Tamaha RP-U200 Manual de usuario

Marca: Tamaha

Modelo: RP-U200

Categoría: Receptor

Tipo: Manual de usuario

PERSONAL RECEIVER

RP-U200

OPERATION MANUAL

MANUEL D’UTILISATION

U C A

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AM ST

USB PCM D.

DSP

POWER

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

VOLUMEMUTE

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

• Explanation of Graphical Symbols

The lightning flash with arrowhead

symbol, within an equilateral triangle,

is intended to alert you to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

you to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the cart/

apparatus combination to avoid injury

from tip-over.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

Please record the serial number of this system in the

space below.

Model:

Serial No.:

The serial number is located on the rear of the main

unit.

Retain this Owner’s Manual in a safe place for future

reference.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out

of your equipment by playing it at a safe level. One that lets

the sound come through loud and clear without annoying

blaring or distortion – and, most importantly, without

affecting your sensitive hearing.

Since hearing damage from loud sounds is

often undetectable until it is too late, YAMAHA

and the Electronic Industries Association’s

Consumer Electronics Group recommend you

to avoid prolonged exposure from excessive

volume levels.

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow

instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use

of this product in a residential environment will not result in harmful interference with other electronic devices. This

equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the

users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not occur in all installations. If this product is found to be the

source of interference, which can be determined by turning the product “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to

distributethis type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp.,

6660 Orangethorpe Ave. Buena Park, CA90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its

subsidiaries.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party:

Address:

Telephone:

Type of Equipment:

Model Name:

Yamaha Electronics Corp.,

6660 Orangethorpe Ave.

Buena Park, CA90620

714-522-9105

Receiver

RP-U200

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See the user manual instructions if interference to radio reception is suspected.

INTRODUCTION

Features

● This unit brings high-quality audio to your

computer

This unit is a multimedia amplifier that brings you a new

level of audio enjoyment. This unit has a USB port for

connection with a personal computer. The USB interface

allows remote control of this unit from your computer and

control of sound data sent from your computer.

● Equipped with a five-channel power amplifier

This unit has a five-channel power amplifier for

reproducing surround sound fields of Dolby Digital*,

DTS** and Yamaha CINEMA-DSP effectively. You can

enjoy a full-scale home theater sound simply by adding

the optional Yamaha speaker system NS-U40P and an

optional subwoofer to this unit.

● Equipped with Dolby Digital and DTS decoders

This unit reproduces multichannel sources encoded with

Dolby Digital* or DTS** faithfully by using the built-in

Dolby Digital and DTS decoders. You can now

experience the sound scale and the realistic sensation of

actual theaters in your home.

● The newly-developed Yamaha Near-Field Cinema

DSP (Digital Sound Field Processor)

Various DSP sound field programs allow you to select

the program suitable for the selected input source. You

can experience the sound fields of famous concert halls,

movie theaters, etc. around the world in your home. The

DSP sound effects are also available for headphone

listening.

● Compatible with various USB audio functions

This unit is compatible with the following audio signals

received via a USB connection:

multi-channel (two, four and six channels) audio, high

quality digital audio of 24 bit/48 kHz and Dolby Digital-

encoded signals. (Some operating systems and software

programs do not support this feature.)

● Various inputs/outputs and easy operation

This unit is equipped with various input and output

terminals for both analog and digital signals, making it

ideal as a control center for other audio equipment, such

as a personal computer, CD player and MD recorder.

The supplied remote control makes operation easy, and

the supplied Application Software allows control of this

unit from your computer including detailed settings.

● Compatible with Virtual Dolby Digital and DTS Virtual

5.1

By employing the Virtual 3D technology, this unit

reproduces multi-channel sources such as Dolby Digital

and DTS providing realistic surround effects even with

just two speakers.

About this manual

● This manual explains how to operate this unit. Refer to

the separate “SET UP MANUAL” for how to connect

this unit with other equipment, and to install the

Application Software, etc. to your computer from the

supplied CD-ROM.

● This manual mainly explains how to operate this unit

using the front panel of this unit and the supplied

remote control.

● When this unit and your computer are connected with

the USB cable, and the supplied Application Software is

installed on the computer, you can operate this unit

from the computer using the Application Software. Refer

to the online help of the Application Software for how to

use the Application Software.

The Application Software extends the use of this unit

with additional functions which cannot be used with the

front panel keys or the remote control. This manual

introduces those functions by the following style.

Example:

 Adjusting USB MIX LEVEL

When an input other than the USB terminal is selected,

you can listen to the mixed sound signals from the

selected input and from the USB terminal. Also, the

mixing ratio of the signals from the USB terminal can be

adjusted.

* Refer to the online help of the Application Software for

details.

This manual also offers brief explanations about the

functions available with the Application Software on page

22–27. Refer to the online help of the Application

Software for details of how to use the functions.

E-1

CAUTION................................ 2

OUTLINE OF THIS UNIT

Main features of this unit.............. 3

Dolby Digital and DTS .................. 4

Virtual 3D....................................... 5

Digital Sound Field Processing (DSP) .....

CONTROLS AND THEIR

FUNCTIONS

Front panel & Remote control...... 6

About the display.......................... 8

BASIC OPERATION

Playing a source ........................... 9

Using sound field programs ...... 11

Recording.................................... 12

ADVANCED OPERATION

Adjusting the speaker balance ...

Setting USB channel .................. 20

Operating this unit with the

Application Software.................. 22

APPENDIX

Troubleshooting ......................... 28

Specifications ............................. 31

CAUTION

OUTLINE OF

THIS UNIT

CONTROLS &

THEIR FUNCTIONS

BASIC

OPERATION

ADVANCED

OPERATION

APPENDIX

English

CONTENTS

Manufactured under license from Dolby Laboratories.

“Dolby”, “AC-3”, “Pro Logic” and the double-D symbol are

trademarks of Dolby Laboratories.

Confidential Unpublished Works. 1992–1997 Dolby

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued and

pending. “DTS”, “DTS Digital Surround”, are trademarks of Digital

LISTENING TO AN FM

BROADCAST

Tuning into an FM station........... 14

Using the presets........................ 16

LISTENING TO AN

FM BROADCAST

E-2

1. To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2. Install this unit in a cool, dry, clean place – away from

windows, heat sources, sources of excessive

vibration, dust, moisture and cold. Avoid sources of

humming (transformers, motors). To prevent fire or

electric shock, do not expose the unit to rain or water.

3. Never open the cabinet. If something drops into the

set, contact your dealer.

4. Do not use force on switches, controls or connection

wires. When moving the unit, first disconnect the

power plug and the wires connected to other

equipment. Never pull the wires themselves.

5. The openings on the unit cover assure proper

ventilation of the unit. If these openings are

obstructed, the temperature inside the unit will rise

rapidly; therefore, avoid placing objects against these

openings. To prevent fire or damage, install the unit in

a well-ventilated area.

To prevent fire or damage, be sure to allow a space of

at least 10 cm behind, 10 cm on both sides and 10 cm

above the top panel of the unit.

6. The voltage used must be the same as that specified

on this unit. Using this unit with a higher voltage than

specified is dangerous and may result in fire or other

accidents. YAMAHA will not be held responsible for

any damage resulting from use of this unit with a

voltage other than that specified.

7. Always set the volume to minimum before starting

audio playback. Increase the volume gradually to an

appropriate level after playback has been started.

8. Do not attempt to clean the unit with chemical solvents

as this might damage the finish. Use a clean, dry

cloth.

9. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding

that the unit is faulty.

10. When not planning to use this unit for a long period

(i.e., vacation, etc.), disconnect the AC power plug

from the wall outlet.

11.

To prevent lightning damage, disconnect the AC power

plug when there is an electric storm.

12. Grounding or polarization – Precautions should be

taken so that the grounding or polarization of

appliances is not defeated.

For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous if

engaged in a live socket outlet.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

IMPORTANT:

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug, proceed

as follows: The wire which is coloured BLUE must be

connected to the terminal which is marked with the

letter N or coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED. Making sure

that neither core is connected to the earth terminal of

the three pin plug.

For Canadian Customers

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

When this unit is turned off by pressing the power switch

on the front panel or the POWER key on the remote

control, this unit turns into the standby mode. In this

mode, this unit is designed to consume a small amount

of power. This unit’s power supply is completely cut off

from the AC line only when the AC power cord is

disconnected.

CAUTION:

Read this before operating this unit

E-3

English

OUTLINE OF THIS UNIT

English

OUTLINE OF

THIS UNIT

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AMST

USB PCM D.

DSP

SUPERWOOFER SYSTEM YST-SW45

HIGH CUTSTANDBY/ON

150Hz50Hz

VOLUME

100

Main features of this unit

Using Yamaha’s unique DSP technology, this unit can bring

excitement and realism to any audio source by simulating

the acoustic environments of concert halls, movie theaters,

and so on. With its stylish, vertical design, this unit allows

you to use various audio sources, including the built-in FM

tuner, your computer, CD player, MD or tape deck, as

shown below.

OUTLINE OF THIS UNIT

Although this unit can be used as part of a typical hi-fi

system, connecting it to your computer via the USB

terminal, and running the supplied Application Software,

allows you to remotely control this unit from your computer

and make some adjustments and settings.

CD player

MD recorder

etc.

This unit

Personal computer

Front speaker (L)

Front speaker (R)

* Refer to the separate “SET UP MANUAL” for

connections.

FM antenna

Subwoofer

Surround speaker (L)

Surround speaker (R)

Center speaker

E-4

OUTLINE OF THIS UNIT

Dolby Digital and DTS

This unit features a built-in Dolby Digital decoder and a DTS decoder for reproducing surround sounds of sources encoded

with Dolby Digital or DTS. With such state-of-the-art technologies, this unit can bring the same audio experience to your

home as they have brought to feature films in quality theaters around the world.

Take some time now to read more about these features and enjoy the new experiences this system brings to your home

theater.

 DTS (Digital Theater System)

Digital Surround

DTS was developed to replace the analog soundtracks of

movies with six discrete channels of digital soundtracks,

and it is now installed in many theaters around the world.

The DTS digital playback system changed the way we

experienced movies in theaters with six discrete channels

of superb digital audio. DTS technology, through intense

research and development, has made it possible to deliver

similar encode/decode discrete technology to home audio

surround-sound entertainment. DTS Digital Surround is an

encode/decode system which delivers six channels of

master-quality, 20-bit audio; technically, it offers 5.1

channels, which means 5 full-range (left, center, right and

two surround) channels, plus a subwoofer (LFE) channel

(as “0.1”). It is compatible with the 5.1 speaker

configurations that are currently available for home theater

systems.

 Dolby Surround

Dolby Surround uses four discrete channels and five

speakers to reproduce realistic and dynamic sound effects:

two main channels (left and right), a center channel for

dialog, and a surround channel for special sound effects.

The surround channel reproduces sound within a narrow

frequency range.

Most video tapes and laser discs include Dolby Surround

encoding, as do many TV and cable broadcasts. The Dolby

Pro Logic decoder built into this unit employs a digital

signal processing system that stabilizes each channel for

even more accurate sound positioning than is available

with standard analog processors.

 Dolby Digital

Dolby Digital is a digital surround sound system that

provides completely independent multi-channel audio to

you. Dolby Digital provides five full-range channels in what

is sometimes referred to as a “3/2” configuration: three front

channels (left, center and right), and two surround

channels. A sixth bass-only effect channel is also provided

for output of LFE (low frequency effect), or low bass effects

that are independent of other channels. (This is called the

“LFE channel”.) This channel is counted as 0.1, thus giving

rise to the term 5.1 channels in total.

The wide dynamic range of sound reproduced by the five

full-range channels and precise sound orientation by digital

sound processing provides listeners with excitement and

realism that have never been experienced before.

E-5

English

OUTLINE OF THIS UNIT

English

OUTLINE OF

THIS UNIT

Virtual 3D

FL C FR

RL RR

FL C FR

RL RR

Virtual speakers

Typical surround system Virtual 3D

Early sound

reflections

Reverberation

Direct sound

Surround sound typically requires several speakers

situated in front of and behind the listening position, which

requires a substantial amount of space that may not always

be available.

In addition to ordinary surround sound reproduction using

several speakers, this unit enables you to enjoy surround

sound effects with only two speakers by using Yamaha’s

unique “Virtual 3D” (three-dimensional) technology.

Virtual 3D, which is used by this unit’s sound field

programs, simulates the surround effect provided by

surround and center speakers, creating “virtual” surround

speakers, as shown, so even with only two front speakers,

you can still enjoy surround sound.

Digital Sound Field Processing (DSP)

When you listen to a performance in a concert hall, jazz

club, or other live music venue, you not only hear the direct

sound coming from the musical instruments and singers,

but also the “early reflections” and natural reverberation.

Early reflections are the initial sound waves that bounce off

the floor, ceiling, and walls. Natural reverberation is made

up of sound waves that gradually attenuate as they bounce

repeatedly off multiple surfaces.

Since the way you hear early reflections and reverberation

depends on the shape and size of the building as well as

the material and construction of the walls and ceiling, each

venue has its own unique “sound,” called its “sound field.”

At Yamaha, we have measured all the elements that make

up a typical sound field—direction and level of the

reflections, band-width characteristics, and delay times—at

famous concert halls and opera houses around the world.

The information gained in this process has been converted

into programs that can be reproduced using Yamaha’s DSP

technology. Using its on-board DSP, this unit can process

any audio source and recreate the atmosphere of the

original venue.

E-6

CONTROLS AND THEIR FUNCTIONS

1 Input selectors & indicators

These four keys, explained below, are used to select

the input source. The indicator of the selected source

lights up.

● PC key

This key selects your computer as the input source.

Pressing this key repeatedly selects the signals

received at the USB, digital (DIGITAL PC COAX IN or

DIGITAL PC OPT IN) or analog (ANALOG PC IN)

input. The DIGITAL PC OPT IN has priority over the

DIGITAL PC COAX IN, so if you connect to both inputs,

the signal received at the DIGITAL PC OPT IN is used.

CONTROLS AND THEIR FUNCTIONS

Front panel & Remote control

Front panel

Remote control

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AM ST

USB PCM D.

DSP

7 8

POWER

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

VOLUMEMUTE

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

● AUX1 key

This key selects the equipment connected to the

ANALOG AUX 1 IN or DIGITAL AUX 1 OPT IN

connector as the input source. Pressing this key

repeatedly selects the digital or analog input.

● AUX2 key

This key selects the equipment connected to the

ANALOG AUX 2 IN connectors as the input source.

● TUNER key

This key selects the built-in FM tuner as the input

source. If the tuner is already selected, this key toggles

the reception mode between FM auto stereo and FM

monaural.

E-7

English

CONTROLS AND THEIR FUNCTIONS

CONTROLS &

THEIR FUNCTIONS

2 Display

The display shows various settings, selected input

source, sound field program and various other

information.

3 DSP key [front panel]

ON/OFF key [remote control]

This key activates the sound field programs produced

by the internal DSP.

4 P-SET key ( ) [front panel]

PRESET key [remote control]

This key changes the display status of the built-in FM

tuner from the frequency display mode to the preset

tuning mode.

If the tuner is already in the preset tuning mode, each

press of this key changes the group of preset stations

(A, B, C, D, E).

* This key works only when the tuner is selected as the

input source.

5 / (Down/Up) keys

These keys are used for selecting sound field

programs, changing station frequencies, selecting

preset station numbers, etc.

6 Volume control [front panel]

VOLUME

(Down/Up) keys [remote control]

These control and keys adjust the speaker and

headphone volume. The volume cannot be adjusted

when this unit is in the standby mode.

7 Headphone jack

Stereo headphones can be connected to this mini-jack

for private listening, with Virtual 3D effects specifically

tailored for headphone listening.

8 Power switch ( ) [front panel]

POWER key [remote control]

Each click of this switch changes the status of this unit

between standby mode and power on.

* In the standby mode, this unit can be turned on

remotely from your computer, using the supplied

Application Software. Note that this unit uses a small

amount of power in the standby mode.

9 MEMORY key

This key is used to store a desired station in the

memory.

* This key works only when the tuner is selected as

the input source.

0 Sound field program selector keys

Each of these keys selects the corresponding sound

field program.

A TEST key

This key is used to output a test tone. The test tone is

used when adjusting the volume balance among all

speakers in the system including the virtual surround

speakers. (Refer to page 19 for details.)

B Custom keys (A, B, C)

These keys are available when this unit and your

computer are connected with the USB cable, and the

supplied Application Software is installed on the

computer.

Each of these keys can be programmed with a set of

commands (input selector, sound field program,

volume setting, etc.) by using the Application Software.

After storing, simply pressing each key will execute the

stored command.

* Refer to the online help of the Application Software for

details.

C MUTE key

This key is used to cut off sound output temporarily.

Turning the volume control on the front panel or

pressing the VOLUME keys on the remote control

restores sound output. Pressing this key again also

restores sound output.

* Sound output will also be restored by changing the

status of this unit between standby and power-on,

changing the input source or the sound field program,

and so on.

D MANUAL key

This key changes the display status of the built-in FM

tuner from the preset tuning mode to the frequency

display mode.

* This key works only when the tuner is selected as the

input source.

E Tuning /

(Down/Up) keys

These keys work in the following ways according to the

status of the tuner.

In the frequency display mode:

Each press of selects a higher frequency and

selects a lower frequency.

In the preset tuning mode:

Each press of selects a higher preset station

number and selects a lower preset station number.

E-8

CONTROLS AND THEIR FUNCTIONS

About the display

This section explains what the various display indicators mean.

1 VIRTUAL

This indicator appears when this unit is using Virtual 3D.

2 USB

This indicator appears when audio signals are sent or

received via the USB terminal.

* If you use a Macintosh computer, this indicator is

always illuminated when this unit is connected to the

computer via the USB terminals.

3 (DTS)

This indicator appears when an input signal is decoded

with DTS.

4 PCM

This indicator appears when a PCM digital audio signal

is selected as the input source.

This indicator appears when headphones are

connected to the headphone jack of this unit.

6 5.1CH

This indicator appears when a 5.1 channel digital audio

signal is selected as the input source.

7 DSP

This indicator appears when the DSP is processing the

input signal.

8 Sound output indicator

This indicator shows the currently used speakers. A red

dot shows that the corresponding speaker is currently

used, or the speaker is set for use in the Application

Software. The mark shows that sound is outputted.

* When using the test tone, a red dot shows the

channel currently outputting the test tone.

* When using headphones, only the two dots for the left

and right front speakers appear regardless of the

setting in “Speaker Settings”.

9 D.

This indicator appears when an audio signal encoded

with Dolby Digital is selected as the input source.

0 ST

This indicator appears when a stereo broadcast is

received in stereo mode.

A (DOLBY) DIGITAL

This indicator appears when an input signal is decoded

with Dolby Digital.

B (DOLBY) PROLOGIC

This indicator appears when an input signal is decoded

with Dolby ProLogic.

C FM

This indicator appears when the built-in FM tuner is

selected as the input source.

D Multi-information display

Various messages and information appear here.

E VOL (volume)

This indicator graphically displays the volume level

setting.

Note

The indicators , “5.1CH” and will not appear when

sound signals are decoded on the computer (by using DVD-

playback software, etc.).

VOL

VIRTUAL 5.ICH

DIGITAL

PROLOGIC FM ST

USB PCM D.

DSP

6542

E-9

BASIC OPERATION

English

BASIC

OPERATION

BASIC OPERATION

Playing a source

Start the selected input source.

Refer to “Listening to an FM broadcast” on pages 14–18

about how to tune into a desired station.

Adjust the volume to the desired level.

As you prefer, use a sound field program.

Refer to page 11 for details about the sound field programs.

About the input selector keys

Each of the input selector keys selects the following input signals.

PC: Press the PC key repeatedly to select the PC inputs:

“USB”, “PC_DIGT” and “PC_ANLG”. PC_DIGT selects

the DIGITAL PC COAX IN or DIGITAL PC OPT IN, and

PC_ANLG selects the ANALOG PC IN.

Note: The DIGITAL PC OPT IN has priority over the

DIGITAL PC COAX IN, so if you connect to both inputs,

the signal received at the DIGITAL PC OPT IN is used.

AUX1: Press the AUX1 key repeatedly to select the inputs:

“AUX1_DG” and “AUX1_AN”. AUX1_DG selects the

equipment connected to the DIGITAL AUX 1 OPT IN, and

AUX1_AN selects the equipment connected to the

ANALOG AUX 1 IN connector as the input source.

AUX2: Press the AUX2 key to select

the equipment connected to

the ANALOG AUX 2 IN

connectors as the input

source.

TUNER: Press the TUNER key to select the built-in FM tuner as

the input source.

* When the TUNER key is pressed, “TUNER” appears

first on the display, and then changes to the display of

a frequency or a preset station.

This section explains how to turn on this unit and select

input sources. If any external audio equipment is

connected to this unit, turn it on first.

Turn on this unit.

The message “Hello” appears for a few seconds, and this

unit returns to the state in which it was last used (e.g., the

input source that was selected when this unit was turned off

is selected).

Decrease the volume to minimum (MIN).

Select an input source by using the input selector

keys.

The corresponding indicator on the front panel lights up.

Refer to the explanation on the right side for details about

using the input selector keys.

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AMST

USB PCM D.

DSP

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

B CA

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

VOLUMEMUTE

POWER

2, 5

POWER

Front panel

Remote control

VOLUME

Front panel

Remote control

TUNER

AUX1

AUX2

TUNER

AUX1

AUX2

Front panel

Remote control

VOLUME

Front panel

Remote control

VOLVOL

VOL

FM ST

VOL

FM ST

E-10

BASIC OPERATION

Note

When the PC, AUX1 or AUX2 input selector key is pressed, the

display shows the name of the selected input source for a short

while, and then shows the currently selected sound field

program.

When no sound field program is selected, “THROUGH” is

shown on the display.

The names of input sources shown on the display can be changed

with the Application Software. Refer to the Online Help of the

Application Software for details.

 To cut off sound output temporarily

Press the MUTE key. To restore sound output, turn the

volume control on the front panel or press the VOLUME

keys on the remote control. Pressing the MUTE key again

also restores sound output.

Note

Sound output will also be restored by changing the status of this

unit between standby and power-on modes, changing the input

source or the sound field program, using the test tone, or using

the A, B, C keys on the remote control.

 When you listen with headphones

Connect the headphones to the headphone jack. No

sound will be outputted from the speakers.

 When you have finished using this unit

Set this unit to the standby mode by pressing the power

switch on the front panel or the POWER key on the remote

control.

Note

When not planning to use this unit for a long period (i.e.,

vacation, etc.), disconnect the AC power plug from the wall

outlet.

 Setting USB MIX

When an input other than the USB terminal is selected, you

can listen to the mixed signals from the selected input and

from the USB terminal. Also, the mixing ratio of the signals

from the USB terminal can be adjusted.

* Refer to the online help of the Application Software for details.

 Setting graphic equalizer

You can adjust the frequency characteristics as you prefer

by using the 7-band graphic equalizer.

* Refer to the online help of the Application Software for details.

Notes

● Some setting changes may be needed on the computer to

reproduce signals sent from the computer to this unit via the

USB connection. Refer to the separate “SET UP MANUAL”

for details.

● Some setting changes may be needed on the computer to

reproduce signals sent from the computer to this unit via a

sound card, etc.

Automatic power saving function

If there is no operation on this unit’s front panel, the

remote control or the Application Software for about 24

hours with the power of this unit on, this unit will

automatically be set to the standby mode.

MUTE

Remote control

POWER

Front panel

Remote control

E-11

BASIC OPERATION

English

BASIC

OPERATION

Using sound field programs

This unit’s built-in DSP (Digital Sound field Processor) can simulate various acoustic environments, including a concert hall

and movie theater, with its seven sound field programs. For the best results, choose a program appropriate for the selected

audio source.

First follow steps 1–5 of “Playing a source” on page 9.

Turn on the DSP.

(When using the

remote control,

step 1 can be

skipped.)

The name of the selected sound field program appears on

the display.

Select the desired sound field program.

Front panel: Pressing or repeatedly changes the

program.

Remote control: Press the key of the desired program.

The following programs are available.

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AMST

USB PCM D.

DSP

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

B CA

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

VOLUMEMUTE

POWER

DSP

Front panel

JAZZ CHURCHHALL

MOVIE LIVEGAME

TEST

OFF

/DTS

SURROUND

Front panel

Remote control

VOL

DSP

Active program

Program

HALL (CONCERT HALL

EUROPE)

JAZZ (JAZZ CLUB

VILLAGE GATE)

CHURCH (CHURCH

ROYAUMONT)

GAME (GAME

AMUSEMENT)

MOVIE (MOVIE THEATER)

LIVE (LIVE CONCERT)

NORMAL ( DTS SUR.)

[HP3D*

(Headphone 3D)

]

Feature

This program simulates the sound field of a medium-

sized hall, with a beautiful and rich reverberation.

This program simulates the sound field of a famous

New York jazz club.

This program simulates the sound field of a Gothic

church, with the unique effect of sound reverberating

back and forth in a domed ceiling.

This program adds depth and surround effects to

computer games, enhancing the gaming experience.

The realism provided by this program gives the

impression that you’re actually in the scene.

This program produces an enthusiastic atmosphere

and lets you feel that you are in the midst of the

action, as if attending an actual jazz or rock concert.

This program reproduces the surround sound of a

source encoded with Dolby Pro Logic, Dolby Digital

or DTS faithfully. Sensing the input signal, the built-in

Dolby Digital decoder or the DTS decoder

automatically works.

When this unit is set to the “Virtual 3D” mode (the

surround speakers are not used) in the Application

Software, 5.1-channel surround sound effects are

reproduced with only two front speakers by using

Yamaha’s “Virtual 3D” technology.

Note

These programs create a sound

field that feels real, just as if you

were actually there.

These programs can be used

together with Dolby Pro Logic,

Dolby Digital or DTS for enjoying

surround sounds of motion-

picture audio.

: HP3D

This program enables you to

enjoy a virtual 3D effect with

headphones. When you

connect headphones to this

unit, the DTS SUR.

program automatically

changes to HP3D .

Hi-Fi DSP (for music sources)

CINEMA DSP (for video sources)

E-12

BASIC OPERATION

First turn on the external unit to be used, and then this

unit.

Select the source to be recorded by using the

input selector keys.

Start recording on a recording unit (an MD

recorder, tape deck, etc.).

Start playing the input source .

 Playing the recorded result via this unit

Select the input signals sent from the recording unit with

the input selector keys.

Notes

● If input signals received at any digital input terminal other

than the USB terminal is outputted at the digital output

terminal, the sampling frequency for the output signals is the

same as that for input signals.

● The sampling frequency for digital signals converted from

analog signals on this unit is 44.1 kHz or 48 kHz.

● When digital input signals are outputted at the digital output

terminal, track information (CD-text data, automatic track

renewal when recording is made on an MD, etc.) is invalid if

any sound field program (including the graphic equalizer

effect) is used.

● Both REC OUT and OPT OUT terminals on the rear of this

unit output the same constituents of signals as outputted from

the left and right front speakers.

Recording

Input sources (e.g., a computer or CD player) selected on

this unit can be recorded by an MD recorder, tape deck,

etc. connected to this unit. Also, input signals can be fed to

your computer via the USB connection.

* When a source is recorded using a sound field

program, sound field effects are recorded with the

source.

 Recording on an external recording unit

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AMST

USB PCM D.

DSP

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

B CA

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

VOLUMEMUTE

POWER

TUNER

AUX1

AUX2

TUNER

AUX1

AUX2

Front panel

Remote control

Notes

● Just after selecting a program, the program name scrolls from

right to left on the display, and then its short-version name

lights up.

● No sound field program can be used when receiving signals

with a 96 kHz sampling frequency.

OFF

DSP

Front panel

Remote control

 To turn off the sound field effect

Press the DSP key on the front panel or the ON/OFF key on

the remote control. “THROUGH” appears on the display.

Note

When the sound field effect is off, sound is reproduced in normal

stereo.

 Adjusting DSP sound field parameters

The surround effect of each program or the Virtual 3D effect can

be adjusted to the desired taste by using the Application

Software. Refer to the online help of the Application Software

for details.

E-13

BASIC OPERATION

English

BASIC

OPERATION

 Recording on a computer (via the USB connection)

Select the source to be recorded by using the

input selector keys.

Start recording with the recording software on the

computer.

Start playing the input source.

 Playing the recorded result via this unit

Press the PC input selector key repeatedly to select USB as

the input source, and play the recorded result on the

computer.

Notes

● If the number of USB channels is set to six, recording cannot

be made via the USB connection. Reset the number of USB

channels to two or four.

● To record digital input signals with a 48 kHz sampling

frequency, the frequency of the input signals must be 48 kHz.

● To record sound signals received at an analog or digital input

of the sound card etc., and not via the USB connection, select

the corresponding device, such as “Sound Card”, from

“Preferred device” of “Recording” (or “Sound Recording”)

on the computer.

● The sampling frequency and resolution of signals recordable

on the computer differ from operating systems. You can refer

to the following Yamaha website for details about the related

information.

http://www.yamaha.co.jp/audio/

TUNER

AUX1

AUX2

TUNER

AUX1

AUX2

Front panel

Remote control

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AMST

USB PCM D.

DSP

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

B CA

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

VOLUMEMUTE

POWER

When recording or processing signals inputted to your

computer via the USB connection, the following setting is

needed on the computer.

 Selecting Recording Device

When using Windows

1. Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

2. Double-click the “Multimedia” icon (or the “Sounds

and Multimedia” icon).

3. Click the “Audio” tab and select “USB Audio Device”

at “Preferred device” of “Recording” (or “Sound

Recording”).

When using a Macintosh

Select “USB Audio” as the input device at “Sound” on

the Control Panel.

 Setting of Recording Software

Select a sampling frequency from 44.1 kHz and 48

kHz. Select a resolution from 16 bits and 24 bits. The

sampling frequency of 44.1 kHz with the resolution of

16 bits produces a sound quality comparable to the

compact disc (CD).

Notes

● Please check the copyright laws in your country before recording compact discs, radio, etc. Recording of copyright

material may infringe copyright laws.

● You cannot make a recording from a CD-R, MD, etc. which is a copy of an audio CD, to another CD-R, MD, etc. via the USB

connection or the digital terminal connection. Also, you cannot make a recording from an MD which is recorded with digital

signals received via the USB connection, to another MD via a digital connection.

E-14

LISTENING TO AN FM BROADCAST

Tuning into an FM station

Normally, if station signals are strong and there is no interference, quick auto tuning is possible. However, if the signal of the

station you want to select is weak or the reception condition is bad, you must tune in to it manually.

Auto tuning

First turn on this unit.

Press the TUNER input selector key to select the

built-in FM tuner.

The tuner turns on in either of the following modes. (The

mode which was selected the last time you used the tuner is

selected.)

● Frequency display mode

The display shows the

selected frequency. This

mode is for tuning into a

station by changing the

frequency.

● Preset tuning mode

This mode is for tuning into a

preset station which is

already stored in the memory.

The display shows the preset

group (A to E), the number (1

to 8) and the frequency of the

preset station.

If the tuner is in the preset tuning mode, press the

TUNER key (front panel) or the MANUAL key

(remote control) to change the preset tuning mode

to the frequency display mode.

Press the TUNER key (front panel) or the MANUAL

key (remote control) to select the desired

reception mode: FM auto stereo or FM monaural.

The reception mode changes alternately by each press of the

TUNER key.

● FM auto stereo

When a stereo broadcast is received, it is received in

stereo automatically. (The “ST” indicator lights up on

the display.) If, however, the signal of a stereo

broadcast is weak, it may be received in monaural

automatically. (In this case, the “ST” indicator goes

off.)

● FM monaural

Any broadcast is received in monaural. (On the display,

“M” appears above the frequency.) If you hear noise in

the FM auto stereo mode, try switching to FM

monaural.

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AMST

USB PCM D.

DSP

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

B CA

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

VOLUMEMUTE

POWER

1, 2,

TUNER

AUX1

AUX2

TUNER

AUX1

AUX2

Front panel

Remote control

VOL

FM ST

VOL

FM ST

TUNER

AUX1

AUX2

MANUAL

Front panel

Remote control

VOL

FM ST

VOL

FM auto stereo

FM monaural

TUNER

AUX1

AUX2

MANUAL

Front panel

Remote control

(U.S.A. model)

E-15

LISTENING TO AN FM BROADCAST

English

LISTENING TO AN

FM BROADCAST

Press the or key and keep it pressed for one

second or more.

Press the key to search for lower frequencies and the

key for higher frequencies. When a station with a strong

signal is found, the search stops and the station is received.

If no station with a strong signal is found, the search stops

after searching through all frequencies.

If the received station is not the desired one,

repeat step 4.

Note

If the desired station cannot be found by the auto tuning method,

search for the station by using the manual tuning method.

Manual tuning

First turn on this unit.

Press the TUNER input selector key to select the

built-in FM tuner.

If the tuner is in the preset tuning mode, press the

TUNER key (front panel) or the MANUAL key

(remote control) to change the preset tuning mode

to the frequency display mode.

Press the TUNER key (front panel) or the MANUAL

key (remote control) to select the desired

reception mode: FM auto stereo or FM monaural.

Press the or key repeatedly until the

desired frequency is located.

Press the key to search for lower frequencies and the

key for higher frequencies.

Front panel

Remote control

TUNER

AUX1

AUX2

TUNER

AUX1

AUX2

Front panel

Remote control

TUNER

AUX1

AUX2

MANUAL

Front panel

Remote control

Front panel

Remote control

Frequency range and tuning step

Frequency range

Tuning step

U.S.A. and Canada

models

87.50–107.90 MHz 0.20

U.K. and Europe

models

87.50–108.00 MHz 0.05

Australia model 87.50–108.00 MHz 0.10

TUNER

AUX1

AUX2

MANUAL

Front panel

Remote control

E-16

LISTENING TO AN FM BROADCAST

Using the presets

You can store your favorite stations in the 40 presets, which are organized into five groups (A–B), with eight presets in each

group. A stored station can be recalled simply by selecting the preset number in which it is stored.

Storing stations manually

First turn on this unit, and then select the built-in FM tuner

as the input source.

In the frequency display mode, tune into the

desired station and select the reception mode: FM

auto stereo or FM monaural.

* Refer to pages 14 to 15 on how to tune into a station and

select the reception mode.

Press the P-SET key (front panel) or the MEMORY

key (remote control) and keep it pressed for one

second or more.

A preset group and a preset number appears and an arrow

scrolls from right to left on the display. This means that

storing a station is possible.

Press the P-SET key (front panel) or the PRESET

key (remote control) repeatedly to select the

desired preset group from A through E.

Press the key or the key repeatedly to select

the desired preset number from 1 through 8.

Press the P-SET key (front panel) or the MEMORY

key (remote control) and keep it pressed for one

second or more.

“MEMORY” lights up on the display for approx. 2

seconds to show that the station has been stored.

Notes

● A newly stored station overwrites the previously stored one in

the same preset group and number.

● To abort storing the station, press an input selector key

(except the TUNER key). The selected input mode appears.

With the supplied Application Software, you can use the auto

preset tuning function in addition to the manual method. The

auto preset function searches for all stations available in your

area and automatically stores them in the presets.

Also, the Application Software allows you to assign a name to

each preset station. The names are displayed on the monitor

when running the Application.

Refer to the online help of the Application Software for details.

Front panel

Remote control

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AMST

USB PCM D.

DSP

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

B CA

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

VOLUMEMUTE

POWER

2, 5

2, 3, 5 4

MEMORY

P-SET

Front panel

Remote control

VOL

FM ST

Preset numberPreset group

PRESET

P-SET

Front panel

Remote control

MEMORY

P-SET

Front panel

Remote control

(U.S.A. model)

E-17

LISTENING TO AN FM BROADCAST

English

LISTENING TO AN

FM BROADCAST

Recalling a preset station

First turn on this unit, and then select the built-in FM tuner

as the input source.

Press the P-SET key (front panel) or the PRESET

key (remote control) to change this unit from the

frequency display mode to the preset tuning

mode.

Press the P-SET key (front panel) or the PRESET

key (remote control) repeatedly to select the

preset group from A through E.

Press the key or the key repeatedly to

select the preset number from 1 through 8.

The station stored in the selected preset group and number is

selected.

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL 5.ICH

DIGITAL

PROLOGIC FM AMST

USB PCM D.

DSP

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

B CA

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

VOLUMEMUTE

POWER

1, 2

1, 2 3

PRESET

P-SET

Front panel

Remote control

PRESET

P-SET

Front panel

Remote control

Front panel

Remote control

E-18

LISTENING TO AN FM BROADCAST

Copying a preset station to a different group and number

You can copy a preset station to a different group and

number. Using this function, you can arrange preset

stations in your favorite order or collect preset stations into

genres.

First turn on this unit, and then select the built-in FM tuner

as the input source.

Press the P-SET key (front panel) or the PRESET

key (remote control) to change this unit from the

frequency display mode to the preset tuning

mode.

Use the P-SET (or PRESET) key to select the

preset group, and use the / keys to select the

preset number of the station you want to copy.

Press the P-SET key (front panel) or the MEMORY

key (remote control) and keep it pressed for one

second or more.

An arrow scrolls from right to left on the display.

Use the P-SET (or PRESET) key to select the

preset group, and use the / keys to select the

preset number you want to copy the station to.

Press the P-SET key (front panel) or the MEMORY

key (remote control) and keep it pressed for one

second or more.

“MEMORY” lights up on the display for approx. 2

seconds to show that the station has been copied and

successfully stored.

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AMST

USB PCM D.

DSP

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

B CA

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

VOLUMEMUTE

POWER

1, 2, 3,

4, 5

1, 2,

3, 5

2, 4

PRESET

P-SET

Front panel

Remote control

PRESET

P-SET

Front panel

Remote control

MEMORY

P-SET

Front panel

Remote control

MEMORY

P-SET

Front panel

Remote control

PRESET

P-SET

Front panel

Remote control

E-19

ADVANCED OPERATION

English

ADVANCED

OPERATION

ADVANCED OPERATION

Adjusting the speaker balance

This procedure lets you adjust the sound output level balance between the front, center and surround speakers by using the

built-in test tone generator. Make this adjustment so that each speaker output level is about the same when heard at the

listening position. This is important for high performance of the built-in DSP (Digital Sound field Processor), the Dolby Digital

decoder and the DTS decoder.

If this unit is set to the “Virtual 3D” mode (the surround speakers are not used) in the Application Software, you can adjust the

sound output levels of the speakers in the sound field of the “Virtual 3D” mode (including two virtual surround speakers).

Refer to “Setting adjustment on the Setup panel” on page 27. This setting cannot be made by using the front panel controls or

the remote control.)

Press the TEST key on the remote control.

* You will hear a test tone (so called pink noise) from each

speaker for about two seconds in the following order.

* The speaker currently outputting the test tone is shown

on the display.

VOLUME

Remote control

VOLUME

Remote control

TEST

Remote control

TEST

Remote control

When the test tone is outputted from the left (L ch)

or right (R ch) front speaker:

Use the VOLUME keys on the remote control to

adjust the volume of each speaker.

In this step, adjust the volume balance between the left and

right front speakers.

(Adjustable range: –10 to 0)

When the test tone is outputted from the center

speaker (Cch):

Use the VOLUME keys on the remote control to

adjust the center speaker output level.

Make the sound output level of the center speaker about

the same as the left or right front speaker.

(Adjustable range: –20 to +10)

When the test tone is outputted from the left (Ls

ch) or right (Rs ch) surround speaker:

Use the VOLUME keys on the remote control to

adjust the volume of each speaker.

Make the sound output level of the surround speakers

about the same as the front speakers.

(Adjustable range: –20 to +10)

When the adjustments are finished, press the

TEST key.

The test tone stops.

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

B CA

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

VOLUMEMUTE

POWER

2, 3,

1, 5

VOLUME

Remote control

Front speaker (L)

Surround speaker (L)

Front speaker (R)

Surround speaker (R)

Center speaker

* Use the remote control for adjusting the speaker output

levels at the listening position.

E-20

ADVANCED OPERATION

Notes

● When this unit is set to the “Virtual 3D” mode:

The output order of the test tone is as follows.

When using a center speaker:

When not using a center speaker:

● Adjust the subwoofer level while listening to a suitable

source.

With the supplied Application Software, you can select the

speakers to use and not to use. Also, by designating the size of

the speakers to use, this unit can be set to an output mode

suitable for the ability of the speakers.

Setting USB channel

Typical USB audio features multi-channel modes, such as four-channel and six-channel modes, in addition to a normal two-

channel (stereo) mode. This unit is compatible with each of these modes. When a multi-channel mode is selected, you can

receive the surround sound signals of computer games compatible with the 4ch Direct Sound 3D and the multichannel

signals of DVD video on this unit via the USB connection and enjoy them in surround sounds.

Note that some operating systems and software programs are not multi-channel compatible. Yamaha websites list the names

of multi-channel compatible operating systems and software.

Notes

●

MacOS9.04, 9.1, etc. does not support this feature. Only the two-channel mode can be used. Some versions of Windows also do not

support the six and/or four-channel modes. You can refer to the following Yamaha website for details and related information.

http://www.yamaha.co.jp/audio/

● When the six channel mode is selected, recording cannot be made to the computer. To record, select the two- or four-channel mode.

Front speaker (L)

Virtual surround speaker (L)

Front speaker (R)

Virtual surround speaker (R)

Center speaker

Front speaker (L)

Virtual surround speaker (L)

Front speaker (R)

Virtual surround speaker (R)

E-21

ADVANCED OPERATION

English

ADVANCED

OPERATION

Press or repeatedly until the desired

number of channels is shown on the display.

The display changes as follows.

Hold down the PC input selector key until the

following indication appears on the display.

Although no further operation is required, wait a short time

until the computer completes the changes in the settings.

Notes

● When the number of channels is changed for the first

time, the device driver for the USB audio is installed in

the computer. Wait a short time until the computer

completes the changes in the setting.

● Do not change the USB channel setting under any

circumstance during playback or recording via the USB

connection on the computer. If changed, the computer

may freeze.

 How to set

* When playback or recording is performed on the

computer via the USB connection, terminate the

playback or recording software used on the computer.

Turn on this unit.

Press the PC input selector key repeatedly until

“USB” appears on the display.

Hold down the PC input selector key until the

current channel setting is shown (for about two

seconds).

* When the display of this unit shows “USB” in red, USB

audio is being played back, disabling this USB channel

setting function. Terminate the software used on the

computer.

Front panel

TUNER

AUX1

AUX2

Front panel

The number of

channels before the

change

The number of

channels after the

change

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL 5.ICH

DIGITAL

PROLOGIC FM AMST

USB PCM D.

DSP

2, 3,

TUNER

AUX1

AUX2

TUNER

AUX1

AUX2

E-22

ADVANCED OPERATION

Operating this unit with the Application Software

If this unit is connected to your computer via the USB

connection and the Application Software is installed in your

computer from the supplied CD-ROM, you can operate this

unit with the Application Software from your computer.

Moreover, the Application Software, once installed on your

computer, offers various settings unavailable from this unit

or the remote control. (For instructions on how to install

the Application Software, see the separate “SET UP

MANUAL”.)

This section briefly explains how to use the Application

Software, the setting screens, and the available functions.

For further details, refer to the Online Help of the

Application Software.

Notes

● The screen images shown in this section are of the basic

screens for the Windows version. The Macintosh version

slightly differs in button arrangement, etc.

● The screen design, functions, etc., are subject to change due

to version upgrades.

About the Main Panel

The Main Panel allows you to perform the following basic operations.

Tabs are shown at the bottom of the detailed-setting screen. To make detailed settings of the desired function available from

any detailed-setting screen, click on the tab for the function.

1 Display

This section shows the current status of the volume,

input selectors, sound field programs, etc. by

characters.

2 Input selector

The input selector allows you to directly change the

input source.

3 Volume control

You can adjust the volume by dragging the indicator or

by clicking the up ( ) and down ( ) arrows.

You can also alternately turn on and off the speakers

by clicking the speaker icon below.

4 Changing the panel size

You can minimize the size of the Main Panel.

5 Opening the tuner panel

Press this button to open the tuner panel. (See page

26 for details on operating the FM tuner.)

6 SETUP

Open this panel to change available settings in the

Setup panel. (See page 27 for details on the Setup

panel.)

7 DSP selector

You can directly select a DSP sound field program.

8 Detailed-setting screens

Select one of the detailed-setting screen tabs at the

bottom of the current detailed-setting screen. The new

detailed-setting screen will be displayed, where you

can make detailed settings of the function.

DSP-EDIT: For adjusting the DSP sound field

parameters (See page 23.)

SPEAKER: For adjusting the speaker output levels or

the virtual 3D effect (See page 24.)

D-RANGE: For adjusting the dynamic range

(See page 25.)

EQUALIZER: For operating the graphic equalizer

(See page 25.)

9 POWER

Each click changes the status of the main unit between

standby and power-on.

1 5

E-23

ADVANCED OPERATION

English

ADVANCED

OPERATION

Adjusting DSP sound field parameters

How to adjust parameters

1. Select the program whose parameters you wish to

adjust. (Parameter adjustment is effective for the

currently selected program only.)

2. Select the DSP-EDIT tab at the bottom of the Main

Panel. The basic parameter screen appears.

3. This screen allows you to adjust the basic parameters.

Open the “ADVANCED SETTING” panel for adjusting

the detailed parameters.

Basic parameters

Effect Level Selects the level of effect sound from the three levels.

Room Size Selects the apparent size of the listening space from the three levels.

Seat Position Selects the simulated listening position from the three positions.

Detailed parameters

The following parameters are available on the “ADVANCED SETTING” panel. Depending on the selected program and input signals,

not all of the parameters can be adjusted.

Effect Trim Makes fine adjustment of the level of the overall effect sound.

Rear Effect Trim Makes fine adjustment of the level of the rear effect sound.

Initial Delay Adjusts the apparent distance from the sound source to the walls.

Room Size Adjusts the apparent size of the listening space.

Liveness Adjusts the apparent reflectivity of the walls.

Surround Delay Adjusts the delay time of the surround sound field.

S. Initial Delay (Surround Initial Delay) Adjusts the initial delay time of the surround sound field.

(This parameter can be

adjusted only when the “Speaker Settings” of this unit has been set to two front and two

surround channels or more, and Dolby Digital- or DTS-encoded signals are inputted.)

S. Room Size (Surround Room Size) Adjusts the apparent size of the surround sound field.

Reverb Time Adjusts the duration of reverberations.

Reverb Level Adjusts the level of reverberations.

Reverb Delay Adjusts the delay time of reverberations.

Restores all parameters to their

default values.

Restores the basic parameter screen.

Select a parameter by clicking its name, and adjust the

parameter by sliding the indicator at the bottom of the panel.

You can adjust various parameters of the DSP sound field

programs.

The default parameters of the sound field programs provide

great sound, but it is also possible to fine-tune the

parameters to suit the acoustics of the room, individual

preferences, and program source. Parameter adjustment

is required for each selected sound field program.

Basic parameters

Opens the “ADVANCED

SETTING” panel.

E-24

ADVANCED OPERATION

Adjusting the speaker output levels and effect levels

When the check box “Use the surround speakers” under “Speaker Settings” in the Setup panel is checked, you can adjust the

output levels of the available speakers respectively. When the check box is not checked, this unit is in the virtual 3D mode,

allowing adjustment of the virtual 3D effects. (See page 27.)

Select the SPEAKER tab at the bottom of the Main Panel. The following screen appears.

Adjusting the output levels of the speakers

You can adjust the output levels of the speakers which are set for use under “Speaker Settings” in the Setup panel.

1 Adjusting the output levels of the main speakers

You can adjust the output levels of the left and right

main speakers.

2 Adjusting the output level and the delay time of the

center speaker

You can adjust the output level and the delay time of

the center speaker.

3 Test tone

Click on “Test tone” to output the test tone from the

respective speakers in turn. You can adjust their levels

while listening to the test tone. On the figure of the

speakers at the center of the screen, the speaker

currently outputting the test tone is indicated.

4 Adjusting the output levels of the surround

speakers

You can adjust the output levels of the left and right

surround speakers.

5 Adjusting the LFE output levels

You can adjust the output level of the LFE (Low

Frequency Effect) sounds reproduced when playing a

Dolby Digital- or DTS-encoded source. The levels can

be adjusted for Dolby Digital and DTS respectively.

Adjusting the virtual 3D effect

The surround sound effect of the virtual 3D sound field is affected by the room configuration, the position of the front

speakers and the position of the listener, resulting in sound unique to each environment. The procedure below shows you

how to adjust the effect of the virtual 3D to suit your preferences and environment.

Select the VIRTUAL tab at the bottom of the Main Panel. The following screen appears.

1 Balance adjustment

You can adjust the volume balance between the right

and left speakers.

2 Virtual surround speaker position setting

You can set the position of the virtual surround

speakers (the speakers are positioned symmetrically.)

3 HRTF (Head-related Transfer Function) adjustment

You can make an adjustment to personal

characteristics.

4 Test tone

You can output a test tone successively from the

speakers at their current positions, allowing setting and

adjustment while listening to the tone.

1 2 3 4 5

E-25

ADVANCED OPERATION

English

ADVANCED

OPERATION

Adjusting the dynamic range

You can set the dynamic range for playing a source with Dolby Digital decoded. This is especially effective for low-volume

listening. Select the D-RANGE tab at the bottom of the Main Panel. The following screen appears.

1 Dynamic range setting

Select the dynamic range for playing a source with

Dolby Digital decoded from MIN, STANDARD, and

MAX. The MAX setting provides a dynamic range of a

movie theater while MIN provides a dynamic range

suitable for late night, low-volume listening.

2 Dynamic range adjustment

This setting becomes available when you choose

STANDARD for the dynamic range. This adjusts high-

level cut scale (H-LEVELCut) and low-level boost scale

(L-LEVELBST), allowing you to freely adjust the

dynamic range between MAX and MIN.

Operating the graphic equalizer

The 7-band graphic equalizer allows you to set the frequency characteristics according to the type of the music that is played

and to compensate for the room characteristics and the speakers’ frequency characteristics. The graphic equalizer effect is

only applied to the left and right front channels.

This panel is always shown when no DSP sound field program is selected. When a DSP sound field program is selected,

selecting the EQUALIZER tab at the bottom of the Main Panel will show this panel.

1 Preset patterns

Five patterns of frequency characteristics have been

preset for different types of music, such as “ROCK” and

“POPS”. Click a button to select the effect that suits

the music type.

2 Storing and calling user’s patterns

You can store and call up to two patterns of frequency

characteristics you specify.

3 FLAT

This makes the frequency response curves flat.

4 Graphic equalizer

The 7-band equalizer allows you to set your desired

frequency response curves. By dragging the indicator

for each frequency band, you can adjust the

frequencies within the range of +6 to –6 dB.

E-26

ADVANCED OPERATION

Operating the built-in FM tuner

With the Application Software, you can operate the tuner more easily than on the front panel or the remote control, including

additional functions available only in the Application Software for example storing stations automatically and assigning names

to preset stations.

Click the button for calling the tuner panel at the right upper part of the Main Panel. The following screen appears.

1 Switching the reception mode

This button toggles the reception mode between FM

auto stereo and FM monaural.

2 Station display

The frequency of the currently received station or the

name of the preset station is shown here.

3 Manual tuning / (down/up) buttons

Press

to select higher frequencies and to select

lower frequencies.

4 TITLE

This button toggles the display mode of the preset

station list between frequencies and names.

5 CLOSE

This button closes the tuner panel.

6 ADD

This button is used for adding or changing preset

stations.

7 PRESET EDIT

This button opens the “Tuner Preset Edit” panel.

8 Preset station list

This list shows all the preset stations by their

frequencies or names.

Storing stations (Tuner Preset Edit)

Click the PRESET EDIT button in the left lower part of the tuner panel. The following screen opens and allows you to edit

the presets.

1 “Automatic store”

Click the “Start” button, and receivable stations are

stored in sequence automatically.

2 “Preset station titles”

You can assign a name consisting of up to eight

characters to each preset station. The names are

shown in the preset station list in the tuner panel.

3 “Manual store”

You can store the desired stations one by one. Click

the “Start” button, and all of the receivable stations are

searched. You can select only the desired stations and

store them onto the desired preset groups and

numbers.

4 “Close”

Click this button to close the current “Tuner Preset Edit”

panel and return to the tuner panel.

1 2 4 5

7 8

E-27

ADVANCED OPERATION

English

ADVANCED

OPERATION

Setting adjustment on the Setup panel

When you click SETUP of the Main Panel, the Setup panel appears, allowing you to perform the following settings.

USB Multi-Channel Setting (for Windows

only)

This allows you to select the number of channels for

sending playback signals via the USB connection from two,

four, and six channels. (Note that you cannot record

signals from the USB connection on the computer when six

channels are selected.)

Skin Selection

This allows you to select the skin (the design of the

background picture of the Application Software) from

several preset patterns.

Note

This feature is not available when using a Macintosh computer.

Speaker Settings

This allows you to select the speakers (center, surround

and subwoofer) to use or not to use. Also, you can select

the size (small or large) of the speakers to use. Make this

setting correctly to maximize the performance of your

speaker system.

Setting Remote Control Custom keys

This allows you to store a set of commands (input selector,

sound field program, volume setting, etc.) to each of the A,

B and C keys on the remote control. After storing, simply

pressing each key will execute the stored command.

About This Application

This gives you information about the version of this

Application Software.

Note

The screen design, functions, etc. are subject to change

due to software upgrades. For details, refer to the

Online Help of the Application Software.

Edit Names of Input Sources

You can assign a name consisting up to seven characters

to each input source. For example, if a tape deck is

connected to the AUX 1 terminals, you can change the

name, AUX 1, to TAPE. As this name change information

is sent to the main unit, the display on the main unit

changes simultaneously.

Volume Settings

 USB Mix

When USB Mix is on, even if signals received at input

terminal(s) other than the USB terminal when it is

selected, you can mix the input signals from that

selection with the signals from the computer via the

USB connection and play the mixed signals. For

example, while you are listening to music from the tape

deck connected to AUX 1, mail arrival beeps and

warning beeps are also available.

Clicking the check box to enter the check mark in the

box will turn on the USB Mix. This status allows you to

adjust the volume level of the signals from the USB

connection. (As this adjusts the volume balance

between the selected input signals and the input signals

from the USB connection, it does not affect the volume

when USB is selected by the input selector keys.)

Clicking the check box to delete the check mark will turn

off the USB Mix. In this status, the signals from the USB

connection can be played only when USB is selected by

the input selector keys.

Note

The sound field programs have no effect on USB-mixed

signals. (Sound is in normal stereo.)

 Maximum Volume Setting

When adjusting the volume in the Application Software,

you may inadvertently turn up the volume too high. To

avoid this, you can use this function to set a maximum

volume for the Application Software.

 Digital Volume Setting

This allows you to digitally turn up and down the volume

in the DSP. Take care not to turn up the volume when

the level of the digital input signal is high as it may

cause sound distortion due to digital processing. If

sound distortion occurs, turn down the volume.

Note

It may happen that the volume is fixed to “0” when digital

signals are inputted and the sound field effect is off

(THROUGH).

E-28

APPENDIX

Problem

The unit cannot be turned on

though the power switch is

pressed.

No sound.

No sound from the surround

speakers

No sound from the center speaker

No sound field effect.

No effect of Dolby Digital or DTS

though the sound field program

“NORMAL” is selected.

Cause

The power cord is not plugged in or is not

completely inserted.

This unit is in the standby mode.

Incorrect output cord connections.

The muting function of this unit is on.

Headphones are connected to the headphone

jack of this unit.

The volume is set to minimum.

The playback source is not selected by the

input selector keys.

The power of the equipment selected as the input

source is off.

The output level of the surround speakers is

set to minimum.

The DSP is off.

Under “Speaker Settings” in the SETUP panel

of the Application, the check box “Use the

surround speakers” is not checked.

The output level of the center speaker is set to

minimum.

The DSP is off, or a Hi-Fi DSP program is

selected.

Under “Speaker Settings” in the SETUP panel

of the Application, the check box “Use the

center speaker” is not checked.

The source does not contain center channel

sound signals.

The DSP is off.

The playback source is encoded with neither

Dolby Digital nor DTS.

Remedy

Firmly plug in the power cord.

Turn on this unit by pressing the power switch on the

front panel or the POWER key on the remote control.

Connect the cords properly. If the problem

persists, the cords may be defective.

Turn off the muting by pressing the MUTE key.

Disconnect the headphones from the

headphone jack to output sound from the

speakers.

Increase the volume.

Select the playback source using the input

selector keys.

When PC is selected as the input source, check

that the USB, digital or analog input is correctly

selected.

Turn on the equipment.

Increase the output level of the surround

speakers by using the test tone. (Refer to page 19

on how to adjust the speaker output levels.)

Turn on the DSP and select an appropriate

sound field program.

Check the check box “Use the surround

speakers”.

Increase the output level of the center speaker

by using the test tone. (Refer to page 19 on how

to adjust the speaker output level.)

Turn on the DSP and select a CINEMA DSP

program.

Check the check box “Use the center speaker”.

Use a source which contains center

channesound signals.

Turn on the DSP.

Use a source encoded with Dolby Digital or DTS.

Troubleshooting

Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or if the

instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service

center.

APPENDIX

E-29

APPENDIX

English

APPENDIX

Problem

When making a recording from an

audio CD to an MD, CD-R, etc., all

tracks are recorded as one track.

Program sources on an MD, CD-R,

etc. which is a copy of an audio

CD, cannot be recorded on the

computer via the USB connection.

Signals inputted to your computer

via the USB connection cannot be

recorded on the computer.

Different sounds are heard

together.

Using this unit affects TV

reception or the performance of

other equipment.

Left and right volume levels are

different.

The remote control does not work.

The remote control does not

function properly.

Cause

A DSP sound field program is selected or the

built-in graphic equalizer is used.

You cannot make a recording from a CD-R,

MD, etc. which is a copy of an audio CD, to

another CD-R, MD, etc. via the USB

connection or the digital terminal connection.

Incorrect setting of the recording device on the

computer.

Sound from the computer via the USB

connection may be mixed with sound from

other sources because the “USB Mix” setting

is set to “ON” with the Application Software.

The equipment may be too close to this unit.

The level balance is not set to center on the

“Balance” setting on the VIRTUAL panel in the

Application Software.

The batteries of the remote control are weak.

Wrong distance or angle.

Direct sunlight or strong light (of an inverter

type fluorescent lamp etc.) is striking the

remote control sensor of the main unit.

What to Do

Turn off the DSP and the graphic equalizer.

Record the signals of such an MD, CD-R, etc. on

the computer by sending the signals via an

analog connection.

Correctly set the recording device on the

computer. [Refer to “Recording on computer (via

the USB connection”) on page 13.]

Set the “USB Mix” setting to “OFF” if you do not

want to hear mixed sounds.

Move the equipment away from this unit.

Set the level balance to center.

Replace the batteries with new ones.

The remote control will function from a maximum

range of 6 meters and no more than 30 degrees

off-axis from the front panel.

Reposition the main unit.

Problem

Application does not start.

The driver software cannot be

installed successfully.

Cause

This unit and the computer is not connected

with the USB cable.

The power cord is not plugged in or is not

completely inserted.

The USB cable is not firmly connected

between this unit and the computer.

The power cord is not plugged in or is not

completely inserted.

What to Do

Connect this unit and the computer with the

USB cable.

Firmly plug in the power cord.

Disconnect the USB cable, and then connect it

firmly again.

Firmly plug in the power cord.

When installing or using the Application Software

E-30

APPENDIX

Problem

Crackling noise from time to time.

Noise increases when receiving a

stereo broadcast, or the reception

mode changes from stereo to

monaural unexpectedly.

A desired station cannot be

received by the auto tuning

method.

Stereo broadcasts are noisy and

the ST indicator flashes.

There is distortion or clear

reception cannot be obtained

even when using a good quality

FM antenna.

Preset stations cannot be

selected.

Cause

Interference from the starting motor of a

nearby car.

Interference from the thermostats of a nearby

electric appliance.

Because of the characteristics of FM

broadcasts, this is limited to cases where the

transmitter is far away or the antenna signal is

weak.

Because of the characteristics of FM

broadcasts, this is limited to cases where the

transmitter is far away or the antenna signal is

weak.

Weak antenna signal.

Not tuned correctly.

There is multipath interference.

The preset memory has been erased.

What to Do

Position the FM antenna as high and as far

away from nearby roads as possible.

Use a coaxial cable for connecting the antenna.

Install a noise canceller on such an appliance.

Check the antenna connections.

Install a multi-element type FM antenna if

possible.

Tune in to the station manually.

Install an antenna suitable for the electric field

strength of your area.

Retune.

Change the position of the antenna.

Store the stations again.

When using the built-in FM tuner

Depending on some computer hardware or operating systems, all functions of this unit cannot be used.You can refer to

the following Yamaha website for details and related information.

http://www.yamaha.co.jp/audio/

Memory back-up

The memory back-up circuit prevents the setting of the input selector, the sound field program, the preset memory of

the tuner from being lost even if the AC power cord is disconnected from the AC outlet or the power is cut due to a

temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. In that

case, you must make the necessary settings, and store the FM stations in memory again.

E-31

APPENDIX

English

APPENDIX

Specifications

Minimum RMS Output Power per Channel

12W  5 (20 Hz–20 kHz, 4Ω, 1% THD)

Maximum Power 14W  5 (1 kHz, 4Ω, 10% THD)

Input Sensitivity/Input Impedance

PC IN, AUX1 IN, AUX2 IN (ANALOG) 150 mV/35 kΩ

Maximum Input Signal

PC, AUX1, AUX2 2.1V or more (1 kHz)

Output Level/Output Impedance

REC OUT 150 mV/2.0 kΩ

SUBWOOFER OUTPUT 1.0V/1.7 kΩ (50 Hz)

Headphone Jack Output Level/Output Impedance

ANALOG PC IN, etc. 320 mV/61Ω (1 kHz, 150 mV)

Frequency Response

USB, DIGITAL IN (PC, AUX1) to SP Output

20 Hz–20 kHz (2.0 dB)

Total Harmonic Distortion (1 kHz, 20 kLPF)

USB, DIGITAL IN (PC, AUX1) to SP Output

0.2% or less (5V/4Ω)

Signal-to-Noise Ratio

USB to SP Output 85 dB or more

PC IN, AUX1 IN (DIGITAL) to SP Output

85 dB or more

Residual Noise (IHF-A Network)

–66 dB or less (SP Output, L/R)

Tuning Range

[U.S.A. and Canada models] 87.5 to 107.9 MHz

[Europe, U.K. and Australia models]

87.5 to 108.0 MHz

Usable Sensitivity

MONO 6 dBµ

Power Supply

[U.S.A. and Canada models] AC 120V, 60 Hz

[Europe and U.K. models] AC 230V, 50 Hz

[Australia model] AC 240V, 50 Hz

Power Consumption 90W

(In the standby mode: 5W or less)

Dimensions (W  H  D) 120  294  355 mm

(4-3/4”  11-9/16”  14”)

Weight 5.5 kg (12 lbs. 2 oz.)

Accessories CD-ROM (Windows/Macintosh-hybrid)

USB cable

Remote control

Battery2

Indoor FM antenna

Specifications are subject to change without notice.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia V688970

PERSONAL RECEIVER

RP-U200

SET UP MANUAL

MANUEL DE CONFIGURATION

U C A

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FM AM ST

USB PCM D.

DSP

POWER

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

VOLUMEMUTE

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

The owner’s manual for this model consists of two volumes, “SET UP MANUAL” and

“OPERATION MANUAL”.

Le manuel d'utilisation pour ce modèle se compose de deux volumes, le “MANUEL DE

CONFIGURATION” et le “MANUEL D’UTILISATION”.

* This manual uses terms utilized by the English operating system as shown on the computer monitor. If the operating

system you are using is in another language, please replace the English terms with the terms used in your computer’s

operating system.

* Ce manuel utilise des termes employés par les systèmes d’exploitation en langue anglaise tels qu’ils apparaîssent sur le

moniteur d’un ordinateur. Si votre système d’exploitation utilise une autre langue, veuillez remplacer la terminologie

anglaise par celle qu’il utilise.

E-1

CONNECTIONS

Terminals and their functions ........... 3

Connecting your computer................ 4

Connecting audio equipment ............ 5

Connecting speakers ......................... 6

Connecting an FM antenna ................ 9

Plugging in this unit ........................... 9

INSTALLING USB DRIVER AND

APPLICATION SOFTWARE

Preparations before installation...... 10

System requirements....................... 10

Installing the software...................... 11

Microsoft Windows 98/98SE

or Windows Me ............................................... 11

Microsoft Windows 2000 Professional ......... 14

Macintosh computer ...................................... 17

CONNECTIONS

INSTALLING USB DRIVER AND

APPLICATION SOFTWARE

English

GETTING STARTED

Unpacking........................................... 2

Battery installation ............................. 2

Battery replacement........................... 2

Remote control operation range ....... 2

GETTING STARTED

CONTENTS

E-2

● Batteries (AA, R6, UM-3

type)

● USB cable

(U.K., Europe and Australia

models)

GETTING STARTED

Battery installation

Since the remote control will be used for many of this unit’s

control operations, you should begin by installing the

supplied batteries.

Turn the remote control over and remove the battery

compartment cover by sliding it in the direction of

the arrow.

Insert the batteries (AA, R6, UM-3 type) according to

the polarity markings on the inside of the battery

compartment.

Close the battery compartment cover.

Battery replacement

If you notice that the remote control must be used closer to

the main unit, the batteries are weak. Replace both

batteries with new ones.

Notes

● Use AA, R6, UM-3 batteries.

● Be sure the polarities are correct. (See the illustration

inside the battery compartment.)

● Remove the batteries if the remote control is not to be used

for an extended period of time.

● If the batteries leak, dispose of them immediately. Avoid

touching the leaked material and avoid contact with

clothing, etc. Clean the battery compartment thoroughly

before installing new batteries.

POWER

AUX1

AUX2

TUNER

JAZZ CHURCHHALL

VOLUMEMUTE

MOVIE LIVE

PRESET MANUALMEMORY

GAME

TEST

OFF

/DTS

SURROUND

Remote control operation range

Notes

● The area between the remote control and the main unit

must be clear of large obstacles.

● Do not expose the remote control sensor to strong lighting,

in particular, an inverter type fluorescent lamp; otherwise,

the remote control may not work properly. If necessary,

position the main unit away from direct lighting.

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FMAM ST

USB PCM D.

DSP

30°

Remote control

sensor

Unpacking

After unpacking, check that the following items are

supplied.

● Remote control

● Indoor FM antenna

(U.S.A. and Canada

models)

● CD-ROM

The CD-ROM contains

the Application Software

and online help for

controlling this unit from

your computer.

Within

approximately

6 m (19.7 feet)

E-3

CONNECTIONS

Never

plug in this unit and other equipment until

all connections are completed.

Make connections between this unit and other

components by following the procedure below.

After all connections are finished, check that the

connection cables are correctly connected.

After all connections are completed, plug in this unit and

other equipment.

Note

Also, refer to the owner’s manual for other equipment in the

system.

CONNECTIONS

Terminals and their functions

+–

R L

ANALOG

PC IN

FM ANT

Ω UNBAL.

AUX 1

AUX 2

REC

OUT

OUTPUT

SUB

WOOFER

DIGITAL

USB

COAX

OPT

AUX 1

OPT IN

OPT

OUT

SPEAKERS

4Ω MIN.

SPEAKER

REAR

+–

FRONT

CENTER

ANTENNA

1 FM antenna connector

This connector is used to connect an FM antenna.

2 SUBWOOFER OUTPUT

This connector can be connected to an optional subwoofer,

such as the Yamaha YST-SW45, for enhanced bass

performance.

3 SPEAKERS outputs

Up to five speakers, such as the Yamaha NS-U40P

speaker system can be connected to the FRONT L, R,

CENTER, REAR L and R terminals. Use speakers whose

impedance is 4Ω or more.

4 ANALOG inputs

These connectors are used to connect to the analog

outputs of a PC sound card, CD player, MD recorder, tape

deck, etc.

5 REC OUT

These connectors are used to connect to the analog inputs

of an MD recorder or tape deck.

6 PC inputs & output (DIGITAL)

USB: If your computer has a USB port, connect it to this

unit, using the supplied USB cable, for remote control of

this unit from your computer.

PC COAX IN/OPT IN: These coaxial and optical

connectors are used to connect to the digital outputs of a

PC sound card, DVD-Video decoder board, etc.

7 Optical input & output (DIGITAL)

AUX 1 OPT IN: This connector is used to connect to an

optical output of a CD player, MD recorder, etc.

OPT OUT: This connector is used to connect to an optical

input of an MD recorder, a DAT deck, etc.

Use commercially available connection cables (except the supplied USB cable).

The color of this unit’s inputs/outputs and pin-plug connection cables to be used for connecting to them are as follows:

White Analog audio signals for the left channel (stereo)

Red Analog audio signals for the right channel (stereo)

Black Analog audio signals (monaural)

Digital audio signals (coaxial)

(U.S.A. model)

E-4

CONNECTIONS

Connecting to the USB port (1)

If your computer has a USB port, connect it to this unit’s

USB terminal using the supplied USB cable, as shown

below.

A single USB connection is all that’s required to listen to

audio from your computer on this unit, feed audio from an

external source connected to this unit to your computer,

and control this unit remotely from your computer, using

the supplied Application Software.

If your computer doesn’t have a USB port, you can still

connect it to this unit using the analog or digital input, but in

this case you cannot use this unit’s Application Software.

Note

Connect the USB cable when installing the USB driver

software on your computer. Refer to the section

“INSTALLING USB DRIVER AND APPLICATION

SOFTWARE”.

Connecting to analog inputs (2)

Connect the analog audio outputs on your computer or a

PC sound card to this unit’s ANALOG PC IN.

Use a commercially available pin-plug cable for connection,

and be careful not to mix up the left and right connections.

Connecting your computer

Audio from your computer can be fed to this unit using any of the following connectors: USB, DIGITAL PC COAX IN, DIGITAL

PC OPT IN, or ANALOG PC IN. If you use all of these connectors for connection, you can select the connector(s) to use on

this unit’s front panel or the remote control.

+–

R L

ANALOG

AUX 1

AUX 2

REC

OUT

OUTPUT

SUB

WOOFER

DIGITAL

USB

COAX

OPT

AUX 1

OPT IN

OPT

OUT

SPEAKERS

4Ω MIN.

SPEAKER

REAR

+–

FRONT

CENTER

ANTENNA

R L

PC IN

FM ANT

75Ω UNBAL.

LINE OUT

USB

DIGITAL

OUT

DIGITAL

OUT

(coaxial)

(optical)

Connecting to digital inputs (3)

To play DVD-Video discs encoded with Dolby Digital or

DTS, your computer must have a DVD-ROM drive and

DVD-Video decoder board, which should be connected to

this unit via the DIGITAL PC COAX IN or DIGITAL PC OPT

IN.

Use a commercially available pin-plug cable for connecting

to the DIGITAL PC COAX IN, and use a commercially

available optical fiber cable for connecting to the DIGITAL

PC OPT IN.

Note

The DIGITAL PC OPT IN has priority over the DIGITAL PC

COAX IN, so if you connect to both inputs, the signal received at

the DIGITAL PC OPT IN is used.

Protective Caps

When connecting to an optical connector, remove its

protective cap first. When an optical connector is not being

used, replace its cap to prevent dust entering the connector.

: Indicates the direction of signals.

(U.S.A. model)

E-5

CONNECTIONS

Connecting audio equipment

The following illustrations show how to connect a CD player, MD recorder, etc. using both analog and digital connections.

However, it’s not necessary to make both connections.

R L

ANALOG

AUX 1

AUX 2

REC

OUT

OUTPUT

SUB

WOOFER

DIGITAL

USB

SPEAKERS

+–

FRONT

ANTENNA

R L

PC IN

FM ANT

75Ω UNBAL.

LINE OUT

LINE IN

(REC)

LINE OUT

(PLAY)

+–

DIGITAL

USB

COAX

OPT

AUX 1

OPT IN

OPT

OUT

SPEAKERS

4Ω MIN.

SPEAKER

REAR

+–

FRONT

CENTER

DIGITAL OUT

DIGITAL IN

(optical)

CD player

MD recorder

CD player

Tape deck

or MD recorder

Audio connections

● Be careful not to mix up the left and right connections.

● If you wish to record analog sound signals inputted to

this unit, connect the analog inputs of a tape deck or

MD recorder to this unit’s REC OUT.

Digital connections

If you wish to record digital sound signals inputted to this

unit, connect the optical digital input of an MD recorder or a

DAT deck to this unit’s DIGITAL OPT OUT.

Notes

● When playing an ordinary CD on this unit following

playback of a CD or an LD encoded with DTS, some

operations, such as resetting the input selector keys, may be

required.

● If some data processing (e.g. volume level changes) is applied

to DTS-encoded signals on the CD, DVD or LD player, this

unit will not recognize the signals as DTS-encoded signals.

Because of this, this unit cannot reproduce a DTS-encoded

source played on such a player even if it is connected to this

unit with a digital connection.

● When an error occurs in the player’s digital output data

during playback of an LD or CD encoded with DTS,

playback may be disrupted. If this occurs, stop playback and

repower the player.

● When digital sound signals from the computer are played,

errors in WAV signals, etc. may occur resulting in noise or a

playback failure.

Notes

● Connecting a turntable

A turntable cannot be connected to this unit directly. Use a

commercially available phono preamp to connect a turntable to

this unit, or connect a turntable incorporated with a phono

equalizer amplifier.

● The REC OUT and DIGITAL OPT OUT can be used at the

same time since they output signals independently.

(U.S.A. model)

E-6

CONNECTIONS

+–

R L

ANALOG

AUX 1

AUX 2

REC

OUT

OUTPUT

SUB

WOOFER

DIGITAL

USB

COAX

OPT

AUX 1

OPT IN

OPT

OUT

SPEAKERS

4Ω MIN.

SPEAKER

REAR

+–

FRONT

CENTER

ANTENNA

R L

PC IN

FM ANT

75Ω UNBAL.

Front speaker (L)

Front speaker (R)

Connecting speakers

To reproduce multi-channel surround sounds with this unit,

connect five speakers (Yamaha NS-U40P, etc.) to this unit

as follows: a pair of front speakers to the FRONT L and R

terminals, a center speaker to the CENTER terminal, and a

pair of surround speakers to the REAR L and R terminals.

When using only one pair of speakers, connect one

speaker to the FRONT L terminal, and the other to the

FRONT R terminal.

* When the supplied Application Software is installed on

the computer connected to this unit, the Application

enables you to make “Speaker Settings”. In the settings,

you can select the speakers to use and not to use, and

also set the sizes of the speakers to use. Refer to page

27 of the separate “OPERATION MANUAL” for details.

Notes

● Use speakers which do not have a built-in amplifier.

● Use speakers whose impedance is 4Ω or more.

● Connect the left speaker to the left speaker connector on

this unit and the right speaker to the right speaker

connector.

● Make sure that the + and – polarity markings of the

speaker cables are observed and set correctly. If these

cables are reversed, the sound will be unnatural and lack

bass.

Center speaker

Surround speaker (L) Surround speaker (R)

(U.S.A. model)

E-7

CONNECTIONS

R L

ANALOG

AUX 1

AUX 2

REC

OUT

OUTPUT

SUB

WOOFER

DIGITAL

USB

SPEAKERS

+–

FRONT

ANTENNA

R L

PC IN

FM ANT

75Ω UNBAL.

SUPERWOOFER SYSTEM YST-SW45

HIGH CUTSTANDBY/ON

150Hz50Hz

VOLUME

100

LINE IN

Subwoofer

Adding a subwoofer

It is recommended to connect a subwoofer to this unit to

enhance the bass performance of your system and

reproduce surround sounds of Dolby Digital, DTS and

CINEMA DSP effectively.

Notes

● The SUBWOOFER OUTPUT is a line-level output. Use a

subwoofer which has its own built-in power amplifier,

such as the Yamaha YST-SW45.

● If no sound is reprodced from the subwoofer, check the

“Speaker Settings” in the Application Software. Refer to

page 27 of the separate “OPERATION MANUAL” for

details.

10 mm

➁

➂

➀

Speaker Cables

Strip 10 mm of insulation off the end of each speaker

cable, and then twist the bare wires to prevent lose

strands, which can cause short circuits.

How to connect:

1 Press and hold the speaker connector levers.

2 Insert the bare ends of the speaker cables into the

terminal holes.

3 Then release the levers.

* Try pulling gently on each cable to make sure that it is

secure.

(U.S.A. model)

E-8

CONNECTIONS

Surround speaker (left)

Front speakers:

On both sides of and at approximately the same height as

your computer monitor.

The distances from each speaker to the listening position

must be the same.

Surround speakers:

Behind your listening position or on both sides of the

listening room. According as the condition of your listening

room, place the surround speakers on the floor or the shelf,

or mount them on the wall.

Center speaker:

Precisely between the front speakers.

* The center speaker can be mounted on the monitor if it

is a magnetically shielded type.

Subwoofer:

On the floor. Place the subwoofer on the position where

you can get the optimum bass performance from the

listening position.

Note

Use magnetically-shielded speakers and subwoofer. If the

monitor picture is disturbed even by using the magnetically-

shielded speakers, set the speakers apart from the monitor.

Setting up the speakers

The role of the respective speakers

In a 5.1-channel surround system, the front speakers are

used for reproducing main channel sound (normal stereo

sound) and effect sound. The surround speakers are used

for surround and effect sounds, and the center speaker is

for center channel sound (dialog, etc.). (The center speaker

can be omitted if you prefer, however, the best result is

obtained with a full five speaker system.)

The subwoofer is used for reproducing low frequency

sounds from the front, center and surround channels. The

subwoofer also reproduces sounds of the subwoofer

channel when a DTS or Dolby Digital encoded source is

played.

Recommended speaker placement

Before making connections, place all speakers in their

respective positions. The positioning of the speakers is

important because it controls the overall sound quality of

this system.

Place the speakers depending on your listening position by

following the instructions below.

A set up example

Surround speaker (right)

Front speaker (right)

Front speaker (left)

Center speaker

Subwoofer

This unit

E-9

CONNECTIONS

R L

ANALOG

AUX 1

AUX 2

REC

OUT

OUTPUT

SUB

WOOFER

DIGITAL

USB

SPEAKERS

+—

FRONT

ANTENNA

R L

PC IN

FM ANT

75Ω UNBAL.

AC outlet

Connecting an FM antenna

Connect an FM antenna to the FM ANT terminal of this unit by following the figure and procedures below.

(U.S.A. model)

Plugging in this unit

It is recommended to use an outdoor FM antenna for good

reception.

Depending the area, good reception may not be obtained

because it is far from FM radio stations or obstructed by tall

buildings, mountains, and so on. Select a type of antenna

suitable for your area.

Also, to minimize the effects of automobile ignition noise,

locate the antenna as far away from heavy traffic as

possible.

● Use the supplied indoor FM antenna only in areas with

exceptionally good reception.

Insert the antenna connector securely.

* Set the indoor FM antenna as far away from the

computer and the monitor as possible, and set it to a

position where the best reception is obtained.

● For connecting an outdoor FM antenna

Use a 75Ω coaxial cable for connecting the antenna.

If the antenna is located far from this unit, the use of

5C2V cable is recommended to handle the weak radio

signal.

* If you connect an outdoor FM antenna to this unit, do

not connect the indoor FM antenna to this unit.

After completing all connections, plug the AC power

cord into a household AC outlet.

Note

Unplug the AC power cord from the AC outlet if this unit is

not to be used for a long period of time.

Indoor FM antenna (supplied)

Outdoor FM antenna

F-type plug adaptor

75Ω coaxial cable

(U.S.A. model)

E-10

INSTALLING USB DRIVER AND APPLICATION SOFTWARE

Microsoft Windows 98/98SE, Windows Me or

Windows 2000 Professional

Operating System

Microsoft Windows 98/98SE, Windows Me or Windows

2000 Professional

Computer

A computer with a USB port as a standard equipment and

preinstalled with the above OS.

Windows is a registered trademark of Microsoft Corporation in

the United States and/or other countries.

When connecting this unit and your computer with the USB

cable and controlling this unit from the computer, you must

install the following software on your computer.

◆ USB driver software: Necessary for this unit to

communicate with your computer .......... Use the

software originally supplied with the OS (Operating

System) running on your computer

◆ Application Software: Used to control this unit from a

computer .......... Download from the supplied CD-ROM

◆ Online help : Instructions for using the Application

......... Access from the supplied CD-ROM

This section explains how to install the software. The

installation method differs from the OS running on your

computer.

Refer to the instructions suitable for your OS below.

Preparations before installation

● Make sure that the USB cable is not connected to

this unit and that your computer is not activated.

● Make sure that your computer meets the system

requirements listed below.

If your computer does not meet the system

requirements, you can use the computer as an input

source by connecting it to the analog or digital input(s)

of this unit. In that case, however, the supplied

Application Software cannot be used.

● You may be requested to insert your OS’s CD-ROM

during the installation, so please have it ready before

commencing.

● The installing method may differ from the instructions

below depending on the operating environment of your

computer. In such a case, follow the instructions shown

on the monitor. If you still have any question, inquire at

the manufacturer of your computer or a computer

dealer.

System requirements

Your computer must meet the following system requirements to use the supplied Application Software.

INSTALLING USB DRIVER AND APPLICATION SOFTWARE

Macintosh

Operating System

Mac OS 9.04, 9.1 or greater (except for the OS 9.04

preinstalled on Macintosh computers put on the market in

June of 2000 or before)

Computer

Macintosh computer preinstalled with the above OS and

equipped with a USB port as a standard equipment

Macintosh is a trademark of Apple Computer, Inc., registered in

the U.S. and other countries.

E-11

English

INSTALLING USB DRIVER AND APPLICATION SOFTWARE

INSTALLING USB DRIVER AND

APPLICATION SOFTWARE

Installing the software

Microsoft Windows 98/98SE or Windows Me

䡵 Installing and checking the USB driver

Turn on your computer and, if it’s not running

already, start Windows 98/98SE or Windows Me.

Plug the AC power cord of this unit into the AC

outlet.

This unit can be on or in standby mode when installing the

driver.

Connect this unit to a USB port on the computer

using the supplied USB cable.

Windows automatically detects this unit and installs the

necessary driver software. Make operations as indicated in

the dialog box. You may be requested to insert your

Windows OS CD-ROM.

* The installation may take a longer time depending on

the system environment. After the installation dialog

box disappears, wait several minutes.

Check that the USB driver has been installed successfully

by following the procedure below.

Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

The Control Panel window appears.

Double-click the “System” icon.

The System Properties window appears.

Click the “Device Manager” tab.

The Device Manager window appears.

Click the “View devices by type” option button.

Click the “+” symbol next to “Sound, video and

game controllers,” and make sure that “USB Audio

Device” appears in the list, as shown.

* The screen image is for Windows 98SE.

* When using Windows Me, “?” may be shown at the

head of “USB Copmposite Device” in green. This

means the USB driver has been installed with the

Generic ID supplied with the operating system. (This is

not an error message.)

Click the “+” symbol next to “Human Interface

Devices”, and make sure that “HID-compliant

consumer control device” and “USB Human

Interface Device” appear in the list, as shown.

* The screen image is for Windows 98SE.

Click the “+” symbol next to “Universal Serial

Bus controllers” and make sure that “USB

Composite Device” appears in the list, as

shown.

* The screen image is for Windows 98SE.

Notes

● The device list on your computer may differ to that shown

here.

● If “!” or “?” is shown at the head of the device name, check

the followings:

* The USB cable is firmly connected.

* The AC power cord of this unit is plugged into an AC

outlet.

● If the driver has not been successfully installed, disconnect

the USB cable and connect it again. Then try to install the

driver again. If installation still fails, restart Windows and try

again.

E-12

INSTALLING USB DRIVER AND APPLICATION SOFTWARE

Make the following settings on your computer after the installation of the driver is finished.

Setting of Audio and Audio CD

[Windows 98/98SE only]

* Terminate all the activated applications.

* When using Windows 98SE, restart Windows, first.

Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

Double-click the “Multimedia” icon.

Click the “Audio” tab and select “USB Audio

Device” at “Preferred device” of “Playback”.

* Usually, this setting is automatically made.

* If “USB Audio Device” does not appear, restart

Windows.

Click the “CD Music” tab and select the CD-ROM

drive for playing audio CDs.

Click the check box of “Enable digital CD audio for

this CD-ROM device” to enter the check mark.

* It may happen that the check box cannot be clicked

because some CD-ROM drives cannot be used for

playing audio CDs.

Click “OK” and close the “Multimedia” setting

panel.

Restart Windows.

Note

When using two or more drives, you must make the above setting

for each drive.

Checking the Audio setting

[Windows Me only]

Click the Windows Me “Start” button and select

“Settings”, and then “Control Panel”.

Double-click the “Sounds and Multimedia” icon.

Click the “Audio” tab and select “USB Audio

Device” at “Preferred device” of “Sound

Playback”.

* Usually, this setting is automatically made.

* If “USB Audio Device” does not appear, restart

Windows.

Checking sound output and adjusting volume

[Windows 98/98SE and Windows Me]

Make the following operations on the front panel of

this unit.

a)Press the power switch to turn on this unit.

(Some messages are shown on the display.)

b)Press the PC input selector key repeatedly to

select USB as the input source.

c) Use the volume control to adjust the volume.

(Set the control to about “30”.)

Adjust the volume on the computer as follows.

a) Double-click the speaker icon on the task tray,

or select “Start”, “Programs”, “Accessories”,

“Entertainment” in this order and click “Volume

Control”.

(The volume adjustment window appears.)

b)Adjust the volume by dragging the “Volume”

slider. Set the slider between the center and

max. positions.

* Do not enter the check mark in the “Mute” check

box. If entered, sound output will stop.

Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

Double-click the “Sounds” (or “Sounds and

Multimedia”) icon.

Click the “Sounds” tab.

Check that the sound is output normally by

outputting “Default sound”, etc. from “Events” (or

“Sound Events”).

* If no sound is heard, restart Windows and check again.

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FMAM ST

USB PCM D.

DSP

Display

Volume control

Power switch

E-13

English

INSTALLING USB DRIVER AND APPLICATION SOFTWARE

INSTALLING USB DRIVER AND

APPLICATION SOFTWARE

Next, install the Application Software and Online Help

from the supplied CD-ROM.

䡵 Installing the Application Software

* Terminate all the activated applications (including virus

checkers) on the computer first.

Insert the CD-ROM into the CD-ROM or DVD-ROM

drive.

If the Windows Autorun feature is turned on, the

installation start-up screen appears automatically.

Continue with the installation as prompted.

If the Windows Autorun feature is not turned on

Display the contents of the CD-ROM by using “My

Computer” etc., and double-click on “Readme.txt.”. The

installation method is described in this file.

䡵 Using the Application Software and

Online Help

This section explains how to start the Application Software

and view the online help.

Click the Windows “Start” button and select

“Programs”, “YAMAHA RP-U200”, “RP-U200” in

this order.

The Application Software starts.

To view the online help, click the Windows “Start”

button and select “Programs”, “YAMAHA RP-

U200”, “Help” in this order.

The online help, which explains how to use the Application

Software, starts.

Note

Never disconnect the USB cable while starting up the

Application Software. If disconnected, the computer may

freeze.

䡵 Uninstalling the Application Software

This section explains how to uninstall the Application

Software.

Terminate the Application Software and online

help.

Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

The Control Panel window appears.

Double-click the “Add/Remove Programs” icon.

The “Add/Remove Programs Properties” window appears.

Select “YAMAHA RP-U200 Application” in the

software list.

“YAMAHA RP-U200 Application” is highlighted.

Click the “Add/Remove Programs” button and

continue as prompted.

E-14

INSTALLING USB DRIVER AND APPLICATION SOFTWARE

Microsoft Windows 2000 Professional

䡵 Installing and checking the USB driver

Turn on your computer and, if it’s not running

already, start Windows 2000 Professional, and log

in with Administrator.

Plug the AC power cord of this unit into the AC

outlet.

This unit can be on or in the standby mode when installing

the driver.

Connect this unit to a USB port on the computer

using the supplied USB cable.

Windows automatically detects this unit and installs the

necessary driver software.

* The installation may take a longer time depending on

the system environment. After the dialog box for

installation disappears, wait several minutes.

Check that the USB driver has been installed successfully

by following the procedure below.

Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

The Control Panel window appears.

Double-click the “System” icon.

The System Properties window appears.

Select the “Hardware” tab, and click the “Device

Manager”.

The Device Manager window appears.

Select the “View” tab, and click the “Devices by

type” option button.

Click the “+” symbol next to “Sound, video and

game controllers,” and make sure that “USB Audio

Device” appears in the list, as shown.

Click the “+” symbol next to “Human Interface

Devices”, and make sure that “HID-compliant

consumer control device” and “USB Human

Interface Device” appear in the list, as shown.

Click the “+” symbol next to “Universal Serial

Bus controllers” and make sure that “USB

Composite Device” appears in the list, as

shown.

Notes

● The device list on your computer may differ to that shown

here.

● If “!” or “?” is shown at the head of the device name, check

the followings:

* The USB cable is firmly connected.

* The AC power cord of this unit is plugged into an AC

outlet.

● If the driver has not been successfully installed, disconnect

the USB cable and connect it again. Then try to install the

driver again. If installation still fails, restart Windows and try

again.

E-15

English

INSTALLING USB DRIVER AND APPLICATION SOFTWARE

INSTALLING USB DRIVER AND

APPLICATION SOFTWARE

Make the following settings on your computer after the installation of the driver is finished.

Setting of Audio and Audio CD

Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

Double-click the “Sounds and Multimedia” icon.

Click the “Audio” tab and select “USB Audio

Device” at “Preferred device” of “Sound

Playback”.

* Usually, this setting is automatically made.

Click the “Hardware” tab and double-click the item

of the DVD or CD-ROM to be used in the “Devices”.

Click the “Properties” tab, and click the check box

of “Enable digital CD audio for this CD-ROM

device” to enter the check mark.

* It may happen that the check box cannot be clicked

because some CD-ROM drives cannot be used for

playing audio CDs.

Restart Windows, and log in with Administrator.

Note

When using two or more drives, you must make the above setting

for each drive.

Checking sound output and adjusting volume

Make the following operations on the front panel of

this unit.

a)Press the power switch to turn on this unit.

(Some messages are shown on the display.)

b)Press the PC input selector key repeatedly to

select USB as the input source.

c)Use the volume control to adjust the volume.

(Set the control to about “30”.)

Adjust the volume on the computer as follows.

a)Double-click the speaker icon on the task tray,

or select “Start”, “Programs”, “Accessories”,

“Entertainment” in this order and click “Volume

Control”.

(The volume adjustment window appears.)

b)Adjust the volume by dragging the “Volume”

slider. Set the slider between the center and

max. position.

* Do not enter the check mark in the “Mute” check

box. If entered, sound output will stop.

Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

Double-click the “Sounds and Multimedia” icon.

Click the “Sounds” tab.

Check that the sound is output normally by

outputting “Default Beep”, etc. from “Sound

Events”.

* If no sound is heard, restart Windows and check again.

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FMAM ST

USB PCM D.

DSP

Display

Volume control

Power switch

E-16

INSTALLING USB DRIVER AND APPLICATION SOFTWARE

Next, install the Application Software and Online Help

from the supplied CD-ROM.

䡵 Installing the Application Software

Insert the CD-ROM into the CD-ROM or DVD-ROM

drive.

If the Windows Autorun feature is turned on, the

installation start-up screen appears automatically.

Continue with the installation as prompted.

If the Windows Autorun feature is not turned on

Display the contents of the CD-ROM by using “My

Computer” etc., and double-click on “Readme.txt.”. The

installation method is described in this file.

䡵 Using the Application Software and

Online Help

This section explains how to start the Application Software

and view the online help.

Click the Windows “Start” button and select

“Programs”, “YAMAHA RP-U200”, “RP-U200” in

this order.

The Application Software starts.

To view the online help, click the Windows “Start”

button and select “Programs”, “YAMAHA RP-

U200”, “Help” in this order.

The online help, which explains how to use the Application

Software, starts.

Note

Never disconnect the USB cable while starting up the

Application Software. If disconnected, the computer may

freeze.

䡵 Uninstalling the Application Software

This section explains how to uninstall the Application

Software.

Terminate the Application Software and online

help.

Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

The Control Panel window appears.

Double-click the “Add/Remove Programs” icon.

The “Add/Remove Programs” window appears.

Select “YAMAHA RP-U200 Application” in the

software list.

“YAMAHA RP-U200 Application” is highlighted.

Click the “Change/Remove” button and continue

as prompted.

E-17

English

INSTALLING USB DRIVER AND APPLICATION SOFTWARE

INSTALLING USB DRIVER AND

APPLICATION SOFTWARE

Macintosh computer

䡵 Connections and setup

Plug the AC power cord of this unit into the AC

outlet.

Start the Macintosh.

Connect this unit to a USB port on the computer

using the supplied USB cable.

The driver software for USB audio is automatically

installed.

Press the power switch of this unit to turn on this

unit.

Some messages are shown on the display.

Checking sound output and adjusting volume

Make the following operations on the front panel of

this unit.

a)Press the PC input selector key repeatedly to

select USB as the input source.

b)Use the volume control to adjust the volume.

(Set the control to about “30”.)

Check that the sound is output normally by

outputting “Alert Sounds”, etc. from “Sound” on

the “Control Panels” on the Macintosh.

Adjust the volume by dragging the “Sound” tab on

the “Control Panels”. Set the tab between the

center and max. position.

Notes

● The sound output destination cannot be changed from

“Choose a device for sound output” on the “Control

Panels”. When using the internal speaker of the

Macintosh as the sound output destination, disconnect the

USB cable connecting this unit and the Macintosh.

● When using headphones with this unit connected to the

USB port on the Macintosh, use the headphone jack on

this unit, not the jack on the Macintosh.

● Since the Macintosh issues a start-up sound at power-on

before the sound signal via the USB connection is

activated, the start-up sound cannot be issued via the USB

connection. To play the start-up sound via this unit, you

need a separate analog connection between this unit and

the Macintosh. (When USB MIX is set to “ON” from the

Setup Panel of the Application Software, you can mix the

start-up sound via the analog connection with the same

sound via the USB connection without making any change

in the input selector settings.)

AUX1

AUX2

TUNER

DSP P-SET

VOL

VIRTUAL

5.I

DIGITAL

PROLOGIC FMAM ST

USB PCM D.

DSP

Display

Volume control

Power switch

E-18

INSTALLING USB DRIVER AND APPLICATION SOFTWARE

Next, install the Application Software and Online Help

from the supplied CD-ROM.

䡵 Installing the Application Software

Insert the CD-ROM into the CD-ROM or DVD-ROM

drive.

The CD-ROM includes the simple installer “RP-U200

Installer” and the installation data folder.

Open the folder “English”, and double-click the

simple installer “RP

DP Installer” to start it.

Select the model name of this unit and the destination of

the installation.

The Application Software and Online Help are installed on

the hard disk.

* Files installed by the simple installer

The simple installer “RP

DP Installer” copies the

“RP

DP Application” folder in the installation data

folder to a specified location. It additionally copies the

“RP

DP Help” folder into the “Help” folder in the

“System Folder” on the startup disk.

* To install the Application Software without using the

simple installer, follow the instructions below.

Installing the Application Software without using

the simple installer “

DP Installer”:

Copy the “RP-U200 Application” folder in the

installation data folder to any hard disk.

Copy the “RP-U200 Help” folder in the installation

data folder to the “Help” folder in the “System

Folder” on the startup disk.

You can refer to this Online Help file with Mac Help.

䡵 How to use the Application Software and

Online Help

All operating instructions for the Application Software is

available from the Online Help. To refer to the instructions,

select the Online Help from the menu displayed upon

activation of the Application Software.

Relationship between operation on this unit and the

Application Software

When an operation button or the volume control on this unit

is operated with the Application Software activated, the

display screen of the Application Software automatically

changes to reflect the changes made on the unit. When

this unit is operated as above while the display shows the

screens of the Application Software data and another

program, the display of the other program (for example, the

playback display of QuickTime) may be partially disturbed

as the screen of the Application Software responds to the

operation on this unit. To avoid this, operate this unit

without activating the Application Software.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia V689000

Transcripción de documentos

UCA PERSONAL RECEIVER RP-U200 PC AUX1 AUX2 TUNER POWER VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST PC AUX1 VOL AUX2 TUNER MEMORY DSP PRESET MANUAL CHURCH HALL JAZZ GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C MUTE P-SET VOLUME OPERATION MANUAL MANUEL D’UTILISATION 1 IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. CAUTION 2 Keep these instructions. RISK OF ELECTRIC SHOCK DO NOT OPEN 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 Only use attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. • Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT Please record the serial number of this system in the space below. Model: Serial No.: The serial number is located on the rear of the main unit. Retain this Owner’s Manual in a safe place for future reference. 2 COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Electronics Corp., Address: 6660 Orangethorpe Ave. Buena Park, CA90620 Telephone: 714-522-9105 Type of Equipment: Receiver Model Name: RP-U200 This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See the user manual instructions if interference to radio reception is suspected. FCC INFORMATION (for US customers only) 1. 2. 3. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6660 Orangethorpe Ave. Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. 3 INTRODUCTION About this manual ● This manual explains how to operate this unit. Refer to the separate “SET UP MANUAL” for how to connect this unit with other equipment, and to install the Application Software, etc. to your computer from the supplied CD-ROM. ● This manual mainly explains how to operate this unit using the front panel of this unit and the supplied remote control. ● When this unit and your computer are connected with the USB cable, and the supplied Application Software is installed on the computer, you can operate this unit from the computer using the Application Software. Refer to the online help of the Application Software for how to use the Application Software. The Application Software extends the use of this unit with additional functions which cannot be used with the front panel keys or the remote control. This manual introduces those functions by the following style. Example: Features ● This unit brings high-quality audio to your computer This unit is a multimedia amplifier that brings you a new level of audio enjoyment. This unit has a USB port for connection with a personal computer. The USB interface allows remote control of this unit from your computer and control of sound data sent from your computer. ● Equipped with a five-channel power amplifier This unit has a five-channel power amplifier for reproducing surround sound fields of Dolby Digital*, DTS** and Yamaha CINEMA-DSP effectively. You can enjoy a full-scale home theater sound simply by adding the optional Yamaha speaker system NS-U40P and an optional subwoofer to this unit. ● Equipped with Dolby Digital and DTS decoders This unit reproduces multichannel sources encoded with Dolby Digital* or DTS** faithfully by using the built-in Dolby Digital and DTS decoders. You can now experience the sound scale and the realistic sensation of actual theaters in your home. Adjusting USB MIX LEVEL When an input other than the USB terminal is selected, you can listen to the mixed sound signals from the selected input and from the USB terminal. Also, the mixing ratio of the signals from the USB terminal can be adjusted. * Refer to the online help of the Application Software for details. ● The newly-developed Yamaha Near-Field Cinema DSP (Digital Sound Field Processor) Various DSP sound field programs allow you to select the program suitable for the selected input source. You can experience the sound fields of famous concert halls, movie theaters, etc. around the world in your home. The DSP sound effects are also available for headphone listening. This manual also offers brief explanations about the functions available with the Application Software on page 22–27. Refer to the online help of the Application Software for details of how to use the functions. ● Compatible with various USB audio functions This unit is compatible with the following audio signals received via a USB connection: multi-channel (two, four and six channels) audio, high quality digital audio of 24 bit/48 kHz and Dolby Digitalencoded signals. (Some operating systems and software programs do not support this feature.) ● Various inputs/outputs and easy operation This unit is equipped with various input and output terminals for both analog and digital signals, making it ideal as a control center for other audio equipment, such as a personal computer, CD player and MD recorder. The supplied remote control makes operation easy, and the supplied Application Software allows control of this unit from your computer including detailed settings. ● Compatible with Virtual Dolby Digital and DTS Virtual 5.1 By employing the Virtual 3D technology, this unit reproduces multi-channel sources such as Dolby Digital and DTS providing realistic surround effects even with just two speakers. 4 CONTENTS Main features of this unit .............. 3 Dolby Digital and DTS .................. 4 Virtual 3D ....................................... 5 Digital Sound Field Processing (DSP) ..... 5 Front panel & Remote control ...... 6 About the display .......................... 8 Playing a source ........................... 9 Using sound field programs ...... 11 Recording.................................... 12 Tuning into an FM station........... 14 Using the presets ........................ 16 Adjusting the speaker balance ... 19 Setting USB channel .................. 20 Operating this unit with the Application Software .................. 22 Troubleshooting ......................... 28 Specifications ............................. 31 * Manufactured under license from Dolby Laboratories. APPENDIX APPENDIX ADVANCED OPERATION ADVANCED OPERATION LISTENING TO AN FM BROADCAST LISTENING TO AN FM BROADCAST BASIC OPERATION BASIC OPERATION CONTROLS & THEIR FUNCTIONS CONTROLS AND THEIR FUNCTIONS OUTLINE OF THIS UNIT OUTLINE OF THIS UNIT CAUTION CAUTION ................................ 2 “Dolby”, “AC-3”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. 1992–1997 Dolby Laboratories, Inc. All rights reserved. Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issued and English ** pending. “DTS”, “DTS Digital Surround”, are trademarks of Digital Theater Systems, Inc. Copyright 1996 Digital Theater Systems, Inc. All Rights Reserved. E-1 CAUTION: Read this before operating this unit 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electric shock, do not expose the unit to rain or water. 3. Never open the cabinet. If something drops into the set, contact your dealer. 4. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves. 5. 6. 7. 8. The openings on the unit cover assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the unit will rise rapidly; therefore, avoid placing objects against these openings. To prevent fire or damage, install the unit in a well-ventilated area. <Europe and U.K. models only> To prevent fire or damage, be sure to allow a space of at least 10 cm behind, 10 cm on both sides and 10 cm above the top panel of the unit. The voltage used must be the same as that specified on this unit. Using this unit with a higher voltage than specified is dangerous and may result in fire or other accidents. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than that specified. Always set the volume to minimum before starting audio playback. Increase the volume gradually to an appropriate level after playback has been started. Do not attempt to clean the unit with chemical solvents as this might damage the finish. Use a clean, dry cloth. 9. Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. 10. When not planning to use this unit for a long period (i.e., vacation, etc.), disconnect the AC power plug from the wall outlet. 11. To prevent lightning damage, disconnect the AC power plug when there is an electric storm. 12. Grounding or polarization – Precautions should be taken so that the grounding or polarization of appliances is not defeated. E-2 For U.K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. SPECIAL INSTRUCTIONS FOR U.K. MODEL IMPORTANT: THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. For Canadian Customers To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003. When this unit is turned off by pressing the power switch on the front panel or the POWER key on the remote control, this unit turns into the standby mode. In this mode, this unit is designed to consume a small amount of power. This unit’s power supply is completely cut off from the AC line only when the AC power cord is disconnected. OUTLINE OF THIS UNIT OUTLINE OF THIS UNIT Main features of this unit Although this unit can be used as part of a typical hi-fi system, connecting it to your computer via the USB terminal, and running the supplied Application Software, allows you to remotely control this unit from your computer and make some adjustments and settings. OUTLINE OF THIS UNIT Using Yamaha’s unique DSP technology, this unit can bring excitement and realism to any audio source by simulating the acoustic environments of concert halls, movie theaters, and so on. With its stylish, vertical design, this unit allows you to use various audio sources, including the built-in FM tuner, your computer, CD player, MD or tape deck, as shown below. FM antenna This unit CD player PC AUX1 AUX2 TUNER MD recorder etc. VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST VOL Personal computer DSP STANDBY/ON HIGH CUT 50Hz 150Hz P-SET VOLUME 0 10 SUPERWOOFER SYSTEM YST-SW45 Subwoofer Front speaker (L) Surround speaker (L) * Center speaker Surround speaker (R) English Refer to the separate “SET UP MANUAL” for connections. Front speaker (R) E-3 OUTLINE OF THIS UNIT Dolby Digital and DTS This unit features a built-in Dolby Digital decoder and a DTS decoder for reproducing surround sounds of sources encoded with Dolby Digital or DTS. With such state-of-the-art technologies, this unit can bring the same audio experience to your home as they have brought to feature films in quality theaters around the world. Take some time now to read more about these features and enjoy the new experiences this system brings to your home theater. Dolby Surround Dolby Surround uses four discrete channels and five speakers to reproduce realistic and dynamic sound effects: two main channels (left and right), a center channel for dialog, and a surround channel for special sound effects. The surround channel reproduces sound within a narrow frequency range. Most video tapes and laser discs include Dolby Surround encoding, as do many TV and cable broadcasts. The Dolby Pro Logic decoder built into this unit employs a digital signal processing system that stabilizes each channel for even more accurate sound positioning than is available with standard analog processors. Dolby Digital Dolby Digital is a digital surround sound system that provides completely independent multi-channel audio to you. Dolby Digital provides five full-range channels in what is sometimes referred to as a “3/2” configuration: three front channels (left, center and right), and two surround channels. A sixth bass-only effect channel is also provided for output of LFE (low frequency effect), or low bass effects that are independent of other channels. (This is called the “LFE channel”.) This channel is counted as 0.1, thus giving rise to the term 5.1 channels in total. The wide dynamic range of sound reproduced by the five full-range channels and precise sound orientation by digital sound processing provides listeners with excitement and realism that have never been experienced before. E-4 DTS (Digital Theater System) Digital Surround DTS was developed to replace the analog soundtracks of movies with six discrete channels of digital soundtracks, and it is now installed in many theaters around the world. The DTS digital playback system changed the way we experienced movies in theaters with six discrete channels of superb digital audio. DTS technology, through intense research and development, has made it possible to deliver similar encode/decode discrete technology to home audio surround-sound entertainment. DTS Digital Surround is an encode/decode system which delivers six channels of master-quality, 20-bit audio; technically, it offers 5.1 channels, which means 5 full-range (left, center, right and two surround) channels, plus a subwoofer (LFE) channel (as “0.1”). It is compatible with the 5.1 speaker configurations that are currently available for home theater systems. OUTLINE OF THIS UNIT Virtual 3D FL C FR Virtual 3D, which is used by this unit’s sound field programs, simulates the surround effect provided by surround and center speakers, creating “virtual” surround speakers, as shown, so even with only two front speakers, you can still enjoy surround sound. FL C OUTLINE OF THIS UNIT Surround sound typically requires several speakers situated in front of and behind the listening position, which requires a substantial amount of space that may not always be available. In addition to ordinary surround sound reproduction using several speakers, this unit enables you to enjoy surround sound effects with only two speakers by using Yamaha’s unique “Virtual 3D” (three-dimensional) technology. FR Virtual speakers RL RR RL Typical surround system RR Virtual 3D Digital Sound Field Processing (DSP) When you listen to a performance in a concert hall, jazz club, or other live music venue, you not only hear the direct sound coming from the musical instruments and singers, but also the “early reflections” and natural reverberation. Early reflections are the initial sound waves that bounce off the floor, ceiling, and walls. Natural reverberation is made up of sound waves that gradually attenuate as they bounce repeatedly off multiple surfaces. Since the way you hear early reflections and reverberation depends on the shape and size of the building as well as the material and construction of the walls and ceiling, each venue has its own unique “sound,” called its “sound field.” At Yamaha, we have measured all the elements that make up a typical sound field—direction and level of the reflections, band-width characteristics, and delay times—at famous concert halls and opera houses around the world. The information gained in this process has been converted into programs that can be reproduced using Yamaha’s DSP technology. Using its on-board DSP, this unit can process any audio source and recreate the atmosphere of the original venue. Early sound reflections Reverberation English Direct sound E-5 CONTROLS AND THEIR FUNCTIONS CONTROLS AND THEIR FUNCTIONS Front panel & Remote control Remote control Front panel POWER 8 PC PC 1 AUX1 AUX1 AUX2 1 AUX2 TUNER TUNER 9 4 2 VIRTUAL PRESET MANUAL HALL JAZZ CHURCH GAME MOVIE LIVE / D TS SURROUND TEST ON/OFF A B C D E 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST 0 VOL 3 DSP A P-SET 4 5 3 B C MUTE VOLUME 6 6 7 8 1 Input selectors & indicators These four keys, explained below, are used to select the input source. The indicator of the selected source lights up. ● PC key This key selects your computer as the input source. Pressing this key repeatedly selects the signals received at the USB, digital (DIGITAL PC COAX IN or DIGITAL PC OPT IN) or analog (ANALOG PC IN) input. The DIGITAL PC OPT IN has priority over the DIGITAL PC COAX IN, so if you connect to both inputs, the signal received at the DIGITAL PC OPT IN is used. E-6 MEMORY ● AUX1 key This key selects the equipment connected to the ANALOG AUX 1 IN or DIGITAL AUX 1 OPT IN connector as the input source. Pressing this key repeatedly selects the digital or analog input. ● AUX2 key This key selects the equipment connected to the ANALOG AUX 2 IN connectors as the input source. ● TUNER key This key selects the built-in FM tuner as the input source. If the tuner is already selected, this key toggles the reception mode between FM auto stereo and FM monaural. CONTROLS AND THEIR FUNCTIONS 2 Display A TEST key The display shows various settings, selected input source, sound field program and various other information. 3 DSP key [front panel] ON/OFF key [remote control] This key activates the sound field programs produced by the internal DSP. 4 P-SET key ( ) [front panel] PRESET key [remote control] 5 / (Down/Up) keys These keys are used for selecting sound field programs, changing station frequencies, selecting preset station numbers, etc. 6 Volume control [front panel] VOLUME (Down/Up) keys [remote control] These control and keys adjust the speaker and headphone volume. The volume cannot be adjusted when this unit is in the standby mode. 7 Headphone jack Stereo headphones can be connected to this mini-jack for private listening, with Virtual 3D effects specifically tailored for headphone listening. 8 Power switch ( ) [front panel] POWER key [remote control] Each click of this switch changes the status of this unit between standby mode and power on. * In the standby mode, this unit can be turned on remotely from your computer, using the supplied Application Software. Note that this unit uses a small amount of power in the standby mode. 9 MEMORY key This key is used to store a desired station in the memory. * This key works only when the tuner is selected as the input source. B Custom keys (A, B, C) These keys are available when this unit and your computer are connected with the USB cable, and the supplied Application Software is installed on the computer. Each of these keys can be programmed with a set of commands (input selector, sound field program, volume setting, etc.) by using the Application Software. After storing, simply pressing each key will execute the stored command. * Refer to the online help of the Application Software for details. CONTROLS & THEIR FUNCTIONS This key changes the display status of the built-in FM tuner from the frequency display mode to the preset tuning mode. If the tuner is already in the preset tuning mode, each press of this key changes the group of preset stations (A, B, C, D, E). * This key works only when the tuner is selected as the input source. This key is used to output a test tone. The test tone is used when adjusting the volume balance among all speakers in the system including the virtual surround speakers. (Refer to page 19 for details.) C MUTE key This key is used to cut off sound output temporarily. Turning the volume control on the front panel or pressing the VOLUME keys on the remote control restores sound output. Pressing this key again also restores sound output. * Sound output will also be restored by changing the status of this unit between standby and power-on, changing the input source or the sound field program, and so on. D MANUAL key This key changes the display status of the built-in FM tuner from the preset tuning mode to the frequency display mode. * This key works only when the tuner is selected as the input source. E Tuning / (Down/Up) keys These keys work in the following ways according to the status of the tuner. In the frequency display mode: Each press of selects a higher frequency and selects a lower frequency. In the preset tuning mode: Each press of selects a higher preset station number and selects a lower preset station number. 0 Sound field program selector keys English Each of these keys selects the corresponding sound field program. E-7 CONTROLS AND THEIR FUNCTIONS About the display This section explains what the various display indicators mean. 1 2 3 45 6 7 A B C D VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM ST 8 9 0 VOL E 1 VIRTUAL 9 This indicator appears when this unit is using Virtual 3D. 2 USB This indicator appears when audio signals are sent or received via the USB terminal. * If you use a Macintosh computer, this indicator is always illuminated when this unit is connected to the computer via the USB terminals. 3 4 PCM This indicator appears when a PCM digital audio signal is selected as the input source. This indicator appears when a stereo broadcast is received in stereo mode. A (DOLBY) DIGITAL This indicator appears when an input signal is decoded with Dolby Digital. B (DOLBY) PROLOGIC This indicator appears when an input signal is decoded with Dolby ProLogic. C FM This indicator appears when the built-in FM tuner is 5 selected as the input source. This indicator appears when headphones are connected to the headphone jack of this unit. 6 5.1CH This indicator appears when a 5.1 channel digital audio signal is selected as the input source. 7 DSP This indicator appears when the DSP is processing the input signal. 8 Sound output indicator E-8 0 ST (DTS) This indicator appears when an input signal is decoded with DTS. D. This indicator appears when an audio signal encoded with Dolby Digital is selected as the input source. This indicator shows the currently used speakers. A red dot shows that the corresponding speaker is currently used, or the speaker is set for use in the Application Software. The mark shows that sound is outputted. * When using the test tone, a red dot shows the channel currently outputting the test tone. * When using headphones, only the two dots for the left and right front speakers appear regardless of the setting in “Speaker Settings”. D Multi-information display Various messages and information appear here. E VOL (volume) This indicator graphically displays the volume level setting. Note The indicators , “5.1CH” and will not appear when sound signals are decoded on the computer (by using DVDplayback software, etc.). BASIC OPERATION BASIC OPERATION Playing a source This section explains how to turn on this unit and select input sources. If any external audio equipment is connected to this unit, turn it on first. POWER 4 Start the selected input source. Refer to “Listening to an FM broadcast” on pages 14–18 about how to tune into a desired station. 1 PC PC AUX1 AUX2 3 AUX1 3 AUX2 TUNER 5 Adjust the volume to the desired level. TUNER MEMORY PRESET MANUAL HALL JAZZ GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C VOLUME or CHURCH VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST VOL DSP P-SET MUTE VOLUME Front panel 2, 5 6 2, 5 As you prefer, use a sound field program. Refer to page 11 for details about the sound field programs. Each of the input selector keys selects the following input signals. PC: Turn on this unit. POWER or Front panel Press the PC key repeatedly to select the PC inputs: “USB”, “PC_DIGT” and “PC_ANLG”. PC_DIGT selects the DIGITAL PC COAX IN or DIGITAL PC OPT IN, and PC_ANLG selects the ANALOG PC IN. Note: The DIGITAL PC OPT IN has priority over the DIGITAL PC COAX IN, so if you connect to both inputs, the signal received at the DIGITAL PC OPT IN is used. BASIC OPERATION About the input selector keys 1 1 Remote control Remote control The message “Hello” appears for a few seconds, and this unit returns to the state in which it was last used (e.g., the input source that was selected when this unit was turned off VOL is selected). 2 Decrease the volume to minimum (MIN). VOL AUX1: VOLUME or Front panel 3 The corresponding indicator on the front panel lights up. PC AUX2: AUX1 or TUNER: AUX2 TUNER Remote control Press the AUX2 key to select the equipment connected to the ANALOG AUX 2 IN connectors as the input VOL source. Press the TUNER key to select the built-in FM tuner as the input source. * When the TUNER key is pressed, “TUNER” appears first on the display, and then changes to the display of a frequency or a preset station. Refer to the explanation on the right side for details about using the input selector keys. FM VOL ST FM VOL English TUNER VOL VOL PC AUX1 Front panel Press the AUX1 key repeatedly to select the inputs: “AUX1_DG” and “AUX1_AN”. AUX1_DG selects the equipment connected to the DIGITAL AUX 1 OPT IN, and AUX1_AN selects the equipment connected to the ANALOG AUX 1 IN connector as the input source. Remote control Select an input source by using the input selector keys. AUX2 VOL ST E-9 BASIC OPERATION When you have finished using this unit Note When the PC, AUX1 or AUX2 input selector key is pressed, the display shows the name of the selected input source for a short while, and then shows the currently selected sound field program. When no sound field program is selected, “THROUGH” is shown on the display. Set this unit to the standby mode by pressing the power switch on the front panel or the POWER key on the remote control. POWER or Front panel The names of input sources shown on the display can be changed with the Application Software. Refer to the Online Help of the Application Software for details. Remote control Note When not planning to use this unit for a long period (i.e., vacation, etc.), disconnect the AC power plug from the wall outlet. To cut off sound output temporarily Press the MUTE key. To restore sound output, turn the volume control on the front panel or press the VOLUME keys on the remote control. Pressing the MUTE key again also restores sound output. MUTE Remote control Note Sound output will also be restored by changing the status of this unit between standby and power-on modes, changing the input source or the sound field program, using the test tone, or using the A, B, C keys on the remote control. When you listen with headphones Connect the headphones to the headphone jack. No sound will be outputted from the speakers. Setting USB MIX When an input other than the USB terminal is selected, you can listen to the mixed signals from the selected input and from the USB terminal. Also, the mixing ratio of the signals from the USB terminal can be adjusted. * Refer to the online help of the Application Software for details. Setting graphic equalizer You can adjust the frequency characteristics as you prefer by using the 7-band graphic equalizer. * Refer to the online help of the Application Software for details. Notes ● Some setting changes may be needed on the computer to reproduce signals sent from the computer to this unit via the USB connection. Refer to the separate “SET UP MANUAL” for details. ● Some setting changes may be needed on the computer to reproduce signals sent from the computer to this unit via a sound card, etc. Automatic power saving function If there is no operation on this unit’s front panel, the remote control or the Application Software for about 24 hours with the power of this unit on, this unit will automatically be set to the standby mode. E-10 BASIC OPERATION Using sound field programs This unit’s built-in DSP (Digital Sound field Processor) can simulate various acoustic environments, including a concert hall and movie theater, with its seven sound field programs. For the best results, choose a program appropriate for the selected audio source. First follow steps 1–5 of “Playing a source” on page 9. POWER 1 Turn on the DSP. PC (When using the remote control, step 1 can be skipped.) PC DSP AUX1 AUX1 AUX2 AUX2 TUNER TUNER MEMORY PRESET MANUAL HALL JAZZ CHURCH Front panel VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST VOL 1 DSP P-SET 2 GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C MUTE The name of the selected sound field program appears on the display. 2 2 Select the desired sound field program. VOLUME HALL JAZZ CHURCH GAME MOVIE LIVE / D TS SURROUND TEST ON/OFF or BASIC OPERATION Front panel Remote control Front panel: Pressing or repeatedly changes the program. Remote control: Press the key of the desired program. DSP Active program VOL The following programs are available. Feature Note HALL (CONCERT HALL EUROPE) This program simulates the sound field of a mediumsized hall, with a beautiful and rich reverberation. JAZZ (JAZZ CLUB VILLAGE GATE) This program simulates the sound field of a famous New York jazz club. CHURCH (CHURCH ROYAUMONT) This program simulates the sound field of a Gothic church, with the unique effect of sound reverberating back and forth in a domed ceiling. GAME (GAME AMUSEMENT) This program adds depth and surround effects to These programs can be used computer games, enhancing the gaming experience. together with Dolby Pro Logic, Dolby Digital or DTS for enjoying The realism provided by this program gives the surround sounds of motionimpression that you’re actually in the scene. picture audio. This program produces an enthusiastic atmosphere *: HP3D and lets you feel that you are in the midst of the This program enables you to action, as if attending an actual jazz or rock concert. enjoy a virtual 3D effect with This program reproduces the surround sound of a headphones. When you source encoded with Dolby Pro Logic, Dolby Digital connect headphones to this or DTS faithfully. Sensing the input signal, the built-in DTS SUR. unit, the Dolby Digital decoder or the DTS decoder program automatically automatically works. changes to HP3D . When this unit is set to the “Virtual 3D” mode (the surround speakers are not used) in the Application Software, 5.1-channel surround sound effects are reproduced with only two front speakers by using Yamaha’s “Virtual 3D” technology. MOVIE (MOVIE THEATER) LIVE (LIVE CONCERT) DTS SUR.) NORMAL ( [HP3D* (Headphone 3D) ] These programs create a sound field that feels real, just as if you were actually there. English CINEMA DSP (for video sources) Hi-Fi DSP (for music sources) Program E-11 BASIC OPERATION Notes ● Just after selecting a program, the program name scrolls from right to left on the display, and then its short-version name lights up. ● No sound field program can be used when receiving signals with a 96 kHz sampling frequency. To turn off the sound field effect Press the DSP key on the front panel or the ON/OFF key on the remote control. “THROUGH” appears on the display. ON/OFF DSP or Front panel Remote control Adjusting DSP sound field parameters The surround effect of each program or the Virtual 3D effect can be adjusted to the desired taste by using the Application Software. Refer to the online help of the Application Software for details. Note When the sound field effect is off, sound is reproduced in normal stereo. Recording Input sources (e.g., a computer or CD player) selected on this unit can be recorded by an MD recorder, tape deck, etc. connected to this unit. Also, input signals can be fed to your computer via the USB connection. * When a source is recorded using a sound field program, sound field effects are recorded with the source. First turn on the external unit to be used, and then this unit. 1 Select the source to be recorded by using the input selector keys. PC PC AUX1 Recording on an external recording unit AUX2 AUX1 or AUX2 TUNER POWER TUNER Front panel PC PC AUX1 AUX2 AUX1 1 1 AUX2 TUNER TUNER MEMORY PRESET MANUAL CHURCH HALL JAZZ GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST VOL DSP Remote control 2 Start recording on a recording unit (an MD recorder, tape deck, etc.). 3 Start playing the input source . P-SET Playing the recorded result via this unit MUTE VOLUME Select the input signals sent from the recording unit with the input selector keys. Notes E-12 ● If input signals received at any digital input terminal other than the USB terminal is outputted at the digital output terminal, the sampling frequency for the output signals is the same as that for input signals. ● The sampling frequency for digital signals converted from analog signals on this unit is 44.1 kHz or 48 kHz. ● When digital input signals are outputted at the digital output terminal, track information (CD-text data, automatic track renewal when recording is made on an MD, etc.) is invalid if any sound field program (including the graphic equalizer effect) is used. ● Both REC OUT and OPT OUT terminals on the rear of this unit output the same constituents of signals as outputted from the left and right front speakers. BASIC OPERATION Recording on a computer (via the USB connection) When recording or processing signals inputted to your computer via the USB connection, the following setting is needed on the computer. 1 Select the source to be recorded by using the input selector keys. PC Selecting Recording Device When using Windows 1. Click the Windows “Start” button and select “Settings”, and then “Control Panel”. 2. Double-click the “Multimedia” icon (or the “Sounds and Multimedia” icon). 3. Click the “Audio” tab and select “USB Audio Device” at “Preferred device” of “Recording” (or “Sound Recording”). When using a Macintosh Select “USB Audio” as the input device at “Sound” on the Control Panel. PC AUX1 AUX1 or AUX2 AUX2 TUNER TUNER Front panel Remote control 2 Start recording with the recording software on the computer. 3 Start playing the input source. Setting of Recording Software POWER PC PC AUX1 AUX2 AUX1 1 1 AUX2 TUNER TUNER MEMORY PRESET MANUAL CHURCH HALL JAZZ GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST VOL DSP P-SET MUTE VOLUME Playing the recorded result via this unit Press the PC input selector key repeatedly to select USB as the input source, and play the recorded result on the computer. Notes ● If the number of USB channels is set to six, recording cannot be made via the USB connection. Reset the number of USB channels to two or four. ● To record digital input signals with a 48 kHz sampling frequency, the frequency of the input signals must be 48 kHz. ● To record sound signals received at an analog or digital input of the sound card etc., and not via the USB connection, select the corresponding device, such as “Sound Card”, from “Preferred device” of “Recording” (or “Sound Recording”) on the computer. ● The sampling frequency and resolution of signals recordable on the computer differ from operating systems. You can refer to the following Yamaha website for details about the related information. BASIC OPERATION Select a sampling frequency from 44.1 kHz and 48 kHz. Select a resolution from 16 bits and 24 bits. The sampling frequency of 44.1 kHz with the resolution of 16 bits produces a sound quality comparable to the compact disc (CD). http://www.yamaha.co.jp/audio/ English Notes ● Please check the copyright laws in your country before recording compact discs, radio, etc. Recording of copyright material may infringe copyright laws. ● You cannot make a recording from a CD-R, MD, etc. which is a copy of an audio CD, to another CD-R, MD, etc. via the USB connection or the digital terminal connection. Also, you cannot make a recording from an MD which is recorded with digital signals received via the USB connection, to another MD via a digital connection. E-13 LISTENING TO AN FM BROADCAST LISTENING TO AN FM BROADCAST Tuning into an FM station Normally, if station signals are strong and there is no interference, quick auto tuning is possible. However, if the signal of the station you want to select is weak or the reception condition is bad, you must tune in to it manually. POWER PC PC AUX1 AUX1 AUX2 AUX2 TUNER 1, 2, 3 2 1 2, 3 4 TUNER MEMORY PRESET MANUAL CHURCH HALL JAZZ GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST VOL DSP P-SET PC AUX1 4 MUTE If the tuner is in the preset tuning mode, press the TUNER key (front panel) or the MANUAL key (remote control) to change the preset tuning mode to the frequency display mode. AUX2 VOLUME MANUAL or TUNER Front panel 3 Auto tuning Remote control Press the TUNER key (front panel) or the MANUAL key (remote control) to select the desired reception mode: FM auto stereo or FM monaural. First turn on this unit. PC 1 Press the TUNER input selector key to select the built-in FM tuner. AUX1 AUX2 PC PC AUX1 AUX2 AUX1 or Front panel AUX2 TUNER Remote control The tuner turns on in either of the following modes. (The mode which was selected the last time you used the tuner is selected.) ● Frequency display mode The display shows the selected frequency. This mode is for tuning into a station by changing the frequency. ● Preset tuning mode This mode is for tuning into a preset station which is already stored in the memory. The display shows the preset group (A to E), the number (1 to 8) and the frequency of the preset station. E-14 Remote control The reception mode changes alternately by each press of the TUNER key. TUNER Front panel MANUAL or TUNER FM ST FM ST VOL ● FM auto stereo When a stereo broadcast is received, it is received in stereo automatically. (The “ST” indicator lights up on the display.) If, however, the signal of a stereo broadcast is weak, it may be received in monaural automatically. (In this case, the “ST” indicator goes off.) ● FM monaural Any broadcast is received in monaural. (On the display, “M” appears above the frequency.) If you hear noise in the FM auto stereo mode, try switching to FM monaural. FM auto stereo FM FM monaural ST FM VOL (U.S.A. model) VOL VOL LISTENING TO AN FM BROADCAST 4 Press the or second or more. key and keep it pressed for one Manual tuning First turn on this unit. 1 Press the TUNER input selector key to select the built-in FM tuner. or PC Front panel Remote control PC AUX1 AUX1 or AUX2 key to search for lower frequencies and the Press the key for higher frequencies. When a station with a strong signal is found, the search stops and the station is received. If no station with a strong signal is found, the search stops after searching through all frequencies. 5 If the received station is not the desired one, repeat step 4. AUX2 TUNER TUNER Front panel 2 Note If the desired station cannot be found by the auto tuning method, search for the station by using the manual tuning method. Remote control If the tuner is in the preset tuning mode, press the TUNER key (front panel) or the MANUAL key (remote control) to change the preset tuning mode to the frequency display mode. PC AUX1 AUX2 MANUAL or TUNER 3 Remote control Press the TUNER key (front panel) or the MANUAL key (remote control) to select the desired reception mode: FM auto stereo or FM monaural. PC LISTENING TO AN FM BROADCAST Front panel AUX1 AUX2 MANUAL or TUNER Front panel 4 Frequency range and tuning step Frequency range Tuning step U.S.A. and Canada models 87.50–107.90 MHz 0.20 U.K. and Europe models 87.50–108.00 MHz 0.05 Australia model 87.50–108.00 MHz 0.10 Remote control Press the or key repeatedly until the desired frequency is located. or Front panel Remote control Press the key to search for lower frequencies and the key for higher frequencies. English E-15 LISTENING TO AN FM BROADCAST Using the presets You can store your favorite stations in the 40 presets, which are organized into five groups (A–B), with eight presets in each group. A stored station can be recalled simply by selecting the preset number in which it is stored. Storing stations manually 3 POWER PC PC AUX1 AUX1 Press the P-SET key (front panel) or the PRESET key (remote control) repeatedly to select the desired preset group from A through E. AUX2 AUX2 PRESET TUNER P-SET TUNER 2, 5 MEMORY PRESET MANUAL HALL JAZZ GAME MOVIE CHURCH LIVE / DTS SURROUND TEST ON/OFF A B C VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST VOL DSP 3 4 P-SET 2, 3, 5 4 MUTE or Front panel 4 Remote control Press the key or the key repeatedly to select the desired preset number from 1 through 8. VOLUME or Front panel 5 First turn on this unit, and then select the built-in FM tuner Remote control Press the P-SET key (front panel) or the MEMORY key (remote control) and keep it pressed for one second or more. as the input source. MEMORY P-SET 1 In the frequency display mode, tune into the desired station and select the reception mode: FM auto stereo or FM monaural. * 2 Refer to pages 14 to 15 on how to tune into a station and select the reception mode. Press the P-SET key (front panel) or the MEMORY key (remote control) and keep it pressed for one second or more. MEMORY P-SET or Front panel FM ST VOL E-16 Front panel Remote control “MEMORY” lights up on the display for approx. 2 seconds to show that the station has been stored. Notes ● A newly stored station overwrites the previously stored one in the same preset group and number. ● To abort storing the station, press an input selector key (except the TUNER key). The selected input mode appears. Remote control A preset group and a preset number appears and an arrow scrolls from right to left on the display. This means that storing a station is possible. Preset group or Preset number (U.S.A. model) With the supplied Application Software, you can use the auto preset tuning function in addition to the manual method. The auto preset function searches for all stations available in your area and automatically stores them in the presets. Also, the Application Software allows you to assign a name to each preset station. The names are displayed on the monitor when running the Application. Refer to the online help of the Application Software for details. LISTENING TO AN FM BROADCAST Recalling a preset station First turn on this unit, and then select the built-in FM tuner as the input source. POWER 1 PC PC AUX1 AUX1 AUX2 AUX2 TUNER TUNER MEMORY PRESET MANUAL Press the P-SET key (front panel) or the PRESET key (remote control) to change this unit from the frequency display mode to the preset tuning mode. PRESET 1, 2 P-SET HALL JAZZ CHURCH GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST VOL DSP 1, 2 3 or Front panel P-SET Remote control 3 MUTE VOLUME 2 Press the P-SET key (front panel) or the PRESET key (remote control) repeatedly to select the preset group from A through E. PRESET P-SET or Front panel 3 Remote control Press the key or the key repeatedly to select the preset number from 1 through 8. Front panel Remote control The station stored in the selected preset group and number is selected. LISTENING TO AN FM BROADCAST or English E-17 LISTENING TO AN FM BROADCAST Copying a preset station to a different group and number You can copy a preset station to a different group and number. Using this function, you can arrange preset stations in your favorite order or collect preset stations into genres. 3 Press the P-SET key (front panel) or the MEMORY key (remote control) and keep it pressed for one second or more. An arrow scrolls from right to left on the display. POWER PC MEMORY PC P-SET AUX1 AUX1 AUX2 AUX2 3, 5 1, 2, 4 VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST VOL DSP or TUNER TUNER MEMORY PRESET MANUAL HALL JAZZ CHURCH GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C P-SET 2, 4 1, 2, 3, 4, 5 MUTE Front panel 2, 4 4 VOLUME Remote control Use the P-SET (or PRESET) key to select the preset group, and use the / keys to select the preset number you want to copy the station to. PRESET P-SET or First turn on this unit, and then select the built-in FM tuner Front panel as the input source. 1 Press the P-SET key (front panel) or the PRESET key (remote control) to change this unit from the frequency display mode to the preset tuning mode. PRESET P-SET 5 Press the P-SET key (front panel) or the MEMORY key (remote control) and keep it pressed for one second or more. MEMORY P-SET or Front panel 2 or Remote control Use the P-SET (or PRESET) key to select the preset group, and use the / keys to select the preset number of the station you want to copy. PRESET P-SET or Front panel E-18 Remote control Remote control Front panel Remote control “MEMORY” lights up on the display for approx. 2 seconds to show that the station has been copied and successfully stored. ADVANCED OPERATION ADVANCED OPERATION Adjusting the speaker balance This procedure lets you adjust the sound output level balance between the front, center and surround speakers by using the built-in test tone generator. Make this adjustment so that each speaker output level is about the same when heard at the listening position. This is important for high performance of the built-in DSP (Digital Sound field Processor), the Dolby Digital decoder and the DTS decoder. If this unit is set to the “Virtual 3D” mode (the surround speakers are not used) in the Application Software, you can adjust the sound output levels of the speakers in the sound field of the “Virtual 3D” mode (including two virtual surround speakers). Refer to “Setting adjustment on the Setup panel” on page 27. This setting cannot be made by using the front panel controls or the remote control.) * Use the remote control for adjusting the speaker output levels at the listening position. 2 POWER PC AUX1 AUX2 TUNER MEMORY PRESET MANUAL HALL JAZZ CHURCH GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C When the test tone is outputted from the left (L ch) or right (R ch) front speaker: Use the VOLUME keys on the remote control to adjust the volume of each speaker. In this step, adjust the volume balance between the left and right front speakers. (Adjustable range: –10 to 0) MUTE VOLUME Remote control 1, 5 2, 3, 4 VOLUME 3 When the test tone is outputted from the center speaker (Cch): Use the VOLUME keys on the remote control to adjust the center speaker output level. Make the sound output level of the center speaker about the same as the left or right front speaker. (Adjustable range: –20 to +10) VOLUME Remote control Press the TEST key on the remote control. TEST Remote control * 4 You will hear a test tone (so called pink noise) from each speaker for about two seconds in the following order. When the test tone is outputted from the left (Ls ch) or right (Rs ch) surround speaker: Use the VOLUME keys on the remote control to adjust the volume of each speaker. Make the sound output level of the surround speakers about the same as the front speakers. ADVANCED OPERATION 1 (Adjustable range: –20 to +10) Front speaker (L) Center speaker Front speaker (R) VOLUME Remote control Surround speaker (L) * Surround speaker (R) The speaker currently outputting the test tone is shown on the display. 5 When the adjustments are finished, press the TEST key. TEST English Remote control The test tone stops. E-19 ADVANCED OPERATION Notes ● When this unit is set to the “Virtual 3D” mode: The output order of the test tone is as follows. When using a center speaker: Front speaker (L) Virtual surround speaker (L) Virtual surround speaker (R) Center speaker Front speaker (R) When not using a center speaker: Front speaker (L) Virtual surround speaker (L) Front speaker (R) Virtual surround speaker (R) ● Adjust the subwoofer level while listening to a suitable source. With the supplied Application Software, you can select the speakers to use and not to use. Also, by designating the size of the speakers to use, this unit can be set to an output mode suitable for the ability of the speakers. Setting USB channel Typical USB audio features multi-channel modes, such as four-channel and six-channel modes, in addition to a normal twochannel (stereo) mode. This unit is compatible with each of these modes. When a multi-channel mode is selected, you can receive the surround sound signals of computer games compatible with the 4ch Direct Sound 3D and the multichannel signals of DVD video on this unit via the USB connection and enjoy them in surround sounds. Note that some operating systems and software programs are not multi-channel compatible. Yamaha websites list the names of multi-channel compatible operating systems and software. Notes ● MacOS9.04, 9.1, etc. does not support this feature. Only the two-channel mode can be used. Some versions of Windows also do not support the six and/or four-channel modes. You can refer to the following Yamaha website for details and related information. http://www.yamaha.co.jp/audio/ ● When the six channel mode is selected, recording cannot be made to the computer. To record, select the two- or four-channel mode. E-20 ADVANCED OPERATION 4 PC Press or repeatedly until the desired number of channels is shown on the display. 2, 3, 5 AUX1 Front panel AUX2 TUNER The display changes as follows. VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST VOL DSP P-SET 4 5 Hold down the PC input selector key until the following indication appears on the display. 1 PC AUX1 How to set * AUX2 When playback or recording is performed on the computer via the USB connection, terminate the playback or recording software used on the computer. 1 Front panel Turn on this unit. Front panel 2 TUNER Press the PC input selector key repeatedly until “USB” appears on the display. The number of channels before the change The number of channels after the change Although no further operation is required, wait a short time AUX1 AUX2 TUNER 3 Front panel Hold down the PC input selector key until the current channel setting is shown (for about two seconds). Notes ● When the number of channels is changed for the first time, the device driver for the USB audio is installed in the computer. Wait a short time until the computer completes the changes in the setting. ● Do not change the USB channel setting under any circumstance during playback or recording via the USB connection on the computer. If changed, the computer may freeze. ADVANCED OPERATION until the computer completes the changes in the settings. PC PC AUX1 AUX2 TUNER Front panel computer. English * When the display of this unit shows “USB” in red, USB audio is being played back, disabling this USB channel setting function. Terminate the software used on the E-21 ADVANCED OPERATION Operating this unit with the Application Software If this unit is connected to your computer via the USB connection and the Application Software is installed in your computer from the supplied CD-ROM, you can operate this unit with the Application Software from your computer. Moreover, the Application Software, once installed on your computer, offers various settings unavailable from this unit or the remote control. (For instructions on how to install the Application Software, see the separate “SET UP MANUAL”.) About the Main Panel This section briefly explains how to use the Application Software, the setting screens, and the available functions. For further details, refer to the Online Help of the Application Software. Notes ● The screen images shown in this section are of the basic screens for the Windows version. The Macintosh version slightly differs in button arrangement, etc. ● The screen design, functions, etc., are subject to change due to version upgrades. The Main Panel allows you to perform the following basic operations. Tabs are shown at the bottom of the detailed-setting screen. To make detailed settings of the desired function available from any detailed-setting screen, click on the tab for the function. 1 5 2 6 7 3 8 9 1 Display 4 This section shows the current status of the volume, input selectors, sound field programs, etc. by characters. 2 Input selector The input selector allows you to directly change the input source. 3 Volume control You can adjust the volume by dragging the indicator or by clicking the up ( ) and down ( ) arrows. You can also alternately turn on and off the speakers by clicking the speaker icon below. 4 Changing the panel size You can minimize the size of the Main Panel. 5 Opening the tuner panel Press this button to open the tuner panel. (See page 26 for details on operating the FM tuner.) 6 SETUP Open this panel to change available settings in the Setup panel. (See page 27 for details on the Setup panel.) 7 DSP selector You can directly select a DSP sound field program. 8 Detailed-setting screens Select one of the detailed-setting screen tabs at the bottom of the current detailed-setting screen. The new detailed-setting screen will be displayed, where you can make detailed settings of the function. DSP-EDIT: For adjusting the DSP sound field parameters (See page 23.) SPEAKER: For adjusting the speaker output levels or the virtual 3D effect (See page 24.) D-RANGE: For adjusting the dynamic range (See page 25.) EQUALIZER: For operating the graphic equalizer (See page 25.) 9 POWER E-22 Each click changes the status of the main unit between standby and power-on. ADVANCED OPERATION Adjusting DSP sound field parameters You can adjust various parameters of the DSP sound field programs. The default parameters of the sound field programs provide great sound, but it is also possible to fine-tune the parameters to suit the acoustics of the room, individual preferences, and program source. Parameter adjustment is required for each selected sound field program. How to adjust parameters 1. Select the program whose parameters you wish to adjust. (Parameter adjustment is effective for the currently selected program only.) 2. Select the DSP-EDIT tab at the bottom of the Main Panel. The basic parameter screen appears. 3. This screen allows you to adjust the basic parameters. Open the “ADVANCED SETTING” panel for adjusting the detailed parameters. Basic parameters Opens the “ADVANCED SETTING” panel. Basic parameters Effect Level Selects the level of effect sound from the three levels. Room Size Selects the apparent size of the listening space from the three levels. Seat Position Selects the simulated listening position from the three positions. Restores all parameters to their default values. Restores the basic parameter screen. ADVANCED OPERATION Select a parameter by clicking its name, and adjust the parameter by sliding the indicator at the bottom of the panel. Detailed parameters The following parameters are available on the “ADVANCED SETTING” panel. Depending on the selected program and input signals, not all of the parameters can be adjusted. Makes fine adjustment of the level of the overall effect sound. Rear Effect Trim Makes fine adjustment of the level of the rear effect sound. Initial Delay Adjusts the apparent distance from the sound source to the walls. Room Size Adjusts the apparent size of the listening space. Liveness Adjusts the apparent reflectivity of the walls. Surround Delay Adjusts the delay time of the surround sound field. S. Initial Delay (Surround Initial Delay) Adjusts the initial delay time of the surround sound field. (This parameter can be adjusted only when the “Speaker Settings” of this unit has been set to two front and two surround channels or more, and Dolby Digital- or DTS-encoded signals are inputted.) S. Room Size (Surround Room Size) Adjusts the apparent size of the surround sound field. Reverb Time Adjusts the duration of reverberations. Reverb Level Adjusts the level of reverberations. Reverb Delay Adjusts the delay time of reverberations. English Effect Trim E-23 ADVANCED OPERATION Adjusting the speaker output levels and effect levels When the check box “Use the surround speakers” under “Speaker Settings” in the Setup panel is checked, you can adjust the output levels of the available speakers respectively. When the check box is not checked, this unit is in the virtual 3D mode, allowing adjustment of the virtual 3D effects. (See page 27.) Select the SPEAKER tab at the bottom of the Main Panel. The following screen appears. Adjusting the output levels of the speakers You can adjust the output levels of the speakers which are set for use under “Speaker Settings” in the Setup panel. 1 2 3 1 2 3 4 5 4 5 Adjusting the output levels of the main speakers You can adjust the output levels of the left and right main speakers. Adjusting the output level and the delay time of the center speaker You can adjust the output level and the delay time of the center speaker. Test tone Click on “Test tone” to output the test tone from the respective speakers in turn. You can adjust their levels while listening to the test tone. On the figure of the speakers at the center of the screen, the speaker currently outputting the test tone is indicated. Adjusting the output levels of the surround speakers You can adjust the output levels of the left and right surround speakers. Adjusting the LFE output levels You can adjust the output level of the LFE (Low Frequency Effect) sounds reproduced when playing a Dolby Digital- or DTS-encoded source. The levels can be adjusted for Dolby Digital and DTS respectively. Adjusting the virtual 3D effect The surround sound effect of the virtual 3D sound field is affected by the room configuration, the position of the front speakers and the position of the listener, resulting in sound unique to each environment. The procedure below shows you how to adjust the effect of the virtual 3D to suit your preferences and environment. Select the VIRTUAL tab at the bottom of the Main Panel. The following screen appears. 1 1 3 2 2 4 3 4 E-24 Balance adjustment You can adjust the volume balance between the right and left speakers. Virtual surround speaker position setting You can set the position of the virtual surround speakers (the speakers are positioned symmetrically.) HRTF (Head-related Transfer Function) adjustment You can make an adjustment to personal characteristics. Test tone You can output a test tone successively from the speakers at their current positions, allowing setting and adjustment while listening to the tone. ADVANCED OPERATION Adjusting the dynamic range You can set the dynamic range for playing a source with Dolby Digital decoded. This is especially effective for low-volume listening. Select the D-RANGE tab at the bottom of the Main Panel. The following screen appears. 1 1 2 2 Dynamic range setting Select the dynamic range for playing a source with Dolby Digital decoded from MIN, STANDARD, and MAX. The MAX setting provides a dynamic range of a movie theater while MIN provides a dynamic range suitable for late night, low-volume listening. Dynamic range adjustment This setting becomes available when you choose STANDARD for the dynamic range. This adjusts highlevel cut scale (H-LEVELCut) and low-level boost scale (L-LEVELBST), allowing you to freely adjust the dynamic range between MAX and MIN. Operating the graphic equalizer The 7-band graphic equalizer allows you to set the frequency characteristics according to the type of the music that is played and to compensate for the room characteristics and the speakers’ frequency characteristics. The graphic equalizer effect is only applied to the left and right front channels. This panel is always shown when no DSP sound field program is selected. When a DSP sound field program is selected, selecting the EQUALIZER tab at the bottom of the Main Panel will show this panel. 1 1 2 3 4 4 ADVANCED OPERATION 3 2 Preset patterns Five patterns of frequency characteristics have been preset for different types of music, such as “ROCK” and “POPS”. Click a button to select the effect that suits the music type. Storing and calling user’s patterns You can store and call up to two patterns of frequency characteristics you specify. FLAT This makes the frequency response curves flat. Graphic equalizer The 7-band equalizer allows you to set your desired frequency response curves. By dragging the indicator for each frequency band, you can adjust the frequencies within the range of +6 to –6 dB. English E-25 ADVANCED OPERATION Operating the built-in FM tuner With the Application Software, you can operate the tuner more easily than on the front panel or the remote control, including additional functions available only in the Application Software for example storing stations automatically and assigning names to preset stations. Click the button for calling the tuner panel at the right upper part of the Main Panel. The following screen appears. 1 1 2 3 4 5 2 6 3 4 7 8 5 6 7 8 Switching the reception mode This button toggles the reception mode between FM auto stereo and FM monaural. Station display The frequency of the currently received station or the name of the preset station is shown here. Manual tuning / (down/up) buttons Press to select higher frequencies and to select lower frequencies. TITLE This button toggles the display mode of the preset station list between frequencies and names. CLOSE This button closes the tuner panel. ADD This button is used for adding or changing preset stations. PRESET EDIT This button opens the “Tuner Preset Edit” panel. Preset station list This list shows all the preset stations by their frequencies or names. Storing stations (Tuner Preset Edit) Click the PRESET EDIT button in the left lower part of the tuner panel. The following screen opens and allows you to edit the presets. 1 2 1 3 3 2 4 E-26 4 “Automatic store” Click the “Start” button, and receivable stations are stored in sequence automatically. “Preset station titles” You can assign a name consisting of up to eight characters to each preset station. The names are shown in the preset station list in the tuner panel. “Manual store” You can store the desired stations one by one. Click the “Start” button, and all of the receivable stations are searched. You can select only the desired stations and store them onto the desired preset groups and numbers. “Close” Click this button to close the current “Tuner Preset Edit” panel and return to the tuner panel. ADVANCED OPERATION Setting adjustment on the Setup panel When you click SETUP of the Main Panel, the Setup panel appears, allowing you to perform the following settings. Edit Names of Input Sources You can assign a name consisting up to seven characters to each input source. For example, if a tape deck is connected to the AUX 1 terminals, you can change the name, AUX 1, to TAPE. As this name change information is sent to the main unit, the display on the main unit changes simultaneously. Volume Settings USB Mix When USB Mix is on, even if signals received at input terminal(s) other than the USB terminal when it is selected, you can mix the input signals from that selection with the signals from the computer via the USB connection and play the mixed signals. For example, while you are listening to music from the tape deck connected to AUX 1, mail arrival beeps and warning beeps are also available. Clicking the check box to enter the check mark in the box will turn on the USB Mix. This status allows you to adjust the volume level of the signals from the USB connection. (As this adjusts the volume balance between the selected input signals and the input signals from the USB connection, it does not affect the volume when USB is selected by the input selector keys.) Clicking the check box to delete the check mark will turn off the USB Mix. In this status, the signals from the USB connection can be played only when USB is selected by the input selector keys. Maximum Volume Setting When adjusting the volume in the Application Software, you may inadvertently turn up the volume too high. To avoid this, you can use this function to set a maximum volume for the Application Software. Digital Volume Setting This allows you to digitally turn up and down the volume in the DSP. Take care not to turn up the volume when the level of the digital input signal is high as it may cause sound distortion due to digital processing. If sound distortion occurs, turn down the volume. Skin Selection This allows you to select the skin (the design of the background picture of the Application Software) from several preset patterns. Note This feature is not available when using a Macintosh computer. Speaker Settings This allows you to select the speakers (center, surround and subwoofer) to use or not to use. Also, you can select the size (small or large) of the speakers to use. Make this setting correctly to maximize the performance of your speaker system. Setting Remote Control Custom keys This allows you to store a set of commands (input selector, sound field program, volume setting, etc.) to each of the A, B and C keys on the remote control. After storing, simply pressing each key will execute the stored command. About This Application This gives you information about the version of this Application Software. Note The screen design, functions, etc. are subject to change due to software upgrades. For details, refer to the Online Help of the Application Software. English Note It may happen that the volume is fixed to “0” when digital signals are inputted and the sound field effect is off (THROUGH). This allows you to select the number of channels for sending playback signals via the USB connection from two, four, and six channels. (Note that you cannot record signals from the USB connection on the computer when six channels are selected.) ADVANCED OPERATION Note The sound field programs have no effect on USB-mixed signals. (Sound is in normal stereo.) USB Multi-Channel Setting (for Windows only) E-27 APPENDIX APPENDIX Troubleshooting Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service center. Cause Problem Remedy The unit cannot be turned on though the power switch is pressed. The power cord is not plugged in or is not completely inserted. Firmly plug in the power cord. No sound. This unit is in the standby mode. Turn on this unit by pressing the power switch on the front panel or the POWER key on the remote control. Incorrect output cord connections. Connect the cords properly. If the problem persists, the cords may be defective. The muting function of this unit is on. Turn off the muting by pressing the MUTE key. Headphones are connected to the headphone jack of this unit. Disconnect the headphones from the headphone jack to output sound from the speakers. The volume is set to minimum. Increase the volume. The playback source is not selected by the input selector keys. Select the playback source using the input selector keys. When PC is selected as the input source, check that the USB, digital or analog input is correctly selected. The power of the equipment selected as the input source is off. Turn on the equipment. The output level of the surround speakers is set to minimum. Increase the output level of the surround speakers by using the test tone. (Refer to page 19 on how to adjust the speaker output levels.) The DSP is off. Turn on the DSP and select an appropriate sound field program. Under “Speaker Settings” in the SETUP panel of the Application, the check box “Use the surround speakers” is not checked. Check the check box “Use the surround speakers”. The output level of the center speaker is set to minimum. Increase the output level of the center speaker by using the test tone. (Refer to page 19 on how to adjust the speaker output level.) The DSP is off, or a Hi-Fi DSP program is selected. Turn on the DSP and select a CINEMA DSP program. Under “Speaker Settings” in the SETUP panel of the Application, the check box “Use the center speaker” is not checked. Check the check box “Use the center speaker”. The source does not contain center channel sound signals. Use a source which contains center channesound signals. No sound field effect. The DSP is off. Turn on the DSP. No effect of Dolby Digital or DTS though the sound field program “NORMAL” is selected. The playback source is encoded with neither Dolby Digital nor DTS. Use a source encoded with Dolby Digital or DTS. No sound from the surround speakers No sound from the center speaker E-28 APPENDIX Problem Cause What to Do When making a recording from an audio CD to an MD, CD-R, etc., all tracks are recorded as one track. A DSP sound field program is selected or the built-in graphic equalizer is used. Turn off the DSP and the graphic equalizer. Program sources on an MD, CD-R, etc. which is a copy of an audio CD, cannot be recorded on the computer via the USB connection. You cannot make a recording from a CD-R, MD, etc. which is a copy of an audio CD, to another CD-R, MD, etc. via the USB connection or the digital terminal connection. Record the signals of such an MD, CD-R, etc. on the computer by sending the signals via an analog connection. Signals inputted to your computer via the USB connection cannot be recorded on the computer. Incorrect setting of the recording device on the computer. Correctly set the recording device on the computer. [Refer to “Recording on computer (via the USB connection”) on page 13.] Different sounds are heard together. Sound from the computer via the USB connection may be mixed with sound from other sources because the “USB Mix” setting is set to “ON” with the Application Software. Set the “USB Mix” setting to “OFF” if you do not want to hear mixed sounds. Using this unit affects TV reception or the performance of other equipment. The equipment may be too close to this unit. Move the equipment away from this unit. Left and right volume levels are different. The level balance is not set to center on the “Balance” setting on the VIRTUAL panel in the Application Software. Set the level balance to center. The remote control does not work. The batteries of the remote control are weak. Replace the batteries with new ones. The remote control does not function properly. Wrong distance or angle. The remote control will function from a maximum range of 6 meters and no more than 30 degrees off-axis from the front panel. Direct sunlight or strong light (of an inverter type fluorescent lamp etc.) is striking the remote control sensor of the main unit. Reposition the main unit. When installing or using the Application Software Problem Application does not start. What to Do This unit and the computer is not connected with the USB cable. Connect this unit and the computer with the USB cable. The power cord is not plugged in or is not completely inserted. Firmly plug in the power cord. The USB cable is not firmly connected between this unit and the computer. Disconnect the USB cable, and then connect it firmly again. The power cord is not plugged in or is not completely inserted. Firmly plug in the power cord. APPENDIX The driver software cannot be installed successfully. Cause English E-29 APPENDIX When using the built-in FM tuner Cause Problem Crackling noise from time to time. Interference from the starting motor of a nearby car. What to Do Position the FM antenna as high and as far away from nearby roads as possible. Use a coaxial cable for connecting the antenna. Interference from the thermostats of a nearby electric appliance. Install a noise canceller on such an appliance. Noise increases when receiving a stereo broadcast, or the reception mode changes from stereo to monaural unexpectedly. Because of the characteristics of FM broadcasts, this is limited to cases where the transmitter is far away or the antenna signal is weak. Check the antenna connections. A desired station cannot be received by the auto tuning method. Because of the characteristics of FM broadcasts, this is limited to cases where the transmitter is far away or the antenna signal is weak. Install a multi-element type FM antenna if possible. Weak antenna signal. Install an antenna suitable for the electric field strength of your area. Not tuned correctly. Retune. There is distortion or clear reception cannot be obtained even when using a good quality FM antenna. There is multipath interference. Change the position of the antenna. Preset stations cannot be selected. The preset memory has been erased. Store the stations again. Stereo broadcasts are noisy and the ST indicator flashes. Tune in to the station manually. Depending on some computer hardware or operating systems, all functions of this unit cannot be used.You can refer to the following Yamaha website for details and related information. http://www.yamaha.co.jp/audio/ Memory back-up The memory back-up circuit prevents the setting of the input selector, the sound field program, the preset memory of the tuner from being lost even if the AC power cord is disconnected from the AC outlet or the power is cut due to a temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. In that case, you must make the necessary settings, and store the FM stations in memory again. E-30 APPENDIX Specifications Minimum RMS Output Power per Channel 12W 5 (20 Hz–20 kHz, 4Ω, 1% THD) Residual Noise (IHF-A Network) –66 dB or less (SP Output, L/R) 14W 5 (1 kHz, 4Ω, 10% THD) Tuning Range [U.S.A. and Canada models] 87.5 to 107.9 MHz [Europe, U.K. and Australia models] 87.5 to 108.0 MHz Maximum Power Input Sensitivity/Input Impedance PC IN, AUX1 IN, AUX2 IN (ANALOG) Maximum Input Signal PC, AUX1, AUX2 Output Level/Output Impedance REC OUT SUBWOOFER OUTPUT 150 mV/35 kΩ Usable Sensitivity MONO 6 dBµ 2.1V or more (1 kHz) 150 mV/2.0 kΩ 1.0V/1.7 kΩ (50 Hz) Power Supply [U.S.A. and Canada models] [Europe and U.K. models] [Australia model] Headphone Jack Output Level/Output Impedance ANALOG PC IN, etc. 320 mV/61Ω (1 kHz, 150 mV) Power Consumption Frequency Response USB, DIGITAL IN (PC, AUX1) to SP Output 20 Hz–20 kHz (2.0 dB) Dimensions (W H D) Weight Total Harmonic Distortion (1 kHz, 20 kLPF) USB, DIGITAL IN (PC, AUX1) to SP Output 0.2% or less (5V/4Ω) Signal-to-Noise Ratio USB to SP Output 85 dB or more PC IN, AUX1 IN (DIGITAL) to SP Output 85 dB or more Accessories AC 120V, 60 Hz AC 230V, 50 Hz AC 240V, 50 Hz 90W (In the standby mode: 5W or less) 120 294 355 mm (4-3/4” 11-9/16” 14”) 5.5 kg (12 lbs. 2 oz.) CD-ROM (Windows/Macintosh-hybrid) USB cable Remote control Battery2 Indoor FM antenna Specifications are subject to change without notice. APPENDIX English E-31 YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed in Malaysia V688970 UCA PERSONAL RECEIVER RP-U200 PC AUX1 AUX2 TUNER POWER VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST PC AUX1 VOL AUX2 TUNER MEMORY DSP PRESET MANUAL CHURCH HALL JAZZ GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C MUTE P-SET VOLUME SET UP MANUAL MANUEL DE CONFIGURATION The owner’s manual for this model consists of two volumes, “SET UP MANUAL” and “OPERATION MANUAL”. Le manuel d'utilisation pour ce modèle se compose de deux volumes, le “MANUEL DE CONFIGURATION” et le “MANUEL D’UTILISATION”. * This manual uses terms utilized by the English operating system as shown on the computer monitor. If the operating system you are using is in another language, please replace the English terms with the terms used in your computer’s operating system. * Ce manuel utilise des termes employés par les systèmes d’exploitation en langue anglaise tels qu’ils apparaîssent sur le moniteur d’un ordinateur. Si votre système d’exploitation utilise une autre langue, veuillez remplacer la terminologie anglaise par celle qu’il utilise. CONTENTS Unpacking ........................................... Battery installation ............................. Battery replacement ........................... Remote control operation range ....... 2 2 2 2 Terminals and their functions ........... Connecting your computer ................ Connecting audio equipment ............ Connecting speakers ......................... Connecting an FM antenna ................ Plugging in this unit ........................... 3 4 5 6 9 9 Preparations before installation ...... 10 System requirements ....................... 10 Installing the software ...................... 11 Microsoft Windows 98/98SE or Windows Me ............................................... 11 Microsoft Windows 2000 Professional ......... 14 Macintosh computer ...................................... 17 INSTALLING USB DRIVER AND APPLICATION SOFTWARE INSTALLING USB DRIVER AND APPLICATION SOFTWARE CONNECTIONS CONNECTIONS GETTING STARTED GETTING STARTED English E-1 GETTING STARTED Unpacking Battery installation After unpacking, check that the following items are supplied. Since the remote control will be used for many of this unit’s control operations, you should begin by installing the ● Remote control supplied batteries. ● Batteries (AA, R6, UM-3 type) POWER 1 3 PC 2 AUX1 AUX2 TUNER MEMORY PRESET MANUAL HALL JAZZ CHURCH GAME MOVIE LIVE / DTS SURROUND TEST ON/OFF A B C MUTE ● USB cable 1 Turn the remote control over and remove the battery compartment cover by sliding it in the direction of the arrow. 2 Insert the batteries (AA, R6, UM-3 type) according to the polarity markings on the inside of the battery compartment. 3 Close the battery compartment cover. VOLUME ● Indoor FM antenna Battery replacement (U.S.A. and Canada models) (U.K., Europe and Australia models) If you notice that the remote control must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes ● Use AA, R6, UM-3 batteries. ● Be sure the polarities are correct. (See the illustration inside the battery compartment.) ● Remove the batteries if the remote control is not to be used for an extended period of time. ● If the batteries leak, dispose of them immediately. Avoid touching the leaked material and avoid contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. ● CD-ROM The CD-ROM contains the Application Software and online help for controlling this unit from your computer. Remote control operation range PC AUX1 AUX2 TUNER VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST Remote control sensor VOL DSP P-SET Within approximately 6 m (19.7 feet) 30° E-2 30° Notes ● The area between the remote control and the main unit must be clear of large obstacles. ● Do not expose the remote control sensor to strong lighting, in particular, an inverter type fluorescent lamp; otherwise, the remote control may not work properly. If necessary, position the main unit away from direct lighting. CONNECTIONS CONNECTIONS Never plug in this unit and other equipment until all connections are completed. 1. Make connections between this unit and other components by following the procedure below. 2. After all connections are finished, check that the connection cables are correctly connected. 3. After all connections are completed, plug in this unit and other equipment. Note Also, refer to the owner’s manual for other equipment in the system. Use commercially available connection cables (except the supplied USB cable). The color of this unit’s inputs/outputs and pin-plug connection cables to be used for connecting to them are as follows: Analog audio signals for the left channel (stereo) L L Red Analog audio signals for the right channel (stereo) R R Black Analog audio signals (monaural) Digital audio signals (coaxial) CONNECTIONS White Terminals and their functions 1 FM antenna connector This connector is used to connect an FM antenna. 2 SUBWOOFER OUTPUT This connector can be connected to an optional subwoofer, such as the Yamaha YST-SW45, for enhanced bass performance. ANALOG R L PC IN 1 ANTENNA AUX 1 IN FM ANT 75Ω UNBAL. AUX 2 IN SUB WOOFER 4 REC OUT OUTPUT 2 R SPEAKERS L 5 These connectors are used to connect to the analog outputs of a PC sound card, CD player, MD recorder, tape deck, etc. + USB L FRONT COAX IN R 3 6 PC 4Ω MIN. /SPEAKER – + AUX 1 OPT IN L REAR 5 REC OUT These connectors are used to connect to the analog inputs of an MD recorder or tape deck. OPT IN CENTER Up to five speakers, such as the Yamaha NS-U40P speaker system can be connected to the FRONT L, R, CENTER, REAR L and R terminals. Use speakers whose impedance is 4Ω or more. 4 ANALOG inputs DIGITAL – 3 SPEAKERS outputs OPT OUT R (U.S.A. model) 7 6 PC inputs & output (DIGITAL) USB: If your computer has a USB port, connect it to this unit, using the supplied USB cable, for remote control of this unit from your computer. PC COAX IN/OPT IN: These coaxial and optical connectors are used to connect to the digital outputs of a PC sound card, DVD-Video decoder board, etc. 7 Optical input & output (DIGITAL) AUX 1 OPT IN: This connector is used to connect to an optical output of a CD player, MD recorder, etc. OPT OUT: This connector is used to connect to an optical input of an MD recorder, a DAT deck, etc. E-3 CONNECTIONS Connecting your computer Audio from your computer can be fed to this unit using any of the following connectors: USB, DIGITAL PC COAX IN, DIGITAL PC OPT IN, or ANALOG PC IN. If you use all of these connectors for connection, you can select the connector(s) to use on this unit’s front panel or the remote control. Connecting to the USB port (1) Connecting to digital inputs (3) If your computer has a USB port, connect it to this unit’s USB terminal using the supplied USB cable, as shown below. A single USB connection is all that’s required to listen to audio from your computer on this unit, feed audio from an external source connected to this unit to your computer, and control this unit remotely from your computer, using the supplied Application Software. If your computer doesn’t have a USB port, you can still connect it to this unit using the analog or digital input, but in this case you cannot use this unit’s Application Software. To play DVD-Video discs encoded with Dolby Digital or DTS, your computer must have a DVD-ROM drive and DVD-Video decoder board, which should be connected to this unit via the DIGITAL PC COAX IN or DIGITAL PC OPT IN. Use a commercially available pin-plug cable for connecting to the DIGITAL PC COAX IN, and use a commercially available optical fiber cable for connecting to the DIGITAL PC OPT IN. Note The DIGITAL PC OPT IN has priority over the DIGITAL PC COAX IN, so if you connect to both inputs, the signal received at the DIGITAL PC OPT IN is used. Note Connect the USB cable when installing the USB driver software on your computer. Refer to the section “INSTALLING USB DRIVER AND APPLICATION SOFTWARE”. Protective Caps When connecting to an optical connector, remove its protective cap first. When an optical connector is not being used, replace its cap to prevent dust entering the connector. Connecting to analog inputs (2) Connect the analog audio outputs on your computer or a PC sound card to this unit’s ANALOG PC IN. Use a commercially available pin-plug cable for connection, and be careful not to mix up the left and right connections. ANALOG R L : Indicates the direction of signals. PC IN ANTENNA AUX 1 IN FM ANT 75Ω UNBAL. SUB WOOFER L AUX 2 IN R 2 REC OUT OUTPUT R – L R L DIGITAL SPEAKERS LINE OUT 1 USB + USB L FRONT DIGITAL OUT (coaxial) COAX IN R PC OPT IN CENTER 4Ω MIN. /SPEAKER – + AUX 1 OPT IN L REAR R E-4 (U.S.A. model) 3 OPT OUT 3 DIGITAL OUT (optical) CONNECTIONS Connecting audio equipment The following illustrations show how to connect a CD player, MD recorder, etc. using both analog and digital connections. However, it’s not necessary to make both connections. Audio connections Digital connections ● Be careful not to mix up the left and right connections. If you wish to record digital sound signals inputted to this unit, connect the optical digital input of an MD recorder or a DAT deck to this unit’s DIGITAL OPT OUT. ● If you wish to record analog sound signals inputted to this unit, connect the analog inputs of a tape deck or MD recorder to this unit’s REC OUT. CONNECTIONS DIGITAL OUT (optical) CD player LINE OUT R CD player L SPEAKERS DIGITAL – + USB L FRONT COAX IN R ANALOG PC R L R PC IN ANTENNA OPT IN CENTER L 4Ω MIN. /SPEAKER – AUX 1 IN + AUX 1 OPT IN L AUX 2 IN FM ANT 75Ω UNBAL. L R SUB WOOFER REAR OPT OUT R REC OUT OUTPUT R L L (U.S.A. model) DIGITAL SPEAKERS – + DIGITAL IN (optical) R USB L MD recorder FRONT (U.S.A. model) LINE IN (REC) R L Tape deck or MD recorder R L LINE OUT (PLAY) Notes ● Connecting a turntable A turntable cannot be connected to this unit directly. Use a commercially available phono preamp to connect a turntable to this unit, or connect a turntable incorporated with a phono equalizer amplifier. ● The REC OUT and DIGITAL OPT OUT can be used at the same time since they output signals independently. Notes ● When playing an ordinary CD on this unit following playback of a CD or an LD encoded with DTS, some operations, such as resetting the input selector keys, may be required. ● If some data processing (e.g. volume level changes) is applied to DTS-encoded signals on the CD, DVD or LD player, this unit will not recognize the signals as DTS-encoded signals. Because of this, this unit cannot reproduce a DTS-encoded source played on such a player even if it is connected to this unit with a digital connection. ● When an error occurs in the player’s digital output data during playback of an LD or CD encoded with DTS, playback may be disrupted. If this occurs, stop playback and repower the player. ● When digital sound signals from the computer are played, errors in WAV signals, etc. may occur resulting in noise or a playback failure. E-5 CONNECTIONS Connecting speakers To reproduce multi-channel surround sounds with this unit, connect five speakers (Yamaha NS-U40P, etc.) to this unit as follows: a pair of front speakers to the FRONT L and R terminals, a center speaker to the CENTER terminal, and a pair of surround speakers to the REAR L and R terminals. When using only one pair of speakers, connect one speaker to the FRONT L terminal, and the other to the FRONT R terminal. * Notes ● Use speakers which do not have a built-in amplifier. ● Use speakers whose impedance is 4Ω or more. ● Connect the left speaker to the left speaker connector on this unit and the right speaker to the right speaker connector. ● Make sure that the + and – polarity markings of the speaker cables are observed and set correctly. If these cables are reversed, the sound will be unnatural and lack bass. When the supplied Application Software is installed on the computer connected to this unit, the Application enables you to make “Speaker Settings”. In the settings, you can select the speakers to use and not to use, and also set the sizes of the speakers to use. Refer to page 27 of the separate “OPERATION MANUAL” for details. ANALOG R Front speaker (L) L Front speaker (R) PC IN ANTENNA AUX 1 IN AUX 2 IN FM ANT 75Ω UNBAL. SUB WOOFER REC OUT OUTPUT R Center speaker L DIGITAL SPEAKERS – + USB L FRONT COAX IN R PC OPT IN CENTER 4Ω MIN. /SPEAKER – Surround speaker (L) + AUX 1 OPT IN Surround speaker (R) L REAR OPT OUT R (U.S.A. model) E-6 CONNECTIONS Speaker Cables Strip 10 mm of insulation off the end of each speaker cable, and then twist the bare wires to prevent lose strands, which can cause short circuits. How to connect: 1 Press and hold the speaker connector levers. 2 Insert the bare ends of the speaker cables into the terminal holes. 10 mm 3 Then release the levers. * Try pulling gently on each cable to make sure that it is secure. ➂ ➀ CONNECTIONS ➁ Adding a subwoofer It is recommended to connect a subwoofer to this unit to enhance the bass performance of your system and reproduce surround sounds of Dolby Digital, DTS and CINEMA DSP effectively. Notes ● The SUBWOOFER OUTPUT is a line-level output. Use a subwoofer which has its own built-in power amplifier, such as the Yamaha YST-SW45. ● If no sound is reprodced from the subwoofer, check the “Speaker Settings” in the Application Software. Refer to page 27 of the separate “OPERATION MANUAL” for details. STANDBY/ON HIGH CUT 50Hz 150Hz L PC IN ANTENNA AUX 1 IN AUX 2 IN FM ANT 75Ω UNBAL. VOLUME 0 ANALOG R 10 SUPERWOOFER SYSTEM YST-SW45 SUB WOOFER LINE IN REC OUT OUTPUT R L DIGITAL SPEAKERS – + L USB FRONT Subwoofer (U.S.A. model) E-7 CONNECTIONS Setting up the speakers The role of the respective speakers In a 5.1-channel surround system, the front speakers are used for reproducing main channel sound (normal stereo sound) and effect sound. The surround speakers are used for surround and effect sounds, and the center speaker is for center channel sound (dialog, etc.). (The center speaker can be omitted if you prefer, however, the best result is obtained with a full five speaker system.) The subwoofer is used for reproducing low frequency sounds from the front, center and surround channels. The subwoofer also reproduces sounds of the subwoofer channel when a DTS or Dolby Digital encoded source is played. Recommended speaker placement Before making connections, place all speakers in their respective positions. The positioning of the speakers is important because it controls the overall sound quality of this system. Place the speakers depending on your listening position by following the instructions below. Front speakers: On both sides of and at approximately the same height as your computer monitor. The distances from each speaker to the listening position must be the same. Surround speakers: Behind your listening position or on both sides of the listening room. According as the condition of your listening room, place the surround speakers on the floor or the shelf, or mount them on the wall. Center speaker: Precisely between the front speakers. * The center speaker can be mounted on the monitor if it is a magnetically shielded type. Subwoofer: On the floor. Place the subwoofer on the position where you can get the optimum bass performance from the listening position. Note Use magnetically-shielded speakers and subwoofer. If the monitor picture is disturbed even by using the magneticallyshielded speakers, set the speakers apart from the monitor. A set up example Center speaker Front speaker (left) Front speaker (right) This unit Surround speaker (right) Subwoofer E-8 Surround speaker (left) CONNECTIONS Connecting an FM antenna Connect an FM antenna to the FM ANT terminal of this unit by following the figure and procedures below. Indoor FM antenna (supplied) Outdoor FM antenna ANALOG R L PC IN AUX 1 IN F-type plug adaptor AUX 2 IN FM ANT 75Ω UNBAL. SUB WOOFER REC OUT OUTPUT R — L DIGITAL SPEAKERS + L (U.S.A. model) CONNECTIONS ANTENNA 75Ω coaxial cable USB FRONT It is recommended to use an outdoor FM antenna for good reception. Depending the area, good reception may not be obtained because it is far from FM radio stations or obstructed by tall buildings, mountains, and so on. Select a type of antenna suitable for your area. Also, to minimize the effects of automobile ignition noise, locate the antenna as far away from heavy traffic as possible. ● Use the supplied indoor FM antenna only in areas with exceptionally good reception. * Set the indoor FM antenna as far away from the computer and the monitor as possible, and set it to a position where the best reception is obtained. ● For connecting an outdoor FM antenna Use a 75Ω coaxial cable for connecting the antenna. If the antenna is located far from this unit, the use of 5C2V cable is recommended to handle the weak radio signal. * If you connect an outdoor FM antenna to this unit, do not connect the indoor FM antenna to this unit. (U.S.A. model) Insert the antenna connector securely. Plugging in this unit After completing all connections, plug the AC power cord into a household AC outlet. AC outlet Note Unplug the AC power cord from the AC outlet if this unit is not to be used for a long period of time. (U.S.A. model) E-9 INSTALLING USB DRIVER AND APPLICATION SOFTWARE INSTALLING USB DRIVER AND APPLICATION SOFTWARE When connecting this unit and your computer with the USB cable and controlling this unit from the computer, you must install the following software on your computer. ◆ USB driver software: Necessary for this unit to communicate with your computer .......... Use the software originally supplied with the OS (Operating System) running on your computer ◆ Application Software: Used to control this unit from a computer .......... Download from the supplied CD-ROM ◆ Online help : Instructions for using the Application ......... Access from the supplied CD-ROM This section explains how to install the software. The installation method differs from the OS running on your computer. Refer to the instructions suitable for your OS below. Preparations before installation ● Make sure that the USB cable is not connected to this unit and that your computer is not activated. ● Make sure that your computer meets the system requirements listed below. If your computer does not meet the system requirements, you can use the computer as an input source by connecting it to the analog or digital input(s) of this unit. In that case, however, the supplied Application Software cannot be used. ● You may be requested to insert your OS’s CD-ROM during the installation, so please have it ready before commencing. ● The installing method may differ from the instructions below depending on the operating environment of your computer. In such a case, follow the instructions shown on the monitor. If you still have any question, inquire at the manufacturer of your computer or a computer dealer. System requirements Your computer must meet the following system requirements to use the supplied Application Software. Microsoft Windows 98/98SE, Windows Me or Windows 2000 Professional Operating System Microsoft Windows 98/98SE, Windows Me or Windows 2000 Professional Computer A computer with a USB port as a standard equipment and preinstalled with the above OS. Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries. E-10 Macintosh Operating System Mac OS 9.04, 9.1 or greater (except for the OS 9.04 preinstalled on Macintosh computers put on the market in June of 2000 or before) Computer Macintosh computer preinstalled with the above OS and equipped with a USB port as a standard equipment Macintosh is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. INSTALLING USB DRIVER AND APPLICATION SOFTWARE Installing the software Microsoft Windows 98/98SE or Windows Me 䡵 Installing and checking the USB driver 1 Turn on your computer and, if it’s not running already, start Windows 98/98SE or Windows Me. 2 Plug the AC power cord of this unit into the AC outlet. 9 Click the “+” symbol next to “Human Interface Devices”, and make sure that “HID-compliant consumer control device” and “USB Human Interface Device” appear in the list, as shown. This unit can be on or in standby mode when installing the driver. 3 Connect this unit to a USB port on the computer using the supplied USB cable. INSTALLING USB DRIVER AND APPLICATION SOFTWARE Windows automatically detects this unit and installs the necessary driver software. Make operations as indicated in the dialog box. You may be requested to insert your Windows OS CD-ROM. * The installation may take a longer time depending on the system environment. After the installation dialog box disappears, wait several minutes. * The screen image is for Windows 98SE. 10 Check that the USB driver has been installed successfully by following the procedure below. 4 Click the “+” symbol next to “Universal Serial Bus controllers” and make sure that “USB Composite Device” appears in the list, as shown. Click the Windows “Start” button and select “Settings”, and then “Control Panel”. The Control Panel window appears. 5 Double-click the “System” icon. The System Properties window appears. 6 Click the “Device Manager” tab. The Device Manager window appears. 7 Click the “View devices by type” option button. 8 Click the “+” symbol next to “Sound, video and game controllers,” and make sure that “USB Audio Device” appears in the list, as shown. Notes ● The device list on your computer may differ to that shown here. ● If “!” or “?” is shown at the head of the device name, check the followings: * The USB cable is firmly connected. * The AC power cord of this unit is plugged into an AC outlet. ● If the driver has not been successfully installed, disconnect the USB cable and connect it again. Then try to install the driver again. If installation still fails, restart Windows and try again. English * The screen image is for Windows 98SE. * When using Windows Me, “?” may be shown at the head of “USB Copmposite Device” in green. This means the USB driver has been installed with the Generic ID supplied with the operating system. (This is not an error message.) * The screen image is for Windows 98SE. E-11 INSTALLING USB DRIVER AND APPLICATION SOFTWARE Make the following settings on your computer after the installation of the driver is finished. Setting of Audio and Audio CD [Windows 98/98SE only] * * Checking sound output and adjusting volume [Windows 98/98SE and Windows Me] Terminate all the activated applications. When using Windows 98SE, restart Windows, first. PC 1 2 AUX2 TUNER VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST Double-click the “Multimedia” icon. * Usually, this setting is automatically made. Volume control * If “USB Audio Device” does not appear, restart Windows. Power switch Click the “CD Music” tab and select the CD-ROM drive for playing audio CDs. 5 Click the check box of “Enable digital CD audio for this CD-ROM device” to enter the check mark. 1 6 Click “OK” and close the “Multimedia” setting panel. 7 Restart Windows. 2 b) Adjust the volume by dragging the “Volume” slider. Set the slider between the center and max. positions. Checking the Audio setting [Windows Me only] 2 Double-click the “Sounds and Multimedia” icon. 3 Click the “Audio” tab and select “USB Audio Device” at “Preferred device” of “Sound Playback”. * Usually, this setting is automatically made. * If “USB Audio Device” does not appear, restart Windows. Adjust the volume on the computer as follows. a) Double-click the speaker icon on the task tray, or select “Start”, “Programs”, “Accessories”, “Entertainment” in this order and click “Volume Control”. (The volume adjustment window appears.) Note When using two or more drives, you must make the above setting for each drive. Click the Windows Me “Start” button and select “Settings”, and then “Control Panel”. Make the following operations on the front panel of this unit. a) Press the power switch to turn on this unit. (Some messages are shown on the display.) b) Press the PC input selector key repeatedly to select USB as the input source. c) Use the volume control to adjust the volume. (Set the control to about “30”.) * It may happen that the check box cannot be clicked because some CD-ROM drives cannot be used for playing audio CDs. * Do not enter the check mark in the “Mute” check box. If entered, sound output will stop. 3 Click the Windows “Start” button and select “Settings”, and then “Control Panel”. 4 Double-click the “Sounds” (or “Sounds and Multimedia”) icon. 5 Click the “Sounds” tab. 6 Check that the sound is output normally by outputting “Default sound”, etc. from “Events” (or “Sound Events”). * E-12 P-SET Click the “Audio” tab and select “USB Audio Device” at “Preferred device” of “Playback”. 4 1 Display VOL DSP 3 PC AUX1 Click the Windows “Start” button and select “Settings”, and then “Control Panel”. If no sound is heard, restart Windows and check again. INSTALLING USB DRIVER AND APPLICATION SOFTWARE Next, install the Application Software and Online Help from the supplied CD-ROM. 䡵 Installing the Application Software * Terminate all the activated applications (including virus checkers) on the computer first. 1 This section explains how to uninstall the Application Software. 1 Terminate the Application Software and online help. 2 Click the Windows “Start” button and select “Settings”, and then “Control Panel”. Insert the CD-ROM into the CD-ROM or DVD-ROM drive. If the Windows Autorun feature is turned on, the installation start-up screen appears automatically. 2 䡵 Uninstalling the Application Software The Control Panel window appears. 3 The “Add/Remove Programs Properties” window appears. Continue with the installation as prompted. 4 If the Windows Autorun feature is not turned on Display the contents of the CD-ROM by using “My Computer” etc., and double-click on “Readme.txt.”. The installation method is described in this file. This section explains how to start the Application Software and view the online help. Click the Windows “Start” button and select “Programs”, “YAMAHA RP-U200”, “RP-U200” in this order. The Application Software starts. 2 Select “YAMAHA RP-U200 Application” in the software list. “YAMAHA RP-U200 Application” is highlighted. 5 Click the “Add/Remove Programs” button and continue as prompted. INSTALLING USB DRIVER AND APPLICATION SOFTWARE 䡵 Using the Application Software and Online Help 1 Double-click the “Add/Remove Programs” icon. To view the online help, click the Windows “Start” button and select “Programs”, “YAMAHA RPU200”, “Help” in this order. The online help, which explains how to use the Application Software, starts. Note Never disconnect the USB cable while starting up the Application Software. If disconnected, the computer may freeze. English E-13 INSTALLING USB DRIVER AND APPLICATION SOFTWARE Microsoft Windows 2000 Professional 䡵 Installing and checking the USB driver 1 Turn on your computer and, if it’s not running already, start Windows 2000 Professional, and log in with Administrator. 2 Plug the AC power cord of this unit into the AC outlet. 9 Click the “+” symbol next to “Human Interface Devices”, and make sure that “HID-compliant consumer control device” and “USB Human Interface Device” appear in the list, as shown. This unit can be on or in the standby mode when installing the driver. 3 Connect this unit to a USB port on the computer using the supplied USB cable. Windows automatically detects this unit and installs the necessary driver software. * The installation may take a longer time depending on the system environment. After the dialog box for installation disappears, wait several minutes. 10 Check that the USB driver has been installed successfully by following the procedure below. 4 Click the “+” symbol next to “Universal Serial Bus controllers” and make sure that “USB Composite Device” appears in the list, as shown. Click the Windows “Start” button and select “Settings”, and then “Control Panel”. The Control Panel window appears. 5 Double-click the “System” icon. The System Properties window appears. 6 Select the “Hardware” tab, and click the “Device Manager”. The Device Manager window appears. 7 Select the “View” tab, and click the “Devices by type” option button. 8 Click the “+” symbol next to “Sound, video and game controllers,” and make sure that “USB Audio Device” appears in the list, as shown. E-14 Notes ● The device list on your computer may differ to that shown here. ● If “!” or “?” is shown at the head of the device name, check the followings: * The USB cable is firmly connected. * The AC power cord of this unit is plugged into an AC outlet. ● If the driver has not been successfully installed, disconnect the USB cable and connect it again. Then try to install the driver again. If installation still fails, restart Windows and try again. INSTALLING USB DRIVER AND APPLICATION SOFTWARE Make the following settings on your computer after the installation of the driver is finished. Setting of Audio and Audio CD 1 Checking sound output and adjusting volume Click the Windows “Start” button and select “Settings”, and then “Control Panel”. PC PC AUX1 AUX2 TUNER 2 Double-click the “Sounds and Multimedia” icon. 3 Click the “Audio” tab and select “USB Audio Device” at “Preferred device” of “Sound Playback”. VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST Display VOL DSP P-SET * Usually, this setting is automatically made. Volume control 4 Click the “Hardware” tab and double-click the item of the DVD or CD-ROM to be used in the “Devices”. Power switch 5 Click the “Properties” tab, and click the check box of “Enable digital CD audio for this CD-ROM device” to enter the check mark. 1 6 a) Press the power switch to turn on this unit. (Some messages are shown on the display.) b) Press the PC input selector key repeatedly to select USB as the input source. c) Use the volume control to adjust the volume. (Set the control to about “30”.) Restart Windows, and log in with Administrator. Note When using two or more drives, you must make the above setting for each drive. 2 Adjust the volume on the computer as follows. a) Double-click the speaker icon on the task tray, or select “Start”, “Programs”, “Accessories”, “Entertainment” in this order and click “Volume Control”. (The volume adjustment window appears.) INSTALLING USB DRIVER AND APPLICATION SOFTWARE * It may happen that the check box cannot be clicked because some CD-ROM drives cannot be used for playing audio CDs. Make the following operations on the front panel of this unit. b) Adjust the volume by dragging the “Volume” slider. Set the slider between the center and max. position. * Do not enter the check mark in the “Mute” check box. If entered, sound output will stop. 3 Click the Windows “Start” button and select “Settings”, and then “Control Panel”. 4 Double-click the “Sounds and Multimedia” icon. 5 Click the “Sounds” tab. 6 Check that the sound is output normally by outputting “Default Beep”, etc. from “Sound Events”. * If no sound is heard, restart Windows and check again. English E-15 INSTALLING USB DRIVER AND APPLICATION SOFTWARE Next, install the Application Software and Online Help from the supplied CD-ROM. 䡵 Installing the Application Software 1 Insert the CD-ROM into the CD-ROM or DVD-ROM drive. 䡵 Uninstalling the Application Software This section explains how to uninstall the Application Software. 1 Terminate the Application Software and online help. 2 Click the Windows “Start” button and select “Settings”, and then “Control Panel”. If the Windows Autorun feature is turned on, the installation start-up screen appears automatically. 2 Continue with the installation as prompted. The Control Panel window appears. 3 Double-click the “Add/Remove Programs” icon. The “Add/Remove Programs” window appears. If the Windows Autorun feature is not turned on Display the contents of the CD-ROM by using “My Computer” etc., and double-click on “Readme.txt.”. The installation method is described in this file. 4 “YAMAHA RP-U200 Application” is highlighted. 5 䡵 Using the Application Software and Online Help This section explains how to start the Application Software and view the online help. 1 Click the Windows “Start” button and select “Programs”, “YAMAHA RP-U200”, “RP-U200” in this order. The Application Software starts. 2 To view the online help, click the Windows “Start” button and select “Programs”, “YAMAHA RPU200”, “Help” in this order. The online help, which explains how to use the Application Software, starts. Note Never disconnect the USB cable while starting up the Application Software. If disconnected, the computer may freeze. E-16 Select “YAMAHA RP-U200 Application” in the software list. Click the “Change/Remove” button and continue as prompted. INSTALLING USB DRIVER AND APPLICATION SOFTWARE Macintosh computer 䡵 Connections and setup 1 Plug the AC power cord of this unit into the AC outlet. 2 Start the Macintosh. 3 Connect this unit to a USB port on the computer using the supplied USB cable. The driver software for USB audio is automatically installed. 4 Press the power switch of this unit to turn on this unit. Some messages are shown on the display. Checking sound output and adjusting volume PC TUNER VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST Display VOL DSP P-SET Volume control INSTALLING USB DRIVER AND APPLICATION SOFTWARE PC AUX1 AUX2 Notes ● The sound output destination cannot be changed from “Choose a device for sound output” on the “Control Panels”. When using the internal speaker of the Macintosh as the sound output destination, disconnect the USB cable connecting this unit and the Macintosh. ● When using headphones with this unit connected to the USB port on the Macintosh, use the headphone jack on this unit, not the jack on the Macintosh. ● Since the Macintosh issues a start-up sound at power-on before the sound signal via the USB connection is activated, the start-up sound cannot be issued via the USB connection. To play the start-up sound via this unit, you need a separate analog connection between this unit and the Macintosh. (When USB MIX is set to “ON” from the Setup Panel of the Application Software, you can mix the start-up sound via the analog connection with the same sound via the USB connection without making any change in the input selector settings.) Power switch 1 Make the following operations on the front panel of this unit. a) Press the PC input selector key repeatedly to select USB as the input source. b) Use the volume control to adjust the volume. (Set the control to about “30”.) 2 Check that the sound is output normally by outputting “Alert Sounds”, etc. from “Sound” on the “Control Panels” on the Macintosh. 3 Adjust the volume by dragging the “Sound” tab on the “Control Panels”. Set the tab between the center and max. position. English E-17 INSTALLING USB DRIVER AND APPLICATION SOFTWARE Next, install the Application Software and Online Help from the supplied CD-ROM. 䡵 How to use the Application Software and Online Help 䡵 Installing the Application Software All operating instructions for the Application Software is available from the Online Help. To refer to the instructions, select the Online Help from the menu displayed upon activation of the Application Software. 1 Insert the CD-ROM into the CD-ROM or DVD-ROM drive. The CD-ROM includes the simple installer “RP-U200 Installer” and the installation data folder. 2 Open the folder “English”, and double-click the simple installer “RP . AP . DP Installer” to start it. Select the model name of this unit and the destination of the installation. The Application Software and Online Help are installed on the hard disk. * * Files installed by the simple installer The simple installer “RP . AP . DP Installer” copies the “RP . AP . DP Application” folder in the installation data folder to a specified location. It additionally copies the “RP . AP . DP Help” folder into the “Help” folder in the “System Folder” on the startup disk. To install the Application Software without using the simple installer, follow the instructions below. Installing the Application Software without using the simple installer “RP . AP . DP Installer”: 1 Copy the “RP-U200 Application” folder in the installation data folder to any hard disk. 2 Copy the “RP-U200 Help” folder in the installation data folder to the “Help” folder in the “System Folder” on the startup disk. You can refer to this Online Help file with Mac Help. E-18 Relationship between operation on this unit and the Application Software When an operation button or the volume control on this unit is operated with the Application Software activated, the display screen of the Application Software automatically changes to reflect the changes made on the unit. When this unit is operated as above while the display shows the screens of the Application Software data and another program, the display of the other program (for example, the playback display of QuickTime) may be partially disturbed as the screen of the Application Software responds to the operation on this unit. To avoid this, operate this unit without activating the Application Software. YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed in Malaysia V689000