Magic Chef MCSCWD27W5 El manual del propietario

Marca: Magic Chef

Modelo: MCSCWD27W5

Categoría: Lavadoras

Tipo: El manual del propietario

Este manual también es adecuado para

MCSFLW27W

PLEASE READ THIS MANUAL CAREFULLY BEFORE USING YOUR

COMBO WASHER AND DRYER AND KEEP IT FOR FUTURE REFERENCE.

Model MCSCWD27W5 / MCSFLW27W

24” Combo Washer and Dryer

24” Front Load Washer

User’s Manual

PRODUCT REGISTRATION

Thank you for purchasing a Magic Chef® product� The first step to protect your new product is to complete the product

registration on our website: www�mcappliance�com/register� The benefits of registering your product include the following:

1� Registering your product will allow us to contact you regarding a safety notification or product update�

2� Registering your product will allow for more efficient warranty service processing when warranty service is required�

3� Registering your product could act as your proof of purchase in the event of insurance loss�

Once again, thank you for purchasing a Magic Chef product�

CONTENTS

PRODUCT REGISTRATION � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2

IMPORTANT SAFETY INSTRUCTIONS � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4

SPECIFICATIONS� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6

INSTALLATION INSTRUCTIONS � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7

BEFORE USE � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10

OPERATION INSTRUCTIONS� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11

WASH CYCLE PARAMETERS� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �17

CARE AND MAINTENANCE � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 19

TROUBLESHOOTING� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22

LIMITED WARRANTY � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 24

IMPORTANT SAFETY INSTRUCTIONS

This manual contains Safety Instructions, Installation and Operating Instructions, and Troubleshooting Tips� Please

carefully read this manual before using your washing machine for instructions on how to use and maintain the

product properly� Be sure to follow the safety instructions to avoid injury or damage to the product�

Keep this manual� When passing on/selling the device to a third party, the manual must be handed over along

with the device�

Before calling for service, please make sure unit is installed and being used correctly, and read the troubleshooting

section�

WARNING: When using your appliance, follow the precautions listed below�

NOTE: Specifications may change at any time without notice�

State of California Proposition 65 Warnings

WARNING: The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of

California to publish a list of substances known to the State of California to cause cancer, birth defects, or other

reproductive harm, and requires business to warn of potential exposure to such substances� This product contains

a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm� This

appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde, and

carbon monoxide�

1� Read all instructions before using this product�

2� This appliance is for household use only� It is not intended for commercial applications�

3� The appliance is intended for indoor use only� DO NOT use outdoors�

4� DO NOT use this appliance for other than its intended purpose�

5� Use only detergents or softeners recommended for use in this manual and keep them out of the reach of

children�

6� This machine is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they are given supervision or instruction

concerning the use of the washer by a person responsible for their safety�

7� This appliance must be properly installed in accordance with the installation instructions before it is to be used�

8� DO NOT unplug your appliance by pulling on its power cord� Always grasp the plug firmly and pull it

straight out from the outlet�

9� Do not operate any appliance that has a damaged cord or plug, if it is damaged or malfunctions in any way,

or if the outlet is not in proper working order� Contact customer service or a service technician�

10� ALWAYS turn off and unplug from outlet before servicing, changing accessories or cleaning the unit� Allow

unit to cool down completely before cleaning, moving or servicing� Turning the unit off does not disconnect

it from the power source�

11� DO NOT put anything flammable or explosive in, on, or near the appliance� DO NOT wash or dry articles

of clothing or any items that have been soaked in flammable or explosive chemicals� To reduce the risk

of fire, clothes, cleaning rags, mop heads and the like which have traces of any flammable substance, such

as cooking oils, petroleum based oils or distillates, waxes, fats, etc�, must not be placed in the washing

machine� These items may contain flammable substances which, even after washing, may smoke or catch

fire� DO NOT dry articles containing foam rubber or similarly textured rubber like materials�

12� ALWAYS wait for the washer tub to completely stop moving before reaching in to add or remove any clothes�

13� The loading door must be closed when the tub is spinning�

14� DO NOT operate this washer unless all enclosure panels are properly installed�

15� DO NOT tamper with or modify the controls�

16�

WARNING: Risk of child entrapment� DO NOT allow children to play on or in the appliance� Close

supervision of children is necessary when the appliance is used around them�

17� The appliance must be plugged into a properly installed and grounded outlet that meets the voltage

requirements listed on the ratings label�

18�

CAUTION: The power cord is equipped with a 3-prong grounding plug to protect against shock hazards�

ALWAYS plug the cord into a properly installed and grounded 3-prong wall receptacle, and DO NOT remove

the grounding prong�

19� Under certain conditions, hydrogen gas may be produced in a household hot water system that has not

been used for two weeks or more� Hydrogen gas is highly explosive� If the hot water system has not been

used for more than two weeks, turn on all hot water faucets and let the water flow for several minutes

prior to using your compact washer�

20� DO NOT modify or repair the unit by yourself� Contact customer service or a qualified service technician if

service is required�

21� To reduce the risk of electric shock or fire, do not use an extension cord or outlet adapters to connect the

unit to an electrical power source� The appliance must be properly grounded using a three-prong electric

receptacle wall outlet�

22� DO NOT install the washing machine in a moist or wet area, or where it can get wet or exposed to outside

weather conditions� DO NOT spray with water when cleaning�

23� DO NOT put children on top of, or allow children or pets to climb in or on, the washer� ALWAYS check

inside before using�

24� Glass door may be very hot during the operation� Keep children and pets away from the washer while in use�

25� Regularly clean the power plug to remove dust and dirt, in order to prevent electrical failure�

26� It is recommended to unplug the unit when it is not in use�

27� ALWAYS be sure to properly and securely connect the power cord to the outlet, and the water hoses to

prevent leakage or electrical shock�

28� DO NOT operate the unit or handle the plug with wet hands�

29� The water temperature to the washing machine should not exceed 131 °F (55 °C)�

30� DO NOT wash raincoats, heavy jackets, or similar, heavy items�

31� DO NOT machine wash fiberglass materials (such as curtains and window coverings that use fiberglass

materials�) Small particles may remain in the washing machine and stick to fabrics in subsequent wash loads

causing skin irritation�

32� When removing from service and discarding, be sure to remove the door from the unit and cut the power cord�

33� DO NOT reach into the wash tub when the agitator is moving�

34�

CAUTION: Content may be HOT when washing and/or drying cycle is completed�

READ AND FOLLOW THIS

SAFETY INFORMATION CAREFULLY

SAVE THESE INSTRUCTIONS

SPECIFICATIONS

Height 33�5” (850 mm)

Width 23�5” (595 mm)

Depth 23�5” (595 mm)

Depth with Door Opened 42�5” (1080 mm)

Weight 160�9 lbs� (73�0 kg)

Voltage / Frequency AC 120V~60Hz

Rated Current 11�0A

Max� Washing Capacity 26�4 lbs� (12�0 kg)

Max� Dry Capacity (For MCSCWD27W5 only) 17�6 lbs� (8�0 kg)

Drum Size 2�7 cu� ft�

Figure 1

33�5”

(850 mm)

23�5” (595 mm)

42�5” (1080 mm)

INSTALLATION INSTRUCTIONS

1� The washing machine must be properly grounded� In the event of a short circuit, grounding can reduce the

danger of electrical shock�

2� Washing machine should be operated in a circuit separate from other electrical appliances�

INCLUDED PARTS

Before starting installation, make sure all included parts are

in the package inside the drum�

INSTALLATION REQUIREMENTS

ELECTRICAL REQUIREMENTS

1� A 120v, 60Hz, AC 15-or 20amp, fused electrical supply

is required� A time-delay fuse or circuit serving only this appliance should be used�

2� This washer is equipped with a power supply cord having a 3 prong grounding plug�

3� To minimize possible shock hazard, the cord must be plugged into a 3 prong outlet, properly grounded in

accordance with local codes and ordinances� If a proper outlet is not available, it is the responsibility of the

customer to have the properly grounded outlet installed by a qualified electrician�

4� If codes permit and a separate ground wire to be used, it is recommended that a qualified electrician

determine the proper ground path�

5� DO NOT ground to a gas pipe�

6� Check with a qualified electrician if you are not sure the washer is properly grounded�

7� DO NOT have a fuse in the neutral or ground circuit�

8� Certain internal parts are intentionally not grounded and may present a risk of electric shock only during

servicing� Service Personnel – Do not contact the following parts while the appliance is energized: Drain

Pump, Door Lock, Drying Heater (Combo), Fan Motor (Combo)�

LOCATION REQUIREMENTS

Selecting the proper location for your washer improves performance and minimizes noise and possible washer

“walk�” The washer can be installed under a custom counter or in a basement, laundry room, closet, or recessed area�

You will need:

• A water heater set for 120° F (49° C)�

• A grounded electrical outlet located within 6 ft�( 1�8 m) of where the power cord is attached to the back of

the washer�

• Hot and cold water faucets located within 4 ft� (1�2 m) of the hot and cold water fill valves ,and water

pressure of 20 - 100 psi (137�9 - 689�6 kPa)�

• A level floor with a maximum slope of 1” (25 mm) under entire washer� Installing the washer on soft floor

surfaces, such as carpets or surfaces with foam backing�is not recommended�

• A sturdy and solid floor to support the washer with a total weight (water and load) of 200lbs�

• Do not operate your washer in temperatures below 32° F (0° C)� Some water can remain in the washer and can

cause damage in low temperatures�

Water Hoses (2) Cable Tie

Transport

Hole Plugs (4)

Figure 2

• The location must be large enough to allow the washer door to be fully opened� The door opens more than

90°, and is not reversible�

• Additional spacing should be considered for ease of installation and servicing�

• Minimum spacing of 1” (25 mm) on all sides of the washer is recommended to reduce noise transfer�

• Additional clearances might be required for wall, door, and floor moldings�

• Spacing for companion appliance should also be considered�

Figure 3

Figure 4

INSTALLATION

CAUTION: Packing materials may be dangerous to children�

Please dispose them properly and DO NOT let children play with

any packing materials�

Before using this washing machine, transport bolts must be

removed from the backside of this machine� Please take the

following steps to remove the bolts:

1� Loosen all bolts and then remove them�

2� Insert the transport hole plugs into the holes�

3� Keep the transport bolts for future use�

Make sure that the small foam triangle is removed with the bottom

foam piece� If not, carefully lay the unit down and remove it�

When you unpack your washing machine, check if there is any

damage or missing pieces� If any items missing, please contact

customer service�

LEVELING THE WASHER

1� When positioning the washing machine, make sure the

legs are screwed in close to the cabinet� If not, turn them

to their original positions by hand or with a wrench and

tighten the nuts with a wrench�

2� After positioning the washing machine, push on all four

corners at the top of washing machine� If the washing

machine has any wobble, or is not stable when being

pressed, adjust the leg to level the machine�

3� To level the unit, loosen the lock nut with a wrench and

turn the leg by hand until it tightly contacts with the floor�

Press the leg with one hand and tighten the locking nut

close to the cabinet with the other hand�

4� Repeat steps 2 and 3 as needed�

5� Use a bubble level to check front to back, side to side, and

corner to opposite corner to ensure the washing machine

is level� Repeat above steps if needed�

Figure 5

Figure 6

DRAIN SYSTEM

STANDPIPE DRAIN SYSTEM

- WALL OR FLOOR

2” (5 cm)

Figure 7 Figure 8

The standpipe drain requires a

minimum diameter standpipe of 2”

(5 cm)� The minimum carry-away

capacity can be no less than 17 gal�

(64 L) per minute� The top of the

standpipe must be at least 24” (60

cm) high and no higher than 39”

(100 cm) from the bottom of the

washer�

INSTALL INLET PIPE

Connect the end of the water inlet hose with the 90°

elbow to the back of the washing machine and turn

clockwise to tighten� Note the position of the Hot and

Cold water inlets�

Connect the other end of the water inlet hose to the

appropriate Hot and Cold water tap� Tighten by turning

clockwise, and turn on the water valve to check for leaks�

If any leaks are found, verify all connections are tight and

washers are present, and repeat the procedure�

LAUNDRY TUB DRAIN SYSTEM

The laundry tub needs a minimum 20 gal� (76 L) capacity�

The top of the laundry tub must be at least 60cm above

the foor�

FLOOR DRAIN SYSTEM

The floor drain system requires a siphon break that

may be purchased separately� The siphon break must

be a minimum of 28” ( 71 cm) from the bottom of

the washer�

Additional

hoses might

be needed�

Figure 9 Figure 10

min� 24”

(61 cm)

max� 39”

(100 cm)

min� 24”

(60 cm)

max� 39”

(100 cm)

min� 28”

(71 cm)

Figure 11

Figure 12

Hot

Connector to water inlet is a 90° bend�

Cold

BEFORE USE

CHECK LIST AND PREPARATION BEFORE WASHING

Read all instructions carefully to avoid any damage or issues with the washing machine and to clothes� ALWAYS

follow instructions on fabric care labels on clothing articles for proper care�

WARNING: DO NOT leave items to be washed in the washing machine for long periods of time� Items left in the

machine may get moldy and get spots� Clothes may also become discolored if they are not washed according to the

stated washing temperature and instructions�

SELECTING DETERGENT

• Low foaming powdered detergent is recommended for use with the washing machine�

• Some detergents may not completely dissolve if there is too much detergent or if the water temperature is

too low�

• Bleach can damage clothes� Use bleach with caution and follow detergent and clothing article care

instructions�

Washing method is based on weight of clothes, soil level, local water hardness as well as the recommendations

from the detergent manufacturers�

NOTE: DO NOT place or store laundry products, such as detergent, bleach, or liquid fabric softener, on top of

your washer/dryer combo unit� Wipe up any spills immediately� These products can damage the finish and controls�

Keep all laundry products in a safe, dry space out of reach of children�

SEPARATE CLOTHES TO BE WASHED

Classify clothes to be washed into cottons, blended fibers, synthetic fibers, silks, wools, etc� Light and dark clothes

should also be separated�

NOTE: New, colored fabrics should be washed separately�

• Accessories: Loose accessories on some clothes may become damaged and/or damage the washing machine�

Clothes that contain buttons or embroideries should be turned inside-out before being washed�

• Fasteners: Zippers must be closed and buttons or hooks must be firmly affixed� Any loose bands or ribbons

should be tied together before being washed�

• Water-proof materials: It is not recommended to wash water-proof fabrics as they may become damaged

and/or cause damage to the washing machine and other items being washed�

REMOVE ALL LOOSE OBJECTS FROM CLOTHES

Check all pockets/compartments of clothes to be washed and remove any loose items such as coins� Loose items

may damage the washing machine�

BALANCING THE LOAD

Washing large, heavy garments, such as towels, jeans, jackets etc�, may cause an unbalanced load� It is suggested to

add one or two more items to balance the load to allow smooth and complete draining�

OPERATING INSTURCTIONS

CONTROL PANEL (FOR MCSCWD27W5 ONLY)

a� On/Off: Press [On/Off] to turn the unit ON� Press the button again to turn the unit OFF�

NOTE: If the washer is programmed for a wash cycle and is not started within 10 minutes, the cycle will be

cancelled and the unit will automatically turn OFF�

b� Start/Pause: Press [Start/Pause] to start a wash cycle� Press [Start/Pause] again to pause the cycle when

the washer is running� Press [Start/Pause] once more to resume� To add a garment after the wash cycle has

started, push this button for 3 seconds before the drum has filled with water� This can only be done in the

beginning of the cycle before the water reached the bottom of the door� Wait for the drum to stop and the

door to unlock, then add item(s)� Close door and press [Start/Pause] to continue washing�

c� Wash Cycles

1� My Cycle: Select this option to save a commonly used washing program as a preset�

• To program, select the settings you wish to use, and then press and hold [Spin] for 3 seconds to save�

2� Quick Wash: Select this option to wash small loads of clothing that are not very dirty quickly�

3� Delicates: Select this option for delicate fabrics such as dress shirts, nylons, etc�

• Wash cycle operates at a lower temperature�

4� Wool: Only use this option to wash wool clothing articles labeled “Machine Washable”�

• Proper detergent and water temperature must be selected for wool textiles�

• Lower spin speed and less agitation

5� Baby Wear: For washing infant clothing

6� Sanitary: Uses hot water to allow enzymes in detergent to work more efficiently for hard to clean or

heavily soiled items�

7� Normal/Cotton: Select this option for regularly used cottons and fabrics�

• Extended wash cycle with stronger intensity

• Recommended fabrics: cotton, linens, bed sheets, t-shirts, towels, jeans, etc�

• Dry cycle can be added.

Figure 13

Press 3 sec. to set My Cycle

e f

l m n

h i j d c b

8� Perm Press: Moderate strength wash cycle� Used to reduce wrinkles in clothes from washing�

9� Heavy Duty: Select this option for washing heavy clothing�

• Dry cycle can be added.

10� Bulky/Large: Select this option for bulky/large items�

• Extended wash cycle

11� Sports Wear: Select this option for sportswear�

• Wash cycle cleans heavily soiled clothes�

12� Spin Only: Select this option to spin a load separately from a regular wash cycle�

• Soap water or rinse water must be drained before spinning�

13� Rinse & Spin: Select this option to rinse and spin a load separately from a regular wash cycle�

• This can be helpful in preventing fresh stains from setting in fabrics�

14� Tub Clean: Select this option to clean the wash tub� This program uses high temperatures to sterilize the

tub while removing built up detergent and residues� Add bleach for a better clean� This program should

be used at least once a month with regular use� DO NOT add any clothes or wash items for this program�

d� Dry Cycles

NOTE: Maximum drying load size is smaller than wash load size� Be sure to note the drying load size when

using�

• Auto Dry: Select this option to have dry cycle automatically set based on the load� Auto Dry program

has a 12 minute spin cycle and 45 minute cool air cycle� It is recommended to dry in multiple, smaller

loads to allow for better for performance�

• Timed Dry: Select this option to set dry cycle time manually� Timed Dry programs include a 12 minute

spin and 25 minute cool period� It is recommended to dry in multiple, smaller loads to allow for better

for performance�

Time in Minutes Capacity

58 1�8 lbs� (0�8 kg)

88 2�2 lbs� (1�0 kg)

199 6�6 lbs� (3�0 kg)

NOTE: Important Notes for Dry Cycles

For Wash only, unit can be filled to the Max� Washing Capacity, however, load sizes less than the Max� Wash

Capacity can improve performance and efficiency�

For Wash cycles plus Dry cycles or Dry only cycles, unit should not be filled over the Max� Dry Capacity

to allow the dry function to work effectively� Load sizes less than the maximum capacity will improve the

drying performance of the combo unit�

DO NOT cut off water supply or remove hose attachments during dry cycle� This is a ventless unit that

releases moisture during dry cycles� The dryer is equipped with a door-locking safety feature to ensure safe

temperatures and avoid burns and other safety hazards� The door will remain LOCKED during dry cycle until

the unit reaches a safe temperature� After a safe temperature is reached, the door should open and function

normally�

e� Time Save: Press [Time Save] to decrease the washing time�

• See Wash Cycle Parameters Table for programs that can use Time Save�

f� Delay: Press [Delay] to set a delay time for the wash to begin�

• The delay start light will flash to indicate the delay time� You can delay the start time of the cycle from

1 - 24 hours�

• Set Wash program, Press Delay to set the number of hours to delay wash cycle, then push Start/Pause�

• To cancel the delay time, press Delay button until time shows 0H�

g� Temp�: Press [Temp�] to set your desired washing temperature�

• Press button to set desired wash temp (Hot+, Hot, Warm, Eco, Cold)

h� Spin: Press [Spin] to increase spin speed�

• Washer drum spins at a speed up to 1300 RPM which reduces drying time and saves energy�

• Press the button until desired speed is lit (No Spin, Low, Med, High, Highest)�

• Some fabrics (i�e� delicates) require a slower spin speed�

• High spin speeds are not available on all cycles�

i� Soil: Press [Soil] to increase time for heavier soiled items�

• There are three (3) soil levels options�

• Each bar increases the base wash time by 15 minutes�

j� Dry Level: Press the Dry button continuously to choose the dry level: Extra Dry/Normal Dry/Gentle Dry�

k� Child Lock: Press [Delay] and [Temp] at the same time for 3 seconds to Unlock/Lock the control panel�

• On/Off Button will still function�

l� Extra Rinse: Press the [Temp�] and [Spin] button at the same time to add an extra rinse to the selected cycle�

m� My Cycle: After a wash cycle is modified, hold down [Spin] to save your settings�

• You can quickly choose this cycle for your next wash by turning the dial to My Cycle�

• Override saved settings by holding the [Spin] button down again after a different cycle and options are

selected�

n� Sound: Press the [Soil] button for 3 seconds to turn the sound on or off�

Figure 14

DISPLAY (FOR MCSCWD27W5 ONLY)

ePress 3 sec. to set My Cycl

d e f g

a� Cycle Indicator: Indicates stage of wash/dry cycle�

•

: Prewash • : Wash • : Rinse • : Spin

•

: Time Save • : Extra Rinse • : Dry

b� Clock: Indicates time left until the end of wash/dry cycle�

c� Feature Indicator: Indicates features that are active�

•

Sound: Indicates that sounds are on� When unlit, unit is muted�

•

Door Lock: Machine is locked for duration of cycle�

•

Child Lock: Child lock is on�

•

Add a Garment

d� Water Temperature: Indicates the selected temperature�

e� Spin Speed: Indicates the selected spin speed�

f� Soil Level Indicator: Indicates the selected soil level�

g� Dry Level: Indicated the selected dry level�

•

Extra Dry • Normal Dry • Gentle Dry

NOTE: Maximum drying load size is smaller than wash load size�

CONTROL PANEL (FOR MCSFLW27W ONLY)

a� On/Off: Press [On/Off] to turn the unit ON� Press the button again to turn the unit OFF�

NOTE: If the washer is programmed for a wash cycle and is not started within 10 minutes, the cycle will be

cancelled and the unit will automatically turn OFF�

b� Start/Pause: Press [Start/Pause] to start a wash cycle� Press [Start/Pause] again to pause the cycle when

the washer is running� Press [Start/Pause] once more to resume� To add a garment after the wash cycle has

started, push this button for 3 seconds before the drum has filled with water� This can only be done in the

beginning of the cycle before the water reached the bottom of the door� Wait for the drum to stop and the

door to unlock, then add item(s)� Close door and press [Start/Pause] to continue washing�

c� Wash Cycles

1� My Cycle: Select this option to save a commonly used washing program as a preset�

• To program, select the settings you wish to use, and then press and hold [Spin] for 3 seconds to save�

Figure 15

d e

k l

g h i c b

Press 3 sec. to set My Cycle

2� Quick Wash: Select this option to wash small loads of clothing that are not very dirty quickly�

3� Delicates: Select this option for delicate fabrics such as dress shirts, nylons, etc�

• Wash cycle operates at a lower temperature�

4� Wool: Only use this option to wash wool clothing articles labeled “Machine Washable”�

• Proper detergent and water temperature must be selected for wool textiles�

• Lower spin speed and less agitation

5� Baby Wear: For washing infant clothing

6� Sanitary: Uses hot water to allow enzymes in detergent to work more efficiently for hard to clean or

heavily soiled items�

7� Cold Wash: Only uses cold water�

8� Tub Clean: Select this option to clean the wash tub� This program uses high temperatures to sterilize the tub

while removing built up detergent and residues� Add bleach for a better clean� This program should be

used at least once a month with regular use� DO NOT add any clothes or wash items for this program�

9� Normal/Cotton: Select this option for regularly used cottons and fabrics�

• Extended wash cycle with stronger intensity

• Recommended fabrics: cotton, linens, bed sheets, t-shirts, towels, jeans, etc�

10� Perm Press: Moderate strength wash cycle� Used to reduce wrinkles in clothes from washing�

11� Heavy Duty: Select this option for washing heavy clothing�

12� Bulky/Large: Select this option for bulky/large items�

• Extended wash cycle

13� Sports Wear: Select this option for sportswear�

• Wash cycle cleans heavily soiled clothes�

14� Spin Only: Select this option to spin a load separately from a regular wash cycle�

• Soap water or rinse water must be drained before spinning�

15� Drain Only: Used to drain any water in the unit�

16� Rinse & Spin: Select this option to rinse and spin a load separately from a regular wash cycle�

• This can be helpful in preventing fresh stains from setting in fabrics�

d� Time Save: Press [Time Save] to decrease the washing time�

• See Wash Cycle Parameters Table for programs that can use Time Save�

e� Delay: Press [Delay] to set a delay time for the wash to begin�

• The delay start light will flash to indicate the delay time� You can delay the start time of the cycle from

1 - 24 hours�

• Set Wash program, Press Delay to set the number of hours to delay wash cycle, then push Start/Pause�

• To cancel the delay time, press Delay button until time shows 0H�

f� Temp�: Press [Temp�] to set your desired washing temperature�

• Press button to set desired wash temp (Hot+, Hot, Warm, Eco, Cold)

g� Spin: Press [Spin] to increase spin speed�

• Washer drum spins at a speed up to 1300 RPM which reduces drying time and saves energy�

• Press the button until desired speed is lit (No Spin, Low, Med, High, Highest)�

• Some fabrics (i�e� delicates) require a slower spin speed�

• High spin speeds are not available on all cycles�

Figure 16

DISPLAY (FOR MCSFLW27W ONLY)

d e f g

a� Cycle Indicator: Indicates stage of wash/dry cycle�

•

: Prewash • : Wash • : Rinse • : Spin

•

: Time Save

b� Clock: Indicates time left until the end of wash/dry cycle�

c� Feature Indicator: Indicates features that are active�

•

Sound: Indicates that sounds are on� When unlit, unit is muted�

•

Door Lock: Machine is locked for duration of cycle�

•

Child Lock: Child lock is on�

•

Add a Garment

d� Water Temperature: Indicates the selected temperature�

e� Spin Speed: Indicates the selected spin speed�

f� Soil Level Indicator: Indicates the selected soil level�

g� Additional Functions: Indicates additional functions selected�

•

Extra Rinse •

Easy Iron •

Prewash

Press 3 sec. to set My Cycle

h� Soil: Press [Soil] to increase time for heavier soiled items�

• There are three (3) soil levels options�

• Each bar increases the base wash time by 15 minutes�

i� Function: Use to select functions during the wash cycle

j� Child Lock: Press [Delay] and [Temp] at the same time for 3 seconds to Unlock/Lock the control panel�

• On/Off Button will still function�

k� My Cycle: After a wash cycle is modified, hold down [Spin] to save your settings�

• You can quickly choose this cycle for your next wash by turning the dial to My Cycle�

• Override saved settings by holding the [Spin] button down again after a different cycle and options are

selected�

l� Sound: Press the [Soil] button for 3sec� to turn the sound on or off�

WASH CYCLE PARAMETERS

WASH CYCLE PARAMETERS (FOR MCSCWD27W5 ONLY)

NOTE: Maximum drying load size is smaller than wash load size�

Program

Max� Washing/Drying

Load in lbs (kgs)

Temp

Default

Time (H:M)

Time

Save

Extra

Rinse

Delay

Soil

Level

Spin

Speed

Normal/Cotton

26�4/17�6

(12�0/8�0)

Warm 1:04

- - Med

Perm Press 13�2 (6�0) Warm 1:35

Light Low

Heavy Duty

26�4/17�6

(12�0/8�0)

Hot 2:36

- Med

Bulky/Large 13�2 (6�0) Warm 2:18

Light Med

Sports Wear 13�2 (6�0) Warm 2:08 Light Med

Spin Only 26�4 (12�0) - 0:12 - - - High

Rinse & Spin 26�4 (12�0) - 0:20 - - High

Tub Clean - Hot + 1:58 - - - -

Timed Dry

1�1/2�2/5�5

(0�5/1�0/2�5)

- 1:28 - - - Highest

Auto Dry

17�6 (8�0) - 4:18 - -

- Highest

Sanitary 13�2 (6�0) Hot 3:09 -

- Med

Baby Wear 26�4 (12�0) Eco 1:39 - Light Med

Wool 4�4 (2�0) Warm 1:37 - - Low

Delicates 5�5 (2�5) Eco 1:00 - - Low

Quick Wash 4�4 (2�0) Cold 0:20 - - - Med

NOTE:

is Optional Function�

NOTE:

is Dry function�

WASH CYCLE PARAMETERS (FOR MCSFLW27W ONLY)

Program

Max� Wash Load

in lbs (kgs)

Temp

Default

Time (H:M)

Spin

Speed

Time

Save

Extra

Rinse

Easy

Iron

Pre-

wash

Delay

Normal/Cotton 26�5 (12�0) Warm 1:04 Med

Perm Press 13�2 (6�0) Warm 1:35 Low -

Heavy Duty 26�5 (12�0) Hot 2:36 Med

Bulky/Large 13�2 (6�0) Warm 2:18 Med

Sport Wear 13�2 (6�0) Warm 2:08 Med

Spin Only 26�5 (12�0) - 0:12 High - - -

Drain Only 26�5 (12�0) - 0:01 - - - - -

Rinse & Spin 26�5 (12�0) - 0:20 High - -

Tub Clean - Hot 1:58 - - - - -

Cold Wash 26�5 (12�0) Cold 1:42 Med

Sanitary 13�2 (6�0) Hot 3:09 Med -

Baby Wear 26�5 (12�0) Eco 1:39 Med

Wool 4�4 (2�0) Warm 1:37 Low - -

Delicates 5�5 (2�5) Eco 1:00 Low - - - -

Quick Wash 4�4 (2�0) Cold 0:20 Med - - - -

NOTE:

is Optional Function�

NOTE: is Required Function�

NOTE: ENERGY TEST PROGRAM - NORMAL/COTTON

“Normal/Cotton” is the standard washing program to which the information in the label and energy guide relates,

and is suitable to clean normally soiled cotton laundry and is the most efficient program in terms of combined

energy and water consumptions for washing that type of laundry� The actual water temperature may differ from

the declared cycle temperature�

NOTE: The parameters in this table are only for user’s reference� The actual parameters maybe vary from the

parameters in above table�

POWER LOSS MEMORY FUNCTION

In the event of the loss of power, the washer will automatically resume operation from previous settings when

power is restored�

CARE AND MAINTENANCE

Before doing any maintenance, be sure to remove the power plug from the outlet and close the tap�

WARNING:

• DO NOT use solvents to clean the unit� The washing machine can be damaged, or toxic gasses may be

produced�

• NEVER spray water on the washing machine to clean it�

• DO NOT use detergents that contain PCMX to clean the washing machine�

• Certain internal parts are intentionally not grounded and may present a risk of electric shock only during

servicing� Service Personnel – DO NOT contact the following parts while the appliance is energized: Drain

Pump, Door Lock, Drying Heater (Combo), Fan Motor (Combo)�

CLEANING AND MAINTENANCE OF WASHING MACHINE CABINET

Proper maintenance on the washing machine can extend its working life� The surface can be cleaned with

diluted non-abrasive neutral detergents when necessary� If there is any water overflow, use a cloth to wipe it off

immediately� DO NOT allow sharp items to strike the cabinet�

NOTE: DO NOT use formic acid and its diluted solvents or equivalent�

CLEANING THE INTERNAL DRUM

Any rust left inside the drum by the metal articles should be cleaned out immediately with chlorine-free detergents�

DO NOT use steel wool�

CLEAN DETERGENT BOX

1� Open Detergent box�

2� Press down the arrow and slide out assembly� (Figure 17-1)

3� Lift the clip and remove softener cover and wash all sections with water� (Figure 17-2)

4� Replace the softener cover and push the drawer back into position� (Figure 17-3)

Figure 17

Figure 17-1 Figure 17-2 Figure 17-3

CLEAN INLET FILTER

Inlet filter maybe need to be cleaned if there is insufficient or no water in when the tap is opened�

To clean the filter:

1� Close the tap�

2� Select any procedure except “Wash” or “Drain” procedure�

3� Press the button “Start/Pause” and keep the procedure running for about 40 seconds�

4� Remove the inlet pipe from the tap�

5� Wash the filter with water

6� Reconnect the inlet pipe�

WASHING THE FILTER IN WASHING MACHINE

1� Remove the inlet pipe from the rear of the machine�

2� Pull out the filter with needle nose pliers rinse with water�

3� Put the filter back into place�

4� Reconnect the inlet pipe�

5� Open the tap and make sure there is no water leakage�

6� Close the tap�

REMOVING FOREIGN ITEMS FROM DRAIN PUMP FILTER

The drain pump filter can filter small foreign matters from clothing being washed� Clean the filter periodically to

ensure the normal operation of washing machine�

Figure 18

The pump should be inspected if the machine

does not empty and/or spin, or if it makes unusual

noises during draining due to objects (such as,

coins etc�) blocking the pump�

To access and clean the filter:

1� Open the lower access cover� (Figure 19)

2� Remove the emergency drain hose cap and

let water drain out� It is recommended to

have a vessel ready to catch remaining water�

(Figure 20)

3� Replace emergency drain hose, and open

the filter by turning counter-clockwise�

(Figure 21)

4� Remove any objects in filter and replace,

locking in by turning clockwise� (Figure 22)

Figure 20

Figure 22

Figure 19

Figure 21

THAW A FROZEN WASHING MACHINE

If the temperature drops below zero and your washing machine gets frozen, you may:

1� Disconnect the power supply for the washing machine�

2� Wash the tap connection with warm water to loosen inlet pipe�

Emergency

Drain Hose

WARNING: To avoid burning, it shall be done after the hot water inside the machine cools down�

WARNING: When the appliance is in use and depending on the program selected there may be hot water in the

pump� Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle,

and is empty� When replacing the cover, ensure it is securely in place�

3� Remove the inlet pipe and immerse it in warm water�

4� Pour warm water into washing drum and wait for 10 minutes�

5� Reconnect inlet pipe to the tap and check whether inlet and outlet are working normally�

NOTE: when the washing machine is reused, make sure the ambient temperature is above 32 °F (0 °C)�

TO PREVENT FREEZING

If your washing machine is located in the room where it can get frozen easily, please drain the remaining water

inside drain pipe and inlet pipe thoroughly�

Remove the remaining water in inlet pipe:

1� Close the tap�

2� Screw off the inlet pipe from tap and put its end into the

container�

3� Start up any procedure except single Wash or Drain

procedure� Water will be drained out of inlet pipe if any

for about 40 seconds�

4� Reconnect the inlet pipe to tap�

EMERGENCY DOOR RELEASE

In the case of a power failure or other circumstances and door

cannot be opened, if it is necessary to open the door, pull down

on the cord inside the access panel� Be sure to restore the pull

cord after opening the door�

CAUTION: The emergency switch pull cord cannot be used

during washing� If unit is in operation, wait for it to stop and for

the interior to cool to a safe temperature before opening door�

Figure 23

Emergency

Door

Pull Cord

TROUBLESHOOTING

ALARM CODE DETECTION

Alarm Code Cause of Problem Solution

E30 Door is not properly closed�

Check if clothes are stuck in door�

Close door and restart�

E10 Problem with water flow�

Check if the water pressure is too low�

Make sure inlet hose is not bent or blocked�

Check if the inlet valve filter is blocked�

E21 Water taking too long to drain� Check if the drain hose is blocked�

E12 Water overflow� Restart the washer�

EXX Other Restart machine to clear� Call customer service if code persists�

NOTE: After trying the solution, restart the washing machine� If code persists, contact customer service�

When the washing machine needs servicing, please contact our customer service department, and a representative

will try to diagnose the issue� Please do not dismantle the washing machine without prior permission� Doing so

will void your warranty�

If the washing machine fails to operate properly, or it sounds an alarm, please check the following guidelines for

possible solutions to common problems or alarm indicators�

LIST OF PROBLEMS AND POSSIBLE SOLUTIONS

Problem Cause Solution

Washing machine

will not start �

Check if the door is closed tightly�

Check if power plug is properly inserted�

Check if water supply is open�

Check if “On/Off” button is pressed�

Check if “Start/Pause” button is pressed�

Door cannot be opened� Safety lock is engaged� Disconnect the power�

Heating fault

NTC thermistor is damaged and

heating pipe is worn�

Contact customer service�

Water leakage

The connection between inlet

pipe or outlet hose and tap or

washing machine is not tight�

Check and fasten water pipes�

Drain pipe is blocked� Clean up outlet hose and drain�

Water overflowing from

the bottom of the

Machine

The inlet pipe is not connected

firmly�

Fix the inlet pipe�

Outlet hose has water leakage� Replace the drain hose�

Indicator or display do

not light�

Power is disconnected� Check if plug is connected correctly and power is on�

PC board has problems�

Contact customer service�

Harness has connection problem�

Detergent residue in the

detergent box

Washing powder is damp and

hardened�

Clean and wipe the box�

Use liquid detergents or the detergents special for hi

efficiency front load washer�

Clothes not clean

enough

The clothes are too dirty� Select a proper washing program�

Insufficient detergent quantity

Make sure to follow instructions for adding detergent

amount�

Abnormal noises or

vibration

Make sure the transport bolts are removed�

Make sure cabinet is installed on solid, level surface�

Check for any foreign items in the unit�

Make sure leveling legs are level�

LIMITED WARRANTY

MC Appliance Corporation warrants each new Washer and Combo Washer/Dryer to be free from defects in material and work-

manship, and agrees to remedy any such defect or to furnish a new part(s), at the company’s option, for any part(s) of the unit

that has failed during the warranty period� Parts and labor expenses are covered on this unit for a period of one year from the

date of purchase� A copy of the dated sales receipt/invoice is required to receive warranty service, replacement or refund�

This warranty covers appliances in use within the contiguous United States, Alaska, Hawaii and Puerto Rico� This warranty does not

cover the following:

• Damages due to shipping damage or improper installation�

• Damages due to misuse or abuse�

• Content losses due to failure of the unit�

• Inside components such as filters, etc�

• Repairs performed by unauthorized service agents�

• Service calls that do not involve defects in material and workmanship such as instructions on proper use of the product

or improper installation�

• Replacement or resetting of house fuses or circuit breakers�

• Failure of this product if used for other purposes than its intended purpose�

• Disposal costs for any failed unit not returned to our factory�

• Any delivery/installation costs incurred as the result of a unit that fails to perform as specified�

• Expenses for travel and transportation for product service if your appliance is located in a remote area where service by

an authorized service technician is not available�

• The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accord-

ance with published installation instructions� Service may not be available on units installed in nontraditional housing

locations (ie� boats, etc�)

• Refunds for non repairable products are limited to the price paid for the unit per the sales receipt�

• This warranty is non transferable� This warranty applies only to the original purchaser and does not extend to any

subsequent owner(s)�

Limitations of Remedies and Exclusions:

Product repair in accordance with the terms herein, is your sole and exclusive remedy under this limited warranty� Any and all

implied warranties including merchantability and fitness for a particular purpose are hereby limited to one year or the shortest

period allowed by law� MC Appliance Corporation is not liable for incidental or consequential damages and no representative or

person is authorized to assume for us any other liability in connection with the sale of this product� Under no circumstances is the

consumer permitted to return this unit to the factory without the prior written consent of MC Appliance Corporation�

Some states prohibit the exclusion or limitation of incidental or consequential damages, or limitations on implied warranties�

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state�

Model Parts Labor Type of Service

MCSCWD27W5

One Year One Year In Home

MCSFLW27W

For Service or Assistance please call 888-775-0202 or visit us on the web at www.mcappliance.com to request warranty service

or order parts�

Magic Chef® logo is a registered trademark of CNA International, Inc.

www.mcappliance.com Printed in China

LEA ESTE MANUAL ANTES DE UTILIZAR SU LAVADORA Y SECADORA Y

GUÁRDELO PARA FUTURA REFERENCIA.

Model MCSCWD27W5 / MCSFLW27W

Combo de Lavadora y Secadora de 24”

Lavadora de carga frontal de 24”

Manual del usuario

REGISTRACIÓN DEL PRODUCTO

Gracias por comprar el producto Magic Chef®� El primer paso para proteger su nuevo producto es completar la forma de registración

en nuestra pagina web: www�mcappliance�com/register� Los beneficios de registrar su producto incluyen lo siguiente:

1� Al registrar su producto nos permite contactarle para notificarle de un cambio de seguridad o actualización del

producto�

2� Si llegara a necesitar servicio bajo garantía, registrando su producto nos permite ser más eficiente en procesar el

servicio�

3� En el evento que usted tenga una perdida que esta cubierto por un seguro, registrando su producto puede servir

como prueba de su compra�

Una vez más gracias por comprar un producto marca Magic Chef®�

ÍNDICE

REGISTRACIÓN DEL PRODUCTO � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 27

INSTRUCCIONES DE SEGURIDAD IMPORTANTES �� 29

ESPECIFICACIONES �� 32

INSTRUCCIONES DE INSTALACIÓN ��33

ANTES DE USAR� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 36

INSTRUCCIONES DE FUNCIONAMIENTO� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 37

PARÁMETROS DE CICLOS DE LAVADO �� 44

CUIDADO Y MANTENIMIENTO ��46

SOLUCIÓN DE PROBLEMAS� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 49

GARANTÍA LIMITADA �� 51

INSTRUCCIONES DE SEGURIDAD IMPORTANTES

Este manual contiene Instrucciones de seguridad, Instrucciones de instalación y operación, y Consejos para

solucionar problemas� Por favor, léalo cuidadosamente antes de utilizar la lavadora para conocer las instrucciones

sobre cómo utilizar y mantener el producto adecuadamente� Asegúrese de seguir las instrucciones de seguridad

para evitar lesiones o daños al producto�

Guarde este manual� Al transferir o vender el aparato a un tercero, el manual debe entregarse junto con el

aparato�

Antes de contactar a servicio técnico, cerciórese de que el equipo haya sido instalado y se esté usando de manera

correcta, y lea la sección de solución de problemas�

ADVERTENCIA: Siga las precauciones que se indican a continuación al utilizar el aparato�

NOTA: Las especificaciones pueden cambiar en cualquier momento sin aviso previo�

Advertencias según la Propuesta 65 del Estado de California

ADVERTENCIA: La Ley de Ejecución sobre Materiales Tóxicos y Agua Potable Segura de California establece

que el gobernador de California deberá publicar una lista de sustancias sobre las que el Estado de California

tenga información de que producen cáncer, defectos congénitos y otros daños reproductivos, y establece que

los comercios deberán advertir sobre las posibles exposiciones a tales sustancias� Este producto contiene una

sustancia química que el Estado de California sabe que produce cáncer, defectos congénitos y otros daños

reproductivos� Este aparato puede ocasionar bajos niveles de exposición a algunas de las sustancias que se

encuentran en la lista, incluidos benceno, formaldehído y monóxido de carbono�

1� Lea todas las instrucciones antes de utilizar este producto�

2� Este aparato es solo para uso doméstico� No está diseñado para aplicaciones comerciales�

3� Este aparato está diseñado solamente para uso en interiores� NO lo utilice al aire libre�

4� NO use este electrodoméstico de una manera que no sea la prevista�

5� Use solo los detergentes o suavizantes recomendados en este manual y manténgalos fuera del alcance de

los niños�

6� Esta máquina no es para ser usada por personas (incluidos los niños) con capacidad física, psíquica o

sensorial reducida o falta de experiencia y conocimiento, a menos que hayan recibido supervisión o

instrucción relativa al uso de la lavadora por parte de una persona responsable por su seguridad�

7� Este aparato debe instalarse correctamente, conforme a las instrucciones de instalación, antes de usarse�

8� NO desenchufe su aparato halando el cable de alimentación� Siempre sujete la clavija firmemente y sáquela

derecha desde el tomacorriente�

9� No utilice ningún aparato que tenga un cable o enchufe dañado, si está dañado o funciona mal de algún

modo o si el tomacorriente no funciona correctamente� Comuníquese con el servicio al cliente o con un

técnico de servicio�

10� SIEMPRE apague y desenchufe el equipo del tomacorriente antes de repararlo, cambiarle accesorios o

limpiarlo� Deje enfriar por completo el equipo antes de limpiarlo, moverlo o hacerle servicio� Apagar el

equipo no lo desconecta de la fuente de poder�

11� NO coloque nada inflamable o explosivo dentro, sobre o cerca del aparato� NO lave prendas de ropa ni

artículos empapados con químicos inflamables o explosivos� Para reducir el riesgo de incendio, no deberán

colocarse en la lavadora ropa, trapos de limpieza, cabezales de mapos o elementos similares que tengan

restos de cualquier sustancia inflamable, por ejemplo aceite de cocina, aceites derivados del petróleo o

destilados, ceras, grasas, etc� Estos artículos pueden contener sustancias inflamables que, incluso después

del lavado, pueden crear humo o incendiarse� NO seque artículos que contengan goma de espuma o

materiales con textura similar a la goma�

12� SIEMPRE espere que el tambor la lavadora se detenga por completo completamente antes de meter la

mano para colocar o sacar prendas�

13� La puerta de carga debe estar cerrada mientras el tambor esté centrifugando�

14� NO utilice esta lavadora a menos que todos los paneles de cierre estén instalados correctamente�

15� NO manipule ni modifique los controles�

16�

ADVERTENCIA: Existe el riesgo de que un niño quede atrapado� NO permita que los niños jueguen

encima o dentro del aparato� Es necesario vigilar de cerca a los niños cuando se utilice el aparato cerca de

ellos�

17� Este electrodoméstico debe enchufarse en un tomacorriente adecuadamente instalado y conectado a

tierra, que cumpla con los requisitos de voltaje indicados en la etiqueta de especificaciones eléctricas�

18�

PRECAUCIÓN: El cable eléctrico está equipado con un enchufe de 3 puntas conectado a tierra para

protegerlo de peligros de descarga eléctrica� SIEMPRE conecte el cable a un receptor de pared a tierra de

tres espigas instalado correctamente y NO elimine la espiga a tierra�

19� Bajo ciertas circunstancias, se podría producir gas de hidrógeno en un sistema de agua caliente para el hogar

que no se haya usado por dos semanas o más� El gas de hidrógeno es altamente explosivo� Si el sistema de

agua caliente no se ha usado por más de dos semanas, abra todos los grifos de agua caliente y deje que

salga el agua por varios minutos antes de usar la lavadora compacta�

20� NO altere ni repare el equipo usted mismo� De ser necesario, comuníquese con el servicio al cliente o con

un técnico de servicio calificado�

21� Para reducir el riesgo de descarga eléctrica o incendio, no use un prolongador ni un adaptador de

tomacorriente para conectar el equipo a una fuente de energía eléctrica� El aparato debe estar conectado a

tierra correctamente usando un tomacorriente de pared de tres puntas�

22� NO instale la lavadora en un área húmeda o mojada, o donde pueda mojarse o esté expuesta a las

condiciones meteorológicas externas� NO la limpie utilizando atomizadores de agua�

23� NO siente niños en la parte superior ni permita que niños o mascotas se suban a la lavadora� Revise SIEMPRE

el interior antes de usarla�

24� La puerta de vidrio podría estar muy caliente durante la operación� Mantenga a los niños y mascotas

alejados de la lavadora mientras esté en uso�

25� Limpie regularmente el enchufe para eliminar polvo y sucio y así evitar fallas eléctricas�

26� Se recomienda desconectar el equipo cuando no esté en uso�

27� SIEMPRE asegúrese de conectar de forma correcta y segura el cable eléctrico al tomacorriente y las

mangueras de agua para evitar fugas o descarga eléctrica�

28� NO opere el equipo, ni manipule el enchufe con las manos húmedas�

29� La temperatura del agua de la lavadora no debería exceder los 131 °F (55 °C)�

30� NO lave impermeables, abrigos gruesos ni artículos pesados similares�

31� NO lave a máquina materiales de fibra de vidrio (como cortinas y decoraciones para ventanas que

contengan materiales de fibra de vidrio)� Pequeñas partículas podrían permanecer en la lavadora y pegarse a

las telas en las tandas siguientes, lo que puede causar irritación de la piel�

32� Cuando vaya a desechar el aparato o ponerlo fuera de servicio, asegúrese de quitar la puerta de el equipo y

cortar el cable de alimentación�

33� NO introduzca las manos en el tambor de lavado si el agitador se está moviendo�

34� PRECAUCIÓN: El contenido puede estar CALIENTE cuando el ciclo de lavado y/o secado haya terminado�

LEA ESTA INFORMACIÓN DE SEGURIDAD

Y SÍGALA CUIDADOSAMENTE

GUARDE ESTAS INSTRUCCIONES

ESPECIFICACIONES

Altura 33�5” (850 mm)

Anchura 23�5” (595 mm)

Profundidad 23�5” (595 mm)

Profundidad con puerta abierta 42�5” (1080 mm)

Peso 160�9 lbs� (73�0 kg)

Tensión/Frecuencia en c�a� 120V~60Hz

Corriente nominal 11�0A

Máx� capacidad de lavado 26�4 lbs� (12�0 kg)

Máx� capacidad de secado (solamente para MCSCWD27W5) 17�6 lbs� (8�0 kg)

Tamaño del tambor 2�7 pies cúbicos

Figura 1

33�5”

(850 mm)

23�5” (595 mm)

42�5” (1080 mm)

INSTRUCCIONES DE INSTALACIÓN

1� La lavadora debe estar adecuadamente conectada a tierra� En el caso de corto circuito, la conexión a tierra

puede reducir el peligro de descarga eléctrica�

2� La lavadora deberá ser operada en un circuito separado de otros aparatos eléctricos�

PIEZAS INCLUIDAS

Antes de iniciar la instalación, corroborar que el paquete que

se encuentra dentro del tambor contiene todas las piezas

incluidas�

REQUISITOS DE INSTALACIÓN

REQUISITOS ELÉCTRICOS

1� Se requiere un suministro eléctrico de 120 v, 60 Hz, c�a� de 15 o 20 amp, con fusible� Se debería usar un fusible

con retardo de tiempo o un circuito que solo sirva a este aparato�

2� Esta lavadora viene con un cable de alimentación con enchufe de conexión a tierra de tres puntas�

3� Para minimizar posibles peligros de descarga, el cable deberá estar enchufado dentro de un tomacorriente de

tres puntas, adecuadamente conectado a tierra y de acuerdo con la codificación y ordenanzas locales� Si no

se dispone de un tomacorriente adecuado, es responsabilidad del cliente hacer que un electricista calificado

instale un tomacorriente adecuadamente conectado a tierra�

4� Si los códigos permiten y se utiliza un cable a tierra separado, se recomienda que un electricista calificado

determine si la descarga a tierra es adecuada�

5� NO HACER MASA en una tubería de gas�

6� Verifique con un técnico calificado si usted no está seguro si la lavadora está correctamente conectada a tierra�

7� NO COLOCAR un fusible en el circuito neutro o en el circuito de puesta a tierra�

8� Ciertas partes internas no han sido puestas a tierra intencionalmente y podrían presentar el riesgo de

descarga eléctrica solamente durante el servicio técnico� Personal de servicio técnico: no toque las siguientes

piezas mientras el aparato está energizado: Bomba de desagüe, bloqueo de la puerta, calentador de secado

(combo), motor del ventilador (combo)�

REQUISITOS DE UBICACIÓN

El seleccionar la ubicación correcta de la lavadora mejora el rendimiento, reduce el ruido al mínimo y evita su

desplazamiento involuntario� La lavadora puede ser instalada bajo una mesada personalizada, en un sótano,

lavadero, armario empotrado o en área con un hueco�

Usted necesitará:

• Un calentador de agua fijado a 120° F (49° C)�

• Un tomacorriente eléctrico con toma a tierra situado a menos de 6 pies (1,8 m) del lugar donde el cable de

alimentación está acoplado a la parte posterior de la lavadora�

• Grifos de agua fría y caliente situados dentro de 4 pies (1,2 m) de las válvulas de llenado de agua caliente y

fría, con una presión de agua de 20 - 100 psi (137,9 - 689,6 kPa)�

• Un suelo plano con una pendiente máxima de 1” (25 mm) debajo de la lavadora� No se recomienda la

instalación de la lavadora en superficies de suelo blando, como alfombras ni superficies con refuerzo de

espuma�

Mangueras de

agua (2)

Conexión de

cable

Tapones del

orificio de

transporte (4)

Figura 2

• Un piso sólido y resistente para soportar la lavadora, cuyo peso total (agua y tanda) es de 200 lb (90 kg)�

• No utilice la lavadora a temperaturas inferiores a 32 °F (0 °C)� Podría quedar algo de agua en la lavadora,

ocasionándole daños en bajas temperaturas�

• La ubicación debe ser lo suficientemente grande para permitir que la puerta de la lavadora abra

completamente� La puerta se abre más de 90° y no es reversible�

• Debe considerarse espacio adicional para una mayor facilidad de instalación y mantenimiento�

• Se recomienda espacio mínimo de 1” (25 mm) en todos los lados de la lavadora para reducir la transferencia

de ruido�

• Pueden ser necesarios espacios libres adicionales para pared, puerta y molduras de piso�

• También debe considerarse el espacio para los aparatos acompañantes�

Figura 3

Figura 4

INSTALACIÓN

PRECAUCIÓN: Los materiales de embalaje pueden ser peligrosos

para los niños� Disponga de ellos correctamente y NO DEJE que los

niños jueguen con ninguno de los materiales de embalaje�

Antes de utilizar esta lavadora, deben retirarse los pernos de

transporte de la parte posterior de la máquina� Realice los

siguientes pasos para quitar los pernos:

1� Afloje todos los pernos y, a continuación, quítelos�

2� Inserte los tapones de los orificios de transporte dentro de

los orificios�

3� Conserve los pernos de transporte para uso futuro�

Asegúrese de quitar el pequeño triángulo de espuma junto con la

pieza de espuma en el fondo� En caso contrario, coloque con cuidado

el equipo hacia abajo y quítelo� Al desembalar la lavadora, verifique

que no haya piezas faltantes o dañadas� Si faltara algún elemento,

comuníquese con el servicio al cliente�

LEVELING THE WASHER

1� When positioning the washing machine, make sure the

legs are screwed in close to the cabinet� If not, turn them

to their original positions by hand or with a wrench and

tighten the nuts with a wrench�

2� After positioning the washing machine, push on all four

corners at the top of washing machine� If the washing

machine has any wobble, or is not stable when being

pressed, adjust the leg to level the machine�

3� To level the unit, loosen the lock nut with a wrench and

turn the leg by hand until it tightly contacts with the floor�

Press the leg with one hand and tighten the locking nut

close to the cabinet with the other hand�

4� Repeat steps 2 and 3 as needed�

5� Use a bubble level to check front to back, side to side, and

corner to opposite corner to ensure the washing machine

is level� Repeat above steps if needed�

Figura 5

Figura 6

SISTEMA DE DESAGÜE

SISTEMA DE DESAGÜE VERTICAL

- PARED O SUELO

2” (5 cm)

Figura 7 Figura 8

El desagüe vertical requiere una

tubería vertical con diámetro mínimo

de 2” (5 mm)� La capacidad mínima

de transporte no puede ser menor a

17 galones (64 l) por minuto� La parte

superior de la tubería vertical debe

ser de al menos 24” (60 cm) de altura

y no más de 39” (100 cm) desde la

parte inferior de la lavadora�

INSTALACIÓN DE MANGUERA DE

ENTRADA DE AGUA INSTALACIÓN DE

MANGUERA DE ENTRADA DE AGUA

Conecte el extremo de la manguera de admisión de agua

con el codo de 90° a la parte posterior de la lavadora y

gire en sentido de las agujas del reloj para ajustar� Note la

posición de las tomas de entrada de agua fría y caliente�

Conecte el otro extremo de la manguera de entrada de

agua al grifo de agua fría o caliente correspondiente�

Ajuste girando en sentido de las agujas del reloj y accione

la válvula de agua para verificar si hay pérdida de agua�

Si encuentra alguna pérdida, verifique que las conex-

iones estén apretadas y que haya arandelas; repita el

procedimiento�

SISTEMA DE DESAGÜE DEL TAMBOR DE LAVADO

El tambor de lavado necesita una capacidad mínima de

20 galones (76 l)� La parte superior del tambor de lavado

debe estar al menos a 60 cm por encima del suelo�

SISTEMA DE DESAGÜE DE PISO

El sistema de desagüe de piso requiere un

interruptor de efecto sifón que puede adquirirse

por separado� El interruptor de efecto sifón debe

estar a un

mínimo de

28” (71 mm)

de la parte

inferior de la

lavadora�

Podrían ser

necesarias

mangueras

adicionales�

Figura 9 Figura 10

min� 24”

(61 cm)

max� 39”

(100 cm)

min� 24”

(60 cm)

max� 39”

(100 cm)

min� 28”

(71 cm)

Figura 11

Figura 12

Caliente

El conector a la toma de agua es un

codo a 90°�

Frío

ANTES DE USAR

LISTA DE VERIFICACIÓN Y PREPARACIÓN ANTES DE LAVAR

Lea cuidadosamente todas las instrucciones para evitar cualquier daño o problemas con la lavadora y la ropa�

SIEMPRE siga las instrucciones en las etiquetas sobre cuidado de la tela en prendas de ropa para un cuidado adecuado�

ADVERTENCIA: NO deje las piezas lavadas en la lavadora por largos ratos� Las piezas que se dejan en la lavadora

pueden ponerse mohosas y mancharse� La ropa también puede decolorarse si no se lava siguiendo la temperatura

de lavado indicada y las instrucciones�

SELECCIÓN DEL DETERGENTE

• Se recomienda usar detergente en polvo de baja espuma�

• Algunos detergentes podrían no disolverse por completo si hay mucha cantidad o si la temperatura del agua

es muy baja�

• El cloro puede dañar la ropa� Utilice cloro con cuidado y sigas las instrucciones del detergente y cuidado de

la vestimenta�

El método de lavado se basa en el peso de la ropa, nivel de suciedad, dureza del agua y recomendaciones del

fabricante del detergente�

NOTA: NO coloque ni guarde productos de lavandería, tales como detergentes, cloro o suavizante líquido, en la parte

superior de la lavadora/secadora� Limpie cualquier derrame de inmediato� Estos productos pueden dañar el acabado y

los controles� Mantenga los productos de lavandería en un espacio seguro y seco fuera del alcance de los niños�

SEPARE LA ROPA A LAVAR

Clasifique la ropa que va a lavar en algodón, fibra mixta, fibra sintética, seda, lana, etc� La ropa clara y oscura

también debería separarse�

NOTA: La tela nueva de color debe lavarse aparte�

• Accesorios: Los accesorios sueltos de algunas prendas pueden dañarse o dañar la lavadora� La ropa que

contenga botones o bordados debería voltearse antes de lavarla�

• Cierres: Las cremalleras deben cerrarse y los botones o ganchos deben estar firmemente fijados� Cualquier

cinta o lazo suelto debe amarrarse antes de lavarse�

• Materiales a prueba de agua: No se recomienda lavar telas impermeables ya que pueden dañarse o causar

daños a la lavadora y otras piezas que se estén lavando�

QUITAR TODOS LOS OBJETOS SUELTOS DE LA ROPA

Revise todos los bolsillos/compartimientos de la ropa a lavar y retire cualquier artículo suelto como monedas� Los

elementos sueltos podrían dañar la lavadora�

EQUILIBRAR LA CARGA

Lavar una prenda grande y pesada, como toallas, jeans, chaquetas, etc�, puede causar una carga desequilibrada� Se

sugiere añadir uno o dos artículos más para equilibrar la carga y permitir un desagüe suave y completo�

INSTRUCCIONES DE FUNCIONAMIENTO

PANEL DE CONTROL (SOLAMENTE PARA MCSCWD27W5)

a� Encendido/Apagado: Presione [On/Off] para ENCENDER el equipo� Vuelva a presionar ese botón para

APAGAR el equipo�

NOTA: Si la lavadora está programada para un ciclo de lavado y no se la hace arrancar dentro de los 10

minutos, el ciclo se cancelará y el equipo se apagará automáticamente�

b� Inicio/Pausa: Presione [Start/Pause] para iniciar un ciclo de lavado� Presione [Start/Pause] otra vez para hacer

una pausa en el ciclo cuando la lavadora está en marcha� Vuelva a presionar [Start/Pause] para reanudar el

ciclo� Para añadir una prenda una vez comenzado el ciclo de lavado, presione este botón durante 3 segundos

antes de que el tambor se haya llenado de agua� Esto solo se puede hacer al comienzo del ciclo, antes de

que el agua llegue al fondo de la puerta� Espere que el tambor se detenga y la puerta se desbloquee, luego

agregue las prendas� Cierre la puerta y presione [Start/Pause] para seguir lavando�

c� Ciclos de lavado

1� Mi ciclo: Seleccione esta opción para guardar como predeterminado un programa de lavado que utilice

frecuentemente�

• Para programarlo, seleccione las configuraciones que desee utilizar y mantenga presionado [Spin]

durante 3 segundos para guardarlo�

2� Lavado rápido: Seleccione esta opción para lavar pequeñas cargas de prendas no muy sucias�

3� Ropa delicada Seleccione esta opción para telas delicadas como camisas de vestir, nailon, etc�

• El ciclo de lavado funciona a una temperatura más baja�

4� Lana: Esta opción sólo se utiliza para lavar prendas de lana etiquetadas como “Lavable a máquina”�

• Para los tejidos de lana se deberán seleccionar el detergente y la temperatura del agua

apropiadas�

• Velocidad de centrifugado menor y menos agitación

5� Prendas de bebé: Para lavar ropa de bebé�

6� Sanitario: Utiliza agua caliente para que las enzimas del detergente actúen con más eficacia sobre

piezas difíciles de lavar o muy sucias�

Figura 13

Press 3 sec. to set My Cycle

e f

l m n

h i j d c b

7� Normal/Algodón: Seleccione esta opción para prendas de algodón y telas que utiliza regularmente�

• Ciclo de lavado extendido con mayor intensidad

• Se recomendada para telas: algodón, ropa de cama, sábanas, camisetas, toallas, pantalones

vaqueros, etc�

• Se puede añadir el ciclo de secado�

8� Planchado permanente: Ciclo de lavado de fuerza moderada� Se usa para reducir las arrugas en la ropa

durante el lavado�

9� Lavado intenso: Seleccione esta opción para prendas grandes y pesadas�

• Se puede añadir el ciclo de secado�

10� Voluminosos/grandes: Seleccione esta opción para artículos voluminosos y grandes�

• Ciclo de lavado extendido

11� Ropa deportiva: Seleccione esta opción para ropa deportiva�

• Este ciclo de lavado limpia las prendas muy sucias�

12� Solo centrifugado: Seleccione esta opción para centrifugar una tanda por separado de un ciclo de

lavado normal�

• El agua con detergente o el agua de enjuague debe ser desagotada antes del centrifugado�

13� Enjuague y centrifugado: Seleccione esta opción para enjuagar y centrifugar una tanda por separado de

un ciclo de lavado normal�

• Esto puede ser útil para prevenir que manchas frescas se impregnen a las telas�

14� Limpieza del tambor: Seleccione esta opción para limpiar el tambor de lavado� Este programa utiliza

elevadas temperaturas para esterilizar el tambor a la vez que elimina el detergente y los residuos

acumulados� Agregue cloro para una mejor limpieza� Este programa se debería utilizar por lo menos una

vez al mes con uso regular� NO AÑADIR ninguna prenda ni lavar nada durante este programa�

d� Ciclos de secado

NOTA: La carga de secado máxima es inferior al tamaño de la carga de lavado� Corrobore el tamaño de la

carga a secar cuando se lo utilice�

• Secado automático: Seleccione esta opción para pasar automáticamente al ciclo de secado según la

carga� El programa de Secado automático tiene un ciclo de centrifugado de 12 minutos y un ciclo de

aire de enfriamiento de 45 minutos� Se recomienda secar en varios lotes de menor tamaño para que el

desempeño sea mejor�

• Tiempo de secado: Seleccione esta opción para fijar manualmente la duración del ciclo de secado�

Los programas de Tiempo de secado incluyen un ciclo de centrifugado de 12 minutos y un ciclo de

aire de enfriamiento de 25 minutos� Se recomienda secar en varios lotes de menor tamaño para que el

desempeño sea mejor�

Tiempo en minutos Capacidad

58 1�8 lbs� (0�8 kg)

88 2�2 lbs� (1�0 kg)

199 6�6 lbs� (3�0 kg)

NOTA: Notas importantes para ciclos de secado

Para lavar solamente, es posible llenar el equipo hasta la máxima capacidad de lavado; sin embargo, las cargas

de tamaño inferior a la de la máxima capacidad de lavado pueden mejorar el desempeño y la eficacia�

En los ciclos de lavado más ciclo de secado, o los ciclos de secado solamente, no llenar unidad superando la

máxima capacidad de secado para permitir que la función de secado funcione de forma eficiente� Las cargas

de tamaño inferior a la capacidad máxima mejorarán el desempeño del equipo combinado�

NO cortar el suministro de agua ni quitar las conexiones de la manguera durante el ciclo de secado� Esta

es una unidad sin salida de aire que libere humedad durante el ciclo de secado� La secadora está equipada

con un bloqueo de seguridad de la puerta para garantizar temperaturas seguras y evitar quemaduras y otros

peligros de seguridad� La puerta quedará BLOQUEADA durante el ciclo de secado hasta que el equipo alcance

una temperatura segura� Una vez la temperatura sea segura, la puerta debe abrir y funcionar normalmente�

e� Ahorro de tiempo: Presione [Time Save] para disminuir el tiempo de lavado�

• Consulte la tabla Parámetros del ciclo de lavado para conocer los programas que pueden usar la

función Ahorro de tiempo�

f� Retraso: Presione [Delay] para fijar el tiempo de retraso en que debe comenzar el lavado�

• La luz del inicio con retraso parpadeará para indicar el tiempo de retraso� El tiempo de inicio del ciclo

puede ser retrasado entre 1 y 24 horas�

• Fije el programa de lavado, presione el botón Delay para fijar el número de horas que se retrasará el

ciclo de lavado, luego presione Start/Pause�

• Para cancelar el tiempo de retraso, presione el botón Delay hasta que la hora muestre 0H�

g� Temperatura: Presione [Temp�] para fijar la temperatura de lavado deseada�

• Presione el botón para fijar la temperatura de lavado (Caliente+, Caliente, Tibia, Eco, Fría)

h� Centrifugado: Presione [Spin] para aumentar la velocidad del centrifugado�

• El tambor de la lavadora centrifuga a una velocidad de hasta 1�300 rpm, lo que reduce el tiempo de

secado y ahorra energía�

• Presione el botón hasta que se encienda la velocidad deseada (Sin centrifugado, Velocidad baja, media,

alta, máxima)�

• Algunos tejidos (por ejemplo, prendas delicadas) requieren una velocidad de centrifugado menor�

• Las velocidades altas de centrifugado no están disponibles en todos los ciclos�

i� Suciedad: Presione [Soil] para aumentar el tiempo para artículos más sucios�

• Hay tres (3) opciones de nivel de suciedad�

• Cada barra aumenta el tiempo de lavado base por 15 minutos�

j� Nivel de secado: Presione el botón Secar continuamente para elegir el nivel de secado: Secado Extra/Secado

Normal/Secado Suave�

k� Bloqueo infantil: Presione [Delay] y [Temp�] al mismo tiempo durante 3 segundos para bloquear/desbloquear

el panel de control�

• El botón de encendido/apagado seguirá funcionando�

l� Enjuague adicional: Presione los botones [Temp�] y [Spin] al mismo tiempo para añadir un enjuague adicional

al ciclo seleccionado�

m� Mi ciclo: Después de modificar un ciclo de lavado, mantenga pulsado el botón [Spin] para guardar la

configuración�

• Se puede seleccionar rápidamente este ciclo para el siguiente lavado girando la perilla hacia Mi Ciclo�

• Anule la configuración guardada manteniendo pulsado el botón [Spin] nuevamente después de

seleccionar un ciclo y opciones diferentes�

n� Sonido: Presione el botón [Soil] durante 3 segundos para encender o apagar el sonido�

a� Indicador de ciclo: Indica la etapa del ciclo de lavado/secado�

•

: Prelavado • : Lavado • : Enjuague • : Centrifugado

•

: Ahorro de tiempo • : Enjuague adicional • : Secado

b� Reloj: Indica el tiempo restante para el final del ciclo de lavado/secado�

c� Indicador de funciones: Indica las funciones que están activas�

•

Sonido: Indica que los sonidos están activados� Cuando la luz está apagada, el equipo está con el

sonido en silencio�

•

Bloqueo de puerta: La máquina se bloquea por la duración del ciclo�

•

Bloqueo infantil: El bloqueo infantil está activado�

•

Añadir una prenda

d� Temperatura del agua: Indica la temperatura seleccionada�

e� Velocidad de centrifugado: Indica la velocidad de centrifugado seleccionada�

f� Indicador de nivel de suciedad: Indica el nivel de suciedad seleccionado�

g� Nivel de suciedad: Indica el nivel de secado seleccionado�

•

Secado adicional • Secado normal • Secado suave

NOTA: La carga de secado máxima es inferior al tamaño de la carga de lavado�

Figura 14

PANTALLA (SOLAMENTE PARA MCSCWD27W5)

ePress 3 sec. to set My Cycl

d e f g

PANEL DE CONTROL (SOLAMENTE PARA MCSFLW27W)

Figura 15