Samoa UP03B-BBS-PTZ Instructions Manual

Tipo
Instructions Manual

Este manual también es adecuado para

1
R. 09/23 855 879
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
Complementary instructions for UP (UP/UE03 / UP/UE05 / UP/UE10 / UP/UE15) diaphragm pumps (according to EC directive 2014/34/UE)
Manual complementario para bombas de diafragma UP (UP/UE03 / UP/UE05 / UP/UE10 / UP/UE15) conformes con la directiva 2014/34/UE/CE (ATEX)
Manuel complémentaire pour les pompes à membranes UP (UP/UE03 / UP/UE05 / UP/UE10 / UP/UE15) conformes à la directive 2014/34/UE/CE (ATEX)
Ergänzungsanleitung für UP (UP/UE03 / UP/UE05 / UP/UE10 / UP/UE15)-Membranpumpen (nach EG-Richtlinie 2014/34/UE)
Дополнительные инструкции для мембранных насосов UP (UP/UE03 / UP/UE05 / UP/UE10 / UP/UE15) (согласно директиве ЕС 2014/34/UE)
Part No. / Cód. / Réf. /
Art. Nr. / Деталь №:
ATEX MANUAL FOR UP/UE03, UP/UE05, UP/UE10 AND UP/UE15 SERIES DIAPHRAGM PUMP 2
MANUAL ATEX BOMBAS DE MEMBRANA SERIES UP/UE03, UP/UE05, UP/UE10 Y UP/UE15 5
MANUEL POMPES A MEMBRANES ATEX SÉRIES UP/UE03, UP/UE05, UP/UE10 ET UP/UE15 8
ATEX-ANLEITUNG FÜR MEMBRANPUMPEN DER SERIEN UP/UE03, UP/UE05, UP/UE10 UND UP/UE15 11
РУКОВОДСТВО ATEX ДЛЯ МЕМБРАННЫХ НАСОСОВ СЕРИИ UP/UE03, UP/UE05, UP/UE10 N UP/UE15 14
EN
ES
FR
DE
RU
UP03 Non-Metallic ATEX
UE03 Non-Metallic ATEX
UP05 Metallic ATEX
UP05 Non-Metallic ATEX
UE05 Metallic ATEX
UE05 Non-Metallic ATEX
UP10 Metallic ATEX
UP10 Non-Metallic ATEX
UE10 Metallic ATEX
UE10 Non-Metallic ATEX
UP15 Metallic ATEX
UP15 Non-Metallic ATEX
UE15 Metallic ATEX
UE15 Non-Metallic ATEX
2855 879 R. 09/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
EN DESCRIPTION
ATEX MARKING
On the pump that accompanies this manual you should locate a label
like the one shown in the figure below. This label includes the following
information (do not use the pump in an ATEX atmosphere if it does not
have such a label):
Ex: Indicates that it is possible to use this pump in a potentially
explosive atmosphere.
II: Indica el grupo al que corresponde la bomba. El Grupo II indica que este
equipo puede ser utilizado en instalaciones de superficie donde existe riesgo
de formación de una atmósfera explosiva.
2: Indicates the category within the group corresponding to the equipment.
Equipment Category 2 indicates a High Protection Level (Use of equipment
in Zones 1 and 2 for Gas and Zones 21 and 22 for Dust).
Equipment Category 2 within Group II is equipment intended to operate
within the operating parameters set by the manufacturer and ensures a high
level of protection for its intended use in locations where explosive
atmospheres due to mixtures of air with gases, vapours, mists and where
air/dust mixtures are likely to occur. Explosion protection ensures an
adequate level of safety, even in the event of malfunctions or work under
hazardous conditions which normally have to be taken into account.
G: Type of atmosphere Gas. Indicates that the pump can be used in a
potentially explosive atmosphere due to gas, vapour or mist.
D: Type of atmosphere Dust. Indicates that the pump can be used in a
potentially explosive atmosphere due to Dust.
CAREFULLY READ THE INSTRUCTIONS AND WARNINGS BEFORE STARTING TO OPERATE THE EQUIPMENT
!
LOM 22.409N-C X
h: It indicates that the pump has construction safety protection because
it is a non-electrical piece of equipment. No additional protection
mode is applied.
IIB/IIC: Indicates the explosion group of gases that can form the explosive
atmosphere for which this pump is suitable (in these instructions, conditions
necessary for the use of the pump with each explosion group are noted). In
particular, these groups refer to Flammable Gases (Ethylene) and Highly
Flammable Gases (Hydrogen) respectively.
IIIB: Indicates the explosion group of dusts that can form the explosive
atmosphere for which the pump is suitable. In particular this group refers to
combustible airborne particles and non-conductive dust.
T6…T5 (Gas) / T85°C…T100°C (Polvo): Indicates the limitation
imposed by SAMOA Industrial for the use of the pump with Group IIB and
IIC gases and Group IIIB dusts. The maximum surface temperature that the
equipment will reach in normal operation or with foreseeable faults will
always be lower than 85ºC and 100ºC respectively, without posing a risk of
ignition for the groups of gases and dusts indicated. The above indications
must be respected at all times and under no circumstances must the process
temperature limits indicated in this manual be exceeded.
Gb: High Protection Level for Gas Atmosphere. Indicates that the
equipment does not contain any source of effective ignition during normal
operation and foreseeable malfunctions. The zones of application of the
equipment are Zone 1 (location where an explosive gas atmosphere is likely
to occur in normal operation) and Zone 2 (location where an explosive gas
atmosphere is not likely to occur in normal operation and if it does occur it
is likely to occur only infrequently and for short periods of time).
Db: High Protection Level for Dust atmosphere. Indicates that the equipment
does not contain any source of effective ignition during normal operation and
foreseeable malfunctions. The zones of application for the equipment are Zone
21 (location where a combustible dust cloud atmosphere is likely to occur in
the air in normal operation) and Zone 22 (location where a combustible dust
cloud atmosphere is not likely to occur in the air in normal operation and if it
does occur it is likely to occur only infrequently and for short periods of time).
LOM YY.###: Indicates the reference number (name of the issuer of the
certificate and its reference) of the technical documentation that has been
deposited with the notified body (see declaration of conformity).
X: The letter “X” positioned after the certificate reference number indicates
special conditions of safe use which are conveyed by these operating
instructions to the end user.
The pump you have purchased can be used in a potentially explosive
atmosphere (ATEX). The European Directive 2014/34/EU sets out
essential health and safety requirements for the use of equipment and
protective systems in these atmospheres and leaves the technical
expression of the requirements contained therein to the harmonised
European standards. SAMOA Industrial S.A. has followed a procedure
by means of which it demonstrates the conformity of the product to
which this manual accompanies with these requirements. This process
has consisted of the preparation and subsequent deposit of the required
technical documentation in the notified body mentioned in the
declaration of conformity together with an internal control of production.
Equipment intended for use in this type of atmosphere must have
specific marking which is an essential tool for the end user for the
correct location and use of the pump. The contents of the marking on
ATEX compliant UP (UP03/UP05/UP10/UP15) and UE (UE03/UE05/
UE10/UE15) pumps are explained below. Remember never to use a
UP (UP03/UP05/UP10/UP15) or UE (UE03/UE05/UE10/UE15) pump
that is not marked with this label in a potentially explosive atmosphere,
as the design of the UP (UP03/UP05/UP10/UP15) and UE (UE03/UE05/
UE10/UE15) pumps intended for ATEX use has been partially modified
for this purpose.
Please also remember that when pumping certain fluids, a broken
diaphragm would mean that the area where the pump is placed
becomes a potentially explosive atmosphere. Stop the pump
immediately in case of diaphragm rupture.
II 2G Ex h IIB/IIC T6...T5 Gb
II 2D Ex h IIIB T85ºC...T100ºC Db
MAX. AIR / FLUID PRESSURE:
FLUID IN / OUT:
CODE:
MFG. DATE:
MODEL:
SERIAL No.:
www.samoaindustrial.com
MADE IN SPAIN
PATENTED
0163
3
R. 09/23 855 879
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
EN
ZONES OF USE OF ATEX PUMPS
USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES SPECIAL INSTRUCTIONS
The information in this chapter is a complement to the information
provided in the pump manual. This chapter refers only to the special
cautions and procedures that shall be followed when working in a
potentially explosive atmosphere. Read always both manuals before
starting to use the pump.
Always respect the working conditions for the pump mentioned in its
instructions manual.
Pump installation, piping, commissioning, maintenance and repair
must be done by qualified personnel.
Be sure that the pump is used following its marking and in approved zones.
Be sure that the pump is well primed before start pumping flammable
or explosive fluids.
Do not close the suction line and do not adjust pump speed or
operation acting on it.
Check regularly for pump leaks.
To avoid risks from static electricity, always use conductive elements
for the connection of the pump. The use of non-conductive elements
external to the UP (UP03/UP05/UP10/UP15) and UE (UE03/UE05/
UE10/UE15) pumps is the responsibility of the end user.
Additional equipment to the pump must be certified separately.
Never use the pump with non conductive fluids in atmospheres with
IIC gas.
When using the pump equipped with non-conductive diaphragms
that exceed the maximum allowable surface area, as defined in UNE-
EN ISO 80079-36 section 6.7.5 Table 8, the following protection
methods must be applied:
- The equipment is always used to transfer electrically conductive
fluids, or
- The explosive environment is prevented from entering the pump
internals, i.e. dry running is avoided.
Always connect a ground wire, which must be attached to the pump.
It must respect the surface temperature considerations in explosive
atmospheres. UP (UP03/UP05/UP10/UP15) and UE (UE03/UE05/
UE10/UE15) pumps comply with the UNE-EN ISO 80079-36 standard
for their safety, marking the limit temperature for the groups of gases
and vapors for which this pump is intended. The maximum surface
temperature that the equipment will reach in normal operation or
with foreseeable failures will always be lower than 85ºC and 100ºC
respectively, and will depend directly on the temperature of the
pumped fluid. The above indications must be respected at all times
and under no circumstances should the process temperature limits
indicated in this manual be exceeded.
For use in explosive atmospheres formed by dust, bear in mind that
the maximum surface temperature that the equipment will reach in
normal operation or with foreseeable failures will always be lower
than 85ºC and 100ºC respectively, and will depend directly on the
temperature of the pumped fluid. Under no circumstances should the
process temperature limits indicated in this manual be exceeded.
In the presence of explosive atmospheres, maintain the pump away
from such atmospheres. Under no circumstances should the
equipment be dismantled or opened (opening the pump and
disassembling its various components) in the presence of
explosive atmospheres.
Clean the pump regularly and remove all dust accumulation on its
surface when working in a potential explosive atmosphere.
Be sure all elements are well connected before running the pump.
Always use flexible connecting elements and install pump on silent
blocks to avoid vibrations.
Be sure valves at the pump inlet and outlet are open before running
the pump.
Avoid the pump to run dry. Install a detection system like a low level
detector in the fluid storage tank.
Maintain and inspect the pump regularly. Make sure the pump is
serviced according to the service instructions by a qualified repair
station. Use only original SAMOA parts for servicing. Use of non
original parts will make the ATEX approval invalid.
Make sure that pump is placed in a safe location, with no risk of parts
or materials falling on it.
When the pump is not operating normally it should be maintained
properly. It is the responsibility of the end user to respect the
conditions of use of the pump.
The construction of the UP (UP03/UP05/UP10/UP15) and UE (UE03/
UE05/UE10/UE15) pumps ensures that the parts necessary to achieve
the safety level cannot be unintentionally dismantled. Always check
tightening torques and strictly follow the maintenance instructions in
the instruction manual.
WARNING: FOLLOW THE INSTRUCTIONS MENTIONED IN THIS CHAPTER TO AVOID RISKS OF SERIOUS INJURIES OR
DEATH AND DAMAGE OF THE EQUIPMENT AND ITS ENVIRONMENT.
!
Areas defined as G (gas): Valid for zones 1 and 2.
Zone 1: Location where an explosive gas, vapour or mist atmosphere is
likely to occur in normal operation (excluding gas which may be present
in mines, firedamp).
Zone 2: Location where an explosive gas, vapour or mist atmosphere
is likely to occur in normal operation (excluding gas which may be
present in mines, firedamp).
Areas defined as D (dust): Valid for zones 21 and 22.
Zone 21: Location where a combustible dust cloud atmosphere is
likely to occur in the air in normal operation.
Zone 22: Location where a combustible dust cloud atmosphere is
not likely to occur in the air in normal operation and if it does occur
it is likely to occur only infrequently and for short periods of time.
Temperature tables
AMBIENT
TEMPERATURE
RANGE
PROCESS
TEMPERATURE
RANGE
TEMPERATURE
CLASS
MAXIMUM
SURFACE
TEMPERATURE
-20ºC to +40ºC -20ºC to +75ºC T6 +85ºC
-20ºC to +40ºC -20ºC to +90ºC T5 +100ºC
4855 879 R. 09/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
EN
According to EC directive 2014/34/UE
SAMOA Industrial S.A.
Declares that the following products meet all requirements set forth in
EC directives 2006/42/CE and 2014/34/UE.
If the product is modified without our written permission, or if the
safety instructions in this manual are not followed,
this declaration will become invalid.
Notified body:
(1063) Laboratorio Oficial José María de Madariaga (LOM)
C/Eric Kandel, 1 (Tecnogetafe), 28906, Getafe, Madrid (Spain)
Tech. Doc. Ref.: LOM 22.409N-C X
The norms used for conformity of this product with safety and health
requirements applicable are:
UNE-EN ISO 80079-36
UNE-EN ISO 80079-37
IEC 60079-0
IEC 60079-10
UNE-EN 1127-1
UNE-EN ISO 12100
UNE-EN 809:1999+A1
Marking: the marking includes the Ex symbol and the technical
file reference.
Special instructions for safe use are specified in this manual.
55XXXX
55XXXX.XXX
UP03-XXX-XXX
UE03-XXX-XXX-X
UP05-XXX-XXX
UE05-XXX-XXX-X
UP10-XXX-XXX
UE10-XXX-XXX-X
UP15-XXX-XXX
UE15-XXX-XXX-X
Product families (the X letter is used for variable positions):
For SAMOA INDUSTRIAL, S.A.
Pedro E. Prallong Álvarez
Production Director
DECLARATION OF CONFORMITY
ATEX PUMPS NOMENCLATURE
PUMP TYPE AIR MOTOR HOUSINGS WETTED PARTS ACCESSORIES
1
Pump Type
& Size
2
Central Body
& Air Chambers
3
Fluid Ports /
Location
4
Fluid Chambers
& Manifolds
5
Hardware
Bolts
6
Valve Seats 7
Valve Balls 8
Diaphragms Type
& Material
9
Accessories
(UE pumps only)
UP03
UP05
UP10
UP15
Universal Pump
(Bolted)
UE03
UE05
UE10
UE15
Universal
Pump (Bolted)
with electronic
interface
B*= Conductive
Polypropylene
(black)
A = Aluminium
L = Conductive
polypropylene
with Stainless
Steel air
chambers
S = AISI 316
Stainless Steel
F* = 2” ANSI/DIN
Flanged Ports /
Side Ends.
N = 2” / 3” NPTF
Threaded
Ports / Centre
Horizontal
B = 2” / 3” BSP
Threaded
Ports / Centre
horizontal
C = 2” / 3” ANSI/
DIN Flanged
Ports / Centre
Horizontal
B*= Conductive
Polypropylene
(black)
A = Aluminium
F = Ductile Iron
S = Stainless Steel
C = Carbon
Steel
S = Stainless
Steel
P* = Polypropylene
T* = PTFE
(Teflon®)
A = Aluminium
D = AISI 440
Hardened
Stainless Steel
H = Hytrel®
M = Santoprene®
N = Nitrile
(Buna-N)
S = AISI 316
Stainless Steel
H = Hytrel®
M = Santoprene®
N = Nitrile
(Buna-N)
S = AISI 316
Stainless Steel
T = PTFE (Teflon®)
V = FKM (Viton®)
Conventional
A = Santoprene®
C = Hytrel®
G = Nitrile (Buna-N)
V = FKM (Viton®)
Two-piece
Z = PTFE (Teflon®
with Santoprene®
backer)
Overmolded
H = Hytrel®
N = Nitrile (Buna-N)
T = PTFE / EPDM
(Bonded)
B = Diaphragm leak
detectors (ATEX)
E = Stroke sensor
(ATEX)
H = Diaphragm leak
detectors + Stroke
sensor (ATEX)
*Non-metallic pumps only.
UP03-XXX-XXX
UE03-XXX-XXX-X
UP05-XXX-XXX
UE05-XXX-XXX-X
UP10-XXX-XXX
UE10-XXX-XXX-X
UP15-XXX-XXX
UE15-XXX-XXX-X
UX03X / UX05X / UX10X / UX15X XXX XXX X
5
R. 09/23 855 879
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
ES
DESCRIPCIÓN
La bomba que usted ha adquirido puede ser utilizada en una atmósfera
potencialmente explosiva (ATEX). La directiva europea 2014/34/UE
establece unos requisitos esenciales de seguridad y salud para la
utilización de aparatos y sistemas de protección en estas atmósferas y
deja que recaigan en las normas europeas armonizadas la expresión
técnica de los requisitos que en ella se contienen. SAMOA Industrial S.A.
ha seguido un procedimiento mediante el cual demuestra la conformidad
del producto al que acompaña este manual con estos requisitos. Este
proceso ha consistido en la elaboración y posterior depósito de la
documentación técnica requerida en el organismo notificado
mencionado en la declaración de conformidad junto con un control
interno de la producción.
Los aparatos destinados a su uso en este tipo de atmósferas deben presentar
un marcado específico que es herramienta fundamental para el usuario
final de cara al correcto emplazamiento y uso de la bomba. A continuación
se explicará el contenido del marcado que incorporan las bombas UP
(UP03/UP05/UP10/UP15) y UE (UE03/UE05/UE10/UE15) aptas para ATEX.
Recuerde que nunca debe de utilizar una bomba UP (UP03/UP05/UP10/
UP15) y UE (UE03/UE05/UE10/UE15) que no esté marcada con esta
etiqueta en atmósferas potencialmente explosivas, dado que el diseño de
las bombas UP (UP03/UP05/UP10/UP15) y UE (UE03/UE05/UE10/UE15)
destinadas a uso en ATEX ha sido parcialmente modificado para este fin.
Recuerde también que durante el bombeo de ciertos fluidos, la rotura
de un diafragma implicaría que la zona en la que se emplaza la bomba
pase a ser una atmósfera potencialmente explosiva. Detenga
inmediatamente la bomba en caso de rotura del diafragma.
LEA ATENTAMENTE EL MANUAL DE INSTRUCCIONES Y SUS ADVERTENCIAS ANTES DE EMPEZAR A OPERAR CON EL EQUIPO
!
MARCADO ATEX
En la bomba a la que acompaña este manual usted debería localizar una
etiqueta como la que se muestra en la figura adjunta a continuación. Dicha
etiqueta incluye la siguiente información (no haga uso de la bomba en una
atmósfera ATEX si la misma no incorpora dicha etiqueta):
Ex: Indica que es posible la utilización de esta bomba en una atmósfera
potencialmente explosiva.
II: Indica el grupo al que corresponde la bomba. El Grupo II indica que este
equipo puede ser utilizado en instalaciones de superficie donde existe riesgo
de formación de una atmósfera explosiva
2: Indica la categoría dentro del grupo correspondiente al equipo.
Categoría de Equipo 2 indica un Nivel de Alta Protección (Uso de equipo en
Zonas 1 y 2 para Gas y Zonas 21 y 22 para Polvo).
Los equipos de categoría 2 dentro del Grupo II son equipos destinados a
funcionar dentro de los parámetros operativos fijados por el fabricante y
aseguran un nivel de protección alto para su uso previsto en emplazamientos
donde es probable la formación de atmósferas explosivas debidas a mezclas de
aire con gases, vapores, nieblas y en el caso de ser indicado mezclas aire/polvo.
La protección contra explosiones garantiza un nivel de seguridad suficiente,
aún en caso de que se produzcan anomalías de funcionamiento o se trabaje
en condiciones peligrosas que deban tenerse habitualmente en cuenta.
G: Tipo de atmósfera Gas. Indica que la bomba puede ser empleada en una
atmósfera potencialmente explosiva debida a gas, vapor o niebla.
D: Tipo de atmósfera Polvo. Indica que la bomba puede ser empleada en
una atmósfera potencialmente explosiva debida a polvo.
h:
Nos indica que la bomba presenta protección por seguridad de construcción
por ser un equipo no eléctrico. No se aplica ningún modo de protección adicional.
IIB/IIC: Indica el grupo de explosión de gases que pueden formar la
atmósfera explosiva para los cuales es apta esta bomba (en estas
instrucciones, se apuntan condiciones necesarias para la utilización de
la bomba con cada grupo de explosión). En concreto estos grupos se
refieren a Gases Inflamables (Etileno) y a Gases Fácilmente Inflamables
(Hidrógeno) respectivamente.
IIIB: Indica el grupo de explosión de polvos que pueden formar la atmósfera
explosiva para los cuales es apta la bomba. En concreto este grupo se refiere
a partículas en suspensión combustibles y polvo no conductor.
T6…T5 (Gas) / T85°C…T100°C (Polvo): Indica la limitación que
impone SAMOA Industrial para la utilización de la bomba con los gases
de los Grupos IIB y IIC así como con los polvos del Grupo IIIB. La
máxima temperatura superficial que alcanzará el equipo en
funcionamiento normal o con averías previsibles será siempre inferior a
85ºC y 100ºC respectivamente, sin suponer un riesgo de ignición para
los grupos de gases y polvos indicados. Deben respetarse en todo
momento las indicaciones expuestas y bajo ninguna circunstancia
deben sobrepasarse los límites de temperaturas de proceso que se
indican en éste manual.
Gb: Nivel de Protección Alto para atmósfera de Gas. Indica que el
equipo no contiene ninguna fuente de inflamación efectiva durante el
funcionamiento normal y las averías previsibles. Las zonas de aplicación
del equipo son la Zona 1 (emplazamiento en el que es probable que
aparezca una atmósfera de gas explosiva en funcionamiento normal) y
la Zona 2 (emplazamiento en el que no es probable que aparezca una
atmósfera de gas explosiva en funcionamiento normal y si aparece es
probable solo de forma infrecuente y en periodos de corta duración).
Db: Nivel de Protección Alto para atmósfera de Polvo. Indica que el
equipo no contiene ninguna fuente de inflamación efectiva durante el
funcionamiento normal y las averías previsibles. Las zonas de aplicación
del equipo son la Zona 21 (emplazamiento en el que es probable que
aparezca una atmósfera de nube de polvo combustible en el aire en
funcionamiento normal) y la Zona 22 (emplazamiento en el que no es
probable que aparezca una atmósfera de nube de polvo combustible en
el aire en funcionamiento normal y si aparece es probable solo de forma
infrecuente y en periodos de corta duración).
LOM YY.###-#: Indica el número de referencia (nombre de emisor de
certificado y referencia del mismo) de la documentación técnica que se
ha depositado en el organismo notificado (ver la declaración
de conformidad).
X: La letra “X” posicionada tras el número de referencia del certificado
indica que existen condiciones especiales de uso seguro que se
transmiten mediante este manual de instrucciones al usuario final.
LOM 22.409N-C X
II 2G Ex h IIB/IIC T6...T5 Gb
II 2D Ex h IIIB T85ºC...T100ºC Db
MAX. AIR / FLUID PRESSURE:
FLUID IN / OUT:
CODE:
MFG. DATE:
MODEL:
SERIAL No.:
www.samoaindustrial.com
MADE IN SPAIN
PATENTED
0163
6855 879 R. 09/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
ES
Zonas definidas como G (gas): Válido para zonas 1 y 2.
Zona 1: Emplazamiento en el que es probable que aparezca una
atmósfera de gas, vapor o niebla explosiva en funcionamiento normal
(queda excluido el gas que puede encontrarse presente en minas, grisú).
Zona 2: Emplazamiento en el que no es probable que aparezca una
atmósfera de gas, vapor o niebla explosiva en funcionamiento normal
(queda excluido el gas que puede encontrarse presente en minas,
grisú) y si aparece es probable solo de forma infrecuente y en
periodos de corta duración.
Zonas definidas como D (polvo): Válido para zonas 21 y 22.
Zona 21: Emplazamiento en el que es probable que aparezca
una atmósfera de nube de polvo combustible en el aire
en funcionamiento normal.
Zona 22: Emplazamiento en el que no es probable que aparezca una
atmósfera de nube de polvo combustible en el aire en funcionamiento
normal y si aparece es probable solo de forma infrecuente y en
periodos de corta duración.
ZONAS DE USO DE BOMBAS ATEX
La información que se incluye en este apartado es complementaria a
la dada en el manual de instrucciones. En este apartado se informa
de unas consideraciones que deberá tener especialmente en cuenta
en el uso de aparatos en atmósferas potencialmente explosivas. Lea
siempre ambos manuales antes de operar con la bomba.
Respete las condiciones de uso del equipo indicadas en el manual
de instrucciones.
Las labores de instalación, conexión, arranque, mantenimiento y
reparación deberán realizarse por personal cualificado.
Asegúrese de que instala la bomba en la zona adecuada y bajo las
condiciones correspondientes al marcado.
Asegúrese de que la bomba esta cebada antes de bombear fluidos
inflamables o explosivos.
No cierre completamente la válvula de succión o regule la bomba
con ella.
Revise habitualmente para detectar goteos de la bomba.
Para evitar riesgos derivados de la electricidad estática emplee
siempre elementos conductores para la conexión de la bomba.
El uso de elementos no conductores externos a las bombas UP
(UP03/UP05/UP10/UP15) y UE (UE03/UE05/UE10/UE15) es
responsabilidad del usuario final.
El equipamiento adicional a la bomba debe estar
certificado separadamente.
No utilice la bomba con fluidos no conductivos con atmósferas que
contienen gases del grupo IIC.
Cuando vaya a hacer uso de la bomba equipada con membranas no
conductivas que superen la superficie máxima admisible, como se
define en la norma UNE-EN ISO 80079-36 sección 6.7.5 Tabla 8,
deben aplicarse los siguientes métodos de protección:
- Siempre se utiliza el equipo para transferir fluidos eléctricamente
conductores.
- Se evita que el entorno explosivo entre en las partes internas de la
bomba, es decir, se evita el funcionamiento en seco.
Asegúrese de conectar a tierra la bomba.
Debe respetar las consideraciones sobre temperatura superficial en
atmósferas explosivas. En el marcado de productos ATEX la
temperatura que se marca es la temperatura máxima que puede
llegar a alcanzar el equipo.
Las bombas UP (UP03/UP05/UP10/UP15) y UE (UE03/UE05/UE10/
UE15) se acogen a la normativa UNE-EN ISO 80079-36 por su
seguridad, marcando la temperatura límite para los grupos de gases
y vapores para los que se destina esta bomba. La máxima temperatura
superficial que alcanzará el equipo en funcionamiento normal o con
averías previsibles será siempre inferior a 85ºC y 100ºC
respectivamente, y dependerá directamente de la temperatura del
fluido bombeado. Deben respetarse en todo momento las
indicaciones expuestas y bajo ninguna circunstancia deben
sobrepasarse los límites de temperaturas de proceso que se indican
en este manual.
Para el uso en atmósferas explosivas formadas por polvo, tenga en
cuenta que la máxima temperatura superficial que alcanzará el
equipo en funcionamiento normal o con averías previsibles será
siempre inferior a 85ºC y 100ºC respectivamente, y dependerá
directamente de la temperatura del fluido bombeado. Bajo ninguna
circunstancia deben sobrepasarse los límites de temperaturas de
proceso que se indican en éste manual.
En presencia de atmósferas explosivas realice el mantenimiento de la
bomba lejos de las mismas. Nunca bajo ningún concepto se
procederá al desmontaje o apertura del equipo (apertura de la
bomba y desmontaje de sus diferentes componentes) en presencia
de atmósferas explosivas.
Limpie el área de la bomba y los depósitos de polvo regularmente
cuando trabaje en ambientes con una potencial atmósfera explosiva.
Asegúrese de que todos los elementos están bien conectados antes
de operar con la bomba. Para evitar vibraciones use elementos de
conexión flexibles y Silent Blocks para el amarre.
Asegúrese de que las válvulas de entrada y salida estén abiertas en el
momento de funcionamiento de la bomba.
Evite que la bomba funcione en vacío. Instale algún medio de
detección, como sensor de nivel en el depósito del fluido a vehicular.
Este equipo deberá ser mantenido regularmente. Asegúrese de que
se hace de acuerdo al manual de instrucciones y por un técnico
cualificado. Utilice sólo recambios originales de SAMOA, el uso de
piezas no originales hará que se invalide la aprobación en ATEX.
Cuando la bomba no esté operando normalmente deberá ser
mantenida correctamente. Es responsabilidad del usuario final
respetar las condiciones de uso de la bomba.
La construcción de las bombas UP (UP03/UP05/UP10/UP15) y UE
(UE03/UE05/UE10/UE15) asegura que las partes necesarias para
alcanzar el nivel de seguridad no pueden ser desmontadas de forma
no intencionada. Verifique siempre pares de apriete y siga estrictamente
las instrucciones de mantenimiento del manual de instrucciones.
Prevea protecciones a la hora de instalar la bomba para evitar caída
de objetos sobre la bomba.
ADVERTENCIA: SI NO SE SIGUEN LAS INSTRUCCIONES INDICADAS SE PUEDE PRODUCIR UNA SITUACIÓN DE LESIÓN
GRAVE O MUERTE, ASÍ COMO DAÑOS EN EL EQUIPO E INSTALACIONES ADYACENTES.
!
INSTRUCCIONES ESPECIALES PARA EL USO EN ATMÓSFERAS POTENCIALMENTE EXPLOSIVAS
Tabla de temperaturas
RANGO DE
TEMPERATURA
AMBIENTE
RANGO DE
TEMPERATURA
DE PROCESO
CLASE DE
TEMPERATURA
TEMPERATURA
MÁXIMA
SUPERFICIAL
-20ºC a +40ºC -20ºC a +75ºC T6 +85ºC
-20ºC a +40ºC -20ºC a +90ºC T5 +100ºC
7
R. 09/23 855 879
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
ES
Por SAMOA INDUSTRIAL, S.A.
Pedro E. Prallong Álvarez
Director de Producción
Familia de productos (la letra X se usa para las posiciones
variables):
De acuerdo con la directiva 2014/34/UE (ATEX)
SAMOA Industrial S.A.
Declara que:
Los siguientes productos cumplen con las disposiciones aplicables de las
directivas 2006/42/CE y 2014/34/UE.
Si este producto es modificado sin previo permiso o las instrucciones de
seguridad descritas en el manual no se siguen, esta quedaría invalidada.
Organismo notificado:
(0163) Laboratorio Oficial José María de Madariaga (LOM)
C/Eric Kandel, 1 (Tecnogetafe), 28906, Getafe, Madrid (España)
Referencia documentación técnica: LOM 22.409N-C X
A continuación se hace referencia a las normas armonizadas de las que
se han hecho uso para mostrar la conformidad del producto en cuanto
a los requisitos de seguridad y salud que le aplican:
UNE-EN ISO 80079-36
UNE-EN ISO 80079-37
IEC 60079-0
IEC 60079-10
UNE-EN 1127-1
UNE-EN ISO 12100
UNE-EN 809:1999+A1
Marcado: el marcado incluye el símbolo y la referencia al
expediente técnico.
Condiciones especiales para uso seguro especificadas en el manual de
instrucciones ATEX.
55XXXX
55XXXX.XXX
UP03-XXX-XXX
UE03-XXX-XXX-X
UP05-XXX-XXX
UE05-XXX-XXX-X
UP10-XXX-XXX
UE10-XXX-XXX-X
UP15-XXX-XXX
UE15-XXX-XXX-X
DECLARACIÓN DE CONFORMIDAD CE
CODIFICACIÓN BOMBAS ATEX
TIPO DE
BOMBA MOTOR
NEUMÁTICO ESTRUCTURA EXTERNA CIRCUITO DEL FLUIDO ACCESORIOS
1
Tipo y talla de
la bomba
2
Cuerpo Central
y Cámaras Aire
3
Conexiones
Fluido / Posición
4
Cámaras Fluido
y Colectores
5
Tornillería
de apriete
6
Asientos
Válvulas
7
Bolas 8
Tipo y Material
Membranas
9
Accesorios
(sólo bombas UE)
UP03
UP05
UP10
UP15
Bomba Universal
(atornillada)
UP03
UP05
UP10
UP15
Bomba Universal
(atornillada)
conectada
electrónicamente
B*= Polipropileno
Conductivo
(negro)
A = Aluminio
L = Polipropileno
Conductivo con
las cámaras
en Acero
Inoxidable
S = Acero
Inoxidable
AISI 316
F* = 2” ANSI/DIN
Conex.
embridadas /
Conex. lateral
N = 2” / 3” NPTF
Conex.Roscadas
/ Pos. Central-
Horizontal
B = 2” / 3” BSP
Threaded
Ports / Centre
horizontal
C = 2” / 3” ANSI/
DIN Conex.
embridadas/
Pos. Central-
Horizontal
B*= Polipropileno
Conductivo
(negro)
A = Aluminio
F = Hierro fundido
S = Acero inoxidable
C = Acero al
carbono
S = Acero
inoxidable
P* = Polipropileno
T* = PTFE
(Teflon®)
A = Aluminio
D = Acero Inox.
endurecido
AISI 440
H = Hytrel®
M = Santoprene®
N = Nitrile
(Buna-N)
S = Acero Inox.
AISI 316
H = Hytrel®
M = Santoprene®
N = Nitrile
(Buna-N)
S = Acero Inox.
AISI 316
T = PTFE (Teflon®)
V = FKM (Viton®)
Convencional
A = Santoprene®
C = Hytrel®
G = Nitrile (Buna-N)
V = FKM (Viton®)
Dos-piezas
Z = PTFE (Teflon®
con respaldo de
Santoprene®)
Sobremoldeada
H = Hytrel®
N = Nitrile (Buna-N)
T = PTFE / EPDM
(Bonded)
B = Detectores fuga en
membranas (ATEX)
E = Sensor de carrera
(ATEX)
H = =Detectores fuga
en membranas
+ Sensor carrera
(ATEX)
*Sólo bombas no metálicas.
UX03X / UX05X / UX10X / UX15X XXX XXX X
UP03-XXX-XXX
UE03-XXX-XXX-X
UP05-XXX-XXX
UE05-XXX-XXX-X
UP10-XXX-XXX
UE10-XXX-XXX-X
UP15-XXX-XXX
UE15-XXX-XXX-X
8855 879 R. 09/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
FR DESCRIPTION
La pompe que vous avez achetée peut être utilisée dans une atmosphère
potentiellement explosive (ATEX). La directive européenne 2014/34/UE
fixe les exigences essentielles de santé et de sécurité pour l’utilisation
d’appareils et de systèmes de protection dans de telles atmosphères et
laisse l’expression technique des exigences qu’elle contient aux normes
européennes harmonisées. SAMOA Industrial S.A. a suivi une procédure
par laquelle elle démontre la conformité du produit qui accompagne ce
manuel avec ces exigences. Ce processus a consisté en la préparation et
le dépôt ultérieur de la documentation technique requise auprès de
l’organisme notifié visé dans la déclaration de conformité, ainsi qu’en
un contrôle interne de la production.
Les équipements destinés à être utilisés dans ce type d’atmosphère doivent
être munis d’un marquage spécifique qui est un outil essentiel pour
l’utilisateur final pour l’emplacement et l’utilisation corrects de la pompe. Le
contenu du marquage sur les pompes UP (UP03/UP05/UP10/UP15) et UE
(UE03/UE05/UE10/UE15) conformes à l’ATEX est expliqué ci-dessous.
N’oubliez pas de ne jamais utiliser une pompe UP (UP03/UP05/UP10/UP15)
et UE (UE03/UE05/UE10/UE15) qui n’est pas marquée de cette étiquette
dans des atmosphères potentiellement explosives, car la conception des
pompes UP (UP03/UP05/UP10/UP15) et UE (UE03/UE05/UE10/UE15)
destinées à être utilisées en ATEX a été partiellement modifiée à cette fin.
N’oubliez pas non plus que lors du pompage de certains fluides, la rupture
d’un diaphragme transforme la zone où se trouve la pompe en une
atmosphère potentiellement explosive. Arrêtez immédiatement la pompe
en cas de rupture du diaphragme.
LIRE ATTENTIVEMENT LE MANUEL D’INSTRUCTIONS ET LES MISES EN GARDE AVANT DE COMMENCER A UTILISER LE MATERIEL
!
MARQUAGE ATEX
Sur la pompe qui accompagne ce manuel, vous devriez trouver une
étiquette comme celle de la figure ci-dessous. Cette étiquette comprend les
informations suivantes (ne pas utiliser la pompe dans une atmosphère ATEX
si la pompe ne porte pas une telle étiquette):
Ex: Signifie que la pompe peut être utilisée dans une atmosphère
potentiellement explosive.
II: Indique le groupe auquel appartient la pompe. Le groupe II indique que
cet équipement peut être utilisé dans des installations de surface où il existe
un risque de formation d’atmosphère explosive.
2: Indique la catégorie au sein du groupe d’équipements. La catégorie
d’équipement 2 indique un niveau de protection élevé (utilisation de l’équipement
dans les zones 1 et 2 pour les gaz et les zones 21 et 22 pour les poussières).
Les appareils de catégorie 2 du groupe II sont des appareils destinés à
fonctionner dans le cadre des paramètres de fonctionnement définis par le
fabricant et garantissent un niveau de protection élevé pour l’utilisation prévue
dans des lieux où des atmosphères explosives dues à des mélanges d’air avec
des gaz, des vapeurs, des brouillards et, si indiqué, des mélanges air/poussière
sont susceptibles de se produire. La protection contre les explosions garantit un
niveau de sécurité suffisant, même en cas de dysfonctionnement ou de travail
dans des conditions dangereuses dont il faut tenir compte.
G: Atmosphère type Gaz. Indique que la pompe peut être utilisée dans une
atmosphère potentiellement explosive en raison de la présence de gaz, de
vapeur ou de brouillard.
D: Type d’atmosphère Poussière. Indique que la pompe peut être utilisée
dans une atmosphère potentiellement explosive en raison de la présence
de poussière.
h:
Il nous indique que la pompe dispose d’une protection de sécurité
constructive car il s’agit d’un équipement non électrique. Aucun mode
de protection supplémentaire n’est appliqué.
IIB/IIC: Indique le groupe d’explosion des gaz qui peuvent former
l’atmosphère explosive pour laquelle cette pompe est adaptée (dans ces
instructions, les conditions nécessaires à l’utilisation de la pompe avec
chaque groupe d’explosion sont notées). En particulier, ces groupes se
réfèrent respectivement aux gaz inflammables (éthylène) et aux gaz
inflammables (hydrogène).
IIIB: Indique le groupe d’explosion des poussières qui peuvent former
l’atmosphère explosive pour laquelle la pompe est adaptée. Ce groupe
comprend notamment les particules combustibles en suspension dans
l’air et les poussières non conductrices.
T6…T5 (Gas) / T85°C…T100°C (Poussière): Indique la limitation
imposée par SAMOA Industrial pour l’utilisation de la pompe avec des
gaz des groupes IIB et IIC et des poussières du groupe IIIB. La
température maximale de surface que l’équipement atteindra en
fonctionnement normal ou en cas d’anomalies prévisibles sera toujours
inférieure à 85ºC et 100ºC respectivement, sans présenter de risque
d’inflammation pour les groupes de gaz et de poussières indiqués. Les
indications ci-dessus doivent être respectées à tout moment et les
limites de température du processus indiquées dans ce manuel ne
doivent en aucun cas être dépassées.
Gb: Niveau de protection élevé pour l’atmosphère gazeuse. Indique que
l’équipement ne contient aucune source d’inflammation effective en
fonctionnement normal et en cas de dysfonctionnement prévisible. Les zones
d’application de l’équipement sont la zone 1 (emplacement où une atmosphère
explosive gazeuse est susceptible de se produire en fonctionnement normal) et
la zone 2 (emplacement où une atmosphère explosive gazeuse n’est pas
susceptible de se produire en fonctionnement normal et si elle se produit, elle
est susceptible de ne se produire que rarement et pendant de courtes périodes).
Db: Niveau de protection élevé pour l’atmosphère poussiéreuse. Indique que
l’équipement ne contient aucune source d’inflammation effective en
fonctionnement normal et en cas de dysfonctionnement prévisible. Les zones
d’application de l’équipement sont la zone 21 (emplacement où une
atmosphère de nuage de poussière combustible est susceptible de se produire
dans l’air en fonctionnement normal) et la zone 22 (emplacement où une
atmosphère de nuage de poussière combustible n’est pas susceptible de se
produire dans l’air en fonctionnement normal et si elle se produit, elle est
susceptible de ne se produire que rarement et pendant de courtes périodes).
LOM YY.###-#: Indique le numéro de référence (nom de l’émetteur du
certificat et référence du certificat) de la documentation technique qui a
été déposée auprès de l’organisme notifié (voir déclaration de conformité).
X: La lettre “X” placée après le numéro de référence du certificat
indique qu’il existe des conditions particulières pour une utilisation en
toute sécurité qui sont transmises par ces instructions d’utilisation à
l’utilisateur final.
LOM 22.409N-C X
II 2G Ex h IIB/IIC T6...T5 Gb
II 2D Ex h IIIB T85ºC...T100ºC Db
MAX. AIR / FLUID PRESSURE:
FLUID IN / OUT:
CODE:
MFG. DATE:
MODEL:
SERIAL No.:
www.samoaindustrial.com
MADE IN SPAIN
PATENTED
0163
9
R. 09/23 855 879
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
FR
Zones définies comme G (gaz): Valable pour les zones 1 et 2.
Zone 1: ESite dans lequel une atmosphère explosive sous forme de
gaz, de vapeur ou de brouillard est susceptible de se produire en
fonctionnement normal (à l’exclusion du gaz qui peut être présent
dans les mines, le grisou).
Zone 2: Site dans lequel une atmosphère explosive sous forme de
gaz, de vapeur ou de brouillard n’est pas susceptible de se produire
en fonctionnement normal (à l’exclusion du gaz qui peut être présent
dans les mines, le grisou) et si elle se produit, elle n’est susceptible de
se produire que rarement et pendant de courtes périodes.
Zones définies comme D (poussière): Valable pour les zones 21 et 22.
Zone 21: Un site où une atmosphère de nuage de poussière
combustible est susceptible de se produire dans l’air en
fonctionnement normal.
Zone 22: Un site où une atmosphère de nuage de poussière
combustible n’est pas susceptible de se produire dans l’air en
fonctionnement normal et si elle se produit, elle est susceptible de ne
se produire que rarement et pendant de courtes périodes.
DOMAINES D’UTILISATION DES POMPES ATEX
Les informations contenues dans ce chapitre est un complément aux
informations fournies dans le manuel de la pompe. Ce chapitre
répertorie les mises en garde spéciales et les procédures qui doivent
être suivies lors de l’utilisation dans une atmosphère potentiellement
explosive. Toujours lire attentivement les deux manuels avant de
commencer à utiliser la pompe.
Toujours respecter les conditions de travail mentionnées dans le
manuel d’instructions.
L’installation de la pompe, la tuyauterie, la mise en service, l’entretien
et les réparations doivent être effectuées par du personnel qualifié.
Veillez à installer la pompe dans la zone appropriée et dans les
conditions correspondant au marquage.
Assurez-vous que la pompe est amorcée avant de pomper des fluides
inflammables ou explosifs.
Ne fermez pas complètement le robinet d’aspiration et ne régulez pas la
pompe avec celui-ci.Contrôlez régulièrement l’écoulement de la pompe.
Vérifiez régulièrement l’absence de fuites au niveau de la pompe.
Pour éviter les risques d’électricité statique, utilisez toujours des
éléments conducteurs pour le raccordement de la pompe.
L’utilisation d’éléments non conducteurs externes aux pompes
UP (UP03/UP05/UP10/UP15) et UE (UE03/UE05/UE10/UE15) relève de la
responsabilité de l’utilisateur final.
N’utilisez pas la pompe avec des fluides non conducteurs dans des
atmosphères contenant des gaz du groupe IIC.
Lors de l’utilisation de la pompe équipée de membranes non
conductrices qui dépassent la surface maximale autorisée, comme
défini dans la norme UNE-EN ISO 80079-36 section 6.7.5 Tableau 8,
les méthodes de protection suivantes doivent être utilisées:
- L’équipement est toujours utilisé pour transférer des fluides
électriquement conducteurs ou
- L’environnement explosif est empêché de pénétrer dans les internes
de la pompe, c’est-à-dire que le fonctionnement à sec est évité.
Veillez à mettre la pompe à la terre.
Les considérations relatives à la température de surface pour les
atmosphères explosives doivent être respectées. Dans le marquage
des produits ATEX, la température indiquée est la température
maximale que l’équipement peut atteindre.
Les pompes UP (UP03/UP05/UP10/UP15) et UE (UE03/UE05/UE10/
UE15) sont conformes à la norme de sécurité UNE-EN ISO 80079-36,
qui indique la température limite pour les groupes de gaz et de
vapeurs pour lesquels cette pompe est destinée. La température
maximale de surface que l’équipement atteindra en fonctionnement
normal ou en cas de défaillance prévisible sera toujours inférieure à
85ºC et 100ºC respectivement, et dépendra directement de la
température du fluide pompé. Les indications ci-dessus doivent être
respectées à tout moment et les limites de température du processus
indiquées dans ce manuel ne doivent en aucun cas être dépassées.
Pour une utilisation dans des atmosphères explosives poussiéreuses,
veuillez noter que la température maximale de surface que
l’équipement atteindra en fonctionnement normal ou en cas de
défaillance prévisible sera toujours inférieure à 85ºC et 100ºC
respectivement, et dépendra directement de la température du fluide
pompé. En aucun cas, les limites de température du processus
indiquées dans ce manuel ne doivent être dépassées.
En présence d’atmosphères explosives, entretenez la pompe loin de
l’atmosphère explosive. En aucun cas, l’équipement ne doit être
démonté ou ouvert (ouverture de la pompe et démontage de ses
différents composants) en présence d’atmosphères explosives.
Nettoyez régulièrement la zone de la pompe et les dépôts de
poussière lorsque vous travaillez dans des environnements présentant
un risque d’explosion.
Assurez-vous que tous les éléments sont correctement connectés avant
de faire fonctionner la pompe. Pour éviter les vibrations, utilisez des
éléments de connexion flexibles et des Silent Blocks pour le serrage.
Assurez-vous que les vannes d’entrée et de sortie sont ouvertes lorsque
la pompe est en fonctionnement.
Évitez de faire tourner la pompe au ralenti. Installez un moyen de
détection, tel qu’un capteur de niveau dans le réservoir du
fluide à transporter.
Cet équipement doit être entretenu régulièrement. Veillez à ce
qu’elle soit effectuée conformément au manuel d’instructions et par
un technicien qualifié. N’utilisez que des pièces détachées originales
SAMOA, l’utilisation de pièces non originales invalidera
l’agrément ATEX.
Lorsque la pompe ne fonctionne pas normalement, elle doit être
correctement entretenue. Il est de la responsabilité de l’utilisateur
final de respecter les conditions d’utilisation de la pompe.
La construction des pompes UP (UP03/UP05/UP10/UP15) et UE (UE03/
UE05/UE10/UE15) garantit que les pièces nécessaires pour atteindre le
niveau de sécurité ne peuvent pas être démontées par inadvertance.
Vérifiez toujours les couples de serrage et suivez scrupuleusement les
instructions d’entretien figurant dans le mode d’emploi.
Prévoyez des protections lors de l’installation de la pompe pour éviter
que des objets ne tombent sur la pompe.
AVERTISSEMENT: SUIVEZ LES INSTRUCTIONS MENTIONNÉES DANS CE CHAPITRE POUR ÉVITER LES RISQUES DE
BLESSURES GRAVES OU LA MORT ET LES DOMMAGES DE L’ÉQUIPEMENT ET SON ENVIRONNEMENT.
!
CONDITIONS PARTICULIÈRES D’UTILISATION POUR UNE UTILISATION EN TOUTE SÉCURITÉ
Tableau des températures
PLAGE DE
TEMPÉRATURES
AMBIANTES
PLAGE DE
TEMPÉRATURE
DU PROCESSUS
CLASSE DE
TEMPÉRATURE
TEMPÉRATURE
MAXIMALE
DE SURFACE
-20ºC à +40ºC -20ºC à +75ºC T6 +85ºC
-20ºC à +40ºC -20ºC à +90ºC T5 +100ºC
10 855 879 R. 09/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
FR DÉCLARATION CE DE CONFORMITÉ
Pour SAMOA INDUSTRIAL, S.A.
Pedro E. Prallong Álvarez
Directeur de Production
Familles de produits (La lettre X est utilisée pour des
positions variables):
Conformément à la directive 2014/34/UE (ATEX)
SAMOA Industrial S.A.
Déclare que:
Les produits suivants répondent à toutes les exigences énoncées dans
les directives 2006/42/CE et 2014/34/UE.
Si le produit est modifié sans notre autorisation écrite, ou si les
consignes de sécurité de ce manuel ne sont pas respectées, cette
déclaration ne sera plus valable.
Organisme notifié:
(0163) Laboratorio Oficial José María de Madariaga (LOM)
C/Eric Kandel, 1 (Tecnogetafe), 28906, Getafe, Madrid (España)
Réf. documentation technique: LOM 22.409N-C X
Les normes utilisées pour la conformité de ce produit avec les exigences
applicables de sécurité et de santé sont les suivantes:
UNE-EN ISO 80079-36
UNE-EN ISO 80079-37
IEC 60079-0
IEC 60079-10
UNE-EN 1127-1
UNE-EN ISO 12100
UNE-EN 809:1999+A1
Marquage: Le marquage comprend le symbole Ex et la référence du
dossier technique.
Les instructions spéciales pour une utilisation sûre sont spécifiées dans
ce manuel.
55XXXX
55XXXX.XXX
UP03-XXX-XXX
UE03-XXX-XXX-X
UP05-XXX-XXX
UE05-XXX-XXX-X
UP10-XXX-XXX
UE10-XXX-XXX-X
UP15-XXX-XXX
UE15-XXX-XXX-X
NOMENCLATURE DES POMPES ATEX
POMPE
TYPE MOTEUR
PNEUMATIQUE STRUCTURES EXTERNES CIRCUITS DE FLUIDES ACCESSORIES
1
Type & taille
de pompe
2
Corps central et
chambres à air
3
Orifices produit /
Emplacement
4
Chambres et
collecteurs de
fluides
5
Boulons 6
Sièges de valve 7
Boules de
valve
8
Type Diaphragmes
& Material
9
Accessories
(Pompes UE
uniquement)
UP03
UP05
UP10
UP15
Pompe
universelle
(boulonnée)
UP03
UP05
UP10
UP15
Pompe
universelle
(boulonnée)
avec interface
électronique
B*= Polypropylène
conducteur
(noir)
A = Aluminium
L = Polypropylène
conducteur
avec chambres
à air en acier
inoxydable
S = Acier inoxydable
AISI 316
F* = 2” ANSI/DIN
Flanged Ports /
Side Ends.
N = Orifices filetés
2” / 3” NPTF
/ Centre
Horizontal
B = Orifices
filetés 2” / 3”
BSP / Centre
horizontal
C = Orifices
filetés 2” / 3”
BSP / Centre
horizontal
B*= Polypropylène
conducteur (noir)
A = Aluminium
F = Fer ductile
S = Acier inoxydable
C = Acier au
carbone
S = Acier
inoxydable
P* = Polypropylène
T* = PTFE
(Teflon®)
A = Aluminium
D = Acier
inoxydable
trempé
AISI 440
H = Hytrel®
M = Santoprene®
N = Nitrile
(Buna-N)
S = Acier
inoxydable
AISI 316
H = Hytrel®
M = Santoprene®
N = Nitrile
(Buna-N)
S = Acier
inoxydable
AISI 316
T = PTFE (Teflon®)
V = FKM (Viton®)
Conventional
A = Santoprene®
C = Hytrel®
G = Nitrile (Buna-N)
V = FKM (Viton®)
Deux pièces
Z = PTFE
(Teflon® avec
Santoprene® à
l’arrière)
Surmoulé
H = Hytrel®
N = Nitrile (Buna-N)
T = PTFE / EPDM
(Bonded)
B = Détecteurs de fuites
à membrane (ATEX)
E = Capteur de course
(ATEX)
H = Détecteurs de fuites
à membrane +
Capteur de course
(ATEX)
*Pompes non métalliques uniquement.
UX03X / UX05X / UX10X / UX15X XXX XXX X
UP03-XXX-XXX
UE03-XXX-XXX-X
UP05-XXX-XXX
UE05-XXX-XXX-X
UP10-XXX-XXX
UE10-XXX-XXX-X
UP15-XXX-XXX
UE15-XXX-XXX-X
11
R. 09/23 855 879
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
DE
Die von Ihnen erworbene Pumpe kann in einer explosionsgefährdeten
Atmosphäre (ATEX) eingesetzt werden. Die europäische Richtlinie 2014/34/
EU legt grundlegende Gesundheits- und Sicherheitsanforderungen für die
Verwendung von Geräten und Schutzsystemen in diesen Atmosphären fest
und überlässt die technische Ausgestaltung der darin enthaltenen
Anforderungen der harmonisierten europäischen Normen. SAMOA
Industrial S.A. hat ein Verfahren angewandt, mit dem sie die Konformität
des Produkts, dem dieses Handbuch beiliegt, mit diesen Anforderungen
nachweist. Dieser Prozess bestand aus der Erstellung und anschließenden
Hinterlegung der erforderlichen technischen Dokumentation bei der in der
Konformitätserklärung genannten notifizierten Stelle sowie einer internen
Fertigungskontrolle. Geräte, die für den Einsatz in dieser Art von Atmosphäre
vorgesehen sind, müssen mit einer spezifische Kennzeichnung , die für
den Endanwender ein wesentliches Hilfsmittel für den richtigen Standort
und Betrieb der Pumpe ist. Der Inhalt der Kennzeichnung auf ATEX-
konformen UP (UP03/UP05/UP10/UP15) und UE (UE03/UE05/UE10/
UE15)-Pumpen wird im Folgenden erläutert. Denken Sie daran, niemals
eine UP (UP03/UP05/UP10/UP15) und UE (UE03/UE05/UE10/UE15), die
nicht mit diesem Etikett gekennzeichnet ist, in einem explosionsgefährdeten
Bereich zu verwenden, da die Konstruktion der für den ATEX-Einsatz
vorgesehenen UP (UP03/UP05/UP10/UP15) und UE (UE03/UE05/UE10/
UE15)-Pumpen für diesen Zweck teilweise geändert wurde.
Bitte denken Sie auch daran, dass beim Pumpen bestimmter Flüssigkeiten
ein Membranbruch bedeutet, dass der Bereich, in dem die Pumpe
platziert ist, zu einer explosionsgefährdeten Atmosphäre wird. Die
Pumpe sofort ausschalten im Falle eines Membranbruchs.
LESEN SIE DIE ANWEISUNGEN UND WARNHINWEISE SORGFÄLTIG DURCH, BEVOR SIE DAS GERÄT IN BETRIEB NEHMEN
!
ATEX-KENNZEICHNUNG
Auf der Pumpe, die diesem Handbuch beiliegt, sollten Sie eine
Kennzeichnung wie die in der Abbildung unten gezeigte finden. Diese
Kennzeichnung enthält die folgenden Informationen (verwenden Sie die
Pumpe nicht in einer ATEX-Atmosphäre, wenn sie keine solche
Kennzeichnung hat):
Ex: Bedeutet, dass es möglich ist, diese Pumpe in einer
explosionsgefährdeten Atmosphäre zu verwenden.
II: Gibt die Gruppe an, zu der die Pumpe gehört. Gruppe II bedeutet, dass
dieses Gerät in Oberflächenanlagen verwendet werden kann, in denen die
Gefahr der Bildung einer explosionsfähigen Atmosphäre besteht.
2: Weist auf die Kategorie innerhalb der Gruppe hin, die dem Gerät
entspricht. Die Gerätekategorie 2 kennzeichnet ein hohes Schutzniveau
(Einsatz der Geräte in den Zonen 1 und 2 für Gas und in den Zonen 21 und
22 für Staub).
Die Gerätekategorie 2 innerhalb der Gruppe II sind Geräte, die für den
Betrieb innerhalb der vom Hersteller festgelegten Betriebsparameter
bestimmt sind und ein hohes Maß an Schutz für die bestimmungsgemäße
Verwendung in Bereichen gewährleisten, in denen explosionsfähige
Atmosphären aufgrund von Gemischen von Luft mit Gasen, Dämpfen,
Nebeln und Luft/Staub-Gemischen auftreten können. Der Explosionsschutz
gewährleistet ein ausreichendes Maß an Sicherheit, auch bei Störungen
oder Arbeiten unter gefährlichen Bedingungen, mit denen normalerweise
gerechnet werden muss.
G: Typ des Atmosphärengases. Zeigt an, dass die Pumpe in einer
explosionsgefährdeten Atmosphäre aufgrund von Gas, Dampf oder Nebel
eingesetzt werden kann.
D: Typ des Atmosphärenstaubs. Zeigt an, dass die Pumpe in einer
explosionsgefährdeten Atmosphäre aufgrund von Staub eingesetzt werden kann.
h:
Weist darauf hin, dass die Pumpe über einen Konstruktionssicherheits-
schutz verfügt, da es sich um nicht-elektrische Ausrüstung handelt. Es
wird kein zusätzlicher Schutzmodus angewendet.
IIB/IIC: Weist auf die Explosionsgruppe der Gase hin, die eine
explosionsfähige Atmosphäre bilden können, für die diese Pumpe
geeignet ist (in dieser Anleitung sind die erforderlichen Bedingungen
für den Einsatz der Pumpe für jede Explosionsgruppe vermerkt). Diese
Gruppen beziehen sich insbesondere auf entzündliche Gase (Ethylen)
bzw. hochentzündliche Gase (Wasserstoff).
IIIB: Weist auf die Explosionsgruppe der Stäube hin, die eine
explosionsfähige Atmosphäre bilden können, für die diese Pumpe
geeignet ist. Diese Gruppe bezieht sich insbesondere auf brennbare
Schwebstoffe und nichtleitenden Staub.
T6…T5 (Gas) / T85°C…T100°C (Staub): Gibt die von SAMOA
Industrial auferlegte Beschränkung für die Verwendung der Pumpe mit
Gasen der Gruppe IIB und IIC und Stäuben der Gruppe IIIB an. Die
maximale Oberflächentemperatur, die das Gerät im Normalbetrieb
oder bei vorhersehbaren Störungen erreicht, liegt stets unter 85 ºC bzw.
100 ºC, ohne dass für die angegebenen Gas- und Staubgruppen eine
Entzündungsgefahr besteht. Die oben genannten Angaben müssen
jederzeit beachtet werden, und die in diesem Handbuch angegebenen
Prozesstemperaturgrenzen dürfen unter keinen Umständen
überschritten werden.
Gb: Hohes Schutzniveau für Gasatmosphären. Zeigt an, dass das Gerät
bei normalem Betrieb und vorhersehbaren Fehlfunktionen keine wirksame
Zündquelle enthält. Die Anwendungsbereiche der Geräte sind Zone 1
(Bereich, in dem damit zu rechnen ist, dass bei Normalbetrieb eine
explosionsfähige Gasatmosphäre auftritt) und Zone 2 (Bereich, in dem
damit zu rechnen ist, dass bei Normalbetrieb eine explosionsfähige
Gasatmosphäre nicht oder nur selten und kurzzeitig auftritt).
Db: Hohes Schutzniveau für staubige Atmosphäre. Zeigt an, dass das
Gerät bei normalem Betrieb und vorhersehbaren Fehlfunktionen keine
wirksame Zündquelle enthält. Die Anwendungsbereiche für die Geräte
sind Zone 21 (Orte, an denen bei normalem Betrieb mit dem Auftreten
einer brennbaren Staubwolkenatmosphäre in der Luft zu rechnen ist) und
Zone 22 (Orte, an denen bei normalem Betrieb mit dem Auftreten einer
brennbaren Staubwolkenatmosphäre in der Luft nicht zu rechnen ist, und
wenn doch, dann wahrscheinlich nur selten und für kurze Zeiträume).
LOM YY.###: Referenznummer (Name des Ausstellers des Zertifikats und
dessen Referenz) der technischen Dokumentation, die bei der notifizierten
Stelle hinterlegt wurde (siehe Konformitätserklärung).
X: Referenznummer (Name des Ausstellers des Zertifikats und dessen
Referenz) der technischen Dokumentation, die bei der notifizierten
Stelle hinterlegt wurde (siehe Konformitätserklärung).
BESCHREIBUNG
LOM 22.409N-C X
II 2G Ex h IIB/IIC T6...T5 Gb
II 2D Ex h IIIB T85ºC...T100ºC Db
MAX. AIR / FLUID PRESSURE:
FLUID IN / OUT:
CODE:
MFG. DATE:
MODEL:
SERIAL No.:
www.samoaindustrial.com
MADE IN SPAIN
PATENTED
0163
12 855 879 R. 09/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
DE EINSATZBEREICHE VON ATEX-PUMPEN
Bereiche, die als G (Gas) definiert sind: Gültig für die Zonen 1 und 2.
Zone 1: Ein Bereich, in dem bei Normalbetrieb eine explosionsfähige
Gas-, Dampf- oder Nebelatmosphäre auftreten kann (ausgenommen
Gas, das in Bergwerken oder Gruben vorhanden sein kann).
Zone 2: Ein Bereich, in dem eine explosionsfähige Gas-, Dampf- oder
Nebelatmosphäre bei normalem Betrieb wahrscheinlich nicht auftritt
(ausgenommen Gas, das in Bergwerken oder Gruben vorhanden sein
kann), und wenn sie doch auftritt, dann wahrscheinlich nur selten
und für kurze Zeit.
Bereiche, die als D (Dust - Staub) definiert sind: Gültig für die
Zonen 21 und 22.
Zone 21: Ein Standort, an dem bei normalem Betrieb eine brennbare
Staubwolkenatmosphäre in der Luft auftreten kann.
Zone 22: Ein Standort, an dem eine brennbare Staubwolkenatmosphäre
in der Luft bei normalem Betrieb unwahrscheinlich ist, und wenn sie
doch auftritt, dann wahrscheinlich nur selten und über kurze
Zeiträume hinweg.
Die Informationen in diesem Kapitel sind eine Ergänzung zu den
Informationen in der Betriebsanleitung der Pumpe. Dieses Kapitel
bezieht sich nur auf die besonderen Vorsichtsmaßnahmen und
Verfahren, die bei Arbeiten in einer explosionsgefährdeten Umgebung
zu befolgen sind. Lesen Sie immer beide Betriebsanleitungen, bevor
Sie die Pumpe in Betrieb nehmen.
Beachten Sie immer die in der Betriebsanleitung der Pumpe
angegebenen Arbeitsbedingungen
Installation, Verschlauchung, Inbetriebnahme, Wartung und Reparatur
der Pumpe müssen von qualifiziertem Personal durchgeführt werden.
Stellen Sie sicher, dass die Pumpe entsprechend ihrer Kennzeichnung
und in zugelassenen Zonen verwendet wird.
Stellen Sie sicher, dass die Pumpe gut angesaugt ist, bevor Sie mit dem
Pumpen von entzündlichen oder explosiven Flüssigkeiten beginnen.
Schließen Sie die Saugleitung nicht und verstellen Sie die
Pumpendrehzahl oder den Betrieb dieser nicht.
Prüfen Sie die Pumpe regelmäßig auf Undichtheiten.
Um Risiken durch statische Elektrizität zu vermeiden, verwenden Sie
immer leitfähige Elementefür den Anschluss der Pumpe. Die
Verwendung von nicht leitfähigen Elementen außerhalb der P (UP03/
UP05/UP10/UP15) und UE (UE03/UE05/UE10/UE15) Pumpen liegt in
der Verantwortung des Endanwenders.
Zusatzgeräte zur Pumpe müssen separat zertifiziert werden.
Verwenden Sie die Pumpe niemals mit nicht leitfähigen Flüssigkeiten
in Atmosphären mit IIC-Gas.
Wenn die Pumpe mit nicht leitfähigen Membranen ausgestattet ist,
die die maximal zulässige Oberfläche gemäß UNE-EN ISO 80079-36,
Abschnitt 6.7.5 Tabelle 8, überschreiten, müssen die folgenden
Schutzmaßnahmen angewendet werden:
- Die Geräte werden immer zur Übertragung von elektrisch leitenden
Flüssigkeiten verwendet, oder
- Das Eindringen der explosiven Umgebung in das Innere der Pumpe
wird verhindert, d. h. ein Trockenlauf wird vermieden.
Schließen Sie immer ein Erdungskabel an, das an der Pumpe befestigt
sein muss.
Die Oberflächentemperaturen in explosionsgefährdeten Bereichen
ssen beachtet werden. Die UP (UP03/UP05/UP10/UP15) und UE
(UE03/UE05/UE10/UE15) Pumpen entsprechen der Sicherheitsnorm
UNE-EN ISO 80079-36, die die Grenztemperaturen für die Gas- und
Dampfgruppen angibt, für die diese Pumpe bestimmt ist. Die
maximale Oberflächentemperatur, die das Gerät im Normalbetrieb
oder bei vorhersehbaren Störungen erreicht, liegt immer unter 85 ºC
bzw. 100 ºC und hängt direkt von der Temperatur der gepumpten
Flüssigkeit ab. Die oben genannten Angaben müssen jederzeit
beachtet werden, und die in diesem Handbuch angegebenen
Grenzwerte für die Prozesstemperatur dürfen unter keinen Umständen
überschritten werden.
Beim Einsatz in staubexplosionsgefährdeten Bereichen ist zu
beachten, dass die maximale Oberflächentemperatur, die das Gerät
im Normalbetrieb oder bei vorhersehbaren Störungen erreicht,
immer unter 85ºC bzw. 100ºC liegt und direkt von der Temperatur
des Fördermediums abhängt. Die in diesem Handbuch angegebenen
Grenzwerte für die Prozesstemperatur dürfen unter keinen Umständen
überschritten werden.
Halten Sie die Pumpe bei Vorhandensein explosiver Atmosphären von
diesen fern. Unter keinen Umständen darf das Gerät in Gegenwart
explosiver Atmosphären auseinander genommen oder geöffnet
werden (Öffnen der Pumpe und auseinandernehmen der
verschiedenen Einzelteile).
Reinigen Sie die Pumpe regelmäßig und entfernen Sie alle
Staubansammlungen auf ihrer Oberfläche, wenn Sie in einem
explosionsgefährdeten Bereich arbeiten.
Stellen Sie sicher, dass alle Elemente gut angeschlossen sind, bevor
Sie die Pumpe in Betrieb nehmen.Verwenden Sie immer flexible
Verbindungselemente und installieren Sie die Pumpe auf Silentblöcken,
um Vibrationen zu vermeiden.
Vergewissern Sie sich, dass die Ventile am Pumpeneinlass und -auslass
vor der Inbetriebnahme der Pumpe geöffnet sind.
Vermeiden Sie ein Trockenlaufen der Pumpe. Installieren Sie ein
Erkennungssystem wie z. B. einen Niedrigstand-Detektor im
Flüssigkeitsspeichertank.
Führen Sie regelmäßig eine Wartung und Inspektion der Pumpe durch.
Stellen Sie sicher, dass die Pumpe gemäß der Serviceanleitung von
einer qualifizierten Reparaturstelle gewartet wird. Verwenden Sie für
die Wartung nur originale SAMOA-Teile. Die Verwendung von anderen,
nicht originalen Teilen, führt zum Erlöschen der ATEX-Zulassung.
Stellen Sie sicher, dass die Pumpe an einem sicheren Ort aufgestellt
ist, an dem keine Teile oder Materialien auf sie fallen können.
Sollte die Pumpe nicht normal arbeiten, muss sie gewartet werden.
Es liegt in der Verantwortung des Endanwenders die
Betriebsbedingungen der Pumpe zu beachten.
Die Konstruktion der P (UP03/UP05/UP10/UP15) und UE (UE03/UE05/
UE10/UE15) Pumpen stellt sicher, dass die zum Erreichen des
Sicherheitsniveaus notwendigen Teile nicht unbeabsichtigt demontiert
werden können. Überprüfen Sie stets den Anzugsmoment und halten
Sie sich strikt an die Wartungsanweisungen in der Betriebsanleitung.
WARNUNG: BEFOLGEN SIE DIE IN DIESEM KAPITEL GENANNTEN HINWEISE, UM SCHWERE VERLETZUNGEN,
TOD SOWIE SCHÄDEN AM GERÄT UND SEINER UMGEBUNG ZU VERMEIDEN.
!
BESONDERE HINWEISE ZUM BETRIEB IN EXPLOSIONSGEFÄHRDETEN ATMOSPHÄREN
Temperatur-Tabelle
TEMPERATUR-
BEREICH DER
UMGEBUNG
PROZESS-TEM-
PERATURBE-
REICH
TEMPERATUR-
KLASSE
MAXIMALE OBER-
FLÄCHENTEMPE-
RATUR
-20ºC bis +40ºC -20ºC bis +75ºC T6 +85ºC
-20ºC bis +40ºC -20ºC bis +90ºC T5 +100ºC
13
R. 09/23 855 879
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
DE
Produktfamilien (der Buchstabe X wird für variable
Positionen verwendet):
Gemäß der EU-Richtlinie 2014/34/UE
SAMOA Industrial S.A.
Erklärt, dass die folgenden Produkte alle Anforderungen
der Richtlinien 2006/42/CE und 2014/34/UE erfüllen.
Wenn das Produkt ohne unsere schriftliche Genehmigung verändert
wird, oder wenn die Sicherheitshinweise in dieser Betriebsanleitung
nicht beachtet werden, Ist diese Erklärung ungültig.
Organismo notificado:
(0163) Laboratorio Oficial José María de Madariaga (LOM)
C/Eric Kandel, 1 (Tecnogetafe), 28906, Getafe, Madrid (Spanien)
Tech. Dok. Ref.: : LOM 22.409N-C X
Die für die Konformität dieses Produkts mit den geltenden Sicherheits-
und Gesundheitsanforderungen verwendeten Normen sind:
UNE-EN ISO 80079-36
UNE-EN ISO 80079-37
IEC 60079-0
IEC 60079-10
UNE-EN 1127-1
UNE-EN ISO 12100
UNE-EN 809:1999+A1
Kennzeichnung: Die Kennzeichnung beinhaltet das Ex-Symbol und die
technische Dokumentenreferenz.
In dieser Betriebsanleitung werden besondere Hinweise zur sicheren
Verwendung gegeben.
55XXXX
55XXXX.XXX
UP03-XXX-XXX
UE03-XXX-XXX-X
UP05-XXX-XXX
UE05-XXX-XXX-X
UP10-XXX-XXX
UE10-XXX-XXX-X
UP15-XXX-XXX
UE15-XXX-XXX-X
KONFORMITÄTSERKLÄRUNG
Für SAMOA INDUSTRIAL, S.A.
Pedro E. Prallong Álvarez
Produktionsleiter
NOMENKLATUR DER ATEX-PUMPEN
PUMPEN-
TYP LUFTMOTOR AUSSENSTRUKTUREN LUFT-MOTOR ZUBEHÖR
1
Pumpentyp
und -größe
2
Zentraler Aufbau
& Luftkammern
3
Flüssigkeitsan-
schlüsse / Position
4
Kammern für Flüs-
sigkeiten & Verteiler
5
Hardware-
Schrauben
6
Ventilsitze 7
Ventilkugeln 8
Membranen Typ
& Material
9
Zubehör
(nur UE-Pumpen)
UP03
UP05
UP10
UP15
Universalpumpe
(geschraubt)
UP03
UP05
UP10
UP15
Universalpumpe
(geschraubt) mit
elektronischer
Schnittstelle
B*= Leitfähiges
Polypropylen
(schwarz)
A = Aluminium
L = Leitfähiges
Polypropylen
mit Luft aus
Edelstahl
chambers
S = AISI 316
Rostfreier Stahl
F* = 2“ ANSI/DIN-
Flanschanschlüsse
/ Seitenanschlüsse
N = 2“ / 3“ NPTF-Ge-
windeanschlüsse
/ Mitte Horizontal
B = 2“ / 3“ BSP-Ge-
windeanschlüs-
se / Mitte
horizontal
C = 2“ / 3“ ANSI/DIN
Flanschan-
schlüsse / Mitte
horizontal
B*= Leitfähiges
Polypropylen
(schwarz)
A = Aluminium
F = Sphäroguss
S = Rostfreier Stahl
C = Kohlen-
stoffstahl
S = Rostfreier
Stahl
P* = Polypropylene
T* = PTFE
(Teflon®)
A = Aluminium
D = AISI 440
Gehärteter
Rostfreier Stahl
H = Hytrel®
M = Santoprene®
N = Nitrile
(Buna-N)
S = AISI 316
Rostfreier
Stahl
H = Hytrel®
M = Santoprene®
N = Nitrile
(Buna-N)
S = AISI 316
Rostfreier
Stahl
T = PTFE (Teflon®)
V = FKM (Viton®)
Konventionell
A = Santoprene®
C = Hytrel®
G = Nitrile (Buna-N)
V = FKM (Viton®)
Zweiteilig
Z = PTFE (Teflon®
mit Santoprene®-
Unterlage)
Umgeformt
H = Hytrel®
N = Nitrile (Buna-N)
T = PTFE / EPDM
(Verklebt)
B = Membran-
Leckanzeiger
(ATEX)
E = Hubsensor (ATEX)
H = Membran-
Leckanzeiger +
Hubsensor (ATEX)
*Nur nicht-metallische Pumpen.
UX03X / UX05X / UX10X / UX15X XXX XXX X
UP03-XXX-XXX
UE03-XXX-XXX-X
UP05-XXX-XXX
UE05-XXX-XXX-X
UP10-XXX-XXX
UE10-XXX-XXX-X
UP15-XXX-XXX
UE15-XXX-XXX-X
14 855 879 R. 09/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
RU ОПИСАНИЕ
Приобретенный вами насос можно использовать в потенциально
взрывоопасной среде (ATEX). Европейская директива 2014/34/ЕС
устанавливает основные требования по охране труда и технике
безопасности при использовании оборудования и защитных систем в этих
атмосферах и оставляет техническое выражение содержащихся в ней
требований в соответствии с гармонизированными европейскими
стандартами. SAMOA Industrial S.A. следует процедуре, с помощью которой
она демонстрирует соответствие продукта, к которому относится
настоящее руководство, данным требованиям. Этот процесс состоял из
подготовки и последующего хранения необходимой технической
документации в нотифицированном органе, указанном в декларации о
соответствии, вместе с внутренним контролем производства.
Оборудование, предназначенное для использования в такой атмосфере,
должно иметь специальную маркировку, которая является важным
инструментом для конечного пользователя для правильного размещения
и использования насоса. Содержание маркировки на насосах UP (UP03/
UP05/UP10/UP15), соответствующих требованиям ATEX, поясняется ниже.
Помните, что никогда не используйте насос UP (UP03/UP05/UP10/UP15) и
UE (UE03/UE05/UE10/UE15), не отмеченный этой этикеткой, в потенциально
взрывоопасной среде, так как конструкция насосов UP (UP03/UP05/UP10/
UP15) и UE (UE03/UE05/UE10/UE15), предназначенных для использования
во взрывоопасных зонах, была частично изменена для этой цели.
Также помните, что при перекачивании определенных жидкостей
сломанная диафрагма может привести к тому, что место, где
установлен насос, станет потенциально взрывоопасной
атмосферой, в этом случае немедленно остановите насос в
случае разрыва мембраны.
ПЕРЕД НАЧАЛОМ ЭКСПЛУАТАЦИИ ОБОРУДОВАНИЯ ВНИМАТЕЛЬНО ПРОЧИТАЙТЕ ИНСТРУКЦИИ И ПРЕДУПРЕЖДЕНИЯ
!
МАРКИРОВКА ATEX
На поверхности помпы, к которой прилагается данное руководство, вы
должны найти этикетку, подобную той, что показана на приложенном
рисунке ниже. Указанная этикетка содержит следующую информацию (не
используйте насос в атмосфере ATEX, если на ней нет указанной этикетки).
Ex: Указывает, что этот насос можно использовать в потенциально
взрывоопасной атмосфере.
II: Участок, на котором при нормальной эксплуатации маловероятно
возникновение в воздухе облака горючей пыли, а если оно и
возникает, то, скорее всего, нечасто и на короткое время.
2: Указывает категорию внутри группы, соответствующую
оборудованию. Категория оборудования 2 указывает на Высокий
Уровень Защиты (использование оборудования в зонах 1 и 2 для Газа
и в зонах 21 и 22 для Пыли).
Оборудование категории 2 в группе II это оборудование,
предназначенное для работы в пределах рабочих параметров,
установленных изготовителем, и обеспечивающее высокий уровень
защиты при использовании по назначению в местах, где возможно
образование взрывоопасных сред из-за смесей воздуха с газами,
паров, туманов и, если указано, воздушно-пылевыми смесями.
Категория 2 в Группе II это оборудование, предназначенное для
работы в пределах рабочих параметров, установленных производителем,
и обеспечивающее высокий уровень защиты для его использования по
назначению в местах, где взрывоопасные среды из-за смесей воздуха
с газами, парами, туманами и где воздух/пыль возможны смеси.
Взрывозащита обеспечивает достаточный уровень безопасности даже
в случае неисправностей или работы в опасных условиях, которые
обычно необходимо учитывать..
G: Тип атмосферы Газ. Указывает, что насос можно использовать в
потенциально взрывоопасной среде из-за газа, пара или тумана.
D: Тип атмосферы Пыль. Указывает, что насос можно использовать
в потенциально взрывоопасной атмосфере из-за наличия пыли.
h:
Указывает на то, что насос имеет защиту конструкции, так как
это неэлектрическое оборудование. Дополнительный режим
защиты не применяется.
IIB/IIC: Указывает группу взрывоопасности газов, которые могут
образовывать взрывоопасную среду, для которой подходит данный
насос данной инструкции отмечены условия, необходимые для
использования насоса с каждой группой взрывоопасности). В
частности, эти группы относятся к горючим газам (этилен) и легко
воспламеняющимся газам (водород) соответственно.
IIIB: Указывает группу взрывоопасной пыли, которая может
образовывать взрывоопасную атмосферу, для которой подходит
насос. В частности, к этой группе относятся горючие частицы
воздуха и непроводящая пыль.
T6…T5 (Газ) / T85°C…T100°C (Пыль): Указывает на ограничение,
налагаемое компанией SAMOA Industrial на использование насоса с
газами групп IIB и IIC и пылью группы IIIB. Максимальная температура
поверхности, которой достигнет оборудование при нормальной
работе или при предвидимых неисправностях, всегда будет ниже
85ºC и 100ºC соответственно, не создавая риска воспламенения для
указанных групп газов и пыли. Вышеуказанные указания должны
соблюдаться всегда, и ни в коем случае нельзя превышать пределы
температуры процесса, указанные в данном руководстве.
Gb: Высокий уровень защиты для газовой атмосферы. Указывает на то,
что оборудование не содержит источников эффективного воспламенения
при нормальной работе и прогнозируемых неисправностях. Зонами
применения оборудования являются Зона 1 (место, где возможно
возникновение взрывоопасной газовой атмосферы при нормальной
эксплуатации) и Зона 2 (место, где вероятность возникновения
взрывоопасной газовой атмосферы при нормальной эксплуатации
невелика, а если она и возникает, то лишь изредка и на короткое время).
Db: Высокий уровень защиты для атмосферы пыли. Указывает на
то, что оборудование не содержит источников эффективного
воспламенения при нормальной работе и прогнозируемых
неисправностях. Зоны применения оборудования - это зона 21
(место, где при нормальной работе в воздухе может возникнуть
облако горючей пыли) и зона 22 (место, где при нормальной работе
в воздухе не может возникнуть облако горючей пыли, а если и
возникает, то, скорее всего, нечасто и на короткое время).
LOM YY.###-#: Указывает регистрационный номер (наименование
поставщика выдавшего сертификат и его номер) технической
документации, которая была передана на хранение в
нотифицированный орган (см. декларацию о соответствии).
X: Буква «X», расположенная после номера сертификата,
указывает на особые условия безопасного использования,
которые доводятся до сведения конечного пользователя в данной
инструкции по эксплуатации.
LOM 22.409N-C X
II 2G Ex h IIB/IIC T6...T5 Gb
II 2D Ex h IIIB T85ºC...T100ºC Db
MAX. AIR / FLUID PRESSURE:
FLUID IN / OUT:
CODE:
MFG. DATE:
MODEL:
SERIAL No.:
www.samoaindustrial.com
MADE IN SPAIN
PATENTED
0163
15
R. 09/23 855 879
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
RU
ЗОНЫ ПРИМЕНЕНИЯ НАСОСОВ ATEX
Области, обозначенные как G (газ): Действительны для зон 1 и 2.
Зона 1: Участок, на котором при нормальной эксплуатации
возможно образование взрывоопасной газовой, паровой или
туманной атмосферы (исключая газ, который может
присутствовать в шахтах, брандспойтах).
Зона 2: Участок, на котором при нормальной эксплуатации не
может возникнуть атмосфера взрывоопасного газа, пара или
тумана (исключая газ, который может присутствовать в шахтах,
огневых башнях), а если он и возникает, то, скорее всего,
нечасто и в течение короткого периода времени.
Области, обозначенные как D (пыль): Действительны для зон 21 и 22.
Зона 21: Участок, в воздухе которого при нормальной
эксплуатации возможно возникновение облака горючей пыли.
Зона 22: Участок, на котором при нормальной эксплуатации
маловероятно возникновение в воздухе облака горючей пыли,
а если оно и возникает, то, скорее всего, нечасто и на
короткое время.
Информация в этой главе является дополнением к информации,
представленной в руководстве по эксплуатации насоса. В этой
главе содержатся только особые меры предосторожности и
процедуры, которые необходимо соблюдать при работе в
потенциально взрывоопасной атмосфере. Всегда читайте оба
руководства перед тем, как начать использовать насос.
Всегда соблюдайте условия эксплуатации насоса, указанные в
его руководстве по эксплуатации.
Установка насоса, прокладка трубопровода, ввод в
эксплуатацию, техническое обслуживание и ремонт должны
выполняться квалифицированным персоналом.
Убедитесь, что насос используется в соответствии с его
маркировкой и в разрешенных зонах.
Перед началом перекачки легковоспламеняющихся или
взрывоопасных жидкостей убедитесь, что насос хорошо заполнен.
Не перекрывайте всасывающую трубу и не регулируйте
скорость насоса или воздействующую на нее работу.
Регулярно проверяйте насос на наличие утечек.
Во избежание риска, связанного со статическим электричеством,
всегда используйте проводящие элементы для подключения
насоса. Ответственность за использование непроводящих
элементов вне насосов UP (UP03/UP05/UP10/UP15) и UE (UE03/
UE05/UE10/UE15) несет конечный пользователь.
Дополнительное оборудование к насосу сертифицируется отдельно.
Никогда не используйте насос с непроводящими жидкостями в
атмосфере с газом IIC.
При использовании насоса, оснащенного непроводящими
мембранами, площадь поверхности которых превышает
максимально допустимую, как определено в UNE-EN ISO
80079-36, раздел 6.7.5, таблица 8, должны применяться
следующие методы защиты:
- Оборудование всегда должно использоваться для перекачки
электропроводящих жидкостей, или
- Предотвращать попадание взрывоопасной среды во
внутренние органы насоса, т.е. исключена работа всухую.
Убедитесь, что насос заземлен.
Необходимо соблюдать требования по температуре поверхности
для взрывоопасных сред. В маркировке изделий ATEX
обозначенная температура - это максимальная температура,
которую может достичь оборудование.
Насосы UP (UP03/UP05/UP10/UP15) и UE (UE03/UE05/UE10/UE15)
соответствуют стандарту безопасности UNE-EN ISO 80079-36 с
обозначением предельной температуры для групп газов и паров,
для которых предназначен данный насос. Максимальная
температура поверхности, которой достигнет оборудование при
нормальной работе или при прогнозируемых неисправностях,
всегда будет ниже 85ºC и 100ºC соответственно, и будет напрямую
зависеть от температуры перекачиваемой жидкости.
Вышеуказанные указания должны соблюдаться всегда, и ни в
коем случае нельзя превышать пределы температуры процесса,
указанные в данном руководстве.
При использовании во взрывоопасной пылевой атмосфере
следует учитывать, что максимальная температура поверхности,
которой достигает оборудование при нормальной работе или
при предвидимых неисправностях, всегда будет меньше 85ºC и
100ºC соответственно, и будет напрямую зависеть от
температуры перекачиваемой жидкости. Ни при каких
обстоятельствах не превышайте предельные значения
температуры процесса, указанные в данном руководстве.
Никогда, ни при каких обстоятельствах не разбирайте и не
открывайте оборудование (вскрытие насоса и демонтаж его
различных компонентов) во взрывоопасной среде.
При наличии взрывоопасных сред используйте насос вдали от
них. Никогда, ни при каких обстоятельствах не разбирайте и не
открывайте оборудование (открывая насос и разбирая его
различные компоненты) во взрывоопасной среде.
Регулярно очищайте насос и удаляйте все скопления пыли с его
поверхности при работе в потенциально взрывоопасной среде.
Перед запуском насоса убедитесь, что все элементы хорошо
соединены. Всегда используйте гибкие соединительные
элементы и устанавливайте насос на сайлентблоки, чтобы
избежать вибрации.
Убедитесь, что клапаны на входе и выходе насоса открыты,
прежде чем запускать насос.
Не допускайте работу насоса всухую. Установите систему
обнаружения, такую как датчик низкого уровня, в резервуаре
для хранения жидкости.
Регулярно выполняйте техническое обслуживание и осмотр
насоса. Убедитесь, что насос обслуживается в соответствии с
инструкциями по обслуживанию на квалифицированной
ремонтной станции. Используйте для обслуживания только
оригинальные запчасти SAMOA. Использование неоригинальных
деталей приведет к аннулированию разрешения Ex.
Если насос не работает нормально, его необходимо надлежащим
образом поддерживать. Ответственность за соблюдение
условий использования насоса лежит на конечном пользователе.
Конструкция насосов UP (UP03/UP05/UP10/UP15) и UE (UE03/
UE05/UE10/UE15) гарантирует, что детали, необходимые для
достижения уровня безопасности, не могут быть
непреднамеренно разобраны. Всегда проверяйте моменты
затяжки и строго следуйте указаниям по техническому
обслуживанию, приведенным в инструкции по эксплуатации.
Обеспечьте защиту при установке насоса, чтобы предотвратить
падение посторонних предметов на насос.
ВНИМАНИЕ: СЛЕДУЙТЕ ИНСТРУКЦИЯМ, УПОМЯНУТЫМ В ЭТОЙ ГЛАВЕ, ВО ИЗБЕЖАНИЕ РИСКА СЕРЬЕЗНЫХ
ТРАВМ ИЛИ СМЕРТИ И ПОВРЕЖДЕНИЯ ОБОРУДОВАНИЯ И ОКРУЖАЮЩЕЙ СРЕДЫ.
!
ОСОБЫЕ УКАЗАНИЯ ДЛЯ ИСПОЛЬЗОВАНИЯ В ПОТЕНЦИАЛЬНО ВЗРЫВООПАСНОЙ СРЕДЕ
Таблицы температур
ДИАПАЗОН
ТЕМПЕРАТУР
ОКРУЖАЮЩЕЙ
СРЕДЫ
ДИАПАЗОН
ТЕМПЕРАТУР
ПРОЦЕССА
КЛАССИФИКАЦИЯ
ТЕМПЕРАТУР
МАКСИМАЛЬНАЯ
ТЕМПЕРАТУРА
ПОВЕРХНОСТИ
-20ºC à +40ºC -20ºC à +75ºC T6 +85ºC
-20ºC à +40ºC -20ºC à +90ºC T5 +100ºC
16 855 879 R. 09/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
RU
Для SAMOA INDUSTRIAL, S.A.
Pedro E. Prallong Álvarez
Директор по производству
Семейства продуктов (буква X используется для
изменяемых позиций):
В соответствии с директивой ЕС 2014/34/UE
SAMOA Industrial S.A.
Заявляет, что следующие продукты соответствуют всем требованиям,
изложенным в директивах ЕС 2006/42/CE и 2014/34/UE.
Если изделие модифицируется без нашего письменного
разрешения или не соблюдаются инструкции по технике
безопасности, приведенные в данном руководстве, это заявление
становится недействительным.
Уполномоченный орган:
(1063) Laboratorio Oficial José María de Madariaga (LOM) C/Eric
Kandel, 1 (Tecnogetafe), 28906, Getafe, Madrid (Spain)
Tech. Doc. Ref.: LOM 22.409N-C X
Нормы, используемые для соответствия данного продукта
применимым требованиям безопасности и охраны
здоровья, следующие:
UNE-EN ISO 80079-36
UNE-EN ISO 80079-37
IEC 60079-0
IEC 60079-10
UNE-EN 1127-1
UNE-EN ISO 12100
UNE-EN 809:1999+A1
Маркировка: маркировка включает в себя знак Ex и ссылку на
технический файл.
В данном руководстве приведены специальные инструкции по
безопасному использованию.
55XXXX
55XXXX.XXX
UP03-XXX-XXX
UE03-XXX-XXX-X
UP05-XXX-XXX
UE05-XXX-XXX-X
UP10-XXX-XXX
UE10-XXX-XXX-X
UP15-XXX-XXX
UE15-XXX-XXX-X
ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ
НОМЕНКЛАТУРА НАСОСОВ ATEX
ТИП
НАСОСА ПНЕВМО-
МОТОР КОРПУС СМАЧИВАЕМЫЕ ДЕТАЛИ АКСЕССУАРЫ
1
Тип и раз-
мер
насоса
2
Центральная
часть
и воздушные
камеры
3
Соединения
для
жидкости /
расположение
4
Жидкостные
камеры
и патрубки
5
Крепеж-
ные болты
и вставки
6
Седла
клапанов
7
Шары 8
Тип и мате-
риал
диафрагм
9
Аксессуары
(только для
серии UE)
UP03
UP05
UP10
UP15
Универсальный
насос (болты)
UP03
UP05
UP10
UP15
Универсальный
насос (болты)
с электронным
интерфейсом
B*= Проводящий
полипропилен
(чёрный)
A = Алюминий
L = Проводящий
Полипро-
пилен с
воздушными
камерами из
нержавеющей
S = AISI 316
Нержавею-
щая сталь
F* = 2’’ / 3’’ ANSI/
DIN Фланцевые
порты / боко-
вые торцы
N = 2’’ / 3’’ NPTF /
Центральное
горизонталь-
ное
B = 2’’ BSP /
Центральное
горизонталь-
ное
C = 2’’ / 3’’ ANSI/
DIN Фланцы /
Центральное
горизонталь-
ное
B*= Проводящий
полипропилен
(чёрный)
A = Алюминий
F = Высокопроч-
ный чугун
S = AISI 316
Нержавеющая
сталь
C = Углеро-
дистая
сталь
S = Нержа-
веющая
сталь
P* = Полипропи-
лен
T* = PTFE
(Teon®)
A = Алюминий
D = AISI 440
Закаленная
нержавею-
щая сталь
H = Hytrel®
M = Сантопрен®
N = Нитрил
(Buna-N)
S = AISI 316 Не-
ржавеющая
сталь
H = Хайтрел®
M = Сантопрен®
N = Нитрил
(Buna-N)
S = AISI 316 Не-
ржавеющая
сталь
T = ПТФЭ
(Тефлон®)
V = СКФ
(Витон®)
Стандартная
A = Сантопрен®
C = Хайтрел®
G = Нитрил
(Buna-N)
V = СКФ (Viton®)
Двухкомпо-
нентная
Z = ПТФЭ (Теф-
лон® c под-
держкой из
Сантопрен®)
Переформо-
ванная
H = Хайтрел®
N = Нитрил
(Buna-N)
T = ПТФЭ/ЭПДК
(армированная)
B = Датчик протечки
мембран (ATEX)
E = Датчик хода
(АТЕХ)
H = Датчик протечки
мембраны +
Датчик хода
(ATEX)
*Только неметаллические насосы.
UX03X / UX05X / UX10X / UX15X XXX XXX X
UP03-XXX-XXX
UE03-XXX-XXX-X
UP05-XXX-XXX
UE05-XXX-XXX-X
UP10-XXX-XXX
UE10-XXX-XXX-X
UP15-XXX-XXX
UE15-XXX-XXX-X
17
R. 09/23 855 879
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
RU
NOTES / NOTAS / NOTES / HINWEISE / ПРИМЕЧАНИЯ
18 855 879 R. 09/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
NOTES / NOTAS / NOTES / HINWEISE / ПРИМЕЧАНИЯ
19
R. 09/23 855 879
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
NOTES / NOTAS / NOTES / HINWEISE / ПРИМЕЧАНИЯ
20 855 879 R. 09/23
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2023_09_22-10:00
SAMOA INDUSTRIAL, S.A.
Pol. Ind. Porceyo, I-14 - Camino del Fontán, 831
E-33392 GIJÓN (Asturias) ESPAÑA
Tel.: +34 985 381 488 - Fax: + 34 985 147 213
www.samoaindustrial.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Samoa UP03B-BBS-PTZ Instructions Manual

Tipo
Instructions Manual
Este manual también es adecuado para

En otros idiomas