Yamaha S12 El manual del propietario

Categoría
Equipo de música suplementario
Tipo
El manual del propietario
GEO S12 Series
Geo S1210 & Geo S1230 Tangent Array Modules
Geo S12 Analog TD Controller
User Manual
GEO S12 Series User Manual V1.02
Date: 07/03/2008
Page 2/112 INTRODUCTION
GEO Technology is radically new thinking
The GEO R&D Project has, to date, resulted in the following patent applications:
The GEO Hyperboloid Reflective Wavesource™ differs radically from the megaphone-variant
type horns you know and love (or hate). “Tried and true” methods will produce entirely
unexpected results. HRW technology produces precise and predictable results.
The Configurable Directivity Flange. A waveguide that allows the operator to alter its behaviour.
An unprecedented NEXO development that is easy to use – once you know how and when.
The Directivity Phase Device needs no operator input to function, but it is reassuring to know that
the coupling of the midrange of the system is considered as important as the high frequencies…
DSP-driven Directional Sub-bass devices are a new approach to controlling LF/VLF acoustic
energy.
GEO is not hard to use when you understand how…
The technology behind GEO is revolutionary, but it is grounded in years of practical experience with the
problems of delivering high quality professional sound to large audiences at high SPL levels. The GEO
toolbox includes GEOSoft -a simple yet powerful and highly predictive design tool. The array assembly
system is keyed to the design software and will easily enable you to deploy your design with great
precision. The NX242 Digital TDcontroller provides driver protection and system optimization as well as
DSP-driven cardioid pattern control for the CD18, GEO SUB and RS series Directional Subwoofers.
GEO is a high precision system
The GEO HRW™ controls acoustic energy more precisely than other multiple element waveguides. It
also makes GEO less forgiving of mistakes. Whilst conventional horns never combine into a coherent
array, they may deliver acceptable results even if the design and deployment of the system is less than
optimal. This is not the case with GEO where careless installation produces catastrophic results.
A GEO Tangent Array is not a “line array”
GEO Technology is equally effective in designing and deploying tangent horizontal arrays or curved
vertical arrays. For best results in a specific application the user needs to know how multi-speaker
arrays interact with audience geometry, along with the benefits and drawbacks of curved vertical arrays
and horizontal arrays.
Curved tangent arrays require different design techniques
For the past 20 years, sound reinforcement professionals have worked with horizontal arrays that use
conventional horns to deliver [more or less] ‘equal power to equal angles’. Curved vertical arrays are
designed to deliver [more or less] equal power to equal areas’. When arrays use conventional horns,
the lack of precision, overlap and interference masks errors in array design and aiming. The highly
precise GEO wavesource responds accurately, consistently and predictably to the design and
deployment of a curved vertical tangent array. This is why the GEO rigging system is designed to
control angular splay to 0.01° precision.
GEO curved tangent arrays require different operational techniques
Over the years, system designers and operators have developed a number of signal processing
techniques to disguise and partly overcome the limitations of horn design. “Frequency shading,”
“amplitude shading,” “system tuning,” all of these are tools of the advanced sound system operator.
NONE OF THESE TECHNIQUES ARE APPLICABLE TO GEO TANGENT ARRAYS. Instead of
enhancing the array’s performance they will severely degrade it.
Take time to learn how to get great results with GEO Technology. It is an investment that will pay off in
more satisfied clients, more efficient operating procedures and more recognition for your skill as a
sound system designer and operator. A comprehensive understanding of GEO theory, tangent arrays,
and specific features of the GEO S12 Series will help you to operate your system at its full potential.
INTRODUCTION Page 3/112
SAFETY ISSUES
IMPORTANT NOTICE CONCERNING HIGH SOUND PRESSURE LEVELS
Exposure to extremely high noise levels may cause a permanent hearing loss.
Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly
everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient
time. The U.S. Government’s Occupational and Health Administration (OSHA) has
specified the following permissible noise level exposures: Sound Duration Per
Day In Hours Sound Level dBA, Slow Response
8 90
6 92
4 65
3 97
2 100
1 ½ 102
1 105
½ 110
¼ or less 115
According to OSHA, any exposure in excess of the above permissible limits could result in some
hearing loss. Ear plugs or protectors to the ear canals or over the ears must be worn when operating
this amplification system in order to prevent a permanent hearing loss, if exposure is in excess of the
limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure
levels, it is recommended that all persons exposed to equipment capable of producing high sound
pressure levels such as this amplification system be protected by hearing protectors while this unit is in
operation.
SYSTEM RIGGING SAFETY RULES
Before use of GEO S12, please ensure that anyone involved in system deployment
understands the rigging and stacking Safety rules are described in chapter “GEO S12
hardware setup procedure”, “SAFETY FIRST” pages 31 to 33 . Failure to do this exposes
people to potential injury or death.
ELECTRICAL SAFETY
WARNING ! GEO S12 TDCONTROLLER AND NX242 DIGITAL CONTROLLER ARE CLASS 1
APPARATUS AND MUST BE EATHED.
The green and yellow wire of the mains cord must always be connected to an installation
safety earth or ground. The earth is essential for personal safety as well as the correct
operation of the system, and is internally connected to all exposed metal surfaces.
Page 4/112 INTRODUCTION
CONTENTS
1 Introduction.....................................................................................................................9
2 GEO S12 General Set-up Instructions.........................................................................12
2.1 Speaker connection.................................................................................................12
2.1.1 GEO S12 connectors........................................................................................12
2.1.2 Configuring Geo S12 for Passive or Active Mode.............................................12
2.1.3 Cabling .............................................................................................................12
2.1.4 Example:...........................................................................................................13
3 Amplifier Selection for use with GEO S12s................................................................14
3.1 GEO S12 recommended amplification.....................................................................14
3.1.1 Current rating....................................................................................................14
3.1.2 Amplifier settings ..............................................................................................14
3.1.3 Example............................................................................................................16
3.2 GEO S12s and NXAMP TDControllers....................................................................16
3.2.1 NXAMP connectors ..........................................................................................16
3.2.2 GEO S12s and NXAMP recommended configurations.....................................17
4 GEO S12 Setups on NEXO TD Controllers .................................................................18
4.1 Digital NX242-ES4 and NXAMP TDControllers.......................................................18
4.2 Analogue GEOS12 TDController.............................................................................19
5 Connection diagrams...................................................................................................19
5.1 GEO S12 & RS15 with GEOS12 TDController (Mono Omni Mode) ........................19
5.2 GEO S12 / NX242-ES4 (4 channels passive mode)................................................20
5.3 GEO S12 / ALPHA S2 / NX242-ES4 (Stereo passive mode) ..................................21
5.4 GEO S12 / CD18 / NX242-ES4 (Stereo passive mode) ..........................................22
5.5 GEO S12 / GEO SUB / NX242-ES4 (Stereo passive mode) ...................................23
5.6 GEO S12 / NXAMP4x1 (Bridge Stereo - Passive mode).........................................24
5.7 GEO S12 / NXAMP4x1 (Bridge Stereo - Active mode)............................................25
5.8 GEO S12 / NXAMP4x4 (4 Channels - Passive mode).............................................26
5.9 GEO S12 / NXAMP4x4 (Stereo Active mode).........................................................27
INTRODUCTION Page 5/112
6 GEOSoft2.......................................................................................................................28
7 Configurable Directivity Device...................................................................................29
7.1 Installing & removing GEO’s Configurable Directivity flanges .................................29
7.2 When & where to use Configurable Directivity flanges............................................30
8 GEO S12 hardware setup procedure ..........................................................................31
8.1 SAFETY FIRST.......................................................................................................31
8.1.1 Flown Systems Safety...................................................................................... 31
8.1.2 Ground Stacking Safety ...................................................................................32
8.1.3 Contacts ........................................................................................................... 33
8.2 General Description.................................................................................................34
8.2.1 Described configurations..................................................................................35
8.2.2 WARNINGS ON GEO S12 ACCESSORIES .................................................... 36
8.3 GEO S12 in fixed installations.................................................................................37
8.3.1 Fixed installation Accessories and kits .............................................................37
8.3.2 Single GEO S12 rigidly mounted on a wall or a ceiling (vertical or horizontal) . 38
8.3.3 Single GEO S12 cable mounted on a wall or a ceiling (vertical or horizontal).. 39
8.3.4 GEO S12 vertical array rigidly mounted on a ceiling ........................................ 40
8.3.5 GEO S12 vertical array cable mounted on a ceiling ......................................... 42
8.3.6 GEO S12 horizontal array rigidly mounted on a ceiling ....................................43
8.3.7 GEO S12 horizontal array cable mounted on a ceiling..................................... 45
8.4 GEO S12 in touring applications .............................................................................46
8.4.1 Touring Accessories......................................................................................... 46
8.4.2 Single GEO S12 on speaker stand or on RS15 horizontally ............................47
8.4.3 Single GEO S12 flown vertically.......................................................................49
8.4.4 Single GEO S12 flown horizontally...................................................................50
8.4.5 Two GEO S12 on wind-up stand or on RS15 horizontally................................ 51
8.4.6 Two GEO S12 flown horizontally......................................................................55
8.4.7 Two or more GEO S12 flown vertically............................................................. 56
8.4.8 Three or more GEO S12 flown horizontally...................................................... 59
8.4.9 Ground stacked GEO S1210............................................................................63
8.5 Testing and Maintenance of the system..................................................................67
Page 6/112 INTRODUCTION
9 NEXO Analogue Geo S12TD Controller......................................................................68
9.1 Analogue TDcontroller Declaration of conformity.....................................................68
9.2 IMPORTANT SAFETY INSTRUCTIONS.................................................................68
9.3 Analogue TDcontroller Setting-Up Advice ...............................................................69
9.3.1 Mains Power.....................................................................................................69
9.3.2 Voltage setting..................................................................................................69
9.3.3 Mounting the TDcontroller in a rack (Grounding, shielding & safety issues).....69
9.3.4 Fuse .................................................................................................................69
9.3.5 Recommendations for wiring the sense lines ...................................................70
9.3.6 Recommendations for wiring the audio outputs................................................70
9.3.7 Electromagnetic environments .........................................................................70
9.3.8 Analogue signal cables.....................................................................................70
9.4 Analogue TDcontroller USER GUIDE......................................................................71
9.4.1 Read before use ...............................................................................................71
9.4.2 Front Panel .......................................................................................................72
9.4.3 Rear Panel........................................................................................................73
9.5 TDcontroller REFERENCE GUIDE..........................................................................74
9.5.1 Linear section ...................................................................................................74
9.5.2 Servo Control section ..................................................................................................74
10 NEXO NX242-ES4 Digital Controller for GEO S12..................................................76
10.1 NX242 Proprietary Functions...................................................................................76
10.1.1 Upgradable Firmware .......................................................................................76
10.1.2 EQ & Filtering ...................................................................................................76
10.1.3 Protection .........................................................................................................77
INTRODUCTION Page 7/112
10.2 Trouble shooting......................................................................................................78
10.2.1 Operation of Multiple TDcontrollers output channels........................................ 78
10.2.2 Amplifier Power (MENU 2.7) ............................................................................ 78
10.2.3 Amplifier Gain (MENU 2.6)............................................................................... 78
10.2.4 Gains................................................................................................................ 78
10.2.5 Delays ..............................................................................................................79
10.2.6 Reversed Cardioid Pattern ...............................................................................79
10.2.7 Using the wrong NX242 setups for a given cabinet..........................................79
10.2.8 Connections ..................................................................................................... 79
11 System alignment guidelines...................................................................................80
11.1 GEO S12 Vertical Cluster design ............................................................................80
11.2 Stacked RS15 / CD18 / S2 / GEO SUB and Flown GEO S12.................................80
11.3 Driving the GEO SUB’s from the AUX send............................................................81
11.4 Recommended installation tools and equipment.....................................................81
12 GEO S12 – RS15 / CD18/S2/GEOSUB System Check List.....................................83
12.1 Are the NX242 Digital TDcontrollers properly configured?......................................83
12.1.1 NX242 settings .................................................................................................83
12.2 Are the amplifiers properly configured?...................................................................83
12.3 Are the amps and the NX properly connected?.......................................................83
12.4 Are the speakers properly connected and angled ? ................................................84
12.5 Final Pre-Sound Check Check ................................................................................84
13 Technical Specifications..........................................................................................85
13.1 GEO S1230 Module ................................................................................................85
13.1.1 System specifications.......................................................................................85
13.1.2 Dimensions ......................................................................................................86
13.1.3 Diagrams..........................................................................................................86
13.2 GEO S1210 Module ................................................................................................87
13.2.1 System specifications.......................................................................................87
13.2.2 Dimensions ......................................................................................................88
13.2.3 Diagrams..........................................................................................................88
Page 8/112 INTRODUCTION
13.3 GEO S12 Touring Applications Accessories............................................................89
13.3.1 GEO S12 Bumper.............................................................................................89
13.3.2 GEO S12 Rigging Plates ..................................................................................90
13.3.3 Tension Mode Link Bars for GEOS12-XBOW-V2.............................................91
13.3.4 Lifting Ring........................................................................................................92
13.3.5 Truss hook for GEOS12-SSBRK or GEOS12-PSBRK .....................................93
13.3.6 Truss hook for single vertical GEO S12............................................................94
13.3.7 “U” Bracket for single vertical GEO S12 ...........................................................95
13.3.8 U” Bracket for two vertical GEO S12 ................................................................96
13.3.9 Ground Stacking Device for up to 6 GEO S1210..............................................97
13.4 GEO S12 Fixed Installations Accessories ...............................................................98
13.4.1 GEO S12 Bumper.............................................................................................98
13.4.2 GEO S12 Connecting Plate 1 ...........................................................................99
13.4.3 GEO S12 Connecting Plate 2 .........................................................................100
13.4.4 GEO S12 Connecting Plate 3 .........................................................................101
13.4.5 Single GEO S12 “U” Bracket ..........................................................................102
13.4.6 “L” Bracket for cable suspension ....................................................................103
13.4.7 “U” Bracket for rigid suspension .....................................................................104
13.4.8 GEO S12 Push-Pins (BLGEOS).....................................................................105
13.5 GEO S12 Analogue TDcontrollers.........................................................................106
13.5.1 Specifications .................................................................................................106
13.5.2 Front and Rear Panel view .............................................................................106
13.6 NX242 TDcontroller with NX-Tension Card ...........................................................107
13.6.1 Specifications .................................................................................................107
13.6.2 Front and Rear Panel view .............................................................................107
13.6.3 Block Diagram ................................................................................................108
14 GEO S12 Series Parts & Accessories List ............................................................109
14.1 Modules & Control Electronics List........................................................................109
14.2 Accessories List.....................................................................................................109
15 USER NOTES...........................................................................................................111
INTRODUCTION Page 9/112
1 INTRODUCTION
Thank you for selecting a NEXO GEO S12 Series Tangent Array System. This manual is intended to
provide you with necessary and useful information about your GEO S12 System, which includes the
following products:
GEO S1230 is a 30° Tangent Array Module.
It comprises 1x12” (30cm) Neodynium 16
ohms LF/MF driver and 1x3” voice coil, 1.4”
Throat 16 Ohm HF Driver loaded by a 28.5°
Hyperboloid Reflective Wavesource™.
GEO S1210 is a 10° Tangent Array Module.
It comprises 1x12” (30cm) Neodynium 16
ohms LF/MF driver and 1x3” voice coil, 1.4”
Throat 16 Ohm HF Driver loaded by a 5°
Hyperboloid Reflective Wavesource™.
GEO S12 Accessory Range. a full range of accessories that provides safe, flexible and simple
means of installing Geo S12 Tangent Arrays in fixed installation as well as in touring applications.
Page 10/112 INTRODUCTION
As for all NEXO systems, GEO S12s are controlled, powered and monitored by dedicated NEXO
TDControllers:
GEO S12 TDController is based on PS analogue TDController design, and provides full control
for RS15 subwoofer in omnidirectional mode associated to Geo S12. It has 2 analogue inputs
(Left and Right) and 3 analogue outputs (RS15 Mono Omni, GeoS12 Left and GeoS12 Right);
NX242-ES4 Digital TDController provides comprehensive control of GEO S12 loudspeakers in
multiple configurations. It allows Ethersound
TM
digital audio networking, as well as remote control
for all units in the network. It has 2 analogue / 4 digital inputs and 4 analogue / 4 digital outputs;
IMPORTANT
NX242 must be equipped with NX-Tension Card (ES4 or CAI) to access GEO S12 setups
NXAMP4x1 and NXAMP 4x4 are Powered Digital Controllers, providing full control and
amplification for RS15 in multiple configurations. Both devices feature 4 analogue inputs and 4
speaker outputs. When equipped with optional card, 4 digital inputs in Ethersound
TM
digital audio
network format as well as remote control for all units in the network become available.
For a complete description of these controllers, please refer to User Manuals. The NX242 and NXAMP
DSP algorithms and parameters are fixed in software and updated regularly: Please consult the NEXO
web site (www.nexo.fr
) for the latest software releases.
GeoD Passive mode
Crossover 80Hz
INTRODUCTION Page 11/112
GEOSoft2 Array Design Software assists in the design and implementation of vertical tangent
GEO arrays. Please consult the NEXO web site (www.NEXO.fr or www.NEXO-sa.com) for the
latest software releases.
Please devote your time and attention to reading this manual. A comprehensive understanding of GEO
theory, tangent arrays and specific features of GEO S12 will help you to operate your system at its full
potential.
Page 12/112 GEO S12 GENERAL SET-UP INSTRUCTIONS
2 GEO S12 GENERAL SET-UP INSTRUCTIONS
2.1 Speaker connection
2.1.1 GEO S12 connectors
GEO S12 is connected with Speakon NL4FC plugs (not supplied). A wiring
diagram is printed on the connection panel located on the back of each
cabinet.The 4 pins of the 2 Speakon sockets identified in / out are connected in
parallel within the enclosure.
Either connector can be used to connect amplifier or to link to an additional Geo
S12 cabinet or to link to an optional Sub (if present). Therefore, a single 4-
conductor cable can connect two amplifier channels to various Geo S12 and/or
Sub Bass.
Connectors are wired as follows:
2.1.2 Configuring Geo S12 for Passive or Active Mode
Remove the six TORX screws that hold the connector panel (figure next page);
Remove the connector panel so that filter WAGO connectors become accessible;
In Passive Mode, connector A (from filter) should be inserted in connector B (PCB “Passive In”),
and Connector D (“Passive Out”) should be connected to speakers via connector C.
In Active Mode, WAGO Connector A (from filter) should be directly connected into to speakers via
connector C (PCB connectors B & D are then unused).
2.1.3 Cabling
NEXO recommends the exclusive use of multi-conductor cables to connect the system: the cable kit is
compatible with all the cabinets, and there is no possible confusion between LF, MF and HF sections.
Cable choice consists mainly of selecting cables of the correct sectional dimension (size) in relation to
the load resistance and the cable length. Too small a cable section will increase both its serial
resistance and its capacitance; this reduces the electrical power delivered to the loudspeaker and can
also induce response (damping factor) variations.
For a serial resistance less or equal to 4% of the load impedance (damping factor = 25), the maximum
cable length is given by:
L
max
= Z x S S in mm
2
, Z in Ohm, L
max
in meters
The table below indicates these values, for 3 common sizes.
Load Impedance ()
2 3 4 6 8 12 16
Cable section Maximum Length (meters)
1,5 mm² (AWG #14) 3 4.5 6 9 12 18 24
2,5 mm² (AWG #12) 5 7.5 10 15 20 30 40
4 mm² (AWG #10) 8 12 16 24 32 48 64
Speakon
Connector
Passive
Mode
Active
Mode
1(-)
Ö
Not Connected Geo S12 LF (-)
1(+)
Ö
Not Connected Geo S12 LF (+)
2(-)
Ö
Geo S12 (-) Geo S12 HF (-)
2(+) Geo S12 (+) Geo S12 HF (+)
GEO S12 GENERAL SET-UP INSTRUCTIONS Page 13/112
2.1.4 Example:
GEO S12 has a 16 Ohms nominal impedance in passive mode, so 4x Geo S12 wired in parallel
will present a 16/4 = 4 Ohm load impedance. The maximum acceptable 2x2.5 mm
2
(AWG #12)
cable length L
max
for such a cluster is 10 meters.
IMPORTANT
Long speaker cables induce capacitive effects – up to hundreds of pF depending on the
quality of the cable - with a high-pass effect on high frequencies. If long speaker cables
must be used, ensure that they do not remain coiled while in use.
CONNECTOR PANEL PASSIVE MODE ACTIVE MODE
B
A
D
C
B
D
A
C
Page 14/112 AMPLIFIER SELECTION FOR USE WITH GEO S12S
3 AMPLIFIER SELECTION FOR USE WITH GEO S12S
NEXO recommends high power amplifiers in all cases. Budget constraints are the only reason to select
lower power amplifiers. A lower power amplifier will not reduce the chances of driver damage due to
over-excursion, and may actually increase the risk of thermal damage due to sustained clipping. If an
incident occurs on an installation without protection, the fact that amplifiers only generating half their
rated output power (-3dB) are used will not change anything in respect of possible damage. This is due
to the fact that the RMS power handling of the weakest component in the system is always 6 to 10 dB
lower than the amplifier rating.
3.1 GEO S12 recommended amplification
GEO S12 is rated for very high power handling and has a 16 Ohms nominal impedance in passive
mode or 2 x 16 Ohms nominal impedance in active mode.
These high impedance values allow connection of 3 to 6 cabinets in parallel for each amplifier channel.
Nexo recommends amplifiers in agreement with table below:
Recommended
Amplifier#
Channel 1
LF in Active Mode or
LF+HF in Passive Mode
Channel 2
HF in Active Mode
GEO S12 Passive Mode
3 in parallel (5.3 Ohms load)
1750 to 3100 W / 4 Ohms
GEO S12 Active Mode
3 in parallel (5.3 Ohms load)
1750 to 3100 W / 4 Ohms 875to 1550 W / 4 Ohms
GEO S12 Passive Mode
4 in parallel (4 Ohms load)
2000 W to 3600 W / 4 Ohms -
GEO S12 Active Mode
4 in parallel (4 Ohms load)
2000 to 3600 W / 4 Ohms 1000 to 1800 W / 4 Ohms
GEO S12 Passive Mode
6 in parallel (2.7 Ohms load)
3300 to 6000 W / 2 Ohms
GEO S12 Active Mode
6 in parallel (2.7 Ohms load)
3300 to 6000 W / 2 Ohms 1650 to 3000 W / 2 Ohms
3.1.1 Current rating
It is very important that the amplifier behaves correctly under low load conditions. A speaker system is
reactive by nature: on transient signals like music it will require four to ten times more instantaneous
current than its nominal impedance would indicate. Amplifiers are generally specified by continuous
RMS power into resistive loads, however the only useful information about current capacity is the
specification into a 2 Ohm load. It is possible to perform an amplifier listening test by loading the amps
with twice the number of cabinets considered for the application (2 speakers per channel instead of one,
4 instead of 2) and running the amps up to the onset of clipping. If the signal does not noticeably
deteriorate, the amplifier is well adapted (overheating after approximately ten minutes is normal but
thermal protection must not operate too quickly after starting this test).
3.1.2 Amplifier settings
Gain value
Gain is the key to correct alignment of the system. It is especially important to know the gain of all
amplifiers used in your set-up. The tolerance should be about ±0.5 dB. In practice this can be difficult to
achieve because:
AMPLIFIER SELECTION FOR USE WITH GEO S12S Page 15/112
Some amplifier brands have an identical input sensitivity for models of different power rating (this
infers a different voltage gain for each model). For example, a range of amplifiers with different
power outputs, all having a published input sensitivity of 775mV/0dBm or 1.55V/+6dBm, will have
a wide range of actual gains – the higher the power, the greater the gain.
Various other brands may offer constant gain but only within a given product range, for example
they may fit fixed input sensitivity only on their semi-professional amps.
Even if a manufacturer applies the constant gain rule to all models, the value selected will not
necessarily be the same as that chosen by other manufacturers.
Some products can exhibit manufacturing tolerances for the same model of ±1dB or more. Some
amplifiers may have been modified, possibly without any label indicating the new values. Others
may have gain switches fitted internally where it is impossible for the user to verify the actual
setting without opening the amplifier casing.
In cases where you don't know the gain of your amplifier (or want to check it) please follow this
procedure:
1) Unplug any loudspeakers from the amplifier outputs
2) With a signal generator, feed a sine wave at 1000Hz at a known voltage (say 0.5V) to
the input of the amplifier under test
3) Measure the voltage at the output of the amplifier
4) Calculate the gain using the formula Gain = 20 * LOG
10
(Vout/Vin).
Some examples:
Vin / Gain 20dB 26dB 32dB 37dB (1.4V sensitivity / 1350Wrms)
0.1 V 1 V 2 V 4 V 7.1 V
0.5 V 5 V 10 V 20 V 35.4 V
1 V 10 V 20 V 40 V 70.8 V
Remember that constant sensitivity settings will give a different gain value when the amplifier power is
different.
NEXO recommends low gain amplifiers: +26dB is recommended, as it is at the same time adequately
low and quite common amongst amplifier manufacturers. This gain setting improves signal to noise ratio
and allows all preceding electronic equipment, including the NX242 TDcontroller or GEO S12
TDController, to operate at optimum level. Remember that using a high gain amplifier will raise the
noise floor proportionally.
Operating Mode
Most two channel amplifiers available on the pro-audio market have the following operating modes:
Stereo:
two fully independent channels deliver identical power into identical loads
NEXO recommends Stereo Mode for all amplifier channels feeding GEO S12’s.
Bridge-Mono:
the second signal channel processes the same input as the first channel, but with
reversed phase. The (single) load is connected between the two positive channel outputs using a
suitable connection. While the total output of the amplifier remains the same, the available output
voltage, the minimum impedance that can be connected and the voltage gain are doubled as
compared with stereo operation. Typically, only channel 1 input is active. Positive and negative
output connections vary depending on amplifier manufacturers.
NEXO does not recommend Bridge Mono Mode unless amplifier power is clearly not sufficient.
Page 16/112 AMPLIFIER SELECTION FOR USE WITH GEO S12S
IMPORTANT
When in Bridge-Mono mode, check your amplifier user manual for proper connection of
outputs 1(+) and (2+) in relation to input phase.
Parallel-mono: the output terminals of the two channels are configured in parallel using an
internal relay. The (single) load is connected either to the output of channel 1 or to that of channel
2 (as if in stereo). While the total output of the amplifier remains the same the output voltage level
is also the same as in stereo mode. The minimum impedance that can be connected is reduced
by half due to the fact that current capability is doubled. Typically, only channel 1 input is active.
NEXO does not recommend Parallel-Mono Mode for any GEO S12 amplification.
Warning on amplifiers signal processing features
Some high-end amplifiers may include signal processing functions similar to those found in the NX242
TDcontroller or in GEO S12 TDController ("loudspeaker offset integration", "limiter", "compressor," etc.).
Moreover, when this processing is digital, computation latency time can introduce a few milliseconds
delay from input to output. These functions are not adapted to specific system requirements and may
interfere with the complex protection algorithms used in the NX242.
NEXO do not advise using other protection systems in conjunction with the NX242 and they should be
disabled.
IMPORTANT
For proper system protection, no latency time or non-linear devices should be
introduced between the output of the NX242 TDcontroller and the input of loudspeakers
through use of DSP modules such as internal amplifier signal processing.
3.1.3 Example
For a 6 GEO S12 cluster, and considering an amplifier model which is capable of delivering 2 x 3300W
into 2 Ohms or 2 x 2300W into 4 Ohms, NEXO recommends the following quantities and settings:
Geo S12 Passive Mode:
1 stereo amplifier, 3 x GEO S12 per amplifier channel, mode switch in Stereo position, Gain
switch in 26 dB gain position, all dynamic or filter processing switches off.
3.2 GEO S12s and NXAMP TDControllers
NEXO Powered TDControllers NXAMP 4X1 & 4X4 are integrated solutions for Control and amplification
for all NEXO speaker ranges.
NXAMP4x1 and NXAMP4x4 power capability is listed in the table below:
Mode 4 Channels Bridge Stereo
NXAMP4x1 4 x 650 Watts / 8 Ohms
4 x 900 Watts / 4 Ohms
4 x 1300 Watts / 2 Ohms
2 x 1800 Watts / 8 Ohms
2 x 2600 Watts / 4 Ohms
NXAMP4x4 4 x 1900 Watts / 8 Ohms
4 x 3400 Watts / 4 Ohms
4 x 4000 Watts / 2 Ohms
2 x 6800 Watts / 8 Ohms
2 x 8000 Watts / 4 Ohms
3.2.1 NXAMP connectors
NXAMP4x1 and NXAMP4x4 rear panels feature:
4 analog inputs / outputs (links) on XLR3 connectors;
4 digital inputs / outputs on RJ45 connectors with optional card;
4 speaker level outputs on NL4FC connectors.
AMPLIFIER SELECTION FOR USE WITH GEO S12S Page 17/112
Figure below shows connectors implementation on the rear panel.
3.2.2 GEO S12s and NXAMP recommended configurations
Passive Mode Active Mode
3 GEO S12 1 channel of NXAMP4x1 in Bridge Stereo Mode
1 channel of NXAMP4x4 in 4 channels mode
2 channels of NXAMP4x1 in Bridge Stereo Mode
2 channels of NXAMP4x4 in 4 channels mode
4 GEO S12 1 channel of NXAMP4x4 in 4 channels mode 2 channels of NXAMP4x4 in 4 channels mode
Page 18/112 GEO S12 SETUPS ON NEXO TD CONTROLLERS
4 GEO S12 SETUPS ON NEXO TD CONTROLLERS
4.1 Digital NX242-ES4 and NXAMP TDControllers
At GEO S12 User Manual current version printing time, 38 setups combining GEO S12s with NEXO
subwoofers are available in NX242 / NXAMP load 2.45. Please consult www.nexo-sa.com for upgrade
releases.
GEO S12 - 4 x S1210 Passive Wideband;
- 4 x S1230 Passive Wideband;
- 2 x S1210 Active Wideband;
- 2 x S1230 Active Wideband;
- 2 x S1210 Active X-Over 80 Hz;
- 2 x S1230 Active X-Over 80 Hz;
GEO S12
& ALPHA S2
- 2 x S1210 Passive Wideband + 2 x Alpha S2;
- 2 x S1230 Passive Wideband + 2 x Alpha S2;
- 2 x S1210 Passive X-Over 80 Hz + 2 x Alpha S2;
- 2 x S1230 Passive X-Over 80 Hz + 2 x Alpha S2;
GEO S12
& GEO SUB
- 2 x S1210 Passive Wideband + 1 x GeoSub 35 Hz – 80 Hz;
- 2 x S1230 Passive Wideband + 1 x GeoSub 35 Hz – 80 Hz;
- 2 x S1210 Passive Wideband + 1 x GeoSub 35 Hz – 200 Hz;
- 2 x S1230 Passive Wideband + 1 x GeoSub 35 Hz – 200 Hz;
- 2 x S1210 Passive X-Over 80 Hz + 1 x GeoSub 35 Hz – 80 Hz;
- 2 x S1230 Passive X-Over 80 Hz + 1 x GeoSub 35 Hz – 80 Hz;
- 2 x S1210 Passive X-Over 80 Hz + 1 x GeoSub 35 Hz – 200 Hz;
- 2 x S1230 Passive X-Over 80 Hz + 1 x GeoSub 35 Hz – 200 Hz;
- 2 x S1210 Active X-Over 80 Hz + 1 x GeoSub 35 Hz – 80 Hz;
- 2 x S1230 Active X-Over 80 Hz + 1 x GeoSub 35 Hz – 80 Hz;
- 2 x S1210 Active X-Over 80 Hz + 1 x GeoSub 35 Hz – 200 Hz;
- 2 x S1230 Active X-Over 80 Hz + 1 x GeoSub 35 Hz – 200 Hz;
GEO S12
& CD18
- 2 x S1210 Passive Wideband + 1 x CD18 85Hz;
- 2 x S1230 Passive Wideband + 1 x CD18 85 Hz;
- 2 x S1210 Passive X-Over + 1 x CD18 85 Hz;
- 2 x S1230 Passive X-Over + 1 x CD18 85 Hz;
- 2 x S1210 Active X-Over + 1 x CD18 85 Hz;
- 2 x S1230 Active X-Over + 1 x CD18 85 Hz;
GEO S12
& RS15
- 2 RS15 omni 35Hz-80Hz + 2 x S1210 Passive Wideband
- 2 RS15 omni 35Hz-80Hz + 2 x S1230 Passive Wideband
- 1 x RS15 cardio 35Hz-80Hz + 1 x S1210 Active Wideband
- 1 x RS15 cardio 35Hz-80Hz + 1 x S1230 Active Wideband
- 2 RS15 omni 35Hz-80Hz + 2 x S1210 Passive X-Over
- 2 RS15 omni 35Hz-80Hz + 2 x S1230 Passive X-Over
- 1 x RS15 cardio 35Hz-80Hz + 2 x S1210 Passive X-Over
- 1 x RS15 cardio 35Hz-80Hz + 2 x S1230 Passive X-Over
- 1 x RS15 cardio 35Hz-80Hz + 1 x S1210 Active X-Over
- 1 x RS15 cardio 35Hz-80Hz + 1 x S1230 Active X-Over
CONNECTION DIAGRAMS Page 19/112
4.2 Analogue GEOS12 TDController
GEO S12 TDController parameters have been optimized for 1 x RS15 (omni mode, mono) used in
conjunction with 2 x GEO S1210’s or 2 Geo x S1230’s (mono or stereo).
5 CONNECTION DIAGRAMS
5.1 GEO S12 & RS15 with GEOS12 TDController (Mono Omni Mode)
AMPLIFIER 1
AMPLIFIER 2
MONO
STEREO
Speakon 4
1 (+) / 1 (-) VLF1 *
2 (+) / 2 (-) VLF2 *
Speakon 4
Speakon 4
Speakon 4
Speakon 4
1 (+) / 1 (-) N.C.
2 (+) / 2 (-) FULL RANGE
Speakon 4
1 (+) / 1 (-) VLF
2 (+) / 2 (-) N.C.
TO AMPLIFIERS
B
ALANC
E
D IN
P
UT
S
RIGHT
LEFT
-
6dB
-
12dB
0dB
OUT
P
UT
L
E
V
E
L
B
ALANC
E
D OUT
P
UT
S
RIGHT LEFTSUB L+R
E
A
R
TH
LI
F
T
FROM AMPLIFIERS
+ 3-
+ 2 - + 1 -
S
E
N
S
E
IN
P
UT
(from amp terminals)
CAUTION
!
Sense must be connected for
speaker protection
SEE USER MANUAL
STEREO
IN
GEOS12
LEFT
GEOS12
RIGHT
SUB
OUT
GEOS12
LEFT
GEOS12
RIGHT
SUB
* VLF1 and VLF2 on one amplifier channel
Page 20/112 CONNECTION DIAGRAMS
5.2 GEO S12 / NX242-ES4 (4 channels passive mode)
AMPLIFIER 1
AMPLIFIER 2
GEOS12
#3
IN
1
TO AMPLIFIERS
STEREO
FROM AMPLIFIERS
GEOS12
#3
GEOS12
#4
+ 4 - + 3-
STEREO
GEOS12
4 CHANNELS
+ 2 - + 1 -
Speakon 4
Speakon 4
Speakon 4
1 (+) / 1 (-) N.C.
2 (+) / 2 (-) FULL RANGE
GEOS12
#4
Speakon 4
Speakon 4
Speakon 4
Speakon 4
Speakon 4
GEOS12
#1
GEOS12
#2
IN
2
GEOS12
#1
GEOS12
#2
CONNECTION DIAGRAMS Page 21/112
5.3 GEO S12 / ALPHA S2 / NX242-ES4 (Stereo passive mode)
AMPLIFIER 1
AMPLIFIER 2
GEOS12
LEFT
STEREO
IN
TO AMPLIFIERS
STEREO
FROM AMPLIFIERS
GEOS12
LEFT
GEOS12
RIGHT
+ 4 - + 3-
STEREO
GEOS12 STEREO MODE
WITH S2 SUB STEREO
SUB
RIGHT
SUB
LEFT
Speakon 4
SUB
LEFT
SUB
RIGHT
+ 2 - + 1 -
1 (+) / 1 (-) VLF
2 (+) / 2 (-) N.C.
Speakon 4
Speakon 4
Speakon 4
Speakon 4
1 (+) / 1 (-) N.C.
2 (+) / 2 (-) FULL RANGE
GEOS12
RIGHT
Speakon 4
1 (+) / 1 (-) VLF
2 (+) / 2 (-) N.C.
Page 22/112 CONNECTION DIAGRAMS
5.4 GEO S12 / CD18 / NX242-ES4 (Stereo passive mode)
AMPLIFIER 1
AMPLIFIER 2
GEOS12
LEFT
STEREO
IN
TO AMPLIFIERS
STEREO
FROM AMPLIFIERS
GEOS12
LEFT
GEOS12
RIGHT
+ 4 - + 3-
STEREO
GEOS12 STEREO MODE
WITH CD18 MONO
SUB
FRONT
SUB
REAR
Speakon 4
SUB
REAR
SUB
FRONT
+ 2 - + 1 -
1 (+) / 1 (-) REAR
2 (+) / 2 (-) FRONT
Speakon 4
Speakon 4
Speakon 4
Speakon 4
1 (+) / 1 (-) N.C.
2 (+) / 2 (-) FULL RANGE
GEOS12
RIGHT
CONNECTION DIAGRAMS Page 23/112
5.5 GEO S12 / GEO SUB / NX242-ES4 (Stereo passive mode)
AMPLIFIER 1
AMPLIFIER 2
GEOS12
LEFT
STEREO
IN
TO AMPLIFIERS
STEREO
FROM AMPLIFIERS
GEOS12
LEFT
GEOS12
RIGHT
+ 4 - + 3-
STEREO
GEOS12 STEREO MODE
WITH GEO SUB MONO
SUB
FRONT
SUB
REAR
Speakon 4
SUB
REAR
SUB
FRONT
+ 2 - + 1 -
1 (+) / 1 (-) REAR
2 (+) / 2 (-) FRONT
Speakon 4
Speakon 4
Speakon 4
Speakon 4
1 (+) / 1 (-) N.C.
2 (+) / 2 (-) FULL RANGE
GEOS12
RIGHT
Page 24/112 CONNECTION DIAGRAMS
5.6 GEO S12 / NXAMP4x1 (Bridge Stereo - Passive mode)
SP4
SP4
IN A
OUT A
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
OUT D
IN B
CONNECTION DIAGRAMS Page 25/112
5.7 GEO S12 / NXAMP4x1 (Bridge Stereo - Active mode)
SP4
SP4
IN A
OUT A
SP4
SP4
SP4
OUT D
4 x HF
4 x LF
Page 26/112 CONNECTION DIAGRAMS
5.8 GEO S12 / NXAMP4x4 (4 Channels - Passive mode)
SP4
SP4
IN A
OUT A
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
OUT B
OUT C
OUT D
IN B
IN C
IN D
CONNECTION DIAGRAMS Page 27/112
5.9 GEO S12 / NXAMP4x4 (Stereo Active mode)
SP4
SP4
IN A
OUT A
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
SP4
OUT B
OUT C
OUT D
IN B
4 x HF
4 x LF
4 x HF
4 x LF
Page 28/112 GEOSOFT2
6 GEOSOFT2
GEOSoft2 software is a R&D simulation tool derived application. It processes measured speaker data
with complex mathematical algorithms to assist the user in designing vertical GEO Tangent Arrays that
provide even SPL throughout the depth of the audience. Due to the complexity of the interaction of
multiple cabinets, it is simply not possible to reliably design curved vertical arrays without using the
processing power of a computer to predict the optimum array structure for a given audience geometry.
The design logic is far more complex than looking at a section drawing of the venue, measuring the
overall angle needed to cover the audience from the cluster location, and dividing by 10 degrees to
determine the required amount number of GEO S1210 cabinets.
GEOSoft2 is an easy to use tool that allows to shape the energy leaving the cluster to fit the audience. It
predicts pressure levels radiated from the system to ensure enough cabinets are provided for the
application, as well as mechanical constraints for safe flown systems.
In addition, it provides mechanical information for all clusters in agreement with Structural Analysis
Reports (available in the Help section): dimensions, weight, gravity center position, forces, moments,
working load and safety factor.
GEOS8, GEOT and GEOD Structural Analysis Reports have been validated by German Certification
Organization RWTUV systems GmbH.
Geo S12 Structural Analysis Report is currently being examined by German Certification Organization
RWTUV systems GmbH.
Geosoft2 installation package includes all GEO User Manuals, Structural Analysis Reports and
Certificates PDF files (which can be found in the last section of User Manuals).
Geosoft2 is a freeware downloadable on www.nexo-sa.com. Please check our website
periodically for upgrades.
IMPORTANT
Never install a GEO S12 cluster without checking its acoustical performances and
mechanical safety in Geosoft2 prior to installation.
Any question or bug report please contact [email protected]
GEOSOFT2 ACOUSTIC PAGE
CONFIGURABLE DIRECTIVITY DEVICE Page 29/112
7 CONFIGURABLE DIRECTIVITY DEVICE
The GEO Wavesource controls dispersion of acoustic energy using an hyperboloid acoustical reflector
in the “coupling plane” (the vertical plane of a curved vertical tangent array) and a diffraction slot in the
“non-coupling plane” (the horizontal plane of a curved vertical tangent array). The patented
Configurable Directivity Device consists of bolt-on flanges that alter the diffraction slot’s exit flare rate.
7.1 Installing & removing GEO’s Configurable Directivity flanges
GEO S12 are shipped in the 80° dispersion configuration;
120° flanges is an optional accessory.
To change dispersion in the non-coupling plane to 120°:
Remove the front grill (drawings below);
Remove the three TORX (5x25) screws per flange on each side of the GEO Waveguide
(drawings below);
Install the 120° flanges with the six TORX screws
Re-install the grid, being careful that the NEXO logo must be on the 12” loudspeaker side.
REMOVING THE GRILL
REMOVING THE SCREWS REPLACING THE FLANGES
Page 30/112 CONFIGURABLE DIRECTIVITY DEVICE
7.2 When & where to use Configurable Directivity flanges
The diagrams show audience area coverage for a stereo system. While the GEO cluster will deliver
even SPL from the front to the rear of this audience area, there are “holes” near the front in the centre
and at the outside edges. We cannot fill the outside coverage gaps without enlarging the centre gap,
and vice versa (left figure below).
If 120° Configurable Directivity Devices are installed at the bottom cabinet of the clusters, coverage will
look more like the pattern in right figure below.
-6dB coverage, all GEO S12 in 80° configuration -6dB coverage, bottom GEO S12 in 120° configuration
In curved vertical arrays, the 120° Configurable Directivity Device can be used:
On the bottom row of curved vertical arrays, to fill in coverage gaps in the front rows.
On all rows of curved vertical arrays, in cases where 120° of horizontal coverage is
preferred to 80°.
Figure below shows isocontour coverage for 80° and 120° configurations.
80° AND 120° CONFIGURATIONS ISOCONTOUR COVERAGE
GEO S12 HARDWARE SETUP PROCEDURE Page 31/112
8 GEO S12 HARDWARE SETUP PROCEDURE
Before proceeding with assembly of GEO S12 arrays, please ensure that the components are present
and undamaged. A component list is appended to this manual. In the event of any shortage, please
contact your supplier.
For maximum efficiency the GEO S12 rigging system requires three experienced persons for set-up:
typically one motor hoist operator, and one GEO S12 operator per side of the array. Good
synchronisation and crosscheck between the operators are key elements for a reliable and safe set-up.
8.1 SAFETY FIRST
GEO S12 Rigging System structural computations and related documents are available in Geosoft2 or
at Nexo ([email protected]) upon request.
We include this section to remind you of safe practice when flying the GEO S12 system. Please read it
carefully. However, user must always apply his or her knowledge, experience and common sense. If in
any doubt, seek advice from your supplier or NEXO agent.
This manual offers guidance only for GEO S12 loudspeaker systems. References in this manual to
other rigging equipment such as motor hoists, steels, shackles etc. are made to clarify the description of
GEO S12 procedures. The user must ensure that operators are properly trained by other agencies in
the use of these items.
The GEO S12 Rigging System has been optimised for the deployment of curved vertical or horizontal
tangent arrays of GEO S12 loudspeakers. Angle adjustment between cabinets has been limited to
specific settings to ensure correct acoustic coupling.
The GEO S12 Rigging System is a professional precision tool set, and should be handled with extreme
care. Only persons who are fully conversant with the operation of the GEO S12 Rigging System and
provided with suitable safety equipment should deploy GEO Arrays. Misuse of the GEO S12 Rigging
System could lead to dangerous consequences.
Used and maintained correctly, the GEO S12 Rigging System will give many years of reliable service in
portable systems. Please take the time to read and understand this manual. Always use GEOSoft2 to
determine the optimum angle settings for a particular venue, hang point and curved vertical GEO S12
cluster. Applied forces and moments are strongly cabinet quantity and angle configuration dependent.
Cluster configuration must be implemented and validated in Geosoft2 prior to installation.
8.1.1 Flown Systems Safety
Always inspect all the rigging components and cabinets for damage before assembly. Pay
special attention to the lifting points, and safety clips. If you suspect that any of the components
are damaged or defective, DO NOT USE THE AFFECTED PARTS. Contact your supplier for
replacements.
Read this manual carefully. Also be familiar with the manuals and safe working procedures for
any ancillary equipment that will be used with the GEO S12 Rigging System.
Applied forces and moments are strongly cabinet quantity and angle configuration dependent.
Cluster configuration must be implemented and validated in Geosoft2 prior to installation.
Ensure that all local and National regulations regarding the safety and operation of flying
equipment are understood and adhered to. Information on these regulations can usually be
obtained from Local Government Offices.
When deploying a GEO S12 system always wear protective headwear, footwear and eye
protection.
Do not allow inexperienced persons to handle a GEO S12 system. Installation personnel should
be trained in loudspeaker flying techniques and should be fully conversant with this manual.
Ensure that motor hoists, hoist control systems and ancillary rigging components are currently
certified as safe and that they pass a visual inspection prior to use.
Page 32/112 GEO S12 HARDWARE SETUP PROCEDURE
Ensure that public and personnel are not allowed to pass beneath the system during the
installation process. The work area should be isolated from public access.
Never leave the system unattended during the installation process.
Do not place any object, no matter how small or light, on top of the system during the installation
procedure. The object may fall when the system is flown and is likely to cause injury.
Secondary safety steels must be installed once the system has been flown to the operating
height. Secondary steels must be fitted irrespective of requirements of the local safety standards
applicable to the territory.
Ensure that the system is secure and prevented from pivoting around the motor hoist.
Avoid any form of excessive dynamic loading to the assembly (structural computations on GEO
S12 Rigging System are based on a 1/1.2 factor for hoist or motor acceleration).
NEVER attach any item to the GEO S12 system other than the GEO S12 accessories.
When flying outdoor systems ensure that the system is not exposed to excessive wind or snow
loads and is protected from rainfall.
The GEO S12 Rigging System requires regular inspection and testing by a competent test
centre. NEXO recommend that the system is load tested and certified annually or more
frequently if local regulations require.
When de-rigging the system ensure that the same duty of care is given to the procedure as for
the installation. Pack GEO S12 components carefully to prevent damage in transit.
8.1.2 Ground Stacking Safety
Statistically, many more injuries occur due to unstable ground stacked PA systems than those
associated with flown systems. There are several reasons for this fact, however the message is clear:
Always survey the supporting structure upon which a ground stack is to be built. Always look
beneath PA wings to inspect the deck support and if necessary ask for the stage scrims and
dressings be removed to allow access.
If the stage surface slopes, as it does in some theatres, ensure that the system is prevented from
sliding forwards due to vibration. This may require the fitting of timber battens to the stage floor.
For outdoor systems ensure that that the system is protected from wind forces which might
cause the ground stack to become unstable. Wind forces can be huge, especially upon large
systems, and should never be underestimated. Observe meteorological forecasts, calculate the
“worst case” effect upon the system prior to erection and ensure that the system is secured
appropriately.
Take care when stacking cabinets. Always employ safe lifting procedures and never attempt to
build stacks without sufficient personnel and equipment.
Never allow anyone, whether operators, artists or members of the public to climb onto a ground
stacked PA system. Anyone who needs to climb over 2m (6 ft) high should be fitted with suitable
safely equipment including a clip-on harness. Please refer to local Health and Safety legislation in
your territory. Your dealer can help with advice on access to this information.
Apply the same attention to all safety matters when de-stacking systems.
Be aware that safety procedures are as important in the truck and in the warehouse as they are
at the venue.
GEO S12 HARDWARE SETUP PROCEDURE Page 33/112
8.1.3 Contacts
Correct training is fundamental to safe practise when working with loudspeakers flying systems. NEXO
recommend that users contact local industry associations for information on specialist course.
Information for International training agencies can be obtained by contacting either:
The Production Services Association
(PSA),
School Passage,
Kingston-upon-Thames,
KT1 SDU Surrey,
ENGLAND
Telephone: +44 (0) 181 392 0180
Rigstar Training and Testing Center
82 Industrial Dr. Unit 4
Northampton, Massachusetts 01060 U.S.A.
Phone: 413-585-9869 -- Fax: 413-585-9872
ESTA
Entertainment Services & Technology Association
875 Sixth Avenue, Suite 1005
NEW YORK, NY 10001 USA
Phone: 212-244-1505 – Fax: 212-244-1502
- www.esta.org
Page 34/112 GEO S12 HARDWARE SETUP PROCEDURE
8.2 General Description
GEO S1230 GEO S1210
GEO S1230 and GEO S1210 incorporate two connecting plates (one per side) on which a
comprehensive range of accessories can be mounted.
GEO S12 CONNECTING PLATES
There are two families of accessories:
fixed installation accessories, which are designed to be screwed on the connecting plates;
touring accessories, which can be installed or removed with a quick connecting system.
Oblong holes for Touring Applications Accessories
Tapped holes for Fixed Installation Accessories
GEO S12 HARDWARE SETUP PROCEDURE Page 35/112
8.2.1 Described configurations
FIXED INSTALLATIONS
TOURING APPLICATIONS
SECTION 8.3.
2
SECTION 8.3.
2
SECTION 8.3.
3
SECTION 8.3.4
SECTION 8.3.6
SECTION 8.4.9
SECTION 8.4.
2
SECTION 8.4.
3
SECTION 8.4.
5
SECTION 8.4.6
SECTION 8.4.4
SECTION 8.4.
7
SECTION 8.4.8
Page 36/112 GEO S12 HARDWARE SETUP PROCEDURE
8.2.2 WARNINGS ON GEO S12 ACCESSORIES
WARNING 1T
All GEO S12 Accessories are specifically rated in agreement with structural
computations.
Never use other accessories – including push-pins - when assembling GEO S12 cabinets
than the ones provided by NEXO: NEXO will decline responsibility over the entire GEO
S12 accessory range if any component is purchased from different supplier.
WARNING 2
For SAFETY reasons, following first generation accessories:
- GEOS12-XBOW
- GEOS12-TCBRK
- GEOS12-SSBRK
- GEOS12-PSBRK
- GEOS12-TTC
Have been recalled in August 2007 and MUST NO LONGER BE USED
These accessories have been replaced by:
- GEOS12-XBOW-V2
- GEOS12-TCBRK-V2
- GEOS12-SSBRK-V2
- GEOS12-PSBRK-V2
- GEOS12-TTC-V2
Please contact your local distributor if any doubt in relation the GEO S12 accessories you
are using.
WARNING 3
All GEO S12 accessories have been designed so that cabinets are arrayed in the acoustic
coupling plane (adjacent waveguides as shown in figures below).
GEO S12 assemblies in the “non coupling plane as shown in figure below- are UNSAFE
and STRICTLY PROHIBITED.
YES YES NO
GEO S12 HARDWARE SETUP PROCEDURE Page 37/112
8.3 GEO S12 in fixed installations
8.3.1 Fixed installation Accessories and kits
Accessories are:
Bumper (GEOS12-FBUMPER)
“U” Bracket (GEOS12-UBRK)
“L” Bracket for cable suspension (GEOS12-LBRK)
“U” Bracket for rigid suspension (GEOS12-ABRK)
Connecting Plates / range : 0.20° - 3.15° (GEOS12-ANPL1)
Connecting Plates / range : 5.00° - 10.0° (GEOS12-ANPL2)
Connecting Plates / range : 16.0° - 30.0° (GEOS12-ANPL3)
Please refer to section 13.4 of this manual for more information of above references.
IMPORTANT
In order to prevent screws from getting loose in fixed installations, use blocking liquid
LOCTITE
TM
243 or equivalent for all screws used with GEO S12 fixed installation
accessories.
LOCTITE
TM
243 is available at NEXO or at your local distributor upon request.
GEOS12-FBUMPER GEOS12-UBRK GEOS12-LBRK GEOS12-ABRK
GEOS12-ANPL1 GEOS12-ANPL2 GEOS12-ANPL3
Page 38/112 GEO S12 HARDWARE SETUP PROCEDURE
8.3.2 Single GEO S12 rigidly mounted on a wall or a ceiling (vertical or horizontal)
Required items
1 x GEOS12-UBRK (allows all angles to be implemented)
4 x 12mm diameter screws (not provided)
IMPORTANT
Ensure that the surface – wall or ceiling – is strong enough to hold GEO S12 weight and
that the for screws 12mm diameter and corresponding plugs required to fix the “U”
bracket on the wall or under the ceiling are properly dimensioned.
Procedure
For screws 12mm diameter (not provided) are required to secure the “U” Bracket on the wall or
ceiling;
Remove the four TORX screws holding connector plates on both sides of GEO S12;
Fill each screw hole with Locktite 243 or equivalent;
Position the GEO S12 inside the “U” Bracket to desired angle; “U” bracket oblong holes must be
properly aligned with panels holes;
Use the eight screws and washers from GEOS12-UBRK kit to connect “U” bracket to cabinet.
GEO S12 HARDWARE SETUP PROCEDURE Page 39/112
8.3.3 Single GEO S12 cable mounted on a wall or a ceiling (vertical or horizontal)
Required items
1 or 2 x GEOS12-LBRK (allows cable suspension, holes for cable suspension are 10mm
diameter);
2 or 4 slings and corresponding shackles (not provided)
IMPORTANT
Ensure that the ceiling is strong enough to hold GEO S12 weight and that the cable
suspension system required to install the cabinet under the ceiling is properly
dimensioned.
Procedure
Vertical
Remove the four TORX screws holding connector
plate on upper side of GEO S12;
Remove the connector plate from Geo S12;
Fill each screw hole with Locktite 243 or equivalent;
Position external plate from GEOS12-LBRK kit and
secure it using the 2 of the 4 shoulder screws supplied
with this kit;
Position “L” bracket from GEOS12-LBRK kit, and
secure it to the cabinet using the 2 remaining shoulder
screws supplied with this kit.
Slings and shackles (not provided) are required to
secure the cluster under the ceiling;
Horizontal
Remove the four TORX screws holding connector
plates on both side of GEO S12;
Remove the connector plates from Geo S12;
Fill each screw hole with Locktite 243 or equivalent;
Position external plates from GEOS12-LBRK kits and
secure them using the shoulder screws supplied with
these kits;
Position “L” brackets from GEOS12-LBRK kits, and
secure them to the cabinet using the 4 remaining
shoulder screws supplied with these kits.
Slings and shackles (not provided) are required to
secure the cluster under the ceiling;
Page 40/112 GEO S12 HARDWARE SETUP PROCEDURE
8.3.4 GEO S12 vertical array rigidly mounted on a ceiling
Required items
1 x GEOS12-FBUMPER (allows +/-5° bumper tilt when installed below a flat surface; if higher
bumper tilt is required, surface will have to be defined accordingly) ;
(N-1) x GEOS12-ANPL for a N x GEO S12 array (ANPL1 ranges from 0.2° to 3.15°, ANPL2
ranges from 5° to 10°, ANPL3 ranges from 16° to 30°)
Four 12mm diameter screws (not provided)
IMPORTANT
Ensure that the ceiling is strong enough to hold GEO S12 cluster weight and that the four
screws 12mm diameter and corresponding plugs required to fix the bumper under the
ceiling are properly dimensioned.
Procedure
(1) Set all GEO S12 side by side;
(2) Remove the four TORX screws holding connector plates on upper side of all GEO S12’s;
(3) Remove the connector plates from all Geo S12’s;
(4) Fill each screw hole with Locktite 243 or equivalent;
(5) Position bottom external plates, angle plates and top external plate from GEOS12-ANPL kit to
required inter-cabinet angle value between cabinets upper sides;
(6) Screw all shoulder screws from GEOS12-ANPL kits so that all plates and cabinets are
tightened together;
GEO S12 HARDWARE SETUP PROCEDURE Page 41/112
(7) Flip the cluster upside down to access connector plates located on the down side;
(8) Repeat all above steps from #2 to #6;
(9) Position the GEOS12-FBUMPER bumper to required angle position and use the four
shoulder screws from GEOS12-FBUMPER kit to connect it the bumper to the top cabinet;
(10) Flip GEO S12 cluster by 90° so that it is ready to be positioned under the ceiling;
(11) Four screws 12mm diameter (not provided) are required to secure the bumper under the
ceiling.
Page 42/112 GEO S12 HARDWARE SETUP PROCEDURE
8.3.5 GEO S12 vertical array cable mounted on a ceiling
Required items
1 x GEOS12-FBUMPER;
2 x GEO S12-LBRK (allows cable suspension for bumper, holes for cable suspension are 10mm
diameter);
(N-1) x GEOS12-ANPL for a N x GEO S12 array (ANPL1 ranges from 0.2° to 3.15°, ANPL2
ranges from 5° to 10°, ANPL3 ranges from 16° to 30°)
4 slings and shackles (not provided)
IMPORTANT
Ensure that the ceiling is strong enough to hold GEO S12 cluster weight and that the
cables suspension system required fixing the bumper under the ceiling is properly
dimensioned.
Procedure
Connect the bumper and the two “L” brackets using the screws, washers and bolts provided in
the GEO S12-LBRK kit;
Proceed as in preceding section;
4 slings and 4 shackle (not provided) are required to secure the cluster under the ceiling;
GEO S12 HARDWARE SETUP PROCEDURE Page 43/112
8.3.6 GEO S12 horizontal array rigidly mounted on a ceiling
Required items
2 x GEO S12-ABRK (allows rigid ceiling suspension for horizontal arrays)
(N-1) x GEOS12-ANPL for a N x GEO S12 array (ANPL1 ranges from 0.2° to 3.15°, ANPL2
ranges from 5° to 10°, ANPL3 ranges from 16° to 30°)
Four 12mm diameter screws (not provided)
IMPORTANT
Ensure that the ceiling is strong enough to hold GEO S12 cluster weight and that the four
screws 12mm diameter and corresponding plugs required to fix the “L” brackets under
the ceiling are properly dimensioned.
Procedure
(1) Set all GEO S12 side by side;
(2) Remove the four TORX screws holding connector plates on upper side of all GEO S12’s;
(3) Remove the connector plates from all Geo S12’s;
(4) Fill each screw hole with Locktite 243 or equivalent;
(5) Position bottom external plates, angle plates and top external plate from GEOS12-ANPL kit to
required inter-cabinet angle value between cabinets upper sides;
(6) Screw all shoulder screws from GEOS12-ANPL kits so that all plates and cabinets are
tightened together;
Page 44/112 GEO S12 HARDWARE SETUP PROCEDURE
(7) Flip the cluster upside down to access connector plates located on the down side;
(8) Repeat all above steps from #2 to #6;
(9) Position the two “U” brackets from GEOS12-ABRK kits on the outer cabinets next the angle
plates, and tight them to the cabinets using the shoulder screws provided with these kits,
(10) Four screws 12mm diameter (not provided) are required to secure the “U” brackets under
the ceiling;
GEO S12 HARDWARE SETUP PROCEDURE Page 45/112
8.3.7 GEO S12 horizontal array cable mounted on a ceiling
Required items
2 x GEO S12-LBRK (allows cable suspension for horizontal arrays, holes for cable suspension
are 10mm diameter);
(N-1) x GEOS12-ANPL for a N x GEO S12 array (ANPL1 ranges from 0.2° to 3.15°, ANPL2
ranges from 5° to 10°, ANPL3 ranges from 16° to 30°)
4 slings and 4 shackles (not provided).
IMPORTANT
Ensure that the ceiling is strong enough to hold GEO S12 cluster weight and that the
cables suspension system required fixing the cluster under the ceiling is properly
dimensioned.
Procedure
Proceed as in above section, GEOS12-LBRK being positioned on the outer cabinets instead of
GEOS12-ABRK.
4 slings and 4 shackle (not provided) are required to secure the cluster under the ceiling;
Page 46/112 GEO S12 HARDWARE SETUP PROCEDURE
8.4 GEO S12 in touring applications
8.4.1 Touring Accessories
Accessories are :
Bumper (GEOS12-BUMPER)
Rigging Plates (GEOS12-XBOW-V2)
Tension Mode Link Bars for GEOS12-XBOW-V2 (GEOS12-TLB)
Lifting Ring for GEOS12-SSBRK, GEOS12-PSBRK or GEOS12-TTC (GEOS12-XHBRK)
Truss hook for GEOS12-SSBRK, GEOS12-PSBRK or GEOS12-TTC (GEOS12-TCBRK-V2)
“U” Bracket for single horizontal GEO S12 on pole stand, lifting ring or truss hook (GEOS12-
SSBRK-V2)
U” Bracket for two horizontal GEO S12 on pole stand, lifting ring or truss hook (GEOS12-
PSBRK-V2)
Flying Bar for single vertical GEO S12 (GEOS12-TTC-V2)
Ground Stacking device for up to 6 GEOS1210 (GEOS12-GSTK)
Please refer to section 13.3 of this manual for more information of above references.
GEOS12- BUMPER GEOS12-XBOW-V2
GEOS12-TLB GEOS12-XHBRK GEOS12-TCBRK-V2
GEOS12-SSBRK-V2 GEOS12-PSBRK-V2
GEOS12-TTC-V2 GEOS12-GSTK
GEO S12 HARDWARE SETUP PROCEDURE Page 47/112
R > H
H
8.4.2 Single GEO S12 on speaker stand or on RS15 horizontally
Required items
1 x “U” Bracket for single horizontal GEO S12 (GEOS12-SSBRK-V2);
1 x Speaker stand diameter 35mm (K&M 213 or equivalent);
Or NEXO PS pole stand (STDPS) for mounting on top of RS15
IMPORTANT (SPEAKER STAND)
- Speaker stand must be rated for assembly weight (40kg rated load min);
- Speaker stand must always be installed on a horizontal surface;
- Stand height and footprint must be defined to prevent assembly from collapsing;
- Ensure that public is not allowed within a safety area which radius is equal or higher
than assembly height.
IMPORTANT (RS15 POLE STAND)
- NEXO STDPS pole stand only should be used for mounting on top of NEXO RS15
- If 2 RS15s are to be stacked below GEO S12s pole mounted, they should be connected
together through use of RS15 rigging plates;
- RS15s must always be installed on a horizontal surface;
- Ensure that public is not allowed within a safety area which radius is equal or higher
than assembly height.
Procedure
Slide GEOS12-SSBRK-V2 side plates into GEO S12 connecting plate oblong holes;
Lock safety pins into GEO S12 connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12 connecting panels.
Position “U” bracket over these side plates; align centre holes;
Insert adjustment handles, adjust vertical angle and tight the handles to prevent GEO S12 from
rotating around “U” bracket;
Lift assembly on speaker stand or on RS15 with STDPS pole stand.
Page 48/112 GEO S12 HARDWARE SETUP PROCEDURE
GEO S12 HARDWARE SETUP PROCEDURE Page 49/112
8.4.3 Single GEO S12 flown vertically
Required items
1 x Flying Bar for single vertical GEO S12 (GEOS12-TTC-V2)
1 x Lifting Ring (GEOS12-XHBRK)
Or 1 x Truss hook (GEOS12-TCBRK-V2)
IMPORTANT
Ensure that truss suspension point is strong enough to hold GEO S12 weight.
Procedure
Slide flying bar GEOS12-TTC-V2 into GEO S12 connecting plate oblong holes;
Lock safety pin into GEO S12 connecting plate;
IMPORTANT
Ensure that safety pin is properly locked into GEO S12 connecting panel.
Cable suspension:
Connect lifting ring GEOS12-XHBRK to flying bar by inserting 8x45 quick release pin in required
holes for proper vertical aiming;
Ensure lifting ring is properly locked to flying bar;
Connect assembly to suspension point with sling and shackle (not provided).
Truss suspension
Connect truss hook GEOS12-TCBRK-V2 to flying bar by inserting 8x45 quick release pin in
required holes for proper vertical aiming;
Ensure truss hook is properly locked to flying bar;
Lift and position assembly, lock hook on truss suspension point and secure with hook cable.
Page 50/112 GEO S12 HARDWARE SETUP PROCEDURE
8.4.4 Single GEO S12 flown horizontally
Required items
1 x “U” Bracket for single horizontal GEO S12 (GEOS12-SSBRK-V2)
1 x Lifting Ring (GEOS12-XHBRK)
Or 1 x Truss hook (GEOS12-TCBRK-V2)
IMPORTANT
Ensure that suspension point is strong enough to hold GEO S12 weight.
Procedure
Slide GEOS12-SSBRK-V2 side plates into GEO S12 connecting plate oblong holes;
Lock safety pins into GEO S12 connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12 connecting panels.
Position “U” bracket over these side plates; align centre holes;
Insert adjustment handles, adjust vertical angle and tight the handles to prevent GEO S12 from
rotating around “U” bracket;
Cable suspension:
Connect lifting ring GEOS12-XHBRK to “U” bracket by inserting 8x45 quick release pin dedicated
holes;
Ensure lifting ring is properly locked to “U” bracket;
Connect assembly to suspension point with sling and shackle (not provided).
Truss suspension
Connect truss hook GEOS12-TCBRK-V2 to “U” bracket by inserting 8x45 quick release pin in
dedicated holes;
Ensure truss hook is properly locked to “U” bracket;
Lift and position assembly, lock hook on truss suspension point and secure with hook cable.
GEO S12 HARDWARE SETUP PROCEDURE Page 51/112
R > H
H
8.4.5 Two GEO S12 on wind-up stand or on RS15 horizontally
Required items
1 x U” Bracket for two GEO S12 (GEOS12-PSBRK-V2)
1 x Wind Up stand diameter 35mm (Eurotruss ES160 or equivalent);
Or NEXO PS pole stand (STDPS) for mounting on top of RS15
IMPORTANT (WIND UP STAND)
- Wind Up stand must be rated for assembly weight (80kg rated load min);
- Wind Up stand must always be installed on a horizontal surface;
- Stand height and footprint must be defined to prevent assembly from collapsing;
- Ensure that public is not allowed within a safety area which radius is equal or higher
than assembly height.
IMPORTANT (RS15 POLE STAND)
- NEXO STDPS pole stand only should be used for mounting on top of NEXO RS15
- If 2 RS15s are to be stacked below GEO S12s pole mounted, they should be connected
together through use of RS15 rigging plates;
- RS15s must always be installed on a horizontal surface;
- Ensure that public is not allowed within a safety area which radius is equal or higher
than assembly height.
Procedure
Set the 2 GEO S12 next to each other front grid to the floor
Slide GEOS12-PSBRK-V2 side plates into GEO S12s connecting plate oblong holes;
Lock safety pins into GEO S12s connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12s connecting panels.
Adjust inter-cabinet angle and lock to required angle value with 8x20quick release pins;
Position “U” bracket over these side plates; align centre holes;
Insert adjustment handles, adjust vertical angle and tight the handles to prevent GEO S12s from
rotating around “U” bracket;
Lift assembly on Wind Up stand or on RS15 with STDPS pole stand.
Page 52/112 GEO S12 HARDWARE SETUP PROCEDURE
GEO S12 HARDWARE SETUP PROCEDURE Page 53/112
Alternative Procedure (“Walder” procedure)
Below described procedure required 2 additional 8x20 quick release pins (BLGEOS)
Split the GEOS12-PSBRK-V2 side plates by removing screws and bolt;
Slide GEOS12-PSBRK-V2 lower half-plates into lower GEO S12 connecting plate oblong holes;
Lock safety pins into lower GEO S12 connecting plate;
Position “U” bracket over these lower half plates; align centre holes;
Insert adjustment handles, adjust vertical angle and tight the handles to prevent GEO S12 from
rotating around “U” bracket;
Lift assembly on Wind Up stand or on RS15 with STDPS pole stand.
Slide GEOS12-PSBRK-V2 upper half-plates into upper GEO S12 connecting plate oblong holes;
Lock safety pins into upper GEO S12 connecting plate;
Lift upper GEO S12 on top of lower one, and connect them together by inserting 8x20 quick
release pins in articulation holes;
Adjust inter-cabinet angle and lock to required angle value with quick release pins.
IMPORTANT
Ensure that safety pins are properly locked into GEO S12 connecting panels.
Page 54/112 GEO S12 HARDWARE SETUP PROCEDURE
DOWN CABINET
UP CABINET
GEO S12 HARDWARE SETUP PROCEDURE Page 55/112
8.4.6 Two GEO S12 flown horizontally
Required items
1 x “U” Bracket for two GEO S12s (GEOS12-PSBRK-V2)
1 x Lifting Ring (GEOS12-XHBRK)
Or 1 x Truss hook (GEOS12-TCBRK-V2)
IMPORTANT
Ensure that suspension point is strong enough to hold two GEO S12s weight.
Procedure
Slide GEOS12-PSBRK-V2 side plates into GEO S12s connecting plate oblong holes;
Lock safety pins into GEO S12s connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12s connecting panels.
Adjust inter-cabinet angle and lock to required angle value with 8x20 quick release pins;
Position “U” bracket over these side plates; align centre holes;
Insert adjustment handles, adjust vertical angle and tight the handles to prevent GEO S12s from
rotating around “U” bracket;
Cable suspension:
Connect lifting ring GEOS12-XHBRK to “U” bracket by inserting 8x45 quick release pin dedicated
holes;
Ensure lifting ring is properly locked to “U” bracket;
Connect assembly to suspension point with sling and shackle (not provided).
Truss suspension
Connect truss hook GEOS12-TCBRK-V2 to “U” bracket by inserting 8x45 quick release pin in
dedicated holes;
Ensure truss hook is properly locked to “U” bracket;
Lift and position assembly, lock hook on truss suspension point and secure with hook cable.
Page 56/112 GEO S12 HARDWARE SETUP PROCEDURE
3.15°
2.0°
1.25°
0.8°
0.5°
0.315°
0.2°
5.0°
6.3°
8.0°
10.0°
L
I
F
T
16.0°
22.5°
30.0°
L
I
F
T
CAUTION: ENSURE ALL PINS
ARE PROPERLY LOCKED
PROFESSIONAL EQUIPMENT !
Please refer to User Manual for Working
Load Limits (WLL) and Rigging
Instructions.
WARNING
Disregard of Rigging Instructions and/or
WLL may damage equipment and risk
personal injury or death.
S
A
F
E
T
Y
P
I
N
M
U
S
T
B
E
F
I
T
T
E
D
8.4.7 Two or more GEO S12 flown vertically
Required items
N Pair of Rigging Plates (GEOS12-XBOW-V2) for N cabinets;
1 lifting ring (GEOS12-XHBRK) every two GEO S12;
4xN Quick release pins for N cabinets;
Properly rated slings, shackles, hoists… (not provided)
IMPORTANT
Lifting ring GEOS12-XHBRK and truss hook GEOS12-TCBRK-V2 are rated for a maximum
of 2 GEO S12s;
Ensure that suspension points are rated accordingly.
Procedure
Insert GEOS12-XBOW-V2 into connecting plates of both sides of the cabinet;
Lock safety pins into GEO S12s connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12s connecting panels.
GEO S12 HARDWARE SETUP PROCEDURE Page 57/112
IMPORTANT
GEO S12 can be flown “Up” or “Down” :
- “Up” means Nexo logo on front grid is at the top;
- “Down” means Nexo logo on front grid is at the bottom.
GEO S12 can be connected “Up” or “Down” by simply flipping the cabinets.
Whenever possible, NEXO recommends symmetrical designs (ie Nexo logo in the same
position on Left and Right clusters for stereo designs)
Connect second Geo S12 with X-Bow front articulation holes and rear link bars and ensure quick
release pins are properly locked;
Repeat above steps for subsequent GEO S12’s;
IMPORTANT
Ensure angle settings are identical on upper and lower side of the cabinets
Ensure that safety pins are properly locked into GEO S12s connecting panels.
Ensure that all quick release pins are properly locked into their position.
Connect lifting rings to “U” bracket with 8x45 quick release pins supplied with GEOS12-XHBRK;
ensure quick release pin is properly locked;
Page 58/112 GEO S12 HARDWARE SETUP PROCEDURE
Lift and position assembly, connect lifting rings to suspension points with sling and shackle;
Secure assembly with secondary safety steel.
IMPORTANT
The requirements for secondary safety systems vary with territories. However, the
secondary safety steel MUST have a SWL equivalent or greater than that of the rigging
system.
GEO S12 HARDWARE SETUP PROCEDURE Page 59/112
8.4.8 Three or more GEO S12 flown horizontally
Required items
1 x Bumper (GEOS12-BUMPER);
N Pair of Rigging Plates (GEOS12-XBOW-V2) for N cabinets;
4xN Quick release pins for N cabinets;
1 hoist (not provided).
IMPORTANT
Maximum GEO S12 quantity for flown vertical cluster is 12 (and eventually less).
Please check Geosoft2 for mechanical Safety Working Load computations.
IMPORTANT
Motor hoist must be rated to support entire cluster weight. Please check configuration
in Geosoft2 for proper motor hoist rating
GEO S12 XBOW ANGLE SETTINGS PLATE
Optional GEOS12-TLB link bar for GEO S12 XBOW
GEOS12-XBOW-V2s are delivered with standard link bars which allow both stacked and flown setups.
However, these link bars require perfect alignment of angle setting holes when adding cabinets.
GEO S12 X-BOW STANDARD LINK BAR
3.15°
2.0°
1.25°
0.8°
0.5°
0.315°
0.2°
5.0°
6.3°
8.0°
10.0°
L
I
F
T
16.0°
22.5°
30.0°
L
I
F
T
CAUTION: ENSURE ALL PINS
ARE PROPERLY LOCKED
PROFESSIONAL EQUIPMENT !
Please refer to User Manual for Working
Load Limits (WLL) and Rigging
Instructions.
WARNING
Disregard of Rigging Instructions and/or
WLL may damage equipment and risk
personal injury or death.
S
A
F
E
T
Y
P
I
N
M
U
S
T
B
E
F
I
T
T
E
D
Page 60/112 GEO S12 HARDWARE SETUP PROCEDURE
To facilitate flying operation, an optional link bar with oblong holes (GEOS12-TLB, pair of link bars
provided with two 8x20 quick release pin) is available in the GEO S12 accessory range.
GEO S12 X-BOW OPTIONAL GEOS12-TLB LINK BAR
To install GEOS12-TLB, remove the standard link as well as nut, screw and washers.
When using GEO S12 XBOW for flown setups, insert pins in the oblong hole and opposite circular hole.
REMOVING STANDARD LINK BAR INSERTING PIN - FLOWN SETUPS
Procedure
Insert GEOS12-XBOW-V2 into connecting plates of both sides of the cabinet;
Lock safety pins into GEO S12s connecting plate
GEO S12 HARDWARE SETUP PROCEDURE Page 61/112
051015 -5 -10
-15
IMPORTANT
Ensure that safety pins are properly locked into GEO S12s connecting panels.
IMPORTANT
GEO S12 can be flown “Left” or “Right” :
- “Left” means Nexo logo on front grid is left as seen from front;
- “Right” means Nexo logo on front grid is right as seen from front.
GEO S12 can be connected to bumper “Left” or “Right” by simply flipping the cabinets.
Whenever possible, NEXO recommends symmetrical designs (preferably NEXO logo
outwards in stereo configurations)
Connect bumper to first GEO S12 using “lift” points of GEO S12 X-Bows; ensure quick release
pins are properly locked;
Insert axis in bumper Geosoft2 predefined hole and secure it with provided “R” clip;
NB: Bumper holes are numbered #-17 to #17, please refer to Geosoft2 to determine axis
position in relation to bumper angle requirements.
If bumper is flown with 2 hoists, then they should be connected to holes #-17 and #17.
Connect hoist hook to bumper axis and lift assembly to sufficient height in order to connect a
second GEO S12;
Connect second Geo S12 with X-Bow front articulation holes and rear link bars and ensure quick
release pins are properly locked;
Repeat above steps for subsequent GEO S12’s
Page 62/112 GEO S12 HARDWARE SETUP PROCEDURE
IMPORTANT
Ensure angle settings are identical on both sides of the cabinets.
Ensure that safety pins are properly locked into GEO S12s connecting panels.
Ensure that all quick release pins are properly locked into their position.
Lift cluster to Geosoft2 defined rigging height, secure cluster horizontally to prevent it from
rotating;
Secure bumper with secondary safety steel.
IMPORTANT
The requirements for secondary safety systems vary with territories. However, the
secondary safety steel MUST have a SWL equivalent or greater than that of the rigging
system.
GEO S12 HARDWARE SETUP PROCEDURE Page 63/112
8.4.9 Ground stacked GEO S1210
Required items
N Pair of Rigging Plates (GEOS12-XBOW-V2) for N cabinets;
1 ground stack device (GEOS12-GSTK);
4xN Quick release pins for N cabinets;
IMPORTANT
- Ground stack device GEOS12-GSTK is rated for a maximum of 6 GEO S1210s in any inter
cabinet angle configuration, provided this device is assembled according to below rules.
- Ground stack device GEOS12-GSTK must always be installed on a horizontal surface;
- Bottom GEO S12 tilt angle must be limited to +/-10°
- Ensure that public is not allowed within a safety area which radius is equal or higher
than assembly height.
Optional GEOS12-TLB link bar for GEO S12 XBOW
GEOS12-XBOW-V2s are delivered with standard link bars which allow both stacked and flown setups.
However, these link bars require perfect alignment of angle setting holes when adding cabinets.
GEO S12 X-BOW STANDARD LINK BAR
To facilitate flying and stacked operation, an optional link bar with oblong holes (GEOS12-TLB, pair of
link bars provided with two 8x20 quick release pin) is available in the GEO S12 accessory range.
GEO S12 X-BOW OPTIONAL GEOS12-TLB LINK BAR
To install GEOS12-TLB, remove the standard link as well as nut, screw and washers.
When using GEO S12 XBOW for stacked setups, insert pins in the two circular holes.
REMOVING STANDARD LINK BAR INSERTING PINS - STACKED SETUPS
Page 64/112 GEO S12 HARDWARE SETUP PROCEDURE
-5˚
+5˚
GEO S12 ground stack device description
GEOS12-GSTK ground stack device includes:
two supporting beams, which support assembly weight;
two connecting beam, which allow connection of the beams to the first cabinet;
one reinforcement beam, to rigidify ground stack device sideways;
Axis, “R” clips and handles to assemble the ground stack device
Procedure
Assemble the two connecting beam and the reinforcement beam with the handles;
Depending on tilt angle – negative, null or positive - to be achieved, there are three positions to
connect above assembly to the supporting beams; below drawings detail these configurations:
Connect the reinforcement bar to the supporting beams according to required tilt angle
configuration using 2 axis per side; secure the axis with provided “R” clips;
GEO S12 HARDWARE SETUP PROCEDURE Page 65/112
Insert GEOS12-XBOW-V2 into connecting plates of both sides GEO S12s;
Lock safety pins into GEO S12s connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12s connecting panels.
Connect bottom GEO S12 to GEO S12 Ground stacking device with 4 8x20 quick release pins;
Connect second Geo S12 with X-Bow front articulation holes and rear link bars and ensure quick
release pins are properly locked;
Repeat above steps for subsequent GEO S12’s
Once the assembly is completed, rotate rear or front GEO S12 ground stack device adjustable
legs to definitive tilt angle, ensuring that +/-10° is never exceeded on bottom GEO S12.
Page 66/112 GEO S12 HARDWARE SETUP PROCEDURE
GEO S12 HARDWARE SETUP PROCEDURE Page 67/112
8.5 Testing and Maintenance of the system
General: Geo is a precision piece of equipment and requires regular attention to maintenance in
order to give long and reliable service. NEXO recommends regular testing of loudspeaker rigging
components, preferably using a suitable test rig coupled with a visual inspection.
Fasteners: there are several critical points in the GEO S12 cabinets.
Of primary concern are:
a) The grid screws attaching the grid to the cabinet
b) The machine screws attaching the connecting plates to the cabinet.
c) The screws attaching the directivity flanges to the front of the cabinet.
These fasteners should be regularly checked and tightened as necessary.
Cleaning: The exterior of the cabinet and the rigging system can be cleaned with a damp cloth
soaked in mild soapy water. On no account use solvent based cleaners , which may damage the
finish of the cabinet
After cleaning, the rigging system must be treated with a suitable lubricant to prevent rusting.
NEXO recommends the use of Scottoil FS365 which is a water-based lubricant with a mixture of
machine oil, surfactant and anti-rust treatment.
Page 68/112 NEXO ANALOGUE GEO S12TD CONTROLLER
9 NEXO ANALOGUE GEO S12TD CONTROLLER
9.1 Analogue TDcontroller Declaration of conformity
This equipment has been tested and found to comply with the safety objectives and essential
requirements of European (73/23/EEC and 89/336/EEC directives) and international Standards, by
fulfilling the requirements of the following harmonized standards:
Electrical Safety (EU) : IEC 60065 (12/2001) Audio, video and similar electronic apparatus
Electrical Safety (US) : UL60065 Seventh Edition, dated June 30, 2003 category AZSQ, E241312.
Electrical Safety (CAN) : CSA-C22.2 N°60065:03 Edition, dated April 2003 category AZSQ7, E241312
Electrical Safety (Rest of the World) : CB test certificate DK-8371 based on IEC60065-2001 7nd ed.
with all national deviations.
Radiated Emission (EU) : EN55103-1 (1996) Electromagnetic compatibility - Product family standard for
audio, video, audio-visual and entertainment lighting control apparatus for professional use.
Radiated Emission (US) : FFC part15 class B
Radiated Emission (CAN) : This Class B digital apparatus complies with Canadian ICES-003.
RF Immunity (EU) : EN55103-2 (1996) Electromagnetic compatibility - Product family standard for
audio, video, audio-visual and entertainment lighting control apparatus for professional use.
Note: EMC conformance testing is based on the use of recommended cable types. The use of other
cable types may degrade EMC performances.
9.2 IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet. (US market)
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
13) Unplug this apparatus during lightning storms or when unused for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
Information about products that generate electrical noise :
NOTE: The United States Federal Communications Commission (in 47 CFR 15.105)
has specified that the following notice be brought to the attention of users of this
product:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The user may find the following booklet, prepared by the Federal Communications
Commission, helpful: How to identify and Resolve Radio/TV Interference Problems.
This booklet is available from the U.S. Government Printing Office, Washington,
D.C. 20402, Stock No. 004-000-00345-4. Use of a shielded cable is required to
comply within Class B limits of Part 15 of FCC Rules. Pursuant to Part 15.21 of the
FCC Rules, any changes or modifications to this equipment not expressly approved by
NEXO S.A. may cause, harmful interference and void the FCC authorization to
operate this equipment.
10CE
A
udio Equi
p
10CE
A
udio Equi
p
NEXO ANALOGUE GEO S12TD CONTROLLER Page 69/112
To avoid electrical shock, do not remove covers.
Dangerous voltages exist inside.
Refer all servicing to qualified personnel only.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
The lightning flash with arrowhead
symbol, within an equilateral triangle
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and
maintenance (servicing) instructions
in the literature accompanying
the appliance.
WARNING ! THIS APPLIANCE CLASS 1 APPARATUS AND MUST BE EATHED.
The green and yellow wire of the mains cord must always be connected to an
installation safety earth or ground. The earth is essential for personal safety as well as
the correct operation of the system, and is internally connected to all exposed metal
surfaces. Additional recommendation for interconnection to other equipment can be
found in the “Analogue TDcontroller Setting-Up Advice” section.
9.3 Analogue TDcontroller Setting-Up Advice
9.3.1 Mains Power
NEXO TDcontrollers don’t provide a mean to switch off the unit from the front panel. As they are
intended to be rack mounted the back panel is not accessible during use. Therefore it is left to the user
to provide a disconnection mean readily operable.
9.3.2 Voltage setting
NEXO TDcontrollers use a switch mode power supply (SMS12). This SMS12 accepts universal AC
power input voltages in the range 90V to 264V, and requires no manual adjustment for voltages in this
range.
9.3.3 Mounting the TDcontroller in a rack (Grounding, shielding & safety issues)
The TDcontroller is intended for rack mounting. The only accessible part during use shall be the front
panel of the TDcontroller. Any space above or under the TDcontroller shall be obstructed with a blank
panel.
The rack is a free grounding and shielding structure and it provides extra shielding. Therefore, it is
desirable that the screws used to fix the TDcontroller in the frame or rack provide an electrical contact
between the chassis of the TDcontroller and the rack.
The primary reason for grounding is safety. Conformance to the applicable requirements of the
authorities having jurisdiction is, of course, mandatory. However, grounding also has an impact on
electromagnetic compatibility. From the EMC point of view, it is desirable to have a low impedance
ground network, as a current flowing in the ground network will then produce low voltage in the network.
A low impedance network can be obtained using a multipoint ground scheme, with as many closed
ground looS12 as is economically possible.
9.3.4 Fuse
The fuse provided in the unit will not blow during normal operation. If the fuse blows the
TDcontroller has malfunctioned. This fuse must only be changed by NEXO certified
service personnel. In any case do not replace the fuse with a non-certified NEXO fuse, as
this will invalidate the NEXO warranty.
Page 70/112 NEXO ANALOGUE GEO S12TD CONTROLLER
Low Z
123
Low Z
123
TDcontroller
AmplifierMixing Desk
123
123
+-
+-
+-
+-
Low Z
Low Z
PE PE
PE
Safety
Ground
SHIELD
SHIELD
IN OUT
CAUTION!
This servicing instruction is for use by qualified service personnel only. To reduce the
risk of electric shock, do not perform any servicing other than that contained in the
operating instructions unless you are qualified to do so.
9.3.5 Recommendations for wiring the sense lines
The impedance of the sense inputs of the TDcontroller are high, so currents are low and therefore light
duty cable can be used. If the TDcontroller is housed in the amplifier racks an unshielded cable may be
used.
If the TDcontroller is located remotely - at the mixing position - a shielded cable is recommended,
without using the shield as a conductor. The cable must be well protected from public access, as it
carries potentially dangerous amplifier voltage.
When one of the channels is not being used and the corresponding sense line is disconnected, cross
talk onto the inactive sense line may in some cases produce signals capable of causing the inadvertent
illumination of the Sense LED on that channel; although this has no effect on the internal operation of
the TDcontroller, it can be cured by short-circuiting the terminals of the inactive sense line.
9.3.6 Recommendations for wiring the audio outputs
The output stages can drive several amplifiers in parallel; however it is not advisable to work with loads
of less than 1kOhm(and strictly forbidden to drive less than 600Ohms). It is best to check the
impedance characteristics of the amplifier inputs - supplied by the manufacturer - to check how many
amplifier channels can be paralleled. Where precise information is not available (and taking 10kOhm as
the minimum value possible), ten channels in parallel per output is a sensible maximum.
9.3.7 Electromagnetic environments
The emission (this word describes all types of electromagnetic noise radiated by the equipment)
requirements which have been applied to Nexo’s TDcontrollers are the stringent requirements of the
”Commercial and light industrial environment” of the product family EMC standard for emission.
The immunity (this word describes the ability to cope with electromagnetic disturbance generated by
other items and natural phenomena) requirements that we have considered exceed those applicable to
the ”Commercial and light industrial environment” of the product family EMC standard for immunity. In
order to provide a further safety margin, we recommend that you do not operate the TDcontrollers in the
presence of electromagnetic interference exceeding half of the limits found in this standard.
These two EMC standards are those
applicable to pro-audio equipment for the
implementation of the ”EMC directive”.
9.3.8 Analogue signal cables
Analogue signals should be connected to the
input and output ports of the TDcontroller via
shielded twisted pair or starquad cable fitted
with XLR connectors on the TDcontroller side.
We recommend the use of low transfer
impedance cables with a braided shield and a
transfer impedance below 10 m/m. For the
sense inputs, the noise requirements are not
as stringent, and any kind of twisted pair cable
will be adequate.
The TDcontroller is intended to be used with
symmetrical (balanced) sources (for instance a mixer) and symmetrical loads (for instance a power
amplifier (see figure). You can see that the TDcontroller provides a low impedance path between pin 1
of its XLR connectors and its chassis. The TDcontroller can sustain high current in pin 1 without
NEXO ANALOGUE GEO S12TD CONTROLLER Page 71/112
degradation of output noise. We recommend that the sources and loads you use have the same
desirable characteristics.
It is sometimes claimed that connecting cable shield at both ends creates ground looS12, and that the
current flowing in such looS12 will produce noise. This is not the case for most professional audio
equipment. In short, there are two kinds of looS12 in which voltages are present: the looS12 formed by
signal wires, and the looS12 formed by grounded conductors, among which are protective earth
conductors (PE) and signal cable shields.
When a cable shield is grounded at both ends, a loop is closed, and the resulting current causes a
reduction of the voltage induced on signal lines. This effect is what the cable shield is intended to
produce, since this is how it protects your signal from magnetic fields.
If you are using an asymmetrical (unbalanced) source, it is recommended to use a shielded twisted pair
and to connect wire 3 of the cable to the
shield at the source output end (see figure).
This technique prevents noise currents
flowing on the return path of the signal. If
you are using an amplifier with an
asymmetrical (unbalanced) input, it is best to
use a shielded twisted pair, and to connect
wire 3 at the TDcontroller end only, as
shown in Fig. 2. This keeS12 a good
capacitance balance for the signal, however
noise currents flow on the return path of the
signal. (Note that this is only acceptable for a
short cable).
If you are using a symmetrical (balanced)
source or amplifier which is prone to become
noisy when a current of less than 100 mA at
the mains frequency (50 Hz or 60 Hz) is
sourced into pin 1 of its XLR connectors, you might consider opening the ground looS12.
9.4 Analogue TDcontroller USER GUIDE
9.4.1 Read before use
The Analogue TDcontroller is designed to be used with its proper set of speaker cabinet. They are not
interchangeable. Its main functions are:
To optimize the response of the system
When operating with the SubBass system (optional), splitting the stereo (2 channel) signal into 2
frequency bands (S12 main system and SubBass system)
Active protection of the cabinets by dynamic audio signal processing (Temperature and
Displacement servo control)
Reduction of amplifier overload (Peak limiter function)
Analogue TDcontrollers also feature:
Stereo operation (2 independent channels) for the main system
Global switchable output level
Adjustable level on the SubBass channel
Low Z
123
Low Z
123
TDcontroller
AmplifierMixing Desk
123
123
+-
+-
+-
+-
Low Z ?
Low Z ?
?PE
PE
Safety
Ground
SHIELD
SHIELD
0V
IN OUT
Page 72/112 NEXO ANALOGUE GEO S12TD CONTROLLER
High CMRR input stage and High current drive output
Compensation of power compression effects on the system response curve.
The Analogue TDcontroller is designed to be inserted between the Audio source (console, preamplifier,
etc.) and the power amplifier.
9.4.2 Front Panel
Most front panel functions and indicators are located inside 2 distinct windows: left-hand areas relate to
functions and indicators dedicated to the optional Sub-bass section, while right-hand window contains
indicators concerning servo control operation for the S12 cabinets.
For more technical details about servo control operation and internal electronic processing, please refer
to section “TDcontroller REFERENCE GUIDE.” Page 74.
Turning the LS channel Overlap / Crossover
Pushing the CONFIGURE button
modifies the high pass filtering. It
does not affect the sub output, which
will always be a filtered sub signal.
(This is therefore not a Sub on/off
button). In the « Overlap » position,
the S12 is exploited to its maximum
capability.
This position should be used if the system is being used without a Subbass. It can also be used with the
Subbass; In this case, there will be a boost in the crossover area. The « Cross over » position is
generally recommended when using the Subbass.
Adjusting the Subbass level (Sub Level)
The potentiometer adjusts the level of the
Subbass channel, a range of 12 dB allows a
variety of configurations and application
conditions to be accommodated. Center
position of the knob is calibrated for 1
Subbass used with 2 distant S12.
Amplifier & Protection indicator
The bicolor green/red AMP LED indicates signal
presence at the sense input of the concerned
channel, allowing visual confirmation of the return
connection of the Sense cables from the amplifier
output. The LED is flashing red, when the Peak
limiter is acting, reducing excessive peak voltage
or levels capable of overloading the channel
amplifier.
The yellow VLF LED indicates that displacement protection for the Subbass are engaged on the
SubBass channel. The temperature protection is not monitored.
On each side of the S12 main system window, yellow TEMP and DISP LEDs indicate when
protection has been activated (temperature or displacement control) for the LF (the HF drivers
temperature protection is not monitored).
Peak Limiter adjustments
The Analogue TDcontroller features two independent peak limiter trims (one for the LSsub amplifier
section, one for the S12 amplifier section), which allows the peak limiter to be set to limit the maximum
power of the amp (without affecting the protections threshold). The peak limiter has no real cabinet
protection functions; it must be tuned to avoid overdriving the amp that in turn can generate obvious
clipping noise.
NEXO ANALOGUE GEO S12TD CONTROLLER Page 73/112
To set the peak limiter to the correct value, either turn the trimmer clockwise until the red LED lights at
the same time as the amp’s clipping LED, or use the graduation (power value given for 8load).
9.4.3 Rear Panel
Audio Inputs
The audio inputs are two 3-pin female XLR connectors located in the area labeled BALANCED
INPUTS. Signal is applied between pins 2 and 3, pin 1 is connected to ground. When the Controller is
linked to a signal source with balanced outputs, the XLR connections are simply wired pin to pin (1 to
1, etc.). As a result of the balanced nature of the outputs (and providing that balancing is respected by
way of the connection to the amplifier), there is no hot or cold pin - the Analogue TDcontroller being
neutral regarding the polarity of the signal.
Output Level Switch
The 3-position output level switch is used to match the processor gain to the amplifier gain for
optimum signal to noise ratio. The three gain values available are +6, 0 or -6 dB. For minimum noise
floor the -6dB setting should be chosen, for maximum headroom the +6dB position should be used.
Audio Outputs
The audio outputs are the three 3-pin male XLRs located in the area labeled BALANCED OUTPUTS.
The channel corresponding to each output connector is identified by the labels Left, Right and Sub
L+R (mono SubBass).
Signal is applied between pins 2 and 3, pin 1 is connected to ground.
When used with an amplifier with balanced inputs, the wiring of the output XLR is simply pin to pin (1
to 1, etc.), the polarity of the signal being preserved if the source connected to the input is also
balanced (see previous section).
Sense inputs
The sense inputs of the three channels (left, right and SUB) are arranged on
a six-pole barrier strip set into the rear panel within the area labeled SENSE
INPUT. The Sense inputs are intended for connection to the output signals of
the amplifiers driving one cabinet of each the channels being used.
Connection is made via the female part - removable - of the connector
(supplied with the Controller) as outlined below:
Channel Amplifier Output Terminal Barrier strip connector
S12 Left - (black)
Ö
pin 1 (figure)
+ (red)
Ö
pin 2
S12 Right - (black)
Ö
pin 3
+ (red)
Ö
pin 4
RS15 - (black)
Ö
pin 5
+ (red)
Ö
pin 6
Input sense connection MANDATORY for proper operation of the servo-control system, the cabinets
will NOT BE PROTECTED if the sense lines are unconnected.
Earth Lift
The push button labeled « Earth Lift » allows connection
(depressed position), or disconnection (out position)
between the signal ground and the mains earth, which is
itself linked to the chassis. Using this button may help to
eliminate hum due to ground looS12 created in the
system.
Sub jumper
In certain applications you may wish to disable the mono summation (but keep the 6dB gain boost) on
the sub channel. By moving the internal jumper ST1 inside the unit, the sub channel will only use the
Right input (with 6dB gain to keep the same sub level when the mono summation is enabled).
BALANCED INPUTS
RIGHT LEFTRIGHT LEFTSUB L+R
OUPUT
LEVEL
+6dB
0dB
-6dB
BALANCED OUTPUTS
EARTH
LIFT
115-230V 50-60Hz 10W
CAUTION !
To reduce the risk of electric schock
grounding of the center pin
of this plug must be maintained.
MADE IN FRANCE
+ RIGHT - + LEFT -+ SUB -
SENSE INPUT
(from amp terminals)
CAUTION !
Sense line must be connected
for speaker protection.
10CE
PS8 TDcontroller
s.n: 03105
4004
Page 74/112 NEXO ANALOGUE GEO S12TD CONTROLLER
Always ensure that your TDcontroller is disconnected from main before opening the unit. Remove the 3
screws fastening the top panel. The ST1 jumper is located near the Input XLR. The PIN1 being the PIN
closest of the Input XLR. Strap PIN 1-2 (B in the drawing) in order to drive the sub only from input R.
Strapping Pin 2-3 (labeled A, factory default) will provide the summation of channel R&L.
AB
1
2
3
9.5 TDcontroller REFERENCE GUIDE
9.5.1 Linear section
The characteristics of the linear section are independent of signal level, as opposed to the servo control
functions described in next paragraph.
Subsonic and VHF filtering
Low and high-pass filters are used to remove signals out of the usable frequency range, eliminating
sub- and ultra-sonic components that could possibly degrade the performance of the Controller and
amplifiers. These filters are optimized to realize the overall target system response.
Equalizing acoustical response
This equalization section provides the required correction to obtain a flat system response, as the
cabinets are acoustically designed for maximum efficiency in the whole frequency range. Active rather
than passive attenuation allows amplifier voltages to be lowering for a given output SPL and therefore
increases the maximum SPL achievable with the same amplifier.
Active equalization also extends system bandpass, especially at low frequencies where acoustical
performance is limited by cabinet size.
S12 / Subbass Cross-Over
From input signals summed together, the resulting mono signal is low-pass filtered to feed the SubBass
channel. When the channel is turned on (Subbass On), main channels (Left & Right) high-pass filters
are reconfigured to filter out signal components below the crossover frequency. Slopes and other filter
characteristics are optimized using techniques optimized for the actual acoustical data of each driver.
9.5.2 Servo Control section
Servo control of the S12 TDcontroller is intended to work with amplifier return signals present at the
Sense inputs (monitored by front panel LEDs).
VCAs and VCEQs
Each of the 3 Audio channels (Left, Right and SubBass) contains two voltage controlled elements
driven by servo signals:
One operates on the whole frequency range (wide band VCA).
NEXO ANALOGUE GEO S12TD CONTROLLER Page 75/112
The other elements work selectively as dynamic equalizers (LF-VCEQ & HF-VCEQ).
Depending on the nature and origin of the servo signals, either one or the 3 combined elements is used
to process the Audio signal. This feature allows more efficient processing while reducing audible effects.
Displacement control
The signal from the sense input is fed through a shaping filter producing a signal proportional to the
voice coil displacement. This control signal is compared to a fixed value and if exceeded, the LF-VCEQ
is activated with very short attack time to reduce speaker excursion.
Temperature control
Sense input is fed to a shaping filter to create a voltage proportional to the instantaneous voice-coil
current. The signal is integrated over time to simulate heat buildup in the specific driver. When the
resulting voltage exceeds a preset threshold, the VCA is activated to limit the voice coil temperature
within its safety range. Power compression is also simulated by lowering the high frequencies when
temperature protection is acting on the bass loudspeaker.
Dynamic control
To reduce audible « pumping » effects due to very long time constants of temperature detection signals,
an alternate integration is also processed with a shorter time constant. Whilst anticipating the
temperature protection and reducing its unwanted effects, action of this signal also improves dynamics
control.
Peak Limiter
The above mentioned devices provide reliable protection against potential speaker over-heating and
over-excursion. Nevertheless driving the cabinets at very high peak voltages (with oversized amplifiers)
as well as delivering distorted signals might be dangerous for the speakers. The Peak limiter is both
useful for:
Maintaining good sound quality at high levels (it will reduce amplifier distortion).
Increasing protection reliability (limiting peak voltages to levels that speakers can permanently
withstand, and reducing the occurrence of subsonic signals delivered by overloaded amS12)
Page 76/112 NEXO NX242-ES4 DIGITAL CONTROLLER FOR GEO S12
10 NEXO NX242-ES4 DIGITAL CONTROLLER FOR GEO S12
IMPORTANT
GEO S12 use latest NEXO proprietary sophisticated DSP algorithm, which require
additional resources from the NX-Tension ES4 Card. All available GEO S12 setups require
that NX-ES4 card is installed in NX242 TD Controller.
10.1 NX242 Proprietary Functions
The NX242 is much more than a “generic” Digital Signal Processor. It provides all the standard
functions that you expect from this type of unit, but its real value is the interface between you and your
speaker system. The NX242 includes a number of proprietary functions, developed and refined during
NEXO’s 20 years of loudspeaker development experience, to ensure that your PA delivers maximum
performance and reliability.
10.1.1 Upgradable Firmware
NEXO releases regular firmware updates. Each new release is the result of our ongoing R&D program
combined with user feedback from the field. New firmware releases can include new setups for different
combinations of NEXO full range loudspeakers and subwoofers, improvements to existing setups, and
new software functions. The NX242 is thus evolving with each of those releases, profiting from the
latest discoveries of NEXO’s R&D department as well as the experience of NEXO users.
10.1.2 EQ & Filtering
Subsonic and VHF filtering
Low and high-pass filters are used to filter out frequencies that could possibly degrade the performance
of the TDcontroller and amplifiers. The filters are optimised to work in conjunction with overall system
response.
The high pass filters are also extremely important as they help control excursion at very low
frequencies, which is a major feature for system reliability. This is one of the main reasons to avoid
using setups which are not designed for the cabinet you are using.
Equalising acoustical response
NEXO loudspeakers are acoustically designed for maximum efficiency over their operating bandwidth.
The NX242 provides the correction required to obtain a flat system response. Active rather than passive
attenuation allows the lowering of amplifier voltages for a given output SPL and therefore increases the
maximum SPL achievable with the same amplifier. Active equalisation can also extend a NEXO
loudspeaker’s frequency response, especially at low frequencies where acoustical performance is
limited by cabinet size.
While many DSP processors can provide this type of EQ, none can include the extensive measurement
facilities and listening tests employed by NEXO R&D when adjusting NX242 setups for a particular
loudspeaker.
Crossover section
Crossover between different bands is tuned for every set-up of every cabinet. The crossover is
designed to ensure the best phase alignment possible throughout the crossover overlap region.
Each crossover is “made to measure” in order that each transducer can fit with its neighbour by
achieving a perfect phase alignment. Unconventional filters are used, ranging from 6dB/octave to near
infinite slopes depending of the type of crossover wanted. Time alignment is also performed in an
unconventional way, by using the crossover filter group delays in combination with allpass and/or
frequency dependent delays.
NEXO NX242-ES4 DIGITAL CONTROLLER FOR GEO S12 Page 77/112
3
R+L
2
L
1
R
Voice Coil Temp.
ChassisTemp
Command
PHYSIO 1
Command
PEAK SIMULATION
PATCH
Disp.
Command
Voice Coil Temp.
ChassisTemp.
LF TEMPERATURE
0
INPUT VU-METER
0
A/D EQ
A/D
DACMUTEEQ
EQ
SHELVING
SHELVING
A/D EQ
Command
HF TEMPERATURE
VCA
FALLBACK
AMP VOLTAGE
Signal
AMP POWER
AMP GAIN
Command
displacement
DISPLACEMENT 1
DELAY 1
ATT/REL.
5
SENSE 1
2
L
3
R+L
1
R
INPUT VU-METER
INPUT R
INPUT L
OUTPUT
CHANNEL 4
NX242 Digital TDcontroller Partial BLOCK DIAGRAM
Analogue path
Digital Audio
Digital servo & protections
HEADROOM
10.1.3 Protection
VCAs and VCEQs
Each channel has its own simulation and protection process.
Each audio channel contains a combination of controlled gain stages
(let's call them VCAs as in analogue circuitry). These VCAs are
embedded into complex composite signal chains that adapt change their
basic operation into frequency selective attenuation, similar to an analog
voltage controlled dynamic equaliser (VCEQ).
Each VCEQ and VCA is controlled via synthesis of several signals from
the various detection sections. That synthesis is in fact the envelope of
those signals, with an optimised release and attack time for each VCEQ
and VCA (depending on its frequency range and the cabinet selected).
Displacement Control
The Sense input signal is sent to a shaping filter producing a signal
whose instantaneous amplitude is proportional to the voice coil
excursion. This signal, after rectification, is compared to a preset
threshold matching the maximum usable value, as determined from
laboratory measurements. Any part of the signal exceeding the threshold
is sent to the VCEQ control buffer while the VCEQ acts as an
instantaneous (very short attack time) limiter to prevent displacement
from exceeding the maximum permissible value.
Temperature Control
Each sense signal is fed into a shaping filter (one per transducer), each
one producing a signal proportional to the instantaneous current flowing
into the voice coil of the transducer. After rectification, this signal is
integrated with attack and release time constants equivalent to the
thermal time constants of the voice coil and chassis, producing a voltage,
which is representative of the instantaneous temperature of the voice
coil.
When this voltage reaches the threshold value corresponding to the
driver’s maximum safe operating temperature, the VCA becomes active
to reduce the NX242’s output signal level until the effective temperature
falls below the maximum usable value.
In order to avoid detrimental effects induced by very long release time
constants produced by the temperature detection signal (system output
being reduced for an extended period, “pumping” effects, etc.), the
detection signal is modulated by another voltage integrated with faster
time constants that match the subjective perception of sound level. This
allows the controller to reduce the effective operating duration of the
temperature limiter and make it sound more natural, while the efficiency
of protection is fully preserved and protection thresholds are kept as high
as possible.
Physiologic Dynamic Control
The Physiologic Dynamic Control is intended to avoid unwanted effects
produced by long attack time constants. By anticipating the operation of
the temperature limiter, it prevents a high level audio signal appearing
suddenly, then being kept up for long enough to trigger the temperature
limiter. Without this, a rough and delayed gain variation would result that
would be quite noticeable and unnatural.
Page 78/112 NEXO NX242-ES4 DIGITAL CONTROLLER FOR GEO S12
The Physio control voltage acts independently on the VCA with its operation threshold slightly (3 dB)
above that of the temperature limiter and a low compression ratio; its optimised attack time constant
allows it to start operating without any subjectively unpleasant transient effects.
Peak Limiter
The peak limiter primary function is to avoid massive clipping of the amplifier, which can have some
very audible artefacts and in some cases may be damaging to the loudspeakers. Modulation of the
amplifier’s supply voltage rails can create very low frequencies or high-frequency, high level harmonics.
Since these occur after the NX242 in the signal path, they are not filtered by the TDcontroller circuitry.
The threshold of the peak limiter is set by the user to match the amplifier’s clipping point.
The second function of the peak limiter is to avoid huge amounts of power being sent to a driver. Each
driver is protected against overheating and overexcursion, but there could be other failure modes that
cannot be predicted by simulation (especially mechanical damage to the cone). Each driver is specified
for a certain power handling and a factory set peak limiter threshold is tuned to avoid any abuse.
10.2 Trouble shooting
The NX242 has been designed to be user-friendly. However with highly technical systems such as GEO
S12, incorrect adjustment of the NX242 can lower the quality & safety of your system. Listed below are
the most common errors encountered by NEXO Technical Support.
10.2.1 Operation of Multiple TDcontrollers output channels
Typically, GEO S12 systems require multiple NX242’s output channels per side. Eventually, two or
more NX242’s channels will operate within the same cluster. It is mandatory to verify the consistency of
the setups and adjustment between these channels to avoid the problems described below.
IMPORTANT
When using multiple NX242’s output channels in a single array, all parameters should be
consistent and set to proper values on each channel.
10.2.2 Amplifier Power (MENU 2.7)
If the amplifier power (MENU 2.7) is set to a value below the amplifer’s actual power, the peak limiter of
the NX242 will trigger continually, creating audible distortion. Please note that this peak limiter is not set
to act as a compressor on the signal. It is intended to minimize the clipping of the amplifier by operating
slightly after
the amplifier’s clipping point.
One way to properly adjust this parameter is to set amplifier power at maximum (5000W) and decrease
the value until the amplifier and TDcontroller clip at the same time.
10.2.3 Amplifier Gain (MENU 2.6)
It is very important to check the gain of each channel. These values should be set in agreement with
amplifier gain. The second line of the MENU2.6 displays the gain as seen by the NX242 to ease the
setting of this parameter.
10.2.4 Gains
If your amplifier gains are not the same on each channel, you will have to adjust the inter-channel gain
in order to compensate for this amplifier gain difference.
NEXO NX242-ES4 DIGITAL CONTROLLER FOR GEO S12 Page 79/112
10.2.5 Delays
Multiple NX242’s can be used on a single GEO S12 array. When changing the delay in one NX242
TDcontroller that is part of a multi-controller system, take great care to have exactly the same delay
setting in all NX242 TDcontrollers that receive the same input signal (i.e. all NX242’s that are fed from
the Left output of the mixing console should have the same delay settings). A Tangent Array is very
sensitive to delay differences between sections of the array in the same line. You could experience
coverage problems if all delays applied to a Tangent Array are not equal.
Please refer to the chapter in the NX242 User Manual on setting delay for proper time alignment
between GEO S12 and ALPHA S2 / CD18 / GEO SUB .
10.2.6 Reversed Cardioid Pattern
Polarity checks are often performed while the system is being set up. Keep in mind that cardioid
speakers may also require a coverage test. If you invert two outputs of the NX242, you could have the
main lobe inverted and firing to the rear. It may be quite hard to detect a reversed cardioid pattern when
it involves one section of a large array.
A good practice is to test the each cabinet in the array with the front speakers only. The system is then
omni-directional. Then turn on the back speaker: you should notice a massive reduction at the back,
and additional level at the front.
This test must be done in addition to the usual polarity test.
10.2.7 Using the wrong NX242 setups for a given cabinet
Each NX242 setup is tailored for a certain NEXO loudspeaker. Using the wrong setup will create safety
and quality problems. Always check that every cabinet in your system is being driven by the correct
NX242 setup.
10.2.8 Connections
To ensure correct electronic behaviour, and to guarantee specifications and EMC performance, a
NX242 must be properly wired. Always use balanced connectors with the shield connected to pin 1 on
both sides. For more wiring recommendations please refer to the application note in the NX242 manual
update.
Page 80/112 SYSTEM ALIGNMENT GUIDELINES
11 SYSTEM ALIGNMENT GUIDELINES
The NX242’s factory delay presets are optimised to provide the best possible crossover between the
GEO S12 and CD18 / S2 / GEO SUB systems. The reference point for this adjustment is the front of
each cabinet. (This means that the internal delays needed to achieve a correct time alignment are set
for cabinets standing next to each other with both fronts aligned). We recommend that the system is
adjusted so that arrivals from GEO S12 and CD18 / S2 / GEO SUB are coincident at a fairly distant
listening position.
11.1 GEO S12 Vertical Cluster design
Cluster design must be done with Geosoft2, which provides very intuitive and fast method to determine
all cluster geometry parameters in relation to venue where cluster is implemented.
IMPORTANT
Geosoft2 is a freeware downloadable on www.nexo-sa.com. Please check our website
periodically for upgrades.
Never install a GEO S12 cluster without checking its acoustical performances and
mechanical safety in Geosoft2 prior to installation.
Please contact your local distributor for assistance and/or training on Geosoft2
11.2 Stacked RS15 / CD18 / S2 / GEO SUB and Flown GEO S12
Recommended NX242 GEOS12 setup family: X-OVER
In the example below, r
1
being the distance from GEO S12 array to listener position, and r
2
being the
distance from GEO SUB to listener position, the distance difference is then r
1
r
2
(specified meters or
feet).
r
1
> r
2
, the delay should be set on the CD18 / S2 / GEO SUB NX242 TDcontroller channel.
r
1
< r
2
, the delay should be set on the GEO S12 NX242 TDcontroller channel
To convert the result in time delay (specified in seconds), apply:
t = (r
1
-r
2
)/C r
1
and r
2
in meters, C (sound speed) 343 m/S.
The delay parameter is set in MENU 1.2 (set the units to meters, feet or seconds according to your
preference). Delay will have to be adjusted according to the distance difference r
1
r
2
(see figure below).
r
1
r
2
SYSTEM ALIGNMENT GUIDELINES Page 81/112
11.3 Driving the GEO SUB’s from the AUX send
It is quite common to use the AUX send of a mixing desk to drive the Sub section of a PA system. This
gives the mixing engineer more flexibility to set the level of the subbass relative to the main PA, apply
special effects, or to use a different EQ on the Sub. However, it also raises some serious issues for the
performance & safety of the system (mostly time alignment).
At NEXO, great care is taken to design optimum phase alignment from one octave above to one octave
below the crossover frequency point. By doing so, drivers are working perfectly together and providing
the best efficiency possible. It is then up to the user to adjust the delay on the NX242 to match the
physical path difference of the different systems. It is thus possible to get a well adjusted system, even
without measuring instruments.
If CD18’s / GEO SUB’s / S2’s are driven form an AUX output, NX242 is fed with two signals coming
from different sources. If those two sources (MAIN output & AUX send) are not exactly in phase, delay
is introduced into the crossover between the GEO S12 array and the CD18’s / GEO SUB’s / S2’s. It is
then mandatory to use proper measurement tool to optimize phase response.
Why is it unlikely that AUX and MAIN outputs have the same phase?
Signal paths are likely to be different; any filter modifying the bandwidth and EQ of the
signal is also affecting the phase.
Example: a 24dB/oct high pass filter set at 15Hz is affecting amplitude of the signal by only
0.6dB at 30Hz, but the phase shift is 90°!! At 100Hz we can still measure 25° of phase shift.
Limiting bandwidth with a low pass filter can introduce a phase difference of up to 180°
(completely out of phase) at the cross over point.
If the signal is passing though any digital equipment, between 1.4ms and 2.2ms is being
added (around 70° phase shift at 100Hz) due solely to the converter delay! The additional
delay due to the processing itself (look ahead compressor, delay…) can be quite important
as well.
If both outputs are not measured in the actual configuration, it is very likely that phase alignment will not
be correct.
Consequences of badly aligned systems
Mis-aligned systems have lower efficiency: i. e. for the same SPL the system will have to be driven
harder, activating the displacement & temperature protection at lower output levels. Both sound quality
and reliability will decrease as the system is stressed.
Precautions & Checks
Before using the AUX of a mixing desk, ensure that MAIN and AUX outputs are in phase;
Always apply identical EQ or processing on both channels, so that the phase relationship will not be
altered;
Never add additional low pass filtering on the SUB or high pass filtering on the main system;
Inverting polarity on one channel should always result in a massive difference near the crossover point.
If that is not the case, the system is no longer aligned.
11.4 Recommended installation tools and equipment
Tape measure – should be 30m/100ft in length and be of durable fibre material. Have one per
array available to speed up the installation process.
Laser Inclinometer – For measuring vertical and horizontal angles in the venue. An ideal product
is the Calpac ‘Laser projecting a dot’ version which costs approximately 60 €.
Digital remote inclinometer – with a remote sensor in the bumper and a meter unit at ground level
to ensure precise installation of the cluster. NEXO GeoSight system predicts the stationary angle
Page 82/112 SYSTEM ALIGNMENT GUIDELINES
of the array, even while it is swinging, and has a green laser mounted coincident to and parallel
with the axis of the topmost cabinet.
Spirit level – used to ascertain the trueness of the surface from which the angle measurements
originate.
Rangefinder measuring device – either a Disto type laser measure or an optical laser rangefinder
can be used. Devices such as the Bushnell ‘Yardage Pro’ sports rangefinders provide sufficiently
accuracy and are easy to use. They have the additional advantage of working very well in bright
sunlight.
Electronic calculator with trigonometric functions to calculate the height from ground level to
points in the room. The formula to calculate height of a point from measured angle and distance
is:
Height of point = Sin(vertical angle in degrees) x distance to point
NB: Take care when using spreadsheets as they calculate using radians by default. To convert
degrees to radians use the formula:
Angle (in radians)=3.142 x Angle (in degrees)/180
Computer – Laptop or Desktop PC running Windows XP with the current version of NEXO
GeoSoft2 installed. It is not possible to configure a Geo tangent array properly without using
GeoSoft2. Note that, when GeoSoft2 designs are prepared prior to arrival at the venue, it is often
necessary to modify or update the design to accommodate special circumstances. A PC is
absolutely essential to make such changes.
Audio Analysis Software – recommended but not absolutely essential, programs such as Easera
Systune, Spectralab or Spectrafoo enable rapid and detailed analysis of the installation. Consider
taking a training course in using one of these tools if you are not already competent with them – it
will pay dividends in increased performance of the system.
GEO S12 RS15 / CD18/S2/GEOSUB SYSTEM CHECK LIST Page 83/112
12 GEO S12 RS15 / CD18/S2/GEOSUB SYSTEM CHECK LIST
It is essential to execute all these check steps prior to perform a sound check on the “front end” to the
system. Following this checklist step by step will prevent many troubles and will save time in the end.
12.1 Are the NX242 Digital TDcontrollers properly configured?
IMPORTANT
If you must change any of the parameters listed above, make sure that you use the same
values on all NX242’s.
12.1.1 NX242 settings
Output Assignment
NX Setup / NXChannel 1 2 3 4
GEOS12 Passive 4 Channels GEO S12 Ch1 GEO S12 Ch2 GEO S12 Ch3 GEO S12 Ch4
RS15 Omni Stereo - GEOS12 Passive Stereo RS15 Left RS15 Right GEO S12 Left Geo S12 Right
RS15 Cardio Mono - GEOS12 Passive Stereo RS15 Rear RS15 Front GEO S12 Left Geo S12 Right
S2 Stereo– GEOS12 Passive Stereo S2 Left S2 Right GEO S12 Left Geo S12 Right
CD18 Mono – GEOS12 Passive Stereo (1) CD18 Rear CD18 Front GEO S12 Left Geo S12 Right
GEO SUB Mono - GEOS12 Passive Stereo (1) GEO SUB Rear GEO SUB Front GEO S12 Left Geo S12 Right
GEOS12 Active 2 Channels GEO S12 LF Left GEOS12 HF Left GEO S12 LF Right GEO S12 HF Right
RS15 Cardio – GEOS12 Active Mono RS15 Rear RS15 Front GEO S12 LF GEOS12 HF
CD18 – GEOS12 Active Mono CD18 Rear CD18 Front GEO S12 LF GEOS12 HF
GEO SUB – GEOS12 Active Mono GEO SUB Rear GEO SUB Front GEO S12 LF GEOS12 HF
Output parameters
Output
Label
Amp
Gain (2)
Amp
Power (2)
Global
Gain
Global
Delay
Sense
Gain
Array EQ
(3)
Headrom
(4)
All channels 26 dB refer to amp 0 dB 0 ms 0 dB 0 5 bars
(1) Local gain and delay values are inter-locked channel 1&2
(2) values for recommended amplifier gain and power : should be set in agreement with selected
amplifiers specifications
(3) Should be in agreement with implemented cluster; acts on a shelving filter designed to compensate
for LF coupling.
(4) Disabled when using digital inputs.
12.2 Are the amplifiers properly configured?
Freq. Band Mode Gain Switch Limiter High Pass
All channels
Stereo 26 dB None None
12.3 Are the amps and the NX properly connected?
Check that the sense lines on the NX242’s are properly connected by applying a signal to the
corresponding output and verify that the correct Sense LED illuminates.
Page 84/112 GEO S12 RS15 / CD18/S2/GEOSUB SYSTEM CHECK LIST
12.4 Are the speakers properly connected and angled ?
Attach the first series of modules to the bumper.
Before flying, verify that all channels of all modules are functioning properly.
Make sure that each RS15 / CD18 / GEO SUB is producing the proper front/rear summation:
when listening from behind the array, switch the front drivers in and out. You should hear a
reduction in the LF range when the both front and rear drivers are on as compared to when the
rear drivers only are on. When listening from the front, you should hear a strong increase in the
LF range when connecting the rear drivers.
To check that all front elements have the proper amplitude and phase, you should listen to the
upper boxes at a close distance (<1 meter). You should be able to move from the top to the
bottom of the cluster without hearing any change in the tonal balance.
Verify that the angle settings are the same on both sides of each module.
Raise the bumper, attach the next series of modules and repeat the above checks.
Make sure that these series of modules sum properly with the modules above them.
When all the modules are flown, check that the aiming angles are the same left and right.
Make sure that multiple GEO S12 and RS15 / S2 / CD18 / GEO SUB are summing properly: 6
dB gain per doubling of quantity.
12.5 Final Pre-Sound Check Check
Play a CD track mono left, and then right: both sides must sound strictly identical. When listening in the
centre between Left and Right GEO S12’s, everything from LF to HF should be located to the “phantom
centre” position. If not, repeat the above check sequence to identify the source of the problem.
TECHNICAL SPECIFICATIONS Page 85/112
13 TECHNICAL SPECIFICATIONS
13.1 GEO S1230 Module
13.1.1 System specifications
PRODUCT FEATURES GEO S1230
Components HF: 1 x 3” voice coil, 1.4” throat 16 Ohms driver on a 5° hyperboloid reflective wavesource.
LF: 1 x 12” (30cm) high excursion neodymium 16 Ohm driver.
Height x Width x Depth 344 x 675 x 400 mm (13
1/2
” x 26
1/2
” x 15
1/2
”) excluding accessories
Rigging axis to axis height: 345mm (13
1/2
”)
Shape 30° Trapezoid.
Weight: net 26.8 kg (59.1 lbs) excluding accessories.
Connectors 2 x NL4MP SPEAKON 4 pole (In & Through)
Construction Baltic birch ply with structured black coating.
Front finish Molded Dark Grey Metal Grill.
Flying points Two plates connecting with external accessories.
Intercabinet angle adjustments = (16°) - 22.5° - 30°
SYSTEM SPECIFICATIONS GEO S1230 with NX242 TDcontroller & NX-tension Card
Frequency response [a] 53 Hz – 19 kHz ± 3 dB
Usable range @-6dB [a] 50 Hz – 20 kHz
Sensitivity 1W @ 1m [b] 103 dB SPL nominal
Peak SPL @ 1m [b] 131 to 133dB Peak (for 500 to 900 W RMS Amplifier)
Dispersion [c] Coupling Plane: 28.5°.
Non-Coupling Plane: Configurable 80° / 120°.
Crossover frequencies LF-HF: 1.1 kHz Passive or Active (internally configurable)
Nominal impedance HF: 16 Ohms; LF : 16 Ohms;
Recommended amplifiers
3 GEO S1230 in Parallel
HF: 875 to 1550 Watts into 4 Ohms
LF: 1750 to 3100 Watts into 4 Ohms
4 GEO S1230 in parallel
HF: 1000 to 1800 Watts into 4 Ohms
LF: 2000 to 3600 Watts into 4 Ohms
6 GEO S1230 in parallel
HF: 1650 to 3000 Watts into 2 Ohms
LF: 3300 to 6000 Watts into 2 Ohms
SYSTEM OPERATION
Electronic controller The NEXO TDcontrollers presets are precisely matched to the GEO S12 Series cabinets and include sophisticated
protection. Using GEO S12 Series cabinets without a properly connected NEXO TDcontrollers will result in poor sound
quality and can damage components.
Sub-bass CD18 / GEO SUB / S2 extend system low frequency response down to 32 Hz / 38 Hz / 32 Hz
Speaker cables Active:; 1
-
/1
+
:LF; 2
-
/2
+
: HF
Passive: 1
-
/1
+
: Not Connected; 2
-
/2
+
:LF + HF.
Accessories Please refer to the GEO S12 user manual before any operation.
As part of a policy of continual improvement, NEXO reserves the right to change specifications without notice.
[a] Response curves and data: anechoic far field above 200 Hz, half-space anechoic below 200 Hz.
[b] Sensitivity & peak SPL: will depend on spectral distribution. Measured with band limited pink noise.
Refers to the specified +/- 3 dB range. Data are for speaker + processor + recommended amplifier combinations.
[c] Directivity curves and data: 1/3 octave smoothed frequency response, normalized to on-axis response. Data obtained by computer processing of off-axis
response curves.
[d] Please refer to the GEO S12 user Manual.
Usable range data: frequency response capability with TD crossover slopes removed.
Page 86/112 TECHNICAL SPECIFICATIONS
13.1.2 Dimensions
30°
344 mm
13 1/2"
400 mm
15 1/2"
675 mm
26 1/2"
13.1.3 Diagrams
TECHNICAL SPECIFICATIONS Page 87/112
13.2 GEO S1210 Module
13.2.1 System specifications
PRODUCT FEATURES GEO S1210
Components HF: 1 x 3” voice coil, 1.4” throat 16 Ohms driver on a 5° hyperboloid reflective wavesource.
LF: 1 x 12” (30cm) high excursion neodymium 16 Ohm driver.
Height x Width x Depth 344 x 675 x 378 mm (13
1/2
” x 26
1/2
” x 14
7/8
”) excluding accessories
Rigging axis to axis height: 345mm (13
1/2
”)
Shape 10° Trapezoid.
Weight: net 28.05 kg (61.8 lbs) including array assembly system.
Connectors 2 x NL4MP SPEAKON 4 pole (In & Through)
Construction Baltic birch ply with structured black coating.
Front finish Molded Dark Grey Metal Grill.
Flying points Two plates connecting with external accessories.
Intercabinet angle adjustments = 0.2°, 0.315°, 0.5°, 0.8°; 1.25°, 2.0°, 3.15°, 5°, 6.3°, 8.0°, 10.0° (logarithmic steps)
SYSTEM SPECIFICATIONS GEO S1210 with NX242 TDcontroller & NX-tension Card
Frequency response [a] 53 Hz – 19 kHz ± 3 dB
Usable range @-6dB [a] 50 Hz – 20 kHz
Sensitivity 1W @ 1m [b] 103 dB SPL nominal
Peak SPL @ 1m [b] Configuration Dependent [d]
Dispersion [c] Coupling Plane: Configuration dependent [d]
Non-Coupling Plane: Configurable 80° / 120°.
Crossover frequencies LF-HF: 1.1 kHz Passive or Active (internally configurable)
Nominal impedance HF: 16 Ohms; LF : 16 Ohms;
Recommended amplifiers
3 GEO S1210 in Parallel
HF: 875 to 1550 Watts into 4 Ohms
LF: 1750 to 3100 Watts into 4 Ohms
4 GEO S1210 in parallel
HF: 1000 to 1800 Watts into 4 Ohms
LF: 2000 to 3600 Watts into 4 Ohms
6 GEO S1210 in parallel
HF: 1650 to 3000 Watts into 2 Ohms
LF: 3300 to 6000 Watts into 2 Ohms
SYSTEM OPERATION
Electronic controller The NEXO TDcontrollers presets are precisely matched to the GEO S12 Series cabinets and include sophisticated
protection. Using GEO S12 Series cabinets without a properly connected NEXO TDcontrollers will result in poor sound
quality and can damage components.
Array design Arrays of less than 4 x GEO S1210 will provide poor dispersion control and are neither recommended nor supported.
Sub-bass CD18 / GEO SUB / S2 extend system low frequency response down to 32 Hz / 38 Hz / 32 Hz
Speaker cables Active:; 1
-
/1
+
:LF; 2
-
/2
+
: HF
Passive: 1
-
/1
+
: Not Connected; 2
-
/2
+
:LF + HF.
Accessories Please refer to the GEO S12 user manual before any operation.
As part of a policy of continual improvement, NEXO reserves the right to change specifications without notice.
[a] Response curves and data: anechoic far field above 200 Hz, half-space anechoic below 200 Hz.
[b] Sensitivity & peak SPL: will depend on spectral distribution. Measured with band limited pink noise.
Refers to the specified +/- 3 dB range. Data are for speaker + processor + recommended amplifier combinations.
[c] Directivity curves and data: 1/3 octave smoothed frequency response, normalized to on-axis response. Data obtained by computer processing of off-axis
response curves.
[d] Please refer to the GEO S12 user Manual.
Usable range data: frequency response capability with TD crossover slopes removed.
Page 88/112 TECHNICAL SPECIFICATIONS
13.2.2 Dimensions
344 mm
13 1/2"
378 mm
15"
675 mm
26 1/2"
10°
13.2.3 Diagrams
TECHNICAL SPECIFICATIONS Page 89/112
731 mm
656 mm
294 mm
13.3 GEO S12 Touring Applications Accessories
13.3.1 GEO S12 Bumper
Parts
Dimensions
Weight
20 kg / 44.1 Lbs
Page 90/112 TECHNICAL SPECIFICATIONS
#GEOS12-XBOW-V2
13.3.2 GEO S12 Rigging Plates
Parts
Dimensions
376,50
53
352,3
Weight (pair)
10.7 kg / 23.6 Lbs
TECHNICAL SPECIFICATIONS Page 91/112
#GEOS12-TLB
13.3.3 Tension Mode Link Bars for GEOS12-XBOW-V2
Parts
Dimensions
46.1
225.3
Weight (pair)
0.6 kg / 1.3 Lbs
Page 92/112 TECHNICAL SPECIFICATIONS
13.3.4 Lifting Ring
Parts
Dimensions
132
36
58
Weight (kit)
0.3 kg / 0.661 Lbs
TECHNICAL SPECIFICATIONS Page 93/112
#GEOS12-TCBRK-V2
13.3.5 Truss hook for GEOS12-SSBRK or GEOS12-PSBRK
Parts
Dimensions
198
135
4
7
Weight (kit)
0.620 kg / 1.37 Lbs
Page 94/112 TECHNICAL SPECIFICATIONS
#GEOS12-TTC-V2
13.3.6 Truss hook for single vertical GEO S12
Parts
Dimensions
47.5
41
264
Weight (kit)
0.7 kg / 1.54 Lbs
TECHNICAL SPECIFICATIONS Page 95/112
#GEOS12-SSBRK-V2
13.3.7 “U” Bracket for single vertical GEO S12
Parts
Dimensions
899
575
212
Weight (kit)
7 kg / 15.4 Lbs
Page 96/112 TECHNICAL SPECIFICATIONS
#GEOS12-PSBRK-V2
13.3.8 U” Bracket for two vertical GEO S12
Parts
Dimensions
899
737
284
Weight (kit)
10.4 kg / 22.9 Lbs
TECHNICAL SPECIFICATIONS Page 97/112
#GEOS12-GSTK
x 4
x 2
x 8
In Service Equipment Storage Pattern
13.3.9 Ground Stacking Device for up to 6 GEO S1210
Parts
Dimensions
307
1035
1030
860
Weight (kit)
26.5 kg / 58.4 Lbs
Page 98/112 TECHNICAL SPECIFICATIONS
13.4 GEO S12 Fixed Installations Accessories
13.4.1 GEO S12 Bumper
Parts
Dimensions
691
251
215
Weight (kit)
14.5 kg / 32 Lbs
TECHNICAL SPECIFICATIONS Page 99/112
13.4.2 GEO S12 Connecting Plate 1
Parts
Dimensions
313
6
216
Weight (kit)
7.5 kg / 16.5 Lbs
Page 100/112 TECHNICAL SPECIFICATIONS
13.4.3 GEO S12 Connecting Plate 2
Parts
Dimensions
310
6
173
Weight (kit)
6.2 kg / 13.7 Lbs
TECHNICAL SPECIFICATIONS Page 101/112
13.4.4 GEO S12 Connecting Plate 3
Parts
Dimensions
293
6
169
Weight (kit)
5.5 kg / 12.1 Lbs
Page 102/112 TECHNICAL SPECIFICATIONS
13.4.5 Single GEO S12 “U” Bracket
Parts
Dimensions
Weight
2.9 kg / 6.4 Lbs
172
712
400
TECHNICAL SPECIFICATIONS Page 103/112
13.4.6 “L” Bracket for cable suspension
Parts
Dimensions
51
44
301
Weight (kit)
1.75 kg / 3.86 Lbs
#GEOS12-LBRK
WARNING : Screws must be secured using Loctite 243
TM
Page 104/112 TECHNICAL SPECIFICATIONS
13.4.7 “U” Bracket for rigid suspension
Parts
Dimensions
51
112
199
Weight (kit)
1.75 kg / 3.86 Lbs
#GEOS12-ABRK
WARNING : Screws must be secured using Loctite 243
TM
TECHNICAL SPECIFICATIONS Page 105/112
8 mm
20 mm
13.4.8 GEO S12 Push-Pins (BLGEOS)
WEIGHT: 0.032 KG / 0.07 LBS
Page 106/112 TECHNICAL SPECIFICATIONS
13.5 GEO S12 Analogue TDcontrollers
13.5.1 Specifications
SPECIFICATIONS
Output Section +22 /+16/+10 dBm typ. into 600 Ohm load. Back Panel switch on +6/0/-6dB respectively.
Input Section Maximum input Level : 22dBu. CMRR 80dB @ 1kHz typ.
THD+N 0.1% @ 1kHz Typ. for +10dBm Output
Noisefloor S12TD -100 dBV for 0dB switch position (22 Hz - 22 kHz, UnWeighted)
Dynamic Range 111 dB UnWeighted (THD+N at-60dBr sine wave @1kHz rel.max. output)
Crosstalk 104dB
Filtering & EQ. L&R: 12dB/oct Low Pass, 12dB/oct High pass (crossover or overlap), 4 Parameter EQs.
All factory tuned
Protections VCA temp. (SUB,LF & LF), VCEQ disp. (SUB & LF), Peak Limiter (all chanels), Power
compression regulation
Power Supply 100-250 Volts (continuous operation), 50/60Hz. Power 9W. Peak Inrush current 0.5A.
Earth-Lift.
Conformity Comply with safety objective of 73/23/EEC & 89/336/EEC directives. (EN60065-12/2001,
EN55103-1996).
CB scheme DK-8371, cULus 60065 AZSQ E241312, FCC part15 class B
PRODUCT FEATURES
Audio Inputs Two differential non floating L&R Audio inputs, 50 kOhm. Two XLR-3F connectors.
Sense Inputs Three Amplifier Sense Inputs (S12 L&R, LS). 400 kOhm. 6 Pole Removable Strip
Terminal
Audio Outputs Two L&R S12 Audio outputs. Balanced, non floating, 51 Ohm. Two XLR-3M.
One Mono (L+R) LS400 Audio output. Balanced, non floating, 51 Ohm. One XLR-3M.
Controls Gain switch (back panel), 3 positions : -6 / 0 /+6dB.
Peak Limiter trimmer (1200W-600W/8 Ohms) for S12 & Subbass
Sub Overlap / Crossover switch & Sub Gain Control (-/+ 6dB).
Indicators LF speakers Protect Yellow LED's (Temp. & Disp), Power ON (green), Amp Sense &
Peak LED's (green/Red)
Dimensions 1U 19" Rack. 165mm (6.5") Depth
Weight : 2.9 kg (6.6 lbs) net
SYSTEM OPERATION
Applicable Products The S12 TDcontroller is precisely matched to the S12 & associated Subbass and includes
sophisticated protection systems. Use of either product without a properly connected
Controller will result in poor sound quality and may damage the components.
SubBass Active two-way operation of the S12 Loudspeaker with the associated Subwoofer is
included in the Analogue S12 TDcontroller .
13.5.2 Front and Rear Panel view
BALANCED INPUTS
RIGHT LEFTRIGHT LEFTSUB L+R
OUPUT
LEVEL
+6dB
0dB
-6dB
BALANCED OUTPUTS
EARTH
LIFT
115-230V 50-60Hz 10W
CAUTION !
To reduce the risk of electric schock
grounding of the center pin
of this plug must be maintained.
MADE IN FRANCE
+ RIGHT - + LEFT -+ SUB -
SENSE INPUT
(from amp terminals)
CAUTION !
Sense line must be connected
for speaker protection.
10CE
PS8 TDcontroller
s.n:
03105
4004
TECHNICAL SPECIFICATIONS Page 107/112
13.6 NX242 TDcontroller with NX-Tension Card
13.6.1 Specifications
SPECIFICATIONS
Output Level +28 dBu Max. into 600 Ohm load
Dynamic Range 110 dBu
THD + Noise < 0.002% flat setup (for output at 27.5dBu)
Latency time 1.7ms on a flat setup
Power Supply 90V-260V
PRODUCT FEATURES
Audio Inputs 2 Audio Inputs 24 bit converters
Electronically Balanced, 50k Ohm.
2 XLR-3F Connectors.
4 Digital Ethersound Inputs with NXTension ES4 Card
Sense Inputs 4 Amplifier Sense Inputs
Floating 150 k. 18 bit converters
8 Pole Removable Strip Terminal.
Audio Outputs 4 Audio Outputs. 24 bit converters
Electronically balanced, 50 Ohm
4 XLR-3M connectors
4 Digital Ethersound Outputs with NXTension ES4 Card (enabled for
compatible amplifiers only)
Processing 24 bit data with 48-bit accumulator. 200 MIPS
Front Panel
Menu A and Menu B buttons
16 characters by 2 lines display
Select Wheel & Enter button ()
IN Clip – DSP Clip red LED’s
Speaker Protection yellow LED for each channel
Individual Mute/Solo buttons and red LED for each channel
Amp. Sense & Peak (green & red) LED’s for each channel
FLASH EPROM Software updates/upgrades, new system setups, available on www.nexo-
sa.com
Rear Panel RS232 connector for serial com
2 x RJ45 connectors with NXTension ES4 Card
1 RJ45 + 2 RJ11 with NXTension CAI Card
Dimensions & Weight 1U 19" Rack - 230 mm (9") Depth.
4 kg
13.6.2 Front and Rear Panel view
GeoD Passive mode
Crossover 80Hz
SENSE INPUT
(from amp terminals)
BALANCED OUTPUTS
+ 4
-
+ 3
-
+ 2
-
+ 1
-
RS232
FLOATING BALANCED INPUTS
Channel 4 Channel 3 Channel 2 Channel1 B (RIGHT) A (LEFT)
MADE IN FRANCE
115-230V 50 - 60Hz 45W
CAUTION !
To reduce the risk of electric schock, grounding
of the center pin of this plug must be maintained.
NX242
NX242 TDcontro
03105
sept.04
NXtension-ES
In Rx
In Tx
Out Rx
Out Tx
Out In
Page 108/112 TECHNICAL SPECIFICATIONS
13.6.3 Block Diagram
3
R+L
2
L
1
R
Voice Coil Temp.
ChassisTemp
Command
PHYSIO 4
Voice Coil Temp.
ChassisTemp
Command
PHYSIO 3
Voice Coil Temp.
ChassisTemp
Command
PHYSIO 2
Voice Coil Temp.
ChassisTemp
Command
PHYSIO 1
Command
PEAK SIMULATION 4
Command
PEAK SIMULATION 3
Command
PEAK SIMULATION 2
Command
PEAK SIMULATION
PATCH 4
PATCH 3
PATCH 2
PATCH
Disp.
Command
Voice Coil Temp.
ChassisTemp.
LF TEMPERATURE 4
Disp.
Command
Voice Coil Temp.
ChassisTemp.
LF TEMPERATURE 3
Disp.
Command
Voice Coil Temp.
ChassisTemp.
LF TEMPERATURE 2
Disp.
Command
Voice Coil Temp.
ChassisTemp.
LF TEMPERATURE
0
INPUT VU-METER
0
A/D EQ
A/D
DACMUTEEQ
EQ
A/D DACMUTEEQ
EQ
A/D
SHELVING
DACMUTEEQ
EQ
A/D DACMUTEEQ
EQ
SHELVING
A/D EQ
Command
HF TEMPERATURE 4
Command
HF TEMPERATURE 3
Command
HF TEMPERATURE 2
Command
HF TEMPERATURE
VCA
VCA
VCA
VCA
FALLBACK
AMP VOLTAGE
Signal
AMP POWER
AMP GAIN
FALLBACK
AMP VOLTAGE
Signal
AMP POWER
AMP GAIN
FALLBACK
AMP VOLTAGE
Signal
AMP POWER
AMP GAIN
FALLBACK
AMP VOLTAGE
Signal
AMP POWER
AMP GAIN
Command
displacement
DISPLACEMENT 4
Command
displacement
DISPLACEMENT 3
Command
displacement
DISPLACEMENT 2
Command
displacement
DISPLACEMENT 1
DELAY 4
DELAY 3
DELAY 2
DELAY 1
ATT/REL.3
ATT/REL.2
ATT/REL.1
ATT/REL.
2
L
3
R+L
1
R
2
L
3
R+L
1
R
2
L 1
3
R+L 1
8
SENSE 4
7
SENSE 3
6
SENSE 2
5
SENSE 1
1
R 1
2
L
3
R+L
1
R
INPUT VU-METER
INPUT R
INPUT L
OUTPUT
CHANNEL 4
OUTPUT
CHANNEL 3
OUTPUT
CHANNEL 2
OUTPUT CHANNEL 1
NX242 Digital TDcontroller BLOCK DIAGRAM
Analogue path
Digital Audio
Digital servo & protections
HEADROOM
HEADROOM
1
2
3 3
4
4
5
6
7 7
8
9
9
10
11
12
13
GEO S12 SERIES PARTS & ACCESSORIES LIST Page 109/112
14 GEO S12 SERIES PARTS & ACCESSORIES LIST
14.1 Modules & Control Electronics List
MODEL DRAWING DESCRIPTION
GEO S1230
GEO S1230 Module
GEO S1210
GEO S1210 Module
NX 242–ES4 Digital TDcontroller
NXAMP4x1 Digital Powered Controller 4x1300W
NXAMP4x4 Digital Powered Controller 4x4000W
14.2 Accessories List
MODEL DRAWING DESCRIPTION
GEOS12-BUMPER
Main GEOS12 Bumper for touring application.
GEOS12-XBOW-V2
Rigging plates for touring applications (pair).
GEOS12-TLB
Link Legs for GEOS12-XBOW-V2 with Oblong Holes
(pair, includes 2 8x20 Quick Release Pins)
BLGEOS
8x20 Quick Release Pin for Geo S8 / GeoS12 / RS15
GEOS12-XHBRK
Lifting Ring for GEOS12-SSBRK or GEOS12-PSBRK
or GEOS12-XBOW (includes 8x45 Quick Release
Pin).
GEOS12-TCBRK-V2
Truss hook for GEOS12-SSBRK or GEOS12-PSBRK
or GEOS12-XBOW (includes 8x45 Quick Release Pin)
Page 110/112 GEO S12 SERIES PARTS & ACCESSORIES LIST
MODEL DRAWING DESCRIPTION
GEOS12-TTC-V2
Truss hook for single vertical GEO S12
GEOS12-SSBRK-V2
“U” Bracket for single horizontal GEO S12 on tripod or
on truss hook or lifting ring
GEOS12-PSBRK-V2
U” Bracket for two GEO S12 on subwoofer pole stand
or on truss hook or on lifting ring
GEOS12-GSTK
Ground Stack Device for up to 6 Geo S1210
GEOS12-FBUMPER
Main GEOS12 Bumper for fixed installation.
GEOS12-ANPL1
Connecting Plates / range: 0.20° - 3.15° for fixed
installation.
GEOS12- ANPL2
Connecting Plates / range: 5.00° - 10.00° for fixed
installation.
GEOS12- ANPL3
Connecting Plates / range: 16.00° - 30.00° for fixed
installation.
GEOS12-UBRK
“U” Bracket for fixed installation.
GEOS12- LBRK
“L” Bracket for cable suspension (for fixed installation).
GEOS12- ABRK
“U” Bracket for rigid suspension (for fixed installation).
GEOS12-2CASE Flight Case for 2 GEO S12 with accessory tray
GEOS12-3CASE Flight Case for 3 GEOS12 equipped with XBOWS
GEOS12-BCASE Flight Case for 2 GEO S12 bumpers and accessories
USER NOTES Page 111/112
15 USER NOTES
Page 112/112 USER NOTES
France
Nexo S.A.
Parc d’activité de la dame jeanne
F-60128 PLAILLY
Tel: +33 3 44 99 00 70
Fax: +33 3 44 99 00 30
www.nexo-sa.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112

Yamaha S12 El manual del propietario

Categoría
Equipo de música suplementario
Tipo
El manual del propietario