Yamaha DTX432K Electronic Drum Set El manual del propietario

Marca: Yamaha

Modelo: DTX432K Electronic Drum Set

Categoría: Tambores musicales

Tipo: El manual del propietario

Este manual también es adecuado para

Owner’s Manual

ELECTRONIC DRUM KIT

DTX402K

DTX432K

DTX452K

DTX402K DTX432K DTX452K Owner’s Manual

S-1

For Instrument

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or specifically

recommended by Yamaha.

WARNING:

Do not place this product in a position where anyone

could walk on, trip over, or roll anything over power or connecting cords of

any kind. The use of an extension cord is not recommended! If you must

use an extension cord, the minimum wire size for a 25’ cord (or less) is 18

AWG. NOTE: The smaller the AWG number, the larger the current han-

dling capacity. For longer extension cords, consult a local electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at

the time of printing. However, Yamaha reserves the right to change or

modify any of the specifications without notice or obligation to update

existing units.

This product, either alone or in combination with an amplifier and

headphones or speaker/s, may be capable of producing sound levels

that could cause permanent hearing loss. DO NOT operate for long

periods of time at a high volume level or at a level that is uncomfort-

able. If you experience any hearing loss or ringing in the ears, you

should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory mount-

ing fixtures that are either supplied with the product or as optional

accessories. Some of these items are designed to be dealer assem-

bled or installed. Please make sure that benches are stable and any

optional fixtures (where applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are

not covered by the manufacturer’s warranty, and are therefore the

owners responsibility. Please study this manual carefully and consult

your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and envi-

ronmentally friendly. We sincerely believe that our products and the

production methods used to produce them, meet these goals. In keep-

ing with both the letter and the spirit of the law, we want you to be

aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of

battery is approximately five years. When replacement becomes nec-

essary, contact a qualified service representative to perform the

replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery

being charged.

When installing batteries, never mix old batteries with new ones, and

never mix different types of batteries. Batteries MUST be installed cor-

rectly. Mismatches or incorrect installation may result in overheating

and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all bat-

teries away from children. Dispose of used batteries promptly and as

regulated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some rea-

son its useful life is considered to be at an end, please observe all

local, state, and federal regulations that relate to the disposal of prod-

ucts that contain lead, batteries, plastics, etc. If your dealer is unable

to assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this manual

as a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

SPECIAL MESSAGE SECTION

92-BP (bottom)

COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Electronic Drum Kit

Model Name : DTX402K, DTX432K, DTX452K

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (FCC DoC)

S-2

DTX402K DTX432K DTX452K Owner’s Manual

For AC adaptor and Instrument

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifi-

cations not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accesso-

ries and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used.

Follow all installation instructions. Failure to follow instruc-

tions could void your FCC authorization to use this product

in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these require-

ments provides a reasonable level of assurance that your

use of this product in a residential environment will not

result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions found in

the users manual, may cause interference harmful to the

operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not

occur in all installations. If this product is found to be the

source of interference, which can be determined by turning

the unit “OFF” and “ON”, please try to eliminate the problem

by using one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to dis-

tribute this type of product. If you can not locate the appro-

priate retailer, please contact Yamaha Corporation of

America, Electronic Service Division, 6600 Orangethorpe

Ave, Buena Park, CA90620

The above statements apply ONLY to those products dis-

tributed by Yamaha Corporation of America or its subsidiar-

ies.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

DTX402K DTX432K DTX452K Owner’s Manual

S-3

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den ar ansluten till vägguttaget, även om själva apparaten

har stängts av.

ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt, sålænge netledningen sidder i en stikkontakt, som er tændt

— også selvom der er slukket på apparatets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta.

For AC adaptor

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-

lowing two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

(can_b_02)

CAN ICES-3 (B)/NMB-3(B)

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and mainte-

nance (servicing) instructions in the litera-

ture accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accor-

dance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-

cles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tri-

pod, bracket, or table specified

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualified service personnel. Ser-

vicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

DTX402K DTX432K DTX452K Owner’s Manual

Contents

PRECAUTIONS ............................................ 4

Welcome....................................................... 7

About the Manuals ...................................... 7

Printed Manual .................................................. 7

Digital Manual (PDF)......................................... 7

Setup

First Steps.................................................... 8

Package Contents ....................................... 9

Assembly Guide ........................................ 12

Setting Up for Sound ................................ 21

Connecting the Power ..................................... 21

Connecting Headphones or Speakers ............ 21

Connecting a Music Player ............................. 21

Turning On the Drum Module.......................... 22

Turning Off the Drum Module.......................... 22

Auto Power-Off ................................................ 22

Restoring the Default Settings

(Factory Reset)........................................... 22

Panel Controls & Functions ..................... 23

Control Panel .................................................. 23

Bottom Panel................................................... 24

Top Panel ........................................................ 24

Basic Techniques

Playing Techniques................................... 25

Snare Pad ....................................................... 25

Hi-hat Cymbal ................................................. 25

Crash Cymbal ................................................. 25

Performing with

a Selected Music Category..................... 26

Selecting a Music Category ............................ 26

Adjusting Kit Sensitivity................................... 26

Performing with a Song................................... 27

Adjusting the Song Volume............................. 27

Adjusting the Volume of Muted Drum Parts .... 28

Importing a MIDI song .................................... 28

Using the Metronome ............................... 29

Starting and Stopping the Metronome ............ 29

Adjusting the Metronome Volume ................... 29

Confirming Tempo........................................... 29

Adjusting the Tempo ....................................... 30

Other Settings ................................................. 30

Practicing in Training Mode ...................... 31

Before Training ................................................ 31

Detailed Training settings ................................31

After Training ...................................................31

Switching to a different exercise ...................... 31

1. RHYTHM GATE ........................................... 32

2. RHYTHM GATE........................................... 32

3. DYNAMIC GATE..........................................33

4. SONG PART GATE .....................................34

5. SONG SCORE GATE.................................. 35

6. MEASURE BREAK ..................................... 36

7. CHANGE UP ............................................... 37

8. PART MUTE................................................ 38

9. FAST BLAST ............................................... 39

10. RECORDER..............................................40

Advanced Techniques

Setting Parameters using Menu Mode..... 41

Basic Menu Mode Procedure .......................... 41

z Metronome Settings.................................... 42

x Kit Settings.................................................. 43

c MIDI Settings .............................................. 45

v Hi-hat Settings ............................................46

b Trigger Settings...........................................48

n Training Settings ......................................... 51

m Other Settings.............................................53

Integrating Separately

Sold Accessories.....................................57

For DTX402K Owners ..................................... 57

For DTX432K & DTX452K Owners ................. 57

Connecting to a Computer........................58

Installing the Yamaha Steinberg USB Driver ... 58

MIDI-related Reference ................................... 58

Reference

Troubleshooting.........................................59

Data List .....................................................62

Specifications ............................................64

Index ...........................................................65

DTX402K DTX432K DTX452K Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

• This AC adaptor is designed for use with only Yamaha electronic

instruments. Do not use for any other purpose.

• Indoor use only. Do not use in any wet environments.

CAUTION

• When setting up, make sure that the AC outlet is easily accessible. If

some trouble or malfunction occurs, immediately turn off the power

switch of the instrument and disconnect the AC adaptor from the outlet.

When the AC adaptor is connected to the AC outlet, keep in mind that

electricity is flowing at the minimum level, even if the power switch is

turned off. When you are not using the instrument for a long time, make

sure to unplug the power cord from the wall AC outlet.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the

following:

• Do not place the power cord near heat sources such as heaters or

radiators. Also, do not excessively bend or otherwise damage the cord,

or place heavy objects on it.

• Only use the voltage specified as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

• Use the specified adaptor (page 64) only. Using the wrong adaptor can

result in damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust which

may have accumulated on it.

• Under no circumstances should any of the components of this product

be taken apart or customized. Doing so could result in electric shock,

fire, injury, or malfunction.

• Do not expose the instrument to rain, use it near water or in damp or

wet conditions, or place on it any containers (such as vases, bottles or

glasses) containing liquids which might spill into any openings. If any

liquid such as water seeps into the instrument, turn off the power

immediately and unplug the power cord from the AC outlet. Then have

the instrument inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item

may fall over and cause a fire.

• When one of the following problems occur, immediately turn off the

power switch and disconnect the electric plug from the outlet. Then

have the device inspected by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

For AC adaptor

For Instrument

Power supply/AC adaptor

Assembly

Water warning

Fire warning

If you notice any abnormality

DMI-5 1/2

DTX402K DTX432K DTX452K Owner’s Manual

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-

connector. Doing so can result in lower sound quality, or possibly

cause overheating in the outlet.

• When removing the electric plug from the instrument or an outlet,

always hold the plug itself and not the cord. Pulling by the cord can

damage it.

• Remove the electric plug from the outlet when the instrument is not to

be used for extended periods of time, or during electrical storms.

• Read carefully the attached documentation explaining the assembly

process. Failure to assemble the instrument in the proper sequence

might result in damage to the instrument or even injury.

• Do not place hands or feet under a foot switch or foot pedal. Doing so

could result in injury.

• Do not use the electronic drum kit’s rack to hold acoustic drums. Doing

so could cause clamps to break and the drums to fall off, which in turn

could lead to injury.

• Mind your fingers when adjusting clamps. Fingers can easily be caught

and crushed if care is not taken during this operation.

• Be careful with the tips of supports, arms, screws, and the like. Fingers

can easily be injured by sharp tips if these components are not handled

carefully.

• Do not sit or stand on the rack. Doing so could cause it to fall over or

break, possibly causing injury.

• Be careful with the holders for cymbal and tom pads as they have sharp

tips. In order to avoid injury, therefore, you should take special care

whenever handling these components.

• Be careful with the anti-slip stoppers on kick pads and foot pedals as

they have sharp tips. In order to avoid injury, therefore, you should take

special care whenever handling these components.

• Securely tighten fixing nuts and other fasteners. In addition, be sure to

immediately tighten any nuts that have come loose. If this precaution is

not observed, pads may fall off or the rack may collapse or fall over,

possibly causing injury.

• Take care when setting up cables. If anyone were to trip on a cable, the

instrument could topple over and cause injury.

• Do not place the instrument in an unstable position where it might

accidentally fall over.

• The flooring material (wooden floor, etc.) may be damaged if the

instrument is placed directly on the floor. We recommend that you

place it on carpet or the like.

• Before moving the instrument, remove all connected cables, to prevent

damage to the cables or injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction occurs,

immediately turn off the power switch and disconnect the plug from the

outlet. Even when the power switch is turned off, electricity is still

flowing to the product at the minimum level. When you are not using

the product for a long time, make sure to unplug the power cord from

the wall AC outlet.

• Use only the stand/rack specified for the instrument. When attaching it,

use the provided screws only. Failure to do so could cause damage to

the internal components or result in the instrument falling over.

• Before connecting the instrument to other electronic components, turn

off the power for all components. Before turning the power on or off for

all components, set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels

and gradually raise the volume controls while playing the instrument to

set the desired listening level.

• Avoid contact with grease. Grease is applied to pedals as a lubricant,

which may attach to your clothes when carrying or setting up them.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on

the panel. This could cause physical injury to you or others, damage to

the instrument or other property, or operational failure.

• Do not rest your weight on, or place heavy objects on the instrument,

and do not use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of

time at a high or uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing loss or ringing

in the ears, consult a physician.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (all lamps are off), electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

Power supply/AC adaptor

Assembly

Location

Connections

Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

DMI-5 2/2

DTX402K DTX432K DTX452K Owner’s Manual

NOTICE

To avoid the possibility of malfunction/damage to the prod-

uct, damage to data, or damage to other property, follow

the notices below.

 Handling and Maintenance

• Do not use the instrument in the vicinity of a TV, radio,

stereo equipment, mobile phone, or other electric

devices. Otherwise, the instrument, TV, or radio may

generate noise.

When you use the instrument along with an applica-

tion on your smart device such as a smartphone or

tablet, we recommend that you set “Airplane Mode” to

on on that device in order to avoid noise caused by

communication.

• Do not expose the instrument to excessive dust or

vibrations, or extreme cold or heat (such as in direct

sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disfiguration, damage

to the internal components or unstable operation.

• Do not place vinyl, plastic or rubber objects on the

instrument, since this might discolor the panel.

 Maintenance

• When cleaning the drum module, use a soft and dry/

slightly damp cloth. Do not use paint thinners, sol-

vents, alcohol, cleaning fluids, or chemical-impreg-

nated wiping cloths.

• When cleaning the pads, avoid cleaning products that

contain organic solvents, paint thinner, and alcohol as

they can cause discoloration and/or warping. Instead,

we recommend that you remove dust using a soft dry

cloth or wipe clean with a moist, tightly-wrung-out

cloth. If a pad is very dirty, wipe the dirt away using a

cloth moistened with a neutral detergent solution and

tightly wrung out. Following this, wipe away the deter-

gent solution using a cloth soaked in water and tightly

wrung out.

Information

 About copyrights

• Copying of the commercially available musical data

including but not limited to MIDI data and/or audio

data is strictly prohibited except for your personal use.

• This product incorporates and bundles contents in

which Yamaha owns copyrights or with respect to

which Yamaha has license to use others’ copyrights.

Due to copyright laws and other relevant laws, you are

NOT allowed to distribute media in which these con-

tents are saved or recorded and remain virtually the

same or very similar to those in the product.

* The contents described above include a computer program,

Accompaniment Style data, MIDI data, WAVE data, voice

recording data, a score, score data, etc.

* You are allowed to distribute medium in which your perfor-

mance or music production using these contents is

recorded, and the permission of Yamaha Corporation is not

required in such cases.

 About this manual

• The illustrations and LCD screens as shown in this

manual are for instructional purposes only, and may

appear somewhat different from those on your instru-

ment.

• Apple, iTunes, Mac, Macintosh, iPhone, iPad, iPod

touch and Lightning are trademarks of Apple Inc.,

registered in the U.S. and other countries.

• IOS is a trademark or registered trademark of Cisco

in the U.S. and other countries and is used under

license.

• The company names and product names in this man-

ual are the trademarks or registered trademarks of

their respective companies.

(bottom_en_01)

The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the

bottom of the unit. You should note this serial number in the space provided below and retain this manual as a perma-

nent record of your purchase to aid identification in the event of theft.

Model No.

Serial No.

DTX402K DTX432K DTX452K Owner’s Manual

Welcome

Thank you for purchasing this Yamaha product.

To get the most out of your DTX402 series Electronic Drum Kit, be sure to read this

Owner’s Manual carefully. And after reading through this manual, be sure to store it in

a safe place so that you can refer back to it again as needed.

About the Manuals

The following manuals are provided for using the DTX402K, DTX432K, and DTX452K. These manuals

are intended for users of the DTX402K, DTX432K, and DTX452K.

Owner’s Manual (this book)

Describes how to assemble your electronic drum kit and get it set up for playing.

Describes the basic techniques used when operating and playing the electronic drum kit.

Describes the setting of parameters and other more advanced modes of use.

Describes troubleshooting techniques and contains other reference materials.

MIDI Reference Manual

This provides MIDI-related reference information.

Drum Scores

This provides drum scores for preset songs of the drum module.

iPhone/iPad Connection Manual

Describes how to connect smart devices such as an iPhone and iPad.

The digital format manuals listed above can be obtained from the Yamaha Downloads web page. To do so, go to the

web page using the following URL, enter your drum kit name in the “Model Name” field, and then click “Search.”

Printed Manual

Digital Manual (PDF)

Yamaha Downloads: https://download.yamaha.com/

After accessing the Support website (and clicking on “Manual Library”), enter the appropriate model name.

Setup

Basic Techniques

Advanced Techniques

Reference

Setup

DTX402K DTX432K DTX452K Owner’s Manual

First Steps

Open the box and confirm that all parts are present

and correct.

Assemble the parts.

• The assembly process is described in detail on pages 9 through

20.

Make the necessary connections.

• Connect the pads to the drum module using the cables provided.

 See page 20.

• Connect the AC adaptor to the drum module and turn on the

module.

 See page 21.

Play your electronic drum kit.

• Basic techniques used when operating and playing the electronic

drum kit are described in the Basic Techniques section (pages 25

to 40).

• More complex methods are described in the Advanced Tech-

niques section (pages 41 to 56).

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Package Contents

After opening up the package containing your electronic drum kit, please verify that all of the follow-

ing parts are present.

DTX402K

Rack (Large)

Stopper

Rack (Small)

Hi-hat holder Cymbal holders (×2)

No Stopper

Cymbal/hi-hat pads (×2) Crash cymbal pad Drum module

Sensor (bumps)

HH40 Hi-hat controller KU100 Kick unit Nine-channel snake cable

Drum key Cable bands (×2) AC adaptor

* May not be included depending on

your area. Check with your Yamaha

dealer.

Owner’s Manual (this booklet)

Package Contents

Setup

DTX402K DTX432K DTX452K Owner’s Manual

DTX432K

HH65

Hi-hat controller

KP65

Kick pad

FP6110A

Foot pedal

Nine-channel snake cable Drum key Cable bands (×2)

Rack (Large)

Stopper

Rack (Small)

Hi-hat holder Cymbal holders (×2)

No Stopper

Cymbal/hi-hat pads (×2) Crash cymbal pad Drum module

Sensor (bumps)

AC adaptor

* May not be included

depending on your area.

Check with your Yamaha

dealer.

Owner’s Manual

(this booklet)

Package Contents

Setup

DTX402K DTX432K DTX452K Owner’s Manual

DTX452K

Rack (Small) TP70S Snare pad

S wing bolt

HH65

Hi-hat controller

KP65

Kick pad

FP6110A

Foot pedal

Nine-channel snake cable Drum key Cable bands (×2)

Cymbal/hi-hat pads (×2) Crash cymbal pad Drum module

Sensor (bumps)

AC adaptor

* May not be included

depending on your area.

Check with your Yamaha

dealer.

Owner’s Manual

(this booklet)

Rack (Large)

Stopper

Hi-hat holder Cymbal holders (×2)

No Stopper

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Assembly Guide

Fully assembled drum kit (DTX452K shown)

CAUTION

• Choose a flat, hard surface on which to assemble your electronic drum kit.

• Take care to avoid mixing up parts or assembling them in the wrong direction. In addition,

the assembly steps should be completed one at a time in the order described.

• The assistance of at least one other person will be required when assembling the elec-

tronic drum kit.

• Once a piece has been assembled, be sure to tighten the corresponding key bolts.

• To disassemble your electronic drum kit, carry out the assembly sequence in reverse.

Step 8

Step 7

Step 6

Step 4

Step 3Step 2

Step 12

Step 9

Step 10

Step 5

Step 9

Step 1

Step 12Step 11

Assembly Guide

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Standing up the Large rack

1. Stand up the Large rack with the rear of the tom pads facing towards you as shown in the figure.

2. Loosen the  key bolt using the drum key.

3. Pull the shorter leg towards you.

Standing up the Small rack

1. Stand up the Small rack as shown in the figure and support it by hand.

2. Loosen the  key bolt.

3. Open the lower pipe approximately 70° as shown in the Top view.

For the DTX452K, the snare pad will be attached to the Small rack in the following step.

Step 1

Rack (Large)

To ms

Step 2

Rack (Small)

70°

Top view

Assembly Guide

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Assembling the rack

1. Loosen the  key bolt on the rack (Large) and turn the joint around before sliding the Small rack (in the next step).

2. Slide the Small rack fully back into the joint in Step 1.

3. Open the left and right legs as shown in the Top view.

4. Tighten the one  and five s key bolts to secure the entire rack.

Attaching the snare pad

1. Take the snare pad and the S wing bolt and lightly tighten the S wing bolt. (Five or six turns is sufficient.)

2. Place the snare pad on the hexagonal rod and slide it fully back. Then tighten the S wing bolt to secure the snare pad in

place.

3. Loosen the  key bolt and adjust the angle of the snare pad. When finished, retighten the  key bolt to secure the snare

pad in place.

For the DTX452K, the snare pad will be attached to the Small rack in the following step.

CAUTION

The rack may topple over and cause injury if the left and right legs are opened too wide.

The pads will be rotated into place in a later step.

Step 3

Rack (Small)

110 °

Top view

Rack (Large)

Joint

110 °

NOTE

Step 4

For DTX452K

S wing bolt

Hexagonal rodSnare pad

Assembly Guide

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Rotating the pads into place

Step 5 applies to each of the four pads.

Step 5 applies to each of the three tom pads. For adjusting the snare pad, see .

1. Loosen the  key bolt on each of the pads.

2. Rotate the pads to positions where they will be easy to play. (If necessary, refer to the picture of the properly assembled kit

on page 12.)

3. Tighten each of the key bolts to secure the pads in place.

Attaching the hi-hat holder

1. Loosen the two  key bolts in the back of the snare part.

2. Insert the hi-hat holder into the back of the snare part as shown in the figure.

• When correctly inserted, the tip of the hi-hat holder will protrude slightly from the bottom of the snare part.

• When correctly oriented, the hi-hat holder will be horizontal to the snare part as shown in the Top view.

3. Tighten the two  key bolts to secure the hi-hat holder.

For DTX402K and DTX432K

For DTX452K

For the snare pad, you can also adjust the angle of the joint which supports the snare pad by loosening the s key bolt.

The hi-hat holder and the other two cymbal holders seem similar, but are actually different.

Only the hi-hat holder has a washer and stopper.

Step 5

Step 4

Snare pad

NOTE

Step 6

Hi-hat holder

Stopper

Top view

Washer

Assembly Guide

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Attaching the hi-hat pad

 Adjusting the position of the hi-hat stopper

1. Loosen the  key bolt on the stopper, which is located at the top of the hi-hat holder.

2. Adjust the position of the stopper until it is straight in the back (as shown in the illustration) from your playing position.

3. Tighten the  key bolt to secure the stopper.

 Assembling the hi-hat pad

1. Remove the wing nut, the washer, and the upper felt pad from

the hi-hat holder. (Do not remove the lower felt pad.)

2. Place the hi-hat pad, which does NOT have a sticker labeled

“CRASH,” on the hi-hat holder with the stopper also passing

through the hole provided.

3. Replace the felt pad removed in Step 1 above the hi-hat pad.

4. Replace the washer removed in Step 1 above the felt pad.

5. Tighten the wing nut to secure the hi-hat pad in place.

Attaching the drum module

1. Loosen the  key bolt on the back left of the rack and turn the joint around before sliding the sliding the drum module (in

the next step).

2. Loosen the s key bolt and slide the drum module fully back into the joint in Step 1.

3. Tighten the  and s key bolts to secure the drum module in place.

Step 7

Playing position

Stopper

Wing nut

Felt pad

Hi-hat pad

Hi-hat holder

Stopper

Washer

Felt pad

Step 8

Assembly Guide

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Attaching the cymbal holders

1. Loosen the four  key bolts at the ends of the tom 1/2 part.

2. Insert the cymbal holders into the ends of the top 1/2 part. Then adjust the angles of the cymbal holders until they are ori-

ented as shown in the figure.

• When correctly inserted, the tips of the cymbal holders will protrude slightly from the bottom of the tom part.

• When correctly oriented, the cymbal holders will bend in the back from your playing position.

3. Tighten the four  key bolts to secure the cymbal holders in place.

Assembling the cymbal pads

1. Remove the wing nut and the upper felt pad from the cymbal holder. (Do

not remove the lower felt pad.)

2. Place the cymbal pad on the cymbal holder, with the holder passing

through the central hole.

3. Replace the felt pad removed in Step 1 above the cymbal pad.

4. Tighten the wing nut to secure the cymbal pad in place.

The two cymbal holders are identical.

The crash cymbal, which has the sticker labeled “CRASH” on the rear side and has some bumps on the front side, is

for the left.

The normal cymbal, which is identical with the hi-hat cymbal, is for the right.

Step 9

Playing position

NOTE

Step 10

Sensor (bumps)

Wing nut

Felt pad

Cymbal holder

Cymbal pad

Assembly Guide

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Assembling the kick pad

1. Remove the four wing bolts, spring washers, and flat washers from the kick pad, and arrange each set

nearby in the disassembled condition.

2. Assemble the base to the kick pad as shown below, and then from the base side, assemble the wing

bolts, spring washers, and flat washers removed in

Step 1 in order to secure it in place.

3. Insert the connecting rods into the holes in the holder of the foot pedal as shown below.

4. Slide the beater into the hole until the tip protrudes approximately 15 mm from the rear, and then tighten the beater bolt

using the drum key.

5. Turn the foot pedal’s T-bolt counter-clockwise to loosen it.

6. Fit the raised section at the front of the kick pad holder into the foot-pedal’s assembly bracket.

7. Turn the foot pedal’s T-bolt clock wise to secure the parts together.

8. Operate the pedal and confirm whether the beater head strikes the kick pad near the center. If not, adjust the length of the

beater or move it left or right as required.

Step 11

For DTX432K and DTX452K

Kick pad

Wing bolt

Spring washer

Flat washer

Base

Kick pad

Foot pedal

Holder

Connecting rod

Drum key Beater

Beater bolt

T-bolt

Assembly bracket Raised section T-bolt

Beater head

Assembly Guide

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Positioning the hi-hat controller and kick drum

Arrange the hi-hat controller and the kick drum parts or kick unit as shown in the figure.

Fine-tuning the positions of the pads and the drum module

Sit on your stool (sold separately) and adjust the positions of the pads and the drum module to your liking.

IMPORTANT

The hi-hat controller and the kick unit from the DTX402K are almost identical in appearance. They

can be told apart by the sticker on the base section.

CAUTION

• Be sure to always retighten any key bolt after you have finished adjusting the corresponding part.

• Before moving on to the next step, ensure that all key bolts have been tightened.

Step 12

DTX402K DTX432K, DTX452K

KickHi-hat controller Hi-hat controller

Kick drum parts

Step 13

Assembly Guide

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Connecting the pads to the drum module

1. Insert the mini plugs* at one end of the nine-channel snake cable into the correct trigger input jacks (SNARE to KICK/

PAD) on the drum module. (*: The smaller set of plugs.)

2. Insert the nine-channel snake cable’s standard plugs* into the jacks in the corresponding pads. (*: The larger set of plugs.)

3. Wrap the cables for the snare pads, the tom pads, and the cymbal/hi-hat pads around the cord clip to prevent them from

being pulled out.

4. Using the cable bands, secure the cables to the kit rack at the positions in the figure above.

Congratulations—You have finished assembling your electronic drum kit!

Setup for Left-handed Drummers

Assemble the drum kit referring to the illustration.

Two of the joints should be placed differently from this setup for right-

handed drummers.

The sticker on each of the snake cable’s plugs indicates the name of the corresponding pad.

For the kick pad KP65 in the DTX432K and DTX452K, use the OUT>DTX jack. No sound will be played when the PAD>IN jack is

used.

Excessive bending can damage the cables. Ensure, therefore, that they are not bent at an extreme angle when wrapped around the

cord clip.

Step 14

RIDE

SNR

KICK

HHC

TOM3

TOM2 TOM1

KICK

HHC

RIDESNRHH

KICKHHCHHCRRIDETOM3TOM2TOM1SNR

TOM2TOM1CR TOM3 KICK HHC

DTX402K

Trigger input jacks on the drum module

Nine-channel snake cable

NOTE

NOTICE

Fully assembled drum kit (DTX452K shown)

Right-handed Left-handed

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Setting Up for Sound

1. Ensure that your drum module is turned off (i.e., none

of the buttons are lit).

2. Insert the AC adaptor’s DC plug into the

[ ] connector on the bottom panel of

the module.

3. Hook the AC adaptor cord around the cord clip to pre-

vent it from being accidentally pulled out.

4. Plug the adaptor’s AC power cord into an AC wall

socket or another electrical outlet.

Your drum module does not have built-in speakers. In order

to hear it, therefore, you will need to connect headphones or

monitor speakers via the [PHONES/OUTPUT] standard

stereo-audio jack. You can adjust the output volume using

the [VOLUME] buttons on the control panel.

You can connect a portable music player or another similar

source of audio to your drum module via the [AUX IN]

(auxiliary input) stereo mini-jack. This makes it possible

to play along with your favorite tunes.

Connecting the Power

CAUTION

Excessive bending can damage the AC adaptor cord

and create a fire hazard. Ensure, therefore, that the

power cord is not bent at an extreme angle when

wrapped around the clip.

WARNING

• Use the specified AC adaptor (page 64) only. Using

the wrong AC adaptor can result in damage to the

instrument or overheating.

• When using the AC adaptor with a removable plug,

make sure to keep the plug attached to the AC adap-

tor. Using the plug alone can cause electric shock or

fire.

• Never touch the metallic section when attaching the

plug. To avoid electric shock, short circuit or dam-

age, also be careful that there is no dust between the

AC adaptor and plug.

Cord clip AC adaptor cord

Slide the plug as

indicated

Plug

The shape of the plug

differs depending on

your area.

Connecting Headphones or Speakers

The [PHONES/OUTPUT] jack is a stereo connector. You can con-

nect a 1/4" mono-audio jack to it, but in such a case, please be

sure to set the output to mono using the Stereo/Mono parameter

from Menu Mode (page 55).

CAUTION

To prevent hearing loss, avoid using headphones at a

high volume for extended periods of time.

Connecting a Music Player

• Whenever connecting other devices, ensure that the cables you

use have plugs that match the input or output connectors on

those devices.

• Before making connections, furthermore, you should also turn

the volume on the other devices fully down.

• When all connections have been made, use each device’s vol-

ume controller to balance its output with that of the drum mod-

ule.

NOTE

NOTICE

1/8" stereo-mini

to stereo-mini

cable

Portable music player,

etc.

Standard 1/4"

mono-audio jack

Powered speakers

Standard 1/4"

stereo-audio

jack

Headphones

Setting Up for Sound

Setup

DTX402K DTX432K DTX452K Owner’s Manual

1. If you have connected your drum module to other audio

devices such as powered speakers, ensure that the vol-

ume on all other devices is turned down fully.

2. Press the [ ] (Standby/On) button.

The drum module will turn on and its buttons will light

up.

1. If you have connected your drum module to other audio

equipment, ensure that the volume on all other devices

is turned down fully.

2. Press the [ ] (Standby/On) button.

The drum module will turn off and all button lights will

go out.

The Auto Power-Off function automatically turns off the

drum module after a certain period of inactivity. This helps

to save energy should you forget to turn it off yourself.

 Setting the Auto Power-Off Function

You can set the amount of time that the Auto Power-Off

function will wait before turning off the drum module. For

details, see the description of the Auto Power-Off Time

parameter from Menu Mode (page 54).

 Quickly disabling Auto Power-Off

To quickly disable the Auto Power-Off function, turn on the

drum module while holding down the number button [1].

The function will remain off until you set a new Auto

Power-Off time.

Straight out of the box, your drum module already contains

a wide range of pre-programmed drum kits and songs.

These default settings—collectively known as the Factory

Reset—can be conveniently restored at any time if you have

accidentally overwritten them or wish to delete all of your

own settings. To do so, use the Factory Reset function as

follows.

1. Press the [ ] (Standby/On) button and verify that

the drum module turns off.

2. Turn on the drum module while holding down the

VOLUME[+] button and the VOLUME[–] button.

The drum module’s lights will flash and the Factory

Reset will be restored.

Turning On the Drum Module

Connect the hi-hat controller before turning on the drum

module. Please do not turn the drum module on with the hi-

hat controller depressed. The drum module can not identify

the type of pedal properly and it causes that the kick may

produce much smaller sound than expected.

Turning Off the Drum Module

The drum module automatically stores all current settings

before it turns off. For this reason, please do not unplug the

AC adaptor until all button lights have gone out.

Auto Power-Off

The drum module automatically stores all current settings before

it turns off.

NOTE

NOTICE

NOTE

• In certain modes of operation, the Auto Power-Off function will

not turn off the drum module when the set time has elapsed. We

recommend, therefore, that you always turn off the drum module

manually when you are finished using it.

• If you expect the drum module to be inactive for a certain length

of time while connected to other audio equipment, we recom-

mend that you turn the volume on the other equipment fully

down. Alternatively, you can disable the Auto Power-Off function

to ensure that the drum module stays on.

• Settings for the Auto Power-Off function do not represent exact

times and there may be some variation.

• By default, the Auto Power-Off time is set to 30 minutes.

Restoring the Default Settings

(Factory Reset)

When you restore the Factory Reset as described below, any

changes you have made to parameters will be lost. Before pro-

ceeding, therefore, you should ensure that they contain no irre-

placeable settings.

NOTICE

NOTE

Hold

NOTICE

Hold

Setup

DTX402K DTX432K DTX452K Owner’s Manual

Panel Controls & Functions

 Drum module

z Mode switch

• Press this switch to switch Play Mode and Training

Mode. (pages 26, 31)

• Hold down this switch to select Menu Mode. (page 41)

x [DRUM ON/OFF] button (page 28)

Use this button to mute and unmute drum parts from a

practice drum pattern.

c [] button

• Use this button to start and stop songs. (page 27)

• In Training Mode, it is also used to start and stop train-

ing sessions. (page 31)

v [ ] (metronome) button (page 29)

• Use this button to start and stop the built-in metro-

nome.

• In Training Mode, it is also used to start and stop train-

ing sessions.

b [TEMPO] buttons (page 30)

Use these buttons to increase or decrease the tempo in

steps of one BPM.

*: In Menu Mode, it is also used to increase or decrease set-

tings.

n [VOLUME] buttons (page 26)

Use these buttons to adjust the overall volume of the

drum module. Press the [+] button to increase it and the

[–] button to decrease it.

m [ ] (Standby/On) button (page 22)

Use this button to turn the drum module on and off.

, Number buttons

• Use these buttons to select music categories and train-

ing types. (pages 27, 31)

• They are also used to enter a tempo directly. (page 30)

• In Menu Mode, they are used to select settings. (page

41)

• Also in Menu Mode, they are used to enter setting val-

ues directly. (page 41)

Control Panel

Panel Controls & Functions

Setup

DTX402K DTX432K DTX452K Owner’s Manual

. [USB TO HOST] terminal (page 58)

Connect a computer or smart device such as an iPhone or

iPad to send and receive digital signals (audio and

MIDI).

Additional parts are required for connecting an iPhone

or iPad. For more information, refer to “iPhone/iPad

Connection Manual” (PDF).

⁄0 [AUX IN] jack (page 21)

The Auxiliary Input stereo mini-jack is used to input

audio from an external source. For example, you can use

this jack to connect a portable music player or another

similar device and play along with your favorite tunes.

⁄1 [PHONES/OUTPUT] jack (page 21)

Use this standard stereo-audio jack to connect head-

phones, an amplifier, a mixer, or other similar equip-

ment.

⁄2 Cord clip (page 21)

Wrap the AC adaptor cord around this clip to prevent

accidental unplugging during use.

⁄3 [ ] connector (page 21)

Use this connector for the AC adaptor that came with

your drum module.

⁄4 Trigger input jacks (page 20)

Use these jacks to connect the snare, tom, and cymbal

pads.

⁄5 [HI-HAT CTL] jack (page 20)

The Hi-hat Control jack is used to connect a hi-hat con-

troller.

⁄6 [KICK/PAD] jack (page 20)

Use this jack to connect a kick pad or pedal. By connect-

ing a KP65, you can add another pad using the PAD >

IN jack on the KP65 (page 57).

Bottom Panel

. ⁄0 ⁄1 ⁄2 ⁄3

Top Panel

⁄5 ⁄6⁄4

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

Playing Techniques

If using a TP70S Snare Pad with the DTX452K, you will be

able to produce three distinct sounds (i.e., head, open rim,

and closed rim) depending on where you strike it, much the

same as if you were playing an acoustic snare.

 Head shots

Hitting the main surface of the pad produces a head shot

sound.

 Open rim shots

Hitting the open-rim zone produces an open rim-shot

sound.

 Closed rim shots (cross sticking)

Hitting the closed-rim zone produces a closed rim-shot

sound.

 Open/close

• You can produce an open hi-hat sound by striking the

hi-hat pad with the hi-hat controller’s pedal not

depressed.

• You can produce a closed hi-hat sound by striking the

hi-hat pad with the hi-hat controller’s pedal depressed.

• If using an HH65 Hi-hat Controller with the

DTX432K and DTX452K, you can operate the pedal

to recreate the sound of a closing hi-hat.

 Foot closed

You can depress the hi-hat controller’s pedal to create a

foot-close sound without having to strike the hi-hat pad.

 Hi-hat splash

Depressing the hi-hat controller’s pedal and then imme-

diately releasing it produces a hi-hat splash sound.

 Choke

You can immediately mute a sound by choking (pinch-

ing) the cymbal’s edge with your hand after hitting the

cymbal. The Choke function only works when you

grasp in the sensor area.

Snare Pad

Closed rim shots

(Rim 2)

Head shotsOpen rim shots (Rim 1)

Hi-hat Cymbal

If using an HH40 Hi-hat Controller with the DTX402K, the

velocity is fixed regardless of how strongly or softly the hi-hat

controller’s pedal is depressed. For adjusting the fixed veloc-

ity value, see the description of the Foot Close Velocity

parameter from Menu Mode (page 47).

Crash Cymbal

NOTE

Sensor (bumps)

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

Performing with a Selected Music Category

The drum module comes with ten different music categories. When you select a music category, the

corresponding “kit” (referring to a full set of drum-sound assignments for all of the pads) and song

will be automatically selected.

1. Press the Mode switch to turn the “PLAY” light on

(Play Mode).

2. Select a music category by pressing the corresponding

number button [1] to [10].

The selected number button will light up and the corre-

sponding drum or percussion kit will be automatically

selected.

3. Play the pads and see how the kit sounds.

Using the following procedure, you can change the sensitiv-

ity of a kit—that is, how the drum sounds change depending

on how hard you strike the pads. Sensitivity can be adjusted

to ten different levels.

While holding the Mode switch, press either the VOL-

UME[+] or VOLUME[–] button.

• Each time you press the VOLUME[+] button, you

increase the sensitivity by one level. This means that

louder sounds can be more easily produced with softer

drumming.

• Each time you press the VOLUME[–] button, you

decrease the sensitivity by one level. This means that

louder sounds can only be produced by drumming hard.

Selecting a Music Category

For detailed information on the ten preset music categories,

see the Data List section (page 62).

NOTE

Adjusting Kit Sensitivity

• The selected sensitivity is common to the drum module’s ten

kits.

• If you wish to set sensitivities on an individual pad basis, see the

descriptions of the Trigger Settings parameters from Menu Mode

(page 48).

Hold

sensitive pads

Less

sensitive pads

More sensitive

pads

Less sensitive

pads

NOTE

Performing with a Selected Music Category

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

1. Press the Mode switch to turn the “PLAY” light on.

2. Select a music category by pressing the corresponding

number button [1] to [10].

The selected number button will light up and the corre-

sponding song will be automatically selected.

3. Press the [ ] button to start the song.

4. Play the pads with the song.

5. To stop the song, press the [ ] button once again.

While holding the [] button, press either the VOL-

UME[+] or VOLUME[–] button.

• Each time you press the VOLUME[+] button, you

increase the song volume by one.

• Each time you press the VOLUME[–] button, you

decrease the song volume by one.

Performing with a Song

The score (PDF) is available at the Yamaha website:

https://download.yamaha.com/

After accessing the Support website (and clicking on “Man-

ual Library”), enter the appropriate model name.

If you wish to mute the programmed drum parts and hear

only the song parts, press the [DRUM ON/OFF] button. To

unmute the drum parts, press the [DRUM ON/OFF] button

once again.

NOTE

Adjusting the Song Volume

The set volume is common to the drum module’s ten songs.

Hold

Higher song

volume

Lower song

volume

NOTE

Performing with a Selected Music Category

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

If you press the [DRUM ON/OFF] button while playing a

song, the drum parts from the song will be muted—that is,

their volume will be reduced to zero. If, however, you would

like the drum parts to be slightly audible in this type of situ-

ation, you can adjust the muted volume as described below.

1. Press the [ ] button to start the song.

2. Press the [DRUM ON/OFF] button to mute the drum

parts.

The button is unlit when the drum part is muted, and is

lit when the drum part is played (not muted).

3. While holding the [DRUM ON/OFF] button, press

either the VOLUME[+] or VOLUME[–] button.

• -Each time you press the VOLUME[+] button, you

increase the volume of the muted drums by one.

• Each time you press the VOLUME[–] button, you

decrease the volume of the muted drums by one.

By pressing the [DRUM ON/OFF] button once again, you

can unmute the drum parts and restore their normal vol-

umes.

Using apps compatible with the drum module, you can eas-

ily import a MIDI song on your drum module.

For details on compatible smart devices and applications,

refer to the web page below.

For more information on how to connect, refer to the

“iPhone/iPad Connection Manual” (PDF) on the web page

below.

https://download.yamaha.com/

After accessing the Support website (and clicking on

“Manual Library”), enter the appropriate model name.

Adjusting the Volume of Muted Drum

Parts

Hold

Maximum

muted volume

Minimum

muted volume

Importing a MIDI song

• For deleting the imported MIDI song, see the description of the

Delete Song parameter from Menu Mode (page 55).

• To eliminate the risk of interference due to noise by your smart

device when used in combination with the drum module, turn on

the Airplane Mode and then turn on Wi-Fi.

Be sure to place your smart device on a stable surface to prevent

it from falling over and being damaged.

NOTE

NOTICE

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

Using the Metronome

Playing your electronic drum kit along with the built-in metronome is a great way to perfect your

rhythm.

• Press the [] button to turn on the metronome.

• Press the [] button once again to turn it off.

To adjust the volume of the metronome, press and hold the

[] button, and then press either the VOLUME[+] or

VOLUME[–] button.

• Each time you press the VOLUME[+] button, you

increase the metronome volume by one.

• Each time you press the VOLUME[–] button, you

decrease the metronome volume by one.

Whenever necessary, you can confirm the drum module’s

current tempo from the flashing pattern of the number but-

ton lights and the voice guidance.

The larger the value, the faster the tempo becomes.

Press either the TEMPO[+] or TEMPO[–] button once.

Press and hold the [] button.

Each digit of the tempo will be flashed in sequence.

Example:

When the tempo is 108 BPM, the number button lights will

flash [1][0][8].

Starting and Stopping the Metronome

Adjusting the Metronome Volume

Hold

Higher metro-

nome volume

Lower metro-

nome volume

Confirming Tempo

If you wish to turn off the voice guidance function, see 7-1. Voice

Guidance Volume (page 53).

NOTE

Using the Metronome

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

The following three methods are available when you want to

change the tempo.

 Increasing or decreasing using the

TEMPO[+] or TEMPO[–] button

• Each time you press the TEMPO[+] button, you

increase the metronome BPM by one.

• Each time you press the TEMPO[–] button, you

decrease the metronome BPM by one.

 Directly inputting a BPM using the number

buttons

1. While holding the [ ] button, enter the BPM using

the number buttons.

The drum module will speak the input tempo to you

(in English).

Example: Setting a tempo of 138 BPM

Press the number buttons in the sequence

[1][3][8].

2. After entering all necessary digits, remove your fin-

ger from the [ ] button.

The drum module will speak the new tempo to you

(in English).

 Tapping the tempo on the pads

1. While holding the [ ] button, strike a pad at least

three times at the desired tempo.

2. Remove your finger from the [ ] button.

The drum module will speak the new tempo to you

(in English).

The following metronome-related settings can be made in

Menu Mode. For details, see the description of the Metro-

nome Settings parameter group from Menu Mode (page 42).

• Metronome pattern

• Metronome length in beats

• Metronome sound

• Number-button lighting pattern when using the metro-

nome

Adjusting the Tempo

 Increasing or decreasing using the TEMPO[+]

or TEMPO[–] button

 Directly inputting a BPM using the number

buttons

 Tapping the tempo on the pads

• The drum module supports tempos between 30 and 300 BPM.

• If you select a different song (page 27) after adjusting the tempo,

the selected song’s tempo will be used for the metronome.

NOTE

Hold

• Number button [10] is used to enter the value zero. You

cannot use it to enter the number ten.

Example: Setting a tempo of 110 BPM

Press the number buttons in the sequence

[1][1][10].

You cannot do this by pressing [1][10].

• There is no need to enter a zero first in order to set a

two-digit tempo.

Example:

To set a tempo of 72 BPM, simply press the num-

ber buttons in the sequence [7][2]. You do not

need to press [10][7][2].

• Whenever the drum module is speaking the tempo, you

can enter a new tempo directly using the number but-

tons but without having to hold down the [ ] button.

Instead of using a pad, you can also tap the tempo by

pressing the TEMPO[+] or TEMPO[–] button at least

three times.

Other Settings

NOTE

Hold

NOTE

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

Practicing in Training Mode

With ten different types of training available, you can learn how to play drums and master them in an

enjoyable way.

Before starting, please select your desired music category.

1. Press the Mode switch to turn the “PLAY” light on.

2. Select a music category by pressing the corresponding

number button.

You can make detailed settings for Training, such as the

practice timer and the difficulty level in Menu Mode (page

41).

For the following training exercises, the drum module eval-

uates your ability on a scale of one to ten and displays the

results using the number buttons.

• Rhythm Gate • Song Score Gate

• Dynamic Gate • Change Up

Number button [10] represents the highest score, while

number button [1] represents the lowest. In addition, the

Voice Guidance announces the results of scoring using the

five levels shown below. Try your best to get a high score!

To start a different exercise, you need to

reenter the training mode.

1. Press the Mode switch to turn the

“PLAY” light on (Play Mode).

2. Press the Mode switch again to turn the

“TRAINING” light on (Training Mode).

Basic training

Working on your rhythm:

Rhythm Gate (2 types) . . . . . . . . . . . . page 32

Measure Break . . . . . . . . . . . . . . . . . . page 36

Change Up . . . . . . . . . . . . . . . . . . . . . page 37

Playing with dynamics:

Dynamic Gate . . . . . . . . . . . . . . . . . . . page 33

Playing as fast as you can:

Fast Blast. . . . . . . . . . . . . . . . . . . . . . . page 39

Practicing by parts:

Part Mute. . . . . . . . . . . . . . . . . . . . . . . page 38

Recording your play:

Recorder . . . . . . . . . . . . . . . . . . . . . . . page 40

Advanced training

— Going on to mastery after Basic training! —

Playing along with a song:

Song Part Gate . . . . . . . . . . . . . . . . . . page 34

Song Score Gate. . . . . . . . . . . . . . . . . page 35

Before Training

Detailed Training settings

After Training

Switching to a different exercise

Better scores

Try again Great

Fantastic

Good Excellent

Practicing in Training Mode

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

1. RHYTHM GATE

2. RHYTHM GATE

1. Press the Mode switch to turn the “TRAINING” light

on (Training Mode).

2. Press number button [1] or [2] to select Rhythm Gate.

[1] is for a sixteenth-note rhythm exercise and [2] is for

a triplet rhythm exercise.

The [] button and [] button flash, indicating

that the exercise is on standby.

3. If you press the [ ] button, the current song will be

used for the exercise. If you press the [ ] button, the

metronome will be used.

4. Play the pads as rhythmically “tight” as you can along

with the song or the metronome.

5. To end the exercise, press the button used to start it in

Step 3.

Your score will be displayed. (For details, see page 31.)

Working on your rhythm:

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

1. RHYTHM GATE, 2. RHYTHM GATE

Rhythm Gate is an exercise for improving your timing along with a song or the metronome. When you strike with

perfect timing, the number buttons [5] and [6] flash together. When you strike too early or too late, no sound is

produced. Using Rhythm Gate can greatly help you improve your sense of rhythm!

Struck early Struck late

Perfect Timing

(flash together)

Sound produced (half-lit)

Timing of current strike (flashes)

When the “TRAINING” light is ON, press the Mode switch to

turn on the “PLAY” button, and then press the Mode switch

again to turn on the “TRAINING” light.

Please change the beats of the metronome, as needed.

Procedure

NOTE

TIPS

• Pressing the number buttons [2] to [9] while the

exercise is on standby or during the exercise allows

you to adjust the sensitivity to your timing accuracy

in striking the pads and making sound. The nar-

rower the range, the higher the difficulty level.

• The direction of the timing indicators for showing

“too slow” to “too fast” can be reversed. (Menu

Mode “Rhythm Gate indicator flipped”; page 52.)

• The exercise time can be adjusted. (Menu Mode

“Timer”; page 51.)

• You can set whether the pads produce sound

whenever they are struck or only when they are

struck exactly in time. (Menu Mode “Ignore Timing”;

page 51.)

Press [2] or [9].

Press [3] or [8].

Press [4] or [7].

Press [5] or [6].

Easy

Difficulty

level

Hard

1 2 3 4 5 6 7 8 9 10

12345678 910

Practicing in Training Mode

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

3. DYNAMIC GATE

1. Press the Mode switch to turn the “TRAINING” light

on.

2. Press number button [3] to select Dynamic Gate.

The [ ] button flashes, indicating that the exercise

is on standby.

3. Strike the desired pad for practicing.

4. Press number buttons [1] or [10] to select the level.

[1] to [3] is “weak,” [4] to [7] is “normal,” and [8] to

[10] is “strong.”

The number buttons in the selected level become half

lit.

5. Press the [] button to start the exercise.

6. Strike the pad you chose in Step 4 with proper dynam-

ics.

7. To end the exercise, press the [ ] button.

Your score will be displayed. (For details, see page 31.)

Playing with dynamics:

3. DYNAMIC GATE

Dynamic Gate is an exercise for playing pads with proper dynamics. Your aim is to control three levels: Weak,

Normal and Strong. When you strike with the wrong dynamics, it will not produce any sound. How accurately you

strike with the proper dynamics is evaluated at the end of the exercise. Once you master Dynamic Gate, you will

be a skillful drummer at controlling dynamics depending on the situation!

Strength of current strike (flashes)

Weak Normal Strong

When the “TRAINING” light is ON, press the Mode switch to

turn on the “PLAY” button, and then press the Mode switch

again to turn on the “TRAINING” light.

Procedure

NOTE

Weak Normal Strong

TIPS

• The range of the dynamics can be adjusted. (Menu

Mode “Dynamic Gate Low Limit” and “Dynamic

Gate High Limit”; page 52.)

• The exercise time can be adjusted. (Menu Mode

“Timer”; page 51.)

Practicing in Training Mode

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

4. SONG PART GATE

1. Press the Mode switch to turn the “TRAINING” light

on.

2. Press number button [4] to select Song Part Gate.

The [ ] button flashes, indicating that the exercise

is on standby.

3. Press the corresponding number button to select the

way to practice

4. Press the [ ] button to start the

exercise.

The song will be played.

5. Play the practice drum pattern on the

pads.

6. To end the exercise, press the [] button.

Your score will be announced by the voice guidance after

every time the practice drum pattern is repeated. The total

score is not evaluated after ending the exercise.

Playing along with a song:

4. SONG PART GATE

Song Part Gate is an advanced exercise for playing actual

drum patterns along with a part of a song. For example,

you can practice just the fill-in part in the song, or only the

hand parts of the basic drum pattern of the song. Before

working on Song Part Gate, it would be better to master

the other basic training programs. Then once you master

Song Part Gate, you can confidently work on Song Score

Gate (page 35) for playing the entire song!

The score (PDF) is available at the Yamaha website:

https://download.yamaha.com/

After accessing the Support website (and clicking on “Man-

ual Library”), enter the appropriate model name.

NOTE

When the “TRAINING” light is ON, press the Mode switch to

turn on the “PLAY” button, and then press the Mode switch

again to turn on the “TRAINING” light.

The available exercises may differ depending on the current

music category. For details, refer to the Score (PDF).

Procedure

NOTE

Scoring

TIPS

• The music category can be changed (by holding

down the corresponding number button).

• The volume of the practice pattern can be adjusted.

(While holding down the [ ] button, press the

VOLUME[+]/[–] button.)

• You can mute specific parts of the practice drum

pattern.

- The mute settings are effective while the [DRUM

ON/OFF] button is half-lit.

- While the song is being played, strike the pad

corresponding to the part you wish to mute. The

selected part will be muted.

- If the pad corresponding to the muted drum part

is not struck for certain period of time, it will be

automatically unmuted.

- Press the [DRUM ON/OFF] button (so that it is

fully lit) to end the mute settings.

• The exercise time can be adjusted. (Menu Mode

“Timer”; page 51.)

• The difficulty of the exercise can be adjusted.

(Menu Mode “Difficulty Level”; page 51.)

• You can set whether the pads produce sound

whenever they are struck or only when they are

struck exactly in time. (Menu Mode “Ignore Timing”;

page 51.)

Practicing in Training Mode

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

5. SONG SCORE GATE

1. Press the Mode switch to turn the “TRAINING” light

on.

2. Press number button [5] to select Song Score Gate.

The [ ] button flashes, indicating that the exercise

is on standby.

3. Press the [ ] button to start the exercise.

4. Play the drum pattern on the pads.

After you play the entire song, your score will be dis-

played. (For details, see page 31.)

5. To stop the exercise, press the [ ] button.

When you stop the exercise before the end of the song,

the score for your exercise will not be shown.

Playing along with a song:

5. SONG SCORE GATE

Song Score Gate is a final exercise for playing actual

drum patterns along with an entire song. Before work-

ing on Song Score Gate, we recommend that you first

master Song Part Gate (page 34) as much as possi-

ble—and get you on your way to be a great drummer!

The score (PDF) is available at the Yamaha website:

https://download.yamaha.com/

After accessing the Support website (and clicking on

“Manual Library”), enter the appropriate model name.

NOTE

When the “TRAINING” light is ON, press the Mode switch to

turn on the “PLAY” button, and then press the Mode switch

again to turn on the “TRAINING” light.

Procedure

NOTE

TIPS

• You can change the music category (by pressing a

corresponding number key).

• The volume of the song can be adjusted. (While

holding down the [ ] button, press the VOL-

UME[+]/[–] button.)

• You can mute specific parts of the practice drum

pattern.

- The mute settings are effective while the [DRUM

ON/OFF] button is half-lit.

- While the song is being played, strike the pad

corresponding to the part you wish to mute. The

selected part will be muted.

- If the pad corresponding to the muted drum part

is not struck for certain period of time, it will be

automatically unmuted.

- Press the [DRUM ON/OFF] button (so that it is

fully lit) to end the mute settings.

• The difficulty of the exercise can be adjusted.

(Menu Mode “Difficulty Level”; page 51.)

• You can set whether the pads produce sound

whenever they are struck or only when they are

struck exactly in time. (Menu Mode “Ignore Timing”;

page 51.)

Practicing in Training Mode

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

6. MEASURE BREAK

1. Press the Mode switch to turn the “TRAINING” light

on.

2. Press number button [6] to select Measure Break.

The [] button flashes, indicating that the exercise is

on standby.

3. Press the [ ] button to start the exercise.

Four measures will be repeatedly played back. (The first

to third measures are with the metronome and the fourth

measure is without the metronome.) The number button

flashes along with playback of the corresponding mea-

sure.

4. Play the pads.

5. To end the exercise, press the [] button.

How exactly you strike the first beat of the measure after the

break will be announced by the voice guidance after every

four measures are repeated. The total score is not evaluated

after ending the exercise.

Working on your rhythm:

6. MEASURE BREAK

Measure Break is an exercise for keeping a steady tempo without the metronome. How accurately you strike the

first beat of the measure after the break is evaluated. Once you master Measure Break, you can keep a steady

tempo even after breaks or fill ins.

Evaluate

the first beat

With Metronome (fully-lit) Without Metronome (half-lit)

When the “TRAINING” light is ON, press the Mode switch to

turn on the “PLAY” button, and then press the Mode switch

again to turn on the “TRAINING” light.

Procedure

NOTE

Scoring

TIPS

• The total number of measures can be changed to

any number from 2 to 10.

While the exercise is on standby or during the exer-

cise, hold down the number button until the key is

half-lit.

For example, to repeat ten measures, hold down

the number button [10] until the number button [10]

is half-lit.

• The number of measures with the metronome clicks

can be changed.

While the exercise is on standby or during the exer-

cises, press the number button corresponding to

the number of measures you would like to set. Keep

in mind, however, that the last measure of this exer-

cise is always set to be without the metronome.

For example, by pressing the number button [6]

while the total number of measures is set to 10,

measures 1 to 6 are counted with the metronome,

and measures 7 to 10 are without the metronome.

• The exercise time can be adjusted. (Menu Mode

“Timer”; page 51.)

Practicing in Training Mode

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

7. CHANGE UP

1. Press the Mode switch to turn the “TRAINING” light

on.

2. Press number button [7] to select Change Up.

The [ ] button flashes, indicating that the exercise

is on standby.

3. Press the [ ] button to start the exercise.

The practice rhythm and the metronome start to play,

and the rhythm changes after every two measures.

4. Play the practice rhythm on the pads.

5. To end the exercise, press the [] button.

Your score will be displayed. (For details, see page 31.)

Working on your rhythm:

7. CHANGE UP

Change Up is an exercise for playing seven different rhythms that change every two measures. How well you

maintain good timing along with the rhythms is evaluated. Try your best to keep a steady tempo—even when the

rhythms change!

33 6

Rhythm

When the “TRAINING” light is ON, press the Mode switch to

turn on the “PLAY” button, and then press the Mode switch

again to turn on the “TRAINING” light.

Procedure

NOTE

TIPS

• The volume of the practice rhythm can be adjusted.

(While holding down the [ ] button, press the

VOLUME[+]/[–] button.)

• The practice rhythm can be muted. (Press the

[DRUM ON/OFF] button. To unmute, press it

again.)

• You can skip among the seven rhythms as you

practice by pressing the corresponding number

button while the exercise is on standby or during

the exercise, as shown in the example below. The

number button corresponding to the rhythm to be

skipped is half lit.

• By default, each rhythm changes after every two

measures. The number of measures can be

changed by pressing [10] several times. (Four mea-

sures when [10] is half lit, one measure when [10] is

fully lit, and two measures (default) when [10] is off.)

• The exercise time can be adjusted. (Menu Mode

“Timer”; page 51.)

• The difficulty of the exercise can be adjusted.

(Menu Mode “Difficulty Level”; page 51.)

• You can set whether the pads produce sound

whenever they are struck or only when they are

struck exactly in time. (Menu Mode “Ignore Timing”;

page 51.)

33 6

Practicing in Training Mode

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

8. PART MUTE

1. Press the Mode switch to turn the “TRAINING” light

on.

2. Press number button [8] to select Part Mute.

The [ ] button flashes, indicating that the exercise

is on standby.

3. To mute drum parts/instrument parts, press the corre-

sponding number buttons [1] to [5] or [9] to [10]. The

number button of the muted part will be turned off (see

illustration above). To unmute, press the number but-

ton again. The number button lights up.

4. Press the [ ] button to start the exercise.

5. Play along the song on the pads.

6. To end the exercise, press the [] button.

Practicing by parts:

8. PART MUTE

Part Mute is an exercise which you can mute any or all of the drum parts (such as snare and kick) and the instru-

ment parts (non-drum parts) from a song. You can select the drum parts/instrument parts to be muted by pressing

the corresponding number buttons. Part Mute can be useful in many ways—for example, for practicing only the

snare part of a rhythm, or for tightening up your rhythm section skills by practicing only with a bass guitar sound.

Keep in mind that this exercise is not scored.

Hi-hat Kick Cymbal Other song parts

Bass part Snare Tom

Drum parts

(off) (off)

When the “TRAINING” light is ON, press the Mode switch to

turn on the “PLAY” button, and then press the Mode switch

again to turn on the “TRAINING” light.

Procedure

NOTE

TIPS

Drum parts can be muted by striking the pads.

- Press the [DRUM ON/OFF] button (so that it is

half-lit).

- Strike the pad corresponding to the part from the

practice drum pattern you wish to mute. The

selected part will be muted and the corresponding

number button will be half lit.

- If the pad corresponding to the muted drum part is

not struck for certain period of time, it will be auto-

matically unmuted and the corresponding number

button will light up.

- Press the [DRUM ON/OFF] button (so that it is

fully lit) to end the mute settings.

If the part is already muted (the corresponding number but-

ton is turned off), the pad remains muted.

NOTE

Practicing in Training Mode

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

9. FAST BLAST

1. Press the Mode switch to turn the “TRAINING” light

on.

2. Press number button [9] to select Fast Blast.

The [ ] button flashes, indicating that the exercise

is on standby.

3. Press the [ ] button to start the exercise.

The timer will start when you strike the first pad.

4. Strike pads as fast as possible.

When the training has ended, your score will be dis-

played.

5. To stop the exercise, press the [ ] button.

For example, if your score was 480, the number buttons

would flash [4] – [8] – [10].

• Your score will be announced by the voice guidance (in

English) as well.

• To check your score once again, press any of the num-

ber buttons [1] to [10].

Playing as fast as you can:

9. FAST BLAST

Fast Blast is an exercise for striking pads as fast as possible within a time limit (60 seconds). The half lit number

buttons indicates the remaining time. The exercise ends when the number buttons are all turned off. The number

of times you have struck will be shown by using the number buttons and also announced by the voice guidance.

Try practicing your fast drumming skills as if it were a game!

(half-lit)

When the “TRAINING” light is ON, press the Mode switch to

turn on the “PLAY” button, and then press the Mode switch

again to turn on the “TRAINING” light.

Procedure

NOTE

Scoring

TIPS

The time limit can be adjusted. (Menu Mode “Fast

Blast Timer”; page 53.)

Practicing in Training Mode

Basic Techniques

DTX402K DTX432K DTX452K Owner’s Manual

10. RECORDER

1. Press the Mode switch to turn the “TRAINING” light

on.

2. Press number button [10] to select Recorder.

The [ ] button flashes, indicating that recording is

set to standby.

3. Play the pad, and the recording starts automatically.

4. When you finish your performance, leave all pads with-

out striking for certain period of time.

The recording will be automatically stopped and the

recorded performance will be played back.

5. To end the exercise, press the Mode switch.

Recording your play:

10. RECORDER

Recorder allows you to easily record your performances. You can

use those recordings not only for listening back and checking your

progress, but also for playing along with yourself! Keep in mind

that this training is not scored.

When the “TRAINING” light is ON, press the Mode switch to

turn on the “PLAY” button, and then press the Mode switch

again to turn on the “TRAINING” light.

Procedure

NOTE

TIPS

• You can record your performance along with a

song. (Press the [ ] button while recording is

set to standby.)

• You can listen to the metronome click while record-

ing your performance. (Press the [] button while

recording is set to standby.)

• You can stop the playback of the recording by

pressing any number button. If you press any

number button again, the recording will be played

back from the beginning.

• The recorded performance is deleted when you exit

from the Training Mode.

• The beat setting for recording is “4 beats,” and can-

not be changed.

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

Setting Parameters using Menu Mode

Menu Mode is used to set drum-module parameters and functions, which are arranged into the follow-

ing seven groups.

1. Hold down the Mode switch to turn the “PLAY” and

“TRAINING” on (Menu Mode).

2. Press the number button corresponding to the group

containing the parameter you wish to set. (Parameter

groups are shown in the hierarchical list on the left.) To

select “1-2. Beats,” for example, press the number but-

tons in the order [1][2].

• When the setting value is less than 10

The number button of the current setting will be fully lit

and the selectable number buttons will be half-lit.

• When the setting value is more than 10

The number buttons flash continuously to indicate the

current setting. For example, when the current setting is

40, the number button lights will flash [4][10].

3. Enter the new setting.

• When the setting value is less than 10

Select a new setting using the corresponding number

button.

• When the setting value is more than 10

Press the TEMPO[+]/[–] button to increase and

decrease the setting values. If you take no action for a

while, the setting is automatically stored.

z Metronome Settings

1-1. Pattern ............................................................ Page 42

1-2. Beats.............................................................. Page 42

1-3. Sound............................................................. Page 42

1-4. Number Button Lighting Pattern ..................... Page 43

x Kit Settings

2-1. Pad Sound...................................................... Page 43

2-2. Pad Volume.................................................... Page 43

2-3. Pad Tuning..................................................... Page 44

2-4. Double Bass Drum......................................... Page 44

2-5. Reverb ........................................................... Page 44

c MIDI Settings

3-1. Local Control .................................................. Page 45

3-2. Note Number ................................................. Page 45

v Hi-hat Settings

4-1. Clutch Position................................................ Page 46

4-2. Splash Sensitivity........................................... Page 46

4-3. Foot Close Position........................................ Page 46

4-4. Foot Close Velocity ........................................ Page 47

4-5. Kick Velocity................................................... Page 47

b Trigger Settings

5-1. Pad Velocity Curve ......................................... Page 48

5-2. Crosstalk........................................................ Page 49

5-3. Snare Pad Type ............................................. Page 49

5-4. Pedal Type ..................................................... Page 50

5-5. Gain ............................................................... Page 50

5-6. Minimum Level............................................... Page 50

n Training Settings

6-1. Timer .............................................................. Page 51

6-2. Difficulty Level................................................ Page 51

6-3. Ignore Timing................................................. Page 51

6-4. Rhythm Gate Indicator Flipped ...................... Page 52

6-5. Dynamic Gate Low Limit ................................ Page 52

6-6. Dynamic Gate High Limit ............................... Page 52

6-7. Fast Blast Timer.............................................. Page 53

m Other Settings

7-1. Voice Guidance Volume.................................. Page 53

7-2. Operation Sound Volume ............................... Page 53

7-3. USB Audio Output Settings ............................ Page 54

7-4. USB Audio Output Gain ................................. Page 54

7-5. Auto Power-Off Time....................................... Page 54

7-6. Stereo/Mono................................................... Page 55

7-7. Initialize Kit...................................................... Page 55

7-8. Delete Song.................................................... Page 55

7-9. Revert to Last Power On ................................ Page 56

7-10. Factory Reset ............................................... Page 56

Basic Menu Mode Procedure

When the setting value is more than 10, you can also use the

number buttons to directly set parameters with numerical val-

ues. To enter the value 105, for example, press the number

buttons in the order [1][10][5]. [10] is used to enter the

value zero. You cannot use [10] to enter the number ten.

Selectable Settings

Current Setting

NOTE

Advanced Techniques

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

1-1. Pattern

You can set one of eight patterns for the drum module’s

metronome.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [1] to select the Metronome Set-

tings parameter group.

3. Press number button [1] to select the Pattern parame-

ter.

4. Select a new metronome pattern using the correspond-

ing number button [1] to [8].

1-2. Beats

You can set the metronome to between 1 and 9 beats in

length.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [1] to select the Metronome Set-

tings parameter group.

3. Press number button [2] to select the Beats parameter.

4. Select a new metronome length in beats using the corre-

sponding number button [1] to [9].

1-3. Sound

You can set the sound played by the metronome to, for

example, a standard click sound, a cowbell, a drumsticks

sound, or a spoken count.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [1] to select the Metronome Set-

tings parameter group.

3. Press number button [3] to select the Sound parameter.

z Metronome Settings

Steps:

Hold down the Mode switch  [1]  [1]  Setting

Number

button

Setting

[1]

[2]

[3]

[4]

[5]

3-2 Son Clave

[6]

2-3 Son Clave

[7]

3-2 Rumba Clave

[8]

2-3 Rumba Clave

Setting

3 3 3 3

Steps:

Hold down the Mode switch  [1]  [2]  Setting

Number button Setting

[1] 1 beat

[2] 2 beats

[3] 3 beats

[4] 4 beats

[5] 5 beats

[6] 6 beats

[7] 7 beats

[8] 8 beats

[9] 9 beats

Steps:

Hold down the Mode switch  [1]  [3]  Setting

Setting

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

4. Select a new metronome sound using the corresponding

number button [1] to [7].

1-4. Number Button Lighting Pattern

You can have number buttons [1] to [10] light up when play-

ing the metronome in Play Mode. Use the following proce-

dure to set the buttons’ lighting pattern.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [1] to select the Metronome Set-

tings parameter group.

3. Press number button [4] to select the Number Button

Lighting Pattern parameter.

4. Select a new lighting pattern using the corresponding

number button [1] to [3].

2-1. Pad Sound

You can change the sounds assigned to the current kit’s

pads. This makes it very easy to create your own unique

kits.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [2] to select the Kit Settings

parameter group.

3. Press number button [1] to select the Pad Sound

parameter.

4. Strike a pad to select it.

5. Enter a new drum-sound number using the TEMPO[+]/

[–] buttons. For a list of sounds and numbers, see the

Voice List (page 62).

2-2. Pad Volume

You can adjust the volume of the kit’s pads.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [2] to select the Kit Settings

parameter group.

3. Press number button [2] to select the Pad Volume

parameter.

4. Strike a pad to select it.

5. Enter a new volume using the TEMPO[+]/[–] buttons.

Number button Setting

[1] Metronome click 1

[2] Metronome click 2

[3] Cowbell

[4] Drumsticks

[5] Claves

[6] Spoken count 1

[7] Spoken count 2 (with measure number)

Steps:

Hold down the Mode switch  [1]  [4]  Setting

Number button Setting

[1] Off (no lighting)

[2] Pattern 1

[3] Pattern 2

Setting

x Kit Settings

Steps:

Hold down the Mode switch  [2]  [1]  Setting

Setting

1 to 287

Steps:

Hold down the Mode switch  [2]  [2]  Setting

Setting

0 to 127

Setting

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

2-3. Pad Tuning

You can adjust the panning of the current kit’s pads.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [2] to select the Kit Settings

parameter group.

3. Press number button [3] to select the Pad Panning

parameter.

4. Strike a pad to select it.

5. Enter a new tuning setting using the TEMPO[+]/[–]

buttons in 25 cent steps. The “cent” is a unit of measure

for musical intervals. 100 cents make up a semitone. A

value of 64 corresponds to normal pitch (0 cents).

2-4. Double Bass Drum

You can easily configure the drum module to produce a kick

drum sound when you operate the pedal connected to the

[HI-HAT CONTROL] trigger input jack. This convenient

function provides support for double bass drumming tech-

niques.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [2] to select the Kit Settings

parameter group.

3. Press number button [4] to select the Double Bass

Drum parameter.

4. Set the parameter using number button [1] or [2]. The

available settings are as follows.

2-5. Reverb

Reverb effects add a warm ambience to sounds, simulating

the complex reflections of actual performance spaces, such

as a concert hall or a small club. Use the following proce-

dure to select a reverb effect for the current kit.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [2] to select the Kit Settings

parameter group.

3. Press number button [5] to select the Reverb parame-

ter.

4. Select a reverb effect using the corresponding number

button [1] to [10].

Steps:

Hold down the Mode switch  [2]  [3]  Setting

Setting

16 (-1200 cents) to 64 (0 cent) to 112 (+1200 cents)

Steps:

Hold down the Mode switch  [2]  [4]  Setting

Setting

Number button Setting

[1] Off

[2] On

• While the Double Bass Drum function is enabled, you will be

unable to use the hi-hat controller plugged into the [HI-HAT

CONTROL] trigger input jack to simulate opening and closing of

the hi-hat.

• If using an HH40 Hi-hat Controller, you can adjust the kick veloc-

ity. For details, see 4-5. Kick Velocity (page 47).

Steps:

Hold down the Mode switch  [2]  [5]  Setting

Number button Setting

[1] Off

[2] Hall

[3] Studio

[4] Room 1

[5] Room 2

[6] Stage

[7] Small Stage

[8] Plate

[9] Early Reflection

[10] Gate Reverb

NOTE

Setting

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

3-1. Local Control

The Local Control parameter determines whether or not the

drum module’s internal tone generator will produce sounds

in response to playing of the pads or of songs. Normally,

this parameter is set to “On”, meaning that pads and songs

will generate sounds. When “Off” is selected, the tone gen-

erator is essentially disconnected from the pads and songs,

which will be unable to generate any sound. An “Off” set-

ting can prove highly useful when you wish to record your

drum performances as MIDI data on a sequencer or using

DAW software.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [3] to select the MIDI Settings

parameter group.

3. Press number button [1] to select the Local Control

parameter.

4. Set the parameter using number button [1] or [2]. The

available settings are as follows.

3-2. Note Number

You can set the MIDI note number that is output when each

of the pads is played.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [3] to select the MIDI Settings

parameter group.

3. Press number button [2] to select the Note Number

parameter.

4. Strike a pad to select it.

5. Enter a new note number using the TEMPO[+]/[–] but-

tons.

c MIDI Settings

Steps:

Hold down the Mode switch  [3]  [1]  Setting

Number

button

Setting Description

[1] Off

The internal tone generator does

not respond to pads and songs.

[2] On

The internal tone generator

responds to pads and songs.

• The drum module’s internal tone generator will continue to

respond to received MIDI data when Local Control is turned off.

• The drum module will continue to output drum performances as

MIDI data when Local Control is turned off.

Setting

NOTE

Steps:

Hold down the Mode switch  [3]  [2]  Setting

Setting

0 to 127

Note number settings are relevant only when you have connected

your drum module to a computer. For more details, refer to the

MIDI Reference Manual (PDF).

Setting

NOTE

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

4-1. Clutch Position

You can simulate the effect of changing the hi-hat’s clutch

position. The smaller the setting, the quicker an open hi-hat

sound will decay.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [4] to select the Hi-hat Settings

parameter group.

3. Press number button [1] to select the Clutch Position

parameter.

4. Enter a new clutch position using the TEMPO[+]/[–]

buttons.

4-2. Splash Sensitivity

You can set the degree of sensitivity for detecting hi-hat foot

splashes. The higher the value, the easier it will be to pro-

duce a foot-splash sound with the hi-hat controller. High

values may, however, result in splash sounds being uninten-

tionally produced when, for example, you operate the hi-hat

controller lightly as you keep time. It is a good idea, there-

fore, to set this parameter to “Off” if you do not want to play

foot splashes.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [4] to select the Hi-hat Settings

parameter group.

3. Press number button [2] to select the Splash Sensitiv-

ity parameter.

4. Enter a new splash sensitivity using the TEMPO[+]/[–]

buttons.

4-3. Foot Close Position

You can adjust the position at which the hi-hat switches

from open to closed when you operate the hi-hat controller.

The lower the value, the smaller the virtual opening between

the top and bottom hi-hats. Larger values increase the size

of the gap between the top and bottom cymbals, and this can

prevent foot close or foot splash sounds from being pro-

duced when you operate the pedal.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [4] to select the Hi-hat Settings

parameter group.

3. Press number button [3] to select the Foot Close Posi-

tion parameter.

4. Enter a new foot close position using the TEMPO[+]/

[–] buttons.

v Hi-hat Settings

Steps:

Hold down the Mode switch  [4]  [1]  Setting

Setting

0 to 64

Steps:

Hold down the Mode switch  [4]  [2]  Setting

Setting

0 to 127

Set this parameter to [0] in order to turn off foot splashes.

Steps:

Hold down the Mode switch  [4]  [3]  Setting

This parameter only has an effect when you are

using an HH65 Hi-hat Controller.

Setting

0 to 32

NOTE

Setting

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

4-4. Foot Close Velocity

You can adjust the velocity (or power) of foot-close sounds

produced using the hi-hat controller.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [4] to select the Hi-hat Settings

parameter group.

3. Press number button [4] to select the Foot Close

Velocity parameter.

4. Enter a new velocity using the TEMPO[+]/[–] buttons.

4-5. Kick Velocity

You can adjust the velocity (or power) of kick sounds pro-

duced using the hi-hat controller. In order for the Kick

Velocity parameter to have an effect, Double Bass Drum

must be set to “On” for the current kit (page 44).

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [4] to select the Hi-hat Settings

parameter group.

3. Press number button [5] to select the Kick Velocity

parameter.

4. Enter a new velocity using the TEMPO[+]/[–] buttons.

Steps:

Hold down the Mode switch  [4]  [4]  Setting

This parameter only has an effect when you are

using an HH40 Hi-hat Controller.

Setting

1 to 127

Setting

Steps:

Hold down the Mode switch  [4]  [5]  Setting

This parameter only has an effect when you are

using an HH40 Hi-hat Controller.

Setting

1 to 127

Setting

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

5-1. Pad Velocity Curve

You can select a velocity curve for individual pads. A veloc-

ity curve determines how the velocity (or power) of a sound

is affected by how hard you strike the pad.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [5] to select the Trigger Settings

parameter group.

3. Press number button [1] to select the Pad Velocity

Curve parameter.

4. Strike a pad to select it.

5. Enter a new velocity curve setting using the

TEMPO[+]/[–] buttons.

b Trigger Settings

Steps:

Hold down the Mode switch  [5]  [1]  Setting

Setting

1 to 25

Setting

Velocit y

Trigger input level

Velocity

Trigger input level

Velocity

Trigger input level

Velocit y

Trigger input level

Velocity

Trigger input level

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

5-2. Crosstalk

The term “crosstalk” refers to the output of spurious trigger

signals from a pad other than the one that was stuck as a

result of vibration or interference between pads. You can

adjust the Crosstalk parameter for individual pads to prevent

this phenomenon from occurring.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [5] to select the Trigger Settings

parameter group.

3. Press number button [2] to select the Crosstalk param-

eter.

4. Strike a pad to select it.

5. Enter a new setting (%) using the TEMPO[+]/[–] but-

tons. Larger values are more effective in preventing

crosstalk; however, they can also make it difficult to

play pads simultaneously during light drumming.

5-3. Snare Pad Type

You can specify the type of snare pad connected to your

drum module.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [5] to select the Trigger Settings

parameter group.

3. Press number button [3] to select the Snare Pad Type

parameter.

4. Select a new snare pad type using the corresponding

number button [1] to [6].

Steps:

Hold down the Mode switch  [5]  [2]  Setting

Setting

0 to 99

Setting

Steps:

Hold down the Mode switch  [5]  [3]  Setting

Number button Setting

[1]

Automatic identification

(only for [2] and [3])

[2] TP70S

[3]

Snare pad that comes with DX402K/

DTX432K

[4] XP-series pad

[5] TP70S reversed

[6] XP-series pad reversed

• When set to [1], the drum module will automatically identify the

type of snare pad that came with your electronic drum kit when it

is turned on. If you then press and hold number button [1], the

drum module will flash number button [2] or [3] to indicate the

result of automatic identification.

• Whenever you change the type of snare connected to the drum

module, please update this setting using the corresponding

number button [2] to [4]. For example, when you use the XP-

series pad, select [4].

• You can use setting [5] or [6] to switch (or reverse) the drum

sounds assigned to Rim 1 and Rim 2. This makes it easier for

left-handed drummers to configure their electronic drum kit.

Setting

NOTE

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

5-4. Pedal Type

Use the following parameter to specify the types of pedals

(i.e., hi-hat controller and kick) connected to your drum

module.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [5] to select the Trigger Settings

parameter group.

3. Press number button [4] to select the Pedal Types

parameter.

4. Select a new pedal type combination using the corre-

sponding number button [1] to [5].

5-5. Gain

You can set the gain level for trigger signals output from

individual pads. The higher the gain setting, the louder the

sounds produced by light drumming.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [5] to select the Trigger Settings

parameter group.

3. Press number button [5] to select the Gain parameter.

4. Strike a pad to select it.

5. Enter a new gain level using the TEMPO[+]/[–] but-

tons.

5-6. Minimum Level

When the strength with which you strike a pad is no more

than this level, the pad will not output a trigger signal in

response and no sound will be produced.

1. Hold down the Mode switch to activate Menu Mode.

2. Press number button [5] to select the Trigger Settings

parameter group.

3. Press number button [6] to select the Minimum Level

parameter.

4. Strike a pad to select it.

5. Enter a new setting (%) using the TEMPO[+]/[–] but-

tons.

Steps:

Hold down the Mode switch  [5]  [4]  Setting

Number

button

Setting

Hi-hat controller Kick pedal

[1] Automatic identification (only for [2] and [3])

[2] HH65 KP65

[3] HH40 KU100

[4] HH40 KP65

[5] HH65 KU100

• This parameter can normally be set to [1] (automatic identifica-

tion).

• When set to [1], the drum module will automatically identify the

type of pedal that came with your electronic drum kit when it is

turned on.

If you then press and hold number button [1], the drum module

will flash number button [2] or [3] to indicate the result of auto-

matic identification.

• Connect the hi-hat controller before turning on the drum module.

Please do not turn the drum module on with the hi-hat controller

depressed. The drum module can not identify the type of pedal

properly and it causes that the kick may produce much smaller

sound than expected.

• Whenever you change the type of hi-hat controller or kick pedal

connected to the drum module, please update this setting using

the corresponding number button [2] to [5].

Setting

NOTE

Steps:

Hold down the Mode switch  [5]  [5]  Setting

Setting

1 to 127

Steps:

Hold down the Mode switch  [5]  [6]  Setting

Setting

0 to 99 (%)

Setting

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

6-1. Timer

You can set the practice time for the following exercises in

Training Mode.

• Rhythm Gate

• Dynamic Gate

• Song Part Gate

• Measure Break

• Change Up

The timer begins counting at the start of an exercise, and

when the set time is reached, it automatically ends the exer-

cise.

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [6] to select the Training Set-

tings.

3. Press the number button [1] to select Timer.

4. Select your preferred practice time using the number

button [1] to [10].

6-2. Difficulty Level

You can set the level of training difficulty for the following

exercises.

• Song Part Gate

• Song Score Gate

•Change Up

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [6] to select the Training Set-

tings.

3. Press the number button [2] to select Difficulty Level.

4. Select your preferred difficulty level using the number

button [1] to [5]. The higher the level, the more diffi-

cult the training.

6-3. Ignore Timing

For the following trainings, you can set whether the pads

produce sound whenever they are struck or only when they

are struck exactly in time.

• Rhythm Gate

• Song Part Gate

• Song Score Gate

•Change Up

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [6] to select the Training Set-

tings.

3. Press the number button [3] to select Ignore Timing.

n Training Settings

Steps:

Hold down the Mode switch  [6]  [1]  Setting

Number button Settings

[1] Off

[2] 30 seconds

[3] 60 seconds

[4] 90 seconds

[5] 120 seconds

[6] 150 seconds

[7] 180 seconds

[8] 300 seconds

[9] 480 seconds

[10] 600 seconds

Setting

Steps:

Hold down the Mode switch  [6]  [2]  Setting

Setting

1 to 5

Steps:

Hold down the Mode switch  [6]  [3]  Setting

Setting

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

4. Select the setting for each drum pad using the number

buttons [1] to [5]. When set to producing a sound, the

pad will produce a sound whenever they are struck.

When set not to producing a sound, only pads played

exactly in time will produce a sound.

6-4. Rhythm Gate Indicator Flipped

For Rhythm Gate (page 32), the time indicator using the

number buttons can be reversed, according to your prefer-

ence. In the normal mode, “fast” is on the left. In the reverse

mode, “fast” is on the right.

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [6] to select the Training Set-

tings.

3. Press the number button [4] to select Rhythm Gate

Indicator Flipped.

4. Select the mode using the number button [1] or [2].

6-5. Dynamic Gate Low Limit

For Dynamic Gate (page 33), you can set the low limit (the

threshold value between “Weak” and “Normal”).

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [6] to select the Training Set-

tings.

3. Press the number button [5] to select Dynamic Gate

Low Limit.

4. Set the threshold value using the TEMPO[+]/[–] but-

tons.

6-6. Dynamic Gate High Limit

For Dynamic Gate (page 33), you can set the high limit (the

threshold value between “Normal” and “Strong”).

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [6] to select the Training Set-

tings.

3. Press the number button [6] to select Dynamic Gate

High Limit.

4. Set the threshold value using the TEMPO[+]/[–] but-

tons.

Number button Settings

[1] Hi-Hat

[2] Snare

[3] Kick

[4] Tom

[5] Cymbal

Steps:

Hold down the Mode switch  [6]  [4]  Setting

Number

button

Settings Description

[1]

Normal

mode

[2]

Reverse

mode

Produce a sound (fully lit)

Not producing a sound (half lit)

Setting

1 2 3 4 5 6 7 8 9 10

Fast Slow

1 2 3 4 5 6 7 8 9 10

Slow Fast

Steps:

Hold down the Mode switch  [6]  [5]  Setting

Setting

2 to 99

This setting may be automatically fixed so as not to exceed the

setting value of Dynamic Gate High Limit.

Steps:

Hold down the Mode switch  [6]  [6]  Setting

Setting

2 to 99

This setting may be automatically fixed so as not to be below the

setting value of Dynamic Gate Low Limit.

Setting

NOTE

Setting

NOTE

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

6-7. Fast Blast Timer

You can set the practice timer for Fast Blast (page 39). The

timer begins counting at the start of an exercise, and when

the set time is reached, it automatically ends the exercise.

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [6] to select the Training Set-

tings.

3. Press the number button [7] to select Fast Blast Timer.

4. Select your preferred practice time using the number

button [1] to [10].

7-1. Voice Guidance Volume

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [7] to select the Other Set-

tings.

3. Press the number button [1] to select Voice Guidance

Vo l u m e .

4. Set your preferred volume using the number button [1]

to [10].

7-2. Operation Sound Volume

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [7] to select the Other Set-

tings.

3. Press the number button [2] to select Operation Sound

Vo l u m e .

4. Set your preferred volume using the number button [1]

to [10].

Steps:

Hold down the Mode switch  [6]  [7]  Setting

Number button Settings

[1] Off

[2] 10 seconds

[3] 30 seconds

[4] 60 seconds

[5] 90 seconds

[6] 120 seconds

[7] 180 seconds

[8] 300 seconds

[9] 480 seconds

[10] 600 seconds

Setting

m Other Settings

Steps:

Hold down the Mode switch  [7]  [1]  Setting

Setting

1 to 10

Setting this parameter to [1] turns off the Voice Guidance.

Steps:

Hold down the Mode switch  [7]  [2]  Setting

Setting

1 to 10

Setting this parameter to [1] turns off the Operation Sound.

Setting

NOTE

Setting

NOTE

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

7-3. USB Audio Output Settings

You can set whether the USB audio input is sent to the USB

out or not. When set to “Output,” the audio data input from

a PC (for example) is mixed with your pad performance and

they are sent together to the USB out. When set to “Not out-

put,” only your pad performance is sent to the USB out,

even if the audio data is input and played from the PC.

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [7] to select the Other Set-

tings.

3. Press the number button [3] to select USB Audio Out-

put Settings.

4. Select the parameter using the number button [1] or

[2].

7-4. USB Audio Output Gain

When USB Audio Output Setting is set to “Output,” you can

set the output gain level.

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [7] to select the Other Set-

tings.

3. Press the number button [4] to select USB Audio Out-

put Gain.

4. Select the gain level using the number button [1] to

[5].

7-5. Auto Power-Off Time

You can set the time until the Auto Power-Off function

(page 22) activates or you can disable this function.

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [7] to select the Other Set-

tings.

3. Press the number button [5] to select Auto Power-Off

Time.

4. Set a time or disable this function using the number

button [1] to [7].

Steps:

Hold down the Mode switch  [7]  [3]  Setting

Number button Setting

[1] Not output

[2] Output

Steps:

Hold down the Mode switch  [7]  [4]  Setting

Number button Setting

[1] -12 dB

[2] -6 dB

[3] 0 dB

[4] +6 dB

[5] +12 dB

Setting

Steps:

Hold down the Mode switch  [7]  [5]  Setting

Number button Setting

[1] Auto Power-Off disabled

[2] 5 minutes

[3] 10 minutes

[4] 15 minutes

[5] 30 minutes (default)

[6] 60 minutes

[7] 120 minutes

Setting

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

7-6. Stereo/Mono

You can set the [PHONES/OUTPUT] jack to output either

mono or stereo sound. We recommend that you select the

Mono setting if connecting a standard mono-audio cable to

this jack in order to use your drum module with external

speakers, a mixer, or other similar equipment.

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [7] to select the Other Set-

tings.

3. Press the number button [6] to select Stereo/Mono.

4. Select Stereo/Mono using the number button [1] or

[2].

7-7. Initialize Kit

You can restore a drum kit’s default settings used for a spe-

cific music category.

1. Press the Mode switch to turn the “PLAY” light on.

2. Select a music category you wish to initialize the corre-

sponding kit using the number button [1] to [10].

3. Hold down the Mode switch to activate Menu Mode.

4. Press the number button [7] to select the Other Set-

tings.

5. Press the number button [7] to select Initialize Kit.

• The number button [1] will light up.

6. Press the number button [1].

• The number button will start to flash.

• If you do not wish to proceed with initialization, press

the Mode switch now to exit Menu Mode.

7. Press the number button [1].

• The kit will be initialized.

7-8. Delete Song

You can delete an imported MIDI song on the drum module.

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [7] to select the Other Set-

tings.

3. Press the number button [8] to select Delete Song.

• The number button [1] will light up.

4. Press the number button [1].

• The number button will start to flash.

• If you do not wish to proceed with deletion, press the

Mode switch now to exit Menu Mode.

5. Press the number button [1].

• The song will be deleted.

Steps:

Hold down the Mode switch  [7]  [6]  Setting

Number button Setting

[1] Stereo

[2] Mono

When you initialize a kit, all of the changes you have made to it

will be lost. Before proceeding, therefore, you should ensure that

the kit contains no irreplaceable settings.

Steps:

Hold down the Mode switch  [7]  [7]  [1]  [1]

Setting

NOTICE

Steps:

Hold down the Mode switch  [7]  [8]  [1]  [1]

You cannot restore a deleted song. Before proceeding, therefore,

you should ensure that the song contains no irreplaceable data.

NOTICE

Setting Parameters using Menu Mode

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

7-9. Revert to Last Power On

You can return all settings of drum kits, songs, and Menu

Mode to the settings they had when you last turned on the

drum module.

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [7] to select the Other Set-

tings.

3. Press the number button [9] to select Revert to Last

Power On.

• The number button [1] will light up.

4. Press the number button [1].

• The number button will start to flash.

• If you do not wish to proceed with initialization, press

the Mode switch now to exit Menu Mode.

5. Press the number button [1].

• The settings will be initialized.

7-10. Factory Reset

You can return all settings of drum kits, songs, and Menu

Mode to their default settings.

1. Hold down the Mode switch to activate Menu Mode.

2. Press the number button [7] to select the Other Set-

tings.

3. Press the number button [10] to select Factory Reset.

• The number button [1] will light up.

4. Press the number button [1].

• The number button will start to flash.

• If you do not wish to proceed with initialization, press

the Mode switch now to exit Menu Mode.

5. Press the number button [1].

• The settings will be initialized.

You can also restore the Factory Reset by turning on the

drum module with the VOLUME[+] and [–] buttons held

down (page 22).

Steps:

Hold down the Mode switch  [7]  [9]  [1]  [1]

• When you reset settings as described below, any changes you

have made to them since last turning on the drum module will be

lost. Before proceeding, therefore, you should ensure that they

contain no irreplaceable settings.

• After importing or deleting a song and then changing any set-

tings, using the “Revert to Last Power On” procedure does not

restore the settings they had when you last turn on the drum

module. It only restores the state before the import or delete

operation.

NOTICE

Steps:

Hold down the Mode switch  [7]  [10]  [1]  [1]

When you reset settings as described below, any changes you

have made to them will be lost. Before proceeding, therefore, you

should ensure that they contain no irreplaceable settings.

NOTICE

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

Integrating Separately Sold Accessories

As described below, you can add various accessories* to your electronic drum kit for an even more

enjoyable drumming experience. (*: Sold separately)

Please note that these optional external pads were up-to-date as of printing of this manual. Details

regarding any subsequently released models will be made available via the following web site.

https://www.yamaha.com/dtx/

By upgrading the KU100 Kick Unit and/or the hi-hat con-

troller included as part of the DTX402K, you can make your

electronic drum kit feel much closer to the real thing.

When you upgrade your KU100 to a KP65, you will need a

foot pedal to play the new kick pad.

When using a KP65, you can add pads such as a PCY95AT

Cymbal Pad. (For details, refer to “Adding a PCY95AT

Cymbal Pad” under “For DTX432K & DTX452K Own-

ers.”)

 Replacing the KU100 Kick Unit with a KP65

Kick Pad

1. Assemble the KP65 Kick Pad. For details, see Step 11

on page 18.

2. Turn off the drum module.

The KP65 Kick Pad must be connected with the drum

module turned off.

3. Disconnect the cable from the KU100 and plug it into

the [OUT > DTX] jack on the back on the KP65.

4. Turn on the drum module.

5. Set the kick type to “KP65”. For more details, see the

description of the Pedal Types parameter from Menu

Mode (page 50).

6. Play the KP65 Kick Pad.

 Replacing the bundled hi-hat controller

with an HH65 Hi-hat Controller

1. Turn off the drum module.

The HH65 Hi-hat Controller must be connected with

the drum module turned off.

2. Disconnect the cable from the bundled hi-hat controller

and plug it into the [OUTPUT] jack on the HH65.

3. Turn on the drum module.

4. Set the hi-hat controller type to “HH65”. For more

details, see the description of the Pedal Types parameter

from Menu Mode (page 50).

5. Play the HH65 Hi-hat Controller.

 Adding a PCY95AT Cymbal Pad

1. Turn off the drum module.

The PCY95AT Cymbal Pad must be connected with the

drum module turned off.

2. Using the cable that came with the cymbal pad, connect

it to the [PAD > IN] jack on the KP65 Kick Pad.

3. Turn on the drum module.

4. Play the newly added cymbal pad.

For DTX402K Owners

For DTX432K & DTX452K Owners

Advanced Techniques

DTX402K DTX432K DTX452K Owner’s Manual

Connecting to a Computer

Connecting the drum module to a computer or a smart device such as iPhone/iPad using a USB cable

lets you send and receive audio or MIDI data. This section explains how to connect the drum module

and the computer.

 Precautions when using the [USB TO HOST]

terminal

When connecting the computer to the [USB TO HOST]

terminal, make sure to observe the following points. Failing

to do so risks freezing the computer and corrupting or losing

the data.

If the computer or the drum module freezes, restart the

application software or the computer OS, or turn the power

to the drum module off and then on again.

To use audio data with a Windows computer, you need to

install the Yamaha Steinberg USB Driver.

1. Download the latest Yamaha Steinberg USB Driver

from the following URL.

https://download.yamaha.com/

After accessing the Support website (and clicking on

“Firmware/Software”), enter the appropriate model

name.

Press the [ (driver name)] button, download and

open the file.

2. Install the Yamaha Steinberg USB Driver on your com-

puter.

For more information, please refer to the Yamaha Stein-

berg USB Driver Installation Guide.

Information related to MIDI and creating music with a com-

puter, is provided in the MIDI Reference Manual. The MIDI

Reference Manual (PDF) is available for download at the

following web page.

https://download.yamaha.com/

After accessing the Support website (and clicking on

“Manual Library”), enter the appropriate model

name.

USB cable is not included.

NOTE

[USB TO HOST] terminal

(bottom panel)

Computer

USB cable

Drum module

USB terminal

• Use an A-B type USB cable. Also, make sure the cable is less

than 3 meters long. USB 3.0 cables cannot be used.

• Before connecting a computer to the [USB TO HOST] terminal,

disable any power-saving mode of the computer (such as sus-

pend, sleep, or standby).

• Before turning the power to the drum module on/off or plugging/

unplugging the USB cable to/from the [USB TO HOST] terminal,

quit any open application software on the computer.

• Please wait at least six seconds between turning the drum mod-

ule on/off and connecting or disconnecting the USB cable.

Installing the Yamaha Steinberg USB

Driver

When you use a macOS computer or when you use a Windows

computer only to handle MIDI data, installation of the Yamaha

Steinberg USB Driver is not required.

NOTICE

NOTE

• Information on system requirements is provided on the

above web page.

• For improvement, the Yamaha Steinberg USB Driver may

be upgraded without notice. For details and the most up-to-

date information, please visit the above website.

MIDI-related Reference

NOTE

Reference

DTX402K DTX432K DTX452K Owner’s Manual

Troubleshooting

Some problems may be solved by restoring the default settings (Factory Reset). If the following

instructions do not work, we recommend the Factory Reset (See page 22).

No sound is produced when a pad is struck, or the volume is lower than expected.

 Check connections as follows.

• Ensure that the pads are properly connected to the drum module’s trigger input jacks.

• Ensure that headphones or speaker are properly connected to the [PHONES/OUTPUT] jack (not the [AUX IN]

jack) on the drum module.

• Ensure that the amplifier and/or speakers connected to the drum module are turned on and are not set to the low-

est possible volume.

• If you are using a KP65 Kick Pad, try adjusting its Level dial.

• Ensure that the cables you are using are in good condition.

•

Ensure that an HH40 Hi-hat Controller is properly connected to the [HI-HAT CTL] jack and a KU100 Kick Unit is

connected to the [KICK/PAD] jack on the drum module (page 57).

 Check the drum module’s settings as follows.

• Ensure that the drum module’s volume is not turned fully down. Also when directly inputting the volume with

numerical values by using the number buttons, try pressing the number buttons in rapid succession. (See page

41)

• Adjust the following parameters from Menu Mode.

- Pad Volume (See page 43)

- Gain (See page 50)

- Pad Velocity Curve (See page 48)

- Crosstalk (See page 49)

- Snare Pad Type (See page 49)

- Pedal Type (See page 50)

- Local Control (See page 45)

 If kick sounds are not produces as expected, try the following.

• Low notes may not be produced depending on the particular headphones you are using. If necessary, try different

headphones.

•

If you are using a KU100 Kick Unit, connect an HH40 hi-hat controller before turning on the drum module. Please

do not turn the drum module on with the HH40 depressed. The drum module cannot identify the type of pedal

properly and it causes that the kick may produce much smaller sound than expected.

 If you cannot play foot closed hi-hat sounds, try the following.

• Ensure that you are operating the hi-hat controller in a firm and full manner.

• Ensure that the Double Bass Drum parameter from Menu Mode is set to “Off”. (See page 44)

• If you are using an HH65 Hi-hat Controller, set the Foot Close Position parameter from Menu Mode to a small

value. (See page 46)

For DTX402K

Reference

Troubleshooting

Reference

DTX402K DTX432K DTX452K Owner’s Manual

Sounds or volumes are not as expected.

 If hi-hat splash sounds are not produced as expected, try the following.

• Adjust the Splash Sensitivity parameter from Menu Mode. (See page 46)

 If it is difficult to produce closed hi-hat sounds with an HH65 Hi-hat Controller, try the following.

• Adjust the Foot Close Position parameter from Menu Mode. (See page 46)

 If it is difficult to produce louder and quieter foot-closed hi-hat sounds, try the following.

• Ensure that the Pedal Type parameter from Menu Mode is set correctly. (See page 50)

•

If you are using an HH40 Hi-hat Controller, the velocity is fixed regardless of how strongly or softly the HH40 is

depressed. Adjust the Foot Close Velocity parameter from Menu Mode. (See page 47)

 If pads are producing only sounds at very high volumes (i.e., high velocities), try the following.

• Adjust the sensitivity of the drum kit. (See page 26)

• Adjust the Gain parameter from Menu Mode. High settings will result in loud drum sounds. (See page 50)

• Adjust the Pad Velocity Curve parameter from Menu Mode. (See page 48)

• Ensure that you are using only the recommended Yamaha pads. (Products from other manufacturers can output

excessively large signals.)

 If the volumes of drum sounds produced by the various pads are poorly balanced, proceed as follows.

• Adjust the Pad Volume parameter from Menu Mode for each pad. (See page 43)

• Ensure that the Stereo/Mono parameter from Menu Mode is set correctly. (See page 55)

 If the drum module’s volume is not well balanced with that of the device connected to the [AUX IN] jack

(such as a portable music player), proceed as follows.

• Ensure that the volume of the connected device is set to a suitable level. (See page 21)

 If the volume of your drumming is not well balanced with that of a drum-module song, proceed as follows.

• Adjust the song volume. (See page 27)

If you notice double triggering, crosstalk, or skipped sounds (as described below), proceed as fol-

lows.

 Double triggering—i.e., multiple sounds are produced in response to a single strike:

• If the pad or drum trigger in question features a controller for adjusting output or sensitivity, turn it down.

• Ensure that the Pad Type parameter from Menu Mode is set correctly. (See page 49)

• Ensure that the Gain parameter from Menu Mode is not set too high. (See page 50)

 Crosstalk—i.e., a sound is produced by a pad other than the one that was struck:

• Adjust the following parameters from Menu Mode.

- Gain (See page 50)

- Minimum Level (See page 50)

- Crosstalk (See page 49)

 Skipped sounds—i.e., a pad does not produce a sound (usually during rolls or fills):

• Adjust the Crosstalk parameter from Menu Mode to a suitable level for each affected pad. (See page 49)

For DTX402K

Reference

Troubleshooting

DTX402K DTX432K DTX452K Owner’s Manual

* You can also find troubleshooting tips in the MIDI Reference Manual (PDF). (See page 58)

Yamaha DTX432K Electronic Drum Set El manual del propietario

Marca: Yamaha

Modelo: DTX432K Electronic Drum Set

Categoría: Tambores musicales

Tipo: El manual del propietario

Este manual también es adecuado para

Descargar PDF

informe

En otros idiomas

français: Yamaha DTX432K Electronic Drum Set Le manuel du propriétaire
italiano: Yamaha DTX432K Electronic Drum Set Manuale del proprietario
English: Yamaha DTX432K Electronic Drum Set Owner's manual
Deutsch: Yamaha DTX432K Electronic Drum Set Bedienungsanleitung
русский: Yamaha DTX432K Electronic Drum Set Инструкция по применению
Nederlands: Yamaha DTX432K Electronic Drum Set de handleiding
português: Yamaha DTX432K Electronic Drum Set Manual do proprietário
dansk: Yamaha DTX432K Electronic Drum Set Brugervejledning
polski: Yamaha DTX432K Electronic Drum Set Instrukcja obsługi
čeština: Yamaha DTX432K Electronic Drum Set Návod k obsluze
svenska: Yamaha DTX432K Electronic Drum Set Bruksanvisning
日本語: Yamaha DTX432K Electronic Drum Set 取扱説明書
Türkçe: Yamaha DTX432K Electronic Drum Set El kitabı
suomi: Yamaha DTX432K Electronic Drum Set Omistajan opas
română: Yamaha DTX432K Electronic Drum Set Manualul proprietarului

Yamaha DTX432K Electronic Drum Set El manual del propietario

Este manual también es adecuado para

Yamaha DTX432K Electronic Drum Set El manual del propietario

En otros idiomas

Documentos relacionados

Otros documentos