GE GFDN160GJWW Guía de instalación

Categoría
Secadoras de ropa eléctricas
Tipo
Guía de instalación
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT Save these instructions for local
electrical inspector’s use.
IMPORTANT Observe all governing codes and
ordinances.
Install the clothes dryer according to the manufacturer’s
instructions and local codes.
Note to Installer – Be sure to leave these instructions
with the Consumer.
Note to Consumer – Keep these instructions for future
reference.
Clothes dryer installation must be performed by a
qualified installer.
This dryer must be exhausted to the outdoors.
Before the old dryer is removed from service or
discarded, remove the dryer door.
Service information and the wiring diagram are located
in the control console.
Do not allow children on or in the appliance. Close
supervision of children is necessary when the appliance
is used near children.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the Warranty
.
Install the dryer where the temperature is above 50°F
for satisfactory operation of the dryer control system.
 5HPRYHDQGGLVFDUGH[LVWLQJSODVWLFRUPHWDOIRLOGXFW
and replace with UL-listed duct.
Questions? Call 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com
- Fire Hazard
WARNING
Clothes dryer installation must be performed by a
qualified installer.
Install the clothes dryer according to these
instructions and local codes.
DO NOT install a clothes dryer with flexible plastic
venting materials. If flexible metal (semi-rigid or
foil-type) duct is installed, it must be UL-listed and
installed in accordance with the instructions found
in “Connecting the Dryer to House Vent” later in
this manual. Flexible vent materials are known to
collapse, be easily crushed and trap lint. These
conditions will obstruct dryer airflow and increase
the risk of fire.
DO NOT install or store this appliance in any
location where it could be exposed to water or
weather.
To reduce the risk of severe injury or death, follow
all installation instructions.
Save these instructions. (Installers: Be sure to leave
these instructions with the customer.)
Installation Dryers
Instructions
04
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill you or hurt you and others.
$OOVDIHW\PHVVDJHVZLOOIROORZWKHVDIHW\DOHUWV\PERODQGWKHZRUG´'$1*(5µ´:$51,1*µRU´&$87,21µ7KHVH
words are defined as:
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
DANGER
WARNING
CAUTION
31-16769 04-15 GE
234D2274P004
Printed in Mexico
4.4”
(11.2 cm)
5.4”
(13.7 cm)
Installation Instructions
Tilt the dryer sideways and remove the foam
shipping pads by pulling at the sides and breaking
them away from the dryer legs. Be sure to remove all
of the foam pieces around the legs.
5HPRYHWKHEDJFRQWDLQLQJWKHOLWHUDWXUH
UNPACKING YOUR DRYER
POWER CORDS:
GE strongly recommends the use of factory specified parts.
Select the power cord to fit your installation requirements.
Order on-line at GEApplianceParts.com, 24 hours a day or
by phone at 800.626.2002 during normal business hours.
Part Number Type Length Amperage
WX9X2 3-Prong 4 Feet 30
WX9X3 3-Prong 5 Feet 30
WX9X4 3-Prong 6 Feet 30
WX9X18 4-Prong 4 Feet 30
WX9X19 4-Prong 5 Feet 30
WX9X20 4-Prong 6 Feet 30
2
ROUGH-IN
DIMENSIONS
Side View
Front View
NOTE:
Dryer height can be adjusted to match washer height
With Pedestal: 52.1” (132.33 cm)
Stacked: 84” (213.36 cm)
33” (83.8 cm)
39.3”
(99.8cm)
27”
(68.6 cm)
39.3”
(99.8 cm)
GE strongly recommends the use of factory specified parts.
These hoses are manufactured and tested to meet GE
specifications.
GE strongly recommends the use of new water supply hoses.
Hoses degrade over time and need to be replaced every 5
years to reduce the risk of hose failures and water damage.
Parts and Accessories
Order on-line at GEApplianceParts.com, 24 hours a day or
by phone at 800.626.2002 during normal business hours.
Part Number Accessory
WE25X20060 Complete Kit (hoses, Y-adapter
washers) (included)
OR
WE1M847 Long Hose and
WE01X22395 Short Hose
PM14X10056 Dryer door opening vent brush
(not included)
WX14X10007 LintEater™ Dryer rotary tube brush
(not included)
STEAM WATER HOSES (for steam dryer models only):
Installation Instructions
REQUIREMENTS FOR ALCOVE OR
CLOSET INSTALLATION
MOBILE OR MANUFACTURED HOME
INSTALLATION
3
- Explosion Hazard
WARNING
Keep flammable materials and vapors, such as gasoline,
away from dryer.
Place dryer at least 18” (46 cm) above the floor for a
garage installation.
Failure to do so can result in death, explosion, or fire.
Installation must conform to the
0$18)$&785('+20(&216758&7,21$1'
6$)(7<67$1'$5'7,7/(3$57²RU
Standard CAN/CSA-Z240 MH, or, when such
VWDQGDUGLVQRWDSSOLFDEOHZLWK$0(5,&$1
1$7,21$/67$1'$5')2502%,/(+20(
ANSI/NFPA NO. 501B.
The dryer MUST be vented to the outdoors. The
exhaust vent must be securely fastened to a
non-combustible portion of the mobile home.
The vent MUST NOT be terminated beneath a
mobile or manufactured home.
The vent duct material MUST BE METAL.
KIT 14-D346-33 MUST be used to attach the dryer
securely to the structure.
The vent MUST NOT be connected to any other
duct, vent or chimney.
Do not use sheet metal screws or other
fastening devices which extend into the interior
of the exhaust vent.
Provide an opening with a free area of at least
25 square inches for introduction of outside air
into the dryer room.
See the sections for electrical connection
information.
If the dryer is approved for installation in an
alcove or closet, it will be stated on a label on the
dryer back.
The dryer MUST be vented to the outdoors. See
WKH(;+$867,1*7+('5<(5VHFWLRQ
Minimum clearance between dryer cabinet and
adjacent walls or other surfaces is:
0” either side
3” front
3” rear
Minimum vertical space from dryer to overhead
shelves, cabinets, ceilings, etc., is 1” on top.
Consideration must be given to provide adequate
clearance for installation and service.
Closet doors must be louvered or otherwise
ventilated and have at least 60 square inches
(387 square cm) of open area. If the closet
contains both a washer and a dryer, doors must
contain a minimum of 120 square inches (774
square cm) of open area.
NOTE: WHEN THE EXHAUST DUCT IS LOCATED IN
7+(5($52)7+('5<(57+(&21),*85$7,212)
7+('8&7,1*0$<5(48,5(*5($7(57+$1µ2)
5($5&/($5$1&(.
Gas Dryers Only:
No other fuel burning appliance shall be installed
in the same closet as a gas dryer.
The dryer must be disconnected from the gas
supply piping during pressure testing at pressures
greater than ½ psi (3.5 kPa).
A 1/8 inch NPT minimum plugged tapping,
accessible for test gauge connection, must be
installed immediately upstream of the gas supply
connection to the dryer.
MINIMUM CLEARANCE OTHER THAN
ALCOVE OR CLOSET INSTALLATION
Minimum clearance to combustible surfaces and
for air opening are: 0” both sides, 1” front and
3” rear. Consideration must be given to provide
adequate clearance for installation and service.
4
Installation Instructions
CONNECTING INLET HOSES (for steam dryer models only)
CONNECTING INLET HOSES (cont.)
7. Using pliers, tighten all the couplings with an
DGGLWLRQDOWZR²WKLUGVWXUQ
NOTE: Do not overtighten. Damage to the couplings
may result.
8. Turn the water faucet on.
9. Check for leaks around the ‘’Y’’ connector, faucet
and hose couplings.
WATER SUPPLY REQUIREMENTS
Hot and cold water faucets MUST be installed
within 42 in. (107 cm) of your washer’s water
inlet. The faucets MUST be 3/4 in. (1.9 cm) garden
hose-type so inlet hoses can be connected. Water
pressure MUST be between 10 and 120 pounds
per square inch. Your water department can
advise you of your water pressure.
NOTE: A water softener is recommended to reduce
buildup of scale inside the steam generator if the
home water supply is very hard.
To produce steam, the dryer must connect to
the cold water supply. Since the washer must
also connect to the cold water, a “Y” connector
is inserted to allow both inlet hoses to make that
connection at the same time.
NOTE: Use the new inlet hoses provided; never use
old hoses.
17XUQ WKH FROG ZDWHU IDXFHW RII 5HPRYH WKH
washer inlet hose from the washer fill valve
connector (cold).
2. Ensure the rubber flat washer is in place and
attach one female coupling of the short hose
onto the washer fill valve connector. Tighten by
hand until firmly seated.
3. Attach one male end of the “Y” connector to the
other female coupling of the short hose. Ensure
the rubber flat washer is in place. Tighten by
hand until firmly seated.
4. Insert the filter screen in the coupling of the
washer’s inlet hose. If a rubber flat washer is
already in place remove it before installing the
filter screen. Attach this coupling to one male end
of the ‘’Y’’ connector. Tighten by hand until firmly
seated.
5. Ensure the rubber flat washer is in place and
attach the dryer’s long inlet hose to one male
end of the ‘’Y’’ connector. Tighten by hand until
firmly seated.
6. Ensure the rubber flat washer is in place and
attach the other end of the dryer’s long inlet
hose to the fill valve connector at the bottom of
the dryer back panel. Tighten by hand until firmly
seated.
CONNECTING INLET HOSES
10” Adjustable
wrenches (2)
8” Pipe wrench
Slip-joint pliers
Flat-blade
screwdriver
Level
Installation Instructions
TOOLS YOU WILL NEED
CONNECTING A GAS DRYER (skip for electric dryers)
Before beginning the installation, turn off
the circuit breaker(s) or remove the dryer’s circuit
fuse(s) at the electrical box. Be sure the dryer cord
is unplugged from the wall.
Turn the dryer’s gas shut-off valve in the supply
line to the OFF position.
Disconnect and discard old flexible gas connector
and ducting material.
Shut-off
Valve
MATERIALS YOU WILL NEED
4” dia. metal elbow
Pipe compound or
PTFE tape
Flexible gas line
connector
Duct clamps (2) or
Spring clamps (2)
Safety glasses
4” dia. metal duct
(recommended)
4” dia., UL-listed
flexible metal duct (if
needed)
Gloves
Soap solution for
leak detection
Exhaust hood
Duct tape
Gas pipe adapters (2),
elbow and pipe plug
5
CONNECTING A GAS DRYER (cont.)
Installation Instructions
GAS REQUIREMENTS
DRYER GAS SUPPLY CONNECTION
GAS SUPPLY
A 1/8” National Pipe Taper thread plugged
tapping, accessible for test gauge connection,
must be installed immediately upstream of the
gas supply connection to the dryer. Contact
your local gas utility should you have questions
on the installation of the plugged tapping.
Supply line is to be 1/2” rigid pipe and equipped
with an accessible shutoff within 6 feet of, and
in the same room with, the dryer.
Use pipe thread compound appropriate for
natural or LP gas or use PTFE tape.
Connect flexible metal connector to dryer and
gas supply.
The installation must conform with local codes,
or in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1/NFPA 54,
or the Natural Gas and Propane Installation
Code, CSA B149.1.
IN THE COMMONWEALTH OF
MASSACHUSETTS
This product must be installed by a licensed
plumber or gas fitter.
When using ball-type gas shut-off valves, they
shall be the T-handle type.
A flexible gas connector, when used, must not
exceed 3 feet.
ADJUSTING FOR ELEVATION
Gas clothes dryers input ratings are based on
sea level operation and need not be adjusted
for operation at or below 2000 ft. elevation. For
operation at elevations above 2000 ft., input
ratings should be reduced at a rate of 4 percent
for each 1000 ft. above sea level.
Installation must conform to local codes and
ordinances or, in their absence, the NATIONAL
FUEL GAS CODE, ANSI Z223.
<RXPXVWXVHZLWKWKLVGU\HUDIOH[LEOHPHWDO
connector (listed connector ANSI Z21.24/CSA 6.10).
The length of the connect shall not exceed 3 ft.
- Explosion Hazard
WARNING
Use a new CSA International approved flexible
gas supply line. Never reuse old flexible
connectors.
,QVWDOODVKXWRIIYDOYH
6HFXUHO\WLJKWHQDOOJDVFRQQHFWLRQV
,IFRQQHFWHGWR/3JDVKDYHDTXDOLILHGSHUVRQ
make sure gas pressure does not exceed 13”
water column.
([DPSOHVRIDTXDOLILHGSHUVRQLQFOXGHOLFHQVHG
heating personnel, authorized gas company
personnel, and authorized service personnel.
)DLOXUHWRGRVRFDQUHVXOWLQGHDWKH[SORVLRQ
or fire.
6
2"
2-5/8"
3/8" NPT MALE THREAD GAS SUPPLY
NOTE: Add to vertical dimension
the distance between cabinet
bottom to floor.

This gas dryer is equipped with a Valve & Burner
Assembly for use only with natural gas. Using
conversion kit WE25X0217, your local service
organization can convert this dryer for use with
SURSDQH/3JDV$//&219(56,2160867%(
0$'(%<3523(5/<75$,1('$1'48$/,),('
3(56211(/$1',1$&&25'$1&(:,7+/2&$/
&2'(6$1'25',1$1&(5(48,5(0(176
Install a 1/8” NPT plugged tapping to the dryer
gas line shut-off valve for checking gas inlet
pressure.
Install a flare union adapter to the plugged
tapping.
NOTE: Apply pipe compound or PTFE tape
to the threads of the adapter and plugged
tapping.
Installation Instructions
Attach the flexible metal gas line connector to
the adapter.
B
Tighten the flexible gas line connection, using
two adjustable wrenches.
C
D
Tighten all connections, using two adjustable
wrenches. Do not overtighten.
E
CONNECTING THE DRYER TO THE GAS
SUPPLY (cont.)
Open the gas shut-off valve.
F
Apply pipe compound
or PTFE tape to all
male threads.
Shut-Off
Valve
Plugged
Tapping
CONNECTING THE DRYER TO THE GAS
SUPPLY
Install a female 3/8” NPT elbow at the end of the
dryer gas inlet.
Install a 3/8” flare union adapter to the female
elbow.
IMPORTANT: Use a pipe wrench to securely hold
on to the end of the dryer gas inlet to prevent
twisting the inlet.
NOTE: Apply pipe compound or PTFE tape to the
threads of the adapter and dryer gas inlet.
A
Apply pipe compound to the
adapter and dryer gas inlet.
7
Tighten the flexible
gas line using two
adjustable wrenches.
Elbow
Adapter
Items not supplied
Adapter
1/8” NPT
Pipe Plug for
Checking Gas
Inlet Pressure
Shut-Off Valve
Pipe size at
least 1/2”
3/8” NPT
New Metal
Flexible Gas
Line Connector
Installation Instructions
TEST FOR LEAKS
Never use an open flame to test for gas leaks.
Check all connections for leaks with soapy solution
or equivalent.
Apply a soap solution. The leak test solution must
not contain ammonia, which could cause damage
to the brass fittings.
If leaks are found, close the valve, retighten the
joint and repeat the soap test.
Open Gas
Valve
Ensure proper
ground exists
before use.
Ground
Screw
ELECTRICAL CONNECTION
INFORMATION FOR GAS DRYERS (cont.)
The dryer must be electrically grounded in
accordance with local codes, or in the absence of
local codes, with the National Electrical Code, ANSI/
NFPA 70 or Canadian Electrical Code, CSA C22.1
This appliance must be supplied with 120V, 60Hz,
and be connected to a properly grounded branch
circuit protected by a 15 or 20 amp circuit breaker
or time delay fuse. If electrical supply provided
does not meet these requirements, it is the owner’s
responsibility to have a licensed electrician install a
properly grounded 3-prong outlet.
If local codes permit an external ground wire
(not provided) may be added by attaching to the
green ground screw on the rear of the dryer, and
to a grounded metal cold water pipe or other
established ground.
ELECTRICAL CONNECTION
INFORMATION FOR GAS DRYERS
- Electrical Shock Hazard
WARNING
Plug into a grounded 3 prong outlet.
DO NOT remove ground prong.
DO NOT use an adapter.
DO NOT use an extension cord.
Failure to do so can result in death, fire or electrical
shock.
8
CONNECTING A GAS DRYER (cont.)
Installation Instructions
CONNECTING AN ELECTRIC DRYER
(Skip for gas dryers and if your dryer already has a power cord attached)
Before making the electrical connection, turn off
the circuit breaker(s) or remove the dryer’s circuit
fuse(s) at the electrical box. Be sure the dryer cord
is unplugged from the wall.
1(9(5/($9(7+(
$&&(66&29(52))7+(7(50,1$/%/2&.
Slip-joint pliers
Flat-blade crewdriver
Phillips screwdriver
Level
TOOLS YOU WILL NEED
MATERIALS YOU WILL NEED
4” dia. metal elbow
3/4” strain relief
(UL recognized)
4”duct
clamps (2) or
4”spring clamps (2)
Safety glasses
4” dia. metal duct
(recommended)
4” dia., UL-listed
flexible metal duct (if
needed)
Gloves
Exhaust hood
Duct tape
Dryer power cord kit
(not provided with
dryer)
UL rated 120/240V,
30A with 3 or 4 prongs.
Identify the plug type
as per the house
receptacle before
purchasing line cord.
4” Cover Plate (Kit
WE1M454)
9
CONNECTING AN ELECTRIC DRYER (cont.)
Installation Instructions
ELECTRICAL CONNECTION
INFORMATION FOR ELECTRIC DRYERS
- Fire Hazard
WARNING
Use a new UL-listed 240V 30 amp dryer power supply
cord with closed ring terminals or spade terminals with
upturned ends.
Use a UL-listed strain relief.
Disconnect power before making electrical
connections.
Connect neutral wire (white or center wire) to center
terminal.
Ground wire (green or bare wire) must be connected to
green ground connector.
Connect remaining two supply wires to remaining two
terminals.
Securely tighten all electrical connections.
5HSODFHWKHWHUPLQDOEORFNFRYHU
Failure to do so can result in death, fire or electrical
shock.
For electrical connections using a
power cord:
ELECTRICAL CONNECTION
INFORMATION FOR ELECTRIC DRYERS
For direct wire connections:
- Fire Hazard
WARNING
Use 10 gauge copper wire.
Use a UL-listed strain relief.
Disconnect power before making electrical
connections.
Connect neutral wire (white or center wire) to center
terminal.
Ground wire (green or bare wire) must be connected to
green ground connector.
Connect remaining two supply wires to remaining two
terminals.
Securely tighten all electrical connections.
5HSODFHWKHWHUPLQDOEORFNFRYHU
Failure to do so can result in death, fire or electrical
shock.
GROUNDING INSTRUCTIONS
For a grounded, cord-connected dryer: This dryer
must be grounded. In the event of a malfunction
or breakdown, grounding will reduce the risk
of electric shock by providing a path of least
resistance for electric current. This dryer uses a
cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed
and grounded in accordance with all local codes
and ordinances.
WARNING
Improper connection of the
equipment-grounding conductor
can result in a risk of electrical shock. Check with a
qualified electrician, or service representative or
personnel, if you are in doubt as to whether the
appliance is properly grounded. DO NOT modify the
plug on the power supply cord. If it will not fit the
outlet, have a proper outlet installed by a qualified
electrician.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
For a permanently connected dryer: This
dryer must be connected to a grounded metal,
permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal on the appliance.
WARNING
Improper connection of the
equipment-grounding conductor
can result in a risk of electrical shock. Check with a
qualified electrician, or service representative or
personnel, if you are in doubt as to whether the
appliance is properly grounded.
SAVE THESE INSTRUCTIONS
10
Installation Instructions
CONNECTING DRYER USING 3-WIRE
CONNECTION
3-wire Connection
Not for use in Canada.
DO NOT use for Mobile Home Installations.
NOT for use on new construction.
NOT for use on recreational vehicles.
NOT for use in areas where local codes prohibit
grounding through the neutral conduction.
CONNECTING DRYER USING 4-WIRE
CONNECTION (MUST BE USED FOR
MOBILE HOME INSTALLATION)
NOTE: Since January 1, 1996, the National Electrical
Code requires that new constructions use a 4-wire
connection to an electric dryer. A 4-wire cord must
also be used where local codes do not permit
grounding through the neutral.
3-wire connection is NOT for use on new construction.
11
1. Turn off the circuit breaker(s) (30 amp) or remove
the dryer’s circuit fuse at the electrical box.
2. Be sure the dryer cord is unplugged from the wall
receptacle.
3.5HPRYHWKHSRZHUFRUGFRYHUORFDWHGDWWKHORZHU
back.
4.5HPRYHDQGGLVFDUGJURXQGVWUDS.HHSWKHJUHHQ
ground screw for Step 7.
5. Install 3/4 in. UL-recognized strain relief to power
cord entry hole. Bring power cord through strain
relief.
6. Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of the
terminal block (marked L1 and L2).
B. Connect the neutral (white) line to the center of
the terminal block (marked N).
7. Attach ground wire of power cord with the green
ground screw (hole above strain relief bracket).
Tighten all terminal block screws (3) securely.
8. Properly secure power cord to strain relief.
9.5HLQVWDOOWKHFRYHU
NEVER LEAVE THE COVER OFF OF THE TERMINAL
BLOCK.
NEVER LEAVE THE COVER OFF OF THE TERMINAL
BLOCK.
If required, by local code, install external ground (not
provided) to grounded metal, cold water pipe, or
other established ground determined by a qualified
electrician.
L1
N
L2
RELOCATE GREEN
GROUND SCREW
HERE
STRAIN
RELIEF
BRACKET
GREEN OR
YELLOW WIRE
3/4", UL
RECOGNIZED
STRAIN RELIEF
HOT
WIRE
SCREWS
(3)
HOT
WIRE
COVER
NEUTRAL
(White)
REMOVE GROUND STRAP
AND DISCARD. KEEP GREEN
GROUND SCREW
4 #10 AWG MINIMUM COPPER
CONDUCTORS OR 120/240V 30A POWER
SUPPLY CORD KIT MARKED FOR USE
WITH DRYERS & PROVIDED WITH
CLOSED LOOP OR SPADE TERMINALS
WITH UPTURNED ENDS (NOT SUPPLIED).
L1
L2
STRAIN RELIEF
BRACKET
3/4", UL
RECOGNIZED
STRAIN RELIEF
HOT
WIRE
HOT
WIRE
GROUND
STRAP
GREEN
GROUND
SCREW
NEUTRAL
(White)
SCREWS
(3)
IF REQUIRED, BY LOCAL CODE,
INSTALL EXTERNAL GROUND
(NOT PROVIDED) TO GROUNDED
METAL, COLD WATER PIPE, OR
OTHER ESTABLISHED GROUND
DETERMINED BY A QUALIFIED
ELECTRICIAN.
COVER
3 #10 AWG MINIMUM COPPER
CONDUCTORS OR 120/240V 30A POWER
SUPPLY CORD KIT MARKED FOR USE
WITH DRYERS & PROVIDED WITH CLOSED
LOOP OR SPADE TERMINALS WITH
UPTURNED ENDS (NOT SUPPLIED).
1. Turn off the circuit breaker(s) (30 amp) or remove
the dryer’s circuit fuse at the electrical box.
2. Be sure the dryer cord is unplugged from the wall
receptacle.
3.5HPRYHWKHSRZHUFRUGFRYHUORFDWHGDWWKHORZHU
back.
4. Install 3/4-in. UL-recognized strain relief to power cord
entry hole. Bring power cord through strain relief.
5. Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of the
terminal block (marked L1 and L2).
B. Connect the neutral (white) line to the center of
the terminal block (marked N).
6. Be sure ground strap is connected to neutral
(center) terminal of block and to green ground
screw on cabinet rear. Tighten all terminal block
screws (3) securely.
7. Properly secure power cord to strain relief.
8.5HLQVWDOOWKHFRYHU
Phillips-head
screwdriver
Duct tape or duct
clamp
5LJLGRU8/OLVWHG
flexible metal 4”
(10.2 cm) duct
Drill with 1/8” drill bit
(for bottom venting)
Hacksaw
Vent hood
Installation Instructions
EXHAUSTING THE DRYER
- Fire Hazard
WARNING
This dryer MUST be vented to the outdoors.
Use only 4” rigid metal ducting for the home
exhaust vent.
Use only 4” rigid metal or UL-LISTED transition duct
to connect the dryer to the home exhaust duct.
DO NOT use a plastic vent.
DO NOT exhaust into a chimney, kitchen exhaust,
gas vent, wall, ceiling, attic, crawl space, or
concealed space of a building.
DO NOT install a screen in or over the exhaust duct.
DO NOT use duct longer than specified in the
exhaust length table.
Failure to follow these instructions can result in
death or fire.
12
TOOLS AND MATERIALS YOU WILL
NEED TO INSTALL EXHAUST DUCT
CONNECTING THE DRYER TO HOUSE
VENT
RIGID METAL TRANSITION DUCT
For best drying performance, a rigid metal transition
duct is recommended.
5LJLGPHWDOWUDQVLWLRQGXFWVUHGXFHWKHULVNRIFUXVKLQJ
and kinking.
UL-LISTED FLEXIBLE METAL CLOTHES DRYER
TRANSITION DUCT
If rigid metal cannot be used, then UL-LISTED flexible
PHWDOFORWKHVGU\HUWUDQVLWLRQGXFW*(SDUWV²
PM08X10085, WX08X10085 or WX08X10077) can be
used.
Never install transition duct in walls, ceilings, floors or
other enclosed spaces.
Total length of transition duct should not exceed
8’ (2.4 m).
For many applications, installing elbows at both
the dryer and the wall is highly recommended (see
illustrations at right). Elbows allow the dryer to sit
close to the wall without kinking and/or crushing the
transition duct, maximizing drying performance.
Avoid resting the duct on sharp objects.
UL-LISTED FLEXIBLE METAL (FOIL-TYPE) TRANSITION
DUCT
In special installations, it may be necessary to connect the
dryer to the home exhaust vent using flexible metal (foil-type)
WUDQVLWLRQGXFW8/²/,67('XQLYHUVDOIOH[LEOHGU\HUWUDQVLWLRQ
GXFW*(SDUWV²30;RU:;;PD\EHXVHG21/<LQ
installations where rigid metal or flexible metal transition
ducting cannot be used AND where a 4” diameter can be
maintained throughout the entire length of the transition duct
.
In Canada and the United States, only transition ducts
that comply with “UL 2158A STANDARD FOR CLOTHES
DRYER TRANSITION DUCT” shall be used.
Avoid resting the duct on sharp objects.
For best drying performance:
1. Slide one end of the duct over the clothes dryer
outlet pipe.
2. Secure the duct with a clamp.
3. With the dryer in its permanent position, extend
the duct to its full length. Allow 2
of duct to
overlap the exhaust pipe. Cut off and remove
excess duct. Keep the duct as straight as
possible for maximum airflow.
4. Secure the duct to the exhaust pipe with the
other clamp.
Installation Instructions
Using exhaust longer than specified length will:
 Increase the drying times and the energy cost.
 5HGXFHWKHGU\HUOLIH
 $FFXPXODWHOLQWFUHDWLQJDSRWHQWLDOILUH
hazard.
The correct exhaust installation is YOUR
RESPONSIBILITY.
Problems due to incorrect installation are not
covered by the warranty.
The MAXIMUM ALLOWABLE length of the exhaust
system depends upon the type of duct, number of
turns, the type of exhaust hood (wall cap) and all
conditions noted on the chart.
 Internal elbows added for side or bottom vent
conversions must be included in the total elbow
count.
 Any elbow greater than 45° should be treated as
a 90° elbow.
 Two 45° elbows will be treated like one 90°
elbow.
 For every additional 90° elbow, reduce the
allowable vent system length by 10 feet.
 When calculating the total vent system length,
you must add all the straight portions and elbows
of the system (including the transition duct).
EXHAUST LENGTH
13
DO NOT bend
or collapse
ducting. Use
elbows if turns
are necessary.
DO NOT use
excessive
exhaust
length. Cut
duct as short
as possible.
DO NOT
crush duct
against the
wall
.
DO NOT
set dryer
on duct
.
DO cut duct as short
as possible and install
straight into wall.
DO use elbows when
turns are necessary.
Elbows
4" DIA.
4"
4" DIA.
4" DIA.
2-1/2"
RECOMMENDED MAXIMUM LENGTH
Exhaust Hood Types
Recommended
No. of 90°
Elbows
Rigid
Metal
Rigid
Metal
90 Feet
60 Feet
45 Feet
35 Feet
25 Feet
60 Feet
45 Feet
35 Feet
25 Feet
15 Feet
0
1
2
3
4
Use only for short
run installations
EXHAUST LENGTH
EXHAUSTING THE DRYER (cont.)
Installation Instructions
BEFORE YOU BEGIN
5HPRYHDQGGLVFDUGH[LVWLQJSODVWLFRUPHWDOIRLO
duct and replace with UL-listed duct.
5HPRYHDQ\OLQWIURPWKHZDOOH[KDXVWRSHQLQJ
Internal
Duct
Opening
Wall
Check that exhaust
hood damper opens
and closes freely.
STANDARD REAR EXHAUST
We recommend that you install your dryer before
installing your washer. This will permit direct
access for easier exhaust connection.
Slide the end of the exhaust duct on the back of the
dryer and secure with duct tape or a hose clamp.
NOTE: We strongly recommend using rigid metal
exhaust duct.
For straight-line installation, connect the dryer
exhaust to the wall, using duct tape.
RECOMMENDED CONFIGURATION TO
MINIMIZE EXHAUST BLOCKAGE
Using duct elbows will prevent duct kinking and
collapsing.
Duct
Transition
Ducting
Wall Side
Dryer
Side
14
EXHAUST SYSTEM CHECKLIST
HOOD OR WALL CAP
Terminate in a manner to prevent back drafts or entry
of birds or other wildlife.
Termination should present minimal resistance to
the exhaust airflow and should require little or no
maintenance to prevent clogging.
Wall caps must be installed at least 12” above ground
level or any other obstruction with the opening
pointed down.
SEPARATION OF TURNS
For best performance, separate all turns by at least
4 ft. of straight duct, including distance between last
turn and dampened wall cap.
SEALING OF JOINTS
All joints should be tight to avoid leaks. The male end
of each section of duct must point away from the
dryer.
Duct joints should be made air- and moisture-tight
by wrapping the overlapped joints with duct tape or
aluminum tape.
Do not assemble ductwork with any fasteners
that extend into the duct. These fasteners can
accumulate lint, creating a potential fire hazard.
Horizontal runs should slope down towards the
outdoors 1/4” per foot.
Provide an access for inspection and cleaning of
the exhaust system, especially at turns and joints.
Exhaust system shall be inspected and cleaned at
least once a year.
INSULATION
Ductwork that runs through an unheated area or is
near air conditioning should be insulated to reduce
condensation and lint buildup.
15
Installation Instructions
SIDE OR BOTTOM VENTING
Dryer Exhaust to right of cabinet for Electric
models only.
Dryer Exhaust to left of cabinet for Gas and
Electric models.
Dryer Exhaust to the bottom of cabinet for
Gas and Electric models.
Detach and remove the right (electric models only),
OHIWRUERWWRPNQRFNRXWDVGHVLUHG5HPRYHWKH
screw inside the dryer exhaust duct and save. Pull
the duct out of the dryer.
Fixing hole
Cut the duct as shown and keep portion A.
ADDING A NEW DUCT
5HFRQQHFWWKHFXWSRUWLRQ$RIWKHGXFWWRWKH
blower housing. Make sure that the shortened
duct is aligned with the tab in the base. Use the
screw saved previously to secure the duct in place
through the tab on the appliance base.
ADDING ELBOW AND DUCT FOR EXHAUST TO
LEFT OR RIGHT SIDE OF CABINET
Preassemble 4” elbow with 4” duct. Wrap duct
tape around joint.
,QVHUWGXFWDVVHPEO\HOERZ¿UVWWKURXJKWKH
side opening and connect the elbow to the dryer
internal duct.
Be sure not to pull or damage the electrical wires
inside the dryer when inserting the duct.
A
13
1
ø2” (34.29cm)
TAB LOCATION
- Fire Hazard
WARNING
Close the back opening with cover plate (Kit
WE1M454).
Disconnect dryer from electrical supply.
Wear gloves and arm guards.
Failure to do so may result in fire, electrical shock
or lacerations.
5HPRYH
screw
and save
5HPRYHGHVLUHG
knockout (one only)
5LJKW
(electric
models
only)
Left
Bottom
Through the rear opening, locate the tab in the
middle of the appliance base. Lift the tab to about
45°,
using a flat-blade screwdriver.
Bend tab
up 45°
Not for gas
Portion “A”
Left side
exhaust
Fixing
hole
Exhaust can
be added to
left or right
(electric
models
only) side
Duct
tape
EXHAUSTING THE DRYER (cont.)
NEVER LEAVE THE BACK OPENING WITHOUT THE
PLATE.
(Kit WE1M454.)
Installation Instructions
SIDE OR BOTTOM VENTING (cont.)
Connect standard metal elbows and ducts to
complete the exhaust system. Cover back opening
with a plate (Kit WE1M454) available from your
local service provider. Place dryer in final location.
ADDING COVER PLATE TO REAR OF CABINET
ADDING ELBOW AND DUCT FOR EXHAUST TO
LEFT OR RIGHT SIDE OF CABINET (cont.)
Plate
(Kit WE1M454)
Apply duct tape as
shown on the joint
between the dryer
internal duct and the
elbow, and also the joint
between the elbow and
the side duct.
Use 4” rigid metal ducting only inside the dryer.
Internal duct joints must be secured with tape,
otherwise they may separate and cause a safety
hazard.
16
DUCT
TAPE
ADDING ELBOW FOR EXHAUST THROUGH
BOTTOM OF CABINET
 Insert the elbow through the rear opening and
connect it to the dryer internal duct.
Apply duct tape as
shown on the joint
between the dryer
internal duct and the
elbow, and also the
joint between the
elbow and the bottom
duct.
Internal duct joints must be secured with tape;
otherwise, they may separate and cause a safety
hazard.
Duct tape
FINAL SETUP
LEVEL THE DRYER
Stand the dryer upright near the final location and
adjust the four leveling legs at the corners to ensure
that the dryer is level from side to side and front to
rear.
Lower
5DLVH
PLUG DRYER IN
1
2
DRYER START-UP
Press the Power button.
NOTE: If the dryer has been exposed to
temperatures below freezing for an extended
period of time, allow it to warm up before pressing
Power. Otherwise, the display will not come on.
The dryer is now ready for use.
3
Ensure proper
ground exists
before use.
Lea estas instrucciones por completo y con
detenimiento.
IMPORTANTE Guarde estas instrucciones
para el uso de inspectores eléctricos locales.
IMPORTANTECumpla con todos los
códigos y ordenanzas vigentes.
Instale la secadora de acuerdo con las instrucciones
del fabricante y los códigos locales.
 1RWDDOLQVWDODGRU² Asegúrese de dejar estas
instrucciones con el consumidor.
 1RWDDOXVXDULR² Conserve estas instrucciones para
referencia futura.
La instalación de la secadora debe efectuarla un
instalador calificado.
Esta secadora debe tener una salida al exterior.
Antes de que la secadora antigua sea retirada del
servicio o eliminada, quítele la puerta.
La información sobre reparaciones y el diagrama del
cableado se encuentran en la consola de control.
No permita que niños se suban o se metan dentro
del artefacto. Se requiere una supervisión estricta
cuando el aparato es utilizado cerca de niños.
El instalador tiene la responsabilidad de efectuar una
instalación adecuada.
La garantía no cubre las fallas del producto debido a
una instalación incorrecta. .
 ,QVWDOHODVHFDGRUDHQOXJDUHVGRQGHODWHPSHUDWXUD
sea mayor a 50°F para un funcionamiento
satisfactorio del sistema de control de la secadora.
 4XLWH\GHVFDUWHHOFRQGXFWRH[LVWHQWHGHSOiVWLFR
o de papel de aluminio y coloque un conducto
aprobado por UL.
Instrucciones Secadora
de instalación
04
Si tiene alguna pregunta, llame a 800.GE.CARES (800.432.2737) o visite nuestro sitio Web en: GEAppliances.com
ADVERTENCIA
- Riesgo de incendio
La instalación de la secadora debe efectuarla un
instalador calificado.
Instale la secadora de ropa de acuerdo con estas
instrucciones y en cumplimiento con los códigos
locales
NO instale una secadora de ropa con conductos
GHSOiVWLFRIOH[LEOH6LVHLQVWDODXQFRQGXFWR
flexible de metal (semi rígido o de tipo papel de
aluminio), debe estar aprobado por UL e instalarse
de acuerdo con las instrucciones de “Cómo
conectar la secadora a la ventilación doméstica”
de este manual. Los materiales de los conductos
flexibles a menudo se desploman, se aplastan y
atrapan pelusas. Estas condiciones obstruyen la
corriente de aire de la secadora e incrementan el
riesgo de incendio.
NO instale o almacene este aparato en un
lugar donde se vea expuesto al agua o a las
inclemencias del tiempo.
Para reducir el riesgo de una lesión grave o de
muerte, cumpla con todas las instrucciones de
instalación.
Guarde estas instrucciones. (Instaladores:
Asegúrense de dejar estas instrucciones al
consumidor).
ANTES DE COMENZAR
Éste es el símbolo de alerta de seguridad. El mismo alerta sobre potenciales riesgos que le pueden producir la muerte
ROHVLRQHVWDQWRDXVWHGFRPRDRWUDVSHUVRQDV7RGRVORVPHQVDMHVGHVHJXULGDGHVWDUiQDFRQWLQXDFLyQGHOVtPEROR
de alerta de seguridad y con la palabra “PELIGRO”, “ADVERTENCIA” o “PRECAUCIÓN”. Estas palabras se definen como:
Indica una situación de riesgo que, si no se evita, producirá la muerte o lesiones graves.
Indica una situación de riesgo que, si no se evita, podría producir la muerte o lesiones graves.
Indica una situación de riesgo que, si no se evita, podría resultar en lesiones menores o moderadas.
PELIGRO
ADVERTENCIA
PRECAUCIÓN
31-16769 04-15 GE
234D2274P004
4,4”
(11,2 cm)
2
Instrucciones de instalación
Incline la secadora de costado y saque los soportes de
HVSXPDGHHPEDODMHWLUDQGRGHORVFRVWDGRV\TXLWiQGRORV
de las patas de la secadora. Asegúrese de quitar todas las
piezas de espuma de las patas.
Saque la bolsa que contiene la información.
CÓMO DESEMPACAR LA SECADORA
CABLES DE CORRIENTE:
*(UHFRPLHQGDHQIiWLFDPHQWHHOXVRGHSLH]DVHVSHFtILFDVGH
IiEULFD6HOHFFLRQHHOFDEOHGHFRUULHQWHTXHVHDGHF~HDVXV
requisitos de instalación.
Ordene a través de Internet en GEAppliancesParts.com, las 24
horas del día o en forma telefónica llamando al 800.626.2002,
durante el horario comercial habitual.
Pieza Nº Tipo Longitud Amperios
WX9X2 3-Clavijas 4 Pies 30
WX9X3 3-Clavijas 5 Pies 30
WX9X4 3-Clavijas 6 Pies 30
WX9X18 4-Clavijas 4 Pies 30
WX9X19 4-Clavijas 5 Pies 30
WX9X20 4-Clavijas 6 Pies 30
Visión lateral
5.4”
(13,7 cm)
DIMENSIONES
APROXIMADAS
Visión frontal
NOTE :
La altura de la secadora puede ser ajustada para quedar a la misma a altura
de la lavadora
Con pedestal: 52.1” (132.33 cm)
Apilada: 84” (213.36 cm)
33” (83,8 cm)
39.3”
(99,8cm)
27”
(68,6 cm)
39,3”
(99,8 cm)
*(UHFRPLHQGDHQIiWLFDPHQWHHOXVRGHSLH]DVHVSHFtILFDV
GHIiEULFD$FRQWLQXDFLyQILJXUDXQDOLVWDGHPDQJXHUDV
GHIiEULFDTXHSRGUiDGTXLULU'LFKDVPDQJXHUDVVRQ
fabricadas y probadas de modo que se cubran las
especificaciones de GE.
*(UHFRPLHQGDHQIiWLFDPHQWHHOXVRGHQXHYDVPDQJXHUDV
de suministro de agua. Con el paso del tiempo, las mangueras
se degradan y deben ser reemplazadas cada 5 años, a fin de
reducir el riesgo de fallas sobre las mismas y daños con el agua.
Piezas y Accesorios
Ordene hoy a través de Internet en GEAppliancesparts.com,
las 24 horas del día o en forma telefónica llamando al
800.626.2002, durante el horario comercial habitual.
Número de Pieza Accesorio
WE25X20060 Kit Completo (mangueras, lavadora con
adaptador en Y) (incluido)
O
WE1M847 Manguera Larga y
WE01X22395 Manguera Corta
PM14X10056 Cepillo para abertura de ventilación de la
secadora (no incluido)
WX14X10007 Cepillo giratiro para tubería LintEater™
MANGUERA DE VAPOR Y AGUA (sólo para los modelos de secadoras de vapor):
3
Instrucciones de instalación
REQUERIMIENTOS PARA INSTALACIÓN
EN NICHOS O ARMARIOS
INSTALACIÓN EN CASAS MÓVILES
O PREFABRICADAS
- Riesgo de
explosión
ADVERTENCIA
Mantenga cualquier material y vapores inflamables,
tales como gasolina, alejados de la secadora.
Coloque la secadora a por lo menos 18” (46 cm.) del
piso cuando sea instalada en un garaje.
6LQRVHFXPSOHFRQHVWRVHSRGUiSURGXFLUXQD
explosión, incendio o la muerte.
Instalación debe cumplir con la NORMA
SOBRE CONSTRUCCIÓN Y SEGURIDAD DE CASAS
PREFABRICADAS, TÍTULO 24, PARTE 32-80 o
Norma CAN/CSA-Z240 MH, o, cuando dicha
norma no sea aplicable, con la NORMA NACIONAL
ESTADOUNIDENSE PARA CASAS MÓVILES, ANSI/
NFPA Nº 501B.
La secadora DEBE tener ventilación al exterior. La
YHQWLODFLyQGHOHVFDSHGHEHUiHVWDUDMXVWDGRGH
forma segura a una parte no combustible de la
casa rodante.
La ventilación NO DEBE terminar debajo de una
casa móvil o prefabricada.
El material del conducto de ventilación DEBE SER
METAL.
DEBE utilizarse el KIT 14-D346-33 para conectar
bien la secadora a la estructura.
La ventilación NO DEBE conectarse a ningún otro
conducto, ventilación o chimenea.
No utilice tornillos para placas de metal u otros
dispositivos de sujeción que se extiendan
al interior de la ventilación de salida.
Debe contar con una abertura con un espacio
libre de por lo menos 25 pulgadas cuadradas
para el ingreso de aire exterior dentro de la
secadora habitación.
Para acceder a información sobre la conexión
eléctrica, consulte la section.
Si se aprobó la instalación de su secadora en
DOFREDRDUPDULRHVWRILJXUDUiHQXQDHWLTXHWD
en el reverso de la secadora.
Esta secadora DEBE tener una ventilación
al exterior. Ver la sección SALIDA AL EXTERIOR
DE LA SECADORA.
El espacio libre mínimo entre la secadora y las
paredes adyacentes u otras superficies es:
0” en ambos lados
3” en el frente
3” en la parte trasera
 (OHVSDFLRYHUWLFDOPtQLPRGHODSDUWHVXSHULRUGH
la secadora hasta los estantes, armarios, techos,
etc, es de 1.
6HGHEHUiFRQVLGHUDUTXHVHGHEHEULQGDUHO
despeje adecuado para la instalación y el servicio
técnico.
Las puertas del armario deben contar con rejillas
u otro tipo de ventilación y tener por lo menos
60 pulgadas cuadradas de espacio abierto
igualmente distribuido. Si el armario incluye una
lavadora y una secadora, las puertas deben
contener un mínimo de 120 pulgadas cuadradas
de espacio abierto distribuido uniformemente.
NOTA: CUANDO EL CONDUCTO DE ESCAPE
SE ENCUENTRA EN LA PARTE TRASERA DE LA
SECADORA, LA CONFIGURACIÓN DEL DUCTO DE
(6&$3(38('(5(48(5,50$6'(µ'((63$&,2
EN LA PARTE TRASERA.
Secadoras a Gas Únicamente:
1RVHGHEHUiLQVWDODUQLQJ~QRWURHOHFWURGRPpVWLFR
que consuma combustible en el mismo armario
donde haya una secadora a gas.
/DVHFDGRUDVHGHEHUiGHVFRQHFWDUGHODWXEHUtDGH
suministro de gas durante la prueba de presión en
presiones superiores a ½ psi (3.5 kPa).
8QDURVFDFXELHUWD137GHµDFFHVLEOHSDUD
la conexión de un dispositivo de calibración,
GHEHUiVHULQVWDODGDLQPHGLDWDPHQWHDUULEDGHOD
conexión del suministro de gas a la secadora.
ESPACIO LIBRE MÍNIMO EN OTROS
ESPACIOS QUE NO SEAN INSTALACIONES
EN NICHOS O ARMARIOS
Los espacios libres mínimos respecto de superficies
combustibles y de aberturas de aire son: 0” a
ambos lados, 1” (25.4mm) en el frente y 3” (75mm)
en la parte trasera. Debe tenerse en cuenta un
espacio libre adecuado para un funcionamiento y
reparación correctos.
4
Instrucciones de instalación
CÓMO CONECTAR MANGUERAS DE ENTRADA
(sólo para los modelos de secadoras de vapor)
CÓMO CONECTAR MANGUERAS
DE ENTRADA
Para producir vapor, la secadora debe conectarse
al suministro de agua fría. Ya que la lavadora
también debe conectarse al agua fría, debe
introducirse un conector en “Y” para permitir
que ambas mangueras de entrada puedan
utilizarse al mismo tiempo.
NOTA: Utilice las nuevas mangueras de entrada
provistas; nunca utilice mangueras viejas.
1.&LHUUHHOJULIRGHDJXDIUtD4XLWHODPDQJXHUD
de entrada de la lavadora del conector de la
YiOYXODGHOOHQDGRIUtD
2. Asegúrese de que la arandela plana de goma se
encuentre en su lugar y sujete una unión hembra
GHODPDQJXHUDFRUWDHQHOFRQHFWRUGHODYiOYXOD
de llenado de la lavadora. Ajuste a mano hasta
que esté firmemente asentada.
3. Sujete un extremo macho del conector en “Y” a la
unión hembra de la manguera corta. Asegúrese
de que la arandela plana de goma se encuentre
en su lugar. Ajuste a mano hasta que esté
firmemente asentada.
4. Introduzca el filtro en la unión de la manguera
de entrada de la lavadora. Si la arandela plana
de goma ya se encuentra en su lugar, quítela
antes de instalar el filtro. Sujete esta unión
a un extremo macho del conector en “Y”. Ajuste
a mano hasta que esté firmemente asentada.
5. Asegúrese de que la arandela plana de goma se
encuentre en su lugar y sujete la manguera larga
de entrada de la secadora a un extremo macho
del conector en “Y”. Ajuste a mano hasta que esté
firmemente asentada.
6. Asegúrese de que la arandela plana de goma
se encuentre en su lugar y sujete el otro extremo
de la manguera larga de entrada al conector
GHODYiOYXODGHOOHQDGRHQODSDUWHLQIHULRUGHO
panel trasero de la secadora. Ajuste a mano
hasta que esté firmemente asentada.
CÓMO CONECTAR MANGUERAS
DE ENTRADA (cont.)
7. Utilizando alicates, ajuste todas las uniones con
un giro adicional de dos tercios.
NOTA:1RDMXVWHGHPiV3XHGHQGDxDUVHODV
uniones.
8. Abra el grifo de agua.
9. Controle la presencia de pérdidas alrededor
del conector en “Y”, el grifo y las uniones
de las mangueras.
REQUISITOS DE SUMINISTRO DE AGUA
Los grifos de agua caliente y fría DEBEN instalarse
dentro de las 42 pulg. (107 cm) de la entrada de
agua de la lavadora. Los grifos DEBEN ser del tipo
de manguera de jardín de 3/4 pulg. (1.9 cm) para
que las mangueras de entrada puedan conectarse.
La presión de agua DEBE hallarse entre 10 y 120
libras por pulgada cuadrada. La compañía de agua
puede informarle sobre la presión de agua.
NOTA: Se recomienda el uso de un suavizante de
agua para reducir la acumulación de sarro dentro
del generador de vapor si el suministro doméstico
contiene agua muy dura.
CÓMO CONECTAR UNA SECADORA A GAS
(si se cuenta con una secadora eléctrica, saltear este paso)
Llaves ajustables
de 10” (2)
Llave para tubos de
8”
Pinzas
Destornillador
de lados planos
Nivel
5
Instrucciones de instalación
HERRAMIENTAS NECESARIAS
Antes de comenzar la instalación, apague
el disyuntor o quite los fusibles de la secadora
de la caja eléctrica. Verifique que el cable
de la secadora esté desenchufado
del tomacorriente.
*LUHDODSRVLFLyQ2))DSDJDGRODYiOYXODGHJDV
de la secadora de la línea de suministro.
Desconecte y elimine el conector flexible de gas
y el material del conducto.
9iOYXOD
de cierre
MATERIALES NECESARIOS
Codo de metal de
4”GLiPHWUR
Compuesto o PTFE
cinta para tuberías
Conector de tubería
de gas flexible
Abrazaderas
de tubería (2) o
abrazaderas de
resorte (2)
Gafas de seguridad
Conducto de metal
GHµGLiPHWUR
(recomendado)
Conducto de
metal flexible de 4”
GLiPHWURVLIXHVH
necesario)
Guantes
Solución jabonosa
para detección de
pérdidas
Campana de salida
Cinta aislante
Gas adaptador (2),
codo, y tapón de
tubería
CÓMO CONECTAR UNA SECADORA A GAS (cont.)
6
Instrucciones de instalación
REQUERIMIENTOS DE GAS
CONEXIÓN DE SUMINISTRO DE GAS
DE LA SECADORA
SUMINISTRO DE GAS
Debe instalarse una toma a rosca de 1/8” NPT,
accesible para una conexión del manómetro de
prueba, inmediatamente en sentido ascendente
de la conexión de suministro de gas hacia
la secadora. Si tiene dudas sobre la instalación
de la toma, comuníquese con su empresa
proveedora de gas local.
La línea de suministro debe ser de tubería rígida
de 1/2” y debe contar con un cierre accesible
dentro de los 6 pies de la secadora, dentro
de la misma habitación donde se encuentra
la misma.
Utilice compuesto para rosca de tubería
apropiado para gas natural o LP o utilice cinta
de PTFE.
Una el conector de metal flexible a la secadora
y al suministro de gas.
/DLQVWDODFLyQGHEHUiVHUFRQIRUPHFRQORVFyGLJRV
locales, o en ausencia de los códigos locales, con
el Código Nacional de Gas Combustible (National
Fuel Gas Code), ANSI Z223.1/NFPA 54, o el Código de
Instalación de Gas Natural o Propano (Natural Gas
and Propane Installation Code), CSA B149.1.
EN LA MANCOMUNIDAD DE
MASSACHUSETTS
Este producto debe instalarlo un plomero
matriculado o un instalador de gas.
&XDQGRXVHYiOYXODVHVIpULFDVGHDSDJDGR
GHJDVGHEHUiQVHUGHOWLSRGHPDQLMDHQ7
Si se usa una conexión flexible para gas, ésta
no debe superar los 3 pies.
'HEHXWLOL]DUXQFRQHFWRUIOH[LEOHPHWiOLFR
listado por ANSI Z21.24/CSA 6.10. La longitud del
FRQHFWRUQRH[FHGHUiSLHV
AJUSTE PARA ELEVACIÓN
Los niveles de entrada de las secadoras de ropa
DJDVHVWiQEDVDGRVHQHOIXQFLRQDPLHQWRDOQLYHO
de mar y no necesitan ajustes para funcionar
en o por debajo de los 2000 pies de elevación.
3DUDXQIXQFLRQDPLHQWRDPiVGHSLHVGH
elevación, los niveles de entrada se deberían
reducir a un promedio del 4 por ciento por cada
1000 pies sobre el nivel del mar.
La instalación debe cumplir con los códigos
y ordenanzas locales, o en su ausencia, con
el CÓDIGO NACIONAL DE GAS COMBUSTIBLE
(NATIONAL FUEL GAS CODE), ANSI Z223.
- Riesgo de
explosión
ADVERTENCIA
Use una línea nueva de suministro de gas flexible
que esté aprobada por CSA International. Nunca
vuelva a usar conectores flexibles viejos.
,QVWDOHODYiOYXODGHFLHUUH
'HIRUPDVHJXUDDMXVWHWRGDVODVFRQH[LRQHVGH
gas.
Si la conexión fue realizada a gas LP, solicite a
una persona calificada que le asegure que la
presión del gas no supera una columna de agua
de 13”.
Ejemplos de una persona calificada incluyen:
Personal de calefacción calificado, personal
autorizado de una compañía de gas, y personal
autorizado del servicio técnico.
6LQRVHFXPSOHFRQHVWRVHSRGUiSURGXFLUOD
muerte, una explosión o incendio.
2"
2-5/8"
SUMINISTRO DE GAS ROSCA MACHO NPT DE 3/8"
NOTA: Agregue a la dimensión vertical la distancia
entre la parte inferior del gabinete y el piso.
(VWDVHFDGRUDDJDVHVWiHTXLSDGDFRQXQ
PRQWDMHGHYiOYXOD\TXHPDGRUSDUDXWLOL]DUVyOR
con gas natural. Mediante el kit de conversión
WE25X0217, la organización de atención local
puede convertir esta secadora para su uso con
gas propano (LP). TODAS LAS CONVERSIONES
DEBEN LLEVARLAS A CABO PERSONAL
CAPACITADO Y CALIFICADO EN CUMPLIMIENTO
&21&Ï',*26/2&$/(6<5(48(5,0,(1726'(
ORDENANZAS.
Instale una toma a rosca de 1/8” NPT
HQODYiOYXODGHDSDJDGRGHODWXEHUtDGHJDV
de la secadora para controlar la presión
de gas en la entrada.
Instale un adaptador de unión cónica
en la toma a rosca.
NOTA: Aplique compuesto para tubería o cinta
PTFE a las roscas del adaptador y a la toma.
Instrucciones de instalación
Una el conector de tubería de gas de metal
flexible al adaptador.
B
Ajuste la conexión de tubería flexible de gas,
utilizando dos llaves ajustables.
C
D
Ajuste todas las conexiones mediante
dos llaves ajustables. No ajuste de más.
E
CÓMO CONECTAR LA SECADORA
AL SUMINISTRO DE GAS (cont.)
&LHUUHODYiOYXODGHDSDJDGRGHOJDV
F
Aplique compuesto para
tubería o cinta PTFE en
todas las roscas macho.
9iOYXODGHDSDJDGR
Toma a
rosca
CÓMO CONECTAR LA SECADORA
AL SUMINISTRO DE GAS
Instale un codo hembra NPT de 3/8” al final
de la entrada de gas de la secadora.
Instale un adaptador de unión cónica
de 3/8” al codo hembra.
IMPORTANTE: Utilice una llave para tubos para
sostener bien el extremo de la entrada de gas
de la secadora para no doblar la entrada.
NOTA: Aplique compuesto para tubería o cinta
PTFE a las roscas del adaptador y la entrada de
gas de la secadora.
A
7
Aplique compuesto para tubería al
adaptador y a la entrada de gas de la
secadora.
CONECTOR NUEVO
DE LÍNEA DE GAS
DE METAL FLEXIBLE
ADAPTADOR
CODO
ITEMS NOT SUPPLIED
ADAPTADOR
VÁLVULA DE CIERRE
TAMAÑO DE TUBERÍA
AL MENOS 1/2"
TAPÓN DE TUBERÍA
NPT DE 1/8” PARA
CONTROLAR LA
PRESIÓN DE ENTRADA
DE GAS
NPT DE 3/8”
EXTREMO
ABOCINADO
NPT
Tighten the flexible
gas line using two
adjustable wrenches.
Instrucciones de instalación
8
PRUEBA DE PÉRDIDAS
Abra la
YiOYXOD
de gas
CONEXIÓN ELÉCTRICA INFORMACIÓN
SOBRE LAS SECADORAS A GAS (cont.)
La secadora debe contar con una conexión
eléctrica a tierra en cumplimiento con los códigos
locales, o si éstos no existieran, de acuerdo con
el Código Eléctrico Nacional, ANSI/NFPA 70 o el
Código Eléctrico Canadiense CSA C22.1.
Este artefacto debe contar con un suministro de
120V, 60Hz, debe estar conectado a un circuito
derivado individual con una adecuada conexión
a tierra y deben contar con la protección de un
disyuntor o fusible de tiempo retardado de 15 o
20 amperios. Si el suministro eléctrico provisto no
reúne estos requerimientos, es responsabilidad
del dueño solicitar a un electricista calificado la
instalación de un tomacorriente de 3 patas con
conexión a tierra.
Tornillo de
conexión a tierra
Verifique que haya
una conexión a tierra
adecuada antes del uso.
Nunca utilice una llama abierta para detectar
pérdidas de gas.
Controle todas las conexiones con una solución
jabonosa o un elemento equivalente.
Aplique una solución jabonosa. La solución para
controlar pérdidas no debe contener amoníaco,
ya que este producto puede dañar los accesorios
de bronce.
6LVHGHWHFWDQSpUGLGDVFLHUUHODYiOYXODYXHOYD
a ajustar la junta y repita la prueba de la solución
jabonosa and repeat the soap test.
6LORVFyGLJRVORFDOHVORSHUPLWHQVHSRGUiDJUHJDU
un cable a tierra externo (no provisto), ajustando el
mismo al tornillo conectado a tierra de color verde
en la parte trasera de la secadora, y a una conexión
FDxHUtDPHWiOLFDGHDJXDIUtDFRQHFWDGDDWLHUUDX
otra conexión a tierra establecida.
CONEXIÓN ELÉCTRICA INFORMACIÓN
SOBRE LAS SECADORAS A GAS
- Riesgo de Descarga Eléctrica
ADVERTENCIA
Enchufe en un tomacorriente con conexión a tierra
de 3 cables.
NO retire la conexión a tierra.
NO UTILICE un cable de extensión.
NO UTILICE un enchufe adaptador con este
artefacto.
6LQRFXPSOHFRQHVWRVHSRGUiSURGXFLUODPXHUWH
incendio o descarga eléctrica.
CÓMO CONECTAR UNA SECADORA A GAS (cont.)
Codo de metal de
µGHGLiPHWUR
Alivio de tensión de
3/4” (reconocido por
UL)
Abrazaderas de
tubería de 4” (2)
o abrazaderas de
resorte de 4” (2)
Gafas de seguridad
Conducto de metal
GHµGHGLiPHWUR
(recomendado)
Conducto de metal
flexible de 4”
GHGLiPHWUR
(si fuese necesario)
Guantes
Campana de salida
Cinta aislante
Kit de cable de
energía de la
secadora (no incluido
con la secadora)
Clasificado UL, de
120/240V, 30A con
3 o 4 patas. Identifique
el tipo de enchufe
según el tomacorriente
de la vivienda antes de
comprar el cable.
4” Placa de cubierta
(Kit WE1M454)
CÓMO CONECTAR UNA SECADORA ELECTRICA
(Sáltese si se trata de las secadoras a gas o si su secadora ya tiene un cable de alimentación conectado)
Instrucciones de instalación
9
Antes de efectuar la conexión eléctrica, desactive
los disyuntores o quite los fusibles del circuito
de la secadora de la caja eléctrica. Verifique
que el cable de la secadora esté desenchufado
del tomacorriente. NUNCA OLVIDE DE VOLVER
$&2/2&$5/$7$3$'($&&(62'(/%/248(
TERMINAL.
Pinzas
Destornillador de
lados planos
Destornillador Phillips
Nivel
MATERIALES NECESARIOS
HERRAMIENTAS NECESARIAS
10
CÓMO CONECTAR UNA SECADORA ELECTRICA (cont.)
Instrucciones de instalación
CONEXIÓN ELÉCTRICA INFORMACIÓN
SOBRE LAS SECADORAS ELÉCTRICAS
ADVERTENCIA
- Riesgo de incendio
Use un cable de suministro de corriente de la secadora
de 30 amperes y 240V de la lista de UL, con terminales
de anillo cerradas o terminales de espada con
extremos al revés.
Use un amortiguador con refuerzo de la lista de UL.
Desconecte la corriente antes de realizar conexiones
eléctricas.
Conecte el cable neutro (el blanco o el cable central) a
la terminal central.
(OFDEOHDWLHUUDYHUGHRSHODGRVHGHEHUiFRQHFWDUDO
conector a tierra verde.
Conecte los dos cables de suministro restantes a las
dos terminales restantes.
De forma segura ajuste todas las conexiones eléctricas.
Reemplace la tapa del bloque terminal.
6LQRFXPSOHFRQHVWRVHSRGUiSURGXFLUODPXHUWH
incendio o descarga eléctrica.
Para realizar conexiones eléctricas con
un cable de corriente:
CONEXIÓN ELÉCTRICA INFORMACIÓN
SOBRE LAS SECADORAS ELÉCTRICAS
Para conexiones directas de cables:
ADVERTENCIA
- Riesgo de incendio
Use un cable de cobre con calibre de 10
Use un amortiguador con refuerzo de la lista de UL.
Desconecte la corriente antes de realizar conexiones
eléctricas.
Conecte el cable neutro (el blanco o el cable central) a
la terminal central.
(OFDEOHDWLHUUDYHUGHRSHODGRVHGHEHUiFRQHFWDUDO
conector a tierra verde.
Conecte los dos cables de suministro restantes a las
dos terminales restantes.
De forma segura ajuste todas las conexiones eléctricas.
Reemplace la tapa del bloque terminal.
6LQRFXPSOHFRQHVWRVHSRGUiSURGXFLUODPXHUWH
incendio o descarga eléctrica.
INSTRUCCIONES DE CONEXIÓN A TIERRA
Para una secadora conectada con cable con
conexión a tierra:(VWDVHFDGRUDGHEHUiHVWDU
conectado a tierra. En caso de mal funcionamiento
RDYHUtDODFRQH[LyQDWLHUUDUHGXFLUiHOULHVJR
de descargas eléctricas al brindar un camino con
una resistencia menor para la corriente eléctrica.
(VWDVHFDGRUDHVWiHTXLSDGDFRQXQFDEOHFRQXQ
conductor para la conexión a tierra del equipo y un
HQFKXIHFRQFRQH[LyQDWLHUUD(OHQFKXIHGHEHUi
estar conectado a un tomacorriente instalado
en forma adecuada y con conexión a tierra de
acuerdo con todos los códigos y ordenanzas
locales.
Una conexión inapropiada del
conductor de conexión a tierra
del equipo puede provocar riesgos de descargas
eléctricas. Consulte a un electricista calificado o
personal o representantes del servicio técnico si
tiene dudas de que el electrodoméstico se encuentre
conectado a tierra apropiadamente. NO modifique
el enchufe en el cable de suministro de corriente. Si
no coincide con la toma de corriente, contrate a un
electricista calificado para que instale una toma de
corriente en forma adecuada.
GUARDE ESTAS INSTRUCCIONES
INSTRUCCIONES DE CONEXIÓN A TIERRA
Para una secadora conectada de forma
permanente: Esta secadora debe estar conectada
a un sistema de cableado de metal permanente
con conexión a tierra o se debe tender un
conductor para la conexión a tierra del equipo con
los conductores del circuito y ser conectado al
terminal de tierra del electrodoméstico.
Una conexión inapropiada del
conducto de conexión a tierra
del equipo puede provocar riesgos de descargas
eléctricas. Consulte a un electricista calificado
o personal o representantes del servicio técnico
si tiene dudas de que el electrodoméstico se
encuentre conectado a tierra apropiadamente.
GUARDE ESTAS INSTRUCCIONES
ADVERTENCIA
ADVERTENCIA
Instrucciones de instalación
11
CÓMO CONECTAR LA SECADORA
USANDO UNA CONEXIÓN DE 4 CABLES
(DEBE UTILIZARSE EN INSTALACIONES
DE CASAS RODANTES)
NOTA:
Desde el 1 de enero de 1996, el Código Eléctrico
Nacional exige que las nuevas construcciones utilicen una
conexión de 4 cables a una secadora eléctrica. También debe
usarse un cable de 4 alambres cuando los códigos locales no
permiten una conexión a tierra a través de cable neutral.
NO debe usarse una conexión de tres cables en una
construcción nueva.
CÓMO CONECTAR LA SECADORA
UTILIZANDO UNA CONEXIÓN DE 3 CABLES
1. Desactive el disyuntor (30 amperios) o quite el fusible
del circuito de la secadora de la caja eléctrica.
2. Verifique que el cable de la secadora esté
desenchufado del tomacorriente.
3.4XLWHODWDSDGHOFDEOHGHHQHUJtDXELFDGDHQODSDUWH
trasera inferior.
4. Instale un alivio de tensión de 3/4 pulgadas reconocido
por UL en el orificio de entrada del cable de energía.
Pase el cable de energía a través del alivio de tensión.
5. Conecte el cable de energía de la siguiente manera:
A. Conecte los dos cables vivos a los tornillos externos
del bloque terminal (marcado L1 y L2).
B. Conecte el cable neutral (blanco) al centro del
bloque terminal (marcado N).
6. Asegúrese de que la cinta de conexión a tierra esté
conectada a la terminal neutral (central) del bloque
y al tornillo verde de conexión a tierra de la parte
trasera del gabinete. Ajuste por firmemente todos los
tornillos (3) del bloque terminal.
7. Ajuste bien el cable de energía al alivio de tensión.
8. Vuelva a instalar la tapa.
Conexión de 3 cables
12XVDUHQ&DQDGi
NO usar en instalaciones en casas móviles.
NO usar en casas nuevas.
NO usar en vehículos recreativos.
12XVDUHQiUHDVGRQGHORVFyGLJRVORFDOHVSURKtEHQ
la connexión eléctrica a tierra por el medio del cable
neutral.
NUNCA OLVIDE DE VOLVER A COLOCAR LA TAPA
DEL BLOQUE TERMINAL.
NUNCA OLVIDE DE VOLVER A COLOCAR LA TAPA
DEL BLOQUE TERMINAL.
1. Desactive el disyuntor (30 amperios) o quite el fusible
del circuito de la secadora de la caja eléctrica.
2. Verifique que el cable de la secadora esté
desenchufado del tomacorriente.
3.4XLWHODWDSDGHOFDEOHGHHQHUJtDXELFDGDHQODSDUWH
trasera inferior.
4.4XLWH\GHVFDUWHODFLQWDGHFRQH[LyQDWLHUUD&RQVHUYH
el tornillo verde de conexión a tierra para el paso 7.
5. Instale un alivio de tensión de 3/4 pulgadas reconocido
por UL en el orificio de entrada del cable de energía.
Pase el cable de energía a través del alivio de tensión.
6. Conecte el cable de energía de la siguiente manera:
A. Conecte los dos cables vivos a los tornillos externos
del bloque terminal (marcado L1 y L2).
B. Conecte el cable neutral (blanco) al centro del
bloque terminal (marcado N).
7. Conecte el cable a tierra del cable de energía con el
tornillo verde de conexión a tierra (orificio sobre el
soporte de alivio de tensión). Ajuste por firmemente
todos los tornillos (3) del bloque terminal.
8. Ajuste bien el cable de energía al alivio de tensión.
9. Vuelva a instalar la tapa.
Si así lo requirieran los códigos locales, instale una conexión
a tierra externa (no provista) a metal con conexión a tierra,
tuberías de agua fría con conexión a tierra u otra conexión
a tierra establecida por un electricista calificado.
L1
N
L2
VUELVA A COLOCAR
EL TORNILLO VERDE
DE CONEXIÓN A TIERRA AQUÍ
SOPORTE
DE ALIVIO
BRACKET
CABLE VERDE
O AMARILLO
ALIVIO DE TENSIÓN
DE ¾” RECONOCIDO
POR UL
TORNILLOS
(3)
CABLE
VIVO
CABLE
VIVO
TAPA
NEUTRAL
(blanco)
4 CONDUCTORES DE COBRE #10 AWG
MÍNIMO O KIT DE CABLE DE SUMINISTRO
DE ENERGÍA DE 120/240V 30A MARCADO
PARA USO EN SECADORAS Y PROVISTO
CON TERMINALES DE BUCLE CERRADO O
DE PALA CON EXTREMOS HACIA ARRIBA
(NO PROVISTOS).
QUITE LA CINTA DE
CONEXIÓN A TIERRA
Y DESCÁRTELA. CONSERVE
EL TORNILLO VERDE
DE CONEXIÓN A TIERRA
L1
L2
SOPORTE
DE ALIVIO
DE TENSIÓN
ALIVIO DE TENSIÓN
DE ¾” RECONOCIDO
POR UL
CABLE VIVO
CABLE VIVO
CINTA DE CONEXIÓN
A TIERRA
TORNILLO
VERDE
DE CONEXIÓN
A TIERRA
NEUTRAL
(blanco)
TORNILLOS
(3)
TAPA
3 CONDUCTORES DE COBRE #10 AWG
MÍNIMO O KIT DE CABLE DE SUMINISTRO
DE ENERGÍA DE 120/240V 30A MARCADO
PARA USO EN SECADORAS Y PROVISTO
CON TERMINALES DE BUCLE CERRADO O
DE PALA CON EXTREMOS HACIA ARRIBA
(NO PROVISTOS).
SI ASÍ LO REQUIRIERAN LOS CÓDIGOS
LOCALES, INSTALE UNA CONEXIÓN
A TIERRA EXTERNA (NO PROVISTA)
A METAL CON CONEXIÓN A TIERRA,
TUBERÍAS DE AGUA FRÍA CON CONEXIÓN
A TIERRA U OTRA CONEXIÓN A TIERRA
ESTABLECIDA POR UN ELECTRICISTA
CALIFICADO.
Destornillador phillips
Cinta aislante o
abrazaderas de
tubería
Conducto de metal de
4” (10,2 cm) flexible o
rígido listado UL
Perfore con una
broca de 1/8” drill
bit (para ventilación
inferior)
Sierra para metales
Campana de
ventilación
Instrucciones de instalación
12
SALIDA AL EXTERIOR DE LA SECADORA
ADVERTENCIA
- Riesgo de incendio
Esta secadora DEBE tener una ventilación
al exterior.
Utilice sólo un conducto de metal rígido de 4” para
la
ventilación de salida doméstico.
Utilice
sólo un conducto de transición de metal rígido
de 4” o de la lista de UL para conectar la secadora a la
salida del hogar conducto.
NOXVHXQDYHQWLODFLyQGHOSOiVWLFR
NO use la salida de una chimenea, la salida de la
FRFLQDYHQWLODFLyQGHJDVSDUHGFLHORUDVRiWLFR
espacio de rastreo, o espacio escondido de una
edificación.
NO instale una pantalla en o sobre el conducto de
salida.
NOXVHXQFRQGXFWRPiVODUJRTXHDTXpOHVSHFLILFDGR
en la tabla de longitud de salida.
6LQRVHVLJXHQHVWDVLQVWUXFFLRQHVVHSRGUiSURGXFLU
la muerte o un incendio.
HERRAMIENTAS Y MATERIALES
NECESARIOS PARA INSTALAR UN
CONDUCTO DE SALIDA
CONEXIÓN DE LA SECADORA A LA
VENTILACIÓN DE LA CASA
CONDUCTO DE TRANSICIÓN DE METAL RÍGIDO
Para un mejor funcionamiento del secado, se
recomienda el uso de un conducto de transición de
metal rígido.
Los conductos de transición de metal rígido reducen el
riesgo de que se puedan aplastar o doblar.
CONDUCTO DE TRANSICIÓN DE METAL FLEXIBLE
SECADORA DE ROPA
DE LA LISTA DE UL
Si un conducto de metal rígido no puede ser
utilizado, entonces un conducto de metal flexible
aprobado por UL puede ser utilizado. (GE partes –
PM08X10085, WX08X10085 o WX08X10077.)

Nunca instale un conducto de transición en paredes,
cielos rasos, pisos u otros espacios adjuntos.
/DORQJLWXGWRWDOGHO
conducto de transición
QRGHEHUi
superar los 8’ (2.4 m).
3DUDPXFKDVDSOLFDFLRQHVVHUHFRPLHQGD
HQIiWLFDPHQWHODLQVWDODFLyQGHFRGRVWDQWRHQOD
secadora como en la pared. Los codos permiten
que la secadora pueda estar junto a la pared sin
que se aplaste ni se doble el conducto de transición,
maximizando el rendimiento del secado.
 (YLWHTXHODWXEHUtDVHDSR\HVREUHREMHWRVFRUWDQWHV
CONDUCTO DE TRANSICIÓN DE METAL FLEXIBLE (TIPO
HOJA DE ALUMINIO) DE LA LISTA DE UL
En instalaciones especiales, puede ser necesario
conectar la secadora a la ventilación domestica
usando un conducto de metal flexible (tipo papel
de aluminio). Un conducto universal flexible
aprobado por UL (GE partes - PM8X73 o WX8X73)
puede ser utilizado UNICAMENTE en instalaciones
donde un conductor de metal rígido o flexible no
SXHGHVHUXWLOL]DGR\GRQGHXQGLiPHWURGHµ
puede mantenerse a lo largo del conducto.
 (Q&DQDGi\HQ(VWDGRV8QLGRVVyORVHSRGUiQXVDUORV
conductos
de transición
que cumplan con “UL 2158A
STANDARD FOR CLOTHES DRYER TRANSITION DUCT
(UL 2158A - Norma de conductos para secadoras de
ropa).
(YLWHTXHODWXEHUtDVHDSR\HVREUHREMHWRVFRUWDQWHV
3DUDXQPHMRUIXQFLRQDPLHQWR
1. Deslice un extreme del conducto sobre la tubería
de salida de la secadora de ropa.
2. Asegure el conducto con una abrazadera.
3. Con la secadora en su posición permanente,
H[WLHQGDHOFRQGXFWRKDVWDVXPi[LPDH[WHQVLyQ
Permita que 2” del conducto se superpongan con
la tubería de escape. Corte y retire el sobrante del
FRQGXFWR0DQWHQJDHOFRQGXFWRORPiVUHFWR
SRVLEOHSDUDORJUDUHOIOXMRGHDLUHPi[LPR
4. Asegure el conducto a la tubería de escape con
la otra abrazadera.
Instrucciones de instalación
Al utilizar una salida de mayor longitud a la
especificada se:
 ,QFUHPHQWDUiQORVWLHPSRVGHVHFDGR\HOFRVWR
de energía.
 5HGXFLUiODYLGD~WLOGHODVHFDGRUD
 $FXPXODUiSHOXVDORTXHSRGUtDJHQHUDUXQ
riesgo potencial de incendio.
La correcta instalación de salida es SU
RESPONSABILIDAD.
Los problemas generados por una instalación
incorrecta no se encuentran cubiertos por
la garantía.
13
La longitud MÁXIMA PERMITIDA del sistema de
salida depende del tipo de conducto, la cantidad
de curvas, la clase de campana de salida (cubierta
de pared) y todas las condiciones indicadas en el
JUiILFR
 Codos internos agregados para conversiones
GHYHQWLODFLyQODWHUDORLQIHULRUVHGHEHUiQ
incluir en la cuenta total de los codos.
 Cualquier codo superior a 45º debería ser
considerado como un codo de 90º.

'RVFRGRVGHGHEHUiQVHUFRQVLGHUDGRVFRPRXQ
codo de 90°.
 Para cada codo adicional de 90°, reduzca en 10 pies la
longitud permisible del sistema de escape.
 (QHOFiOFXORGHODORQJLWXGWRWDOGHOVLVWHPDGH
ventilación, debe agregar todas las partes rectas
y codos del sistema (incluyendo el conducto de
transición).
LONGITUD DE SALIDA
NO doble o
pliegue los
conductos.
Utilice codos
si algunos
codos
resultan
necesarios.
NO utilice
una longitud
de salida
excesiva.
Corte los
conductos
con la
longitud
PiVFRUWD
posible.
NO
aplaste el
conducto
contra la
pared.
NO coloque
la secadora
en el
conducto.
CORTE el conducto lo
PiVFRUWRSRVLEOHH
LQVWiOHORGHUHFKRHQ
la pared.
UTILICE codos
cuando hagan falta
curvas.
Coudes
4" DIA.
4"
4" DIA.
4" DIA.
2-1/2"
LONGITUD MÁXIMA RECOMENDADA
Tipos de campana de salida
Recomendado
90 Pies
60 Pies
45 Pies
35 Pies
60 Pies
45 Pies
35 Pies
25 Pies
0
1
2
3
25 Pies 15 Pies4
Utilizar sólo en instalaciones
de trayecto corto
Cant. de
codos de 90°
Metal
Rígido
Metal
Rígido
LONGITUD DE SALIDA PARA
Lado de la pared
Lado
de la
secadora
Conducto de
transición
Instrucciones de instalación
14
ANTES DE COMENZAR
4XLWHODVSHOXVDVGHODDEHUWXUDGHVDOLGD
de la pared.
Abertura de
conducto
interno
Pared
Verifique que
el regulador de tiro
de la campana
de salida se abra
y cierre libremente.
SALIDA TRASERA ESTÁNDAR
Recomendamos instalar la secadora antes
que la lavadora. Esto permitirá un acceso directo
para poder efectuar la conexión de salida.
Deslice el extremo del conducto de salida hacia
la parte trasera de la secadora y sujete con cinta
aislante o una abrazadera de mangueras.
NOTA: Recomendamos el uso de un conducto
de salida rígido de metal. Si utiliza un conducto
semi-rígido de metal, córtelo con la longitud
DGHFXDGD\WUDWHGHTXHQRVHDSODVWHGHWUiV
de la secadora.
Para una instalación en línea recta, conecte
la salida de la secadora a la pared con cinta
aislante.
CONFIGURACIÓN RECOMENDADA
PARA MINIMIZAR LAS OBSTRUCCIONES
DE LA SALIDA
El uso de codos evitará que los conductos
se tuerzan y caigan.
Conducto
SALIDA AL EXTERIOR DE LA SECADORA (cont.)
CAMPANA O CUBIERTA DE PARED
Instale la salida de modo de evitar contracorrientes
RHOLQJUHVRGHSiMDURVXRWURVLQVHFWRVRDQLPDOHV
La boca de salida debe presentar una resistencia
mínima al flujo de salida y debe requerir poco
mantenimiento para evitar las obstrucciones.
Las cubiertas de pared deben instalarse por lo
menos a 12” sobre el nivel del suelo o cualquier
otra obstrucción con la abertura apuntando
hacia abajo.
SEPARACIÓN DE CURVAS
Para un mejor desempeño, separe todas las
curvas con 4 pies de conducto recto como
mínimo, incluyendo la distancia entre la última
curva y la cubierta de pared con regulador de tiro.
SELLADO DE JUNTAS
Todas las juntas deben estar bien selladas
para evitar pérdidas. El extremo macho de cada
sección de conducto debe apuntar en dirección
opuesta de la secadora.
Las juntas de los conductos deben ser herméticas
al aire y a la humedad mediante la superposición
de juntas con cinta aislante o cinta de aluminio.
No ensamble la tubería con tensores que se extiendan
sobre el conducto. Estos tensores acumulan pelusa,
creando un posible riesgo de incendio.
Los tramos horizontales deben tener una
inclinación hacia el exterior de 1/4” por pie.
Incluya un acceso para inspección y limpieza del
sistema de salida, especialmente en las curvas.
Inspeccione y limpie el conducto por lo menos una
vez al año.
AISLACIÓN
Los conductos instalados a través de una
iUHDVLQFDOHIDFFLyQRXELFDGRVFHUFDGHXQ
acondicionador de aire deben aislarse para reducir
la condensación y la acumulación de pelusas.
LISTA DE CONTROL DEL SISTEMA DE
SALIDA
Instrucciones de instalación
15
VENTILACIÓN LATERAL O POR LA PARTE
INFERIOR
La secadora cuenta con una salida hacia la
derecha del gabinete sólo en modelos eléctricos.
La secadora cuenta con una salida hacia la
izquierda del gabinete en modelos a gas y
eléctricos.
La secadora cuenta con una salida por
la parte inferior del gabinete en modelos
a gas y eléctricos.
Despegue y quite la tapa derecha (sólo modelos
a eléctrico), izquierda o por la parte inferior según
FRUUHVSRQGD4XLWHHOWRUQLOORXELFDGRGHQWURGHO
conducto de salida de la secadora y consérvelo.
Saque el conducto de la secadora.
Corte el conducto como puede verse y conserve
la porción A.
Porción “A”
Salida del lado
izquierdo
Orificio de montaje
UBICACIÓN DE LA LENGÜETA
Gire la lengüeta
hasta 45°
A través de la abertura trasera, ubique la lengüeta
en el medio de la base del artefacto. Levante la
lengüeta hasta alrededor de 45°, utilizando un
destornillador de lados planos.
No para gas
Orificio de montaje
A
13
1
ø2” (34.29 cm)
CÓMO AGREGAR UN CONDUCTO NUEVO
Cierre la abertura trasera con la placa protectora
(Kit WE1M454).
Desconecte la secadora del suministro eléctrico.
Use guantes y protectores para brazos.
6LHVWRQRVHFXPSOHVHSRGUiSURGXFLUXQD
incendio, descarga eléctrica o laceraciones.
ADVERTENCIA
- Riesgo de incendio
4XLWHHO
tornillo y
consérvelo
4XLWHODWDSD
deseada (sólo una)
Derecha
(sólo modelos
a eléctrico)
Izquierda
Parte
inferior
Vuelva a conectar la porción cortada “A” del
conducto a la caja del ventilador. Asegúrese de que
HOFRQGXFWRPiVFRUWRVHHQFXHQWUHDOLQHDGRFRQOD
lengüeta de la base. Utilice el tornillo conservado con
anterioridad para sujetar el conducto en su lugar a
través de la lengüeta de la base del artefacto.
CÓMO AGREGAR CODOS Y CONDUCTOS DE
SALIDA HACIA LA IZQUIERDA O DERECHA DEL
GABINETE
Arme previamente un codo de 4” con un
conducto de 4”. Coloque cinta aislante alrededor
de la junta.
Introduzca el montaje del conducto, el codo
primero, a través de la abertura lateral y conecte
el codo al conducto interno de la secadora.
Asegúrese de no tirar o dañar los cables eléctricos
ubicados dentro de la secadora cuando introduzca
el conducto.
La salida
puede
agregarse
a los lados
izquierdo
o derecha
(sólo
modelos a
eléctrico)
Cinta
aislante
Instrucciones de instalación
16
VENTILACIÓN LATERAL O POR LA PARTE
INFERIOR (cont.)
&RQHFWHORVFRGRV\FRQGXFWRVGHPHWDOHVWiQGDU
para completar el sistema de salida. Cubra
la abertura trasera con la placa (Kit WE1M454),
disponible en su proveedor de servicios local.
Coloque la secadora en su ubicación final.
Placa
(Kit WE1M454)
 Aplique cinta aislante
como puede verse en la
junta entre el conducto
interno de la secadora y
el codo, y también en
la junta entre el codo
y el conducto lateral.
Utilice sólo un conducto rígido de metal de un
diámetro de 4” dentro del gabinete de la secadora.
Las juntas del conducto interno deben sujetarse
con cinta; caso contrario, pueden separarse y
provocar un riesgo de seguridad.
NUNCA DEJE LA ABERTURA TRASERA
SIN LA PLACA EN SU LUGAR.
(Kit WE1M454.)
CÓMO AGREGAR LA PLACA DE CUBIERTA
A LA PARTE TRASERA DEL GABINETE
CÓMO AGREGAR CODOS Y CONDUCTOS
DE SALIDA HACIA LA IZQUIERDA O DERECHA
DEL GABINETE (cont.)
DUCT
TAPE
Cinta
aislante
Introduzca el codo a través de la abertura trasera
y conéctelo al conducto interno de la secadora.
Aplique cinta aislante
como puede verse en la
junta entre el conducto
interno de la secadora y
el codo, y también en la
junta entre el codo y el
conducto inferior.
Las juntas del conducto interno deben sujetarse
con cinta; caso contrario, pueden separarse y
provocar un riesgo de seguridad.
Cinta
aislante
CÓMO AGREGAR UN CODO DE SALIDA A TRAVÉS DE
LA PARTE INFERIOR DEL GABINETE
NIVELE LA SECADORA
Coloque la secadora en posición vertical cerca
de la ubicación definitiva y ajuste las cuatro patas
niveladoras para garantizar que la secadora
se encuentre nivelada de lado a lado y del frente
a la parte trasera.
Bajar
Elevar
ENCHUFE LA SECADORA
1
CONFIGURACIÓN FINAL
2
INICIO DE LA SECADORA
Presione el botón Power (Encendido).
NOTA: Si la secadora ha sido expuesta a temperaturas
bajo cero por un período prolongado, deje que suba
la temperatura antes de presionar Power. De otra
PDQHUDODSDQWDOODQRVHHQFHQGHUi
6XVHFDGRUD\DHVWiOLVWDSDUDXVDU
3
SALIDA AL EXTERIOR DE LA
SECADORA (cont.)
Verifique que haya
una conexión a tierra
adecuada antes del uso.
1 / 1

GE GFDN160GJWW Guía de instalación

Categoría
Secadoras de ropa eléctricas
Tipo
Guía de instalación

En otros idiomas