Maytag MFI2269DRE00 User Instructions

Marca: Maytag

Modelo: MFI2269DRE00

Categoría: Neveras

Tipo: User Instructions

Este manual también es adecuado para

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.maytag.com. In Canada, register your

refrigerator at www.maytag.ca.

For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall of the

refrigerator compartment.

Model Number Serial Number

TableofContents/ Indice/ Tabledesmati res

REFRIGERATOR SAFETY ............................... 2

INSTALLATION INSTRUCTIONS ................... 3

Unpack the Refrigerator ................................ 3

Location Requirements ................................. 3

Electrical Requirements ................................ 4

Water Supply Requirements ......................... 4

Connect the Water Supply ............................ 4

Refrigerator Doors and Drawer ..................... 6

Adjust the Doors ........................................... 9

REFRIGERATOR USE ..................................... 9

Opening and Closing Doors .......................... 9

Using the Controls ........................................ 9

Crisper Humidity Control ............................ 11

Ice Maker and Ice Storage Bin ................... 11

Water and Ice Dispenser ............................. 12

Water Filtration System ............................... 12

REFRIGERATOR CARE ................................. 13

Cleaning ...................................................... 13

Changing the Light Bulb ............................. 13

TROUBLESHOOTING .................................... 14

Refrigerator Operation ................................ 14

Temperature and Moisture ......................... 15

Ice and Water .............................................. 15

WATER FILTER CERTIFICATIONS .............. 16

PERFORMANCE DATA SHEETS .................. 17

WARRANTY .................................................... 19

SEGURIDAD DEL REFRIGERADOR ............ 20

INSTRUCCIONES DE INSTALACION .......... 21

Desempaque el refrigerador ....................... 21

Requisitos de ubicaci6n .............................. 22

Requisitos electricos ................................... 22

Requisitos del suministro de agua .............. 22

Conecte el suministro de agua ................... 23

Puertas y caj6n del refrigerador .................. 24

Ajuste las puertas ........................................ 27

USO DE SU REFRIGERADOR ...................... 27

C6mo abrir y cerrar las puertas .................. 27

Uso de los controles ................................... 27

Control de humedad del caj6n

para verduras .............................................. 29

F_brica de hielo y dep6sito de hielo ........... 29

Despachador de agua y hielo ..................... 30

Sistema de filtraci6n de agua ..................... 31

CUlDADO DE SU REFRIGERADOR ............. 31

Limpieza ...................................................... 31

C6mo cambiar el foco ................................. 32

SOLUCION DE PROBLEMAS ....................... 33

Funcionamiento del refrigerador ................. 33

Temperatura y humedad ............................. 34

Hielo y agua ................................................. 34

HOJA DE DATOS DEL RENDIMIENTO ....... 36

GARANTJA ...................................................... 38

SI_CURITI_ DU RI_FRIGI_RATEUR ................ 39

INSTRUCTIONS D'INSTALLATION .............. 40

Deballage du refrigerateur .......................... 40

Exigences d'emplacement ......................... 41

Specifications electriques ........................... 41

Specifications de I'alimentation en eau ...... 41

Raccordement de la canalisation d'eau ..... 42

Portes et tiroir du refrigerateur .................... 43

Ajustement des portes ................................ 46

UTILISATION DU REFRIGERATEUR ........... 46

Ouverture et fermeture des portes ............. 46

Utilisation des commandes ........................ 46

Reglage de I'humidite dans

le bac & legumes ......................................... 48

Machine &glagons et bac d'entreposage .. 48

Distributeur d'eau et de glagons ................. 49

Systeme de filtration de I'eau ..................... 50

ENTRETIEN DU REFRIGERATEUR ............. 50

Nettoyage .................................................... 50

Remplacement de I'ampoule d'eclairage... 51

DEPANNAGE .................................................. 52

Fonctionnement du refrig6rateur ................ 52

Temperature et humidite ............................. 53

Gla(}ons et eau ............................................ 53

FEUlLLES DE DONNEES SUR LA

PERFORMANCE ............................................ 55

GARANTIE ...................................................... 57

W10731562A

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

ProperDisposalofYourOldRefrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household

use only.

To ensure proper ventilation for your refrigerator, allow for a V2"

(1.25 cm) of space on each side and at the top. Allow for a 1"

(2.54 cm) space behind the refrigerator. If your refrigerator has an

ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 33/4'' (9.5 cm) minimum space between the refrigerator and

wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a maximum

of 110°F (43°C). The preferred room temperature range for

optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

Clean Before Using

After you remove all of the packaging materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

1/2" (1.25 cm)

3s/4" (9.5 cm)

L88_'88 _(8C_ _8_t8_S

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control

(Thermostat, Refrigerator or Freezer Control depending on the

model) to OFF, and then disconnect the refrigerator from the

electrical source. When you are finished, reconnect the

refrigerator to the electrical source and turn cooling on or reset the

control (Thermostat, Refrigerator or Freezer Control depending on

the model) to the desired setting. See "Using the Controls" in the

User Instructions, User Guide, or Use & Care Guide.

,, & ; ,

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • V4"Nut driver

• 7/le"and W' Open-end or two • Y4"Drill bit

adjustable wrenches

• Cordless drill

IM PORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3/_e"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

• For models with water filters, the disposable water filter

should be replaced at least every 6 months.

Water Pressure

A cold water supply with water pressure of between 35 and

120 psi (241 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration

System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IMPORTANT:

• Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX

(cross-linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator

are acceptable, and will help avoid off-taste or odor in your ice

or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the

following Whirlpool Part Numbers:

W10505928RP (7 ft [2.14 m] jacketed PEX),

8212547RP (5 ft [1.52 m] PEX), or

W10267701 RP (25 ft [7.62 m] PEX).

Install tubing only in areas where temperatures will remain

above freezing.

If you turn on the refrigerator before the water line is

connected, turn off the ice maker to avoid excessive noise or

damage to the water valve.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Find a 1/2"to 11/4'' (12.7 mm to 31.8 mm) vertical cold water

pipe near the refrigerator.

IM PORTANT:

• Make sure it is a cold water pipe.

Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the rear of the refrigerator to the water

pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"(6.35 mm)

O.D. (outside diameter) copper tubing. Be sure both ends of

copper tubing are cut square.

5. Using a cordless drill, drill a V4"hole in the cold water pipe you

have selected.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4"drilled hole in

the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws slowly

and evenly so the washer makes a watertight seal. Do not

overtighten.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten or

you may crush the copper tubing.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with

the copper tubing. Avoid kinks when coiling the copper

tubing.

2. Remove the plastic cap from water valve inlet port. Place a

compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet

port. Shape tubing slightly so that the tubing feeds straight

into the port to avoid kinks.

Slide the compression nut over the sleeve and screw into the

water valve inlet port.

..........A

t ........ S

.........C

s_,D

A. Plastic water tubing

B. Sleeve

C. Compression nut

D. Copper tubing

Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise

to completely tighten. Do not overtighten.

...... C

.........D

A. "P" clamp

B. Plastic water line

C. Compression nut

D. Copper tubing

Check connection by pulling on copper tubing. Attach copper

tubing to refrigerator cabinet with a "P" clamp. Turn on water

supply to refrigerator and check for leaks. Correct any leaks.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill the ice container.

_,_v__;_:_;_,_ @_**,,, D_ _ @

All graphics referenced in the following instructions are included

later in this section after "Final Steps."

TOOLS NEEDED: _e", 3/8"and 1/4"hex-head socket wrenches; a

3/3#'or 1/8"hex key; #2 Phillips screwdriver; and a flat-blade

screwdriver.

Remove and Replace Handles

Style 1

1. Using a3/32"or 1/8"hex key, loosen the two setscrews located

on the side of each handle. See Style 1 Handle graphics 1

and 2.

2. Pull the handle straight out from the door or drawer. Make

sure you keep the screws for reattaching the handles.

3. To replace the handles, reverse the directions.

Style 2

ToRemove Handles:

1. Grasp the lower part of the handle firmly, slide the handle up

and pull the handle straight out from the door. See Style 2

Handle graphics 1 and 2.

To Replace Handles:

1. Position the handle so that the large holes in the mounting

clips are down and align the holes with the door studs.

2. Rotate the handle so that the mounting clips are flat against

the door and slide the handle down to engage. See Style 2

Handle graphics 1 and 2.

3. Starting with the right-hand side door, remove the parts for the

top hinge as shown in Top Hinge graphic. Lift the refrigerator

door from the bottom hinge pin.

4. Remove top hinge cover from left side refrigerator door.

Disconnect the wiring plug located on top of the hinge by

wedging a flat-blade screwdriver or your fingernail between

the two sections. See Connections graphic.

5. Disconnect the water line by pulling back on the locking collar

while pulling the water line out of the water line connector. See

Connections graphic.

6. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the left-hand side door from the bottom hinge pin.

7. Remove the base grille. Remove the two screws fastening the

base grille to the cabinet, and set the screws aside. Grasp the

grille and pull it toward you.

Remove Doors and Hinges

IMPORTANT: Remove food and any adjustable door or utility

bins from doors.

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

8. Using a 3/8"hex wrench, remove the leveling leg brackets from

the bottom of the cabinet. Keep screws for later use.

Replace Doors and Hinges

Assemble the parts for the top hinge as shown in Top Hinge

graphic. Do not tighten the screws completely.

Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

Align the door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

4. Reconnect the wiring plug on top of the left-hand side

refrigerator door.

5. Reconnect the water line by pulling back the locking collar

ring while firmly pushing the water line into the connector.

6. Check for leaks. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT: Two people may be required to remove and replace

the freezer drawer. Graphics are included later in this section.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to position the two

screws in the bottom of the drawer front into the brackets.

See Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

1. Replace the base grille.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug into a grounded 3 prong outlet.

3. Return all removable parts to doors and drawer and food to

refrigerator and freezer.

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Bottom Hinges

A. Hinge Pin Cover

B, Bottom Hinge

C. Hinge Screws

Connections

A. Wiring Plug

B. Water Line Connection

Style 1 Handle

A. Flat-Head Handle Screws

B. Refrigerator Door Handle

Style 1 Handle

A. Flat-Head Handle Screws

B. Freezer Drawer Handle

i /

i I

Style 2 Handle

A, Loosen 4 Door Bracket Screws,

Ii REFRIGERATORUSE

IM PORTANT:

Your refrigerator has two adjustable, front leveling screws -

one on each side of the refrigerator base. If your refrigerator

seems unsteady or you want the door to close easier, use the

instructions below.

Before moving the refrigerator, raise the leveling screws so the

front rollers are touching the floor.

Remove the two screws fastening the base grille to the

cabinet, and set the screws aside. Grasp the grille and pull it

toward you.

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

2. Raise or lower the cabinet.

Using a 1/4"hex driver, turn the leveling screw on each side to

raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws. It may take several turns of

the leveling screw to adjust the tilt of the refrigerator.

• To raise, turn the leveling screw clockwise.

• To lower, turn the leveling screw counterclockwise.

A. Leveling screw

B. Front roller

Open the door again to make sure that it closes as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning both leveling screws clockwise. It may take several

more turns, and you should turn both screws the same

amount.

4. Replace the base grille.

A. Hinged seal

The control center is located on the front of the ice and water

dispenser.

Temperature Controls

For your convenience, your temperature controls are preset at the

factory. When you first install your refrigerator, make sure the

controls are still set to the recommended set points as shown.

Recommended Setting

freezer refrigerator

ternperatare temperature

IMPORTANT:

• When the power is on, the temperature display shows the set

point temperature of the compartment.

Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool

the compartments any faster.

The recommended settings should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is

firm.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

Adjusting Controls

The REFRIGERATOR control adjusts the refrigerator compartment

temperature. The FREEZER control adjusts the freezer

compartment temperature.

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart as a

guide.

To Adjust Set Point Temperatures:

The first touch of the up or down arrow touch pad displays the

current temperature set point.

• Press the up or down arrow touch pads until the desired

temperature set point is displayed.

NOTE: Except when first turning on the refrigerator, do not

adjust either temperature control more than one setting at a

time. Wait 24 hours between adjustments for the temperature

to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control

1olower

FREEZER too warm/too little ice FREEZER Control

1olower

REFRIGERATOR too cold REFRIGERATOR Control

1ohigher

FREEZER too cold FREEZER Control

1ohigher

Cooling On/Off

IM PORTANT:

• Depending on your model you may have a control center with

an On/Off button (Style 1), or you may have a control center

without an On/Off button (Style 2).

• The On/Off control turns off cooling for both compartments

and turns off the dispenser. It does not disconnect power to

the refrigerator.

Style I - Press and hold the On/Off button for 3 seconds. The red

LED will light up to indicate that cooling is Off. Press On/Off again

to turn cooling back on. The LED will turn off.

refrigerator

cooling off

hold 3 sec

Style 2 - Press the Freezer up arrow touch pad until OFF appears

in the display. Neither compartment will cool. Press the Freezer or

Refrigerator down arrow touch pad to turn cooling back on.

Additional Control Center Features

PowerCold TM Feature

The PowerCold TM feature assists with periods of high refrigerator

use, full grocery loads, or temporarily warm room temperatures.

• Press the POWERCOLD touch pad to set the freezer and

refrigerator to the lowest temperature settings. Press the

POWERCOLD touch pad again to return to the normal

refrigerator set point.

NOTE: The PowerCold TM feature will automatically shut off in

approximately 2 hours. When the PowerCold TM feature is on,

the temperature cannot be adjusted.

PowerCoid

Humidity Control (on some models)

The Humidity Control feature turns on a heater to help reduce

moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator

uses more energy when Humidity Control is on.

• Press HUMIDITY CONTROL to turn on the door heater. Press

HUMIDITY CONTROL again to turn off the heater. The LED

will be illuminated when Humidity Control is on.

humidity

control

press if

moisture appears

Temp Alarm

The Temp Alarm feature provides temperature information in the

event of a power outage.

Power outage: During a power outage, if the temperatures in the

refrigerator and freezer compartments exceed normal operating

temperatures, the highest temperature reached will be displayed.

• Press the TEMP ALARM touch pad until the indicator light is

lit, to turn on this feature. Press and hold TEMP ALARM for

3 seconds until the indicator light goes off to turn off this

feature.

Temperature alarm: An alarm will sound repeatedly if the freezer

or refrigerator compartment temperatures exceed normal

operating temperatures for an hour or more.

The temperature displays will alternately show the current

temperatures and the highest temperatures the compartments

reached.

Press the TEMP ALARM touch pad once to stop the audible

alarm and alternating temperature displays. The Temp Alarm

light will continue to flash until the refrigerator returns to the

set temperature.

lllll, ,v

temp

alarm

Door Alarm

The Door Alarm feature sounds a chime every few seconds when

the refrigerator door has been left open for 5 continuous minutes.

The chime will sound until the door is closed or Door Alarm is

turned off.

• Press the DOOR ALARM touch pad to turn this feature on or

off. The indicator light will be lit when the Door Alarm feature

is on.

door

alarm

Filter Reset

See "Water Filtration System."

order replace

fitter reset

hold 3 sec

User Preferences

The control center allows you to set user preferences, ifdesired.

Temperature Display (F_C)

This preference allows you to change the temperature display.

F - Temperature in degrees Fahrenheit

C - Temperature in degrees Celsius

Alarm (AL)

This preference allows you to turn off the sound of all alarms.

ON - You will hear the alarm sound.

OFF - You will not hear the alarm sound.

Auto Light Level Selection (LL)

This preference allows you to adjust the dispenser light level from

dimmest to brightest (settings 1 through 9).

NOTE: The Auto Light feature on the control center must be

selected to activate this preference.

Sabbath Mode (SAB)

ON - All control center lights, interior lights and alarm tones will be

disabled.

OFF - All control center lights, interior lights and alarm tones will

be enabled.

NOTE: Press and hold the DOOR ALARM touch pad for

3 seconds to restore all lights.

To Access the User Preferences Menu:

1. Press and hold the DOOR ALARM touch pad for 3 seconds.

The preference name will appear in the Freezer display and

the preference status (F/C or ON/OFF) will appear in the

Refrigerator display.

2. Use the Freezer up or down arrow touch pads to scroll

through the preference names. When the desired preference

name is displayed, press the Refrigerator up or down arrow

touch pads to change the preference status.

3. Set your preferences by pressing and holding the DOOR

ALARM touch pad for 3 seconds.

You can control the amount of humidity in the moisture-sealed

crisper. Depending on your model, adjust the control to any

setting between FRUIT and VEGETABLES or LOW and HIGH.

FRUIT/LOW (open) for best storage of fruits and vegetables with

skins.

VEGETABLES/HIGH (closed) for best storage of fresh, leafy

vegetables.

IM PORTANI"."

• Flush the water system before turning on the ice maker. See

"Water and Ice Dispenser."

• The ice maker and storage bin are located in the upper left-

hand side of the refrigerator compartment.

Turning the Ice Maker On/Off

The On/Off switch is located on the ice maker.

To turn on the ice maker, press the switch to the ON position.

To manually turn off the ice maker, press the switch to the OFF

position.

NOTE: Your ice maker has an automatic shutoff. The ice maker

sensors will automatically stop ice production, but the control will

remain in the ON position.

Removing and Replacing Ice Storage Bin

To Remove the Ice Storage Bin:

1. Hold the base of the storage bin and press the release button

on the lower right.

2. Pull the storage bin out until resistance is felt. Lift up the front

of the ice bin and remove.

3. Press the switch to the OFF position

To Replace the Ice Storage Bin:

IMPORTANT: It may be necessary to turn the auger driver, behind

the ice bin, counterclockwise to properly align the ice bin with the

auger driver. The ice storage bin must be locked in place for

proper ice dispensing.

1. Press the switch to the ON position

2. Slide the ice bin into the guide rails located on either side of

the enclosure.

3. Push the ice bin in until resistance is felt. Raise the front

slightly and push the ice bin in until an audible "click" is heard.

lit .....................A

/,///' -

A. ON position

B. Auger driver

Ice Production Rate

Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced. Allow 3 days to completely

fill the ice storage bin.

The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period.

To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Controls." Wait 24 hours

between adjustments.

Remember

The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice bin and dispenser mechanism.

Do not store anything on top of the ice maker or in the ice

storage bin.

IM PORTANI"."

After connecting the refrigerator to a water source or

replacing the water filter, flush the water system. Use a sturdy

container to depress and hold the water dispenser pad for

5 seconds, then release it for 5 seconds. Repeat until water

begins to flow. Once water begins to flow, continue

depressing and releasing the dispenser pad (5 seconds on,

5 seconds off) until a total of 4 gal. (15 L) has been

dispensed. This will flush air from the filter and water

dispensing system, and prepare the water filter for use.

Additional flushing may be required in some households. As

air is cleared from the system, water may spurt out of the

dispenser.

NOTE: After 5 minutes of continuous dispensing, the

dispenser will stop dispensing water to avoid flooding. To

continue dispensing, remove the container and press the

dispensing lever again.

• The dispenser will dispense either water or cubed ice.

• Allow 24 hours for the refrigerator to cool down and chill

water. Dispense enough water every week to maintain a fresh

supply.

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

Dispense Ice and Water

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

Select water or cubed ice by touching the word WATER or ICE

on the control panel. The light above the control indicates your

selection.

ice water

Press a sturdy container against the dispenser lever.

IMPORTANT: You do not need to apply a lot of pressure to the

lever in order to activate the dispenser. Pressing hard will not

make the water or ice dispense faster or in greater quantities.

3. Remove the container to stop dispensing.

Dispenser Light

NOTES:

• The dispenser lights are LEDs which should not need to be

changed.

• When you use the dispenser, the lever will automatically turn

the light on. Ifyou want the light to be on continuously, you

may choose either On or Auto.

auto on

light

Auto: The light sensor monitors the light level in the room. The

dispenser light will illuminate at half-power when the light level is

low. To activate the Auto option, press the LIGHT button. The Auto

indicator light will illuminate.

On: For continuous light, press the LIGHT button a second time.

The On indicator light will illuminate.

Off: To turn the dispenser light off, press the LIGHT button a third

time.

DispenserLock

The dispenser can be locked for easy cleaning or to avoid

unintentional dispensing by small children and pets.

NOTE: The dispenser lock does not shut off power to the product,

to the ice maker, or to the dispenser light. It just deactivates the

dispenser lever.

To Lock and Unlock Dispenser:

• Press and hold the CONTROL LOCK touch pad for 3 seconds

to lock the dispenser. The indicator light will illuminate when

Lock is on.

• Press and hold the CONTROL LOCK touch pad again for

3 seconds to unlock dispenser. The indicator light will turn off.

control

lock

hold 3 sec

The water filter is located in the upper right-hand corner of the

refrigerator compartment.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status Lights

When a water filter has been installed in the refrigerator the water

filter status lights will remind you when it is time to order and

replace your water filter.

• The Order light (yellow) will illuminate when 90% of the volume

of water for which the filter is rated has passed through the

filter OR 5 months have passed since the filter was installed.

The Replace light (red) will illuminate when the rated volume of

water has passed through the filter OR 6 months have passed

since the filter was installed. A new water filter should be

installed immediately when the Replace light is illuminated.

The disposable water filter should be replaced at least every

6 months OR earlier if the flow of water to your water dispenser or

ice maker decreases noticeably.

Reset Water Filter Status

After replacing the water filter, press and hold RESET FILTER or

FILTER RESET (depending on your model) for 3 seconds. The

Order and Replace indicator lights will blink and then go off when

the system is reset. See "Using the Controls."

Replacing the Water Filter

To purchase a replacement water filter, model UKF8001AXX-750

or UKF8001AXX-200, see "Accessories."

IMPORTANT: Air trapped inthe water system may cause water

and filter to eject. Always dispense water for at least 2 minutes

before removing the filter or blue bypass cap.

1. Turn filter counterclockwise to remove.

2. Remove sealing label from replacement filter and insert the

filter end into the filter head.

Turn the filter clockwise until it stops. Snap the filter cover

closed.

Flush the water system. See "Water Dispenser" or "Water and

Ice Dispenser."

NOTE: The dispenser feature may be used without a water filter

installed. Your water will not be filtered. If this option is chosen,

replace the filter with the blue bypass cap.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

• To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel

Cleaner and Polish, Part Number 20000008. To order the

cleaner, call 1-800-901-2042 U.S.A. or 1-800-807-6777

Canada.

IMPORTANT: This cleaner isfor stainless steel parts only!

Do not allow the Stainless Steel Cleaner and Polish to come

into contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild

detergent in warm water. Dry thoroughly with a soft cloth.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

IMPORTANT: The light bulbs in both the refrigerator and freezer

compartments of your new refrigerator use LED technology. If the

lights do not illuminate when the refrigerator and/or freezer door is

opened, call for assistance or service. See "Warranty" for phone

numbers.

Unplug refrigerator or disconnect power.

Remove the light shield, if necessary.

• Top of the refrigerator compartment - Squeeze both sides

of the light shield while pulling downward to remove.

• Beneath ice storage enclosure (on some models) - Press

along upper edge of light shield and roll light shield

forward to remove.

Replace the burned-out LED bulb(s) with a bulb of the same

size, shape and wattage.

• To replace the burned-out LED bulb with an LED bulb,

order Part Number W10565137 (3.6 watts).

NOTE: Some LED replacement bulbs are not

recommended for wet/damp environments. The

refrigerator and freezer compartments are considered to

be wet/damp environments. If using a brand of LED bulb

other than the recommended LED bulb, before

installation, read and follow all instructions on the LED

packaging.

If an incandescent bulb is used to replace an LED bulb,

use only incandescent bulbs for household appliances

with a maximum of 40 watts.

Replace the light shield(s) by inserting the tabs on the shield

into the liner holes and snap into place.

NOTE: To avoid damaging the light shield, do not force the

shield beyond the locking point.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,

refer to the warranty page in this manual and scan the code with your mobile device, or visit www.maytag.com/product_help.

In Canada, visit www.maytag.ca.

In the U.S.A.: In Canada:

Maytag Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Maytag Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

The refrigerator will not operate The refrigerator seems noisy

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below are

listed some normal sounds with explanations.

• Buzzing - heard when the water valve opens to fill the ice

maker

Pulsating - fans/compressor adjusting to optimize

performance

Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator

Sizzling/Gurgling - water dripping on the heater during

defrost cycle

Popping - contraction/expansion of inside walls, especially

during initial cool-down

Water running - may be heard when ice melts during the

defrost cycle and water runs into the drain pan

Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold

Power cord unplugged? Plug into a grounded 3 prong outlet.

Is outlet working? Plug in a lamp to see if the outlet is

working.

Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. Ifthe problem continues,

call an electrician.

Are controls on? Make sure the refrigerator controls are on.

See "Using the Control(s)."

New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back into the

correct position.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

Temperature is too warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Control(s)."

Temperature is too cold in refrigerator

Refrigerator air vent blocked? If the air vent located in the

top, left, rear corner of the refrigerator compartment is

blocked by items placed directly in front of it, the refrigerator

will get too cold. Move items away from the air vent.

Ice storage bin in correct position? See "Ice Maker and Ice

Storage Bin."

Controls set correctly for the surrounding conditions?

Adjust the controls a setting warmer. Check temperature in

24 hours. See "Using the Control(s)."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Ice maker turned on? Make sure ice maker is on. See "Ice

Maker and Ice Storage Bin."

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Refrigerator door closed completely? Close the door firmly.

If it does not close completely, see "The doors will not close

completely."

• Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice volume improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice quality improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

Odor transfer from food? Use airtight, moisture proof

packaging to store food.

Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

Water filter installed on the refrigerator? Gray or dark

discoloration in ice indicates that the water filtration system

needs additional flushing. Flush the water system before using

a new water filter. Replace water filter when indicated. See

"Water Filtration System."

The water and ice dispenser will not operate properly

Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

Kink in the water source line? Straighten the water source

line.

New installation? Flush and fill the water system. See "Water

and Ice Dispensers."

Is the water pressure at least 35 psi (241 kPa)? The water

pressure to the home determines the flow from the dispenser.

See "Water Supply Requirements."

Water filter installed on the refrigerator? Remove filter and

operate dispenser. If water flow increases, the filter may be

clogged or incorrectly installed. Replace filter or reinstall it

correctly.

Water dispenser measured fill feature is not dispensing an

accurate amount of water? Calibrate the water dispenser.

See "Water and Ice Dispensers."

Refrigerator door closed completely? Close the door firmly.

If it does not close completely, see "The doors will not close

completely."

Recently removed the doors? Make sure the water

dispenser wire/tube assembly has been properly reconnected

at the top of the refrigerator door. See "Refrigerator Doors and

Drawer."

Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

Water is leaking from the dispenser system

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough?

Hold the glass under the dispenser 2 to 3 seconds after

releasing the dispenser lever.

New installation? Flush the water system. See "Water and

Ice Dispensers."

Recently changed water filter? Flush the water system. See

"Water and Ice Dispensers."

Water from the dispenser is warm

NOTE: Water from the dispenser is only chilled to 50°F (10°C).

• New installation? Allow 24 hours after installation for the

water supply to cool completely.

Recently dispensed large amount of water? Allow 24 hours

for water supply to cool completely.

Water not been recently dispensed? The first glass of water

may not be cool. Discard the first glass of water.

Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See "Water

Supply Requirements."

WATERFILTERCERTIFICATIONS

State of Calitbrnia

Department of Public Health

WaterTreatmentDevice

CertificateNumber

03- I583

Date Issued: September 16, 2008

Dine Revised: April 22, 2009

Trademark/Model Designation

UKF8001 AXX-750

46 9O06-750

6700_523-750

Manu_cturer: Cuno lnc

Replacement Elements

Stale of Calitbrnia

Department of Public Health

Water TreatmentDevice

CertificateNumber

09- 1979

Date Issued: May 8, 2009

Date Revised: 6/22/2010

Trademark/Model Designatio_ Replacement Elements

UKF8001

_iiii'iiiiiii_

.... 4690o6

Manufacturer:

Turbidity

Organic Contanlinants

Atrazinc

Lindmlc

Benzene

C'al'bo ful'an

p-dichlorobenzene

'roxaphene

Tetrachlometh3 lent

Rated Service Capacity: 750 gaI Rated Service Flow: 078 gpm

Conditions of Certification:

DO not use where water is microbiologically unsafe or with water of unknown quali+y, except that systems certified

lbr cyst reduction may be used on disinlhcted waters that may contain fillerabIe cysts

Cysts

Turbidity

Benzene ;

Carbofuran ( )

Chtorobenzen¢

Endrin

Ethvlbenzene +

1inda_o : :

Rated Service Capacity: 200 gal 0,55/zpm

Do not use where water is mierobJolhgicali_i _safe _r_ji _ _r o_unKm)_ n quality, except that systems

certified for cyst reduction inay be Used oh _inff_eted Wa_ers that may coniain filterable cysts.

PERFORMANCEDATASHEETS

Interior Water Filtration System

Model UKF8001AXX-750 Capacity 750 Gallons (2839 Liters)

(_) System tested and certified by NSF International against NSF/ANSI Standard 42 for the

reduction of Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI

Standard 53 for the reduction of Lead, Mercury, Atrazine, Benzene, p-Dichlorobenzene,

Carbofuran, Toxaphene, Cysts, Turb d ty, Asbestos, Tetrach oroethy ene and L ndane.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 2.00 mg/L 2.0 mg/L _+10% 0.06 mg/L 0.050625 mg/L 97.00% 97.52%

Particulate Class I* 85% reduction 14,000,000 #/mL At least 370,000 #/mL** 196,666 #/mL 97.40% 99.00%

10,000 particles/mL

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction

Lead: @ pH 6.5 0.010 mg/L 0.150 mg/U 0.15 mg/L _+10% < 0.001 mg/L < 0.001 mg/L >99.30% >99.30%

Lead: @ pH 8.5 0.010 mg/L 0.150 mg/U 0.15 mg/L _+10% < 0.001 mg/L < 0.001 mg/L >99.30% >99.30%

Mercury: @ pH 6.5 0.002 mg/L 0.006 mg/L 0.006 mg/L _+10% 0.0005 mg/L 0.0003 mg/L 91.70% 95.00%

Mercury: @ pH 8.5 0.002 mg/L 0.0059 mg/L 0.006 mg/L _+10% 0.0018 mg/L 0.00073 mg/L 69.20% 88.10%

Benzene 0.005 mg/L 0.0133 mg/L 0.015 mg/L _+10% 0.0005 mg/L 0.0005 mg/L 96.10% 96.30%

p-Dichlorobenzene 0.075 mg/L 0.210 mg/L 0.225 mg/L _+10% < 0.0005 mg/L < 0.0005 mg/L >99.80% >99.80%

Carbofuran 0.040 mg/L 0.0753 mg/L 0.08 mg/L _+10% 0.027 mg/L 0.008 mg/L 64.60% 73.45%

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 _+10% < 0.001 mg/L < 0.001 mg/L >93.3% >93.3%

Atrazine 0.003 mg/L 0.0102 mg/L 0.009 mg/L _+10% 0.0027 mg/L 0.00105 mg/L 76.30% 89.40%

Asbestos >99% 126.5 MF/L 107to 108fibers/L t_ < 0.17 MF/L < 0.17 MF/L >99.99% >99.99%

Live Cysts _ >99.95% 122,500 #/L 50,000/L min. < 1 #/U < 1 #/U >99.99% >99.99%

Turbidity 0.5 NTU 10.5 NTU 11 _+1 NTU 0.30 NTU 0.125 NTU 97.30% 98.80%

Lindane 0.0002 mg/L 0.0019 mg/L 0.002 _+10% < 0.00016 mg/L 0.000035 mg/L 91.80% 97.90%

Tetrachloroethylene 0.005 mg/L 0.015 mg/L 0.015 mg/L _+10% < 0.0005 mg/L < 0.0005 mg/L >96.6% >96.6%

Test Parameters: pH = 7.5

• It is essential that operational, maintenance, and filter replacement

requirements be carried out for the product to perform as advertised.

The disposable water filter should be replaced at least every

6 months.

_+0.5 unless otherwise noted. Flow = 0.78 gpm (2.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F _+5°F (20°C _+3°C).

The filter monitor system measures the amount of water that passes

through the filter and alerts you to replace the filter. When 90% of the

filter's rated life is used, the yellow (Order) light comes on. When

100% of the filter's rated life is used, the red (Replace) light comes on,

and it is recommended that you replace the filter. For models without

filter status lights, replace the filter every 6 months. Use replacement

filter model UKF8001. 2014 suggested retail price of $44.99 U.S.A./

$49.95 Canada. Prices are subject to change without notice.

The product is for cold water use only.

Do not use with water that is microbiologically unsafe or of unknown

quality without adequate disinfection before or after the system.

Systems certified for cyst reduction may be used on disinfected

waters that may contain filterable cysts.

Refer to the "Water Filtration System" section for the Manufacturer's

name and telephone number.

Refer to the "Warranty" section for the Manufacturer's limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well

Water Pressure 35 - 120 psi (241 - 827 kPa)

Water Temperature 33° - 100°F (1° - 38°C)

Service Flow Rate 0.78 gpm (2.9 L/min.) @60 psi

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

tThese contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

ttFibers greater than 10 um in length

_Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

Interior Water Filtration System

Model UKF8001AXX-200 Capacity 200 Gallons (757 Liters)

(_ System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of

Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI Standard 53 for the reduction of Lead,

Mercury, Atrazine, Benzene, p-Dichlorobenzene, Carbofuran, Toxaphene, Cysts, Turbidity, Asbestos,

O-Dichlorobenzene, Ethylbenzene, Chlorobenzene, Endrin, Tetrachloroethylene and Lindane.