Conair CS50CHBC Manual de usuario

Categoría
Peinados
Tipo
Manual de usuario
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, basic safety precau-
tions should always be taken, including the
following:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY FROM WATER
DANGER Any appliance is electri-
cally live even when the switch is off.
To reduce the risk of death by electric shock:
1. Always unplug appliance immediately
after using.
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it can
fall or be pulled into a tub or sink.
4. Do not place in, or drop into water or other
liquids.
5. If an appliance falls into water, unplug it
immediately. Do not reach into the water.
WARNING To reduce the risk of burns,
electrocution, fi re, or injury to persons:
1. This appliance should never be left unat-
tended when plugged in.
2. This appliance should not be used by, on,
or near children or individuals with certain
disabilities.
3. Use this appliance only for its intended
use as described in this manual. Do not use
attachments not recommended by the manu-
facturer.
4. Do not use an extension cord to operate
appliance.
5. Never operate this appliance if it has
a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged,
or dropped into water. Return the
appliance to an authorized service center
for examination and repair.
6. Keep the cord away from heated surfaces.
7. Do not pull, twist, or wrap line cord around
appliance, even during storage.
8. Never place the appliance on a soft surface,
such as a bed or couch, where the air openings
may be blocked. Keep the air openings free of
lint, hair and the like.
9. Never use while sleeping.
10. Never drop or insert any object into any
opening or hose.
11. Do not use outdoors or operate where
aerosol (spray) products are being used or where
oxygen is being administered.
12. This fl at iron is hot when in use. Do not let
heated surfaces touch eyes or bare skin.
13. Do not place the heated flat iron
directly on any surface or on the appliance
power cord while it is hot or plugged in.
14. Do not attempt to touch the housing of your
appliance near the straightening plates as it is
hot when in use.
15. Do not touch hot surfaces of the appliance.
Use the handles or knobs.
16. Do not use with a voltage converter.
17. Before plugging in, please read the
information about dual voltage in the OPERATING
INSTRUCTIONS section of this booklet.
2. Start with a hair section that is 2 in. wide and
no more than ½ in. thick. Open the iron and
place a hair section between the two hot plates,
close to the scalp. Trap hair between the plates
by rmly squeezing the handles together. While
maintaining the tension, slowly pull the unit down
along the hair section toward the end of hair. At
the end of hair section, release the pressure on
the handle and allow the hair section to slide
out. Repeat process on additional sections of
hair until you achieve the hairstyle you desire.
It may be necessary to repeat process on certain
areas, depending on the texture of your hair.
Some practice is necessary when learning to use
this at iron. After using it several times, you will
learn the ideal way to straighten and style your
hair easily.
STYLING WITH THE NEW EASY GLIDE
CERAMIC-COATED PLATES
The plates of your new at iron have an easy
glide ceramic-coated surface. Hair glides easily
over the surface of the plates as you’re
straightening. The ceramic-coated surface also
helps smooth down yaways and frizzies. As
you smooth each strand, heat is evenly distributed
so that the style you create has a salon-perfect,
silky smooth, shining nish. Hair slips right off
the plates after it’s straightened, and the ceramic
surface is easy to clean.
The ceramic technology is a pleasure to work
with because it makes styling your hair easier
and the results more professional.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
This at iron is intended for household use. This
unit is designed to operate at 120–240 volts AC.
Use on Alternating Current (50/60 hertz) only.
This appliance has a polarized plug (one blade
is wider than the other). As a safety feature, this
plug will fi t in a polarized outlet only one way.
If the plug does not t fully in the outlet, reverse
the plug. If it still does not t, contact a qualifi ed
electrician. Do not attempt to defeat this safety
feature.
DUAL VOLTAGE
This at iron will automatically adjust to the
proper voltage. Use an adapter plug with correct
confi guration, prior to use in outlet.
STRAIGHTENING BASICS
1. Plug the at iron cord into any household out-
let (120–240V). Slide the ON/OFF switch to ON
position. The iron will heat up very quickly. The
power indicator light will remain on when in
operation. To turn off, slide switch to OFF posi-
tion (light will go off). Never leave your at iron
on and unattended.
WARNING: The flat iron’s ceramic-coated
plates will get very hot within a few seconds
and should not come into contact with the
skin after the flat iron has been turned on.
Hair should be clean and completely dried before
using any fl at iron. For best results, use a light
styling product before blow-drying hair.
GETTING TO KNOW YOUR
FLAT IRON
1 in.
ceramic-coated
plates
Power
indicator light
On/Off switch
Ergonomic
handle
Dual voltage
Swivel cord
MEDIDAS DE
SEGURIDAD
IMPORTANTES
Siempre que use aparatos eléctricos, especial-
mente en la presencia de niños, debe tomar
precauciones básicas de seguridad, entre las
cuales las siguientes:
LEA TODAS
LAS INSTRUCCIONES
ANTES DE USARLO
MANTÉNGALO
ALEJADO DEL AGUA
PELIGRO Cualquier aparato enchu-
fado permanece bajo tensión, aunque esté
apagado. Para reducir el riesgo de muerte o
herida por descarga:
1. Siempre desconecte el aparato inmediata-
mente después de usarlo.
2. No lo use en el baño o la ducha.
3. No coloque ni guarde el aparato donde pueda
caer o ser empujado a una bañera o un lavabo.
4. No coloque el aparato ni lo deje caer al agua
u otro líquido.
5. Si el aparato cayera al agua, desconéctelo
inmediatamente; no toque el agua.
ADVERTENCIA Para reducir el
riesgo de quemaduras, electrocución, incendio
o heridas:
1. Nunca descuide ni abandone el aparato
mientras está conectado.
2. Este aparato no debería ser usado por, sobre
o cerca de niños o personas con alguna discapa-
cidad.
3. Utilice este aparato únicamente con el propósi-
to para el cual fue diseñado y solamente según
las instrucciones. Sólo use accesorios recomen-
dados por el fabricante.
4. No utilice una extensión con este aparato.
5. No utilice este aparato si el cordón o la
clavija estuviesen dañados, después de que
hubiese funcionado mal o que se hubiese
caído o si estuviese dañado; regréselo el
aparato a un centro de servicio autorizado
para su revisión y reparación.
6. Mantenga el cable alejado de superfi cies cali-
entes.
7. No jale, retuerza ni enrolle el cable alred-
edor del aparato, incluso para almacenarlo.
8. Nunca haga funcionar el aparato sobre una
superfi cie blanda, como una cama o un sofá,
donde las entradas de aire se puedan obstruir.
Mantenga las aberturas libres de pelusas, cabel-
los y elementos similares.
9. Nunca utilice este aparato mientras duerme.
10. Nunca deje caer ni inserte ningún objeto en
ninguna de las aberturas del aparato.
11. No lo utilice en exteriores, ni lo haga funcio-
nar donde se estén usando productos en aerosol
(spray) o donde se esté administrando oxígeno.
12. Este aparato se vuelve muy caliente; man-
tenga los ojos y la piel alejados de las superfi cies
calientes.
13. No coloque el aparato sobre ninguna
superficie mientras esté caliente o conecta-
do. Manténgalo alejado del cable eléctrico.
14. El cuerpo del aparato cerca de las placas se
vuelve muy caliente durante el uso; no lo toque.
15. No toque las partes calientes de este apara-
to. Utilice las asas o las perillas.
el aparato. Para apagar el aparato, ponga el
botón de encendido/apagado en la posición OFF.
El indicador luminoso se apagará. Nunca deje
el aparato desatendido después de encenderlo.
ADVERTENCIA: las placas se volverán ex-
tremadamente calientes en segundos. Evite
todo contacto con la piel después de en-
cender el aparato.
El cabello debe estar limpio y seco. Para lograr
resultados óptimos, aplique una loción fi jadora
ligera sobre el cabello antes de peinarlo.
2. Divida el cabello en secciones de 2 pulgadas
(5 cm) de ancho por ½ pulgada (1.5 cm) o menos
de espesor. Abra las placas y coloque una sección
de cabello entre ellas, cerca del cuero cabelludo.
Cierre las placas. Baje el aparato lentamente
hasta las puntas, manteniendo la tensión. Suelte
el cabello tras llegar a las puntas. Repita el
proceso con cada sección de cabello. Según la
textura del cabello, puede que sea necesario
repetir el proceso varias veces en cada sección.
Será necesario experimentar un poco al principio.
Con práctica, encontra la manera perfecta
para alisar su cabello fácil y rápidamente.
REVESTIMIENTO DE CERÁMICA
Las placas de su nueva plancha alisadora están
cubiertas de una capa de cerámica increíblemente
suave. El revestimiento hace que el cabello se
deslice fácilmente entre las placas. El
revestimiento de cerámica también ayuda a
controlar la estática y el frizz. Distribuye el calor
uniformemente, para resultados lisos, sedosos
y brillantes – resultados de salón. Además, las
placas son muy fáciles de limpiar.
Es un placer trabajar con esta nueva tecnología,
pues facilita el peinado y permite lograr resultados
profesionales.
16. No utilice este aparato con un convertidor de
voltaje.
17. Lea la información relativa al doble voltaje
que se encuentra en la sección INSTRUCCIONES
DE OPERACIÓN antes de enchufar el aparato en
la toma de corriente.
GUARDE ESTAS
INSTRUCCIONES
INSTRUCCIONES
DE OPERACIÓN
Para uso doméstico solamente. Este aparato ha
sido diseñado para funcionar con corriente de
120–240V AC. Utilícelo solamente con corri-
ente alterna (50/60 Hz).
El cable de este aparato está dotado de una
clavija polarizada (una pata es más ancha que
otra). Como medida de seguridad, se podrá
enchufar de una sola manera en la toma de
corriente polarizada. Si no entrara en la toma
de corriente, inviértela. Si aún no entrara
completamente, comuníquese con un electricista.
No intente ir en contra de esta función de
seguridad.
DOBLE VOLTAJE
Este aparato es bitensión. Se adaptará automáti-
camente al voltaje adecuado. Puede que sea
necesario emplear un adaptador de enchufes
(no se incluye) para utilizarlo fuera de los Estados
Unidos.
FUNDAMENTOS DEL ALISADO
1. Enchufe el aparato en una toma de corriente
de 120–240V. Encienda el aparato (ON). El
aparato calentará muy rápidamente. La luz de
encendido permanecerá encendida hasta apagarse
FAMILIARÍCESE CON SU
PLANCHA ALISADORA
Placas de
25 mm con
revestimiento
de cerámica
Luz de encendido
Botón de
encendido/apagado
Mango
ergonómico
Doble voltaje
Cable giratorio
cs50chbc_15pa014840_ib_final.indd 1 6/12/15 10:46 AM
USER MAINTENANCE
Your fl at iron is virtually maintenance free. No
lubrication is needed. Keep all vents and openings
clear of dirt and dust. If cleaning becomes
necessary, disconnect the unit from the power
source, allow to cool, and wipe exterior with a
cloth. If any abnormal condition occurs, unplug
the unit, allow it to cool, and return it for repair
to an authorized service representative only. No
repairs should be attempted by the consumer.
CAUTION
NEVER allow the power supply cord to be pulled,
twisted, or severely bent. Never wrap the cord
tightly around the appliance. Damage will occur
at the high ex point of entry into the appliance,
causing it to rupture and short circuit. Inspect
the cord frequently for damage. Stop use
immediately if damage is visible or if unit stops
or operates intermittently.
STORAGE
When not in use, your appliance is easy to store.
Allow appliance to cool, then simply store out
of reach of children in a safe, dry location. Do
not jerk or strain cord at plug connections. Do
not wrap the line cord around the appliance.
Allow the cord to hang or lie loose and straight
at the point of entry into the appliance.
SERVICE CENTER
CONAIR CORPORATION
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
©2015 CONAIR CORPORATION
15PA014840
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU’RE WRONG.
KEEP AWAY FROM WATER
Everyone knows that electricity and water
are a dangerous combination. But did you
know that an electric appliance is still
electrically live even if the switch is off?
If the plug is in, the power is on. So when
you are not using your appliances, keep
them unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
LIMITED ONE-YEAR WARRANTY
Conair will repair or replace (at our option) your
unit free of charge for 12 months from the date
of purchase if the appliance is defective in
workmanship or materials.
To obtain service under this warranty, return the
defective product to the service center listed below,
together with your purchase receipt and $7.50 for
postage and handling. California residents need
only provide proof of purchase and should call
1-800-3-CONAIR for shipping instructions. In
the absence of a purchase receipt, the warranty
period shall be 12 months from the date of
manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED
IN DURATION TO THE 12-MONTH DURATION
OF THIS WRITTEN, LIMITED WARRANTY. Some
states do not allow limitations on how long an
implied warranty lasts, so the above limitations
may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, OR CON-
SEQUENTIAL DAMAGES FOR BREACH OF THIS
OR ANY OTHER WARRANTY, EXPRESS OR
IMPLIED, WHATSOEVER. Some states do not
allow the exclusion or limitation of special,
incidental, or consequential damages, so the
above limitation may not apply to you.
This warranty gives you specific legal rights,
and you may also have other rights, which
vary from state to state.
Instruction & Styling Guide
For your safety and continued enjoyment
of this product, always read the instruction
book carefully before using.
Model CS50CHBC
®
IB-13720
Please register this product at:
www.conair.com/registration
1 in.
CERAMIC
FLAT IRON
Product image may differ slightly from actual product purchased.
F
F
L
A
T
INSTRUCCIONES DE
MANTENIMIENTO
Su aparato requiere poco mantenimiento. No
necesita lubricación. Mantenga todas las aberturas
libres de polvos y pelusas. Cuando sea necesario
limpiarlo, desenchúfelo, permita que se enfríe
y limpie la superfi cie exterior con un paño
humedecido. En caso de mal funcionamiento,
desconecte el aparato, permita que enfríe y
regréselo a un centro de servicio autorizado. No
trate de repararlo.
PRECAUCN
NUNCA jale, retuerza ni doble mucho el cable.
Nunca lo enrolle con fuerza alrededor del aparato.
Esto podría dañar la junta exible que lo conecta
al aparato, produciendo su ruptura o un
cortocircuito. Revise el cable con frecuencia para
asegurarse de que no esté dañado. Deje de usar
el aparato inmediatamente si el cable parece
dañado o si el aparato dejara de funcionar o
funcionara de manera intermitente.
ALMACENAJE
Cuando no lo utiliza, su aparato es fácil de
almacenar. Permita que enfríe y guárdelo en un
lugar seco y seguro, fuera del alcance de los
niños. No tironee ni retuerza el cable al nivel del
enchufe. No enrolle el cable alrededor del aparato.
Permita que el cable cuelgue o que la junta que
lo conecta al aparato esté suelta y recta.
CENTRO DE SERVICIO
CONAIR CORPORATION
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
©2015 CONAIR CORPORATION
15PA014840
ADVERTENCIA:
SI CREE QUE NO HAY
CORRIENTE CUANDO
EL APARATO ESTÁ
APAGADO,
ESTÁ EQUIVOCADO
MANTÉNGALO ALEJADO
DEL AGUA
Todos sabemos que no se debe mezclar la
electricidad y el agua. Pero ¿Sabe usted
que un aparato eléctrico permanece bajo
tensión aunque esté apagado? Si está
conectado, hay corriente. Por lo tanto,
siempre desenchufe los aparatos eléctri-
cos después de usarlos.
SIEMPRE DESENCHUFE
LOS APARATOS PEQUEÑOS
GARANTÍA LIMITADA DE UNO
Conair reparará o remplazará (a su opción) su
aparato sin cargo por un período de 12 meses
a partir de la fecha de compra si presentara
defectos de materiales o fabricación.
Para obtener servicio técnico bajo esta garantía,
regrese su aparato al Centro de Servicio indicado
a continuación, junto con su recibo de compra
y un cheque o giro postal de US$7.50 por gastos
de manejo y envío. Los residentes de California
sólo necesitan dar una prueba de compra y deben
llamar al 1-800-3-CONAIR para recibir
instrucciones de envío. En ausencia del recibo
de compra, el período de garantía será de 12
meses a partir de la fecha de fabricación.
CUALQUIER GARANTÍA, OBLIGACIÓN O
RESPONSABILIDAD IMPLÍCITAS, INCLUYENDO
PERO NO LIMITADAS A LA GARANTÍA
IMPLÍCITA DE COMERCIABILIDAD Y APTITUD
PARA UN PROPÓSITO ESPECÍFICO, ESTARÁN
LIMITADAS POR LOS 12 MESES DE LA
PRESENTE GARANTÍA ESCRITA. Algunos
Estados no permiten limitaciones sobre la duración
de una garantía implícita, de modo que las
limitaciones mencionadas pueden no regir para
usted.
CONAIR NO SERÁ RESPONSABLE, EN NINGÚN
CASO, POR NINGÚN DAÑO ESPECIAL,
INCIDENTAL O CONSECUENTE DEBIDO AL
INCUMPLIMIENTO DE ESTA O CUALQUIER
OTRA GARANTÍA, EXPRESA O IMPLÍCITA.
Algunos Estados no permiten la exclusión o
limitación de daños especiales, incidentales
o consecuentes, de modo que las limitaciones
mencionadas pueden no regir para usted.
Esta garantía le otorga derechos legales
específicos y usted puede tener otros derechos
que varían de un Estado a otro.
Instrucciones
Para su seguridad y para disfrutar
plenamente de este producto,
siempre lea las instrucciones
cuidadosamente antes de usarlo.
Modelo CS50CHBC
IB-13720
Para registrar su producto, visítenos en:
www.conair.com/registration
®
PLANCHA ALISADORA
CEMICA de 25 mm
El producto comprado puede diferir ligeramente del producto ilustrado.
R
Á
M
I
cs50chbc_15pa014840_ib_final.indd 2 6/12/15 10:46 AM
  • Page 1 1
  • Page 2 2

Conair CS50CHBC Manual de usuario

Categoría
Peinados
Tipo
Manual de usuario

En otros idiomas