VGA-to-CAT5
Video Splitters and Receiver
AC600A
AC601A
AC602A
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: [email protected]
CUSTOME
R
SUPPORT
INFORMATION
A
C600A (Shown) & AC601A
2 & 4 Channel VGA to Cat5 Splitter / Extender
A
C602A
VGA over Cat5 Receive
r
UMA1034 Rev. n/c
VGA-to-CAT5 Video Splitters and Receiver
1
TRADEMARKS USED IN THIS MANUAL
BLACK BOX and its logo
are registered trademarks of Black Box
Corporation.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
IBM is a registered trademark of International Business Machines
Corporation.
SGI is a registered trademark of Silicon Graphics, Inc.
Sun and Sun Microsystems are registered trademarks of Sun Microsystems,
Inc. in the United States and other countries.
Any other trademarks mentioned in this manual are acknowledged to be the
property of the trademark owners.
Models AC600A, AC601A, AC602A
2
FEDERAL COMMUNICATIONS COMMISSION
AND CANADIAN DEPARTMENT OF COMMUNICATIONS
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used properly, that is, in strict accordance with
the manufacturer’s instructions, may cause interference to radio
communication. It has been tested and found to comply with the limits
for a Class A computing device in accordance with the specifications in
Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when the equipment is
operated in a commercial environment. Operation of this equipment in
a residential area is likely to cause interference, in which case the user
at his own expense will be required to take whatever measures may be
necessary to correct the interference.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This digital apparatus does not exceed the Class A limits for radio
noise emission from digital apparatus set out in the Radio Interference
Regulation of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe
A prescrites dans le Règlement sur le brouillage radioélectrique publié
par le ministère des Communications du Canada.
EUROPEAN UNION DECLARATION OF CONFORMITY
This product complies with the requirements of the European EMC
directive 89/336/EEC
VGA-to-CAT5 Video Splitters and Receiver
3
Normas Oficiales Mexicanas (NOM)
Electrical Safety Statement
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el
aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia
futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación
deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina
de baño, lavabo, sótano mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean
recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo
descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a
personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su
uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o superficie
similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes que
impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como
radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores)
que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo
descrito en el instructivo de operación, o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del
equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados
ni pellizcados por objetos colocados sobre o contra ellos, poniendo particular
atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones
del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de
energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por
un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados
sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
Models AC600A, AC601A, AC602A
4
Contents
1. Introduction ..............................................................................page 5
1.1 General ................................................................................page 5
1.2 Features ...............................................................................page 5
2. Installation .................................................................................page 6
3. Configuration & Operation........................................................page 8
4. Troubleshooting.........................................................................page 9
5. Specifications...........................................................................page 10
VGA-to-CAT5 Video Splitters and Receiver
5
1. Introduction
1.1 General
This manual describes the features, setup, and operation of the Black
Box 2 and 4 channel VGA-to-CAT5 Video Splitters/Extenders and
their corresponding Receiver.
The splitters convert a PC's VGA signal into a format that can be
transmitted using inexpensive and commonly available Category-
5/5e/6 Unshielded Twisted Pair (UTP) cable to 500 feet away.
At the receiving (remote) ends the Cat5 signal is converted back to
VGA for connection to monitors, projector or other display devices.
Besides the 2 or 4 RJ45 outputs, the splitters feature a VGA connector
for connection to a local monitor or for daisy-chaining to other
splitters.
Furthermore, the splitters include a power supply that is capable of
powering itself and all the AC602A Receivers (phantom power) which
makes for a clean and easy setup (note that if the length of Cat5 cable
is longer than 300 feet to a particular receiver, the receiver may
require its own power supply).
The system can also transmit Component Video (Y Pb Pr at resolutions
to 1080i) instead of VGA with the purchase of HD15-to-3RCA break-
out cable for each end. Therefore you can use these devices to send
Standard TV and HDTV component video to multiple locations.
1.2 Features
• Send PC or Component Video at full-resolution to multiple
locations using Category-5 cable.
• Buffered video for connection to local monitor at sender
• Supports resolutions up to 1600x1200 including 1080i
• Rugged, Reliable, Compact size
• Drive standard CAT5 cables to 500 feet
• Transmits video and Power on one Cat5 cable
• Easily expandable by daisy-chaining using local VGA port
Models AC600A, AC601A, AC602A
6
Figure 1 – AC600A Front Figure 2 – AC600 Rear
2. Installation
1. Connect the VGA IN of the AC600A or AC601A to the
computer's video port using the supplied cable
2. If desired, connect a local display to the VGA out port of the
Transmitter unit.
3. Using Category 5 cables connect the RJ45 ports of the Transmitter
to the Model AC602A Receiver.
4. Connect the Remote displays to the VGA output port of the
AC602 Receivers.
5. Plug in the supplied Power supply to the Power Input jack of the
Transmitter unit.
6. Turn on the local and remote displays, then the PC
Figure 3 – Setup Block Diagram
VGA-to-CAT5 Video Splitters and Receiver
7
NOTES
If the length of Cat5 Cable is longer than 300 feet you
may need to attach a power supply to the receiver unit. The
power supply will need to be the same as the sending unit (i.e.
9VDC regulated, Center Positive with 2.5mm connector). If there
is no image at the remote or the image is intermittent, you may
need a power supply at the receiver, please contact Black Box
to purchase one. Generally if the remote display device is
referenced to ground (i.e. the VGA connector ground or case, is
connected to power line ground) you should not need an
additional power supply to the specified maximum length of 500
feet
Do not connect this unit to any LAN device such as
network cards or hubs as this may damage the AC155A and/or
the LAN device. Use EIA/TIA 568B standard straight-through
patch wiring. Do not use crossover cables.
For cable runs of 300 feet or longer it is recommended
that you use a UTP cable that is optimized for video (low skew
cable). We recommend Belden Cable’s “Brilliance®
VideoTwist(tm)” Category 5 Cable for best results.
If you want to transmit component video, then contact
Black Box to purchase HD15-to-3 RCA adapter cables for the
inputs and outputs.
Figure 4 – HD15-to-3 RCA adapter Cable
Models AC600A, AC601A, AC602A
8
Figure 5
3. Configuration & Operation
The Model AC602A Mini-CAT5 Receivers
are equipped with an adjustment to improve
image quality when using long cables. The
adjustment is made via a single turn trim-pot
located next to the power connector on the
side.
When using a long cable, with no
compensation, any solid horizontal line, tends
to smear to the right. For example in the
image shown on the right, observe the dark
black line at the bottom of the window and
see how it is smearing to the right (not
changing to white abruptly as it should). This
is the effect of long cable on the signal.
You can turn the trim-pot to eliminate these
streaks as shown on the 2nd picture. If you
add too much compensation to the signal,
then an opposite effect may be observed, i.e.
black lines smear to the right as white lines or
vice-versa. The 3rd picture shows the case
where too much compensation is added.
When using long cables, the image quality is
a function of resolution and refresh rate.
Lower resolution or refresh rate, result in best
picture. Therefore it is best to set the refresh
rate to 60 Hz at any resolution.
No-Compensation
Perfect Compensation
Too much Compensation
VGA-to-CAT5 Video Splitters and Receiver
9
4. Troubleshooting
1. Fuzzy, blurry, or ghosting image at remote location
If you have a stable image but it looks too blurry (object or character
edges are smearing), try to adjust the compensation first. See Section 3.
If you still have a fuzzy image, try reducing the refresh rate and/or the
resolution of the PC. For Best results use either low-skew cable (such
as Belden Brilliance® VideoTwist), or Cat5 (instead of Cat6).
2. Shaking image or periodically blanking monitor
The employs CAT5 cable’s twisted pairs to differentially transmit the
signals, however, a strong electromagnetic noise field can cause
instability in the signal. Usual sources of this form of noise coupling
are high current AC lines or other high-density data and/or control
cables that run adjacent to and parallel with a substantial length of the
CAT5 cable.
To eliminate this, either separate the Cat 5 cable of Mini-CAT5
Extender from the interfering source or use shielded CAT5 cables.
Note that separating the CAT5 cable from the EMI source by a few
inches is often sufficient to eliminate this problem.
If the length of Cat5 run exceeds 300 feet you may need an additional
power supply at the receiver (see first note in Section 2)
Contacting Black Box
If you determine that your extender is malfunctioning, do not attempt
to repair the unit. Contact Black Box at 724-746-5500. Before you do,
make a record of the problem. We will be able to provide more
efficient and accurate assistance if you have a complete description.
Shipping and Packaging
If you need to transport or ship your extender:
• Package it carefully. Use the original container if possible.
• Before you shipping the unit, contact us to get a Return
Authorization (RA) number.
Models AC600A, AC601A, AC602A
10
5. Specifications
(a) Common Specs.
Video Types RGBHV analog or YPbPr / YCbCr through HD15
Resolution Up to 1600 x 1200 at up to 85 Hz
Bandwidth DC to 250 MHz
Max. Distance Up to 328 ft. (100 m) with Phantom Power, or 500 ft
(150 m) with additional power supply at receiver
Connectors HD15 female for video in and out; Shielded RJ45
Interfaces Standard Analog VGA; Proprietary CAT5
Compliance CE; FCC Part 15 Subpart B Class A, IC Class
Max. Altitude 10,000 ft. (3048 m)
Temperature Operating: 32 to 122°F (0 to 50°C);
Storage: –40 to +185°F (–40 to +85°C)
Humidity Up to 95% non-condensing
(b) Transmitter Specs.
Enclosure Steel
MTBF 90,000 hours (calculated estimate)
Power From utility-power (mains) outlet, through included
Universal power adapter. Input Voltage: 100~240
VAC Output Voltage: 9v DC regulated Center-Positive
at 1.7A Max
Size & Weight AC600A 1.22"H x 4.86"W x 2.60"D, 1.8 lbs
AC601A 1.22"H x 8.20"W x 3.00"D, 2.4 lbs
VGA-to-CAT5 Video Splitters and Receiver
11
(c) Receiver Specs. (Model AC602A)
Enclosure Plastic ABS-94VO, UL File#56070
MTBF 200,000 hours (calculated estimate)
Size 0.8” H x 1.7” W x 4.5” L
Weight 1 lbs.
Models AC600A, AC601A, AC602A
12
© Co
py
ri
g
ht 2007. Black Box Cor
p
oration. All ri
g
hts reserved.
1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746
724-746-5500 | blackbox.com
Page 2
Whitepapers
Cabinets and Racks
Retrofitting with passive water cooling at the rack level.
Extending the Life of Your Data Center
Selecting cooling systems for IT equipment cabinets is not always as simple
as it might seem.
Six Things to Know When Cooling IT Equipment Cabinets
Cables
What’s in the ANSI/TIA 1179 standard.
ANSI/TIA 1179 Healthcare Infrastructure Standard
Buyer beware: If the price seems too good to be true, it is.
Counterfeit cable: The dangers, risks, and how to spot it.
Using CAT 6A in 10-GBe networks.
CAT 6A F/UTP vs. UTP: What You Need to Know
When is fiber the ideal choice for your network?
Fiber Optic Technology
Key cabling infrastructure standards.
Structured Cabling Organizations and Standards
Carts and Storage
12 Questions to Ask When Choosing a Tablet and Laptop Cart
E-Learning Device Storage
Communications Solutions
10 Tips for Securing a Strong ROI.
Voicemail to Unified Communications
Compliance Solutions
The key to protecting data in motion.
Group Encryption
Digital Signage and Multimedia
Deliver the right message at the right time.
A Beginner’s Guide to Digital Signage
7 Questions You to Need to Ask when Choosing a Signage System. Deliver
real-time communications, including emergency messaging, to students,
faculty, and staff.
Choosing the Right Digital Signage System
Best practices for creating high-value, compelling content that delivers
extraordinary results.
Digital Signage Content 101
Why your school or university needs digital signage and how to implement it.
Digital Signage in Education
Digital Signage and Multimedia (Continued)
Deliver real-time communications—including emergency messaging—to
students, teachers, and staff.
Digital Signage for K–12
Everything you need to ask when planning and evaluating digital signage.
The Roadmap to Digital Signage Success
Falling victim to these common mistakes can cost you both time and money.
Seven Pitfalls to Avoid When Planning Digital Signage
Industrial
Connect industrial equipment to your network by using USB.
Bridging the Gap: USB Converters
Learn about system configuration, cabling selection, transient protection,
software, and device selection.
The Elements of an RS-422 and RS-485 System
When is fiber the ideal choice for your network?
Fiber Optic Technology
Understanding Power Needs for Industrial Control Devices
Industrial Power Solutions
Run wireless even in extreme environments.
Industrial Wireless
Interface and Protocol Converters
Connect industrial equipment to your network by using USB.
Bridging the Gap: USB Converters
Learn about system configuration, cabling selection, transient protection, soft-
ware, and device selection.
The Elements of an RS-422 and RS-485 System
Go beyond the five-meter USB distance limitation with USB extenders! Read
How to extend USB and break the five-meter barrier.
Extending the Benefits of USB
KVM
An overview of extension and switching technologies in high-performance
KVM environments.
HD Video and Peripheral Matrix Switching and Extension
Get secure local KVM console access and secure remote IP server access.
Security with the ServSwitch Wizard IP
Use this transparent and reliable switching technology to avoid the limitations
of traditional emulations.
USB True Emulation for KVM Switches
Resources
Appendix: Resources
Do you have technical questions about this product or similar technology? Check out the Resources listed below or contact our
FREE Technical Support at 724-746-5500 or info@blackbox.com.
White Papers: To dowload a white paper, click on the corresponding link listed below:
724-746-5500 | blackbox.com
Page 3
Whitepapers
Networking
Eliminate the need to buy and install expensive network equipment by
using wireless Ethernet extension.
5 Questions You Need to Ask When Choosing Wireless Ethernet Extenders
Integrate fiber optic cabling to add speed, distance, and cost savings.
Media Converters
Add low-voltage devices and network equipment in industrial environments
without running power.
Power over Ethernet in Industrial Applications
Is your network ready?
Tablets in Education
Common network mistakes that cost money, cause downtime, and create
frustration.
Top 10 Network Mistakes
Take these ten steps to ensure wireless success: Ten Commandments of
Wireless Communications white paper.
Wireless Communications
Run wireless even in extreme environments.
Industrial Wireless
Wireless Networking: wireless standards, architecture, security and more
white paper. A basic overview of standards, installation, and security.
Wireless Networking
Network Security
The key to protecting data in motion.
Group Encryption
Physical Security
See why it’s just as important as software-based security.
Physical Network Security
Power
Understand the power needs for industrial control devices.
Industrial Power Solutions
Understanding the risks to your network and how to choose the right
solution.
Power Protection
Add low-voltage devices and network equipment in industrial environments
without running power.
Power over Ethernet in Industrial Applications
Testers and Tools
See how industrial-strength Ethernet has come of age.
Ethernet in Harsh Environments
Learn about the top three growth drivers for fiber networks: greater band-
width needs, increased storage demands, and the transition to higher network
speeds.
Improve the Quality of Fiber Installations with Extended Fiber Certification
Meet the need for implementation speed without sacrificing accuracy.
Proven Techniques and Best Practices for Managing Infrastructure Changes
Move your private networks in premises and campus environments towards
high-speed applications.
Testing Today’s High-Speed Multimode Fiber Infrastructure
Use easy-to-install, standardized, plug-and-play technology.
Troubleshooting Your Industrial Network
Be sure to complete this step when installing a new local area network
segment.
Validate LAN Installations for Optimal Service Delivery
Wireless
Ten Commandments of Wireless Communications white paper. Take these ten
steps to ensure wireless success.
Wireless Communications
Run wireless even in extreme environments.
Industrial Wireless
Is your network ready?
Tablets in Education
A basic overview of standards, installation, and security.
Wireless Networking
Resources
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
Black Box AC601A Manual de usuario
- Categoría
- Extensores de red
- Tipo
- Manual de usuario
en otros idiomas
- English: Black Box AC601A User manual
Artículos relacionados
-
Black Box AC340A-R2 Manual de usuario
-
-
Black Box AVSC-HDMI-VGA Manual de usuario
-
Black Box AC561A-250 Manual de usuario
-
Black Box VX-HDMI-TP-100M Manual de usuario
-
-
Black Box 2ch VGA Manual de usuario
-
-
-
Black Box FiberPath AC444A Especificación