Hampton Bay 21908 Guía del usuario

Marca: Hampton Bay

Modelo: 21908

Categoría: Ventiladores domésticos

Tipo: Guía del usuario

Installation

INSTALLATION AND OPERATION

SMART WI-FI REMOTE CONTROL

Safety Information

Warranty

CAUTION: Incorrect wire

connections will damage

this receiver.

The supplier warrants the remote control and receiver to be free from defects in

workmanship and material present at time of shipment from the factory for a period of

one year after the date of purchase by the original purchaser. We agree to correct such

defects without charge or at our option replace with a comparable or superior model if

the product is returned. To obtain warranty service, you must present a copy of the

receipt as proof of purchase. All costs of removing and reinstalling the product are your

responsibility. Damage to any part such as by accident or misuse or improper installation

or by afxing any accessories, is not covered by this warranty. Servicing performed by

unauthorized persons shall render the warranty invalid. There is no other express warranty.

Home Depot hereby disclaims any and all warranties, including but not limited to those of

merchantability and tness for a particular purpose to the extent permitted by law. The

duration of any implied warranty which cannot be disclaimed is limited to the time period

as specied in the express warranty. Some states do not allow a limitation on how long an

implied warranty lasts, so the above limitation may not apply to you. The retailer shall not

be liable for incidental, consequential, or special damages arising out of or in connection

with product use or performance except as may otherwise be accorded by law. Some

states do not allow the exclusion of incidental or consequential damages, so the above

exclusion or limitation may not apply to you. This warranty gives specic legal rights, and

you may also have other rights which vary from state to state. This warranty supersedes all

prior warranties. Shipping costs for any return of product as part of a claim on the warranty

must be paid by the customer.

Contact the Customer Service Team at 1-877-592-5233 or visit HomeDepot.com/hubspace.

Pre-Installation

Step

ladder

Part Description Quantity

A Receiver 1

B Remote control 1

CWire connecting nut 5

D AAA battery (1.5V) 2

E Silicone rubber plug 1

F Wall cradle 1

G Wall cradle screw 2

H Plastic anchor 2

I Rubber isolated pad 2

PACKAGE CONTENTS

IMPORTANT: This product and/

or components are governed by

one or more of the following U.S.

Patents: 5,947,436; 5,988,580;

6,010,110; 6,046,416, 6,210,117

and other patents pending.

NOTE: The frequencies on your receiver and hand unit have been preset

at the factory. Before installing the receiver, make sure the dip switches

on the receiver and hand unit are set to the same frequency. The dip

switches on the hand unit are located inside the battery compartment.

Setting the code on the remote control

Application Set-Up

• Remove the remote control (B)

battery cover by pressing firmly

on the arrow and sliding the

cover off.

• Slide the dip switches (ZZ) to

your choice of either up or down.

The factory setting is up.

• Slide the dip switches (ZZ) on

the receiver (H) to the same

position as set on the remote

control (B).

• Install two 1.5V batteries

(included).

• Replace the battery cover on the

remote control (B).

• Insert the silicone rubber

stopper (E) into the hole on the

receiver (A) to cover the dip

switches.

1Operating the remote control

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modications not expressly approved by the grantee of this device could void the user’s

authority to operate the equipment.

FCC ID: 2AQZU-18016

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Item #1006 022 993

Model #76278

CAUTION: To reduce the risk

of re or injury, do not use this

product in conjunction with any

variable (rheostat) wall control.

NOTE: The battery will weaken

with age and should be

replaced before leaking takes

place as this will damage

the hand unit. Dispose of the

used battery properly, keep

the battery out of the reach of

children.

WARNING: To avoid possible

electrical shock, turn the

electricity off at the main

fuse box before wiring. If you

feel you do not have enough

electrical wiring experience,

contact a licensed electrician.

3Installing the receiver

WARNING: To reduce the risk of re or electric shock, remember to

disconnect power. The electrical wiring must meet all local and national

electrical code requirements. The electrical source and fan must be 110/120

volt, 60Hz. Do not use this product in conjunction with any variable wall

control. Incorrect wire connection can damage this receiver.

CAUTION: If fan or house wires are a different color, have this unit installed by a

licensed electrician.

CAUTION: Do not install in a damp location or immerse in water (for indoor use

only). Do not pull on or cut leads shorter. Do not drop or bump the unit.

Installation (continued)

NOTE: You must set ceiling fan to high speed and light kit (if any) to the

on position using the pull chains (if applicable) before operating remote

control.

NOTE: For better performance with the WIFI system, the WIFI antenna must

be mounted to the ceiling outside of the fan’s ceiling canopy.

• Position the house supply wires (AAA) to one side of the slide-on mounting

bracket; position the fan wires (BBB) to the opposite side.

• Insert the narrow end of the receiver (as shown, flat side towards the

ceiling) into the slide-on mounting bracket until it rests on top of the ball/

downrod assembly.

Installation (continued)

4Wiring the receiver to the household wiring

WARNING: Each wire nut supplied with this fan is designed to accept up

to one 12-gauge house wire and two wires from the fan. If you have larger

than 12-gauge house wiring or more than one house wire to connect to

the fan wiring, consult an electrician for the proper size wire nuts to use.

• Spread the wires apart so that the green and white wires are on one side of the

outlet box and the black wire is on the other side.

• Connect the green fan wires to the household ground wire (this may be a green

or bare wire) using a wire connecting nut (C) supplied by your fan.

• Connect the receiver black (or red) wire to the household black (hot) wire using

a wire connecting nut (C).

• Connect the receiver white wire to the household white wire (neutral) wire

using a wire connecting nut (C).

• Secure each wire connecting nut using electrical tape.

WARNING: To avoid possible electrical shock, turn the electricity off at the

main fuse box before wiring. If you feel you do not have enough electrical

wiring knowledge or experience, contact a licensed electrician.

Wiring the fan to the receiver

• Connect the fan motor white wire

to the receiver white wire using a

wire connecting nut (C).

• Connect the fan motor black wire

to the receiver black wire using a

wire connecting nut (C).

• Connect the fan motor blue wire

to the receiver blue wire using a

wire connecting nut (C).

• Secure each wire connecting nut

using electrical tape.

• Turn the wire connecting nut (C)

upward and push the wiring into

the outlet box (MM).

IMPORTANT: Use the wire connecting nuts (C) supplied with your remote.

The wire connecting nut (C) for the ground/green wire is supplied with the

fan. Secure the connectors with electrical tape and ensure there are no

loose strands or connections.

Operating Your Remote Control

Mounting the transmitter to the wall

• Slide the screw cover plate up to remove it from the wall cradle (F).

• Position the wall cradle (F) in the desired position and attach it to the wall using the

included wall cradle screws (G).

• Slide the screw cover plate back onto the wall cradle to conceal the screws.

Wire

cutter

Electrical tape

Phillips

screwdriver

Installation (continued)

Read and save these instructions

1. The power supply to the remote control

receiver should be connected through a

mains switch, i.e. existing wall switch.

2. Disconnect from power supply at breaker

box or wall switch before working on

remote control receiver or ceiling fan.

3. Install receiver into the mounting

bracket/ canopy of the fan to ensure

proper protection.

4. This unit is to be used for the control of

ceiling fan and in a AC110/120V 60Hz

power supply only.

5. Do not install in damp locations or

immerse in water. (For indoor use only.)

6. Do not pull on or cut leads shorter.

7. Do not drop or bump the unit.

8. Do not mix old and new batteries.

9. Do not mix alkaline, standard (carbon-

zinc), or rechargeable (ni-cad, ni-mh,

etc.) batteries.

Controller model: TR240B

WIFI antenna mount

outside of the canopy

BBB

AAA

Black

Green (or Bare)

Green

Outlet Box

Receiver

Antenna

White

Receiver (B)

C (x3)

DIP

Antenna

WIFI

Screw cover plate

Power ON/OFF: Press and release the power

button to turn the fan and light on or off.

Fan speed: LEDs on the fan speed button will

illuminate to the corresponding speed.

Press and release 1 time: turns the fan speed

to 4.

Press and release 2 times: turns the fan

speed to 3.

Press and release 3 times: turns the fan

speed to 2.

Press and release 4 times: turns the fan

speed to 1.

Press and release 5 times: turns the fan off.

Light ON/OFF:

Press and release the button to turn the light

on or off.

Press and hold the button to activate the

dimmer function.

Comfort Breeze: Press the button to enable

Comfort Breeze; this will change your fan

randomly, simulating a relaxing breeze. To

cancel this features press fan speed button or

power button.

Timer:

While the fan is on press 1 time-turns on a 2 hour run timer.

While the fan is on press 2 times-turns on a 4 hour run timer.

While the fan is on press 3 times-turns on a 8 hour run timer.

□Download the Hubspace™ app from the App Store or

the Google Play Store to your mobile device.

□Launch the app.

□To register, enter your email address and a password.

Or, login if you already have an account.

□Bluetooth access is required for device setup.

Getting started

□Hubspace only shows WiFi networks that your device can use. Check your network

only if an option does not appear during set up.

□This Hubspace device requires a 2.4GHz Wi-Fi channel.

□Most routers provide a 2.4 GHz WiFi channel.

□If you do not see your Wi-Fi network name when you attempt to connect your

device, please check your router settings.

Verify your network

□In the Hubspace app, tap the plus sign in the upper right corner.

□Scan your product’s QR code. You can nd a copy of the QR code on the device itself

and in the Quick Start Guide.

Scan problem?

If the QR code cannot be scanned for some reason, you can enter the code manually.

Tap Enter Code and follow the instructions.

□Connect your device to power and follow the instructions on screen.

(For lighting and fan products only)

Add a device

If you are unable to access the QR code for your light, you can put it into discovery mode

with the following sequence:

□Switch the device off and on 5 times. The light will pulse to show that it can now be

discovered.

□In the Hubspace app, tap the plus sign in the upper right corner and follow the

instructions to discover devices. More than one device can be added at a time using

this method.

Set up your voice assistant

□In the Hubspace app, tap the Hubspace button.

□Select the Integrations tab, choose your voice assistant and follow the instructions.

NOTE: For more information on smart remote set up, please refer to the quick start

guide located in the remote pack.

Questions, problems, missing parts? Before returning to the store,

call Hubspace Customer Service

8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday

1-877-592-5233

HOMEDEPOT.COM/HUBSPACE

We appreciate the trust and condence you have placed in Hampton Bay through

the purchase of this remote control. We strive to continually create quality

products designed to enhance your home. Visit us online to see our full line of

products available for your home improvement needs.

Thank you for choosing Hampton Bay!

NOTE: The switch marked “O/D” controls the dimming function of the

lights. If you are using non-dimmable bulbs, use a ballpoint pen or small

screwdriver to set the switch to “O” to disable the dimming function.

If you are using dimmable bulbs, set the switch to “D” to enable the

dimming function.

NOTE: The battery will weaken with age and should be replaced before

leaking takes place, as battery leakage damages the hand unit. Dispose

of the used battery properly and keep the battery out of the reach of

children.

Outlet box

in the ceiling

(MM)

Green

1 2 3 4

ON DIP

Blue Black White

C (x3)

Problem Solution

My hubspace device is not

connecting to Wi-Fi. Make sure your device is connected to a power source.

Your Internet connection or Wi-Fi network may be down.

My device cannot nd any

Wi-Fi networks. Make sure you have a 2.4GHz capable Wi-Fi network within

range of the device you are trying to add.

My device is in a location that

does not have Wi-Fi. Can I still

use it with the Hubspace app?

Yes:

Use the app on a phone with an Internet connection like LTE.

The phone must be within Bluetooth range of your Hubspace

device.

I cannot nd the QR code. Look for it where other stickers are on the product. A copy of

the QR code is also included in your device’s documentation.

The QR code has become

damaged. How do I add the

device?

Under the QR code are numbers. You can enter those in

manually instead of scanning the code.

How do I reset the device? Remove the device from your account, then add it back.

Devices also reset when they transfer to a new account.

A device is on another

account. How do I transfer it? Scan the QR code and it will transfer to your account.

My device is ofine for long

periods of time. Make sure your Wi-Fi signal strength is sufcient. You may

need to move your router, use mesh Wi-Fi, or Wi-Fi extenders.

The device is on and I scanned

the QR code, but the app

cannot connect to it.

Turn off Bluetooth on your phone and turn it back on. Then,

scan the QR code.

Can I scan the same QR code

to add multiple products? No. Each product has a unique QR code.

Troubleshooting

NOTE: Plastic anchors (H) are included for extra support. The included screws (G)

are designed to screw easily into the wall. If you would like a more permanent

or secure hold, install the wall anchors (H) prior to attaching the wall cradle to

the wall.

Installation (continued)

TOOLS REQUIRED

• Loosen the two screws provided with the outlet box; insert two rubber

isolatedpads (I) between the mounting bracket and the outlet box; firmly

tightened the two screws.

2Installing the rubber isolated pads

Voice Commands

The Smart Wi-Fi Remote Control works with Alexa and Google Assistant.

This section lists some of the voice commands you can use. To view these and other

commands, go to http://hubspaceconnect.com/.

When you

want to...

Ask Alexa to... Ask Google to...

Turn on the fan

only.

… turn on <device name> fan

power.

… turn on <device name> fan power.

Turn off the fan

only.

… turn off <device name> fan

power.

… turn off <device name> fan power.

Turn on the light

only.

… turn on <device name> light

power.

… turn on <device name> light power.

Turn off the light

only.

… turn off <device name> light

power.

… turn off <device name> light power.

Change the

brightness.

... Set <device name> brightness

to 75%.

… Set <device name> light to 25%.

… Make <device name> dimmer.

… Make <device name> brighter.

… Dim <device name>.

… Brighten <device name>.

… Dim <group name>.

… Brighten <group name>.

... Set <device name> brightness

to 75%.

… Set <device name> light to 25%.

… Brighten <device name>.

… Dim <device name>.

… Brighten <room name>.

… Dim <room name>.

Change the White

Temperature.

… Change <device name> to Cool

White.

… Change <device name> to Warm

White.

… Change <device name> to

Daylight White.

… Change <device name> to White.

… Change <device name> to Ivory.

… Change <device name> to Daylight.

… Change <device name> to Cool

White.

… Change <device name> to Warm

White.

... Change <device name> to

Incandescent.

Change the fan

speed.

… Set <device name> speed to

fastest.

… Set <device name> speed to fast.

… Set <device name> speed to

medium.

… Set <device name> speed to

slow.

… Increase <device name> speed.

… Decrease <device name> speed.

… Set <device name> speed to

fastest.

… Set <device name> speed to fast.

… Set <device name> speed to

medium.

… Set <device name> speed to slow.

… Increase <device name> speed.

… Decrease <device name> speed.

Turn on Comfort

Breeze.

… Turn on Comfort Breeze on

… Turn on Comfort Breeze on <device

name>

Alexa

Outlet box

Mounting

Bracket

1 2 3 4

D O

12 3 4

D O

1 2 3 4

ON DIP

IMPORTANT: Use the wire connecting nuts (C) supplied with your remote.

The wire connecting nut (C) for the ground/green wire is supplied with the

fan. Secure the connectors with electrical tape and ensure there are no

loose strands or connections.

Responsible Party - U.S. Contact Information: King of Fans, Inc

1951 NW 22nd Street, Fort Lauderdale, FL 33311, (954) 484-7500

Item #1003 202 212, 1002 175 786

Model #57264, 57268

UL Model #52-COPY

USE AND CARE GUIDE

HOLLY SPRINGS 52-INCH CEILING FAN

Questions, problems, missing parts? Before returning to the store,

call Hampton Bay Customer Service

8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday

1-855-HD-HAMPTON

HAMPTONBAY.COM

THANK YOU

We appreciate the trust and condence you have placed in Hampton Bay through the purchase of this ceiling fan. We strive to continually create

quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.

Thank you for choosing Hampton Bay!

To view an instructional video on how to install this product:

1. Go to www.homedepot.com and enter either the Item or Model number, found in the top

right corner of the cover of this instruction manual, in the search ÿeld.

2. Click on your product from the list of search results and click on the video link in the

“Product Overview” section.

Table of Contents ................................................................2

Safety Information ...............................................................2

Warranty ............................................................................... 3

Pre-Installation ....................................................................3

Installation ............................................................................6

Assembly ..............................................................................7

Operation ...........................................................................14

Care and Cleaning ............................................................. 15

Troubleshooting .................................................................15

1. To reduce the risk of electric shock, ensure the electricity has

been turned off at the circuit breaker or fuse box before you

begin.

2. All wiring must be in accordance with the National Electrical

Code ANSI/NFPA 70-1999 and local electrical codes. Electrical

installation should be performed by a qualified licensed

electrician.

3. The outlet box and support structure must be securely mounted

and capable of reliably supporting 35 lbs. (15.9 kg). Use only UL

Listed outlet boxes marked “Acceptable for Fan Support of 35 lbs.

(15.9 kg) or less.”

4. The fan must be mounted with a minimum of 7 ft. (2.1 m) clearance

from the trailing edge of the blades to the oor.

5. Do not operate the reversing switch while the fan blades are in

motion. You must turn the fan off and stop the blades before you

reverse the blade direction.

6. Do not place objects in the path of the blades.

7. To avoid personal injury or damage to the fan and other items,

use caution when working around or cleaning the fan.

8. Electrical diagrams are for reference only. Light kits that are not

packed with the fan must be UL-listed and marked suitable for

use with the model fan you are installing. Switches must be UL

General Use Switches. Refer to the instructions packaged with

the light kits and switches for proper assembly.

9. After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into the outlet box. The

wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box.

10. All setscrews must be checked and retightened where

necessary before installation.

WARNING: To reduce the risk of personal injury, do not

bend the blade brackets (also referred to as anges) during

assembly or after installation. Do not insert objects in the

path of the blades.

WARNING: Remove the rubber motor stops on the bottom of

the fan before installing the blades or testing the motor.

WARNING: To reduce the risk of re or electric shock, do

not use this fan with any solid-state speed control device.

WARNING: To avoid possible electrical shock, turn the

electricity off at the main fuse box before wiring. If you

feel you do not have enough electrical wiring knowledge or

experience, contact a licensed electrician.

WARNING: Electrical diagrams are for reference only.

Optional use of any light kit shall be UL-listed and marked

suitable for use with this fan.

WARNING: To reduce the risk of re, electric shock, or

personal injury, mount to outlet box marked “Acceptable

for fan support of 35 lbs. (15.9 kg) or less,” and use the

screws provided with the outlet box.

Safety Information

Table of Contents

READ AND SAVE THESE INSTRUCTIONS

HAMPTONBAY.COM

Please contact 1-855-HD-HAMPTON for further assistance.

Pre-Installation

Warranty

The supplier warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime

after the date of purchase by the original purchaser. The supplier also warrants that all other fan parts, excluding any glass or acrylic blades, to be

free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the

original purchaser. We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is

returned. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product

are your responsibility. Damage to any part, such as by accident, misuse, improper installation, or by afxing any accessories, is not covered by

this warranty. Because of varying climatic conditions this warranty does not cover any changes in brass nish, including rusting, pitting, corroding,

tarnishing, or peeling. Brass nishes of this type give their longest useful life when protected from varying weather conditions. A certain amount of

“wobble” is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the warranty invalid. There is

no other express warranty. Hampton Bay hereby disclaims any and all warranties, including but not limited to those of merchantability and tness

for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time

period as specied in the express warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation

may not apply to you. The retailer shall not be liable for incidental, consequential, or special damages arising out of or in connection with product

use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages,

so the above exclusion or limitation may not apply to you. This warranty gives specic legal rights, and you may also have other rights which vary

from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must

be paid by the customer.

Contact the Customer Service Team at 1-855-HD-HAMPTON or visit www.HamptonBay.com.

SPECIFICATIONS

TOOLS REQUIRED

Size Speed Volts Amps Watts RPM CFM Net

Weight

Gross

Weight Cube Feet

52 in.

Low

Medium

High

120

0.21

0.35

0.51

105

165

1717

2885

4356

18.74 lb

(8.5 kg)

22.49 lb

(10.2 kg) 2.19 cu.ft.

NOTE: These are approximate measures. They do not

include the amps and wattage used by the light kit.

Phillips

screwdriver

Flat blade

screwdriver

Adjustable

wrench

Electrical

tape

Wire

cutter /

stripper

Step ladder

Part Description Quantity

AA Pull chain 2

BB Hanger pin 1

CC Locking pin 1

Part Description Quantity

DD Extra blade bracket screw 1

EE Plastic plug (to be used for fan without

light kit)

FF Wire connecting nut 3

Pre-Installation (continued)

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

AA BB CC

DD EE FF

HAMPTONBAY.COM

Please contact 1-855-HD-HAMPTON for further assistance.

Part Description Quantity

A Slide-on mounting bracket

(inside canopy)

B Ball/downrod assembly 1

C Canopy 1

D Fan-motor assembly 1

E Light kit tter assembly 1

Part Description Quantity

F Blade 5

G Blade bracket (with pre-installed

screws)

H Glass bowl 1

I LED bulbs (9 Watt Max.) 3

IMPORTANT: This product and/or components are

governed by one or more of the following U.S. Patents:

5,947,436; 5,988,580; 6,010,110; 6,046,416, 6,210,117

and other patents pending.

Pre-Installation (continued)

PACKAGE CONTENTS

Installation

MOUNTING OPTIONS

WARNING: To reduce the risk of re, electric shock

or personal injury, mount to an outlet box marked

“Acceptable for fan support of 35 lbs. (15.9 kg) or less,”

and use the screws provided with the outlet box. An

outlet box commonly used for the support of lighting

xtures may not be acceptable for fan support and may

need to be replaced. If in doubt, consult a qualied

electrician.

If your ceiling fan does not have an existing UL-listed mounting

box, then install one using the following instructions:

□Disconnect the power by removing the fuses or turning off

the circuit breakers.

□Secure the outlet box directly to the building structure.

Use the appropriate fasteners and materials. The outlet box

and its bracing must be able to fully support the weight

of the moving fan (at least 35 lbs.). Do not use a plastic

outlet box.

The illustrations below show three different ways to mount the

outlet box.

If the canopy (C) touches the ball/downrod assembly (B), then remove

the decorative canopy bottom cover and turn the canopy (C) 180°

before attaching the canopy (C) to the mounting plate.

To hang your fan where there is an existing xture but no ceiling joist,

you may need an installation hanger bar as shown above (available at

any Home Depot store).

NOTE: You may need a longer downrod to maintain

proper blade clearance when installing on a steep, sloped

ceiling. The maximum angle allowable is 20° away from

horizontal.

Outlet Box

Recessed

Outlet

Box

Provide Strong

Support

Ceiling

Mounting

Plate

Outlet Box

Hanger Bar

HAMPTONBAY.COM

Please contact 1-855-HD-HAMPTON for further assistance.

Assembly - Standard Ceiling Mount

Routing the wires

Assembling the fan

Preparing for standard mounting

□Loosen, but do not remove, the setscrews (II) on the collar

on top of the fan-motor assembly (D).

□Align the holes at the bottom of the ball/downrod assembly

(B) with the holes in the collar on top of the fan-motor

assembly (D).

□Carefully insert the hanger pin (BB) through the holes in

the collar and ball/downrod assembly (B). Be careful not to

jam the hanger pin (BB) against the wiring inside the ball/

downrod assembly (B).

□Insert the locking pin (CC) through the hole near the end of

the hanger pin (BB) until it snaps into its locked position.

□Re-tighten the setscrews (II) on the collar on top of the fan-

motor assembly (D).

□Remove the canopy bottom cover (HH) from the canopy

unlocks.

□Loosen the two canopy screws (GG) located in the bottom

of the mounting bracket, and turn the canopy counter-

clockwise to remove the mounting bracket (A) from the

canopy (C).

□Route the wires exiting the top of the fan motor

assembly (D) through the center of the canopy bottom

cover (HH).

□Make sure the opening of the canopy (C) is on top and

insert the ball/downrod (B) through the canopy (C).

□Route the wires exiting the top of the fan motor

assembly (D) through the downrod as shown.

WARNING: Failure to properly install the locking

pin (CC) could result in the fan becoming loose and

possibly falling.

BB CC

Assembly - Hanging the Fan

Attaching the fan to the electrical

box

□Pass the 120-Volt supply wires through the center hole in the

slide-on mounting bracket (A).

□Install the slide-on mounting bracket (A) on the outlet box by

sliding the slide-on mounting bracket (A) over the two screws (JJ)

provided with the outlet box. If necessary, use leveling washers

(not included) between the slide-on mounting bracket (A) and

the outlet box. The at side of the slide-on mounting bracket (A)

should face toward the outlet box, as shown.

□Securely tighten the two mounting screws (JJ).

WARNING: To reduce the risk of re, electric shock or

personal injury, mount to an outlet box marked “Acceptable

for fan support of 35 lbs. (15.9 kg) or less,” and use the

screws provided with the outlet box.

Hanging the fan

2 □Carefully lift the fan-motor assembly (D) up to the slide-on

mounting bracket (A).

□Insert the ball portion of the ball/downrod assembly into the

socket of the slide-on mounting bracket (A).

□Turn the ball/downrod assembly clockwise until it is seated

with the tab of the slide-on mounting bracket (A) aligned with

the slot in the ball.

NOTE: The mounting bracket (A) is designed to slide into

place on an outlet box with the outlet box screws (JJ).

JJ JJ

HAMPTONBAY.COM

Please contact 1-855-HD-HAMPTON for further assistance.

Assembly - Hanging the Fan (continued)

Making the electrical connections

IMPORTANT: Use the plastic wire connectors (FF) supplied with

your fan. Secure the connectors with electrical tape and ensure

there are no loose strands or connections.

WARNING: Each wire nut supplied with this fan is designed to

accept up to one 12-gauge house wire and two wires from the

fan. If you have larger than 12-gauge house wiring or more

than one house wire to connect to the fan wiring, consult an

electrician for the proper size wire nuts to use.

□The fan comes with 54 in. lead wires for use with an extended

ball/downrod assembly. If using the 4.5 in. ball/downrod

assembly (B) provided, you can cut the lead wires to your

desired length (no shorter than 12 in.) This will make extra

room in the canopy (C). If you do not wish to cut the wires, you

will need to neatly wrap them.

NOTE: The fan comes with 54 in. lead wires for use with an

extended ball/downrod assembly. If using the 4.5 in. ball/downrod

assembly (B) provided, you can cut the lead wires to your desired

length (no shorter than 12 in.).

WARNING: Remove the rubber motor stops on the bottom of the

fan before installing the blades or testing the motor. Please refer to remote installation

instructions at the beginning of

this manual.

Assembly - Hanging the Fan (continued)

Mounting the fan-motor assembly

(standard mount)

4 5

Wrapping the extra wire

□Gently wrap the excess wire around the mounting bracket.

□Secure with electrical tape.

NOTE: Follow this step ONLY if you did not cut the extra

length off from the wires coming from the ceiling fan.

□Align the locking slots of canopy (C) with the two screws (GG)

and alignment post (QQ) in the mounting bracket (A).

□Push up the canopy (C) and turn clockwise until the alignment

post (QQ) engages the round hole and the screws (GG) engage

to the key slots.

□Firmly tighten the two mounting screws (GG).

□Install the decorative bottom cover (HH) by aligning the covers

slots with screws in the bottom of the canopy (C). Rotate the

bottom cover clockwise to lock in place.

WARNING: When using the standard ball/downrod mounting, the

tab in the ring at the bottom of the mounting bracket must rest in

the groove of the hanger ball. Failure to properly seat the tab in

the groove could cause damage to the wiring.

HAMPTONBAY.COM

Please contact 1-855-HD-HAMPTON for further assistance.

Assembly - Attaching the Fan Blades

Fastening the blade brackets to

the motor

□Fasten the blade brackets (G) to the fan-motor assembly

(D) by inserting the alignment post into the slot on the

bottom of the motor and tightening the pre-installed blade

bracket screws (LL).

□Repeat this step for the remaining blade assemblies.

WARNING: Remove the rubber motor stops on the bottom of

the fan before installing the blades or testing the motor.

NOTE: Your fan features revolutionary advancements for quick

and easy blade installation, including an alignment post and

captive blade bracket screws.

Attaching the blades to the blade

brackets

□Mount the fan blade (F) to the blade bracket (G) by aligning the

three key-slot holes in the blade (F) with the three posts on the

top of the blade bracket (G).

□Hold the blade (F) with both hands close to the blade bracket

(G) down rmly. Ensure the key-slot holes are properly seated

on the blade bracket (G) posts.

□While still holding the blade (F) down with both hands, rmly

slide the blade (F) until it engages in the locking mechanism

(UU). Make sure the locking mechanism (UU) at the rear of the

blade bracket (G) springs upward and butts against the edge of

the blade (F), indicating a secure connection.

□Visually inspect the top of the blade bracket (G) to ensure the

locking mechanism is securely in place.

□Repeat this procedure for the remaining blades (F).

NOTE: Your fan blades are reversible. Select the blade side nish

which best accentuates your decor.

Assembly - Attaching the Lights

Attaching the light kit tter assembly

□Remove and save the three light kit mounting screws (MM) on

the black bracket below the fan-motor assembly (D).

□Connect the wires from the light kit tter assembly (E) to the

wires from the fan motor assembly (D) by connecting the

molded adaptor plugs together. Carefully tuck all wires and

splices into the switch cup.

□Align the three holes in the black bracket below fan motor

assembly (D) with the three holes in the switch cup of the light

kit tter assembly (E). Position the light kit tter assembly (E)

and re-install the three screws (MM) that were removed in rst

step to secure the light kit tter assembly (E).

CAUTION: To reduce the risk of electric shock, disconnect

the electrical supply circuit to the fan before installing the

light xture.

NOTE: Notice the location of the fan’s slide switch. This is

the switch used to change the fan’s directional rotation.

For more information on the operation of this switch, see

Operating Your Fan on page 14.

IMPORTANT: It is critical to attach the switch cup using the

quick connector. The fan will not operate unless the light kit

is connected to the fan.

Installing the bulbs and glass bowl

□Remove the nial (PP) and the bottom cover (OO) from the

threaded nipple of the light kit tter assembly (E).

□With the power off, install the three LED bulbs (I) by screwing

them into the light bulb sockets.

□Pass the fan switch chain (SS) through the hole in the bowl cap

(QQ) of the light kit.

□Position the glass bowl (H) over the threaded nipple and raise

the glass bowl up to the bowl cap, re-install the bottom cover

(OO) over the threaded nipple and pass the fan switch chain

through the offset hole in the bottom cover.

□Re-install the nial (PP) over the threaded nipple and direct the

light pull chain through the hole of the nial (PP), and tighten the

nial (PP) securely.

□Attach the pull chain extensions (AA) provided to the light pull

chain and fan pull chain.

CAUTION: Make sure the power is off before attaching or

removing the glass bowl.

WARNING: Allow the glass bowl to cool completely before

removing.

CAUTION: Be sure that the fan switch pull chain does not make

contact with the light bulbs. If necessary, reposition the light kit

to avoid the fan switch pull chain from touching the light bulbs.

HAMPTONBAY.COM

Please contact 1-855-HD-HAMPTON for further assistance.

Assembly - Assembling the Fan Without the Light Kit

Assembling the fan without the

light kit

□Remove the three light kit mounting screws (MM) on the

black bracket below the fan-motor assembly (D).

□In order to use the fan without the light kit, remove the

switch cup (WW) from the top of the light kit tter assembly

(E) by removing the center hex nut (NN) inside the switch

cup (WW), and then thread the switch cup (WW) off the

threaded nipple on the top of the light kit tter assembly (E).

□Press the plastic plug (EE) (provided) into the center hole of

the switch cup (WW).

□Connect the quick connect couplers. (The fan will not start

without this connection).

□Position the switch cup (WW) onto the black bracket and

reinstall the light kit mounting screws (MM).

IMPORTANT: It is critical to attach the switch cup using the

quick connector. The fan will not operate unless the light kit

is connected to the fan.

Turn on the power and check the operation of the fan. The fan pull

chain controls the fan speed as follows:

1 pull - High, 2 pulls - Medium, 3 pulls - Low, 4 pulls - off

The appropriate speed settings for warm or cool weather depends on

factors such as the room size, ceiling height, and number of fans.

The slide switch (YY) controls the direction of the blades: forward

(switch left) or reverse (switch right).

A. Warm weather - (Forward) A downward airow creates a cooling

effect. This allows you to set your air conditioner on a higher setting

without affecting your comfort.

B. Cool weather - (Reverse) An upward airow moves warm air off of the

ceiling. This allows you to set your heating unit on a lower setting

without affecting your comfort.

NOTE: Wait for the fan to stop before reversing the direction of the

blade rotation.

Operation

OPERATING YOUR FAN A. Warm Weather

B. Cool Weather

HAMPTONBAY.COM

Please contact 1-855-HD-HAMPTON for further assistance.

Troubleshooting

Problem Solution

The fan will not start. □Check the main and branch circuit fuses or breakers.

□Check the line wire connections to the fan and switch wire connections in the switch housing.

The fan is noisy. □Ensure all motor housing screws are snug.

□Ensure the screws that attach the fan blade bracket to the motor hub are tight.

□Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing.

□Allow a 24-hour “breaking in” period. Most noises associated with a new fan disappear during this time.

□If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light

bulbs are also secure.

□Ensure the canopy is a short distance from the ceiling. It should not touch the ceiling.

□Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.

The fan wobbles. □Check that all blade and blade arm screws are secure.

□Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the

ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the

ceiling. Measure this distance. Rotate the fan until the next blade is positioned for measurement. Repeat for each

blade. Any measurement deviation should be within 1/8 in. Run the fan for ten minutes. If the fan continues to

wobble please contact Customer Service and a balancing kit will be sent to you at no charge.

□Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade

attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.

□Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage

the motor or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the nish. The

plating is sealed with a lacquer to minimize discoloration or tarnishing.

□You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a

light application of shoe polish.

□You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.

WARNING: Make sure the power is off before cleaning

your fan.

Care and Cleaning

Questions, problems, missing parts? Before returning to the store,

call Hampton Bay Customer Service

8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST Saturday

1-855-HD-HAMPTON

HAMPTONBAY.COM

Retain this manual for future use.

Instalación

INSTALACIÓN Y OPERACIÓN

CONTROL REMOTO WI-FI INTELIGENTE

Información de seguridad

Garantía

PRECAUCIÓN: Conectar el

cableado de manera incorrecta

dañará este receptor.

El proveedor garantiza que el control remoto y el receptor no presentan defectos de fabricación ni

de materiales, al momento en que es enviado desde la fábrica, por un período de un año a partir de

la fecha de adquisición por el comprador original. Si el producto es devuelto, aceptamos reparar

sus defectos sin cargo alguno o, a nuestra discreción, reemplazarlo por modelo similar o superior.

Para obtener servicio de garantía tiene que presentar una copia del recibo como comprobante de

compra. Todos los costos de retiro y reinstalación del producto correrán por cuenta del cliente. No

están cubiertos bajo esta garantía los daños a ninguna de las piezas como resultado de accidentes,

instalación o uso incorrectos o por instalación de cualquier accesorio. Cualquier servicio prestado

por personal no autorizado invalidará la garantía. No hay ninguna otra garantía expresa. Por este

medio The Home Depot queda exento de todas y cada una de las garantías, incluyendo, pero sin

limitarse a, aquellas de comercialización e idoneidad para un n particular, en el alcance permitido

por la ley. La duración de cualquier garantía implícita que no pueda exonerarse se limita al plazo

especicado en la garantía explícita. Algunos estados no permiten limitaciones sobre la duración

de las garantías implícitas, así que es posible que la limitación anterior no se aplique en su caso.

El minorista no será responsable por daños incidentales, emergentes ni especiales derivados

del uso o funcionamiento del producto, excepto en los casos en los que la ley así lo disponga.

Algunos estados no permiten excluir ni limitar daños directos o indirectos, así que es posible que

la limitación o exclusión anterior no se aplique en este caso. Esta garantía otorga derechos legales

especiales al cliente y es posible que también goce de otros derechos que pueden variar según el

estado. Esta garantía sustituye a todas las garantías anteriores. Los costos de envío en cualquier

devolución de productos como parte de un reclamo de garantía corren por cuenta del cliente.

Comuníquese con el Equipo de Servicio al Cliente al teléfono 1-877-592-5233 o visite

HomeDepot.com/hubspace.

Preinstalación

Escalera

de tijera

Pieza

parte

Descripción Cantidad

A Receptor 1

B Control remoto 1

CTuerca para conectar

cables

DBatería AAA (1.5 V) 2

E Enchufe de goma de

silicona

F Soporte de pared 1

G Tornillo de soporte

de pared

H Anclaje plástico 2

I Almohadilla aislante

de goma

CONTENIDO DEL PAQUETE

IMPORTANTE: Este producto y/o

sus componentes están protegidos

por una o más de las siguientes

patentes de los EE. UU.: 5,947,436;

5,988,580; 6,010,110; 6,046,416,

6,210,117 y otras patentes

pendientes.

NOTA: Las frecuencias del receptor y de la unidad de mano han sido

preconfiguradas de fábrica. Antes de instalar el receptor, asegura que los

interruptores en línea del receptor y de la unidad de mano estén en la misma

frecuencia. Los interruptores en línea en la unidad de mano están ubicados

dentro del compartimiento de la batería.

Cómo congurar el código del control remoto

Conguración fácil de la aplicación

• Quita la cubierta de la batería del

control remoto (B) presionando

con firmeza sobre la flecha y

deslizando la cubierta hasta

liberarla.

• Desliza los interruptores en línea

(ZZ) hacia arriba o abajo según

prefieras. La configuración de

fábrica es hacia arriba.

• Desliza los interruptores en línea

(ZZ) sobre el receptor (H) hacia

la misma posición fijada para el

control remoto (B).

• Instala dos baterías de 1.5 V

(incluidas).

• Coloca de nuevo la cubierta en el

control remoto (B).

• Inserta el tapón de goma de

silicona (E) en el orificio del

receptor (A) para cubrir los

interruptores.

1Cómo operar el control remoto

Este equipo fue sometido a prueba y se determinó que cumple con los límites establecidos para un

dispositivo digital Clase B según la Parte 15 de las Normas FCC. Estos límites fueron establecidos para

dar protección razonable contra la interferencia dañina en uso residencial. Este equipo genera, consume y

puede irradiar energía de radiofrecuencia; si no se instala y usa de acuerdo con las instrucciones, puede

causar interferencia nociva a comunicaciones radiales. Sin embargo, no hay garantía de que no ocurrirá

interferencia en cierta instalación particular. Si este equipo causa interferencia perjudicial a la recepción

de radio o televisión, que puede determinarse encendiendo y apagando el equipo, se recomienda al usuario

tratar de corregir la interferencia con una o más de las siguientes medidas:

– Reorientar o reubicar la antena receptora.

– Incrementar la distancia entre los equipos y el receptor.

– Conectar el equipo a un tomacorriente en circuito distinto del receptor.

– Pedir asistencia al concesionario o a un técnico de radio/TV con experiencia.

PRECAUCIÓN:

Los cambios o modicaciones sin aprobación expresa del responsable de este dispositivo podrían anular

el derecho del usuario a operar el equipo.

ID de FCC: 2AQZU-18016

Este dispositivo cumple con la Parte 15 de las Normas FCC. Su operación está sujeta a las dos condiciones

siguientes: (1) Este dispositivo no debe causar interferencia dañina y (2) tiene que aceptar cualquier

interferencia recibida, incluyendo aquella que pudiera afectar su funcionamiento.

Artículo Núm. 1006 022 993

Modelo Núm. 76278

PRECAUCIÓN: Para reducir el

riesgo de incendio o lesiones,

no utilices este producto con

ningún control de pared variable

(reóstato).

NOTA: La batería se debilitará

con el tiempo y deberá ser

reemplazada antes de que se

produzca alguna fuga, ya que

esto dañará la unidad de mano.

Desecha bien la batería usada

y mantén toda batería fuera del

alcance de los niños.

ADVERTENCIA: Para evitar una

posible descarga eléctrica,

desconecta la electricidad en

la caja principal de fusibles

antes de realizar el cableado. Si

crees que no tienes suciente

experiencia en cableado

eléctrico, contacta a un

electricista con licencia.

3Cómo instalar el receptor

ADVERTENCIA: Para reducir el riesgo de incendio o de descarga eléctrica, recuerda

desconectar la electricidad. El cableado eléctrico tiene que cumplir todos los requisitos

de los códigos eléctricos nacionales y locales. La fuente de energía y el ventilador

tienen que ser de 110/120 V y 60 Hz. No utilizar este producto con ningún control

variable de pared. Conectar el cableado de manera incorrecta dañará este receptor.

PRECAUCIÓN: Si los cables del ventilador o del hogar son de color diferente, haz que

un electricista con licencia instale esta unidad.

PRECAUCIÓN: No instalar en lugares húmedos ni sumergir en agua (sólo para uso en

interiores). No hales ni recortes los cables terminales. No dejes caer ni golpees la unidad.

Instalación (continuación)

NOTA: Tienes que configurar el ventilador de techo en velocidad alta y el kit de

luces (si lo tiene) en la posición ON usando las cadenas de halar (si corresponde)

antes de operar el control remoto.

NOTA: Para mejor rendimiento con el sistema WIFI, la antena WIFI tiene que

montarse al cielo raso fuera de la cubierta del ventilador de techo.

• Coloca los cables de suministro del hogar (AAA) a un lado del soporte de montaje

deslizante; coloca los cables del ventilador (BBB) en el lado opuesto.

• Inserta el extremo angosto del receptor (como se muestra: el lado plano hacia

el techo) en el soporte de montaje deslizante hasta dejarlo apoyado en la parte

superior del conjunto de tubo bajante/esfera.

Instalación (continuación)

4Cómo cablear el receptor al cableado del hogar

ADVERTENCIA: Cada tuerca para cable suministrada con este ventilador está

diseñada para aceptar un cable doméstico de calibre 12 o menos y dos cables

del ventilador. Si tu cableado doméstico tiene calibre mayor de 12 o más de un

cable para conectar al cableado del ventilador, consulta a un electricista para

saber el tamaño adecuado de las tuercas a usar para los cables.

• Separa los cables de manera que los cables verde y blanco queden de un lado de la

caja eléctrica y el cable negro, del otro lado.

• Conecta los cables verdes del ventilador al cable con conexión a tierra de la casa

(este puede ser verde o pelado) con la tuerca de conexión de cables (C) suministrada.

• Conecta el cable negro (o rojo) del receptor al cable negro del hogar (positivo), usando

una tuerca de conexión de cables (C).

• Conecta el cable blanco del receptor al cable blanco del hogar (neutro), usando una

tuerca de conexión de cables (C).

• Asegura cada tuerca de conexión de cables con cinta de electricista.

ADVERTENCIA: Para evitar una posible descarga eléctrica, desconecta la

electricidad en la caja principal de fusibles antes de realizar el cableado.

En caso de no tener suficiente conocimiento o experiencia sobre cableado

eléctrico, contacta a un electricista certificado.

Cómo cablear el ventilador al receptor

• Conecta el cable blanco del motor

del ventilador al cable blanco del

receptor usando una tuerca de

conexión de cables (C).

• Conecta el cable negro del motor

del ventilador al cable negro del

receptor usando una tuerca de

conexión de cables (C).

• Conecta el cable azul del motor del

ventilador al cable azul del receptor

usando una tuerca de conexión de

cables (C).

• Asegura cada tuerca de conexión de

cables con cinta de electricista.

• Gira la tuerca de conexión de cables

dentro de la caja eléctrica (MM).

IMPORTANTE: Usa las tuercas de conexión de cables (C) que vienen con tu control

remoto. La tuerca de conexión del cable (C) para el cable de tierra / verde se

suministra con el ventilador. Sujeta los conectores con cinta de electricista y

asegúrate de que no haya conexiones ni cables sueltos.

Cómo usar el control remoto

Cómo montar el transmisor en la pared

• Desliza la placa de la cubierta de los tornillos hacia arriba para quitarla del soporte de pared (F).

• Coloca el soporte de pared (F) en la posición deseada y fíjalo a la pared con los tornillos del

soporte de pared incluidos (G).

• Desliza la placa de la cubierta de los tornillos nuevamente sobre el soporte de pared para

ocultar los tornillos.

CortacablesCinta de

electricista

Destornillador

Phillips

Instalación (continuación)

Lee y guarda estas instrucciones

1. El suministro de corriente al receptor de

control remoto debe conectarse a través de

un interruptor principal, i.e., un interruptor

de pared preexistente.

2. Desconectar el suministro de corriente en la

caja de cortacircuitos o en el interruptor de

pared antes de trabajar con el receptor de

control remoto o el ventilador de techo.

3. Instalar el receptor en el soporte de montaje

/ cubierta del ventilador para garantizar la

protección adecuada.

4. Esta unidad debe usarse solamente para

controlar ventiladores de techo en una fuente

de corriente de CA de 110/120 V y 60 Hz.

5. No instalar en lugares húmedos ni sumergir

en agua. (Sólo para uso en interiores).

6. No hales ni recortes los cables terminales.

7. No dejes caer ni golpees la unidad.

8. No mezclar baterías viejas y nuevas.

9. No mezclar baterías alcalinas, estándar

(carbón-cinc) ni recargables (Ni-Cad, Ni-Mh

y otras).

Modelo del controlador: TR240B

Antena WIFI montada

fuera de la cubierta

BBB

AAA

Negro

Verde (o pelado)

Verde

Caja eléctrica

Antena

receptora

Blanco

Receptor (A)

C (x3)

Antena

WIFI

Placa de cubierta de los tornillos

ENCENDIDO/APAGADO: Presiona y suelta el botón

para encender o apagar el ventilador y la luz.

Velocidad del ventilador: Las luces LED en el

botón de velocidad del ventilador indicarán la

velocidad correspondiente.

Presionar y soltar 1 vez: convierte la velocidad

del ventilador a 4.

Presionar y soltar 2 veces: convierte la velocidad

del ventilador a 3.

Presionar y soltar 3 veces: convierte la velocidad

del ventilador a 2.

Presionar y soltar 4 veces: convierte la velocidad

del ventilador a 1.

Presionar y soltar 5 veces: para apagar el

ventilador.

Encendido y apagado de luces (ON/OFF)

Presiona y suelta el botón para encender o

apagar la luz.

Presiona y mantén presionado el botón para

activar la función de regulación de intensidad

luminosa.

Comfort Breeze: Presiona el botón para activar

la función Comfort Breeze; esto hará que la

velocidad del ventilador cambie aleatoriamente,

imitando una brisa relajante. Para cancelar

esta función, presiona el botón de velocidad del

ventilador o el botón de encendido.

Temporizador:

Con el ventilador encendido, oprime el botón 1 vez para activar el

temporizador con 2 horas de funcionamiento.

Con el ventilador encendido, oprime el botón 2 veces para activar el

temporizador con 4 horas de funcionamiento.

Con el ventilador encendido, oprime el botón 3 veces para activar el

temporizador con 8 horas de funcionamiento.

□Descarga gratis la aplicación gratuita Hubspace™ en la

tienda de apps de Apple o Google Play a tu dispositivo móvil.

□Inicia la aplicación.

□Para registrarte, ingresa tu dirección de correo electrónico

y una contraseña. O inicia sesión si ya tienes una cuenta.

□Se requiere acceso a Bluetooth para congurar el dispositivo.

Comencemos

□Hubspace solo muestra las redes WiFi que su dispositivo puede usar. Verica tu red solo

si una opción no aparece durante la conguración.

□Este dispositivo Hubspace requiere un canal Wi-Fi de 2.4 GHz.

□La mayoría de los routers proporcionan un canal WiFi de 2.4 GHz.

□Si no ves el nombre de tu red Wi-Fi cuando intentes conectar tu dispositivo, verica la

conguración de tu router.

Verica tu red

□En la aplicación Hubspace, toca el signo “más” (+) en la esquina superior derecha.

□Escanea el código QR de tu producto. Puedes encontrar una copia del código QR en el

dispositivo y en la Guía de inicio rápido.

¿Problema de escaneo?

Si el código QR no se puede escanear por alguna razón, puedes ingresar el código

manualmente. Toca Ingresar código y sigue las instrucciones.

□Conecta tu dispositivo a la corriente y sigue las instrucciones en la pantalla.

(Solo para productos de iluminación y ventiladores)

Añade un dispositivo

Si no puedes acceder al código QR de tu luz, puedes ponerlo en modo de descubrimiento con la

siguiente secuencia:

□Apaga y enciende el dispositivo 5 veces. La luz parpadeará para mostrar que ahora se

puede descubrir.

□En la aplicación Hubspace, toca el signo “más” (+) en la esquina superior derecha y sigue

las instrucciones para descubrir los dispositivos. Se puede agregar más de un dispositivo a

la vez usando este método.

Congura tu asistente de voz

□En la aplicación Hubspace, toca el botón Hubspace.

□Selecciona la pestaña Integrations (Integraciones), elige tu asistente de voz y sigue las

instrucciones.

NOTA: Para obtener más información sobre la conguración del control remoto

inteligente, consulta la guía de inicio rápido que se encuentra en el paquete del control

remoto.

¿Preguntas, problemas, piezas faltantes? Antes de devolver a la tienda,

llama al Servicio al Cliente de Hubspace

entre 8:00 a.m. y 7:00 p.m. (hora del Este) de lunes a viernes,

y los sábados de 9:00 a.m. a 6:00 p.m. (hora del Este).

1-877-592-5233

HOMEDEPOT.COM/HUBSPACE

Apreciamos la conanza que has depositado en Hampton Bay al comprar este control

remoto. Nos esforzamos en crear continuamente productos de calidad diseñados para

mejorar tu hogar. Visítanos por Internet para ver nuestra línea completa de productos

disponibles a n de satisfacer tus necesidades de mejoras del hogar.

¡Gracias por elegir Hampton Bay!

NOTA: El interruptor marcado con “O/D” controla la función de regulación

de la intensidad de las luces. Si usas bombillas no regulables, emplea

un bolígrafo de punta redonda o un destornillador pequeño para fijar el

interruptor a la posición “O” a fin de desactivar la función de regulación de

intensidad. Si usas bombillas regulables, fija el interruptor en la posición “D”

para activar la función de regulación de intensidad.

NOTA: La batería se debilitará con el tiempo y deberá ser reemplazada antes

de que se produzca alguna fuga, ya que las fugas de las baterías dañarán la

unidad de mano. Desecha la batería adecuadamente y mantenla fuera del

alcance de los niños.

Caja eléctrica

en el techo

(MM)

Verde

Azul

Negro

Blanco

C (x3)

Problema Solución

Mi dispositivo hubspace no se

conecta a Wi-Fi.

Asegúrate de que tu dispositivo esté conectado a una fuente de alimentación.

Tu conexión a Internet o red Wi-Fi puede estar inactiva.

Mi dispositivo no puede encontrar

ninguna red Wi-Fi.

Asegúrate de tener una red Wi-Fi con capacidad de 2.4 GHz dentro del

alcance del dispositivo que está intentando agregar.

Mi dispositivo está en una ubicación

que no tiene Wi-Fi. ¿Puedo

seguir usándolo con la aplicación

Hubspace?

Sí:

Usa la aplicación en un teléfono con conexión a Internet como LTE.

El teléfono debe estar dentro del alcance de Bluetooth de tu dispositivo

Hubspace.

No encuentro el código QR. Búscalo donde haya otras etiquetas adhesivas en el producto. También se

incluye una copia del código QR en la documentación de tu dispositivo.

El código QR se ha dañado. ¿Cómo

añado el dispositivo?

Debajo del código QR hay números. Puedes ingresarlos manualmente en

lugar de escanear el código.

¿Cómo reinicio el dispositivo? Elimina el dispositivo de tu cuenta y luego vuelve a agregarlo. Los

dispositivos también se restablecen cuando se transeren a una nueva

cuenta.

Un dispositivo está en otra cuenta.

¿Cómo lo transero?

Escanea el código QR y se transferirá a tu cuenta.

Mi dispositivo está desconectado

durante largos períodos de tiempo.

Asegúrate de que la intensidad de la señal de tu Wi-Fi sea suciente.

Es posible que debas mover tu router, usar Wi-Fi de red o extensores

de Wi-Fi.

El dispositivo está encendido y

escaneé el código QR, pero la

aplicación no se puede conectar.

Apaga el Bluetooth en tu teléfono y vuelve a encenderlo. Luego, escanea

el código QR.

¿Puedo escanear el mismo código

QR para agregar varios productos?

No. Cada producto tiene un código QR único.

Solución de problemas

NOTA: Se incluyen anclajes de plástico (H) para soporte adicional. Los tornillos

incluidos (G) están diseñados para atornillarse fácilmente en la pared. Si deseas una

sujeción más permanente o segura, instala los anclajes de pared (H) antes de jar el

soporte de pared a la pared.

Instalación (continuación)

HERRAMIENTAS NECESARIAS

• Aflojar los dos tornillos incluidos con la caja eléctrica; insertar dos almohadillas

aislantes de goma (I) entre el soporte de montaje y la caja eléctrica; apretar

firmemente los dos tornillos.

2Cómo instalar las almohadillas aislantes de goma

Comandos de voz

El control remoto Wi-Fi inteligente funciona con Alexa y Google Assistant.

Esta sección enumera algunos de los comandos de voz que puedes utilizar. Para ver estos y

otros comandos, visita http: //hubspaceconnect.com/.

Cuando

quieras…

Pídele a Alexa… Pídele a Google...

Encender solo el

ventilador.

... Enciende el ventilador <nombre del

dispositivo>.

... Enciende el ventilador <nombre del

dispositivo>.

Apagar solo el

ventilador.

... Apaga el ventilador <nombre del

dispositivo>.

... Apaga el ventilador <nombre del

dispositivo>.

Encender sola la luz. ... Enciende la luz de <nombre del

dispositivo>.

... Enciende la luz de <nombre del

dispositivo>.

Apagar solo la luz. ... Apaga la luz de <nombre del dispositivo>. ... Apaga la luz de <nombre del dispositivo>.

Cambiar la

luminosidad.

... Congura la intensidad luminosa de

<nombre del dispositivo> al 75%.

...Congura la luz de <nombre del

dispositivo> al 25%.

… Reduce la intensidad de luz de <nombre

del dispositivo>.

… Aumenta la intensidad de luz de <nombre

del dispositivo>.

… Reduce la intensidad de luz de <nombre

del dispositivo>.

… Aumenta la intensidad de luz de <nombre

del dispositivo>.

… Reduce la intensidad de luz de <nombre

del grupo>.

… Aumenta la intensidad de luz de <nombre

del grupo>.

... Congura la intensidad luminosa de

<nombre del dispositivo> al 75%.

...Congura la luz de <nombre del dispositivo>

al 25%.

… Aumenta la intensidad de luz de <nombre

del dispositivo>.

… Reduce la intensidad de luz de <nombre

del dispositivo>.

… Aumenta la intensidad de luz de <nombre

de habitación>.

… Reduce la intensidad de luz de <nombre

de habitación>.

Cambiar la

temperatura blanca.

… Cambia <nombre del dispositivo> a

blanca fría.

… Cambia <nombre del dispositivo> a

blanca cálida.

… Cambia <nombre del dispositivo> a luz

natural blanca.

… Cambia <nombre del dispositivo> a

blanca.

… Cambia <nombre del dispositivo> a marl.

… Cambia <nombre del dispositivo> a luz

natural blanca.

… Cambia <nombre del dispositivo> a blanca fría.

… Cambia <nombre del dispositivo> a

blanca cálida.

... … Cambia <nombre del dispositivo> a

incandescente.

Cambiar la velocidad

del ventilador.