Yamaha SV150S El manual del propietario

Marca: Yamaha

Modelo: SV150S

Tipo: El manual del propietario

Este manual también es adecuado para

SV150

Thank you for purchasing the Yamaha SILENT Violin

. In order to obtain the

maximum performance and enjoyment from your SILENT Violin

, we urge

you to read this Owner’s Manual thoroughly before using the instrument.

Please keep this Owner’s Manual in a safe place for later reference.

Precautions ................................................................... 3

Main Body/Accessories ............................................... 4

Nomenclature ................................................................ 5

Setup .............................................................................. 8

■

Tuning and Changing the Strings ................................................ 8

■

The Shoulder Rest ................................................................... 10

■

The Bow (supplied with the SV150S) ........................................ 10

■

About the Soft Case (SV150S Accessory) ................................ 10

Usage ............................................................................ 11

■

Sound Output Basics ................................................................ 11

■

Using the Built-In Tuner ............................................................. 11

■

Using the Built-In Metronome .................................................... 12

■

Using the Built-In Effects ........................................................... 12

■

Using the Music Player .............................................................. 14

■

Messages .................................................................................. 16

Power Supply .............................................................. 17

■

Using Batteries ......................................................................... 17

■

Supplying AC Power ................................................................. 17

Speciﬁcations ............................................................. 18

SV150/SV150S

Owner’s Manual

Contents

MPEG Layer-3 audio coding technology licensed

from Fraunhofer IIS and Thomson.

English

02_SV150S_En_R3.indd 1 14/01/23 13:51

SPECIAL MESSAGE SECTION

92-BP

This product utilizes batteries or an external power supply (adaptor). DO NOT

connect this product to any power supply or adaptor other than one described

in the manual, on the name plate, or speciﬁcally recommended by Yamaha.

This product should be used only with the components supplied or; a cart,

rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please

observe all safety markings and instructions that accompany the accessory

product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained

in this manual is believed to be correct at the time of printing. However, Yama-

ha reserves the right to change or modify any of the speciﬁcations without

notice or obligation to update existing units.

Do not attempt to service this product beyond that described in the user-

maintenance instructions. All other servicing should be referred to qualiﬁed

service personnel.

This product, either alone or in combination with an ampliﬁer and headphones

or speaker/s, may be capable of producing sound levels that could cause

permanent hearing loss. DO NOT operate for long periods of time at a high

volume level or at a level that is uncomfortable. If you experience any hearing

loss or ringing in the ears, you should consult an audiologist.

IMPORTANT:

The louder the sound, the shorter the time period before dam-

age occurs.

NOTICE:

Service charges incurred due to a lack of knowledge relating to

how a function or effect works (when the unit is operating as designed) are

not covered by the manufacturer’s warranty, and are therefore the owner’s re-

sponsibility. Please study this manual carefully and consult your dealer before

requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are

both user safe and environmentally friendly. We sincerely believe that our

products and the production methods used to produce them meet these goals.

In keeping with both the letter and the spirit of the law, we want you to be

aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery

which (if applicable) is soldered in place. The average life span of this type

of battery is approximately ﬁve years. When replacement becomes necessary,

contact a qualiﬁed service representative to perform the replacement.

This product may also use “household” type batteries. Some of these may be

rechargeable. Make sure that the battery being charged is a rechargeable type

and that the charger is intended for the battery being charged.

When installing batteries, do not mix old batteries with new, or with batteries of

a different type. Batteries MUST be installed correctly. Mismatches or incorrect

installation may result in overheating and battery case rupture.

Warning:

Do not attempt to disassemble or incinerate any battery. Keep all

batteries away from children. Dispose of used batteries promptly and as regu-

lated by the laws in your area. Note: Check with any retailer of household type

batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or

for some reason its useful life is considered to be at an end, please observe all

local, state, and federal regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please

contact Yamaha directly.

NAMEPLATE LOCATION:

The nameplate is located on the bottom of the

product. The model number, serial number, power requirements, etc., are

located on this plate. You should record the model number, serial number, and

the date of purchase in the spaces provided below and retain this manual as a

permanent record of your purchase.

Model Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

FCC INFORMATION (U.S.A.)

tronic devices. Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this product is

found to be the source of interference, which can be determined by

turning the unit “OFF” and “ON”, please try to eliminate the problem

by using one of the following measures:

Relocate either this product or the device that is being affected by the

interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the antenna.

If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to

co-axial type cable.

If these corrective measures do not produce satisfactory results, please

contact the local retailer authorized to distribute this type of product.

If you cannot locate the appropriate retailer, please contact Yamaha

Corporation of America, Electronic Service Division, 6600 Orangeth-

orpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions contained

in this manual, meets FCC requirements. Modiﬁcations not expressly

approved by Yamaha may void your authority, granted by the FCC, to

use the product.

2. IMPORTANT

When connecting this product to accessories

and/or another product use only high-quality shielded cables. Cable/

s supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reasonable

level of assurance that your use of this product in a residential envi-

ronment will not result in harmful interference with other electronic

devices. This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the user’s

manual, may cause interference harmful to the operation of other elec-

CANADA

THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B” LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS

SET OUT IN THE RADIO INTERFERENCE REGULATION OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS.

LE PRESENT APPAREIL NUMERIQUE N’EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES AUX AP-

PAREILS NUMERIQUES DE LA “CLASSE B” PRESCRITES DANS LE REGLEMENT SUR LE BROUILLAGE RADIO ELECTRI QUE EDICTE PAR

LE MINISTERE DES COMMUNICATIONS DU CANADA.

• This applies only to products distributed by Yamaha Canada Music Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.

02_SV150S_En_R3.indd 2 14/01/23 13:51

Your SILENT Violin™ will give you years of reliable service if you follow the simple

rules given below:

■

Location

Do not expose it to the following conditions to avoid

deformation, discoloration, or more serious damage.

• Direct sunlight (e.g. near a window).

• High temperatures (e.g. near a heat source,

outside, or in a car during the daytime).

• Excessive humidity.

• Excessive dust.

• Strong vibration.

■

Power Supply

• Turn the power switch OFF when not in use.

• If you use an AC power adaptor, unplug the adap-

tor from the AC outlet if not to be used for an

extended period of time.

• Unplug the AC power adaptor during electric

storms.

• Avoid plugging the AC power adaptor into the

same AC outlet as appliances with high power

consumption, such as electric heaters or ovens.

Also avoid using multi-plug adaptors since these

can result in reduced sound quality and possibly

damage.

■

Turn Power OFF When Making Connections

• To avoid damage to the SILENT Violin™ and

other devices to which it is connected (a sound

system, for example), turn the power switches

of all related devices OFF prior to connecting or

disconnecting audio cables.

■

Handling and Transport

• Never apply excessive force to the controls, con-

nectors or other parts.

• Always unplug cables by gripping the plug ﬁrmly,

not by pulling on the cable.

• Disconnect all cables before moving the unit.

• Physical shocks caused by dropping, bumping,

or placing heavy objects on the unit can result in

scratches and more serious damage.

■

Cleaning

• Clean the cabinet and panel with a dry soft cloth.

• A slightly damp cloth may be used to remove

stubborn grime and dirt.

•

Never use cleaners such as alcohol or thinner.

• Avoid placing vinyl objects on top of the unit (vinyl

can stick to and discolor the surface).

■

Electrical Interference

• This unit contains electric circuitry and may

cause interference if placed too close to radio or

television receivers. If this occurs, move it further

away from the affected equipment.

YAMAHA is not responsible for damage

caused by improper handling or operation.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them

to applicable collection points, in accordance with your national legislation and the Directives

2002/96/EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and

prevent any potential negative effects on human health and the environment which could otherwise

arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact

your local municipality, your waste disposal service or the point of sale where you purchased the

items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for

further information.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please

contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

02_SV150S_En_R3.indd 3 14/01/23 13:51

Main Body/Accessories

After opening the packaging, please check that all the parts listed below are included.

The following items are in addition to the SV150 package.

SV150

• Main Unit x 1

(The instrument is shipped from the factory with

its bridge removed.)

• Cable x 1

(Connects the instrument to the

Control Box.)

• Stereo earphones x 1

• Bow : 4/4 size x 1

• Bridge x 1

• Rosin : PIRASTRO Schwarz 9005 x 1

• Control Box x 1

SV150S

* AC adaptor is optional, please purchase the optional power adaptor PA-D05K.

* To play SV150/SV150S, you will need 2 SUM-3 (AA) size batteries.

• SD Card x 1

• Soft Case x 1

• Owner’s Manual

(this booklet)

x 1

• “Let’s Enjoy Yamaha SILENT

Violin™” x 1

(booklet with practice pieces)

02_SV150S_En_R3.indd 4 14/01/23 13:51

Nomenclature

Fingerboard

Neck

Chin rest

[Main Unit]

Tuning peg

Nut

4th string (G)

Adjuster

Frame

Tailpiece

Body

Bridge seat

●

Front

●

Back

3rd string (D)

2nd string (A)

1st string (E)

Bridge

Neck

Volume

Shoulder

Rest Holder

Control Box Instru-

ment Jack

02_SV150S_En_R3.indd 5 14/01/23 13:51

[Control Box]

* For use with the SV150. Not compatible with other instruments.

Volume (VOL/MUTE)

Instrument Jack

PHONES

LINE OUT

To the AUX IN jack, etc.

Push

Mute Cancel

Louder

Quieter

Unlock

Hold

Main Volume

Main Unit

Stereo Earphones

External Audio Device

Audio Amp → Speaker

P.A, Mixer, Recording Mixer

Hold Switch (HOLD)

SD Card Slot

SD Card

Select Buttons

Cue Buttons

(–, ENTER, +)

Power Button

(POWER)

LCD Panel

Power Adaptor Jack

(DC 5V 500 mA)

Electric

Outlet

* A Y-cable (sold separately)

that splits the stereo mini

plug into two monaural lines

is required to send the

stereo output to a mixer, etc.

Power Adaptor

(Option)

02_SV150S_En_R3.indd 6 14/01/23 13:51

[Explanation of Input/Output Section]

●

Control Box Instrument Jack

This jack is used to receive power from

the Control Box and transmit the audio

signal from the instrument to the Control

Box. Use the supplied cable to connect

the instrument to the “Instrument Jack” on

the Control Box.

* A commercially available audio cable with

stereo mini plugs on both ends can also be

used. (Cables with resistors are not com-

patible.)

* The system will not operate properly if a

monaural cable is used.

* The system will not operate properly if the

cable is attached to anything other than the

Control Box.

●

Instrument Jack

This jack supplies power to the SV150

instrument and receives the audio signal

from the SV150. Use the supplied cable to

connect the instrument to the “Instrument

Jack” on the Control Box.

●

PHONES Jack

For connecting the supplied inner ear-

phones. Any commercially available head-

phones or inner earphones can be used.

●

LINE OUT Jack

Connecting one end of a commercially

available audio cable with a stereo mini

plug (sold separately) here, sends the ste-

reo audio output of the SILENT Violin™,

complete with effects and functions, to an

external audio device such as an amp, etc.

The violin and the click tone are heard in

the center, while the effects, depending

upon the effect type, are heard in stereo.

The audio signal from the SD card is out-

put according to the original ﬁle recording.

●

SD Memory Card Slot

Inserting the supplied SD memory card

into the slot here allows playback the fol-

lowing music ﬁles. (Refer to page 14 for

more information.)

• Compatible Music Files

Extension File Type

.aac AAC ﬁle compression

.m4a MPEG4 ﬁle compression

.mp3 MPEG1 Audio-Layer-3 ﬁle

compression

.wav Windows standard

(no ﬁle compression)

.mid MIDI File

• Do not listen for extended periods of time at loud volume levels using the inner earphones or head-

phones. Doing so can result in damage to your hearing.

• If the sound is distorted, use the volume control on the instrument or on the Control Box and lower the

volume until the sound is no longer distorted.

• Connect or disconnect the cable between the SILENT Violin™ and the Control Box only after the Control

Box power is switched OFF.

• When connecting the SILENT Violin™'s Control Box to an external device, make sure that the power is

switched OFF on all devices, or that the volume on all devices is set to the minimum level. Loud volume

levels can damage your hearing, and damage equipment.

• Disconnecting the cable while the power is ON may result in damage to the equipment. The sudden

shock to your ears may be severe, so please use caution.

• When making connections to external devices, make sure that the proper plugs are used and securely

connected.

Caution



Never connect any devices (in-

cluding other SILENT Violins™

with different model numbers)

other than the SV150 SILENT

Violin™ that is included in the

bundled set.

Doing so may result in damage to

the other device.

02_SV150S_En_R3.indd 7 14/01/23 13:51

Caution

Set up

■

Tuning and Changing the Strings

The SILENT Violin™ is shipped from the factory with

the bridge unfitted. First, set up the bridge and then

proceed with tuning. As the strings get old, sound qual-

ity will gradually decrease, and it will become difﬁcult to

tune the instrument. Change the strings as soon as you

think they are getting old.

• The end of the strings are sharp and can cut ﬁngers. Use

caution when changing strings.

• When changing or adjusting strings, do not put your face

close to the instrument. The string may suddenly break re-

sulting in eye or other unexpected injuries.

• The lower side of the bridge supports the 1st string (E), the

higher side supports the 4th string (G). Make sure the bridge

is placed properly, then set the bridge in the bridge seat. The

side of the bridge with the logo imprint should face the tail-

piece.

• Ensure that the bridge stands vertically. If it leans to one side,

use both hands to adjust. Make sure that each string passes

over the corresponding slits in the bridge.

[Bridge is placed vertically]

[Make sure that the strings do not

come out of their grooves]

Protective tube on

the 1st (E) string

Correct

Bridge seat

Tailpiece

Body

Bad

Vertical

Bridge seat

Bridge feet

[Make sure the bridge feet do not

come in contact with the bridge seat]

1st string

4th string

[Looking from the tailpiece]

Groove

Logo imprint

Make sure that the strings are resting in

their appropriate grooves in the bridge when

playing the instrument.

Strings may come out of their grooves when adjusting the bridge

or changing strings. Since the ﬁrst (E) and fourth (G) strings tend

to come out of their grooves easily, use your ﬁngers to hold the

strings gently in place when tuning the instrument.

Also, the 1st (E) string is ﬁtted with a protective tube. Make sure

that the tube rests on the bridge.

Always make sure that the bridge is standing vertically,

whether the instrument is being played or stored.

Even if the bridge is standing vertically before tuning, it may tilt

during the tuning process. If so, readjust the bridge so it stands

vertically.

It is very important that the bridge stands vertically. If it leans in

either direction it will impair the sound and risk damaging the

instrument.

02_SV150S_En_R3.indd 8 14/01/23 13:51

1st string (E)

4th string (G)

2nd string (A)

3rd string (D)

●

Winding the Strings

(Please refer to this section when changing the strings)

Before you string the instrument, set the adjuster so that it is in

the middle of its adjustment range. (All adjusters)

Place the ball (on the end of the string) in the notch on the ad-

juster. Make sure the ball is properly inserted in the adjuster’s

notch.

Insert the other end of the string into the hole on the tuning peg. Rotate the tuning peg. As shown in

the illustration, wind the string on the side away from the peg handle once around the peg, then return

the string back overlapping that wind so that the remaining slack is wound gradually toward the peg

handle. 1st (E) and 2nd (A) strings are shown on the left, 3rd (D) and 4th (G) strings on the right.

Adjuster’s notch

String

Ball

The adjuster

should be set to

the middle of its

adjustment range.

Rotate the

tuning peg

as shown

Rotate the

tuning peg

as shown

1st string (E)

4th string (G)

2nd string (A)

3rd string (D)

Winding the 1st

and 2nd strings

Remaining

winds

1st

wind

Winding the 3rd

and 4th strings

1st

wind

Remaining

winds

If the adjuster is too loose, it could produce

noise while playing.

• The strings are tuned to the following pitches. The 1st

string is tuned to E, the 2nd string to A, the 3rd string to

D, and the 4th string to G.

Using the Tuner function on the Control Box (

→

11), push in on the peg while turning to tune.

• Finally, use the adjuster to ﬁne tune the strings.

Don’t loosen

too much.

• When the instrument is not going to be used for an extended period of time, loosen the strings until

the pitch drops a whole tone.

• Before using the instrument, make sure that the bridge is positioned vertically. Damage to the bridge

and poor sound quality may result if the bridge is not properly positioned.

Caution

02_SV150S_En_R3.indd 9 14/01/23 13:51

Bow hair

Rotate the screw

to adjust the bow

hair tension.

Shoulder rest

■

The Shoulder Rest

A commercially available violin shoulder rest (4/4 size) can be

attached to the instrument.

■

The Bow (supplied with the SV150S)

•

(When the winding is covered with a clear wrap)

This ﬁlm pre-

vents discoloration and prevents loosening of the winding due to

shrinkage during drying (except on carbon bows).

Do not remove

the clear wrap.

• Apply rosin to the bow hairs before using. Before using the bow for

the first time, apply rosin carefully and evenly to the whole bow.

From the 2nd time, apply a small amount of rosin to the bow hairs.

• Before using the bow, rotate the screw shown in the illustration so that the bow hairs become taut. The bow

stick should be concave and the bow hairs should have medium tension and be evenly taut. If the bow hairs

and bow stick are parallel, the bow is too tight and this may result in damage or trouble to the bow.

• After use, make sure to loosen bow tension. Also, if powdered rosin has accumulated on the bow stick,

wipe the bow stick with a soft cloth to remove the rosin.

Winding

• The bow’s shape can make it a danger to persons and objects close by. When playing the instrument

make sure sufﬁcient space is provided between you and the next person or object, etc. Never treat the

bow in a rough manner, such as swinging or throwing the bow.

■

About the Soft Case (SV150S Accessory)

The accessory soft case is designed for use with this particular instrument. It is designed to

hold the instrument, Control Box, and your own shoulder rest.

The bow case can also be detached and used. When the bow case is removed, pull out the belt

attached to the back of the bow case, and attach it to the soft case as shown in the diagram.

• The case is designed for carrying the instrument. It is not designed to protect the instrument from impacts.

Do not expose the instrument to impact or strong pressure while carrying or storing the instrument.

• Remove the shoulder rest before placing the instrument in the soft case.

Stereo Inner Earphones,

Cable, Rosin, etc.

Instrument

Bow Case

Shoulder rest

Control Box

Belt

•

Make sure that the bow hair is sufﬁ ciently loosened

before placing the bow in the case.

• Before storing any bow in the case other than the one

that came with the instrument, make sure its length al-

lows for proper and secure storage in the case.

02_SV150S_En_R3.indd 10 14/01/23 13:51

Usage

■

Sound Output Basics

First, connect the instrument to the Control Box using the supplied cable.

Connect the supplied stereo inner earphones to the jack with the

mark.

To reproduce sound from an external audio device, use a cable that matches the input jack on the audio

device and connect it to the instrument’s LINE OUT jack.

Press and hold the power button on the Control Box for about 1 second to switch the power ON and

light the LCD display.

* The power will not switch ON if the HOLD switch is in the lower position. Slide the HOLD switch

to the upper position and press the POWER button again.

* To switch the power off, hold the POWER button for more than 2 seconds.

The volume is controlled with the volume control on the instrument, and the VOL/MUTE dial on the

Control Box. The volume control on the instrument only adjusts the instrument’s volume, while the

VOL/MUTE dial on the Control Box adjusts the overall volume level (0 to 30) of the violin plus the ef-

fect/metronome/player.

* This instrument will not produce any sound if the volume control on the instrument is set to “0”.

* Pressing the VOL/MUTE dial engages the mute function and displays the icon ( ). Press the

VOL/MUTE dial again disengages the mute and the headphones icon (

) reappears.

* When the HOLD switch is set to its lower position, none of the buttons on the Control Box will

operate.

■

Using the Built-In Tuner

Connect the instrument to the Control Box and make the

proper settings as described in the previous “Sound Output

Basics” section.

Press the TUNER button on the Control Box, and call up the

display shown on the right.

Using the + and – buttons, set the standard pitch (A=430 to

450 Hz).

Play a string and its note name will appear in the lower cen-

ter of the display. The tuner will indicate whether the note

played on the instrument is ﬂat/lower

, or sharp/higher

. The meter section indicates how far off the pitch is.

When the note is in tune both the

and

icons appear,

and the meter stops at the “0” position in the center.

Also, pressing the ENTER button plays a tuning note that

corresponds to the set standard pitch (A note). Press the EN-

TER button once again to stop playback of the tuning note.

Standard Pitch

Meter Display

(Cent)

Note

Sharp

Flat

[When the note is in tune: C]

02_SV150S_En_R3.indd 11 14/01/23 13:51

■

Using the Built-In Effects

The SV150 SILENT Violin™ features a built-in DSP (Digital Signal Processor) that can be

used to add any of the processor’s 24 effects including reverb to make playing more enjoy-

able.

Effect name

Parameter: Selected Value

As described in the previous “Sound Output Basics” sec-

tion, connect the instrument to the Control Box and make

the proper settings.

Press the SOUND button on the Control Box to call up

the display shown on the right.

Using the + and – buttons, select an EFFECT (No. 1-25)

* Effect “No. 25 No Effect” switches the effect OFF.

If a parameter appears below the effect name, press the

SOUND button to select the parameter, then use the +/–

buttons to set the parameter value.

* Holding the + or – button changes the value continu-

ously. Also, pressing the + and – buttons simultane-

ously reverts the value to its factory default value.

Effect No.

Tempo

Volume

Beat

■

Using the Built-In Metronome

* The built-in metronome operates even if the instrument is not connected to the Control Box, and

can be heard through the stereo inner earphones or through the LINE OUT jack.

Press the METRONOME button on the Control Box to

call up the display shown at the right.

Press the METRONOME button to select the item you

want to set in the display, then use the +/– buttons to set

the value.

* Holding the + or – button changes the value continu-

ously. Also, pressing the + and – buttons simultane-

ously reverts the value to its factory default value.

= Sets the quarter note tempo (32-280). The

default value is 120.

Beat: Sets the beat (0-7 beats, 8-beat, triplet, 16-

beat). The default value is 4-beat.

Volume: Sets the volume level (0-30). The default

value is 20.

Press the ENTER button to start the metronome. Press

the button again to stop the metronome.

02_SV150S_En_R3.indd 12 14/01/23 13:51

No.

Effect Name Parameter

Range

Description

(Default)

1 Studio — — Natural room reverberation. Basic sound for practicing.

2 Large Hall — — Large hall reverberation with long decay.

3 Middle Hall — — Medium-sized hall reverberation.

4 Small Hall — — Small hall reverberation with short decay.

5 Club — — Reverberation typical of a small jazz club.

6 Jazz — — Effect based on a jazz violin recorded with a microphone.

7 Fantasy Feedback 64–127 (116) Reverb and delay are used to create a dreamy atmosphere.

Feedback adjusts the number of delays.

8 Mirror Room Feedback 64–127 (116)

Produces mirror-like sound reﬂections. Feedback adjusts the

number of delays.

9 Chorus Depth 24–127 (72) Chorus effect adds depth to the sound. Depth adjusts the

intensity of the effect.

10 Strings Effect Level 10–100 (40) Sounds like a string section of 2 or more players playing

simultaneously. Effect Level adjust the thickness of the

sound.

11 Vibrato Speed 40–104 (83) Simulates the vibrato typical of a classical performance.

Speed adjusts the vibrato rate.

12 Lazy Depth 32–127 (127) A very lazy feeling. Depth adjusts the intensity of the effect.

13 Under the Sea Speed 0–92 (4) A mysterious underwater or tunnel type effect. Speed

changes the tone.

14 Planet Depth 32–127 (94) Alien worlds come to mind. Depth adjusts the intensity of

the effect.

15 Pan Reverb Reverb Time 6–53 (36) Sound shifts between left and right sides. Reverb Time

adjusts the length of the effect.

16 Pan Chorus Speed 8–84 (55) Auto pan + rich chorus sound shifts quickly from left to right

like a car speeding down the highway. Speed adjusts the

speed of the shifting sound.

17 Auto Wah Speed 5–90 (17) Changes the tone automatically. Speed adjusts the speed

of the tone change.

18 Over Drive Tone 34–58 (46) Light distortion. Tone adjusts brightness and projection.

19 Delay Drive Delay Level 0–92 (24) Distorted sound with delay. Delay level adjusts the amount

of effect.

20 Buzz Drive Tone 34–58 (46) Ring modulation and distortion create a unique effect. Tone

adjusts brightness and projection.

21 Wah Drive Over Drive 2–18 (8) Combines Auto Wah and Overdrive effects. Overdrive

adjusts the amount of distortion.

22 Jet Tone 34–58 (46) Creates a jet sound made popular in 70’s rock music. Tone

adjusts brightness and projection.

23 Chorus Lead Tone 34–52 (46) Chorus and Overdrive effects create a punchy lead solo

tone. Tone adjusts brightness and projection.

24 Tube Drive Tone 34–52 (46) Amp simulation creates a heavily distorted tone. Tone

adjusts brightness and projection.

25 No Effect — — No effect is produced. Use this setting when external

effectors are being used.

●

Effect List

02_SV150S_En_R3.indd 13 14/01/23 13:51

■

Using the Music Player

The Control Box has a built in music player that can play music ﬁles (.aac, .m4a, .mp3,

.wav, .mid) from an SD card.

* Refer to page 7 for more information on each of the music ﬁle formats.

* You can listen to music playback through the inner earphones or the LINE OUT jack even if

when the instrument is disconnected.

●

Preparing Music Files

Copy the music ﬁle to the SD card using a computer with an SD card reader.

* The player is compatible with SD cards of up to 2GB (it is not compatible with SDHC cards).

Use a computer running a commercially available or freeware application to convert the song data from

your CD collection, music ﬁles you've downloaded from the Internet, etc., to one of these compatible

ﬁle formats (.aac, .m4a, .mp3, .wav).

Insert the SD card into the computer to copy the converted music ﬁles to the SD card.

Playback Speed

Playback Volume

File Name

Playback Icon

Elapsed Time

Folder Mark

Press the PLAYER button to highlight the File Name ﬁeld, then use the +/– buttons to select the music

ﬁle for playback. Music ﬁles that can be played are displayed in alphabetical order.

Music data from CDs or downloaded from the net is copyrighted (rights of the songwriter,

composer, producer). Copying the data requires permission from the copyright owner how-

ever, permission is not required when the data is used for personal use. If the data is be-

ing copied for distribution or uploading on the net, permission must be obtained from the

Caution

●

Playing Music Files

The Control Box can playback music ﬁles in the SD card.

* Multiple music ﬁles can be grouped together into folders according to genre, etc. however, we

will ﬁrst explain how to make/copy ﬁles without creating folders in the SD card.

Insert an SD card with music ﬁles into the card slot on the Control Box.

Press the PLAYER button on the Control Box, to show the player display shown below.

02_SV150S_En_R3.indd 14 14/01/23 13:51

Press the ENTER (

■

) button to start playback. Elapsed playback time and a playback icon (

) are

shown in the upper right of the display. Press ENTER (

■

) button once again to pause (

n n

) playback.

Adjusting Playback Volume

Press the PLAYER button to highlight the Volume ﬁeld, then use the +/– buttons to adjust the volume.

The adjustable range is from 0 to 30. The factory default is 20.

* This setting has no effect on the SILENT Violin™’s volume.

Adjusting Playback Speed

Press the PLAYER button to highlight the Speed ﬁeld, then use the +/– buttons to adjust the playback

speed. The adjustable range is from 75 to 125%. The factory default is 100%.

* With the exception of MIDI ﬁles (.mid), noise may be heard when the playback speed is

changed.

Using the –(

) and +(

) Button Functions

• The –(

) button can be used to rewind and the +(

) button to fast forward playback when the folder

mark (

) or the File Name ﬁeld is highlighted during playback.

• Pressing the –(

) button while playback is paused, moves the playback point to the start of the song

with playback paused. Pressing the –(

) button again selects and displays the previous music ﬁle.

• Pressing the +(

) button while playback is paused, selects the next music ﬁle.

File Name/Subfolder Name

Folder Name

Selecting music ﬁles within folders

If ﬁles are in folders, ﬁrst highlight the File Name ﬁeld, then use the +/– buttons to select the de-

sired folder and press the ENTER button.

Files (and subfolders) inside of the selected folder are displayed in alphabetical order in the File

Name ﬁeld. Use the +/– buttons to select the desired ﬁle (or subfolder).

Highlighting a sub folder in the File Name ﬁeld then pressing the ENTER button displays the

names of ﬁles found in the subfolder.

Press the PLAYER button to highlight the folder mark (

→

) and then press the ENTER

button to move to the parent folder (higher in the folder hierarchy).

Folder Mark

02_SV150S_En_R3.indd 15 14/01/23 13:51

■

Messages

Message Contents

Total Volume: n Displays the overall volume (n).

Mute On. The mute function is engaged.

Holding. The hold function is engaged.

Low Battery! Battery power is low. Please change batteries as soon as possible.

Clear Setting! Settings have been cleared.

Format Error! An error was found in ﬁle selected for playback.

File Open Error! An error occurred while opening a ﬁle from the SD card.

File Read Error! An error occurred while reading a ﬁle from the SD card.

●

Compatible Formats

[AAC (.m4a), .mp3, .wav Compatible Formats]

Sampling Frequency 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 (kHz)

Number of Channels 1 (Monaural), 2 (Stereo)

Bit Rate (kbps) 8 to 320 (with AAC (.m4a), .mp3)

Bit Length 8bit, 16bit (with .wav)

[.mid Compatible Formats]

File Type Standard Midi File Format 0, 1

File Size 100KB

Tone Generator Speciﬁcations General Midi Level 1

Number of Channels 16

Maximum Polyphony 32 Notes

• Never remove the SD card during playback or while playback is paused. It can damage the ﬁles or

Control Box.

* The maximum number of subfolders/ﬁles that can be set in a single folder is 100.

* The maximum number of subfolder hierarchies is 5.

* The maximum number of characters for the full path name (from the root folder through all the

tied folders) is 258.

* File names using umlaut, circumﬂex, Asian multi-byte language, etc. are not compatible.

* Compatible with SD memory cards of up to 2GB (not compatible with SDHC cards).

* Please use the special software provided by the card maker when formatting the SD card.

* Not compatible with copyright protection functions such as SD-Audio.

02_SV150S_En_R3.indd 16 14/01/23 13:51

Power Supply

The SILENT Violin™ SV150 can be operated with either battery or AC power.

Power is supplied to the instrument when the POWER button is depressed for approximate-

ly 1 second and batteries are installed or a power adaptor (sold separately) is attached. To

switch the power OFF, hold the POWER button down for more than 2 seconds.

* Settings are saved in memory even when the power is switched off and batteries are installed or

the power adaptor is connected.

■

Using Batteries

Turn the Control Box over and remove the bat-

tery compartment cover.

Insert the two batteries (SUM-3 (AA) size).

Take careful note of the polarity markings as

shown in the illustration above, and insert the

batteries.

Replace the battery compartment cover.

A “Low Battery” message is displayed in the Control Box’s LCD when battery power becomes low. The

low battery icon (

) appears in the upper portion of the display. In this case, replace the batteries as

soon as possible, taking note of the following.

• Always follow the +/– signs when inserting the batteries. Improper insertion may result in ﬁre.

• Always replace worn batteries with a complete set of new batteries. Never mix new and old batteries.

Do not mix different types of batteries (alkaline and manganese, or batteries from different manufactur-

ers, or different types by the same manufacturer). Doing so may result in ﬁre.

• To prevent possible damage to the unit due to battery leakage and unnecessary power drain, remove

the batteries from the unit when it is not going to be used for an extended period of time.

■

Supplying AC Power

AC adaptor is optional, please purchase the optional power adaptor PA-D05K.

Securely connect the power adaptor’s DC connector to the DC IN jack on the side of the Control Box.

Plug the AC adaptor into a convenient wall AC power socket.

• Battery power is automatically disconnected when the AC adaptor is connected.

• When using an AC adaptor, make sure you use only the appointed compatible adaptor. The use of an

incompatible adaptor may result in damage to the instrument or cause ﬁre, etc. Please use with cau-

tion.

Bij dit produkt zijn batterijen geleverd.

Wanneer deze leeg zijn, moet u ze niet

weggooien maar inleveren als KCA.

SUM-3 (AA)

size battery x2

Battery compart-

ment cover

* For customers in the Netherlands

02_SV150S_En_R3.indd 17 14/01/23 13:51

Speciﬁcations

Instrument

Neck

Maple

Body

Spruce

Fingerboard/Tuning Pegs

Ebony

Bridge

Maple (Aubert)

Frame

Synthetic Resin

Tailpiece

Adjuster : 4 pieces (Wittner)

Strings

Ball-end type violin strings (Helicore)

Sensor

Piezo pick-up (underneath the bridge)

Power



Supplied via the Control Box connection

String Length

328 mm (12-15/16”)

Dimensions

589 (L) x 206 (W) x 116 (H) mm

23-3/16” (L) x 8-1/8” (W) x 4-9/16” (H)

Weight (instrument only)

approximately 490 g (1 lbs. 1 oz.)

Control

VOLUME

Control Box

Case

Synthetic Resin

Controls

• Data Enter Buttons (–, ENTER, +)

• Mode Select Buttons (PLAYER, SOUND, TUNER,

METRONOME)

• POWER Button (ON/Hold to switch OFF)

• VOLUME/MUTE Rotary Switch

• HOLD Switch

Connections

• Instrument Jack (Input/Output)

• PHONES Jack (Output)

• LINE OUT Jack (Output)

• SD Card Slot

• Power Adaptor Jack (DC5V 500mA)

Power

SUM-3 (AA) size battery x2 or AC Adaptor

Battery Life (Continuous Use)

Using Manganese batteries : approximately 2 hours

Using Alkaline batteries : approximately 10.5 hours

Dimensions

111 (L) x 66 (W) x 19 (H) mm

(excluding the buttons)

4-3/8” (L) x 2-5/8” (W) x 3/4” (H)

Weight

approximately 85 g (3 oz.)

Accessories

SV150

Cable, SD Card, Stereo earphones, SUM-3 (AA) size Manganese battery

x2, Owner’s Manual (this booklet), “Let’s Enjoy Yamaha SILENT Violin™”

(booklet with practice pieces)

SV150S

Bow (4/4 size), Rosin, Soft Case, Cable, SD Card, Stereo earphones,

SUM-3 (AA) size Manganese battery x2, Owner’s Manual (this booklet),

“Let’s Enjoy Yamaha SILENT Violin™” (booklet with practice pieces)

* Design and speciﬁcations are subject to change without notice.

02_SV150S_En_R3.indd 18 14/01/23 13:51

1312 R3 Printed in Japan

Yamaha SV150S El manual del propietario

Marca: Yamaha

Modelo: SV150S

Tipo: El manual del propietario

Este manual también es adecuado para

SV150

Descargar PDF

informe

En otros idiomas

français: Yamaha SV150S Le manuel du propriétaire
italiano: Yamaha SV150S Manuale del proprietario
English: Yamaha SV150S Owner's manual
Deutsch: Yamaha SV150S Bedienungsanleitung
русский: Yamaha SV150S Инструкция по применению
Nederlands: Yamaha SV150S de handleiding
português: Yamaha SV150S Manual do proprietário
dansk: Yamaha SV150S Brugervejledning
polski: Yamaha SV150S Instrukcja obsługi
čeština: Yamaha SV150S Návod k obsluze
svenska: Yamaha SV150S Bruksanvisning
Türkçe: Yamaha SV150S El kitabı
suomi: Yamaha SV150S Omistajan opas
română: Yamaha SV150S Manualul proprietarului

Yamaha SV150S El manual del propietario

Este manual también es adecuado para

Yamaha SV150S El manual del propietario

En otros idiomas

Documentos relacionados