Yamaha mLAN16E Guía de instalación

Categoría
Teclados
Tipo
Guía de instalación

Este manual también es adecuado para

1
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN,
Plug-in Effect Installation Guide/Installationshandbuch/Manuel d’installation
SPECIAL NOTICES
Some of the included CD-ROMs may be copy-protected. Yamaha makes no representations or
warranties with regard to any problems while attempting to copy the CD-ROM(s) or software and
cannot be held responsible for the results of attempts to copy the data.
The software and this Installation Guide are exclusive copyrights of Yamaha Corporation.
Use of the software and this guide is governed by the SOFTWARE LICENSING AGREEMENT
which the purchaser fully agrees to upon breaking the seal of the software packaging. (Please read
carefully the AGREEMENT at the end of this guide before installing the application.)
Copying of the software or reproduction of this guide in whole or in part by any means is expressly
forbidden without the written consent of the manufacturer.
•Yamaha makes no representations or warranties with regard to the use of the software and
documentation and cannot be held responsible for the results of the use of this guide and the
software.
Copying of the commercially available music data is strictly prohibited except for your personal use.
The company names and product names in this Installation Guide are the trademarks or registered
trademarks of their respective companies.
Software such as the mLAN driver may be revised and updated without prior notice. Make sure to
check and download the latest version of the software from the following site.
http://www.yamahasynth.com/down/index.htm
Future upgrades of application and system software and any changes in specifications and functions
will be announced separately.
BESONDERE HINWEISE
Einige der mitgelieferten CD-ROMs sind möglicherweise kopiergeschützt. Yamaha gibt bei
Problemen im Zusammenhang mit dem Versuch, die CD-ROM oder die Software zu kopieren, keine
Zusicherungen oder Gewährleistungen und kann für die Folgen des Kopierens der CD-ROM oder
der Software nicht verantwortlich gemacht werden.
Dieses Programm und diese Installationsanleitung sind im Sinne des Urheberrechts alleiniges
Eigentum der Yamaha Corporation.
Die Benutzung des Programms und dieser Anleitung unterliegt der SOFTWARE-
LIZENZVEREINBARUNG, mit der sich der Erwerber durch Öffnen des Siegels der
Programmverpackung uneingeschränkt einverstanden erklärt. (Bitte lesen Sie die
VEREINBARUNG am Ende dieser Anleitung vor Installation der Anwendung sorgfältig durch.)
Installation Guide/Installationshandbuch/Manuel d’installation
EnglishDeutschFrançais
2
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN,
Plug-in Effect Installation Guide/Installationshandbuch/Manuel d’installation
Das Kopieren der Software und die Reproduktion dieser Anleitung, in welcher Form auch immer, in
Teilen oder als Ganzes, sind nur mit schriftlicher Genehmigung des Herstellers erlaubt und sonst
ausdrücklich verboten.
•Yamaha leistet keinerlei Garantie hinsichtlich der Benutzung des Programms und der zugehörigen
Dokumentation und übernimmt keine Verantwortung für die Ergebnisse der Benutzung dieser
Anleitung oder des Programms.
Das Kopieren im Handel erhältlicher Musikdaten ist nur für Ihren Privatgebrauch zulässig und sonst
streng untersagt.
Die in dieser Installationsanleitung erwähnten Firmen- und Produktnamen sind Warenzeichen bzw.
eingetragene Warenzeichen der betreffenden Firmen.
Software wie z.B. der mLAN Driver kann ohne vorherige Benachrichtigung überarbeitet und
aktualisiert werden. Achten Sie darauf, auf der folgenden Website nach der neuesten Version der
Software zu suchen und sie herunterzuladen.
http://www.yamahasynth.com/down/index.htm
Zukünftige Aktualisierungen von Anwendungs- und Systemsoftware sowie jede Änderung der
technischen Daten und Funktionen werden separat bekanntgegeben.
REMARQUES PARTICULIERES
Certains des CD-ROM inclus peuvent être protégés contre la copie. Yamaha n’offre aucune garantie
quant aux problèmes pouvant surgir lors de la copie du CD-ROM ou du logiciel et ne peut être tenu
responsable du résultat de la copie du CD-ROM ou du logiciel.
Les droits d’auteurs (copyright) de ce logiciel et de ce manuel d’installation appartiennent
exclusivement à Yamaha Corporation.
•L’usage de ce logiciel et de ce manuel est défini par l’accord de licence auquel l’acheteur déclare
souscrire sans réserve lorsqu’il ouvre le sceau de l’emballage du logiciel. (Veuillez donc lire
attentivement l’accord de licence du logiciel situé à la fin de ce manuel avant d’installer le logiciel.)
•Toute copie du logiciel et toute reproduction totale ou partielle de ce manuel, par quel moyen que ce
soit, est expressément interdite sans l’autorisation écrite du fabricant.
•Yamaha n’offre aucune garantie en ce qui concerne l’utilisation du logiciel et de la documentation.
Yamaha ne peut en aucun cas être tenu responsable des dommages éventuels résultant de
l’utilisation de ce manuel et de ce logiciel.
•Toute copie de données musicales commercialisées est formellement interdite, sauf pour usage
personnel.
Les noms des firmes et des produits apparaissant dans ce manuel d’installation sont des marques
commerciales ou des marques déposées appartenant à leurs détenteurs respectifs.
Les logiciels tels que le pilote mLAN sont susceptibles d’être révisés et mis à jour sans
avertissement préalable. Veuillez toujours à vérifier la version du logiciel utilisée et à télécharger la
dernière version en date sur le site suivant :
http://www.yamahasynth.com/down/index.htm
Les remises à jour du programme et du système ainsi que toute modification des caractéristiques et
fonctions seront annoncées séparément.
EnglishDeutschFrançais
3
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Contents
Important Notices about the CD-ROM.............................................4
Operating System (OS) ..........................................................................4
CD-ROM Installation Procedure .............................................................4
For Windows Users...........................................................................5
CD-ROM Contents..................................................................................5
System Requirements for i88X/mLAN16E/MY16-mLAN Software.........6
Software Installation ...............................................................................8
Connecting a Computer to an mLAN device via mLAN........................19
Installing the Plug-in Effect (For i88X Users)........................................26
For Mac OS 9 Users (i88X and mLAN16E only)............................28
CD-ROM Contents................................................................................28
System Requirements for i88X/mLAN16E Software ............................30
Software Installation .............................................................................31
Connecting a Computer to an mLAN device via mLAN........................36
Plug-in Effect ........................................................................................41
For Mac OS X Users........................................................................42
Display Messages ...........................................................................43
Troubleshooting..............................................................................44
Noise may be generated during the following operations. Before performing these operations, lower the output level of
each device.
Turning the power to the computer and mLAN devices on or off
Connecting or disconnecting an IEEE1394 (mLAN) cable
Making an mLAN connection in mLAN Auto Connector
Changing the wordclock master and slave status in mLAN Auto Connector or mLAN Graphic Patchbay
Selecting On or Off in mLAN Manager (Windows)
Starting or quitting the OS
Installing/uninstalling mLAN software
For Windows users
Do not turn on the power to the mLAN
devices during installation until the
computer displays the following
message.
4
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Operating System (OS)
The data content and installation procedure is different for Windows and Macintosh. Please read the
section that applies to your operating system.
i88X/mLAN16E users:
The CD-ROM contains software for Windows
and Mac OS 9.
Windows please read from page 5.
Mac OS 9 please read from page 28.
MY16-mLAN users:
The CD-ROM contains software for Windows.
Software for Macintosh is not included.
Windows please read from page 5.
Regarding Mac OS X support, refer to page 42.
CD-ROM Installation Procedure
Before breaking the seal on the software packaging, please read carefully the Software Licensing
Agreement at the end of this guide.
1 Verify that your system meets the operating
requirements of the software (mLAN Tools,
driver, etc.).
Windows: page 6; Mac OS 9: page 30
2 Install the appropriate driver on your com-
puter, and make the necessary settings.
Windows: page 9; Mac OS 9: page 31
3 i88X Users: Install the Plug-in Effect.
Windows: page 5; Mac OS 9: page 28
4 Start up the software.
For subsequent operations, refer to the owner’s
manual for each software program (online help/
PDF manual).
To view PDF files, you must install Adobe Reader on
your computer. If you do not have Adobe Reader, you
can download the application from the Adobe website
at the following URL:
http://www.adobe.com
Quick solutions/Reference materials
• Setting the sampling frequency ........................................................................... page 19, 36
• Determining the number of mLAN audio channels. ............................................. page 19, 36
• Changing the settings of the mLAN Driver........................................................... page 15, 34
• Determining the latency ............................................................................................. page 15
• How can I delete or re-install the driver?........................................................ pages 8, 25, 33
• Connecting multiple mLAN devices..................................................................... page 19, 36
Important Notices about the CD-ROM
Most of the computer display examples in this
guide are taken from the English version OS/
software.
5
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
CD-ROM Contents
Software for Windows is included on CD-ROM(s). (i88X users should begin by installing TOOLS for
i88X/mLAN16E.)
TOOLS for i88X/mLAN16E
TOOLS for MY16-mLAN
Plug-in Effect (included only with i88X)
This software can be used as plug-in software within a VST compatible program.
•To call up the PDF manual for each program, select [Start] [All programs] [YAMAHA VST
Plugins] (the relevant software) [Online Manual].
•For instructions on installing the Plug-in Effects, see page 26.
*1 These applications are supplied with online/PDF manuals.
For Windows Users
Folder Name Application Name Contents
mLAN_
mLAN Applications
for YAMAHA
mLAN Tools
This software includes mLAN drivers and applications required to make
mLAN connections between the mLAN devices and the computer.
Install the software while the power to the mLAN devices is off (page
9). A single installation procedure installs all applications necessary for
mLAN communications. Software to be installed includes mLAN Auto
Connector and mLAN Graphic Patchbay, which are used to set up
audio and MIDI connections for an mLAN network.
Folder Name Application Name Contents
VST_
01X Channel
Module
*1
This software reproduces the EQ and Dynamics effects built into each
channel of the YAMAHA Digital Mixing Studio 01X, and uses the
processing power of the computer for the effects.
You can use the Dynamics and 4-band EQ functions (that can be also
found on Yamaha Digital Mixing consoles) as effects software. You can
also import the 01X settings, thus reproducing the songs created on
the 01X.
Pitch Fix
*1
This program is used to edit the pitch of recorded vocals. More than
just a pitch processor, it can also be used to change the character of
the vocals. Moreover, you can use MIDI data on the host application to
control the Pitch Fix effect. For more information on setting up with the
host application, refer to the Pitch Fix PDF owner’s manual.
Vocal Rack
*1
This is a multi-effect program for processing vocals. The plug-in
features various effects, including a high-pass filter, compressor and a
3-band equalizer.
Final Master
*1
This is a multi-effect program for mastering purposes. It features a
compressor, limiter and soft-clip function, and allows you to split the
signal into three bands for separate multi-band processing.
6
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
About Open Plug-in Technology
You can start mLAN Graphic Patchbay as either stand-alone software or as a plug-in for an Open Plug-
in Technology compatible application.
Open Plug-in Technology (OPT) is a new software format that enables you to control MIDI devices from a
music software sequencer. For example, OPT enables you to start and operate various parts of your music
system, such as Plug-in Board editors and mixing control editors, directly from an OPT-compatible
sequencer. OPT also makes it unnecessary to set MIDI drivers for each application, streamlining your
music production system and making all operations more convenient and seamless.
About OPT Levels
The client application and its compatibility with OPT can be divided into three levels, as shown below.
OPT Level Implementation for the mLAN Graphic Patchbay
This chart shows the OPT-compatibility of mLAN Graphic Patchbay.
All mLAN Graphic Patchbay functions work under the client applications of any OPT level (Panels
(Level 1), Processors (Level 2), and Views (Level 3)).
Certain operations may not work as expected if there is no corresponding function in the client application (sequencer,
etc.). The highest level of implementation for the client application is indicated in the OPT logo (which appears along with
the version information in the application).
System Requirements for i88X/mLAN16E/MY16-mLAN
Software
The system requirements below are necessary for using the included software.
The system requirements below may differ slightly depending on the particular operating system.
The minimum requirements for included software not listed below may differ. For details, refer to the relevant online
manual or documentation of the software.
For details on minimum requirements for each DAW (Digital Audio Workstation) software, refer to the respective owner’s
manual.
Level 1 (OPT Panels) provides basic support for opening and displaying OPT control panels that can transmit
data via a clients’ external MIDI connectors.
Typically, this enables basic hardware editor control panels to operate properly.
Level 2 (OPT Processors) provides support for real-time MIDI processors and panel automation. Typically, this
enables both real-time and offline MIDI effects (e.g., arpeggiators, transposers, etc.) to operate properly and
supply automation to OPT panels.
Level 3 (OPT Views) provides support for edit views and MIDI processors and panels that require direct access to
client sequencer storage structures.
Typically, this enables support of sophisticated MIDI edit views (e.g., list editors, auto accompaniment, data
checkers, etc.).
OPT levels of the client application
mLAN Graphic Patchbay operation
Operation support Operation limits
VIEWS (Level 3) Yes None
PROCESSORS (Level 2) Yes None
PANELS (Level 1) Yes (with limitations) None
7
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
i88X/mLAN16E/MY16-mLAN
(mLAN Tools 2.0/mLAN Applications for
YAMAHA)
These are the total system requirements,
including the audio sequencer, mLAN
software and the plug-in effects.
OS : Windows XP Professional/XP Home
Edition
Computer : Intel Pentium or Celeron family pro-
cessor, with the S400 (400 Mbps)
IEEE1394 (FireWire) or i.Link termi-
nal (*1).
Hard Disk : Free disk space of 250 MB (i88X)/
50 MB (mLAN16E, MY16-mLAN) or
more; high-speed hard disk
Recommended system (*2)
Connecting a single mLAN device to a com-
puter peer-to-peer:
Computer : 2.2 GHz or higher;
Intel Pentium 4 pro-
cessor
Available Memory : 512 MB or more
Connecting a computer and three mLAN
devices in an mLAN network:
Computer : 2.6 GHz or higher;
Intel Pentium 4 pro-
cessor
Available Memory : 512 MB or more
Minimum system requirements (*2)
Computer : Intel Pentium 1.2 GHz
or Intel Celeron 1.7
GHz (or higher)
Available Memory : 384 MB or more
*1 The computer must have an IEEE 1394
(FireWire) or i.Link terminal. If there is no ter-
minal, install an IEEE 1394 interface card
(PCI or PC).
For more details on system requirements and
recommended PCI or PC cards, see
http://www.yamahasynth.com
*2 The system requirements listed here apply
when using the included software and when
playing audio/MIDI data detailed below on
standard sequencer software. This may differ
depending the particular sequencer software
you are using.
Recommended system requirements (Connecting
a single mLAN device to a computer peer-to-peer)
Fs=44.1kHz/24-bit
Audio Driver
18In/18Out (i88X)
16In/8Out (mLAN16E)
16In/16Out (MY16-mLAN)
MIDI Driver
1In/1Out (i88X, MY16-mLAN)
3In/3Out (mLAN16E)
16 MIDI and 12 Audio playback tracks
2 Audio recording tracks
2 Sends for Plug-in Soft Effect
10 Inserts for Plug-in Soft Effect
2 Channels for Plug-in Soft Synthesizer
Latency of 5msec or less
Recommended system requirements (Connecting
a computer and three mLAN devices)
Fs=44.1kHz/24-bit
Audio Driver 32In/32Out (total)
MIDI Driver 4In/5Out (total)
16 MIDI and 8 Audio playback tracks
2 Audio recording tracks
2 Sends for Plug-in Soft Effect
10 Inserts for Plug-in Soft Effect
2 Channels for Plug-in Soft Synthesizer
Latency of 5msec or less
Minimum system requirements
Fs=44.1kHz/16bit
Audio Driver
8In/2Out (i88X)
2In/2Out (mLAN16E, MY16-mLAN)
MIDI Driver
1In/1Out (i88X, MY16-mLAN)
2In/2Out (mLAN16E)
16 MIDI and 12 Audio playback tracks
2 Sends for Plug-in Soft Effect
6 Inserts for Plug-in Soft Effect
No Plug-in Soft Synthesizer
Latency of about 50msec
Up to two PCI or PC cards can be used. However,
you can use only one card at a time.
If you are using an IEEE1394 interface built into the
computer, you can use only one IEEE1394 PCI or
PC interface card.
When using a laptop or notebook computer, a built-
in IEEE 1394 terminal may not be available. If this is
the case, install an appropriate PC interface card.
Plug-in Effect (included only with i88X)
OS : Windows XP Professional/XP Home Edition/2000/Me/n98SE/98
To use mLAN, turn mLAN on each time you start the computer by using the mLAN icon (mLAN Man-
ager) in the task bar (page 14).
8
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Software Installation
For instructions on how to install the software other than one referred to below, see page 5 in the sec-
tion “CD-ROM Contents.”
Uninstall (removing the installed application)
You can remove the installed application software.Select [START] ( [Settings]) [Control Panel]
[Add/Remove Programs] [Install/Uninstall], then select the application to be removed and click [Add/
Remove...]. Follow the on-screen instructions to uninstall the application.
The button names or menus may differ depending on the computer OS.
In order to uninstall the mLAN software, the following two items must be deleted. Delete them in order, 1 then 2.
1. mLAN Applications for YAMAHA
2. mLAN Tools 2.0
For information on uninstalling the plug-in effect, see page 27.
Check beforehand the drive name (D:, E:, etc.) corresponding to the CD-ROM you are using. The drive
name is indicated under the CD-ROM icon of [My computer]. (The root directory of the CD-ROM driver
is indicated as D:\, E:\, etc.)
9
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
mLAN Tools 2.0 and mLAN Applications for YAMAHA
mLAN Tools 2.0 software includes a driver that enables you to connect mLAN devices to a computer.
mLAN Applications for YAMAHA enables audio and MIDI signals to be transferred between a
computer and mLAN devices via mLAN cables.
This software enables you to connect the i88X, mLAN16E, MY16-mLAN, or 01X to a computer via
mLAN. 01X users should uninstall the older version of the mLAN software before installing this
software. (Refer to the 01X Installation Guide.)
Follow the steps below to install these software applications.
For explanations on error messages, see page 43.
Preparing to install
1 Disconnect all MIDI cables that connect MIDI
devices to MIDI IN/OUT connectors on the
mLAN device.
2 Using an IEEE1394 (FireWire/iLink) cable,
connect the mLAN device directly to the com-
puter (without using a hub), and disconnect all
other IEEE 1394-connected devices from the
computer.
3 Make sure that the power to the mLAN device
is turned off.
4 Start the computer and log in to the Adminis-
trator account.
If you are using the S200 data transfer rate stan-
dard (check the rear panel of your particular
device, or refer to the specifications in the owner’s
manual), make sure to uninstall the old version of
mLAN Tools beforehand. For more information on
uninstalling the software, refer to the owner’s
manual for the corresponding device.
5 Select [Start] [Control Panel]. If the control
panel appears as shown below, click “Switch
to Classic View” in the upper left of the win-
dow.All control panels and icons will be dis-
played.
Proceed to the next step.
10
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
6 Go to [System] [Hardware] [Driver Signing] [File Signature Verification], and check the radio
button to the left of “Ignore -Install all files, regardless of file signature” and click [OK].
After completing the installation, make sure to restore the original setting if necessary.
7 Check that no “!” or “x” marks appear next to “IEEE 1394 Bus host controllers” (in [System] [Hard-
ware] [Device Manager]). If one of these marks is shown, the mLAN (IEEE 1394/i.Link) connection
cannot be used. Refer to the owner’s manual of your computer for details.
11
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
8 Click [OK] to close the System Properties win-
dow, then click the Close button ([X]) at the
top right of the window to close the Control
Panel.
9 Exit from any open applications and close all
open windows.
10 Insert the included CD-ROM into the CD-
ROM drive.
Starting up the Installer for the
mLAN Software
The installer will install the following two
programs to your computer.
mLAN Tools 2.0
mLAN Application for YAMAHA
Use the Cancel button or Close button to quit the
installation. Quitting by using the [CTR]+[ALT]+[DEL]
buttons or by turning off the power while installation is
in process is can result in problems since the installa-
tion is terminated without performing a proper uninstall.
11 Double-click on the “mLAN_” folder.
Various files are shown, including
“Setup.exe.”
12 Double-click on “Setup.exe.”
13 A series of confirmation messages appear.
If there are no problems, click [OK] in each
message. When finished, a “Welcome” dis-
play appears.
Installation of mLAN Tools
14 Click [Next]. The display for installing mLAN
Tools appears.
15 Click [Next]. The “Destination Directory”
window appears, letting you determine the
desired drive and folder name for installing
mLAN Tools. The destination directory is
automatically set; however, if you wish to
change it, click the [Browse…] button and
select the desired folder (drive:\folder
name). Click [Next] after making or confirm-
ing the selection.
In general, there is no need to change the desti-
nation directory.
16 Confirm the drive and folder name and click
[Next] to start installation.
To cancel the installation, click [Cancel].
17 When installation is finished, a “Completed”
message appears. Click [Finish].
Proceed to the next step.
12
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Installation of mLAN Applications
for YAMAHA (mLAN Software)
When the mLAN Tools 2.0 installation is
complete, the computer automatically
displays a window that enables you to start
the installation of Applications for YAMAHA.
Click [Next].
18 Determine the desired destination drive and
folder name for installation in the “Destina-
tion Directory” window. The destination
directory is automatically set; however, if
you wish to change it, click the [Browse…]
button and select the desired folder
(drive:\folder name).
To cancel the installation, click [Cancel].
19 Confirm the drive and folder name and click
[Next] to start installation.
To cancel the installation, click [Cancel].
20 When the installation process is complete,
a message will prompt you to restart the
computer. Click [Next].
mLAN Driver initial settings
After you restart the computer, complete the
mLAN driver initial settings. Select [ON] in
mLAN Manager to activate the mLAN driver
(page 14).
21 A dialog box prompts you to turn on the
power to the mLAN device. Connect the
mLAN device to the computer, then turn on
the power to the i88X, mLAN16E, or MY16-
mLAN (or 01X).
22 Installing the mLAN device
The “Found New Hardware Wizard” window
is displayed.
Check the radio button next to “Install the
software automatically [Recommended],”
then click [Next].
Depending on the version of Windows you are
using, the “Found New Hardware Wizard” may
display a screen asking you whether you want
to find the appropriate software by connecting
to Windows Update. In this screen, choose the
radio button next to the selection indicating that
you don’t want to connect to Windows Update,
and then click [Next].
Even if such a screen should appear subse-
quently in this procedure, choose the radio but-
ton indicating that you don’t want to connect,
and then click [Next].
23 After you finish installing the connected
mLAN device, click [OK] in the dialog box
that appeared in Step
21.
When canceling the installation
If you’ve cancelled an installation before it is
complete, the software may not have been
installed properly. Follow the instructions
below to properly install the software.
1 Click on “Add or Remove Programs” in the
Control Panel (page 8) and find “mLAN
Applications for YAMAHA” and “mLAN
Tools 2.0” in the list.
2 Delete the two programs in order: first,
“mLAN Applications for YAMAHA,” then
“mLAN Tools 2.0.”
3 Start installation again from step 12 (page
11).
13
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
24 The “Make the driver initial settings” dialog
box is displayed. Click [OK].
During Steps 25 and 26, and Steps 28 and 29,
the computer displays a window indicating that
you are now making the initial settings for each
driver. This window also indicates the number of
times the “Found New Hardware Wizard” will be
displayed during the procedure. Unless you wish
to cancel installation, do not close this window.
Example:
mLAN Network initial settings
25 The computer automatically displays the
“Found New Hardware Wizard.” Check the
radio button next to “Install the software
automatically [Recommended],” then click
[Next].
26 When the installation is complete, the com-
puter displays a message indicating that
installation is complete. Click [Finish].
27 Repeat Steps 25 and 26 until the window
(indicating that you are making the mLAN
Bus driver initial settings) closes.
mLAN MIDI Port initial settings
28 The computer automatically displays the
“Found New Hardware Wizard.” Check the
radio button next to “Install the software
automatically [Recommended],” then click
[Next].
29 When the installation is complete, the com-
puter displays a message of indicating that
installation is complete. Click [Finish].
30 Repeat Steps 28 and 29 until the window
(indicating that you are making the mLAN
Stream driver initial settings) closes.
31 The computer displays a message indicat-
ing that the initial settings for mLAN driver
are complete. Click [OK].
To use an audio sequencer via mLAN, you
must connect the computer to the mLAN
device using mLAN audio Connector or
Graphic Patchbay (page 19).
14
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Confirming the installation
Task bar (mLAN Manager)
If the installation is successful, an mLAN icon
(mLAN Manager) is added to the task bar. To
call up the menu, right-click on the icon.
ON.................... Enables mLAN operation for
data transfer (Run the “mLAN
Start application”).
OFF.................. Disables mLAN operation
(Run the “mLAN Stop”
application). You can lessen the
CPU load by not using mLAN.
Driver Setup ... Starts mLAN Driver Setup
(page 15).
Auto Connector ....... Starts mLAN Auto
Connector (page 19).
Graphic Patchbay ... Starts mLAN Graphic
Patchbay. For more
information, refer to the
mLAN Graphic Patchbay
Online Manual.
EXIT................ This deletes the mLAN icon
from the task bar, maintaining
the current mLAN ON/OFF
status. To display it again,
select [Start] [(All)
Programs] [Startup]
[mLAN Manager].
To use mLAN connections, after you start the com-
puter, right-click the mLAN icon (mLAN Manager) in
the Task bar, then select [ON] to activate mLAN con-
nections.
You can use the mLAN Driver Setup (page 15) to
check whether data is being properly transmitted and
received via mLAN.
When starting up the mLAN
The message below appears when mLAN is
being started.
To cancel mLAN startup, click [Cancel] in the
mLAN Start window. To use mLAN, right-click
on the mLAN icon (mLAN Manager) in the task
bar, and select [ON].
Device Manager (Operating System)
1 Select [Control Panel] from the Start menu.
2 Double-click on the System icon to call up the
System Properties window.
3 Select the Hardware tab and click [Device
Manager].
4 Click the [+] symbol located at the left of
“Sound, video and game controllers,” and ver-
ify that “YAMAHA i88X,” “YAMAHA
mLAN16E,” or “YAMAHA MY16-mLAN” etc. is
shown. Also verify that “YAMAHA mLanBus”
is shown.
When using mLAN, right click on the mLAN
icon (mLAN Manager) in the task bar and
select “ON” (start mLAN).
15
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Changing settings after installation
The mLAN-related settings can be changed after installation from the mLAN Driver Setup window.
mLAN Driver Setup
(Right-click the mLAN icon in the task bar DriverSetup)
This window lets you check and change the mLAN settings for receiving/transmitting data. Make sure
to close any application (DAW, etc.) using the mLAN connection before making changes.
To change the wordclock (sample rate) and the number of channels used, right-click on the mLAN icon in the task bar
and start the mLAN Auto Connector and Graphic Patchbay.
q 1394 Adapter Card ID
This indicates the particular ID of the IEEE 1394 (FireWire/iLink) interface card installed to the
computer. When several cards are installed, this is used to select the desired card. Cards not recognized
by the mLAN driver are not displayed.
The correct name of the manufacturer or vendor may not be displayed depending on the particular card you are using.
w Required CPU
Determines the computer’s required processing power (the amount of processing load applied to the
computer by the mLAN driver).
You can also control the processing load by adjusting the latency in “ASIO mLAN Control Panel.
(see below)
q
w
e
t r
y
Latency and Required CPU
A particular computer configuration (i.e., processing speed and system memory size) may affect the
computer’s ability to properly record and play back audio data in your audio sequencer, resulting in
noise or other audio problems.
In most cases, you can solve these problems by adjusting the latency (delay time). (See “Latency of
mLAN” on page 16.)
16
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect
Installation Guide
English
However depending on the performance of your computer and on how it is being used (i.e., whether other
applications are being used simultaneously, or whether multiple mLAN devices are connected, etc.), you
may still experience noise or sound interruption even after increasing the latency. In this case, change the
“Required CPU” setting to “Medium Performance” or “Low Performance” to lighten the processing load on
your computer, and then adjust the latency (the Preferred Buffer Size setting below) once again.
•Lower latency values result in shorter delay times and work better for real-time recording and
playback.
Higher latency values result in longer delay times, but allow for use of more audio channels and
plug-in effects (thus reducing the computer’s momentary processing load).
Conversely, if you experience no noise or interruptions even with the “Preferred Buffer Size” setting
described below set to the minimum, you can minimize the overall latency by setting Required CPU to
“High Performance” and then adjusting the latency once again.
Latency of mLAN
Audio latency (msec)
Audio latency is determined by the “Preferred Buffer Size” setting in the “ASIO mLAN Control Panel.”
The audio latency value is shown in the “ASIO mLAN Control Panel” (see below).
MIDI latency (msec)
The MIDI latency value varies with the mLAN driver version.
For information on the MIDI latency of your mLAN driver version, refer to the “MIDI_Latency.txt” file,
which you can access by selecting [Program files | mLAN Tools | YAMAHA].
ASIO mLAN Control Panel
When you start the ASIO mLAN Control Panel, the system displays the following dialog box.
When using the mLAN ASIO Driver, open the ASIO Control Panel within the driver settings of the DAW
software (the particular menu depends on the software you are using) and set the Preferred Buffer Size
as needed.
Also, when using the mLAN WDM driver, adjust as necessary the latency value of the WDM driver (which corre-
sponds to the latency of the ASIO driver in this chart) within the driver settings of the DAW software.
The initial setting of the Preferred Buffer Size of the mLAN ASIO driver is the smallest value.
q
Preferred Buffer Size
This parameter enables you to
specify the size of the buffer inside
the mLAN ASIO driver.
w
Sample Size
This parameter enables you to
specify the bit resolution for audio
data transmission and reception.
e
Latency
This field indicates the audio latency
value for transmission and reception.
Audio latency is determined by the
“Preferred Buffer Size (
w
)” setting.
r
OK
Click to enable the settings and close the dialog box.
t
Cancel
Click to close the dialog box without changing the settings.
q
t
w
e
r
#mLAN InstallGuide_E2.fm Page 16 Monday, October 4, 2004 11:53 AM
17
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
e Status
If you are using mLAN Auto Connector, this
parameter indicates the current data (MIDI/
Audio) reception status (from the mLAN device
to computer) of the mLAN connection. If there
is an error in transmission, the computer
displays an error message.
If you are using mLAN Graphic Patchbay, refer
to the Graphic Patchbay Online Manual for
information on the error messages.
Blue ....... Data is being properly transmitted.
Yellow ... Only one type of data (MIDI or
audio) is being received.
Red ........ Error in reception.
Gray....... No reception.
r Set
Clicking this button actually applies the settings
made in this window. Changes to the settings do
not take effect unless [Set] is clicked.
t Revert
If you’ve made changes to the settings (but not
yet clicked [Set]), clicking this button restores
the settings made the last time [Set] was clicked.
Once you click [Set], [Revert] cannot be used.
y EXIT
Click to close the dialog box.
About the Information window
This window indicates the MIDI and audio data reception status (from the mLAN device to computer).
R1, R2, etc.
This indicates the data reception status. “R1” corresponds to
MIDI reception while “R2 corresponds to audio reception from
the mLAN device. The number of tabs shown differs
depending on your particular computer configuration.
Icon
Blue ........ Reception is normal.
Red......... Error in reception.
Gray........ No reception.
Receive Status
This mark indicates the order in which the data of each format is received. The
symbol “o” indicates that data in the corresponding format is being received. The
symbol “-” indicates that data in a different format is being received. For example, the
symbol “oooooooo-” in the “Audio” field indicates that nine sequences have been
received, and the first eight sequences are in the audio data format. The “Unknown”
field displays symbols if sequences in unknown formats are received. These fields
are blank if no mLAN data is received. If an error occurs during reception, a red
warning message flashes. In this case, check the transmission device.
18
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
If the computer’s system sound is output to mLAN audio channels:
The computer’s system sound (such as an alarm sound) will be output to mLAN audio channels if
the following settings are made:
The WDM driver is selected in mLAN Auto Connector or mLAN Graphic Patchbay.
mLAN WDM driver (mLAN Audio Out/In 01) has been selected for the Windows system audio
device.
Follow the steps below to prevent the system sound from being output to mLAN audio channels.
The following setting cancels output of all Wave sounds from the computer speakers.
1 Select [Start] [Control Panel] [Sounds and Audio Devices] [Voice], and click [Volume…] in
the “Voice playback” section to call up the Master Volume window.
2
Check the Mute checkbox in the Wave column.
19
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Connecting a Computer to an mLAN device via mLAN
This section describes the procedure for
connecting a computer to a single mLAN device
peer-to-peer in mLAN Auto Connector.
In mLAN Auto Connector, you can easily
connect an mLAN device by setting up the
wordclock and the number of audio I/O channels.
To connect multiple mLAN devices to a
computer, use mLAN Graphic Patchbay. For more
information on mLAN Graphic Patchbay, refer to
the mLAN Graphic Patchbay Online Manual.
Noise may be generated during the following operations.
Before performing these operations, lower the output
level of each device.
Turning the power to the computer and mLAN devices
on or off
Connecting or disconnecting an IEEE1394 (mLAN)
cable
Making an mLAN connection in mLAN Auto Connector
Changing the wordclock master and slave status in
mLAN Auto Connector or mLAN Graphic Patchbay
Selecting On or Off in mLAN Manager (Windows)
Starting or quitting the OS
Installing/uninstalling mLAN software
If you use Auto Connector after you make connections
in mLAN Graphic Patchbay, the connections made in
mLAN Graphic Patchbay will be cancelled.
You can also use mLAN Graphic Patchbay to connect
a computer to a single mLAN device peer-to-peer.
The mLAN Auto Connector windows may appear dif-
ferent when certain mLAN devices are connected.
1 Connect a computer to an mLAN device using
an IEEE1394 cable.
2 Right-click the YAMAHA mLAN Manager icon
in the Task bar, then select [Auto Connector].
3 Set up the wordclock and specify the number
of audio channels (see below), then click the
[Connect] button. The computer and mLAN
device are connected via mLAN.
Connecting the i88X
q
w
t
u
!1 !2
!0
e
r
y
i
o
20
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
q Nickname
This field indicates the nickname of the
connected i88X. To change the nickname, refer
to “Node Information” in the mLAN Graphic
Patchbay Online Manual.
w Model Name
This parameter enables you to select an mLAN
device to which you wish to make an mLAN
connection in a multiple mLAN device network.
e [Update] button
Clicking this button updates the information on
the mLAN devices connected to the mLAN
network. Use this button when you add an
mLAN device to the network while mLAN Auto
Connector is running.
r [Identify] button
Clicking this button causes the i88X ACTIVE
indicator to flash for a few seconds.
t Sample Rate
This parameter enables you to specify the
sampling frequency (wordclock frequency).
y Wordclock Master radio buttons
These buttons enable you to specify the
computer or i88X as the wordclock master.
u PC i88X
This parameter enables you to specify the
number of channels of audio data routed from
the computer’s audio output (mLAN driver’s
audio output) into the i88X. Signals input in the
i88X are output from the i88X’s OUTPUT 1-8
jacks (analog), DIGITAL STEREO COAXIAL
or OPTICAL OUT jack (digital), or ADAT OUT
jack (ADAT).
i [ASIO/WDM] button
Select the ASIO or WDM driver as appropriate
for your environment.
With analog connections, WDM will use the last two of
the selected ASIO channels. The WDM channel sig-
nals will be output from OUTPUT 7 and 8.
o PC i88X
This parameter enables you to specify the
number of channels for audio data that is input
at the i88X’s INPUT 1-8 jacks (analog),
DIGITAL STEREO COAXIAL or OPTICAL
IN jack (digital), or ADAT IN jack (ADAT) and
output to the computer.
!0 [Connect] button
Click this button to connect the i88X to the
computer via mLAN.
When the connection is completed, the mLAN
Auto Connector window will close
automatically.
!1 [Cancel] button
Click this button to cancel the settings and close
mLAN Auto Connector.
!2 [Setup] button
Click this button to open the i88X Control Panel
window, which enables you to set the wordclock
transition speed.
21
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Connecting the mLAN16E (MOTIF ES)
q Nickname
This field indicates the nickname of the
connected mLAN16E. To change the nickname,
refer to “Node Information” in the mLAN
Graphic Patchbay Online Manual.
w Model Name
This parameter enables you to select an mLAN
device to which you wish to make an mLAN
connection in a multiple mLAN device network.
When the mLAN16E is connected, select the
name of the device equipped with an
mLAN16E.
e [Update] button
Clicking this button updates the information on
the mLAN devices connected to the mLAN
network. Use this button when you add an
mLAN device to the network while mLAN Auto
Connector is running.
r [Identify] button
Clicking this button causes the mLAN16E
ACTIVE indicator to flash for a few seconds.
t Sample Rate
This parameter enables you to specify the
sampling frequency (wordclock frequency).
y Wordclock Master radio buttons
These buttons enable you to specify the
computer or mLAN16E as the wordclock
master.
u PC MOTIF ES
This parameter enables you to specify the
number of channels of audio data input into the
mLAN16E from the computer’s audio output
(mLAN driver’s audio output).
i [ASIO/WDM] button
Select the ASIO or WDM driver as appropriate
for your environment.
With the MOTIF ES, WDM will use the last two of the
ASIO channels selected via “mLAN INPUT.” The WDM
channel signals will be routed to the MOTIF ES as
“mLAN IN 7/8CH.”
q
w
t
u
!1 !2
!0
e
r
y
i
o
22
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
o PC MOTIF ES
This parameter enables you to specify the
number of channels of audio data input into the
computer from the mLAN16E’s output.
The number of audio transmission channels and MIDI
ports varies on different mLAN16E-compatible
devices.
For more information on audio and MIDI connections
for a MOTIF ES with an mLAN16E installed, refer to
“System Examples” in the mLAN16E Owner’s Manual.
!0 [Connect] button
Click this button to connect the mLAN16E to
the computer via mLAN.
When the connection is completed, the mLAN
Auto Connector window will close
automatically.
!1 [Cancel] button
Click this button to cancel the settings and close
mLAN Auto Connector.
!2 [Setup] button
Click this button to open the mLAN16E Control
Panel window, which enables you to set the
wordclock transition speed.
Connecting the MY16-mLAN
q Nickname
This field indicates the nickname of the
connected MY16-mLAN. To change the
nickname, refer to “Node Information” in the
mLAN Graphic Patchbay Online Manual.
w Model Name
e [Update] button
These are the same functions as for the i88X or
mLAN16E (page 20).
q
w
t
u
!1o
!0
e
r
y
i
23
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
r [Identify] button
Clicking this button causes the MY16-mLAN
ACTIVE indicator to flash for a few seconds.
t Sample Rate
This parameter enables you to specify the
sampling frequency (wordclock frequency).
y Wordclock Master radio buttons
These buttons enable you to specify the
computer or MY16-mLAN as the wordclock
master.
u PC MY16-mLAN
This parameter enables you to specify the
number of channels of audio data routed from
the computer’s audio output (mLAN driver’s
audio output) into the MY16-mLAN.
i PC MY16-mLAN
This parameter enables you to specify the
number of channels of audio data routed from
the MY16-mLAN’s output into the computer’s
input.
o [Connect] button
!0 [Cancel] button
!1 [Setup] button
These are the same functions as for the i88X or
mLAN16E (page 20).
4 Click the [Connect] button. When the mLAN device is connected correctly, mLAN Auto Connector
closes and mLAN communications begin.
If connection fails, right-click the mLAN icon in the Task bar, restart mLAN Auto Connector, then click the [Connect]
button again. You do not need to restart the computer.
Setting the wordclock transition speed (in the mLAN Control Panel)
When you click the [Setup] button in the Node Information window in mLAN Auto Connector or
mLAN Graphic Patchbay, the mLAN Control Panel opens. This panel enables you to set the
wordclock transition speed.
The Wordclock Transition Speed parameter enables you to specify how fast the initial wordclock
setting will change to a new setting if the mLAN device is operating as a slave in an mLAN network.
Slow:
Usually, select this option.
Fast:
Select this option if the wordclock master device is referencing timecode, such as MTC, thus
changing the wordclock setting.
24
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Hints when using audio data (Windows)
For optimum use of the audio functions, we recommend you make the following settings. These settings
minimize possible audio problems, such as drop outs, glitches and noise.
Set the DMA mode (high-speed transfer mode) of the hard disk to on
To set the DMA mode, select [Control Panel] [System] ( [Hardware]) [Device Manager],
then change the setting from [Disk drives] or [Hard disk controllers].
Set Processor Scheduling to “Background services”
Select [Control Panel] [System] [Advanced] [Performance] [Settings] [Advanced]
and check (enable) “Background services” in the “Processor scheduling” section.
Set the Visual Effects options to “best performance”
Select [Control Panel] [System] [Advanced] [Performance] [Settings] [Visual
Effects] and check (enable) “Adjust for best performance.”
Turn Automatic Updates off
Select [Control Panel] [System] [Automatic Updates] and un-check (disable) “Keep my
computer up to date.”
Set Remote Assistance to off
Select [Control Panel] [System] [Remote] and un-check “Allow Remote Assistance invita-
tions...”
Enable the Classic Start menu
Right click on an empty space in the task bar and select [Properties] [Start Menu], then check
(enable) “Classic Start menu.”
Disable transition effects
Select [Control Panel] [Display] ( [Appearance]) [Effects...] button, and un-check (dis-
able) “Use the following transition effect for menus and tooltips.”
25
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
When the settings of the mLAN Auto Connector or Driver Setup cannot be changed, or
when the program mLAN Applications for YAMAHA/mLAN Tools 2.0 cannot be unin-
stalled.
The message below may sometimes appear when changing the settings with mLAN Auto Connector
and Driver Setup or when uninstalling.
When using the mLAN driver with a program such as an audio sequencer, the settings in mLAN Auto
Connector and Driver Setup cannot be changed, and mLAN Applications for YAMAHA/mLAN Tools 2.0
cannot be uninstalled. Execute these operation only after closing all applications.
There may be times when you are unable to change the settings in mLAN Auto Connector and Driver
Setup and unable to uninstall mLAN Applications for YAMAHA/mLAN Tools 2.0, even when applications
are not running. This may occur in the following cases.
The WDM driver is selected in mLAN Auto Connector or mLAN Graphic Patchbay.
When the mLAN WDM driver (“mLAN Audio Out/In 01”) or “mLAN MIDI Out” is selected as the
audio device in Windows.
If this is the case, follow the instructions below before changing the settings in mLAN Auto Connector
and Driver Setup and/or uninstalling mLAN Applications for YAMAHA/mLAN Tools 2.0.
In some cases, when you turn on the power to the mLAN devices, Windows may automatically select mLAN Audio/
MIDI.
1 Select [Start] [Control Panel] [Sounds and Audio Devices] [Voice]. Make sure that something
other than “mLAN Audio Out/In 01” is selected for the “Voice playback” and “Voice recording” set-
tings.
2 Select [Start] [Control Panel] [Sounds and Audio Devices] [Audio]. Make sure that some-
thing other than “mLAN Audio Out/In 01” is selected for the “Sound playback” and “Sound recording”
settings.
3 Select [Start] [Control Panel] [Sounds and Audio Devices] [Audio], then select any option
other than the items from “mLAN MIDI OUT” through “mLAN MIDI OUT (8)” for the “MIDI Music Play-
back” setting.
26
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Installing the Plug-in Effect (For i88X Users)
1
Double-click on the “VST_” folder. Various
files including “Setup.exe” will be displayed.
2 Double-click on “Setup.exe.” “Welcome to the
installShield Wizard” window will be displayed.
3 Click [Next]. In the window that appears, enter
the User Name, Company Name, and Serial
Number.
Serial number is provided in the included Users
Card.
4 Click [Next]. The Registration Confirmation
window will be displayed. Make sure the regis-
tration information you entered is correct, then
click [Yes].
If the information is incorrect, click [No] and return
to step 3 above.
5 A window for selecting plug-in effects will be
displayed. Select (check) the software you
want to install and click [Next].
6 A window appears prompting you for confir-
mation of the plug-in effects to be installed.
Make sure the information is correct, then click
[Yes].
•When you wish to change the software to be
installed, click [Return] and go back to step 5.
7 In the window that appears, you can select the
drive and folder to which the owner’s manual
(PDF file) and setup program will be installed.
You should avoid changing the installation
location.
• If you want to change the location, click [Browse...]
then select the installation location (drive and
folder).
8 Click [Next]. In the window that appears, you
can select the “VstPlugins” folder to which the
plug-in effect will be installed.
In order to be able to use the VST plug-in soft-
ware with the SQ01, it is necessary to check “Pro-
gram Files\YAMAHA\VstPlugins.”
If no folder is shown in the list, click [Add] then
select the folder from the “Browse for Folder” dia-
log box.
9 Click [Next]. The installation starts.
10 When the installation is complete, the mes-
sage “InstallShield Wizard Complete.”
appears. Click [Finish].
27
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Processing speeds of computers equipped with Pen-
tium I processors and some computers equipped with
Pentium IV processors may be reduced significantly if
you use Pitch Fix and Cubase SX2.0.
If this problem occurs, download from the following
URL an updated Pitch Fix Version 1.0.2 or higher:
http://www.yamahasynth.com/down/index.htm
Using the Installed Plug-in
Effect on another host
application
Even after you’ve installed the plug-in effect,
if you intend to use it with another VST-
compatible host application, you will need to
manually copy the effect plug-in module to
the “VstPlugins” folder specified by the host
application.
1 Select [Start] [(All) Programs]
[YAMAHA VST Plugins] [(Plug-in Effect
name)] [Setup].
A “Welcome” window appears.
2 Select [Modify], then click [Next].
3 A window appears allowing you to specify
the destination location to which the plug-in
effect is to be copied. Select (check) the
“VstPlugins” folder corresponding to the
host application with which you intend to
use the plug-in effect.
If you remove the checkmark from the folder
for the installed host-application, you can
remove the installed plug-in effect.
For details, refer to the owner’s manual of
each host application.
4 Click [Next].
The copy operation is executed.
To cancel the operation, click [Cancel].
Uninstall (removing the installed
plug-in effect)
1 Select [Start] [(All) Programs]
[YAMAHA VST Plugins] [(Plug-in Effect
name)] [Setup].
A “Welcome” window appears.
2 Select [Remove], then click [Next].
A window appears prompting you for con-
firmation of the file deletion.
3 Click [OK] to remove the files.
To cancel the operation, click [Cancel].
28
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Only the i88X and mLAN16E support Mac OS 9. The MY16-mLAN does not support Mac OS 9.
Regarding Mac OS X, refer to page 42.
CD-ROM Contents
Software for Macintosh is included on two CD-ROMs (for the mLAN 16E, only TOOLS for i88X/
mLAN16E is included). Install TOOLS for i88X/mLAN16E first.
TOOLS for i88X/mLAN16E
Plug-in Effect (included only with i88X)
This software can be used as plug-in software within a VST/Audio Units compatible program.
•For instructions on how to use the application, refer to the PDF manual.
(The destination disk you specified)/YAMAHA/Plug-in Effect/(the relevant software folder)
•For instructions on installing the Plug-in Effects, see page 41.
For Mac OS 9 Users (i88X and mLAN16E only)
Folder Name Application Name Contents
mLAN_
mLAN Applications
for YAMAHA
mLAN Tools
This software includes mLAN drivers and applications required to make
mLAN connections between the mLAN devices and the computer.
Install the software while the power to the mLAN devices is off.
• For installation instructions, see page 31.
A single installation procedure installs all applications necessary for
mLAN communications. Software to be installed includes mLAN Auto
Connector and mLAN Graphic Patchbay, which enable you to set up
audio and MIDI connections for an mLAN network.
OMS_
Open Music System
(OMS) 2.3.8
*2
This software is required to transfer MIDI data (Remote Control and
Studio Manager data) between an mLAN device and a computer.
• For instructions on installing, see page 32.
OMS Setup for
YAMAHA (folder)
Contains OMS Setup files for an mLAN device (page 39).
29
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
*1 These applications are supplied with online/PDF manuals.
*2 Unfortunately, Yamaha makes no guarantee concerning the stability of these programs nor can it offer
user support for them.
*3 Mac OS X Compatibility
You can download mLAN software compatible with Mac OS X at the following URL:
mLAN driver (included in OS X 10.3.3 or higher)
<http://www.apple.com/support/>
mLAN Tools, Studio Manager for 01X
<http://www.yamahasynth.com>
The following plug-in effects are included in the “Mac OS X” folder and are compatible with VST and
Audio Units.
01X Channel Module
Pitch Fix
•Vocal Rack
Final Master
Folder Name Application Name Contents
Mac OS 9
*3
VST_
01X Channel
Module
*1
This software reproduces the EQ and Dynamics effects built
into each channel of the YAMAHA Digital Mixing Studio 01X,
and uses the processing power of the computer for the effects.
You can use the Dynamics and 4-band EQ functions (that can
be also found on Yamaha Digital Mixing consoles) as effects
software. You can also import the 01X settings, thus
reproducing the songs created on the 01X.
Pitch Fix
*1
This program is used to edit the pitch of recorded vocals. More
than just a pitch processor, it can also be used to change the
character of the vocals. Moreover, you can use MIDI data on the
host application to control the Pitch Fix effect. For more
information on setting up with the host application, refer to the
Pitch Fix PDF owner’s manual.
Vocal Rack
*1
This is a multi-effect program for processing vocals. The plug-in
features various effects, including a high-pass filter, compressor
and a 3-band equalizer.
Final Master
*1
This is a multi-effect program for mastering purposes. It
features a compressor, limiter and soft-clip function, and allows
you to split the signal into three bands for separate multi-band
processing.
With Macintosh notebook computers such as the iBook or PowerBook, before you start up the com-
puter, first connect the mLAN device and mLAN cable, then turn on the power to the mLAN device.
30
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
System Requirements for i88X/mLAN16E Software
The system requirements below are necessary for using the included software.
The system requirements below may differ slightly depending on the particular operating system.
For details on minimum requirements for each DAW (Digital Audio Workstation) software, refer to the respective owner’s
manual.
i88X/mLAN16E (including the require-
ments for mLAN Tools 2.0/mLAN Appli-
cations for YAMAHA)
These are the total system requirements,
including the audio sequencer, mLAN Tools
2.0/mLAN Applications for YAMAHA and
the plug-in effects.
OS : Mac OS 9.2 (Mac OS X and Mac
Classic environment are not sup-
ported.)
Computer : System having a built-in S400 (400
Mbps) FireWire terminal. (*1)
Hard Disk : Free disk space of 250 MB (i88X)/50
MB (mLAN16E) or more; high-
speed hard disk
Recommended system (*2)
Connecting a single mLAN device to a com-
puter peer-to-peer:
Computer :
G4/G3 signal processor
900 MHz (or higher)
Available Memory : 512 MB or more (Vir-
tual memory must be
turned off)
Connecting three mLAN devices to a com-
puter:
Computer : G4 1.25GHz Single
processor, 1GHz Dual
processor, or higher
Available Memory : 512 MB or more (Vir-
tual memory must be
turned off)
Minimum system requirements (*2)
Computer : G4 dual processor
450 MHz or G4/G3
single processor 700
MHz (or higher)
Available Memory : 320 MB or more (Vir-
tual memory must be
turned off)
*1 The computer must have an IEEE 1394
(FireWire) or i.Link terminal. If there is no ter-
minal, install an IEEE 1394 interface card
(PCI or PC).
For more details on system requirements and
recommended PCI or PC cards, see
http://www.yamahasynth.com
*2 The system requirements listed here apply
when using the included software and when
playing audio/MIDI data detailed below on
standard sequencer software. This may differ
depending the particular sequencer software
you are using.
Recommended system requirements (Connecting
a single mLAN device to a computer peer-to-peer)
Fs=44.1kHz/24-bit
Audio Driver
18In/18Out (i88X)
16In/8Out (mLAN16E)
MIDI Driver
1In/1Out (i88X)
3In/3Out (mLAN16E)
16 MIDI and 12 Audio playback tracks
2 Audio recording tracks
2 Sends for Plug-in Soft Effect
10 Inserts for Plug-in Soft Effect
2 Channels for Plug-in Soft Synthesizer
Latency of 5msec or less
Recommended system requirements (Connecting
a computer and three mLAN devices)
Fs=44.1kHz/24-bit
Audio Driver 32In/32Out (total)
MIDI Driver 4In/5Out (total)
16 MIDI and 8 Audio playback tracks
2 Audio recording tracks
2 Sends for Plug-in Soft Effect
10 Inserts for Plug-in Soft Effect
2 Channels for Plug-in Soft Synthesizer
Latency of 5msec or less
Minimum system requirements
Fs=44.1kHz/16bit
Audio Driver
8In/2Out (i88X)
2In/2Out (mLAN16E)
MIDI Driver
1In/1Out (i88X)
2In/2Out (mLAN16E)
16 MIDI and 12 Audio playback tracks
2 Sends for Plug-in Soft Effect
6 Inserts for Plug-in Soft Effect
No Plug-in Soft Synthesizer
Latency of about 50msec
31
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Up to two PCI or PC cards can be used. However,
you can use only one card at a time.
If you are using an IEEE1394 interface built into the
computer, you can use only one IEEE1394 PCI or
PC interface card.
When using a laptop or notebook computer, a built-
in IEEE 1394 terminal may not be available. If this is
the case, install an appropriate PC interface card.
Plug-in Effect (included only with i88X)
OS : Mac OS 8.6 through 9.2
Mac OS X 10.2 through 10.3
When using a PowerBook under battery power,
go Apple menu [Control Panel] [Energy
Saver] [Advanced Settings] (Settings for: Bat-
tery), and remove the check from the “Allow pro-
cessor cycling.”
Software Installation
mLAN software and OMS
mLAN Tools 2.0 software includes a driver that enables you to connect mLAN devices to a computer.
mLAN Applications for YAMAHA enables audio and MIDI signals to be transferred between a
computer and mLAN devices via mLAN cables. This software enables you to connect the i88X,
mLAN16E, or 01X to a computer via mLAN.
Follow the steps below to install these software applications.
For explanations on error messages, see page 43.
For information on the uninstall (removing the installed
application), refer to page 33.
Preparing to install
1 Start the computer.
•When using the mLAN connection, make sure
to disable any energy saving features on the
computer (such as Suspend, Sleep, Standby
or Pause). When using the virtual memory,
turn it off, then restart the computer.
If you are using the S200 data transfer rate stan-
dard (check the rear panel of your particular
device, or refer to the specifications in the owner’s
manual), make sure to uninstall the old version of
mLAN Tools beforehand. (Refer to the owner’s
manual of your particular device.)
2 Exit from any open applications and close all
open windows.
3 Disconnect all MIDI cables connecting MIDI
devices to the MIDI IN/OUT of the mLAN
device.
4 Using an IEEE1394 (FireWire/iLink) cable,
connect the mLAN device directly to the com-
puter (without use of a hub), and disconnect
all other IEEE1394-connected devices from
the computer.
5 Insert the included CD-ROM (“TOOLS for
i88X/mLAN16E”) into the CD-ROM drive.
For instructions on how to install the software other than one referred to below, see page 28 in the
section “CD-ROM Contents.”
32
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
OMS (Open Music System)
6 Double-click on the “OMS_” folder (English
version only).
“Install OMS 2.3.8” will be displayed.
7 Double-click on “Install OMS 2.3.8.”
OMS Setup Dialog will be displayed.
8 Execute the installation by following the on-
screen directions.
After the installation, select “Restart.
After the installation is complete, you may
encounter an error message warning that the
installer did not close. In this case, go to the “File”
menu and select “Quit” to close the installer. Then
reboot the computer.
9 After restarting the Macintosh, you will find the
“Opcode”/“OMS Applications” folder on your
computer (Hard Disk, as the default).
10 Copy the “OMS_2.3_Mac.pdf” in the CD-
ROM to the “OMS Applications” folder
(drag-and-drop it to the folder).
Refer to the “OMS_2.3_Mac.pdf” (English
version only) for information on how to use
the application.
11 Copy the “OMS Setup for YAMAHA” in the
CD-ROM to the “OMS Applications” folder
(drag-and-drop it to the folder).
In the “OMS Setup for YAMAHA” folder you
will find the OMS Setup files for the i88X
and mLAN16E, which can be used as tem-
plates.
mLAN software
12 Double-click the “YAMAHA mLAN Installer”
icon in the “mLAN_” folder to display the fol-
lowing installation screen. The “Install Loca-
tion” box displays the destination of the
installation. If you wish to change the desti-
nation disk or folder, use the [Switch Disk]
button and the pop-up menu to specify the
desired destination.
In general, there is no need to change the desti-
nation directory.
13 Confirm that “Easy install” is selected and
click “Install.” At the confirmation message
that appears, click “Continue.”
14 If a message “OMS Folder cannot be found
in the system folder” or the like appears,
after finishing the installation, copy the file
“mLAN OMS Driver” (located in “Into OMS
Folder” of the “mLAN Tools” folder in the
installation destination) to the system folder
“OMS Folder.”
15 The message prompting to search the
ASIO Drivers folder is shown. Click [OK].
The result of the search will be displayed.
33
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
16 Select the installation destination of the
ASIO mLAN Driver, then click [OK].
If a message “ASIO Driver folder cannot be found
in the system folder” or the like appears, after fin-
ishing the installation, copy the file “ASIO mLAN”
(located in “Into ASIO Drivers” of the “mLAN
Tools” folder in the installation destination) to the
“ASIO Drivers” folder of the particular application
you are using.
17 Turn on the mLAN device.
18 When installation is finished, an “Installation
was successful.” message appears. Click
[Restart].
Confirming the installation
The mLAN Installer places the following files in
the following locations.
Control panel folder of the startup disk
mLAN Driver Setup (page 34)
You can use the mLAN Driver Setup (page 34) to
check whether data is being properly transmitted and
received via mLAN.
Extensions folder of the startup disk
mLAN Driver
mLAN Driver Plugs
mLAN Expert
mLAN Family
mLAN Transporter Family
The folder you specify
mLAN Tools folder
Opcode/OMS Applications
System folder
Control Panels/mLAN Driver Setup
OMS Folder/mLAN OMS Driver
Preferences/mLAN HALs/01XTransporter.hal
Preferences /mLAN HALs/i88XTransporter.hal
Preferences /mLAN HALs/
mLAN16ETransporter.hal
Preferences /mLAN Prefs/mLAN Control Panel
Prefs
Preferences /mLAN Prefs/oui.tbl
* Delete the files and folders listed above when
uninstalling. Be careful not to delete data
already existing before the installation,
including files related to OMS.
34
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Changing settings after installation
The mLAN-related settings can be changed after installation from the mLAN Driver Setup window. To
display it, start the mLAN Driver Setup in the Control Panels folder.
mLAN Driver Setup
This window lets you check and change the mLAN settings for receiving/transmitting data. Make sure
to close any application (DAW, etc.) using the mLAN connection before making changes.
To change the wordclock (sample rate) and the number of channels used, Start the mLAN Auto Connector in the mLAN
Tools folder.
q FireWire Card ID
The options here are the same as those for the 1394 Adapter Card ID parameter for Windows as
described on page 15.
w Latency
Determines the basic latency of the mLAN communications, or how quickly the data is processed after
a command is issued. Choose an option appropriate to your environment.
q
w
e
t r
About latency in an mLAN network
The particular configuration of your computer (processing speed, system memory size, etc.) may affect
its ability to properly record and play back audio data in your audio sequencer, resulting in noise or other
audio problems. In most cases, you can solve the problem by adjusting the latency (delay time).
•A small latency value results in a short delay time and gives optimum response for real-time
recording/playback.
•A large latency value results in a long delay time, but allows for use of more audio channels and
plug-in effects.
Types of latency in an mLAN network
Audio latency (msec)
Audio latency is determined by the basic latency (selected in the mLAN Driver Setup window) and Pre-
ferred Buffer Size (specified in the ASIO mLAN Control Panel) (see next page).
MIDI latency (msec)
The MIDI latency value varies with the mLAN driver version.
For information on the MIDI latency of your mLAN driver version, refer to the “MIDI_Latency.txt” file,
which you can access by selecting [mLAN Tools | YAMAHA | Manual] on the corresponding computer.
35
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
e Status
r Set
t Revert
The field and buttons function the same as those for Windows as described on page 17.
ASIO mLAN Control Panel.
When using the mLAN ASIO Driver, open the ASIO Control Panel within the driver settings of the DAW
software (the particular menu depends on the software you are using) and set the Preferred Buffer Size
as needed.
The initial setting of the Preferred Buffer Size of the mLAN ASIO driver is the smallest value.
q FireWire Card ID
The options here are the same as those for the 1394 Adapter Card ID parameter for Windows as
described on page 15.
r Latency
It indicates the audio latency value for transmission and reception.
Audio latency is determined by the basic latency (selected in the mLAN Driver Setup window) and
Preferred Buffer Size (w).
w Preferred Buffer Size
e Sample Size
t OK
y Cancel
The parameters and buttons function the same as those in the ASIO mLAN Control Panel for
Windows as described on page 16.
q
w
e
t y
r
36
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Connecting a Computer to an mLAN device via mLAN
This section explains how to connect a computer
to a single mLAN device peer-to-peer in mLAN
Auto Connector.
In mLAN Auto Connector, you can easily connect
an mLAN device by setting up the wordclock and
specifying the number of audio I/O channels.
To connect multiple mLAN devices to a
computer, use mLAN Graphic Patchbay. For more
information on mLAN Graphic Patchbay, refer to
the mLAN Graphic Patchbay Online Manual.
Noise may be generated during the following operations.
Before performing these operations, lower the output
level of each device.
Turning the power to the computer and mLAN devices
on or off
Connecting or disconnecting an IEEE1394 (mLAN)
cable
Making an mLAN connection in mLAN Auto Connector
Changing the wordclock master and slave status in
mLAN Auto Connector or mLAN Graphic Patchbay
Selecting On or Off in mLAN Manager (Windows)
Starting or quitting the OS
Installing/uninstalling mLAN software
If you use Auto Connector after you make connections
in mLAN Graphic Patchbay, the connections made in
mLAN Graphic Patchbay will be cancelled.
You can also use mLAN Graphic Patchbay to connect
a computer to a single mLAN device peer-to-peer.
mLAN Auto Connector windows may appear different
when certain mLAN devices are connected.
1 Connect a computer to an mLAN device using
an IEEE1394 cable.
2 Open the “mLAN Tools” folder, then click the
“mLAN Auto Connector” icon.
mLAN Auto Connector starts.
3 Set up the wordclock and specify the number
of audio channels (see below), then click the
[Connect] button. The computer and mLAN
device are connected via mLAN.
Connecting the i88X
q Nickname
This field indicates the nickname of the
connected i88X. To change the nickname, refer
to “Node Information” in the mLAN Graphic
Patchbay Online Manual.
w Model Name
This parameter enables you to select an mLAN
device to which you wish to make an mLAN
connection in a multiple mLAN device network.
q
w
t
u
!0 !1
o
e
r
y
i
37
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
e [Update] button
Clicking this button updates the information on
the mLAN devices connected to the mLAN
network. Use this button when you add an
mLAN device to the network while mLAN Auto
Connector is running.
r [Identify] button
Clicking this button causes the i88X ACTIVE
indicator to flash for a few seconds.
t Sample Rate
This parameter enables you to specify the
sampling frequency (wordclock frequency).
y Wordclock Master radio buttons
These buttons enable you to specify the
computer or i88X as the wordclock master.
u Mac i88X
This parameter enables you to specify the
number of channels of audio data routed from
the computer’s audio output (mLAN driver’s
audio output) into the i88X. Signals input in the
i88X are output from the i88X’s OUTPUT 1-8
jacks (analog), DIGITAL STEREO COAXIAL
or OPTICAL OUT jack (digital), or ADAT OUT
jack (ADAT).
i Mac i88X
This parameter enables you to specify the
number of channels for audio data that are input
at the i88X’s INPUT 1-8 jacks (analog),
DIGITAL STEREO COAXIAL or OPTICAL
IN jack (digital), or ADAT IN jack (ADAT) and
output to the computer.
o [Connect] button
Click this button to connect the i88X to the
computer via mLAN.
!0 [Cancel] button
Click this button to cancel the settings and close
mLAN Auto Connector.
!1 [Setup] button
Click this button to open the i88X Control Panel
window, which enables you to set the wordclock
transition speed.
Connecting the mLAN16E (MOTIF ES)
q
w
t
u
!0 !1
o
e
r
y
i
38
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
q Nickname
This field indicates the nickname of the
connected mLAN16E. To change the nickname,
refer to “Node Information” in the mLAN
Graphic Patchbay Online Manual.
w Model Name
This parameter enables you to select an mLAN
device to which you wish to make an mLAN
connection in a multiple mLAN device network.
When the mLAN16E is connected, select the
name of the device equipped with an
mLAN16E.
e [Update] button
Clicking this button updates the information on
the mLAN devices connected to the mLAN
network. Use this button when you add an
mLAN device to the network while mLAN Auto
Connector is running.
r [Identify] button
Clicking this button causes the mLAN16E
ACTIVE indicator to flash for a few seconds.
t Sample Rate
This parameter enables you to specify the
sampling frequency (wordclock frequency).
y Wordclock Master radio buttons
These buttons enable you to specify the
computer or mLAN16E as the wordclock
master.
u Mac MOTIF ES
This parameter enables you to specify the
number of channels of audio data input into the
mLAN16E from the computer’s audio output
(mLAN driver’s audio output).
i Mac MOTIF ES
This parameter enables you to specify the
number of channels of audio data input into the
computer from the mLAN16E’s output.
The number of audio transmission channels and MIDI
ports varies on different mLAN16E-compatible
devices.
For more information on audio and MIDI connections
for an MOTIF ES with an mLAN16E installed, refer to
“System Examples” in the mLAN16E Owner’s Manual.
o [Connect] button
Click this button to connect the mLAN16E to
the computer via mLAN.
!0 [Cancel] button
Click this button to cancel the settings and close
mLAN Auto Connector.
!1 [Setup] button
Click this button to open the mLAN16E Control
Panel window, which enables you to set the
wordclock transition speed.
4 Click the [Connect] button. When the mLAN
device is connected correctly, mLAN Auto
Connector closes and mLAN communications
start.
If connection fails, restart mLAN Auto Connector,
then click the [Connect] button again. You do not
need to restart the computer.
Setting the wordclock transition speed
(mLAN Control Panel)
When you click the [Setup] button in the
Node Information window in mLAN Auto
Connector or mLAN Graphic Patchbay, the
computer displays the mLAN Control Panel,
which enables you to set the wordclock
transition speed.
The Wordclock Transition Speed parameter
enables you to specify how fast the initial
wordclock setting will change to a new
setting if the mLAN device is operating as a
slave in the mLAN network.
Slow:
Select this option in most cases.
Fast:
Select this option if the wordclock master
device is referencing timecode, such as
MTC, thus changing the wordclock setting.
39
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Setting up OMS
If you are using mLAN on your Macintosh with an
optionally installed IEEE 1394 (FireWire) interface
card, recreate a new Studio Setup by OMS Setup
included in the installation CD-ROM. For details, refer
to the OMS manual.
1 Double-click on the “OMS” folder and “OMS-
Setup for YAMAHA” folder. The “i88X-mLAN,”
“MOTIF-ES-mLAN” and “mLAN Generic 16
ports” files appear. Copy this to the hard disk
on your computer.
2 If you are connecting a single i88X or
mLAN16E (including MOTIF ES) using Auto
Connector, double-click “i88X-mLAN” or
“MOTIF ES-mLAN.”
If you are connecting multiple mLAN devices
using Graphic Patchbay or connecting a sin-
gle mLAN16E (excluding MOTIF ES) using
Auto Connector, double-click “mLAN Generic
16 Ports.” The OMS Setup starts.
3 After starting the OMS Setup, the Studio setup
file double-clicked in step
2 opens.
If “ ” is not indicated at the right of the setup
file name, select “Make Current” from the
“File” menu and execute the save operation.
The OMS studio setup has been completed.
You’ll also need to set the OMS port when
using the software.
Refer to the owner’s manual for your applica-
tion.
Double clicking the icon of the mLAN device or
executing “MIDI Device Info...” from the “Studio”
menu by selecting the mLAN device, calls up the
Device Info dialog box. We recommend that you
not change the channel assignment since this is
already set by the setup application (mLAN Auto
Connector, etc.) for optimum use with i88X and
mLAN16E. Reset the settings as shown in the
illustration below if you have inadvertently
changed them.
The setting names (device names) of each
MIDI port are as shown below, when the Stu-
dio Setup file is loaded. Select the proper
device (port) for the application you are using.
i88X (Auto Connector) port function
MOTIF ES (Auto Connector) port function
You can assign a function to each MIDI port on the
MOTIF ES. This example uses typical device
names.
Port functions in mLAN Graphic Patchbay and
on the mLAN16E (excluding MOTIF ES)
MIDI
Port
Device Name Function
1 MIDI
i88X’s MIDI port (MIDI to
(from) mLAN MIDI
conversion)
MIDI
Port
Device Name Function
1TG Controls a tone generator.
2 PLG Controls a Plug-in.
3 Remote B Controls a DAW or editor.
4 Remote A Controls a DAW or editor.
MID Port Device Name Function
1Port 1
Port functions vary
depending on the specific
mLAN device. Refer to the
owner’s manual for your
mLAN device.
2Port 2
. . . . . . . .
16 Port 16
40
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
The port numbers in the “mLAN Generic 16 ports” Stu-
dio Setup correspond to the numbers indicated in the
“Connector Name” column in mLAN Graphic Patch-
bay. For more information on Graphic Patchbay, refer
to the Graphic Patchbay Online Manual.
After the OMS studio setup above has been com-
pleted, your computer will recognize only Yamaha
mLAN (MIDI) devices. If you are connecting other
musical instruments via USB, or if you add an mLAN
(MIDI) device to the network while you are already
using OMS, you should create an original Studio Setup
file. For details, refer to the on-line manual supplied
with OMS.
The included OMS studio setup file may not function
even if you follow the above procedure, depending on
your Macintosh/Mac OS version. (MIDI data cannot be
transmitted/received even if the setup becomes avail-
able.) In this situation, connect your Macintosh to the
mLAN device and follow the procedure below to re-
create the setup file.
1 Start OMS Setup and select “New Setup” from the
“File” menu.
2 The “OMS Driver Search” dialog appears.
Remove the check from the “Modem” and
“Printer” check boxes, and click [Search] to exe-
cute the device search. If the Search operation
has been completed successfully, the [mLAN-01]
device is displayed in the OMS driver setting dia-
log.
3 Click the [OK] button to search for ports. If you are
using the i88X or mLAN16E, Port 1, Port 2 ...
appears in the dialog. Mark the appropriate
checkbox of the port and click the [OK] button to
store the setting.
41
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Plug-in Effect
1
Double-click on the “Mac OS 9” folder. “VST_”
folder will be displayed.
2 Double-click on the “VST_” folder. “VST Plu-
gin Installer.” will be displayed.
3 Double-click on “VST Plugin Installer.”
A window for selecting plug-in effects will be
displayed.
In the window, the “Install Location” box dis-
plays the destination of the owner’s manual
(PDF file). You should avoid changing the
installation location. Select (check) the soft-
ware you want to install.
4 Click [Install]. In the window that appears,
enter the User Name, Company Name, and
Serial Number.
Serial number is provided in the included Users
Card.
5 Click [Continue]. In the window that appears,
you can select the “VstPlugins” folder to which
the plug-in effect will be installed.
If there is only one “VstPlugins” folder in your
computer, this step is unnecessary. Go on to step
7.
If there is no “VstPlugins” folder in your computer,
you can select the location to which the plug-in
effect will be installed, in the window that appears.
6 Click [OK]. The installation starts.
7 When the installation is complete, the follow-
ing screen appears.
8 To finish the installation, click [Quit]. To copy
the module to a location other than selected in
step 5 above, click [Continue] and repeat the
procedure from step 3.
42
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
The included CD-ROM does not include mLAN software for Mac OS X. If you will be using the i88X,
mLAN16E, or MY16-mLAN with Mac OS X, please download the following software from the URLs
listed below.
mLAN driver (OS X10.3.3 or higher)
<http://www.apple.com/support/>
mLAN Tools
<http://www.yamahasynth.com>
For i88X users
The software included in the Mac OS X folder of the CD-ROM (Plug-in Effect) is VST/Audio Units compatible versions of
the 01X Channel Module, Pitch Fix, Vocal Rack, and Final Master that can be used with Mac OS X.
For Mac OS X Users
43
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
** will be the name of the mLAN device you’re using.
Display Messages
Messages Page
Can’t find the ** on the mLAN network.
Make sure that the ** is turned on and that the mLAN cable connection is correct and
secure. After that, restart “mLAN Auto Connector”.
19, 36
The settings of the mLAN Driver could not be changed.
1) If an application that uses the driver is currently active, close it first, then change
the settings.
2) There is not enough resource memory.
25
Failed to initialize the mLAN settings because the application “mLAN Start” is not run-
ning.
Select “ON” from the menu of “mLAN Manager” application.
14
Can’t connect the **’s mLAN audio output connector to the computer’s mLAN audio
input connector.
14, 19,
36
Can’t connect the **’s mLAN MIDI output connector to the computer’s mLAN MIDI
input connector.
14, 19,
36
Can’t connect the computer’s mLAN MIDI output connector to the **’s mLAN MIDI
input connector.
14, 19,
36
Can’t connect the computer’s mLAN wordclock output connector to the **’s mLAN
wordclock input connector.
14, 19,
36
Can’t connect the **’s mLAN wordclock output connector to the computer’s mLAN
wordclock input connector.
14, 19,
36
A new 1394 adaptor card has been found.
If you’ve inserted a new card, restart the computer.
There is not enough resource memory.
Execute mLAN Stop, then execute mLAN Start again. If this fails, restart the computer.
14
The 1394 adaptor card has not been found.
Check the card and start mLAN again.
14
One of the programs could not be started. Follow the instructions/messages in the
appropriate application. If there are no messages, execute mLAN Start again or restart
the computer.
14
The application is not responding.
Execute mLAN Start again or restart the computer.
14
Failed to load the mLAN Bus Driver.
If the New Hardware Wizard has not been run, use it to install the hardware, then exe-
cute mLAN Start.
14
One or more programs could not be closed.
After quitting all DAW programs and any programs using mLAN, execute mLAN Stop.
14
44
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
If you encounter a problem...
If you hear no sound or a strange sound, first check the items described below and take appropriate
action. If the problem persists, consult your Yamaha dealer.
Unable to communicate via mLAN
Has the driver been installed? ................................................................................ See page 12.
Is the mLAN cable properly connected? Check the connection; disconnect the mLAN cable
once, then insert it again.
(For Windows) Is mLAN set to “ON”? From the task bar, right click on the mLAN Manager icon.
........................................................................................................... See page 14.
(For Windows) When adding a new IEEE 1394 card, right click on the mLAN Manager icon in the
task bar and select “ON.”. ..................................................................................... See page 14.
Is the ACTIVE lamp on the rear panel of the mLAN device lit (in blue)? If it is not lit, check the fol-
lowings:
- In mLAN Driver Setup, is the Status indicator blue? If not, restart the mLAN device and re-
enable connection by using mLAN Auto Connector or mLAN Graphic Patchbay.
........... Refer to page 19, page 36, and “mLAN Connection Settings” in the mLAN
Graphic Patchbay Online Manual.
Has connection been enabled with mLAN Auto Connector and/or Graphic Patchbay? Re-enable
connection if necessary.
........... Refer to page 19, page 36, and “mLAN Connection Settings” in the mLAN
Graphic Patchbay Online Manual.
Have you changed the device? Even if the model is the same, if the actual device is different, it is
necessary to re-enable connection by using Auto Connector and/or Graphic Patchbay.
........... Refer to page 19, page 36, and “mLAN Connection Settings” in the mLAN
Graphic Patchbay Online Manual.
Is there a loop connection? Check the cabling and make sure none of the devices are connected
in a loop.
There may be a limit on the IEEE 1394 interface of your computer as to the number of ports that
can be used simultaneously. Check how many ports can be used simultaneously.
•Turn off all devices on the mLAN network (except the computer) and re-connect each device
one-by-one until the device causing the problem is found.
(For Windows) (When removing the mLAN bus from the [Safely Remove Hardware] setting of
the task bar.) Restart the computer when using mLAN again.
•With Macintosh notebook computers such as the iBook and PowerBook, always first connect the
mLAN device and mLAN cable then turn on the power of the mLAN device, before starting up
the computer.
Troubleshooting
Computer
Computer
mLAN device
mLAN device
: IEEE1394-equipped device
Example of loop connection
45
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
Make sure that you set up the wordclock correctly. Also, make sure that one node is assigned as
master and the other nodes are assigned as slaves.
........... Refer to “mLAN Connection Settings” in the mLAN Graphic Patchbay
Online Manual.
The computer processing speed is too slow.
The computer’s CPU meter indicates a heavy processing load.
Playback response is delayed.
If multiple S200-compatible devices are connected to the network, connecting mLAN devices in
mLAN Graphic Patchbay may require more time.
Inconsistency in wordclock, or unable to exit from Auto Connector
(For Windows) Mobile computers with Intel CPU
SpeedStep ™ technology is applied for some CPU’s (CPU for notebook PC). Please disable the
SpeedStep ™ technology when mLAN is employed. SpeedStep ™ technology changes CPU
clock dynamically depending on the loading on the CPU to save the power consumption.
- How to disable the SpeedStep™ technology;
In almost all of the PC’s, BIOS has a function to select enabling or disabling the SpeedStep™
technology. Please refer to the PC’s operating manual, or make inquiry to the PC manufac-
turer.
Unable to change the mLAN settings
(For Windows) Is the mLAN (WDM) driver selected as the default audio device for the system?
- Select [Start | Control Panel | Sounds and Audio Devices | Voice].
Make sure that something other than “mLAN Audio 01” is selected for the [Voice playback]
and [Voice recording] settings.
- Select [Start | Control Panel | Sounds and Audio Devices | Audio].
Make sure that something other than “mLAN Audio 01” is selected for the [Sound playback]
and [Sound recording] settings.
- In “MIDI music playback,” select any option other than the range of options from “mLAN
MIDI Out” through “mLAN MIDI Out (8).”
(For Windows) Select [Start | Control Panel | Sounds and Audio Devices | Sounds]. And select
“No sounds” in the [Sound scheme], then execute again.
If you cannot quit mLAN (by selecting “OFF” after right clicking the mLAN icon in the task bar),
end the processes listed below manually. ([Ctrl] + [Alt] + [Delete] [Processes] select process
[End process]) When finished, start mLAN Manager to change the mLAN settings again.
- mLANVDevice.exe
- mLANTFamily.exe
- mLANSoftPH.exe
- mLANManager.exe
•To change mLAN settings, select [Start | (All) Programs | Start Up], then start mLAN Manager.
(When a message such as “file cannot be found” appears when uninstalling:)
Try executing the installation once more, then uninstall again.
(Windows) mLAN Manager (the mLAN icon in the Task bar) has disap-
peared.
Select [Start | (All) Programs | Start Up (or mLAN Tools)], then select mLAN Manager.
46
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
English
A connected mLAN device is not recognized.
Refresh the information by selecting [View], then [Update] in the Menu bar. If the device is still
not recognized, turn mLAN Manager off, then turn it on, then select [Update] to latest informa-
tion. ........... Refer to “Starting mLAN Graphic Patchbay” in the mLAN Graphic Patchbay
Online Manual.
Launching mLAN Graphic Patchbay or updating to the latest informa-
tion takes a while.
When you try to update the network information after connecting or disconnecting an mLAN
device that does not support S400, the system adjusts the mLAN transfer speed, and requires
more time to process your request. However, this will not affect any subsequent operations.
If five or more mLAN devices (including a computer) have been connected to a network, the
total number of transmission channels of all devices will be limited. You can connect up to 86
channels in Windows and up to 98 channels in a Macintosh system.
For information on audio problems such as no sound or excess noise, refer to the Troubleshooting section of the i88X/
mLAN16E/MY16-mLAN Owner’s Manual.
47
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide
SOFTWARE LICENSING AGREEMENT
The following is a legal agreement between you, the end user, and Yamaha Corporation (“Yamaha”). The
enclosed Yamaha software program is licensed by Yamaha to the original purchaser for use only on the terms
set forth herein. Please read this licensing agreement with care. Opening this package indicates that you accept
all terms outlined herein. If you do not agree to the terms, return this package unopened to Yamaha for a full
refund. In the event that you obtained the enclosed Yamaha software program(s) as a part of a software
package or software bundled with a hardware product, you may not return the enclosed Yamaha software
program(s) to Yamaha.
1. GRANT OF LICENSE AND COPYRIGHT
Yamaha grants you, the original purchaser, the right to use one copy of the enclosed software program and
data (“SOFTWARE”) on a single-user computer system. You may not use it on more than one computer or
computer terminal. The SOFTWARE is owned by Yamaha and is protected by Japanese copyright laws and all
applicable international treaty provisions. You are entitled to claim ownership of the media in which the
SOFTWARE is included. Therefore, you must treat the SOFTWARE like any other copyrighted materials.
2. RESTRICTIONS
The SOFTWARE program is copyrighted. You may not engage in reverse engineer-ing or reproduction of the
SOFTWARE by other conceivable methods. You may not reproduce, modify, change, rent, lease, resell, or
distribute the SOFTWARE in whole or in part, or create derivative works from the SOFTWARE. You may not
transmit or network the SOFTWARE with other computers. You may transfer ownership of the SOFTWARE
and the accompanying written materials on a permanent basis provided that you retain no copies and the
recipient agrees to the terms of the licensing agreement.
3. TERMINATION
The licensing condition of the software program becomes effective on the day that you receive the
SOFTWARE. If any one of the copyright laws or clauses of the licensing conditions is violated, the licensing
agreement shall be terminated automatically without notice from Yamaha. In this case, you must destroy the
licensed SOFTWARE and its copies immediately.
4. PRODUCT WARRANTY
Yamaha warrants to the original purchaser that if the SOFTWARE, when used in normal conditions, will not
perform the functions described in the manual provided by Yamaha, the sole remedy will be that Yamaha will
replace any media which proves defective in materials or workmanship on an exchange basis without charge.
Except as expressly set forth above, the SOFTWARE is provided “as is,” and no other war-ranties, either
expressed or implied, are made with respect to this software, including, without limitation the implied
warranties of merchantability and fitness for a particular purpose.
5. LIMITED LIABILITY
Your sole remedies and Yamaha’s entire liability are as set forth above. In no event will Yamaha be liable to
you or any other person for any damages, including without limitation any incidental or consequential
damages, expenses, lost profits, lost savings or other damages arising out of the use or inability to use such
SOFTWARE even if Yamaha or an authorized dealer has been advised of the possibility of such damages, or
for any claim by any other party.
6. GENERAL
This license agreement shall be interpreted according to and governed by Japanese laws.
English
48
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installationshandbuch
SOFTWARE-LIZENZVEREINBARUNG
Die folgende Vereinbarung ist eine rechtsgültige Vereinbarung zwischen Ihnen, dem Endanwender, und der
Yamaha Corporation (“Yamaha”). Yamaha erteilt dem ursprünglichen Käufer für das beiliegende Yamaha-Soft-
wareprogramm ausschließlich zu den hier ausgeführten Bedingungen eine Lizenz zur Verwendung. Bitte lesen
Sie diese Lizenzvereinbarung sorgfältig. Durch das Öffnen dieser Packung bringen Sie zum Ausdruck, dass Sie
alle darin enthaltenen Bedingungen akzeptieren. Wenn Sie nicht mit den Bedingungen einverstanden sind, kön-
nen Sie die Packung ungeöffnet an Yamaha zurückgeben; der Kaufpreis wird in voller Höhe zurückerstattet.
Falls Sie das mitgelieferte Softwareprogramm bzw. die mitgelieferten Softwareprogramme von Yamaha als Teil
eines Softwarepakets oder im Paket mit einem Hardwareprodukt erworben haben, sind Sie nicht berechtigt, das
mitgelieferte Softwareprogramm bzw. die mitgelieferten Softwareprogramme an Yamaha zurückzugeben.
1. ERETILUNG VON LIZENZ UND COPYRIGHT
Yamaha erteilt Ihnen, dem ursprünglichen Käufer, das Recht, ein Exemplar des beiliegenden Softwarepro-
gramms und der darin enthaltenen Daten (“SOFTWARE”) als Einzelperson auf jeweils einem Computer zu
verwenden. Sie dürfen sie nicht auf mehr als einem Computer bzw. einer Computerstation verwenden. Die
SOFTWARE bleibt im Besitz von Yamaha und ist durch japanische Copyrightgesetze sowie alle anwendbaren
internationalen Vertragsbestimmungen geschützt. Sie haben ein Anspruchsrecht auf das Eigentum an den
Medien, denen die SOFTWARE beiliegt. Daher müssen Sie die SOFTWARE wie alle anderen durch Copy-
right geschützten Materialien behandeln.
2. EINSCHR
Die SOFTWARE ist durch Copyright geschützt. Sie dürfen Sie weder analysieren noch durch anderweitige
Methoden reproduzieren. Sie dürfen die SOFTWARE weder ganz noch teilweise reproduzieren, modifizieren,
verändern, gegen Entgelt oder unentgeltlich verleihen, verkaufen oder vertreiben, und Sie dürfen auf der
Grundlage der SOFTWARE keine Ableitungen erstellen. Sie dürfen die SOFTWARE nicht an andere Compu-
ter senden oder in Netzwerke einspeisen. Sie dürfen das Eigentum an der SOFTWARE und den schriftlichen
Begleitmaterialien auf unbefristeter Basis unter den Voraussetzungen übertragen, daß Sie keine Kopien
zurückbehalten und sich der Empfänger mit den Bedingungen der Lizenzvereinbarung einverstanden erklärt.
3. BEENDIGUNG
Die Lizenzbedingung des Softwareprogramms wird am Tag, an dem Sie die SOFTWARE erhalten, wirksam.
Falls ein Copyrightgesetz oder eine Bestimmung der Lizenzbedingungen verletzt wird, wird automatisch und
ohne Benachrichtigung durch Yamaha die Lizenzvereinbarung beendet. In diesem Fall müssen Sie die lizen-
sierte SOFTWARE und ihre Kopien unverzüglich vernichten.
4. PRODUKTGARANTIE
Yamaha garantiert dem ursprünglichen Käufer, daß, falls die SOFTWARE bei Verwendung unter normalen
Bedingungen nicht die in der von Yamaha bereitgestellten Anleitung beschriebenen Funktionen erfüllt, die
einzige Abhilfe darin bestehen wird, daß Yamaha auf Austauschbasis kostenlos jedes Medium ersetzen wird,
das Material- oder Verarbeitungsfehler aufweist. Abgesehen von dem oben Ausgeführten wird die SOFT-
WARE “wie die Ware liegt und steht” geliefert, und es werden keine anderen ausdrücklichen oder stillschwei-
genden Garantien hinsichtlich dieser Software übernommen, einschließlich, aber nicht beschränkt auf, die
stillschweigenden Garantien für handelsübliche Qualität und Eignung für einen bestimmten Einsatzzweck.
5. BESCHR
Ihre einzige Abhilfe und die gesamte Haftung Yamahas bestehen in dem oben Ausgeführten. Keinesfalls haftet
Yamaha Ihnen oder einer anderen Person gegenüber für etwaige Schäden, einschließlich, aber nicht
beschränkt auf, zufällige Schäden oder Folgeschäden, Kosten, Verdienstausfall, verlorene Ersparnisse oder
andere Schadenersatzansprüche, die aus der Verwendung der SOFTWARE oder aus der Tatsache hervorgehen,
daß diese SOFTWARE nicht verwendet werden konnte, selbst wenn Yamaha oder ein autorisierter Händler
über die Möglichkeit derartiger Schadenersatzansprüche informiert wurde, oder für etwaige andere Ansprüche
einer anderen Partei.
6. ALLGEMEINES
Diese Lizenzvereinbarung soll gemäß und in Übereinstimmung mit den japanischen Gesetzen ausgelegt werden.
Deutsch
49
TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Manuel d’installation
CONTRAT DE LICENCE DE LOGICIEL
Ceci est un contrat entre vous-même, l’utilisateur final, et Yamaha Corporation (« Yamaha »). Le logiciel
Yamaha ci-inclus est concédé sous licence par Yamaha à l’acheteur original et ne peut être utilisé que dans les
conditions prévues aux présentes. Veuillez lire attentivement ce contrat de licence. Le fait d’ouvrir ce coffret
indique que vous acceptez l’ensemble des termes du contrat. Si vous n’acceptez pas lesdits termes, renvoyez le
coffret non ouvert à Yamaha pour en obtenir le remboursement intégral. Si vous avez obtenu le(s)
programme(s) logiciel(s) Yamaha inclus avec un package ou fourni(s) avec un produit matériel, vous ne
pouvez pas le(s) renvoyer à Yamaha.
1. CONCESSION DE LICENCE ET DROITS D’AUTEUR
Yamaha vous concède le droit d’utiliser, en tant qu’acheteur original, un exemplaire du logiciel et des données
afférentes à celui-ci (« LOGICIEL ») sur un ordinateur pour utilisateur unique. Vous n’êtes pas autorisé à
utiliser ces éléments sur plus d’un ordinateur ou terminal d’ordinateur. Le LOGICIEL est la propriété de
Yamaha. Il est protégé par les dispositions relatives au droit d’auteur contenues dans la législation japonaise et
les traités internationaux. Vous êtes en droit de revendiquer l’appartenance du support du LOGICIEL. A ce
titre, vous devez traiter le LOGICIEL comme tout autre élément protégé par le droit d’auteur.
2. RESTRICTIONS
Le LOGICIEL est protégé par le droit d’auteur. Vous n’êtes pas autorisé à reconstituer la logique du
LOGICIEL ou à reproduire ce dernier par quelque autre moyen que ce soit. Vous n’êtes pas en droit de
reproduire, modifier, prêter, louer, revendre ou distribuer le LOGICIEL en tout ou partie, ou d’utiliser le
LOGICIEL à des fins de création dérivée. Vous n’êtes pas autorisé à transmettre le LOGICIEL à d’autres
ordinateurs ou à l’utiliser en réseau. Vous êtes en droit de céder, à titre permanent, le LOGICIEL et la
documentation imprimée qui l’accompagne, sous réserve que vous n’en conserviez aucun exemplaire et que le
bénéficiaire accepte les termes du présent contrat.
3. RESILIATION
Les conditions énoncées dans le présent contrat de licence prennent effet à compter du jour où le LOGICIEL
vous est remis. Si l’une quelconque des dispositions relatives au droit d’auteur ou des clauses du contrat ne
sont pas respectées, le contrat de licence sera résilié de plein droit par Yamaha, ce sans préavis. Dans ce cas,
vous devrez immédiatement détruire le LOGICIEL concédé sous licence ainsi que les copies réalisées.
4. GARANTIE PRODUIT
Si, dans des conditions normales d’utilisation, le LOGICIEL ne remplit pas les fonctions décrites dans le
manuel fourni, Yamaha s’engage vis-à-vis de l’acheteur original à remplacer gratuitement, sur la base d’un
échange, tout support reconnu défectueux par suite d’un défaut de matière première ou d’un vice de
fabrication. Ceci constitue le seul recours opposable à Yamaha. Hormis dans les cas expressément énoncés
plus haut, le LOGICIEL est livré « en l’état » et toute autre garantie expresse ou implicite le concernant, y
compris, de manière non limitative, toute garantie implicite de qualité marchande et d’adéquation à un usage
particulier, est exclue.
5. RESPONSABILITE LIMITEE
Votre unique recours et la seule responsabilité de Yamaha sont tels qu’énoncés précédemment. En aucun cas
Yamaha ne pourra être tenu responsable, par vous-même ou une autre personne, de quelques dommages que
ce soit, notamment et de manière non limitative, de dommages indirects, frais, pertes de bénéfices, pertes de
fonds ou d’autres dommages résultant de l’utilisation ou de l’impossibilité d’utiliser le LOGICIEL, même si
Yamaha ou un distributeur agréé ont été prévenus de l’éventualité de tels dommages, ou de quelque autre
revendication formulée par une tierce partie.
6. REMARQUE GENERALE
Le présent contrat de licence est régi par le droit japonais, à la lumière duquel il doit être interprété.
Français
This document is printed on chlorine free (ECF) paper with soy ink.
Auf Umweltpapier mit Sojatinte gedruckt.
Ce document a été imprimé sur du papier non blanchi au chlore avec de l'encre d'huile de soja.
U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
© 2004 Yamaha Corporation
409APAP1.2-01A0 Printed in Japan
WD50930

Transcripción de documentos

Installation Guide/Installationshandbuch/Manuel d’installation SPECIAL NOTICES Deutsch English • Some of the included CD-ROMs may be copy-protected. Yamaha makes no representations or warranties with regard to any problems while attempting to copy the CD-ROM(s) or software and cannot be held responsible for the results of attempts to copy the data. • The software and this Installation Guide are exclusive copyrights of Yamaha Corporation. • Use of the software and this guide is governed by the SOFTWARE LICENSING AGREEMENT which the purchaser fully agrees to upon breaking the seal of the software packaging. (Please read carefully the AGREEMENT at the end of this guide before installing the application.) • Copying of the software or reproduction of this guide in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. • Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this guide and the software. • Copying of the commercially available music data is strictly prohibited except for your personal use. • The company names and product names in this Installation Guide are the trademarks or registered trademarks of their respective companies. • Software such as the mLAN driver may be revised and updated without prior notice. Make sure to check and download the latest version of the software from the following site. http://www.yamahasynth.com/down/index.htm • Future upgrades of application and system software and any changes in specifications and functions will be announced separately. Français BESONDERE HINWEISE • Einige der mitgelieferten CD-ROMs sind möglicherweise kopiergeschützt. Yamaha gibt bei Problemen im Zusammenhang mit dem Versuch, die CD-ROM oder die Software zu kopieren, keine Zusicherungen oder Gewährleistungen und kann für die Folgen des Kopierens der CD-ROM oder der Software nicht verantwortlich gemacht werden. • Dieses Programm und diese Installationsanleitung sind im Sinne des Urheberrechts alleiniges Eigentum der Yamaha Corporation. • Die Benutzung des Programms und dieser Anleitung unterliegt der SOFTWARELIZENZVEREINBARUNG, mit der sich der Erwerber durch Öffnen des Siegels der Programmverpackung uneingeschränkt einverstanden erklärt. (Bitte lesen Sie die VEREINBARUNG am Ende dieser Anleitung vor Installation der Anwendung sorgfältig durch.) TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide/Installationshandbuch/Manuel d’installation 1 Français Deutsch English • Das Kopieren der Software und die Reproduktion dieser Anleitung, in welcher Form auch immer, in Teilen oder als Ganzes, sind nur mit schriftlicher Genehmigung des Herstellers erlaubt und sonst ausdrücklich verboten. • Yamaha leistet keinerlei Garantie hinsichtlich der Benutzung des Programms und der zugehörigen Dokumentation und übernimmt keine Verantwortung für die Ergebnisse der Benutzung dieser Anleitung oder des Programms. • Das Kopieren im Handel erhältlicher Musikdaten ist nur für Ihren Privatgebrauch zulässig und sonst streng untersagt. • Die in dieser Installationsanleitung erwähnten Firmen- und Produktnamen sind Warenzeichen bzw. eingetragene Warenzeichen der betreffenden Firmen. • Software wie z.B. der mLAN Driver kann ohne vorherige Benachrichtigung überarbeitet und aktualisiert werden. Achten Sie darauf, auf der folgenden Website nach der neuesten Version der Software zu suchen und sie herunterzuladen. http://www.yamahasynth.com/down/index.htm • Zukünftige Aktualisierungen von Anwendungs- und Systemsoftware sowie jede Änderung der technischen Daten und Funktionen werden separat bekanntgegeben. REMARQUES PARTICULIERES • Certains des CD-ROM inclus peuvent être protégés contre la copie. Yamaha n’offre aucune garantie quant aux problèmes pouvant surgir lors de la copie du CD-ROM ou du logiciel et ne peut être tenu responsable du résultat de la copie du CD-ROM ou du logiciel. • Les droits d’auteurs (copyright) de ce logiciel et de ce manuel d’installation appartiennent exclusivement à Yamaha Corporation. • L’usage de ce logiciel et de ce manuel est défini par l’accord de licence auquel l’acheteur déclare souscrire sans réserve lorsqu’il ouvre le sceau de l’emballage du logiciel. (Veuillez donc lire attentivement l’accord de licence du logiciel situé à la fin de ce manuel avant d’installer le logiciel.) • Toute copie du logiciel et toute reproduction totale ou partielle de ce manuel, par quel moyen que ce soit, est expressément interdite sans l’autorisation écrite du fabricant. • Yamaha n’offre aucune garantie en ce qui concerne l’utilisation du logiciel et de la documentation. Yamaha ne peut en aucun cas être tenu responsable des dommages éventuels résultant de l’utilisation de ce manuel et de ce logiciel. • Toute copie de données musicales commercialisées est formellement interdite, sauf pour usage personnel. • Les noms des firmes et des produits apparaissant dans ce manuel d’installation sont des marques commerciales ou des marques déposées appartenant à leurs détenteurs respectifs. • Les logiciels tels que le pilote mLAN sont susceptibles d’être révisés et mis à jour sans avertissement préalable. Veuillez toujours à vérifier la version du logiciel utilisée et à télécharger la dernière version en date sur le site suivant : http://www.yamahasynth.com/down/index.htm • Les remises à jour du programme et du système ainsi que toute modification des caractéristiques et fonctions seront annoncées séparément. 2 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide/Installationshandbuch/Manuel d’installation Contents Important Notices about the CD-ROM.............................................4 Operating System (OS) ..........................................................................4 CD-ROM Installation Procedure .............................................................4 For Windows Users...........................................................................5 CD-ROM Contents..................................................................................5 System Requirements for i88X/mLAN16E/MY16-mLAN Software.........6 Software Installation ...............................................................................8 Connecting a Computer to an mLAN device via mLAN........................19 Installing the Plug-in Effect (For i88X Users)........................................26 For Mac OS 9 Users (i88X and mLAN16E only)............................28 English CD-ROM Contents................................................................................28 System Requirements for i88X/mLAN16E Software ............................30 Software Installation .............................................................................31 Connecting a Computer to an mLAN device via mLAN........................36 Plug-in Effect ........................................................................................41 For Mac OS X Users ........................................................................42 Display Messages ...........................................................................43 Troubleshooting ..............................................................................44 Noise may be generated during the following operations. Before performing these operations, lower the output level of each device. • Turning the power to the computer and mLAN devices on or off • Connecting or disconnecting an IEEE1394 (mLAN) cable • Making an mLAN connection in mLAN Auto Connector • Changing the wordclock master and slave status in mLAN Auto Connector or mLAN Graphic Patchbay • Selecting On or Off in mLAN Manager (Windows) • Starting or quitting the OS • Installing/uninstalling mLAN software For Windows users • Do not turn on the power to the mLAN devices during installation until the computer displays the following message. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 3 Important Notices about the CD-ROM Operating System (OS) The data content and installation procedure is different for Windows and Macintosh. Please read the section that applies to your operating system. ● i88X/mLAN16E users: ● MY16-mLAN users: The CD-ROM contains software for Windows and Mac OS 9. Windows ➝ please read from page 5. Mac OS 9 ➝ please read from page 28. The CD-ROM contains software for Windows. Software for Macintosh is not included. Windows ➝ please read from page 5. English Regarding Mac OS X support, refer to page 42. CD-ROM Installation Procedure Before breaking the seal on the software packaging, please read carefully the Software Licensing Agreement at the end of this guide. 1 Verify that your system meets the operating requirements of the software (mLAN Tools, driver, etc.). Windows: page 6; Mac OS 9: page 30 2 Install the appropriate driver on your computer, and make the necessary settings. Windows: page 9; Mac OS 9: page 31 3 i88X Users: Install the Plug-in Effect. For subsequent operations, refer to the owner’s manual for each software program (online help/ PDF manual). • To view PDF files, you must install Adobe Reader on your computer. If you do not have Adobe Reader, you can download the application from the Adobe website at the following URL: http://www.adobe.com Windows: page 5; Mac OS 9: page 28 4 Start up the software. Most of the computer display examples in this guide are taken from the English version OS/ software. Quick solutions/Reference materials • Setting the sampling frequency ........................................................................... page 19, 36 • Determining the number of mLAN audio channels. ............................................. page 19, 36 • Changing the settings of the mLAN Driver........................................................... page 15, 34 • Determining the latency ............................................................................................. page 15 • How can I delete or re-install the driver?........................................................ pages 8, 25, 33 • Connecting multiple mLAN devices..................................................................... page 19, 36 4 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide For Windows Users CD-ROM Contents Software for Windows is included on CD-ROM(s). (i88X users should begin by installing TOOLS for i88X/mLAN16E.) ● TOOLS for i88X/mLAN16E ● TOOLS for MY16-mLAN mLAN_ Application Name mLAN Applications for YAMAHA mLAN Tools Contents This software includes mLAN drivers and applications required to make mLAN connections between the mLAN devices and the computer. Install the software while the power to the mLAN devices is off (page 9). A single installation procedure installs all applications necessary for mLAN communications. Software to be installed includes mLAN Auto Connector and mLAN Graphic Patchbay, which are used to set up audio and MIDI connections for an mLAN network. ● Plug-in Effect (included only with i88X) • This software can be used as plug-in software within a VST compatible program. • To call up the PDF manual for each program, select [Start] ➝ [All programs] ➝ [YAMAHA VST Plugins] ➝ (the relevant software) ➝ [Online Manual]. • For instructions on installing the Plug-in Effects, see page 26. Folder Name VST_ Application Name Contents 01X Channel Module*1 This software reproduces the EQ and Dynamics effects built into each channel of the YAMAHA Digital Mixing Studio 01X, and uses the processing power of the computer for the effects. You can use the Dynamics and 4-band EQ functions (that can be also found on Yamaha Digital Mixing consoles) as effects software. You can also import the 01X settings, thus reproducing the songs created on the 01X. Pitch Fix*1 This program is used to edit the pitch of recorded vocals. More than just a pitch processor, it can also be used to change the character of the vocals. Moreover, you can use MIDI data on the host application to control the Pitch Fix effect. For more information on setting up with the host application, refer to the Pitch Fix PDF owner’s manual. Vocal Rack*1 This is a multi-effect program for processing vocals. The plug-in features various effects, including a high-pass filter, compressor and a 3-band equalizer. Final Master*1 This is a multi-effect program for mastering purposes. It features a compressor, limiter and soft-clip function, and allows you to split the signal into three bands for separate multi-band processing. *1 These applications are supplied with online/PDF manuals. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 5 English Folder Name ■ About Open Plug-in Technology You can start mLAN Graphic Patchbay as either stand-alone software or as a plug-in for an Open Plugin Technology compatible application. Open Plug-in Technology (OPT) is a new software format that enables you to control MIDI devices from a music software sequencer. For example, OPT enables you to start and operate various parts of your music system, such as Plug-in Board editors and mixing control editors, directly from an OPT-compatible sequencer. OPT also makes it unnecessary to set MIDI drivers for each application, streamlining your music production system and making all operations more convenient and seamless. About OPT Levels The client application and its compatibility with OPT can be divided into three levels, as shown below. Level 1 (OPT Panels) provides basic support for opening and displaying OPT control panels that can transmit data via a clients’ external MIDI connectors. Typically, this enables basic hardware editor control panels to operate properly. English Level 2 (OPT Processors) provides support for real-time MIDI processors and panel automation. Typically, this enables both real-time and offline MIDI effects (e.g., arpeggiators, transposers, etc.) to operate properly and supply automation to OPT panels. Level 3 (OPT Views) provides support for edit views and MIDI processors and panels that require direct access to client sequencer storage structures. Typically, this enables support of sophisticated MIDI edit views (e.g., list editors, auto accompaniment, data checkers, etc.). OPT Level Implementation for the mLAN Graphic Patchbay This chart shows the OPT-compatibility of mLAN Graphic Patchbay. mLAN Graphic Patchbay operation OPT levels of the client application Operation support Operation limits VIEWS (Level 3) Yes None PROCESSORS (Level 2) Yes None Yes (with limitations) None PANELS (Level 1) All mLAN Graphic Patchbay functions work under the client applications of any OPT level (Panels (Level 1), Processors (Level 2), and Views (Level 3)). • Certain operations may not work as expected if there is no corresponding function in the client application (sequencer, etc.). The highest level of implementation for the client application is indicated in the OPT logo (which appears along with the version information in the application). System Requirements for i88X/mLAN16E/MY16-mLAN Software The system requirements below are necessary for using the included software. • The system requirements below may differ slightly depending on the particular operating system. • The minimum requirements for included software not listed below may differ. For details, refer to the relevant online manual or documentation of the software. • For details on minimum requirements for each DAW (Digital Audio Workstation) software, refer to the respective owner’s manual. 6 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide These are the total system requirements, including the audio sequencer, mLAN software and the plug-in effects. OS : Windows XP Professional/XP Home Edition Computer : Intel Pentium or Celeron family processor, with the S400 (400 Mbps) IEEE1394 (FireWire) or i.Link terminal (*1). Hard Disk : Free disk space of 250 MB (i88X)/ 50 MB (mLAN16E, MY16-mLAN) or more; high-speed hard disk ● Recommended system (*2) • Connecting a single mLAN device to a computer peer-to-peer: Computer : 2.2 GHz or higher; Intel Pentium 4 processor Available Memory : 512 MB or more • Connecting a computer and three mLAN devices in an mLAN network: Computer : 2.6 GHz or higher; Intel Pentium 4 processor Available Memory : 512 MB or more ● Minimum system requirements (*2) Computer : Intel Pentium 1.2 GHz or Intel Celeron 1.7 GHz (or higher) Available Memory : 384 MB or more *1 The computer must have an IEEE 1394 (FireWire) or i.Link terminal. If there is no terminal, install an IEEE 1394 interface card (PCI or PC). For more details on system requirements and recommended PCI or PC cards, see http://www.yamahasynth.com *2 The system requirements listed here apply when using the included software and when playing audio/MIDI data detailed below on standard sequencer software. This may differ depending the particular sequencer software you are using. Recommended system requirements (Connecting a single mLAN device to a computer peer-to-peer) Fs=44.1kHz/24-bit Audio Driver 18In/18Out (i88X) 16In/8Out (mLAN16E) 16In/16Out (MY16-mLAN) MIDI Driver 1In/1Out (i88X, MY16-mLAN) 3In/3Out (mLAN16E) 16 MIDI and 12 Audio playback tracks 2 Audio recording tracks 2 Sends for Plug-in Soft Effect 10 Inserts for Plug-in Soft Effect 2 Channels for Plug-in Soft Synthesizer Latency of 5msec or less Recommended system requirements (Connecting a computer and three mLAN devices) Fs=44.1kHz/24-bit Audio Driver 32In/32Out (total) MIDI Driver 4In/5Out (total) 16 MIDI and 8 Audio playback tracks 2 Audio recording tracks 2 Sends for Plug-in Soft Effect 10 Inserts for Plug-in Soft Effect 2 Channels for Plug-in Soft Synthesizer Latency of 5msec or less Minimum system requirements Fs=44.1kHz/16bit Audio Driver 8In/2Out (i88X) 2In/2Out (mLAN16E, MY16-mLAN) MIDI Driver 1In/1Out (i88X, MY16-mLAN) 2In/2Out (mLAN16E) 16 MIDI and 12 Audio playback tracks 2 Sends for Plug-in Soft Effect 6 Inserts for Plug-in Soft Effect No Plug-in Soft Synthesizer Latency of about 50msec • Up to two PCI or PC cards can be used. However, you can use only one card at a time. If you are using an IEEE1394 interface built into the computer, you can use only one IEEE1394 PCI or PC interface card. • When using a laptop or notebook computer, a builtin IEEE 1394 terminal may not be available. If this is the case, install an appropriate PC interface card. ● Plug-in Effect (included only with i88X) OS : Windows XP Professional/XP Home Edition/2000/Me/n98SE/98 To use mLAN, turn mLAN on each time you start the computer by using the mLAN icon (mLAN Manager) in the task bar (page 14). TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 7 English ● i88X/mLAN16E/MY16-mLAN (mLAN Tools 2.0/mLAN Applications for YAMAHA) Software Installation For instructions on how to install the software other than one referred to below, see page 5 in the section “CD-ROM Contents.” Uninstall (removing the installed application) You can remove the installed application software.Select [START] (➝ [Settings]) ➝ [Control Panel] ➝ [Add/Remove Programs] ➝ [Install/Uninstall], then select the application to be removed and click [Add/ Remove...]. Follow the on-screen instructions to uninstall the application. • The button names or menus may differ depending on the computer OS. • In order to uninstall the mLAN software, the following two items must be deleted. Delete them in order, 1 then 2. English 1. mLAN Applications for YAMAHA 2. mLAN Tools 2.0 For information on uninstalling the plug-in effect, see page 27. Check beforehand the drive name (D:, E:, etc.) corresponding to the CD-ROM you are using. The drive name is indicated under the CD-ROM icon of [My computer]. (The root directory of the CD-ROM driver is indicated as D:\, E:\, etc.) 8 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide mLAN Tools 2.0 and mLAN Applications for YAMAHA mLAN Tools 2.0 software includes a driver that enables you to connect mLAN devices to a computer. mLAN Applications for YAMAHA enables audio and MIDI signals to be transferred between a computer and mLAN devices via mLAN cables. This software enables you to connect the i88X, mLAN16E, MY16-mLAN, or 01X to a computer via mLAN. 01X users should uninstall the older version of the mLAN software before installing this software. (Refer to the 01X Installation Guide.) Follow the steps below to install these software applications. • For explanations on error messages, see page 43. 1 Disconnect all MIDI cables that connect MIDI devices to MIDI IN/OUT connectors on the mLAN device. 2 Using an IEEE1394 (FireWire/iLink) cable, 5 Select [Start] ➝ [Control Panel]. If the control panel appears as shown below, click “Switch to Classic View” in the upper left of the window.All control panels and icons will be displayed. connect the mLAN device directly to the computer (without using a hub), and disconnect all other IEEE 1394-connected devices from the computer. 3 Make sure that the power to the mLAN device is turned off. 4 Start the computer and log in to the Administrator account. • If you are using the S200 data transfer rate standard (check the rear panel of your particular device, or refer to the specifications in the owner’s manual), make sure to uninstall the old version of mLAN Tools beforehand. For more information on uninstalling the software, refer to the owner’s manual for the corresponding device. Proceed to the next step. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 9 English Preparing to install 6 Go to [System] ➝ [Hardware] ➝ [Driver Signing] ➝ [File Signature Verification], and check the radio English button to the left of “Ignore -Install all files, regardless of file signature” and click [OK]. • After completing the installation, make sure to restore the original setting if necessary. 7 Check that no “!” or “x” marks appear next to “IEEE 1394 Bus host controllers” (in [System] ➝ [Hard- ware] ➝ [Device Manager]). If one of these marks is shown, the mLAN (IEEE 1394/i.Link) connection cannot be used. Refer to the owner’s manual of your computer for details. 10 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide dow, then click the Close button ([X]) at the top right of the window to close the Control Panel. 9 Exit from any open applications and close all open windows. 10 Insert the included CD-ROM into the CDROM drive. Starting up the Installer for the mLAN Software The installer will install the following two programs to your computer. • mLAN Tools 2.0 • mLAN Application for YAMAHA Installation of mLAN Tools 14 Click [Next]. The display for installing mLAN Tools appears. 15 Click [Next]. The “Destination Directory” window appears, letting you determine the desired drive and folder name for installing mLAN Tools. The destination directory is automatically set; however, if you wish to change it, click the [Browse…] button and select the desired folder (drive:\folder name). Click [Next] after making or confirming the selection. • In general, there is no need to change the destination directory. 16 Confirm the drive and folder name and click [Next] to start installation. • Use the Cancel button or Close button to quit the installation. Quitting by using the [CTR]+[ALT]+[DEL] buttons or by turning off the power while installation is in process is can result in problems since the installation is terminated without performing a proper uninstall. 11 Double-click on the “mLAN_” folder. Various files are shown, including “Setup.exe.” • To cancel the installation, click [Cancel]. 17 When installation is finished, a “Completed” message appears. Click [Finish]. Proceed to the next step. 12 Double-click on “Setup.exe.” 13 A series of confirmation messages appear. If there are no problems, click [OK] in each message. When finished, a “Welcome” display appears. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 11 English 8 Click [OK] to close the System Properties win- Installation of mLAN Applications for YAMAHA (mLAN Software) When the mLAN Tools 2.0 installation is complete, the computer automatically displays a window that enables you to start the installation of Applications for YAMAHA. Click [Next]. 18 Determine the desired destination drive and English folder name for installation in the “Destination Directory” window. The destination directory is automatically set; however, if you wish to change it, click the [Browse…] button and select the desired folder (drive:\folder name). mLAN Driver initial settings After you restart the computer, complete the mLAN driver initial settings. Select [ON] in mLAN Manager to activate the mLAN driver (page 14). 21 A dialog box prompts you to turn on the power to the mLAN device. Connect the mLAN device to the computer, then turn on the power to the i88X, mLAN16E, or MY16mLAN (or 01X). 22 Installing the mLAN device The “Found New Hardware Wizard” window is displayed. Check the radio button next to “Install the software automatically [Recommended],” then click [Next]. • To cancel the installation, click [Cancel]. 19 Confirm the drive and folder name and click [Next] to start installation. • To cancel the installation, click [Cancel]. 20 When the installation process is complete, a message will prompt you to restart the computer. Click [Next]. • Depending on the version of Windows you are using, the “Found New Hardware Wizard” may display a screen asking you whether you want to find the appropriate software by connecting to Windows Update. In this screen, choose the radio button next to the selection indicating that you don’t want to connect to Windows Update, and then click [Next]. Even if such a screen should appear subsequently in this procedure, choose the radio button indicating that you don’t want to connect, and then click [Next]. When canceling the installation If you’ve cancelled an installation before it is complete, the software may not have been installed properly. Follow the instructions below to properly install the software. 1 Click on “Add or Remove Programs” in the Control Panel (page 8) and find “mLAN Applications for YAMAHA” and “mLAN Tools 2.0” in the list. 2 Delete the two programs in order: first, “mLAN Applications for YAMAHA,” then “mLAN Tools 2.0.” 3 Start installation again from step 12 (page 11). 12 23 After you finish installing the connected mLAN device, click [OK] in the dialog box that appeared in Step 21. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 24 The “Make the driver initial settings” dialog mLAN MIDI Port initial settings box is displayed. Click [OK]. 28 The computer automatically displays the • During Steps 25 and 26, and Steps 28 and 29, the computer displays a window indicating that you are now making the initial settings for each driver. This window also indicates the number of times the “Found New Hardware Wizard” will be displayed during the procedure. Unless you wish to cancel installation, do not close this window. “Found New Hardware Wizard.” Check the radio button next to “Install the software automatically [Recommended],” then click [Next]. mLAN Network initial settings 25 The computer automatically displays the “Found New Hardware Wizard.” Check the radio button next to “Install the software automatically [Recommended],” then click [Next]. English Example: 29 When the installation is complete, the computer displays a message of indicating that installation is complete. Click [Finish]. 30 Repeat Steps 28 and 29 until the window (indicating that you are making the mLAN Stream driver initial settings) closes. 31 The computer displays a message indicating that the initial settings for mLAN driver are complete. Click [OK]. To use an audio sequencer via mLAN, you must connect the computer to the mLAN device using mLAN audio Connector or Graphic Patchbay (page 19). 26 When the installation is complete, the computer displays a message indicating that installation is complete. Click [Finish]. 27 Repeat Steps 25 and 26 until the window (indicating that you are making the mLAN Bus driver initial settings) closes. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 13 Confirming the installation Task bar (mLAN Manager) If the installation is successful, an mLAN icon (mLAN Manager) is added to the task bar. To call up the menu, right-click on the icon. When using mLAN, right click on the mLAN icon (mLAN Manager) in the task bar and select “ON” (start mLAN). • To use mLAN connections, after you start the computer, right-click the mLAN icon (mLAN Manager) in the Task bar, then select [ON] to activate mLAN connections. • You can use the mLAN Driver Setup (page 15) to check whether data is being properly transmitted and received via mLAN. When starting up the mLAN English The message below appears when mLAN is being started. ON.................... Enables mLAN operation for data transfer (Run the “mLAN Start application”). OFF.................. Disables mLAN operation (Run the “mLAN Stop” application). You can lessen the CPU load by not using mLAN. Driver Setup ... Starts mLAN Driver Setup (page 15). Auto Connector ....... Starts mLAN Auto Connector (page 19). Graphic Patchbay ... Starts mLAN Graphic Patchbay. For more information, refer to the mLAN Graphic Patchbay Online Manual. EXIT................ This deletes the mLAN icon from the task bar, maintaining the current mLAN ON/OFF status. To display it again, select [Start] ➝ [(All) Programs] ➝ [Startup] ➝ [mLAN Manager]. 14 To cancel mLAN startup, click [Cancel] in the mLAN Start window. To use mLAN, right-click on the mLAN icon (mLAN Manager) in the task bar, and select [ON]. Device Manager (Operating System) 1 Select [Control Panel] from the Start menu. 2 Double-click on the System icon to call up the System Properties window. 3 Select the Hardware tab and click [Device Manager]. 4 Click the [+] symbol located at the left of “Sound, video and game controllers,” and verify that “YAMAHA i88X,” “YAMAHA mLAN16E,” or “YAMAHA MY16-mLAN” etc. is shown. Also verify that “YAMAHA mLanBus” is shown. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide Changing settings after installation The mLAN-related settings can be changed after installation from the mLAN Driver Setup window. mLAN Driver Setup (Right-click the mLAN icon in the task bar ➝ DriverSetup) This window lets you check and change the mLAN settings for receiving/transmitting data. Make sure to close any application (DAW, etc.) using the mLAN connection before making changes. • To change the wordclock (sample rate) and the number of channels used, right-click on the mLAN icon in the task bar and start the mLAN Auto Connector and Graphic Patchbay. q English w e y t r q 1394 Adapter Card ID This indicates the particular ID of the IEEE 1394 (FireWire/iLink) interface card installed to the computer. When several cards are installed, this is used to select the desired card. Cards not recognized by the mLAN driver are not displayed. • The correct name of the manufacturer or vendor may not be displayed depending on the particular card you are using. w Required CPU Determines the computer’s required processing power (the amount of processing load applied to the computer by the mLAN driver). You can also control the processing load by adjusting the latency in “ASIO mLAN Control Panel.” (see below) Latency and Required CPU A particular computer configuration (i.e., processing speed and system memory size) may affect the computer’s ability to properly record and play back audio data in your audio sequencer, resulting in noise or other audio problems. In most cases, you can solve these problems by adjusting the latency (delay time). (See “Latency of mLAN” on page 16.) TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 15 #mLAN InstallGuide_E2.fm Page 16 Monday, October 4, 2004 11:53 AM However depending on the performance of your computer and on how it is being used (i.e., whether other applications are being used simultaneously, or whether multiple mLAN devices are connected, etc.), you may still experience noise or sound interruption even after increasing the latency. In this case, change the “Required CPU” setting to “Medium Performance” or “Low Performance” to lighten the processing load on your computer, and then adjust the latency (the Preferred Buffer Size setting below) once again. • Lower latency values result in shorter delay times and work better for real-time recording and playback. • Higher latency values result in longer delay times, but allow for use of more audio channels and plug-in effects (thus reducing the computer’s momentary processing load). Conversely, if you experience no noise or interruptions even with the “Preferred Buffer Size” setting described below set to the minimum, you can minimize the overall latency by setting Required CPU to “High Performance” and then adjusting the latency once again. ● Latency of mLAN Audio latency (msec) English Audio latency is determined by the “Preferred Buffer Size” setting in the “ASIO mLAN Control Panel.” The audio latency value is shown in the “ASIO mLAN Control Panel” (see below). MIDI latency (msec) The MIDI latency value varies with the mLAN driver version. For information on the MIDI latency of your mLAN driver version, refer to the “MIDI_Latency.txt” file, which you can access by selecting [Program files | mLAN Tools | YAMAHA]. ● ASIO mLAN Control Panel When you start the ASIO mLAN Control Panel, the system displays the following dialog box. When using the mLAN ASIO Driver, open the ASIO Control Panel within the driver settings of the DAW software (the particular menu depends on the software you are using) and set the Preferred Buffer Size as needed. • Also, when using the mLAN WDM driver, adjust as necessary the latency value of the WDM driver (which corresponds to the latency of the ASIO driver in this chart) within the driver settings of the DAW software. • The initial setting of the Preferred Buffer Size of the mLAN ASIO driver is the smallest value. q Preferred Buffer Size This parameter enables you to specify the size of the buffer inside the mLAN ASIO driver. w Sample Size This parameter enables you to specify the bit resolution for audio data transmission and reception. e Latency This field indicates the audio latency value for transmission and reception. Audio latency is determined by the “Preferred Buffer Size (w)” setting. q w e r r OK Click to enable the settings and close the dialog box. t Cancel Click to close the dialog box without changing the settings. 16 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide t e Status If you are using mLAN Auto Connector, this parameter indicates the current data (MIDI/ Audio) reception status (from the mLAN device to computer) of the mLAN connection. If there is an error in transmission, the computer displays an error message. If you are using mLAN Graphic Patchbay, refer to the Graphic Patchbay Online Manual for information on the error messages. Blue ....... Data is being properly transmitted. Yellow ... Only one type of data (MIDI or audio) is being received. Red ........ Error in reception. Gray....... No reception. About the Information window This window indicates the MIDI and audio data reception status (from the mLAN device to computer). Icon Blue ........ Reception is normal. Red......... Error in reception. Gray........ No reception. English R1, R2, etc. This indicates the data reception status. “R1” corresponds to MIDI reception while “R2 corresponds to audio reception from the mLAN device. The number of tabs shown differs depending on your particular computer configuration. Receive Status This mark indicates the order in which the data of each format is received. The symbol “o” indicates that data in the corresponding format is being received. The symbol “-” indicates that data in a different format is being received. For example, the symbol “oooooooo-” in the “Audio” field indicates that nine sequences have been received, and the first eight sequences are in the audio data format. The “Unknown” field displays symbols if sequences in unknown formats are received. These fields are blank if no mLAN data is received. If an error occurs during reception, a red warning message flashes. In this case, check the transmission device. r Set y EXIT Clicking this button actually applies the settings made in this window. Changes to the settings do not take effect unless [Set] is clicked. Click to close the dialog box. t Revert If you’ve made changes to the settings (but not yet clicked [Set]), clicking this button restores the settings made the last time [Set] was clicked. Once you click [Set], [Revert] cannot be used. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 17 If the computer’s system sound is output to mLAN audio channels: The computer’s system sound (such as an alarm sound) will be output to mLAN audio channels if the following settings are made: • The WDM driver is selected in mLAN Auto Connector or mLAN Graphic Patchbay. • mLAN WDM driver (mLAN Audio Out/In 01) has been selected for the Windows system audio device. Follow the steps below to prevent the system sound from being output to mLAN audio channels. • The following setting cancels output of all Wave sounds from the computer speakers. 1 Select [Start] ➝ [Control Panel] ➝ [Sounds and Audio Devices] ➝ [Voice], and click [Volume…] in English the “Voice playback” section to call up the Master Volume window. 2 Check the Mute checkbox in the Wave column. 18 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide Connecting a Computer to an mLAN device via mLAN This section describes the procedure for connecting a computer to a single mLAN device peer-to-peer in mLAN Auto Connector. In mLAN Auto Connector, you can easily connect an mLAN device by setting up the wordclock and the number of audio I/O channels. To connect multiple mLAN devices to a computer, use mLAN Graphic Patchbay. For more information on mLAN Graphic Patchbay, refer to the mLAN Graphic Patchbay Online Manual. • If you use Auto Connector after you make connections in mLAN Graphic Patchbay, the connections made in mLAN Graphic Patchbay will be cancelled. • You can also use mLAN Graphic Patchbay to connect a computer to a single mLAN device peer-to-peer. • The mLAN Auto Connector windows may appear different when certain mLAN devices are connected. 1 Connect a computer to an mLAN device using an IEEE1394 cable. 2 Right-click the YAMAHA mLAN Manager icon Noise may be generated during the following operations. Before performing these operations, lower the output level of each device. • Turning the power to the computer and mLAN devices on or off • Connecting or disconnecting an IEEE1394 (mLAN) cable • Making an mLAN connection in mLAN Auto Connector • Changing the wordclock master and slave status in mLAN Auto Connector or mLAN Graphic Patchbay • Selecting On or Off in mLAN Manager (Windows) • Starting or quitting the OS • Installing/uninstalling mLAN software 3 Set up the wordclock and specify the number of audio channels (see below), then click the [Connect] button. The computer and mLAN device are connected via mLAN. Connecting the i88X q e w r t y u i o !0 !1 !2 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 19 English in the Task bar, then select [Auto Connector]. q Nickname i [ASIO/WDM] button This field indicates the nickname of the connected i88X. To change the nickname, refer to “Node Information” in the mLAN Graphic Patchbay Online Manual. Select the ASIO or WDM driver as appropriate for your environment. w Model Name This parameter enables you to select an mLAN device to which you wish to make an mLAN connection in a multiple mLAN device network. English e [Update] button Clicking this button updates the information on the mLAN devices connected to the mLAN network. Use this button when you add an mLAN device to the network while mLAN Auto Connector is running. r [Identify] button Clicking this button causes the i88X ACTIVE indicator to flash for a few seconds. t Sample Rate This parameter enables you to specify the sampling frequency (wordclock frequency). y Wordclock Master radio buttons These buttons enable you to specify the computer or i88X as the wordclock master. u PC → i88X This parameter enables you to specify the number of channels of audio data routed from the computer’s audio output (mLAN driver’s audio output) into the i88X. Signals input in the i88X are output from the i88X’s OUTPUT 1-8 jacks (analog), DIGITAL STEREO COAXIAL or OPTICAL OUT jack (digital), or ADAT OUT jack (ADAT). 20 • With analog connections, WDM will use the last two of the selected ASIO channels. The WDM channel signals will be output from OUTPUT 7 and 8. o PC ← i88X This parameter enables you to specify the number of channels for audio data that is input at the i88X’s INPUT 1-8 jacks (analog), DIGITAL STEREO COAXIAL or OPTICAL IN jack (digital), or ADAT IN jack (ADAT) and output to the computer. !0 [Connect] button Click this button to connect the i88X to the computer via mLAN. When the connection is completed, the mLAN Auto Connector window will close automatically. !1 [Cancel] button Click this button to cancel the settings and close mLAN Auto Connector. !2 [Setup] button Click this button to open the i88X Control Panel window, which enables you to set the wordclock transition speed. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide Connecting the mLAN16E (MOTIF ES) q e w r t y u i English o !0 !1 !2 q Nickname t Sample Rate This field indicates the nickname of the connected mLAN16E. To change the nickname, refer to “Node Information” in the mLAN Graphic Patchbay Online Manual. This parameter enables you to specify the sampling frequency (wordclock frequency). w Model Name This parameter enables you to select an mLAN device to which you wish to make an mLAN connection in a multiple mLAN device network. When the mLAN16E is connected, select the name of the device equipped with an mLAN16E. e [Update] button Clicking this button updates the information on the mLAN devices connected to the mLAN network. Use this button when you add an mLAN device to the network while mLAN Auto Connector is running. r [Identify] button Clicking this button causes the mLAN16E ACTIVE indicator to flash for a few seconds. y Wordclock Master radio buttons These buttons enable you to specify the computer or mLAN16E as the wordclock master. u PC → MOTIF ES This parameter enables you to specify the number of channels of audio data input into the mLAN16E from the computer’s audio output (mLAN driver’s audio output). i [ASIO/WDM] button Select the ASIO or WDM driver as appropriate for your environment. • With the MOTIF ES, WDM will use the last two of the ASIO channels selected via “mLAN INPUT.” The WDM channel signals will be routed to the MOTIF ES as “mLAN IN 7/8CH.” TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 21 o PC ← MOTIF ES !0 [Connect] button This parameter enables you to specify the number of channels of audio data input into the computer from the mLAN16E’s output. Click this button to connect the mLAN16E to the computer via mLAN. When the connection is completed, the mLAN Auto Connector window will close automatically. • The number of audio transmission channels and MIDI ports varies on different mLAN16E-compatible devices. !1 [Cancel] button Click this button to cancel the settings and close mLAN Auto Connector. • For more information on audio and MIDI connections for a MOTIF ES with an mLAN16E installed, refer to “System Examples” in the mLAN16E Owner’s Manual. !2 [Setup] button English Click this button to open the mLAN16E Control Panel window, which enables you to set the wordclock transition speed. Connecting the MY16-mLAN q e w r t y u i o q Nickname This field indicates the nickname of the connected MY16-mLAN. To change the nickname, refer to “Node Information” in the mLAN Graphic Patchbay Online Manual. 22 !0 !1 w Model Name e [Update] button These are the same functions as for the i88X or mLAN16E (page 20). TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide r [Identify] button i PC ← MY16-mLAN Clicking this button causes the MY16-mLAN ACTIVE indicator to flash for a few seconds. This parameter enables you to specify the number of channels of audio data routed from the MY16-mLAN’s output into the computer’s input. t Sample Rate This parameter enables you to specify the sampling frequency (wordclock frequency). y Wordclock Master radio buttons These buttons enable you to specify the computer or MY16-mLAN as the wordclock master. o [Connect] button !0 [Cancel] button !1 [Setup] button These are the same functions as for the i88X or mLAN16E (page 20). This parameter enables you to specify the number of channels of audio data routed from the computer’s audio output (mLAN driver’s audio output) into the MY16-mLAN. Setting the wordclock transition speed (in the mLAN Control Panel) When you click the [Setup] button in the Node Information window in mLAN Auto Connector or mLAN Graphic Patchbay, the mLAN Control Panel opens. This panel enables you to set the wordclock transition speed. The Wordclock Transition Speed parameter enables you to specify how fast the initial wordclock setting will change to a new setting if the mLAN device is operating as a slave in an mLAN network. Slow: Usually, select this option. Fast: Select this option if the wordclock master device is referencing timecode, such as MTC, thus changing the wordclock setting. 4 Click the [Connect] button. When the mLAN device is connected correctly, mLAN Auto Connector closes and mLAN communications begin. • If connection fails, right-click the mLAN icon in the Task bar, restart mLAN Auto Connector, then click the [Connect] button again. You do not need to restart the computer. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 23 English u PC → MY16-mLAN Hints when using audio data (Windows) For optimum use of the audio functions, we recommend you make the following settings. These settings minimize possible audio problems, such as drop outs, glitches and noise. • Set the DMA mode (high-speed transfer mode) of the hard disk to on To set the DMA mode, select [Control Panel] ➝ [System] (➝ [Hardware]) ➝ [Device Manager], then change the setting from [Disk drives] or [Hard disk controllers]. • Set Processor Scheduling to “Background services” Select [Control Panel] ➝ [System] ➝ [Advanced] ➝ [Performance] ➝ [Settings] ➝ [Advanced] and check (enable) “Background services” in the “Processor scheduling” section. • Set the Visual Effects options to “best performance” Select [Control Panel] ➝ [System] ➝ [Advanced] ➝ [Performance] ➝ [Settings] ➝ [Visual Effects] and check (enable) “Adjust for best performance.” English • Turn Automatic Updates off Select [Control Panel] ➝ [System] ➝ [Automatic Updates] and un-check (disable) “Keep my computer up to date.” • Set Remote Assistance to off Select [Control Panel] ➝ [System] ➝ [Remote] and un-check “Allow Remote Assistance invitations...” • Enable the Classic Start menu Right click on an empty space in the task bar and select [Properties] ➝ [Start Menu], then check (enable) “Classic Start menu.” • Disable transition effects Select [Control Panel] ➝ [Display] (➝ [Appearance]) ➝ [Effects...] button, and un-check (disable) “Use the following transition effect for menus and tooltips.” 24 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide When the settings of the mLAN Auto Connector or Driver Setup cannot be changed, or when the program mLAN Applications for YAMAHA/mLAN Tools 2.0 cannot be uninstalled. The message below may sometimes appear when changing the settings with mLAN Auto Connector and Driver Setup or when uninstalling. There may be times when you are unable to change the settings in mLAN Auto Connector and Driver Setup and unable to uninstall mLAN Applications for YAMAHA/mLAN Tools 2.0, even when applications are not running. This may occur in the following cases. • The WDM driver is selected in mLAN Auto Connector or mLAN Graphic Patchbay. • When the mLAN WDM driver (“mLAN Audio Out/In 01”) or “mLAN MIDI Out” is selected as the audio device in Windows. If this is the case, follow the instructions below before changing the settings in mLAN Auto Connector and Driver Setup and/or uninstalling mLAN Applications for YAMAHA/mLAN Tools 2.0. • In some cases, when you turn on the power to the mLAN devices, Windows may automatically select mLAN Audio/ MIDI. 1 Select [Start] ➝ [Control Panel] ➝ [Sounds and Audio Devices] ➝ [Voice]. Make sure that something other than “mLAN Audio Out/In 01” is selected for the “Voice playback” and “Voice recording” settings. 2 Select [Start] ➝ [Control Panel] ➝ [Sounds and Audio Devices] ➝ [Audio]. Make sure that something other than “mLAN Audio Out/In 01” is selected for the “Sound playback” and “Sound recording” settings. 3 Select [Start] ➝ [Control Panel] ➝ [Sounds and Audio Devices] ➝ [Audio], then select any option other than the items from “mLAN MIDI OUT” through “mLAN MIDI OUT (8)” for the “MIDI Music Playback” setting. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 25 English When using the mLAN driver with a program such as an audio sequencer, the settings in mLAN Auto Connector and Driver Setup cannot be changed, and mLAN Applications for YAMAHA/mLAN Tools 2.0 cannot be uninstalled. Execute these operation only after closing all applications. Installing the Plug-in Effect (For i88X Users) 1 Double-click on the “VST_” folder. Various files including “Setup.exe” will be displayed. 2 Double-click on “Setup.exe.” “Welcome to the 8 Click [Next]. In the window that appears, you can select the “VstPlugins” folder to which the plug-in effect will be installed. installShield Wizard” window will be displayed. 3 Click [Next]. In the window that appears, enter the User Name, Company Name, and Serial Number. • In order to be able to use the VST plug-in software with the SQ01, it is necessary to check “Program Files\YAMAHA\VstPlugins.” • If no folder is shown in the list, click [Add] then select the folder from the “Browse for Folder” dialog box. English • Serial number is provided in the included Users Card. 4 Click [Next]. The Registration Confirmation window will be displayed. Make sure the registration information you entered is correct, then click [Yes]. • If the information is incorrect, click [No] and return to step 3 above. 5 A window for selecting plug-in effects will be displayed. Select (check) the software you want to install and click [Next]. 6 A window appears prompting you for confirmation of the plug-in effects to be installed. Make sure the information is correct, then click [Yes]. 9 Click [Next]. The installation starts. 10 When the installation is complete, the message “InstallShield Wizard Complete.” appears. Click [Finish]. •When you wish to change the software to be installed, click [Return] and go back to step 5. 7 In the window that appears, you can select the drive and folder to which the owner’s manual (PDF file) and setup program will be installed. You should avoid changing the installation location. • If you want to change the location, click [Browse...] then select the installation location (drive and folder). 26 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide Even after you’ve installed the plug-in effect, if you intend to use it with another VSTcompatible host application, you will need to manually copy the effect plug-in module to the “VstPlugins” folder specified by the host application. 1 Select [Start] ➝ [(All) Programs] ➝ [YAMAHA VST Plugins] ➝ [(Plug-in Effect name)] ➝ [Setup]. A “Welcome” window appears. 2 Select [Modify], then click [Next]. 3 A window appears allowing you to specify the destination location to which the plug-in effect is to be copied. Select (check) the “VstPlugins” folder corresponding to the host application with which you intend to use the plug-in effect. Uninstall (removing the installed plug-in effect) 1 Select [Start] ➝ [(All) Programs] ➝ [YAMAHA VST Plugins] ➝ [(Plug-in Effect name)] ➝ [Setup]. A “Welcome” window appears. 2 Select [Remove], then click [Next]. A window appears prompting you for confirmation of the file deletion. 3 Click [OK] to remove the files. • To cancel the operation, click [Cancel]. • Processing speeds of computers equipped with Pentium I processors and some computers equipped with Pentium IV processors may be reduced significantly if you use Pitch Fix and Cubase SX2.0. If this problem occurs, download from the following URL an updated Pitch Fix Version 1.0.2 or higher: http://www.yamahasynth.com/down/index.htm • If you remove the checkmark from the folder for the installed host-application, you can remove the installed plug-in effect. • For details, refer to the owner’s manual of each host application. 4 Click [Next]. The copy operation is executed. • To cancel the operation, click [Cancel]. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 27 English Using the Installed Plug-in Effect on another host application For Mac OS 9 Users (i88X and mLAN16E only) • Only the i88X and mLAN16E support Mac OS 9. The MY16-mLAN does not support Mac OS 9. Regarding Mac OS X, refer to page 42. CD-ROM Contents Software for Macintosh is included on two CD-ROMs (for the mLAN 16E, only TOOLS for i88X/ mLAN16E is included). Install TOOLS for i88X/mLAN16E first. ● TOOLS for i88X/mLAN16E English Folder Name mLAN_ OMS_ Application Name Contents mLAN Applications for YAMAHA mLAN Tools This software includes mLAN drivers and applications required to make mLAN connections between the mLAN devices and the computer. Install the software while the power to the mLAN devices is off. • For installation instructions, see page 31. A single installation procedure installs all applications necessary for mLAN communications. Software to be installed includes mLAN Auto Connector and mLAN Graphic Patchbay, which enable you to set up audio and MIDI connections for an mLAN network. Open Music System (OMS) 2.3.8*2 This software is required to transfer MIDI data (Remote Control and Studio Manager data) between an mLAN device and a computer. • For instructions on installing, see page 32. OMS Setup for YAMAHA (folder) Contains OMS Setup files for an mLAN device (page 39). ● Plug-in Effect (included only with i88X) • This software can be used as plug-in software within a VST/Audio Units compatible program. • For instructions on how to use the application, refer to the PDF manual. (The destination disk you specified)/YAMAHA/Plug-in Effect/(the relevant software folder) • For instructions on installing the Plug-in Effects, see page 41. 28 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide Mac OS 9 VST_ *3 Application Name Contents 01X Channel Module*1 This software reproduces the EQ and Dynamics effects built into each channel of the YAMAHA Digital Mixing Studio 01X, and uses the processing power of the computer for the effects. You can use the Dynamics and 4-band EQ functions (that can be also found on Yamaha Digital Mixing consoles) as effects software. You can also import the 01X settings, thus reproducing the songs created on the 01X. Pitch Fix*1 This program is used to edit the pitch of recorded vocals. More than just a pitch processor, it can also be used to change the character of the vocals. Moreover, you can use MIDI data on the host application to control the Pitch Fix effect. For more information on setting up with the host application, refer to the Pitch Fix PDF owner’s manual. Vocal Rack*1 This is a multi-effect program for processing vocals. The plug-in features various effects, including a high-pass filter, compressor and a 3-band equalizer. Final Master*1 This is a multi-effect program for mastering purposes. It features a compressor, limiter and soft-clip function, and allows you to split the signal into three bands for separate multi-band processing. *1 These applications are supplied with online/PDF manuals. *2 Unfortunately, Yamaha makes no guarantee concerning the stability of these programs nor can it offer user support for them. *3 Mac OS X Compatibility You can download mLAN software compatible with Mac OS X at the following URL: • mLAN driver (included in OS X 10.3.3 or higher) <http://www.apple.com/support/> • mLAN Tools, Studio Manager for 01X <http://www.yamahasynth.com> The following plug-in effects are included in the “Mac OS X” folder and are compatible with VST and Audio Units. • • • • 01X Channel Module Pitch Fix Vocal Rack Final Master With Macintosh notebook computers such as the iBook or PowerBook, before you start up the computer, first connect the mLAN device and mLAN cable, then turn on the power to the mLAN device. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 29 English Folder Name System Requirements for i88X/mLAN16E Software The system requirements below are necessary for using the included software. • The system requirements below may differ slightly depending on the particular operating system. • For details on minimum requirements for each DAW (Digital Audio Workstation) software, refer to the respective owner’s manual. ● i88X/mLAN16E (including the requirements for mLAN Tools 2.0/mLAN Applications for YAMAHA) English These are the total system requirements, including the audio sequencer, mLAN Tools 2.0/mLAN Applications for YAMAHA and the plug-in effects. OS : Mac OS 9.2 (Mac OS X and Mac Classic environment are not supported.) Computer : System having a built-in S400 (400 Mbps) FireWire terminal. (*1) Hard Disk : Free disk space of 250 MB (i88X)/50 MB (mLAN16E) or more; highspeed hard disk ● Recommended system (*2) • Connecting a single mLAN device to a computer peer-to-peer: Computer : G4/G3 signal processor 900 MHz (or higher) Available Memory : 512 MB or more (Virtual memory must be turned off) • Connecting three mLAN devices to a computer: Computer : G4 1.25GHz Single processor, 1GHz Dual processor, or higher Available Memory : 512 MB or more (Virtual memory must be turned off) ● Minimum system requirements (*2) Computer : G4 dual processor 450 MHz or G4/G3 single processor 700 MHz (or higher) Available Memory : 320 MB or more (Virtual memory must be turned off) *1 The computer must have an IEEE 1394 (FireWire) or i.Link terminal. If there is no terminal, install an IEEE 1394 interface card (PCI or PC). For more details on system requirements and recommended PCI or PC cards, see http://www.yamahasynth.com 30 *2 The system requirements listed here apply when using the included software and when playing audio/MIDI data detailed below on standard sequencer software. This may differ depending the particular sequencer software you are using. Recommended system requirements (Connecting a single mLAN device to a computer peer-to-peer) Fs=44.1kHz/24-bit Audio Driver 18In/18Out (i88X) 16In/8Out (mLAN16E) MIDI Driver 1In/1Out (i88X) 3In/3Out (mLAN16E) 16 MIDI and 12 Audio playback tracks 2 Audio recording tracks 2 Sends for Plug-in Soft Effect 10 Inserts for Plug-in Soft Effect 2 Channels for Plug-in Soft Synthesizer Latency of 5msec or less Recommended system requirements (Connecting a computer and three mLAN devices) Fs=44.1kHz/24-bit Audio Driver 32In/32Out (total) MIDI Driver 4In/5Out (total) 16 MIDI and 8 Audio playback tracks 2 Audio recording tracks 2 Sends for Plug-in Soft Effect 10 Inserts for Plug-in Soft Effect 2 Channels for Plug-in Soft Synthesizer Latency of 5msec or less Minimum system requirements Fs=44.1kHz/16bit Audio Driver 8In/2Out (i88X) 2In/2Out (mLAN16E) MIDI Driver 1In/1Out (i88X) 2In/2Out (mLAN16E) 16 MIDI and 12 Audio playback tracks 2 Sends for Plug-in Soft Effect 6 Inserts for Plug-in Soft Effect No Plug-in Soft Synthesizer Latency of about 50msec TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide ● Plug-in Effect (included only with i88X) OS • Up to two PCI or PC cards can be used. However, you can use only one card at a time. If you are using an IEEE1394 interface built into the computer, you can use only one IEEE1394 PCI or PC interface card. • When using a laptop or notebook computer, a builtin IEEE 1394 terminal may not be available. If this is the case, install an appropriate PC interface card. : Mac OS 8.6 through 9.2 Mac OS X 10.2 through 10.3 • When using a PowerBook under battery power, go Apple menu ➝ [Control Panel] ➝ [Energy Saver] ➝ [Advanced Settings] (Settings for: Battery), and remove the check from the “Allow processor cycling.” Software Installation mLAN software and OMS mLAN Tools 2.0 software includes a driver that enables you to connect mLAN devices to a computer. mLAN Applications for YAMAHA enables audio and MIDI signals to be transferred between a computer and mLAN devices via mLAN cables. This software enables you to connect the i88X, mLAN16E, or 01X to a computer via mLAN. Follow the steps below to install these software applications. • For explanations on error messages, see page 43. • For information on the uninstall (removing the installed application), refer to page 33. Preparing to install 1 Start the computer. 2 Exit from any open applications and close all open windows. •When using the mLAN connection, make sure to disable any energy saving features on the computer (such as Suspend, Sleep, Standby or Pause). When using the virtual memory, turn it off, then restart the computer. • If you are using the S200 data transfer rate standard (check the rear panel of your particular device, or refer to the specifications in the owner’s manual), make sure to uninstall the old version of mLAN Tools beforehand. (Refer to the owner’s manual of your particular device.) 3 Disconnect all MIDI cables connecting MIDI devices to the MIDI IN/OUT of the mLAN device. 4 Using an IEEE1394 (FireWire/iLink) cable, connect the mLAN device directly to the computer (without use of a hub), and disconnect all other IEEE1394-connected devices from the computer. 5 Insert the included CD-ROM (“TOOLS for i88X/mLAN16E”) into the CD-ROM drive. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 31 English For instructions on how to install the software other than one referred to below, see page 28 in the section “CD-ROM Contents.” OMS (Open Music System) mLAN software 6 Double-click on the “OMS_” folder (English 12 Double-click the “YAMAHA mLAN Installer” version only). “Install OMS 2.3.8” will be displayed. 7 Double-click on “Install OMS 2.3.8.” OMS Setup Dialog will be displayed. 8 Execute the installation by following the on- icon in the “mLAN_” folder to display the following installation screen. The “Install Location” box displays the destination of the installation. If you wish to change the destination disk or folder, use the [Switch Disk] button and the pop-up menu to specify the desired destination. screen directions. After the installation, select “Restart.” English • In general, there is no need to change the destination directory. • After the installation is complete, you may encounter an error message warning that the installer did not close. In this case, go to the “File” menu and select “Quit” to close the installer. Then reboot the computer. 9 After restarting the Macintosh, you will find the “Opcode”/“OMS Applications” folder on your computer (Hard Disk, as the default). 10 Copy the “OMS_2.3_Mac.pdf” in the CDROM to the “OMS Applications” folder (drag-and-drop it to the folder). Refer to the “OMS_2.3_Mac.pdf” (English version only) for information on how to use the application. 11 Copy the “OMS Setup for YAMAHA” in the CD-ROM to the “OMS Applications” folder (drag-and-drop it to the folder). In the “OMS Setup for YAMAHA” folder you will find the OMS Setup files for the i88X and mLAN16E, which can be used as templates. 13 Confirm that “Easy install” is selected and click “Install.” At the confirmation message that appears, click “Continue.” 14 If a message “OMS Folder cannot be found in the system folder” or the like appears, after finishing the installation, copy the file “mLAN OMS Driver” (located in “Into OMS Folder” of the “mLAN Tools” folder in the installation destination) to the system folder “OMS Folder.” 15 The message prompting to search the ASIO Drivers folder is shown. Click [OK]. The result of the search will be displayed. 32 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide ASIO mLAN Driver, then click [OK]. • If a message “ASIO Driver folder cannot be found in the system folder” or the like appears, after finishing the installation, copy the file “ASIO mLAN” (located in “Into ASIO Drivers” of the “mLAN Tools” folder in the installation destination) to the “ASIO Drivers” folder of the particular application you are using. 17 Turn on the mLAN device. 18 When installation is finished, an “Installation was successful.” message appears. Click [Restart]. Confirming the installation The mLAN Installer places the following files in the following locations. Control panel folder of the startup disk mLAN Driver Setup (page 34) • You can use the mLAN Driver Setup (page 34) to check whether data is being properly transmitted and received via mLAN. Extensions folder of the startup disk mLAN Driver mLAN Driver Plugs mLAN Expert mLAN Family mLAN Transporter Family English 16 Select the installation destination of the The folder you specify mLAN Tools folder Opcode/OMS Applications System folder Control Panels/mLAN Driver Setup OMS Folder/mLAN OMS Driver Preferences/mLAN HALs/01XTransporter.hal Preferences /mLAN HALs/i88XTransporter.hal Preferences /mLAN HALs/ mLAN16ETransporter.hal Preferences /mLAN Prefs/mLAN Control Panel Prefs Preferences /mLAN Prefs/oui.tbl * Delete the files and folders listed above when uninstalling. Be careful not to delete data already existing before the installation, including files related to OMS. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 33 Changing settings after installation The mLAN-related settings can be changed after installation from the mLAN Driver Setup window. To display it, start the mLAN Driver Setup in the Control Panels folder. mLAN Driver Setup This window lets you check and change the mLAN settings for receiving/transmitting data. Make sure to close any application (DAW, etc.) using the mLAN connection before making changes. • To change the wordclock (sample rate) and the number of channels used, Start the mLAN Auto Connector in the mLAN Tools folder. q English w e t r q FireWire Card ID The options here are the same as those for the 1394 Adapter Card ID parameter for Windows as described on page 15. w Latency Determines the basic latency of the mLAN communications, or how quickly the data is processed after a command is issued. Choose an option appropriate to your environment. About latency in an mLAN network The particular configuration of your computer (processing speed, system memory size, etc.) may affect its ability to properly record and play back audio data in your audio sequencer, resulting in noise or other audio problems. In most cases, you can solve the problem by adjusting the latency (delay time). • A small latency value results in a short delay time and gives optimum response for real-time recording/playback. • A large latency value results in a long delay time, but allows for use of more audio channels and plug-in effects. ● Types of latency in an mLAN network Audio latency (msec) Audio latency is determined by the basic latency (selected in the mLAN Driver Setup window) and Preferred Buffer Size (specified in the ASIO mLAN Control Panel) (see next page). MIDI latency (msec) The MIDI latency value varies with the mLAN driver version. For information on the MIDI latency of your mLAN driver version, refer to the “MIDI_Latency.txt” file, which you can access by selecting [mLAN Tools | YAMAHA | Manual] on the corresponding computer. 34 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide ● ASIO mLAN Control Panel. When using the mLAN ASIO Driver, open the ASIO Control Panel within the driver settings of the DAW software (the particular menu depends on the software you are using) and set the Preferred Buffer Size as needed. • The initial setting of the Preferred Buffer Size of the mLAN ASIO driver is the smallest value. q w e t English r y q FireWire Card ID The options here are the same as those for the 1394 Adapter Card ID parameter for Windows as described on page 15. r Latency It indicates the audio latency value for transmission and reception. Audio latency is determined by the basic latency (selected in the mLAN Driver Setup window) and Preferred Buffer Size (w). w Preferred Buffer Size e Sample Size t OK y Cancel The parameters and buttons function the same as those in the ASIO mLAN Control Panel for Windows as described on page 16. e Status r Set t Revert The field and buttons function the same as those for Windows as described on page 17. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 35 Connecting a Computer to an mLAN device via mLAN English This section explains how to connect a computer to a single mLAN device peer-to-peer in mLAN Auto Connector. In mLAN Auto Connector, you can easily connect an mLAN device by setting up the wordclock and specifying the number of audio I/O channels. To connect multiple mLAN devices to a computer, use mLAN Graphic Patchbay. For more information on mLAN Graphic Patchbay, refer to the mLAN Graphic Patchbay Online Manual. • If you use Auto Connector after you make connections in mLAN Graphic Patchbay, the connections made in mLAN Graphic Patchbay will be cancelled. • You can also use mLAN Graphic Patchbay to connect a computer to a single mLAN device peer-to-peer. • mLAN Auto Connector windows may appear different when certain mLAN devices are connected. 1 Connect a computer to an mLAN device using an IEEE1394 cable. 2 Open the “mLAN Tools” folder, then click the Noise may be generated during the following operations. Before performing these operations, lower the output level of each device. “mLAN Auto Connector” icon. mLAN Auto Connector starts. 3 Set up the wordclock and specify the number • Turning the power to the computer and mLAN devices on or off • Connecting or disconnecting an IEEE1394 (mLAN) cable • Making an mLAN connection in mLAN Auto Connector • Changing the wordclock master and slave status in mLAN Auto Connector or mLAN Graphic Patchbay • Selecting On or Off in mLAN Manager (Windows) • Starting or quitting the OS • Installing/uninstalling mLAN software of audio channels (see below), then click the [Connect] button. The computer and mLAN device are connected via mLAN. Connecting the i88X q w e r t y u i o !0 !1 q Nickname w Model Name This field indicates the nickname of the connected i88X. To change the nickname, refer to “Node Information” in the mLAN Graphic Patchbay Online Manual. This parameter enables you to select an mLAN device to which you wish to make an mLAN connection in a multiple mLAN device network. 36 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide e [Update] button i Mac ← i88X Clicking this button updates the information on the mLAN devices connected to the mLAN network. Use this button when you add an mLAN device to the network while mLAN Auto Connector is running. This parameter enables you to specify the number of channels for audio data that are input at the i88X’s INPUT 1-8 jacks (analog), DIGITAL STEREO COAXIAL or OPTICAL IN jack (digital), or ADAT IN jack (ADAT) and output to the computer. r [Identify] button o [Connect] button Clicking this button causes the i88X ACTIVE indicator to flash for a few seconds. Click this button to connect the i88X to the computer via mLAN. t Sample Rate !0 [Cancel] button This parameter enables you to specify the sampling frequency (wordclock frequency). Click this button to cancel the settings and close mLAN Auto Connector. !1 [Setup] button These buttons enable you to specify the computer or i88X as the wordclock master. Click this button to open the i88X Control Panel window, which enables you to set the wordclock transition speed. u Mac → i88X This parameter enables you to specify the number of channels of audio data routed from the computer’s audio output (mLAN driver’s audio output) into the i88X. Signals input in the i88X are output from the i88X’s OUTPUT 1-8 jacks (analog), DIGITAL STEREO COAXIAL or OPTICAL OUT jack (digital), or ADAT OUT jack (ADAT). Connecting the mLAN16E (MOTIF ES) q w e r t y u i o !0 !1 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 37 English y Wordclock Master radio buttons q Nickname This field indicates the nickname of the connected mLAN16E. To change the nickname, refer to “Node Information” in the mLAN Graphic Patchbay Online Manual. w Model Name This parameter enables you to select an mLAN device to which you wish to make an mLAN connection in a multiple mLAN device network. When the mLAN16E is connected, select the name of the device equipped with an mLAN16E. English e [Update] button Clicking this button updates the information on the mLAN devices connected to the mLAN network. Use this button when you add an mLAN device to the network while mLAN Auto Connector is running. r [Identify] button Clicking this button causes the mLAN16E ACTIVE indicator to flash for a few seconds. t Sample Rate This parameter enables you to specify the sampling frequency (wordclock frequency). y Wordclock Master radio buttons These buttons enable you to specify the computer or mLAN16E as the wordclock master. u Mac → MOTIF ES This parameter enables you to specify the number of channels of audio data input into the mLAN16E from the computer’s audio output (mLAN driver’s audio output). i Mac ← MOTIF ES This parameter enables you to specify the number of channels of audio data input into the computer from the mLAN16E’s output. • The number of audio transmission channels and MIDI ports varies on different mLAN16E-compatible devices. 38 • For more information on audio and MIDI connections for an MOTIF ES with an mLAN16E installed, refer to “System Examples” in the mLAN16E Owner’s Manual. o [Connect] button Click this button to connect the mLAN16E to the computer via mLAN. !0 [Cancel] button Click this button to cancel the settings and close mLAN Auto Connector. !1 [Setup] button Click this button to open the mLAN16E Control Panel window, which enables you to set the wordclock transition speed. Setting the wordclock transition speed (mLAN Control Panel) When you click the [Setup] button in the Node Information window in mLAN Auto Connector or mLAN Graphic Patchbay, the computer displays the mLAN Control Panel, which enables you to set the wordclock transition speed. The Wordclock Transition Speed parameter enables you to specify how fast the initial wordclock setting will change to a new setting if the mLAN device is operating as a slave in the mLAN network. Slow: Select this option in most cases. Fast: Select this option if the wordclock master device is referencing timecode, such as MTC, thus changing the wordclock setting. 4 Click the [Connect] button. When the mLAN device is connected correctly, mLAN Auto Connector closes and mLAN communications start. • If connection fails, restart mLAN Auto Connector, then click the [Connect] button again. You do not need to restart the computer. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide Setting up OMS • If you are using mLAN on your Macintosh with an optionally installed IEEE 1394 (FireWire) interface card, recreate a new Studio Setup by OMS Setup included in the installation CD-ROM. For details, refer to the OMS manual. 1 Double-click on the “OMS” folder and “OMSSetup for YAMAHA” folder. The “i88X-mLAN,” “MOTIF-ES-mLAN” and “mLAN Generic 16 ports” files appear. Copy this to the hard disk on your computer. mLAN16E (including MOTIF ES) using Auto Connector, double-click “i88X-mLAN” or “MOTIF ES-mLAN.” If you are connecting multiple mLAN devices using Graphic Patchbay or connecting a single mLAN16E (excluding MOTIF ES) using Auto Connector, double-click “mLAN Generic 16 Ports.” The OMS Setup starts. 3 After starting the OMS Setup, the Studio setup The setting names (device names) of each MIDI port are as shown below, when the Studio Setup file is loaded. Select the proper device (port) for the application you are using. i88X (Auto Connector) port function MIDI Port 1 • Double clicking the icon of the mLAN device or executing “MIDI Device Info...” from the “Studio” menu by selecting the mLAN device, calls up the Device Info dialog box. We recommend that you not change the channel assignment since this is already set by the setup application (mLAN Auto Connector, etc.) for optimum use with i88X and mLAN16E. Reset the settings as shown in the illustration below if you have inadvertently changed them. Device Name MIDI Function i88X’s MIDI port (MIDI to (from) mLAN MIDI conversion) MOTIF ES (Auto Connector) port function file double-clicked in step 2 opens. If “ ” is not indicated at the right of the setup file name, select “Make Current” from the “File” menu and execute the save operation. The OMS studio setup has been completed. You’ll also need to set the OMS port when using the software. Refer to the owner’s manual for your application. English 2 If you are connecting a single i88X or MIDI Port Device Name Function 1 TG Controls a tone generator. 2 PLG Controls a Plug-in. 3 Remote B Controls a DAW or editor. 4 Remote A Controls a DAW or editor. • You can assign a function to each MIDI port on the MOTIF ES. This example uses typical device names. Port functions in mLAN Graphic Patchbay and on the mLAN16E (excluding MOTIF ES) MID Port Device Name 1 Port 1 2 Port 2 .... .... 16 Port 16 Function Port functions vary depending on the specific mLAN device. Refer to the owner’s manual for your mLAN device. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 39 • The port numbers in the “mLAN Generic 16 ports” Studio Setup correspond to the numbers indicated in the “Connector Name” column in mLAN Graphic Patchbay. For more information on Graphic Patchbay, refer to the Graphic Patchbay Online Manual. English • After the OMS studio setup above has been completed, your computer will recognize only Yamaha mLAN (MIDI) devices. If you are connecting other musical instruments via USB, or if you add an mLAN (MIDI) device to the network while you are already using OMS, you should create an original Studio Setup file. For details, refer to the on-line manual supplied with OMS. • The included OMS studio setup file may not function even if you follow the above procedure, depending on your Macintosh/Mac OS version. (MIDI data cannot be transmitted/received even if the setup becomes available.) In this situation, connect your Macintosh to the mLAN device and follow the procedure below to recreate the setup file. 1 Start OMS Setup and select “New Setup” from the “File” menu. 2 The “OMS Driver Search” dialog appears. Remove the check from the “Modem” and “Printer” check boxes, and click [Search] to execute the device search. If the Search operation has been completed successfully, the [mLAN-01] device is displayed in the OMS driver setting dialog. 3 Click the [OK] button to search for ports. If you are using the i88X or mLAN16E, Port 1, Port 2 ... appears in the dialog. Mark the appropriate checkbox of the port and click the [OK] button to store the setting. 40 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide Plug-in Effect 1 Double-click on the “Mac OS 9” folder. “VST_” folder will be displayed. 2 Double-click on the “VST_” folder. “VST Plu- 5 Click [Continue]. In the window that appears, you can select the “VstPlugins” folder to which the plug-in effect will be installed. gin Installer.” will be displayed. 3 Double-click on “VST Plugin Installer.” 4 Click [Install]. In the window that appears, enter the User Name, Company Name, and Serial Number. • Serial number is provided in the included Users Card. • If there is only one “VstPlugins” folder in your computer, this step is unnecessary. Go on to step 7. • If there is no “VstPlugins” folder in your computer, you can select the location to which the plug-in effect will be installed, in the window that appears. 6 Click [OK]. The installation starts. 7 When the installation is complete, the following screen appears. 8 To finish the installation, click [Quit]. To copy the module to a location other than selected in step 5 above, click [Continue] and repeat the procedure from step 3. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 41 English A window for selecting plug-in effects will be displayed. In the window, the “Install Location” box displays the destination of the owner’s manual (PDF file). You should avoid changing the installation location. Select (check) the software you want to install. For Mac OS X Users The included CD-ROM does not include mLAN software for Mac OS X. If you will be using the i88X, mLAN16E, or MY16-mLAN with Mac OS X, please download the following software from the URLs listed below. • mLAN driver (OS X10.3.3 or higher) <http://www.apple.com/support/> • mLAN Tools <http://www.yamahasynth.com> English For i88X users • The software included in the Mac OS X folder of the CD-ROM (Plug-in Effect) is VST/Audio Units compatible versions of the 01X Channel Module, Pitch Fix, Vocal Rack, and Final Master that can be used with Mac OS X. 42 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide Display Messages Page 19, 36 The settings of the mLAN Driver could not be changed. 1) If an application that uses the driver is currently active, close it first, then change the settings. 2) There is not enough resource memory. 25 Failed to initialize the mLAN settings because the application “mLAN Start” is not running. Select “ON” from the menu of “mLAN Manager” application. 14 Can’t connect the **’s mLAN audio output connector to the computer’s mLAN audio input connector. 14, 19, 36 Can’t connect the **’s mLAN MIDI output connector to the computer’s mLAN MIDI input connector. 14, 19, 36 Can’t connect the computer’s mLAN MIDI output connector to the **’s mLAN MIDI input connector. 14, 19, 36 Can’t connect the computer’s mLAN wordclock output connector to the **’s mLAN wordclock input connector. 14, 19, 36 Can’t connect the **’s mLAN wordclock output connector to the computer’s mLAN wordclock input connector. 14, 19, 36 A new 1394 adaptor card has been found. If you’ve inserted a new card, restart the computer. There is not enough resource memory. Execute mLAN Stop, then execute mLAN Start again. If this fails, restart the computer. 14 The 1394 adaptor card has not been found. Check the card and start mLAN again. 14 One of the programs could not be started. Follow the instructions/messages in the appropriate application. If there are no messages, execute mLAN Start again or restart the computer. 14 The application is not responding. Execute mLAN Start again or restart the computer. 14 Failed to load the mLAN Bus Driver. If the New Hardware Wizard has not been run, use it to install the hardware, then execute mLAN Start. 14 One or more programs could not be closed. After quitting all DAW programs and any programs using mLAN, execute mLAN Stop. 14 • ** will be the name of the mLAN device you’re using. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 43 English Messages Can’t find the ** on the mLAN network. Make sure that the ** is turned on and that the mLAN cable connection is correct and secure. After that, restart “mLAN Auto Connector”. Troubleshooting If you encounter a problem... If you hear no sound or a strange sound, first check the items described below and take appropriate action. If the problem persists, consult your Yamaha dealer. English ■ Unable to communicate via mLAN • Has the driver been installed? ................................................................................ See page 12. • Is the mLAN cable properly connected? Check the connection; disconnect the mLAN cable once, then insert it again. • (For Windows) Is mLAN set to “ON”? From the task bar, right click on the mLAN Manager icon. ........................................................................................................... See page 14. • (For Windows) When adding a new IEEE 1394 card, right click on the mLAN Manager icon in the task bar and select “ON.”. ..................................................................................... See page 14. • Is the ACTIVE lamp on the rear panel of the mLAN device lit (in blue)? If it is not lit, check the followings: - In mLAN Driver Setup, is the Status indicator blue? If not, restart the mLAN device and reenable connection by using mLAN Auto Connector or mLAN Graphic Patchbay. ........... Refer to page 19, page 36, and “mLAN Connection Settings” in the mLAN Graphic Patchbay Online Manual. • Has connection been enabled with mLAN Auto Connector and/or Graphic Patchbay? Re-enable connection if necessary. ........... Refer to page 19, page 36, and “mLAN Connection Settings” in the mLAN Graphic Patchbay Online Manual. • Have you changed the device? Even if the model is the same, if the actual device is different, it is necessary to re-enable connection by using Auto Connector and/or Graphic Patchbay. ........... Refer to page 19, page 36, and “mLAN Connection Settings” in the mLAN Graphic Patchbay Online Manual. • Is there a loop connection? Check the cabling and make sure none of the devices are connected in a loop. Example of loop connection Computer Computer mLAN device mLAN device : IEEE1394-equipped device • There may be a limit on the IEEE 1394 interface of your computer as to the number of ports that can be used simultaneously. Check how many ports can be used simultaneously. • Turn off all devices on the mLAN network (except the computer) and re-connect each device one-by-one until the device causing the problem is found. • (For Windows) (When removing the mLAN bus from the [Safely Remove Hardware] setting of the task bar.) Restart the computer when using mLAN again. • With Macintosh notebook computers such as the iBook and PowerBook, always first connect the mLAN device and mLAN cable then turn on the power of the mLAN device, before starting up the computer. 44 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide • Make sure that you set up the wordclock correctly. Also, make sure that one node is assigned as master and the other nodes are assigned as slaves. ........... Refer to “mLAN Connection Settings” in the mLAN Graphic Patchbay Online Manual. ■ The computer processing speed is too slow. ■ The computer’s CPU meter indicates a heavy processing load. ■ Playback response is delayed. • If multiple S200-compatible devices are connected to the network, connecting mLAN devices in mLAN Graphic Patchbay may require more time. • (For Windows) Mobile computers with Intel CPU SpeedStep ™ technology is applied for some CPU’s (CPU for notebook PC). Please disable the SpeedStep ™ technology when mLAN is employed. SpeedStep ™ technology changes CPU clock dynamically depending on the loading on the CPU to save the power consumption. - How to disable the SpeedStep™ technology; In almost all of the PC’s, BIOS has a function to select enabling or disabling the SpeedStep™ technology. Please refer to the PC’s operating manual, or make inquiry to the PC manufacturer. ■ Unable to change the mLAN settings • (For Windows) Is the mLAN (WDM) driver selected as the default audio device for the system? - Select [Start | Control Panel | Sounds and Audio Devices | Voice]. Make sure that something other than “mLAN Audio 01” is selected for the [Voice playback] and [Voice recording] settings. - Select [Start | Control Panel | Sounds and Audio Devices | Audio]. Make sure that something other than “mLAN Audio 01” is selected for the [Sound playback] and [Sound recording] settings. - In “MIDI music playback,” select any option other than the range of options from “mLAN MIDI Out” through “mLAN MIDI Out (8).” • (For Windows) Select [Start | Control Panel | Sounds and Audio Devices | Sounds]. And select “No sounds” in the [Sound scheme], then execute again. • If you cannot quit mLAN (by selecting “OFF” after right clicking the mLAN icon in the task bar), end the processes listed below manually. ([Ctrl] + [Alt] + [Delete] → [Processes] → select process → [End process]) When finished, start mLAN Manager to change the mLAN settings again. - mLANVDevice.exe - mLANTFamily.exe - mLANSoftPH.exe - mLANManager.exe • To change mLAN settings, select [Start | (All) Programs | Start Up], then start mLAN Manager. • (When a message such as “file cannot be found” appears when uninstalling:) Try executing the installation once more, then uninstall again. ■ (Windows) mLAN Manager (the mLAN icon in the Task bar) has disappeared. • Select [Start | (All) Programs | Start Up (or mLAN Tools)], then select mLAN Manager. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 45 English ■ Inconsistency in wordclock, or unable to exit from Auto Connector ■ A connected mLAN device is not recognized. • Refresh the information by selecting [View], then [Update] in the Menu bar. If the device is still not recognized, turn mLAN Manager off, then turn it on, then select [Update] to latest information. ........... Refer to “Starting mLAN Graphic Patchbay” in the mLAN Graphic Patchbay Online Manual. ■ Launching mLAN Graphic Patchbay or updating to the latest information takes a while. English • When you try to update the network information after connecting or disconnecting an mLAN device that does not support S400, the system adjusts the mLAN transfer speed, and requires more time to process your request. However, this will not affect any subsequent operations. • If five or more mLAN devices (including a computer) have been connected to a network, the total number of transmission channels of all devices will be limited. You can connect up to 86 channels in Windows and up to 98 channels in a Macintosh system. • For information on audio problems such as no sound or excess noise, refer to the Troubleshooting section of the i88X/ mLAN16E/MY16-mLAN Owner’s Manual. 46 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide SOFTWARE LICENSING AGREEMENT The following is a legal agreement between you, the end user, and Yamaha Corporation (“Yamaha”). The enclosed Yamaha software program is licensed by Yamaha to the original purchaser for use only on the terms set forth herein. Please read this licensing agreement with care. Opening this package indicates that you accept all terms outlined herein. If you do not agree to the terms, return this package unopened to Yamaha for a full refund. In the event that you obtained the enclosed Yamaha software program(s) as a part of a software package or software bundled with a hardware product, you may not return the enclosed Yamaha software program(s) to Yamaha. 1. GRANT OF LICENSE AND COPYRIGHT Yamaha grants you, the original purchaser, the right to use one copy of the enclosed software program and data (“SOFTWARE”) on a single-user computer system. You may not use it on more than one computer or computer terminal. The SOFTWARE is owned by Yamaha and is protected by Japanese copyright laws and all applicable international treaty provisions. You are entitled to claim ownership of the media in which the SOFTWARE is included. Therefore, you must treat the SOFTWARE like any other copyrighted materials. The SOFTWARE program is copyrighted. You may not engage in reverse engineer-ing or reproduction of the SOFTWARE by other conceivable methods. You may not reproduce, modify, change, rent, lease, resell, or distribute the SOFTWARE in whole or in part, or create derivative works from the SOFTWARE. You may not transmit or network the SOFTWARE with other computers. You may transfer ownership of the SOFTWARE and the accompanying written materials on a permanent basis provided that you retain no copies and the recipient agrees to the terms of the licensing agreement. 3. TERMINATION The licensing condition of the software program becomes effective on the day that you receive the SOFTWARE. If any one of the copyright laws or clauses of the licensing conditions is violated, the licensing agreement shall be terminated automatically without notice from Yamaha. In this case, you must destroy the licensed SOFTWARE and its copies immediately. 4. PRODUCT WARRANTY Yamaha warrants to the original purchaser that if the SOFTWARE, when used in normal conditions, will not perform the functions described in the manual provided by Yamaha, the sole remedy will be that Yamaha will replace any media which proves defective in materials or workmanship on an exchange basis without charge. Except as expressly set forth above, the SOFTWARE is provided “as is,” and no other war-ranties, either expressed or implied, are made with respect to this software, including, without limitation the implied warranties of merchantability and fitness for a particular purpose. 5. LIMITED LIABILITY Your sole remedies and Yamaha’s entire liability are as set forth above. In no event will Yamaha be liable to you or any other person for any damages, including without limitation any incidental or consequential damages, expenses, lost profits, lost savings or other damages arising out of the use or inability to use such SOFTWARE even if Yamaha or an authorized dealer has been advised of the possibility of such damages, or for any claim by any other party. 6. GENERAL This license agreement shall be interpreted according to and governed by Japanese laws. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installation Guide 47 English 2. RESTRICTIONS SOFTWARE-LIZENZVEREINBARUNG Die folgende Vereinbarung ist eine rechtsgültige Vereinbarung zwischen Ihnen, dem Endanwender, und der Yamaha Corporation (“Yamaha”). Yamaha erteilt dem ursprünglichen Käufer für das beiliegende Yamaha-Softwareprogramm ausschließlich zu den hier ausgeführten Bedingungen eine Lizenz zur Verwendung. Bitte lesen Sie diese Lizenzvereinbarung sorgfältig. Durch das Öffnen dieser Packung bringen Sie zum Ausdruck, dass Sie alle darin enthaltenen Bedingungen akzeptieren. Wenn Sie nicht mit den Bedingungen einverstanden sind, können Sie die Packung ungeöffnet an Yamaha zurückgeben; der Kaufpreis wird in voller Höhe zurückerstattet. Falls Sie das mitgelieferte Softwareprogramm bzw. die mitgelieferten Softwareprogramme von Yamaha als Teil eines Softwarepakets oder im Paket mit einem Hardwareprodukt erworben haben, sind Sie nicht berechtigt, das mitgelieferte Softwareprogramm bzw. die mitgelieferten Softwareprogramme an Yamaha zurückzugeben. 1. ERETILUNG VON LIZENZ UND COPYRIGHT Yamaha erteilt Ihnen, dem ursprünglichen Käufer, das Recht, ein Exemplar des beiliegenden Softwareprogramms und der darin enthaltenen Daten (“SOFTWARE”) als Einzelperson auf jeweils einem Computer zu verwenden. Sie dürfen sie nicht auf mehr als einem Computer bzw. einer Computerstation verwenden. Die SOFTWARE bleibt im Besitz von Yamaha und ist durch japanische Copyrightgesetze sowie alle anwendbaren internationalen Vertragsbestimmungen geschützt. Sie haben ein Anspruchsrecht auf das Eigentum an den Medien, denen die SOFTWARE beiliegt. Daher müssen Sie die SOFTWARE wie alle anderen durch Copyright geschützten Materialien behandeln. 2. EINSCHR Die SOFTWARE ist durch Copyright geschützt. Sie dürfen Sie weder analysieren noch durch anderweitige Methoden reproduzieren. Sie dürfen die SOFTWARE weder ganz noch teilweise reproduzieren, modifizieren, verändern, gegen Entgelt oder unentgeltlich verleihen, verkaufen oder vertreiben, und Sie dürfen auf der Grundlage der SOFTWARE keine Ableitungen erstellen. Sie dürfen die SOFTWARE nicht an andere Computer senden oder in Netzwerke einspeisen. Sie dürfen das Eigentum an der SOFTWARE und den schriftlichen Begleitmaterialien auf unbefristeter Basis unter den Voraussetzungen übertragen, daß Sie keine Kopien zurückbehalten und sich der Empfänger mit den Bedingungen der Lizenzvereinbarung einverstanden erklärt. Deutsch 3. BEENDIGUNG Die Lizenzbedingung des Softwareprogramms wird am Tag, an dem Sie die SOFTWARE erhalten, wirksam. Falls ein Copyrightgesetz oder eine Bestimmung der Lizenzbedingungen verletzt wird, wird automatisch und ohne Benachrichtigung durch Yamaha die Lizenzvereinbarung beendet. In diesem Fall müssen Sie die lizensierte SOFTWARE und ihre Kopien unverzüglich vernichten. 4. PRODUKTGARANTIE Yamaha garantiert dem ursprünglichen Käufer, daß, falls die SOFTWARE bei Verwendung unter normalen Bedingungen nicht die in der von Yamaha bereitgestellten Anleitung beschriebenen Funktionen erfüllt, die einzige Abhilfe darin bestehen wird, daß Yamaha auf Austauschbasis kostenlos jedes Medium ersetzen wird, das Material- oder Verarbeitungsfehler aufweist. Abgesehen von dem oben Ausgeführten wird die SOFTWARE “wie die Ware liegt und steht” geliefert, und es werden keine anderen ausdrücklichen oder stillschweigenden Garantien hinsichtlich dieser Software übernommen, einschließlich, aber nicht beschränkt auf, die stillschweigenden Garantien für handelsübliche Qualität und Eignung für einen bestimmten Einsatzzweck. 5. BESCHR Ihre einzige Abhilfe und die gesamte Haftung Yamahas bestehen in dem oben Ausgeführten. Keinesfalls haftet Yamaha Ihnen oder einer anderen Person gegenüber für etwaige Schäden, einschließlich, aber nicht beschränkt auf, zufällige Schäden oder Folgeschäden, Kosten, Verdienstausfall, verlorene Ersparnisse oder andere Schadenersatzansprüche, die aus der Verwendung der SOFTWARE oder aus der Tatsache hervorgehen, daß diese SOFTWARE nicht verwendet werden konnte, selbst wenn Yamaha oder ein autorisierter Händler über die Möglichkeit derartiger Schadenersatzansprüche informiert wurde, oder für etwaige andere Ansprüche einer anderen Partei. 6. ALLGEMEINES Diese Lizenzvereinbarung soll gemäß und in Übereinstimmung mit den japanischen Gesetzen ausgelegt werden. 48 TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Installationshandbuch CONTRAT DE LICENCE DE LOGICIEL Ceci est un contrat entre vous-même, l’utilisateur final, et Yamaha Corporation (« Yamaha »). Le logiciel Yamaha ci-inclus est concédé sous licence par Yamaha à l’acheteur original et ne peut être utilisé que dans les conditions prévues aux présentes. Veuillez lire attentivement ce contrat de licence. Le fait d’ouvrir ce coffret indique que vous acceptez l’ensemble des termes du contrat. Si vous n’acceptez pas lesdits termes, renvoyez le coffret non ouvert à Yamaha pour en obtenir le remboursement intégral. Si vous avez obtenu le(s) programme(s) logiciel(s) Yamaha inclus avec un package ou fourni(s) avec un produit matériel, vous ne pouvez pas le(s) renvoyer à Yamaha. 1. CONCESSION DE LICENCE ET DROITS D’AUTEUR Yamaha vous concède le droit d’utiliser, en tant qu’acheteur original, un exemplaire du logiciel et des données afférentes à celui-ci (« LOGICIEL ») sur un ordinateur pour utilisateur unique. Vous n’êtes pas autorisé à utiliser ces éléments sur plus d’un ordinateur ou terminal d’ordinateur. Le LOGICIEL est la propriété de Yamaha. Il est protégé par les dispositions relatives au droit d’auteur contenues dans la législation japonaise et les traités internationaux. Vous êtes en droit de revendiquer l’appartenance du support du LOGICIEL. A ce titre, vous devez traiter le LOGICIEL comme tout autre élément protégé par le droit d’auteur. 2. RESTRICTIONS Le LOGICIEL est protégé par le droit d’auteur. Vous n’êtes pas autorisé à reconstituer la logique du LOGICIEL ou à reproduire ce dernier par quelque autre moyen que ce soit. Vous n’êtes pas en droit de reproduire, modifier, prêter, louer, revendre ou distribuer le LOGICIEL en tout ou partie, ou d’utiliser le LOGICIEL à des fins de création dérivée. Vous n’êtes pas autorisé à transmettre le LOGICIEL à d’autres ordinateurs ou à l’utiliser en réseau. Vous êtes en droit de céder, à titre permanent, le LOGICIEL et la documentation imprimée qui l’accompagne, sous réserve que vous n’en conserviez aucun exemplaire et que le bénéficiaire accepte les termes du présent contrat. 3. RESILIATION Les conditions énoncées dans le présent contrat de licence prennent effet à compter du jour où le LOGICIEL vous est remis. Si l’une quelconque des dispositions relatives au droit d’auteur ou des clauses du contrat ne sont pas respectées, le contrat de licence sera résilié de plein droit par Yamaha, ce sans préavis. Dans ce cas, vous devrez immédiatement détruire le LOGICIEL concédé sous licence ainsi que les copies réalisées. 4. GARANTIE PRODUIT 5. RESPONSABILITE LIMITEE Votre unique recours et la seule responsabilité de Yamaha sont tels qu’énoncés précédemment. En aucun cas Yamaha ne pourra être tenu responsable, par vous-même ou une autre personne, de quelques dommages que ce soit, notamment et de manière non limitative, de dommages indirects, frais, pertes de bénéfices, pertes de fonds ou d’autres dommages résultant de l’utilisation ou de l’impossibilité d’utiliser le LOGICIEL, même si Yamaha ou un distributeur agréé ont été prévenus de l’éventualité de tels dommages, ou de quelque autre revendication formulée par une tierce partie. 6. REMARQUE GENERALE Le présent contrat de licence est régi par le droit japonais, à la lumière duquel il doit être interprété. TOOLS for i88X/mLAN16E, TOOLS for MY16-mLAN, Plug-in Effect Manuel d’installation 49 Français Si, dans des conditions normales d’utilisation, le LOGICIEL ne remplit pas les fonctions décrites dans le manuel fourni, Yamaha s’engage vis-à-vis de l’acheteur original à remplacer gratuitement, sur la base d’un échange, tout support reconnu défectueux par suite d’un défaut de matière première ou d’un vice de fabrication. Ceci constitue le seul recours opposable à Yamaha. Hormis dans les cas expressément énoncés plus haut, le LOGICIEL est livré « en l’état » et toute autre garantie expresse ou implicite le concernant, y compris, de manière non limitative, toute garantie implicite de qualité marchande et d’adéquation à un usage particulier, est exclue. This document is printed on chlorine free (ECF) paper with soy ink. Auf Umweltpapier mit Sojatinte gedruckt. Ce document a été imprimé sur du papier non blanchi au chlore avec de l'encre d'huile de soja. U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2004 Yamaha Corporation WD50930 409APAP1.2-01A0 Printed in Japan
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50

Yamaha mLAN16E Guía de instalación

Categoría
Teclados
Tipo
Guía de instalación
Este manual también es adecuado para