Kichler Lighting 15401AZT Manual de usuario

Tipo
Manual de usuario
INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause “sunburn”.)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Use only with wattage and lamp marked on fixture.
8) Do not touch the inner glass envelope of the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
9) Do not operate the fixture with a damaged or missing lens.
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
This fixture is intended for installation in accordance with the National Electric
Code (NEC) and Local code specifications. Failure to adhere to these codes and
instructions may result in serious injury and/or property damage and will void the
warranty.
1) WARNING: This fixture is not to be installed within 10 feet (3M) of a pool, spa
or fountain.
2) This fixture is to be used only with a power unit (transformer) rated a maximum
of 300 W (25 AMPS) 15 volts.
3) The #18 ga. fixture wire is not intended for direct burial.
4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath the
surface of the ground.
NOTE: If additional Direct Burial wire is needed, contact your local Kichler
®
landscape distributor.
8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.
10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.
12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK; 250’ (76 M),
15502-BK; 500’ (152M), 15505-BK; and 1000’ (304 M), 15506-BK.
5) Fixture shall not use a tungsten halogen lamp unless the fixture is marked for
use with such lamps.
6) Wiring connections must be made with approved/listed wire connection
device(s) suitable for the application. Do not exceed manufacturers’ wiring
combination specifications for size and quantity of conductors.
CAUTION
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE), CARE
SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES, GRASS
CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT BULB, LENS, OR
BODY OF THE FIXTURE.
ASSEMBLY AND INSTALLATION
1) Determine desired location for mounting fixture.
2) At desired location, hammer stake (A) into ground. To avoid damage to stake,
place a board on top of stake while hammering. If ground is hard and stake is
difficult to install, make a crosscut in ground using a flat shovel.
3) Clear away area in ground at wireway slot (B) in top of stake (A).
4) Lay 12V cable into wireway slot (B) and screw stem (D) into stake (A). If
assembly does not look straight, adjust by pushing or pulling on stake only.
5) Install provided lamp (E) into socket inside fixture.
6) Pass fixture hood (G) over bulb and set on top of stem (D).
7) Screw fixture hood (G) onto stem (D). (DO NOT over tighten.)
8) TURN OFF POWER.
9) Make wire connections using supplied wire nuts following instructions on bag.
INSTRUCCIONES PERTINENTES A UN RIESGO DE ICENDIO O LESION A LAS PERSONAS
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
¡La lámpara encendida es CALIENTE!
ADVERTENCIA — Para disminuir el riesgo de INCENDIO O LESION A LAS PERSONAS.
1) Apague / desenchufe y deje que se enfríe antes de cambiar la lámpara.
2) ¡La lámpara se CALIENTA rápidamente! Haga contacto del conmutador/
enchufe sólo cuando encienda.
3) No toque la lente o la capucha caliente.
4) No permanezca en la luz si siente tibia la piel. (La luz es intensa, puede causar
“quemaduras de sol”).
5) No mire directamente a la lámpara encendida.
6) Mantenga la lámpara alejada de los materiales que puedan encenderse.
7) Use solamente con el vatiaje y la lámpara marcados en el artefacto.
8) No toque el vidrio del interior de la lámpara en ningún momento. Use un paño
suave. El aceite del cuerpo puede dañar la lámpara.
9) No haga funcionar el artefacto con una lente dañada o faltante.
INSTRUCCIONES DE SEGURIDAD
PRIMERO LEA ESTO
GUARDE ESTAS INSTRUCCIONES
Este artefacto se debe instalar de acuerdo con el Código Eléctrico Nacional
(NEC, por sus siglas en inglés) y con las especificaciones del código local. No
cumplir con estos códigos e instrucciones puede resultar en lesiones graves y/
o en daños a la propiedad y anulará la garantía.
1) ADVERTENCIAERTENCIA: Este artefacto no debe instalarse a menos de 10 pies
(3 m) de una piscina (alberca), spa o fuente.
2) Este artefacto debe utilizarse solamente con una unidad de potencia (tranformador)
con capacidad nominal máxima de 300 vatios (25 amp.) 15 voltios.
Date Issued: 9/25/15 IS-15430-US
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page
3) De acuerdo con los requisitos del Código Eléctrico Nacional (NEC por sus
siglas en inglés), el alambre clasificado para soterrado directo se debe enterrar un
mínimo de 6 pulgadas [152 mm.] debajo de la superficie del terreno.
El alambre calibre 8 puede comprarse en longitud de 250’ (76 m.), 15503-BK
El alambre calibre 10 puede comprarse en longitud de 250’ (76 m.), 15504-BK
El alambre calibre 12 puede comprarse en longitudes de 75’ (22 m.), 15550-BK;
100’ (30 m.), 15501-BK; 250’ (76 m.), 15502-BK; 500’ (152 m.), 15505-BK; y
1000’ (304 m.), 15506-BK.
4) El artefacto no debe utilizarse con lámparas de halógeno, a menoss que el
artefacto esté marcado para usar con tales lámparas.
5) Las conexiones de cableado se deben hacer con las conexiones del(los)
dispositivos) de conexión de cableado aprobados/ de la lista, adecuados
para la aplicación. No exceda las especificaciones de combinación de
cableado del fabricante para el tamaño y cantidad de conductores.
PRECAUCION
CUANDO SE INSTALE SISTEMAS DE ALUMBRADO KICHLER PARA JARDINES (YA SEA DE VOLTAJE
DE LINEA O CON VOLTAJE BAJO) SE DEBE TENER CUIDADO DE MAINTNERLOS ALEJADOS DE
MATERIALES QUE PUEDAN SER COMBUSTIBLES EN POTENCIA.
AL DAR SERVICIO DE MANTENIMIENTO A ESTOS SISTEMAS, ASEGURESE DE DESPEJAR LAS
HOJAS, CONOS DE PINO, RECORTES DEL PASTO, CUBIERTA DE PAJA O CUALQUIER BASURA QUE
SE HAYA ACUMULADO EN LA BOMBILLA DE LUZ, EL LENTE O EL SOPORTE DE LA BOMBILLA.
MONTAJE E INSTALACIÓN
1) Determine el lugar deseado para montar el artefacto.
2) En el lugar deseado, martille la estaca (A) en el suelo. Para evitar dañar la
estaca, coloque una tabla en la parte superior de la estaca mientras esté
martillando. Si el suelo es duro y es difícil instalar la estaca, haga un corte
cruzado en el suelo usando una pala plana.
3) Limpie el área del suelo en la ranura (B) del canal de alambres la parte
superior de la estaca (A).
4) Coloque el cable de 12 V en la ranura (B) del canal de alambres y atornille el
vástago (D) en la estaca (A). Si el conjunto no se ve derecho, ajuste empu
jando o estirando de la estaca solamente.
5) Instale la lámpara provista (E) en el casquillo, dentro de la cabeza (F) del
artefacto.
6) Pase la cubierta (G) del artefacto encima de la bombilla y ponga arriba del
vástago.
7) Atornille la cubierta del artefacto en el vástago (NO apriete excesivamente.)
8) APAGAR LA ALIMENTACIÓN ELÉCTRICA.
9) Haga las conexiones de cableado usando las tuercas para cables suministrados
siguiendo las instrucciones de la bolsa.
G
E
D
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
G
A
B
  • Page 1 1

Kichler Lighting 15401AZT Manual de usuario

Tipo
Manual de usuario

En otros idiomas