Rhino-Rack Pioneer Platform Guía de instalación
- Tipo
- Guía de instalación
Page 1 of 15
PIONEER ALLOY TRAY (flat pack)
Rhino-Rack,
22 Hanson Pl, Eastern Creek
NSW 2766, Australia
(02) 8846 1900
rhinorack.com.au
Document No: R2445
Issue No: 03
Issue Date: 11/03/2021
Important:
1. Check the Rhino-Rack website to ensure you have the latest issue of these instructions.
2. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations.
3. Check the contents of kit before commencing fitment and report any discrepancies.
4. Place these instructions in the vehicle’s glove box after installation is complete.
5. These instructions must be followed for warranty to be upheld.
Fit Time: 1 hour
rhinorack.page.
link/FitMyCar
Page 2 of 16
Instructions - Instrucciones
Off Road: Any driven path taken that does not contain a surface protection layer (tar/bitumen).
Vehicle Load Limit: Total permissible weight attached to the roof of the car. This is inclusive of the weight of the roof rack system.
System Load Limit: Total permissible weight allowed on top, and attached to roof racks whilst the vehicle is in motion.
Torque Settings
Unless stated otherwise in these instructions, all fasteners should be set to the following torque settings - M6: 4-5Nm (3-4lbs/ft),
M8: 8-10Nm (6-7.5lbs/ft) and M10: 16-18Nm (12-13lbs/ft).
Warning
• Check part number/ or kit is correct for use with your vehicle.
• Do not attempt to fit the rack system to your vehicle unless you fully understand these fitting instructions. Please direct any
questions regarding fitting to the dealer from where the roof racks were purchased.
• Although the system is tested and approved to AS1235-2000 / ISO 11154, off-road conditions can be much more rigorous.
Extreme care must be taken in off road conditions.
• Roof racks must be removed when vehicle is put through an automatic car wash.
• With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if the item
transported is rigidly fixed at points on both the cabin and canopy. Instead, rigidly fix to either the cabin roofracks or the canopy
roofracks.
• Always ensure you fasten your load securely.
• Use only non-stretch fastening ropes or straps to attach cargo to your load.
Note for Dealers and Fitters
It is your responsibility to ensure these fitting instructions are given to the end user or client. These instructions remain the property
of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
• All bolted connections should be checked after driving a short distance when you first install your roof racks.
• All bolted connections should be checked again at regular intervals (weekly is recommended, depending on road conditions,
usage, loads and distances travelled).
• All bolted connections should be checked each time they are re-fitted.
In service maintenance checks
Carrying Capacity
Max system load capacity (incl. system weight), refer to Pioneer fit sheet.
Check your vehicle owners hand book for vehicle maximum carrying capacity. Please ensure you use the vehicle
manufacturers maximum roof allowance if it is lower than the figure listed in this instruction.
Load must be evenly distributed over the system.
rhinorack.page.link/FitMyCar
Document No: R2536
Issue No: 1
Issue Date: 25-Jun-20
These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be
used or changed for any other purpose than intended.
NOTES FOR DEALERS / FITTERS
It is your responsibility to ensure these fitting instructions
are given to the end user or client.
*CHECK YOUR VEHICLE OWNERS HAND BOOK FOR VEHICLE MAXIMUM CARRYING CAPACITY. PLEASE ENSURE YOU USE THE VEHICLE
MANUFACTURERS MAXIMUM ROOF ALLOWANCE IF IT IS LOWER THAN THE FIGURE LISTED IN THIS INSTRUCTION.
VEHICLE LOAD LIMIT (VLL)
(kg / lbs)
SYSTEM WEIGHT (SW)
(kg / lbs) ON-ROAD CARGO ALLOW. (OR) OFF-ROAD CARGO ALLOW. (OFR)
Up to 100 / 220.5 * 19 / 41.2 OR = VLL - SW OFR = OR / 1.5
BAR NO. A B C D E F G
DIMENSION (CM) -45.2 0 45.2
SPACERS REQ’D
CONNECTOR RCL RCL
REAR
FRONT
+- BA C
UNDERBAR SPACING
REGION AUS NZ USA CA SA UK EU ZA
AVAILABILITY 3 3 222222
RUNNING DATES 02/15 - 02/15 - - - - - - -
IMPORTANT NOTES RCP68-BK required. Fixed point factory mount. -
VEHICLE PIONEER SIZE CONNECTOR HEIGHT ADDED (mm / in)
KIA Carnival Van Flush Rail 5 dr 52100 RCL 120.0 / 4.7
Page 1 of 1
PIONEER VEHICLE FITTING INFORMATION
rhinorack.com.au
EXAMPLE ONLY
Page 3 of 16
Instructions - Instrucciones
Terracería: Cualquier camino en donde se pueda manejar que no contenga una capa protectora en la superficie (alquitrán/betún/
pavimento).
Límite de carga del vehículo: Peso total permisible agregado a el techo del vehículo (esto incluye el peso del sistema de las barras
del techo).
Límite de carga del sistema: Peso total permisible permitido en el techo, agregado a las barras del techo mientras el vehículo está
en movimiento.
Configuración de esfuerzo de torsión:
A menos de que este escrito lo contrario en estas instrucciones, todos los sujetadores debenser configurados con las siguientes
instrucciones
M6:4-5Nm (3-4 lbs/ft)
M8: 8-10Nm (6-7.5 lbs/ft) y
M10: 16-18 Nm (12-13 lbs/ft)
Precaución
• Asegurarse que el número de parte/equipo es el correcto para usarse en su vehículo.
• No intente instalar el equipo de barras de techo en su vehículo a menos que entienda
completamente las instrucciones de instalación. Por favor dirija cualquier pregunta
relacionada con la instalación a el vendedor autorizado en donde adquirió el equipo.
• A pesar de que el sistema ha sido examinado y aprobado por AS1235-2000/ISO 11154,
las condiciones de terracería pueden ser mucho más rigurosas. Se debe tener extremo
cuidado en las condiciones de la terracería.
• Las barras del techo deben ser removidas antes de que el vehículo entre en un sistema
de auto-lavado.
• En vehículos de utilería, la cabina y la cubierta de el vehículo se mueven
independientemente. Las barras del techo y el vehículo pueden ser dañados si el
artículo que se está transportando esta rígidamente fijo en los puntos de ambos cabina
y cubierta. En lugar, se debe fijar solamente a uno de los dos (cabina o cubierta).
• Siempre asegúrese que sujetar su carga de forma segura.
• Solamente debe de usar sujetadores no elásticos para asegurar su carga a las barras del
techo.
Revisiones de mantenimiento de servicio:
• Todas las conexiones de tornillos deben ser revisadas después de manejar una corta
distancia cuando se instala por primera vez las barras del techo.
• Todas las conexiones con tornillos deben ser revisadas nuevamente en intervalos
regulares (se recomienda semanalmente, dependiendo de las condiciones del camino, el
uso, las cargas y las distancias recorridas).
• Todas las conexiones con tornillos deben ser revisadas cada vez que se reparan.
Nota para Vendedores e Instaladores:
• Es su responsabilidad asegurarse que las instrucciones de instalación sean dadas a el
cliente o quien reciba el producto. Estas instrucciones son propiedad.
Capacidad de Carga
Capacidad máxima de carga para el Sistema (incluye el Sistema de peso). Revise el manual del propietario de su vehículo para la
capacidad máxima de carga. Por favor asegúrese de solo usar la cantidad máxima de carga para el techo permitida por el manu-
facturero, si es menor que lo enlistado en la siguiente tabla. La carga debe de ser distribuida equivalentemente sobre el Sistema.
rhinorack.page.link/FitMyCar
Document No: R2536
Issue No: 1
Issue Date: 25-Jun-20
NOTES FOR DEALERS / FITTERS
It is
y
our res
p
onsibilit
y
to ensure these fittin
g
instructions
*CHECK YOUR VEHICLE OWNERS HAND BOOK FOR VEHICLE MAXIMUM CARRYING CAPACITY. PLEASE ENSURE YOU USE THE VEHICLE
MANUFACTURERS MAXIMUM ROOF ALLOWANCE IF IT IS LOWER THAN THE FIGURE LISTED IN THIS INSTRUCTION.
VEHICLE LOAD LIMIT (VLL)
(kg / lbs)
SYSTEM WEIGHT (SW)
(kg / lbs) ON-ROAD CARGO ALLOW. (OR) OFF-ROAD CARGO ALLOW. (OFR)
Up to 100 / 220.5 * 19 / 41.2 OR = VLL - SW OFR = OR / 1.5
BAR NO. A B C D E F G
DIMENSION (CM) -45.2 0 45.2
SPACERS REQ’D
CONNECTOR RCL RCL
REAR
FRONT
+- BA C
UNDERBAR SPACING
REGION AUS NZ USA CA SA UK EU ZA
AVAILABILITY 3 3 222222
RUNNING DATES 02/15 - 02/15 - - - - - - -
IMPORTANT NOTES RCP68-BK required. Fixed point factory mount. -
VEHICLE PIONEER SIZE CONNECTOR HEIGHT ADDED (mm / in)
KIA Carnival Van Flush Rail 5 dr 52100 RCL 120.0 / 4.7
PIONEER VEHICLE FITTING INFORMATION
Page 4 of 16
Instructions - Instrucciones
GH
Tool Set
Torque Tool
8mm Socket Phillips Bit
x2
Ex2
F
G H
Platform # L x W
(mm)
L x W
(inches) GH I JKLM
52100 1528 x1236 60' x 49' 4 3 52 52 12 16 6
52101 1528 x 1376 60' x 54' 5 3 62 62 12 16 6
52102 1928 x1236 76' x 49' 4 5 76 76 12 16 6
52103 1928 x 1376 76' x 54' 5 5 90 90 12 16 6
52104 2128 x 1426 84' x 56' 5 5 90 90 12 16 N/A
52105 2728 x 1465 107' x 58' 5 6 104 104 12 16 N/A
52107 2128 x1236 84' x 49' 4 5 76 76 12 16 N/A
52108 1828 x 1426 72' x 56' 5 5 90 90 12 16 N/A
52109 1328 x1236 52' x 49' 4 3 52 52 12 16 N/A
52110 1328 x 1376 52' x 54' 5 3 62 62 12 16 N/A
52111 1328 x 1426 52' x 56' 5 3 62 62 12 16 N/A
52112 928 x 1426 37' x 56' 5 2 48 48 12 16 N/A
52113 1528 x 1426 60' x 56' 5 5 90 90 12 16 N/A
52114 1228 x 952 48' x 37' 3 1 22 22 12 16 N/A
52115 1478 x 1184 58' x 47' 4 1 28 28 12 16 N/A
52119 2528 x 1586 100' x 62' 5 6 104 104 12 16 N/A
52120 1528 x 1586 60' x 62' 5 3 62 62 12 16 N/A
52121 1228 x 1426 48' x 56' 5 3 62 62 12 16 N/A
x2
Cx2
D
x2
Ax2
B
x1
N
x1
O
x1
P
Tools required:
Herramientas necesarias:
T1 - Phillips head screwdriver.
T2 - Power drill.
1
Page 5 of 16
Instructions - Instrucciones
x2
x4 x16
x3 x12
x6 x24
x5 x20
L
F
H I IH
H I IH
F
Page 6 of 16
Instructions - Instrucciones
2
x2
A
x2
C
C
C
A
A
F
L
1-1.5Nm
1.1LB/FT
T1
CA
Page 7 of 16
Instructions - Instrucciones
3
4
E
O
T2
K
K
K
E
1: 2: 3:
O
T2
LB D
3-4NM
2-3LB/FT
E
Page 8 of 16
Instructions - Instrucciones
5
x3 x10 x4 x5 x6x12 x14 x16
IIII
I I I I
G
G
G G
I
I
G
EEEE H H H H
Page 9 of 16
Instructions - Instrucciones
6
7
8
G
I
E
G
E
Page 10 of 16
Instructions - Instrucciones
(A)
(B)
10
9
11 - Align the bolts ( )
- Alinear perno ( )
CLICK!
I
G
E
N
P
J
J
6-8NM
4-6LB/FT
I
I
Page 11 of 16
Instructions - Instrucciones
Document No: R2536
Issue No: 1
Issue Date: 25-Jun-20
These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be
used or changed for any other purpose than intended.
NOTES FOR DEALERS / FITTERS
It is your responsibility to ensure these fitting instructions
are given to the end user or client.
*CHECK YOUR VEHICLE OWNERS HAND BOOK FOR VEHICLE MAXIMUM CARRYING CAPACITY. PLEASE ENSURE YOU USE THE VEHICLE
MANUFACTURERS MAXIMUM ROOF ALLOWANCE IF IT IS LOWER THAN THE FIGURE LISTED IN THIS INSTRUCTION.
VEHICLE LOAD LIMIT (VLL)
(kg / lbs)
SYSTEM WEIGHT (SW)
(kg / lbs) ON-ROAD CARGO ALLOW. (OR) OFF-ROAD CARGO ALLOW. (OFR)
Up to 100 / 220.5 * 19 / 41.2 OR = VLL - SW OFR = OR / 1.5
BAR NO. A B C D E F G
DIMENSION (CM) -45.2 0 45.2
SPACERS REQ’D
CONNECTOR RCL RCL
REAR
FRONT
+- BA C
UNDERBAR SPACING
REGION AUS NZ USA CA SA UK EU ZA
AVAILABILITY 3 3 222222
RUNNING DATES 02/15 - 02/15 - - - - - - -
IMPORTANT NOTES RCP68-BK required. Fixed point factory mount. -
VEHICLE PIONEER SIZE CONNECTOR HEIGHT ADDED (mm / in)
KIA Carnival Van Flush Rail 5 dr 52100 RCL 120.0 / 4.7
Page 1 of 1
PIONEER VEHICLE FITTING INFORMATION
rhinorack.com.au
EXAMPLE ONLY
Instructions
12
13a
G H
I
H
rhinorack.page.link/FitMyCar
Bar 1, 2, 3
Bar 1
Bar 2
Bar 3
Page 12 of 16
Instructions - Instrucciones
3010 15 20 25 35 4020
13b
-EXAMPLE
-EJEMPLO
CLICK!
14
6-8NM
4-6LB/FT
J
J
Docu
m
e
nt
No
:R2
536
Issue
N
o
:
1
I
ssue
D
ate:
2
5-Jun-
20
T
hese instructions remain the
p
ro
p
ert
y
of Rhino-Rack Australia Pt
y
. Ltd. and ma
y
not be
u
sed or chan
g
ed for any other purpose than intended
.
N
OTES FOR DEALERS
/
FITTER
S
I
t
i
s your respons
i
b
i
l
i
ty to ensure these
fi
tt
i
n
g
i
nstruct
i
ons
a
re
g
iven to the end user or client
.
*
C
HE
C
K Y
O
UR VEHI
C
LE
O
WNER
S
HAND B
OO
K F
O
R VEHI
C
LE MAXIMUM
C
ARRYIN
G
C
APA
C
ITY. PLEA
S
E EN
S
URE Y
O
U U
S
E THE VEHI
C
LE
MANUFA
C
TURER
S
MAXIMUM R
OO
F ALL
O
WAN
C
E IF IT I
S
L
O
WER THAN THE FI
G
URE LI
S
TED IN THI
S
IN
S
TRU
C
TI
O
N
.
VEHICLE LOAD LIMIT
(
VLL
)
(
kg / lbs
)
SYSTEM WEIGHT
(
SW
)
(
kg / lbs
)
ON-ROAD CARGO ALLOW. (OR)
O
FF-ROAD CARGO ALLOW. (OFR)
Up
to 1
00
/
220
.5
*
19
/
41.2
O
R = VLL -
S
W
O
FR = OR / 1.5
D
S
PA
C
ER
S
RE
Q
’D
CO
NNE
C
T
OR
R
CL
RC
L
U
NDERBAR
S
PA
C
IN
G
RE
G
I
O
N
AUS
N
Z
US
A
C
A
S
A
U
K E
U
Z
A
A
VAILABILITY
3
3
2
2
2
2
2
2
RU
NNIN
G
DATE
S
0
2
/
15
-
02
/
15 - - - - - - -
IMP
O
RTANT N
O
TE
S
RCP68-BK re
q
uired. Fixed
p
oint factor
y
mount. -
VEHI
C
LE
P
I
O
NEER
S
IZE
CO
NNE
C
T
O
R
H
EIGHT ADDED
(
mm / in
)
KIA
C
arnival
Va
nFl
us
h Rail
5
d
r
5
21
00
R
C
L12
0
.
0
/
4.7
P
a
g
e 1 of 1
PI
O
NEER VEHI
C
LE FITTIN
G
INF
O
RMATI
ON
rh
i
norack.com.a
u
EXAMPLE ONLY
Page 13 of 16
Instructions - Instrucciones
- For Wiring
- Para el cableado
Note
- Cut out window
- Ventana
cortada
- Drill Wiring
window
- Taladrar
ventana de
cableado
- Wire your switch
- Conecta tu inter-
ruptor
A C
B D
A C
B D
Page 14 of 16
Instructions - Instrucciones
(=) (=)
RLT600, RCL/RCH,
RL leg variants.
SXB
RL legs variants require
VA-FK1.
RL piernas requieren
VA-FK1.
15
16
17 18
Page 15 of 16
Instructions - Instrucciones
19
SP308 =
20 Backbone
21
SP309 =
x4
x6
-Platform dependant.
-Dependiente de la
plataforma.
4-5NM
3-4LB/FT
10-12NM
7-9LB/FT
Page 16 of 16
Instructions - Instrucciones
(=) (=)
Note
PIONEER ALLOY TRAY (assembled)
Rhino-Rack, 22 Hanson Pl, Eastern Creek
NSW 2766, Australia
(02) 8846 1900
rhinorack.com.au
Document No: R1812
Issue No: 02
Issue Date: 23/03/2020
Important:
1. Check the Rhino-Rack website to ensure you have the latest issue of these instructions.
2. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations.
3. Check the contents of kit before commencing fitment and report any discrepancies.
4. Place these instructions in the vehicle’s glove box after installation is complete.
5. These instructions must be followed for warranty to be upheld.
Fit Time: 1 hour
rhinorack.page.
link/FitMyCar
22
Document No: R2536
Issue No: 1
Issue Date: 25-Jun-20
These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be
used or changed for any other purpose than intended.
NOTES FOR DEALERS / FITTERS
It is your responsibility to ensure these fitting instructions
are given to the end user or client.
*CHECK YOUR VEHICLE OWNERS HAND BOOK FOR VEHICLE MAXIMUM CARRYING CAPACITY. PLEASE ENSURE YOU USE THE VEHICLE
MANUFACTURERS MAXIMUM ROOF ALLOWANCE IF IT IS LOWER THAN THE FIGURE LISTED IN THIS INSTRUCTION.
VEHICLE LOAD LIMIT (VLL)
(kg / lbs)
SYSTEM WEIGHT (SW)
(kg / lbs) ON-ROAD CARGO ALLOW. (OR) OFF-ROAD CARGO ALLOW. (OFR)
Up to 100 / 220.5 * 19 / 41.2 OR = VLL - SW OFR = OR / 1.5
BAR NO. A B C D E F G
DIMENSION (CM) -45.2 0 45.2
SPACERS REQ’D
CONNECTOR RCL RCL
REAR
FRONT
+- BA C
UNDERBAR SPACING
REGION AUS NZ USA CA SA UK EU ZA
AVAILABILITY 3 3 222222
RUNNING DATES 02/15 - 02/15 - - - - - - -
IMPORTANT NOTES RCP68-BK required. Fixed point factory mount. -
VEHICLE PIONEER SIZE CONNECTOR HEIGHT ADDED (mm / in)
KIA Carnival Van Flush Rail 5 dr 52100 RCL 120.0 / 4.7
Page 1 of 1
PIONEER VEHICLE FITTING INFORMATION
rhinorack.com.au
15-20NM
11-15LB/FT
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
