Transcripción de documentos

CC-5 Natural Sound Mini Component System Active Servo Processing Speaker System 20 FM/10 AM Station Automatic Storing Capability Double Cassette Tape Deck with Automatic Reverse Function Tape “a” and “b” Continuous Playback Capability Automatic Synchronized Recording with CD Playback Automatic CD Editing Function for Recording to Tape 2-Way Speed Dubbing Dolby B/C Noise Reduction System 3-Mode Sound Processor Quick and Easy Direct Playback Function Multi-Use Timer/Sleep Timer Remote Control Capability Thank you for selecting this YAMAHA mini component system. This system is composed of TCD-CC5, A-CC5, K-CC5 and NS-CC5. Active Servo Technology CAUTION OWNER’S MANUAL RISK OF ELECTRIC SHOCK DO NOT OPEN CONTENTS Safety Instructions ..............Inside Front Cover Supplied Accessories .............................. 1 Precautions ..............................................2 Active Servo Technology .........................3 Names of Controls, Indicators and Rear Panel Parts ..........................................4–6 Remote Control Transmitter .................7–9 Preparation for Use ..........................10–11 Setting the Clock ....................................12 Compact Disc Operation ..................12–18 Tuner Operation ...............................19–21 Cassette Tape Operation .................22–24 Sound Control.........................................25 Recording .........................................26–30 How to Use the Built-in Timer...........31–33 Using External Units .........................34–35 Maintenance ...........................................35 Specifications .........................................36 Troubleshooting......................................37 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. IMPORTANT! Please record the serial number of this unit in the space below. • Explanation of Graphical Symbols Model: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. SAFETY INSTRUCTIONS 1 2 3 4 5 6 6A 7 8 9 10 11 12 13 14 15 A. B. C. D. E. 16 17 Read Instructions – All the safety and operating instructions should be read before the unit is operated. Retain Instructions – The safety and operating instructions should be retained for future reference. Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to. Follow Instructions – All operating and other instructions should be followed. Water and Moisture – The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. Carts and Stands – The unit should be used only with a cart or stand that is recommended by the manufacturer. A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. Heat – The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. Cleaning – The unit should be cleaned only as recommended by the manufacturer. Nonuse Periods – The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. Object and Liquid Entry – Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit. Damage Requiring Service – The unit should be serviced by qualified service personnel when: The power-supply cord or the plug has been damaged; or Objects have fallen, or liquid has been spilled into the unit; or The unit has been exposed to rain; or The unit does not appear to operate normally or exhibits a marked change in performance; or The unit has been dropped, or the cabinet damaged. Servicing – The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. Power Lines – An outdoor antenna should be located away from power lines. 18 Grounding or Polarization – Precautions should be taken so that the grounding or polarization is not defeated. 19 Outdoor Antenna Grounding – If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. EXAMPLE OF ANTENNA GROUNDING MAST ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) NEC – NATIONAL ELECTRICAL CODE Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. SPECIAL NOTES FOR FCC COMPOSITE DEVICE This device is a composite system. The digital device component may not cause harmful interference. FCC INFORMATION Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained. Remote control transmitter Indoor FM antenna 1 2 3 4 6 7 8 9 0 PROG CLEAR CALL TIME +10 BAND TUNER REPEAT 5 CD b Speaker cords a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT OFF - TAPE VOLUME + MW/LW(AM) loop antenna Batteries (size AA, UM/SUM-3, R6, HP-7) E-1 PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT ■ To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. STANDBY mode While the power is on, pressing the POWER switch (or the POWER button on the remote control transmitter) switches the unit to the STANDBY mode. (In this mode, the indicator above the POWER switch illuminates.) In this mode, main voltage is still present inside the unit. If you want to switch off the unit completely, disconnect the AC power plug from the wall socket. ■ This unit is equipped with the newly developed Active Servo Processing Speaker System. It is not designed for use with conventional speakers. Therefore, do not attempt to connect other speakers than the provided speaker system. ■ Choose the installation location of this unit carefully. Avoid placing it in direct sunlight or close to a source of heat. Also avoid locations subject to vibration and excessive dust, heat, cold or moisture. Keep it away from sources of hum such as transformers and electric motors. NOTE Please check the copyright laws in your country to record from records, compact discs, radio, etc. Recording of copyright material may infringe copyright laws. ■ Do not operate this unit upside-down. It may overheat, possibly causing damage. ■ Never open the cabinet. If something drops into the set, contact your dealer If this unit’s operation freezes or display indications are incorrect First disconnect the AC supply lead from the wall AC outlet, and then press the RESET button on the rear of this unit at least for one minute. This operation “resets” the internal microcomputer which controls this unit. However, this operation will also erase all memorized broadcasting stations. To store stations again, follow the methods described on page 19–20. ■ Do not place CD or other objects on top of this unit. ■ Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wire itself. ■ Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. ■ Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. WARNING ■ To prevent lightning damage, disconnect the AC power plug and disconnect the antenna cable when there is an electrical storm. To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture. ■ Do not plug the AC power plug to the wall socket before you finish all connections. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. ■ Never allow metallic items (e.g. screwdrivers, tools, etc.) to come near the cassette deck’s record/playback head assembly in this unit. Doing so may not only scratch or damage the head’s mirrorsmooth finish, it may change the magnetic characteristics of the heads, causing a deterioration in reproduction performance quality. DANGER Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. ■ Although the cassette deck’s record/playback heads used in this unit are high quality heads with outstanding reproduction characteristics, they can become dirty through the use of old tapes or from dust accumulation over time. This can have a serious effect on reproduction quality. Clean the heads regularly with one of the commonly available head cleaners or with cleaning solutions. CAUTION 1 Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. ■ The voltage to be used must be the same as that specified on this unit. Using this product with a higher voltage than that which is specified is dangerous and may result in a fire or other type of accident causing damage. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified. CAUTION 2 As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. ■ Sudden temperature changes and storage or operation in an extremely humid environment may cause condensation inside the cabinet. Condensation can cause the unit to malfunction. Follow the procedure below to eliminate condensation. • • • Laser Diode Properties Material: GaAlAs Wavelength: 780nm Emission Duration: continuous Laser Output: max. 44.6µW* * This output is the value measured at a distance of about 200mm from the objective lens surface on the Optical Pick-up Block. • • • • CD pickup Leave the power on with no disc in the unit until normal playback is possible (about 1 hour). Tape head Leave the power on with no cassette in the unit until normal playback is possible (about 1 hour). Note If condensation forms on the tape head, foreign matter may accumulate during use. Remote control Wipe off condensation on the transmitter window with a soft cloth before operating the unit. ■ The sound level at a given volume setting depends on a combination of speaker efficiency, location and may other factors. Care should be taken to avoid exposure to sudden high levels of sound, which may occur when turning on the unit with the volume control setting at high, and to continuous high levels of sound. E-2 ACTIVE SERVO TECHNOLOGY Highamplitude bass sound Cabinet Air woofer (Helmholtz resonator) Port Active Servo Processing Amplifier Signals Negative-impedance output drive Signals of low amplified Thus it is this problem that is resolved through the employment of a design in which the amplifier functions to supply the signals. If the electrical resistance of the voice coil is reduced to zero, the movement of the speaker unit would become linear with respect to signal voltage, and, to accomplish this, a special negative-impedance output-drive amplifier for subtracting output impedance of the amplifier is used. By employing negative-impedance drive circuits, the amplifier is able to generate precise, low-amplitude low-frequency waves with superior damping characteristics, and these waves are then radiated from the cabinet opening as highamplitude signals. The system can, therefore, by employing the negative-impedance output drive amplifier and a speaker cabinet with the Helmholtz resonator, reproduce an extremely wide range of frequencies (28 Hz – 20 kHz) with amazing sound quality and less distortion. The features described above, then, are combined to be the fundamental structure of the Active Servo Technology. The theory of the Active Servo Technology is based upon two major factors, the Helmholtz resonator and negativeimpedance drive. Active Servo Processing speakers reproduce the bass frequencies through an “air woofer”, which is a small port or opening in the speaker’s cabinet. This opening is used instead of, and performs the functions of, a woofer in a conventionally designed speaker system. Thus, signals of low amplitude within the cabinet can, according to the Helmholtz resonance theory, be output from this opening as waves of great amplitude if the design is such that the size of the opening and the volume of the cabinet are in the correct proportion to satisfy a certain ratio. In order to accomplish this, moreover, the amplitudes within the cabinet must be both precise and of sufficient power because these amplitudes must overcome the “load” presented by the air that exists within the cabinet. E-3 NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS CD Player Section 1 2 4 3 7 8 6 5 9 PROGRAM TOTAL REMAIN TIME OVER AUTO EDIT RANDOM A 9 10 8 2 3 6 1 4 5 7 11 12 13 14 15 16 17 18 19 20 OVER REPEAT B 10 11 12 13 14 15 18 19 17 16 20 21 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. AUTO EDIT Indicator TIME OVER Indicator Track Number Indicator PROGRAM Indicator TOTAL Time Indicator REMAINING Time Indicator Minutes and Seconds Indicator Pause Indicator: Play Indicator: Tape Side Indicators Music Schedule Indicator Music Schedule OVER Indicator RANDOM Play Indicator REPEAT Indicator 15. 16. 17. 18. 19. 20. 21. 22. RANDOM Play Button Stop Button: Play Button: Disc Table Open/Close Button: EDIT Button Skip Buttons: / Auto Tape Edit Buttons 22 Tuner/Timer Section 23 25 24 MHz kHz MEMORY AUTO ST STEREO 26 27 28 29 TIMER SLEEP ON TIME 30 31 32 33 35 36 37 38 39 40 34 41 E-4 23. 24. 25. 26. 27. 28. 29. 30. 31. Preset Number Indicator Band Indicator Station Frequency Indicator MEMORY Indicator AUTO ST Indicator FM STEREO Indicator TIMER Set Indicator ON TIME Indicator SLEEP Indicator 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. AUTO MEMORY Button BAND Selector Button TUNER PRESET Buttons: / DISPLAY Button TIMER Button SLEEP Button MEMORY/TIME ADJUST Button FM MODE/CLEAR Button TUNING Down/HOUR Button: TUNING Up/MINUTE Button: NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS Amplifier Section 42 43 44 49 45 46 50 47 42. 43. 44. 45. 46. 47. 48. 49. 50. POWER Switch STANDBY Indicator BASS Tone Control TREBLE Tone Control BALANCE Control INPUT Selector and Indicators VOLUME Control/Indicator PHONES Jack SOUND PROCESSOR Program Selector and Indicators 51. Remote Control Sensor 48 51 Tape Deck Section 52 53 54 55 56 57 58 59 60 61 62 63 64 66 67 68 69 70 71 65 72 E-5 ■ 52. 53. 54. 55. 56. 57. 58. Controls for Tape “a” Tape “a” Cassette Compartment EJECT Button Fast Wind Button: Play Button and Indicator: Stop Button: Play Button and Indicator: Fast Wind Button: ■ 59. 60. 61. 62. 63. 64. 65. Controls for Tape “b” Fast Wind Button: Play Button and Indicator: Stop Button: Play Button and Indicator: Fast Wind Button: EJECT Button Tape “b” Cassette Compartment ■ 66. 67. 68. 69. 70. 71. 72. Common Controls for Tape “a” and “b” REVERSE MODE Switch DOLBY NR Switch DUBBING Buttons and Indicators PAUSE Button REC Button Record Indicator TIMER Switch NAMES OF CONTROLS, INDICATORS AND REAR PANEL PARTS Rear Panel of Tuner/CD Player Section 1. 2. 3. 4. System Control Connector Antenna Terminals RESET Button FREQUENCY STEP Switch (General model only) FREQUENCY STEP switch (General model only) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC supply lead of this unit from the AC outlet. (U.S.A., Canada and General models) Rear Panel of Amplifier Section (U.K., Australia and Europe models) 5. 6. 7. 8. 9. 10. 11. System Control Sockets SPEAKERS Terminals DAT Terminals PHONO Terminals and GND Terminal AUX Terminals VOLTAGE SELECTOR (General model only) AC Supply Lead VOLTAGE SELECTOR (General model only) The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240V AC, 50/60 Hz. Rear Panel of Tape Deck Section 12. System Control Connector 13. System Control Socket Speaker Section 14. AST Port 15. Speaker Terminals E-6 REMOTE CONTROL TRANSMITTER Names of controls 1 1 2 3 4 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 2 3 9 10 4 5 6 7 8 REPEAT CD BAND TUNER 11 b 12 a 13 ■ 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. CD Control Buttons Remote Control Transmitter Window Track Number Input Buttons PROGRAM Button CLEAR Button CALL Button Search Buttons: / REPEAT Button Stop Button: TIME Display Selector Button Open/Close Button: Skip Buttons: / CD Call Button Play Button: Pause Button: ■ 15. 16. 17. Tuner Control Buttons Tuning Up/Down Buttons BAND Selector Button TUNER Call Button 14 HALL JAZZ CLUB ROCK CNCT POWER AUX DAT 15 OFF - TAPE VOLUME + 16 17 BAND TUNER OFF TAPE b a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME + E-7 REMOTE CONTROL TRANSMITTER Tape “b” ■ Tape Control Buttons 18. Record/Pause Button: 19. Fast Wind Button: 20. Play Button: 21. Stop Button: 22. Play Button: 23. Fast Wind Button: 24. Fast Wind Button: 25. Play Button: 26. Stop Button: 27. Play Button: 28. Fast Wind Button: 29. TAPE Call Button 19 20 21 22 23 BAND TUNER OFF TAPE 18 Tape “a” b a 28 24 HALL JAZZ CLUB ROCK CNCT 29 25 26 27 REPEAT 30. POWER Switch 31. AUX Call Button 32. DAT Call Button (or PHONO Call Button for U.K., Australia and Europe models) 33. Sound Processor Program Selectors 34. Sound Processor OFF Button 35. VOLUME Down (–)/Up (+) Buttons CD BAND TUNER b 33 a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT OFF TAPE 34 30 - VOLUME + 35 31 32 E-8 REMOTE CONTROL TRANSMITTER Loading the batteries for the remote control transmitter 1 2 Remove the battery compartment cover. 3 Replace the battery compartment cover. Insert 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or equivalent) into the battery compartment. * Placing the batteries the wrong way round will cause malfunction. Precautions for battery use Insert the batteries according to the direction indicated in the battery compartment. Replace all batteries with new ones at the same time. Remove the batteries if they are weak or if the unit is not in use for long periods. Don’t mix normal batteries with rechargeable batteries. • • • • Proper use of the remote control transmitter Aim (within the range of 30° with no obstacles) the remote control transmitter at the remote control sensor and operate as shown. Notes concerning use • Replace the batteries if control distance decreases or operation becomes unstable. • Periodically clean the transmitter window on the remote control transmitter and the sensor on the main unit with a soft cloth. • Exposing the sensor on the main unit to strong light (especially an inverter type of fluorescent lamp etc.) may interfere with operation. Change the lighting or the direction of the unit. • Keep the remote control transmitter away from moisture, excessive heat, shock and vibrations. • The remote control transmitter’s usable range is within 0.2m (8”) and 6m (20’) away from the sensor. E-9 PREPARATION FOR USE Placing the system Tuner/CD player A Left speaker Right speaker Amplifier B Left speaker Notes • If the system is put in a rack, allow a space of a least 3 cm (1-3/16”) above and 10 cm (4”) at the back of the unit. • Disconnect the AC supply lead from the AC outlet before connecting or disconnecting any component. • Be careful not to let the connection cords touch the radiator plates on the rear of the amplifier. Deck Tuner/CD player Amplifier Place this system in either the way of A or B figured at left. A: Be sure to place the Tuner/CD player on the top, the Deck at the bottom and the Amplifier between them. B: Be sure to place the Tuner/CD player on the Deck, and the Amplifier at the left of them. Right speaker Deck Antenna connection (1) Supplied FM antenna Connect the FM antenna wire to the corresponding terminal and direct the FM antenna wire to the direction where the strongest signal can be received. (2) Supplied MW/LW (AM) loop antenna Connect the MW/LW (AM) loop antenna wire to the corresponding terminals. Position the MW/LW (AM) loop antenna for optimum reception. Place the MW/LW (AM) loop antenna on a shelf etc., or install it on the rack or wall with screws (not supplied). 15 m (49 feet) Notes • When static is still heard even after adjusting the position of the MW/LW (AM) loop antenna, try reversing the connection (right to left). • Do not place the MW/LW (AM) loop antenna on the unit. It will result in noise generation, since the unit is equipped with digital electronics. Place the MW/LW (AM) loop antenna away from the unit. 7.5 m (25 feet) Earth rod (3) External FM antenna Use an external FM antenna instead of an indoor FM antenna if you need better reception. Consult your dealer. (4) External MW/LW (AM) antenna Use an external MW/LW (AM) antenna if you need better reception. Consult your dealer. or Note When using an external MW/LW (AM) antenna, be sure to keep the wire of the MW/LW (AM) loop antenna connected. E-10 PREPARATION FOR USE Speaker connection Altavoz derecho Connect each speaker wire to the SPEAKERS terminals as shown. (Black wire with white line → plus (+) terminal, black wire → minus (–) terminal) Altavoz izquierdo Cautions • Do not let the bare speaker wires touch each other as this could damage the amplifier and/or speakers. • When connecting the speakers to the unit, be sure to connect the speaker wires properly. Do not mistake the right channel for the left channel and the plus (+) terminal for the minus (–) terminal. • Do not connect these SPEAKERS terminals to speakers other than the provided speaker system. System connection • • • Connect the red connector to the red socket. Connect the white connector to the white socket. Connect the black connector to the black socket. How to disconnect the system connector Grasp both sides of the connector to disconnect the connector. Connecting the AC supply lead • • To an AC outlet E-11 After connecting the speakers and system connectors, plug the AC supply lead into a convenient AC outlet. Unplug the AC supply lead from the AC outlet if the unit is not to be used for a long period of time. SETTING THE CLOCK 1 1 While the station frequency indicator on the tuner or the “ON TIME” indicator is lit, press the DISPLAY button to display the time. 2 While pressing the TIME ADJUST button, press the HOUR button and set the hour. * Press the HOUR button once to advance the time by 1 hour. Press and hold to advance continuously. 3 While pressing the TIME ADJUST button, press the MINUTE button and set the desired time. * Press the MINUTE button once to advance the time by 1 minute. Press and hold to advance continuously. * The hour setting will not advance even if minutes advance from “59” to “00”. 4 Release the TIME ADJUST button to start the clock at the correct time. * The clock starts operating from “0” seconds. (Seconds are not displayed.) DISPLAY 2 TUNING HOUR MEMORY MINUTE FM MODE Changes. TIME ADJ CLEAR 3 TUNING HOUR MEMORY MINUTE In the event of a power failure or when the AC supply lead is disconnected. The clock display will go out. When the AC power supply is resumed, the clock display will flash on and off to indicate that the time must be reset. FM MODE Changes. TIME ADJ CLEAR 4 TUNING HOUR MINUTE MEMORY FM MODE TIME ADJ CLEAR Europe model uses an “00:00” 24-hour display. COMPACT DISC OPERATION Care of compact discs Compact discs are fairly resistant to damage, however mistracking can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your CD collection and player. • Do not write on either side of the disc, particularly the nonlabel side. Signals are read from the non-label side. Do not mark this surface. • Keep your discs away from direct sunlight, heat and excessive moisture. • Always hold the CDs by the edges. Fingerprints, dirt or water on the CDs can cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the centre, along the radius. E-12 COMPACT DISC OPERATION CD playback 2,4 1 2 3 Select the CD position. 4 Press the open/close button to close the disc table. * The total number of tracks and the total playing time will be displayed for several seconds. * The music schedule will be displayed only for the number of tracks on the disc. * If the compact disc contains more than 21 tracks, the “OVER” indicator will light up on the music schedule. 5 Press the open/close button to open the disc table. Place a disc on the table, label side up. * 8 cm (3”) discs may be played without an adaptor. Total number of tracks Remaining playing time for first track Total playing time REMAIN TOTAL 2 1 11 12 3 4 5 6 7 8 9 10 2 1 11 12 3 4 5 6 7 8 9 10 Music schedule 5 1 POWER Press the play button to start playback from track 1. * The “ ” indicator will appear and playback will begin. As the playback of each track on the music schedule is finished, that track number will go out. Direct playback 1 1 2 3 4 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 BAND TUNER OFF TAPE REPEAT CD b a POWER HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME If a compact disc is already in the disc table, just press the play button to automatically turn on the power and start playback. 2,4 1 5,2 2 To interrupt playback 1 Press the pause button. * The “ ” indicator will light up. 2 Press the play button to resume playback from the same point. + To stop playback Press the stop “ ” button. To switch the unit off after use Set the unit to the STANDBY mode by pressing POWER switch. (The indicators will go off except for the STANDBY indicator and the current time display.) E-13 COMPACT DISC OPERATION Precautions • If the disc is damaged, dirty or loaded upside down, the display will show error signs as follows: * “no disc” is displayed. * The total track number or “01” is not displayed. Clean, replace or load the disc properly. • If TV or radio interference occurs during CD operation, move the unit away from the TV or radio. • Subjecting the unit to shock or vibration can cause mistracking. • Playing some compact discs at high volume can cause mistracking. In this case, listen at lower volume. • Do not push the disc table while it is moving. • Press the open/close button if your finger, a disc or other object is caught by the table. (The table closing operation will stop after 4 seconds even if the open/close button is not pressed. At this time, “Er 0:00” appears in the display.) • If the power fails while the table is open, wait until the power supply returns or gently push the table manually to close it. • The temperature range for playing compact discs is recommended to be 5°C (41°F) – 35°C (95°F). Direct-selection play 1 2 3 4 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 1 2 3 4 5 6 7 8 9 0 By using the track number input buttons on the remote control transmitter, any track you wish to listen to can be played directly. Use the track number input buttons to select the desired track number. Play will begin automatically. +10 REPEAT A. For example, to choose selection 12 (1) Press the “+10” button. (2) Within 3 seconds, press “2” button. CD BAND TUNER b B. For example, to choose selection 20 (1) Press the “+10” button. (2) Within 3 seconds, press the “+10” button again. (3) Within 3 seconds, press the “0” button. a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT OFF - TAPE VOLUME + Note A track number higher than the number of tracks on the disc cannot be selected. Also, if a higher track number is selected while the disc table is open, play will begin from track 1 when the disc table is closed. E-14 COMPACT DISC OPERATION Skip search 2 The beginning of any track can be found automatically. 1 2 1 2 3 4 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 REPEAT 1 CD BAND TUNER OFF TAPE b a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME Press the button to forward or button to reverse through the CD. * The “ ” indicator flashes while searching for the track beginning. * If the button or button is pressed repeatedly during playback, playback will begin from the beginning of the track shown in the track number indicator. * This function can also be performed while the unit is stopped. Press the play button when your desired track number appears in the track number display. Playback will begin from the beginning of the track. Note This function will be performed forward or backward from any point on the disc. However, it will not move forward during playback of the final track. 2 + Load a disc and begin playback. Manual search 1 2 1 2 3 4 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 BAND TUNER OFF TAPE REPEAT CD b a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME Begin playback. Press and hold the button to advance play rapidly, and the button to reverse play rapidly. * The sound can be heard (although slightly garbled) during manual search in either direction. This is convenient for locating a precise position within a track, or for reviewing the contents quickly. * Manual search proceeds at twice the normal playback speed for several seconds, and then the speed will become faster. Notes • Manual search can also be performed while disc play is paused. • Manual search is not possible during random play. • If the end of the disc is reached while searching, the “End” indicator lights and CD operation is paused. Press the stop button to stop CD operation. + E-15 COMPACT DISC OPERATION Program play You can program up to 20 tracks in any desired order. 2 1 2 3 4 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 3 1 2 Load a disc and close the disc table. 3 Use the track number input buttons to select the desired track number. * The selected track number will be displayed. * The programmed playback order and the total play time of the programmed tracks will be automatically displayed, and only those track numbers will appear in the music schedule. 5 REPEAT When in the stop mode, press the PROGRAM button to prepare for programming. * The “PROGRAM” indicator will flash. CD BAND TUNER OFF TAPE b a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - + VOLUME * For example, to choose selection 12 (1) Press the “+10” button. (2) Within 3 seconds, press the “2” button. Playback order PROGRAM 2 12 1 4 Repeat step 3 for any other track. Up to 20 tracks can be programmed. 5 Press the play button to start playback of programmed selections. Total playing time TOTAL Notes It is also possible to program a sequence of tracks while looking at the list of tracks on the surface of the disc before closing the disc table. • During playback or pause, programming is not possible. 10 3 • Music schedule To check the program data 1 2 3 4 6 7 8 9 0 PROG CLEAR CALL TIME +10 REPEAT Press the CALL button while the disc is stopped to review the order of the programmed sequence before playback begins. * While the playback order and track numbers are displayed, the track numbers on the music schedule will also flash on and off in the same order. 5 CALL Press the CALL button during playback or pause to check the number of the next track to be played. CD BAND TUNER CLEAR b To cancel the programmed sequence a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT OFF - Press the CLEAR button while the disc is stopped and the “PROGRAM” indicator is lit. * To cancel the last programmed track during programming, press the CLEAR button when the “PROGRAM” indicator is flashing. TAPE VOLUME + Notes • Opening the disc table automatically cancels the programmed sequence. • Programming and cancelling are not possible during playback or pause. Playback order PROGRAM 1 2 12 Track number TOTAL 3 10 Music schedule E-16 COMPACT DISC OPERATION Repeat play An entire disc, a single track or a programmed sequence can be continuously repeated. To repeat an entire disc 1 2 3 4 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 2,3 3 1,2 2 REPEAT 1 Press the REPEAT button. * The “REPEAT” indicator will light up. 2 Press the play button. CD BAND TUNER OFF TAPE To repeat a programmed sequence b a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME 1 Program a sequence of up to 20 tracks. (Refer to the “Program play” on the previous page for the programming method.) 2 Press the REPEAT button. * The “REPEAT” indicator will light up. 3 Press the play button. + To repeat a single track 2 1 11 12 3 4 5 6 7 8 9 1 Program a single track. (Refer to the “Program play” on the previous page for the programming method.) 2 Press the REPEAT button. * The “REPEAT” indicator will light up. 3 Press the play button. 10 REPEAT To cancel the repeat play Press the REPEAT button again. (The “REPEAT” indicator goes out.) E-17 COMPACT DISC OPERATION Random play The tracks on the disc can be played in a random order. 1 2 RANDOM 3 1 2 Load a disc and close the disc table. Press the RANDOM button to begin random play. * The “RANDOM” indicator will light up. * As the tracks to be played are selected, the track numbers “[1]”, “[2]”, “[3]” ... “[20]” in the music schedule will flash on and off and the track number display will change accordingly. To cancel the random play Press the play button. The “RANDOM” indicator goes out. Notes • When using random play or repeat play, be sure to press the stop button, or switch off the power when you have finished listening. Otherwise, the CD(s) will be played endlessly. • While programmed tracks are being played, random play is not possible. Switching the time display Each time the TIME button is pressed, the display will change as described below. TIME 2 3 4 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 REPEAT [Example] When the second track is being played back. (Refer to the illustration on the left.) ➀ 1 2 11 12 3 4 5 6 7 8 9 10 ➀ The elapsed play time for each track will be displayed. CD BAND TUNER 2 11 12 b ➁ REMAIN ➁ 3 4 5 6 7 8 9 10 a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT OFF - ➂ TAPE VOLUME + TOTAL ➂ 2 11 12 3 4 5 6 7 8 9 10 ➃ * 8 seconds have passed since the beginning of the second track. The remaining play time for the current track will be displayed. * 2 minutes and 58 seconds remain till the end of the second track. The total play time up to the current track will be displayed. * 8 minutes and 16 seconds have passed since the beginning of the first track. The total remaining play time from the point being played at that time will be displayed. * 41 minutes remain till the end of the disc. TOTAL REMAIN ➃ 2 11 12 3 4 5 6 7 8 9 Notes During random play, the elapsed play time for each track will be displayed, and the display cannot be switched. When a disc that has 21 or more tracks is used, “--:--” will be displayed in the following cases: * When an attempt is made to display a track number 21 or higher by using the button when the disc is stopped. * When an attempt is made to display the remaining time while a track whose number is 21 or higher is being played back. * When you program a track number 21 or higher . * When the total play time exceeds 100 minutes. 10 • • E-18 TUNER OPERATION You can store up to 30 stations (20 FM stations and 10 AM (LW or MW) stations) and recall them together with their FM reception mode (stereo or mono), at the push of a button. 2 3 Auto scan memory By this method, the unit will store stations with strong signals automatically (for FM and AM (LW or MW) respectively). 1 1 2 3 4 6 7 8 9 0 PROG CLEAR CALL TIME +10 BAND TUNER OFF TAPE REPEAT CD a 1 2 HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME Select the TUNER position. 3 Press the AUTO MEMO button. * The “MEMORY” indicator will flash. * After auto scan memory is finished, the “MEMORY” indicator goes out, and you can hear the broadcast station which was stored last into memory. * If fewer than 20 FM stations or 10 AM (LW or MW) stations have been stored in memory, auto scan memory will stop at the highest frequency and this unit will turn into receiving mode. * If auto scan memory is performed again though broadcasting stations have been already stored, the previous contents are erased. Select the desired frequency band. [FM or AM (LW or MW)] Note The auto scan memory function may be affected by radio interference generated by electric equipment. For example, home computers, facsimiles, etc. If you have difficulty using the auto scan memory, move the unit away from electric equipment and adjust the position of the antenna to minimize the interference. If you cannot minimize the interference, please use the manual memory function as described below. 5 b 1 2 + “AM” is for U.S.A., Canada, Australia and General models. “MW/LW” is for U.K. and Europe models. E-19 TUNER OPERATION Manual memory 3,5 When auto scan memory does not function due to a weak signal, frequencies are deviated due to a strong signal, or you want to change the memory contents, perform the following operation. 2 4 1 2 Perform steps 1 – 2 of the “Auto scan memory” section. Use the TUNING ( desired station. or ) button to tune into the Auto tuning When the TUNING ( or ) button is pressed for more than 0.5 second and then released, the tuning stops at the first receivable broadcast station. Manual tuning Press the TUNING ( or ) button repeatedly to adjust the frequency display to the frequency of the desired station. E-20 3 Press the MEMORY button, so that the display’s “MEMORY” indicator flashes. 4 Press the TUNER PRESET ( or ) button until the preset number to be programmed appears in the display. 5 Press the MEMORY button to store that station in the selected station preset number memory. * 20 FM stations can be preset (preset channels 1 through 20). * 10 AM (LW or MW) stations can be preset (preset channels 1 through 10). (There are no presets 11 through 20 for AM (LW or MW) stations.) 6 Repeat steps 1 – 5 to set the other preset stations, or to change a preset station. TUNER OPERATION 2 4 To recall a memorized station 3 1 2 Select the TUNER position. 3 Press the TUNER PRESET ( or ) button to recall the desired preset station number. The caption FM or AM (LW or MW) and a frequency will appear in the display. 4 To set to FM stereo mode, press the FM MODE button so that the “STEREO” indicator on the display lights up. If the reception is poor, press the FM MODE button so that the “STEREO” indicator goes out. * The “AUTO ST” indicator lights up when an FM broadcast is in stereo. * Please note that when the unit is being tuned in the FM stereo mode, interim station noise as well as weak stations are suppressed. Only in the FM monaural mode, weak and noisy stations can be received. 1 Select the desired frequency band. [FM or AM (LW or MW)] To switch the unit off after use 1 2 3 4 Set the unit to the STANDBY mode by pressing the POWER switch. (The indicators will go off except for the STANDBY indicator and the current time display.) 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 3 REPEAT Notes • Memory recalls the last station received even after changing the BAND selector button or setting the unit to the STANDBY mode. • After a power failure that lasts for some time, the contents of the memory will be lost. When power is restored, store your selections in memory again. (For power failures of just a few hours, the contents of the memory will not be lost.) CD BAND TUNER OFF TAPE b a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME 1 2 + To clear all memorized stations To clear all the memory contents or when the display is incorrect: 3 1 2 3 E-21 Set the unit to the STANDBY mode. Disconnect the AC supply lead from the AC outlet. Press the RESET button for at least 60 seconds. CASSETTE TAPE OPERATION General information • • • • • • • Detection hole Tab • Do not use C-120 tapes, tapes with internal reels or poorquality tapes, since they can cause malfunctions. Before loading a tape into the cassette compartment, tighten the slack tape with a pen or pencil. Tapes have removable tabs which prevent accidental recording or erasing from taking place. Removing the tab on the top left protects the side facing you from erasure. Cover the tab holes with adhesive tape to erase or record again. This deck is a Double Cassette Deck with Automatic Reverse Function. Tape “a”: Playback only. Tape “b”: Playback or recording. This deck features an auto tape selector. Just load the tape, and the tape formula being used will be sensed automatically. This unit can playback metal tapes as well as normal or chrome tapes, however recording cannot be done on metal tapes only. When covering erasure prevention tab holes, do not cover the chrome and metal detection holes. Otherwise, the deck will treat tape as normal tape. Do not press the EJECT button during playback or recording. Tape “a” or tape “b” playback 1 3 3 1 2 Select the TAPE position. 3 Load the cassette into the tape “a” or tape “b” cassette compartment. 4 Set the DOLBY NR switch to B or C if the tape has been recorded with Dolby noise reduction, and to OFF if Dolby NR was not used. * For selection of the Dolby B or C position, refer to the “Dolby B and C Type Noise Reduction” on page 24. 5 Set the REVERSE MODE switch as desired. (b) (a) 4 Open the tape “a” or tape “b” cassette compartment by pushing the EJECT button. The REVERSE MODE switch can be operated before or during playback, and changes tape playback as follows: 2(a) 5 6(a) 6(b) 2(b) 6 E-22 Side A only Side A → Side Side A → Side B Continuous play B Side B only Side B only Side B → Side A Continuous play Press the play button to listen to side A, or the play button for side B. CASSETTE TAPE OPERATION Direct playback If a cassette tape is already in the cassette compartment, just press the play button to automatically turn on the power and start playback. Note While the INPUT selector is rotating to select the TAPE position before playback starts, do not press the EJECT button. To stop playback Press the stop button. Note When removing the cassette tape, press the stop and then open the cassette compartment. button, To switch the unit off after use Set the unit to the STANDBY mode by pressing the POWER switch. (The indicators will go off except for the STANDBY indicator and the current time display.) Winding the tape 1 2 3 First press the stop button. Next press the or button to wind the tape. Press the stop button to stop. Searching for the beginning of a desired selection (a) Carry out the following operation during playback to find the beginning of a desired selection on the tape. (b) • • 1 2 3 4 6 7 8 9 0 TIME +10 BAND TUNER PROG CLEAR CALL REPEAT 5 Notes This function may not work for tapes with • Material with long pauses or quiet passages. • Low recording levels or excessive noise. • Pauses of less than 3 seconds between selections. CD (b) b a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT OFF - TAPE VOLUME To listen to the same selection, press the or button in the direction opposite from that of current playback. To listen to the next selection, press the or button in the same direction as that of current playback. + (a) E-23 CASSETTE TAPE OPERATION Continuous playback 1 1 Load the tapes into the tape “a” and tape “b” cassette compartments. 2 Set the REVERSE MODE switch as desired. The REVERSE MODE switch can be operated before or during playback, and changes tape playback as follows: 2 3(a) 3(b) Tape “a” Side A → B → Tape “b” Side A → B Tape “a” Side A → B → Tape “b” Side A →B Continuous play Tape “a” Side B → Tape “b” Side A → B Tape “a” Side B → Tape “b” Side A → B → Tape “a” Side A Continuous play <Tape “a”> <Tape “a”> 1 2 3 4 6 7 8 9 0 PROG CLEAR CALL TIME +10 BAND TUNER OFF TAPE REPEAT 5 3 CD Press the play button to listen to side A, or the play button for side B. 3(b) b a 3(a) HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME + Dolby B and C Type Noise Reduction With cassette tapes, the most noticeable form of noise is high frequency hiss. To reduce this hiss noise, this unit has been equipped with a newly developed Dolby C noise reduction system in addition to its conventional Dolby B NR. Either type of noise reduction may be selected with the switch provided. Dolby B NR has a noise reduction effect of about 10 dB in the high frequency range. The corresponding figure with Dolby C NR is about 20 dB, but this is over the entire range where the human ear is most sensitive to noise (2 kHz to 8 kHz). Also, Dolby C NR has the same noise reduction effect at both high and low signal levels. In addition, Dolby C NR improves the tape’s MOL (Maximum Output Level). Dolby noise reduction is a 2 part process that acts both on recording and playback; be sure that the noise reduction button is set to the same position on record and play. * Noise in the source material cannot be reduced with the Dolby NR system. Dolby and the double D mark are trademarks of Dolby Laboratories Licensing Corp. Dolby noise reduction system manufactured under license from Dolby Laboratories Licensing Corp. E-24 SOUND CONTROL Volume VOLUME Front panel operation Rotate the VOLUME control towards 10 to increase the volume, and towards 0 to decrease the volume. 5 4 6 3 7 - VOLUME + Remote control operation Press the VOLUME + button to increase the volume and the VOLUME – button to decrease the volume. 8 2 I 9 0 10 Balance BALANCE Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused from the speaker settings or the listening room condition. Turn this clockwise to emphasize the right and counterclockwise for the left. L R Tone TREBLE BASS BASS TREBLE - + - + : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. Sound processor SOUND PROCESSOR JAZZ ROCK CLUB CONCERT If desired, select your favorite sound processor program by pressing the SOUND PROCESSOR button. The indicator below the name of the selected program illuminates. (No illumination shows that the sound processor is off.) For each program feature, refer to the following explanation. HALL HALL The ideal program for listening to opera or orchestra music. This program creates an expansive, large hall ambience. The apparent listening position is in the center of the hall rather than in front of the stage. JAZZ CLUB This program creates an ambience of intimate jazz club with a low ceiling and a stage located in a corner. You feel so close to music by this program. ROCK CONCERT E-25 This program suits to rock music. A big, powerful sound is reproduced lively and dynamically. RECORDING • • • When recording important selections, be sure to make a preliminary test to ensure that the desired material is being properly recorded. The automatic recording level control circuit automatically controls the level of the input signal used for recording. Adjusting the VOLUME, BALANCE, TREBLE and BASS controls and selecting any SOUND PROCESSOR program have no effect on the recorded sound. Recording from the CD player (CD Synchronized Recording System) 1 6,2 2 1 2 Select the CD position and load the CD to be recorded. 3 When recording with the Dolby NR system, set the DOLBY NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the “Dolby B and C Type Noise Reduction” on page 24. 4 Set the REVERSE MODE switch to to record on only one side, or to for continuous recording on both sides. 5 Press the REC button. * The indicator next to the REC button will light up and the play indicator flash. 6 Press the play button of the CD. * Before CD playback begins, recording automatically begins on side A of the tape. Load a tape into the tape “b” cassette compartment. * Wind past the beginning part of the tape on which recording can not be performed. To stop recording temporarily 1 2 4 3 5 2 Press the pause button of the CD. Press the play button of the CD to resume recording. To stop recording Press the stop button of the tape deck. (At this time, CD playback does not stop.) 1 2 3 4 6 7 8 9 0 PROG CLEAR CALL TIME +10 REPEAT 5 5 CD BAND TUNER OFF TAPE 1 1 b a 6,2 2 HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME + E-26 RECORDING To exchange a CD for another CD while recording 2 1 Press the stop button of the CD during recording. * The tape stops after about 2 seconds and enters recording standby mode. 2 3 Replace the CD. 4 Press the play button of the CD. * Recording begins after about 2 seconds. 1 4 Choose the selection to be recorded next by using the or button. Note The CD Synchronised Recording System will function even when the CD player is set to the program play or random play mode. In this case, when more than 2 seconds elapse between tracks, the tape will stop automatically and resume recording when the beginning of the next track is found. 3 3 When recording is continuously made on both sides of the tape 1 2 3 4 Even if the recording for side A is finished halfway through a track, side B will automatically start recording from the beginning of that track. (Auto restart function) So recording for side B will be made without cutting the beginning of a track. 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 4 1 REPEAT CD BAND TUNER OFF TAPE b a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME + E-27 RECORDING 1 7 To edit tracks dividing them to side A and side B automatically (Auto editing function) 8 To use tapes effectively, tracks on a CD are automatically rearranged between side A and side B to best utilize the length of the tape. When the desired tracks are selected in program selection, the tracks stored in memory are automatically divided between side A and side B. 6 4 3 5 1 2 Select the CD position and load the CD to be recorded. 3 When recording with the Dolby NR system, set the DOLBY NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the “Dolby B and C Type Noise Reduction” on page 24. 4 5 Set the REVERSE MODE switch to 6 Press the C46, C60 or C90 according as the length of the tape to be used. 2 Load a tape into the tape “b” cassette compartment. * Rewind the tape onto the left-side reel. . Press the REC button. * The indicator beside the REC button lights up and the play indicators flash. When using tapes other than C46, C60 or C90 Press the or button to adjust the time (minute by minute). • Adjustable range is from C10 to C99. 1 2 3 4 6 7 8 9 0 PROG CLEAR CALL TIME +10 REPEAT 5 5 CD BAND It is also possible to use the track number input buttons on the remote control to set the tape length. • For a tape length of C30, press the “+10”, “+10”, “+10” and “0”. (Press each button within 3 seconds after the previous one has been pressed.) TUNER b 7 Press the EDIT button. * Tracks on the CD are automatically divided between side A and side B. * The number of tracks, total time and track numbers to be recorded on side A and side B are displayed for approximately 4 seconds. (When there are tracks which can not be recorded, the “TIME OVER” indicator will light up.) 8 Press the play button of the CD. * CD playback and recording start approximately 9 seconds after the tape starts (after the part of the tape on which recording can not be performed is wound). 1 8 a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT OFF - TAPE VOLUME + To cancel auto editing function Before recording, press the stop button of the CD. To stop recording Press the stop button of the tape. (At this time, CD playback automatically stops.) E-28 RECORDING To confirm tracks to be recorded and tracks which can not be recorded 1 2 3 4 5 6 7 8 9 0 PROG CLEAR CALL TIME +10 REPEAT Before recording, press the TIME button. The following information will appear on the display by turns whenever the TIME button is pressed. TIME → Tracks to be recorded on side A ↓ CD BAND Tracks to be recorded on side B ↓ TUNER b Tracks which can not be recorded on side A and side B (When all tracks can be recorded, “00 0:00” is displayed) a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT OFF - ↓ TAPE VOLUME + Tracks which can be recorded on side A and side B Note Once CD playback starts, the display does not change. Dubbing 2 • 1 • 3 During dubbing, adjusting the VOLUME, BALANCE, TREBLE and BASS controls and selecting any sound processor program have no effect on the recorded sound. Try to use the same tape formula and length for the recording tape as for the master tape. 1 2 Select the TAPE position. 3 Set the REVERSE MODE switch to to record on only one side, or to for continuous recording on both sides. 4 Press the DUBBING button. * Press “NORMAL” to dub at normal speed, and “HIGH” to dub at about twice the normal speed. * Dubbing will begin from side A. Load a prerecorded tape into the tape “a” cassette compartment. Insert a blank tape into the tape “b” cassette compartment. To stop dubbing 4 Press the stop button for tape “a” or “b”. * Tape “a” and tape “b” will stop at the same time. Note Only tapes originally encoded with Dolby B or C NR will be dubbed onto tapes with Dolby B or C NR encoding. The DOLBY NR switch will have no effect on the recording of tape “b” during dubbing. However, the playback tonal quality of tape “a” will change according to the DOLBY NR switch position. E-29 RECORDING Recording from the built-in tuner 2 4 3 1 5 1 2 3 4 6 7 8 9 0 PROG CLEAR CALL TIME +10 REPEAT 5,1 1 6 1 Tune to the desired station. (Refer to the “TUNER OPERATION” on page 19.) 2 3 Load a tape into the tape “b” cassette compartment. 4 Set the REVERSE MODE switch to to record on only one side, or to for continuous recording on both sides. 5 Press the REC button. * The indicator beside the REC button lights up and the play indicators flash. 6 Press the play button to record side A, or the play button to record side B. * For continuous recording of both sides, begin on side A. Recording stops automatically at the end of side B. 5 CD BAND TUNER OFF TAPE When recording with the Dolby NR system, set the DOLBY NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the “Dolby B and C Type Noise Reduction” on page 24. To stop recording temporarily 6,2 2 1 2 b Press the PAUSE button. To resume recording, press the play button whose indicator is flashing. a HALL JAZZ CLUB ROCK CNCT POWER AUX DAT - VOLUME To stop recording Press the stop + button. Erasing recorded tapes E-30 1 Load the tape to be erased into the tape “b” cassette compartment. 2 3 Select the AUX position with the INPUT selector. 4 Press the REC button, then press the play button to erase side A of tape, or the play button to erase side B. Set the REVERSE MODE switch to side and to to erase both sides. to erase only one HOW TO USE THE BUILT-IN TIMER 6 5 Before setting the timer clock, make sure that the current time is correct. 4 Timer operation To listen to the tuner 1 2 Select the TUNER position. 3 4 Press the DISPLAY button. 5 Release the TIME ADJUST button. * When the start time of the timer is set by mistake, press the CLEAR button and repeat step 4. 6 Press the TIMER button. * “TIMER” appears on the display. This sets the timer to the stand-by condition. * The tuner turns on automatically at the desired time. 3 1 CLEAR 2 1 Tune to the desired station. (Refer to the “TUNER OPERATION” on page 19.) While the “TIMER” indicator is flashing, and while pressing the TIME ADJUST button, press the HOUR and MINUTE buttons to set the desired time. To play a compact disc 1 2 3 2 Select the CD position. Load the disc. Perform steps 3 – 6 of the “To listen to the tuner” section. * CD playback starts automatically at the desired time. To playback a cassette tape 1 3 E-31 1 2 Select the TAPE position. 3 4 Set the TIMER switch to the PLAY position. Load a recorded cassette tape into the tape “a” or tape “b” cassette compartment. * If tapes are loaded in both the compartments, tape “b” will be played back by the timer play. Perform steps 3 – 6 of the “To listen to the tuner” section. * Tape playback starts automatically at the desired time. (Playback of the side which corresponds to the play button which illuminated just before the timer setting was completed will commence.) HOW TO USE THE BUILT-IN TIMER To record tuner programs POWER DISPLAY 1 Load a blank cassette tape into the tape “b” cassette compartment. 2 3 Set the TIMER switch to the REC position. Perform steps 1 – 5 of the “To listen to the tuner” section on the previous page. * Recording starts automatically at the desired time. Notes The power will be automatically turned off 2 hours after the timer starts. To set the desired volume level for listening to a source with the timer, use the VOLUME control before setting the timer. • Except when you perform recording with the timer, be sure to set the TIMER switch to the PLAY position. • • To confirm the timer time setting Press the DISPLAY button. To cancel the timer operation VOLUME 2 Press the POWER switch. * The “TIMER” indicator will go out. * Unless the AC supply lead is unplugged or there is a power failure, the time set on the timer will be retained until it is reset. 1 E-32 HOW TO USE THE BUILT-IN TIMER Sleep timer operation SLEEP This unit can be turned off automatically. Play the desired sound source. Press the SLEEP button repeatedly until the desired sleep time appears in the display. The display will change as described below. (Time is displayed by the minute.) 30 ↑ 45 Current Time ↑ ↑ 60 ↑ ↑ 1 2 15 * The original display mode will resume about 5 seconds after the selection is made. * If the current time is selected, the power is turned off after 2 seconds. 3 The unit will turn off automatically after the preset sleep time. To confirm the sleep time setting Press the SLEEP button once. The remaining time of the preset sleep time appears in the display. To change the sleep time ↑ 15 ↑ Current time 30 ↑ ↑ Remaining time of the preset sleep time 60 ↑ While the “SLEEP” indicator is on, press the SLEEP button repeatedly until the desired time to replace appears. The display will change as described below. 45 ↑ POWER * If the current time is selected, the power is turned off after 2 seconds. To stop the sleep timer operation Press the POWER switch. (The “SLEEP” indicator will go out.) Using the timer and the sleep timer at the same time 1 2 Prepare timer playback. (See page 31.) Press the SLEEP button and set the sleep time. * When the sleep timer operation finishes, the timer will function to turn the source on at the preset time. Notes * The source set in the sleep timer operation will be turned on at the time set in the timer playback operation. * Do not set the timer time so that the timer will start during sleep timer operation. (Since sleep timer operation has priority, the timer will not operate.) E-33 USING EXTERNAL UNITS Auxiliary (AUX) 1 Connect the output lead of a video cassette player, video disc player, etc. to the AUX inputs of this unit. (red → right channel, white → left channel) 2 3 4 Select the AUX position with the INPUT selector. Operate the unit connected to the AUX inputs. Start recording with this unit, if so desired. (See page 30.) Auxiliary (DAT) (U.S.A., Canada and General models) 1 Connect the output lead of a DAT or another input source. (red → right channel, white → left channel) 2 3 4 Select the DAT position with the INPUT selector. Operate the unit connected to the DAT inputs. Start recording with this unit, if so desired. (See page 30.) Turntable (PHONO) (U.K., Australia and Europe models) E-34 1 Connect the output lead of a turntable. (red → right channel, white → left channel) 2 3 4 5 Connect the GND lead of a turntable. Select the PHONO position with the INPUT selector. Operate the turntable. Start recording with this unit, if so desired. (See page 30.) USING EXTERNAL UNITS Headphones • • Be sure that your headphones have a 3.5 mm (1/8”) diameter plug and are between 16 ohms and 50 ohms impedance. Recommended impedance is 32 ohms. When headphones are connected, the speakers are defeated automatically. Adjust the VOLUME control for desired volume. MAINTENANCE Internal care Tape “a” • • Tape “b” Dirty heads, capstans and pinch rollers can cause poor sound and tape jams. Clean these parts with a cotton swab moistened with commercial head/pinch roller cleaner or isopropyl alcohol. After long use, the deck’s heads and capstans may become magnetised, causing poor sound. Demagnetise these parts once every 30 hours of playing/recording time by using a commercial tape head demagnetiser. Read the demagnetiser’s instructions carefully before use. External care • • E-35 Periodically wipe the cabinet with a soft cloth and dilute soap solution, then wipe with a dry cloth. Do not use chemically treated cleaning cloths or other chemicals. (See “Precautions”.) SPECIFICATIONS As a part of policy of continuous improvement, YAMAHA reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. ■ Tuner/CD player section ■ Amplifier section Power source .................................. AC supplies from amplifier unit Input sensitivity and input impedance ..... AUX; 200 mV/47 kohms Load impedance .................................. Headphones; 16 – 50 ohms (recommended; 32 ohms) Dimensions ............................................... Width; 277 mm (10-7/8”) Height; 114.5 mm (4-1/2”) Depth; 258.5 mm (10-3/16”) Weight ................................................................ 2.3 kg (5 lbs. 1 oz.) Power Supply [U.S.A. and Canada models] ............................ AC 120V, 60 Hz [Australia and U.K. models] ............................. AC 240V, 50 Hz [Europe model] ................................................. AC 230V, 50 Hz [General model] ...................... AC 110/120/220/240V, 60/50 Hz Power consumption [U.S.A. model only] .......................................................... 120 W [Canada model only] ........................................................ 165 W [Australia, Europe, U.K. and General models] .............. 125 W Continuous power output [U.S.A. and Canada models] ........................... 2 x 35W, 40 Hz – 20 kHz, 6 ohms, 0.9% T.H.D. [Australia and General models] ............................................ 2 x 50W, 1 kHz, 6 ohms, 10% T.H.D. [U.K. and Europe models] ........................................... 2 x 42W, 1 kHz, 6 ohms, 0.9% T.H.D. 2 x 40W, 1 kHz, 6 ohms, 0.7% T.H.D. (DIN) Load impedance ................................................. Speakers; 6 ohms Dimensions ............................................... Width; 277 mm (10-7/8”) Height; 114.5 mm (4-1/2”) Depth; 304 mm (11-15/16”) Weight ....................................................................... 5.0 kg (11 lbs.) (Tuner) Frequency range FM .................................................................... 87.5 – 108.0 MHz AM (MW/LW) [U.S.A. and Canada models] ............... AM; 530 – 1,720 kHz [Australia and General models] .......... AM; 530 – 1,620 kHz [U.K. and Europe models] .................. MW; 522 – 1,620 kHz LW; 153 – 281 kHz Sensitivity FM ...................................................................................... 1.0 µV AM (MW/LW) [U.S.A., Canada, Australia and General models] .......................................................................... AM; 500 µV/m [U.K. and Europe models] ............................. MW; 500 µV/m LW; 560 µV/m ■ Tape Deck Section Power source .................................. AC supplies from amplifier unit Tape .............................................................. Compact cassette tape Frequency response (Playback) ..... 30 – 13,000 Hz (Normal tape) 30 – 14,000 Hz (CrO2 tape) Signal/noise ratio ....................................... 64 dB (Dolby B NR ON) 72 dB (Dolby C NR ON) Dimensions ............................................... Width; 277 mm (10-7/8”) Height; 114.5 mm (4-1/2”) Depth; 251.5 mm (9-7/8”) Weight .............................................................. 2.7 kg (5 lbs. 15 oz.) (Compact disc player) Type .................................................................. Compact disc player Signal readout ....................... Non-contact, 3-beam semi-conductor laser pick-up Rotation speed ................................... 200 – 500 rpm CLV, Approx. Error correction .......CIRC (Cross Interleave Reed-Solomon Code) D/A converter .......................................................................... 16-bit Filter ..............................4-time oversampling digital filter active filter Frequency response ............................................... 20 – 20,000 Hz Wow and flutter ............Unmeasurable (less than 0.001% W. peak) ■ Speaker section Type .................................................... Active Servo Processing type Speakers ........................................................ 12 cm (4-3/4”) woofer 5 cm (2”) tweeter Frequency range ..................................................... 40 – 20,000 Hz Maximum power handling capacity......................................... 50W Impedance ............................................................................ 6 ohms Dimensions ............................................... Width; 180 mm (7-1/16”) Height; 342.5 mm (13-1/2”) Depth; 219.5 mm (8-5/8”) Weight ..................................................... 3.5 kg (7 lbs. 11 oz.)/each E-36 TROUBLESHOOTING If your unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. AMPLIFIER AC supply lead is not plugged in. Plug in AC supply lead. No sound from one speaker Loose speaker connections. Connect properly. No sound from speakers. Internal protection circuit is functioning. Unplug AC supply lead from the wall AC outlet, and then plug in again. Excessive static in FM broadcasts. Interference from starting motor of nearby car. Position the FM antenna as high and as far away from nearby roads as possible. Connect using a coaxial cable. Interference from thermostat of nearby electrical appliance. TUNER REMEDY CAUSE SYMPTOM No power even if the POWER switch is pressed. Noise increases during stereo broadcasts. Antenna input is too weak due to obstructions or excessive distance from broadcasting station. Stereo broadcasts are noisy and STEREO indicator blinks on and off. Insufficient antenna input. Install a multi-element type FM antenna if possible. Install an antenna appropriate for the electric field strength of your area. Cannot select preset stations. Preset memory has been erased. Reprogram memory presets. Buzzing or static during AM (LW or MW) broadcasts. Interference from source such as lightning, flourescent lights, electric motors or thermostat of nearby electrical appliance. Problem is difficult to eliminate but can be lessened by grounding MW/LW (AM) loop antenna. Check antenna connections. TV or microprocessor is being used nearby. Move away from TV or microprocessor. AM (LW or MW) broadcast sensitivity is poor. Can’t set timer. Radio signal is weak or antenna is not properly connected. Properly connect MW/LW (AM) loop antenna. Can’t set timer. Current time is not set. Set current time. Timer doesn’t function as expected. Power is turned off using the POWER switch. After setting timer, turn power off using the TIMER button. Play does not begin even if disc is loaded. Disc is upside down. Load disc label side up. No sound. Disc is dirty. Input selector setting is incorrect. Clean disc. Select the CD position of the input selector. Sound stops suddenly (always at same spot). Disc is dirty. Clean disc. Volume set too high. Lower volume. Tape won’t move during playback or recording. Slack tape wrapped around pinch roller. Take up slack with a pencil before using. Can’t record. Erasure prevention tab is broken off. Head is dirty. Replace tape or cover erasure prevention hole with cellophane tape. Clean heads. Head is dirty. Clean heads. Head has become magnetized. Tape is worn. Demagnetize heads with head eraser. Replace tape. Poor sound quality. DOLBY NR switch is set to wrong position. Stereo balance is poor. Head is dirty. Set to positions matching those used when tape was recorded. Clean heads. Excessive noise. Head is dirty. Change orientation of MW/LW (AM) loop antenna. CD PLAYER Install an external MW/LW (AM) antenna. REMOTE CONTROL TAPE DECK Sound is distorted or fades out. Tape travel stops in middle of playback or recording. Slack tape coming out of cassette shell. Clean heads. Demagnetize heads with head eraser. Replace tape. Take up slack by turning reels with a pencil. Tape is creased or torn. Endless tape is being used. Replace with new tape. Don’t use endless tapes. Can’t find specific selections on tape. Silent gaps between selections are too short. Excessively soft passages in middle of selections. Conversation etc. is recorded. Batteries are dead. The music search function won’t operate unless the silent gaps between selections are at least four seconds long. Remote control is too far away or is being used at incorrect angle. Use within 6 m and 30° radius. Direct sunlight or lighting (of an inverter type of flourescent lamp etc.) is striking the remote control sensor of the main unit. Remote control is being used near TV set with infrared photo sensor. Change position of the main unit. Head has become magnetized. Tape is worn. Remote control doesn’t work. TV functions strangely when the remote control is used. E-37 Replace batteries. Move TV farther away or cover its infrared photo sensor. YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, D-25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA