Yamaha 900SW Manual de usuario

Categoría
Amplificadores de audio
Tipo
Manual de usuario

Este manual también es adecuado para

Soavo-900SW
SUBWOOFER SYSTEM
UB
OWNER’S MANUAL
i En
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
IMPORTANT
Please record the serial number of this system in the
space below.
Model:
Serial No.:
The serial number is located on the rear of the main
unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Explanation of Graphical Symbols
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
Be sure to allow spaces of at least 20 cm above,
behind and on both sides of the unit.
Do not place the following objects on the unit:
A vessel with water in it.
If the vessel falls by vibrations and water spills, it
may cause damage to the unit, and/or you may get an
electric shock.
ii En
We Want You Listening For A
Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out
of your equipment by playing it at a safe level. One that
lets the sound come through loud and clear without
annoying blaring or distortion – and, most importantly,
without affecting your sensitive hearing.
Since hearing damage from loud
sounds is often undetectable until it is
too late, YAMAHA and the
Electronic Industries Association’s
Consumer Electronics Group
recommend you to avoid prolonged
exposure from excessive volume
levels.
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE : DO NOT MODIFY
THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly
approved by Yamaha may void your authority,
granted by the FCC, to use the product.
2 IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could
void your FCC authorization to use this product in
the USA.
3 NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result
in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
iii En
Thank you for selecting this YAMAHA subwoofer system.
Please read the following operating precautions before use.
YAMAHA will not be held responsible for any damage and/or
injury caused by not following the cautions below.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this unit in a cool, dry, clean place - away from
windows, heat sources, sources of excessive vibration, dust,
moisture and cold. Avoid sources of humming (transformers,
motors).
3 Never open the cabinet. If something drops into the set, contact
your dealer.
4 The voltage to be used must be the same as that specified on
the rear panel. Using this unit with a higher voltage than
specified is dangerous and may cause a fire and/or electric
shock.
5 To reduce the risk or fire or electric shock, do not expose this
unit to rain or moisture.
6 Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and the
wires connected to other equipments. Never pull the wires
themselves.
7 When not planning to use this unit for a long period (ie.,
vacation, etc.), disconnect the AC power plug from the wall
outlet.
8 Since this unit has a built-in power amplifier, heat will radiate
from the rear panel. Place the unit apart from the walls,
allowing at least 20 cm of space above, behind and on both
sides of the unit to prevent fire or damage. Furthermore, do not
position with the rear panel facing down on the floor or other
surfaces.
9 Do not cover the rear panel of this unit with a newspaper, a
tablecloth, a curtain, etc. in order not to obstruct heat radiation.
If the temperature inside the unit rises, it may cause fire,
damage to the unit and/or personal injury.
10 Do not place the following objects on this unit:
- Glass, china, small metallic etc.
If glass etc. falls by vibrations and breaks, it may cause bodily
injury.
- A burning candle etc.
If the candle falls by vibrations, it may cause fire and bodily
injury.
- A vessel with water in it
If the vessel falls by vibrations and water spills, it may cause
damage to the speaker, and/or you may get an electric shock.
11 Do not place this unit where foreign objects such as water drips
might fall. It might cause a fire, damage to this unit, and/or
personal injury.
12 Never put a hand or a foreign object into the YST port located
on the front side of this unit. When moving this unit, do not
hold the port as it might cause personal injury and/or damage
to this unit.
13 Never place a fragile object near the YST port of this unit. If
the object falls or drops by the air pressure, it may cause
damage to the unit and/or personal injury.
14 Never open the cabinet. It might cause an electric shock since
this unit uses a high voltage. It might also cause personal injury
and/or damage to this unit.
15 When using a humidifier, be sure to avoid condensation inside
this unit by allowing enough spaces around this unit or
avoiding excess humidification. Condensation might cause a
fire, damage to this unit, and/or electric shock.
16 Super-bass frequencies reproduced by this unit may cause a
turntable to generate a howling sound. In such a case, move
this unit away from the turntable.
17 This unit may be damaged if certain sounds are continuously
output at high volume level. For example, if 20 Hz-50 Hz sine
waves from a test disc, bass sounds from electronic
instruments, etc. are continuously output, or when the stylus of
a turntable touches the surface of a disc, reduce the volume
level to prevent this unit from being damaged.
18 If you hear distorted noise (i.e., unnatural, intermittent
“rapping” or “hammering” sounds) coming from this unit,
reduce the volume level. Extremely loud playing of a movie
soundtrack’s low frequency, bass-heavy sounds or similarly
loud popular music passages can damage this speaker system.
19 Vibration generated by super-bass frequencies may distort
images on a TV. In such a case, move this unit away from the
TV set.
20 Do not attempt to clean this unit with chemical solvents as this
might damage the finish. Use a clean, dry cloth.
21 Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that the
unit is faulty.
22 Install this unit near the wall outlet and where the AC power
plug can be reached easily.
23 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
24 Secure placement or installation is the owner’s
responsibility. YAMAHA shall not be liable for any
accident caused by improper placement or installation of
speakers.
CAUTION: Read this before operating your unit.
This unit features a magnetically shielded design, but
there is still a chance that placing it too close to a TV set
might impair picture color. Should this happen, move
this unit away from the TV set.
This unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off. In this state, this unit is designed
to consume a very small quantity of power.
1 En
VOLTAGE SELECTOR
(Asia and General models only)
The voltage selector switch on the rear panel of this
unit must be set for your local main voltage BEFORE
plugging this unit into the AC main supply. Voltages
are 110/120/220/230-240 V AC, 50/60 Hz.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous
if engaged in a live socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
GETTING STARTED ............................................. 2
Features .................................................................. 2
About this manual .................................................. 2
Supplied accessories ............................................. 2
Controls and functions........................................... 3
Preparing the remote control................................. 5
PLACEMENT ........................................................ 6
CONNECTIONS .................................................... 7
Connecting to the amplifier equipped
with subwoofer (line out) terminal(s)........................ 7
Connecting to an amplifier not equipped
with a subwoofer (line out) terminal
........................ 9
Connecting to the ground terminal ..................... 12
Connecting the power cable ................................ 12
USING THIS UNIT ............................................... 13
Adjusting the sound balance............................... 13
Storing the sound balance settings .................... 14
Setting the sleep timer ......................................... 14
Operating the power of this unit using
the remote control of your amplifier ................... 15
Frequency response............................................. 16
Advanced Yamaha
Active Servo Technology II ............................... 17
TROUBLESHOOTING ........................................ 18
SPECIFICATIONS .............................................. 19
IMPORTANT:
THE WIRES IN MAINS LEAD ARE COLOURED
IN ACCORDANCE WITH THE FOLLOWING
CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows: The wire which is coloured
BLUE must be connected to the terminal which is
marked with the letter N or coloured BLACK. The
wire which is coloured BROWN must be connected
to the terminal which is marked with the letter L or
coloured RED. Making sure that neither core is
connected to the earth terminal of the three pin plug.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug
to wide slot and fully insert.
This Class B digital apparatus complies with
Canadian ICES-003.
CONTENTS
1
2
2 En
High 600 W dynamic power
L.F.E input terminal
Sleep timer
Remote control capability
You can make setting changes and adjustments for this
unit by using the remote control from your listening
position.
Advanced Yamaha Active Servo Technology II
This unit employs Advanced Yamaha Active Servo
Technology II which Yamaha has developed for
reproducing higher quality super-bass sound.
Two input connections
This unit can be easily added to your existing audio
system by connecting to either the speaker terminals or
the line output (pin jack) terminals of the amplifier.
Optimum bass sounds with various settings
Setting high cut and phase keeps the optimum sound
quality balance between the front speakers and this unit.
B.A.S.S. mode button
This unit is equipped with the B.A.S.S. mode button so
that you can enjoy bass sound that matches any kind of
source.
In this manual, operations that can be performed using either the front panel of this unit or the remote control are
explained using the remote control.
y indicates a tip for your operation.
Notes contain important information about safety and operating instructions.
Check that you have received all of the following parts.
GETTING STARTED
Features
About this manual
Supplied accessories
Power cable
POWER
STANDBY
SLEEP
PHASE
MEMORY
PRESET
HIGH CUT
VOLUME
213
B.A.S.S.
Remote control
Batteries (2)
(AA, R6, UM-3)
3 En
GETTING STARTED
Front panel
1 Remote control sensor
Receives signals from the remote control.
2 STANDBY/ON indicator
Green: Lights up when this unit is on.
Red: Lights up when this unit is in the standby mode.
Orange: Lights up when the sleep timer is on.
3 PHASE indicator
Green
: Lights up when the phase is set in the reverse mode.
Red: Lights up when the phase is set in the regular mode.
4 STANDBY/ON switch
Turns on or sets this unit to the standby mode.
In the standby mode, this unit consumes a small amount of
power.
5 H-CUT control
Adjusts the high frequency cut off point depending on the
connected front speakers or your preference (see page 13).
6 VOLUME control
Adjusts the volume level. Turn the control clockwise to
increase the volume, counterclockwise to decrease the
volume.
7 B.A.S.S. indicators
Light up to indicate the currently selected B.A.S.S.
number (1, 2 or 3) (see page 13).
8 PRESET indicators
Light up to indicate the currently selected PRESET
number (1, 2 or 3) (see page 14).
If you set this unit to the standby mode when one of the
PRESET indicators is lit, no PRESET indicator lights up
when you turn on this unit next time.
The PRESET indicator turns off when you press any
button other than PRESET 1, 2, or 3, or when you
operate any other function of this unit.
Controls and functions
H-CUT
SUBWOOFER SYSTEM Soavo-900SW
STANDBY
/ON
STANDBY
/ON
PHASE
123123
B.A.S.S.
PRESET
140Hz
40Hz
VOLUME
10
0
1
2
3
456
7
8
Note
H-CUT
140Hz
40Hz
One graduation
of this control
represents 10 Hz.
Notes
4 En
GETTING STARTED
Rear panel
1 GND terminal
See page 12 for connection information.
2 INPUT 3 terminals
See pages 7 - 8 for connection information.
3 INPUT 2 (LFE) terminals
See page 8 for connection information.
4 OUTPUT terminals
See page 10 for connection information.
5 INPUT 1 terminals
See pages 10 - 11 for connection information.
6 AC IN
Connects the supplied power cable (see page 12).
7 POWER switch
Switches the power (ON/OFF) of this unit.
Normally, set this switch to the ON position. When this
unit is not used for a long period of time, set the switch to
the OFF position.
Remote control
1 STANDBY
Sets this unit to the standby mode.
In the standby mode, this unit consumes a small amount of
power.
2 POWER
Turns on this unit.
3 B.A.S.S.
Selects a mode that is suitable for the source.
Each time you press B.A.S.S., the B.A.S.S. indicator
changes between 1, 2, and 3.
4 PRESET
Stores or recalls the B.A.S.S., volume, high-cut frequency
and phase settings (see page 14).
5 HIGH CUT /
Adjusts the high frequency cut off point depending on the
connected front speakers or your preference (see page 13).
6 SLEEP
Sets the sleep timer (see page 14).
7 PHASE
Switches the phase mode.
Normally, set this unit to the reverse position. However,
according to your speaker systems or the listening
condition, there may be cases when better sound quality is
obtained by setting this switch to the normal position.
Select the better position by monitoring the sound.
8 MEMORY
Stores the B.A.S.S., volume, high-cut frequency and phase
settings (see page 14).
9 VOLUME /
Adjusts the volume of this unit.
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
INPUT
3
INPUT
2
INPUT 1
L
L
L
R
R
R
LR
MONO
POWER
ON
OFF
Note
POWER
STANDBY
SLEEP
PHASE
MEMORY
PRESET
HIGH CUT
VOLUME
213
B.A.S.S.
1
2
3
4
59
8
7
6
5 En
GETTING STARTED
Installing the batteries in the remote
control
1 Press the mark on the battery cover and
open the cover.
2 Insert the two supplied type AA, R6, UM-3
batteries following the indications (+/–)
inside the battery compartment.
3 Close the battery cover.
Replacing the batteries
Change all of the batteries if you notice conditions such as
the operation range of the remote control decreases.
Do not use an old battery together with a new one.
Do not use different types of batteries (for example,
alkaline and manganese) together. Each type of battery
has its own characteristics even if they are similar in
shape.
If the batteries run out, immediately remove them from
the remote control to prevent an explosion or acid leak.
Dispose of the batteries according to the regional
regulations.
If a battery starts leaking, dispose of it immediately. Be
careful not to let leaking battery acid come into contact
with your skin or clothing. Before inserting new
batteries, wipe the compartment clean.
Using the remote control
The remote control transmits a directional infrared ray. Be
sure to aim the remote control directly at the remote control
sensor on the main unit during operation.
Handling the remote control
Be careful not to spill liquid on the remote control.
Be careful not to drop the remote control.
Do not leave the remote control in the following places:
– hot or humid places, such as near a heater or in a
bathroom
– extremely cold places
– dusty places
Preparing the remote control
Notes
3
1
2
Remote control
sensor
Approximately
6 m (20 ft)
6 En
The position of the subwoofer is not so critical because bass sound is not highly directional. For a sonorous sound field,
the use of two subwoofers is recommended, although you can obtain a good effect with one subwoofer. ( : subwoofer,
: front speaker)
When using one subwoofer
Place the subwoofer on the outside of either the right or the
left front speaker.
y
If the subwoofer is placed directly facing the wall, the bass
sound may lessen because the sound from the subwoofer
and the sound reflected by the wall may cancel each other
out. To prevent this from happening, face the subwoofer
obliquely to the wall ( or ).
When using two subwoofers
Place the subwoofers on the outside of each front speaker.
PLACEMENT
A
A B
B
7 En
See pages 7 - 8 when your amplifier has subwoofer (line out) terminal(s), or see pages 9 - 11 when your amplifier has no
subwoofer (line out) terminal.
Do not connect the power cord of this unit and other components into an AC outlet until all connections between
components are completed.
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. Also, refer to the owner’s
manual of your component to be connected to this unit.
The connection methods or the names of the terminals may differ depending on the component. Refer to the owner’s
manual of your component as well.
When your amplifier has a one-channel subwoofer terminal
Connect the subwoofer (or low pass etc.) terminal of your amplifier to the INPUT 3 ( /MONO) terminal of this unit
using a commercially available mono pin cable.
When your amplifier has two-channel subwoofer terminals
Using one subwoofer
Connect the “L” side subwoofer terminal of your amplifier to the INPUT 3 ( /MONO) terminal of this unit and “R” side
subwoofer terminal of your amplifier to the INPUT 3 ( ) terminal of this unit using a commercially available audio pin
cable.
Some amplifiers have line output terminals labeled PRE OUT. When you connect this unit to the PRE OUT terminals
of the amplifier, make sure that the amplifier has at least two sets of PRE OUT terminals. If the amplifier has only one
set of PRE OUT terminals, do not connect this unit to the PRE OUT terminals. Instead, connect this unit to the speaker
terminals of the amplifier (see pages 9 - 10).
When connecting to a monaural line output terminal of the amplifier, connect the INPUT 3 ( /MONO) terminal.
When connecting to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT
terminals on the rear panel of this unit. If connected, they will not produce sound.
CONNECTIONS
Notes
Connecting to the amplifier equipped with subwoofer (line out) terminal(s)
1
L
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
Amplifier
Mono pin cable (not included)
Subwoofer
L
R
Notes
L
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
Audio pin
cable
(not included)
Amplifier
Subwoofer
8 En
CONNECTIONS
Using two subwoofers
Connect the “R” side subwoofer terminal of your amplifier to the INPUT 3 ( ) terminal on this unit using a commercially
available mono pin cable, and connect the “L” side subwoofer terminal of your amplifier to the INPUT 3 ( /MONO)
terminal of this unit using a commercially available mono pin cable.
Connecting to an amplifier equipped with a high cut function
If your amplifier can cut off high frequencies from the signals for sending to the subwoofer, connect
the amplifier to the INPUT 2 (LFE) terminal of this unit. This brings you higher sound quality
because the signal routing in this unit is shortened by bypassing the built-in HIGH CUT (high cut)
circuit.
R
L
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
INPUT
3
INPUT
2
INPUT 1
Mono pin cable
(not included)
Amplifier
Subwoofer
Subwoofer
L
L
R
R
R
R
MONO
INPUT
3
INPUT
2
9 En
CONNECTIONS
Connect an amplifier (and front speakers) to this unit using commercially available speaker cables. Refer to the following
instructions to make connections.
Connecting to the speaker cable
1 Remove approximately 10 mm (3/8”) of
insulation from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
3 Turn the knob counterclockwise to loosen.
4 Insert the bare wire into the hole in the side
of each terminal.
5 Turn the knob clockwise to tighten.
6 Test the firmness of the connection by
pulling gently on the cable at the terminal.
Do not let the bare speaker wires touch each other,
because this could damage this unit or the amplifier,
or both of them.
For connection, keep the speaker cables as short as
possible. Do not bundle or roll up the excess part of the
cables. If the connections are faulty, no sound will be
heard from this unit or the speakers, or both of them.
Make sure that the + and – polarity markings of the
speaker terminals are observed and set correctly. If these
cables are reversed, the sound will be unnatural and lack
bass.
Do not insert the insulation into the hole. The sound may
not be produced.
Banana plug connection
1 Tighten the knob.
2 Insert the banana plug connecter into the
end of the corresponding terminal.
Connecting to an amplifier not equipped with a subwoofer (line out) terminal
2
Notes
12
5
3
4
10 mm
(3/8”)
1
2
10 En
CONNECTIONS
When your amplifier has one set of front speaker terminals
Connect the speaker terminals of the amplifier to the INPUT 1 terminals of this unit, and connect the OUTPUT terminals
of this unit to the front speakers using a commercially available speaker cable.
y
Connecting front speakers via this unit does not affect the sound quality.
Using one subwoofer
Using two subwoofers
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
Front speaker (R) Front speaker (L)
Speaker terminals
Amplifier
Subwoofer
OUTPUT
TO SPEAKERS
FROM
AMPLIFIER
INPUT 3
INPUT 2
L
L
L
R
R
R
LR
MONO
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
INPUT
3
INPUT
2
INPUT 1
Front speaker (R) Front speaker (L)
Speaker terminals
Subwoofer (R)
Amplifier
Subwoofer (L)
11 En
CONNECTIONS
When your amplifier has two sets of front speaker terminals and both terminals can output
sound signals simultaneously
Connect one set of front speaker terminals of the amplifier to the INPUT 1 terminals of this unit, and connect another
set of front speaker terminals of the amplifier to the front speakers using commercially available speaker cables.
Set the amplifier so that both sets of front speaker terminals output sound signals simultaneously.
When your amplifier cannot output sound signals simultaneously even if you connect in this way, follow “When your
amplifier has one set of front speaker terminals” on page 10.
Using one subwoofer
Using two subwoofers
Note
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
Front speaker (R)
Front speaker (L)
Speaker
terminals
Amplifier
Subwoofer
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
INPUT
3
INPUT
2
INPUT 1
Front speaker (R)
Speaker
terminals
Front speaker (L)
Subwoofer (R) Subwoofer (L)
Amplifier
12 En
CONNECTIONS
If this unit or the amplifier makes a hamming noise when
connecting to the speaker terminals of your amplifier,
connect both of the GND (ground) terminals on your
amplifier and this unit using commercially available
grounding wire as shown in fig. .
When your amplifier has no GND (ground) terminal,
connect to the screw that fastens the top cover of your
amplifier as shown in fig. .
When connecting the GND (ground) terminal, make sure
the power cables of the amplifier and this unit are not
plugged into the AC outlet.
Plug the supplied power cable into the AC IN of this unit
after all other connections are complete, and then plug the
power cable to an AC outlet.
Do not use other power cables. Use the provided cable.
Use of other power cables may result in fire hazard or
electrical shock.
Do not plug the power cable into the AC outlet of your
amplifier. Doing so may create distorted sounds or turn
off the power of your amplifier.
Connecting to the ground terminal
Note
A
B
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
INPUT 1
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
A B
Connecting the power cable
Notes
POWER
ON
OFF
To the AC
outlet
13 En
Before using this unit, adjust the volume balance of this unit to obtain the optimum volume and tone balance between the
front speakers and this unit by following the procedures below.
1 Set POWER switch on the rear panel of this
unit to the ON position, and then press
POWER to turn on this unit.
The STANDBY/ON indicator lights up green.
2 Press VOLUME to set the volume level of
this unit to the minimum (0).
3 Turn on the power of all other components.
4 Play back a source containing low-
frequency components and adjust the
volume level of your amplifier to the desired
listening level.
Set the tone control on your amplifier to the center
position.
5 Press HIGH CUT / to adjust to the
position where the desired response can be
obtained.
Normally, set the position to a level slightly higher
than the minimum frequency of the front speaker.
* To find out the minimum frequency of the front
speaker, refer to the owner’s manual of the front
speaker.
6 Press VOLUME to increase the volume
gradually to adjust the volume balance
between the front speaker and this unit.
Normally, set the volume to a level where you can
obtain a little more bass effect than when this unit is not
used.
y
If you cannot obtain the desired response, repeat steps
5 and 6.
7 Press PHASE to select the regular or
reverse mode.
Normally, set it to the reverse mode. If you cannot
obtain the desired response, set it to the regular mode.
8 Press B.A.S.S. to select a mode that is
suitable for the source.
1: WIDE
When a movie source is played, the low- frequency
effects are enhanced so that you can enjoy more
powerful sound.
2: NORMAL
When a music or movie etc. source is played, you can
enjoy natural bass sounds.
3: NARROW
When an ordinary music source is played, the
excessive low-frequency signals are cut off to make the
sound clearer.
USING THIS UNIT
Adjusting the sound balance
POWER
ON
OFF
POWER
STANDBY
SLEEP
PHASE
MEMORY
PRESET
HIGH CUT
VOLUME
213
B.A.S.S.
1
2,6
1
Remote control Rear panel
SUB
W
STANDBY
/ON
14 En
USING THIS UNIT
You can store up to 3 sets of your favorite settings (volume,
high-cut, phase and B.A.S.S. setting) in this unit.
Storing the setting
In the following procedure, PRESET 1 is used as an
example.
1 Adjust the sound balance between the
volume, high cut, phase and
B.A.S.S. (see
page 13).
2 Press MEMORY.
The PRESET indicators on the front panel flash.
3 Press PRESET 1.
The PRESET 1 indicator lights up. The current setting
is stored as PRESET 1.
y
In step 3, pressing a stored number overwrites the old
setting.
While the VOLUME control or the H-CUT control is
rotating by pressing a PRESET, pressing another
PRESET is ineffective.
Recalling a setting
Press PRESET you want to recall (1, 2 or 3).
Memory back-up
Even if you turn off this unit by using the POWER switch
on the rear panel, this unit recalls the last setting when the
power is turned back on (Last memory function).
If the power is cut for more than one week, the setting is
cleared.
If you set the sleep timer, this unit automatically turns to
the standby mode after 120 minutes.
Press SLEEP.
The color of the STANDBY/ON indicator changes to
orange.
Pressing SLEEP again cancels the sleep timer.
Storing the sound balance settings
POWER
STANDBY
SLEEP
PHASE
MEMORY
PRESET
HIGH CUT
VOLUME
213
B.A.S.S.
H-CUT
SUBWOOFER SYSTEM Soavo-900SW
STANDBY
/ON
STANDBY
/ON
PHASE
123123
B.A.S.S.
PRESET
1
00H
z
40Hz
VOLUM E
10
0
1
1
1
2
1
1
3
Remote control
Front panel
STANDBY/ON indicator
900SW
3 123
PRESET
Note
Setting the sleep timer
POWER
STANDBY
SLEEP
PHASE
MEMORY
PRESET
HIGH CUT
VOLUME
213
B.A.S.S.
SLEEP
SUB
W
STANDBY
/ON
15 En
USING THIS UNIT
* This function is available only for Yamaha amplifiers
that meet the following conditions:
– The amplifier was released in 2005 or later.
– The remote control of the amplifier has two different
buttons for STANDBY and ON.
When the AMP ID library code of the remote control has
been changed, this function may not work.
Setting
1 Set POWER switch on the rear panel to the
OFF position.
2 Set POWER switch to the ON position while
pressing and holding
STANDBY/ON switch
on the front panel.
Continue holding down
STANDBY/ON
switch for 3 seconds or longer.
After the STANDBY/ON indicator flashes 4 times, the
setting is completed.
Canceling
1 Set POWER switch on the rear panel to the
OFF position.
2 Set POWER switch to the ON position while
pressing and holding
STANDBY/ON switch
on the front panel.
Continue holding down
STANDBY/ON
switch for 3 seconds or longer.
After the STANDBY/ON indicator flashes 2 times, the
setting is completed.
Place this unit within the operating range of the remote
control of the amplifier. If you place this unit far away from
the amplifier, you may not be able to operate this unit with
the remote control.
Operating the power of this unit using
the remote control of your amplifier
Note
H-CUT
SUBWOOFER SYSTEM Soavo-900SW
STANDBY
/ON
STANDBY
/ON
PHASE
123123
B.A.S.S.
PRESET
10
0H
z
4
0
H
z
VOLUM E
10
0
POWER
ON
OFF
POWER switch
STANDBY/ON switch
Rear panel
Front panel
SUB
W
STANDBY
/ON
Note
SUB
W
STANDBY
/ON
16 En
USING THIS UNIT
Frequency response of this unit
The figures below show the optimum adjustment of each control and the frequency response when this subwoofer is
combined with a typical front speaker system.
EX.1 When combined with a 10 cm or 13 cm (3-15/16” or 5-2/16”) acoustic suspension, 2 way system
front speakers
If you are using Soavo-1 speakers as front speakers, use the following example as a reference when adjusting settings.
EX.2 When combined with a 20 cm or 25 cm (7-14/16” or 9-13/16”) acoustic suspension, 2 way system
front speakers
* These diagrams do not depict actual frequency response characteristics accurately.
Frequency response
reverse mode
(Green)
reverse mode
(Green)
20 50 100 200 500Hz
40
50
60
70
80
90
dB
H-CUT 140 Hz
Frequency response graph*
H-CUT
140Hz
40Hz
VOLUME
10
0
(H-CUT) (VOLUME)
O
OFER SYSTEM
S
PHASE
1
(PHASE)
20 50 100 200 500Hz
40
50
60
70
80
90
dB
Soavo-900SW (H-CUT 60 - 70 Hz)
Front
speaker
Frequency response graph*
H-CUT
140Hz
40Hz
VOLUME
10
0
(H-CUT) (VOLUME)
O
OFER SYSTEM
S
PHASE
1
(PHASE)
20 50 100 200 500Hz
40
50
60
70
80
90
dB
Soavo-900SW (H-CUT 50 - 60Hz)
Front
speaker
Frequency response graph*
17 En
In 1988, Yamaha brought to the speaker systems utilizing
YST (Yamaha Active Servo Technology) to give powerful,
high quality bass reproduction. This technology uses a
direct connection between the amplifier and speaker,
allowing accurate signal transmission and precise speaker
control.
As this technology uses speaker units controlled by the
negative impedance drive of the amplifier and resonance
generated between the cabinet capacity volume and port, it
creates more resonant energy (the “air woofer” concept)
than the standard bass reflex method. This allows for bass
reproduction from much smaller cabinets than was
previously possible.
Yamaha’s newly developed Advanced YST II adds many
refinements to Yamaha Active Servo Technology,
allowing better control of the forces driving the amplifier
and speaker. From the amplifier’s point of view, the
speaker impedance changes depending on the sound
frequency. Yamaha developed a new circuit design
combining negative-impedance and constant-current
drives, which provides a more stable performance and
clear bass reproduction without any murkiness.
Advanced Yamaha Active Servo Technology II
High-amplitude
bass sound
Port
Cabinet
Advanced impedance Converter
Active
Servo
Processing
Amplifier
Signals of low amplitude
Air woofer
(Helmholtz resonator)
Signals
18 En
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instructions given below do not help, disconnect the power cord and contact your authorized Yamaha dealer or
service center.
When an excessive level of signal is input to this unit for 5 to 15 minutes, the POWER indicator starts flashing to alarm
you of the danger of damaging the power amplifier and speaker of this unit. If the signal input lasts for 5 minutes more,
this unit turns into the standby mode automatically.
When an enormous amount of signal is input, the power of this unit is turned off immediately. To turn on this unit again,
press STANDBY/ON switch on the front panel.
TROUBLESHOOTING
Problem Cause Remedy
Power is not supplied even though
the STANDBY/ON switch is
pressed.
The power plug is not securely connected. Connect it securely.
The POWER switch is set to the OFF
position.
Set the POWER switch to the ON
position.
No sound. The volume is set to the minimum (0). Raise the volume.
Speaker cables are not connected securely. Connect them securely.
The signals from the amplifier are too low. Increase the volume of the amplifier or the
component connected to the amplifier.
The signal from the subwoofer output
terminal of the amplifier is not output.
Check the speaker mode setting on the
amplifier.
Sound level is too low. Speaker cables are not connected correctly. Connect them correctly, that is L (left) to
L, R (right) to R, “+” to “+” and
“–” to “–”.
Setting of the phase is not proper. Set the phase to the other position.
A source sound with few bass frequencies is
being played.
Play a source sound with bass
frequencies.
Set the H-CUT to a higher position.
It is influenced by standing waves. Reposition this unit or break up the
parallel surface by placing bookshelves
etc. along the walls.
The remote control does not
work.
Wrong distance or angle. Use the remote control within a maximum
range of 6 m and no more then 30 degrees
off-axis from the front panel.
Direct sunlight or lighting from an inverter
type of fluorescent lamp etc. is striking the
remote control sensor of this unit.
Reposition this unit.
The batteries are weak. Replace all batteries.
This unit is not turned on with the
remote control of the amplifier.
(when setting “Operating the
power of this unit using the
remote control of your
amplifier”)
Wrong distance or angle. Place this unit within the operating range
of the remote control of the amplifier.
The household breaker goes off. This unit consumes much electricity when a
high level signal is input to this unit.
Turn down the volume on the amplifier
etc. connected to this unit or cut off the
power of other unused equipment.
Notes
19 En
Type .... Advanced Yamaha Active Servo Technology II
Driver ...................................... 25 cm (10”) cone woofer
Magnetic shielding type
Amplifier Output (100 Hz, 4 ohms, 10% T.H.D)
............................................................................... 600 W
Frequency Response ............................. 18 Hz - 160 Hz
Power Supply
U.S.A. and Canada models ............. AC 120 V, 60 Hz
U.K. and Europe models ................ AC 230 V, 50 Hz
Australia model .............................. AC 240 V, 50 Hz
Asia and General models
....................... AC 110/120/220/230-240 V, 50/60 Hz
Korea model ................................... AC 220 V, 60 Hz
China model ................................... AC 220 V, 50 Hz
Power Consumption ........................................... 180 W
Standby Power Consumption ............................. 0.5 W
Dimensions (W x H x D)
.......................................... 410 mm x 457 mm x 462 mm
(16-1/8” x 17” x 18-3/16”)
Weight ............................................. 32 kg (70 lbs. 9 oz.)
Please note that all specifications are subject to change
without notice.
SPECIFICATIONS
©2006 All rights reserved.
YAMAHA ELECTRONICS CORPORATION, USA
6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.
135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.
SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.
RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.
YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD.
17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Indonesia WH59770

Transcripción de documentos

UB Soavo-900SW SUBWOOFER SYSTEM OWNER’S MANUAL IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT Please record the serial number of this system in the space below. Model: Serial No.: The serial number is located on the rear of the main unit. Retain this Owner’s Manual in a safe place for future reference. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 Only use attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. • Be sure to allow spaces of at least 20 cm above, behind and on both sides of the unit. • Do not place the following objects on the unit: A vessel with water in it. If the vessel falls by vibrations and water spills, it may cause damage to the unit, and/or you may get an electric shock. i En FCC INFORMATION (for US customers) We Want You Listening For A Lifetime 1 IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2 IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3 NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. ii En Thank you for selecting this YAMAHA subwoofer system. CAUTION: Read this before operating your unit. Please read the following operating precautions before use. YAMAHA will not be held responsible for any damage and/or injury caused by not following the cautions below. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this unit in a cool, dry, clean place - away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). 3 Never open the cabinet. If something drops into the set, contact your dealer. 4 The voltage to be used must be the same as that specified on the rear panel. Using this unit with a higher voltage than specified is dangerous and may cause a fire and/or electric shock. 5 To reduce the risk or fire or electric shock, do not expose this unit to rain or moisture. 6 Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipments. Never pull the wires themselves. 7 When not planning to use this unit for a long period (ie., vacation, etc.), disconnect the AC power plug from the wall outlet. 8 Since this unit has a built-in power amplifier, heat will radiate from the rear panel. Place the unit apart from the walls, allowing at least 20 cm of space above, behind and on both sides of the unit to prevent fire or damage. Furthermore, do not position with the rear panel facing down on the floor or other surfaces. 9 Do not cover the rear panel of this unit with a newspaper, a tablecloth, a curtain, etc. in order not to obstruct heat radiation. If the temperature inside the unit rises, it may cause fire, damage to the unit and/or personal injury. 10 Do not place the following objects on this unit: - Glass, china, small metallic etc. If glass etc. falls by vibrations and breaks, it may cause bodily injury. - A burning candle etc. If the candle falls by vibrations, it may cause fire and bodily injury. - A vessel with water in it If the vessel falls by vibrations and water spills, it may cause damage to the speaker, and/or you may get an electric shock. 11 Do not place this unit where foreign objects such as water drips might fall. It might cause a fire, damage to this unit, and/or personal injury. 12 Never put a hand or a foreign object into the YST port located on the front side of this unit. When moving this unit, do not hold the port as it might cause personal injury and/or damage to this unit. 13 Never place a fragile object near the YST port of this unit. If the object falls or drops by the air pressure, it may cause damage to the unit and/or personal injury. 14 Never open the cabinet. It might cause an electric shock since this unit uses a high voltage. It might also cause personal injury and/or damage to this unit. iii En 15 When using a humidifier, be sure to avoid condensation inside this unit by allowing enough spaces around this unit or avoiding excess humidification. Condensation might cause a fire, damage to this unit, and/or electric shock. 16 Super-bass frequencies reproduced by this unit may cause a turntable to generate a howling sound. In such a case, move this unit away from the turntable. 17 This unit may be damaged if certain sounds are continuously output at high volume level. For example, if 20 Hz-50 Hz sine waves from a test disc, bass sounds from electronic instruments, etc. are continuously output, or when the stylus of a turntable touches the surface of a disc, reduce the volume level to prevent this unit from being damaged. 18 If you hear distorted noise (i.e., unnatural, intermittent “rapping” or “hammering” sounds) coming from this unit, reduce the volume level. Extremely loud playing of a movie soundtrack’s low frequency, bass-heavy sounds or similarly loud popular music passages can damage this speaker system. 19 Vibration generated by super-bass frequencies may distort images on a TV. In such a case, move this unit away from the TV set. 20 Do not attempt to clean this unit with chemical solvents as this might damage the finish. Use a clean, dry cloth. 21 Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. 22 Install this unit near the wall outlet and where the AC power plug can be reached easily. 23 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. 24 Secure placement or installation is the owner’s responsibility. YAMAHA shall not be liable for any accident caused by improper placement or installation of speakers. This unit features a magnetically shielded design, but there is still a chance that placing it too close to a TV set might impair picture color. Should this happen, move this unit away from the TV set. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. In this state, this unit is designed to consume a very small quantity of power. • VOLTAGE SELECTOR (Asia and General models only) The voltage selector switch on the rear panel of this unit must be set for your local main voltage BEFORE plugging this unit into the AC main supply. Voltages are 110/120/220/230-240 V AC, 50/60 Hz. For U.K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. SPECIAL INSTRUCTIONS FOR U.K. MODEL IMPORTANT: THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. CONTENTS GETTING STARTED ............................................. 2 Features .................................................................. 2 About this manual .................................................. 2 Supplied accessories ............................................. 2 Controls and functions........................................... 3 Preparing the remote control................................. 5 PLACEMENT ........................................................ 6 CONNECTIONS .................................................... 7 1 Connecting to the amplifier equipped with subwoofer (line out) terminal(s) ........................ 7 2 Connecting to an amplifier not equipped with a subwoofer (line out) terminal ........................ 9 Connecting to the ground terminal ..................... 12 Connecting the power cable ................................ 12 USING THIS UNIT ............................................... 13 Adjusting the sound balance............................... 13 Storing the sound balance settings .................... 14 Setting the sleep timer ......................................... 14 Operating the power of this unit using the remote control of your amplifier ................... 15 Frequency response............................................. 16 Advanced Yamaha Active Servo Technology II ............................... 17 TROUBLESHOOTING ........................................ 18 SPECIFICATIONS .............................................. 19 FOR CANADIAN CUSTOMERS To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003. 1 En GETTING STARTED Features ◆ High 600 W dynamic power ◆ Two input connections This unit can be easily added to your existing audio system by connecting to either the speaker terminals or the line output (pin jack) terminals of the amplifier. ◆ L.F.E input terminal ◆ Sleep timer ◆ Remote control capability You can make setting changes and adjustments for this unit by using the remote control from your listening position. ◆ Advanced Yamaha Active Servo Technology II This unit employs Advanced Yamaha Active Servo Technology II which Yamaha has developed for reproducing higher quality super-bass sound. ◆ Optimum bass sounds with various settings Setting high cut and phase keeps the optimum sound quality balance between the front speakers and this unit. ◆ B.A.S.S. mode button This unit is equipped with the B.A.S.S. mode button so that you can enjoy bass sound that matches any kind of source. About this manual • In this manual, operations that can be performed using either the front panel of this unit or the remote control are explained using the remote control. • y indicates a tip for your operation. • Notes contain important information about safety and operating instructions. Supplied accessories Check that you have received all of the following parts. Batteries (2) (AA, R6, UM-3) Power cable POWER STANDBY SLEEP B.A.S.S. PHASE MEMORY 1 HIGH CUT PRESET 2 3 VOLUME Remote control 2 En GETTING STARTED Controls and functions ■Front panel 1 2 3 SUBWOOFER SYSTEM Soavo-900SW 1 STANDBY /ON 2 3 1 B.A.S.S. PHASE 2 3 PRESET 8 7 4 10 0 Hz 40 14 0H z STANDBY /ON H-CUT VOLUME 5 6 1 Remote control sensor 6 VOLUME control Receives signals from the remote control. Adjusts the volume level. Turn the control clockwise to increase the volume, counterclockwise to decrease the volume. 2 STANDBY/ON indicator Green: Lights up when this unit is on. Red: Lights up when this unit is in the standby mode. Orange: Lights up when the sleep timer is on. 3 PHASE indicator Green: Lights up when the phase is set in the reverse mode. Red: Lights up when the phase is set in the regular mode. 4 STANDBY/ON switch Turns on or sets this unit to the standby mode. Note In the standby mode, this unit consumes a small amount of power. 7 B.A.S.S. indicators Light up to indicate the currently selected B.A.S.S. number (1, 2 or 3) (see page 13). 8 PRESET indicators Light up to indicate the currently selected PRESET number (1, 2 or 3) (see page 14). Notes • If you set this unit to the standby mode when one of the PRESET indicators is lit, no PRESET indicator lights up when you turn on this unit next time. • The PRESET indicator turns off when you press any button other than PRESET 1, 2, or 3, or when you operate any other function of this unit. 5 H-CUT control 14 Hz 0H 40 One graduation of this control represents 10 Hz. z Adjusts the high frequency cut off point depending on the connected front speakers or your preference (see page 13). H-CUT 3 En GETTING STARTED ■Rear panel L MONO L R OUTPUT TO SPEAKERS POWER L ON OFF R R INPUT 3 INPUT 2 R FROM AMPLIFIER INPUT 1 L 1 GND terminal 5 INPUT 1 terminals See page 12 for connection information. See pages 10 - 11 for connection information. 2 INPUT 3 terminals 6 AC IN See pages 7 - 8 for connection information. Connects the supplied power cable (see page 12). 3 INPUT 2 (LFE) terminals 7 POWER switch See page 8 for connection information. Switches the power (ON/OFF) of this unit. Normally, set this switch to the ON position. When this unit is not used for a long period of time, set the switch to the OFF position. 4 OUTPUT terminals See page 10 for connection information. ■Remote control 3 B.A.S.S. 1 2 3 4 5 POWER STANDBY SLEEP PHASE B.A.S.S. MEMORY 1 HIGH CUT PRESET 2 6 7 8 3 VOLUME 9 Selects a mode that is suitable for the source. Each time you press B.A.S.S., the B.A.S.S. indicator changes between 1, 2, and 3. 4 PRESET Stores or recalls the B.A.S.S., volume, high-cut frequency and phase settings (see page 14). 5 HIGH CUT / Adjusts the high frequency cut off point depending on the connected front speakers or your preference (see page 13). 6 SLEEP Sets the sleep timer (see page 14). 7 PHASE 1 STANDBY Sets this unit to the standby mode. Note In the standby mode, this unit consumes a small amount of power. 2 POWER Turns on this unit. Switches the phase mode. Normally, set this unit to the reverse position. However, according to your speaker systems or the listening condition, there may be cases when better sound quality is obtained by setting this switch to the normal position. Select the better position by monitoring the sound. 8 MEMORY Stores the B.A.S.S., volume, high-cut frequency and phase settings (see page 14). 9 VOLUME / Adjusts the volume of this unit. 4 En GETTING STARTED Preparing the remote control ■Installing the batteries in the remote control 3 ■Using the remote control 1 2 Remote control sensor Approximately 6 m (20 ft) 1 Press the mark on the battery cover and open the cover. 2 Insert the two supplied type AA, R6, UM-3 batteries following the indications (+/–) inside the battery compartment. 3 Close the battery cover. The remote control transmits a directional infrared ray. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation. Replacing the batteries Change all of the batteries if you notice conditions such as the operation range of the remote control decreases. Handling the remote control Notes • Do not use an old battery together with a new one. • Do not use different types of batteries (for example, alkaline and manganese) together. Each type of battery has its own characteristics even if they are similar in shape. • If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak. • Dispose of the batteries according to the regional regulations. • If a battery starts leaking, dispose of it immediately. Be careful not to let leaking battery acid come into contact with your skin or clothing. Before inserting new batteries, wipe the compartment clean. Be careful not to drop the remote control. Be careful not to spill liquid on the remote control. Do not leave the remote control in the following places: – hot or humid places, such as near a heater or in a bathroom – extremely cold places – dusty places 5 En PLACEMENT The position of the subwoofer is not so critical because bass sound is not highly directional. For a sonorous sound field, the use of two subwoofers is recommended, although you can obtain a good effect with one subwoofer. ( : subwoofer, : front speaker) ■When using one subwoofer ■When using two subwoofers Place the subwoofer on the outside of either the right or the left front speaker. Place the subwoofers on the outside of each front speaker. A y If the subwoofer is placed directly facing the wall, the bass sound may lessen because the sound from the subwoofer and the sound reflected by the wall may cancel each other out. To prevent this from happening, face the subwoofer obliquely to the wall ( A or B ). 6 En B CONNECTIONS See pages 7 - 8 when your amplifier has subwoofer (line out) terminal(s), or see pages 9 - 11 when your amplifier has no subwoofer (line out) terminal. Notes • Do not connect the power cord of this unit and other components into an AC outlet until all connections between components are completed. • Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. Also, refer to the owner’s manual of your component to be connected to this unit. • The connection methods or the names of the terminals may differ depending on the component. Refer to the owner’s manual of your component as well. 1 Connecting to the amplifier equipped with subwoofer (line out) terminal(s) When your amplifier has a one-channel subwoofer terminal Connect the subwoofer (or low pass etc.) terminal of your amplifier to the INPUT 3 ( L /MONO) terminal of this unit using a commercially available mono pin cable. Mono pin cable (not included) L MONO L R R INPUT 3 INPUT 2 R Subwoofer R OUTPUT TO SPEAKERS FROM AMPLIFIER INPUT 1 L Amplifier L When your amplifier has two-channel subwoofer terminals ■Using one subwoofer Connect the “L” side subwoofer terminal of your amplifier to the INPUT 3 ( L /MONO) terminal of this unit and “R” side subwoofer terminal of your amplifier to the INPUT 3 ( R ) terminal of this unit using a commercially available audio pin cable. Notes • Some amplifiers have line output terminals labeled PRE OUT. When you connect this unit to the PRE OUT terminals of the amplifier, make sure that the amplifier has at least two sets of PRE OUT terminals. If the amplifier has only one set of PRE OUT terminals, do not connect this unit to the PRE OUT terminals. Instead, connect this unit to the speaker terminals of the amplifier (see pages 9 - 10). • When connecting to a monaural line output terminal of the amplifier, connect the INPUT 3 ( L /MONO) terminal. • When connecting to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT terminals on the rear panel of this unit. If connected, they will not produce sound. Subwoofer L MONO L R INPUT 3 R INPUT 2 R OUTPUT TO SPEAKERS L Audio pin cable (not included) R FROM AMPLIFIER INPUT 1 L Amplifier 7 En CONNECTIONS ■Using two subwoofers Connect the “R” side subwoofer terminal of your amplifier to the INPUT 3 ( R ) terminal on this unit using a commercially available mono pin cable, and connect the “L” side subwoofer terminal of your amplifier to the INPUT 3 ( L /MONO) terminal of this unit using a commercially available mono pin cable. L MONO L R INPUT 3 R INPUT 2 R R Subwoofer OUTPUT TO SPEAKERS FROM AMPLIFIER INPUT 1 L L Subwoofer L MONO L R R INPUT 3 INPUT 2 R R OUTPUT TO SPEAKERS FROM AMPLIFIER INPUT 1 L L Mono pin cable (not included) Amplifier ■Connecting to an amplifier equipped with a high cut function L MONO R INPUT 3 L R R INPUT 2 R 8 En If your amplifier can cut off high frequencies from the signals for sending to the subwoofer, connect the amplifier to the INPUT 2 (LFE) terminal of this unit. This brings you higher sound quality because the signal routing in this unit is shortened by bypassing the built-in HIGH CUT (high cut) circuit. CONNECTIONS 2 Connecting to an amplifier not equipped with a subwoofer (line out) terminal Connect an amplifier (and front speakers) to this unit using commercially available speaker cables. Refer to the following instructions to make connections. ■Connecting to the speaker cable 1 ■Banana plug connection 2 10 mm (3/8”) 2 1 4 3 5 1 Remove approximately 10 mm (3/8”) of insulation from each of the speaker cables. 2 Twist the exposed wires of the cable together to prevent short circuits. 3 Turn the knob counterclockwise to loosen. 4 Insert the bare wire into the hole in the side of each terminal. 5 Turn the knob clockwise to tighten. 6 Test the firmness of the connection by pulling gently on the cable at the terminal. 1 Tighten the knob. 2 Insert the banana plug connecter into the end of the corresponding terminal. Notes • Do not let the bare speaker wires touch each other, because this could damage this unit or the amplifier, or both of them. • For connection, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the connections are faulty, no sound will be heard from this unit or the speakers, or both of them. • Make sure that the + and – polarity markings of the speaker terminals are observed and set correctly. If these cables are reversed, the sound will be unnatural and lack bass. • Do not insert the insulation into the hole. The sound may not be produced. 9 En CONNECTIONS When your amplifier has one set of front speaker terminals Connect the speaker terminals of the amplifier to the INPUT 1 terminals of this unit, and connect the OUTPUT terminals of this unit to the front speakers using a commercially available speaker cable. y Connecting front speakers via this unit does not affect the sound quality. ■Using one subwoofer Front speaker (R) Front speaker (L) L MONO L R R INPUT 3 INPUT 2 OUTPUT TO SPEAKERS R R FROM AMPLIFIER INPUT 1 L L Amplifier Subwoofer Speaker terminals ■Using two subwoofers Front speaker (R) Front speaker (L) LL MONO MONO LL R R R R INPUT 2 INPUT 2 INPUT 3 INPUT 3 R R R R OUTPUT OUTPUT TO TO SPEAKERS SPEAKERS FROM FROM AMPLIFIER INPUT 1 AMPLIFIER LL L R R INPUT 3 INPUT 2 LL Speaker terminals R R Amplifier Subwoofer (R) 10 En L MONO OUTPUT TO SPEAKERS FROM AMPLIFIER INPUT 1 L L Subwoofer (L) CONNECTIONS When your amplifier has two sets of front speaker terminals and both terminals can output sound signals simultaneously • Connect one set of front speaker terminals of the amplifier to the INPUT 1 terminals of this unit, and connect another set of front speaker terminals of the amplifier to the front speakers using commercially available speaker cables. • Set the amplifier so that both sets of front speaker terminals output sound signals simultaneously. Note When your amplifier cannot output sound signals simultaneously even if you connect in this way, follow “When your amplifier has one set of front speaker terminals” on page 10. ■Using one subwoofer Front speaker (L) Front speaker (R) L MONO L R R INPUT 2 INPUT 3 Subwoofer Speaker terminals R R OUTPUT TO SPEAKERS FROM AMPLIFIER INPUT 1 L L Amplifier ■Using two subwoofers L MONO L R OUTPUT TO SPEAKERS L MONO L L R R R R INPUT 3 INPUT 2 INPUT 3 INPUT 2 R FROM AMPLIFIER INPUT 1 Subwoofer (R) L Subwoofer (L) Front speaker (R) R R OUTPUT TO SPEAKERS FROM AMPLIFIER INPUT 1 L L Front speaker (L) Speaker terminals Amplifier 11 En CONNECTIONS Connecting to the ground terminal If this unit or the amplifier makes a hamming noise when connecting to the speaker terminals of your amplifier, connect both of the GND (ground) terminals on your amplifier and this unit using commercially available grounding wire as shown in fig. A . Connecting the power cable Plug the supplied power cable into the AC IN of this unit after all other connections are complete, and then plug the power cable to an AC outlet. POWER When your amplifier has no GND (ground) terminal, connect to the screw that fastens the top cover of your amplifier as shown in fig. B . ON OFF To the AC outlet L MONO L R R INPUT 3 INPUT 2 R R A OUTPUT TO SPEAKERS FROM AMPLIFIER INPUT 1 Notes • Do not use other power cables. Use the provided cable. Use of other power cables may result in fire hazard or electrical shock. L L B Note When connecting the GND (ground) terminal, make sure the power cables of the amplifier and this unit are not plugged into the AC outlet. 12 En • Do not plug the power cable into the AC outlet of your amplifier. Doing so may create distorted sounds or turn off the power of your amplifier. USING THIS UNIT Adjusting the sound balance Before using this unit, adjust the volume balance of this unit to obtain the optimum volume and tone balance between the front speakers and this unit by following the procedures below. Remote control 6 Rear panel POWER 1 POWER STANDBY SLEEP ON OFF MEMORY 1 HIGH CUT Normally, set the volume to a level where you can obtain a little more bass effect than when this unit is not used. y If you cannot obtain the desired response, repeat steps 5 and 6. PHASE B.A.S.S. PRESET 2 3 VOLUME 1 2,6 7 1 Set POWER switch on the rear panel of this unit to the ON position, and then press POWER to turn on this unit. The STANDBY/ON indicator lights up green. SUBW STANDBY /ON 2 Press VOLUME to set the volume level of this unit to the minimum (0). 3 Turn on the power of all other components. 4 Play back a source containing lowfrequency components and adjust the volume level of your amplifier to the desired listening level. Press VOLUME to increase the volume gradually to adjust the volume balance between the front speaker and this unit. Press PHASE to select the regular or reverse mode. Normally, set it to the reverse mode. If you cannot obtain the desired response, set it to the regular mode. 8 Press B.A.S.S. to select a mode that is suitable for the source. 1: WIDE When a movie source is played, the low- frequency effects are enhanced so that you can enjoy more powerful sound. 2: NORMAL When a music or movie etc. source is played, you can enjoy natural bass sounds. 3: NARROW When an ordinary music source is played, the excessive low-frequency signals are cut off to make the sound clearer. Set the tone control on your amplifier to the center position. 5 Press HIGH CUT / to adjust to the position where the desired response can be obtained. Normally, set the position to a level slightly higher than the minimum frequency of the front speaker. * To find out the minimum frequency of the front speaker, refer to the owner’s manual of the front speaker. 13 En USING THIS UNIT Storing the sound balance settings You can store up to 3 sets of your favorite settings (volume, high-cut, phase and B.A.S.S. setting) in this unit. Remote control Front panel STANDBY/ON indicator STANDBY 1 PHASE MEMORY 1 PRESET 2 3 1 2 STANDBY /ON 2 VOLUME 1 2 Note If the power is cut for more than one week, the setting is cleared. 3 PRESET Setting the sleep timer STANDBY /ON VOLUME 10 0 H-CUT 1 10 0 HIGH CUT 3 B.A.S.S. PHASE Hz 40 1 3 1 B.A.S.S. Even if you turn off this unit by using the POWER switch on the rear panel, this unit recalls the last setting when the power is turned back on (Last memory function). SUBWOOFER SYSTEM Soavo-900SW SLEEP Hz POWER ■Memory back-up 1 If you set the sleep timer, this unit automatically turns to the standby mode after 120 minutes. POWER STANDBY B.A.S.S. SLEEP SLEEP PHASE MEMORY 1 ■Storing the setting HIGH CUT PRESET 2 3 VOLUME In the following procedure, PRESET 1 is used as an example. 1 2 Adjust the sound balance between the volume, high cut, phase and B.A.S.S. (see page 13). Press MEMORY. The PRESET indicators on the front panel flash. -900SW 3 1 2 3 PRESET 3 Press PRESET 1. The PRESET 1 indicator lights up. The current setting is stored as PRESET 1. y • In step 3, pressing a stored number overwrites the old setting. • While the VOLUME control or the H-CUT control is rotating by pressing a PRESET, pressing another PRESET is ineffective. ■Recalling a setting Press PRESET you want to recall (1, 2 or 3). 14 En Press SLEEP. The color of the STANDBY/ON indicator changes to orange. SUBW STANDBY /ON Pressing SLEEP again cancels the sleep timer. USING THIS UNIT Operating the power of this unit using the remote control of your amplifier * This function is available only for Yamaha amplifiers that meet the following conditions: – The amplifier was released in 2005 or later. – The remote control of the amplifier has two different buttons for STANDBY and ON. Note When the AMP ID library code of the remote control has been changed, this function may not work. Rear panel Front panel POWER ■Canceling 1 Set POWER switch on the rear panel to the OFF position. 2 Set POWER switch to the ON position while pressing and holding STANDBY/ON switch on the front panel. Continue holding down STANDBY/ON switch for 3 seconds or longer. After the STANDBY/ON indicator flashes 2 times, the setting is completed. SUBWOOFER SYSTEM Soavo-900SW 1 ON STANDBY /ON PHASE 2 3 1 B.A.S.S. 2 3 SUBW PRESET OFF 40 0H z STANDBY /ON 10 10 0 Hz H-CUT POWER switch VOLUME STANDBY/ON switch STANDBY /ON Note Place this unit within the operating range of the remote control of the amplifier. If you place this unit far away from the amplifier, you may not be able to operate this unit with the remote control. ■Setting 1 Set POWER switch on the rear panel to the OFF position. 2 Set POWER switch to the ON position while pressing and holding STANDBY/ON switch on the front panel. Continue holding down STANDBY/ON switch for 3 seconds or longer. After the STANDBY/ON indicator flashes 4 times, the setting is completed. SUBW STANDBY /ON 15 En USING THIS UNIT Frequency response Frequency response of this unit dB H-CUT 140 Hz 90 80 70 60 50 40 20 50 100 200 500Hz Frequency response graph* The figures below show the optimum adjustment of each control and the frequency response when this subwoofer is combined with a typical front speaker system. ■ EX.1 When combined with a 10 cm or 13 cm (3-15/16” or 5-2/16”) acoustic suspension, 2 way system front speakers If you are using Soavo-1 speakers as front speakers, use the following example as a reference when adjusting settings. dB (H-CUT) (VOLUME) (PHASE) OOFER SYSTEM S 90 Soavo-900SW (H-CUT 60 - 70 Hz) 80 1 0 14 Hz 0H 40 z 70 PHASE 10 VOLUME H-CUT reverse mode (Green) 60 50 40 20 Front speaker 50 100 200 500Hz Frequency response graph* ■ EX.2 When combined with a 20 cm or 25 cm (7-14/16” or 9-13/16”) acoustic suspension, 2 way system front speakers dB (H-CUT) (VOLUME) (PHASE) OOFER SYSTEM S 90 80 Soavo-900SW (H-CUT 50 - 60Hz) H-CUT 10 0 Hz 14 0H 40 z 1 PHASE 70 VOLUME reverse mode (Green) 60 Front speaker 50 40 20 50 100 200 500Hz Frequency response graph* * These diagrams do not depict actual frequency response characteristics accurately. 16 En Advanced Yamaha Active Servo Technology II In 1988, Yamaha brought to the speaker systems utilizing YST (Yamaha Active Servo Technology) to give powerful, high quality bass reproduction. This technology uses a direct connection between the amplifier and speaker, allowing accurate signal transmission and precise speaker control. As this technology uses speaker units controlled by the negative impedance drive of the amplifier and resonance generated between the cabinet capacity volume and port, it creates more resonant energy (the “air woofer” concept) than the standard bass reflex method. This allows for bass reproduction from much smaller cabinets than was previously possible. Yamaha’s newly developed Advanced YST II adds many refinements to Yamaha Active Servo Technology, allowing better control of the forces driving the amplifier and speaker. From the amplifier’s point of view, the speaker impedance changes depending on the sound frequency. Yamaha developed a new circuit design combining negative-impedance and constant-current drives, which provides a more stable performance and clear bass reproduction without any murkiness. Signals of low amplitude Advanced impedance Converter Cabinet Active Servo Processing Amplifier High-amplitude bass sound Signals Port Air woofer (Helmholtz resonator) 17 En TROUBLESHOOTING Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions given below do not help, disconnect the power cord and contact your authorized Yamaha dealer or service center. Problem Cause Remedy Power is not supplied even though the STANDBY/ON switch is pressed. The power plug is not securely connected. Connect it securely. The POWER switch is set to the OFF position. Set the POWER switch to the ON position. No sound. The volume is set to the minimum (0). Raise the volume. Speaker cables are not connected securely. Connect them securely. The signals from the amplifier are too low. Increase the volume of the amplifier or the component connected to the amplifier. The signal from the subwoofer output terminal of the amplifier is not output. Check the speaker mode setting on the amplifier. Speaker cables are not connected correctly. Connect them correctly, that is L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Setting of the phase is not proper. Set the phase to the other position. A source sound with few bass frequencies is being played. Play a source sound with bass frequencies. Set the H-CUT to a higher position. It is influenced by standing waves. Reposition this unit or break up the parallel surface by placing bookshelves etc. along the walls. Wrong distance or angle. Use the remote control within a maximum range of 6 m and no more then 30 degrees off-axis from the front panel. Direct sunlight or lighting from an inverter type of fluorescent lamp etc. is striking the remote control sensor of this unit. Reposition this unit. The batteries are weak. Replace all batteries. This unit is not turned on with the remote control of the amplifier. (when setting “Operating the power of this unit using the remote control of your amplifier”) Wrong distance or angle. Place this unit within the operating range of the remote control of the amplifier. The household breaker goes off. This unit consumes much electricity when a high level signal is input to this unit. Turn down the volume on the amplifier etc. connected to this unit or cut off the power of other unused equipment. Sound level is too low. The remote control does not work. Notes • When an excessive level of signal is input to this unit for 5 to 15 minutes, the POWER indicator starts flashing to alarm you of the danger of damaging the power amplifier and speaker of this unit. If the signal input lasts for 5 minutes more, this unit turns into the standby mode automatically. • When an enormous amount of signal is input, the power of this unit is turned off immediately. To turn on this unit again, press STANDBY/ON switch on the front panel. 18 En SPECIFICATIONS Type .... Advanced Yamaha Active Servo Technology II Power Consumption ........................................... 180 W Driver ...................................... 25 cm (10”) cone woofer Magnetic shielding type Standby Power Consumption ............................. 0.5 W Amplifier Output (100 Hz, 4 ohms, 10% T.H.D) ............................................................................... 600 W Dimensions (W x H x D) .......................................... 410 mm x 457 mm x 462 mm (16-1/8” x 17” x 18-3/16”) Frequency Response ............................. 18 Hz - 160 Hz Weight ............................................. 32 kg (70 lbs. 9 oz.) Power Supply U.S.A. and Canada models ............. AC 120 V, 60 Hz U.K. and Europe models ................ AC 230 V, 50 Hz Australia model .............................. AC 240 V, 50 Hz Asia and General models ....................... AC 110/120/220/230-240 V, 50/60 Hz Korea model ................................... AC 220 V, 60 Hz China model ................................... AC 220 V, 50 Hz Please note that all specifications are subject to change without notice. 19 En ©2006 YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA All rights reserved. Printed in Indonesia WH59770
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Yamaha 900SW Manual de usuario

Categoría
Amplificadores de audio
Tipo
Manual de usuario
Este manual también es adecuado para