Modern Forms WS-3120 Vogue Instrucciones de operación

Tipo
Instrucciones de operación
1
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the companys continuous improvement program.
INSTALLATION INSTRUCTION
Vogue
WS-3120, WS-3120F
HARDWARE
A1 B1 C1 D1 E1
Wire Connector
Qty: 3
7EAC112201
Junction Box Screw
Qty: 2pcs + 1 Extra
7MPF0415C2
#8-32X9/16” SS
Mounting Screw
Qty:1 Extra
4MPF0412S3BW(BZ)
7MPF0412S1(BN)(CH)
5/32-32X1/2”
Bronze/Nickel Plating
Fixture Screw
Qty: 4 pcs + 1 Extra
7MPF0311S3BK(BZ)
7MPF0313S1(BN)(CH)
1/8-40X7/16”
Bronze/Nickel Plating
Glass Holder
Qty: 2 pcs
4MBA534501BZ1(BZ)
4MBA534501BN1(BN)
4MBA534501CH (CH)
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de
l’électricité et les règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal
en position d’arrêt (« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces,
nen laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces
instructions peut annuler l’homologation ETL/CETL du luminaire.
MISE EN GARDE
Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e
instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor
de alimentación principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas
durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar
la calicación ETL/CETL esta lámpara.
PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
2
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
PREPARATION
y for installation.
MOUNTING THE FIXTURE (Fig. 1)
4. Secure the mounting back plate to the junction box using junction box screws (B1). The side of the mounting back plate marked “GND”
must face out.
CONNECTING THE WIRES (Fig. 2)
making sure that all wire connectors (A1) are secured. If your outlet box has
the green screw provided. After wires are connected, tuck them carefully
inside the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
6. Slide the glass into the front bracket; secure it with glass holder (E1)
7. Place the canopy plate over the mounting back plate; secure it with
the mounting screw (C1).
INSTALLATION INSTRUCTION
Vogue
WS-3120, WS-3120F
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
Junction Box
Ground Wire
B1 Junction Box Screw
D1 Fixture Screw
E1
Glass Holder
Front Bracket
Glass
RPL-GLA-3120
Mounting Screw C1
Canopy Plate
Mounting Backplate
A1
Wire Connector
WS-3120 Back Plate Dimensions
6 3/8”
1 3/8”
1 3/4”
4 1/8”
Switch
COMPLETING THE INSTALLATION (Fig. 1)
CONNECTING THE WIRES (Fig. 2)
sure that all wire connectors (A1) are secured. If your outlet box has a green
After wires are connected, tuck them carefully inside the junction box.
7. Place the canopy plate over the mounting back plate,secure it with the mounting screw(C1).
5. The lamp can switch between three color temperatures (2700K-3000K-3500K),
which can be adjusted to your preference with the switch in the canopy (Fig.3).
Note: color temperature adjustment is only applicable to models WS-3120.
1
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the companys continuous improvement program.
INSTALLATION INSTRUCTION
Vogue
WS-3127, WS-3127F, WS-3139, WS-3139F
HARDWARE
A1 B1 C1 D1 E1
Wire Connector
Qty: 3
7EAC112201
Junction Box Screw
Qty: 2pcs + 1 Extra
7MPF0415C2
#8-32X9/16” SS
Mounting Screw
Qty:1 Extra
4MPF0412S3BW(BZ)
7MPF0412S1(BN)(CH)
5/32-32X1/2”
Bronze/Nickel Plating
Fixture Screw
Qty: 4 pcs + 1 Extra
7MPF0311S3BK(BZ)
7MPF0313S1(BN)(CH)
1/8-40X7/16”
Bronze/Nickel Plating
Glass Holder
Qty: 2 pcs
4MBA534501BZ1(BZ)
4MBA534501BN1(BN)
4MBA534501CH (CH)
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de
l’électricité et les règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal
en position d’arrêt (« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces,
nen laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces
instructions peut annuler l’homologation ETL/CETL du luminaire.
MISE EN GARDE
Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e
instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor
de alimentación principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas
durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar
la calicación ETL/CETL esta lámpara.
PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
2
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
PREPARATION
y for installation.
4. Secure the mounting back plate to the junction box using junction box screws (B1). The side of the mounting back plate marked “GND” must
face out.
CONNECTING THE WIRES (Fig. 2)
making sure that all wire connectors (A1) are secured. If your outlet
directly to the back plate using the green screw provided. After wires
are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
6. Slide the glass into the front bracket; secure it with glass holder (E1)
7. Place the canopy plate over the mounting back plate; secure it with
the mounting screw (C1).
INSTALLATION INSTRUCTION
Vogue
WS-3127, WS-3127F, WS-3139, WS-3139F
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
WS-3127/WS-3127F Back Plate Dimensions WS-3139/WS-3139F Back Plate Dimensions
Junction Box
Ground Wire
M1
B1 Junction Box Screw
Mounting Screw
C1
D1
Fixture Screw
E1
Glass Holder
A1
Wire Connector
Mounting Backplate
Canopy Plate
Front Bracket
Glass
WS-3127/WS-3127F: (RPL-GLA-3115)
WS-3139/WS-3139F: (RPL-GLA-3120)
4 1/8”
1 3/4”
6 3/8”
1 3/8”
10 1/4”
1 3/8”
1 3/4”
4 1/8”
Switch
COMPLETING THE INSTALLATION (FIG. 1)
sure that all wire connectors (A1) are secured. If your outlet box has a green
After wires are connected, tuck them carefully inside the junction box.
7. Place the canopy plate over the mounting back plate,secure it with the mounting screw(C1).
5. The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch in the canopy
CONNECTING THE WIRES(FIG.2)
(Fig.4).Note: color temperature adjustment is only applicable to models WS-3127 and WS-3139.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Modern Forms WS-3120 Vogue Instrucciones de operación

Tipo
Instrucciones de operación