices, first turn on the power to

the external device, and then to the instrument. When turn-

ing off the power, first turn off the power to the instrument,

and then to the external device.

• If you are using a computer or a smart device such as an

iPhone/iPad, you can also connect it to the [USB TO

HOST] terminal (see “Using with Computer or Smart

Device,” at right).

NOTICE

Stereo mini plug

Audio device (portable

music player, etc.)

Headphone

jack

Audio cable

Stereo mini plug

NOTE

• If you want to adjust the volume balance between the

audio input from the external device and Style/Song/

Groove Creator, use the [TARGET] button to select Func-

tion number 5, then turn Knob A (page 58).

The audio input volume from the [AUX IN] jack can also

be adjusted in the Function Settings (page 66, Function

004). If you increase the volume to more than 50, the

audio device sound may be distorted.

• You can cancel or lower the volume of the melody part of

audio playback. For details, refer to page 46.

Using the Melody Suppressor

• Depending on the particular music source, the melody or

vocal sound may not be cancelled as expected even

when if the Melody Suppressor is turned on. In such a

case, try adjusting the pan position to be cancelled in the

Function Settings (page 68, Function 039).

• When the instrument is connected to the [USB TO HOST]

terminal, and Audio Loop Back (page 69, Function 056)

is set to OFF, the Melody Suppressor function cannot be

used.

NOTE

Appears when the

Melody Suppressor is

on.

NOTE

Connecting to Other Devices

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Connecting the [USB TO HOST] terminal of this

instrument and the computer or smart device allow

you to use various function with just one USB cable,

such as sending/receiving data with high sound qual-

ity, using the app of smart device, etc. The range of

the instrument can do is extended. For details on

using a computer or smart device, refer to the online

PDF manual (page 11) “Computer-related Opera-

tions” or “iPhone/iPad Connection Manual.”

Transmit/Receiving MIDI data

When transmitting/receiving MIDI data, you can do

the following as examples.

 Playbacking MIDI data

Yo u can purchase data on the Yamaha website.

 Recording the performance of the instrument

as MIDI data

Yo u can edit the data, such as sound, pitch, etc. on

music production software.

 Using the external sound like a software syn-

thesizer with keyboard on this instrument.

Yo u can performance with sounds other than built-

in.

 Using as a master keyboard to enter data on

music production software or notation soft-

ware.

Yo u can program on a music production software

or enter notes on notation software.

Sending/Receiving Audio data (USB

Audio Interface)

When sending/receiving audio data by digital signal,

you can do the following as examples.

 Playbacking audio data with high sound qual-

ity

Yo u can enjoy clear sound that is less degradation

of sound quality than connecting with [AUX IN] ter-

minal.

 Recording the performance of this instrument

as audio data on recording software or music

production software

Yo u can playback the recorded data with computer

or smart device.

Using Smart Device Apps

Using the smart device apps that are compatible with

the instrument, you can do the following as exam-

ples.

 Piano Diary

Yo u can leave the performance like diary.

 Cloud Audio Recorder

Yo u cannot only record the performance, but also

upload data with one button on the music sharing

service “Sound Cloud.”

For details of the corresponding smart device or

apps, refer to the Yamaha website.

Using with Computer or Smart

Device

• Use an AB type USB cable of less than 3 meters. USB 3.0

cables cannot be used.

• If you are using a DAW (digital audio workstation) with this

instrument, set the Audio Loop Back (page 69) to OFF. Oth-

erwise, a loud sound may occur, depending on the set-

tings of the computer or the application software.

• When using the Windows computer, install the Yamaha Stein-

berg USB Driver on the computer. For details, refer to the

online PDF manual (page 11) “Computer-related Operations.”

USB cable

USB

terminal

Instrument

Computer

[USB TO HOST]

terminal

NOTICE

NOTE

• For details of MIDI, refer to the online PDF manual (page 11)

“MIDI Reference.”

• The volume can be adjusted on the computer or smart device,

and also by using the instrument’s [MASTER VOLUME] con-

trol.

• The audio data from computer or smart device cannot be

played on the instrument in Quick Sampling mode or Audio

mode.

NOTE

Connecting to Other Devices

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Yo u can connect a stereo system to amplify the

instrument’s sound by using the OUTPUT [L/L+R]/

[R] jacks.

Yo u can use the instrument’s [MASTER VOLUME]

dial to adjust the volume of the sound output to the

external device.

Yo u can set whether the sound of this instrument is

always output from its built-in speaker or not.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “SP Mute” (Function 063).

Use the dial to select the desired setting.

When Speaker Mute is set to “ON,” the Speaker

sound is off. You can only hear the instrument

sound via the headphones or an external device

connected to the [OUTPUT] jacks.

When Speaker Mute is set to “OFF,” the speaker

sound is always on as long as headphones are

not connected.

Using an External Stereo

System for Playback (OUTPUT

[L/L+R]/[R] jacks) (PSR-EW410)

• Use audio cables and adaptor plugs having no (zero) resis-

tance.

• Use only the [L/L+R] jack for connection with a monaural

device.

• To avoid possible damage, first turn on the power to the

instrument, then to the external device. When turning off

the power, first turn off the power to the external device,

then to the instrument. Since this instrument’s power may

automatically be turned off due to the Auto Power Off func-

tion (page 16), turn off the power to the external device, or

disable Auto Power Off when you do not intend to operate

the instrument.

• Do not route the output from the OUTPUT jacks to the

[AUX IN] jack. If you make this connection, the signal input

at the [AUX IN] jack is output from the [OUTPUT] jacks and

then back again, creating a feedback loop that could make

normal performance impossible, and may even damage

the equipment.

Phone plug

(standard)

Audio cable

Phone plug

(standard)

Input jack

Powered speaker

Audio signal

NOTE

NOTICE

Speaker Mute On/Off Setting

(PSR-EW410)

SP Mute

OFF

063

PSR-E463/PSR-EW410 Owner’s Manual

Quick Guide

Backup and Initialization

The following Backup parameters will be maintained

even if the power is turned off.

In addition to the Backup parameters above, all the

data (including Style data that have not been loaded)

transferred from the connected computer will be

maintained, even if you turn off the power.

Yo u can erase the backup parameter settings

described above, and then restore all the default fac-

tory settings. The instrument can be initialized with

the following two methods.

Backup Clear

This operation initializes the backup parameters.

While holding down the highest white key, press the

[ ] (Standby/On) switch to turn the power on.

Flash Clear

This operation deletes all the Songs and Styles that

have been transferred from a computer. Note that

Style data loaded to Style numbers 221–230 will be

maintained. While simultaneously holding the high-

est white key and the three highest black keys, press

the [ ] (Standby/On) switch to turn the power on.

Backup Parameters

Backup parameters (each time)

• Use Songs (page 38)

• Style data transferred from a computer and loaded to

Style numbers 221–230 (page 75)

• Assigned Sample to keyboards (page 35)

Backup parameters when turning off the power

• Registration Memory (page 44)

• FUNCTION Settings: (page 66)

Style Volume, Song Volume, Groove Volume, Audio

Input Volume, Tuning, Split Point, Touch Response,

Master EQ Type, Audio Loop Back on/off, Blank Cut

on/off, Metronome Volume, Demo Group, Demo

Play Mode, Auto Power Off Time, Battery Type, Lan-

guage

Backup is executed automatically when the power is turned

off. When the power is turned off in the following cases,

backup is not executed.

• Disconnected AC adaptor

• Power failure

• Low or no battery power

NOTICE

Initializing the Instrument

• Keep in mind that this operation also deletes any data you

have purchased and loaded. Be sure to save important

data to a computer. For details, refer to the online PDF

manual (page 11) “Computer-related Operations.”

PSR-EW410

PSR-E463

The highest white key

PSR-EW410

PSR-E463

The highest white key

and the three highest

black keys

NOTICE

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Handy Performance Features

Selecting a Reverb Ty p e

The Reverb effect lets you play with a rich concert

hall type ambience.

Although selecting a Style or Song will call up the

optimum Reverb type for the entire sound, you can

select a different Reverb type manually.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “Reverb” (Function 036).

After a few seconds, the current Reverb type

appears.

Rotate the dial to select a Reverb type.

Play the keyboard to check the sound. For infor-

mation about the available Reverb types, refer to

the Effect Type List in the separate Data List.

Selecting a Chorus Type

The Chorus effect creates a thick sound that sounds

like many of the same Voices being played in unison.

Although selecting a Style or Song will call up the

optimum Chorus type for the entire sound, you can

select a different Chorus type manually.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “Chorus” (Function 037).

After a few seconds, the current Choru s type

appears.

Rotate the dial to select a Chorus type.

Play the keyboard to check the sound. For infor-

mation about the available Chorus types, refer to

the Effect Type List in the separate Data List.

• Some Songs and Styles use Reverb Types which cannot

be selected via panel operation. If such a Song or Style

is played back, “- - -” is shown on the display.

Adjusting the Reverb depth

Yo u can adjust the Reverb depth applied to the

Main, Dual, and Split Voices individually via the

same operations above. Regarding the item in step

2, refer to the Function List on page 68.

Reverb

036

Hall2

036

Current Reverb type

NOTE

• Some Songs and Styles use Chorus Types which cannot

be selected via panel operation. If such a Song or Style

is played back, “- - -” is shown on the display.

Adjusting the Chorus depth

Yo u can adjust the Chorus depth applied to the

Main, Dual, and Split Voices individually via the

same operations above. Regarding the item in step

2, refer to the Function List on page 68.

Chorus

037

Chorus1

037

Current Chorus type

NOTE

Reference

Handy Performance Features

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Pitch Controls—Transpose

The overall pitch of the instrument (except for the

Drum Kit Voices and Sample Voice) can be shifted

up or down by a maximum of 1 octave in semitone

increments.

Press the [TRANSPOSE] button to call

up “Transpos” (Function 006).

Use the dial to set the Transpose value

between -12 and +12.

Pitch Controls—Fine Tuning

The overall tuning of the instrument (except for the

Drum Kit Voices) can be shifted up or down between

427.0 Hz and 453.0 Hz in approximately 0.2 Hz incre-

ments. The default value is 440.0 Hz.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “Tuning” (Function 007).

Use the dial to set the Tuning value.

Pitch Controls—the [PITCH

BEND] wheel

The [PITCH BEND] wheel can be used to add

smooth pitch variations to notes you play on the key-

board. Roll the wheel upward to raise the pitch, or

downward to lower the pitch.

Yo u can change the amount of pitch bend produced

by the wheel in the Function Settings (page 66, Func-

tion 008).

Calling Up Optimum Panel

Settings—One Touch Setting

(OTS)

Select a Song, Style or Groove by pressing the

[SONG], [STYLE] or [GROOVE CREATOR] button,

and then select Voice number 000 OTS (page 20).

This lets you automatically call up the optimum panel

settings such as Voice and tempo for the current

Song, Style or Groove.

Transpos

006

Tuning

007

440.0Hz

007

Handy Performance Features

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Changing the Touch Response of

the Keyboard

The keyboard of this instrument is equipped with a

Touch Response feature that lets you dynamically

and expressively control the level of the Voices

according to your playing strength.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “TouchRes” (Function

010).

After a few seconds, the current Touch Response

appears.

Use the dial to select a Touch Response

setting between 1 and 4.

Touch Response

Selecting an EQ Setting for the

Best Sound

Six different master equalizer (EQ) settings give you

the best possible sound when listening through dif-

ferent reproduction systems—the instrument’s inter-

nal speakers, headphones, or an external speaker

system.

Hold down the [MELODY SUPPRESSOR]

button for longer than a second to call

up “Master EQ” (Function 038).

After a few seconds, the current Master EQ type

appears.

Rotate the dial to select the desired Mas-

ter EQ type.

Master EQ types

1Soft

Allows maximum loudness to be pro-

duced with relatively light key pres-

sure.

2Medium

Produ ces a fairly “standard” key-

board response.

3Hard

Requires strong playing to produce

high volume.

4Fixed

All notes are produced at the same

volume no matter how hard the key-

board is played.

TouchRes

010

Medium

010

Current Touch

Response

1 Speaker

Optimum for listening via the instru-

ment’s built-in speakers.

2 Headphone

Optimum for headphones, or for lis-

tening via external speakers.

3Boost

Results in more powerful sound.

Depending on the selected Voice and

Style, etc., the sound may be more

subject to distortion than other EQ

types.

4Piano Optimum for piano solo performance.

5Bright

Lowers the mid range for a brighter

sound.

6 Mild

Lowers the high range for a softer

sound.

MasterEQ

038

Speaker

038

Current Master

EQ type

Hold for longer

than a second.

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Scale Tuning

By default, the scale of this keyboard is set to Equal Temperament — the same tuning

as with any acoustic piano. However, the setting can be changed to any other scale

according to the music genre or style in which you want to play.

Selecting a Scale

Yo u can select a desired scale among the various

preset scales.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] button

to call up “Scale” (Function 046).

After a few seconds, the current scale appears.

Rotate the dial to select a scale.

The default setting is “1 Equal.”

Preset Scale types

Setting the Base Note for Each

Scale

Make sure to specify the appropriate base note, if

you select a scale other than Equal Temperament, or

create an original scale via Scale Tune function.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] button

to call up “BaseNote” (Function 047).

After a few seconds, the current base note

appears.

Rotate the dial to select a base note from

C, C#, D, Eb, E, F, F#, G, Ab, A, Bb and B.

The default setting is “C.”

1Equal

2Pure Major

3Pure Minor

4Bayat (Arabic)

5Rast (Arabic)

Scale

046

Equal

046

Current scale

BaseNote

047

Current base note

Scale Tuning

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Tuning Each Note to Create an

Original Scale

Yo u can tune the individual notes in cents (a “cent” is

1/100th of a semitone) to create your own original

scale.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “TuneNote” (Function

048).

After a few seconds, the current note appears.

Rotate the dial to select the note to be

tuned from C, C#, D, Eb, E, F, F#, G, Ab, A,

Bb, B.

Press the CATEGORY [>>] button to call

up “Tune” (Function 049).

After a few seconds, the tuning value of the note

selected in step 3 appears.

Rotate the dial to tune the note over a

range of -64 to +63.

The setting can be reset to the initial default value

by pressing the [+/YES] and [-/NO] buttons simul-

taneously.

Repeat steps 2–5 as desired.

Memorize the settings here to a Regis-

tration Memory as desired (page 44).

TuneNote

048

Current tuning note

Tune C

049

Tune

049

Tuning value

• When pressing the [+/YES] and [-/NO] buttons simultane-

ously after recalling an original scale memorized to Reg-

istration Memory, the scale will return to the original scale

registered to Registration Memory, not to the default tune

value.

• When calling up “Scale” (Function 046) after using indi-

vidual note scale tuning, “(Edited)” will be shown in the

display. However, the edited scale settings will be erased

by calling up another scale. For this reason, the edited

settings should be memorized to Registration Memory.

NOTE

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Voice Settings

Selecting a Dual Voice

Hold down the [DUAL] button for longer

than a second to call up “D.Voice”

(Function 020).

After a few seconds, the current Dual Voice

appears.

Rotate the dial to select the desired Dual

Voic e.

Selecting a Split Voice

Hold down the [SPLIT] button for longer

than a second to call up “S.Voice” (Func-

tion 030).

After a few seconds, the current Split Voice

appears.

Rotate the dial to select the desired Split

Voic e.

Voice Editing

Each of the Main, Dual and Split Voices can be

edited, with available parameters including volume,

octave and Reverb/Chorus depth—allowing you to

create new, custom sounds to best suit your own

musical preferences.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up the desired item.

Voice parameters are indicated as below.

• Main Voice parameters: M.****** (Function

011–019)

•Dual Voice parameters: D.****** (Function

020–029)

• Split Voice parameters: S.****** (Function

030–035)

For details on each parameter, refer to the Func-

tion List on page 67.

Rotate the dial to set the value.

Check the sound by playing the keyboard.

Repeat steps 2–3 above to edit various

parameters.

If necessary, memorize the settings to a

Registration Memory (page 44).

The Voice-related settings are reset when a dif-

ferent Voice is selected. If you want to store the

created sound for future recall, memorize the set-

tings to a Registration Memory.

D.Voice

020

Chamber

071

020

Current Dual Voice

Hold for longer

than a second.

S.Voice

030

FngrBass

054

030

Current Split Voice

Hold for longer

than a second.

M.Volume

064

011

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Arpeggio Settings

Synchronizing an Arpeggio to

Song/Style/Groove Playback—

Arpeggio Quantize

When you play the keyboard to trigger an Arpeggio

(page 22) along with Song/Style/Groove playback,

you’ll need to play the notes with correct timing to

keep the Arpeggio in synchronization with the other

playback tracks. However, your actual timing may be

slightly ahead of or behind the beat (or both). The

“Arpeggio Quantize” function of this instrument will

correct any slight imperfections in the timing (accord-

ing to settings below), and then play back the Arpeg-

gio appropriately.

• No synchronization

• Synchronizing to 8th notes

• Synchronizing to quarter notes

Although the Arpeggio Quantize value is pre-pro-

grammed for each Arpeggio Type, you can change

the value manually.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up the “Quantize” (Function

044).

After a few seconds, the current Arpeggio Quan-

tize value appears.

Rotate the dial to select a value from

“OFF,” “1/8” and “1/16.”

• OFF No synchronization

• 1/16 Synchronizing to 8th notes

• 1/8 Synchronizing to quarter notes

Holding the Arpeggio Playback

via the Footswitch

Yo u can set the instrument so that Arpeggio play-

back continues even after the note has been

released, by pressing the footswitch connected to the

[SUSTAIN] jack.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “Pdl Func” (Function

045).

After a few seconds, the current pedal setting

appears.

Rotate the dial to select “Arp Hold.”

If you want to restore the footswitch function to

sustain, select “Sustain.” If you want to use both

hold and sustain functions, select “Hold+Sus.”

Try playing the Arpeggio with the foot-

switch.

Press the notes to trigger the Arpeggio, then

press the footswitch. Even if you release the

notes, Arpeggio playback will continue. To stop

Arpeggio playback, release the footswitch.

Quantize

044

1/8

044

Current value

Pdl Func

045

Sustain

045

Current setting

Arp Hold

045

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Parameters Assigned to the Knobs

This section describes each of the parameters which can be assigned to the Knobs (page 25).

z CUTOFF/RESONANCE

These effects shape the sound by allowing only a

specified range of frequencies to pass and/or by pro-

ducing a resonance peak at the “cutoff” frequency.

These effects can be used to create a range of syn-

thesizer-like sounds.

 Knob A: CUTOFF

Adjusts the cutoff frequency, and therefore the

brightness of the sound. Turning the knob to the

left makes the sound more muffled or darker, while

turning the knob A to the right makes the sound

brighter.

 Knob B: RESONANCE

Adjusts the amount of Resonance applied at the

cutoff frequency. Turning the knob to the right

increases the Resonance to emphasize the fre-

quencies at the cutoff frequency, resulting in an

exaggerated peak.

x REVERB/CHORUS

 Knob A: REVERB

Reproduces the acoustic ambience of a concert

hall or club. Turning the knob to the right increases

the Reverb depth.

 Knob B: CHORUS

Produces a rich and warm layered effect. Tu rning

the knob to the right increases the Chorus depth.

c DSP

 Knob A/B: DSP PARAMETER A/B

With the digital effects built into the instrument, you

can add DSP effects to your keyboard performance

and the playback sound of Style, etc. (page 24).

Each effect has two parameters which are

assigned to Knobs A and B. By turning the knobs

in real-time, you can alter the music in various

dynamic ways, such as changing the rotating

speed (slow/fast) of the rotary speaker or changing

the degree of the Distortion.

v ATTACK/RELEASE

These effects determine how the level of the sound

varies over time. You can make the attack faster for a

more percussive sound or slower for a violin-like

sound, for example. Or you can lengthen or shorten

the sustain to best match the music you’re playing.

 Knob A: ATTACK

Adjusts the Attack Time (the amount of time it

takes the sound to reach maximum level when a

key is played). Turning the knob to the right

increases the Attack Time, thus slowing down the

attack rate.

 Knob B: RELEASE

Adjusts the Release Time (the amount of time it

takes for the sound to decay to silence after a key

is released). Turning the knob to the right

increases the Release Time, thus making a longer

sustain.

• When the target is KEYBOARD, these effects are applied to

the Main/Dual Voices. When the target is BACKING, these

effects are applied to the Styles and Grooves.

• These effects can sometimes cause distortion, especially in

the bass frequencies.

NOTE

Level

Frequency

Cutoff Frequency

Frequencies in this

range are passed.

Frequencies in this

range are cut off.

Level

Frequency

Resonance

• When the target is KEYBOARD, these effects are applied to

the Main/Dual Voices. When the target is BACKING, these

effects are applied to the Styles and Grooves.

• These effects are applied only KEYBOARD. The target can-

not be switched to BACKING.

NOTE

Sustain Level

Level

Time

Key Played Key Released

ATTACK DECAY RELEASE

NOTE

Parameters Assigned to the Knobs

PSR-E463/PSR-EW410 Owner’s Manual

Reference

b VOLUME BALANCE/RETRIGGER RATE

 Knob A: VOLUME BALANCE

Adjusts the volume balance between the audio

playback volume from the connected audio device

(page 46) or the computer (page 47) and the

Song/Style/Groove. Turning the knob to the left

decreases the external audio volume, while turning

it to the right decreases the instrument volume.

Even when there is no audio input from an external

device, the volume of Song, Style and Groove can

be adjusted by using the knob. The volume of

Voices played on the keyboard cannot be adjusted.

 Knob B: RETRIGGER RATE

Adjusts the Retrigger Rate (the length of the part

to be r

epeated) of the Groove Retri

gger function

(page 61). Turning this knob to the right decreases

it, and turning the knob to the left increases it.

The chart below lists some interesting ways to use the various effects that can be assigned to the knobs.

Some Ideas for Using the Knobs

• When the instrument is connected to the [USB TO HOST]

terminal, and Audio Loop Back (page 69, Function 056) is

set to OFF, you cannot adjust the volume of audio playback

input from the external device.

NOTE

• When setting the tempo of the Groove playback to more

than 200, turning the knob to the right cannot change the

length to be repeated.

NOTE

Number/Effect Try This

CUTOFF/RESONANCE

Select “143 Gemini” (a synth-lead type Voice) or “170 Noise”. Select

z with [KNOB

ASSIGN] button, and then switch the target to KEYBOARD. Turning Knobs A or B while

playing gives you the dynamic filter-sweep effects of an analog synthesizer.

REVERB/CHORUS

Select the Voice “008 CP80.” Select

x with [KNOB ASSIGN] button, and then switch the

target to KEYBOARD. Turn Knobs A and B all the way down to hear the direct, unpro-

cessed sound of the Voice. As you turn Knob B toward the right, a Chorus effect with

modulation is gradually applied to the sound. Turning Knob A to the right adds a Reverb

effect that makes you sound like you are playing in a concert hall.

DSP

Select the Voice, “019 Cool!Org.” Select

c with [KNOB ASSIGN] button, and then switch

the target to KEYBOARD. Press the [DSP] button to turn the DSP on, then set the DSP

type (Function 040) to “01 RotarySp.” Use Knob A to change the rotating speed of the

rotary speaker while playing the keyboard. When you move it slowly, you can create

gradual speed changes like on a real rotary speaker. Use Knob B to control the distor-

tion.

ATTACK/RELEASE

Select the Voice “173 RSAnPad.” Turning Knob A all the way down makes the attack

faster, and lets you hear the crisp, clear sound of the original Voice. Turning Knob B all

the way down shortens the amount of time for the sound to decay to silence after a key is

released. These knobs let you finely adjust the Voice to create the appropriate sound for

the particular song you’re playing.

VOLUME BALANCE/

RETRIGGER RATE

Knob A: Connect an audio device or a computer (page 46), then turn this knob while

playing audio on the external device. You can adjust the volume balance between the

performance on this instrument and the audio input.

Knob B: Select the Section C of the Groove “008 FrenchDJ” and start Groove playback.

Turn this knob to the right while holding down the Section button C, and you can pro-

gressively shorten the Retrigger rate like a DJ would in performance.

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Style and Groove Settings

Style Variations—Sections

Each Style consists of “Sections” that allow you to vary the arrangement of the accompaniment to match the

song you are playing.

INTRO

This is used for the beginning of the Song. When the Intro finishes, Style playback shifts to the Main sec-

tion. The length of the Intro (in measures) differs depending on the selected Style.

MAIN

This is used for playing the main part of the Song. Playback of the Main section repeats indefinitely until

another Section’s button is pressed. There are two variations (A and B), and the Style playback sound

changes harmonically in response on the chords you play with your left hand.

AUTO FILL

This is automatically added before changing to Main A or B.

ENDING

This is used for the ending of the Song. When the Ending finishes, the Style playback stops automatically.

The length of the Ending (in measures) differs depending on the selected Style.

Press the [STYLE] button, then rotate the

dial to select a Style.

Press the [ACMP ON/OFF] button to turn

ACMP on.

Press the [SYNC START] button to turn

Synchro Start on.

To t urn off Synchro Start, press the [SYNC

START] button.

Synchro Start

When Synchro Start is on, Style playback will

begin as soon as you play a chord in the Auto

Accompaniment area of the keyboard.

Press the [MAIN/AUTO FILL] button to

select Main A or Main B.

INTRO MAIN A/B

ENDING AUTO FILL

Appears when ACMP

is turned on.

Beat arrows

flash.

MAIN A

Current Section

(Main A or B)

Style and Groove Settings

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Press the [INTRO/ENDING/rit.] button.

Now, you’re ready to start Style playback of the

Intro and then the Main A (or B) section.

Play a chord with your left hand to start

playback of the Intro.

For information on how to play chords, see

“Chords” on page 63.

After the Intro finishes, play the key-

board according to the progression of

the Song you are playing.

Play chords with your left hand while playing mel-

odies with your right hand, and press the [MAIN/

AUTO FILL] button as necessary. The Section will

change to Fill-in then Main A or B.

Press the [INTRO/ENDING/rit.] button.

The Section switches to the Ending. When the

Ending is finished, Style playback stops automat-

ically. You can have the Ending gradually slow

down (ritardando) by pressing the [INTRO/END-

ING/rit.] button again while the Ending is playing

back.

Style Synchro Stop

When you press the [SYNC STOP] button to turn on

this function, the Style will only play while pressing

chords in the Auto Accompaniment area of the key-

board. Releasing all the notes will stop Style play-

back.

Turning Each Style Track On/Off

As printed on the front panel, a Style consists of six

tracks. Turn on/off each track via the TRACK CON-

TROL buttons. Each of the tracks can be muted so

that you can play the muted part yourself. Pressing

the desired Track button repeatedly will toggle the on/

off status.

• Style numbers 211, 223–235 have no rhythm parts, so no

rhythm will play. When one of these Styles is selected, turn

ACMP on, then specify the chord in the Auto Accompaniment

area to play Style parts other than the Rhythm part.

INTRO≥A

Split Point

Auto Accompa-

niment area

FILL A≥B

ENDING

NOTE

• This function can be used when ACMP is turned on.

• Up to two Track buttons can be pressed simultaneously for

turning Tracks on or off.

Appears when the syn-

chro-stop function is

engaged.

NOTE

On/off status is shown in

the display (page 19)

NOTE

Style and Groove Settings

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Groove Variations—Sections

Like the Styles, each Groove features several Sec-

tions, allowing you to add dynamic variations to the

performance. Five Sections (A–D, MUSICAL CLI-

MAX) are available.

Unlike the Styles, however, Groove do not have Sec-

tions dedicated to the beginning or ending of the

Song, such as Intro and Ending. All Sections A–D

will play back repeatedly until stopped manually.

Groove Retrigger Fu nction

This function restarts Groove playback from the

beginning.

Press the [GROOVE CREATOR] button,

then rotate the dial to select the desired

Groove.

Press the [START/STOP] button or press

any key in the Auto Accompaniment area

to start Groove playback (page 30).

By pressing the button of the currently

playing Section, you can restart play-

back from the beginning. Holding down

the button lets loop-play only the top

portion of the Section.

The top portion length (Retrigger Rate) can be

changed by using the knob (page 58).

Changing the Tempo

A Style or Groove can be played at any tempo you

desire—fast or slow—and the tempo can be

changed precisely.

Press the [TEMPO/TAP] button to call up

the Tempo value in the display.

Rotate the dial to set a tempo from 011 to

280.

Pressing the [+/YES] and [-/NO] buttons simulta-

neously can instantly reset the value to the

default tempo of the current Style or Groove. You

can change the tempo during playback by press-

ing the [TEMPO/TAP] button just twice at the

required tempo.

Tap Start

Yo u can start play back of the Style, Groove or Song

by simply tapping the [TEMPO/TAP] button at the

required tempo—four times for time signatures in 4

(4/4, etc.), and three times for time signatures in 3 (3/

4, etc.).

• When recording Groove playback with the Retrigger function,

note that the beat indicator in the display, metronome and

Arpeggio playback is not synchronized with playback of the

recorded Song.

NOTE

• The above operation applies also to Song or Arpeggio

playback tempo.

• Tap tempo setting range: 32–280

Tempo

090

Current Tempo

NOTE

Style and Groove Settings

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Adjusting the Volume of the Style

or Groove

Yo u can adjust the volume balance between Style or

Groove playback and your keyboard performance.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “StyleVol” (Function 001)

or “GroovVol” (Function 003).

Rotate the dial to set the volume

between 000 and 127.

Setting the Split Point

The point on the keyboard that separates the left-

hand area and the right-hand area of the keyboard is

called the “Split Point.” The left-hand area is used to

specify the chord for Style playback, to specify the

key for Groove playback, or to play the Split Voice.

The default Split Point is key number 054 (the F#2

key), but you can change it to another key.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “SplitPnt” (Function 009).

Yo u can call up this display also by pressing the

[STYLE] then holding the [ACMP] button for lon-

ger than a second.

Rotate the dial to set the Split Point

between 036 (C1) and 096 (C6) (on the

PSR-E463) or 028 (E0) and 103 (G6) (on

the PSR-EW410).

Playing Chords Without Style

Playback (Stop Accompaniment)

If you press the [STYLE] button, press the [ACMP

ON/OFF] button to turn ACMP on (the ACMP ON

icon appears), and play the chord in the Auto Accom-

paniment area of the keyboard (with SYNC START

off), the chord sound will be heard without Style play-

back. This is referred to as “Stop Accompaniment.”

The specified chord will be shown in the display, and

affects the Harmony function (page 22).

StyleVol

100

001

Style (or Groove) volume

SplitPnt

054

009

Split Point

Split Voice,

chords (Style) or

keys (Groove)

Main Voice (and Dual Voice)

036

(C1)

048

(C2)

060

(C3)

072

(C4)

084

(C5)

096

(C6)

Split Point ... default value: 054 (F#2)

Auto Accompani-

ment area

Specified

chord

Appears when auto accom-

paniment is on

Style and Groove Settings

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Chord Types for Style Playback

For users who are new to chords, this chart features common chords. Since there are many useful chords and

many different ways to use them musically, refer to commercially available chord books for further details.

 indicates the root note.

• Inversions can be used as well as in “root” position—with the following exceptions:

m7, m7

5, m7(11), 6, m6, sus4, aug, dim7, 7

5, 6(9), sus2

• Inversion of the 7sus4 chords are not recognized if the notes are omitted.

• When playing a chord which cannot be recognized by this instrument, nothing is shown on the display. In such a case, only the rhythm

and bass parts will be played.

Major Minor Seventh Minor Seventh Major Seventh

Easy Chords

This method lets you easily play chords in the Auto Accompaniment area of the keyboard using only one, two, or three fin-

gers.

For root “C”

To play a major chord

Press the root note () of

the chord.

To play a minor chord

Press the root note together

with the nearest black key to

the left of it.

To play a seventh chord

Press the root note together

with the nearest white key to

the left of it.

To play a minor seventh chord

Press the root note together with the

nearest white and black keys to the

left of it (three keys altogether).

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Song Settings

Background Music Playback

With the default setting, pressing the [DEMO] button

will play back only a few of the internal Songs repeat-

edly. This setting can be changed so that, for exam-

ple, all internal Songs are played, or all Songs

transferred to the instrument from a computer are

played back, letting you use the instrument as a

background music source. Six playback group set-

tings are provided for your listening pleasure.

Hold down the [DEMO] button for longer

than a second to call up “DemoGrp.”

After a few seconds, the current repeat playback

group appears.

Rotate the dial to select a repeat play-

back group from the table below.

Press the [DEMO] button to start play-

back.

To s to p p lay back, press the [DEMO] button again.

Random Song Playback

The order of Song repeat playback via the [DEMO]

button can be changed between numerical order and

random order.

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “PlayMode” (Function

062).

After a few seconds, the current playback mode

appears.

When the DemoGrp is set to “Demo,” this param-

eter cannot be set.

Rotate the dial to select “Random.”

To re t urn to the numerical order, select “Normal.”

Press the [DEMO] button to start play-

back.

To st o p p l ay back, press the [DEMO] button again.

Demo Preset Songs 001–003

Preset All preset Songs

User All User Songs

Download All Songs transferred from a computer

USB

All Songs (MIDI files) in the connected USB

flash drive

AUDIO

All audio Songs in the connected USB flash

drive

• When there are no existing User Songs, Download Songs

or USB Songs in the data, the Demo Songs are played

back.

DemoGrp

061

Hold for longer

than a second.

NOTE

PlayMode

062

Song Settings

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Tempo Setting of the Song

This operation is same as that of the Style and

Groove. Refer to page 61.

Tap Start

This operation is same as that of the Style and

Groove. Refer to page 61.

Song Volume

Press the [FUNCTION] button.

Use the CATEGORY [<<] and [>>] but-

tons to call up “SongVol” (Function 002).

Rotate the dial to set the Song volume

between 000 and 127.

Melody Voice Setting of the

Preset Song

Yo u can change the Melody Voice of the current Pre-

set Song and Song from the external device tempo-

rarily to any other desired Voice.

Press the [SONG] button, select the

desired Preset Song, and then start play-

back (page 28).

Press the [VOICE] button, then rotate the

dial to select the desired Voice.

Hold down the [VOICE] button for longer

than a second to call up “SONG MEL-

ODY VOICE.”

After a few seconds, the Melody Voice of the

Song will be changed to that selected in step 2.

• Tempo of audio Song cannot be changed.

• Song volume can be adjusted while in the Song mode.

NOTE

SongVol

002

100

Song volume

NOTE

• Selecting another Song will cancel the changed Melody

Voice.

• You cannot change the Melody Voice of a User Song.

• Other Voice will be changed depending on Song.

• You cannot change the Voitce of an audio data.

Strings

070

SONG MEL

Hold for longer

than a second.

NOTE

PSR-E463/PSR-EW410 Owner’s Manual

Reference

The Functions

The “Functions” provide access to a range of detailed instrument parameters such as

Tuning, Split Point, Voices and Effects. Find the desired item in the Function List on

pages 66–69, and then follow the instructions below.

Basic Procedure in the Function

Display

Press the [FUNCTION] button.

Press the CATEGORY [<<] and [>>] but-

ton several times until the desired item

appears.

Use the dial, the [+/YES] and [-/NO] but-

tons, or the [0]–[9] number buttons to set

the value of the selected function.

To restore the default value, press the [+/YES] and [-

/NO] buttons simultaneously. The one exception to

this is the MIDI Initial Send function (Function 055),

which is an operation and not a parameter. For this

function, pressing the [+/YES] button executes the

operation while pressing [-/NO] cancels it.

Some Function settings are maintained even if

you turn off the power, and can be transferred to

a computer as Backup Data (page 49).

Function List

SplitPnt

054

009

Current item

Current Function

number

• To exit from a Function display, press the [VOICE],

[STYLE], [SONG] or [GROOVE CREATOR] button.

Direct numeric entry

Press simultane-

ously to recall the

default setting.

•Increment

value by 1

•Execute

•Decrement

value by 1

•Cancel

NOTE

Function Number

Function Display Range/Settings

Default

Value

Description

PSR-

E463

PSR-

EW410

Vol ume

001 001 Style Volume StyleVol 000–127 100 Refer to page 62.

002 002 Song Volume SongVol 000–127 100 Refer to page 65.

003 003 Groove Volume GroovVol 000–127 100 Refer to page 62.

004 004

[AUX IN] Audio

Volume

AuxInVol 000–127 50

Adjusts the volume of audio playback that is input from

the [AUX IN] jack (pages 32, 46).

005 005

[USB TO DEVICE]

[USB TO HOST]

Audio Volume

USBInVol 000–127 100

Adjusts the volume of audio playback that is input from

the [USB TO DEVICE] and [USB TO HOST] terminal

(pages 32, 46).

Overall

006 006 Transpose Transpos -12–12 00 Refer to page 51.

007 007 Tuning Tuning 427.0Hz–453.0Hz 440.0Hz Refer to page 51.

008 008 Pitch Bend Range PBRange 01–12 02

Sets the range over which you can control pitch by using

the [PITCH BEND] wheel (page 51), in semitone incre-

ments.

009 009 Split Point SplitPnt

036–096 (C1–C6;

PSR-E463)/

028–103 (E0–G6;

PSR-EW410)

054 (F#2) Refer to page 62.

010 010 Touch Response TouchRes

1 (Soft), 2 (Medium),

3 (Hard), 4 (Fixed)

2 (Medium) Refer to page 52.

The Functions

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Main Voice (page 20)

011 011 Volume M.Volume 000–127 * Determines the volume of the Main Voice.

012 012 Octave M.Octave -2 – +2 * Determines the octave range for the Main Voice.

013 013 Pan M.Pan

000 (left)–

064 (center)–

127 (right)

Determines the stereo pan position of the Main Voice. A

value of “0” results in the sound being panned full left,

while a value of “127” results in the sound being panned

full right.

014 014 Reverb Depth M.Reverb 000–127 *

Determines how much of the Main Voice’s signal is sent

to the Reverb effect.

015 015 Chorus Depth M.Chorus 000–127 *

Determines how much of the Main Voice’s signal is sent

to the Chorus effect.

016 016 Attack Time M.Attack 000–127 064

Determines how fast the volume of the Main Voice

reaches the Attack level when the note is pressed. The

larger the value, the slower the att

ack rate. The smaller

the value, the faster the attack rate.

017 017 Rele ase Time M.Releas 000–127 064

Determines how fast the volume of the Main Voice falls to

0 when the note is released. The larger the value, the lon-

ger the sustain. The smaller the value, the shorter the

sustain.

018 018 Filte r Cutoff M.Cutoff 000–127 064

Determines the Filter Cutoff Frequency (page 57) of the

Main Voice.

019 019 Filter Resonance M.Reso. 000–127 064

Determines the Filter Resonance (

page 57

) of the Main

Voice.

Dual Voice (page 20)

020 020 Dual Voice D.Voice 001–758 * Selects a Dual Voice.

021 021 Volume D.Volume 000–127 * Determines the volume of the Dual Voice.

022 022 Octave D.Octave -2 – +2 * Determines the octave range for the Dual Voice.

023 023 Pan D.Pan

000 (left)–

064 (center)–

127 (right)

Determines the stereo pan position of the Dual Voice. A

value of “0” results in the sound being panned full left; a

value of “127” results in the sound being panned full right.

024 024 Reverb Depth D.Reverb 000–127 *

Determines how much of the Dual Voice’s signal is sent to

the Reverb effect.

025 025 Chorus Depth D.Chorus 000–127 *

Determines how much of the Dual Voice’s signal is sent to

the Chorus effect.

026 026 Attack Time D.Attack 000–127 064

Determines how f

ast the volume of the Dual Vo

ice

reaches the Attack level when the note is pressed. The

larger the value, the slower the attack rate. The smaller

the value, the faster the attack rate.

027 027 Release Time D.Releas 000–127 064

Determines how fast the volume of the Dual Voice falls to

0 when the note is released. The larger the value, the lon-

ger the sustain. The smaller the value, the shorter the

sustain.

028 028 Filter Cutoff D.Cutoff 000–127 064

Determines the Filter Cutoff Frequency (

page 57

) of the

Dual Voice.

029 029 Filter Resonance D.Reso. 000–127 064

Determines the Filter Resonance (

page 57

) of the Dual

Voice.

Split Voice (page 21)

030 030 Split Voice S.Voice 001–758

054

(FngrBass)

Selects a Split Voice.

031 031 Volume S.Volume 000–127 080 Determines the volume of the Split Voice.

032 032 Octave S.Octave -2 – +2 -1 Determines the octave range for the Split Voice.

033 033 Pan S.Pan

000 (left)–

064 (center)–

127 (right)

064

Determines the stereo pan position of the Split Voice. A

value of “0” results in the sound being panned full left; a

value of “127” results in the sound being panned full right.

034 034 Reverb Depth S.Reverb 000–127 008

Determines how much of the Split Voice’s signal is sent to

the Reverb effect.

035 035 Chorus Depth S.Chorus 000–127 000

Determines how much of the Split Voice’s signal is sent to

the Chorus effect.

Function Number

Function Display Range/Settings

Default

Value

Description

PSR-

E463

PSR-

EW410

The Functions

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Effects

036 036 Reverb Ty p e Reverb 01–13 ** Refer to page 50.

037 037 Chorus Type Chorus 1–6 ** Refer to page 50.

038 038 Master EQ Type MasterEQ

1 (Speaker),

2 (Headphone),

3 (Boost), 4 (Piano),

5 (Bright), 6 (Mild)

1 (Speaker) Refer to page 52.

039 039

Melody

Suppressor

SupprPan L63–C–R63 C

Determines the pan position to be cancelled when the

Melody Suppressor (page 46) is turned on.

DSP (page 24)

040 040 DSP Type DSP Type 01–10 01 Refer to page 24.

Harmony/Arpeggio (page 22)

041 041

Harmony Type/

Arpeggio Type

Harp/Arp 01–26 * Determines the Harmony type or Arpeggio type.

042 042 Harmony Volume HarmVol 000–127 * Determines the volume of the Harmony effect.

043 043 Arpeggio Velocity ARP Velo 1 (Original), 2 (Key)

Depends on

the Arpeg-

gio type

When “Key” is selected, the velocities of Arpeggio play-

back are determined by your playing strength. When

“Original” is selected, the velocities of Arpeggio playback

are determined by the original setting regardless of your

playing strength.

044 044

Arpeggio

Quantize

1 (OFF), 2 (1/8),

3 (1/16)

Depends on

the Arpeg-

gio type

Refer to page 56.

045 045 Pedal Function Pdl Func

1 (Sustain) /

2 (Arp Hold) /

3 (Hold+Sus)

* Refer to page 56.

Scale Tuning (page 53)

046 046 Scale Scale

1 (Equal),

2 (Pure Maj),

3 (Pure min),

4 (Bayat), 5 (Rast)

1 (Equal) Refer to page 53.

047 047 Base Note BaseNote

01 (C), 02 (C#),

03 (D), 04 (Eb),

05 (E), 06 (F),

07 (F

), 08 (G),

09 (A

10 (A),

11 ( B b), 12(B)

01 (C) Refer to page 53.

048 048 Tuning Note TuneNote

01 (C), 02 (C#),

03 (D), 04 (Eb),

05 (E), 06 (F),

07 (F

), 08 (G),

09 (A

10 (A),

11 ( B b), 12(B)

01 (C)

Refer to page 54.

049 049 Tuning Tune -64–63

Depends on

the Scale

MIDI

050 050 Local Control Local ON/OFF ON

Determines whether the instrument’s keyboard controls

the internal tone generator (ON) or not (OFF). When you

record your keyboard performance to a computer app via

MIDI, set this parameter to OFF.

051 051 External Clock ExtClock ON/OFF OFF

Determines whether the instrument synchronizes to the

internal clock (OFF) or an external clock (ON). When you

record your keyboard performance to a computer app via

MIDI, set this parameter to ON.

052 052 Keyboard Out KbdOut ON/OFF ON

Determines whether MIDI messages generated via key-

board performance are transmitted (ON) or not (OFF)

from the [USB TO HOST] terminal. When selecting Sam-

pling Voice, it is not generated regardless of setting.

Function Number

Function Display Range/Settings

Default

Value

Description

PSR-

E463

PSR-

EW410

The Functions

PSR-E463/PSR-EW410 Owner’s Manual

Reference

* The appropriate value is automatically set for each Voice.

** The appropriate value is automatically set for each Style, Song and Groove Creator.

053 053 Style Out StyleOut ON/OFF OFF

Determines whether MIDI messages generated via Style

playback are transmitted (ON) or not (OFF) from the [USB

TO HOST] terminal.

054 054 Song Out SongOut ON/OFF OFF

Determines whether MIDI messages generated via Song

playback are transmitted (ON) or not (OFF) from the [USB

TO HOST] terminal.

055 055 Initial Send InitSend YES/NO -

Allows you to send the data of the panel settings to a

computer. Press [+/YES] to send, or press [-/NO] to can-

cel. When recording a song to computer, perform this

operation first before recording any notes, so that this

instrument will be properly set during playback.

Audio (page 46)

056 056 Audio Loop Back LoopBack ON/OFF ON

Determines whether Audio sound input from the [USB TO

HOST] terminal is returned to the computer or not with

the performance played on the instrument. If you want to

output only the sound played on this instrument to the

computer, set this parameter to OFF.

Sampling (page 33)

057 057 Blank Cut BlankCut ON/OFF ON

Determines whether the blank is cut automatically before

and after Sample.

Metronome (page 21)

058 058

Time Signature

Numerator

TimesigN 00–60 ** Determines the time signature of the Metronome.

059 059

Time Signature

Denominator

TimesigD

Half note, Quarter

note, Eighth note,

Sixteenth note

** Determines the length of each metronome beat.

060 060

Metronome

Volume

MtrVol 000–127 100 Determines the volume of the Metronome.

Demo (page 28)

061 061 Demo Group DemoGrp

1 (Demo) /

2 (Preset) / 3 (User) /

4 (Download) /

5 (USB)

1 (Demo) Refer to page 64.

062 062 Demo Play Mode PlayMode

1 (Normal)

2 (Random)

1 (Normal) Refer to page 64.

Speaker Mute (page 48)

– 063 Speaker Mute SP Mute ON/OFF OFF Refer to page 48.

Auto Power Off (page 16)

063 064

Auto Power Off

Time

AutoOff

OFF, 5/10/15/30/60/

120 (min.)

30 minutes

Specifies the time that will elapse before the instrument’s

power is automatically turned off.

Battery (page 14)

064 065 Battery Type

Battery

Type

1 (Alkaline) /

2 (Ni-MH)

1 (Alkaline)

Selects the type of batteries you have installed to this

instrument.

Language (page 71)

065 066 Language Language English/Japanese English

Determines the language for the Song file names. Deter-

mines the language for the name of the files in the USB

flash drive or the files loaded from a computer.

• The MIDI and Audio settings are designed specifically for convenient use for when an external device such as a computer is connected

to the [USB TO HOST] terminal (page 47).

Function Number

Function Display Range/Settings

Default

Value

Description

PSR-

E463

PSR-

EW410

NOTE

PSR-E463/PSR-EW410 Owner’s Manual

Reference

USB Flash Drive Operations

By connecting a USB flash drive (sold separately) to the [USB TO DEVICE] terminal, you

can save the data created on this instrument, such as User Song and parameter set-

tings. The saved data can be recalled to this instrument again for future use.

• You should use an AC adaptor when executing USB flash drive operations, since battery power may not be reliable enough to

last through these crucial operations. When you try executing certain functions, the “UseAdpt” indication may appear and the

selected function cannot be executed.

IMPORTANT

Precautions when using the [USB TO

DEVICE] terminal

This instrument features a built-in [USB TO DEVICE] ter-

minal. When connecting a USB device to the terminal,

be sure to handle the USB device with care. Follow the

important precautions below.

 Compatible USB devices

• USB flash drive

Other USB devices such as a USB hub, computer key-

board or mouse cannot be used.

The instrument does not necessarily support all com-

mercially available USB devices. Yamaha cannot guar-

antee operation of USB devices that you purchase.

Before purchasing a USB device for use with this instru-

ment, please visit the following web page:

https://download.yamaha.com/

Although USB devices 1.1 to 3.0 can be used on this

instrument, the amount of time for saving to or loading

from the USB device may differ depending on the type of

data or the status of the instrument.

 Connecting a USB device

When connecting a USB device to the [USB TO

DEVICE] terminal, make sure that the connector on the

device is appropriate and that it is connected in the

proper direction.

Using a USB Flash Drive

By connecting the instrument to a USB flash drive, you

can save data you’ve created to the connected device,

as well as read data from the connected device.

 Number of USB flash drives that can be

used

Only one USB flash drive can be connected to the [USB

TO DEVICE] terminal.

 Formatting a USB flash drive

Yo u should format the USB flash drive only with this

instrument (page 72). A USB flash drive formatted on

another device may not operate properly.

 To protect your data (write-protect)

To p r e vent important data from being inadvertently

erased, apply the write-protect provided with each USB

flash drive. If you are saving data to the USB flash drive,

make sure to disable write-protect.

 Turning off the instrument

When turning off the instrument, make sure that the

instrument is NOT accessing the USB flash drive by

playback/recording or file management (such as during

Save, Delete and Format operations). Failu re to do so

may corrupt the USB flash drive and the data.

• For more information about the handling of USB devices,

refer to the owner’s manual of the USB device.

• The rating of the [USB TO DEVICE] terminal is a maxi-

mum of 5V/500mA. Do not connect USB devices having

a rating above this, since this can cause damage to the

instrument itself.

NOTE

• Avoid connecting or disconnecting the USB device

while executing playback/recording and file manage-

ment operations (such as Save, Delete and Format), or

when accessing the USB device. Failure to observe

this may result in “freezing” of the operation of the

instrument or corruption of the USB device and the

data.

• When connecting then disconnecting the USB device

(and vice versa), make sure to wait a few seconds

between the two operations.

• When connecting a USB cable, make sure that the length

is less than 3 meters. Do not connect an extension cable.

• The format operation overwrites any previously exist-

ing data. Make sure that the USB flash drive you are

formatting does not contain important data.

NOTICE

NOTE

NOTICE

USB Flash Drive Operations

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Connecting a USB Flash Drive

Connect a USB flash drive to the [USB

TO DEVICE] terminal, and wait until

“USB” appears on the left corner of the

display.

The “USB” indication confirms that the connected

USB flash drive has been mounted or recog-

nized.

Hold down the [FUNCTION] button for

longer than a second to call up the File

Control display.

 If “UnFormat” followed by “Format?”

appears:

This indicates that the connected USB flash

drive requires formatting. Execute the Format

operation by following the instructions starting

with step 2 on page 72.

Use the CATEGORY [<<] and [>>] but-

tons to call up the desired File Control

function, then execute it.

For details, refer to the table on the right.

File Control Display List

• Before using a USB flash drive, be sure to read “Precautions

when using the [USB TO DEVICE] terminal” on page 70.

• Messages may appear on the display during File Control pro-

cedures to aid in operation. Refer to the Message List on

page 77 for details.

The File Control display cannot be called up in the follow-

ing situations.

• During playback of Style, Groove, Song, Quick Sam-

pling Mode, or Audio mode.

• When “USB” does not appear even if you have con-

nected a USB flash drive to the [USB TO DEVICE]

terminal.

• No sound will be produced if the keyboard is played

while the File Control display is showing, and only but-

tons related to File Control operations will be active.

NOTE

Mounting (flashes) Mounted (lights)

SaveSMPL

Hold for longer

than a second.

NOTE

Display File Control function Page

SaveSMPL

Saving a Sample to a USB Flash

Drive

LoadSMPL

Loading a Sample from a USB

Flash Drive

Del SMPL

Deleting a Sample in a USB Flash

Drive

DelAUDIO

Deleting an Audio Song in a USB

Flash Drive

Save SMF

Saving a User Song as SMF to a

USB Flash Drive

Del SMF

Deleting a SMF in a USB Flash

Drive

Save USR

Saving a User Data to a USB Flash

Drive

Load USR

Loading a User Data from a USB

Flash Drive

Del USR

Deleting a User Data from a USB

Flash Drive

Load STY Loading a Style File 75

Format? Formatting a USB Flash Drive72

Exit? Exiting from a File Control Display 77

• You can also exit from a File Control display simply by

pressing the [FUNCTION] button.

Valid file locations in the USB flash drive for

Song playback (page 28)

Song title display language

File names containing Japanese katakana characters

will only be properly displayed if the instrument’s display

language is set to “Japanese.” All display information

other than file names will be displayed in English even if

“Japanese” is selected. For details, refer to page 69

Function 065 (PSR-E463)/Function 066 (PSR-EW410).

NOTE

Can be selected/

played.

Cannot be selected/

played.

USB flash drive (Root)

Song

File

Song

File

Song

File

Song

File

• If you manage the Song files in the USB flash drive by

using a computer, etc., make sure to store the data

either in the USB flash drive’s root directory or a first-

level/second-level folder in the root directory. Data

stored in third-level-folders created inside a second-

level folder cannot be selected and played by this

instrument.

IMPORTANT

USB Flash Drive Operations

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Formatting a USB Flash Drive

The Format operation lets you prepare commercially

available USB flash drives for use with this instru-

ment.

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

Use the CATEGORY [<<] and [>>] but-

tons to call up the “Format?” message.

Press the [0/EXECUTE] button.

A confirmation message will appear. To cancel

the operation, press the [-/NO] button.

Press the [0/EXECUTE] button again or

the [+/YES] button to execute the Format

operation.

After a while, a message indicating completion of

the operation appears, and the “USER FILES”

folder will be created in the USB flash drive.

Press the [FUNCTION] button to exit

from the File Control display.

Saving User Data to a USB Flash

Drive

User data is comprised of the following items.

• All 10 User Songs (page 38)

•Styles which have been transferred from a com-

puter and then loaded to Style numbers 221–

230 (page 75).

• All Registration Memory settings (page 44)

The User data can be saved as a single “User File”

(.usr) to a USB flash drive.

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

Use the CATEGORY [<<] and [>>] but-

tons to call up “Save USR.”

Press the [0/EXECUTE] button.

Target User file names appear on the display as

“USER***” (***: number). If desired, rotate the dial

to select a different file name from “USER001”–

“USER100.”

Press the [0/EXECUTE] button again.

A confirmation message will appear. To cancel

the operation, press the [-/NO] button.

• The format operation overwrites any previously existing

data. Make sure that the USB flash drive you are formatting

does not contain important data.

• The Format operation cannot be cancelled during exe-

cution. Never turn off the power or disconnect the

USB flash drive during the operation. Doing so may

result in data loss.

NOTICE

Format?

NOTICE

• For detail on saving Sample, refer to page 34.

• The extension (.usr) of the User File will not be shown on the

display of this instrument. Confirm the extension on the com-

puter display when connecting the USB flash drive to a com-

puter.

Overwriting existing files

If a file that already contains data is selected as the

target user file, “OverWr?” will appear on the display.

NOTE

Save USR

USER001

USB Flash Drive Operations

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Press the [0/EXECUTE] button again, or

the [+/YES] button to execute the Save

operation.

After a while, a message indicating completion of

the operation appears, and a User file (.usr) will

be saved in a “USER FILES” folder which will

automatically be created on the USB flash drive.

Press the [FUNCTION] button to exit

from the File Control display.

Saving a User Song as SMF to a

USB Flash Drive

A User Song can be converted to SMF (Standard

MIDI File) format 0 and saved to a USB flash drive.

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

Use the CATEGORY [<<] and [>>] but-

tons to call up “Save SMF.”

Press the [0/EXECUTE] button.

Target User Song names appear on the display

as “USER**” (**: number 1–10). If desired, rotate

the dial to select a different User Song from

“USER01”–“USER10” then press the [0/EXE-

CUTE] button.

Press the [0/EXECUTE] button again.

Target file names on the USB flash drive appear

on the display as “USER***” (***: number 1–100).

If desired, rotate the dial to select the different file.

• The Save operation cannot be cancelled during execu-

tion. Never turn off the power or disconnect the USB

flash drive during the operation. Doing so may result

in data loss.

• The amount of time required for this operation may vary

depending on the condition of the USB flash drive.

• If you want to recall the User file (.usr) to this instrument

again, execute the Load operation (page 74).

NOTICE

NOTE

SMF (Standard MIDI File) format

With this format, various events via the keyboard perfor-

mance such as note on/off and Voice selection will be

recorded as MIDI data. The SMF Format 0 and Format

1 are available. A large number of MIDI devices are

compatible with SMF Format 0, and most commercially

available Song files (MIDI files) are provided in SMF For-

mat 0.

• If the size of a converted SMF is too large, such as a User

Song recorded with Groove data, it cannot be played back on

this instrument. We recommend using Audio recording.

• The DSP effect (page 24) cannot be converted to SMF for-

mat.

• The Transpose setting on this instrument is not included in the

data.

NOTE

Save SMF

User 1

SONG001

USB Flash Drive Operations

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Press the [0/EXECUTE] button again.

A confirmation message will appear. To cancel

the operation, press the [-/NO] button.

Press the [0/EXECUTE] button again, or

the [+/YES] button to execute the Save

operation.

After a while, a message indicating completion of

the operation appears, and a User Song will be

saved (in SMF format 0) to a “USER FILES”

folder, automatically created on the USB flash

drive.

Press the [FUNCTION] button to exit

from the File Control display.

Loading User Data from a USB

Flash Drive

A User data (page 72) saved as a User file (.usr) to

the USB flash drive can be loaded to this instrument.

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

Use the CATEGORY [<<] and [>>] but-

tons to call up “Load USR.”

Press the [0/EXECUTE] button.

User file names on the USB flash drive appear on

the display as “USER***” (***: number). As

desired, rotate the dial to select a different User

file.

Press the [0/EXECUTE] button again.

A confirmation message will appear. To cancel

the operation, press the [-/NO] button.

Press the [0/EXECUTE] button again, or

the [+/YES] button to execute the Load

operation.

After a while, a message indicating completion of

the operation appears.

Overwriting existing files

If a file that already contains data is selected, an

overwrite confirmation message will appear.

• The Save operation cannot be cancelled during execu-

tion. Never turn off the power or disconnect the USB

flash drive during the operation. Doing so may result

in data loss.

• The amount of time required for this operation may vary

depending on the condition of the USB flash drive.

• If a Groove has been recorded to the User Song, the

Save operation cannot be executed by pressing the [0/

EXECUTE] button or the [+/YES] button, and “Can’tUse”

appears on the display.

NOTICE

NOTE

• Loading a User file will overwrite and erase the existing

data, including all 10 User Songs, Style data loaded to the

Style numbers 236–245, and all the Registration Memory

settings. Save important data you want to keep to a sepa-

rate USB flash drive before loading a User file.

• Note that User files should be saved in the “USER FILES”

folder on the USB flash drive. Files saved outside this

folder cannot be recognized.

• About loading Sample, refer to page 35.

• The Load operation cannot be cancelled during execu-

tion. Never turn off the power or disconnect the USB

flash drive during the operation. Doing so may result

in data loss.

NOTICE

IMPORTANT

NOTE

Load USR

USER001

NOTICE

USB Flash Drive Operations

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Press the [FUNCTION] button to exit

from the File Control display.

Confirm that the data has been properly

loaded by calling up the User Song, one

of the Styles 236–245, and/or the Regis-

tration Memory settings.

Loading a Style File

Style data created on another instrument or a com-

puter can be loaded to the Style numbers 236–245,

and you can play them in the same way as the inter-

nal preset Styles. The following two Load operations

are available.

• Loading of a Style file (.sty) saved on the root

directory on the USB flash drive

• Loading of a Style file (.sty) transferred from a

computer via the Musicsoft Downloader and stored

in the internal memory of this instrument

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

Use the CATEGORY [<<] and [>>] but-

tons to call up the “Load STY” message.

Press the [0/EXECUTE] button.

The name of a Style file in the USB flash drive or

internal memory of this instrument will appear on

the display. If desired, rotate the dial to select a

different Style file.

Press the [0/EXECUTE] button again.

“Load To? ***” (***: 236–245) appears on the dis-

play as the Load destination. If desired, rotate the

dial to select a different number.

Press the [0/EXECUTE] button again.

A confirmation message will appear. To cancel

the operation, press the [-/NO] button.

Press the [0/EXECUTE] button again, or

the [+/YES] button to execute the Load

operation.

After a while, a message indicating completion of

the operation appears.

Press the [STYLE] button, rotate the dial

to select a Style from 236–245, and then

try playing it back.

• For instructions on transferring a Style file from a computer via

the Musicsoft Downloader, refer to the online PDF manual

(page 11) “Computer-related Operations.” After data transfer,

load the Style data to one of the Style numbers 236–245 to

enable playback.

• Loading a Style file will overwrite and erase the existing

data of the destination number. Save important data you

want to keep to a separate USB flash drive before loading.

NOTE

NOTICE

Load STY

• The Load operation cannot be cancelled during execu-

tion. Never turn off the power or disconnect the USB

flash drive during the operation. Doing so may result

in data loss.

DiscoFox

USb

Load To?

236

NOTICE

USB Flash Drive Operations

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Deleting a User File in the USB

Flash Drive

User Files (.usr) in the root directory of the USB flash

drive can be deleted.

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

Use the CATEGORY [<<] and [>>] but-

tons to call up the “Del USR” message.

Press the [0/EXECUTE] button.

User file names in the USB flash drive appear on

the display as “USER****” (****: number). If

desired, rotate the dial to select a different User

file.

Press the [0/EXECUTE] button again.

A confirmation message will appear. To cancel

the operation, press the [-/NO] button.

Press the [0/EXECUTE] button again, or

the [+/YES] button to execute the Delete

operation.

After a while, a message indicating completion of

the operation appears.

Press the [FUNCTION] button to exit

from the File Control display.

Deleting an SMF File in the USB

Flash Drive

Yo u can delete a SMF file that has been saved in the

USB flash drive via the Save SMF operation (page

73).

Hold the [FUNCTION] button for longer

than a second to call up the File Control

display.

Use the CATEGORY [<<] and [>>] but-

tons to call up “Del SMF.”

Press the [0/EXECUTE] button.

SMF file names in the USB flash drive appear on

the display as “SONG****” (****: number).

If desired, rotate the dial to select a different SMF

file.

Press the [0/EXECUTE] button again.

A confirmation message will appear. To cancel

the operation, press the [-/NO] button.

Press the [0/EXECUTE] button again, or

the [+/YES] button to execute the Delete

operation.

After a while, a message indicating completion of

the operation appears.

Press the [FUNCTION] button to exit

from the File Control display.

• Only User files (.usr) saved in the “USER FILES” folder on

the USB flash drive can be deleted. Files outside this folder

cannot be recognized.

• The Delete operation cannot be cancelled during exe-

cution. Never turn off the power or disconnect the

USB flash drive during the operation. Doing so may

result in data loss.

IMPORTANT

Del USR

USER001

NOTICE

• Only SMF files (.mid) saved in the “USER FILES” folder on

the USB flash drive can be deleted. Files outside this folder

cannot be recognized. This operation applies only to file

names having the format “SONG***” (***: 001–100).

• The Delete operation cannot be cancelled during exe-

cution. Never turn off the power or disconnect the

USB flash drive during the operation. Doing so may

result in data loss.

IMPORTANT

Del SMF

SONG001

NOTICE

USB Flash Drive Operations

PSR-E463/PSR-EW410 Owner’s Manual

Reference

Exiting from a File Control

Display

To exit from the File Control display, press the

[FUNCTION], [VOICE], [STYLE], [SONG] or

[GROOVE CREATOR] button.

Yo u can also exit from the File Control function mode

as follows:

Use the CATEGORY [<<] and [>>] but-

tons to call up the “Exit?” message.

Press the [0/EXECUTE] button to exit

from the File Control display.

Message List

Exit?

Message Comment

Can’tUse

Indicates that the file control function is

currently unavailable since the USB flash

drive is being accessed.

Complet.

Indicates completion of the corresponding

operation, such as data saving or trans-

mission.

Data Err

Displayed when the user song contains

invalid data.

Disk Ful

Displayed when saving data cannot be

executed since the memory has become

full. Delete any unnecessary data or use

another USB flash drive.

Error

Displayed when a file error or operational

error occurs.

File Ful

Displayed when saving of data cannot be

executed because the total number of files

exceeds the capacity. Delete any unnec-

essary data or use another USB flash

drive.

no data There is no data in the memory.

no file There is no file in the memory.

Ovr

(Fl

ashes

)

Communication with the USB flash drive

has been shut down because of overcur-

rent to the USB flash drive. Disconnect the

USB flash drive from the [USB TO

DEVICE] terminal, then turn on the power

of the instrument.

Protect

Displayed when trying to save or delete

data on a protected USB flash drive, or

formatting a protected USB flash drive.

Set protect to off and try again.

UnFormat

Displayed when connecting an unformat-

ted USB flash drive.

UseAdpt

USB flash drive save, delete, and format

operations cannot be performed when the

instrument is being powered from battery.

Use an AC adaptor.

PSR-E463/PSR-EW410 Owner’s Manual

Appendix

Troubleshooting

Refer to the “Message List” on pages 42, 77 as required.

Problem Possible Cause and Solution

When the instrument is turned on or off, a popping

sound is temporarily produced.

This is normal and indicates that the instrument is receiving electri-

cal power.

When the instrument is turned on, power is turned off

suddenly and unexpectedly.

This is normal. If an AC adaptor other than the one specified is

used, power may be turned off suddenly and unexpectedly.

When using a mobile phone, noise is produced

Using a mobile phone in close proximity to the instrument may pro-

duce interference. To prevent this, turn off the mobile phone or use

it further away from the instrument

The instrument is automatically turned off even if no

operation is done.

This is normal. This occurs due to the Auto Power Off function

(page 16).

•The volume

is to

o soft.

•The sound quality is poor.

• The Style/Groove/Song/Arpeggio stops unexpectedly

or will not play.

• The recorded data of the song, etc. does not play cor-

rectly.

• The LCD display suddenly goes dark, and all panel set-

tings are reset.

•The instrument turns off when a USB flash drive is con-

nected.

The batteries are low or dead. Replace all six batteries with com-

pletely new ones or completely recharged ones, or use the AC

adaptor.

No sound is produced even when the keyboard is

played, or a Song, Style, or Groove is being played back.

Check whether a set of headphones or an audio cable is connected

to the [PHONES/OUTPUT], or not. When such a connection is

made, no sound is output from the speaker of this instrument.

(PSR-EW410) Check the on/off status of the Speaker Mute setting

(page 48). Make sure to set to OFF.

Check the on/off status of the Local Control (page 68). Normally,

set this parameter to ON.

The

footswitch (f

or sustain) seems to produce the oppo-

site effect. For example, pressing the footswitch cuts off

the sound and releasing it sustains the sounds.

The polarity of the footswitch is reversed. Make sure that the foot-

switch plug is properly connected to the SUSTAIN jack before turn-

ing on the power.

Not all of the Voices seem to sound, or the sound seems

to be cut off, when playing the keyboard, Arpeggio, Style

or Song or Groove Creator.

Yo u have exceeded 48 simultaneous notes, which is the maximum

polyphony (the maximum amount of notes that can be played

simultaneously) of this instrument. If the Main, Dual, and Split

Voices are being used along with playback of Arpeggio, Style,

Groove or Song, some notes/sounds may be omitted (or “stolen”).

The sound

of the Voice changes from note to note.

This is no

rmal. The tone generation method uses multiple record-

ings (samples) of an instrument across the range of the keyboard;

thus, the actual sound of the Voice may be slightly different from

note to note.

The keyboard performance and playback of Style/Song/

Groove Creator produces an unexpected or inappropri-

ate sound, and cannot be restored to the normal status.

Using the Knobs can produce dramatic changes in the sound, but

may also produce unexpected or undesired sounds. If you want to

restore the original, normal sound before being changed by the

Knobs, press the [DSP] button to turn DSP off, change the Voice,

Style, Groove or Song, or press the [PORTABLE GRAND] button to

reset the panel settings.

The Style, Song or Groove Creator does not start even

when the [START/STOP] button is pressed. The Arpeg-

gio does not start even when the note is pressed with the

rpeggio turn

ed on.

Check the on/off status of the External Clock (page 68). Normally,

set this parameter to OFF.

The volume of the Style, Song or Groove Creator is too

low.

Check the volume setting in the Functions (pages 62 and 65).

The chords played in the left hand area cannot be recog-

nized even when ACMP is turned on.

Check the Split Point setting (page 62). Set this to an appropriate

value.

Style parts other than the Rhythm part produce no

sound.

Check the on/off status of the ACMP (page 26). Make sure to turn

ACMP on.

The ACMP indicator does not appear on the display

when the [ACMP ON/OFF] button is pressed.

Check the on/off status of the [STYLE] lamp. When using a Style,

press the [STYLE] button to turn on the [STYLE] lamp.

Appendix

PSR-E463/PSR-EW410 Owner’s Manual

Appendix

Specifications

PSR-E463 PSR-EW410

Product Name Digital Keyboard

Size/Weight

Dimensions (W x D x H)

946mm x 404mm x 139mm

(37-1/4” x 15-7/8” x 5-1/2”)

1179mm x 413mm x 138mm

(46-7/16” x 16-1/4” x 5-7/16”)

Weight

6.6 kg (14 lbs., 9 oz.)

(not including batteries)

8.4 kg (18 lbs., 8 oz.)

(not including batteries)

Control

Interface

Keyboard

Number of Keys 61 76

Touch Response Soft, Medium, Hard, Fixed Soft, Medium, Hard, Fixed

Other

Controllers

Pitch Bend

Wheel

Ye s

KnobsYes

Panel Language English

Voices

Tone

Generation

Tone Generation

Technology

AWM Stereo Sampling

Polyphony (max.) 48

Preset

Number of

Voic es

758

(237 Panel Voices + 24 Drum/SFX kits + 40 Arpeggio + 457 XGlite voices)

Compatibility GM, XGlite

Effects

Types

Reverb 12

Chorus5

Master EQ 6

DSP 10

Functions

Dual Y

Split Yes

Harm

ony 26

Arpeggio 150

Melody

Suppressor

Ye s

Crossfade Yes

Accompaniment

Styles

Preset

Number of

Styles

235

Fingering Multi finger

Style Control

ACMP ON/OFF, SYNC START, SYNC STOP, START/STOP,

INTRO/ENDING/rit., MAIN/AUTO FILL, TRACK ON/OFF

External Styles 10

Other Features

One Touch

Setting (OTS)

Ye s

Compatibility Style File Format (SFF)

Groove Creator Preset

Number of

Grooves

Number of

Sections

5 (4 Sections + 1 Musical Climax/Ending)

Songs

(MIDI)

Preset

Number of

Preset Songs

Download

Number of

Songs

Recording

Number of

Songs

Number of

Tra ck s

6 (5 Melody + 1 Style/Groove Creator)

Data Capacity Approx. 19,000 notes (when only “melody” tracks are recorded)

Format

Playback SMF (Formats 0 & 1)

Recording Original File Format (SMF 0 conversion function)

USB Audio

Recorder

Recording Time (max.) 80 minutes (approx. 0.9 GB) per Song

rmat

Playbac

k WAV(44.1 kHz, 16 bit, stereo)

Recording WAV(44.1 kHz, 16 bit, stereo)

Quick Sampling

Sampling Type Normal, Oneshot, Loop

Samples (Preset/User) 5 7

Sampling Time Approx. 9.6sec.

Sampling Sources AUX IN

Sampling Format Original File Format (16 bit, stereo)

Sampling Rate 44.1 kHz

Functions

USB audio interface 44.1 kHz, 16 bit, stereo

Registration

Memory

Number of

Buttons

4 (x 8 banks)

Overall

Controls

Metronome Yes

Tempo Range 11 – 280

Transpose -12 to 0, 0 to +12

Tuning 427.0 – 440.0 – 453.0 Hz (approx. 0.2Hz increments)

Scale Type 5 types

Miscellaneous PIANO Button Yes

Specifications

PSR-E463/PSR-EW410 Owner’s Manual

Appendix

* The contents of this manual apply to the latest specifications as of the publishing date. To ob tain the latest manual, access the Yamaha website then

download the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your

Yamaha dealer.

Storage and

Connectivity

Storage

Internal Memory Approx. 1.73 MB

External Drives USB flash drive

Connectivity

USB TO HOST, USB TO DEVICE,

DC IN 12V, Headphones/Output,

Sustain Pedal, AUX IN (Stereo-mini)

USB TO HOST, USB TO DEVICE,

DC IN 16V, Headphones, Sustain Pedal,

AUX IN (Stereo-mini),

OUTPUT (L/L+R, R)

Sound System

Amplifiers 6W+6W 12W+12W

Speakers 12cm x 2

Power Supply

AC Adaptor

PA-150 or an equivalent recommended

by Yamaha

PA-300C or an equivalent recommended

by Yamaha

Batteries

Six “AA” size alkaline (LR6),

manganese (R6) or

Ni-MH rechargeable (HR6) batteries

Six “D” size alkaline (LR20),

manganese (R20) or

Ni-MH rechargeable (HR20) batteries

Power Consumption 8 W (When using PA-1

50 AC adaptor) 11 W (When using PA-300C AC adaptor)

Auto Power Off Yes

Included Accessories

•Owner’s Manual

• AC adaptor* (PA-150 or an equivalent

recommended by Yamaha)

* May not be included depending on your

area. Check with your Yamaha dealer.

•Music Rest

• Online Member Product Registration

•Owner’s Manual

• AC adaptor* (PA-300C or an equivalent

recommended by Yamaha)

* May not be included depending on your

area. Check with your Yamaha dealer.

•Music Rest

• Online Member Product Registration

Separately Sold Accessories

(May not be available depending on your area.)

• AC adaptor: PA-150 or an equivalent

recommended by Yamaha

•Keyboard Stand: L-2C

• Headphones: HPH-150/HPH-100/HPH-

• Footswitch: FC4A/FC5

• Wireless MIDI adaptor: UD-BT01

• AC adaptor: PA-300C or an equivalent

recommended by Yamaha

•Keyboard Stand: L-6

• Headphones: HPH-150/HPH-100/HPH-

•Subwoofer: KS-SW100

• Footswitch: FC4A/FC5

• Wireless MIDI adaptor: UD-BT01

PSR-E463 PSR-EW410

PSR-E463/PSR-EW410 Owner’s Manual

Appendix

Index

A-B Repeat ..............................29

AC adaptor ..............................14

Accessories ............................. 10

ACMP ......................................26

Arpeggio ............................22, 56

Arpeggio Quantize...................56

Arpeggio Type .........................23

Arpeggio Velocity.....................23

Attack.......................................57

Audio Device ...........................46

Audio Loop Back .....................69

Auto Accompaniment...............26

Auto Accompaniment area ......26

Auto Power Off................... 16, 69

AUX IN...............................31, 46

Background Music ...................64

Backup.....................................49

Backup Clear...........................49

Base Note................................53

Battery ..................................... 14

Battery Type............................. 15

Blank Cut.................................69

Chord Type ..............................63

Chorus .....................................57

Chorus Type ............................50

Computer.................................47

Computer-related Operations .. 11

Connection ..............................45

Cutoff .......................................57

Data List .................................. 11

Del SMF ..................................71

Del SMPL ................................71

Del USR ..................................71

DelAUDIO ................................71

Demo Song .............................28

Display............................... 12, 19

DSP ...................................24, 57

DSP Type.................................24

Dual Voice .........................20, 55

ENDING ..................................59

EQ (Equalizer) .........................52

External Clock .........................68

Fast Forward............................28

Fast Reverse............................28

File Control display ..................71

FILL .........................................59

Fine Tuning ..............................51

Flash Clear ..............................49

Footswitch..........................45, 56

Formatting .........................70, 72

Fu nction...................................66

Groove..................................... 59

Groove Creator........................ 30

Harmony ................................. 22

Harmony Type ......................... 23

Headphones............................ 45

Initial Send .............................. 69

Initialization ............................. 49

INTRO ..................................... 59

iPhone/iPad Connection Manual

..11

Keyboard Out .......................... 68

Keyboard Stand....................... 17

Knobs................................ 25, 57

Language .......................... 69, 71

Load STY ................................ 71

Load USR................................ 71

LoadSMPL .............................. 71

Local Control ........................... 68

Loop ........................................ 31

MAIN ....................................... 59

Main Voice............................... 20

Master Volume ........................ 16

Melody Suppressor ................. 46

Melody Voice........................... 65

Message List ............... 41, 42, 77

Metronome .............................. 21

MIDI......................................... 27

MIDI Basics ..............................11

MIDI Reference ........................11

Music Rest .............................. 10

MUSICAL CLIMAX .................. 30

Normal .................................... 31

Octave ..................................... 67

One Touch Setting (OTS) .. 20, 51

One-shot ................................. 31

Output ..................................... 48

Pan .......................................... 67

Pause ...................................... 28

Pedal ....................................... 45

Pitch ........................................ 51

Pitch Bend Range ................... 66

Power ...................................... 16

Quick Sampling ....................... 31

Random................................... 64

Recording.......................... 38, 41

Registration Memory............... 44

Release................................... 57

Repeat .................................... 29

Resonance.............................. 57

Retrigger ................................. 61

Retrigger Rate......................... 58

Reverb .................................... 57

Reverb Type............................ 50

Sample Type ........................... 31

Sample Zone .......................... 31

Sampling................................. 31

Save SMF ............................... 71

Save USR ............................... 71

SaveSMPL .............................. 71

Scale....................................... 53

Sections ............................ 59, 61

Smart Device .......................... 47

Song .................................. 27, 64

Song Book ...............................11

Song Out................................. 69

Speaker .................................. 48

Specifications.......................... 79

Split Point.......................... 21, 62

Split Voice ......................... 21, 55

Stop Accompaniment.............. 62

Style.................................. 26, 59

Style Out................................. 69

Sustain.................................... 45

Synchro Stop .......................... 60

Tap Start ........................... 61, 65

Tempo ......................... 21, 61, 65

Time Signature........................ 21

Touch Response ..................... 52

Track ..................... 29, 38, 39, 60

Transpose ............................... 51

Troubleshooting....................... 78

Tuning ............................... 51, 54

USB Flash Drive ..................... 70

USB TO DEVICE .................... 70

USB TO HOST........................ 47

Voice ................................. 20, 55

Volume.....................................16

Volume (AUX IN)..................... 66

Volume (Groove Creator) ........ 62

Volume (Harmany).................. 23

Volume (Metronome) .............. 22

Volume (Song) ........................ 65

Volume (Style) ........................ 62

Volume (USB TO DEVICE)..... 66

Volume (USB TO HOST) ........ 66

Volume (Voice)........................ 67

Volume Balance...................... 58

PSR-E463/PSR-EW410 Owner’s Manual

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så länge

som den ar ansluten till vägguttaget, även om själva apparaten

har stängts av.

ADVARSEL: Netspændingen til dette apparat er IKKE

afbrudt, sålænge netledningen sidder i en stikkontakt, som er

tændt — også selvom der er slukket på apparatets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita

koko laitetta verkosta.

(standby)

Entsorgung leerer Batterien (nur innerhalb

Deutschlands)

Leisten Sie einen Beitrag zum Umweltschutz. Verbrauchte

Batterien oder Akkumulatoren dürfen nicht in den Hausmüll. Sie

können bei einer Sammelstelle für Altbatterien bzw. Sondermüll

abgegeben werden. Informieren Sie sich bei Ihrer Kommune.

(battery)

(weee_battery_eu_en_02)

Information for users on collection and disposal of old equipment and used batteries:

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries

should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in

accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal

service or the point of sale where you purchased the items.

or busines

s users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union:

These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask

for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the EU Battery

Directive for the chemical involved.

PSR-E463/PSR-EW410 Owner’s Manual

LIMITED 1-YEAR WARRANTY ON

PORTABLE KEYBOARDS

(NP, PSRE, PSREW, PSRF, EZ, DGX230, DGX530, YPG AND YPT SERIES)

Thank you for selecting a Yamaha product. Yamaha products are designed and manufactured to provide a high level of defect-free

performance. Yamaha Corporation of America (“Yamaha”) is proud of the experience and craftsmanship that goes into each and every

Yamaha product. Yamaha sells its products through a network of reputable, specially authorized dealers and is pleased to offer you, the

Original Owner, the following Limited Warranty, which applies only to products that have been (1) directly purchased from Yamaha’s

authorized dealers in the fifty states of the USA and District of Columbia (the “Warranted Area”) and (2) used exclusively in the Warranted

Area. Yamaha suggests that you read the Limited Warranty thoroughly, and invites you to contact your authorized Yamaha dealer or

Yamaha Customer Service if you have any questions.

Coverage: Yamaha will, at its option, repair or replace the product covered by this warranty if it becomes defective, malfunctions or

otherwise fails to conform with this warranty u nder normal use and service during the term of this warranty, without charge for labor or

materials. Repairs may be performed using new or refurbished parts that meet or exceed Yamaha specifications for new parts. If Yamaha

elects to replace the product, the replacement may be a reconditioned unit. You will be responsible for any installation or removal charges

and for any initial shipping charges if the product(s) must be shipped for warranty service. However, Yamaha will pay the return shipping

charges to any destination within the USA if the repairs are covered by the warranty. This warranty does not cover (a) damage,

det

erioration

or malfunction resulting from accident, negligence, misuse, abuse, improper installation or operation or failure to follow

instructions according to the Owner’s Manual for this product; any shipment of the product (claims must be presented to the carrier); repair

or attempted repair by anyone other than Yamaha or an authorized Yamaha Service Center; (b) any unit which has been altered or on

which the serial number has been defaced, modified or removed; (c) normal wear and any periodic maintenance; (d) deterioration due to

perspiration, corrosive atmosphere or other external causes such as extremes in temperature or humidity; (e) damages attributable to

power line surge or related electrical abnormalities, lightning damage or acts of God; or (f) RFI/EMI (Interference/noise) caused by

improper grounding or the improper use of either certified or uncertified equipment, if applicable. Any evidence of alteration, erasing or

forgery of proof-of-purchase documents will cause

this warr

anty to be void. This warranty covers only the Original Owner and is not

transferable.

In Order to Obtain Warranty Service: Warranty service will only be provided for defective products within the Warranted Area.

Contact your local authorized Yamaha dealer who will advise you of the procedures to be followed. If this is not successful, contact

Yamaha at the address, telephone number or website shown below. Yamaha may request that you send the defective product to a local

authorized Yamaha Servicer or authorize return of the defective product to Yamaha for repair. If you are uncertain as to whether a dealer

has been authorized by Yamaha, please contact Yamaha’s Service Department at the number shown below, or c

heck Yamaha’s website at

www.Yama

ha.com

. Product(s) shipped for service should be packed securely and must be accompanied by a detailed explanation of the

problem(s) requiring service, together with the original or a machine reproduction of the bill of sale or other dated, proof-of-purchase

document describing the product, as evidence of warranty coverage. Should any product submitted for warranty service be found ineligible

therefore, an estimate of repair cost will be furnished and the repair will be accomplished only if requested by you and upon receipt of

payment or acceptable arrangement for payment.

Limitation of Implied Warranties and Exclusion of Damages: ANY IMPLIED WARRANTIES, INCLUDING

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE

APPLICABLE PERIOD OF TIME SET FORTH ABOVE. YAMAHA SHALL NOT BE RESPONSIBLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR FOR DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE, DAMAGE TO ANY OTHER

EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE OR INTERRUPTION OF PERFORMANCES OR ANY CONSEQUENCES.

YAMAHA’S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, AT

YAMAHA’S OPTION. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY

NOT APPLY TO YOU. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This

is the only express warranty applicable to the product specified herein; Yamaha neither assumes nor authorizes anyone to assume for it

any other express warranty.

If you have any questions about service received or if you need assistance in locating an authorized Yamaha Servicer, please contact:

CUSTOMER SERVICE

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, California 90620-1373

Telephone: 800-854-1569

www.yamaha.com

Do not return any product to the above address without a written Return Authorization issued by YAMAHA.

MEMO

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Toronto, Ontario M1S 3R1,

Canada

Tel: +1-416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620,

U.S.A.

Tel: +1-714-522-9011

MEXICO

Yamaha de México, S.A. de C.V.

Av. Insurgentes Sur 1647 Piso 9, Col. San José

Insurgentes, Delegación Benito Juárez, México,

D.F., C.P. 03900, México

Tel: +52-55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B –

Vila Olímpia – CEP 04551-010 – São Paulo/SP,

Brazil

Tel: +55-11-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.,

Sucursal Argentina

Olga Cossettini 1553, Piso 4 Norte,

Madero Este-C1107CEK,

Buenos Aires, Argentina

Tel: +54-11-4119-7000

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Edif. Torre Banco General, F7, Urb. Marbella,

Calle 47 y Aquilino de la Guardia, Panama,

P.O.Box 0823-05863, Panama, Rep.de Panama

Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND

Yamaha Music Europe GmbH (UK)

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, U.K.

Tel: +44-1908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH, Branch

Switzerland in Thalwil

Seestrasse 18a, 8800 Thalwil, Switzerland

Tel: +41-44-3878080

AUSTRIA/CROATIA/

CZECH REPUBLIC

HUNGARY/ROMANIA/SLOVAKIA/

SLOVENIA

Yamaha Music Europe GmbH, Branch Austria

Schleiergasse 20, 1100 Wien, Austria

Tel: +43-1-60203900

POLAND

Yamaha Music Europe GmbH

Sp.z o.o. Oddział w Polsce

ul. Wielicka 52, 02-657 Warszawa, Poland

Tel: +48-22-880-08-88

BULGARIA

Dinacord Bulgaria LTD.

Bul.Iskarsko Schose 7 Targowski Zentar Ewropa

1528 Sofia, Bulgaria

Tel: +359-2-978-20-25

MALTA

Olimpus Music Ltd.

Valletta Road, Mosta MST9010, Malta

Tel: +356-2133-2093

NETHERLANDS/BELGIUM/

LUXEMBOURG

Yamaha Music Europe, Branch Benelux

Clarissenhof 5b, 4133 AB Vianen, The Netherlands

Tel: +31-347-358040

FRANCE

Yamaha Music Europe

7 rue Ambroise Croizat, Zone d'activités de Pariest,

77183 Croissy-Beaubourg, France

Tel: +33-1-6461-4000

ITALY

Yamaha Music Europe GmbH, Branch Italy

Via Tinelli N.67/69 20855 Gerno di Lesmo (MB),

Italy

Tel: +39-039-9065-1

SPAIN/PORTUGAL

Yamaha Music Europe GmbH Ibérica, Sucursal

en España

Ctra. de la Coruña km. 17,200, 28231

Las Rozas de Madrid, Spain

Tel: +34-91-639-88-88

GREECE

Philippos Nakas S.A. The Music House

19th klm. Leof. Lavriou 190 02 Peania – Attiki,

Greece

Tel: +30-210-6686260

SWEDEN

Yamaha Music Europe GmbH Germany filial

Scandinavia

JA Wettergrensgata 1, 400 43 Göteborg, Sweden

Tel: +46-31-89-34-00

DENMARK

Yamaha Music Denmark,

Fillial of Yamaha Music Europe GmbH, Tyskland

Generatorvej 8C, ST. TH., 2860 Søborg, Denmark

Tel: +45-44-92-49-00

FINLAND

F-Musiikki Oy

Antaksentie 4

FI-01510 Vantaa, Finland

Tel: +358 (0)96185111

NORWAY

Yamaha Music Europe GmbH Germany -

Norwegian Branch

Grini Næringspark 1, 1332 Østerås, Norway

Tel: +47-6716-7800

ICELAND

Hljodfaerahusid Ehf.

Sidumula 20

IS-108 Reykjavik, Iceland

Tel: +354-525-5050

CYPRUS

Nakas Music Cyprus Ltd.

Nikis Ave 2k

1086 Nicosia

Tel: + 357-22-511080

Major Music Center

21 Ali Riza Ave. Ortakoy

P.O.Box 475 Lefkoşa, Cyprus

Tel: (392) 227 9213

RUSSIA

Yamaha Music (Russia) LLC.

Room 37, entrance 7, bld. 7, Kievskaya street,

Moscow, 121059, Russia

Tel: +7-495-626-5005

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

Yamaha Music Gulf FZE

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

TURKEY

Yamaha Music Europe GmbH

Merkezi Almanya Türkiye İstanbul Şubesi

Maslak Meydan Sodak, Spring Giz Plaza Bagimsiz

Böl. No:3, Sariyer Istanbul, Turkey

Tel: +90-212-999-8010

ISRAEL

RBX International Co., Ltd.

P.O Box 10245, Petach-Tikva, 49002

Tel: (972) 3-925-6900

OTHER COUNTRIES

Yamaha Music Gulf FZE

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co., Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: +86-400-051-7700

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: +852-2737-7688

INDIA

Yamaha Music India Private Limited

P-401, JMD Megapolis, Sector-48, Sohna Road,

Gurgaon-122018, Haryana, India

Tel: +91-124-485-3300

INDONESIA

PT. Yamaha Musik Indonesia (Distributor)

Yamaha Music Center Bldg. Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: +62-21-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, Dongsung Bldg. 21, Teheran-ro 87-gil,

Gangnam-gu, Seoul, 06169, Korea

Tel: +82-2-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn. Bhd.

No.8, Jalan Perbandaran, Kelana Jaya, 47301

Petaling Jaya, Selangor, Malaysia

Tel: +60-3-78030900

SINGAPORE

Yamaha Music (Asia) Private Limited

Block 202 Hougang Street 21, #02-00,

Singapore 530202, Singapore

Tel: +65-6740-9200

TAIWAN

Yamaha Music & Electronics Taiwan Co., Ltd.

2F., No.1, Yuandong Rd., Banqiao Dist.,

New Taipei City 22063, Taiwan (R.O.C.)

Tel: +886-2-7741-8888

THAILAND

Siam Music Yamaha Co., Ltd.

3, 4, 15, 16th Fl., Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: +66-2215-2622

VIETNAM

Yamaha Music Vietnam Company Limited

15th Floor, Nam A Bank Tower, 201-203 Cach

Mang Thang Tam St., Ward 4, Dist.3,

Ho Chi Minh City, Vietnam

Tel: +84-28-3818-1122

OTHER ASIAN COUNTRIES

http://asia.yamaha.com

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 80 Market Street, South Melbourne,

VIC 3205 Australia

Tel: +61-3-9693-5111

NEW ZEALAND

Music Works LTD

P.O.BOX 6246 Wellesley, Auckland 4680,

New Zealand

Tel: +64-9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

http://asia.yamaha.com

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

DMI23

Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan

(For European Countries) Importer: Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany

For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.

ZZ14030

Manual Development Group

Published 12/2017 POES*.*-**A0

Printed in China

Yamaha Global Site

https://www.yamaha.com/

Yamaha Downloads

https://download.yamaha.com/

Yamaha PSR-E463 El manual del propietario

Marca: Yamaha

Modelo: PSR-E463

Categoría: Instrumentos musicales

Tipo: El manual del propietario

Este manual también es adecuado para

PSR-EW410

Descargar PDF

informe

en otros idiomas

français: Yamaha PSR-E463 Le manuel du propriétaire
italiano: Yamaha PSR-E463 Manuale del proprietario
English: Yamaha PSR-E463 Owner's manual
Deutsch: Yamaha PSR-E463 Bedienungsanleitung
русский: Yamaha PSR-E463 Инструкция по применению
Nederlands: Yamaha PSR-E463 de handleiding
português: Yamaha PSR-E463 Manual do proprietário
dansk: Yamaha PSR-E463 Brugervejledning
polski: Yamaha PSR-E463 Instrukcja obsługi
čeština: Yamaha PSR-E463 Návod k obsluze
svenska: Yamaha PSR-E463 Bruksanvisning
日本語: Yamaha PSR-E463 取扱説明書
Türkçe: Yamaha PSR-E463 El kitabı
suomi: Yamaha PSR-E463 Omistajan opas
română: Yamaha PSR-E463 Manualul proprietarului

Yamaha PSR-E463 El manual del propietario

Este manual también es adecuado para

Yamaha PSR-E463 El manual del propietario

en otros idiomas

Artículos relacionados