Feather River Doors 131101-3A3 Guía de instalación

Marca: Feather River Doors

Modelo: 131101-3A3

Tipo: Guía de instalación

DOC1INSF 6/15

FIBERGLASS DOOR SYSTEM

Installation Instructions

Thank you and congratulations. You have just

purchased a premier fiberglass entry door system. If

you have purchased an unfinished door system, we

recommend that you paint/stain before installation.

Refer to the finishing instructions section in this

document. Please follow the instructions carefully for

proper installation.

CAUTION: Some door units are heavy and may

require two people to lift and install. Use proper

lifting techniques and follow safe working practices.

Tools and materials needed:

Tape measure, Hammer, Square, Level, Wooden shims,

#3 Phillips screwdriver, #8 x 3" Exterior grade wood

screws, Power drill with Phillips drill bit, Safety glasses,

Caulking gun, quality clear exterior sealant, Putty

PARTS OF A DOOR SYSTEM

Before you begin:

1. Do not remove the plastic door plug until instructed

to do so. This is used to keep the door system closed

and aligned. If the door unit has handles on the latch

and hinge jambs, remove them. Also, cover the door

sill to protect against harmful particles or scratches

during installation or between a long period of building

construction and occupation. Note that any contact

with wet cement or cement powder will damage the sill

finish.

2. Make sure that the new door will properly fit in your

frame opening. The recommended rough opening is

3/4" wider and 1/2" higher than the door prehung unit.

Resize the opening if needed. Verify that the frame

opening is level, square and plumb. It is important that

the floor is level. Minor out of level conditions at the

sides and top can be corrected by using shims but

major misalignments need to be corrected before

installation. Diagonal measurements must be equal to

within 1/4" (as shown below). Note that the latch jamb

should be adjusted for plumb so that the weatherstrip

on the latch jamb is evenly compressed when the door

is closed. Use a Carpenter’s square and level to check

for squareness, level and plumb of the frame opening.

hinge

brickmold

door sill

hinge

jamb

latch

jamb

head

brickmold

door sweep

head jamb

latch

brickmold

Square

Level

DOC1INSF 6/15

INSTALLATION:

IMPORTANT: Before setting the door unit into the

rough opening, apply generous beads of caulk to the

underside of the door sill at locations shown in Figure

1a/1b, including the bottom of jambs (or plastic jamb

adapters as shown) and brickmolds. Make sure that

at least 4 lines of bead seal the full width of the sill.

Figure 1a

(In-swing)

Caulk

Figure 1b

(Out-swing)

Caulk

These jambs are shipped with predrilled counterbores. To

install the door unit to a door opening, simply predrill for #8

countersink holes through the counterbores per Figure 2c.

Temporarily secure the door unit by driving 3" wood screws

at top and bottom counterbores of each jamb.

Permanently fasten 3" exterior grade wood screws (not

included) through the jambs into the shim and the frame. Do

not over tighten the screws. Over tightening may cause

jambs to bow. Remove excess shims. Do not shim or fasten

the head jamb of the single door unit. Use putty to hide the

screw head. For a door unit with hand stained PVC jambs,

plug the screw holes with the screw caps that are included.

PVC Jambs – See addendum for additional information.

Additional Anchoring for Single Door with Sidelites

Shim above mullion per Figure 2d. Predrill 1/8" holes and

permanently fasten 3" exterior grade wood screws (not

included) through head jamb into the shim and the frame. For

hand stained PVC jambs, use the provided counterbores for

predrilling countersink holes for #8 wood screws as

mentioned in previous section and plug the screw holes with

the screw caps that are included. Remove excess shim.

Figure 2d

Shim

Inside

Figure 2b

Shim

Inside

For a single door, remove the bolt from the plastic

door plug. From outside, set the door unit into the

opening per Figure 2a. For a heavier door system,

get help when lifting, setting and aligning.

Figure 2a

Outside

From the inside, place a solid shim directly behind

each hinge between the hinge jamb (or approx.

same level as hinges on lock jamb or sidelite jamb)

and opening frame per Figure 2b. Keep the door

unit level, square and plumb on all four sides.

Remove the plastic door plug completely.

Make sure weatherstrip

contact and margin are

equal all around. Make

further adjustments for

level, square and plumb.

When adjustments are complete,

predrill 2 (3 for 8ft door)

additional equally spaced 1/8"

holes for each side of jamb. For

hand stained PVC jambs, use

the provided counterbores for

predrilling countersink holes for

#8 wood screws.

Door unit with wood or PVC jambs:

Predrill 1/8" holes at about 8" from the top and bottom of

each jamb next to a door opening. Temporarily secure the

door unit to the opening by driving 3" wood screws.

However do not drive the screws all the way at this time.

Additional shims may be used to

keep the door aligned. Test to

ensure proper operation of the door

Figure 2c

Single/Double Door

Shim

Predrill

Use 3 or 4 solid shims

between the latch jamb and

opening frame per Figure 2b.

Door unit with Hand Stained PVC jambs:

Hand

Stained

PVC

Jamb

Door with Sidelite(s)

Shim

Predrill

DOC1INSF 6/15

Additional Anchoring and Drilling for Double Door Units

Predrill 1/8" holes and permanently fasten 3" exterior

grade wood screws (not included) through the head

jamb into the frame at locations shown in Figure 2e.

For hand stained PVC jambs, use the provided

counterbores for predrilling countersink holes for #8

wood screws as mentioned in previous section and plug

the screw holes with the screw caps that are included.

Do not shim.

Inside

Screws(2)

Figure 2e

Installing Astragal Retaining Plate & Grommet for

Double Door Units

After the double door is properly aligned, use the

astragal bolts to mark and drill 3/8" diameter x 1 3/8"

min. deep hole through the head jamb and 5/8"

diameter x 1 3/8" min. deep hole through the sill, per

Figures 2f, 2g, and 2h. Pre-drill (2) 1/16" pilot holes for

the mounting screws for the head jamb. Install the

retaining plate in the head jamb using the included

hardware and insert the grommet into the 5/8"

diameter hole in the sill.

Figure 2f

Position Strike/Deadbolt Plates for Double Door Units

Close both doors. Mark desired positions for strike and

deadbolts plates. Loosen the retainer screws (do not

completely remove screws). Place the strike and

deadbolt plates into position (left image of Figure 2h)

and tighten the screws. Only use the screws that came

in the retainers. Do not use other screws as this may

cause a malfunction in the operation of the doors.

Check positions and adjust as needed.

Install Trim Covers for Double Door Units

Cut the Trim Covers so that the ends fit under both the strike

and deadbolt plates and butt up against the strike and

deadbolt retainers (as shown in the right side of Figure 2i

[1,2,3]).

Loosen the screws on the strike and deadbolt plates and slip

the Trim Cover underneath. Snap the Trim Covers into place

and tighten screws.

Install 2 screws at the location

shown in Figure 3 on the top

hinge and 1 each on the lower

2 or 3 (8ft door) hinges (screws

included in installation kit).

Figure 3

#9 x 2 1/4" screw

Figure 4

(In-swing only)

#3 Phillips screwdriver

Threshold

For an in-swing door with adjustable threshold, adjust the

threshold as shown in Figure 4 so that there is even contact

between the door sweep and the threshold. To test, put a

sheet of paper between door sweep and threshold, close the

door and pull. The correct adjustment would have slight

tension, but if the paper tears, the tension is too high.

Figure 2i

Figure 2g

(In-swing sill)

Figure 2h

(Out-swing sill)

DOC1INSF 6/15

Paint Finish

Tan woodgrain or unpainted/pre-painted smooth fiberglass doors are paintable with most high quality

oil based exterior paints. For the unpainted smooth doors, we recommend lightly sanding with 600-grit sandpaper for

the best results. Before applying a paint, wipe the fiberglass door and door lite frame with a damp cloth to remove any

dirt, oil, or debris. Allow the surface to fully dry before painting. Paint the door in the directions shown in Figure 6. Apply

at least two coats of paint. Follow the brand’s recommended drying time between coats.

Figure 6

IMPORTANT: To prevent moisture from getting inside the siding wall, completely caulk around the brickmolds per Figure

5a. For in-swing doors, install two corner seal pads (included in the installation kit) at each of the jamb bottoms of an

active door per Figure 5b. For a double door system, verify that a corner seal pad is installed at the bottom of the active

door side of an astragal. The corner seal pad should be tucked underneath the weatherstrip. Caulk at the intersection of

the jambs, brickmolds, threshold and floor. For out-swing doors, also caulk at the intersection of the jambs, brickmolds,

threshold and floor per Figure 5c.

Figure 5c (out-swing)

Weatherstrip

Corner

seal pad

Figure 5b (in-swing)

Caulk

Staining or painting an unfinished Feather River fiberglass door has never been easier. Our fiberglass door does not require

special stain kits or primer. Use the same exterior stain or paint you would use for finishing your home’s other trims. Note

that a tan woodgrain and unpainted smooth door must be finished within 6 months after the door is purchased.

When finishing, remove the door from the frame and place door in a flat level surface off the floor. Sidelites need to be

finished while attached to the frame.

Stain Finish

All surfaces of a tan woodgrain door are stainable. Our patented textured fiberglass door surface

yields superior stain adhesion without sanding. Select a high quality water-based stain from

Minwax

or Behr

or a high quality gel stain from Minwax

or Olympic

. Or, select a high quality

oil-based stain from Ace

, Minwax

, or Zar

. Before applying a stain, wipe the fiberglass door and

door lite frame with a damp cloth to remove any dirt, oil, or debris. Allow the surface to fully dry

before staining. Apply an even amount of stain with a brush or lint-free cloth in the direction of the

wood grain as shown in Figure 6. Work the stain into the surface. Lighten stain and remove

excess through wiping with a clean rag before stain dries completely. For a darker appearance,

apply a second coat after first coat dries. Follow the application instructions on the stain container

label. After stain has dried for at least 24 hours, apply three coats of high quality exterior grade

satin or low gloss polyurethane in the direction of the wood grain. Follow the label’s drying time

between coats. Important: Use polyurethane with ultraviolet (UV) inhibitors.

FINISHING INSTRUCTIONS

Caution: Paint or stain in a well ventilated area. Keep combustible paint, stain

and topcoat away from heat and flame. Keep out of reach of children.

Finishing Wood and Unfinished PVC Components

Both the pre-finished and unfinished fiberglass doors have the option to come with PVC jambs and brickmold or wood

jambs and brickmold (Primed Pine or Clear Pine).

Clear Pine Components: We recommend staining the jambs,

brickmolds and other clear wood components or stainable astragals per above stain finish instructions. Apply 2 or 3 coats

of exterior grade polyurethane with ultraviolet (UV) inhibitors. Lightly sand with 600-grit sandpaper between coats for

smoother finish. Painting Primed Wood and Unfinished PVC: Use a quality exterior grade acrylic latex or oil-base paint.

Use wood filler to putty the nail marks on the wood components before staining or painting and a PVC filler or caulk on

PVC components. Wood components must be finished within 2 weeks after installation. PVC components must be

finished within 6 months after installation.

Figure 5a

NOTE FOR STAINABLE ASTRAGAL: To protect the integrity of the wood veneer and its bonding adhesive, do not expose

the astragal to oils, thinners, solvent based cleaners or similar items. The stainable astragal should be finished prior to

being installed to the door opening and exposure to the weather.

Caulk

Please follow our standard set of installation instructions when installing this door unit. Below are some additional tips as it relates to

installing this type of jamb system. This jamb material can be nailed or screwed to install the unit but it is highly recommended to pre-drill

this material prior to applying any fastener, especially on the pre-colored material due to the ﬁnish (may cause cracking or ﬂaking).

1) Jamb Installation: Please follow the set of Feather River Installation Instructions included with the door unit purchased. You can

fasten the jambs by pre-drilling holes and securing with a #8- 3" exterior grade screw. See drawings below.

a. Included in this installation packet will be 10-Phillip head screw caps that complement the color of the PVC jamb system.

These tap caps press on top of a Phillips head counter sunk screw. For a pre-colored jamb (with a stain color): Also

included is a putty stick that complements the pre-colored jamb, this can also be utilized to ﬁll any fastening points.

b. For larger jamb sizes (6-9/16" to 8-9/16") it is sometimes recommended to fasten the jamb in two locations along the

width of the jamb.

2) Brickmold Application:

a. PVC Brickmold can be applied in a similar fashion to wood. It is always recommended to use an exterior

grade ﬁnish nail and pre-drill any fastening location, especially on the pre-colored material.

b. To keep 45˚ top angle closed/tight it may be necessary to pre-drill and apply a screw or nail through top of brickmold.

c. Once installation is complete remember to caulk around the brickmold.

d. Pre-Colored Brickmold (with a stain color): Putty stick can be used to ﬁll any fastening points.

3) Interior Trim Installation:

a. Make sure any fastening point into the pre-colored/hand stained PVC jamb system is pre-drilled prior to nailing

with a ﬁnish nail. Nail holes would be covered up using caulk or wood putty depending on type of trim being applied.

4) Storm/Security Door Application: IMPORTANT

a. Non-Vented Storm Doors will void the warranty on any Feather River Door due to the extreme heat build-up if not

properly vented.

b. If applying a storm door over this unit it is recommended that any fastening point be pre-drilled.

c. Feather River will not be responsible for any damage that may occur with the installation of a Storm/Security door setup.

Para la instalación de esta unidad, siga las instrucciones habituales. Debajo, encontrará información adicional acerca de la instalación de este tipo de sistema de marco.

Durante la instalación, pueden utilizarse clavos o tornillos directamente sobre el material del marco. Sin embargo, es recomendable taladrar o hacer los oriﬁcios con anterioridad

para proteger el acabado, en especial si el marco es de color, de lo contrario, el acabado se puede agrietar o descascarar.

1) Instalación del marco: siga las instrucciones de instalación de Feather River que vienen con la abertura. Para atornillar el marco, haga primero los agujeros con un taladro y

luego coloque un tornillo para exteriores número 8 de 3 pulgadas. Vea las ilustraciones que aparecen a continuación.

a. El paquete para la instalación incluye 10 tapas para tornillos con cabeza Phillips que se adecuan al color del marco. La tapa se coloca a presión sobre el tornillo avellanado

Phillips. Para una jamba pre-coloreado (con un color de la mancha): También se incluye un palo masilla que complementa el color de la jamba, esto puede también ser

utilizada para llenar los puntos de ﬁjación.

b. Para marcos más grandes (6-9/16" a 8-9/16") es recomendable colocar dos tornillos a lo largo del ancho.

2) Aplicación de la moldura:

a. La moldura de PVC se coloca de manera similar a una moldura de madera. Es recomendable utilizar clavos de acabado para exteriores y

taladrar los oriﬁcios para los tornillos de antemano, especialmente en las molduras de color.

b. Para mantener el ángulo superior ﬁjo a 45˚, es posible que necesite colocar un tornillo o un clavo a través de la parte superior de la moldura.

c. Una vez terminada la colocación, recuerde aplicar masilla alrededor de la moldura.

d. Moldura pre-coloreado (con un color de la mancha): La palo de la masilla se puede utilizar para llenar cualquier puntos de ﬁjación.

3) Colocación del contramarco:

a. Al colocar un marco de color o pintado con tinte, asegúrese de hacer todos los oriﬁcios antes de clavar los clavos de acabado.

Los oriﬁcios de los clavos se pueden cubrir con masilla o con masilla para madera según el tipo de contramarco que haya colocado.

4) Colocación de la puerta de seguridad/contrapuerta: IMPORTANTE

a. Las puertas de seguridad sin entrada de aire invalidan la garantía de cualquier puerta Feather River debido a la cantidad excesiva

de calor que se acumula cuando no se ventilan adecuadamente.

b. Al colocar una puerta de seguridad, es recomendable que todos los oriﬁcios para los tornillos se hagan con anterioridad.

c. Feather River no se responsabiliza por los daños que puede causar la colocación de una puerta de seguridad o contrapuerta.

Instalación - AnexoMarco de material PVC –

Blancas sin acabado • Pre-coloreado

PVC JAMB SYSTEMS

White Unnished • Pre-Colored

INSTALLATION

ADDENDUM PAGE

WEATHERSTRIP

Burlete

WEATHERSTRIP

Burlete

JAMB

Marco de la puerta

SHIM

Cuña

SHIM

Cuña

BRICKMOLD

Moldura

WALL STUD

Marco de la pared

SINGLE DOOR w/SIDELITE(s)

Puerta con una o más ventanas laterales

SINGLE/DOUBLE DOOR

Puerta simple o doble

BRICKMOLD

APPLICATION

(Step B above)

Moldura colocación

(Ver paso B mencionado anteriormente)

SCREW TAP CAP

Tapa para tornillo

JAMB

Marco

SHIM

Cuña

SHIM

Cuña

BRICKMOLD

Moldura

WALL STUD

Marco de la pared

PRE-DRILLING DETAILS

Detalles De Perforación Previa

On single and double doors, holes are pre-drilled and countersunk behind the weatherstripping illustrated below by the

arrows. Doors with sidelites have pre-drilled holes on the face of jambs (plugs provided). Door should still be shimmed and

installed following the regular installation instructions provided with this unit.

1) Jamb Installation: Please follow the set of Feather River Installation Instructions included with the door unit purchased.

a. See pre-drilled fastening locations shown below for Single/Double Setups and Doors w/ Sidelite(s).

b. For sidelite units screw plugs are provided.

c. For larger jamb sizes (6-9/16") it is sometimes recommended to fasten the jamb in two locations along the width of

the jamb if necessary. Any additional fastening point should be pre-drilled and can be ﬁlled with a putty stick to

complement the stain ﬁnish. (Putty stick supplied in installation packet.)

2) Brickmold Application: Brickmold supplied is a hand stained PVC material. This can be nailed into place using exterior

grade trim nails. It is recommended that any fastening point be pre-drilled since this is a stained material. Any fastening locations

can be ﬁlled with a putty stick or stained over using a touch up marker. Both complement the stain ﬁnish and are supplied in the

installation packet.

a. To keep 45˚ top angle closed/tight it may be necessary to pre-drill and apply a screw or nail through top of brickmold.

b. Once installation is complete remember to caulk around the brickmold.

c. Pre-Colored Brickmold (with a stain color): Putty stick can be used to ﬁll any fastening points.

3) Interior Trim Installation:

a. Make sure any fastening point into the hand stained PVC jamb system is pre-drilled prior to nailing with a ﬁnish nail.

Nail holes would be covered up using caulk or wood putty depending on type of trim being applied.

4) Storm/Security Door Application: IMPORTANT

a. Non-Vented Storm Doors will void the warranty on any Feather River Door due to the extreme heat build-up if not

properly vented.

b. If applying a storm door over this unit it is recommended that any fastening point be pre-drilled since the brickmold or

mull caps are a pre-stained material.

c. Feather River will not be responsible for any damage that may occur with the installation of a Storm/Security door setup.

Note: Orders for Florida and Texas TDI Areas may not be pre-drilled due to building codes that require different fastening locations for installation.

Nota: Los pedidos de Florida y zonas de Texas TDI no pueden ser pre-perforados debido a los códigos de construcción que requieren de diferentes lugares de ﬁjación para la instalación.

En puertas simples y dobles, los oriﬁcios se hacen con anterioridad y se avellanan detrás del burlete como muestran las ﬂechas en la ilustración. Las puertas con ventanas laterales

traen los oriﬁcios ya hechos en las caras del marco. (Incluye tornillos.) Aún así, se deberá calzar y colocar la puerta siguiendo las instrucciones que vienen con la unidad.

1) Instalación del marco: Siga las instrucciones de instalación de Feather River que vienen con la abertura.

a. Para puertas simples o dobles con ventanas laterales, observe en la ilustración siguiente dónde se ubican los oriﬁcios para sujetar la abertura.

b. Las ventanas laterales incluyen los tapones roscados.

c. Para marcos más grandes (6-9/16") es recomendable colocar dos tornillos a lo largo del ancho. Cualquier punto de ﬁjación adicional debe ser pre-perforados

y puede ser llenado con masilla para complementar el acabado mancha. (La palo de la masilla se suministra en paquetes de instalación.)

2) Aplicación de la moldura: La moldura está pintada a mano con tinte y realizada de PVC. Para sujetarla, se pueden utilizar clavos de acabado para exteriores.

Es recomendable que todos los oriﬁcios se hagan antes de colocarla, ya que el material está pintado con tinte. Las marcas de clavos o tornillos se pueden

tapar con el palo de la masilla o utilizando un marcador para retoques. Ambos se complementan el acabado y se suministran en el paquete de instalación.

a. Para mantener el ángulo superior ﬁjo a 45˚, es posible que necesite colocar un tornillo o un clavo a través de la parte superior de la moldura.

b. Una vez terminada la colocación, recuerde aplicar masilla alrededor de la moldura.

c. Moldura pre-coloreado (con un color de la mancha): La palo de la masilla se puede utilizar para llenar cualquier puntos de ﬁjación.

3) Colocación del contramarco:

a. Al colocar el marco pintado a mano, asegúrese de hacer todos los oriﬁcios antes de clavar los clavos de acabado. Los oriﬁcios

de los clavos se pueden cubrir con masilla o con masilla para madera según el tipo de moldura que haya colocado.

4) Colocación de la puerta de seguridad/contrapuerta: IMPORTANTE

a. Las puertas de seguridad sin entrada de aire invalidan la garantía de cualquier puerta Feather River debido

a la cantidad excesiva de calor que se acumula cuando no se ventilan adecuadamente.

b. Al colocar una puerta de seguridad, es recomendable que todos los oriﬁcios para los tornillos se hagan

con anterioridad ya que las molduras y los tapacantos vienen prepintados con tinte.

c. Feather River no se responsabiliza por los daños que puede causar la colocación de una puerta de

seguridad o contrapuerta.

Instalación - AnexoMarco de material PVC pintado con tinte a mano

HAND STAINED PVC JAMB SYSTEM

INSTALLATION ADDENDUM PAGE

WEATHERSTRIP

Burlete

SINGLE DOOR w/SIDELITE(s)

Puerta con una o más ventanas laterales

WEATHERSTRIP

Burlete

JAMB

Marco de la

puerta

SHIM

Cuña

SHIM

Cuña

BRICKMOLD

Moldura

WALL STUD

Marco de la

pared

SINGLE/DOUBLE DOOR

Puerta simple o doble

Hole Locations

Ubicaciones agujero

BRICKMOLD

APPLICATION

(Step B above)

Moldura colocación

(Ver paso B mencionado

anteriormente)

JAMB

Marco

SHIM

Cuña

SHIM

Cuña

BRICKMOLD

Moldura

WALL STUD

Marco de la

pared

PRE-DRILLING DETAILS

Detalles De Perforación Previa

PLUG

Tapón

DOC1INSF 6/15

CARE AND MAINTENANCE

Hand stained Jambs, Brickmolds and Doors: Over time, harsh weathering will degrade even the best finish. We

recommend reapplying a UV topcoat over the existing topcoat every 2-3 years. We do not recommend stripping the

factory finish topcoat. In locations of severe weather exposure, more frequent maintenance may be required. Fading,

minor cracking and peeling are some initial signs of UV topcoat deterioration.

Painted Fiberglass Doors, PVC Components, and Wood Components:

Repaint your doors, jambs and brickmolds as

soon as deterioration occurs. Initial signs of wear are fading, cracking, bubbling, and peeling.

Weatherstrip: Replace compression weatherstrip, door sweep, and seal pads when worn or torn.

Caulking: Just as with the finish, it is imperative that deterioration of caulking/sealant is properly maintained. Any areas

of deterioration should be re-caulked based on the areas pointed out in the installation instructions (Exterior Trim to

Exterior Façade, Exterior Trim to Jamb, Jamb Base to Threshold/Sill). Note: All Feather River fiberglass door lite frames

come pre-caulked from the factory. The excess sealant on the door lite is normal and does not indicate a defective

glazing. In some cases over time, you may experience excess caulking/sealant ooze around the lite frame. In most

cases this happens during extreme heat buildup or when the door is exposed to direct sunlight. The excess sealant on

the glass can be removed by carefully scoring the excess sealant with a razor blade and peeling it off. The excess

sealant on the glass side may be better removed with the blade after scoring. However for the sealant on the finish side,

the sealant should be removed without using the blade after the initial scoring around the perimeter of the frame.

Door Lite Plugs: Every door with a lite comes with enough plugs to fill all screw holes. All screw plugs should have a

tight fit when installing to keep from falling out. To install screw plugs, line up screw plug with hole and insert at a slight

angle to get started. In some cases you may be able to push the plug into place with hand. In most cases, you will

need to take a small round head hammer and lightly tap into place or take the handle part of a screwdriver and tap into

place with a hammer. If it seems that the screw plugs are too tight to fit into the plug holes, place the screw plug packet

in a freezer for about an hour prior to installing or slightly sand or file bottom side of the plug to help plug get started in

the plug hole.

Thermal Bowing: In some areas with temperature fluctuations, your door may experience signs of bowing over a period

of days. This is typically due to the temperature difference between the exterior and interior part of the home. In most

cases the door should return back to it’s normal position. This is also common during the first couple of weeks after the

door is installed while the door becomes acclimated to the opening. However in areas or conditions of extreme

temperature exposure on the door, some permanent bowing can be expected. In the areas of extreme temperature

exposure, the effect of the temperature on the door can be reduced by following some recommendations listed below.

Door Exposure and Protection: Doors protected by the elements will obviously need less maintenance and re-finishing

vs. doors fully exposed to the elements. So overhangs will help provide long lasting protection to your entryway along

with reduced maintenance.

Color Choice: As with overhangs, door colors may help reduce periodic maintenance and help with the door

performance, especially in areas where doors receive an extreme amount of sun without protection. Dark colors will

absorb more heat than the light colors. So if a door is absorbing a lot of heat or has constant sun exposure, it is more

likely to have UV topcoat deterioration, color fading, and even issues with warping due to differential temperature. Light

colors in these situations will help reduce the amount of heat absorption and help prolong the life of the door and reduce

the overall maintenance.

Storm Doors: Our doors are energy efficient and storm door protection is not necessary. If purchasing a storm door,

keep in mind that it should be ventilated to help reduce the amount of heat buildup. Full View non-ventilated storm

doors in areas where no overhang and constant sun exposure is present will most likely lead to accelerated issues

pointed out above due to the extreme heat (UV deterioration, color fading, warping, caulk/sealant oozing).

Feather River Doors 131101-3A3 Guía de instalación

Marca: Feather River Doors

Modelo: 131101-3A3

Tipo: Guía de instalación

Descargar PDF

informe

En otros idiomas

English: Feather River Doors 131101-3A3 Installation guide

Feather River Doors 131101-3A3 Guía de instalación

Feather River Doors 131101-3A3 Guía de instalación

En otros idiomas

Documentos relacionados

Otros documentos