Whirlpool AKR 928 IX Program Chart

Marca: Whirlpool

Modelo: AKR 928 IX

Categoría: Campanas de cocina

Tipo: Program Chart

El Whirlpool AKR 928 IX es una campana extractora que cuenta con cuatro velocidades de extracción, luz halógena y filtro de grasa. Gracias a su filtro de carbón, puede funcionar en modo filtrante o modo extracción. El filtro de grasa debe lavarse una vez al mes y puede lavarse en el lavavajillas a alta temperatura. El filtro de carbón puede lavarse y reactivarse en el horno a 100 °C durante 10 minutos.



5019 318 33002

AKR 928

INSTALLATIONSANGABEN

Mindestabstand zur Kochfläche: 65 cm (Elektroplatten), 75 cm (Gas-, Öl- oder

Kohlekochplatten). Folgen Sie bei der Installation der Nummerierung

.....). Das Abzugsrohr und die Befestigungsschellen (15) werden nicht

mitgeliefert. Sie müssen sie gesondert kaufen. Prüfen Sie den Stromanschluss

der Beleuchtung und des Motors (17). Versperren Sie die abnehmbare

Verkleidung mit den Schrauben fest an der Dunstabzugshaube (18). Die

Verkleidung kann verschiedene Formen haben, trotzdem bleiben Montage- und

Befestigungsverfahren gleich.

INSTALLATION SHEET

Minimum height above cooker: 65 cm (electric cookers), 75 cm (gas, gas oil or

coal cookers). To install, follow points (1

.....). The exhaust pipe and

fixing clamps (15) are not provided and should be bought separately. Check for

correct electrical connections of lights and motor (17). Tighten the screws fixing

the removable casing to the hood (18). The casing can be in various shapes, but

the procedure for fitting and fixing to the hood is the same.

FICHE D'INSTALLATION

Distance minimale par rapport à la cuisinière : 65 cm (cuisinière électrique),

75 cm (cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la

numérotation (1

.....). Le tuyau d'évacuation et les colliers de fixation

(15) ne sont pas fournis avec l'appareil et doivent être acheté auprès du Service

après-vente. Contrôlez que le branchement électrique de l'éclairage et du moteur

ont été effectués correctement (17). Serrez à fond les vis fixant le capot

amovible à la hotte (18). Le modèle du capot peut être différent mais la

procédure d'insertion et de fixation à la hotte reste identique.

INSTALLATIEKAART

Minimumafstand tot het kooktoestel: 65 cm (elektrische kooktoestellen), 75 cm

(kooktoestellen op gas, olie of kolen). Volg voor de montage de nummering

.....). De afvoerleiding en de bevestigingsklemmen (15) worden niet

bijgeleverd en dienen aangeschaft te worden. Verzeker u ervan dat de verlichting

en de motor correct aangesloten zijn (17). Draai de twee schroeven, waarmee de

losse mantel aan de kap (18) is bevestigd, heel goed aan. De procedure voor

plaatsing en bevestiging van de kap in de mantel is identiek voor alle type

mantels.

31833002.fm5 Page 1 Thursday, April 12, 2001 3:18 PM



5019 318 33002

AKR 928

FICHA DE INSTALACIÓN

Distancia mínima desde los quemadores: 65 cm (quemadores eléctricos), 75 cm

(quemadores de gas, gasóleo o carbón). Para el montaje, siga la

numeración(1

.....). El tubo de descarga y las abrazaderas de fijación

(15) no se suministran de fábrica sino que se deben comprar. Compruebe que la

conexión eléctrica de las luces y del motor es correcta (17). Atornille bien los

tornillos que fijan la capa desmontable a la campana (18). La capa puede ser de

distintas formas, pero el procedimiento para introducirla y fijarla a la campana

no varía.

FICHA DE INSTALAÇÃO

Distância mínima dos fogões: 65 cm. (fogões eléctricos), 75 cm. (fogões a gás,

óleo ou carbono). Para a montagem siga a numeração (1

.....). O tubo de

descarga e tiras de fixação (15) não são fornecidos com o aparelho pelo que

devem ser adquiridos. Controle se a ligação eléctrica das luzes e do motor está

feita correctamente (17). Aperte muito bem os parafusos que prendem a

cobertura amovível do exaustor (18). A cobertura pode ser de diferentes formas,

mas o procedimento e a fixação ao exaustor permanece idêntica.

SCHEDA INSTALLAZIONE

Distanza minima dai fuochi: 65 cm (fuochi elettrici), 75 cm (fuochi a gas,

gasolio o carbone). Per il montaggio seguire la numerazione (1

.....).

Tubo di scarico e fascette di fissaggio (15) non sono fornite e vanno acquistate.

Controllare il corretto collegamento elettrico di luci e motore (17). Serrare con

decisione le viti che fissano il mantello rimovibile alla cappa (18). Il mantello

può essere di forme diverse, ma la procedura di inserimento e fissaggio alla

cappa rimane identica.

ùüùü+ùùùþ

ü$12.)12.1. )2"0120" FP02!"0120" FP

0120".0! #02!0. #0! # +.22  21

.  #1202.!1





1&."..&".2.

 !.120!&1"/0/.202.02 . !! 32!..!0

.. 2 *$&!12ü2021&1202!1*/01

3&212+. 2!320.2"/0" #1#!.2 *2 

.3.! *0 #.12 . !! 32!. #. !0.

$0/.3 !02)1$.././.1.2  21".120!&1"

12 . !! 32!..!.0/.

31833002.fm5 Page 2 Thursday, April 12, 2001 3:18 PM



5019 318 33002

AKR 928

Nur in der Umluftversion

mit Fettfilter

For Filter Version only

Uniquement pour la

Version filtrante

Uitsluitend voor de

filterversie

Sólo para el modelo

filtrador

Apenas para Versão

filtrante

Solo per Versione filtrante

) . 2 

..!!)31"

31833002.fm5 Page 3 Thursday, April 12, 2001 3:18 PM



5019 318 33002

AKR 928

1. Control panel

a. Light ON/OFF switch.

b. Extraction and minimum extraction speed

ON/OFF switch.

c. Medium extraction speed switch.

d. Maximum extraction speed switch.

2. Grease filter

3. Halogen bulbs

4. Steam deflector

5. Telescopic flue

To clean the grease filter

Wash the grease filter at least once a month.

1. Disconnect the electrical power supply.

2. Remove the grease filters -Fig. 1: pull the spring

release handle (f) downwards, then remove the

filter.

3. After cleaning the grease filter refit in reverse

order, making sure the entire extraction surface

is covered.

Replacing bulbs

1. Disconnect the electrical power supply.

2. Use a small screwdriver or any other suitable tool

to prise off (m-Fig. 2) the lamp cover (p-Fig. 2).

3. Replace the burnt-out bulb.

Use 20 W max halogen bulbs only, taking care not

to touch them with hands.

4. Close the lighting unit (snap-close).

Carbon filter Fitting and Maintenance

Fitting the carbon filter:

1. Disconnect the electrical power supply.

2. Remove the grease filter (f-Fig. 1).

3. Remove the screw and then the filter holder

(g-Fig. 3).

4. Fit the carbon filter (h-Fig. 3) in the filter holder

(i-Fig. 3).

5. Refit the filter holder and secure it to the hood

with the screw (g-Fig. 3).

6. Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can

be washed and reactivated.

With normal hood use, the filter should be cleaned

once a month. The best way to clean the filter is in a

dishwasher at the highest temperature possible,

using a normal dishwasher detergent. To avoid

particles of food or dirt settling on the filter during

washing and giving rise to unpleasant smells, it is

advisable to wash the filter on its own. After

washing, dry the filter in the oven at 100° C for

10 minutes to reactivate it.

The filter will retain its odour-absorbing capacity for

three years, after which it must be replaced.

Fig. 1 Fig. 2

Fig. 3

PRODUCT SHEET

F NL E PD GRI

31833002.fm5 Page 6 Thursday, April 12, 2001 3:18 PM

Transcripción de documentos

31833002.fm5 Page 1 Thursday, April 12, 2001 3:18 PM AKR 928 D INSTALLATIONSANGABEN Mindestabstand zur Kochfläche: 65 cm (Elektroplatten), 75 cm (Gas-, Öl- oder Kohlekochplatten). Folgen Sie bei der Installation der Nummerierung (1Ö2Ö3Ö.....). Das Abzugsrohr und die Befestigungsschellen (15) werden nicht mitgeliefert. Sie müssen sie gesondert kaufen. Prüfen Sie den Stromanschluss der Beleuchtung und des Motors (17). Versperren Sie die abnehmbare Verkleidung mit den Schrauben fest an der Dunstabzugshaube (18). Die Verkleidung kann verschiedene Formen haben, trotzdem bleiben Montage- und Befestigungsverfahren gleich. GB INSTALLATION SHEET Minimum height above cooker: 65 cm (electric cookers), 75 cm (gas, gas oil or coal cookers). To install, follow points (1Ö2Ö3Ö.....). The exhaust pipe and fixing clamps (15) are not provided and should be bought separately. Check for correct electrical connections of lights and motor (17). Tighten the screws fixing the removable casing to the hood (18). The casing can be in various shapes, but the procedure for fitting and fixing to the hood is the same. F FICHE D'INSTALLATION Distance minimale par rapport à la cuisinière : 65 cm (cuisinière électrique), 75 cm (cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la numérotation (1Ö2Ö3Ö.....). Le tuyau d'évacuation et les colliers de fixation (15) ne sont pas fournis avec l'appareil et doivent être acheté auprès du Service après-vente. Contrôlez que le branchement électrique de l'éclairage et du moteur ont été effectués correctement (17). Serrez à fond les vis fixant le capot amovible à la hotte (18). Le modèle du capot peut être différent mais la procédure d'insertion et de fixation à la hotte reste identique. NL INSTALLATIEKAART Minimumafstand tot het kooktoestel: 65 cm (elektrische kooktoestellen), 75 cm (kooktoestellen op gas, olie of kolen). Volg voor de montage de nummering (1Ö2Ö3Ö.....). De afvoerleiding en de bevestigingsklemmen (15) worden niet bijgeleverd en dienen aangeschaft te worden. Verzeker u ervan dat de verlichting en de motor correct aangesloten zijn (17). Draai de twee schroeven, waarmee de losse mantel aan de kap (18) is bevestigd, heel goed aan. De procedure voor plaatsing en bevestiging van de kap in de mantel is identiek voor alle type mantels. 5019 318 33002 31833002.fm5 Page 2 Thursday, April 12, 2001 3:18 PM AKR 928 E FICHA DE INSTALACIÓN Distancia mínima desde los quemadores: 65 cm (quemadores eléctricos), 75 cm (quemadores de gas, gasóleo o carbón). Para el montaje, siga la numeración(1Ö2Ö3Ö.....). El tubo de descarga y las abrazaderas de fijación (15) no se suministran de fábrica sino que se deben comprar. Compruebe que la conexión eléctrica de las luces y del motor es correcta (17). Atornille bien los tornillos que fijan la capa desmontable a la campana (18). La capa puede ser de distintas formas, pero el procedimiento para introducirla y fijarla a la campana no varía. P FICHA DE INSTALAÇÃO Distância mínima dos fogões: 65 cm. (fogões eléctricos), 75 cm. (fogões a gás, óleo ou carbono). Para a montagem siga a numeração (1Ö2Ö3Ö.....). O tubo de descarga e tiras de fixação (15) não são fornecidos com o aparelho pelo que devem ser adquiridos. Controle se a ligação eléctrica das luzes e do motor está feita correctamente (17). Aperte muito bem os parafusos que prendem a cobertura amovível do exaustor (18). A cobertura pode ser de diferentes formas, mas o procedimento e a fixação ao exaustor permanece idêntica. I SCHEDA INSTALLAZIONE Distanza minima dai fuochi: 65 cm (fuochi elettrici), 75 cm (fuochi a gas, gasolio o carbone). Per il montaggio seguire la numerazione (1 Ö2Ö3Ö.....). Tubo di scarico e fascette di fissaggio (15) non sono fornite e vanno acquistate. Controllare il corretto collegamento elettrico di luci e motore (17). Serrare con decisione le viti che fissano il mantello rimovibile alla cappa (18). Il mantello può essere di forme diverse, ma la procedura di inserimento e fissaggio alla cappa rimane identica. *5 ù üùü+ ù ù ùþ 5019 318 33002 ü$12.)12.1.)2"0120" FP 02!"0120" FP 0120".0! #02!0. #0! # +.22 21 . #1202.!1 ÖÖÖ 1&."..&".2. !.120!&1" /0/.202.02 . !! 32!..!0 .. 2 *$&!12ü2021&1202!1*/01 3&212+. 2! 320.2"/0" #1#!.2 *2 .3.! *0 #.12 . !! 32!. #. !0. $0/.3 !02)1$.././.1.2 21".120!&1" 12 . !! 32!..!.0/. 31833002.fm5 Page 3 Thursday, April 12, 2001 3:18 PM AKR 928 Nur in der Umluftversion mit Fettfilter For Filter Version only Uniquement pour la Version filtrante Uitsluitend voor de filterversie 5019 318 33002 Sólo para el modelo filtrador Apenas para Versão filtrante Solo per Versione filtrante ) . 2 ..!!)31" 31833002.fm5 Page 6 Thursday, April 12, 2001 3:18 PM AKR 928 PRODUCT SHEET 1. Control panel a. Light ON/OFF switch. b. Extraction and minimum extraction speed ON/OFF switch. c. Medium extraction speed switch. d. Maximum extraction speed switch. 2. Grease filter 3. Halogen bulbs 4. Steam deflector 5. Telescopic flue To clean the grease filter Wash the grease filter at least once a month. 1. Disconnect the electrical power supply. 2. Remove the grease filters -Fig. 1: pull the spring release handle (f) downwards, then remove the filter. 3. After cleaning the grease filter refit in reverse order, making sure the entire extraction surface is covered. Replacing bulbs 1. Disconnect the electrical power supply. 2. Use a small screwdriver or any other suitable tool to prise off (m-Fig. 2) the lamp cover (p-Fig. 2). 3. Replace the burnt-out bulb. Use 20 W max halogen bulbs only, taking care not to touch them with hands. 4. Close the lighting unit (snap-close). Carbon filter Fitting and Maintenance Fitting the carbon filter: 1. Disconnect the electrical power supply. 2. Remove the grease filter (f-Fig. 1). 3. Remove the screw and then the filter holder (g-Fig. 3). 4. Fit the carbon filter (h-Fig. 3) in the filter holder (i-Fig. 3). 5. Refit the filter holder and secure it to the hood with the screw (g-Fig. 3). 6. Refit the grease filter. Fig. 1 Fig. 2 Carbon filter maintenance: Unlike traditional carbon filters, this carbon filter can be washed and reactivated. With normal hood use, the filter should be cleaned once a month. The best way to clean the filter is in a dishwasher at the highest temperature possible, using a normal dishwasher detergent. To avoid particles of food or dirt settling on the filter during washing and giving rise to unpleasant smells, it is advisable to wash the filter on its own. After washing, dry the filter in the oven at 100° C for 10 minutes to reactivate it. The filter will retain its odour-absorbing capacity for three years, after which it must be replaced. 5019 318 33002 D GB F NL E P I GR Fig. 3