Samsung WA45M7050AW/A4-00 El manual del propietario

Marca: Samsung

Modelo: WA45M7050AW/A4-00

Categoría: Lavadoras

Tipo: El manual del propietario

Este manual también es adecuado para

Washing Machine

user manual

WA50M7450A*

WA45M7050A*

imagine the possibilities

Thank you for purchasing this Samsung product.

WA7000M_EN.indd 1WA7000M_EN.indd 1 2/3/2017 11:13:18 AM2/3/2017 11:13:18 AM

English - 2

contents

INSTALLING YOUR WASHER

10 Unpacking your washer

10 Overview of your washer

11 Basic location requirements

11 Electrical

11 Grounding

11 Water

12 Drain facility

12 Flooring

12 Location considerations

12 Alcove or closet installation

13 Required dimensions for Installation

14 Important note to installer

14 Installation ﬂ ow chart

OPERATING INSTRUCTIONS

18 Loading your washer

18 Getting started

WASHING A LOAD OF LAUNDRY

19 Overview of the control panel

21 Child Lock [

]

22 Sound

22 Garment

22 Delay End

22 Pre Soak

23 Mist Shower

23 Smart Care

24 Washing clothes using the cycle selector

24 ATC (Auto Temperature Control)

25 Detergent use

25 Features

MAINTAINING YOUR WASHER

28 Cleaning the exterior

28 Cleaning the interior

28 Storing your washer

28 Preserving the top cover and the front frame

28 Cleaning mesh ﬁ lter

29 Cleaning the dispensers

30 Self Clean

TROUBLESHOOTING

31 Check these solutions if your washer…

33 Information codes

APPENDIX

35 Fabric care chart

36 Cycle chart

38 Helping the environment

38 Declaration of conformity

38 Speciﬁ cation

WA7000M_EN.indd Sec6:2WA7000M_EN.indd Sec6:2 2/3/2017 11:13:22 AM2/3/2017 11:13:22 AM

English - 3

safety information

Congratulations on your new Samsung Washer. This manual contains important

information on the installation, use, and care of your appliance. Please take time

to read this manual to take full advantage of your washer’s many beneﬁ ts and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, and operating your washer.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury

or death.

To reduce the risk of ﬁ re, explosion, electric shock, or personal injury

when using your washer, follow these basic safety precautions:

CAUTION

Hazards or unsafe practices that may result in minor personal injury or

property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning icons are here to prevent injury to you and others.

Please heed them explicitly.

After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

SAVE THESE INSTRUCTIONS

WA7000M_EN.indd Sec1:3WA7000M_EN.indd Sec1:3 2/3/2017 11:13:22 AM2/3/2017 11:13:22 AM

English - 4

SAVE THESE INSTRUCTIONS

WARNING

State of California Proposition 65 Warning (US only)

This product contains chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm.

IMPORTANT SAFETY PRECAUTIONS

To reduce the risk of ﬁ re, electric shock, or injury to persons when using your

appliance, follow basic precautions, including the following:

1. Read all instructions before using the appliance.

2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked

in, or spotted with gasoline, dry-cleaning solvents, other ﬂ ammable or explosive

substances as they give o vapors that could ignite or explode.

3. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

4. Before the appliance is removed from service or discarded, remove the lid of the

washing or drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to the weather.

7. Do not tamper with the controls.

8. Do not repair or replace any part of the appliance or attempt any servicing unless it is

speciﬁ cally recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

9. Do not add gasoline, dry-cleaning solvents, or other ﬂ ammable or explosive substances

to the wash water. These substances give o vapors that could ignite or explode.

10. Under certain conditions, hydrogen gas may be produced in a hot water system that

has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the

hot water system has not been used for 2 weeks or more, before using a washer or

combination washer-dryer, turn on all hot water faucets and let the water ﬂ ow from

each for several minutes. This will release any accumulated hydrogen gas. As the gas is

ﬂ ammable, do not smoke or use an open ﬂ ame during this time.

safety information

WARNING

WA7000M_EN.indd Sec1:4WA7000M_EN.indd Sec1:4 2/3/2017 11:13:22 AM2/3/2017 11:13:22 AM

English - 5

CRITICAL INSTALLATION WARNINGS

Plug the power cord into an AC 120 V / 60 Hz/wall socket rated at 15 amps or higher. Use

the socket for this appliance only. In addition, do not use an extension cord.

- Sharing a wall socket with other appliances, using a power strip, or extending the power

cord may result in electric shock or ﬁ re.

- Do not use an electric transformer. It may result in electric shock or ﬁ re.

- Ensure that the power voltage, frequency, and current match the product’s

speciﬁ cations. Failing to do so may result in electric shock or ﬁ re.

Have this appliance installed by a qualiﬁ ed technician or service company.

- Failing to do so may result in electric shock, ﬁ re, an explosion, problems with the

product, or injury.

Remove all foreign substances such as dust or water from the power plug terminals and

contact points using a dry cloth on a regular basis.

- Unplug the power plug and clean it with a dry cloth.

- Failing to do so may result in electric shock or ﬁ re.

Plug the power plug into the wall socket in the right direction so that the cord runs towards

the ﬂ oor.

- If you plug the power plug into the socket in the opposite direction, the electric wires

within the cable may be damaged and this may result in electric shock or ﬁ re.

This appliance must be properly grounded.

Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.

- Improper grounding may result in electric shock, ﬁ re, an explosion, or problems with the

product.

- Never plug the power cord into a socket that is not grounded correctly. Make sure the

socket you use is grounded in accordance with local and national codes.

Do not install this appliance near a heater or ﬂ ammable material.

Do not install this appliance in a humid, oily, or dusty location, or in a location exposed to

direct sunlight or water (rain drops).

Do not install this appliance in a location where gas may leak.

- This may result in electric shock or ﬁ re.

Plug the power plug into the wall socket ﬁ rmly. Do not use a damaged power plug,

damaged power cord, or loose wall socket.

- This may result in electric shock or ﬁ re.

Do not pull or excessively bend the power cord.

Do not twist or tie the power cord.

Do not hook the power cord over a metal object, place a heavy object on the power cord,

insert the power cord between objects, or push the power cord into the space behind the

appliance.

- This may result in electric shock or ﬁ re.

Do not pull the power cord when unplugging the power plug.

- Unplug the power plug by holding the plug.

- Failing to do so may result in electric shock or ﬁ re.

If the power plug or power cord are damaged, contact your nearest service center.

SAVE THESE INSTRUCTIONS

WARNING

WA7000M_EN.indd Sec1:5WA7000M_EN.indd Sec1:5 2/3/2017 11:13:22 AM2/3/2017 11:13:22 AM

English - 6

INSTALLATION CAUTIONS

Position the appliance so that the power plug is easily accessible.

- Failing to do so may result in electric shock or ﬁ re due to electric leakage.

Install your appliance on a level and hard ﬂ oor that can support its weight.

- Failing to do so may result in abnormal vibrations, noise, or problems with the product.

Unplug the power plug when the appliance is not being used for long periods of time or

during a thunder/lightning storm.

- Failing to do so may result in electric shock or ﬁ re.

CRITICAL USAGE WARNINGS

If the appliance is ﬂ ooded, cut the power immediately and contact your nearest service

center.

If the appliance emits a strange noise, a burning smell, or smoke, unplug the power plug

immediately and contact your nearest service center.

- Failing to do so may result in electric shock or ﬁ re.

In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate the area

immediately. Do not turn any appliance or light on or o .

- Do not use a ventilating fan.

- A spark may result in an explosion or ﬁ re.

Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or

other ﬂ ammable or explosive substances.

- This may result in electric shock, ﬁ re, or an explosion.

Do not force the washer lid open while the washer is operating (high-temperature washing/

drying/spinning).

- Water ﬂ owing out of the washer may cause burns or cause the ﬂ oor to be slippery.

This may result in injury.

- Forcing the lid open can damage the product or cause injury.

Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the

washer before using it.

Do not insert your hand under the washer.

- This may result in injury.

safety information

SAVE THESE INSTRUCTIONS

WARNING

CAUTION

WA7000M_EN.indd Sec1:6WA7000M_EN.indd Sec1:6 2/3/2017 11:13:22 AM2/3/2017 11:13:22 AM

English - 7

Do not touch the power plug with wet hands.

- This may result in electric shock.

Do not turn the appliance o by unplugging the power plug while the washer is in operation.

- Plugging the power plug into the wall socket again may cause a spark and result in

electric shock or ﬁ re.

Keep all packaging materials well out of the reach of children, as packaging materials can

be dangerous to children.

- If a child places a bag over their head, the child may su ocate.

Do not let children or inﬁ rm persons use this washer unsupervised.

- Failing to do so may result in electric shock, burns or injury.

Do not insert your hand or a metal object under the washer while it is operating.

- This may result in injury.

Do not attempt to repair, disassemble, or modify the appliance yourself.

- Do not use any fuse (such as copper, steel wire, etc.) other than the standard fuse.

- If you need to repair or reinstall the appliance, contact your nearest service center.

- Failing to do so may result in electric shock, ﬁ re, problems with the product, or injury.

If any foreign substance such as water enters the appliance in any area other than the tub,

unplug the power plug and contact your nearest service center.

- Failing to do so may result in electric shock or ﬁ re.

If the water supply hose comes loose from the faucet and ﬂ oods the appliance, unplug the

power plug.

- Failing to do so may result in electric shock or ﬁ re.

USAGE CAUTIONS

If the washer is contaminated by a foreign substance such as detergent, dirt, food waste,

etc., unplug the power plug and clean the washer using a damp, soft cloth.

- Failing to do so may result in discoloration, deformation, damage or rust.

The clear portion of the lid can be broken by a strong impact. Take care when using the

washer.

- If the clear portion is cracked or broken, it may result in injury.

After a water supply failure or when reconnecting the water supply hose, open the faucet

slowly.

Open the faucet slowly after a long period of non-use.

- The air pressure in the water supply hose or the water pipe may result in damage to a

part or in water leakage.

If a drain error occurs during an operation, check if there is a draining problem.

- If the washer is used when it is ﬂ ooded because of a draining problem, it may result in

electric shock or ﬁ re due to electric leakage.

Do not insert your hand under the washer.

- This may result in injury.

SAVE THESE INSTRUCTIONS

CAUTION

WA7000M_EN.indd Sec1:7WA7000M_EN.indd Sec1:7 2/3/2017 11:13:22 AM2/3/2017 11:13:22 AM

English - 8

Insert the laundry into the washer completely so that laundry does not get caught in the lid.

- If laundry gets caught in the lid, it may result in damage to the laundry or the washer, or

result in water leakage.

Ensure that the faucet is turned o when the washer is not being used.

- Ensure that the water supply hose connectors are properly tightened.

- Failing to do so may result in property damage or injury.

Open the faucet and check if the water supply hose connector is ﬁ rmly tightened and that

there is no water leaking before using the product.

- If the water supply hose connectors are loose, it may result in water leakage.

Do not stand on top of the appliance or place objects (such as laundry, lighted candles,

lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.

- This may result in electric shock, ﬁ re, problems with the product, or injury.

Do not operate the appliance with wet hands.

- This may result in electric shock.

Do not spray volatile material such as insecticide onto the surface of the appliance.

- As well as being harmful to humans, it may also result in electric shock, ﬁ re, or problems

with the product.

Do not place an object that generates a electromagnetic ﬁ eld near the washer.

- This may result in injury due to a malfunction.

Since the water drained during a high-temperature wash or drying cycle is hot, do not touch

the water.

- This may result in burns or injury.

For waterproof fabrics, only use the WATERPROOF cycle.

- Do not use other cycles for waterproof fabrics.

* This may result in injury or damage to the washer, walls, ﬂ oor, or clothing due to

abnormal vibrations.

- Set the temperature and spin according to the attached care label.

Do not operate the washer when detergent dispenser is removed.

- This may result in electric shock or injury due to water leakage.

Do not insert your hand into the detergent dispenser after opening it.

- This may result in injury as your hand may be caught.

safety information

SAVE THESE INSTRUCTIONS

WA7000M_EN.indd Sec1:8WA7000M_EN.indd Sec1:8 2/3/2017 11:13:22 AM2/3/2017 11:13:22 AM

English - 9

Do not place any non-laundry objects, such as shoes, food waste, or animals into the

washer.

- This can cause abnormal vibrations that can damage the washer, and, in the case of

pets, cause severe injury or death.

Do not press the buttons using sharp objects such as pins, knifes, ﬁ ngernails, etc.

- This may result in electric shock or injury.

Do not wash laundry contaminated by oils, creams, or lotions usually found in skincare

shops or massage clinics.

- This may result in the rubber seal becoming deformed and water leakage.

Do not leave metal objects (safety pins, hair pins, etc.) or bleach in the tub for long periods

of time.

- This may cause the tub to rust.

- If rust appears on the surface of the tub, apply a neutral cleansing agent to the surface

and use a sponge to clean it. Never use a metal brush.

Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry

contaminated by dry cleaning detergent.

- This may result in spontaneous combustion or ignition due to heat from the oxidation of

the oil.

Do not use hot water from water cooling/heating devices.

- This may result in problems with the washer.

Do not use natural hand-washing soap in the washer.

- If it hardens and accumulates inside the washer, it may cause problems with the

product, discoloration, rust, or bad odors.

Do not wash large laundry items such as bedding in the washing net.

- Failing to do so may result in injury due to abnormal vibrations.

- Place smaller items, such as lace socks and lingerie in the washing net.

Do not use hardened detergent.

- If it accumulates inside the washer, it may result in water leakage.

Do not wash throw rugs or doormats.

- If you wash throw rugs or doormats, the sand will accumulate inside the washer. It may

result in error such as no draining.

CRITICAL CLEANING INSTRUCTIONS

Do not clean the appliance by spraying water directly onto it.

Do not use the strong acid cleaning agent.

Do not use benzene, thinner, or alcohol to clean the appliance.

- This may result in discoloration, deformation, damage, electric shock, or ﬁ re.

Before cleaning or performing maintenance, unplug the appliance from the wall socket.

- Failing to do so may result in electric shock or ﬁ re.

SAVE THESE INSTRUCTIONS

WARNING

WA7000M_EN.indd Sec1:9WA7000M_EN.indd Sec1:9 2/3/2017 11:13:22 AM2/3/2017 11:13:22 AM

English - 10

installing your washer

UNPACKING YOUR WASHER

Unpack your washer and inspect it for shipping damage. Make sure you have received all the items

shown below. If your washer was damaged during shipping, or you do not have all of the items, contact

1-800-SAMSUNG (1-800-726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the washer.

Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene,

etc.) well out of children’s reach.

When unpacking the washer, 2 person collaboration is needed. To remove the cushion bottom of the

packing materials, forward dumping is strictly prohibited.

When you lay the washer down to remove carton base, should protect the side of washer and lay it

carefully. Never lay your washer on its back or front.

OVERVIEW OF YOUR WASHER

Parts supplied

Hose guide User manual book Plastic zip hose tie Water intake cap

Tools needed

Wrench Flat screwdriver Level Adjustable plier Measuring tape

Parts not supplied

• If you lose an accessory and want to purchase a replacement, contact the

Samsung

service center (1-800-SAMSUNG (1-800-726-7864)).

• The design of the parts and accessories may di er from the pictures above. Their design is

subject to change without notice for product improvement.

• Do not reuse old hoses. Only use new water supply hoses when you install the washing

machine. Old water supply hoses can leak or burst causing ﬂ ooding and property damage.

• Conﬁ rm that there are rubber washers inside the couplings of each water supply hoses.

Water supply hoses

Adjustable legs

Drain Hose

Control panel

Lid

Power Cord

WARNING

CAUTION

WA7000M_EN.indd Sec3:10WA7000M_EN.indd Sec3:10 2/3/2017 11:13:22 AM2/3/2017 11:13:22 AM

English - 11

BASIC LOCATION REQUIREMENTS

Electrical

• 120 Volt 60 Hz 15 AMP fuse or circuit breaker.

• Individual branch circuit serving only your Washer is recommended.

• Your Washer is equipped with a power cord.

NEVER USE AN EXTENSION CORD.

Grounding

ELECTRICAL GROUNDING IS REQUIRED FOR THIS APPLIANCE.

This appliance must be grounded. In the event of malfunction or breakdown, grounding will

reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a power cord having a three-prong grounding plug for use in a

properly installed and grounded outlet.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

An improperly connected equipment-grounding conductor can increase the risk of electrical

shock. Check with a qualiﬁ ed electrician or serviceman if you are not sure whether the

appliance is properly grounded. Do not modify the plug provided with the appliance – if it

does not ﬁ t the outlet, have a proper outlet installed by a qualiﬁ ed electrician.

IMPORTANT SAFETY PRECAUTIONS

• To prevent unnecessary risk of ﬁ re, electrical shock or personal injury, all wiring and

grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No.

70 Latest Revision and local codes and ordinances. It is the personal responsibility of the

appliance owner to provide adequate electrical service for this appliance.

NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR

HOT WATER PIPES.

Water

To correctly ﬁ ll your Washer in the proper amount of time, water pressure of 20 to 116psi (137 to

800kPa) is required.

Water pressure less than 20 psi may cause water valve failure, or may not allow the water valve

to shut o completely, or may extend the ﬁ ll time beyond what your Washer controls allow,

causing your Washer to turn o . A time limit is built into the controls to prevent ﬂ ooding in your

home if a hose becomes loose.

The water faucets must be within 4 feet / 122 cm of the back of your Washer to match the inlet

hoses provided with your Washer.

Accessory inlet hoses are available in various lengths up to 10 feet / 275 cm for faucets that

are further away from the back of your Washer.

To avoid the possibility of water damage:

• Have water faucets easily accessible.

• Turn o faucets when the washer is not in use.

• Periodically check that there is no leakage from the water inlet hose ﬁ ttings.

CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS.

01 installing your washer

CAUTION

WARNING

CAUTION

WARNING

WA7000M_EN.indd Sec3:11WA7000M_EN.indd Sec3:11 2/3/2017 11:13:23 AM2/3/2017 11:13:23 AM

English - 12

Drain facility

The recommended height of the standpipe is 39 in / 99 cm. The drain hose must be routed

through the drain hose clip to the standpipe. The standpipe must be large enough to accept the

outside diameter of the drain hose. The drain hose is attached to the washer at the factory.

Flooring

For best performance, you must install your washer on a solidly constructed ﬂ oor. Wood ﬂ oors

may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting

and soft tile surfaces are contributing factors to vibration which can cause your washer to move

slightly during the spin cycle.

Never install your washer on a platform or weakly supported structure.

Location considerations

Do not install your washer in areas where water may freeze, since your washer will always retain

some water in its water valve, pump, and hose areas. Frozen water can damage the belts, the

pump, hoses, and other components.

Alcove or closet installation

MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:

Sides – 1 in / 25 mm

Rear – 6 in / 152 mm

Closet Front – 2 in / 51 mm

TOP - 21 in / 533 mm

Gap between end of water valve and the wall

- Case 1. Assemble supply hose after installing : Over 3.9 in (10 cm).

- Case 2. Assemble supply hose before installing : Over 2.8 in (7cm).

If the washer and dryer are installed together, the closet front must have at least a 72 in² (465 cm²)

unobstructed air opening. Your washer alone does not require a speciﬁ c air opening.

A. Recessed area

B. Side view - closet or conﬁ ned area

installing your washer

2 in.

(5.1 cm)

6 in.

(15.2 cm)

29.3 in.

(74.4 cm)

21 in.

(53.3 cm)

Case 1. 3.9 in. (10 cm)

Case 2. 2.8 in. (7 cm)

1 in.

(2.5 cm)

1 in.

(2.5 cm)

27.0 in.

(68.6 cm)

27.0 in.

(68.6 cm)

1 in.

(2.5 cm)

WA7000M_EN.indd Sec3:12WA7000M_EN.indd Sec3:12 2/3/2017 11:13:23 AM2/3/2017 11:13:23 AM

English - 13

Required dimensions for Installation

WA45M7050A*

27.0 in.

(68.6 cm)

43.9 in.

(111.5 cm)

39.3 in.

(99.8 cm)

29.3 in.

(74.4 cm)

29.3 in.

(74.4 cm)

43.9 in.

(111.5 cm)

58.1 in.

(147.6 cm)

Closet or Door

48 in.² *

(310 cm²)

24 in.² *

(155 cm²)

3 in.

(7.6 cm)

3 in.

(7.6 cm)

*Required spacing

WA50M7450A*

27.0 in.

(68.6 cm)

45.0 in.

(114.4 cm)

40.2 in.

(102.2 cm)

29.3 in.

(74.4 cm)

29.3 in.

(74.4 cm)

45.0 in.

(114.4 cm)

59.0 in.

(150.0 cm)

Closet or Door

48 in.² *

(310 cm²)

24 in.² *

(155 cm²)

3 in.

(7.6 cm)

3 in.

(7.6 cm)

*Required spacing

01 installing your washer

WA7000M_EN.indd Sec3:13WA7000M_EN.indd Sec3:13 2/3/2017 11:13:23 AM2/3/2017 11:13:23 AM

English - 14

installing your washer

IMPORTANT NOTE TO INSTALLER

Please read the following instructions carefully before installing your washer.

These instructions should be retained for future reference.

We recommend you hire a professional to install this washer.

Installation ﬂ ow chart

STEP 1 Selecting a Location

Before you install the washer, make sure the location:

• Has a hard, level surface without carpeting or ﬂ ooring that may obstruct ventilation.

• Is away from direct sunlight.

• Has adequate ventilation.

• Is not exposed to freezing temperatures (temperatures under 32 °F or 0 °C).

• Is away from heat sources such as oil or gas.

• Has enough space so that the washer doesn’t rest on its power cord.STEP 2

Connecting the water and the drain

Connecting the water supply hose

Before installing the water supply hoses, make sure there are

rubber gaskets inside the ﬁ ttings at both ends of each new

water hose. Installing the water supply hoses without rubber

gaskets can cause water leakage.

When you initially install the washer, be sure to use new hoses.

Failing to do so may result in a water leakage or overﬂ ow and

may damage your property.

Do not connect multiple water supply hoses together to

increase the length of the supply hose. Hoses connected this

way can leak and the leakage can cause electrical shock. If a

hose is too short, replace the hose with a longer, high pressure

hose.

Selecting

a location

Removing the

shipping bolts

(*Drum only)

Adjusting the

levelling feet

Connecting the water

and the drain

[Running a test cycle]

Run a test cycle(Rinse+Spin)

with small amount of laundary

(about 4~5 Towels)

Running

a Calibration

mode

Powering your

washing machine

Finish the

installation

Does a

Laundary machine

Vibrate?

Yes

Please check again before steps.

Rubber Washer

Coupling

CAUTION

WA7000M_EN.indd Sec3:14WA7000M_EN.indd Sec3:14 2/3/2017 11:13:23 AM2/3/2017 11:13:23 AM

English - 15

1. Connect the ends of the water supply hoses to the HOT and COLD

faucets.

2. Tighten the ﬁ ttings by hand until they are snug, and then tighten them an

additional two-thirds of a turn with a plier.

When you fasten the ﬁ ttings, do not fasten them too tightly or apply

tape or sealant to the faucets or water supply intakes. This can

damage the ﬁ ttings.

After you have connected the water supply hoses to the faucets,

ensure that they are connected correctly by pulling the water supply

hoses downwards

3. Place the unconnected ends of the hoses into a bucket and open the

faucets connected to the two water supply hoses for 10 or 15 seconds to

remove any foreign substances from the hoses. Close the faucets before

continuing.

4. Connect the ends of the water supply hoses to the water supply intake

connections at the back of the washer.

The water supply hose connected to the HOT faucet must be

connected to the hot water supply intake and the water hose

connected to the COLD faucet must be connected to the COLD

water supply intake.

5. Tighten the ﬁ ttings by hand until they are snug, and then tighten them

an additional two-thirds of a turn with a plier.

To ensure the correct water usage, connect both the HOT and

COLD water faucets. If either or both are not connected, an “4E”

(no ﬁ ll) error can occur.

If you do not want to use the HOT water supply hose, insert

the water intake cap into the HOT water supply intake hole. In

this case, you must select the Tap Cold option for the water

temperature. If you select the Tap Cold option, all the lamps for

the water temperature options are turned o .

Conﬁ rm that the water supply hoses are not twisted or bent. If the

hoses are twisted or bent, the hoses can leak and cause electric

shock due to the water leakage.

6. Turn on the HOT and COLD water supplies and check all the water

supply intake connections and the faucets for water leaks.

01 installing your washer

CAUTION

WA7000M_EN.indd Sec3:15WA7000M_EN.indd Sec3:15 2/3/2017 11:13:24 AM2/3/2017 11:13:24 AM

English - 16

installing your washer

Connecting the drain hose

The end of the drain hose can be positioned in three ways:

In a Wall standpipe or Floor standpipe

The height of end of standpipe must be no lower than 39 in (99 cm) and no

higher than 96 in (245 cm).

If drain pipe are built into the wall with water valves (A), fasten the drain hose

to the water hose.

Make sure that the connection between the drain hose and the

standpipe is not airtight.

In a laundry tub

The height of the tub must be no lower than 39 in (99 cm) and no higher than

96 in (245 cm).

Assemble the supplied Hose guide at the end of the drain hose, and put the

hanger on laundry tub.

And fasten the drain hose to the leg of laundry tub.

Connect the hose guide (A) within 3~5 in (7.6~12.7 cm)* from the end of

the drain hose. If the drain hose is extended beyond the end of the hose

guide, mold or microorganisms could spread inside the washer.

Drain Hose can be installed until 96 in (245cm) maximum. But drain

capability can be reduced at this height. It causes the washer to have

odor, because of remained water in the drain system.

If the drain hose is installed below 39 in (99 cm), water can be drained in cycles due to a

siphon phenomenon. It causes the washer to display a “4E” error code.

STEP 3

Leveling your washer

See if the washer is level by checking the position of the tub:

1. Slide the washer into position.

2. Open the lid of the washer, and pour the water into the tub to

just below the pulsator level.

3. If the washer is level, the pulsator is positioned at the center of the

water as shown in the ﬁ gure. If not, level your washer by turning the

front leveling feet clockwise or counterclockwise as necessary.

Turn the front leveling feet clockwise to raise the washer, and

counterclockwise to lower the washer.

The number of leveling feet di ers with the model.

Loosen Lock

Pulsator

Adjustable legs

(three)

WA7000M_EN.indd Sec3:16WA7000M_EN.indd Sec3:16 2/3/2017 11:13:24 AM2/3/2017 11:13:24 AM

English - 17

STEP 4

Powering your washer

Plug the power cord into a 3-prong, well grounded 120 volt 60

Hz approved electrical outlet protected by a 15-amp fuse or

comparable circuit breaker.

Your washer is grounded through the third prong of the power

cord when plugged into a three-prong grounded electrical

outlet.

Test run

Make sure that you install your washing machine correctly by running the Rinse+Spin cycle

after the installation is complete.

STEP 5

Running a test cycle

Run a test cycle as follows to check if your washer is properly installed.

1. Load about 6 pounds of laundry into the tub.

2. Press the Power button to turn on your washer.

3. Select the Rinse+Spin cycle by turning the Cycle Selector.

4. Press the Start/Pause button to start the test cycle.

5. The washer should not rock or vibrate excessively when water is supplied or when washing

or spinning, and should drain well during the spin cycle.

If water leaks while water is being supplied or drained, check the water connections. Refer

to the “Connecting the water and the drain” section on pages 14~15 for instructions.

If the washer rocks and vibrates excessively, level your washer again. Refer to the “Leveling

your washer” section on page 15 for instructions.

STEP 6

Calibration mode

Your Samsung washing machine detects the laundry weight automatically.

For more accurate weight detection, please run Calibration Mode after the installation.

To run Calibration Mode, follow these steps:

1. Remove laundry or any contents in the machine.

2. Press the Temp. and Delay End buttons simultaneously, and then press the Power button.

The machine turns on.

3. Press the Start/Pause button to activate “Calibration Mode”.

4. The pulsator rotates clockwise and counterclockwise for approximately 1 minute.

5. When “Calibration Mode” is ﬁ nished, “End” (WA50M7450A*) / “0” (WA45M7050A*) appears

on the display, and the machine automatically turns o .

The washing machine is now ready for use.

01 installing your washer

WA7000M_EN.indd Sec3:17WA7000M_EN.indd Sec3:17 2/3/2017 11:13:25 AM2/3/2017 11:13:25 AM

English - 18

operating instructions

WARNING: To reduce the risk of ﬁ re, electric shock, or injury to persons when using your appliance,

follow basic precautions, including the following:

LOADING YOUR WASHER

• Fill the tub with dry, unfolded clothes evenly around in order to enhance washing e ciency and prevent

excess wear, or wrinkling of the load.

- For optimal washing performance, make sure the laundry is piled up evenly.

• Wash delicate items such as bras, hosiery, and other lingerie in the Delicates cycle

with similar lightweight items.

• When washing big bulky items or a few smaller items that don’t ﬁ ll the tub

completely – a rug, a pillow, stu ed toys, or one or two sweaters, for example –

add a few towels to improve spin performance.

• Do not insert bulky items except for Bedding in this cycle.

During the spin cycle, the washer may add additional water to redistribute the clothes and correct an

imbalance inside the drum.

• When washing heavily soiled loads, do not overload your washer to ensure good cleaning results.

• Inﬂ atable items may cause damage to the laundry or the machine during the wash or drying

process.

• Regardless of the size, blankets or quilts are safer and cleaner to wash one item at a time.

Two di erent-sized blankets in the same load may compromise the drying performance due to

unbalanced loads.

To input a blanket

Fold the blanket into the blanket-speciﬁ c net as shown, and then insert in the tub below the plastic

area of the tub.

Make sure the laundry is inserted completely.

• Any exposed part of the laundry may cause damage to the machine or the laundry itself, or a water

leak.

• Do not overload the tub. Make sure no part of the laundry is exposed outside of the tub.

To add a forgotten item:

1. Press the Start/Pause button to pause the washer.

2. Wait for the door to unlock automatically, and then open the door.

3. Add the item, close the door, and then press the Start/Pause button. The cycle will resume.

GETTING STARTED

1. Load your washer.

2. Add liquid (or powder) detergent and additives to the dispenser (see pages 24~26).

3. Select the appropriate cycle and options for the load (see pages 18~23).

4. Close the lid.

5. Press the Start/Pause button.

6. The Wash Indicator light illuminates.

7. The estimated cycle time will appear in the display.

The time may ﬂ uctuate to indicate the time remaining in the cycle better.

The actual time required for a cycle may di er from the estimated time in the display depending on the

water pressure, water temperature, detergent, and laundry.

8. Before your washer starts to ﬁ ll, it will make a series of clicking noises to check the door lock and do a

quick drain.

• When the cycle is complete, the Door Lock light will go out and “End” (WA50M7450A*) / “0”

(WA45M7050A*) will appear in the display.

• Pressing the Power button cancels the cycle and stops your washer.

•

The Wash, Rinse , and Spin indicator lights will illuminate during those portions of the cycle.

WARNING

WA7000M_EN.indd 18WA7000M_EN.indd 18 2/3/2017 11:13:25 AM2/3/2017 11:13:25 AM

English - 19

washing a load of laundry

OVERVIEW OF THE CONTROL PANEL

Cycle Selector

Select the appropriate cycle for the type of load.

The cycle you select determines the tumble pattern and spin speed for the

cycle.

To minimize wrinkling of laundry, select the PERM PRESS cycle.

NORMAL - For most fabrics including cottons, linens, and normally soiled

garments.

HEAVY DUTY - For sturdy, colorfast fabrics and heavily soiled garments.

BRILLIANT WHITES (WA50M7450A*)

- For white fabrics with or

without bleach.

BEDDING/WATERPROOF - For bulky and large items, such as

comforters, blankets and sheets. When washing comforters, use liquid

detergent, waterproof or water-resistant items.

 Do not wash waterproof items and non-waterproof items together.

 Check the speciﬁ cation label on the fabric item and see if the item is

waterproof.



Use the bedding/waterproof cycle for waterproof or water-resistant items

such as plastic mats, ski pants, raincoat and comforters which hardly

absorb water.

DEEP WASH

- Use more water in washing and rinsing.

DELICATES - For sheer fabrics, bras, lingerie, silks, and other handwash-

only fabrics. For best results, use liquid detergent.

03 washing a load of laundry

WA45M7050A*

WA50M7450A*

3 5

1 6

WA7000M_EN.indd 19WA7000M_EN.indd 19 2/3/2017 11:13:25 AM2/3/2017 11:13:25 AM

English - 20

PERM PRESS - For wash-and-wear, synthetic fabrics, and lightly to normally

soiled garments.

ACTIVE WEAR (WA50M7450A*) - Use this cycle to wash exercise wear such as

sports jerseys, training pants, shirts/tops and other performance clothing. This

cycle provides e ective soil removal with gentle action for special fabric care.

QUICK WASH - For lightly soiled garments needed quickly.

SPIN - Drains the water and spins at a high speed.

RINSE + SPIN - Use for loads that need rinsing only or to add rinse-added

fabric softener to a load.

Display

Provides instructions and diagnostics while keeping you updated on the cycle

status and time remaining.

Temp. selection

button

Press the button repeatedly to cycle through the di erent water temperature options.

Hot - Whites and heavily soiled, colorfast items.

Warm - Colorfast items.

Eco Warm - Moderately soiled, colorfast items; most wrinkle-free items.

Cool - Brightly colored, very lightly soiled items.

Cold - Cold water with no warm water added.

 If you select the Cold option, all the lamps for the water temperature options

are turned o .

Spin selection

button

Press the button repeatedly to cycle through the di erent spin speed options.

High - Use for underwear, t-shirts, jeans, and sturdy cottons.

Medium - Use for jeans, wrinkle-free or wash-and-wear items, and synthetics.

Low - Use for delicate items needing a slow spin speed.

No Spin - Drains your washer without spinning. Use for extremely delicate items

that cannot tolerate any spin.

Soil Level

selection button

Press the button to select the soil level/washing time.

Heavy - For heavily soiled loads.

Normal - For moderately soiled loads. This setting is best for most loads.

Light - For lightly soiled loads.

Select Cycle

Option

Press these buttons to select di erent cycle options.

Extra Rinse - Change from spray rinse mode to deep rinse mode, and rinse once

again.

Delay End - Delay the end of any cycle for up to 19 hours in one-hour increments.

Displayed hour indicates the time the wash will be ended.

Self Clean - Use to clean dirt and bacteria from the drum. Regular use (after every

40 washes) is recommended. No detergent or bleach is needed.

Pre Soak - It adds 15 minutes soaking time at the start of the wash cycle for

better stain removal.

Start/Pause

selection button

Press to pause and restart cycles.

Power button

Press once to turn your washer on. Press again to turn your washer o . If the

washer is left on for more than 10 minutes without any buttons being pressed, the

power automatically turns o .

washing a load of laundry

WA7000M_EN.indd 20WA7000M_EN.indd 20 2/3/2017 11:13:26 AM2/3/2017 11:13:26 AM

English - 21

Child Lock [ ]

Child Lock prevents children from playing with your washer.

Activating the Child Lock function

Press and hold the Spin and Soil Level buttons simultaneously for approximately 3 seconds.

• When you activate the Child Lock function, the “Child Lock [

]” lamp blinks.

Using the Child Lock function

If the lid is opened when the Child Lock function is on, “dE” is displayed and an alarm sounds.

• If the water level in the tub is above the safe water level, “dE” is displayed on the LED display

and the washing machine starts to drain water by force after 30 seconds.

• If the water level in the tub is above the safe water level and the Child Lock function is turned

on while the door is open, “CL” is displayed on the LED display even if the power of the

washing machine is turned o and the washing machine drains water by force.

• Even if the power of the washing machine is turned o , if the lid is opened while the water

level in the tub is above the Reset water level, “CL” is displayed on the LED display without

the alarm sounding and the washing machine starts to drain water. When the draining

operation ﬁ nishes, the power is automatically turned o again.

• You have activated the Child Lock function while the washing machine is running, the Start/

Pause button will not work.

• After the compulsory drain, the “CL” code display blinks at 1 second intervals and the

product enters the “CL” mode. (When the product is in the “CL” mode, only the Power

button works.)

• To cancel the “CL” mode, you need to turn the power o and then on again.

• To cancel the “dE” mode, deactivate the Child Lock function. To deactivate the Child Lock

function, press and hold the Spin and Soil Level buttons simultaneously for at least

3seconds.

Adding laundry when Child Lock is on

• To add laundry, deactivate the Child Lock function. To deactivate the Child Lock function,

press and hold the Spin and Soil Level buttons simultaneously for at least 3seconds.

See “Pause Option” on page 23 for additional details.

Deactivating the Child Lock function

Press and hold both the Spin and Soil Level buttons simultaneously for approximately

3seconds.

• When you deactivate the Child Lock function, the “Child Lock [

]” is turned o .

• The Child Lock function prevents children or the inﬁ rm from accidently operating the washer

and injuring themselves.

• If a child enters the washing machine, the child may become trapped and su ocate.

• Once you have activated the Child Lock function, it continues working even if the power

is turned o .

• Forcing the lid open can result in injury or damage to the product.

To add laundry after you have activated the Child Lock function, you must ﬁ rst deactivate

the Child Lock function.

03 washing a load of laundry

CAUTION

WARNING

WA7000M_EN.indd 21WA7000M_EN.indd 21 2/3/2017 11:13:26 AM2/3/2017 11:13:26 AM

English - 22

Sound

The Sound O function can be selected during all cycles.

Garment

You can add or take out laundry items even after the wash has started, as long as the

“Garment” light is on. Pushing the Start/Pause button unlocks the lid. If you open the lid and

want to continue the wash cycle, close the lid, and then press the Start/Pause button.

If you have activated the Child Lock, you must deactivate it ﬁ rst. See page 20.

Delay End

You can set the washing machine to start your wash automatically at a later time, by choosing a delay

time.

The hour displayed indicates the time at which the wash will be ended.

1. Set your wash cycle.

2. Press the Delay End button repeatedly until the delay time is set.

3. Press the Start/Pause button. The “Delay End” indicator will be lit, and the clock will begin

counting down until it reaches the set time.

4. To cancel a Delay End function, press the Power button and then turn the washing machine on

again.

Pre Soak

Use this function when the laundry is heavily contaminated or stained. This function improves the

wash performance by adding a Pre Soak cycle.

- If you select this function, the total cycle time is increased by 15 minutes.

- When the Pre Soak cycle starts, the washing machine repeats a wash cycle after supplying

water and then performs a 15-minute soak cycle.

- When the Pre Soak cycle is complete, the conﬁ gured wash cycle starts without draining

water.

washing a load of laundry

WA7000M_EN.indd 22WA7000M_EN.indd 22 2/3/2017 11:13:26 AM2/3/2017 11:13:26 AM

English - 23

Mist Shower

Mist Shower sprays water from a nozzle that is independent of the main water supply system.

This soaks the laundry with water from the beginning of the rinse cycle and ensures an e ective

wash even with a small amount of water.

(The Mist Shower function may not work if there is too

large of a load in the machine.)

Smart Care

This function enables you to check the status of the washing machine using a smartphone.

1. To enable the Smart Care function, press and hold the Pre Soak key for 3 seconds after

turning the power on or when an error occurs.

• The error code history is deleted after you use this function.

2. The Smart Care indicator is lit on the display.

3. Run the Smart Care app on your smart phone.

• Android : Galaxy series, Galaxy Note series (Other devices may not be normal operation).

Supported operating system: Android 2.2 or higher.

• IOS : IPhone series

Supported operating system : OS 4.3 or higher.

4. Focus your smart phone’s camera on the display panel of the washing machine.

5. If the smart phone’s camera is focused on the display panel of the washing machine,

the panel and error message is automatically recognized and the error type and

countermeasures are displayed on the smart phone.

6. If the smartphone fails to recognize the error code more than twice, please enter the error

code displayed on the display panel of the washer manually into the Smart Care app.

Downloading the Smart Care app

• Download the Samsung Laundry App into your mobile phone from the Android market

or Apple App store. (Search word : Samsung Smart Washer/Dryer)

Precautions when using Smart Care

• If light from a light bulb, ﬂ uorescent bulb, or lamp is reﬂ ected on the display panel of

the washing machine, the smartphone may not be able to recognize the panel or error

message easily.

• If you hold the smartphone at too large an angle relative to the front of the display panel,

it may not be able to recognize the error code. For best results, hold the smartphone so

that the front of the panel and the smartphone are parallel or nearly parallel.

blue round object located

left to detergent dispenser

03 washing a load of laundry

WA7000M_EN.indd 23WA7000M_EN.indd 23 2/3/2017 11:13:26 AM2/3/2017 11:13:26 AM

English - 24

Washing clothes using the cycle selector

Your new washing machine makes washing clothes easy, using Samsung’s “Fuzzy Control”

automatic control system. When you select a wash program, the machine will set the correct

temperature, washing time, and washing speed.

1. Press the Power button.

2. Open the lid.

3. Load the articles of clothing one at a time loosely into the drum, without overﬁ lling it.

4. Add liquid (or powder) detergent, softener, and/or bleach (if necessary) to the appropriate

compartments. See pages 24~26.

5. Close the lid.

6. Use the Cycle Selector to select the appropriate cycle according to the type of material:

NORMAL, HEAVY DUTY, COLORS/DARKS, BEDDING, DELICATES,

WATERPROOF, PERM

PRESS, ACTIVE WEAR, QUICK WASH, SPIN, RINSE+SPIN. The relevant indicators will

illuminate on the control panel.

7. At this time, you can control the wash temperature, the number of rinse cycles, the spinning

speed, and the delay time by pressing the appropriate option button.

8. Press the Start/Pause button on the Cycle Selector and the wash will begin. The process

indicator will light up and the remaining time for the cycle will appear in the display.

Pause Option

To remove or add laundry items, follow these steps:

1. Press the Start/Pause button to unlock the lid.

The lid cannot be opened when the water is too HOT.

2. Remove or add laundry items.

3. Close the lid, and then press the Start/Pause button to restart the wash.

If you have Child Lock on, you must deactivate it ﬁ rst. See page 20.

When the cycle is ﬁ nished:

After the total cycle has ﬁ nished, the power will turn o automatically.

1. Open the lid.

2. Remove laundry.

ATC (AUTO TEMPERATURE CONTROL)

ATC is the control function that the washer controls water temperature with temperature sensor (thermistor).

Because there are numerous water temperatures depending on the customer’s environments (cold

areas, warm areas, various water temperatures, settings of heater temperature, etcs.), ATC function in

our washer maintains the certain level of wash temperature to output the best washing performance at

each cycle.

If you select normal & heavy duty cycles, those cycles are the regulation and UL cycle. Since new

washer must reduce the amount of energy usage at ﬁ rst priority, customer will notice more cold water

entering the washer. But This is Normal, not a problem.

In those regulation cycles, Hot temperature is similar to acceptable adult bath-water temperature and

warm temperature is similar to comfortable swimming-pool water temperature.

If customers want to wash clothes in speciﬁ c water temperature, customers should choose a di erent

cycle at each temperature (Hot/Warm/Eco Warm)

washing a load of laundry

WA7000M_EN.indd 24WA7000M_EN.indd 24 2/3/2017 11:13:26 AM2/3/2017 11:13:26 AM

English - 25

DETERGENT USE

Your washer is designed to use high e ciency (HE) detergents.

• For best cleaning results, use high e ciency detergent such as Tide

HE, Wisk HE, Cheer HE or Gain HE*. High e ciency detergents

contain suds suppressors that reduce or eliminate suds. When fewer

suds are produced, the load tumbles more e ciently and cleaning is

maximized.

Regular detergent is not recommended. Use HE detergents only.

Reducing the amount of detergent may reduce the quality of cleaning. It is important to pre–treat

stains, sort carefully by color and soil level, and avoid overloading.

* Brand names are trademarks of their respective manufacturers.

FEATURES

Automatic dispenser

Your washer has separate compartments for dispensing detergent and color-safe bleach and

fabric softener. Add all laundry additives to their respective compartments before starting your

Washer.

The automatic dispenser MUST ALWAYS be in place before you start your washer.

DO NOT open the automatic dispenser when your washer is running.

• Never exceed the manufacturer’s recommendations when adding detergent.

• This compartment holds liquid detergent for the main wash cycle, which is added to the

load at the beginning of the cycle.

• When using powdered detergent, remove the liquid detergent compartment from the

detergent drawer. The washer will not dispense powdered detergent from the liquid

detergent compartment.

To add detergent to the automatic dispenser:

1. Open the dispenser drawer.

2. Load the recommended amount of liquid (or powder) detergent into the detergent

compartment before you start your wash.

3. Close the drawer slowly and smoothly to avoid spilling, splashing, or premature dispensing of

the contents.

It is normal for a small amount of water to remain in the

dispenser compartments at the end of the cycle.

Do not put chlorine bleach in the dispenser drawer.

03 washing a load of laundry

WARNING

Liquid detergent

compartment

WA7000M_EN.indd 25WA7000M_EN.indd 25 2/3/2017 11:13:26 AM2/3/2017 11:13:26 AM

English - 26

Loading the Liquid (or Powder) detergent compartment

1. Pour the recommended amount of laundry detergent

directly into the detergent compartment before starting

your washer.

2. If you are using color-safe bleach, add it with the detergent

to the detergent compartment.

When adding color-safe bleach with detergent, it is best if

both laundry products are in the same form – liquid.

When using powdered detergent, remove the liquid

detergent compartment from the detergent drawer. The

washer will not dispense powdered detergent from the

liquid detergent compartment.

Loading the Bleach compartment

(Liquid chlorine bleach only)

1. Add chlorine bleach to the bleach compartment.

DO NOT exceed the MAX FILL line.

• Avoid splashing or over–ﬁ lling the compartment.

• Your washer automatically dispenses bleach into the

tub at the appropriate time.

2. The dispenser automatically dilutes liquid chlorine bleach

before it reaches the wash load.

• Never pour undiluted liquid chlorine bleach directly

onto the load or into the tub. It is a powerful chemical

and can cause fabric damage, such as weakening of

the ﬁ bers or color loss, if not used properly.

• If you prefer to use color–safe, non–chlorine bleach,

add it to the appropriate detergent compartment.

DO NOT pour color–safe bleach into the Bleach compartment.

washing a load of laundry

Liquid detergent

compartment

Bleach

compartment

WA7000M_EN.indd 26WA7000M_EN.indd 26 2/3/2017 11:13:27 AM2/3/2017 11:13:27 AM

English - 27

Loading the Fabric softener compartment

1. Pour the recommended amount of liquid fabric softener

into the softener compartment.

For smaller loads, use less than one capful.

2. Dilute the fabric softener with water until it reaches MAX

FILL in the compartment.

3. The dispenser automatically releases liquid fabric softener

at the proper time during the rinse cycle.

• Use the softener compartment ONLY for liquid fabric

softeners.

• DO NOT use the Downy Ball* in the fabric softener

compartment with this washer. It will not add fabric

softener at the appropriate time.

Use the detergent compartment.

• Do not use liquid fabric softener that is too sticky as it may not mix with the water

su ciently.

* Brand names are trademarks of their respective manufacturers.

03 washing a load of laundry

Fabric softener

compartment

WA7000M_EN.indd 27WA7000M_EN.indd 27 2/3/2017 11:13:27 AM2/3/2017 11:13:27 AM

English - 28

maintaining your washer

CLEANING THE EXTERIOR

Turn o the water faucets after ﬁ nishing the day’s washing.

This will shut o the water supply to your washer and prevent the unlikely possibility of damage from

escaping water. Leave the lid open to allow the inside of your washer to dry out.

Use a soft cloth to wipe up all detergent, bleach or other spills as they occur.

Clean the following as recommended:

Control Panel – Clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads. Do not spray

cleaners directly on the panel.

CLEANING THE INTERIOR

Clean the interior of your washer periodically to remove any dirt, soil, odor, mold, mildew, or bacterial

residue that may remain in your washer as a result of washing clothes.

Failure to follow these instructions may result in unpleasant conditions, including odors and/or permanent

stains on your washer or laundry.

Hard water deposits may be removed, if needed. Use cleaners labeled “Washer safe”.

STORING YOUR WASHER

Washers can be damaged if water is not removed from hoses and internal components before storage.

Prepare your washer for storage as follows:

• Select the Quick Wash cycle and add bleach to the automatic dispenser. Run your washer through the

cycle without a load.

• Turn the water faucets o and disconnect the inlet hoses.

• Unplug your washer from the electrical outlet and leave your washer lid open to let air circulate inside the

drum.

• If your washer has been stored in below–freezing temperatures, allow time for any leftover water in your

washer to thaw out before use.

PRESERVING THE TOP COVER AND THE FRONT FRAME

Do not place any heavy or sharp objects or a detergent box on the washing machine. They can scratch or

damage the top cover of the unit.

Since the entire washing machine has a high-gloss ﬁ nish, the surface can be scratched or damaged.

Avoid scratching or damaging the surface when using the washing machine.

CLEANING MESH FILTER

Clean the mesh ﬁ lter of the water hose once or twice a year.

1. Turn o the washer, and then unplug the power cord.

2. Close the faucet.

3. Loosen and disconnect the water hose from the back of the washer.

Cover the hose with a cloth to prevent water from gushing out.

4. Use pliers to pull out the mesh ﬁ lter from the inlet valve.

5. Submerge the mesh ﬁ lter deeply in water so that the threaded

connector is also submerged.

6. Dry the mesh ﬁ lter completely in a shaded area.

7. Reinsert the mesh ﬁ lter into the inlet valve, and reconnect the water

hose to the inlet valve.

8. Open the faucet.

If the mesh ﬁ lter is clogged, the “4E” information code appears on the

washer’s display screen.

WA7000M_EN.indd 28WA7000M_EN.indd 28 2/3/2017 11:13:27 AM2/3/2017 11:13:27 AM

English - 29

CLEANING THE DISPENSERS

The automatic dispenser may need to be cleaned periodically due to laundry additive buildup.

1. Pull the dispenser drawer straight back until it stops.

2. Tilt the dispenser drawer upward and remove it.

3. Remove the inserts from the 3 compartments. Rinse the

inserts and the drawer with warm water to remove traces

of accumulated laundry products.

4. To clean the drawer opening, use a small, non-metal brush

to clean the recess. Remove all residue from the upper and

lower parts of the recess.

5. Return the inserts to the proper compartments and replace

the drawer. By placing the dispenser drawer rail  on

top of the compartment rail  (Tilt the dispenser drawer

downward and insert it.), and then push the drawer in ﬁ rmly

and slowly.

04 maintaining your washer

WA7000M_EN.indd 29WA7000M_EN.indd 29 2/3/2017 11:13:27 AM2/3/2017 11:13:27 AM

English - 30

SELF CLEAN

Self Clean is a self-cleaning cycle that removes mold that may

occur inside the washing machine.

1. Press the Power button.

2. Select the Self Clean cycle.

• Once the Self Clean cycle is selected, the only

function that can be set is Delay End.

3. Press the Start/Pause button.

• If you press the Start/Pause button, Self Clean

begins.

• Using Self Clean, you can clean the drum without using a

cleansing agent.

• Never use Self Clean when laundry is in the washing

machine. This may cause damage to the laundry or a

problem with the washing machine.

The Self Clean Auto Indicator Function

• If the “Self Clean” indicator is lit after a wash, it indicates

that tub (drum) cleaning is required. In this case, remove

the laundry from the washing machine, turn the power on,

and clean the drum by running Self Clean.

• If you do not run Self Clean, the “Self Clean” indicator

turns o . However, the “Self Clean” indicator will light

again after two washes. Not running Self Clean at this point

will not cause a problem with the washing machine.

• Although the Self Clean Auto Indicator appears once a

month or so, the frequency may di er depending on the

number of times the washing machine is used.

WA50M7450A*

WA45M7050A*

CAUTION

WA50M7450A*

WA45M7050A*

maintaining your washer

WA7000M_EN.indd 30WA7000M_EN.indd 30 2/3/2017 11:13:27 AM2/3/2017 11:13:27 AM

English - 31

troubleshooting

CHECK THESE SOLUTIONS IF YOUR WASHER…

PROBLEM SOLUTION

Will not start. • Make sure the lid is closed.

• Make sure your washer is plugged in.

• Make sure the water source faucets are open.

• Make sure to press the Start/Pause button to start your Washer.

• Make sure Child Lock is not activated. See page 20.

• Before your washer starts to ﬁ ll, it will make a series of clicking noises

to check the lid lock and do a quick drain.

• Check the fuse or reset the circuit breaker

Has no water or not enough

water.

• Turn both faucets on fully.

• Straighten the water inlet hoses.

• Disconnect hoses and clean the screens. Hose ﬁ lter screens may be

clogged.

Has detergent remaining

in the automatic dispenser

after the wash cycle is

complete.

• Make sure your washer is running with su cient water pressure.

Vibrates or is too noisy. • Make sure your washer is set on a level surface. If the surface is not

level, adjust your washer’s feet to level the appliance.

• Make sure your washer is not touching any other object.

• Make sure the laundry load is balanced.

Stops • Plug the power cord into a live electrical outlet.

• Check the fuse or reset the circuit breaker.

• Close the lid and press the Start/Pause button to start your washer.

For your safety, your washer will not spin unless the lid is closed.

• Before your washer starts to ﬁ ll, it will make a series of clicking noises

to check the lid lock and do a quick drain.

• There may be a pause or soak period in the cycle. Wait and it may

start.

• Check the screens on the inlet hoses at the faucets for obstructions.

Clean the screens periodically.

05 troubleshooting

WA7000M_EN.indd 31WA7000M_EN.indd 31 2/3/2017 11:13:28 AM2/3/2017 11:13:28 AM

English - 32

PROBLEM SOLUTION

Fills with the wrong

temperature water.

• Turn both faucets on fully.

• Make sure the temperature selection is correct.

• Make sure the hoses are connected to the correct faucets.

Flush water lines.

• Disconnect the hoses and clean the screens. The hose ﬁ lter screens

may be plugged.

• As your washer is ﬁ lling, the water temperature may change as

the automatic temperature control feature checks incoming water

temperature. This is normal.

• While your washer is ﬁ lling, you may notice just hot and/or just

cold water going through the dispenser when you have selected

cold or warm wash temperatures. This is a normal function of the

automatic temperature control feature as your washer determines the

temperature of the water.

Lid locked or will not open. • Press the Start/Pause button to stop your washer.

• It may take a few moments for the lid lock mechanism to disengage.

Does not drain and/or spin. • Check the fuse or reset the circuit breaker.

• Straighten the drain hoses. Eliminate kinked hoses. If there is a drain

restriction, call for service.

• Close the lid and press the Start/Pause button. For your safety, your

washer will not spin unless the lid is closed.

Load is too wet at the end

of the cycle.

• Use the High spin speed.

• Use high e ciency detergent to reduce over–sudsing.

• The Load is too small. Very small loads (one or two items) may

become unbalanced and not spin out completely.

Leaks water. • Make sure all hose connections are tight.

• Make sure the end of the drain hose is correctly inserted and secured

to the drainage system.

• Avoid overloading.

• Use high e ciency detergent to prevent over–sudsing.

Has excessive suds. • Use high e ciency detergent to prevent over-sudsing.

• Reduce the detergent amount for soft water, small or lightly soiled

loads.

• Non-HE detergent is NOT recommended.

Has an odor. • Check your Detergent . Excessive suds collect in nooks and crannies

and cause mold.

• Run cleansing cycles to sanitize the machine periodically. (Silver Care

or Sanitize Cycle or Self Clean)

• Dry the interior of your washer after the total cycle has ﬁ nished.

troubleshooting

WA7000M_EN.indd 32WA7000M_EN.indd 32 2/3/2017 11:13:28 AM2/3/2017 11:13:28 AM

English - 33

INFORMATION CODES

The Washer may display information codes to help you understand what is occurring with your Washer better.

CODE SYMBOL MEANING SOLUTION

Unbalanced load prevents washer

from spinning.

Redistribute the load, and then press the Start/

Pause button.

dC/dC1

The washer did not properly lock

the door.

Make sure the door is ﬁ rmly closed. Restart the

washer. If the code reappears, call customer

service.

dC3

Add Door did not lock.

Make sure the Add Door is ﬁ rmly closed. Restart

the washer. If the code reappears, call customer

service.

ddC

Add Door open while working

The washer does not drain. The

washer may detect a small clog

while draining.

1. Restart the washer.

2. Select the Spin Only cycle.

3. Press the Start/Pause button to drain the

water.

If the washer still does not drain, call customer

service.

Water is not being supplied to the

washer.

Make sure the water taps are open.

Make sure the water hoses are not clogged.

Make sure the water taps are not frozen.

Make sure the washing machine is operating with

su cient water pressure.

Make sure that the cold water tap and the hot

water tap are properly connected.

Clean the mesh ﬁ lter as it may be clogged.

4C2

The hot water was supplied from

the course washing the delicacy

clothes.

Make sure the cold water supply hose is ﬁ rmly

connected to the cold water tap.

If it is connected to the hot water tap, the laundry

may be deformed with some cycles.

Temperature sensor problem.

Restart the washer. If the code reappears, call

customer service.

Motor problem.

9C1/9C2

High/low voltage detected.

05 troubleshooting

WA7000M_EN.indd 33WA7000M_EN.indd 33 2/3/2017 11:13:28 AM2/3/2017 11:13:28 AM

English - 34

CODE SYMBOL MEANING SOLUTION

Water temperature control

problem. (Heater control)

Call customer service.

Water level problem

Water level sensor problem

The Water Level sensor is not

working properly

bC2

Jammed button.

Communication error

(SUB(sensor) PBA  MAIN PBA)

AC4

Communication error

(WIFI PBA  MAIN PBA)

AC3

Communication error

(DR Module  MAIN PBA)

AC5

Communication error

(LCD PBA  MAIN PBA)

AC6

Communication error

(Inverter PBA  MAIN PBA)

MEMS sensor problem.

System error.

Clutch Problem.

Sud

The washer has detected too many suds. The washer will stop operating until the

amount of suds has reduced. The washer will then resume normal operation.

Additional rinsing.

• Show additional rinsing in

sensing unbalance.

• Method of releasing the

display.

Any key input.

For any codes not listed above, call 1–800–726–7864 (1–800–SAMSUNG).

troubleshooting

WA7000M_EN.indd 34WA7000M_EN.indd 34 2/3/2017 11:13:28 AM2/3/2017 11:13:28 AM

English - 35

appendix

FABRIC CARE CHART

The following symbols provide garment care direction. The Clothing care labels include symbols for

washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures

consistency among garment manufacturers of domestic and imported items. Follow care label directions to

maximize garment life and reduce laundering problems.

Wash Cycle Special Instructions

Warning Symbols for

Laundering

Normal Line Dry/ Hang to Dry Do Not Wash

Permanent Press /

Wrinkle Resistant /

Wrinkle Control

Drip Dry Do Not Wring

Gentle/Delicates Dry Flat Do Not Bleach

Hand Wash Heat Setting Do Not Tumble Dry

Water Temperature**

High

No Steam (added to

iron)

Hot Medium Do Not Iron

Warm Low Dryclean

Cold Any Heat Dry Clean

Bleach

No Heat/Air Do Not Dry Clean

Any Bleach (when

needed)

Iron-Dry or Steam

Temperatures

Line Dry/ Hang to Dry

Only Non-Chlorine

(color-safe)

Bleach (when needed)

High Drip Dry

Tumble Dry Cycle Medium Dry Flat

Normal

Low

Permanent Press/

Wrinkle Resistant/

Wrinkle Control

Gentle/ Delicates

** The dot symbols represent appropriate wash water temperatures for various items. The temperature range for

Hot is 105° - 125 °F / 41° - 52 °C, for Warm 85° - 105 °F / 29° - 41 °C and for Cold 60° - 85 °F / 16° - 29 °C.

(Wash water temperature must be a minimum of 60 °F / 16 °C for detergent activation and e ective cleaning.)

The clothes washer can not ensure these temperatures because the actual temperature of the water entering

your washer depends on water heater settings and regional water supply temperatures. For example, cold

water entering the home in the northern states during winter may be 40 °F / 4 °C which is too cold for e ective

cleaning. In this situation, you will need to adjust the water temperature by selecting a warm setting, adding

some hot water to the MAX FILL line, or using your Washer’s heating option, if available.

06 appendix

WA7000M_EN.indd 35WA7000M_EN.indd 35 2/3/2017 11:13:28 AM2/3/2017 11:13:28 AM

English - 36

CYCLE CHART

Use this chart to set the best cycle and options for you laundry.

WA50M7450A*

(

: factory setting, : selectable)

Course

Functions

Temp. Spin Soil level

Hot Warm

Eco

Warm

Cool Cold High Medium Low No spin Heavy Normal Light

NORMAL

    

HEAVY DUTY

   

BRILLIANT WHITES

   

BEDDING/WATERPROOF

      

PERM PRESS

    

DEEP WASH

    

ACTIVE WEAR

     

QUICK WASH

   

DELICATES

   

RINSE+SPIN

 

SPIN

 

SELF CLEAN



Course

Options

Delay End Pre soak Extra rinse

NORMAL



HEAVY DUTY



BRILLIANT WHITES



BEDDING/WATERPROOF



PERM PRESS



DEEP WASH



ACTIVE WEAR



QUICK WASH

 

DELICATES

 

RINSE+SPIN

 

SPIN



SELF CLEAN



Temp. Spin Soil Level

Hot

Warm

Eco Warm

Cool

Cold

High

Medium

Low

No spin

Heavy

Normal

Light

appendix

WA7000M_EN.indd 36WA7000M_EN.indd 36 2/3/2017 11:13:28 AM2/3/2017 11:13:28 AM

English - 37

WA45M7050A*

(: factory setting, : selectable)

Course

Functions

Temp. Spin Soil level

Hot Warm

Eco

Warm

Cool Cold High Medium Low No spin Heavy Normal Light

NORMAL

    

HEAVY DUTY

   

BEDDING/WATERPROOF

     

PERM PRESS

    

DEEP WASH

    

QUICK WASH

   

DELICATES

   

RINSE+SPIN

 

SPIN

 

SELF CLEAN



Course

Options

Delay End Pre soak Extra rinse

NORMAL



HEAVY DUTY



BEDDING/WATERPROOF



PERM PRESS



DEEP WASH



QUICK WASH

 

DELICATES

 

RINSE+SPIN

 

SPIN



SELF CLEAN



Temp. Spin Soil Level

Hot

Warm

Eco Warm

Cool

Cold

High

Medium

Low

No spin

Heavy

Normal

Light

06 appendix

WA7000M_EN.indd 37WA7000M_EN.indd 37 2/3/2017 11:13:28 AM2/3/2017 11:13:28 AM

English - 38

HELPING THE ENVIRONMENT

• Your washer is manufactured from recyclable materials. If you decide to dispose of it, please observe

local waste disposal regulations. Cut o the power cord so that the appliance cannot be connected

to a power source. Remove the lid so that animals and small children cannot get trapped inside the

appliance.

• Do not exceed the detergent quantities recommended in the detergent manufacturers’ instructions.

• Use stain removal products and bleaches before the wash cycle only when necessary.

• Save water and electricity by only washing full loads (the exact amount depends upon the program used).

DECLARATION OF CONFORMITY

This appliance complies with UL2157.

SPECIFICATION

TYPE TOP LOADING WASHER

DIMENSIONS Div WA50M7450A* WA45M7050A*

Height

45.0" (114.4 cm) 43.9" (111.5 cm)

B. Width 27.0" (68.6 cm) 27.0" (68.6 cm)

C. Height with lid open

59.0" (150.0 cm)

58.1" (147.6 cm)

D. Depth 29.3" (74.4 cm) 29.3" (74.4 cm)

WATER PRESSURE 20-116 psi (137-800 kPa)

WEIGHT 64.0 kg 57.0 kg

SPIN REVOLUTION 800 rpm

POWER CONSUMPTION WASHING 120 V 700 W

SPIN 120 V 400 W

DRAIN 120 V 80 W

appendix

WA7000M_EN.indd 38WA7000M_EN.indd 38 2/3/2017 11:13:28 AM2/3/2017 11:13:28 AM

English - 39

warranty (U.S.A)

SAMSUNG WASHER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) year part and labor, Three (3) years stainless tub part (Part Only), Ten (10) years washing DD motor

part (Part Only).

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the United States. To receive warranty service, the purchaser must contact SAMSUNG for problem

determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized

service center. The original dated bill of sale must be presented upon request as proof of purchase to

SAMSUNG or SAMSUNG’s authorized service center. SAMSUNG will provide in-home service during the

warranty period at no charge, subject to availability within the contiguous United States. In-home service is

not available in all areas.

To receive in-home service, product must be unobstructed and accessible to the service agent. If service

is not available, SAMSUNG may elect to provide transportation of the product to and from an authorized

service center.

SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein,

with new or reconditioned parts or products if found to be defective during the limited warranty period

speciﬁ ed above. All replaced parts and products become the property of SAMSUNG and must be returned

to SAMSUNG. Replacement parts and products assume the remaining original warranty, or ninety (90)

days, whichever is longer.This limited warranty covers manufacturing defects in materials and workmanship

encountered in normal, noncommercial use of this product and shall not apply to the following: damage

that occurs in shipment; delivery and installation; applications and uses for which this product was not

intended; altered product or serial numbers; cosmetic damage or exterior ﬁ nish; accidents, abuse, neglect,

ﬁ re, water, lightning, or other acts of nature or God; use of products, equipment, systems, utilities, services,

parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied

or authorized by SAMSUNG that damage this product or result in service problems; incorrect electrical

line voltage, ﬂ uctuations and surges; customer adjustments and failure to follow operating instructions,

maintenance and environmental instructions that are covered and prescribed in the instruction book;

product removal and reinstallation; problems caused by pest infestations. This limited warranty does not

cover problems resulting from incorrect electric current, voltage or supply, light bulbs, house fuses, house

wiring, cost of a service call for instructions, or ﬁ xing installation errors. SAMSUNG does not warrant

uninterrupted or error-free operation of the product.

WA7000M_EN.indd 39WA7000M_EN.indd 39 2/3/2017 11:13:28 AM2/3/2017 11:13:28 AM

English - 40

EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS

OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR

PURPOSE.

NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT

TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS

OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE, OR INABILITY

TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED,

AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE

PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE.

WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS,

DAMAGE, OR INJURY TO PURCHASER AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR

PROPERTY ARISING OUT OF THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT. THIS LIMITED

WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS

PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation

of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This

warranty gives you speciﬁ c rights, and you may also have other rights, which vary from state to state.

To obtain warranty service, please contact SAMSUNG at:

Samsung Electronics America, Inc.

85 Challenger Road Ridgeﬁ eld Park, NJ 07660

1-800-SAMSUNG (726-7864)

www.samsung.com/us/support

Visits by a Service Engineer to explain functions, maintenance or installation

is not covered by warranty.

Please contact your Samsung call agent for help with any of these issues.

warranty (U.S.A)

WA7000M_EN.indd Sec11:40WA7000M_EN.indd Sec11:40 2/3/2017 11:13:29 AM2/3/2017 11:13:29 AM

English - 41

warranty (CANADA)

SAMSUNG WASHER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) year part and labor, Ten (10) years washing DD motor part (Part Only).

This limited warranty begins on the original date of purchase, and is valid only on products purchased

and used in the Canada. To receive warranty service, the purchaser must contact SAMSUNG for problem

determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized

service center. The original dated bill of sale must be presented upon request as proof of purchase to

SAMSUNG or SAMSUNG’s authorized service center. SAMSUNG will provide in-home service during the

warranty period at no charge, subject to availability within the Canada. In-home service is not available in all

areas.