Schumacher SC1280 15A Rapid Charger for Automotive and Marine Batteries El manual del propietario

Categoría
Cargadores de bateria
Tipo
El manual del propietario
0099001990-01
MODEL / MODELO:
SC1280
Automatic Battery Charger
for Marine/Deep-cycle
Cargador de batería automático
para la marina / ciclo profundo
OWNERS MANUAL / MANUAL DEL USUARIO
PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE.
This manual will explain how to use the battery charger safely and effectively.
Please read and follow these instructions and precautions carefully.
POR FAVOR CONSERVE ESTE MANUAL DEL USUARIO Y LEALO ANTES
DE CADA USO. En este manual le explica cómo utilizar el cargador de batería
de manera segura y conable. Por favor, lea y siga las siguientes instrucciones
y precauciones.
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ....................................................................................4
PERSONAL SAFETY PRECAUTIONS .......................................................................................4
PREPARING TO CHARGE .........................................................................................................5
CHARGER LOCATION ................................................................................................................ 5
DC CONNECTION PRECAUTIONS ...........................................................................................5
FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE ...............................5
FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE .......................................6
GROUNDING AND AC POWER CORD CONNECTIONS ........................................................6
ASSEMBLY INSTRUCTIONS ......................................................................................................6
CONTROL PANEL .......................................................................................................................6
OPERATING INSTRUCTIONS .................................................................................................... 7
MAINTENANCE AND CARE .......................................................................................................8
TROUBLESHOOTING/ERROR CODES ....................................................................................9
BEFORE RETURNING FOR REPAIRS ....................................................................................10
SPECIFICATIONS .....................................................................................................................10
LIMITED WARRANTY ...............................................................................................................11
WARRANTY CARD ...................................................................................................................23
CONTENIDOS
INSTRUCCIONES IMPORTANTES DE SEGURIDAD .............................................................12
PRECAUCIONES DE SEGURIDAD PERSONAL ....................................................................12
PREPARACIÓN PARA LA CARGA ..........................................................................................13
UBICACIÓN DEL CARGADOR ................................................................................................. 13
PRECAUCIONES DE CONEXIÓN EN CC ...............................................................................13
SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA EN EL VEHÍCULO ..........13
SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE FUERA DEL VEHÍCULO ...14
CONEXIONES A TIERRA Y ENERGÍA DE CA .........................................................................14
INSTRUCCIONES DE MONTAJE ............................................................................................. 15
PANEL DE CONTROL ...............................................................................................................15
INSTRUCCIONES DE OPERACIÓN ........................................................................................16
MANTENIMIENTO Y CUIDADO ................................................................................................18
LOCALIZACIÓN Y RESOLUCIÓN DE PROBLEMAS Y CODIGOS DE ERROR ....................18
ANTES DE DEVOLVER A REPARACIONES ...........................................................................20
ESPECIFICACIONES ................................................................................................................ 21
GARANTÍA LIMITADA ................................................................................................................21
TARJETA DE GARANTÍA ..........................................................................................................23
4
1. IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
1.1 SAVE THESE INSTRUCTIONS –
This manual contains important safety
and operating instructions.
1.2 This charger is not intended for use by
children.
1.3 Do not expose the charger to rain or snow.
1.4 Use of an attachment not recommended
or sold by the battery charger
manufacturer may result in a risk of re,
electric shock or injury to persons.
1.5 To reduce the risk of damage to electric
plug and cord, pull by the plug rather than
the cord when disconnecting charger.
1.6 An extension cord should not be used
unless absolutely necessary. Use of
improper extension cord could result
in a risk of re and electric shock. If an
extension cord must be used, make sure:
• That the pins on plug of extension cord
are the same number, size and shape as
those of plug on charger.
• That extension cord is properly wired and
in good electrical condition
• That wire size is large enough for AC
ampere rating of charger as specied in
section 8.
1.7 Do not operate charger with damaged
cord or plug – replace the cord or plug
immediately.
1.8 Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualied
serviceman.
1.9 Do not disassemble charger; take it to
a qualied serviceman when service or
repair is required. Incorrect reassembly
may result in a risk of electric shock or re.
1.10 To reduce risk of electric shock, unplug
charger from outlet before attempting
any maintenance or cleaning. Turning off
controls will not reduce this risk.
1.11 WARNING:
RISK OF EXPLOSIVE GASES.
a. WORKING IN VICINITY OF A LEAD-
ACID BATTERY IS DANGEROUS.
BATTERIES GENERATE EXPLOSIVE
GASES DURING NORMAL BATTERY
OPERATION. FOR THIS REASON, IT IS
OF UTMOST IMPORTANCE THAT YOU
FOLLOW THE INSTRUCTIONS EACH
TIME YOU USE THE CHARGER.
b. To reduce risk of battery explosion,
follow these instructions and those
published by battery manufacturer
and manufacturer of any equipment
you intend to use in vicinity of battery.
Review cautionary markings on these
products and on engine.
2. PERSONAL SAFETY PRECAUTIONS
2.1 Consider having someone close enough
by to come to your aid when you work
near a lead-acid battery.
2.2 Have plenty of fresh water and soap
nearby in case battery acid contacts skin,
clothing, or eyes.
2.3 Wear complete eye protection and
clothing protection. Avoid touching eyes
while working near battery.
2.4 If battery acid contacts skin or clothing,
wash immediately with soap and water.
If acid enters eye, immediately ood
eye with running cold water for at least
10 minutes and get medical attention
immediately.
2.5 NEVER smoke or allow a spark or ame
in vicinity of battery or engine.
2.6 Be extra cautious to reduce risk of
dropping a metal tool onto battery. It might
spark or short-circuit battery or other
electrical part that may cause explosion.
2.7 Remove personal metal items such as
rings, bracelets, necklaces, and watches
when working with a lead-acid battery. A
lead-acid battery can produce a short-
circuit current high enough to weld a ring
or the like to metal, causing a severe burn.
2.8 Use the charger for charging only
LEAD-ACID (STD, AGM, Gel or deep-
cycle) rechargeable batteries. It is not
recommended for batteries smaller than
24Ah. It is not intended to supply power
to a low voltage electrical system other
than in a starter-motor application. Do not
use battery charger for charging dry-cell
batteries that are commonly used with
home appliances. These batteries may
burst and cause injury to persons and
damage to property.
2.9 NEVER charge a frozen battery.
5
3. PREPARING TO CHARGE
3.1 If necessary to remove battery from
vehicle to charge, always remove
grounded terminal from battery rst. Make
sure all accessories in the vehicle are off,
so as not to cause an arc.
3.2 Be sure area around battery is well
ventilated while battery is being charged.
3.3 Clean battery terminals. Be careful to
keep corrosion from coming in contact
with eyes.
3.4 Add distilled water in each cell until
battery acid reaches level specied by
battery manufacturer. Do not overll. For a
battery without removable cell caps, such
as valve regulated lead acid batteries,
carefully follow manufacturer’s recharging
instructions.
3.5 Study all battery manufacturer’s
specic precautions while charging and
recommended rates of charge.
3.6 Determine voltage of battery by referring
to car owner’s manual and make sure that
output voltage selector switch is set at
correct voltage. If charger has adjustable
charge rate, charge battery initially at
lowest rate.
4. CHARGER LOCATION
4.1 Locate charger as far away from battery
as DC cables permit.
4.2 Never place charger directly above
battery being charged; gases from battery
will corrode and damage charger.
4.3 Never allow battery acid to drip on
charger when reading electrolyte specic
gravity or lling battery.
4.4 Do not operate charger in a closed-in
area or restrict ventilation in any way.
4.5 Do not set a battery on top of charger.
5. DC CONNECTION PRECAUTIONS
5.1 Connect and disconnect DC output clips
only after setting any charger switches to
“off” position and removing AC cord from
electric outlet. Never allow clips to touch
each other.
5.2 Attach clips to battery and chassis, as
indicated in sections 6 and 7.
6. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE
WARNING: A SPARK NEAR THE
BATTERY MAY CAUSE A BATTERY
EXPLOSION. TO REDUCE THE RISK OF
A SPARK NEAR THE BATTERY:
6.1 Position AC and DC cords to reduce risk
of damage by hood, door, or moving
engine part.
6.2 Stay clear of fan blades, belts, pulleys, and
other parts that can cause injury to persons.
6.3 Check polarity of battery posts. POSITIVE
(POS, P, +) battery post usually has larger
diameter than NEGATIVE (NEG, N,–) post.
6.4 Determine which post of battery is
grounded (connected) to the chassis. If
negative post is grounded to chassis (as
in most vehicles), see (6.5). If positive
post is grounded to the chassis, see (6.6).
6.5 For negative-grounded vehicle, connect
POSITIVE (RED) clip from battery charger
to POSITIVE (POS, P, +) ungrounded post
of battery. Connect NEGATIVE (BLACK)
clip to vehicle chassis or engine block
away from battery. Do not connect clip to
carburetor, fuel lines, or sheet-metal body
parts. Connect to a heavy gauge metal
part of the frame or engine block.
6.6 For positive-grounded vehicle, connect
NEGATIVE (BLACK) clip from battery
charger to NEGATIVE (NEG, N, –)
ungrounded post of battery. Connect
POSITIVE (RED) clip to vehicle chassis
or engine block away from battery. Do
not connect clip to carburetor, fuel lines,
or sheet-metal body parts. Connect to a
heavy gauge metal part of the frame or
engine block.
6.7 When disconnecting charger, turn
switches to off, disconnect AC cord,
remove clip from vehicle chassis, and
then remove clip from battery terminal.
6.8 See Operating Instructions for length of
charge information.
6
7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE
WARNING: A SPARK NEAR THE
BATTERY MAY CAUSE A BATTERY
EXPLOSION. TO REDUCE THE RISK OF
A SPARK NEAR THE BATTERY:
7.1 Check polarity of battery posts. POSITIVE
(POS, P, +) battery post usually has a larger
diameter than NEGATIVE (NEG, N, –) post.
7.2 Attach at least a 24-inch-long 6-gauge
(AWG) insulated battery cable to
NEGATIVE (NEG, N, –) battery post.
7.3 Connect POSITIVE (RED) charger clip to
POSITIVE (POS, P, +) post of battery.
7.4 Position yourself and free end of cable as
far away from battery as possible – then
connect NEGATIVE (BLACK) charger clip
to free end of cable.
7.5 Do not face battery when making nal
connection.
7.6 When disconnecting charger, always do
so in reverse sequence of connecting
procedure and break rst connection
while as far away from battery as
practical.
7.7 A marine (boat) battery must be removed
and charged on shore. To charge it on
board requires equipment specially
designed for marine use.
8. GROUNDING AND AC POWER CORD CONNECTIONS
8.1 This battery charger is for use on a
nominal 120 volt circuit. The plug must
be plugged into an outlet that is properly
installed and grounded in accordance with
all local codes and ordinances. The plug
pins must t the receptacle (outlet). Do
not use with an ungrounded system.
8.2 DANGER: Never alter the AC cord or
plug provided – if it does not t the outlet,
have a proper grounded outlet installed
by a qualied electrician. An improper
connection can result in a risk of an
electric shock or electrocution.
NOTE: Pursuant to Canadian
Regulations, use of an adapter plug
is not allowed in Canada. Use of an
adapter plug in the United States is not
recommended and should not be used.
8.3 USING AN EXTENSION CORD
The use of an extension cord is not
recommended. If you must use an
extension cord, follow these guidelines:
• Pins on plug of extension cord must be
the same number, size, and shape as
those of plug on charger.
Ensure that the extension cord is properly
wired and in good electrical condition.
Wire size must be large enough for the AC
ampere rating of charger, as specied:
Length of cord (feet) 25 50 100 150
AWG* size of cord 18 18 16 14
*AWG-American Wire Gauge
9. ASSEMBLY INSTRUCTIONS
9.1 Remove all cord wraps and uncoil the cables prior to using the battery charger.
10. CONTROL PANEL
START/STOP BUTTON
Press to immediately begin charging your
properly connected battery. If the button
is not pressed, charging should begin
in ten minutes.
CHARGING STATUS LED INDICATORS
CHARGING (yellow/orange) LED lit:
The charger is charging the battery.
CHARGED (green) LED lit:
The battery is fully charged and the
charger is in maintain mode.
CLAMPS REVERSED (red) LED
ashing: The connections are reversed.
BAD BATTERY (red) LED lit: The
charger has detected a problem with the
battery. See Troubleshooting for more
information.
NOTE: See Operating Instructions for a
complete description of the charger modes.
DIGITAL DISPLAY
The display will show the battery VOLTAGE
when the charger is not charging a battery.
When it goes into charging mode, the
display will automatically change to ON (to
show charging has started) and then show
the percent-of-charge of the battery being
charged and either 6 or 12 (the voltage of
the battery, determined by the charger). If
you manually stop the charging process (by
pressing the START/STOP button) before
the battery is fully charged, the display will
show OFF.
NOTE: During charging, the display will
go into sleep mode and will not show the
percentage of charge or voltage of the battery.
To turn the display back on, press any button.
7
Voltage – The Digital Display shows the
voltage at the charger battery clamps in
DC volts, or the voltage of the battery,
depending on what mode the charger is in.
% – The Digital Display shows an
estimated charge percent of the battery
connected to the charger battery clamps.
CHARGE RATE
The charger will automatically adjust the
charging current, based on battery size,
in order to charge the battery completely,
efciently and safely.
RATE SELECTION BUTTON
Use this button to set the maximum
charge rate. Press the button until the
desired charge rate is selected.
3AFor charging small batteries, such as
those commonly used in garden tractors,
snowmobiles and motorcycles. Also used
to maintain fully charged large batteries.
• 15A – For charging automotive, marine
and light truck batteries. Not intended for
industrial applications.
BATTERY TYPE BUTTON
Use this button to select the battery type.
Standard – Used in cars, trucks and
motorcycles, these batteries have
vent caps and are often marked “low
maintenance” or “maintenance-free”.
This type of battery is designed to
deliver quick bursts of energy (such as
starting engines) and has a greater plate
count. The plates are thinner and have
somewhat different material composition.
Standard batteries should not be used for
deep-cycle applications.
AGM – The Absorbed Glass Mat
construction allows the electrolyte to
be suspended in close proximity with
the plate’s active material. In theory,
this enhances both the discharge and
recharge efciency. The AGM batteries
are a variant of Sealed VRLA (valve
regulated lead-acid) batteries. Popular
uses include high-performance engine
starting, power sports, deep-cycle, solar
and storage batteries.
GEL – The electrolyte in a GEL cell has
a silica additive that causes it to set up
or stiffen. The recharge voltages on this
type of cell are lower than those for other
styles of lead-acid battery. This is probably
the most sensitive cell in terms of adverse
reactions to overvoltage charging. Gel
batteries are best used in VERY DEEP
cycle application and may last a bit longer
in hot weather applications. If the wrong
battery charger is used on a gel cell
battery, poor performance and premature
failure will result.
11. OPERATING INSTRUCTIONS
WARNING: A spark near the battery may
cause an explosion.
IMPORTANT: Do not start the vehicle with
the charger connected to the AC outlet, or
it could result in damage to the charger
NOTE: This charger is equipped with
an auto-start feature. Current will not be
supplied to the battery clamps until a
battery is properly connected. The clamps
will not spark if touched together.
CHARGING A BATTERY
IN THE VEHICLE
1. Turn off all the vehicle’s accessories.
2. Keep the hood open.
3. Clean the battery terminals.
4. Place the charger on a dry, non-
ammable surface.
5. Lay the AC/DC cables away from any
fan blades, belts, pulleys and other
moving parts.
6. Connect the battery, following the
precautions listed in sections 6 and 7.
7. Connect the charger to a live grounded
AC outlet.
8. Select the battery type and charge rate.
9. Charging will begin within ten minutes
and nish automatically. (Press the
START/STOP button to begin charging
immediately.)
10. When charging is complete,
disconnect the charger from the AC
power, remove the clamps from the
vehicle’s chassis, and then remove
the clamp from the battery terminal.
CHARGING A BATTERY OUTSIDE
OF THE VEHICLE
1. Place battery in a well-ventilated area.
2. Clean the battery terminals.
3. Connect the battery, following the
precautions listed in sections 6 and 7.
4. Connect the charger to a live grounded
AC outlet.
5. Select the battery type and charge rate.
6. Charging will begin within ten minutes
and nish automatically. (Press the
START/STOP button to begin charging
immediately.)
7. When charging is complete,
disconnect the charger from the AC
power, disconnect the negative clamp,
and nally the positive clamp.
8. A marine (boat) battery must be
removed and charged on shore.
AUTOMATIC CHARGING MODE
When an Automatic Charge is performed,
the charger switches to the maintain mode
automatically after the battery is charged.
8
BATTERY CHARGING TIMES
APPLICATION
BATTERY
SIZE
CHARGING TIME (Hours)
6A 8A 10A 15A
POWERSPORTS
6Ah 2
32 Ah 5
AUTOMOTIVE
300 CCA 4
1000 CCA 10
MARINE
50 Ah 5
105Ah 11
1.5
4.5
3.5
8
4
10
1.5
4
3
7
3.5
8
1
2
1. 5
4
2
5
Times are based on a 50% discharged
battery and may change, depending on age
and condition of battery.
ABORTED CHARGE
If charging cannot be completed normally,
charging will abort. When charging aborts,
the chargers output is shut off and the BAD
BATTERY (red) LED will light. The digital
display will show an error code (see the
Troubleshooting section for a description of
the error codes). Do not continue attempting
to charge this battery. Check the battery and
replace, if necessary.
DESULFATION MODE
Desulfation could take 8 to 10 hours.
During this time, the display will show “SUL
and the BAD BATTERY (red) LED will
light. If desulfation fails, charging will abort,
the display will show “F02” and the BAD
BATTERY (red) LED will stay on.
COMPLETION OF CHARGE
Charge completion is indicated by the
CHARGED (green) LED. When lit, the
charger has switched to the maintain
mode of operation.
MAINTAIN MODE
(FLOAT-MODE MONITORING)
When the CHARGED (green) LED is lit, the
charger has started maintain mode. In this
mode, the charger keeps the battery fully
charged by delivering a small current when
necessary. If the charger has to provide its
maximum maintain current for a continuous
12 hour period, it will go into abort mode
(see Aborted Charge section). This is
usually caused by a drain on the battery or
the battery could be bad. Make sure there
are no loads on the battery. If there are,
remove them. If there are none, have the
battery checked or replaced.
MAINTAINING A BATTERY
The SC1280 charges and maintains 6-volt
and 12-volt batteries.
NOTE: The maintain mode technology
allows you to safely charge and maintain
a healthy battery for extended periods of
time. However, problems with the battery,
electrical problems in the vehicle, improper
connections or other unanticipated
conditions could cause excessive current
draws. As such, occasionally monitoring your
battery and the charging process is required.
USING THE BATTERY VOLTAGE TESTER
1. With the charger unplugged from the
AC outlet, connect the charger to the
battery following the instructions given
in previous sections.
2. Plug the charger AC power cord into
the AC outlet.
3. If necessary, press the BATTERY TYPE
button until the correct type is indicated.
4. Read the voltage on the digital display.
Keep in mind that this reading is only a
battery voltage reading; a false surface
charge may mislead you. Compare the
reading to the chart below.
6 V Battery
Voltage
Reading
12 V Battery
Voltage
Reading
Battery
Condition
6.4 or More 12.8 or More Charged
6.1 to 6.3 12.2 to 12.7 Needs Charging
Less than 6.1 Less than 12.2 Discharged
POWER-UP IDLE TIME LIMIT
If no button is pressed within 30 seconds
after the battery charger is rst powered up,
the charger will automatically switch from
tester to charger if a battery is connected. In
that case, the charger will be set to charge
at the 15A rate and AGM battery type.
12. MAINTENANCE AND CARE
A minimal amount of care can keep your
battery charger working properly for years.
• Clean the clamps each time you are
nished charging. Wipe off any battery
uid that may have come in contact with
the clamps to prevent corrosion.
• Occasionally cleaning the case of the
charger with a soft cloth will keep the
nish shiny and help prevent corrosion.
Coil the input and output cords neatly
when storing the charger. This will help
prevent accidental damage to the cords
and charger.
• Store the charger unplugged from the AC
power outlet in an upright position.
Store inside, in a cool, dry place. Do not
store the clamps clipped together, on or
around metal, or clipped to the cables.
9
13. TROUBLESHOOTING/ERROR CODES
Error Codes
ERROR
CODE
DESCRIPTION REASON/SOLUTION
F 01
The battery voltage is still under
10V (for a 12V battery) or 5V
(for a 6V battery) after 2 hours of
charging.
The battery could be bad. Have it checked or
replaced.
F02
The charger cannot desulfate the
battery.
The battery could not be desulfated; have it
checked or replaced.
F03
The battery was unable to reach
the “full charge” voltage.
May be caused by trying to charge a large battery
or bank of batteries on too low of a current setting.
Try again with a higher current setting or have the
battery checked or replaced.
F04
The connections to the battery
are reversed.
The battery is connected backwards. Unplug the
charger and reverse the connections to the battery.
F05
The charger was unable to
keep the battery fully charged in
maintain mode.
The battery won’t hold a charge. May be caused
by a drain on the battery or the battery could be
bad. Make sure there are no loads on the battery.
If there are remove them. If there are none, have
the battery checked or replaced.
F06
The charger detected that the
battery may be getting too hot
(thermal runaway).
The charger automatically shuts the current off if
it detects the battery may be getting too hot. Have
the battery checked or replaced.
If you get an error code, check the connections and settings and/or replace the battery.
Troubleshooting
PROBLEM POSSIBLE CAUSE SOLUTION
Battery clamps do not
spark when touched
together.
The charger is equipped
with an auto-start feature.
It will not supply current to
the battery clamps until a
battery is properly connected.
The clamps will not spark if
touched together.
No problem; this is a normal
condition.
The charger will not
turn on when properly
connected.
AC outlet is dead.
Poor electrical connection.
Battery is defective.
Check for open fuse or circuit
breaker supplying AC outlet.
Check power cord and extension
cord for loose tting plug.
Have battery checked.
I cannot select a 6V or 12V
setting.
The charger is equipped
with Auto Voltage Detection,
which automatically detects
the voltage and charges the
battery.
No problem; this is normal.
The battery is correctly
connected, but the
CHARGING LED did not light
immediately.
If the START/STOP button is
not pressed, charging should
begin in ten minutes.
No problem; this is normal.
The battery is properly
connected, but the
CHARGING LED never lit.
The battery voltage is low. Press the START/STOP button
to start charging.
10
PROBLEM POSSIBLE CAUSE SOLUTION
The BAD BATTERY LED
is lit.
The battery voltage is still
below 10V (for a 12V battery)
or 5V (for a 6V battery) after
2 hours of charging.
(or)
In maintain mode, the output
current is more than 1.5A for
12 hours.
Desulfation was
unsuccessful.
Lack of progress is detected
and battery voltage is below
14.2V (for a 12V battery) or
7.1V (for a 6V battery).
The battery’s initial voltage
is below 12.2V (for a 12V
battery) or 6.1V (for a 6V
battery) and the total input is
less than 1.5 Ah.
The battery voltage drops
to below 12.2V (for a 12V
battery) or 6.1V (for a 6V
battery) in Maintain Mode.
The battery may be defective.
Make sure there are no loads
on the battery. If there are,
remove them. If there are none,
have the battery checked or
replaced.
The battery may be defective.
Have battery checked or
replaced.
The battery may be overheated.
If so, allow the battery to cool.
The battery may be too large
or have a short circuit. Have
battery checked or replaced.
The battery capacity is too low,
or the battery is too old. Have it
checked or replaced.
The battery won’t hold a charge.
May be caused by a drain on the
battery or the battery could be
bad. Make sure there are no loads
on the battery. If there are remove
them. If there are none, have the
battery checked or replaced.
14. BEFORE RETURNING FOR REPAIRS
If these solutions do not eliminate the problem, or for more information
about troubleshooting, contact customer service for assistance:
www.batterychargers.com
or call 1-800-621-5485
For REPAIR OR RETURN, contact Customer Service at 1-800-621-5485. DO NOT SHIP
UNIT until you receive a RETURN MERCHANDISE AUTHORIZATION (RMA) number
from Customer Service at Schumacher Electric Corporation.
15. SPECIFICATIONS
Input Voltage ..................................................................................120V AC
@
60Hz, 3.6A
Output Voltage ........................................................6V or 12V, with auto voltage detection
Output Current Rating ..............................................2A DC
@
6V DC; 15A DC
@
12V DC
11
16. LIMITED WARRANTY
WARRANTY NOT VALID IN MEXICO.
SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,
MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO THE
ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED WARRANTY
IS NOT TRANSFERABLE OR ASSIGNABLE.
Schumacher Electric Corporation (the “Manufacturer”) warrants this battery charger
for two (2) years from the date of purchase at retail against defective material or
workmanship that may occur under normal use and care. If your unit is not free from
defective material or workmanship, Manufacturer’s obligation under this warranty is
solely to repair or replace your product with a new or reconditioned unit at the option
of the Manufacturer. It is the obligation of the purchaser to forward the unit, along with
proof of purchase and mailing charges prepaid to the Manufacturer or its authorized
representatives in order for repair or replacement to occur.
Manufacturer does not provide any warranty for any accessories used with this product
that are not manufactured by Schumacher Electric Corporation and approved for use
with this product. This Limited Warranty is void if the product is misused, subjected to
careless handling, repaired, or modied by anyone other than Manufacturer or if this
unit is resold through an unauthorized retailer.
Manufacturer makes no other warranties, including, but not limited to, express, implied or
statutory warranties, including without limitation, any implied warranty of merchantability or
implied warranty of tness for a particular purpose. Further, Manufacturer shall not be liable
for any incidental, special or consequential damage claims incurred by purchasers, users
or others associated with this product, including, but not limited to, lost prots, revenues,
anticipated sales, business opportunities, goodwill, business interruption and any other
injury or damage. Any and all such warranties, other than the limited warranty included
herein, are hereby expressly disclaimed and excluded. Some states do not allow the
exclusion or limitation of incidental or consequential damages or length of implied warranty,
so the above limitations or exclusions may not apply to you. This warranty gives you specic
legal rights and it is possible you may have other rights which vary from this warranty.
THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND THE
MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO ASSUME
OR MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT OTHER THAN
THIS WARRANTY.
Schumacher
®
and the Schumacher logo are registered trademarks
of Schumacher Electric Corporation.
12
1. INSTRUCCIONES IMPORTANTES DE SEGURIDAD
GUARDE ESTAS INSTRUCCIONES.
1.1 GUARDE ESTAS INSTRUCCIONES –
Este manual contiene instrucciones
operativas y de seguridad de importancia.
1.2 Este cargador no está destinado para ser
usado por niños.
1.3 No exponga el cargador a la lluvia
o a la nieve.
1.4 El uso de un accesorio no recomendado
o suministrado por por el fabricante del
cargador de baterías puede provocar
riesgo de incendio, descarga eléctrica o
lesiones a personas.
1.5 Para reducir el riesgo de daños al
enchufe o cable eléctrico, jale del enchufe
en lugar de jalar del cable al desconectar
el cargador.
1.6 No se debe utilizar un alargador a menos
que resulte absolutamente necesario. El
uso de un alargador inadecuado puede
provocar riesgo de incendio o descarga
eléctrica. En caso de que deba utilizarse
un alargador, asegúrese de que:
• Los pasadores en el enchufe del
alargador posean el mismo número,
tamaño y forma que aquellos presentes
en el enchufe del cargador.
• El alargador se encuentre correctamente
conectado y en buenas condiciones
eléctricas
• El tamaño del cable sea lo
sucientemente extenso para el
amperaje en CA del cargador como se
especica en la sección 8.
1.7 No utilice el cargador si el mismo posee
un enchufe o cable dañado; substituya el
cable o el enchufe inmediatamente por
una persona calicada en el ramo.
1.8 No utilice el cargador si el mismo recibió
un golpe fuerte, si se cayó o si sufrió
daños de cualquier otra forma; hágalo
revisar por una persona capacitada que
efectúe reparaciones.
1.9 No desarme el cargador; hágalo revisar
por una persona capacitada que efectúe
reparaciones cuando necesite servicio
de mantenimiento o una reparación.
Volver a ensamblar el cargador en forma
incorrecta puede provocar riesgo de
incendio o descarga eléctrica.
1.10 Para reducir el riesgo de descarga
eléctrica, desenchufe el cargador del
tomacorriente antes de intentar llevar a
cabo cualquier actividad de mantenimiento
o limpieza. El simple apagado de los
controles no reducirá este riesgo.
1.11 ADVERTENCIA:
RIESGO DE GASES EXPLOSIVOS.
a. RESULTA PELIGROSO TRABAJAR EN
FORMA CERCANA A UNA BATERÍA DE
PLOMO. LAS BATERÍAS GENERAN
GASES EXPLOSIVOS DURANTE
SU NORMAL FUNCIONAMIENTO.
POR ESTE MOTIVO, RESULTA DE
SUMA IMPORTANCIA QUE SIGA LAS
INSTRUCCIONES CADA VEZ QUE
UTILIZA EL CARGADOR.
b. Para reducir el riesgo de explosión de
una batería, siga estas instrucciones y
aquellas publicadas por el fabricante
de la batería y por el fabricante de
cualquier equipo que intente utilizar
en la proximidad de la batería. Revise
las pautas de precaución en estos
productos y en el motor.
2. PRECAUCIONES DE SEGURIDAD PERSONAL
2.1 Considere la idea de que alguna persona
se encuentre cerca suyo para poder
ayudarlo cuando trabaje en forma
cercana a una batería de plomo-ácido.
2.2 Cuente con una gran cantidad de agua
potable y jabón a mano en caso de que el
ácido de la batería tenga contacto con su
piel, ropa u ojos.
2.3 Utilice protección visual y corporal completa,
incluyendo gafas de seguridad y prendas
de protección. Evite tocar sus ojos mientras
trabaje en forma cercana a la batería.
2.4 Si el ácido de la batería tiene contacto con
su piel o su ropa, lave de inmediato el área
afectada con agua y jabón. En caso de que
ingrese ácido en un ojo, sumerja el mismo
de inmediato bajo agua potable corriente
por al menos 10 minutos y obtenga
atención médica en forma inmediata.
2.5 NUNCA fume o permita la presencia de
chispas o llamas en la proximidad de una
batería o motor.
2.6 Tenga especial cuidado para reducir el
riesgo de dejar caer una herramienta
de metal sobre la batería. Esto podría
provocar chispas o un cortocircuito en la
batería o en cualquier otra pieza eléctrica
que podría provocar una explosión.
2.7 No utilice elementos personales de metal
tales como anillos, pulseras, collares y
relojes al trabajar con una batería de
plomo-ácido. Una batería de plomo-
ácido puede producir una corriente de
cortocircuito lo sucientemente elevada
13
como para soldar un anillo o provocar
efectos similares sobre el metal,
causando una quemadura de gravedad.
2.8 Utilice este cargador solamente para
cargar baterías de 6V y 12V de tipo
PLOMO-ÁCIDO (estándar, AGM, GEL o
ciclo-profundo). No se recomienda para
baterías más pequeñas que 24Ah. Este
cargador no está destinado a suministrar
energía a sistemas eléctricos de baja
tensión más que en una aplicación de
un motor de arranque. No utilice este
cargador de batería para cargar baterías
de pila seca que por lo general se utilizan
con artefactos domésticos. Estas baterías
podrían explotar y provocar lesiones a
personas o daño a la propiedad.
2.9 NUNCA cargue una batería congelada.
3. PREPARACIÓN PARA LA CARGA
3.1 Si resulta necesario extraer la batería
del vehículo para cargarla, siempre retire
el terminal con descarga a tierra en
primer lugar. Asegúrese de que todos los
accesorios en el vehículo se encuentren
apagados para evitar la formación de
arcos eléctricos.
3.2 Asegúrese de que el área que rodea a
la batería se encuentre bien ventilada
mientras se carga la batería.
3.3 Limpie los terminales de la batería antes
de cargar la batería. Durante la limpieza,
evite que la corrosión producida por aire
tenga contacto con sus ojos.
3.4 Agregue agua destilada a cada pila hasta
que el ácido de la batería alcance el
nivel especicado por el fabricante de la
batería. No provoque derrames. En lo que
concierne a baterías que no cuentan con
tapas extraíbles para pilas, tales como
baterías de plomo-ácido reguladas por
válvulas (VRLA, por sus siglas en inglés),
siga cuidadosamente las instrucciones de
recarga del fabricante.
3.5 Lea, comprenda y siga todas las
instrucciones para el cargador, la batería,
el vehículo y cualquier equipo que se
utilice cerca de la batería y el cargador.
Controle todas las precauciones
especícas establecidas por el fabricante
de la batería al realizar la carga, así
también como los índices de carga
recomendados.
3.6 Determine la tensión de la batería al
consultar el manual del usuario del
vehículo y asegúrese de que el interruptor
de selección de la tensión de salida
se encuentre establecido en la tensión
correcta (en su caso). Si el cargador posee
un índice de carga ajustable, cargue la
batería en el menor índice en primer lugar.
4. UBICACIÓN DEL CARGADOR
4.1 Ubique el cargador a la mayor distancia
posible de la batería como lo permitan los
cables de CC.
4.2 Nunca ubique el cargador directamente
por encima de la batería que se carga; los
gases de la batería corroerán y dañarán
el cargador.
4.3 Nunca permita que el ácido de la batería
gotee sobre el cargador al leer el peso
especíco del electrolito o al cargar la
batería.
4.4 No utilice el cargador en un área cerrada o
restrinja la ventilación en cualquier forma.
4.5 No ubique la batería encima del cargador.
5. PRECAUCIONES DE CONEXIÓN EN CC
5.1 Conecte y desconecte las pinzas de
salida CC. sólo después de haber
establecido todos los interruptores del
cargador a la posición de “apagado” (si
es aplicable) y de haber desconectado
el enchufe de C.A. del tomacorriente
eléctrico. Nunca permita que las pinzas
tengan contacto entre sí.
5.2 Sujete las pinzas a la batería y al chasis,
como se indica en en las secciones 6 y 7.
6. SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA EN EL VEHÍCULO
ADVERTENCIA:
UNA CHISPA PROVOCADA CERCA
DE LA BATERÍA PUEDE CAUSAR LA
EXPLOSIÓN DE LA BATERÍA. PARA
REDUCIR EL RIESGO DE PROVOCAR
CHISPAS CERCA DE LA BATERÍA:
6.1 Ubique los cables de CA y CC
adecuadamente para reducir el riesgo
de daños por la cubierta, la puerta y las
piezas móviles o calientes del motor.
6.2 Manténgase alejado de las paletas del
ventilador, correas, poleas y otras piezas
que podrían provocar lesiones.
14
6.3 Verique la polaridad de los bornes de
la batería. El borne POSITIVO (POS,
P, +) de la batería generalmente posee
un diámetro mayor al borne NEGATIVO
(NEG, N, -).
6.4 Determine qué borne de la batería
hace descarga a tierra (se encuentra
conectado) con el chasis. Si el borne
negativo hace descarga a tierra con el
chasis (como en la mayor parte de los
vehículos), ver el paso (6.5). Si el borne
positivo hace descarga a tierra con el
chasis, ver el paso (6.6).
6.5 En un vehículo con descarga a tierra
por borne negativo, conecte el gancho
POSITIVO (ROJO) del cargador de
batería al borne POSITIVO (POS, P, +) sin
descarga a tierra de la batería. Conecte
el gancho NEGATIVO (NEGRO) al chasis
del vehículo o al bloque motor alejado
de la batería. No conecte el gancho al
carburador, líneas de combustible o
cuerpos metálicos. Conecte a una pieza
metálica de calibre grueso del marco o
del bloque motor.
6.6 En un vehículo con descarga a tierra
por borne positivo, conecte el gancho
NEGATIVO (NEGRO) del cargador de
batería al borne NEGATIVO (NEG, N, -) sin
descarga a tierra de la batería. Conecte el
gancho POSITIVO (ROJO) al chasis del
vehículo o al bloque motor alejado de la
batería. No conecte al carburador, líneas
de combustible o cuerpos metálicos.
Conecte a una pieza metálica de calibre
grueso del marco o del bloque motor.
6.7 Al desconectar el cargador, apague todos
los interruptores (en su caso), desconecte
el cable de C.A., retire el gancho del
chasis del vehículo y luego retire el gancho
del terminal perteneciente a la batería.
6.8 Vea Instrucciones de Operación para
duración de la carga.
7. SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE FUERA DEL VEHÍCULO
ADVERTENCIA:
UNA CHISPA PROVOCADA CERCA
DE LA BATERÍA PUEDE CAUSAR LA
EXPLOSIÓN DE LA BATERÍA. PARA
REDUCIR EL RIESGO DE PROVOCAR
CHISPAS CERCA DE LA BATERÍA:
7.1 Verique la polaridad de los bornes de
la batería. El borne POSITIVO (POS,
P, +) de la batería generalmente posee
un diámetro mayor al borne NEGATIVO
(NEG, N, -).
7.2 Sujete al menos un cable aislado de batería
de 24 pulgadas (61 cm) de largo con calibre
6 según el Calibre americano de cables
(AWG, por sus siglas en inglés) al borne
NEGATIVO (NEG, N, -) de la batería.
7.3 Conecte el gancho POSITIVO (ROJO) del
cargador al borne POSITIVO (POS, P, +)
de la batería.
7.4 Ubíquese junto con el extremo libre del
cable que previamente sujetó al borne
NEGATIVO (NEG, N, -) de la batería a
la mayor distancia posible de la batería.
Luego conecte el gancho NEGATIVO
(NEGRO) del cargador al extremo libre
del cable.
7.5 No se ubique en posición frontal a la
batería al realizar la conexión nal.
7.6 Al desconectar el cargador, siempre
hágalo en forma inversa al procedimiento
de conexión y realice la primera conexión
tan lejos de la batería como sea posible.
7.7 Una batería marina (para barcos) se
debe retirar y cargar en tierra. Para
realizar una carga a bordo se necesitan
equipamientos especialmente diseñados
para uso marino.
8. CONEXIONES A TIERRA Y ENERGÍA DE CA
8.1 Este cargador de batería está destinado a
un uso en un circuito con tensión nominal
de 120 V. El enchufe se debe conectar
a un tomacorriente adecuadamente
instalado y que cuente con descarga
a tierra de acuerdo con todas las
ordenanzas y códigos. Los pasadores del
enchufe deben adaptarse al receptáculo
(tomacorriente). No utilizar con un
sistema que no posea descarga a tierra.
8.2 PELIGRO: Nunca altere el cable o
enchufe de C.A. suministrado, si no se
ajusta al tomacorriente, haga instalar un
tomacorriente adecuado con descarga
a tierra por medio de un electricista
capacitado. Una conexión inadecuada
puede provocar un riesgo de descarga
eléctrica o electrocución.
NOTA: De acuerdo a las Leyes
Canadienses, el uso de un enchufe
adaptador no es permitido en el Canada.
El uso de un enchufe como adaptador
no se recomienda y no debe ser utilizado
Estados Unidos.
15
8.3 USO DE UN CABLE DE EXTENSIÓN
El uso de una extensión no se
recomienda. Si debe usar una extensión,
siga estas pautas:
• Las clavijas del enchufe del cable de
extensión debe ser el mismo número,
tamaño y forma que las del enchufe del
cargador.
Asegúrese de que el cable de extensión
esté conectado correctamente y en
buenas condiciones eléctricas.
• El tamaño del cable debe ser lo
sucientemente extenso para el calibre
de amperios del cargador de CA, como
se especica a continuación:
Longitud del cable (pies)
25 50 100 150
Calibre del cable AWG*
18 18 16 14
*AWG-American Wire Gauge
9. INSTRUCCIONES DE MONTAJE
9.1 Desenrede todos los cordones y extienda los cables antes de usar el cargador de baterías.
10. PANEL DE CONTROL
BOTÓN DE START/STOP (inicio / parada)
Pulse para comenzar inmediatamente
la carga de su batería conectada
correctamente. Si no se presiona el botón,
la carga debe comenzar en diez minutos.
INDICADORES LED PARA ESTADO
DE LA CARGA
LED CHARGING (carga) [amarillo /
naranja] encendido: El cargador está
cargando la batería.
LED CHARGED (cargado) [verde]
encendido: La carga de la bateria está
completa y que el cargador cambió a
modo mantener.
LED CLAMPS REVERSED
(pinzas invertidas) [rojo] parpadea:
Las conexiones están inversas.
LED BAD BATTERY (mala batería) [rojo]
encendido: El cargador ha detectado
un problema con la batería. Consulte
Localización y Solución de Problemas para
más información.
NOTA: Consulte la sección Instrucciones
de Operación para obtener una descripción
completa de los modos del cargador.
PANTALLA DIGITAL
La pantalla digital proporciona una
indicación digital de la tensión o % de
carga. La pantalla mostrará el VOLTAJE
de la batería cuando el cargador no
se encuentre cargandola. Cuando
se programe en el modo de carga, la
carátula cambiará automáticamente a On
(encendido–para mostrar que la carga
ha comenzado) y después mostrará el
porcentaje-de-carga obtenido por la batería.
y asi indicado 6 o 12 (el voltaje de carga
que el cargador haya detectado en la
batería. Si usted, manualmente detiene el
proceso de carga (una vez que presiona
el botón de START / STOP antes que la
batería esté completamente cargada, la
carátula se Off (apagara).
NOTA: Durante la carga, la pantalla entra
en el modo de suspensión y no se mostrará
el porcentaje de carga o la tensión de la
batería. Para activar la pantalla, pulse
cualquier botón.
Voltage (tensión) – La pantalla digital
muestra la tensión en las pinzas de
batería pertenecientes al cargador en
volts de C.C., o el voltaje que el cargador
determina en la batería, es dependiendo
en qué modo está.
% – La pantalla digital muestra un
porcentaje de carga estimado de la
batería conectada a los ganchos de
batería pertenecientes al cargador.
VELOCIDAD DE CARGA
El cargador se ajusta automáticamente la
corriente de carga, basado en el tamaño
de la batería, con el n de cargar la batería
completamente, eciente y segura.
BOTÓN DE RATE SELECTION
(SELECCIÓN DE VELOCIDAD)
Utilice este botón para ajustar la velocidad
de carga máxima. Pulse el botón hasta
que el nivel de carga deseado.
3APara cargar baterías pequeñas,
tales como los comúnmente utilizados
en tractores de jardín, motos de nieve
y motocicletas. También se utiliza para
mantener las baterías completamente
cargadas de gran tamaño.
15A Para la carga de baterías de
automóviles, camiones marinos y luz.
No está diseñado para aplicaciones
industriales.
BOTÓN DE BATTERY TYPE
(TIPO DE BATERÍA)
Utilice este botón para seleccionar el tipo
de batería.
• Estándar – Este tipo de batería
generalmente se utiliza en automóviles,
camiones y motocicletas. Este tipo
de baterías cuentan con tapas de
16
ventilación y a menudo se las clasica
como de “bajo mantenimiento” o “libre de
mantenimiento”. Este tipo de baterías está
diseñado para suministrar rápidas ráfagas
de energía (tales como los arranques de
motores) y poseen un mayor recuento en
placa. Las placas asimismo serán más
delgadas y poseerán una composición
de materiales algo diferente. Las baterías
regulares no se deben utilizar en
aplicaciones de ciclo profundo.
AGM – La construcción de la malla de
bra de vidrio absorbente permite la
suspensión del electrolito en extrema
proximidad con el material activo de la
placa. En teoría, esto aumenta tanto la
eciencia de la descarga como de la
recarga. Las baterías AGM constituyen
una variedad de las baterías Selladas
VRLA (de plomo-ácido reguladas por
válvula). Entre sus usos más comunes
se encuentran baterías con arranque de
motor de alto rendimiento, para deportes
intensos, de ciclo profundo, solares y de
acumuladores.
GEL – El electrolito en una celda de gel
de sílice tiene un aditivo que hace que
se congura o endurecer. Los voltajes
de recarga de este tipo de células son
más bajos que los de los otros estilos
de la batería de plomo-ácido. Ésta es
probablemente la célula más sensible en
términos de las reacciones adversas a la
carga de sobretensión. Las baterías de
gel son los más utilizados en aplicaciones
de ciclos MUY PROFUNDOS y puede
durar un poco más en aplicaciones en
clima caliente. Si el cargador de baterías
incorrecto se utiliza con una batería de
celda de gel, bajo rendimiento y el fracaso
prematuro como resultado.
11. INSTRUCCIONES DE OPERACIÓN
ADVERTENCIA: Una chispa provocada
cerca de la batería puede causar la
explosión de la batería.
IMPORTANTE: No arranque el vehículo
con el cargador conectado a la toma
de CA, o puede resultar en daños al
cargador.
NOTA: Este cargador está equipado
con un auto-recticador. La corriente no
llegará a las pinzas de la batería hasta
que la batería esté apropiadamente
conectada. Signicado, las pinzas no
harán corto si se juntan una con otra.
CARGA DE LA BATERÍA
EN EL VEHÍCULO
1. Apague todos los accesorios del
vehículo.
2. Mantenga el cofre abierto.
3. Limpie las terminales de la batería.
4. Coloque el cargador sobre una
supercie seca y no inamable.
5. Coloque los cables de CA / CC lejos
de las aspas del ventilador, bandas,
poleas y otras partes móviles.
6. Conectar la batería según las
instrucciones que indicadas en las
secciones 6 y 7.
7. Conecte el cargador a un tomacorriente
120 Voltios CA con conexión a tierra.
8. Seleccione el tipo de batería y la
velocidad de carga.
9. La carga comenzará dentro de diez
minutos y terminar de forma automática.
(Pulse el botón START / STOP para
iniciar la carga de inmediato.)
10. Cuando la carga está completa,
desconecte el cargador de la
alimentación de CA, retire la pinza del
chasis del vehículo y quite la pinza de
la terminal de la batería.
CARGA DE LA BATERÍA
FUERA DEL VEHÍCULO
1. Coloque la batería un área bien
ventilada.
2. Limpie las terminales de la batería.
3. Conectar la batería según las
instrucciones que indicadas en las
secciones 6 y 7.
4. Conecte el cargador a un tomacorriente
120 Voltios CA con conexión a tierra.
5. Seleccione el tipo de batería y la
velocidad de carga.
6. La carga comenzará dentro de diez
minutos y terminar de forma automática.
(Pulse el botón START / STOP para
iniciar la carga de inmediato.)
7. Cuando la carga está completa,
desconecte el cargador de la corriente
AC, desconecte la pinza negativa, y
por último la pinza positiva.
8. Una batería marina (de barco) se
debe retirar y cargar en tierra.
MODO DE CARGA AUTOMÁTICA
Cuando se realiza una carga automática,
el cargador cambia del maintain
mode [modo de mantenimiento] (ver a
continuación) automáticamente después
que la batería se cargue.
17
TIEMPOS DE CARGA
APLICACIÓN
TAMAÑO DE
LA BATERÍA
TIEMPO DE CARGA (Horas)
6A 8A 10A 15A
POWERSPORTS
6Ah 2
32 Ah 5
AUTOMOTOR
300 CCA 4
1000 CCA 10
MARINA
50 Ah 5
105Ah 11
1, 5
4,5
3, 5
8
4
10
1, 5
4
3
7
3, 5
8
1
2
1, 5
4
2
5
Times are based on a 50% discharged
battery and may change, depending on age
and condition of battery.
CARGA ANULADA
Si no se puede completar la carga
normalmente, la carga se anulará.
Cuando la carga se interrumpe, la salida
del cargador se apaga y la luz LED
(rojo) BAD BATTERY se encenderá.
El indicador digital mostrará un código
de error (véase la sección Localización
y Solución de Problemas para una
descripción de los códigos de error). No
continúe tratando de cargar esta batería.
Compruebe la batería y reemplazar si es
necesario.
MODO DE DESULFATACIÓN
La desulfatación puede durar 8 a 10
horas. Durante este tiempo, la pantalla
mostrará “SUL” y el LED BAD BATTERY
(rojo) se iluminará. Si la desulfatación
falla, la carga se cancelará, la pantalla
mostrará “F02” y el LED BAD BATTERY
(rojo) permanecerá encendido.
FINALIZACIÓN DE LA CARGA
La nalización de la carga se indica con
el LED (verde) CHARGED. Cuando está
encendido, el cargador ha pasado de
modo de función a mantenimiento.
MODO DE MANTENIMIENTO
(MONITOREO A MODO DE FLOTE)
Cuando la luz LED (verde) CHARGED
está encendido, quiere decir que pasó al
modo de mantenimiento. En este modo el
cargador mantiene la batería totalmente
cargada mediante una pequeña corriente
cuando corresponda. Si el cargador tiene
que funcionar al máximo en corriente
continua de mantenimiento a un periodo
de 12 horas, se transladará al Modo
de Interrumpir (véase la sección Carga
Anulada). Esto es ocacionalmente
causado por una pérdida de energía
en la batería o la batería está dañada.
Asegúrese que no escape de carga en
la batería y si la hay evítela, en caso
contrario, verique o reémplace la batería.
MANTENIENDO UNA BATERÍA
El SC1280 carga y mantiene las baterías
de 6 y 12 voltios.
NOTA: La tecnología de modo de
mantenimiento le permite cargar de
forma segura y mantener una batería
en buen estado durante largos períodos
de tiempo. Ahora, los problemas con
la batería, problemas eléctricos del
vehículo, conexiones equivocadas u otras
condiciones que surgan, podrías causar
absorsión de corriente excesiva. De modo
que, ocasionalmente seguimiento de su
batería y el proceso de carga se requiere.
UTILIZAR EL PROBADOR DE TENSIÓN
DE BATERÍA
1. Con el cargador desenchufado del
tomacorriente de C.A., conecte el
cargador a la batería siguiendo las
instrucciones que guran en las
secciones anteriores.
2. Enchufe el cable de alimentación de
C.A. del cargador en el tomacorriente
de C.A.
3. Si fuera necesario, presione el botón
BATTERY TYPE hasta que el tipo
correcto se indique.
4. Lea la tensión de la pantalla digital.
Tenga en cuenta que esta lectura es
solamente una lectura de la tensión
de la batería, una falsa carga de
supercie podría engañarlo. Compare
la lo mostrado con la siguiente gráca.
Indicación
de Voltaje
a 6 Voltios
Indicación
de Voltaje
a 12 Voltios
Condición
de la Batería
6,4 o más 12,8 o más Cargada
6,1 a 6,3 12,2 a 12,7
Necesita ser
cargada
Menos de 6,1 Menos de 12,2 Descargada
ENCENDER EL LÍMITE DE TIEMPO
DE INACTIVIDAD
Si no se presiona un botón dentro de los
30 segundos después de que el cargador
de batería se encendió por primera vez,
el cargador automáticamente cambiará
de probador a cargador si la batería está
conectada. En ese caso, el cargador se
ajustará a la velocidad 15A y de tipo AGM
para la batería.
18
12. MANTENIMIENTO Y CUIDADO
Con cuidados mínimos puede mantener
el cargador de baterías funcionando
correctamente durante años.
• Limpie las pinzas cada vez que termine
de usar el cargador. Limpie el uido de
la batería que podría haber estado en
contacto con las pinzas para evitar la
corrosión.
De vez en cuando, limpie la carcasa
del cargador con un paño suave para
conservar el acabado brillante y evitar la
corrosión.
• Enrolle los cables de entrada y salida
cuidadosamente cuando almacene el
cargador. Esto ayudará a evitar daños
accidentales a los cables y el cargador.
• Guarde el cargador desenchufado de la
toma de alimentación de CA en posición
vertical.
• Debe conservarse en un lugar fresco
y seco. No lo enrede las pinzas en el
mango, no las una, ni en metal, tampoco
sujete a los cables.
13. LOCALIZACIÓN Y RESOLUCIÓN DE PROBLEMAS Y CODIGOS DE ERROR
Codigos de Error
CÓDIGO DESCRIPCIÓN RAZÓN/SOLUCIÓN
F 01
El voltaje de la batería todavía está
debajo de 10V (para una batería
12V) o de 5V (para una batería 6V)
después de 2 horas de carga.
La batería podría estar en malas condiciones.
Verifíquela o reemplácela.
F02
El cargador no puede desulfatar
la batería.
La batería no puede desulfatada.Verifíquela o
reemplácela.
F03
La batería no alcanzó “su carga
completa”, voltaje.
Podría ser causado al intentar cargar una batería
grande o baterías en serie en un ajuste bajo de
energía. Intente otra vez con un ajuste más alto de
corriente o verifíque o reempláce la batería.
F04
Las conexiones a la batería están
invertidas.
La batería está conectada en forma inversa.
Desconecte el cargador y haga la conexión en
forma correcta.
F05
El cargador no puede alimentar
la batería cargada el el modo de
mantenimiento.
La batería no mantiene la carga. Podría ser
causado por un escape en la batería o la batería
podría estar en malas condiciones. Cerciórese
de que no haya fugas en la batería. Si no hay
ninguno, verifíque o reempláce la batería.
F06
El cargador ha detectado que la
batería se está sobrecalentando
(fuga térmica).
El cargador detiene la corriente, automáticamente,
si detecta que la batería se está sobrecalentando.
Revise la batería o reemplácela.
Si usted obtiene un código de la error, usted tiene que comprobar las conexiones, los niveles
de carga y/o substituir la batería.
19
Localización y resolución de problemas
PROBLEMA POSIBLE CAUSA SOLUCIÓN
Las pinzas de la batería no
hacen corto al juntarse una
con otra.
Este cargador está equipado
con un auto-recticador. Este
no permitirá paso de corriente
si las pinzas de la batería no
están conectadas en forma
correcta. Signicado, las
pinzas no harán corto si se
juntan una con otra.
No hay problema; es una
condición normal.
El cargador no se enciende
incluso al estar bien
conectado.
Tomacorriente de C.A. fuera
de funcionamiento.
Conexión eléctrica deciente.
Batería defectuosa.
Controle la posible presencia
de fusibles abiertos o
disyuntores que suministren
energía al tomacorriente de
CA.
Revise el cable de extensión
para cable y enchufe suelta.
Haga revisar la batería.
No puedo seleccionar los
6 o 12 Voltios.
El cargador está equipado
con detección automática de
voltaje, que automáticamente
detecta el voltaje y carga la
batería.
No hay problema; es una
condición normal.
La batería está conectada
correctamente, pero el LED
CHARGING no encendió
inmediatamente.
Si no se presiona el botón
Start / Stop, la carga deberá
comenzar en diez minutos.
No hay problema; es una
condición normal.
La batería está conectada
correctamente, pero el
LED CHARGING nunca
iluminado.
El voltaje de la batería es
bajo.
Pulse el botón de START /
STOP para comenzar a
cargar.
20
PROBLEMA POSIBLE CAUSA SOLUCIÓN
El LED BAD BATTERY se
ilumina.
El voltaje de la batería
todavía está debajo de 10V
(para una batería 12V) o de
5V (para una batería 6V)
después de 2 horas de carga.
(o)
En el modo de
mantenimiento, la corriente
de salida es de más de 1,5 A
durante 12 horas.
La batería no puede
desulfatada.
Se detecta la falta de progreso
y voltaje de la batería está por
debajo de 14,2V (para una
batería 12V) o de 7,1V (para
una batería 6V).
Voltaje inicial de la batería
está por debajo de 12,2V
(para una batería 12V) o de
6,1V (para una batería 6V) y
la entrada total es de menos
de 1,5 Ah.
El voltaje de la batería cae
por debajo de 12.2V (para
una batería 12V) o de 6,1V
(para una batería 6V) en el
modo de mantenimiento.
La batería puede estar
defectuosa. Asegúrese de
que no hay cargas en la
batería. Si hay eliminarlos. Si
no hay ninguno, verifíque o
reempláce la batería.
La batería puede estar
defectuosa. Verifíquela o
reemplácela.
La batería se puede
sobrecalienta. Si es así, deje
que la batería se enfríe. La
batería puede ser demasiado
grande o tener un circuito
en corto. Verifíquela o
reemplácela.
La capacidad de la batería es
demasiado bajo o la batería
es demasiado antigua.
Verifíquela o reemplácela.
La batería no mantiene la
carga. Puede ser causada
por una batería descargada
o la batería podría ser malo.
La batería puede estar
defectuosa. Asegúrese de que
no hay cargas en la batería.
Si hay eliminarlos. Si no hay
ninguno, verifíque o reempláce
la batería.
14. ANTES DE DEVOLVER A REPARACIONES
Si estas soluciones no eliminan el problema, o si desea obtener
más información sobre la solución de problemas, póngase en contacto
con el departamento de servicio al cliente para recibir asistencia:
www.batterychargers.com
o llame 1-800-621-5485
Para REPARACIÓN O DEVOLUCIÓN, comuníquese con Servicios al Cliente al
1-800-621-5485. NO ENVÍE LA UNIDAD hasta que usted reciba AUTORIZACIÓN
DE DEVOLUCIÓN DE MERCANCÍA (RMA) de Servicios al Cliente de Schumacher
Electric Corporation.
21
15. ESPECIFICACIONES
Voltaje de entrada ..........................................................................120V CA
@
60Hz, 3,6A
Salida de voltaje........................................ 6V o 12V, con detección automática de voltaje
Salida de corriente ................................................... 2A CC
@
6V CC; 15A CC
@
12V CC
16. GARANTÍA LIMITADA
GARANTIA LIMITADA NO VALIDA EN MEXICO.
SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,
MOUNT PROSPECT, IL 60056-2179, REALIZA LA PRESENTE GARANTÍA LIMITADA
AL COMPRADOR MINORISTA ORIGINAL DE ESTE PRODUCTO. LA PRESENTE
GARANTÍA LIMITADA NO PUEDE TRANSFERIRSE NI CEDERSE.
Schumacher Electric Corporation (el “Fabricante”) otorga garantía por este cargador de
batería por un plazo de dos (2) años contados a partir de la fecha de compra por menor
por la existencia de cualquier material o de mano de obra defectuosos que pudieran surgir
por su uso y cuidado normal. Si su unidad cuenta con material defectuoso o defectos de
mano de obra, la obligación de los Fabricantes, conforme a la presente garantía, será
simplemente reparar o sustituir el producto por uno nuevo o por una unidad reparada, a
elección del fabricante. Es obligación del comprador enviar la unidad con comprobante de
compra y los gastos de envío prepagos al fabricante o a sus representantes autorizados
para que ésta se pueda reparar o reemplazar.
El Fabricante no presta garantía por lo accesorios utilizados con este producto que no
sean los fabricados por Schumacher Electric Corporation y que no estén aprobados
para su uso con este producto. La presente Garantía Limitada será nula si el producto
se utiliza en forma errónea, se trata de manera inadecuada, es reparado o modicado
por personas que nos sean el Fabricante o si esta unidad es revendida a través de un
vendedor minorista no autorizado.
El Fabricante no realiza ninguna otra garantía, incluidas, a título enunciativo, las garantías
expresas, implícitas o legales, incluidas, a modo de ejemplo, las garantías implícitas
de comerciabilidad o adecuación a un n especíco. Asimismo, el Fabricante no será
responsable ante reclamos por daños accidentales, especiales ni directos en los que
incurran los compradores, usuarios u otras personas asociadas al producto, incluidas, a
título enunciativo, los ingresos y ganancias no percibidos, ventas anticipadas, oportunidades
comerciales, el buen nombre, la interrupción de la actividad comercial o cualquier otro
daño que haya provocado. Todas las garantías, excepto la garantía limitada incluida en el
presente, por medio de la presente, quedan expresamente anuladas y excluidas. Algunos
estados no permiten la exclusión ni la limitación de los daños accidentales ni directos
o el plazo de garantía implícita, por lo que las limitaciones o exclusiones mencionadas
anteriormente podrían no corresponder con su caso. La presente garantía le otorga
derechos legales especícos y es probable que usted cuente con otros derechos que
podrían diferir de los incluidos en la presente garantía.
LA PRESENTE GARANTÍA LIMITADA ES LA ÚNICA GARANTÍA LIMITADA EXPRESA
Y EL FABRICANTE NO ASUME NI AUTORIZA A NADIE A ASUMIR O A ADQUIRIR
NINGUNA OTRA OBLIGACIÓN RESPECTO DEL PRODUCTO QUE NO SEA LA
PRESENTE GARANTÍA.
Schumacher
®
y el logo Schumacher son marcas registradas
de Schumacher Electric Corporation.
23
¡AHORRE EN EL ENVÍO! ¡ACTIVE SU GARANTÍA EN LÍNEA-LA FORMA MAS RÁPIDA Y FÁCIL!
Visite nuestra página en www.batterychargers.com para registrar su producto en línea.
(¿No tiene acceso al internet? Llene la tarjeta de garantía y envíela.)
WARRANTY CARD / TARJETA DE GARANTÍA
SAVE ON POSTAGE! ACTIVATE YOUR WARRANTY ONLINE – THE QUICK AND EASY WAY!
Go to www.batterychargers.com to register your product online.
(No internet access? Send in the completed warranty card.)
TARJETA DE GARANTÍA
WARRANTY CARD
2 YEAR LIMITED
WARRANTY PROGRAM
REGISTRATION
MODEL: _____________________DESCRIPTION: ________________________
This is the only express limited warranty, and the manufacturer neither assumes
nor authorizes anyone to assume or make any other obligation. There is no other
warranty, other than what is described in the product owner’s manual.
The warranty card should be submitted within 30 days of purchase. The customer
must keep the ORIGINAL receipt because it will be required for any warranty claims.
This warranty is not transferable. Send warranty card only.
DO NOT SEND UNIT TO THIS ADDRESS FOR REPAIR.
Mail this card to: Schumacher Electric Corporation
801 Business Center Drive
Mount Prospect, IL 60056-2179
Name ______________________________________________________________
Street Address _______________________________________________________
City ________________________________State _________ Zip Code _________
Phone _____________________Email ___________________________________
Store Name Where Purchased ___________________ Date of Purchase _________
Store Location ____________________ UPC Number ________________________
Serial Number ______________________________________ (SEE PRODUCT)
For faster warranty activation, go to www.batterychargers.com to register your product online.
PROGRAMA DE REGISTRO
DE 2-AÑOS DE GARANTÍA
LIMITADA
MODELO: ____________________DESCRIPCIÓN: ________________________
Esta es la única garantía limitada expresa, y el productor no autoriza ni otorga
a alguien a realizar alguna otra obligación. No existe ninguna otra garantía
más que la descrita en el manual del dueño.
La tarjeta de garantía debe enviarse durante los primeros 30 días después de la
compra. El cliente debe mantener el recibo de compra ORIGINAL como
comprobante, el cual le otorga todo derecho a cualquier reclamo de garantía.
Esta garantía no es transferible. Envie tarjeta de garantía solamente.
NO ENVÍE LA UNIDAD A ESTA DIRECCIÓN PARA SU REPARACIÓN.
Enviar esta tarjeta a: Schumacher Electric Corporation
801 Business Center Drive
Mount Prospect, IL 60056-2179
Nombre ____________________________________________________________
Dirección ___________________________________________________________
Ciudad __________________________Estado ____________ C.P. _____________
Tel: ________________________ Correo electrónico _________________________
Nombre de la Tienda donde se Compró ____________ Fecha de compra _________
Localización de la Tienda ____________ Numero de Serie ____________________
Código de barras ___________________________ (CONSULTE EL PRODUCTO)
Para una activación más rápida, visite nuestra página de internet en www.batterychargers.com
1 / 1

Schumacher SC1280 15A Rapid Charger for Automotive and Marine Batteries El manual del propietario

Categoría
Cargadores de bateria
Tipo
El manual del propietario