MooreCo Visionary Board Assembly Instructions
- Tipo
- Assembly Instructions
Visionary Boards
UPDATED AS OF: 09/14/2021 1 of 7
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
Parts List
UPDATED AS OF: 09/14/2021 2 of 7
Hardware
P1 - Glass Board
P2 - Tray Mount
P3 - Tray
x1
x1
x1
A - Outer Cap
B - Wall Mount
C - M5 x 34mm
D - Drywall Anchor
E - Masonry Anchor
F - M6 x 10mm
x6/8/10
x6/8/10
x8/10/12
x6/8/10
x6/8/10
x2
For full product warranty details, please visit:
Para obtener información sobre la garantía del producto, consulte este sitio (ingles):
Pour plus d’informations sur la garantie du produit, consultez ce site (anglais):
For questions on assembly or missing/damaged parts, please contact us using the
following information.
Para preguntas sobre el ensamblaje o piezas faltantes o dañadas, por favor
contáctenos usando la siguiente información.
Pour toute question sur le montage l-assamblage manquantes ou endommagées,
veuillez nous contacter en utilisant les l’information ci-dessous.
To register your product for warranty, please visit:
Para registrar la garantía del producto, vea este sitio (en ingles):
Pour enregistrer la garantie de votre produit, consultez ce site (en anglais):
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
WARRANTY
CARE & MAINTENANCE
PRODUCT REGISTRATION
UPDATED AS OF: 09/14/2021 3 of 7
Phone:
1.800.749.2258
(Monday – Friday, 8AM – 5PM
Central Time)
http://moorecoinc.com/warranty
https://moorecoinc.com/register
Email:
support@moorecoinc.com
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instrucciones y asegurarse que cuenta con
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
complètes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient serrées.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a l’aide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS
STEP 1
UPDATED AS OF: 09/14/2021 4 of 7
Measure your board dimensions and draw an outline of where the board will be located
on your wall. Predrill holes for wall mount clips at the locations shown below. Drill 1/8”
holes where studs are located and 1/4” holes when drilling into drywall. If installing
board in masonry drill only 1/4” holes. For 6 ft or 8 ft boards see next step for additional
predrill placement.
STEP 2
For 6 ft and 8 ft long boards add holes for additional wall mount clips along long edges
of boards. 6 ft boards will get two additional clips and 8 ft boards will get four additional
clips equally spaced as shown. Spacing from top, bottom, and left and right edges of
boards will be the same as previous step.
Top Edge of Board
Bottom Edge of Board
6” 3/4” 6”
3/4”
1 1/4” 1 1/4”
6” 6”
3/4” 3/4”
4’ x 6’
4’ x 8’
4’ x 6’
4’ x 8’
STEP 3
UPDATED AS OF: 09/14/2021 5 of 7
With caps removed, attach the wall mounts with necessary hardware as required for
installation. Do not screw any of the mounts so tightly that they are unable to slide.
After installation slide all mounts outward so that each screw is at inside edge of slot.
Screws should be tight enough to hold all mounts in place.
STEP 4
Masonry Wall
1/4” Predrill
Masonry Wall
1/4” Predrill
Masonry Wall
1/4” Predrill
E
Drywall
1/4” Predrill
Stud Wall
1/8” Predrill
C
B
D
Drywall
Stud Wall
Top
Bottom
Left Right
Adhesive Pad
Centerline
Place adhesive pads along backside of board. Use two pads per board equally spaced
along the center. For 6’ and 8’ long boards installed vertically, space pads along the
long axis. If installing tray continue to next page otherwise skip to Step 5.
Tray - STEP 1
UPDATED AS OF: 09/14/2021 6 of 7
Drill two holes 3” apart, 1” above the bottom edge of where your board will be.
Secure the Tray Mount (P2) with two screws (D) and inserts, as required.
3”
1”
Tray - STEP 2
Bottom Edge of Board
P3
F
C
P2
STEP 5
Remove adhesive backer from pads. Place board into lower mounts and secure the
outer caps, then tilt back into the top mounts and push them down. Screw in top outer
caps to hold panel in place. Finally push in left and right side mounts and screw in
outer caps to secure panel. Apply pressure to front face of board to engage adhesive
pads with wall and lock board in place.
UPDATED AS OF: 09/14/2021 7 of 7
THIS COMPLETES ASSEMBLY INSTRUCTION
-
1
-
2
-
3
-
4
-
5
-
6
-
7
MooreCo Visionary Board Assembly Instructions
- Tipo
- Assembly Instructions
en otros idiomas
- français: MooreCo Visionary Board
- English: MooreCo Visionary Board
Artículos relacionados
Otros documentos
-
Balt 74951 Guía de instalación
-
-
-
-
-
-
-