Samsung DV395GTPASU/A1-00 El manual del propietario

Marca: Samsung

Modelo: DV395GTPASU/A1-00

Categoría: Secadoras

Tipo: El manual del propietario

Este manual también es adecuado para

the possibilities

Thank you for purchastng thts SanqsLiiqg product

To receb'e more complete sePJice or accessory

parts please regtster your product at or

contact

www.samsung.com/register

1-8_J0-SAMSUNG _726-7864/

cont nt,

SAFETY iNSTRUCTiONS

iNSTALLiNG YOUR DRYER

OPERATING iNSTRUCTiONS, TIPS

CARE AND CLEANING

SPECIAL LAUNDRY TIPS

TROUBLESHOOTING

APPENDIX

3 What you need to know about Safety

Instructions

3 Important safety symbols and precautions

5 What to do if you smell gas:

7 Installation requirements

7 The dryer exterior

8 Ducting requirements

9 Important to installer

9 Location considerations

10 Alcove or closet installation

12 Exhausting

13 Gas requirements

13 Electrical requirements

14 Grounding

14 Electrical connections

15 Replacement parts and accessories

15 Tools Needed For Installation

16 Installation - General procedure

18 Final installation checklist

19 Dryer Exhaust Tips

20 Door Reversal

21 Connecting the inlet hose

22 Overview of the control panel

24 Child lock

25 Drum Light

25 Delay Start

25 My cycle

26 Vent Sensor

27 Smart Care

28 Rack Dry

29 Clean the lint filter

29 Load the dryer properly

29 Getting started

30 Control Panel

30 Tumbler

30 Stainless Steel Tumbler

30 Dryer Exterior

30 Dryer Exhaust System

31 Special laundry tips

32 Check these points if your dryer...

33 Information codes

34 Fabric care chart

35 Protecting the environment

35 Declaration of conformity

35 Specifications

36 Cycle chart

English - 2

safe nstrLActons

Congratulations on your new Samsung Dryer. This manual contains valuable

information on the installation, use, and care of your appliance. Please take the

time to read this manual to take full advantage of your dryer's many benefits and

features.

WARNING - Risk of Fire

• Clothes dryer installation must be performed by a qualified installer.

Install the clothes dryer according to the manufacturer's instructions and local codes.

Do not install a clothes dryer with flexible plastic venting materials. If flexible metal

(foil type) duct is installed, it must be of a specific type identified by the appliance

manufacturer as suitable for use with clothes dryers. Flexible venting materials are

known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

To reduce the risk of severe injury or death, follow all installation instructions.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

WARNING

CAUTION

Do NOT attempt.

Do NOT disassemble.

(_ Do NOT touch.

Follow directions explicity.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Hazards or unsafe practices that may result in severe personal injury or

death.

Follow the information in this manual to minimize the risk of fire or explosion or

to prevent property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids near this or

any other appliance.

Hazards or unsafe practices that may result in minor personal injury or

property damage.

SAVE THESE INSTRUCTIONS

English ° 3

n trLAction

IMPORTANT SAFTY INSTRUCTION

/_ WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your

......._ appliance, follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with

gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off

vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any flammable substance, such as

vegetable oil, cooking oil, machine oil, flammable chemicals, thinner, etc., or anything containing

wax or chemicals, such as mops and cleaning cloths. Flammable substances may cause the

fabric to catch fire by itself.

4. Do not store or use gasoline or other flammable vapors and liquids near this or any other

appliance.

5. Do not allow children to play on or in the appliance. Close supervision of children is necessary

when the appliance is used near children.

6. Before the appliance is removed from service or discarded, remove the door to the drying

compartment.

7. Do not reach into the appliance if the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with controls.

10. Do not repair or replace any part of the appliance or attempt any servicing unless specifically

recommended in the user-maintenance instructions or in published userrepair instructions that

you understand and have the skills to carry out.

11. Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

12. Clean the lint screen before or after each load.

13. Do not use heat to dry articles containing foam rubber or similarly textured rubberqike materials.

14. Keep area around the exhaust opening and adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

15. The interior of the appliance and exhaust duct should be cleaned periodically by qualified service

personnel.

16. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils

may contribute to a chemical reaction that could cause a load to catch fire.

17. This appliance must be grounded. See "Electrical requirements" and "Grounding" in installing your

dryer section.

Gas Appliances :

/_ WARNING :Tills product contains chemicals known to tile State of California to cause cancer and

w.%_-_.,,reproductive toxicity.

Gas appliances can cause low-level exposure to Proposition 65 listed substances, including but

not limited to, benzene, carbon monoxide, formaldehyde and soot, substances resulting from the

incomplete combustion of natural gas or LP fuels.

SAVE THESE INSTRUCTIONS

English ° 4

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not turn on the appliance.

Do not touch any electrical switch.

Do not use any phone in your building.

Clear the room, building or area of all occupants.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas

supplier.

_Read all instructions before the

using appliance.

To reduce the risk of fire or explosion:

WARNINe

Do not dry items that have been previously cleaned, washed, soaked, or spotted with

gasoline, dry cleaning solvents, or other flammable or explosive substances. They

emit vapors that could ignite or explode. Any material that has been in contact with a

cleaning solvent or flammable liquids or solids should not be placed in the dryer until all

traces of these flammable liquids or solids and their fumes have been removed.

There are many highly flammable items used in homes, such as acetone, denatured

alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,

turpentine, waxes, and wax removers

Items containing foam rubber (may be labeled latex foam) or similarly textured rubber-

like materials must not be dried on a heat setting. Heated foam rubber materials can,

under certain circumstances, produce fire by spontaneous combustion.

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is

necessary when the appliance is used near children and pets.

Before discarding or removing your dryer from service, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

Do not reach into the appliance when the drum is moving.

Do not install or store this appliance where it will be exposed to the weather.

Do not tamper with controls.

Do not repair, replace, or attempt to service any part of the appliance unless specifically

recommended in the user-repair instructions and you understand and have the skills to

carry those out.

Do not use fabric softeners or products to eliminate static unless recommended for dryer

use by the manufacturer of the fabric softener or product.

Clean the lint screen before or after each load.

Keep the area around the exhaust opening and surrounding areas free from lint, dust, and

dirt.

SAVE THESE INSTRUCTIONS

English o5

n tnA tion

The interior of the dryer and exhaust duct should be cleaned periodically by qualified service

personnel.

This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately and in accordance with local and national codes. See

installation instructions for grounding this appliance.

Do not sit on top of the dryer.

Because of continuing product improvements, Samsung reserves the right to change

specifications without notice. For complete details, see the Installation Instructions

packed with your product before selecting cabinetry, making cutouts, or beginning

installation.

Ensure pockets are free from small irregularly shaped hard objects, foreign material, etc. ie.

....... coins, knives, pins, etc. These objects could damage your dryer.

Do not wash clothing with large buckles, buttons, or other heavy metal or solid things.

Gas leaks may occur in your system, resulting in a dangerous situation.

WARNIN_

Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with the manufacturer's instructions.

Do not place items in your dryer that have been spotted or soaked with vegetable oil or

cooking oil. Evenafter being washed, these items may contain significant amounts of these

oils.

Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous

combustion increases when items containing vegetable oil or cooking oil are exposed to

heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction

in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become

hot enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat

from escaping and can create a fire hazard.

All washed and unwashed fabrics that contain vegetable oil or cooking oil can be

dangerous. Washing these items in hot water with extra detergent will reduce, but not

eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their

temperature. Never remove these items from the dryer hot or interrupt the drying cycle until

the items have run through the Cool Down cycle. Never pile or stack these items when they

are hot.

SAVE THESE INSTRUCTIONS

English ° 6

iNSTALLATiON REQUIREMENTS

Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup,

adjustment, and connection, it is considered the responsibility of the installer. If you install the dryer, you are

responsible.

Make sure you have everything necessary for proper installation.

1. A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements.

2. A POWER CORD for electric dryers (except Canada).

3. GAS LINES (if you have a gas dryer) must meet national and local codes.

4. EXHAUST SYSTEM - must be rigid metal or flexible stiff-walled metal exhaust ducting.

See the exhaust requirements on pages 8-10.

THE DRYER EXTERIOR

Control panel I

Door

Adjustable legs

INCLUDED ACCESORIES

"Y'-connector Short inlet hose Rubber Washer Long inlet hose

English o7

DUCTING REQUIREMENTS

Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

Do not use a smaller duct.

Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation.

Lint accumulation should be cleaned regularly.

If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct

with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sharply.

Never install any type of flexible duct in walls, ceilings, or other concealed spaces.

Only a rigid or flexible metal duct should be used for exhausting.

Keep the exhaust duct as straight and short as possible.

Secure joints with duct tape. Do not use screws.

DO NOT EXHAUST DRYER INTO ANY WALL, CEILING, CRAWL SPACE, OR CONCEALED SPACE OF

A BUILDING, GAS VENT, OR ANY OTHER COMMON DUCT OR CHIMNEY.

THIS COULD CREATE A FIRE HAZARD FROM LINT EXPELLED BY THE DRYER.

Do not use plastic flexible duct. Plastic flexible duct can kink, sag, be punctured, reduce airflow, extend

drying times, and affect dryer operation.

Exhaust systems longer than recommended can extend drying times, affect machine operation, and

may collect lint.

The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and

entry of wildlife. Never use an exhaust hood with a magnetic damper.

The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and

the ground or other obstruction. The hood opening should point down.

Never install a screen over the exhaust outlet.

To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house

or porch.

If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly

down towards the exhaust hood to reduce condensation and lint buildup.

,, Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before

cleaning.

,, Check frequently to be sure the exhaust hood damper opens and closes freely.

,, Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then

check ducting for obstructions.

Weather Hood Type

.... Recommended' use only for ShOrt-run installation

4" (10.16 cm)

No. of 90 ° elbows _ Rigid Metallic Flexible _

0 24.4 m (80 ft.) 12.4 m (41 ft.)

1 20.7 m (68 ft.) 11.2 m (37 ft.)

2 17.4 m (57 ft.) 10.1 m (33 ft.)

3 14.3 m (47 ft.) 9.0 m (29 ft.)

2.5" (6.35 cm)

Rigid ' Metallic FleXible*

22.6 m (74 ft.) 10.1 m (33 ft.)

18.9 m (62 ft.) 8.8 m (29 ft.)

15.5 m (51 ft.) 7.6 m (25 ft.)

12.5 m (41 ft.) 6.5 m (21 ft.)

* Do not use non-metallic flexible duct.

English o 8

If the new dryer is installed into an existing exhaust system you must make

sure:

The exhaust system meets all local, state, and national codes.

That a flexible plastic duct is not used.

To Inspect and clean all lint buildup from inside the existing duct.

The duct is not kinked or crushed.

The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be

less than 0.

This can be measured with the dryer running with a manometer at the point where the exhaust

duct connects to the dryer. A no-heat setting should be used. The dryer tumbler should be

empty and the lint filter clean.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept

for future reference.

/_ REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD

....... SUFFOCATING.

LOCATION CONSIDERATIONS

The dryer should be located where there is enough space at the front for loading the dryer, and enough

space behind for the exhaust system. This dryer is factory-ready for rear exhaust. To exhaust out the

bottom or the right or the left, use the accessory exhaust kit. Instructions are included with the kit. It's

important to make sure the room has enough fresh air. The dryer must be located where there is no air-flow

obstruction.

On gas dryers, adequate clearance as noted on the data plate must be maintained to ensure adequate air

for combustion and proper dryer operation.

THE DRYER MUST NOT BE INSTALLED OR STORED IN AN AREA WHERE IT WILL BE EXPOSED TO

WATER AND/OR WEATHER. THE DRYER AREA IS TO BE KEPT CLEAR OF COMBUSTIBLE MATERIALS,

GASOLINE, AND OTHER FLAMMABLE VAPORS AND LIQUIDS. A DRYER PRODUCES COMBUSTIBLE

LINT. THE AREA AROUND THE DRYER SHOULD BE KEPT LINT-FREE.

English o9

ALCOVE OR CLOSET INSTALLATION

MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:

Sides - 1 in / 25 mm Top - 17 in / 432 mm

Rear - 5 in / 127 mm Closet Front - 2 in / 51 mm

If the washer and dryer are installed together, the closet front must have at least a 72 in2

(465 cm 2)unobstructed air opening.

1 in.

(2.5cm)

-_ p,_-

_,© o

1in, -4_1"_-- 27in, ---_'11-_ 27in. _ 1in.

(2.5cm) (6&6cm) (68.6cm) (2.5cm)

17in.-_

(43.2cm)_

!i ::i i

2in. --_1_--- 31.9in.-----_1_--5in.

, (5cm) (81.1cm) (12.7cm)

A. Recessed area

B. Side view - closet or confined area

English ° 10

With optional pedestal base or stacking kit

Required Dimensions for Installation With Pedestal

< 61.7in.(131.4cm)toclearopendoor

(86.5cm) (12.7cm)

3 in,

_:i i!!__3io

ClosetorDoor ,_ (7.6cm)

I_ 39in.

(,991 ore,

:r ..... 53.6in.

• (136.2__cm),

_-_ 27in. _1

(66,6cm)

-_'_- 5in,

(12.7cm)

1 in. -N I 31 9 _n I _- 8in.**

(2.5cm) (81.1cm) (20.3cm)

Required Dimensions for Installation With Stacking Kit

6in.*

(18.2cm)

76in.

(198.1cm)

lin.-_--- 27in._

(2.6cm) ' (68.6cm)

* Required spacing

** External exhaust elbow requires

additional space.

English o 11

EXHAUSTING

The dryer shall not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a

building.

Exhausting the dryer to the outside will prevent large amount of lint and moisture from being blown into the room.

In the United States:

All dryer must be exhausted to the outside.

The required exhaust duct is 4 inches(10.2 cm ) in diameter.

Use only those foil-type flexible ducts, if any, specifically indentified for use with the appliance

by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct,

Subject 2158A, shall be used.

See "Ducting Requirements" in installing your dryer section for the maximum duct length and

number of bends.

The total length of flexible metal duct shall not exceed 2.4m.

Do not assemble the duct with screws or other fastening means that extend into the duct

and catch lint.

Canada:

All dryer must be exhausted to the outside.

The exhaust duct should be 4 inches(10.2 cm ) in diameter.

Use only those foil-type flexible ducts, if any, specifically indentified for use with the appliance

by the manufacturer shall be used.

See "Ducting Requirements" in installing your dryer section for the maximum duct length and

number of bends.

The total length of flexible metal duct shall not exceed 2.4m.

Do not assemble the duct with screws or other fastening means that extend into the duct

and catch lint.

Outside the U.S. and Canada:

Refer to the local codes.

A The dryer must be exhausted to the outside to reduce the risk of fire when installed in an

WAR.,N_alcove or closet.

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.

If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air,

heat, and lint.

English o 12

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL

CODES, WITH THE NATIONAL FUEL GAS CODE ANSVZ223.1, LATEST REVISION (FOR THE UNITED

STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP

(liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician.

A 1/2" (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8" (1 cm) gas

line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off

valve be installed within 6" of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.

Additionally, a 1/8" (0.3 cm) N.RT. (National Pipe Thread) plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of your dryer's gas supply connection.

Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the

system.

DO NOT reuse old flexible metal gas lines. Flexible gas lines must be design certified by the American Gas

Association (CGA in Canada).

[_ ny pipe joint compound used must be resistant to the action of any liquefied petroleum gas.

As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION - Your dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

Commonwealth of Massachusetts installation instructions

Your dryer must be installed by a licensed plumber or gas fitter. A "T" handle manual gas valve

must be installed in the gas supply line to your dryer. If a flexible gas connector is used to install

your dryer, the connector must have a maximum length of 3' (36").

- Gas leaks may occur in your system, creating a dangerous situation.

........ Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with the manufacturer's instructions.

ELECTRICAL REQUIREMENTS

} The

/k"

WARNING

wiring diagram is located on the back of the dryer.

Improperly connecting the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is

properly grounded. Do not modify the plug provided with your dryer - if it doesn't fit the outlet,

have a proper outlet installed by a qualified electrician.

To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding

must be done in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code

CSA C22.1 - Latest Revisions and local codes and ordinances. It is your responsibility to provide

adequate electrical services for your dryer.

All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 - Latest

Revision (for the U.S.) or CAN/CGA - B149 Installation Codes - Latest Revision (for Canada) and

local codes and ordinances.

English o 13

GROUNDING

This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of

electrical shock by providing a path of least resistance for the electrical current.

_ Gas models

WARNING

Your dryer has a cord with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer - if it doesn't fit the outlet, have a proper outlet

installed by a qualified electrician.

NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT

WATER PIPES.

Z_ Electric models

WARNING

Your dryer has a cord with an equipment-grounding conductor and a grounding plug, sold

separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer - if it doesn't fit the outlet, have a proper outlet

installed by a qualified electrician.

If a power cord is not used and the electric dryer is to be permanently wired, the dryer must

be connected to a permanently grounded metal wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment grounding

terminal or lead on the dryer.

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the Grounding section.

An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN

EXTENSION CORD.

Gas models- U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is

required.

Electric models- U.S. only

Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. The electric

service requirements can be found on the data label located behind the door. A 30-ampere fuse

or circuit breaker on both sides of the line is required.

If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

The power cord is NOT provided with U.S. electric model dryers.

English o 14

Risk of Electric Shock:

WARNIN_

When local codes allow, the dryer electrical supply may be connected by means of a new power

supply cord kit, marked for use with a dryer, that is U.L listed and rated at a minimum of120/240

volts, 30-ampere with three No. 10 copper wire conductors terminated with closed loop

terminals, open-end spade lugs with turned up ends, or with tinned leads.

Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring

must be supported at the dryer cabinet by a suitable UL-listed strain relief.

Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit

grounding through the neutral conductor. (Use a 4-prong plug for a 4 wire receptacle, NEMA

type 14-30R.)

Electric models - Canada Only

A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or

circuit breaker on both sides of the line is required.

All Canadian models are shipped with the power cord attached. The power cord should be

plugged into a 30-ampere receptacle.

[_lt not permissible to convert a dryer to

is in Canada 208 volts.

REPLACEMENT PARTS AND ACCESSORIES

If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your

dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864).

TOOLS NEEDED FOR iNSTALLATiON

Gather the required tools and parts before starting the installation.

Read and follow the instructions provided with any tools listed here.

Tools and Parts

Pliers Cutting knife Pipe wrench (gas only) Nut drivers

Level Phillips Screwdriver Duct tape Wrench

English o 15

INSTALLATION - GENERAL PROCEDURE

For proper installation, we recommend that you hire a qualified installer.

Read these instructions completely before you begin the installation.

To install the dryer, follow these steps:

t. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side-

by-side so you have easy access to both appliances.

To move the dryer easily, lay two of the carton cushion-tops on the floor. Tip your dryer on its side so it

lies across both cushion-tops. Push the dryer so that it is near its final location. Set your dryer upright.

Leave enough room around the dryer so you can attach the duct work, power cord, etc.

If you need to change the direction of the door, go to Door Reversal on page. When done, return to

Step 3 below.

Review the Exhausting section before installing the exhaust system. Install the duct work from your

dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO

NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic

flexible exhaust material.

A tip for tight installations: Attach a section of the exhaust system to your dryer before putting it in

place. Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at the

back of the dryer cabinet.

4. If you have an electric model, skip to Step 6. If you have a gas model, go to the next step.

5. Review the Gas Requirements section, then follow the lettered steps below.

a. Remove the pipe thread protective cap.

bo Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections.

The must be resistant to the action of

pipe joint compound

any

liquefied petroleum

gas.

co Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4" (1.9 cm)

female thread end of a flexible connector to the 3/8" (1 cm) male threaded end on the dryer.

do Securely tighten the gas line fitting over the threads.

eo Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles

appear, tighten the connections and recheck. DO NOT use an open flame to check for gas leaks.

fo Go to Step 6 on the next page

6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions

(Step 7) or 4 Wire system instructions (Step 8) below.

English o 16

7. Three Wire system instructions:

A. External ground connector

B. Neutral grounding wire (green/yellow)

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. sA" (1.9 cm) UL-listed strain relief

1. Loosen or remove the center terminal block screw.

2. Connect the neutral wire (white or center wire) of the power

cord to the center, silver-colored terminal screw of the

terminal block. Tighten screw.

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten the strain relief screws.

5. Insert the tab of the terminal block cover into your Dryer's rear panel slot.

Secure the cover with a hold-down screw.

Z_ If converting from a 4-wire electrical system to a 3-wire, you must connect the ground strap

_A_.,._to the terminal block support to ground the dryer frame to the neutral conductor.

8. Four

We recommend using Ring terminals. If you use Strap terminals, please ensure you install

them perfectly.

Wire System instructions:

External ground connector

Green or bare copper wire of power cord

sA" (1.9 cm) UL-listed strain relief

Center silver-colored terminal block screw

Neutral Grounding wire (green/yellow)

Neutral wire (white or center wire)

1. Remove the External ground connector screw.

2. Connect the ground wire (green or unwrapped) of the

power cord to the external ground connector screw. If

you want to connect B (Green or bare copper wire of

power cord) to the Neutral Post without assembling with A

(cabinet ground), call the service technician.

3. Loosen or remove the center terminal block screw.

4. Connect the neutral wire (white or center wire) of the power cord and the appliance ground

wire (green with yellow stripes) under the central screw of the terminal block.

5. Connect the other wires to the outer terminal block screws. Tighten screws.

6. Tighten the strain relief screws.

7. Insert the tab of the terminal block cover into your Dryer's rear panel slot.

Secure the cover with a hold-down screw.

We recommend using Ring terminals. If you use Strap terminals, please ensure you install

them perfectly.

English ° 17

U.S. MODELS:

/_ Riskof Electric Shock:

....... All U.S.models are produced for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the

neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled

construction, mobile homes, or if local codes do not permit grounding through neutral. Ifthe 4-wire system is

used, the dryer frame cannot be grounded to the neutral conductor at the terminal block. Refer to the following

instructions for 3- and 4-WIRE SYSTEM CONNECTIONS.

Remove the terminal block cover plate. Insertthe power cord with a UL-listed strain reliefthrough the hole provided in the

cabinet near the terminal block.

A strain reliefmust be used. Donot loosen the nuts already installed on the terminal block. Be sure they are tight. Use a 3/8"

(lcm) deep well socket.

Level

9. Connect the Water Inlet Hose. For instructions, go to Connecting the Inlet Hose

on page

10. Toensure that the dryer provides optimal drying performance, itmust be level.To

level the dryer, follow the lettered steps below:

a. Using a level,check ifthe dryer is level side to side and then front to back.

b. If the dryer is not level,adjust the leveling feet on the bottom of the dryer until

the washer is levelside to side and back to front. Turning the feet clockwise

retracts the feet. Turning the feet clockwise loosens and extends them.

[_ To set the dryer to the same height as the washer, fully retract the

levelingfeet by turning them counterclockwise, then loosen the feet

by turning them clockwise. Once the dryer is the same height as the

washer, follow the directions above to levelthe dryer.

Leveling feet

Retract fully Then loosen

[_ djust the leveling feet one/as much as necessary to levelthe dryer Extending the leveling feet more than

necessary can cause the dryer to vibrate.

11. Make sure allgas connections (on gas models), exhaust, and electrical connections are complete. Plug in your dryer, and

then check its operation by using the checklist below.

12. For GAS MODELS ONLY

The burner may not ignite initiallydue to air inthe gas line.Allowing your dryer to operate on a heat setting will purge the

line. Ifthe gas does not ignite within 5 minutes, turn your dryer off and wait 5 minutes. Be surethe gas supply to your

dryer has been turned on. Toconfirm gas ignition, check the exhaust for heat.

FINAL INSTALLATION CHECKLIST

[] The dryer is plugged into an electrical outlet and grounded proper_/.

[] The exhaust ductwork is hooked up and the joints are taped.

[] You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct.

[] The dryer is leveland is sitting firmlyon the floor.

[] For gas models: The gas isturned on and there areno gas leaks.

[] Start your dryerto codirm that it runs, heats, and shuts off.

English o 18

DRYER EXHAUST TiPS

/_ Plastic or non-metal flexible duct presents a potential fire hazard.

WARNING

1. Make sure your dryer is installed properly so it exhausts air

easily.

2. Use a 4" diameter rigid metal duct. Tape all joints, including

at the dryer.

Never use lint-trapping screws.

3. Keep ducts as straight as possible

(I I_

4. Clean all old ducts before installing your new dryer.

Be sure the vent flap opens and closes freely.

Inspect and clean the exhaust system annually.

Don't let a poor exhaust system slow drying by:

1. Restricting your dryer with a poor exhaust system.

2. Using a plastic, thin foil, or non-metal flexible duct.

3. Unnecessarily using long ducts that have many

elbows.

4. Having crushed or clogged ducts and vent.

English o 19

DOOR REVERSAL

t. Unplug the power cord.

2. Remove two door hinge

screws.

3. Lift the door and remove

it,

8. Reinsert the screw in the

other hole.

4. Remove a screw on the

Frame Front

5. Remove the two screws

on the opposite side of

the door hinge.

6. Remove two screws from

the holder lever.

7. Remove a screw from the

door hinge.

9. Reinsert the screw (Step

4) on the Frame Front

10. Place the door on the

other side and reattach it

to the dryer.

1t. Reattach the holder lever.

12. Reattach the screws in

the remaing holes.

English o 20

CONNECTING THE INLET HOSE

Method1 - Using the Y Connector and Long Hose

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.

1. Turn off the cold water faucet.

2, Ifyou havea washer water hose attached to the cold water faucet,

unscrew and remove the hose.

3, Ifspace permits, attach the brass female end of the "Y"connector to

the cold water faucet. Turn by hand until tight.

4, Attach the straight end of the long hose to the "Y' connector. Screw

on the hose coupling by hand until it is tight.

5, Using pliers, tighten the hose coupling with an additional two thirds

turn.

Do not overtighten. You can damage the coupling.

6, Attach the angled end of the long hose to the fill valve at the bottom

of the dryer's rear frame. Screw on the coupling by hand until it is

tight.

7, Using pliers, tighten the hose coupling with an additional two thirds

turn.

(_Do not overtighten. You can damage the coupling.

8, Attach the water hose to the other side of the "Y" connector. Screw

ctExhaust' J

on the hose coupling until it is tight. Using pliers, tighten the coupling with an additional two thirds turn.

Do not overtighten. You can damage the coupling.

9, Turn the water faucet on.

10, Check for leaks around "Y" connector, faucets, and hoses.

Do not overtighten, as itmay damage the coupling.

9, Check that the water faucets are on.

10, Check for leaks around "Y" connector, faucets and hoses.

Method2 - Using the Short Hose, Long Hose, and Y Connector

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.

Ifthe "Y" connector cannot be attached directly to the cold water faucet, then you must use the short hose.

1. Turn off the cold water faucet.

2, Ifyou havea washer water hose attached to the cold water faucet,

unscrew and remove the hose.

3, Attach the short inlet hose to the cold water faucet. Screw on the

coupling by hand until it is tight.

4. Using pliers, tighten the coupling with an additional two thirds turn.

_Do not overtighten. You can damage the coupling.

5, Attach the 'Y" connector to the stainless male end of the small hose.

Screw on the coupling by hand until it istight.

6. Using pliers, tighten the coupling with an additional two thirds turn.

(_Do overtighten, can damage coupling.

not You the

7, Attach the angled end of the long hose to the fill valve at the bottom

of the dryer rear frame. Screw on the coupling by hand until it is tight.

8. Using pliers, tighten the coupling with an additional two thirds turn.

(_Do not overtighten. You can damage the coupling.

9, Turn the water faucet on.

10, Check for leaks around "Y" connector, faucets, and hoses.

English o 21

op r t n tnA tion , t

Z_ To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFTY

....... INSTRUCTION before operating this appliance.

OVERVIEW OF THE CONTROL PANEL

Heavy Duty Perm Press

Bedding PLUS__!_-Tirne Dry

TT,.... //_y _\\ O°,_°ry

HeawDuty _ Normal _PermPress

_ ,-C_ Manual

,owo,.... //_?. _\\ o._Dry

SanitiZes_Q_i5 _ i . , _i_ZXir Fluff

Delicate Refresh

Wool .........._ _-_ \7' WrinkleAway

1 C_ veq _,y () }qgl5 ) 60mJ,,. ) louder

I (D Motebry Medium ( 50rain. 5

] E3 Normal rhy Medium Low {J} 401tlJn, D So_ef

C_ Less Dry () Low ? _0mJtl, )

(30ampr_y c_ Extra ow } 20 nia, L] off

®®® ® ® ®

* m,_a Haass,. f_rE_r_F,i,_i....

L_ Ve_Dry ( llgl, _ 60rain, [3 t_uder

C3 Mogegr_ Medm c} 50rain F3

C} Normal D,_ } Moa[url_ Low :? _llin, _ 5o_('r

L _ Le_5 Dry ( LOW _ 30mJt_, [3

C3 Dam 9 Dry _ Extra ow :120nir_, _3 Off

"Smar_ Cat_ _D u i(_t _Chlr_ o_k

Power

StarffPause

Power

Star,Pause

HeavyDuty_ Normal _Sanitize

_W_ Manual

Perm Press Tilse Dry

Towe's _k _-_Z'_u'ck Dry

Refilding_( r_ ( !_) l_ Air [luff _ VM(,yDoryi ........................Mr,d[m 50rain, _

Power

StarffPause

English - 22

(_) Load should be under 3 pounds. The Wool cycle of this machine

has been approved by Woolmark company for Total-Easy-Care Wool

_o, M,_ products, M0913 (DV405).

_The and DV398 models endorsed The Woolmark

DV393,DV395 are

not

by Company.

Sanitize - Sanitizes garments by infusing hightemperature heat deep into the fabric

during the drying cycle. Use this course to keep your bedding and curtainsclean through

sanitization.

Time Dry -Time Dryallows you to select the desiredcycle time in minutes.

Turn the Cycle Selector dialto Time Dry,then press the Adjust Time up arrow to set the drying

time.

Press the arrow repeatedh!to scroll through the time settings.

Quick Dry - Provides a 30 minute drying cycle.

Air Fluff-The Air Fluffcycle tumbles the load in roomtemperature air

Refresh - This cycle is best for smoothing out wrinkles and reducing odors from loads

consisting of one to four dry items. Inthiscycle, asmall amount ofwater is sprayed into the

dryer drum afterseveral minutes of tumbling withheat.

Wrinkle Away - The WrinkleAway cycle removeswrinkles from clothes stored inclosets,

etc. Itprovides awrinkle releasevia optimized steam care. You canchange the drying time.

(Minimum time :20 minutes) *Forbest results, load no more than 3 items.

[_ Overloading dryer may yield same

the not the results..

The display window shows the estimated time remaining in the cycle after the Start/

Pause button is pressed. The estimated time remaining may fluctuate as the cycle

progresses.

The Drying light will illuminate and remain lit until the cycle is complete.

When your dryer is in the cool-down phase, the Cooling light will illuminate.

When your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will illuminate.

When the cycle is complete, "END" appears in the display panel until the dryer door is

opened, the Power, Start/Pause is pressed or about 5 minutes have passed.

If your dryer is paused during a cycle, the indicator lights will blink until the Start/Pause

button is pressed.

Wrinkle Prevent -Wrinkle Prevent provides approximately 180 minutes of intermittent

tumbling in unheated air at the end of the cycle to reduce wrinkling. Press the Wrinkle

Prevent button to activate this feature.

The indicator light above the pad will illuminate when Wrinkle Prevent is selected.

The load is dry, and can be removed at any time during the Wrinkle Prevent cycle.

Mixed Load Bell - The mixed load bell that notifies you when the average dry level in

a load is damp dry (80 % dried).This lets you take garments that you don't want fully

dried or that dry quickly out of the dryer early while letting others continue to dry.

You can select this function in all Sensor Dry cycles except Wool and Sanitize.

The dry level selections are limited to Normal Dry, More Dry, and Very Dry.

Delay Start : Any cycle can be delayed for up to 24 hours in one-hour increments.

Displayed hour indicates the time at which tile cycle will be started (See page 27 for

datails)

My Cycle: Choose your favorite cycle including cycle, temp, dry level option, etc. (See

page 27 for details.)

Rack Dry : Rack Dry is available in the Time Dry cycle. Temperature will be set to Extra

Low only. (See page 29 for details.)

Adjust Time - Time can be added or subtracted from the automatically set times in the

Manua Drycydes Dry,OuickDry,huffcydes)

To add or subtract time from tile cycle, press tile Adjust Time arrow pad up or down

until tile desired time is displayed.

English o 23

To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles, press the

Dry Level button. An indicator light will illuminate next to the desired dryness level.

Press the button repeatedly to scroll through the settings. Larger or bulkier loads may

require the Very Dry or More Dry setting for complete dryness.

The Less Dry setting is best suited for lightweight fabrics or for leaving some moisture

in the clothing at the end of the cycle. Damp Dry is designed to partially dry items. Use

for items that lay flat or hang to dry.

To select the correct temperature for the load, press the Temp button. An indicator light

will illuminate next to the desired temperature. Press the button repeatedly to scroll

through the settings.

High - For sturdy cottons or those labeled Tumble Dry.

Medium - For permanent press, synthetics, lightweight cottons, or items labeled

Tumble Dry Medium.

Medium Low - For lower heat than Medium to dry synthetic or washable knit fabrics.

Low - For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.

Extra Low - Provides the lowest heated dry temperature possible.

When using Manual Dry cycles, you can adjust the drying time by pressing the Time

Selection button.

During the Sensory Dry cycle, the time light indicator is off because exact drying times

are determined by fluctuating humidity levels.

When the cycle is complete, a chime will sound.

If you selected the Wrinkle Prevent option, the chime will sound intermittently.

Adjust the volume of the chime or turn it off by pressing the Signal button.

Press the button repeatedly to scroll through the choices.

Press to pause and restart programs.

Press once to turn your dryer on, press again to turn it off. If your dryer is left on for

more than 10 minutes without any buttons being touched, the power automatically

turns off.

CHILD LOCK (_

Prevents children from playing with your dryer.

Setting/Releasing

To turn on or turn off the Child Lock, press both the Time and Signal buttons simultaneously for

3 seconds.

Child Lock Details

You can turn Child Lock on while your dryer is running.

Once you set the Child Lock function, no button, except for the Power button, will respond

until you turn off the Child Lock function.

The Child Lock indicator will be lit.

lf the dryer is powered on again, the Child Lock function stays on.

To turn off Child Lock, follow the instructions above.

[_ hen other buttons, except for the Power button, do not respond, check the Child Lock

indicator. If Child Lock is on, follow the instructions above to turn Child Lock off.

English ° 24

DRUM LIGHT ..0,.

Lights the dryer drum while the dryer is running.

Turning On and Off

To turn on or turn off the Drum Light, press and hold the Temp. button for 3 seconds. (DV405)

If you want to set or release the Drum Light, press both the Dry Level and Temp. buttons

simultaneously. (DV395/DV393)

You can turn the Drum Light on and off while your dryer is running and when it is stopped.

If you do not turn the Drum Light off within 5 minutes of turning it on, it is automatically

turned off.

DELAY START Q

You can set the dryer to start your course automatically at a later time, choosing a delay time. The hour

displayed indicates the time at which the course will be started.

1. Set your drying course.

2. Press the Delay Start button repeatedly until the delay time is set.

3. Press the Start/Pause button. The "Delay Start " indicator will be lit, and the clock will begin counting

down until it reaches the set time.

4. To cancel a Delay Start function, press the Power button and then turn the dryer on again..

MY CYCLE

Lets you select, save, and then activate a customized cycle that includes Dry Level, Temp option, etc. at a

later time.

To use My Cycle, follow these steps:

1. Push the My Cycle button. The My Cycle indicator lights.

2. Select the cycle you want to include using the Cycle Selector Dial.

3. Select and set the options (Dry Level, Temp, etc.)

(_ ach cycle has certain default options that are automatically set. To see these default

options, go to page 37.

4. Push the Start/Pause button. The cycle starts.

5. As the dryer moves through the cycle, it memorizes the cycle and the options.

6. To run this cycle again at a later time, press the My Cycle button. The dryer automatically

selects the saved cycle and options.

You can change the My Cycle settings by repeating the process above.

The dryer will use these settings the next time you choose My Cycle.

English o 25

op r t n tnA tion , t

VENT SENSOR

Your Samsung dryer is equipped with a Vent Sensor, which detects and notifies you when it is time to clean

the ductwork. Keep your dryer safe and efficient by cleaning the ducts when prompted.

The Vent Sensor detects any duct blockages

You can figure out whether there is a duct blockage from the "Vent Sensor _/,_="lamp of the

digital display.

0 The "Vent Sensor _/4_"

lamp is turned off.

i ii

The "Vent Sensor _"

lamp illuminates.

The "Vent Sensor _/_="

lamp blinks.

The ductwork is free from

blockages.

When a part of the duct

or the lint filter is blocked

by lint or a foreign object.

When the resistance is

high because the duct is

too long or bent.

When the duct is blocked

by lint or a foreign object.

When the resistance is

very high because the

duct is too long or bent

excessively.

Check the duct

connection and shorten

the duct and straighten it

if necessary.

Check the lint filter or

the duct and clean it if

necessary.

Check the duct

connection and shorten

the duct and straighten it

if necessary.

Check the lint filter or the

duct and clean it as soon

as possible.

In the LEVEL 2 state, this lamp blinks for 3 hours after the completion of the cycle. (If the wrinkle

prevention function is activated, this message is displayed for up to 3 hours.)

If the power button is pressed or the door is opened, the power is immediately turned off.

For more information about the duct installation, please refer to the "" section on page 8.

• Although the dryer is available even if the blockage message is displayed, the drying time

may be extended.

• If the LEVEL 1 message is displayed the first time the dryer is run after the installation,

check the connection and clean the duct. If the LEVEL 1 message appears even

after you have checked and cleaned the ducts, this may indicate that there are some

restrictions of the duct due to the length, condition, etc.

If this occurs, you can use the dryer normally and no countermeasures need to be taken.

However, the drying time may be extended or the drying performance may be degraded.

English ° 26

SMART CARE

This function enables you to check the status of the dryer using a smartphone.

1. Press and hold the Smart Care button for 3 seconds to use the

SmartbuttonsCaresincefUnctiOnyouturnWhenontheanerrordryer.OCCUrSor if you do not press any : ",

The error code history is deleted after using the function.

2. If the Smart Care function is activated, the LED on the window display

rotates for 2 or 3 seconds and then the Smart Care indicator is lit on ................. ............

the display. [ DiiL_i_

3. Run the Smart Care app on your smart phone. _ ...................

• The Smart Care function has been optimized for: Galaxy & iPhone series (cannot be supported for

some models).

4. Focus your smart phone's camera on the display panel of the dryer.

5. If the smart phone's camera is focused on the display panel of the dryer, the panel and error message is

automatically recognized and the error type and countermeasures are displayed on the smart phone.

6. If the smartphone fails to recognize the error code more than twice, please enter the error code

displayed on the display panel of the dryer manually into the Smart Care app.

[_ Downloading the Smart Care App

Download the Samsung Laundry App into your mobile phone from the

Android market or Apple App store. (Search word :Samsung Smart

Washer/Dryer)

[_ Precautions when using Smart Care

If light from a light bulb, fluorescent bulb, or lamp is reflected on the

display panel of the washing machine, the smartphone may not be able

to recognize the panel or error message easily.

If you hold the smartphone at too large an angle relative to the front of

the display panel, it may not be able to recognize the error code. For

best results, hold the smartphone so that the front of the panel and the

smartphone are parallel or nearly parallel.

_} The Smart Care function is not supported by the DV395 and DV393 models.

English o 27

ii!?iiiiiiiiii!i:iil¸iii!ii!iiiiiiiiii_il;i!iiiiiiiiili_i!iiii¸i¸i!iiiii¸iiiiiiiiiiii!i!ii!_i_i¸i!i¸ili!¸iiiiiiiiiiiiiiiiiii;iiiiiii;iiiiiii!iiiiiiiiiiii!iiii¸iiiiiiiiii!iil¸II

RACK DRY

Installing the drying rack

t, Open the dryer door.

2, Position the drying rack in tumbler, placing the front lip of the drying rack on the top of the lint

filter.

3, Place the rear legs in the two recessed areas of the dryer's back wall then push down the

middle of the drying rack to fix it in place.

4, Place the items to be dried on the rack, leaving space between them so air can circulate.

5. Close the dryer door.

6, Press the RACK DRY button in the Tiime Dry cycle and then select the time according to the

moisture and weight of the items. The drying rack can be also used with the Air Fluff cycle..

DryingRack

Washable sweaters

(block to shape and lay flat on rack)

Stuffed toys

(cotton or polyester fiberfilled)

Stuffed toys

(foam or rubber-filled)

Foam rubber pillows Air Fluff

Sneakers Air Fluff

/_ Drying foam rubber, plastic, or rubber on a heat setting may cause damage to the items

wA,'_.,,and lead to a fire hazard.

No rack is for the DV393 model.

drying provided

Extra Low (Time Dry cycle)

Air Fluff

English ° 28

CLEAN THE LINT FILTER

After each load. J

To shorten drying time.

To operate more energy efficiently. /

;7} Do not operate your dryer without the lint filter in place.

Frame Front

Door

LOAD THE DRYER PROPERLY

Place only one washload in your dryer at a time.

Mixed loads of heavy and lightweight fabrics will dry differently, which may result in lightweight fabrics

being dry while heavy fabrics remain damp at the end of a drying cycle.

Add one or more similar items to your dryer when only one or two articles of clothing need drying.

This improves the tumbling action and drying efficiency.

Overloading restricts tumbling action, resulting in uneven drying as well as excessive wrinkling of some

fabrics.

GETTING STARTED

1. Load your dryer loosely- DO NOT overload.

2. Close the door.

3. Select the appropriate cycle and options for the load (see pages 24, 26).

4. Press the Start/Pause button.

5. The dryer indicator light will illuminate.

6. The estimated cycle time will appear in the display.

The time may fluctuate to better indicate drying time remaining in the cycle.

. hen the cycle is complete, "End" will appear in the display.

Pressing Power cancels the cycle and stops your dryer.

The Drying, Cooling, and Wrinkle Prevent indicator lights will illuminate during those portions of the cycle.

Do not place anything on top of your dryer while it is running.

WARNINO

Take care that children's fingers are not caught in the door when closing it. This may result in injury.

WARNIN_

English o 29

CONTROL PANEL

Clean with a soft, damp cloth. Do not use abrasive substances.

Do not spray cleaners directly on the panel.

The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products.

Apply such products away from your dryer and wipe up any spills or overspray immediately.

TUMBLER

Remove any stains caused by crayon, ink, fabric dye (from new items such as towels or jeans), and so on

with an allpurpose cleaner.

Tumble old towels or rags to remove any remaining stain or cleaning substance.

Once these steps are followed, stains may still be visible, but should not transfer to subsequent loads.

STAINLESS STEEL TUMBLER

To clean the stainless steel tumbler, use a damp cloth with a mild, non-abrasive cleaner suitable for stainless

steel surfaces.

Remove the cleaner residue and dry with a clean cloth.

DRYER EXTERIOR

The entire dryer has a high-gloss finish. Clean with a soft, damp cloth. Do not use abrasive substances.

Protect the surface from sharp objects as they may scratch or damage the finish.

Do not place any heavy or sharp objects or a detergent box on the dryer. Keep them on the purchased

pedestal or in a separate storage box.

DRYER EXHAUST SYSTEM

Should be inspected and cleaned yearly to maintain optimum performance.

The outside exhaust hood should be cleaned more frequently to ensure proper operation.

English ° 30

LAndrv

I J I

SPECIAL LAUNDRY TIPS

Please follow the care label or manufacturer's instructions for drying special

items, if care label instructions are not available, use the following information as

a guide.

Bedspreads & Comforters

Blankets

Curtains & Draperies

Cloth Diapers

Down-filled Items (jackets,

sleeping bags, comforters,

etc.)

Pillows

Plastics (shower curtains,

outdoor furniture covers,

etc.)

Follow the care label instructions or dry on the Normal cycle and

High temperature.

Make sure the item is thoroughly dry before using or storing.

May require repositioning to ensure even drying.

Use Normal cycle and dry only one blanket at a time for best

tumbling action.

Make sure the item is thoroughly dry before using or storing.

Use the Perm Press cycle and medium temperature to help minimize

wrinkling.

Dry in small loads for best results and remove as soon as possible.

Use the Normal cycle and the High temperature settings for soft,fluffy

diapers.

Use the Normal cycle and medium temperature setting.

Adding a couple of dry towels shortens drying time and absorbs

moisture.

Use the Normal cycle.

Add a couple of dry towels to help the tumbling action and to fluff the

item.

DO NOT dry kapok or foam pillows in dryer.

Use the Time Dry cycle and the Low or Extra Low temperature

settings depending on the care label instructions.

THINGS TO AVOID PUTTING IN THE DRYER :

Fiberglass items (curtains, draperies, etc.).

Woolens, unless recommended on the label.

Vegetable or cooking oil-soaked items.

Foam Rubber (rug backs, stuffed toys, shoulder pads, etc.)

English ° 31

troL]beshootinG

CHECK THESE POINTS IF YOUR DRYER...

Doesn't run.

Doesn't heat.

Doesn't dry.

Is noisy.

Dries unevenly.

Has an odor.

Make sure the door is latched shut.

Be sure the power cord is plugged into a live electrical outlet.

Check the home's circuit breaker and fuses.

Press the Start/Pause button again ifthe door is opened during the

cycle.

Check the home's circuit breaker and fuses.

On a gas dryer, check that the gas supply is on.

Clean the lint filter and exhaust duct.

Dryer may have moved into the cool-down phase of the cycle.

Check all of the above, plus...

Be sure the exhaust hood outside the home can open and close

freely.

Check exhaust system for lint buildup. Ducting should be inspected

and cleaned annually.

Use a 4" rigid metal exhaust duct.

Do not overload. 1 wash load = 1 dryer load.

Sort heavy items from lightweight items.

Large, bulky items like blankets or comforters may require

repositioning to ensure even drying.

Check that the washer is draining properly to extract adequate water

from the load.

Load may be too small to tumble properly. Add a few towels.

Check the load for objects such as coins, loose buttons, nails, etc.

Remove promptly.

It is normal to hear the dryer gas valve or heating element cycle on

and off during the drying cycle.

Be sure the dryer is leveled properly as outlined in the installation

instructions.

It is normal for the dryer to hum due to the high velocity of air moving

through the dryer drum and exhaust system.

Seams, pockets, and other similarly heavy areas may net be

completely dry when the rest of the load has reached the selected

dryness level. This is normal. Select the More Dry setting if desired.

If one heavy item is dried with a lightweight load, such as one towel

with sheets, it is possible that the heavy item will net be completely

dry when the rest of the load has reached the selected dryness level.

Sort heavy items from lightweight items for best drying results.

Household odors from painting, varnishing, strong cleaners, etc.

may enter the dryer with the surrounding room air. This is normal as

the dryer draws the air from the room, heats it, pulls it through the

tumbler, and exhausts it outside.

When these odors linger in the air, ventilate the room completely

before using the dryer.

English o 32

Shuts off before load is dry •

Lint on clothes

Garments still wrinkled after

Wrinkle-Care

Odors remain in clothing

after Refresh.

Water drips from nozzle • This is steam condensation. The dripping water will stop after a short

when Steam-Care starts time.

Sprayed water is not visible • Sprayed water is difficult to see when the door is closed

during Steam-Care

INFORMATION CODES

Information codes may be displayed to help you better understand what is occurring with your Dryer.

Dryer load is too small. Add more items or a few towels and restart

the cycle.

Dryer load is too large. Remove some items and restart the dryer.

Make sure the lint filter is cleaned before every load. With some loads

that produce high amounts of lint, it may be necessary to clean the

filter during the cycle.

Some fabrics are lint producers (for example, a fuzzy white cotton

towel) and they should be dried separately from clothes that are lint

trappers (for example, a pair of black linen pants)

Divide larger loads into smaller loads for drying

Check pockets thoroughly before washing and drying clothes.

Small loads of 1 to 4 items work best.

Load fewer garments.Load similar-type garments.

Fabrics containing strong odors should be washed in a normal cycle.

tE Clogged Lint Screen

Vent is restricted

Invalid heating Temp when the dryer

is running.

dE Running the dryer with door open

dF Door is not closing properly

Unit detects a button is being

bE2 )ressed for over 30 secs or button is

stuck

FE Invalid power source frequency

Electronic Control Problem (Over

2E Voltage Error)

AE Electronic Control Problem

Communication Error)

Clean the screen or vent.

If the problem continues, call for service.

Call for service.

Close the door and then restart.

If the problem continues, call for service.

Call for service.

Make sure a button is NOT being pressed

continuously. Try restarting the cycle.

If the problem continues, call for service.

Try restarting the cycle.

If the problem continues, call for service.

Call for service.

For any codes not listed above, call 1-800-SAMSUNG (726-7864).

English o 33

a.ppendx

FABRIC CARE CHART

The following symbols provide garment care direction. The Clothing care labels include symbols for

washing, bleaching, drying, and ironing, or dry cleaning when necessary. The use of symbols ensures

consistency among garment manufacturers of domestic and imported items. Follow care label directions to

maximize garment life and reduce laundering problems.

iiii_i_i__?JJ__!!!!!i¸I_8_}_i_ _ il ¸i{ii_ __

!_ Normal

Permanent Press /

Wrinkle Resistant /

Wrinkle Control

Gentle/Delicates

HandWaah

• e_ Hot

Warm

• Cold

/b-l !ill

Any Bleach (when

needed)

Only Non-Chlorine

(color-sale)

Bleach (when needed)

Tumble Dry Cycle

Permanent Press/

Wrinkle Resistant/

Wrinkle Control

Gentle/Delicates

[] Line Dry/Hang to Dry

[] Drip Dry

Dry Flat

High

Medium

Low

O Any Heat

No Heat/Air

High

Medium

Low

Do Not Bleach

Do Not Tumble Dry

No Steam (added to

iron)

Do Not Iron

O Dry Clean

Do Not Dry Clean

Line Dry/Hang to Dry

Drip Dry

[] Dry Flat

** The dot symbols represent appropriate wash water temperatures for various items. The temperature

range for Hot is 105 ° -125 °F / 41 o_ 52 °C, for Warm 85 ° - 105 °F / 29 ° - 41 °C and for

Cold 60 ° - 85 °F / 16 ° - 29 °C. (Wash water temperature must be a minimum of 60 °F / 16 °C for detergent

activation and effective cleaning.)

English o 34

PROTECTING THE ENVIRONMENT

This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please

observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected

to a power source. Remove the door so that animals and small children cannot get trapped inside the

appliance.

DECLARATION OF CONFORMITY

This appliance complies with UL2158.

SPECI FICATIONS

Div Inches (cm) Div Inches (cm)

DIMENSIONS A. Height 39" (99.1) C. Depth with 49.6" (126.0)

door open 90 °

B. Width 27" (68.6) D. Depth 31.1" (78.9)

WEIGHT 123.5 Ib (56 kg)

5300 W (Elec.)

HEATER RATING 22000 BTU/hr (Gas)

WATER PRESSURE 20-116 psi (137-800kPa)

English o 35

a.ppendx

CYCLE CHART

(o : factory setting, : selectable)

Normal

HeavyDuty

PermPress

Bedding PLUS/

Seesor Dry Beddinq

Towels

SanEtize

DeBates

Wool

Manual Dry Quick Dry

Time Dry

WrinkleAway

Steam Cycles

Refresh

Cottons, Work clothes, Linen, Mixed loads 1_

Heavyfabrics such as jean, Corduroys, Heawwork clothes

Synthetic fabrics, Knits, Wrinkbfree cottons,

Permanent

Bulky items such asblankets, Sheets,Comforters, Pillows

Bathtowels and similaritems

Bedding, Curtains, Children, clothing

Underwear, Blouses, Lingerie

Formachine washabb and tumble dryable wool only

(Maximum amount : 31b}

Form, Rubber, Plastic _,

Smallloads

Any load

Shirts, Trouser,Blouses

Shirts,Trouser,Comforter, Pillows _,

Normal dry

Verydry (Nochange)

Normal dry

Normal dry (Nochange)

Normal o

Perrn Press

Bedding PLUS / •

Sensor Dry Bedding

Towels •

Sanitize •

Wool

Manual Dry Quick Dry

Wrinkle Away

Steam Cycles

Refresh

® ®

Load Size Recommendations

Large load : Fill the drum to about % full. Do not add items over this level as they need to tumble

freely.

Medium load : Fill the drum to about ½ full.

Small load : Fill the drum with 3_5 items, not more than X full.

* For best results, follow the load size recommendations for each dry cycle.

English o 36

warranV(LJ,S,A)

SAMSUNG DRYER

LiMiTED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) Year All Parts and Labor

Two (2) Years Control Board Parts

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the United States.

To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service

procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or

SAMSUNG's authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability

within the contiguous United States.

In-home service is not available in all areas.

To receive in-home service, product must be unobstructed and accessible to the service agent.

If service is not available, SAMSUNG may elect to provide transportation of the product to and from an

authorized service center.

SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein,

with new or reconditioned parts or products if found to be defective during the limited warranty period

specified above.

All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG.

Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is

longer.

This limited warranty covers manufacturing defects in materials and workmanship encountered in normal,

noncommercial use of this product and shall not apply to the following: damage that occurs in shipment;

delivery and installation; applications and uses for which this product was not intended; altered product or

serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning, or other

acts of nature or God; use of products, equipment, systems, utilities, services, parts, supplies, accessories,

applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG

that damage this product or result in service problems; incorrect electrical line voltage, fluctuations and

surges; customer adjustments and failure to follow operating instructions, maintenance and environmental

instructions that are covered and prescribed in the instruction book; product removal and reinstallation;

problems caused by pest infestations.

This limited warranty does not cover problems resulting from incorrect electric current, voltage or supply,

light bulbs, house fuses, house wiring, cost of a service call for instructions, or fixing installation errors.

SAMSUNG does not warrant uninterrupted or error-free operation of the product.

English o 37

EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS

OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR

PURPOSE.

NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT

TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.

SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE

SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES CAUSED BY THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF

THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES.

NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE

PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE.

WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS,

DAMAGE, OR INJURY TO PURCHASER AND PURCHASER'S PROPERTY AND TO OTHERS AND THEIR

PROPERTY ARISING OUT OF THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT.

THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL

PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation

of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This

warranty gives you specific rights, and you may also have other rights, which vary from state to state.

To obtain warranty service, please contact SAMSUNG at:

Samaung Electronics America, inc.

85 Challenger Road Ridgefield Park, NJ 07660

t-800-SAMSUNG (726-7864)

www.samsung.com/ca (English)

www.samsung.com/ca fr (French)

Visits by a Service Engineer to explain functions, maintenance or installation is not covered by warranty.

Please contact your Samsung call agent for help with any of these issues.

English o 38

SAMSUNG DRYER

LiMiTED WARRANTY TO ORIGmNAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) year part and labor

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the Canada.

To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service

procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or

SAMSUNG's authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability

within the Canada.