Yamaha RX-V495 El manual del propietario

Marca: Yamaha

Modelo: RX-V495

Categoría: Receptor

Tipo: El manual del propietario

Printed in Malaysia ID

V342050

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

RX-V4 95

Natural Sound AV Receiver

Ampli-Tuner Audio-Video

OWNER’S MANUAL

MODE D’EMPLOI

U C A

01RX-V495-e/f cv1/4 6/22/99, 2:40 PM1

SAFETY INSTRUCTIONS

1 Read Instructions – All the safety and operating instructions

should be read before the unit is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and other instructions

should be followed.

5 Water and Moisture – The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming

pool, etc.

6 Carts and Stands – The unit should be used only with a

cart or stand that is recommended by the

manufacturer.

6A A unit and cart combination should be moved

with care. Quick stops, excessive force, and

uneven surfaces may cause the unit and cart

combination to overturn.

7 Wall or Ceiling Mounting – The unit should be mounted to a

wall or ceiling only as recommended by the manufacturer.

8 Ventilation – The unit should be situated so that its location

or position does not interfere with its proper ventilation. For

example, the unit should not be situated on a bed, sofa,

rug, or similar surface, that may block the ventilation

openings; or placed in a built-in installation, such as a

bookcase or cabinet that may impede the flow of air

through the ventilation openings.

9 Heat – The unit should be situated away from heat sources

such as radiators, stoves, or other appliances that produce

heat.

10 Power Sources – The unit should be connected to a power

supply only of the type described in the operating

instructions or as marked on the unit.

11 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the unit.

12 Cleaning – The unit should be cleaned only as

recommended by the manufacturer.

13 Nonuse Periods – The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry – Care should be taken so that

objects do not fall into and liquids are not spilled into the

inside of the unit.

15 Damage Requiring Service – The unit should be serviced

by qualified service personnel when:

A. The power-supply cord or the plug has been

damaged; or

B. Objects have fallen, or liquid has been spilled into the

unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or exhibits

a marked change in performance; or

E. The unit has been dropped, or the cabinet damaged.

16 Servicing – The user should not attempt to service the unit

beyond those means described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

17 Power Lines – An outdoor antenna should be located away

from power lines.

18 Grounding or Polarization – Precautions should be taken

so that the grounding or polarization is not defeated.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence

of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

01RX-V495-e/f-1 6/22/99, 1:32 PM2

English

19 For US customers only:

Outdoor Antenna Grounding – If an outside antenna is

connected to this unit, be sure the antenna system is

grounded so as to provide some protection against voltage

surges and built-up static charges. Article 810 of the

National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast

and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

FCC INFORMATION (for US customers only)

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound

come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfac-

tory results, please contact the local retailer authorized

to distribute this type of product. If you can not locate

the appropriate retailer, please contact Yamaha

Electronics Corp., U.S.A. 6660 Orangethorpe Ave,

Buena Park, CA 90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC,

to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation instruc-

tions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC Regula-

tions, Part 15 for Class “B” digital devices. Compliance

with these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

01RX-V495-e/f-1 6/22/99, 1:32 PM3

• Indoor FM Antenna

• Antenne FM intérieure

• AM Loop Antenna

• Cadre-antenne AM

• Antenna adapter

(U.S.A. and Canada models only)

• Adaptateur d’antenne

(Modèles pour les Etats-Unis et le

Canada seulement)

• Batteries (size AAA, R6, UM-4)

• Piles (taille AAA, R6, UM-4)

SUPPLIED ACCESSORIES

ACCESSOIRES FOURNIS

• After unpacking, check that the following parts are included.

• Après le déballage, vérifier que les pièces suivantes sont incluses.

• Remote control transmitter

• Télécommande

01RX-V495-e/f-1 6/22/99, 1:32 PM4

English

● 5-Channel Power Amplification

Minimum RMS Output Power

<0.04% THD, 20 Hz – 20 kHz>

Main: 60 W + 60 W (8 Ω)

Center:60 W (8 Ω)

Rear: 60 W + 60 W (8 Ω)

<0.07% THD, 1 kHz>

Main: 70 W + 70 W (8 Ω)

Center:70 W (8 Ω)

Rear: 70 W + 70 W (8 Ω)

● Digital Sound Field Processor

● Dolby Digital Decoder

● Dolby Pro Logic Surround Decoder

● CINEMA DSP: Theater-like Sound

Experience by the Combination of Dolby

Surround and YAMAHA DSP Technology

SUPPLIED ACCESSORIES........................................... 4

FEATURES .................................................................... 5

CAUTION ....................................................................... 6

●Introduction

FEATURES OF SOUND EFFECTS............................... 7

CONTROLS AND THEIR FUNCTIONS ......................... 9

●Preparation

SPEAKER SETUP ....................................................... 14

CONNECTIONS........................................................... 16

ADJUSTMENTS

BEFORE USING THIS UNIT .................................. 23

●Basic Operation

BASIC OPERATIONS .................................................. 28

TUNING OPERATIONS ............................................... 32

SETTING THE SLEEP TIMER.....................................37

●Information about DSP

USING THE DIGITAL SOUND FIELD

PROCESSOR (DSP) .............................................. 38

●Advanced Information

ADJUSTMENTS

IN THE “SET MENU” MODE...................................44

●Remote Control Transmitter

REMOTE CONTROL TRANSMITTER......................... 46

SETUP CODES ........................................................... 53

TROUBLESHOOTING ................................................. 54

SPECIFICATIONS ....................................................... 57

LIST OF MANUFACTURER’S CODES...................... 113

FEATURES

CONTENTS

● 6-Channel External Decoder Input for DTS

and other future formats

● Automatic Input Balance Control for

Dolby Pro Logic Surround

● Test Tone Generator for Easier Speaker

Balance Adjustment

● Speaker Output Mode Changing

Capability

● 40-Station Random Access Preset Tuning

● Automatic Preset Tuning

● Preset Station Shifting Capability

(Preset Editing)

● Video Signal Input/Output Capability

● SLEEP Timer

● Universal Remote Control

Transmitter with Preset Manufacturer

Codes

01RX-V495-e/f-1 6/22/99, 1:32 PM5

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2. Install this unit in a cool, dry, clean place – away from

windows, heat sources, sources of excessive vibration,

dust, moisture and cold. Avoid sources of humming

(transformers, motors). To prevent fire or electrical shock,

do not expose the unit to rain or water.

3. Never open the cabinet. If something drops into the set,

contact your dealer.

4. Do not use force on switches, controls or connection wires.

When moving the unit, first disconnect the power plug and

the wires connected to other equipment. Never pull the

wires themselves.

5. The openings on the unit cover assure proper ventilation of

the unit. If these openings are obstructed, the temperature

inside the unit will rise rapidly. Therefore, avoid placing

objects against these openings, and install the unit in a

well-ventilated area to prevent fire and damage.

Be sure to allow a space of at least 20 cm behind, 20 cm

on the both sides and 30 cm above the top panel of the unit

to prevent fire and damage.

6. The voltage used must be the same as that specified on

this unit. Using this unit with a higher voltage than

specified is dangerous and may result in fire or other

accidents. YAMAHA will not be held responsible for any

damage resulting from use of this unit with a voltage other

than specified.

7. Digital signals generated by this unit may interfere with

other equipment such as tuners, receivers or TVs. Move

this unit farther away from such equipment if interference is

observed.

8. Always set the VOLUME control to “

” before starting the

audio source play. Increase the volume gradually to an

appropriate level after playback has been started.

9. Do not attempt to clean the unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding that

the unit is faulty.

11. When not planning to use this unit for long periods of time

(ie., vacation, etc.), disconnect the AC power plug from the

wall outlet.

12. To prevent lightning damage, disconnect the AC power

plug and disconnect the antenna cable when there is an

electrical storm.

13. Grounding or polarization – Precautions should be taken so

that the grounding or polarization of an appliance is not

defeated.

14. AC outlet

Do not connect audio equipment to the AC outlet on the

rear panel if that equipment requires more power than the

outlet is rated to provide.

15. Voltage Selector (China and General Models only)

The voltage selector on the rear panel of this unit must

be set for your local main voltage BEFORE plugging

into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off. This state is called the standby mode. In

this state, this unit is designed to consume a very small

quantity of power.

FREQUENCY STEP switch

(China and General Models only)

Because the interstation frequency spacing differs in

different areas, set the FREQUENCY STEP switch (located

at the rear) according to the frequency spacing in your area.

Before setting this switch, disconnect the AC power plug of

this unit from the AC outlet.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide

slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

01RX-V495-e/f-1 6/22/99, 1:32 PM6

English

FEATURES OF SOUND EFFECTS

Welcome to the exciting world of digital home entertainment.

This unit is one of the most complete and advanced AV

receivers available. Some of the more advanced features may

not be familiar to you, but they are easy to use. State-of-the-art

technologies such as Dolby Digital and Digital Theater Systems

(DTS) may be new to your home, but you have probably

experienced the amazing realism they bring to feature films in

theaters around the world.

To make the listening experience even more enjoyable, this unit

includes a number of exclusive, digitally created listening

environments known as digital sound fields. Choosing a sound

field program is like transporting yourself to such venues as an

outdoor arena, a European church, or a cozy jazz club. Take

some time now to read more about these features and enjoy

the new experiences this unit brings to your home theater.

Digital Sound Field Processing

What is it that makes live music so good? Today’s advanced

sound reproduction technology lets you get extremely close to

the sound of a live performance, but the chances are that you’ll

still notice something missing — the acoustic environment of

the live concert hall. Extensive research into the exact nature

of the sonic reflections that create the ambience of a large hall

has made it possible for YAMAHA engineers to bring you this

same sound to your listening room, so you’ll feel all the sound

of a live concert.

Furthermore, our technicians, armed with sophisticated

measuring equipment, have even made it possible to capture

the acoustics of a variety of actual concert halls, theaters, etc.

from around the world, to allow you to accurately re-create any

one of these live performance environments, all in your own

home.

Dolby Pro Logic Surround

Dolby Pro Logic Surround has been used in movie theaters

since the mid-seventies. It has also been available in home

entertainment systems since the late eighties and continues to

be a popular format for home theater systems. It uses four

discrete channels and five speakers to reproduce realistic and

dynamic sound effects: two main channels (left and right), a

center channel for dialog, and a rear channel for special sound

effects. The rear channel reproduces sound within a narrow

frequency range.

Most video tapes and laser discs include Dolby Pro Logic

Surround encoding, as do many TV and cable broadcasts. The

Dolby Pro Logic Surround decoder built into this unit employs a

digital signal processing system that stabilizes each channel for

even more accurate sound positioning than is available with

standard analog processors.

Dolby Digital

The built-in Dolby Digital decoder leads you into a totally new

sound experience.

Dolby Digital is a new generation of multi-channel digital audio

technology, or the newest spatial sound processing format

developed for 35 mm-film movies by employing a new kind of

low bit-rate audio coding.

Dolby Digital is a digital surround sound system that provides

completely independent multi-channel audio to listeners. In

multi-channel form, Dolby Digital provides 5 full-range channels

in what is sometimes referred to as a “3/2” configuration: three

front channels (left, center and right), plus two surround

channels. A sixth bass-only effect channel is also provided for

output of LFE (low frequency effect), or low bass effects that

are independent of other channels. This channel is counted as

0.1, thus giving rise to the term 5.1 channels in total.

Compared to Dolby Pro Logic, which is referred to a “3/1”

system (left front, center, right front and just one surround

channel), Dolby Digital features two surround channels, called

stereo or split surrounds, each offering the same full-range

fidelity as the three front channels.

Sound of wide dynamic range reproduced by the 5 full-range

channels provides listeners with excitement that has never

been experienced before. Precise sound orientation by

discrete digital sound processing expands the realism that the

original movie possesses.

LD and DVD are home audio/video program source that could

benefit from Dolby Digital. In the near future, Dolby Digital will

also be applied to DBS, CATV and HDTV. The ongoing release

of Dolby Stereo Digital theatrical films now underway will

provide an immediate source of Dolby Digital encoded video

software.

Introduction

01RX-V495-e/f-1 6/22/99, 1:32 PM7

Manufactured under license from Dolby Laboratories Licensing

Corporation. “DOLBY”, “PRO LOGIC”, and the double-D symbol

are trademarks of Dolby Laboratories Licensing Corporation.

The following original functions make the surround-sound effect

of Dolby Digital become the most suitable for your audio

system and the listening conditions.

CINEMA DSP: Dolby Surround + DSP

The Dolby Surround sound system shows its full ability in a

large movie theater, because movie sounds are originally

designed to be reproduced in a large movie theater using many

speakers. It is difficult to create a sound environment similar to

that of a movie theater in your listening room, because the

room size, materials of inside walls, the number of speakers,

etc. of your listening room are very different from those of a

movie theater.

YAMAHA DSP technology made it possible to present you with

nearly the same sound experience as that of a large movie

theater in your listening room by compensating for the lack of

presence and dynamics in your listening room with its original

digital sound fields combined with the Dolby Surround sound

system.

CINEMA DSP

The YAMAHA “CINEMA DSP” logo indicates those programs

that are created by the combination of Dolby Surround and

YAMAHA DSP technology.

Dolby Pro Logic + 2 Digital Sound Fields

Digital sound fields are created on the presence side and the

rear surround side of the Dolby Pro Logic Surround-decoded

sound field, respectively. They create a wide acoustic

environment and emphasize the surround effect in the room,

letting you feel as much presence as if you are watching a

movie in a popular Dolby Stereo theater.

This combination is available when the DOLBY PRO LOGIC

ENHANCED/DOLBY DIGITAL ENHANCED, 70 mm MOVIE

THEATER/DIGITAL MOVIE THEATER or TV SPORTS sound

field program is selected, and the input signal of source is

analog, PCM audio or encoded with Dolby Digital sound in

2-channel.

Dolby Digital + 3 Digital Sound Fields

Digital sound fields are created on the presence side and the

independent left and right surround sides of the Dolby Digital-

decoded sound field, respectively. They create a wide

acoustic environment and strong surround effect in the room

without losing high-channel separation. With the wide

dynamic range of Dolby Digital sound, this sound field

combination lets you feel as if you are watching a movie in the

newest Dolby Stereo Digital theater. This will be the most

ideal home theater sound at the present time.

This combination is available when the DOLBY PRO LOGIC

ENHANCED/DOLBY DIGITAL ENHANCED, 70 mm MOVIE

THEATER/DIGITAL MOVIE THEATER or TV SPORTS sound

field program is selected, and the input signal of source is

encoded with Dolby Digital sound (except in 2-channel).

01RX-V495-e/f-1 6/22/99, 1:32 PM8

English

CONTROLS AND THEIR FUNCTIONS

FRONT PANEL

1 STANDBY/ON

Press this switch to turn on the power to this unit. Press it

again to set this unit to the standby mode.

Standby mode

In this state, this unit consumes a very small quantity of

power to receive infrared-signals from the remote control

transmitter.

2 Remote control sensor

This receives signals from the remote control transmitter.

3 Display

This shows various information. (Refer to page 11 for details.)

4 MEMORY (MAN’L/AUTO FM)

Press this button to store the broadcasting stations.

When this button is pressed and held for more than three

seconds, the automatic preset tuning begins.

5 EDIT

This button is used to exchange the assignment of two preset

stations with each other.

6 TUNING MODE (AUTO/MAN’L MONO)

Press this button to switch the tuning mode to automatic or

manual. To select the automatic tuning mode, press this button

so that the “AUTO TUNING” indicator lights up on the display.

To select the manual tuning mode, press this button so that the

“AUTO TUNING” indicator goes off.

7 FM/AM

Press this button to switch the reception band to FM or AM.

8 TUNING UP/DOWN

This button is used for tuning. Press the UP side to tune in to

higher frequencies, and press the DOWN side to tune in to

lower frequencies.

9 TAPE/MD MON / EXT. DECODER

Press this button to play a tape or an MD. The “TAPE/MD

MON” indicator lights up on the display.

When you press the button next, the “TAPE/MD MON” indicator

goes off, “EXT. DECDR” appears on the display and you can

play the signal connected to the EXTERNAL DECODER

INPUT terminals.

0 INPUT

Turn this selector to select the program source (VCR, VIDEO

AUX, TV/DBS, DVD/LD, CD, TUNER, PHONO) to listen to or

watch.

The name of the selected program source appears on the

display.

01RX-V495-e/f-1 6/22/99, 1:32 PM9

q INPUT MODE

This button switches the DVD/LD and TV/DBS input signal

mode (AUTO/ANALOG).

w VOLUME

This control is used to raise or lower the volume level.

e PHONES jack

When you use headphones, connect the headphones to the

PHONES jack. You can listen to the sound to be output from

the main speakers through the headphones.

When using headphones only, set both SPEAKERS A and B to

the OFF position and switch off the digital sound field processor

(so that no DSP program name appears on the display) by

pressing EFFECT.

r SPEAKERS

Set A or B (or both A and B) to the ON position for the main

speaker system (connected to this unit) that you want to use.

Set the button(s) for the main speaker system you don’t want to

use to the OFF position.

t A/B/C/D/E

Press this button to select one of a group (A to E) of preset

stations.

y Preset station number selector

Each of these buttons selects a preset station number

(1 to 8).

u Tone controls

These controls are only effective for the sound from the main

speakers.

BASS

Use this control to increase or decrease the low-frequency

response. The “0” position produces flat response.

TREBLE

Use this control to increase or decrease the high-frequency

response. The “0” position produces flat response.

i BALANCE

This control is only effective for the sound from the main

speakers.

Turn the control to adjust the balance of the output volume to

the left and right speakers to compensate for sound imbalance

caused by the speaker location or listening room conditions.

o TIME/LEVEL

Press this button to select the item in the TIME/LEVEL mode.

p +/–

These buttons are used to adjust the settings of the SET MENU

mode and the TIME/LEVEL mode. In the TIME/LEVEL mode,

press + to increase the delay time or speaker output level.

Press – to decrease the delay time or speaker output level.

a SET MENU

Press this button to select functions in the SET MENU mode.

s PROGRAM selector

Press

or to select the DSP program.

The name of the selected program appears on the display.

d EFFECT

This button switches on and off the output from the center and

rear speakers so that the sound becomes the normal

2-channel.

* Even if the output from the center and rear speakers is off,

when the Dolby Digital is decoded, the signals on all

channels are distributed to the main channels and output

from the main speakers.

f VIDEO AUX terminals

Connect an auxiliary video or audio input source unit such as a

camcorder to these terminals. The source connected to these

terminals can be selected by INPUT.

01RX-V495-e/f-1 6/22/99, 1:32 PM10

English

1 Multi-information display

This displays various information, for example the station

frequency, preset station number and name of the selected

program source.

2 MEMORY indicator

When MEMORY is pressed, this indicator flashes for about five

seconds. During this period, the displayed station can be

stored in the memory.

3 AUTO TUNING indicator

This lights up when the unit is in the automatic tuning mode.

4 TAPE/MD MON indicator

This lights up when the tape deck (or MD recorder, etc.) is

selected as the program source by pressing TAPE/MD MON /

EXT. DECODER on the front panel or TAPE/MD on the remote

control transmitter.

5 STEREO indicator

This lights up when an FM stereo broadcast with sufficient

signal strength is being received.

DISPLAY PANEL

Signal-level meter

This indicates the signal level of the station being received.

If multipath interference is detected, the indication decreases.

7 , and indicators

“

” lights up when the built-in Dolby Digital decoder is

on and the signal of the selected source encoded in Dolby

Digital sound is not in 2-channel. “

” lights up when the

built-in digital sound field processor is on, and “

”

lights up when the built-in Dolby Pro Logic Surround decoder is

on. Depending on the selected DSP program, both “

”

and “

”, or both “ ” and “ ” will light up.

8 SLEEP indicator

This lights up while the built-in SLEEP timer is functioning.

01RX-V495-e/f-1 6/22/99, 1:32 PM11

REMOTE CONTROL TRANSMITTER

See “REMOTE CONTROL TRANSMITTER” on page 46 for full details.

1 Component selector

Press the button for the component you want to control with the

remote control transmitter. (The proper code must be set for

your component. See “SETUP CODES” on page 53.)

When the component selector has been pressed, the remote

control transmitter is set to operate that component.

2 POWER

When you have preset the code for a YAMAHA component, this

button switches between the power on and standby mode.

When you have preset the code for another manufacturer’s

component, this button turns on that component if it has a

remote control transmitter with a power button.

* It only functions when AMP<TUNER>, TAPE/MD, CD, DVD/LD or

DVD MENU on the component selector has been pressed.

3 TEST

Press this button to output the test tone for each speaker.

* It only functions when AMP<TUNER> on the component selector

has been pressed.

4 A/B/C/D/E, PRESET +/–

These buttons are used to select a preset station.

* They only function when AMP<TUNER> on the component selector

has been pressed.

5 MUTE

Press this button to mute the sound.

6 VOLUME

These buttons are used to adjust the volume.

: Turns up the volume.

: Turns down the volume.

7 SLEEP

This button is used to set the SLEEP timer.

8 PRG+, PRG–

These buttons are used to select a DSP program.

* They only function when AMP<TUNER> on the component selector

has been pressed.

9 Indicator

This flashes in red when a button on the remote control

transmitter is pressed. When it flashes rapidly several times,

press the selected button again.

0 Input selector (1 to 9)

/Numeric buttons

1) These buttons are used to select the program source to be

played.

* They only function when AMP<TUNER>, TAPE/MD, CD or

DVD/LD on the component selector has been pressed.

2) These buttons are used to select the menu or channel.

* They only function when DVD MENU, VCR, CBL/DBS or TV on

the component selector has been pressed.

01RX-V495-e/f-1 6/22/99, 1:32 PM12

English

q EFFECT

/CLEAR

/+100

1) This button is used to switch the DSP program on or off.

* It only functions when AMP<TUNER>, TAPE/MD, CD, DVD/LD,

VCR or TV on the component selector has been pressed.

2) This button is used to clear the settings.

* It only functions when DVD MENU on the component selector

has been pressed.

3) This button is used to select the channel.

* It only functions when CBL/DBS on the component selector has

been pressed.

w ENTER

/+10

1) This button is used to enter the channel.

* It only functions when VCR, CBL/DBS or TV on the component

selector has been pressed.

2) This button is used to select the menu.

* It only functions when DVD MENU on the component selector

has been pressed.

e DISC SKIP +/–

/CH +/–

1) These buttons are used to skip to the next or previous disc.

* They only function when CD, DVD/LD or DVD MENU on the

component selector has been pressed.

2) These buttons are used to select the next or previous

channel.

* They only function when VCR, CBL/DBS or TV on the

component selector has been pressed.

r Operation buttons

/Setup buttons

1) These buttons function as play, stop, skip, etc. for

operating the component.

* They only function when TAPE/MD, CD, DVD/LD, VCR or TV on

the component selector has been pressed.

2) These buttons are for adjusting various settings.

* They only function when AMP<TUNER>, DVD MENU or CBL/

DBS on the component selector has been pressed.

01RX-V495-e/f-1 6/22/99, 1:32 PM13

SPEAKER SETUP

This unit is designed to provide the best sound-field quality with

a 5-speaker configuration, using main speakers, rear speakers

and a center speaker.

The main speakers are used for the main source sound plus

the effect sounds. They will probably be the speakers from

your present stereo system. The rear speakers are used for

the effect and surround sounds, and the center speaker is for

the center sounds (dialog, vocals, etc.). If for some reason it is

not practical to use a center speaker, you can do without it.

Best results, however, are obtained with the full system.

The main speakers should be high-performance models and

have enough power-handling capacity to accept the maximum

output of your audio system.

The other speakers do not have to be equal to the main

speakers. For precise sound localization, however, it is ideal to

use high-performance models that can reproduce sounds over

the full-range for the center speaker and the rear speakers.

5-Speaker Configuration

This configuration is the most effective and recommended one.

When playing back a source using the DSP program,

DOLBY PRO LOGIC/DOLBY DIGITAL, DOLBY PRO LOGIC

ENHANCED/DOLBY DIGITAL ENHANCED, 70 mm MOVIE

THEATER/DIGITAL MOVIE THEATER, MONO MOVIE or TV

SPORTS, or when playing back a source which contains

center-channel signals (dialog, vocals, etc.) using any DSP

program that is Dolby Digital-decoded, conversations will be

output from the center speaker and the ambience will be

excellent.

Note: Set the CNTR (CENTER SPEAKER) mode to the

“LARGE” or “SMALL” position. (See page 23 for

details.)

SPEAKER CONFIGURATION

Use of a subwoofer expands your sound field

It is also possible to further expand your system with the

addition of a subwoofer and amplifier. The use of a subwoofer

is effective not only for reinforcing bass frequencies from any or

all channels, but also for reproducing the LFE (low frequency

effect) sound with high fidelity when playing back a source that

is Dolby Digital-decoded. You may wish to choose the

convenience of a YAMAHA Active Servo Processing Subwoofer

System, which has its own built-in power amplifier.

4-Speaker Configuration

The center speaker is not used in this configuration. When

playing back a source using the DSP program, DOLBY PRO

LOGIC/DOLBY DIGITAL, DOLBY PRO LOGIC ENHANCED/

DOLBY DIGITAL ENHANCED, 70 mm MOVIE THEATER/

DIGITAL MOVIE THEATER, MONO MOVIE or TV SPORTS, or

when playing back a source which contains center-channel

signals (dialog, vocals, etc.) using any DSP program that is

Dolby Digital-decoded, the center sound is output from the left

and the right main speakers. However, the sound effect of

other programs will be the same as that of the 5-speaker

configuration.

Note: Be sure to set the CNTR (CENTER SPEAKER) mode to

the “NONE” position. (See page 23 for details.)

SPEAKERS TO BE USED

Main L Main R

Rear L Rear R

Dialog

Surround sound

Main L Center Main R

Rear L Rear R

Dialog

Surround sound

01RX-V495-e/f-2 6/22/99, 1:32 PM14

English

SPEAKER PLACEMENT

Refer to the following diagram when you place the speakers.

Main: The position of your present stereo speaker

system.

Rear: Behind your listening position, facing slightly

inward. Nearly 1.8 m (approx. 6 feet) up from the

floor.

Center: Precisely between the main speakers. (To avoid

interference with TV sets, use a magnetically

shielded speaker.)

Subwoofer: The position of the subwoofer is not as critical,

because low bass tones are not highly directional.

Rear

speaker (R)

Main

speaker (R)

Center speaker

Subwoofer

Main

speaker (L)

Rear

speaker

(L)

01RX-V495-e/f-2 6/22/99, 1:32 PM15

SWITCHED AC OUTLET(S)

U.S.A., Canada, Singapore, China and General models

........................................................... 2 SWITCHED OUTLETS

Australia model .....................................1 SWITCHED OUTLET

Use these to connect the power cords from your components to

this unit.

The power to the SWITCHED AC OUTLET(S) is controlled by

this unit’s STANDBY/ON or the provided remote control

transmitter’s POWER. These outlets will supply power to any

component whenever this unit is turned on.

The maximum power (total power consumption of components)

that can be connected to the SWITCHED AC OUTLET(S) is

100 watts.

CONNECTIONS

Never plug in this unit and other components until all connections have been completed.

CONNECTIONS WITH OTHER COMPONENTS

When making connections between this unit and other components, be sure all connections are made correctly, that is to say L

(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.

* If you have YAMAHA components numbered as !, #, $, etc. on the rear panel, connections can be made easily by making sure

to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.

Turntable Monitor TV

DVD player,

LD player, etc.

CD player Tape deck,

MD recorder, etc.

TV/DBS tuner

VCR

(Video cassette recorder)

To AC outlet

(U.S.A. model)

GND terminal (for turntable use)

Connecting the ground (earth) wire of the turntable to the GND terminal will normally minimize hum, but in some cases, better

results may be obtained with the ground wire disconnected.

01RX-V495-e/f-2 6/22/99, 1:32 PM16

English

CONNECTING TO AN EXTERNAL DECODER

When using the DTS or other decoder with 6-channel discrete outputs, connect the 6CH DISCRETE OUTPUT terminals of the

decoder to the EXTERNAL DECODER INPUT terminals of this unit.

DTS or other decoder with 6-channel

discrete outputs

DVD player, LD player or other

unit with digital outputs

(U.S.A. model)

Camcorder

CONNECTING TO VIDEO AUX TERMINALS (ON THE FRONT PANEL)

These terminals are used to connect any video input source, such as a camcorder, to this unit.

VIDEO AUX

01RX-V495-e/f-2 6/22/99, 1:32 PM17

CONNECTING TO DIGITAL (COAXIAL AND/OR OPTICAL) TERMINALS

If your DVD (LD) player, TV/DBS tuner, etc. are equipped with

coaxial or optical digital audio signal output terminals, they can

be connected to this unit’s COAXIAL and/or OPTICAL digital

signal input terminals.

To make a connection between optical digital audio signal

terminals, remove the cover from each terminal, and then

connect them by using a commercially available optical fiber

cable that conforms to EIAJ standards. Other cables might not

function correctly.

Even if you connect an audio/video unit to the COAXIAL (or

OPTICAL) terminal of this unit, you must keep the unit

connected with the same named analog audio signal terminals

of this unit, because a digital signal cannot be recorded by a

tape deck, MD recorder or VCR connected to this unit. You can

easily switch the selection of input signals between “digital” and

“analog”. (See page 30 for details.)

Notes

• When connecting an audio/video unit to both the digital and

analog terminals of this unit, make sure to connect between

terminals of the same name.

• Be sure to attach the covers when the OPTICAL terminals

are not being used in order to protect them from dust.

• The input signal from the DVD/LD input terminals is selected

in the following order of priority with the input mode set to the

AUTO position:

1 COAXIAL terminal

2 OPTICAL terminal

3 Analog terminal

• All digital audio signal input terminals are applicable to

sampling frequencies of 32 kHz, 44.1 kHz and 48 kHz.

• If your LD player has Dolby Digital RF signal output terminal

and not digital signal output, use the RF demodulator

(separate purchase).

DVD or LD player TV/DBS tuner

(U.S.A. model)

01RX-V495-e/f-2 6/22/99, 1:32 PM18

English

Note

Use speakers with the specified impedance shown on the

rear panel of this unit.

Main speaker connections

One or two speaker systems can be connected to this unit. If

you use only one speaker system, connect it to either of the

SPEAKERS A or B terminals.

Rear speaker connections

A rear speaker system can be connected to this unit. Place

them to the rear of your listening position.

Center speaker connection

A center speaker can be connected to this unit. Place it on or

under the TV.

Subwoofer connection

You may wish to add a subwoofer to reinforce low frequencies

or to output low bass sound from the subwoofer channel.

If you have a subwoofer with built-in amplifier, including the

YAMAHA Active Servo Processing Subwoofer System, connect

the SUBWOOFER OUTPUT terminal of this unit to the input

terminal of the subwoofer system.

If you have a separate amplifier and subwoofer, connect the

SUBWOOFER OUTPUT terminal of this unit to the input

terminal of the subwoofer amplifier, and then connect the

speaker terminals of the subwoofer amplifier to the subwoofer.

When the input signals to this unit are for normal 2-channel

stereo, this terminal outputs only frequencies below 90 Hz from

the main and center channels. When discrete signals are input

to this unit and are selected as the input source, this terminal

outputs signals from the subwoofer channel.

Note: The output level of signals from this terminal is adjusted

by VOLUME on the front panel or VOLUME (

) on

the remote control transmitter.

CONNECTING SPEAKERS

Rear speakers

Subwoofer system

Center speaker

Right

Left

Main speakers A Main speakers B

Right

Left

Right Left

REAR

(SURROUND)

CENTER

MAIN

SUB

WOOFER

OUTPUT

SPEAKERS

01RX-V495-e/f-2 6/22/99, 1:32 PM19

How to connect

Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are

faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and –

markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.

Caution

Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could

damage the unit and/or speakers.

Connecting to the MAIN SPEAKERS terminals

Red: positive (+)

Black: negative (–)

1 Unscrew the knob.

2 Remove approx. 5 mm

(1/4”) of insulation from

each of the speaker

wires and insert the bare

wire into the terminal.

3 Tighten the knob to

secure the wire.

1 Press the tab.

2 Remove approx. 5 mm

(1/4”) of insulation from

each of the speaker

wires and insert the bare

wire into the terminal.

3 Release the tab to

secure the wire.

Connecting to the REAR and CENTER

SPEAKERS terminals

Red: positive (+)

Black: negative (–)

Banana plug connections are also possible (except for the

Singapore model). Simply insert the banana plug connector

into the corresponding terminal.

01RX-V495-e/f-2 6/22/99, 1:32 PM20

English

IMPEDANCE SELECTOR SWITCH

Select the position whose requirements your speaker system

meets.

(Upper position)

Main: If you use one pair of main speakers, the impedance of

each speaker must be 4 Ω or higher.

If you use two pairs of main speakers, the impedance

of each speaker must be 8 Ω or higher.

Center: The impedance of the speaker must be 6 Ω or higher.

Rear: The impedance of each speaker must be 6 Ω or

higher.

(Lower position)

Main: If you use one pair of main speakers, the impedance of

each speaker must be 8 Ω or higher.

If you use two pairs of main speakers, the impedance

of each speaker must be 16 Ω or higher.

The impedance of each speaker must be 8 Ω or

higher.

Center: The impedance of the speaker must be 8 Ω or higher.

Rear: The impedance of each speaker must be 8 Ω or

higher.

WARNING

Do not change the IMPEDANCE SELECTOR switch setting

while the power to this unit is on, otherwise this unit may be

damaged.

If this unit fails to turn on when the STANDBY/ON switch is

pressed, the IMPEDANCE SELECTOR switch may not be

fully set to either end. If so, set the switch to either end fully

when this unit is in the standby mode.

IMPEDANCE SELECTOR

(U.S.A. model)

01RX-V495-e/f-2 6/22/99, 1:32 PM21

Connecting the AM loop antenna

* The AM loop antenna should be placed away from this unit. The antenna may be hung on a wall.

* The AM loop antenna always should be connected, even if an outdoor AM antenna is connected to this unit.

ANTENNA CONNECTIONS

Each antenna should be correctly connected to the designated terminals, referring to the following diagram.

Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal

strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor

reception quality, an outdoor antenna may result in improvement.

GND TERMINAL

For maximum safety and minimum interference, connect the

GND terminal to a good earth ground. A good earth ground is a

metal stake driven into moist earth.

Notes

• When connecting the indoor FM

antenna, firmly insert its connector

into the FM ANT terminal.

• If you need an outdoor FM antenna to

improve FM reception quality, either

300-ohm feeder or coaxial

cable may be used. In locations

troubled by electrical interference, coaxial cable is preferable.

Orient so that the best

reception is obtained.

12 3

Outdoor FM antenna

75-ohm/300-ohm

antenna adapter

75-ohm coaxial cable

75-ohm/300-ohm

antenna adapter

300-ohm feeder

Ground

AM loop

antenna

(included)

Outdoor AM antenna

Indoor FM

antenna

(included)

(U.S.A. model)

01RX-V495-e/f-2 6/22/99, 1:32 PM22

English

ADJUSTMENTS BEFORE USING THIS UNIT

SELECTING THE OUTPUT MODES

This unit provides you the following five functions to determine the method of distributing output signals to speakers suitable for

your audio system. When speaker connections have all been completed, select the proper setting for each function to make the

best use of your speaker system. (See “ADJUSTMENTS IN THE ‘SET MENU’ MODE” on page 44.)

1. CNTR (CENTER SPEAKER) 2. REAR (REAR SPEAKERS) 3. MAIN (MAIN SPEAKERS)

4. BASS (LFE/BASS OUT) 5. M.LVL (MAIN LEVEL)

DESCRIPTION OF EACH FUNCTION

CNTR (CENTER SPEAKER)

Choices: LARGE/SMALL/NONE

Preset position: LARGE

LARGE: Select this position when your center speaker is

approximately the same size as the main speakers.

SMALL: Select this position when you use a center speaker

that is smaller than the main speakers.

In this position, low bass signals (below 90 Hz) on the

center channel are output from the main speakers (or

the SUBWOOFER OUTPUT terminal if the SMALL

position is selected for “MAIN” and the SW position is

selected for “BASS”).

NONE: Select this position when you do not have a center

speaker. The center channel sound will be output

from the left and right main speakers.

REAR (REAR SPEAKERS)

Choices: LARGE/SMALL

Preset position: LARGE

LARGE: Select this position if your rear speakers have high

ability for bass reproduction, or a subwoofer is

connected to the rear speaker in parallel.

In this position, full-range signals are output from the

rear speakers.

SMALL: Select this position if your rear speakers do not have

high ability for bass reproduction.

In this position, low bass signals (below 90 Hz) on

the rear channels are output from the SUBWOOFER

OUTPUT terminal (or the main speakers if the MAIN

position is selected for “BASS”).

MAIN (MAIN SPEAKERS)

Choices: LARGE/SMALL

Preset position: LARGE

LARGE: Select this position if your main speakers have high

ability for bass reproduction.

In this position, full-range signals present on the

main channels are output from the main speakers.

SMALL: Select this position if your main speakers do not

have high ability for bass reproduction. However, if

your system does not include a subwoofer, do not

select this position.

In this position, low bass signals (below 90 Hz) on

the main channels are output from the

SUBWOOFER OUTPUT terminal if the SW or BOTH

position is selected for “BASS”.

BASS (LFE/BASS OUT)

Choices: SW/MAIN/BOTH

Preset position: SW

MAIN: Select this position if your system does not include a

subwoofer.

In this position, full-range signals present on the

main channels, signals from the LFE channel and

other low bass signals that are selected for “CNTR”

to “MAIN” to be distributed from other channels are

output from the main speakers.

SW/BOTH:

Select either the SW or BOTH position if your

system includes a subwoofer.

In either position, signals on the LFE channel and

other low bass signals that are selected for “CNTR”

to “MAIN” to be distributed from other channels are

output from the SUBWOOFER OUTPUT terminal.

When the LARGE position is selected for “MAIN”, in

the SW position, no signal is distributed from the

main channels to the SUBWOOFER OUTPUT

terminal; however, in the BOTH position, low bass

signals from the main channels are output to both

the main speakers and the SUBWOOFER OUTPUT

terminal.

M.LVL (MAIN LEVEL)

Choices: NRML (NORMAL)/–10 dB

Preset position: NRML (NORMAL)

NRML (NORMAL):

Normally select this position.

–10 dB: Select this position if the sound output from the main

speakers is too loud and cannot be balanced with

the sound output from the center and rear speakers.

In this position, the sound output from the main

speakers is attenuated.

01RX-V495-e/f-2 6/22/99, 1:32 PM23

1 2

ADJUSTING METHOD

Adjustments should be made while watching the information on this unit’s display.

When adjusting with the remote control transmitter, press

AMP<TUNER> on the component selector on the remote

control transmitter.

1 Turn the power on.

Front panel Remote control

2 Press SET MENU once or more to select the function

“CNTR” on the display.

Front panel Remote control

3 Press + or – once or more to select the setting you

want.

Front panel Remote control

4 Repeat steps 2 and 3 to change the setting for

“REAR”, “MAIN”, “BASS” and/or “M.LVL” in the same

way.

01RX-V495-e/f-2 6/22/99, 1:32 PM24

English

2 1

4,74

SPEAKER BALANCE ADJUSTMENT

This procedure lets you adjust the sound output level balance between the main, center and rear speakers by using the built-in test

tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from

each speaker. This is important for the best performance of the digital sound field processor, the Dolby Digital decoder and the

Dolby Pro Logic Surround decoder.

The adjustment of each speaker output level should be done at your listening position with the remote control transmitter.

After completing the adjustment of the output level for each speaker, use VOLUME (

) on the remote control

transmitter at your listening position to check if the adjustments are satisfactory.

Press AMP<TUNER> on the component selector on the

remote control transmitter.

1 Set VOLUME to the “ ” position.

Front panel

2 Turn the power on.

Front panel Remote control

3 Select the main speakers to be used.

Front panel

* If you use two main speaker systems, press both A and B.

5,9

01RX-V495-e/f-2 6/22/99, 1:33 PM25

6 Turn up the volume.

Remote control

You will hear a test tone (like pink noise) from each

speaker for about two seconds in following order: left main

speaker, center speaker, right main speaker, right rear

speaker and left rear speaker. The display changes as

shown below.

* If the function “CNTR” in the SET MENU mode is set to

the NONE position, you will hear the center channel test

tone from the left and right main speakers.

7 Adjust BALANCE so that the sound output level of the

left main speaker and the right main speaker is the

same.

Front panel

Main (L)

Center

Main (R)

Rear (R)

Rear (L)

4 Set BASS, TREBLE and BALANCE to the “0” position.

Front panel

5 Press TEST so that “TEST LEFT” appears on the

display.

Remote control

01RX-V495-e/f-2 6/22/99, 1:33 PM26

English

8 Adjust the sound output levels of the center speaker

and the rear speakers so that they become almost the

same as that of the main speakers.

Press TIME/LEVEL once or more to select the speaker

to be adjusted so that “CENTER”, “R SUR.”, “L SUR.”

or “SWFR” appears on the display.

Remote control

* You cannot adjust the delay time while the test tone is

sounding even if “DELAY” appears on the display

after pressing TIME/LEVEL once or more.

Adjust the level.

* Pressing + raises and – lowers the level.

* While adjusting, the test tone is fixed on the selected

speaker.

Remote control

9 Press TEST again to stop the test tone.

Remote control

Notes

• Once you have completed these adjustments, you can only

adjust the overall sound level of your audio system by using

VOLUME (or VOLUME (

) on the remote control

transmitter).

• If you use external power amplifiers, you may also use their

volume controls to achieve the proper balance.

• If the function “CNTR” in the SET MENU mode is set to the

NONE position, the sound output level of the center speaker

cannot be adjusted in step 8. The center sound is

automatically output from the left and right main speakers.

• If there is insufficient sound output from the center and rear

speakers, you may decrease the main speaker output level

by setting “M.LVL” to “–10 dB”.

01RX-V495-e/f-2 6/22/99, 1:33 PM27

3,4

BASIC OPERATIONS

TO PLAY A SOURCE

3 Select the desired program source by using INPUT.

(Turn on the TV/monitor for video sources.)

Front panel Remote control

The name of the selected program source will appear on

the display.

To play a tape or an MD

Press TAPE/MD MON / EXT. DECODER

on the front panel or TAPE/MD on the

remote control transmitter so that the

“TAPE/MD MON” indicator lights up on

the display.

To use a decoder connected to the EXTERNAL

DECODER INPUT terminals

Press TAPE/MD MON / EXT. DECODER once or more on

the front panel or EXT. DEC. on the remote control

transmitter so that “EXT. DECDR” appears on the display.

When using the remote control transmitter

• Press AMP<TUNER> on the component selector.

• When controlling an audio/visual component (tape deck,

MD recorder, CD player, DVD/LD player, etc.), press the

button on the component selector, TAPE/MD, CD, DVD/

LD, etc., for the component you want to control. (See

“SETUP CODES” on page 53.)

1 Set VOLUME to the “ ” position.

Front panel

2 Turn the power on.

Front panel Remote control

2 1,73

Front panel

01RX-V495-e/f-3 6/22/99, 1:33 PM28

English

7 Adjust the volume to the desired output level.

Front panel Remote control

8 If desired, adjust BASS, TREBLE, BALANCE, etc.

and use the digital sound field processor (see

page 38).

BASS: Turn this control clockwise to increase (or

counterclockwise to decrease) the low-

frequency response.

TREBLE: Turn this control clockwise to increase (or

counterclockwise to decrease) the high-

frequency response.

BALANCE: Adjust the balance of the output volume

from the left and right speakers to

compensate for sound imbalance caused

by the speaker location or listening room

conditions.

Front panel

* These controls are only effective for the sound from the

main speakers.

When you have finished using this unit

Press STANDBY/ON on the front panel again or POWER on

the remote control transmitter to set this unit to the standby

mode.

4 For a DVD/LD or TV/DBS source, the current input

mode is also shown.

* To change the input mode for the DVD/LD or TV/DBS

source, press INPUT MODE (or the button that you

have pressed to select the program source in step 3

on the remote control transmitter) once or more until

the desired input mode (AUTO or ANALOG) is shown

on the display. (See page 30 for details on switching

the input mode.)

Front panel Remote control

Input mode

5 Select the main speakers to be used.

Front panel

* If you use two main speaker systems, press both A and B.

6 Play the source. (See page 32 for detailed information

on tuning.)

01RX-V495-e/f-3 6/22/99, 1:33 PM29

Notes on using INPUT

• The audio source selected by INPUT will not be played if the

“TAPE/MD MON” indicator lights up or if “EXT. DECDR” is

displayed.

• If you select INPUT for a video source without canceling the

selection of TAPE/MD MON / EXT. DECODER on the front

panel (or TAPE/MD or EXT. DEC. on the remote control

transmitter), the play back result will be a video image from

the video source and the sound from the audio source

selected by TAPE/MD MON / EXT. DECODER on the front

panel (or TAPE/MD or EXT. DEC. on the remote control

transmitter).

• Once you start playing a video source, the video image will

not be interrupted even if INPUT for an audio source is

selected.

• When you select a program source by using INPUT, the DSP

program (or no DSP program) that was being used when the

same program source was selected the last time, will be

automatically recalled.

Switching the input mode

(for DVD/LD and TV/DBS)

This unit allows you to switch the input mode only for those

sources connected to the DVD/LD and TV/DBS input terminals

(on the rear panel of this unit) that input two or three types of

signal.

The following two input modes are provided:

AUTO For a source connected to the DVD/LD input

terminals

This mode is automatically selected when you turn on

the power to this unit. In this mode, the input signal is

automatically selected in the following order of priority:

1. Digital input signal from the COAXIAL terminal

2. Digital input signal from the OPTICAL terminal

3. Analog input signal

For a source connected to the TV/DBS input

terminals

This mode is selected when you turn on the power to

this unit if the AUTO position is selected for “INPUT” in

the SET MENU mode. (See page 45 for details.) In

this mode, the input signal is automatically selected in

the following order of priority:

1. Digital input signal from the OPTICAL terminal

2. Analog input signal

ANALOG

In this mode, only an analog input signal is selected,

even if a digital signal is input at the same time.

Select this mode when you want to use the analog

input signal instead of the digital input signal.

Notes on input mode selection

• To play back a source that is Dolby Digital-decoded, set the

input mode to AUTO.

• For the TV/DBS source only, the input mode selected for

“INPUT” in the SET MENU mode is effective when you turn

on the power to this unit.

• When you want to enjoy a source which has normal

2-channel signals with a Dolby Pro Logic Surround program,

select the ANALOG mode.

• In the AUTO mode, there may be a case, depending on the

LD player or DVD player, that when you search for a source

encoded with Dolby Digital during play and then play is

restored, the sound output is interrupted for a moment

because the digital input signal is selected again.

01RX-V495-e/f-3 6/22/99, 1:33 PM30

English

1,4

4 21

TO RECORD A SOURCE ON TAPE OR MD

1 Select the source to be recorded.

Front panel Remote control

2 Play the source and then turn up the volume to confirm

the program source. (See page 32 for detailed

information on tuning.)

Front panel Remote control

3 Begin recording on the tape deck, MD recorder or VCR

connected to this unit.

4 When a tape deck or MD recorder is being used for

recording, you can monitor the sounds being recorded

by pressing TAPE/MD MON / EXT. DECODER on the

front panel or TAPE/MD on the remote control

transmitter so that the “TAPE/MD MON” indicator lights

up on the display.

Front panel Remote control

Notes

• The settings of DSP and VOLUME, BASS, TREBLE and

BALANCE have no effect on the material being recorded.

• A source that is connected to this unit only through the digital

terminals cannot be recorded by a tape deck, MD recorder or

VCR connected to this unit.

• Please check the copyright laws in your country to record

from records, compact discs, radio, etc. Recording of

If you use a video source that has scrambled or encoded

signals to prevent it from being dubbed, there may be a case

that the picture itself will be affected by those signals.

01RX-V495-e/f-3 6/22/99, 1:33 PM31

AUTOMATIC TUNING

1 Select the reception band (FM or AM) and confirm it on

the display.

Front panel

2 Press TUNING MODE so that the “AUTO TUNING”

indicator lights up on the display.

Front panel

Lights up

3 To tune in to a higher frequency, press the UP side of

TUNING once.

To tune in to a lower frequency, press the DOWN side

of TUNING once.

Front panel

* If the station where the tuning search stops is not the

desired one, press once more.

* If the tuning search does not stop at the desired station

(because the signal from the station is weak), take the

manual tuning procedure.

TUNING OPERATIONS

Set INPUT on the front panel to the TUNER position. When using the remote control transmitter, press AMP<TUNER> on the

component selector and then press TUNER on the input selector.

Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is

possible. However, if the signal from the station you want to select is weak, you must tune in to it manually (MANUAL TUNING).

MANUAL TUNING

1 Select the reception band (FM or AM) and confirm it on

the display.

Front panel

2 Press TUNING MODE.

Front panel

3 Tune in manually to the desired station.

Front panel

* To continue the tuning search, press and hold the button.

Note

If you tune in manually to an FM station, it will be automatically

received in monaural mode to increase the signal quality.

Confirm that the “AUTO

TUNING” indicator goes off.

01RX-V495-e/f-3 6/22/99, 1:33 PM32

English

2 4



MANUAL PRESET TUNING

This unit can store station frequencies to be selected by tuning. With this function, you can recall any desired station simply by

selecting the preset station number with which it was stored. Up to 40 stations (8 stations x 5 groups) can be stored.

4 Select the preset station number with which you want to

store the station before the “MEMORY” indicator goes

off from the display.

Front panel

The displayed station has been stored as A1.

* In the same way, store other stations as A2, A3 ... A8.

* You can store more stations as preset station numbers in

other groups in the same way by selecting another group

in step 2.

To store stations

1 Tune in to the desired station.

(See the previous page for the tuning procedure.)

2 Press A/B/C/D/E once or more to select the desired

group (A to E) of preset stations and confirm it on the

display.

Front panel

3 Press MEMORY so that the “MEMORY” indicator

flashes for about five seconds.

Front panel

Flashes

01RX-V495-e/f-3 6/22/99, 1:33 PM33

To recall a preset station

1 Select the group of preset stations.

Front panel Remote control

2 Select the preset station number.

Front panel Remote control

Notes

• A new setting can be stored in place of the former one.

• For presets, the setting of the reception mode (stereo or

monaural) is stored along with the station frequency.

Memory back-up

The memory back-up circuit prevents the stored data from

being lost when this unit is set in the standby mode. If,

however, the power plug is disconnected from the AC outlet or

the power is cut due to temporary power failure for more than

one week, the memory will be erased. If so, it can be re-stored

by simply following the preset tuning procedure.

1 2

01RX-V495-e/f-3 6/22/99, 1:33 PM34

English

3 1

To store stations

1 Select the FM band.

Front panel

2 Press TUNING MODE so that the “AUTO TUNING”

indicator lights up on the display.

Front panel

Lights up

3 Press MEMORY and hold for about three seconds.

Front panel

Flashes

AUTOMATIC PRESET TUNING (for FM stations only)

You can also make use of the automatic preset tuning function for FM stations only. This function enables the unit to perform

automatic tuning and to sequentially store FM stations with strong signals. Up to 40 stations can be stored automatically in the

same way as that for manual preset tuning on page 33. Note that a new setting can be stored in place of the former one.

4 To tune in to higher frequencies, press the UP side of

TUNING once.

To tune in to lower frequencies, press the DOWN side

of TUNING once.

Front panel

* If TUNING is not pressed, the automatic preset tuning

soon begins automatically toward higher frequencies.

Automatic preset tuning begins from the frequency currently

displayed. Received stations are sequentially stored as A1,

A2 ... A8.

* If more than 8 stations are received, they are stored as the

preset station numbers in other groups (B, C, D and E) in

that order.

If you want to store the first station received by automatic

preset tuning as a desired preset station number

For example, if you want to store the first received station as C5,

select “C5” while “A1”, the “MEMORY” indicator and the “AUTO

TUNING” indicator flash after pressing MEMORY in step 3. Then

press TUNING. The first received station is stored as C5, and the

next stations as C6, C7 ... sequentially.

If stations have been stored up to E8, automatic preset tuning

automatically stops.

When automatic preset tuning is complete

The display shows the frequency of the last preset station.

Check the contents and the number of preset stations by

following the procedure in the section “To recall a preset

station” on page 34.

01RX-V495-e/f-3 6/22/99, 1:33 PM35

EXCHANGING PRESET STATIONS

You can exchange the assigment of two preset stations with each other as shown below.

3 Next, recall preset station “A5” by following the same

procedure as in step 1.

Flashes

4 Press EDIT once more.

Front Panel

Shows the exchange of

stations has been

completed.

Notes

• You can manually replace a preset station with another FM or AM station by simply following the procedure in the section “To

store stations” on page 33.

• Even if the number of received stations is not enough to be stored up to E8, the search is automatically ended after searching all

frequencies.

• With this function, only FM stations with sufficient signal strength are automatically stored. If the station you want to store is weak

in signal strength, tune in to it manually in monaural sound and store it by following the procedure in the section “To store

stations” on page 33.

Example

If you want to change the preset station from “E1” to “A5”, or vice versa.

1 Recall preset station “E1” by following the procedure in

the section “To recall a preset station” on page 34.

2 Press EDIT.

Front Panel

Flashes

2,4

01RX-V495-e/f-3 6/22/99, 1:33 PM36

English

SETTING THE SLEEP TIMER

The SLEEP timer can be used to make this unit automatically switch to the standby mode. When you are going to sleep while

enjoying a broadcast or other desired program source, this timer function is useful. The SLEEP timer can only be controlled with

the remote control transmitter.

Notes

• To set the SLEEP timer for this unit, press AMP<TUNER>, TAPE/MD, CD or DVD/LD on the component selector.

• The components for which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear

panel of this unit.

To set the SLEEP time

1 Press SLEEP once or more to select the desired

SLEEP time.

Remote control

The SLEEP time is displayed.

Flashes

Each time you press SLEEP, the SLEEP time will change as

follows:

(Minutes)

120 90 60 30

The SLEEP timer is off (SLEEP OFF).

(This is the state before SLEEP

is pressed.)

The “SLEEP” indicator soon lights up and the display returns

to the indication before the SLEEP timer was set.

2 The unit will be switched to the standby mode

automatically at the selected SLEEP time.

To cancel the selected SLEEP time

Remote control

Press SLEEP once or more so that “SLEEP OFF” appears on

the display. (It will soon disappear and the “SLEEP” indicator

will go off from the display.)

Note

The SLEEP timer setting can also be canceled by setting the

unit in the standby mode with STANDBY/ON on the front panel

(or POWER on the remote control transmitter) or by

disconnecting the power plug of the unit from the AC outlet.

01RX-V495-e/f-3 6/22/99, 1:33 PM37

No. PROGRAM

1 DOLBY PRO LOGIC ( )

This functions when the input signal is analog or

PCM audio, or encoded with Dolby Digital in

2-channel.

Speaker output: main, center, rear

DOLBY DIGITAL (

)

This functions when the input signal is encoded with

Dolby Digital (not in 2-channel).

Speaker output: main, center, rear

2 DOLBY PRO LOGIC ENHANCED

(

)

This functions when the input signal is analog or

PCM audio, or encoded with Dolby Digital in

2-channel.

Speaker output: main, center, rear

DOLBY DIGITAL ENHANCED

(

)

This functions when the input signal is encoded with

Dolby Digital (not in 2-channel).

Speaker output: main, center, rear

3 70 mm MOVIE THEATER

(

)

This functions when the input signal is analog or

PCM audio, or encoded with Dolby Digital in

2-channel.

Speaker output: main, center, rear

DIGITAL MOVIE THEATER

(

)

This functions when the input signal is encoded with

Dolby Digital (not in 2-channel).

Speaker output: main, center, rear

FEATURES

This reproduces video discs, video tapes and similar sources

which are Dolby Surround encoded and bear the “DOLBY

SURROUND” logo.

The built-in Dolby Pro Logic Surround decoder or Dolby Digital

decoder precisely reproduces the sounds and sound effects of

a source encoded with Dolby Surround. The realization of a

highly efficient decoding process improves crosstalk and

channel separation and makes sound positioning smoother

and more precise.

Note: If the main channel sound is considerably altered by

overadjusting BASS or TREBLE, it may not produce suitable

surround sound.

This reproduces video discs, video tapes and similar sources

which are Dolby Surround encoded and bear the “DOLBY

SURROUND” logo.

This program ideally simulates the multi-surround speaker

systems of the 35 mm film theater. Dolby Surround decoding

is precisely performed without altering the original sound

orientation. The surround effects produced by this sound field

fold around the viewer naturally from the rear to the left and

right and toward the screen.

This is ideal for reproducing video discs, video tapes and

similar sources which are Dolby Surround encoded and bear

the “DOLBY SURROUND” logo.

This program is ideal for precisely reproducing the sound

design of the newest 70 mm/Dolby Digital multi-track films.

The sound field is similar to that of the newest movie theaters,

so the reverberations of the sound field itself are restrained as

much as possible. The three-dimensional feeling of the sound

field is emphasized, and dialog is precisely oriented on the

screen. You can enjoy watching Sci-Fi, adventure movies, etc.

with considerable presence.

USING THE DIGITAL SOUND FIELD PROCESSOR

(

DSP

)

This unit incorporates a sophisticated, multi-program digital sound field processor. The processor allows you to electronically

expand and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in

your listening room. You can create outstanding audio sound by selecting a suitable sound field program (this will, of course,

depend on what you are listening to) and adding any desired adjustments.

The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most

of these are precise digital re-creations of actual acoustic environments. The data for these sound fields were recorded at actual

locations using sophisticated sound field measurement equipment.

Note

The channel level balance between the left and right rear speakers may vary depending on the sound field you are

listening to. This is due to the fact that most of these sound fields are a re-creation of actual acoustic environments.

BRIEF OVERVIEW OF DIGITAL SOUND FIELD PROGRAMS

01RX-V495-e/f-4 6/22/99, 1:33 PM38

English

FEATURES

This program is designed specifically to enhance mono audio

sources. Compared to a strictly mono setting, the sound image

created in this mode is wider and slightly forward of the speaker

pair, lending an immediacy to the overall sound. It is particularly

effective when used with old mono movies, news broadcasting

and dialog.

This program is furnished with a tight sound field in which the

sound will not spread excessively on the front side, but the rear

surround side produces dynamic sound expansion. This

program is the most suitable for sports events.

This program re-creates the acoustic environment of a lively

disco in the heart of a very lively city. The sound is dense and

highly concentrated. It is also characterized by a high-energy,

“immediate” sound.

This program is ideally suited for rock music. You will

experience a very dynamic and lively sound field.

In this program, the center will appear to be deep behind the

main speakers, creating an expansive, large hall ambience.

Orchestra and opera music are suited to this sound field.

No. PROGRAM

4 MONO MOVIE

(

)

This functions when the input signal is analog or

PCM audio, or encoded with Dolby Digital in

2-channel.

Speaker output: main, center, rear

(

)

This functions when the input signal is encoded

with Dolby Digital (not in 2-channel).

Speaker output: main, center, rear

5 TV SPORTS

(

)

This functions when the input signal is analog or

PCM audio, or encoded with Dolby Digital in

2-channel.

Speaker output: main, center, rear

(

)

This functions when the input signal is encoded

with Dolby Digital (not in 2-channel).

Speaker output: main, center, rear

6 DISCO

(

)

This functions when the input signal is analog or

PCM audio, or encoded with Dolby Digital in

2-channel.

Speaker output: main, rear

(

)

This functions when the input signal is encoded

with Dolby Digital (not in 2-channel).

Speaker output: main, center, rear

7 ROCK CONCERT

(

)

This functions when the input signal is analog or

PCM audio, or encoded with Dolby Digital in

2-channel.

Speaker output: main, rear

(

)

This functions when the input signal is encoded

with Dolby Digital (not in 2-channel).

Speaker output: main, center, rear

8 CONCERT HALL

(

)

This functions when the input signal is analog or

PCM audio, or encoded with Dolby Digital in

2-channel.

Speaker output: main, rear

(

)

This functions when the input signal is encoded

with Dolby Digital (not in 2-channel).

Speaker output: main, center, rear

Note: When the NONE position is selected for “CNTR” in the SET MENU mode, no sound is output from the center speaker(s).

01RX-V495-e/f-4 6/22/99, 1:33 PM39

PLAYING AN AUDIO/VIDEO SOURCE WITH THE DIGITAL SOUND FIELD

PROCESSOR (DSP) EFFECT

1 Follow steps 1 to 7 shown in “BASIC OPERATIONS” on

pages 28 to 29.

2 Select the desired DSP program that is suitable for the

source. When using the remote control transmitter,

press AMP<TUNER> on the component selector first.

Front panel Remote control

The name of the selected program appears

on the display.

3 If desired, adjust the delay time and the output level of

each speaker. (See pages 42 and 43 for details.)

Notes

• You can select a program for each of the program sources.

Once you select a program, it is linked with the program

source selected at that time. So, when you select the

program source next time, the same program is automatically

called.

• If you prefer to cancel the DSP function, press EFFECT. The

sound will be that of normal 2-channel stereo without a

surround sound effect.

• When a monaural sound source is played with DOLBY PRO

LOGIC or DOLBY PRO LOGIC ENHANCED, no sound can

be heard from the main speakers and the rear speakers.

Sound is heard only from the center speaker. However, if the

NONE position is selected for “CNTR” in the SET MENU

mode, the main speakers output the sound of the center

channel.

01RX-V495-e/f-4 6/22/99, 1:33 PM40

English

To enjoy a video source with Dolby Pro Logic

Surround or Dolby Digital-decoded

When you select the DOLBY PRO LOGIC/DOLBY DIGITAL,

DOLBY PRO LOGIC ENHANCED/DOLBY DIGITAL

ENHANCED or 70 mm MOVIE THEATER/DIGITAL MOVIE

THEATER program, and the input signal of the source is

2-channel stereo, Dolby Pro Logic Surround is decoded. When

a program is selected and the input signal of the source is

encoded with Dolby Digital, Dolby Digital is automatically

decoded.

* The following indicators on the display show you what sound

processing is being undertaken.

This lights up when Dolby Digital is being decoded and the

input signal of the selected source encoded with Dolby Digital

is not in 2-channel.

This lights up when the digital sound

field processor is turned on.

This lights up when Dolby Pro

Logic Surround is being decoded.

* In addition, for the DOLBY PRO LOGIC/DOLBY DIGITAL,

DOLBY PRO LOGIC ENHANCED/DOLBY DIGITAL

ENHANCED or 70 mm MOVIE THEATER/DIGITAL MOVIE

THEATER program, the name of the program on the display

will change according to the type of decoding. (See page 38

for details.)

Note

If the input signal of the source is encoded with Dolby Digital in

2-channel only, their sound processing is similar to that for

analog or PCM audio signals.

To cancel the sound effect

EFFECT on the front panel and on the remote control

transmitter make it simple to compare the normal stereo sound

with the fully processed sound effect.

To cancel the sound effect and monitor only the main sound,

press EFFECT. Press EFFECT once more to turn sound effect

on.

Front panel Remote control

Notes

• If the sound effect is canceled when signals encoded with

Dolby Digital are input to this unit, the signals of all channels

are mixed and are output from the main speakers.

• If EFFECT is pressed to turn sound effects off when Dolby

Digital is decoded, it may happen that the sound is output

faintly or not output normally, depending on the source. In

that case, press EFFECT to turn sound effects on, or use

input signals not encoded with Dolby Digital.

This unit incorporates a Dolby Digital decoder and a Dolby Pro Logic Surround decoder for multi-channel sound reproduction of

sources encoded with Dolby Surround. The operation of these decoders can be controlled by selecting a corresponding DSP

program including the combined operation of YAMAHA DSP and Dolby Digital or Dolby Pro Logic Surround.

01RX-V495-e/f-4 6/22/99, 1:33 PM41

2 Press + or – to adjust the settings for the delay time or

speaker output levels.

Front panel Remote control

3 Repeat steps 1 to 2 to adjust the settings of any other

item.

ADJUSTING THE DELAY TIME AND SPEAKER OUTPUT LEVELS

When using the digital sound field processor with the Dolby Pro Logic Surround decoder or the Dolby Digital decoder, you can

adjust the delay time between the main sound and sound effect, and each speaker’s output level as you prefer.

Adjusting method

When adjusting with the remote control transmitter, press

AMP<TUNER> on the component selector.

1 Press TIME/LEVEL once or more until the name of the

item which you want to adjust appears on the display.

Front panel Remote control

When pressed, the selection changes as follows:

DELAY

CENTER

R SUR.

L SUR.

SWFR

* Depending on the setting in the SET MENU mode, you

may not be able to select all items.

Delay time

Center speaker output level

Right rear speaker output level

Left rear speaker output level

Subwoofer output level

01RX-V495-e/f-4 6/22/99, 1:33 PM42

English

Adjusting the delay time

You can adjust the time difference between the beginning of the

sound from the main speakers and the beginning of the sound

effect from the rear speakers.

The larger the value, the later the sound effect is generated.

This adjustment can be individually made to all programs.

Notes

• Adding too much delay will cause an unnatural effect with

some sources.

• When + or – is pressed, the sound is momentarily

interrupted.

Adjusting the output level of the center, right rear and left rear speakers, and subwoofer

Program

1. DOLBY PRO LOGIC

DOLBY DIGITAL

2. DOLBY PRO LOGIC ENHANCED

DOLBY DIGITAL ENHANCED

3. 70 mm MOVIE THEATER

DIGITAL MOVIE THEATER

4. MONO MOVIE

5. TV SPORTS

6. DISCO

7. ROCK CONCERT

8. CONCERT HALL

If desired, you can adjust the sound output level of each

speaker even if the output level has already been set in

“SPEAKER BALANCE ADJUSTMENT” on pages 25 to 27.

Notes

• The output level of the center speaker cannot be adjusted

when the DISCO, ROCK CONCERT or CONCERT HALL

program is selected, and the input signal is analog, PCM

audio, or encoded with Dolby Digital in 2-channel format.

• If the function “CNTR” in the SET MENU mode is set to the

NONE position, the sound output level of the center speaker

cannot be adjusted. This is because, in this mode, the center

sound is automatically output from the left and right main

speakers.

• Once the output level has been adjusted, the level will be the

same for all digital sound field programs.

Speakers

CENTER

RIGHT REAR

LEFT REAR

SUBWOOFER

Control range (dB)

MIN, –20 to +10

MIN, –20 to 0

Preset value

Control range (ms)

15 to 30

0 to 15

15 to 30

0 to 15

15 to 30

1 to 99

Memory back-up

The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the

power plug is disconnected from the AC outlet or the power is cut due to temporary power failure for more than one week, the

values for the delay time and the center/rear/subwoofer output levels you set the last time will automatically return to the preset

values. If so, they can be re-set by simply following the adjusting method on page 42.

01RX-V495-e/f-4 6/22/99, 1:33 PM43

D.RNG (Adjusting the dynamic range)

Choices: MAX/STD/MIN

Preset position: MAX

* This adjustment is effective only when Dolby Digital is

decoded.

MAX: “Dynamic range” is the difference between the

maximum level and the minimum level of sounds.

Sounds on a movie originally designed for movie

theaters feature very wide dynamic range. Dolby

Digital technology can modify the original sound

track into a home audio format with this wide

dynamic range unchanged.

In this position, a source encoded with Dolby Digital

is reproduced in the original sound track’s wide

dynamic range providing you with powerful sounds

just like those in a movie theater. Selecting this

position will be even better if you can listen to a

source at a high output level in a room specially

soundproofed for audio/video enjoyment.

STD (Standard):

Powerful sounds of extremely wide dynamic range

are not always suitable for home use. Depending on

the condition of your listening environment, it may

not be possible to increase the sound output level as

high as that in a movie theater. However, at the

normal level suitable for listening to in your room, the

low-level parts of source sound often cannot be

heard well because they will be lost among noise in

your environment. Dolby Digital technology has also

made it possible to reduce an original sound track’s

dynamic range for a home audio format by

“compressing” the sound data.

In this position, a source encoded with sound Dolby

Digital is reproduced in the “compressed” dynamic

range of sound that is suitable for low-level listening.

MIN: In this position, the dynamic range is more reduced

than in the STD position.

Selecting this position will be effective when you

must listen to a source at a low level.

ADJUSTMENTS IN THE “SET MENU” MODE

The following ten types of functions maximize the performance of your system and expand your enjoyment for audio listening and

video watching.

1. CNTR (CENTER SPEAKER)

2. REAR (REAR SPEAKERS)

3. MAIN (MAIN SPEAKERS)

4. BASS (LFE/BASS OUT)

5. M.LVL (MAIN LEVEL)

For details on “CNTR”, “REAR”, “MAIN”, “BASS” and “M.LVL”,

see page 23. (Once you have selected the appropriate modes,

you do not have to change settings unless any alteration is

made in your speaker system.)

LFE [Adjusting the output level of the

LFE (low frequency effect) channel]

Control range: –20 dB to 0 dB (in 1 dB steps)

Preset value: 0 dB

* This adjustment is effective only when Dolby Digital is

decoded and the signals of the selected source encoded with

Dolby Digital contain LFE signals.

This adjusts the output level of the LFE channel. If the LFE

signals are mixed with signals of other channels to output them

from the same speakers, the ratio of the LFE signal level to the

level of the other signals is adjusted.

(See page 7 for details about the LFE channel.)

6. LFE (LFE LEVEL)

7. D.RNG (DYNAMIC RANGE)

8. C.DELAY (CENTER DELAY)

9. GUARD (MEMORY GUARD)

10. INPUT (INPUT MODE)

01RX-V495-e/f-5 6/22/99, 1:33 PM44

English

C.DELAY [Adjusting the delay of

center sounds (dialog, etc.)]

Control range: 0 ms to 5 ms (in 1 ms steps)

Preset value: 0 ms

* This adjustment is effective only when Dolby Digital is

decoded and the signals of the selected source encoded with

Dolby Digital contain center-channel signals.

This adjusts the delay between the main sound (on the main

channels) and dialog, etc. (on the center channel).

The larger the value, the later the dialog, etc. is generated.

This is for making sounds from the left main, center and right

main speakers reach your listening position at the same time.

This is achieved by delaying the sound from the center speaker

if the distance from the center speaker to your listening position

is shorter than the distance from the left or right main speaker

to your listening position.

GUARD

Choices: ON/OFF

Preset position: OFF

If you wish to prevent accidental alterations to SET MENU and

other adjustments on this unit, select ON. The following

functions on this unit can be locked by this operation:

• Functions in the SET MENU mode

• Functions in the TIME/LEVEL mode

• Functions when using TEST

INPUT (Selecting the initial input mode of

the sources connected to the TV/DBS

input terminals)

Choices: AUTO/LAST

Preset position: AUTO

You can designate the input mode that is automatically selected

when the power for this unit is switched on for only the sources

connected to the TV/DBS input terminals of this unit.

AUTO: In this position, the AUTO input mode is always

selected when the power for this unit is switched on.

LAST: In this position, the input mode you selected last time

is memorized and will not be changed when the

power is switched on again.

* See page 30 for details on switching the input mode.

Adjusting method

Adjustments should be made while watching the information on

this unit’s display.

When adjusting with the remote control transmitter, press

AMP<TUNER> on the component selector.

Press SET MENU once or more so that the function which you

want to change appears on the display.

Front panel Remote control

Press + or – to select any desired setting or to edit parameters

of the function.

Front panel Remote control

Repeat these steps to change or adjust the settings of any

other function.

Memory back-up

The memory back-up circuit prevents the stored data from

being lost when this unit is set in the standby mode. If,

however, the power plug is disconnected from the AC outlet or

the power is cut due to temporary power failure for more than

one week, the settings of the SET MENU mode will

automatically return to the factory settings. If so, they can be

re-set by simply following the procedure above.

01RX-V495-e/f-5 6/22/99, 1:33 PM45

Components which can be controlled

There are eight buttons on the component selector that you can select to control connected components with this remote control

transmitter. For example, if CD on the component selector is pressed, the remote control transmitter selects the CD operation

mode, allowing the CD player to be operated by the buttons on the remote control transmitter.

Notes

1. You can preset the code for the manufacturer of your component after pressing the shaded buttons in the illustration above.

Note that you can preset only one code for one mode. See “SETUP CODES” on page 53 for details.

2. In the DVD/LD and DVD MENU modes:

• Be sure to press DVD/LD on the component selector before presetting the code for the DVD/LD player. The code preset in

the DVD/LD mode is also simultaneously preset in the DVD MENU mode. You cannot preset the code for a DVD player in

the DVD MENU mode.

• DVD MENU operations cannot be performed for some DVD players.

3. When using a second (and third) VCR: (See “To use a second (and third) VCR” on page 53 for details.)

• If you are not using a CBL/DBS (cable TV or DBS tuner), the second (or third) VCR can be preset in the CBL/DBS mode.

• If you are not using a DVD player, the second (or third) VCR can be preset in the DVD MENU mode. Note that in this case

you must preset the code for an LD player in the DVD/LD mode even if an LD player is not being used.

You can use the remote control transmitter to control not only this unit but also other components connected to it. The remote

control transmitter is factory set to control this unit and most YAMAHA audio components. To control other brands of components,

you must preset the remote control transmitter with manufacturers’ codes listed on pages 113 to 117.

REMOTE CONTROL TRANSMITTER

TAPE/MD

The code for a YAMAHA tape deck is

preset. (The code for the YAMAHA MD

recorder can also be preset.)

The code for a YAMAHA CD player is preset.

DVD/LD & DVD MENU

An LD player can be controlled in the DVD/LD

mode. A DVD player can be controlled in the

DVD/LD and DVD MENU modes. The code for

a YAMAHA DVD player is preset. If the remote

control transmitter will not operate your

YAMAHA DVD player, you need to preset code

number “0048”.

AMP<TUNER>

You can perform the basic operations of this unit,

set the speaker level, and set the DSP level and

delay time in the AMP<TUNER> mode.

VCR

A VCR can be controlled.

CBL/DBS

A cable television or DBS tuner can be

controlled.

A television can be controlled.

01RX-V495-e/f-6 6/22/99, 1:33 PM46

English

TV VOLUME

EFFECT

This button switches the DSP

program on or off.

PRG+/PRG–

These buttons select a DSP program.

SET MENU

This button selects functions in the SET

MENU mode.

Input selector

These buttons select the program source.

CD: To play a CD

TUNER: To listen to an FM or AM

broadcast

TAPE/MD: To play a tape or MD

DVD/LD: To play a DVD or LD

TV/DBS: To watch a television or

satellite broadcast

VCR: To play a video tape

PHONO: To play an analog record

V-AUX: To use a camcorder

EXT. DEC.: To output the signals of a DTS

or other multi-channel

decoder

TV INPUT

VOLUME (

)

These buttons adjust the volume level.

MUTE

This button mutes the sound. To cancel mute,

press this button once more, or press any

operation buttons of this unit.

+/–

These buttons adjust the settings of the SET

MENU mode and the TIME/LEVEL mode.

TEST

This button outputs a test tone for adjusting

the output levels of the speakers.

SLEEP

This button sets the SLEEP timer.

A/B/C/D/E & PRESET +/–

These buttons select a preset FM or AM

broadcast.

A/B/C/D/E: To select a group of preset

stations.

PRESET +/–: To select the preset station

number.

Press AMP<TUNER>.

POWER

Each time this button is pressed, the unit

will switch between the power on and

standby modes.

The lightly marked buttons do not function.

■AMP<TUNER> MODE

Note:

TV VOLUME and TV INPUT function if you have preset the code for your TV.

TIME/LEVEL

This button selects the item in the TIME/LEVEL

mode.

01RX-V495-e/f-6 6/22/99, 1:33 PM47

The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component.

TV VOLUME

■TAPE/MD MODE

Notes: •

TV VOLUME functions if you have preset the code for your TV.

• The code for the YAMAHA MD recorder can be preset.

POWER

(TAPE) When you have preset the code for

a YAMAHA tape deck, this button turns the

unit on. When you have preset the code for

another manufacturer, this button turns on

that component if it has a remote control

transmitter with a power button.

(MD) When you have preset the code for the

YAMAHA MD recorder, this button turns the

unit on.

REC/PAUSE

This button pauses recording on a tape

deck or MD recorder.

DIR A (TAPE)

This button selects the playing direction of

deck A.

SKIP– (MD)

This button skips to the previous track.

PLAY

This button plays a tape or an MD.

REWIND (TAPE)

This button rewinds a tape.

SEARCH (MD)

This button initiates a backward search on

the track that is playing to find the point from

which you want to listen.

DECK A/B (TAPE)

This button selects double-cassette tape

deck A or B.

DIR B (TAPE)

This button selects the playing direction of

deck B.

SKIP+ (MD)

This button skips to the next track.

STOP

This button stops operation of a tape or

MD.

FAST FORWARD (TAPE)

This button winds a tape fast forward.

SEARCH (MD)

This button initiates a fast-forward search

on the track that is playing to find the point

from which you want to listen.

DISPLAY (MD)

PAUSE (MD)

This button gives a pause in operation.

Press TAPE/MD.

INPUT

EFFECT

SLEEP

MUTE

VOLUME

01RX-V495-e/f-6 6/22/99, 1:33 PM48

English

TV VOLUME

TV INPUT

The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component.

■CD MODE

Note: TV VOLUME and TV INPUT function if you have preset the code for your TV.

POWER

When you have preset the code for a

YAMAHA CD player, this button turns the

unit on. When you have preset the code for

another manufacturer, this button turns on

that component if it has a remote control

transmitter with a power button.

DISC SKIP +/–

(for the CD player with CD changer)

These buttons skip to the next or previous

CD.

SKIP–

This button skips to the previous track.

PLAY

This button plays a CD.

This button initiates a backward search on

the track that is playing to find the point from

which you want to listen.

PAUSE

This button gives a pause in operation. The

button functions as PAUSE/STOP* for operating

YAMAHA CD player under factory setting.

STOP

This button stops operation. The button

functions as PAUSE/STOP* for operating

YAMAHA CD players.

This button initiates a fast-forward search

on the track that is playing to find the point

from which you want to listen.

DISPLAY

Press CD.

INPUT

EFFECT

SLEEP

MUTE

VOLUME

SKIP+

This button skips to the next track.

* PAUSE/STOP function ... Press the button once to give a pause in operation and once more to stop operation.

01RX-V495-e/f-6 6/22/99, 1:33 PM49

■DVD MENU MODE

The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component.

DISC SKIP +/–

SKIP–

PLAY

DISPLAY

PAUSE

STOP

Numeric buttons

+10

DISC SKIP +/–

MENU LEFT

MENU SELECT

TITLE

CLEAR

INDEX

MENU UP

MENU RIGHT

MENU DOWN

RETURN

Note: TV VOLUME and TV INPUT function if you have

preset the code for your TV.

■DVD/LD MODE

Note: TV VOLUME and TV INPUT function if you have

preset the code for your TV.

TV VOLUME

TV INPUT

TV VOLUME

TV INPUT

POWER

When you have preset the code for a YAMAHA DVD

player, this button turns the unit on. When you have

preset the code for another manufacturer, this button

turns on that component if it has a remote control

transmitter with a power button.

Press DVD/LD.

Press DVD MENU.

INPUT

EFFECT

SLEEP

MUTE

VOLUME

SKIP+

MUTE

VOLUME

POWER

(DVD) When you have preset the code for

a YAMAHA DVD player, this button turns

the unit on. When you have preset the

code for another manufacturer, this button

turns on that component if it has a remote

control transmitter with a power button.

(LD) When you have preset the code for a

YAMAHA LD player, this button turns the

unit on. When you have preset the code

for another manufacturer, this button turns

on that component if it has a remote

control transmitter with a power button.

01RX-V495-e/f-6 6/22/99, 1:33 PM50

English

■CBL/DBS MODE

Note: TV VOLUME, TV INPUT and TV SLEEP

function if you have preset the code for your TV.

■VCR MODE

Note: TV VOLUME, TV INPUT and TV SLEEP function if you

have preset the code for your TV.

VCR POWER

DISPLAY

CHANNEL

CHANNEL ENTER

VCR REC

Press this button twice

to start recording.

VCR CHANNEL +/–

VCR PLAY

VCR REWIND

VCR PAUSE

VCR STOP

VCR

FAST FORWARD

CBL/DBS POWER

DISPLAY

CHANNEL

CHANNEL ENTER

MENU LEFT

CBL/DBS CHANNEL +/–

MENU SELECT

MENU UP

MENU RIGHT

MENU DOWN

+100

TV SLEEP

■TV MODE

Note: You can control your VCR if you have preset the code for

it.

DISPLAY

CHANNEL

CHANNEL ENTER

TV MUTE

TV CHANNEL +/–

TV SLEEP

TV INPUT

EFFECT

TV VOLUME

The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component.

TV VOLUME

TV INPUT

TV VOLUME

TV INPUT

VCR REC

Press this button twice.

VCR REWIND

VCR PLAY

VCR PAUSE

VCR STOP

VCR

FAST FORWARD

Press VCR.

Press TV.

Press CBL/DBS.

MUTE

VOLUME

TV SLEEP

EFFECT

TV POWER

VOLUME

MUTE

VOLUME

RECALL

01RX-V495-e/f-6 6/22/99, 1:33 PM51

NOTES ABOUT THE REMOTE CONTROL TRANSMITTER

Battery installation Remote control transmitter operation range

Notes

• There should be no large obstacles between the remote

control transmitter and the unit.

• If the remote control sensor is directly illuminated by strong

lighting (especially an inverter type of fluorescent lamp, etc.),

it might cause the remote control transmitter not to work

correctly. In this case, reposition the unit to avoid direct

lighting.

Battery replacement

If the remote control transmitter operates only when it is close

to the unit, the batteries are weak. Replace all batteries with

new ones.

Be sure to replace batteries within about two minutes. If it

takes longer than two minutes, the codes preset for the

remote control transmitter will return to the factory-set.

Notes

• Use only AAA, R03, UM-4 batteries for replacement.

• Be sure the battery polarity is correct. (See the illustration

inside the battery compartment.)

• Remove the batteries if the remote control transmitter will not

be used for an extended period of time.

• If the batteries have leaked, dispose of them immediately.

Avoid touching the leaked material or letting it come into

contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

Within approximately

6 m (20 feet)

Remote control

sensor

01RX-V495-e/f-6 6/22/99, 1:33 PM52

English

SETUP CODES

To control your components

(MD recorder, DVD player,

TV, etc.)

1. Turn on the component to be used.

2. Press the component selector which

matches the component to be

controlled (TAPE/MD, DVD/LD, TV

etc.).

3. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

4. Use the numeric buttons to enter the

four-digit manufacturer’s code for

the component to be used. Make

sure that the indicator flashes twice.

If the indicator does not flash, repeat

step 3 and re-enter the code.

5. Press POWER (or any other button)

on the remote control transmitter to

check if you have preset the code

correctly. If the component cannot

be controlled by the remote control

transmitter, try entering another

code for the same manufacturer.

Returning to the factory-set

codes

To return all components to the factory-

set codes, follow these steps.

1. Press a button on the component

selector other than AMP<TUNER>.

2. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

3. Enter the code number “9990”.

4. Make sure that the indicator flashes

twice.

To return each component to the factory-

set codes, follow these steps.

1. Press the component selector which

matches the component to be

returned to the factory-set codes.

2. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

3. Enter the code number “0000”.

4. Make sure that the indicator flashes

twice.

The following codes are preset by the

factory.

Factory-set codes

Component

Component Code

selector

TV TV 0101

CBL/DBS DBS tuner 0006

VCR VCR 0002

DVD/LD DVD player

0008 YAMAHA

CD CD player

0005 YAMAHA

TAPE/MD Tape deck

0004 YAMAHA

We recommend that you write all code

numbers you have preset on the “Quick

Reference Card”.

Presetting the remote control transmitter

Perform the presetting procedure for each component you want to control with the remote control transmitter.

Note: If your component does not respond to any of the codes listed for the manufacturer, use the original remote control

transmitter that was supplied with the component.

To use a second (and third) VCR

You can control a second (and/or third)

VCR in the CBL/DBS and DVD MENU

modes if a CBL (or DBS) or DVD player

is not being used.

If you want to control a second (and/or

third) VCR in the DVD MENU mode, you

must preset the code for an LD player in

that mode.

1. Turn on the VCR to be used.

2. Press CBL/DBS or DVD MENU on

the component selector.

3. Press both VOLUME buttons (

) for about four seconds at the

same time so that the indicator

flashes twice.

4. Use the numeric buttons to enter the

four-digit code for the second (or

third) VCR. Make sure that the

indicator flashes twice. If the

indicator does not flash, repeat step

3 and re-enter the code.

5. Press POWER (or any other button)

on the remote control transmitter to

check if you have preset the code

correctly. If the VCR cannot be

controlled by the remote control

transmitter, try entering another

code for the same manufacturer.

01RX-V495-e/f-6 6/22/99, 1:33 PM53

SYMPTOM

The unit fails to turn on when

STANDBY/ON is pressed, or set in

the standby mode suddenly soon

after the power has been turned on.

The unit does not work normally.

No sound or no picture.

The sound suddenly goes off.

Only one side speaker outputs

sound.

A “humming” sound can be heard.

The volume level is low while

playing a record.

The volume level cannot be

increased, or the sound is distorted.

No sound from the effect speakers.

No sound from the rear speakers.

CAUSE

The power cord is not plugged in or the

plug is not completely inserted.

The IMPEDANCE SELECTOR switch

on the rear panel is not fully set at the

upper or lower end.

The internal microcomputer has been

frozen by an external electric shock

(lightning, excessive static electricity,

etc.) or by a power supply with low

voltage.

Incorrect output cord connections.

Appropriate program source has not

been selected.

SPEAKERS have not been set

properly.

The speaker connections are not

secure.

The protection circuit has been

activated because of a short circuit, etc.

The SLEEP timer has functioned.

Incorrect setting of BALANCE.

Incorrect cord connections.

No connection from the turntable to the

GND terminal.

The record is being played on a

turntable with an MC cartridge.

The component connected to the REC

OUT terminals of this unit is in the

standby mode.

The sound effect is set off.

A Dolby Surround decoding program is

being used with material not encoded

with Dolby Surround.

The sound output level of the rear

speakers is set to minimum.

A monaural sound source is being

played in the DOLBY PRO LOGIC or

DOLBY PRO LOGIC ENHANCED

program.

REMEDY

Firmly plug in the power cord.

Slide the switch fully to the upper or

lower end.

Set the unit in the standby mode and

disconnect the AC power cord from the

AC outlet. After about 30 seconds have

passed, connect the power cord and

operate the unit again.

Connect the cords properly. If the

problem persists, the cords may be

defective.

Select an appropriate program source

by INPUT.

Set SPEAKERS corresponding to the

speakers in use to the ON position.

Secure the connections.

Set the unit in the standby mode and

then switch on again to reset the

protection circuit.

Cancel the SLEEP timer.

Adjust it to the appropriate position.

Connect the cords properly. If the

problem persists, the cords may be

defective.

Firmly connect the audio plugs. If the

problem persists, the cords may be

defective.

Make the GND connection between the

turntable and this unit.

The turntable should be connected to

the unit through the MC head amplifier.

Turn on the power to the component.

Press EFFECT to turn it on.

Use a different sound field program.

Raise the sound output level of the rear

speakers.

Select another sound field program

suitable for the monaural sound source.

Amplifier

TROUBLESHOOTING

If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple

measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and

contact your authorized YAMAHA dealer or service center for help.

01RX-V495-e/f-7 6/22/99, 1:34 PM54

English

SYMPTOM

No sound from the center speaker.

The sound field cannot be recorded.

The DVD/LD, TV or DBS source

cannot be recorded on a tape deck,

MD recorder or VCR connected to

this unit.

FM stereo reception is noisy.

There is distortion and clear

reception cannot be obtained even

with a good FM antenna.

The desired station cannot be tuned

in with the automatic tuning method.

Previously preset stations can no

longer be tuned in.

The desired station cannot be tuned

in with the automatic tuning method.

There are continuous crackling and

hissing noises.

There are buzzing and whining

noises (especially in the evening).

Although you do the operations to

recall a preset station, the station

cannot be tuned in, or a station other

than the preset one is tuned in.

The remote control transmitter does

not work.

CAUSE

The input signals of the source encoded

with Dolby Digital do not have center

channel signals.

The sound output level of the center

speaker is set to minimum.

The function “CNTR” in the SET MENU

is set to the NONE position.

Incorrect sound field program selection.

It is not possible to record the sound

field on a tape deck or MD recorder

connected to the unit’s REC OUT

terminals.

The DVD/LD player, TV or DBS tuner is

connected to the unit by only the digital

terminals.

The characteristics of FM stereo

broadcasts may cause this problem

when the transmitter is too far away or

the antenna input is poor.

There is multipath interference.

The station is too weak.

This unit has been unplugged for a long

period.

The signal is weak or antenna

connections are loose.

Noise will result from lightning,

fluorescent lamps, motors, thermostats

and other electrical equipment.

A television set is being used nearby.

Some of the preset station data has

been modified because the setting of

the FREQUENCY STEP switch was

changed after storing the station data.

Direct sunlight or lighting (from an

inverter type of fluorescent lamp, etc.) is

striking the remote control sensor of the

this unit.

The manufacturer’s code has not been

set properly.

The proper manufacturer’s code for the

component to be controlled has not

been set.

The component to be controlled has not

been selected.

REMEDY

Refer to the instruction for the source

being currently played.

Raise the sound output level of the

center speaker.

Select the LARGE or SMALL position.

Select the appropriate program.

Make additional connections between

the analog terminals.

Check the antenna connections.

Try using a high-quality directional FM

antenna.

Set TUNING MODE to the manual

tuning mode.

Adjust antenna position to eliminate

multipath interference.

Use the manual tuning method.

Use a high-quality directional FM

antenna.

Repeat the presetting procedure.

Tighten the AM loop antenna

connections and rotate it for best

reception.

Use the manual tuning method.

Use an outdoor antenna and a ground

wire. This will help somewhat, but it is

difficult to eliminate all noise.

Relocate this unit away from the TV.

Preset the stations again by following

the preset tuning procedure.

Change the position of the unit.

Set the code again.

Try entering another code for the same

manufacturer.

Press the component selector which

matches the component to be

controlled.

Remote control transmitter

Amplifier

FM/AM

01RX-V495-e/f-7 6/22/99, 1:34 PM55

SYMPTOM

The sound is degraded when

listening with the headphones to a

CD player or tape deck that is

connected to this unit.

There is noise interference from

digital or high-frequency equipment

or the unit.

CAUSE

The unit is in the standby mode.

The unit is too close to the digital or

high-frequency equipment.

REMEDY

Turn on the power to the unit.

Move the unit further away from those

equipment.

Others

01RX-V495-e/f-7 6/22/99, 1:34 PM56

English

AUDIO SECTION

Minimum RMS Output Power

8 ohms, 20 Hz to 20 kHz, 0.04% THD

MAIN L/R ........................... 60 W + 60 W

CENTER......................................... 60 W

REAR L/R.......................... 60 W + 60 W

8 ohms, 1 kHz, 0.07% THD

MAIN L/R ........................... 70 W + 70 W

CENTER......................................... 70 W

REAR L/R.......................... 70 W + 70 W

Maximum Power

[China and General models only]

8 ohms, 1 kHz, 10% THD

MAIN L/R ............................. 95 W + 95 W

CENTER ........................................... 95 W

REAR L/R ............................ 95 W + 95 W

Dynamic Power per Channel

(by IHF Dynamic Headroom measuring method)

MAIN L/R

8/6/4/2 ohms ................ 80/100/120/145 W

Dynamic Headroom (8 ohms)

[U.S.A. and Canada models only]

...................................................... 1.55 dB

Power Band Width

8 ohms, 30 W, 0.1% THD

.........................................10 Hz to 50 kHz

Damping Factor

MAIN L/R

8 ohms, 20 Hz to 20 kHz.......... 60 or more

Input Sensitivity/Impedance

PHONO MM ................... 2.5 mV/47 k-ohms

CD/TAPE·MD/DVD·LD/TV·DBS/VCR/

VIDEO AUX ................... 150 mV/47 k-ohms

EXT. DECODER

MAIN L/R .................... 150 mV/47 k-ohms

CENTER/SURROUND L/R/SUBWOOFER

.................................... 150 mV/40 k-ohms

Maximum Input Signal

PHONO MM

1 kHz, 0.1% THD .............100 mV or more

CD/TAPE·MD/DVD·LD/TV·DBS/VCR/

VIDEO AUX (EFFECT ON)

1 kHz, 0.5% THD .................2.2 V or more

Output Level/Impedance

REC OUT ..................... 150 mV/1.2 k-ohms

SUBWOOFER

(MAIN SP: SMALL) ........ 4.0 V/1.2 k-ohms

Headphones Jack Rated Output/Impedance

CD/TAPE·MD/DVD·LD/TV·DBS/VCR/

VIDEO AUX input,

1 kHz, 150 mV, 8 ohms ...... 0.4 V/390 ohms

Frequency Response (20 Hz to 20 kHz)

CD/TAPE·MD/DVD·LD/TV·DBS/VCR/

VIDEO AUX to MAIN L/R SP OUT

.................................................... 0±0.5 dB

RIAA Equalization Deviation

PHONO MM .................................. 0±0.5 dB

Total Harmonic Distortion (20 Hz to 20 kHz)

PHONO MM to REC OUT

1 V........................................0.02% or less

CD/TAPE·MD/DVD·LD/TV·DBS/VCR/

VIDEO AUX (EFFECT OFF) to MAIN SP

OUT

30 W/8 ohms......................0.025% or less

Signal-to-Noise Ratio (IHF-A Network)

PHONO MM to REC OUT

[U.S.A., Canada, China and General

models]

(5 mV, Input Shorted) ..........86 dB or more

[Australia and Singapore models]

(5 mV, Input Shorted) ..........81 dB or more

CD/TAPE·MD/DVD·LD/TV·DBS/VCR/

VIDEO AUX (EFFECT OFF) to MAIN SP

OUT

(150 mV, Input Shorted) ......96 dB or more

Residual Noise (IHF-A Network)

MAIN L/R SP OUT................ 150 µV or less

Channel Separation

(Vol. –30 dB, EFFECT OFF)

PHONO MM

(Input Shorted, 1 kHz/10 kHz)

....................60 dB or more/55 dB or more

CD/TAPE·MD/DVD·LD/TV·DBS/VCR/

VIDEO AUX

(Input 5.1 k-ohms Terminated, 1 kHz/10 kHz)

....................60 dB or more/45 dB or more

Tone Control Characteristics

BASS: Boost/cut ............. ±10 dB (50 Hz)

Turnover Frequency......... 350 Hz

TREBLE: Boost/cut ........... ±10 dB (20 kHz)

Turnover Frequency........ 3.5 kHz

Filter Characteristics

MAIN L/R, REAR L/R (SPEAKER: SMALL)

(H.P.F) ..................... fc = 90 Hz, 12 dB/oct.

SUBWOOFER

(L.P.F) ..................... fc = 90 Hz, 18 dB/oct.

VIDEO SECTION

Video Signal Type

[U.S.A. and Canada models] ..............NTSC

[Australia and Singapore models] ......... PAL

[China and General models]....... NTSC/PAL

Video Signal Level ................ 1 Vp-p/75 ohms

Maximum Input Level .......... 1.5 Vp-p or more

Signal-to-Noise Ratio ...............50 dB or more

Monitor Output Frequency Response

.............................. 5 Hz to 10 MHz, –3 dB

FM SECTION

Tuning Range

[U.S.A. and Canada models]

..................................... 87.5 to 107.9 MHz

[Australia and Singapore models]

................................. 87.50 to 108.00 MHz

[China and General models]

100 kHz step ................ 87.5 to 108.0 MHz

50 kHz step .............. 87.50 to 108.00 MHz

50 dB Quieting Sensitivity (IHF)

(100% mod., 1 kHz)

Mono................................. 1.6 µV (15.3 dBf)

Stereo ................................ 23 µV (38.5 dBf)

Usable Sensitivity (DIN)

[Australia and Singapore models only]

Mono (S/N 26 dB) ........................... 0.9 µV

Stereo (S/N 46 dB)........................... 28 µV

Alternate Channel Selectivity (±400 kHz)

[U.S.A., Canada, China and General

models only] ....................................... 75 dB

Selectivity

(two signals, 40 kHz Dev. ±300 kHz)

[Australia and Singapore models only]

......................................................... 55 dB

SPECIFICATIONS

01RX-V495-e/f-7 6/22/99, 1:34 PM57

Signal-to-Noise Ratio

(IHF) Mono/Stereo

[U.S.A., Canada, China and General

models] ..................................81 dB/75 dB

(DIN-Weighted, 40 kHz Dev.) Mono/Stereo

[Australia and Singapore models]

...............................................75 dB/69 dB

Harmonic Distortion (1 kHz)

Mono/Stereo ............................... 0.1%/0.2%

Stereo Separation (1 kHz) .................... 48 dB

Frequency Response

20 Hz to 15 kHz ................................ 0±1 dB

Antenna Input.............. 75 ohms, Unbalanced

Output Level

[U.S.A., Canada, China and General

models]

(100% mod., 1 kHz) ...................... 550 mV

[Australia and Singapore models]

(40 kHz Dev., 1 kHz)] .................... 550 mV

AM SECTION

Tuning Range

[U.S.A. and Canada models]

....................................... 530 to 1,710 kHz

[Australia and Singapore models]

....................................... 531 to 1,611 kHz

[China and General models]

10 kHz step .................... 530 to 1,710 kHz

9 kHz step ...................... 531 to 1,611 kHz

Usable Sensitivity............................ 300 µV/m

Signal-to-Noise Ratio ............................ 52 dB

Antenna.................................... Loop antenna

Output Level

(30% mod., 1 kHz) ........................ 150 mV

GENERAL

Power Supply

[U.S.A. and Canada models]

........................................ AC 120 V, 60 Hz

[Australia model]................ AC 240 V, 50 Hz

[General model]

.............. AC 110/120/220/240 V, 50/60 Hz

[China model] .................... AC 220 V, 50 Hz

[Singapore model] ............. AC 230 V, 50 Hz

Power Consumption

[U.S.A., Australia, Singapore, China and

General models] ................................ 230 W

[Canada model] .................... 260 W/340 VA

Maximum Power Consumption

5 ch, 10% THD

[General model only] ......................... 630 W

AC Outlets

2 SWITCHED OUTLETS

[U.S.A., Canada, Singapore, China and

General models]............. 100 W max. total

1 SWITCHED OUTLET

[Australia model] .................... 100 W max.

Dimensions (W x H x D)

..................................435 x 151 x 391 mm

(17-1/8” x 5-15/16” x 15-3/8”)

Weight

.............................. 11.2 kg (24 lbs. 11 oz.)

Accessories......................... AM loop antenna

Indoor FM antenna

Remote control transmitter

Batteries

Antenna adapter

(U.S.A. and Canada models only)

Specifications are subject to change without

notice.

01RX-V495-e/f-7 6/22/99, 1:34 PM58

113

A-Mark 1161

A Tandy 0941

Abex 1151

Admira 1141

Adventura 1131

Aiko 1121

Akai 0331, 1101, 1111

Alba 0431

Alleron 1091

Ambassador 1081

Amstrad 0481, 1081

Anam 0251, 1041, 1051, 1061, 1071

Anam National 1041

AOC 0361, 1021, 1031, 1111, 1161

Archer 1161

Audiosonic 1001

Audiovox 1051, 1161

Awai 1481

Bauer 0441

Baur 1001

Beijing 1511, 1551, 1561

Belcor 1031

Bell & Howell 0981, 0991

Beon 1001

Bradford 1051

Brockwood 1031

Broksonic 1161

Bush 1001

Candle 0351, 0361, 0961,

0971, 1111, 1131

Capehart 1021

Carver 0101

Cathay 1001

Celebrity 0951

Centurion 0411

Changhong 1541, 1551, 1561, 1621

Citizen 0351, 0361, 0921, 0931,

0941, 0961, 0971, 1111,

1121, 1131

Clairtone 1011

Clarivox 1001

Concerto 0351, 0971

Conrowa 1751

Contec 0901, 0911, 1011, 1051

Corando 0941

Craig 0251, 1051

Crown 0941, 1051

Curtis Mathes 0161, 0361, 0931,

0941, 0981, 1111

CXC 1051

Daewoo 0291, 0301, 0331, 0721,

0941, 1001, 1031, 1121,

1191, 1531, 1581,

1591, 1601

Dansai 1001

Daytron 0941, 1031

Decca 0271, 1001

Dixi 0331, 1001, 1071

Dumont 0891, 1031

Dynatech 0881

Electroband 0951, 1011

Electrohome 0941

Electron 0941

Elin 1001

Elta 0331

Emerson 0001, 0021, 0061, 0071,

0081, 0091, 0111, 0811,

0821, 0831, 0841, 0851,

0861, 0871, 0901, 0921,

0941, 0981, 1011, 1031,

1051, 1081, 1091

Envision 0361, 1111

Erres 1001

Etron 0331

Ferguson 1001

Finlux 1001

Fisher 0171, 0801, 0981

Formenti 0441

Formonti 1001

Fortress 1141

Fujitsu 1091

Funai 1051, 1091, 1341, 1361,

1411, 1451, 1501, 1521

Futuretech 1051

GE 0131, 0161, 0201, 0751,

0761, 0771, 0781, 0791,

0811, 0861, 1041

GEC 0271, 1001

Gemini 0391

Genexxa 0431

Gibralter 0891, 1031, 1111

GoldStar 0031, 0121, 0351, 0411,

0731, 0741, 0861, 0941,

0971, 1001, 1031,

1111, 1151

Goodmans/Tashiko 0271, 0661, 1001

Granada 1001

Grundig 1781, 1791, 1801, 1811,

1821, 1831, 1841, 1851,

1861, 1871, 1881

Gunpy 1051, 1091

H/K 0721

Hallmark 0861

Hanseatic 1001

Harvard 1051, 1061

Hinari 1001, 1091

Hitachi 0181, 0351, 0671, 0681,

0691, 0701, 0711, 0871,

0941, 0971, 1351

Hypson 1001

Ima 1051

Indiana 1001

Infinity Reference 0101

Interfunk 1001

ITT 0611

Janeil 1131

JBL 0101

JCB 0951

Jensen 0311

Jinxing 1531, 1541, 1551, 1561,

1571, 1621, 1631, 1641,

1651, 1691, 1731

JVC 0261, 0281, 0641,

0651, 0661, 0841

Kawasho 0901

Kaypani 1021

Kenwood 0361, 1031, 1111

Kloss 0631, 0721, 1131

KTV 0921, 0941, 1011, 1051, 1111

Leyco 1001

Liesenk & Tter 1001

Lloytron 0941

Loewe 1001

Logik 0991, 1771

Luxman 0351, 0971

Lxi 0101, 0621, 0761, 0861, 0981

Magnavox 0101, 0341, 0391, 0401,

0411, 0421, 0581, 0591,

0601, 0611, 0631,

0661, 0961, 1111

Majestic 0991

Marantz 0101, 0221, 0361, 1001, 1111

Mark 1001

Matsui 0271, 0331, 1001

Mediator 1001

Megatron 0691, 0861, 1161

MEI 1011

M Electronic 1001

Memorex 0331, 0571, 0861, 0971,

0981, 0991, 1771

Metz 1791, 1831, 1891, 1901,

1911, 1921, 1931, 1941

MGA 0361, 0561, 0571,

0861, 1031, 1111

Midland 0751, 0761, 0891, 0941, 1151

Mitsubishi 0221, 0321, 0561,

0571, 0661, 0861,

1031, 1101, 1381

Montgomery 1091

Motorola 1041, 1141

MTC 0351, 0361, 0881, 0931,

0971, 1011, 1031, 1111

Multitech 0881, 1051

NAD 0551, 0621, 0861

NEC 0241, 0351, 0361, 0661, 0971,

1031, 1111, 1321, 1711

LIST OF MANUFACTURER’S CODES

LISTES DES CODES FABRICANT

02RX-V495-CODE(E/F) 6/22/99, 1:35 PM113

114

Neckermann 1001

Nei 1001

Nikkai 0271, 0431, 1001, 1151

Nikko 0861, 1111, 1121

Novabeam 0721

NTC 1121

Onwa 1051

Optimus 0551

Optonica 0541, 1141

Orion 0831, 1001

Osaki 0271, 1151

Otto Versand 1001

Panasonic 0101, 0191, 0251, 0751,

1041, 1311, 1371, 1431

Panda 1541, 1721

Penny 0161, 0361, 0521, 0531, 0621,

0731, 0751, 0761, 0781, 0791,

0861, 0931, 0941, 1031, 1041,

1111, 1151, 1161

Peony 1561, 1621

Philco 0361, 0581, 0591, 0601, 0611,

0631, 0961, 1031, 1111

Philips 0101, 0401, 1001

Phonola 1001

Pilot 0941, 1031, 1111

Pioneer 0511, 0551, 0871, 1331

Portland 0941, 1031, 1121

Priceclub 0931

Prism 0751

Proscan 0761

Protech 1001

Proton 0501, 0861, 0941, 1021, 1161

Pulsar 0891

Pulser 1031

Quasar 0251, 0751, 1041

Quelle 1001

Radio Shack 0541, 0941, 1031,

1051, 1151

Radiola 1001

RCA 0051, 0141, 0151, 0181,

0411, 0491, 0531, 0761,

0771, 0871, 1031

Realistic 0541, 0861, 0941, 0971,

0981, 1031, 1051,

1111, 1151

Rhapsody 1011

R-line 1001

Runco 0891, 1111

Saisho 0331, 1081

Sampo 0361, 0941, 1021, 1111, 1151

Samsung 0331, 0341, 0351, 0361,

0861, 0931, 0941, 0971,

1001, 1031, 1111,

1151, 1461

Samsux 0941

Sanyo 0171, 0231, 0271, 0661, 0801,

0911, 0981, 1231, 1251, 1261

SBR 1001

Schneider 1001

Scimitsu 1031

Scotch 0861

Scott 0831, 0861, 0941,

1031, 1051, 1091

Sears 0101, 0161, 0171, 0351, 0481,

0521, 0621, 0761, 0801, 0861,

0971, 0981, 1091

Shanghai 1561, 1681

Sharp 0461, 0471, 0541, 0661, 0911,

0941, 1141, 1241, 1271

Shogun 1031

Signature 0991, 1771

Simpson 0581, 0961

Solavox 1151

Sonoko 1001

Sontec 1001

Sony 0371, 0451, 0661, 0841,

0951, 1281, 1441

Soundesign 0861, 0961, 1051, 1091

Soundwave 1001

Spectricon 1161

Squareview 0481

SSS 1031, 1051

Star-lite 1051

Suprem 0951

Supre-macy 1131

Surpa 0351, 0971

Sylvania 0101, 0361, 0441, 0581,

0591, 0601, 0611, 0631,

0961, 1111

Symphonic 0481

Sysline 1001

Tandy 0271, 0431, 1141

Tatung 0271, 0881, 1001, 1041, 1161

Tcl 1561, 1631, 1701

Technics 0751

Techwood 0351, 0751, 0971

Teknika 0101, 0351, 0571, 0931, 0941,

0961, 0971, 0991, 1031,1051,

1091, 1121, 1131, 1771

Teletech 0331

Tera 0501

Thakral 1671

Thorm 1001

TMK 0351, 0861, 0971, 1081

Toshiba 0381, 0521, 0621, 0661,

0931, 0981, 1301

Tosonic 1011

Totevision 0941

Trical 0911

Universal 0781, 0791

Universum 1001

Vector Research 0361, 1111

Vestel 1001

Victor 0651, 1201, 1211, 1221

Video Concept 1101

Vidikron 0101, 0211

Vidtech 0861, 1031

Viking 1131

Wards 0101, 0361, 0451, 0541, 0581,

0591, 0601, 0611, 0771, 0781,

0791, 0861, 0971, 0991, 1031,

1091, 1111, 1771

Watson 1001

Xogego 1611, 1621, 1661, 1741, 1761

Yamaha 0221, 0361, 0571, 1031,

1111, 1141, 1381

Yoko 1001

Zenith 0011, 0041, 0891, 0991, 1771

Zonda 1161

CABLE

ABC 0256, 0376

Antronix 0136

Archer 0136, 0286

BBT 0076

Cabletime 0166

Cablevision 0196

Colour Voice 0306, 0346

Comtronics 0216, 0276

Eagle Comronics 0276

Eastern 0066

Electricord 0206

Electus 0266

GE 0116, 0126

GEC Cable System 0196

Hamlin H5 0676

Hamlin H6 0666

Hamlin H6S 0656

Hamlin H8 0646

Hamlin H9 0636

Jerrold 0256

Jerrold 400L 0626

Jerrold 450L 0616

Jerrold 550 0606

Jerrold Osd Catv 0596

Jerrold Sprucer 0436

Magnavox/Philips 0416, 0426

Mamm 0296

Memorex 0386

Movie Time 0146, 0206

Northcoast 0016

NSC 0146

Oak 0106

Oak Sigma 450 0546

Oak Sigma 550 0536

Panasonic TZ 120/130 0476

Panasonic TZ 170/180 0446

Panasonic TZ140 0466

Panasonic TZ150/160 0456

Paragon 0386

02RX-V495-CODE(E/F) 6/22/99, 1:35 PM114

115

Philips 0036, 0216, 0306, 0316,

0326, 0336, 0346

Pioneer 0006, 0086

Pioneer BR50 0846

Pioneer BR60/70/80/81/82 0696

Pioneer BR90 0556

Pulsar 0386

RCA Digital Satellite System 0396, 0406

Realistic 0136

Regency/Eastern 0686

Runco 0386

Samsung 0276

Scientific Atlanta 175/475 0576

Scientific Atlanta 75 0366, 0586

Scientific Atlanta 8650 0566

Signal 0276

SL Marx 0276

Spectavision 0236

Standard Components 0186

Starcom V 0256

Stargate 0276

Sylvania/Texscan 0376, 0496

Teknika 0176

Teleservice 0056

Teleview 0276

Texscan 0186, 0376

TFC 0026

Tocom 0226, 0356

Tocom 5503A 0526

Tocom 5503VIP/5507 0516

Tocom TC56 0506

Toshiba 0386

Tudi 0046

Unika 0136

Universal 0136, 0156, 0206, 0286

Videoway 0096

Viewstar 0216

Zenith 0246, 0386, 0486

DBS TUNER

Alpha Star 0826

Chaparral 0756

Echostar 0836

General Instrument 0776

HTS 0836

Hughes Network Systems 0816

Jerrold 0776, 0786

Panasonic 0806

Primestar 0776, 0786

RCA 0766

Sony 0796

VCR

A Tandy 0902

Adventura 0992

Aiko 0982

Aiwa 0992

Akai 0262, 0942, 0952, 0962, 0972

American High 0932

Amstrad 0992

ASA 0002, 0912

Asha 0922

Audio Dynamics 0202

Audiovox 0912

Beaumark 0922

Bell & Howell 0902

Blaupunkt 0412

Broksonic 0872, 0882, 0892

Bush 0852

Calix 0912

Canon 0862, 0932

CCE 0852, 0982

Citizen 0912, 0982

Colt 0852

Craig 0832, 0842, 0852, 0912, 0922

Curtis Mathes 0662, 0822, 0932

Cybernex 0922

Daewoo 0802, 0812, 0982

DBX 0202

Dynatech 0472, 0992

Electrohome 0912

Electrophonic 0912

Emerex 0792

Emerson 0072, 0132, 0142, 0152,

0162, 0172, 0182, 0192,

0212, 0702, 0712, 0722,

0732, 0742, 0752, 0762,

0772, 0782, 0872, 0882,

0892, 0912, 0952,

0992, 1072

Finlux 0002, 0992

Fisher 0682, 0692, 0842, 0902

Fuji 0672, 0932

Funai 0992

Garrard 0992

GE 0662, 0822, 0932

Go Video 0642, 0652

GoldStar 0082, 0632, 0912

Goodmans 0402

Gradiente 0992

Granda 0612, 0902

Grundig 0002

H/K 1082

Harley Davidson 0992

Harmon/Kardon 0632, 1082

Harwood 0752, 0852

Headquarter 0612

HI-Q 0842

Hinari 0852

Hitachi 0102, 0562, 0572, 0582,

0592, 0602, 0992

ITT 0942

JVC 0202, 0522, 0532, 0542, 0552

Kenwood 0202, 0542, 0612,

0632, 0902

KLH 0852

Kodak 0912, 0932

Lloyd 0992

Logik 0852

Luxor 0942

LXI 0022, 0912

Magnavox 0002, 0482, 0492,

0502, 0512, 0932

Magnin 0922

Marantz 0002, 0202, 0402, 0632, 0932

Marta 0912

Matsui 0722

Matsushita 0932

MEI 0222, 0932

Memorex 0232, 0242, 0472, 0512,

0612, 0842, 0902, 0912,

0922, 0932, 0992

MGA 0762, 0952

MGA Technology 0922

Minolta 0592, 0602

Mitsubishi 0452, 0462, 0542,

0762, 0952, 1082

Motorola 0472, 0932

MTC 0922, 0992

Multitech 0852, 0992

NAD 0442

NEC 0122, 0202, 0292, 0422,

0432, 0542, 0632

Nikko 0912

Noblex 0922

Olympus 0412, 0932

Optimus 0442, 0472, 0912

Optonica 0402

Orion 0212, 0722, 0742, 0772

Osaki 0912

Panasonic 0012, 0052, 0092,

0222, 0372, 0382,

0392, 0412, 0932

Penny 0202, 0432, 0602, 0632,

0692, 0912, 0922, 0932

Pentax 0592, 0602

Perdio 0992

Philco 0002, 0932

Philips 0002, 0282, 0402, 0492, 0932

Pilot 0912

Pioneer 0442, 0542

Proscan 1002, 1012, 1022, 1032,

1042, 1052, 1062

Pulsar 0512

Quarter 0612

02RX-V495-CODE(E/F) 6/22/99, 1:35 PM115

116

Quartz 0272, 0612

Quasar 0382, 0392, 0932

Radio Shack 0912, 0992

Radix 0912

Randex 0912

RCA 0112, 0382, 0392, 0482, 0592,

0602, 0662, 0822, 0942

Realistic 0402, 0472, 0612, 0682,

0842, 0902, 0912,

0922, 0932, 0992

Ricoh 0352, 0362

Saisho 0212, 0582, 0722,

0732, 0742, 0772

Salora 0612, 0762

Samsung 0212, 0312, 0922, 0962

Sanky 0472, 0512

Sansui 0292, 0542, 0832

Sanyo 0242, 0612, 0842, 0902, 0922

SBR 0002, 0282

Schneider 0852

Scott 0342, 0712, 0762,

0872, 0882, 0892

Sears 0302, 0592, 0602, 0612,

0682, 0692, 0842,

0902, 0912, 0932

Sharp 0402, 0472

Shintom 0852

Shogun 0922

Singer 0852

Sony 0032, 0332, 0352, 0362,

0672, 0792, 0932

STS 0602

Sunpak 0352

Sylvania 0002, 0492, 0502,

0762, 0932, 0992

Symphonic 0992

Tandy 0992

Tashiko 0712, 0992

Teac 0992

Technics 0932

Teknika 0322, 0912, 0932, 0992

Telefunken 0252

TMK 0212, 0732, 0772, 0922

Toshiba 0062, 0302, 0342, 0622,

0682, 0712, 0762

Totevision 0912, 0922

Unitech 0922

Vector Research 0202, 0432, 0632

Victor 0532, 0542, 0552

Video Concepts 0202, 0432,

0632, 0952

Wards 0322, 0402, 0472, 0482,

0602, 0712, 0842, 0852,

0922, 0932, 0992

Yamaha 0202, 0632, 0762

Zenith 0042, 0362, 0512, 0672

DVD PLAYER

Akai 0108

JVC 0168

Onkyo 0128

Panasonic 0048

Philips 0188

Pioneer 0208, 0228

Samsung 0148

Sharp 0068

Sony 0028

Toshiba 0088

Yamaha 0008, 0048

LD PLAYER

Aiwa 0157

Denon 0147

Disco Vision 0017

Funai 0157

Hitachi (E) 0017

Kenwood 0087, 0107

Magnavox 0027

Marantz 0027

Mitsubishi 0137

NAD 0137

Panasonic 0077, 0177

Philips 0027

Pioneer 0037, 0017, 0137

RCA 0167

Realistic 0157

Sharp 0127

Sony 0047, 0057, 0117

Victor 0097

Yamaha 0007, 0067

CD PLAYER

Acoustic Research 1295

ADC 0025, 0065

Adcom 0205, 0255, 1015

ADS 0265

Aiwa 0295, 0945, 1035, 1055

Akai 0175, 0485, 0535

Alpine 1215, 1305

Audio-Technica 0545

BSR 0245, 0655, 0775

California Audio Lab 0055

Capetronic 1205

Carrera 0245

Carver 0285, 1135

Casio 0345

Crown 0185

Curtis Maths 0345

Denon 0275, 0875, 0885

Deual (E) 0505

Dynamic Bass (H) 0555

Emerson 0205, 0325, 1105

Eroica 1275

Fisher 0095, 0555, 0925, 1005

Garrard 0365

Genexxa 0305, 0325, 1105

GoldStar 1225, 1265, 1135, 1335

H/K 0105, 0175, 0465, 0995

Hitachi 0195, 0505, 0205, 0815

Inkel 0115, 0395

JVC 0315

Kenwood 0045, 0095, 0405,

0585, 0725, 0735,

0745, 0755, 0895

Kyocera 0025

Luxman 0075, 0425, 0675,

0705, 0715, 0985

Magnavox 0165, 0215, 0645, 0955

Marantz 0215, 0235, 0375, 0785, 1345

McIntosh 0355, 1085

MCS 0905, 1315

Memorex 0205, 0225, 0235,

0305, 0325, 1105

MGA 0135

Mission 0215

Mitsubishi 0135, 0445

MTC 1255

NAD 0035, 0615, 0685, 0695

Nakamichi 0125, 0435, 0515

NEC 0255, 0905, 0965

Nikko 0545, 1005

Onkyo 0155, 0455, 0495, 0805, 1155

Optimus 0225, 0245, 0555, 0595,

0845, 0855, 0865,

0895, 0935

Panasonic 0055, 0825, 1095, 1125

Penny 0905

Philips 0165, 0215

Pioneer 0305, 0935, 1045

Proton 0215, 1185

Quasar 0055

RCA 0205, 0915, 1115

Realistic 0205, 0225, 0235,

0325, 0555, 0845

Revox 1175

Rotel 0215

Saba Telecommander (E) 0505

SAE 0215

Samsung 1285

Sansui 0215, 0625, 0975, 1025, 1105

Sanyo 0145, 0555, 0635, 0765

Scott 0325, 1105

Sears 0345

Sharp 0235, 0665, 0895, 1065, 1075

Sherwood 0115, 0235, 0395, 0475

Siements Garrard 1245

Signature 0175

Sontec 1165

02RX-V495-CODE(E/F) 6/22/99, 1:35 PM116

117

Sony 0065, 0565, 0865, 1145

Staron 1235

STS 0025

Sylvania 0215

Symphnoic 0335

Tandy 0305

Tangberg 1195

Teac 0235, 0335, 0385, 0525,

0795, 0835, 1355

Technics 0055, 0605, 1095

Techwood 1325

Telefunken (E) 0505

Thomson (E) 0505

Toshiba 0035, 0685

Vector Research 0065, 1135

Victor 0315

Wards 0175

Yamaha 0005, 0015, 0575, 1065

MD RECORDER

Yamaha 0024

TAPE DECK

Aiwa 0094, 0214, 0224

Akai 0184

Carver 0094

Denon 0304

Fisher 0144

Garrard 0194, 0204

JVC 0274, 0284, 0294

Kenwood 0124, 0134, 0154,

0234, 0244, 0264

Magnavox 0094

Marantz 0094, 0344

Mitsubishi 0184

Onkyo 0364, 0374

Optimus 0034, 0064, 0204, 0334

Philips 0094

Pioneer 0034, 0044, 0064

Revox 0354

Sansui 0094, 0344

Sharp 0264

Sherwood 0334

Sony 0054, 0084, 0324

Teac 0194, 0254

Technics 0074, 0314

Victor 0294

Wards 0034

Yamaha 0004, 0014

02RX-V495-CODE(E/F) 6/22/99, 1:35 PM117

Printed in Malaysia ID

V342050

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

RX-V4 95

Natural Sound AV Receiver

Ampli-Tuner Audio-Video

OWNER’S MANUAL

MODE D’EMPLOI

U C A

01RX-V495-e/f cv1/4 6/22/99, 2:40 PM1

Quick Reference Card

AMP<TUNER>

TAPE/MD CD DVD/LD

POWER

Input selector Input selector Input selector Input selector

A/B/C/D/E &

PRESET +/–

TEST

VOLUME

MUTE

SLEEP

+/–

TIME/LEVEL

EFFECT

TV VOLUME

PRG+/PRG–

TV INPUT

POWER

VOLUME VOLUME

MUTE MUTE

SLEEP SLEEP SLEEP

SKIP–

REC/PAUSE

PLAY

DIR A (TAPE)

SKIP– (MD)

REWIND (TAPE)

SEARCH (MD)

TV VOLUME

EFFECT

DISC SKIP +/–

EFFECT

DISC SKIP +/–

DISPLAY (MD)

PAUSE (MD)

DECK A/B (TAPE)

DIR B (TAPE)

SKIP+ (MD)

STOP

FAST

FORWARD (TAPE)

SEARCH (MD)

POWER

MUTE

STOP

SKIP–

DISPLAY

PAUSE

SKIP+

PLAY

POWER

VOLUME

PLAY

TV VOLUME TV VOLUME

PAUSE

TV INPUT TV INPUT

SKIP+

STOP

DISPLAY

SET MENU

V342650

VCR CBL/DBS TVDVD MENU

VCR REC (*1)

TV SLEEP

VCR PLAY

VCR REWIND

MENU SELECT

MENU LEFT

RECALL

CHANNEL

VCR POWER

VCR

CHANNEL +/–

CBL/DBS

CHANNEL +/–

TV VOLUME TV VOLUME

CHANNEL

ENTER

CHANNEL

ENTER

CHANNEL

ENTER

EFFECT

DISPLAY

VCR PAUSE

TV INPUT

VCR STOP

VCR FAST

FORWARD

POWER

VOLUME

MUTE

VOLUME VOLUME

MUTE MUTE

+10

DISC SKIP+/–

MENU SELECT

MENU LEFT

TITLE

Numeric

buttons

TV VOLUME

CLEAR

INDEX

MENU UP

TV INPUT

MENU RIGHT

MENU DOWN

RETURN

TV VOLUME

EFFECT

DISPLAY

VCR PAUSE

TV INPUT

VCR STOP

VCR FAST

FORWARD

CBL/DBS POWER

TV SLEEP

CHANNEL

VCR REC (*1)

VCR PLAY

VCR REWIND

CHANNEL +/–

VOLUME

TV MUTE

TV POWER

TV SLEEP

CHANNEL

+100

MENU UP

MENU RIGHT

DISPLAY

MENU DOWN

*1: Press this button twice to start recording.

*1: Appuyer deux fois sur cette touche pour lancer l’enregistrement.

*1: Diese Taste zweimal drücken, um die Aufnahme zu starten.

*1: Tryck två gånger på den här knappen för att börja spela in på videobandspelaren.

*1: Premere due volte questo tasto per iniziare la registrazione.

*1: Presione dos veces este botón para comenzar a grabar.

*1: Druk tweemaal op deze toets om te beginnen met opnemen.

Quick Reference Card

V342650

Yamaha RX-V495 El manual del propietario

Marca: Yamaha

Modelo: RX-V495

Categoría: Receptor

Tipo: El manual del propietario

Descargar PDF

informe

en otros idiomas

français: Yamaha RX-V495 Le manuel du propriétaire
italiano: Yamaha RX-V495 Manuale del proprietario
English: Yamaha RX-V495 Owner's manual
Deutsch: Yamaha RX-V495 Bedienungsanleitung
русский: Yamaha RX-V495 Инструкция по применению
Nederlands: Yamaha RX-V495 de handleiding
português: Yamaha RX-V495 Manual do proprietário
dansk: Yamaha RX-V495 Brugervejledning
polski: Yamaha RX-V495 Instrukcja obsługi
čeština: Yamaha RX-V495 Návod k obsluze
svenska: Yamaha RX-V495 Bruksanvisning
Türkçe: Yamaha RX-V495 El kitabı
suomi: Yamaha RX-V495 Omistajan opas
română: Yamaha RX-V495 Manualul proprietarului

Yamaha RX-V495 El manual del propietario

Yamaha RX-V495 El manual del propietario

en otros idiomas

Artículos relacionados

Otros documentos