Item # 317994709/ 317994705

Model # 564291010/ 564291020

HARDWARE INCLUDED

Part Description Quantity

AA Mounting Bracket 1

BB Mounting Screw (for

Bracket) 2

CC Wire Connector 3

USE AND CARE GUIDE

drilling, based on the type of ceiling.

1. Pass the hot and neutral (black and white) wires from the electrical outlet box through the middle hole of the mounting

bracket (AA).

Align the mounting bracket (AA) using the mounting screws (BB) and tighten securely to the electrical box.

2. Connect the hot and neutral (black and white) wires from the J-box to the same color wires from the fixture body (A).

Connect the grounding wire from the J-box to the green wire from fixture base (A). Cover the wire connections using the

wire connectors (CC). Make sure to fasten them well.

3. Cover the wire connectors (CC) with electrical tape for a more secure connection.

4. Position the wires back inside the electrical box.

5. Align the side slots on the fixture body (A) with the mounting bracket (AA) and fix the fixture body (A) securely by carefully

STEP 1. STEP 2. STEP 3.

Minor problems often can be fixed without the help of an electrician.

WARNING: Before doing any work on the fixture, disconnect power to the light fixture.

WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation.

the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. • To reduce the possibility of serious

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving

date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If

this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the

product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications,

alterations, neglect, or mishandling.

WHAT IS NOT COVERED

This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in anyway not in accordance

with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse,

apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.

The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose,

There is a bad connection. Check to ensure proper wire connections are made.

Contact a qualified electrician.

There is a defective switch. Contact a qualified electrician.

The fuse blows or the circuit

breaker trips when the light is

turned on.

The wires are crossed or the power

Contact a qualified electrician or call Hampton Bay

customer service 1-855-HD-HAMPTON.

inserting into bracket or ceiling.

NOTE: The factory setting for the correlated color

temperature (CCT) is 2700K.

9IN. COLOR SELECTABILITY FLUSHMOUNT

Artículo # 317994709/ 317994705

Modelo # 564291010/ 564291020

MATERIALES INCLUIDOS

Pieza Descripción Cantidad

AA Soporte de montaje 1

(por caja eléctrica) 2

nuevo.

Si no está familiarizado con las instalaciones eléctricas, le recomendamos que haga que un electricista calificado se ocupe de la

INSTALACIÓN

Seleccione una ubicación adecuada que pueda soportar el peso de la lámpara. Determine el método de montaje de la lámpara

antes de la perforación, en función del tipo de techo.

1. Pase los cables vivo y neutro (negro y blanco) desde la caja eléctrica a través del orificio central del soporte de

montaje (AA).

Alinee el soporte de montaje (AA) con los tornillos de montaje (BB) y apriete firmemente a la caja eléctrica.

2. Conecte los cables vivo y neutro (negro y blanco) de la caja de conexiones a los cables del mismo color del cuerpo de la

6. Restablece la energía en el panel eléctrico. Encienda el interruptor de luz para activar la lámpara.

Pieza Descripción Cantidad

A Cuerpo de lámpara 1 A

PASO 1. PASO 2. PASO 3.