Maytag MFF2558DEH00 User Instructions

Marca: Maytag

Modelo: MFF2558DEH00

Categoría: Neveras

Tipo: User Instructions

Este manual también es adecuado para

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.maytag.com. In Canada, register your

refrigerator at www.maytag.ca.

For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall of the

refrigerator compartment.

Model Number Serial Number

TableofContents/ Indice/ Tabledesmati res

REFRIGERATOR SAFETY ................................ 2

Proper Disposal of Your Old Refrigerator ......3

INSTALLATION INSTRUCTIONS ..................... 3

Unpack the Refrigerator ................................. 3

Location Requirements .................................. 4

Electrical Requirements .................................. 4

Water Supply Requirements .......................... 4

Connect the Water Supply ............................. 5

Refrigerator Door(s) and Drawer .................... 6

Door Closing and Door Alignment ............... 12

REFRIGERATOR USE ..................................... 12

Opening and Closing Doors ......................... 12

Using the Controls ........................................ 13

Electronic Controls ....................................... 13

Digital Controls ............................................. 13

Crisper Humidity Control .............................. 15

Ice Maker ...................................................... 15

Water Dispenser ........................................... 15

Water Filtration System ................................ 16

REFRIGERATOR CARE .................................. 16

Cleaning ........................................................ 16

Changing the Light Bulb ............................... 17

Vacation and Moving Care ........................... 17

TROU BLESI-IOOTI NG ..................................... 18

Refrigerator Operation .................................. 18

Temperature and Moisture ........................... 19

Ice and Water ............................................... 19

Accessories .................................................. 20

WATER FILTER CERTIFICATIONS ................ 20

PERFORMANCE DATA SHEETS ................... 21

WARRANTY .................................................... 23

SEGURIDAD DEL REFRIGERADOR .............. 24

C6mo deshacerse adecuadamente

de su refrigerador viejo ................................. 25

INSTRUCCIONES DE INSTALACION ............ 25

Desempaque el refrigerador ......................... 25

Requisitos de ubicaci6n ............................... 26

Requisitos electricos .................................... 26

Requisitos del suministro de agua ............... 27

Conexi6n del suministro de agua ................. 27

Puerta(s) y caj6n del refrigerador ................. 29

Cierre y alineamiento de la puerta ............... 35

USO DE SU REFRIGERAI)OR ........................ 35

C6mo abrir y cerrar las puertas .................... 35

Uso de los controles ..................................... 36

Controles electr6nicos .................................. 36

Controles digitales ........................................ 36

Control de humedad del

caj6n para verduras ...................................... 38

F_brica de hielo ............................................ 38

Despachador de agua .................................. 38

Sistema de filtraci6n de agua ....................... 39

CUII)AI)O DE SU REFRIGERAI)OR .............. 39

Limpieza ........................................................ 39

C6mo cambiar el foco .................................. 40

Cuidado durante las

vacaciones y mudanzas ............................... 40

SOLUCION DE PROBLEMAS ........................ 41

Funcionamiento del refrigerador .................. 41

Temperatura y humedad .............................. 42

Hielo y agua .................................................. 42

Accesorios .................................................... 43

I-IOJA DE I)ATOS l)EL RENI)IMIENTO .........44

GARANTJA ....................................................... 46

SECURITE DU REFRIGERATEUR ................. 48

Mise au rebut adequate de

votre vieux refrigerateur ................................ 49

INSTRUCTIONS I)'INSTALLATION ............... 49

Deballage du refrigerateur ............................ 49

Exigences d'emplacement ........................... 50

Specifications electriques ............................ 50

Specifications de I'alimentation en eau .......51

Raccordement de la canalisation d'eau .......51

Porte(s) et tiroir du refrig6rateur ................... 53

Fermeture et alignement de laporte ............ 59

UTILISATION l)U RI_FRIGI_RATEUR ............. 59

Ouverture et fermeture des portes ............... 59

Utilisation des commandes .......................... 60

Commandes electroniques .......................... 60

Commandes numeriques ............................. 60

Reglage de I'humidite

dans le bac & legumes .................................. 62

Machine &glagons ....................................... 62

Distributeur d'eau ......................................... 62

Systeme de filtration de I'eau ....................... 63

ENTRETIEN l)U RI_FRIGI_RATEUR ............... 63

Nettoyage ..................................................... 63

Remplacement de I'ampoule d'eclairage ....64

Entretien avant les vacances

ou Iors d'un demenagement ........................ 64

I)I_PANNAGE ................................................... 65

Fonctionnement du refrigerateur .................. 65

Temperature et humidite .............................. 66

Glagons et eau.............................................. 66

Accessoires .................................................. 67

FEUlLLES DE I)ONNI£'ES

SUR LA PERFORMANCE ............................... 68

GARANTI E ....................................................... 70

W10621530A

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

[] Plug into a grounded 3 prong outlet.

[] Do not remove ground prong.

[] Do not use an adapter.

[] Do not use an extension cord.

[] Disconnect power before servicing.

[] Replace all parts and panels before operating.

[] Remove doors from your old refrigerator.

[] Use nonflammable cleaner.

[] Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

[] Use two or more people to move and install refrigerator.

[] Disconnect power before installing ice maker (on ice maker

kit ready models only).

[] Use a sturdy glass when dispensing ice (on some models).

[] Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

ProperDisposalofYourOldRefrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoffthe doors.

• Leave the shelves in place so that children may not easily

climb inside.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

Clean Before Using

After you remove all of the packaging materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

• Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator isheavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

_ ,.s__S@_i _'_'_'_'4_

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household

use only.

To ensure proper ventilation for your refrigerator, allow for _/2"

(1.25 cm) of space on each side and at the top. Allow for 1"

(2.54 cm) of space behind the refrigerator. If your refrigerator has

an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave 2W' (6.3 cm) minimum on the hinge side (some models

require more) to allow for the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a maximum

of 110°F (43°C). The preferred room temperature range for

optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

21/2" (6.3 crn) --

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an extension

cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the refrigerator to OFE Depending on

your model, turn the freezer control to the word OFF, or press the

Freezer down arrow or minus sign touch pad until a dash (-)

appears in both the Freezer and Refrigerator displays as shown.

Disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source and

reset the temperature controls to the desired setting. See "Using

the Controls."

...............I ]

, ..... @/_, !/_,, .......

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • V4"Nut driver

• 7/le"and W' Open-end or two • V4"Drill bit

adjustable wrenches • Cordless drill

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 34e"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

• For models with water filters, the disposable water filter

should be replaced at least every 6 months.

Water Pressure Connect to Water Line

A cold water supply with water pressure of between 35 and

120 psi (241 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration

System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IM PORTANT:

• Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX

(cross-linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator

are acceptable, and will help avoid off-taste or odor in your ice

or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the

following Whirlpool Part Numbers:

W10505928RP (7 ff [2.14 m] jacketed PEX),

8212547RP (5 ft [1.52 m] PEX), or

W10267701RP (25 ft [7.62 m] PEX).

Install tubing only in areas where temperatures will remain

above freezing.

If you turn on the refrigerator before the water line is

connected, turn off the ice maker to avoid excessive noise or

damage to the water valve.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Find a V2"to 1V4" (12.7 mm to 31.8 mm) vertical cold water

pipe near the refrigerator.

IMPO RTANT:

• Make sure it is a cold water pipe.

Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower right rear of the refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use

V4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

5. Using a cordless drill, drill a V4"hole inthe cold water pipe you

have selected.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the V4"drilled hole in

the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws slowly

and evenly so the washer makes a watertight seal. Do not

overtighten.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten or

you may crush the copper tubing.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from

the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a "P" clamp.

A _"

A. Copper tubing

B. "P" clamp

C. Compression nut

D. Compression sleeve

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with

the copper tubing. Avoid kinks when coiling the copper

tubing.

2. Remove the plastic cap from water valve inlet port. Place a

compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet

port. Shape tubing slightly so that the tubing feeds straight

into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the

water valve inlet port.

........ O

A. Plastic water tubing C. Compression nut

B. Sleeve D. Copper tubing

Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise

to completely tighten. Do not overtighten.

..........C

..........D

A. "P" clamp

B. Plastic water fine

C. Compression nut

D. Copper tubing

6. Check connection by pulling on copper tubing. Attach the

plastic water line to the refrigerator cabinet with a "P" clamp.

7. Turn on water supply to the refrigerator and check for leaks.

Correct any leaks.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill the ice storage bin.

TOOLS NEEDED: %e", 3/8",¼" hex head socket wrenches, a #2

Phillips screwdriver, and a flat-blade screwdriver.

IMPORTANT:

• Your refrigerator has a standard reversible refrigerator door

with either a freezer door or freezer drawer, or French doors.

Follow the instructions specific to the door style of your

model.

All graphics referenced in the following instructions are

included later in this section after "Final Steps." The graphics

shown for the standard door are for a right-hand swing

refrigerator (hinges factory installed on the right).

If you only want to remove and replace the doors see

"Remove Doors and Hinges" and "Replace Doors and

Hinges."

Before you begin, turn the refrigerator control OFF, and

remove food and adjustable door or utility bins from the doors.

Remove and Replace Handles

Refrigerator Door(s)

• To remove handles, use a3_32"hex key to loosen the two

setscrews located on the side of each handle. Pull the handle

straight out from the door or drawer. Make sure you keep the

screws for reattaching the handles. See Handle graphics 1

or 2.

• To replace handles, reverse the directions.

Freezer Drawer

• To remove handles, use a3_32"hex key to loosen the two

setscrews located under each handle. Pull the handle straight

out from the door or drawer. Make sure you keep the screws

for reattaching the handles. See Graphic 4.

• To replace handles, reverse the directions.

Freezer Door

• To remove handle, use a flat-blade screwdriver to remove the

two screws fastening the handle to the freezer door. See

Graphic 4.

• To replace handle, reverse the directions.

RemoveDoorsand Hinges

Standard Door

Hex Head Top Hinge Screw

Freezer drawer models

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator door closed until you are ready to lift it

free from the cabinet.

NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket

magnets to hold the door in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the refrigerator door free from the cabinet.

4. Remove the parts for the bottom hinge as shown in Bottom

Hinge graphic.

Freezer door models

1. Unplug refrigerator or disconnect power.

2. Keep the freezer door closed until you are ready to lift it free

from the cabinet.

NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket

magnets to hold the door in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the refrigerator door free from the cabinet.

4. Remove the center hinge pin and remove the hinge screws as

shown in the Center Hinge graphic. Lift the freezer door free

from the cabinet.

5. Remove the base grille by grasping the grille firmly with both

hands and pulling it toward you.

6. Remove the parts for the bottom hinge as shown in Bottom

Hinge graphic.

French Doors

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

3. Starting with the right-hand side door, remove the parts for the

top hinge as shown in Top Hinge graphic. Lift the refrigerator

door from the bottom hinge pin.

4. Remove the hinge pin cover from the bottom hinge pin and

keep it for later use. See Bottom Hinge graphic.

5. Before removing the left-hand side door, disconnect the wiring

plug located on top of the top hinge by wedging a flat-blade

screwdriver or your fingernail between the two sections. See

Wiring Plug graphic.

NOTE: The green, ground wire remains attached to the hinge.

Remove the parts for the left-hand side door top hinge as

shown in the Top Hinge graphic. Lift the door from the bottom

hinge pin.

NOTE: Remove the hinge pin cover from the bottom hinge pin

and keep it for later use. See Bottom Hinge graphic.

Reverse Door - Standard Door (optional)

IMPORTANT: If you want to reverse your door so it opens from

the opposite side, follow these steps. If you are not reversing the

door, see "Replace Door(s) and Hinges."

Door StopScrew DoorHandle Seal Screw Front

Flat-Head Handle Screw Cabinet Hinge Hole Plug

Cabinet

1. Remove hinge screws from handle side and move them to

opposite side. See Graphic 1.

Refrigerator door

1. Remove the refrigerator handle assembly as shown in

Graphic 2. Keep all parts together.

2. Remove door handle seal screw front. Move to opposite side

of refrigerator door as shown in Graphic 5.

3. Remove the door stop. Move it to the opposite side of the

refrigerator door as shown in Graphic 3.

4. Attach refrigerator handle on opposite side of the refrigerator

door with the two screws as shown in Graphic 2. Replace

handle trim as shown.

Tighten all screws. Set aside the door until hinges and freezer

compartment drawer are in place.

Freezer door

1. Remove the freezer handle assembly as shown in Graphic 4.

Keep all parts together.

2. Remove door stop. Move to opposite side of freezer door as

shown in Graphic 3.

3. Attach handle to opposite side of freezer door.

4. Tighten all screws. Set the door aside.

5. Remove the base grille by grasping the grille firmly with both

hands and pulling it toward you.

NOTE: Place a shim under the bottom front edge of the

refrigerator cabinet to take the weight off the roller brackets.

Remove the screws from both roller brackets. See Graphic 6.

Remove the hinge plate located behind the roller bracket and

move it to the opposite side of the refrigerator. Move the hinge

pin and shim to the outside hole on the hinge plate. See

Graphic 6.

Replace Doors and Hinges

Standard Door

NOTE: Graphics may be reversed if door swing is reversed.

Freezer drawer models

1. Replace the parts for the bottom hinge as shown. Tighten

screws.

NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket

magnets to hold the door in place while you are working.

2. Assemble the parts for the top hinge as shown in Top Hinge

graphic. Do not tighten screws completely.

3. Adjust the door so that the bottom of the refrigerator door is

aligned with the top of the freezer drawer. Tighten all screws.

Freezer door models

Make sure the hinge plate is securely fastened behind the

roller bracket and that the hinge pin is inserted into the outside

hole. Fully tighten all roller bracket screws. See Graphic 6.

Remove the shim that you placed under the front edge of the

refrigerator cabinet. Replace the freezer door.

NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket

magnets to hold the door in place while you are working.

3. Assemble the parts for the center hinge as shown in the

Center Hinge graphic, and tighten all the screws. Replace the

refrigerator door.

4. Assemble the parts for the top hinge as shown in the Top

Hinge graphic. Do not tighten the screws completely.

5. Adjust the doors so that the bottom of the refrigerator door is

aligned with the top of the freezer door. Tighten all screws.

French Doors

1. Assemble the parts for the top hinges as shown in Top Hinge

graphic. Do not tighten the screws completely.

2. Replace the parts for the bottom hinges as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator doors.

NOTE: Provide additional support for the refrigerator doors

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the doors in place while you are

working.

Align each door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

4. Reconnect the wiring plug on top of the left-hand side

refrigerator door.

5. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT:

• Two people may be required to remove and replace the freezer

drawer.

• All graphics are included later in this section after "Final

Steps."

Remove Drawer Front

Open the freezer drawer to full extension.

Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to insert the two screws

in the bottom of the drawer front into the brackets. See

Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are in

place. Reinstall top hinge cover as shown in Top Hinge

graphic.

2. Replace the base grille.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

3. Plug into a grounded 3 prong outlet.

4. Return all removable door parts to door and food to

refrigerator.

Standard Door - Freezer Door

A Flat-Head Haedle Screws

B. Refege_ator Door Handte

Front V_ew

A B

A, Door Stop Screws

B, Door Stop

A Flat-Head Handle

Screws

Door Handle

Seat Screw

Fro_t

@ ................A

A. Hiage Pm Shim

D Bottom Hinge

C. Hinge Plate

D. Rotter Br_ket

E, _f Hex-Head Hinge Screws

Standard Door - Freezer Drawer

A. Flat-Head Handle Screws

B. Refrigerator Door Handle

Front View Side View _._

I E

A B

A. Door Stop Screws

B. Door Stop

B. Freezer Drawer Handle

_'1_ ======_ o o

1"_'; A

A. Hinge Screws

Door Handle

Seal Screw

Front

I!I---

A. Loosen 4 Door Bracket Screws

French Doors

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Top Hinges

t A

A, Hinge Cover Screw

B, Top Hinge Cover

C, s/18"Hex Head Hinge Screws

D. Top Hinge

Bottom Hinges

A. Hinge Pin Cover

B. Bottom Hinge

C. Hinge Screws

Wiring Plug

A. Flat-Head Handle Screws

B. Refrigerator Drawer Handle

A. Flat-Head Handle Screws

B. Freezer Drawer Handle

A, Loosen 4 Door Bracket Screws

The base grille covers the leveling screws and roller assemblies

located at the bottom of the refrigerator cabinet below the freezer

door or drawer. Before making adjustments, remove the base

grille and move the refrigerator to its final location.

1. Remove the two screws fastening the base grille to the

cabinet, and set the screws aside. Grasp the grille and pull it

toward you.

Move the refrigerator to its final location.

NOTE: To allow the refrigerator to roll easier, raise the leveling

legs off the floor by turning the leveling screws

counterclockwise. The front rollers will be touching the floor.

So the doors will close easier, use a V4"hex driver to turn both

leveling screws clockwise. This will raise the front of the

refrigerator tilting it slightly downward to the rear. Turn both

leveling screws the same amount.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws.

A. Leveling screw

B. Front toiler

Open and close the doors to make sure they close as easily as

you like. If not, increase the tilt by turning both leveling screws

clockwise. It may take several turns of the leveling screw to

allow the doors to close easier.

Check for door alignment. If one door is lower than the other,

adjust the leveling screw, on the lower side of the refrigerator.

Using a V4"hex driver, turn the screw clockwise to raise that

side of the refrigerator until the doors are aligned. It may take

several turns of the leveling screw to raise the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws.

6. Make sure the refrigerator is steady. If the refrigerator seems

unsteady or rolls forward when the door or drawer is opened

adjust the leveling screws. Using a V4"hex driver, turn the

leveling screw on each side clockwise until the rollers are up

and the leveling feet are firmly against the floor.

7. Replace the base grille by aligning the holes in the grille with

the holes in the cabinet and fasten using the screws removed

in Step 1.

REFRIGERATORUSE

(F:e_@@es"_x_es}

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

Your model may have either Electronic or Digital Controls.

IM PORTANT:

• Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a

higher (colder) than recommended setting will not cool the

compartments any faster.

The recommended settings should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is

firm.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

For your convenience, the temperature controls are preset at the

factory. When you first install your refrigerator, make sure the

controls are still set to the recommended setting as shown.

Style 1

Recommended Setting "4"

Freezer ScrollDownforCoolingOff Refrigerator

7 J_the _;ddesr recommended setting 4 71s the coldest

Style 2

Recommended Setting "4"

...............I l

Electronic Temperature Control

On • • Off Freezer %c ollDown_o Co@_gOff Refrigerator

.......................... CZ3 CZ3

To Turn Off/On:

Style 1-Press the freezer minus sign touch pad until a

dash (-) appears in both the refrigerator and freezer displays.

Neither compartment will cool.

Style 2-Press the freezer down arrow touch pad until a

dash (-) appears in both the refrigerator and freezer displays.

Neither compartment will cool.

Humidity Control (on some models)

The humidity control turns on a heater to help reduce moisture on

the door hinge seal. Use in humid environments or when you

notice moisture on the door hinge seal. The refrigerator uses more

energy when Humidity Control is on.

• Press the control to ON when the environment is warm and

more humid, or if you notice moisture on the door hinge seal.

• Press the control to OFF to save energy when the environment

is less humid.

HumidityControl

On Off

Adjusting Controls

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart below as

a guide.

To adjust the temperature:

Style 1-Press the up or down arrow touch pads

Style 2-Press the plus or minus sign touch pads.

Except when first turning on the refrigerator, do not adjust the

control more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control

one setting higher

FREEZER too warm/too little ice FREEZER Control one

setting higher

REFRIGERATOR too cold REFRIGERATOR Control

one setting lower

FREEZER too cold FREEZER Control one

setting lower

For your convenience, your temperature controls are preset at the

factory. When you first install your refrigerator, make sure the

controls are still set to the Initial settings as shown.

Initial Settings

OFF Indicates Cooling Is Off OFF Indicates Cooling is Off

O o Recommended 38 ° Recommended

Freezer Refrigerator

IMPORTANT: When the power is on, the temperature display

shows the set point temperature of the compartment.

To Turn Your Refrigerator Off/On:

• Press both the freezer and refrigerator (+) touch pads

repeatedly until "OFF" appears in the displays. Allow a few

seconds for the refrigerator to shut off. Neither compartment

will cool.

• Press both the refrigerator and freezer (-) touch pads to turn

on the refrigerator.

Adjusting Digital Controls

The REFRIGERATOR control adjusts the refrigerator compartment

temperature. The FREEZER control adjusts the freezer

compartment temperature.

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart as a

guide.

To Adjust Set Point Temperatures:

The first touch of the (+) or (-) touch pad displays the current

temperature set point.

• Press the (+) or (-) touch pads until the desired temperature

set point is displayed.

NOTE: Except when first turning on the refrigerator, do not

adjust either temperature control more than one setting at a

time. Wait 24 hours between adjustments for the temperature

to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm Adjust REFRIGERATOR

Control 1° lower

FREEZER too warm/too little ice Adjust FREEZER

Control 1° lower

REFRIGERATOR too cold Adjust REFRIGERATOR

Control 1° higher

FREEZER too cold Adjust FREEZER

Control 1° higher

Additional Digital Control Center Features

PowerCold TM

The PowerCold TM feature assists with periods of high refrigerator

use, full grocery loads, or temporarily warm room temperatures.

• Press the PowerCold TM touch pad to set the freezer and

refrigerator to the lowest temperature settings. Press the

PowerCold TM touch pad again to return to the normal

refrigerator set point.

NOTE: The PowerCold TM feature will automatically shut off in

approximately 12 hours.

Max Ice

The Max Ice feature assists with temporary periods of heavy ice

use by increasing ice production.

• Press the Max Ice touch pad to set the freezer to the lowest

temperature setting. Press the Max Ice touch pad again to

return to the normal freezer set point.

NOTE: When Max Ice is on, the (+) and (-) pads for the freezer

control will not operate. The Max Ice feature will automatically

shut off in approximately 24 hours.

Humidity Control

The Humidity Control feature turns on a heater to help reduce

moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator

uses more energy when Humidity Control is on.

• Press Humidity Control when the environment is warm and

more humid, or if you notice moisture on the door hinge seal.

The indicator light will be lit when humidity control is ON.

• Press Humidity Control to save energy when the environment

is less humid.

press if

moisture

oppears

Temp Alarm

The Temp Alarm feature provides temperature information in the

event of a power outage.

Power outage: During a power outage, if the temperatures in the

refrigerator and freezer compartments exceed normal operating

temperatures, the highest temperature reached will be displayed.

• Press the Temp Alarm touch pad until the indicator light is lit,

to turn on this feature. Press and hold Temp Alarm for

3 seconds until the indicator light goes off to turn off this

feature.

Temp Alarm: An alarm will sound repeatedly if the freezer or

refrigerator compartment temperatures exceed normal operating

temperatures for an hour or more.

The temperature displays will alternately show the current

temperatures and the highest temperatures the compartments

reached.

Press the Temp Alarm touch pad once to stop the audible

alarm and alternating temperature displays. The Temp Alarm

light will continue to flash until the refrigerator returns to the

set temperature.

Door Alarm

The Door Alarm feature sounds a chime every few seconds when

the refrigerator door has been left open for 5 continuous minutes.

The chime will sound until the door is closed or Door Alarm is

turned off.

• Press the Door Alarm touch pad to turn this feature on or off.

The indicator light will be lit when the Door Alarm feature is on.

Filter Reset

The Filter Reset control allows you to restart the water filter status

tracking feature each time you replace your water filter. See

"Water Filtration System."

• Press and hold the Filter Reset touch pad for 3 seconds, until

the Order or Replace light turns off.

order replace

press 3 sec

Digital Control User Preferences

The control center allows you to set user preferences, if desired.

Temperature Display (F_C)

This preference allows you to change the temperature display.

F - Temperature in degrees Fahrenheit

C - Temperature in degrees Celsius

Alarm (AL)

This preference allows you to turn off the sound of all alarms.

ON - You will hear the alarm sound.

OFF - You will not hear the alarm sound.

To Access the User Preferences Menu:

1. Press and hold the Door Alarm touch pad for 3 seconds. The

preference name will appear in the Freezer display and the

preference status (For C) or (ON or OFF) will appear in the

Refrigerator display.

2. Use the Freezer (+) or (-) touch pads to scroll through the

preference names. When the desired preference name is

displayed, press the Refrigerator (+) or (-) touch pads to

change the preference status.

3. Set your preferences by pressing and holding the Door Alarm

touch pad for 3 seconds, or by shutting the refrigerator

compartment door.

III11 II!(IIVli"I

You can control the amount of humidity in the moisture-sealed

crisper. Depending on your model, adjust the control to any

setting between FRUIT and VEGETABLES or LOW and HIGH.

FRUIT/LOW (open) for best storage of fruits and vegetables with

skins.

VEGETABLES/HIGH (closed) for best storage of fresh, leafy

vegetables.

IMPORTANT: Flush the water system before turning on the ice

maker. See "Water Dispenser."

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

NOTE: Turn off the ice maker before removing the ice storage bin

to serve ice or to clean the bin. This will keep the ice cubes from

dropping out of the ice maker and into the freezer compartment.

After replacing the ice storage bin, turn on the ice maker.

Ice Production Rate

The ice maker should produce a complete batch of ice

approximately every 3 hours.

To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Controls." Wait 24 hours

between adjustments.

Remember

Allow 24 hours to produce the first batch of ice. Allow 3 days

to completely fill the ice storage bin. Discard the first three

batches of ice produced.

The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

Do not store anything on top of the ice maker or in the ice

storage bin.

IMPORTANT:

After connecting the refrigerator to awater source or replacing

the water filter, flush the water system. Use a sturdy container

to depress and hold the water dispenser lever for 5 seconds,

then release it for 5 seconds. Repeat until water begins to

flow. Once water begins to flow, continue depressing and

releasing the dispenser lever (5 seconds on, 5 seconds off)

until a total of 4 gal. (15 L) has been dispensed. This will flush

air from the filter and water dispensing system, and prepare

the water filter for use. Additional flushing may be required in

some households. As air is cleared from the system, water

may spurt out of the dispenser.

NOTE: After 5 minutes of continuous dispensing, the

dispenser will stop dispensing water to avoid flooding. To

continue dispensing, press the dispenser button again.

• Allow 24 hours for the refrigerator to cool down and chill

water. Dispense enough water every week to maintain a fresh

supply.

Dispensing Water

1. Hold a container under the dispenser while pressing the

button.

2. Release the button to stop dispensing.

The water filter is located in the upper right-hand corner of the

refrigerator compartment.

REFRIGERATORCARE

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status Lights

When a water filter has been installed in the refrigerator the water

filter status lights will remind you when it is time to order and

replace your water filter.

• The Order light (yellow) will illuminate when 90% of the volume

of water for which the filter is rated has passed through the

filter OR 5 months have passed since the filter was installed.

The Replace light (red) will illuminate when the rated volume of

water has passed through the filter OR 6 months have passed

since the filter was installed. A new water filter should be

installed immediately when the Replace light is illuminated.

The disposable water filter should be replaced at least every

6 months OR earlier if the flow of water to your water dispenser or

ice maker decreases noticeably.

Reset Water Filter Status

After replacing the water filter, press and hold Reset Filter or Filter

Reset (depending on your model) for 3 seconds. The Order and

Replace indicator lights will blink and then go off when the system

is reset. See "Using the Controls."

Replacing the Water Filter

To purchase a replacement water filter, model UKF8001AXX-750

or UKF8001AXX-200, see "Accessories."

IMPORTANT: Air trapped inthe water system may cause water

and filter to eject. Always dispense water for at least 2 minutes

before removing the filter or blue bypass cap.

1. Turn filter counterclockwise to remove.

2. Remove sealing label from replacement filter and insert the

filter end into the filter head.

Turn the filter clockwise until it stops. Snap the filter cover

closed.

Flush the water system. See "Water Dispenser" or "Water and

Ice Dispenser."

NOTE: The dispenser feature may be used without a water filter

installed. Your water will not be filtered. If this option is chosen,

replace the filter with the blue bypass cap.

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT:

Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid

odor transfer and drying out of food, wrap or cover foods

tightly.

For stainless steel models, stainless steel is corrosion-

resistant and not corrosion-proof. To help avoid corrosion of

your stainless steel, keep your surfaces clean by using the

following cleaning instructions.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, muriatic acid,

cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on exterior surfaces (doors and

cabinet), plastic parts, interior and door liners or gaskets. Do not

use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Clean the exterior surfaces.

Painted metal: Wash painted metal exteriors with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately to

avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately to

avoid water spots.

NOTE: When cleaning stainless steel, always wipe in the

direction of the grain to avoid cross-grain scratching.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

t)Ie

IMPORTANT: The light bulbs in both the refrigerator and freezer

compartments of your new refrigerator use LED technology. If the

lights do not illuminate when the refrigerator and/or freezer door is

opened, call for assistance or service. See "Warranty" for phone

numbers.

Unplug the refrigerator or disconnect power.

Remove the light shield (on some models).

• Top of the refrigerator compartment - Slide the light shield

toward the back of the compartment to release it from the

light assembly.

Replace the burned-out LED bulb(s) with a bulb of the same

size, shape and wattage.

• To replace the burned-out LED bulb with an LED bulb,

order Part Number W10565137 (3.6 watts).

NOTE: Some LED replacement bulbs are not

recommended for wet/damp environments. The

refrigerator and freezer compartments are considered to

be wet/damp environments. If using a brand of LED bulb

other than the recommended LED bulb, before

installation, read and follow all instructions on the LED

packaging.

If an incandescent bulb is used to replace an LED bulb,

use only incandescent bulbs for household appliances

with a maximum of 40 watts.

4. Replace the light shield.

5. Plug in refrigerator or reconnect power.

Vacations

If You Choose to Leave the Refrigerator On While You're

Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker, and is

connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the

water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.

NOTE: Depending on your model, raise the wire shutoff arm to

OFF (up) position, or press the switch to OFE

4. Empty the ice bin.

If You Choose to Turn Off the Refrigerator Before You

Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or press the switch to OFF,

depending on your model.

3. Turn off the Temperature control(s). See "Using the Control(s)."

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or press the switch to OFF,

depending on your model.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Turn off the Temperature control(s). See "Using the Control(s)."

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it

rolls more easily OR raise the leveling screws so they don't

scrape the floor. See "Adjust the Door(s)" or "Door Closing

and Door Alignment."

9. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer to

the "Installation Instructions" section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,

refer to the warranty page in this manual and scan the code with your mobile device, or visit www.maytag.com/product_help.

In Canada, visit www.maytag.ca.

In the U.S.A.: In Canada:

Maytag Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Maytag Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

The refrigerator will not operate The refrigerator seems noisy

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below are

listed some normal sounds with explanations.

• Buzzing - heard when the water valve opens to fill the ice

maker

Pulsating - fans/compressor adjusting to optimize

performance

Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator

Sizzling/Gurgling - water dripping on the heater during

defrost cycle

Popping - contraction/expansion of inside walls, especially

during initial cool-down

Water running - may be heard when ice melts during the

defrost cycle and water runs into the drain pan

Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

Power cord unplugged? Plug into a grounded 3 prong outlet.

Is outlet working? Plug in a lamp to see if the outlet is

working.

Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. Ifthe problem continues,

call an electrician.

Are controls on? Make sure the refrigerator controls are on.

See "Using the Control(s)."

New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct

position.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

Temperature is too warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Control(s)."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

The ice maker is not producing ice or not enough ice

Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

Freezer door closed completely? Firmly close the freezer

compartment door. If the freezer compartment door will not

close all the way, see "The doors will not close completely,"

earlier in this section.

Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice volume improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice quality improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

Odor transfer from food? Use airtight, moisture proof

packaging to store food.

Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

Water filter installed on the refrigerator? Gray or dark

discoloration in ice indicates that the water filtration system

needs additional flushing. Flush the water system before using

a new water filter. Replace water filter when indicated. See

"Water Filtration System."

The water dispenser will not operate properly

Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

Kink in the water source line? Straighten the water source

line.

New installation? Flush and fill the water system. See "Water

Dispenser."

Is the water pressure at least 35 psi (241 kPa)? The water

pressure to the home determines the flow from the dispenser.

See "Water Supply Requirements."

Water filter installed on the refrigerator? Remove filter and

operate dispenser. If water flow increases, the filter may be

clogged or incorrectly installed. Replace filter or reinstall it

correctly.

Refrigerator door closed completely? Close the door firmly.

If it does not close completely, see "The doors will not close

completely," earlier in this section.

Recently removed the doors? Make sure the water

dispenser wire/tube assembly has been properly reconnected.

See "Refrigerator Door(s) and Drawer."

Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

Water is leaking from the dispenser system

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough?

Hold the glass under the dispenser 2 to 3 seconds after

releasing the dispenser lever.

New installation? Flush the water system. See "Water

Dispenser."

Recently changed water filter? Flush the water system. See

"Water Dispenser."

Water on the floor near the base grille? Make sure the water

dispenser tube connections are fully tightened. See

"Refrigerator Door(s) and Drawer."

Water from the dispenser is warm

NOTE: Water from the dispenser is only chilled to 50°F (10°C).

• New installation? Allow 24 hours after installation for the

water supply to cool completely.

Recently dispensed large amount of water? Allow 24 hours

for water supply to cool completely.

Water not been recently dispensed? The first glass of water

may not be cool. Discard the first glass of water.

Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See "Water

Supply Requirements."

The following accessories are available for your refrigerator. To

order an accessory, contact us and ask for the part number.

In the U.S.A., visit our webpage www.maytag.com/accessories

or call 1-800-901-2042.

In Canada, visit our webpage www.maytag.ca

or call 1-800-807-6777.

affresh®Stainless Steel Cleaner:

In U.S.A., order Part #W10355016

In Canada, order Part #W10355016B

affresh ®Stainless Steel Wipes:

In U.S.A., order Part #W10355049

In Canada, order Part #W10355049B

affresh ®Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010

In Canada, order Part #W10355010B

Water Filter:

Order Part #UKF8001AXX-750 or Part #UKF8001AXX-200

Produce Preserver (on some models):

Order Part #W10346771A

WATERFILTERCERTIFICATIONS

State of California

Department of Public Health

WaterTreatmentDevice

CertificateNumber

03- 1583

Date Issued: September I6, 2008

Date Re_,ised: April 22, 2009

TrademarldModeluKF8001AXX-750Designation

46 9006-750 ....

67003523-750

IVlanulacturer: Cuno 1_ :

The water treatmen{ _vi_g)(tiled on this certificate have

State of California

Department of Public Health

WaterTreatmentDevice

CertificateNumber

09- 1979

Date Issued: May 8, 2009

Date Revised: 6/22/2010

Tradenlark Model Designation

UKF800I AXX-200

Kenmore 46 90tg_-2110

Replacement Elements

UKi8001

aa unn,,

Vlanuliteturer: 3M Puriflcanon

Cysts )

"lurbidity )

Organic Contaminants

Awazine ?

Lindane

B_u_ene )

Carbolhmn \ ( )

p-dichlorobenzene ;

Toxaphene

Tetmchtoroethylene

Rated Service Capacity: 750 gaI Rated Service Flow: 078 gpm

Conditions of Certification:

Do not use where water is microbiologically unsal_ or with water of unknown quality, except that systems certified

fbr cyst reduction nmy be used on disinfected waters that may contahl filterable cysts.

Endrin

Ethvibenzene

Lindanc

Rated Service Capacity: 200 gal Rated Service Flow: 0.55 _Lpln

Conditions of CertilicatioiL'

Do not use where water is microbiologically tmsafe _r With wa_er of unkno_n quality, except that systems

certified for c_st reduction rna_ be used on distributed waters that may contain filterable cysts.

PERFORMANCEDATASHEETS

Interior Water Filtration System

Model UKF8001AXX-750 Capacity 750 Gallons (2839 Liters)

System tested and certified by NSF International against NSF/ANSI Standard 42 for the

reduction of Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI

Standard 53 for the reduction of Lead, Mercury, Atrazine, Benzene, p-Dichlorobenzene,

Carbofuran, Toxaphene, Cysts, Turbidity, Asbestos, Tetrachloroethylene and Lindane.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 2.00 mg/L 2.0 mg/L + 10% 0.06 mg/L 0.050625 mg/L 97.00% 97.52%

Particulate Class I* 85% reduction 14,000,000 #/mL Atparticles/mLleast10,000 370,000 #/mL** 196,666 #/mL 97.40% 99.00%

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction

Lead: @ pH 6.5 0.010 mg/L 0.150 mg/U 0.15 mg/L + 10% < 0.001 mg/L < 0.001 mg/L >99.30% >99.30%

Lead: @ pH 8.5 0.010 mg/L 0.150 mg/U 0.15 mg/L _+10% < 0.001 mg/L < 0.001 mg/L >99.30% >99.30%

Mercury: @ pH 6.5 0.002 mg/L 0.006 mg/L 0.006 mg/L + 10% 0.0005 mg/L 0.0003 mg/L 91.70% 95.00%

Mercury: @ pH 8.5 0.002 mg/L 0.0059 mg/L 0.006 mg/L _+10% 0.0018 mg/L 0.00073 mg/L 69.20% 88.10%

Benzene 0.005 mg/L 0.0133 mg/L 0.015 mg/L _+10% 0.0005 mg/L 0.0005 mg/L 96.10% 96.30%

p-Dichlorobenzene 0.075 mg/L 0.210 mg/L 0.225 mg/L _+10% < 0.0005 mg/L < 0.0005 mg/L >99.80% >99.80%

Carbofuran 0.040 mg/L 0.0753 mg/L 0.08 mg/L _+10% 0.027 mg/L 0.008 mg/L 64.60% 73.45%

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 _+10% < 0.001 mg/L < 0.001 mg/L >93.3% >93.3%

Atrazine 0.003 mg/L 0.0102 mg/L 0.009 mg/L _+10% 0.0027 mg/L 0.00105 mg/L 76.30% 89.40%

Asbestos >99% 126.5 MF/L 107to 108fibers/l_ tt < 0.17 MF/L < 0.17 MF/L >99.99% >99.99%

Live Cysts _ >99.95% 122,500 #/L 50,000/L min. < 1 #/U < 1 #/U >99.99% >99.99%

Turbidity 0.5 NTU 10.5 NTU 11 _+1 NTU 0.30 NTU 0.125 NTU 97.30% 98.80%

Lindane 0.0002 mg/L 0.0019 mg/L 0.002 _+10% < 0.00016 mg/L 0.000035 mg/L 91.80% 97.90%

Tetrachloroethylene 0.005 mg/L 0.015 mg/L 0.015 mg/L _+10% < 0.0005 mg/L < 0.0005 mg/L >96.6% >96.6%

Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.78 gpm (2.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F _+5°F

(20°0 _+3°0).

• It is essential that operational, maintenance, and filter •

replacement requirements be carried out for the product to

perform as advertised.

• The disposable water filter should be replaced at least every

6 months.

The filter monitor system measures the amount of water that

passes through the filter and alerts you to replace the filter.

When 90% of the filter's rated life is used, the yellow (Order)

light comes on. When 100% of the filter's rated life is used, the

red (Replace) light comes on, and it is recommended that you

replace the filter. For models without filter status lights,

replace the filter every 6 months. Use replacement filter

model UKF8001. 2014 suggested retail price of

$44.99 U.S.A./S49.95 Canada. Prices are subject to change

without notice.

The product is for cold water use only.

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

Refer to the "Water Filtration System" section for the

Manufacturer's name and telephone number.

Refer to the "Warranty" section for the Manufacturer's limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well

Water Pressure 35 - 120 psi (241 - 827 kPa)

Water Temperature 33° - 100°F (1o_38oC)

Service Flow Rate 0.78 gpm (2.9 L/min.) @60 psi

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

tThese contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

ttFibers greater than 10 um in length

_Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

Interior Water Filtration System

Model UKF8001AXX-200 Capacity 200 Gallons (757 Liters)

System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of

Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSl Standard 53 for the reduction of

Lead, Mercury, Atrazine, Benzene, p-Dichlorobenzene, Carbofuran, Toxaphene, Cysts, Turbidity,

Asbestos, O-Dichlorobenzene, Ethylbenzene, Chlorobenzene, Endrin, Tetrachloroethylene and Lindane.

This system has been tested according to NSF/ANSl Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSl Standards 42 and 53.