Samsung DV433GTGJWR Manual de usuario

Marca: Samsung

Modelo: DV433GTGJWR

Categoría: Secadoras

Tipo: Manual de usuario

Este manual también es adecuado para

Gas and Electric Dryer

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service or accessory

parts,

please register your product at or

contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

DV433*

This manual is made with 100% recycled paper.

DV433ETGJWR_A1_02836H-01_EN_20120713.indd 1DV433ETGJWR_A1_02836H-01_EN_20120713.indd 1 2012-07-13  1:07:022012-07-13  1:07:02

2_ Features

features

1. Extra Large Capacity

Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our

ultralarge 7.5 cu.ft. capacity dryer circulates more air through your clothes, drying them

faster, for a wrinkle-free result.

2. Steam Cycle

This cycle sprays a small amount of water into the dryer drum after several minutes of

tumbling with heat. It reduces bad odors from clothing that are difficult to remove when

washing with water, and also reduces wrinkles.

3. Sanitize Course

This course allows you to sanitize garments by permeating high temperature heat deep into

the fabric during the drying cycle. Use this course to keep your Bedding Plus and curtains

clean.

When selecting this cycle, 99.9% of certain bacteria is eliminated through high temperature

heat. Use this cycle for clothing, Bedding, towels, or other items needing sanitized. This

certification is conducted by NSF International, an independent third-party testing and

certification organization.

4. Various Drying Cycles & Fuzzy Logic Algorithm

Simply turn the Jog Dial to select one of the 13 automatic drying cycles, including normal,

heavy duty and Bedding Plus, or let the Fuzzy Logic Control measure the degree of

dampness and automatically set the drying time. Precision drying has never been easier than

with Samsung.

5. Time Saving

Our cycles are designed with you in mind. All our dryers are designed to dry your clothes in

less time... just 42 minutes! Giving you time for more important things in life.

6. Energy Saving

Samsung dryers are super energy efficient. You can dry up to 3.01 pounds of laundry with

1kWh. Also, both the large capacity and Fuzzy Logic Control save energy by automatically

drying your clothes the most efficient way.

7. Easy Reversible Door

Our dryers will fit just about anywhere and without a door conflict. The direction of our easy

reversible door can be changed with just four screws.

NSF Protocol P154

Sanitization Performance of

Residential Clothes Dryers

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec9:2DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec9:2 2012-07-13  1:07:422012-07-13  1:07:42

Features _3

8. Pedestal with Storage Drawers

An optional 15” pedestal is available to raise the dryer for easier loading and unloading. It

also offers a built-in storage drawer that can hold a 100 oz. bottle of detergent

9. Stacking (MODEL NO: SK-5A/XAA)

Samsung’s Washer and Dryer can be stacked to maximize usable space.

The dryer legs need to be removed to stack the Washer and Dryer. You can purchase an

optional stacking kit from you Samsung retailer.

10. 4-way Vent (electric model only : DV433E*)

You can install the exhaust vent in the following four (4) positions: back, either side, bottom.

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec9:3DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec9:3 2012-07-13  1:07:432012-07-13  1:07:43

4_ safety instructions

SAVE THESE INSTRUCTIONS

safety instructions

Congratulations on your new Samsung Dryer. This manual contains valuable

information on the installation, use, and care of your appliance. Please take the

time to read this manual to take full advantage of your dryer’s many benefits and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury

or death.

Follow the information in this manual to minimize the risk of fire or

explosion or to prevent property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids near

this or any other appliance.

CAUTION

Hazards or unsafe practices that may result in minor personal injury or

property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning signs are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec11:4DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec11:4 2012-07-13  1:07:432012-07-13  1:07:43

safety instructions _5

SAVE THESE INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your

appliance, follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in,

or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive

substances, as they give off vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any flammable substance, such

as vegetable oil, cooking oil, machine oil, flammable chemicals, thinner, etc., or anything

containing wax or chemicals, such as mops and cleaning cloths. Flammable substances

may cause the fabric to catch fire by itself.

4. Do not store or use gasoline or other flammable vapors and liquids near this or any other

appliance.

5. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

6. Before the appliance is removed from service or discarded, remove the door to the

drying compartment.

7. Do not reach into the appliance if the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with controls.

10.Do not repair or replace any part of the appliance or attempt any servicing unless

specifically recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

11.Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

12.Clean the lint screen before or after each load.

13.Do not use heat to dry articles containing foam rubber or similarly textured rubber-like

materials.

14.Keep area around the exhaust opening and adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

15.The interior of the appliance and exhaust duct should be cleaned periodically by

qualified service personnel.

16.Do not place items exposed to cooking oils in your dryer. Items contaminated with

cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

State of California Proposition 65 Warnings:

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of

California to publish a list of substances known to the State of California to cause cancer,

birth defects, or other reproductive harm, and requires businesses to warn of potential

exposure to such substances.

This product contains a chemical known to the State of California to cause cancer, birth

defects, or other reproductive harm. This appliance can cause low-level exposure to some

of the substances listed, including benzene, formaldehyde, and carbon monoxide.

Gas appliances may cause low-level exposure to some of the substances listed including

benzene, formaldehyde, carbon monoxide, and soot; as a result of possible incomplete

combustion of natural gas or LP fuels. Exposure to these substances can be minimized

further by properly venting the dryer to the outdoors.

WARNING

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec11:5DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec11:5 2012-07-13  1:07:432012-07-13  1:07:43

6_ safety instructions

SAVE THESE INSTRUCTIONS

safety instructions

• Clothes dryer installation must be performed by a qualified installer.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal

(foil type) duct is installed, it must be of a specific type identified by the appliance

manufacturer as suitable for use with clothes dryers. Flexible venting materials are

known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

• To reduce the risk of severe injury or death, follow all installation instructions.

WARNING - Risk of Fire

To reduce the risk of fire or explosion:

• Do not dry items that have been previously cleaned, washed, soaked, or spotted with

gasoline, dry cleaning solvents, or other flammable or explosive substances. They

emit vapors that could ignite or explode. Any material that has been in contact with a

cleaning solvent or flammable liquids or solids should not be placed in the dryer until all

traces of these flammable liquids or solids and their fumes have been removed.

There are many highly flammable items used in homes, such as acetone, denatured

alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,

turpentine, waxes, and wax removers

• Items containing foam rubber (may be labeled latex foam) or similarly textured rubber-

like materials must not be dried on a heat setting. Heated foam rubber materials can,

under certain circumstances, produce fire by spontaneous combustion.

What to do if you smell gas:

• Do not try to light any appliance.

• Do not turn on the appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Clear the room, building or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer, service agency, or the

gas supplier.

WARNING

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec11:6DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec11:6 2012-07-13  1:07:432012-07-13  1:07:43

contents _7

SAVE THESE INSTRUCTIONS

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is

necessary when the appliance is used near children and pets.

Before discarding or removing your dryer from service, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

Do not reach into the appliance when the drum is moving.

Do not install or store this appliance where it will be exposed to the weather.

Do not tamper with controls.

Do not repair, replace, or attempt to service any part of the appliance unless specifically

recommended in the user-repair instructions and you understand and have the skills to

carry those out.

Do not use fabric softeners or products to eliminate static unless recommended for dryer

use by the manufacturer of the fabric softener or product.

Clean the lint screen before or after each load.

Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt.

The interior of the dryer and exhaust duct should be cleaned periodically by qualified service

personnel.

This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately and in accordance with local and national codes. See

installation instructions for grounding this appliance.

Do not sit on top of the dryer.

Ensure pockets are free from small irregularly shaped hard objects, foreign material, etc. ie.

coins, knives, pins, etc. These objects could damage your dryer.

Do not wash clothing with large buckles, buttons, or other heavy metal or solid things.

Gas leaks may occur in your system, resulting in a dangerous situation.

Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with the manufacturer’s instructions.

Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking

oil. Even after being washed, these items may contain significant amounts of these oils.

Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous

combustion increases when items containing vegetable oil or cooking oil are exposed to

heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction

in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become

hot enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat

from escaping and can create a fire hazard.

All washed and unwashed fabrics that contain vegetable oil or cooking oil can be

dangerous. Washing these items in hot water with extra detergent will reduce, but not

eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their

temperature. Never remove these items from the dryer hot or interrupt the drying cycle until

the items have run through the Cool Down cycle. Never pile or stack these items when they

are hot.

WARNING

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec1:7DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec1:7 2012-07-13  1:07:432012-07-13  1:07:43

8_ installing your dryer

contents

INSTALLING YOUR DRYER

9 Unpacking your dryer

10 Basic requirments

11 Ducting requirements

12 Important to installer

12 Location considerations

13 Alcove or closet installation

15 Mobile home installation

15 Exhausting

16 Gas requirements

16 Commonwealth of Massachusetts

installation instructions

17 Electrical requirements

17 Grounding

18 Electrical connections

19 Connecting the inlet hose

20 Replacement parts and accessories

20 Installation

23 Final installation checklist

24 Dryer Exhaust Tips

25 Door Reversal

OPERATING INSTRUCTIONS, TIPS

26 Overview of the control panel

28 Child lock

29 Drum Light

29 Changing Language

29 My cycle

30 Rack Dry

31 Clean the lint filter

31 Load the dryer properly

31 Getting started

CARE AND CLEANING

32 Control Panel

32 Tumbler

32 Stainless Steel Tumbler

32 Dryer Exterior

32 Dryer Exhaust System

SPECIAL LAUNDRY TIPS

33 Special laundry tips

TROUBLESHOOTING

34 Check these points if your dryer…

36 Information codes

APPENDIX

37 Fabric care chart

38 Protecting the environment

38 Declaration of conformity

38 Specifications

39 Cycle chart

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:8DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:8 2012-07-13  1:07:432012-07-13  1:07:43

installing your dryer _9

installing your dryer

UNPACKING YOUR DRYER

Unpack your Dryer and inspect it for shipping damage. Make sure you have received all of the items

shown below. If your Dryer was damaged during shipping, or you do not have all of the items, contact

1-800-SAMSUNG(726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.

Packing materials can be dangerous to children; keep all packing material (plastic bags, polystyrene,

etc.) well out of the reach of children.

SEE EXHAUST REQUIREMENTS

Parts supplied

“Y”-connector Short inlet hose Rubber Washer Long inlet hose

01 installing your dryer

WARNING

Control panel

Top Cover

Door

Frame Front

Filter

Duct Exhaust

Water Inlet

[ BACK ]

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:9DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:9 2012-07-13  1:07:432012-07-13  1:07:43

10_ installing your dryer

installing your dryer

Tools needed

Pliers Cutting knife

Pipe wrench

(gas only)

Nut drivers

Level Phillips Screwdriver Duct tape Wrench

BASIC REQUIRMENTS

Make sure you have everything necessary for proper installation

• A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements.

• A POWER CORD electric dryers ( except for Canada).

• GAS LINES (if a gas dryer) must meet national and local codes.

• EHAUST SYSTEM - must be rigid metal or flexible stiff-walled metal exhaust ducting.

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:10DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:10 2012-07-13  1:07:442012-07-13  1:07:44

installing your dryer _11

DUCTING REQUIREMENTS

• Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

• Do not use a smaller duct.

• Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation.

Lint accumulation should be cleaned regularly.

• If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct

with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sharply.

• Never install any type of flexible duct in walls, ceilings, or other concealed spaces.

• Keep the exhaust duct as straight and short as possible.

• Secure joints with duct tape. Do not use screws.

• Plastic flexible duct can kink, sag, be punctured, reduce airflow, extend drying times, and affect dryer

operation.

• Exhaust systems longer than recommended can extend drying times, affect machine operation, and

may collect lint.

• The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and

entry of wildlife. Never use an exhaust hood with a magnetic damper.

• The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and

the ground or other obstruction. The hood opening should point down.

• Never install a screen over the exhaust outlet.

• To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house

or porch.

• If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly

down towards the exhaust hood to reduce condensation and lint buildup.

• Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before

cleaning.

• Check frequently to be sure the exhaust hood damper opens and closes freely.

• Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then

check ducting for obstructions.

• Do not exhaust dryer into any wall, ceiling, crawl space, or concealed space of a building, gas vent, or

any other common duct or chimney. This could create a fire hazard from lint expelled by the dryer.

ELECTRIC AND GAS DRYER

Weather Hood Type

Recommended Use only for short-run installation

4” (10 .16 cm) 2.5” (6.35 cm)

No. of 90° elbows Rigid Metallic Flexible* Rigid Metallic Flexible*

0 24.4 m (80 ft.) 12.4 m (41 ft.) 22.6 m (74 ft.) 10.1 m (33 ft.)

1 20.7 m (68 ft.) 11.2 m (37 ft.) 18.9 m (62 ft.) 8.8 m (29 ft.)

2 17.4 m (57 ft.) 10.1 m (33 ft.) 15.5 m (51 ft.) 7.6 m (25 ft.)

3 14.3 m (47 ft.) 9.0 m (29 ft.) 12.5 m (41 ft.) 6.5 m (21 ft.)

* Do not use non-metallic flexible duct.

01 installing your dryer

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:11DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:11 2012-07-13  1:07:452012-07-13  1:07:45

12_ installing your dryer

If the new dryer is installed into an existing exhaust system you must make

sure:

• The exhaust system meets all local, state, and national codes.

• That a flexible plastic duct is not used.

• To Inspect and clean all lint buildup from inside the existing duct.

• The duct is not kinked or crushed.

• The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be

less than 0.

This can be measured with the dryer running with a manometer at the point where the exhaust

duct connects to the dryer. A no-heat setting should be used. The dryer tumbler should be

empty and the lint filter clean.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept

for future reference.

Remove the door from all discarded appliances to avoid the danger of a child suffocating.

LOCATION CONSIDERATIONS

The dryer should be located where there is enough space at the front for loading the dryer, and enough

space behind for the exhaust system. This dryer is factory-ready for rear exhaust. To exhaust out the

bottom or the right or the left, use the accessory exhaust kit. Instructions are included with the kit. It’s

important to make sure the room has enough fresh air. The dryer must be located where there is no air-flow

obstruction.

On gas dryers, adequate clearance as noted on the data plate must be maintained to ensure adequate air

for combustion and proper dryer operation.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. The

dryer area is to be kept clear of combustible materials, casoline, and other flammable vapors and liquids. A

dryer produces combustible lint. The area around the dryer should be kept Lint-Free.

installing your dryer

WARNING

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:12DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:12 2012-07-13  1:07:462012-07-13  1:07:46

installing your dryer _13

ALCOVE OR CLOSET INSTALLATION

The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or

closet.

• No other fuel-burning appliance should be installed in the same closet as the dryer.

• WARNING: To reduce the risk of fire, this dryer must be exhausted to the outdoors.

See Exhaust information section.

MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:

Sides – 1 in / 25 mm

Rear – 5 in / 127mm

Top – 17 in / 432 mm

Closet Front – 2 in / 51 mm

If the washer and dryer are installed together, the closet front must have at least a 72 in² (465 cm²)

unobstructed air opening.

A. Recessed area

B. Side view - closet or confined area

01 installing your dryer

1 in.

(2.5 cm)

1 in.

(2.5 cm)

1 in.

(2.5 cm)

27 in.

(68.6 cm)

27 in.

(68.6 cm)

2 in.

(5 cm)

5 in.

(12.7 cm)

34.1 in.

(86.5 cm)

17 in.

(43.2 cm)

WARNING

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:13DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:13 2012-07-13  1:07:462012-07-13  1:07:46

14_ installing your dryer

With optional pedestal base or stacking kit

Required Dimensions for Installation With Pedestal

Required Dimensions for Installation With Stacking Kit

* Required spacing

** External exhaust elbow requires additional

space.

installing your dryer

1 in.

(2.5 cm)

27 in.

(68.6 cm)

77.2 in.

(196.2 cm)

6 in. *

(15.2 cm)

Closet or Door

48 in.² *

(310 cm²)

24 in.² *

(155 cm²)

3 in.

(7.6 cm)

3 in.

(7.6 cm)

1 in.

(2.5 cm)

34.1 in.

(86.5 cm)

5.5 in.**

(14 cm)

2.5 in.

(6.3 cm)

27 in.

(68.6 cm)

38.6 in.

(98.1 cm)

53.6 in.

(136.2 cm)

5 in.

(12.7 cm)

341.1 in.

(86.5 cm)

51.2 in. (130 cm) to clear open door

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:14DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:14 2012-07-13  1:07:462012-07-13  1:07:46

installing your dryer _15

MOBILE HOME INSTALLATION

The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and

Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada).

When installing a dryer in a mobile home, provisions for anchoring the dryer to the floor must be made.

Locate an area that has adequate fresh air.

A minimum of 72 in² (465 cm²) of unobstructed space is required.

Call 1-800-SAMSUNG for information on purchasing the Floor Anchoring Kit as an accessory.

All mobile home installations must be exhausted to the outside with the exhaust duct termination securely

fastened to the mobile home structure, using materials that will not support combustion.

The exhaust duct may not terminate underneath the mobile home.

See Exhausting section for more information.

EXHAUSTING

Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the

room.

In the United States:

• All dryers must be exhausted to the outside.

• The required exhaust duct is 4inch(102mm) in diameter.

• Only those foil-type flexible ducts, if any, specifically identified for use with the appliance by

the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct, Subject

2158A, shall be used.

• The duct shall not be assembled with screws or other fastening means that extend into the

duct and catch lint.

In Canada:

• Only those foil-type flexible ducts, if any, specifically identified for use with the appliance by

the manufacturer shall be used.

• All dryers must be exhausted to the outside.

• The exhaust duct should be 4inch (102mm) in diameter.

Outside the U.S. and Canada:

• Refer to the local codes.

The dryer must be exhausted to the outside to reduce the risk of fire when installed in an

alcove or closet.

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.

If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air,

heat, and lint.

01 installing your dryer

WARNING

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:15DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:15 2012-07-13  1:07:472012-07-13  1:07:47

16_ installing your dryer

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL

CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED

STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP

(liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician.

A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas

line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off

valve be installed within 6” of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of your dryer’s gas supply connection.

Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the

system.

DO NOT reuse old flexible metal gas lines. Flexible gas lines must be design certified by the American Gas

Association (CGA in Canada).

• Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.

• As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION – Your dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

COMMONWEALTH OF MASSACHUSETTS INSTALLATION

INSTRUCTIONS

Your dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve must be

installed in the gas supply line to your dryer. If a flexible gas connector is used to install your dryer, the

connector must have a maximum length of 3’ (36”).

• Gas leaks may occur in your system, creating a dangerous situation.

• Gas leaks may not be detected by smell alone.

• Gas suppliers recommend you purchase and install a UL-approved gas detector.

• Install and use in accordance with manufacturer’s instructions.

installing your dryer

WARNING

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:16DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:16 2012-07-13  1:07:472012-07-13  1:07:47

installing your dryer _17

ELECTRICAL REQUIREMENTS

• Improper connection of the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is

properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet,

have a proper outlet installed by a qualified electrician.

• To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding

must be done in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code

CSA C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide

adequate electrical services for your dryer.

• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Latest

Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and

local codes and ordinances.

GROUNDING

This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of

electrical shock by providing a path of least resistance for the electrical current.

Gas models

Your dryer has a cord with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet

installed by a qualified electrician.

Never connect ground wire to plastic plumbing lines, gas lines, or hot water pipes.

Electric models

Your dryer has a cord with an equipment-grounding conductor and a grounding plug, sold

separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet

installed by a qualified electrician.

If a power cord is not used and the electric dryer is to be permanently wired, the dryer must

be connected to a permanently grounded metal wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment grounding

terminal.

01 installing your dryer

WARNING

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:17DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:17 2012-07-13  1:07:472012-07-13  1:07:47

18_ installing your dryer

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the Grounding section.

An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN

EXTENSION CORD.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is

required.

Electric models – U.S. only

Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require

120/208 volt, 60 Hz approved electrical service. The electric service requirements can be found

on the data label located behind the door. A 30-ampere fuse or circuit breaker on both sides of

the line is required.

• If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

• The power cord is NOT provided with U.S. electric model dryers.

IMPORTANT:

When local codes allow, the dryer electrical supply may be connected by means of a new power

supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of120/240

volts, 30-ampere with three No. 10 copper wire conductors terminated with closed loop

terminals, open-end spade lugs with turned up ends, or with tinned leads.

• Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring

must be retained at the dryer cabinet with a suitable UL-listed strain relief.

• Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit

grounding through the neutral conductor. (Use 4-prong plug for 4 wire receptacle, NEMA

type 14-30R.)

Electric models – Canada Only

• A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or

circuit breaker on both sides of the line is required.

• All Canadian models are shipped with the power cord attached. The power cord should be

plugged into a 30-ampere receptacle.

It is not permissible to convert a dryer in Canada to 208 volts.

installing your dryer

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:18DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:18 2012-07-13  1:07:472012-07-13  1:07:47

installing your dryer _19

CONNECTING THE INLET HOSE

Method1

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old

hoses.

1. If space permits, attach the brass female end of the “Y”

connector to the cold water faucet.

2. Turn the cold water faucet off.

3. Attach the straight end of long hose to “Y’ connector.

4. Using pliers, tighten the coupling with an additional two-

thirds turn.

Do not overtighten, as it may damage the coupling.

5. Attach angled end of long hoses to fill the valve at the

bottom of the dryer’s rear frame. Screw on coupling by hand

until it is seated on fill valve connector.

6. Using pliers, tighten the coupling with an additional two-

thirds turn.

Do not overtighten, as it may damage the coupling.

7. Check that the water faucets are on.

Check for leaks around “Y” connector, faucets and hoses.

Method2

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old

hoses.

1. If “Y” connector cannot be attached directly to the cold

water faucet, the short hose must be used.

2. Turn the cold water faucet off.

3. Attach short inlet hose to cold water faucet.

Screw on coupling by hand until it is seated on the faucet.

4. Using pliers, tighten the coupling with an additional two-

thirds turn.

Do not overtighten, as it may damage the coupling.

5. Attach ‘Y” connector to brass male end of small hose.

Screw on coupling by hand until it is seated on connector.

6. Using pliers, tighten the coupling with an additional two-

thirds turn.

Do not overtighten, as it may damage the coupling.

7. Attach angled end of long hoses to the fill valve at the

bottom of the dryer rear frame. Screw on coupling by hand

until it is seated on fill valve connector.

8. Using pliers, tighten the coupling with an additional two-

thirds turn.

Do not overtighten, as it may damage the coupling.

9. Check that the water faucets are on.

10. Check for leaks around “Y” connector, faucets and hoses.

01 installing your dryer

Duct Exhaust

Frame

(back)

Water Hose

Y-Connector

Water Hose

Short hose

(Inlet to cold

water)

“Y’ connector

Long hose

Duct Exhaust

Frame

(back)

Water Hose

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:19DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:19 2012-07-13  1:07:472012-07-13  1:07:47

20_ installing your dryer

REPLACEMENT PARTS AND ACCESSORIES

If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your

dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864).

INSTALLATION

For proper installation, we recommend that you hire a qualified installer.

To install:

1. Move your dryer to an appropriate location for installation. Consider

installing the dryer and washer side-by-side, to allow access to gas,

electrical, and exhaust connections.

Lay two of the carton cushion-tops on the floor. Tip your dryer on its

side so it will lay across both cushion-tops.

2. Set your dryer back in an upright position.

3. To ensure that the dryer provides optimal drying performance, it must

be level. To minimize vibration, noise, and unwanted movement,the

floor must be a perfectly level, solid surface.

To set the dryer to the same height as the washer, fully retract the

leveling feet by turning them counterclockwise, then loosen the leg

by turning them clockwise

Adjust the leveling feet only as much as necessary to level the dryer.

Extending the leveling feet more than necessary can cause the dryer

to vibrate.

installing your dryer

Level

Leveling feet

Retract fully Then loosen

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:20DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:20 2012-07-13  1:07:482012-07-13  1:07:48

installing your dryer _21

4. Review the Exhausting section before installing the exhaust system. Install the ductwork from your dryer

to the exhaust hood. The crimped end of the duct sections must point away from your dryer.

DO NOT use sheet metal screws when assembling ducting. These joints should be taped.

Never use plastic flexible exhaust material.

Tip for tight installations: install a section of exhaust system to your dryer before putting it in place.

Use duct tape to secure this section to your dryer, but do not cover ventilation slots at the back of the

unit in dryer cabinet.

5. Review Electrical Requirements section.

BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section.

U.S. MODELS:

IMPORTANT – All U.S. models are produced for a 3-WIRE SYSTEM CONNECTION.

The dryer frame is grounded to the neutral conductor at the terminal block.

A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile

homes, or if local codes do not permit grounding through neutral. If the 4-wire system is used,

the dryer frame cannot be grounded to the neutral conductor at the terminal block. Refer to the

following instructions for 3- and 4-WIRE SYSTEM CONNECTIONS.

Remove the terminal block cover plate.

Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the

terminal block.

A strain relief must be used.

Do not loosen the nuts already installed on the terminal block. Be sure they are tight.

Use a 3/8” (1cm) deep well socket.

01 installing your dryer

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:21DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:21 2012-07-13  1:07:482012-07-13  1:07:48

22_ installing your dryer

6. Review Gas Requirements section.

Remove the pipe thread protective cap.

Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections.

Pipe joint compound must be resistant to the action of any liquefied petroleum gas.

Connect the gas supply to your dryer.

An additional fitting is required to connect the 3/4” (1.9 cm) female thread end of a flexible connector to

the 3/8” (1 cm) male threaded end on the dryer.

Securely tighten the gas line fitting over threads.

Turn on the gas supply. Check all gas connections for leaks using a soap solution.

If bubbles appear, tighten the connections and recheck.

DO NOT use an open flame to check for gas leaks.

3-WIRE system connections

1. Loosen or remove the center terminal block screw.

2. Connect the neutral wire (white or center wire) of the power

cord to the center, silver-colored terminal screw of the

terminal block. Tighten screw.

3. Connect the other wires to outer terminal block screws.

Tighten screws.

4. Tighten the strain relief screws.

5. Insert the tab of the terminal block cover into your dryer’s

rear panel slot.

Secure the cover with a hold-down screw.

1. External ground connector

2. Neutral grounding wire (green/yellow)

3. Center silver-colored terminal block screw

4. Neutral wire (white or center wire)

5. 3/4” (1.9 cm) UL-listed strain relief

If converting from a 4-wire electrical system to a 3-wire, the ground strap must be

reconnected to the terminal block support to ground the dryer frame to the neutral

conductor.

installing your dryer

WARNING

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:22DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:22 2012-07-13  1:07:482012-07-13  1:07:48

installing your dryer _23

4-WIRE system connections

1. Remove the center terminal block screw.

2. Connect the ground wire (green or unwrapped) of the power

cord to the external ground conductor screw.

3. Connect the neutral wire (white or center wire) of the power

cord and the appliance ground wire (green with yellow

stripes) under the central screw of the terminal block.

4. Connect the other wires to the outer terminal block screws.

Tighten screws.

5. Tighten the strain relief screws.

6. Insert the tab of the terminal block cover into your dryer’s rear panel slot.

Secure the cover with a hold-down screw.

1. External ground connector

2. Green or bare copper wire of power cord

3. 3/4 in. (1.9 cm) UL-listed strain relief

4. Center silver-colored terminal block screw

5. Grounding wire (green/yellow)

6. Neutral wire (white or center wire)

7. With a level, check your dryer and make necessary adjustments to the leveling legs.

8. At this time, make sure all gas connections (on gas models), exhaust and electrical connections are

complete. Plug in your dryer, and check operation by using the checklist below.

9. (GAS MODELS ONLY)

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat

setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5

minutes. Be sure the gas supply to your dryer has been turned on. In order to confirm gas ignition,

check the exhaust for heat.

FINAL INSTALLATION CHECKLIST

 Dryer is plugged into electrical outlet and is properly grounded.

 Exhaust ductwork is hooked up and joints are taped.

 Plastic flexible duct is NOT used.

 Used rigid or stiff-walled flexible metal vent material.

 Dryer is leveled and is sitting firmly on the floor.

 Gas models – gas is turned on with no gas leaks.

 Start your dryer to confirm that it runs, heats, and shuts off.

01 installing your dryer

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:23DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:23 2012-07-13  1:07:482012-07-13  1:07:48

24_ installing your dryer

DRYER EXHAUST TIPS

Plastic or non-metal flexible duct presents a potential fire hazard.

1. Make sure your dryer is installed properly so it exhausts air

easily.

2. Use 4” diameter rigid metal duct. Tape all joints, including at

the dryer.

Never use lint-trapping screws.

3. Keep ducts as straight as possible.

4. Clean all old ducts before installing your new dryer.

Be sure the vent flap opens and closes freely.

Inspect and clean the exhaust system annually.

Don’t let a poor exhaust system slow drying by:

1. Restricting your dryer with a poor exhaust system.

2. Using a plastic, thin foil, or non-metal flexible duct.

3. Unnecessarily using long ducts that have many

elbows.

4. Allowing crushed or clogged ducts and vent.

installing your dryer

WARNING

1 2

3 4

DUCT

TAPE

Wall

Duct

Exhaust

Dryer

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:24DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:24 2012-07-13  1:07:482012-07-13  1:07:48

installing your dryer _25

DOOR REVERSAL

1. Unplug the power cord.

2. Remove two door hinge

screws.

3. Lift the door and remove

it.

8. Remove a screw from the

door hinge.

The screw is for pre-

fixing the door to the

frame front.

4. Remove two screws from

the frame front.

9. Reassemble the screw in

the other hole.

5. Remove the two screws

from the opposite side of

the door hinge.

10. Place the door on the

other side and reattach it

to the dryer.

6. Remove two screws from

the holder lever.

11. Reattach the holder lever.

7. Reassemble two screws

on inside holes.

12. Reattach the screws in

the remaining holes.

01 installing your dryer

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:25DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec2:25 2012-07-13  1:07:492012-07-13  1:07:49

26_ operating Instructions, tips

operating Instructions, tips

OVERVIEW OF THE CONTROL PANEL

Cycle Selector

o select a cycle, rotate the Cycle Selector dial to the desired cycle.

The indicator light by the cycle name will illuminate. The Wool, Delicates,

Bedding Plus(Bedding), Perm Press, Heavy Duty, Normal, Eco Normal and

Sanitize cycles are Sensor Dry cycles.

Sensor Dry automatically senses the moisture in the load and shuts the dryer

off when the selected dryness level (very dry to damp dry) is reached.

Eco Normal – This cycle reduces energy usage by 10% to 15% compared

to Normal Dry depending on load. It adjusts cycle time and temperature for

better efficiency with Samsung smart control technology.

Normal – Use this cycle to dry loads such as cotton, underwear, and linen.

Heavy Duty – Use this cycle to get high heat for heavy fabrics such as jeans,

corduroys, or work clothes.

Perm Press – Dry wrinkle-free cottons, synthetic fabrics, knits, and

permanent press fabrics automatically.

Bedding (DV433*) – For bulky items such as blankets, sheets and comforters.

Delicates – The Delicates cycle is designed to dry heat-sensitive items at a

low drying temperature.

Wool – For machine washable and tumble dryable wool only.

Sanitize – This course allows you to sanitize garments by permeating high

temperature heat deep into the fabric during the drying cycle. Use this course to

keep your Bedding Plus and curtains clean through sanitization.

Time Dry – Time Dry allows you to select the desired cycle time in minutes.

Turn the Cycle Selector dial to Time Dry, then press the Adjust Time up arrow to

set the drying time. Press the arrow repeatedly to scroll through the time settings.

Quick Dry - Provides a 30 minutes drying cycle.

Air Fluff – The Air Fluff cycle tumbles the load in room temperature air.

Refresh – This cycle is best for smoothing out wrinkles and reducing odors from

loads consisting of one to four dry items. In this cycle a small amount of water is

sprayed into the dryer drum after several minutes of tumbling with heat.

Wrinkle Away – Use this cycle to reduce wrinkles from dry clothes that have

been left in closet for a while. It provides advanced wrinkle release performance

by optimized steam care. Up to 3 items can be used.

Overloading the dryer may not yield the same results.

36 4 5 7

108

8 2

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:26DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:26 2012-07-13  1:07:512012-07-13  1:07:51

operating Instructions, tips _27

LED Display

The display window shows the estimated time remaining in the cycle after the

Start/Pause button is pressed. The estimated time remaining may fluctuate as

the cycle progresses.

The Drying light will illuminate and remain lit until the cycle is complete.

When your dryer is in the cool-down phase, the Cooling light will illuminate.

When your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will

illuminate.

When the cycle is complete, “END” will appear in the display panel until the

dryer door is opened or the Power button is pushed.

If your dryer is paused during a cycle, the indicator lights will blink until the

Start/ Pause button is pressed.

Dry Level

Selection Button

To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles,

press the Dry Level button. An indicator light will illuminate next to the desired

dryness level.

Press the button repeatedly to scroll through the settings. Larger or bulkier

loads may require the Very Dry or More Dry setting for complete dryness.

The Less Dry setting is best suited for lightweight fabrics or for leaving some

moisture in the clothing at the end of the cycle. Damp Dry is designed to

partially dry items. Use for items that lay flat or hang to dry.

Temp Selection

Button

To select the correct temperature for the load, press the Temp button. An

indicator light will illuminate next to the desired temperature. Press the button

repeatedly to scroll through the settings.

High – For sturdy cottons or those labeled Tumble Dry.

Medium – For permanent press, synthetics, lightweight cottons, or items

labeled Tumble Dry Medium.

Med Low – For lower heat than Medium to dry synthetic or washable knit

fabrics.

Low – For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.

Extra Low – Provides the lowest heated dry temperature possible.

Time Selection

Button

When using Manual Dry cycles, time can be adjusted by pressing the time

selection button.

During the Sensory Dry cycle, the time light indicator is off because exact

drying times are determined by fluctuating humidity levels.

Signal Selection

Button

When the cycle is complete, a chime will sound.

When the Wrinkle Prevent option is selected, the chime will sound

intermittently.

Adjust the volume of the chime or turn it off by pressing the Signal button.

Press the button repeatedly to scroll through the choices.

Delay Start

Button

Any cycle can be delayed for up to 24 hours in one-hour increments.

Displayed hour indicates the time at which the wash will be started

02 operating Instructions, tips

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:27DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:27 2012-07-13  1:07:512012-07-13  1:07:51

28_ operating Instructions, tips

Select Cycle

Option

Adjust Time – Time can be added or subtracted from the automatically set

times in the Manual Dry cycles (Time Dry, Quick Dry, or Air Fluff cycles).

To add or subtract time from the cycle, press the Adjust Time arrow pad up

or down until the desired time is displayed.

Wrinkle Prevent -Wrinkle Prevent provides approximately 180 minutes

of intermittent tumbling in unheated air at the end of the cycle to reduce

wrinkling. Press the Wrinkle Prevent button to activate this feature.

The indicator light above the pad will illuminate when Wrinkle Prevent is

selected.

The load is dry, and can be removed at any time during the Wrinkle Prevent

cycle.

My Cycle – Choose your favorite cycle including cycle, temp, dry level option,

etc. (See page 29 for detail.)

Rack Dry – Rack Dry is available at Time Dry cycle. Temperature will be set

only to Extra Low. (See page 30 for detail.)

Mixed Load Bell - The mixed load bell that notifies you when the average

dry level in a load is damp dry (80 % dried). This lets you take garments that

you don’t want fully dried or that dry quickly out of the dryer early while letting

others continue to dry.

You can select this function in all Sensor Dry cycles except Wool, Sanitize.

The dry level selections are limited to Normal Dry, More Dry, and Very Dry.

Start/Pause

selection button

Press to pause and restart programs.

Power button

Press once to turn your dryer on, press again to turn it off. If your dryer is left

on for more than 10 minutes without any buttons being touched, the power

automatically turns off.

CHILD LOCK

A function to prevent children from playing with your dryer.

Setting/Releasing

If you want to set or release the Child Lock, press both the Temp. and Time buttons

simultaneously for 3 seconds.

How to Set:

1. It can be set while your dryer is running.

2. Once you set the Child Lock function, no button, except for the Power button, will respond

until you release the Child Lock function.

3. The Child Lock indicator will be lit.

1. If the dryer is powered on again, the Child Lock function stays on.

2. To release that function, follow the instructions above.

When other buttons, except for the Power button, do not respond, check the Child Lock

indicator.

operating Instructions, tips

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:28DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:28 2012-07-13  1:07:512012-07-13  1:07:51

operating Instructions, tips _29

DRUM LIGHT

Lights the dryer drum while the dryer is running.

Setting & releasing

If you want to set or release the Drum Light, press both the Dry Level and Temp. buttons

simultaneously.

It can be set while your dryer is not only running but also when it is stopped.

If you do not turn the Drum Light off 5 minutes after turning it on, the Drum Light is

automatically turned off.

CHANGING LANGUAGE

You may change the language shown in the display from English to French or Spanish.

Press and hold the Rack Dry and Wrinkle Prevent buttons for 3 seconds until the display changes. Then

select the desired language by pressing the Signal button.

Once set, the selected language will remain in memory, even if the dryer is turned off or unplugged.

MY CYCLE

Lets you activate your customized cycle that includes Dry Level, Temp, Time option, etc.

By pushing the My Cycle button, you activate the settings used during the previous My Cycle mode.

(Default : Normal Cycle)

If My Cycle mode is activated, the My Cycle indicator will be lit.

You can select all options in My Cycle mode as follows.

1. Select cycle using the Cycle Selector dial.

2. After cycle selection, set each option.

Each cycle has certain default options that are automatically set.

3. Then, you can start My Cycle by pushing the Start/Pause button in My Cycle mode. The cycle and

options you select will be displayed the next time you choose My Cycle.

You can change the My Cycle settings by repeating the same process above.

The last used setting will be displayed the next time you choose My Cycle.

02 operating Instructions, tips

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:29DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:29 2012-07-13  1:07:512012-07-13  1:07:51

30_ operating Instructions, tips

RACK DRY

Installing the drying rack

1. Open the dryer door.

2. Position drying rack in tumbler, placing the front lip of the drying rack on the top of the lint

filter.

3. Place the rear legs in the two recessed areas of the dryer’s back wall then push down the

middle of the drying rack to fix.

4. Place the items to be dried on the rack, leaving space between them so air can circulate.

5. Close the dryer door.

6. Press the RACK DRY button at Time Dry cycle and then select the time according to the

moisture and weight of item. The drying rack can be also used at Air Fluff cycle.

SUGGESTED ITEMS SUGGESTED TEMP. SETTINGS

Washable sweaters

(block to shape and lay flat on rack)

Extra Low ( Time Dry cycle)

Stuffed toys

(cotton or polyester fiberfilled)

Extra Low ( Time Dry cycle)

Stuffed toys

(foam or rubber-filled)

Air Fluff

Foam rubber pillows Air Fluff

Sneakers Air Fluff

Drying foam rubber, plastic, or rubber on a heat setting may cause damage to the items

and lead to a fire hazard.

operating Instructions, tips

WARNING

Door

Drying Rack

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:30DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:30 2012-07-13  1:07:522012-07-13  1:07:52

operating Instructions, tips _31

CLEAN THE LINT FILTER

• After each load.

• To shorten drying time.

• To operate more energy efficiently.

Do not operate your dryer without the lint filter in place.

LOAD THE DRYER PROPERLY

• Place only one washload in your dryer at a time.

• Mixed loads of heavy and lightweight fabrics will dry differently, which may result in lightweight fabrics

being dry while heavy fabrics remain damp at the end of a drying cycle.

• Add one or more similar items to your dryer when only one or two articles of clothing need drying.

This improves the tumbling action and drying efficiency.

• Overloading restricts tumbling action, resulting in uneven drying as well as excessive wrinkling of some

fabrics.

GETTING STARTED

1. Load your dryer loosely – DO NOT overload.

2. Close the door.

3. Select the appropriate cycle and options for the load.

4. Press the Start/Pause button.

5. The dryer indicator light will illuminate.

6. The estimated cycle time will appear in the display.

The time may fluctuate as humidity levels fluctuate in the dryer.

• When the cycle is complete, the Door Lock light will go out and “End” will appear in the display.

• Pressing Power cancels the cycle and stops your dryer.

• The Drying, Cooling, and Wrinkle Prevent indicator lights will illuminate during those portions of the

cycle.

Do not place anything on top of your dryer while it is running.

02 operating Instructions, tips

WARNING

Filter

Door

Frame Front

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:31DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec3:31 2012-07-13  1:07:522012-07-13  1:07:52

32_ care and cleaning

care and cleaning

CONTROL PANEL

Clean with a soft, damp cloth. Do not use abrasive substances.

Do not spray cleaners directly on the panel.

The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products.

Apply such products away from your dryer and wipe up any spills or overspray immediately.

TUMBLER

Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an all-

purpose cleaner.

Tumble old towels or rags to remove any excess stain or cleaning substance.

Once these steps are followed, stains may still be visible, but should not transfer to subsequent loads.

STAINLESS STEEL TUMBLER

To clean the stainless steel tumbler, use a damp cloth with a mild, non-abrasive cleaner suitable for stainless

steel surfaces.

Remove the cleaner residue and dry with a clean cloth.

DRYER EXTERIOR

Clean with a soft, damp cloth. Do not use abrasive substances.

Protect the surface from sharp objects.

Do not place any heavy or sharp objects or a detergent box on the dryer. Keep them on the purchased

pedestal or in a separate storage box. This may scratch or damage the top cover of the dryer.

Since the entire dryer has a high-gloss finish, the surface can be scratched or damaged.

Therefore, avoid scratching or damaging the surface when using the dryer.

DRYER EXHAUST SYSTEM

Should be inspected and cleaned yearly to maintain optimum performance.

The outside exhaust hood should be cleaned more frequently to ensure proper operation.

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec5:32DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec5:32 2012-07-13  1:07:522012-07-13  1:07:52

special laundry tips _33

special laundry tips

Special laundry tips

Please follow the care label or manufacturer’s instructions for drying special

items. If care label instructions are not available, use the following information as

a guide.

Bedspreads & Comforters

• Follow the care label instructions or dry on the Bedding Plus.

• Make sure the item is thoroughly dry before using or storing.

• May require repositioning to ensure even drying.

Blankets

• Use Normal cycle and dry only one blanket at a time for best

tumbling action.

• Make sure the item is thoroughly dry before using or storing.

Curtains & Draperies

• Use the Perm Press cycle and Low or Extra Low temperature to help

minimize wrinkling.

• Dry these in small loads for best results and remove as soon as

possible.

Cloth Diapers

• Use the Normal cycle and the High temperature settings for soft,fluffy

diapers.

Down–filled Items (jackets,

sleeping bags, comforters,

etc.)

• Use the Normal cycle and the Low or Extra Low temperature setting.

• Adding a couple of dry towels shortens drying time and absorbs

moisture.

Foam Rubber (rug backs,

stuffed toys, shoulder pads,

etc.)

• DO NOT dry on a heat setting. Use the Air Fluff cycle (no heat).

• WARNING – Drying a rubber item with heat may damage it or be a

fire hazard.

Pillows

• Use the Normal cycle.

• Add a couple of dry towels and a pair of clean sneakers to help the

tumbling action and to fluff the item.

• DO NOT dry kapok or foam pillows in dryer. Use the Air Fluff cycle.

Plastics (shower curtains,

outdoor furniture covers,

etc.)

• Use the Air Fluff cycle or the Time Dry cycle and the Low or Extra

Low temperature settings depending on the care label instructions.

THINGS TO AVOID :

• Fiberglass items (curtains, draperies, etc.).

• Woolens, unless recommended on the label.

• Vegetable or cooking oil-soaked items.

04 special laundry tips

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec4:33DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec4:33 2012-07-13  1:07:522012-07-13  1:07:52

34_ troubleshooting

troubleshooting

CHECK THESE POINTS IF YOUR DRYER…

PROBLEM SOLUTION

Doesn’t run.

• Make sure the door is latched shut.

• Be sure the power cord is plugged into a live electrical outlet.

• Check the home’s circuit breaker and fuses.

• Press the Start/Pause button again if the door is opened during the

cycle.

Doesn’t heat.

• Check the home’s circuit breaker and fuses.

• Select a heat setting other than Air Fluff.

• On a gas dryer, check that the gas supply is on.

• Clean the lint filter and exhaust duct.

• Dryer may have moved into the cool-down phase of the cycle.

Doesn’t dry.

• Check all of the above, plus...

• Be sure the exhaust hood outside the home can open and close

freely.

• Check exhaust system for lint buildup. Ducting should be inspected

and cleaned annually.

• Use a 4” rigid metal exhaust duct.

• Do not overload. 1 wash load = 1 dryer load.

• Sort heavy items from lightweight items.

• Large, bulky items like blankets or comforters may require

repositioning to ensure even drying.

• Check that the washer is draining properly to extract adequate water

from the load.

• Load may be too small to tumble properly. Add a few towels.

Is noisy.

• Check the load for objects such as coins, loose buttons, nails, etc.

Remove promptly.

• It is normal to hear the dryer gas valve or heating element cycle on

and off during the drying cycle.

• Be sure the dryer is leveled properly as outlined in the installation

instruction.

• It is normal for the dryer to hum due to the high velocity of air moving

through the dryer drum and exhaust system.

Dries unevenly.

• Seams, pockets, and other similarly heavy areas may not be

completely dry when the rest of the load has reached the selected

dryness level. This is normal. Select the Very Dry setting if desired.

• If one heavy item is dried with a lightweight load, such as one towel

with sheets, it is possible that the heavy item will not be completely

dry when the rest of the load has reached the selected dryness level.

Sort heavy items from lightweight items for best drying results.

Has an odor.

• Household odors from painting, varnishing, strong cleaners, etc.

may enter the dryer with the surrounding room air. This is normal as

the dryer draws the air from the room, heats it, pulls it through the

tumbler, and exhausts it outside.

• When these odors linger in the air, ventilate the room completely

before using the dryer.

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec6:34DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec6:34 2012-07-13  1:07:522012-07-13  1:07:52

troubleshooting _35

PROBLEM SOLUTION

Shuts off before load is dry

• Dryer load is too small. Add more items or a few towels and restart

the cycle.

• Dryer load is too large. Remove some items and restart the dryer.

Lint on clothes

• Make sure the lint filter is cleaned before every load. With some loads

that produce high amounts of lint, it may be necessary to clean the

filter during the cycle.

• Some fabrics are lint producers (for example, a fuzzy white cotton

towel)and they should be dried separately from clothes that are lint

trappers(for example, a pair of lack linen pants)

• Divide larger loads into smaller loads for drying

• Check pockets thoroughly before washing and drying clothes.

Garments still wrinkled after

Wrinkle-Care

• Small loads of 1 to 4 items work best.

• Load fewer garments.Load similar-type garments.

Odors remain in clothing

after Refresh.

• Fabrics containing strong odors should be washed in a normal cycle.

Water drips from nozzle

when Steam-Care starts

• This is steam condensation. The dripping water will stop after a short

time.

Sprayed water is not visible

during Steam-Care

• Sprayed water is difficult to see when the door is closed

05 troubleshooting

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec6:35DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec6:35 2012-07-13  1:07:522012-07-13  1:07:52

36_ troubleshooting

INFORMATION CODES

Information codes may be displayed to help you better understand what is occurring with your Dryer.

ERROR DISPLAY MEANING SOLUTION

Clogged Lint Screen

Vent is restricted

Clean the screen or vent.

If the problem continues call for service.

Running the dryer with door open

Close the door and then restart.

If the problem continues call for service.

Door is not closing properly Call for service.

bE2

Invalid state of key circuit short for

30secs

Make sure a button is NOT being pressed

continuously. Try restarting the cycle.

If the problem continues call for service.

Invalid heating Temp in running the

dryer

Call for service.

Invalid power source Frequency

Try restarting the cycle.

If the problem continues call for service.

Electronic Control Problem

(Communication Error)

Call for service.

Electronic Control Problem (Over

Voltage Error)

Call for service.

For any codes not listed above, call 1–800–726–7864 (1–800–SAMSUNG)

troubleshooting

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec6:36DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec6:36 2012-07-13  1:07:522012-07-13  1:07:52

appendix _37

appendix

FABRIC CARE CHART

The following symbols provide garment care direction. The Clothing care labels include symbols for

washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures

consistency among garment manufacturers of domestic and imported items. Follow care label directions to

maximize garment life and reduce laundering problems.

Wash Cycle Special Instructions

Warning Symbols for

Laundering

Normal Line Dry/ Hang to Dry Do Not Wash

Permanent Press /

Wrinkle Resistant /

Wrinkle Control

Drip Dry Do Not Wring

Gentle/Delicates Dry Flat Do Not Bleach

Hand Wash

Heat Setting

Do Not Tumble Dry

Water Temperature**

High

No Steam (added to

iron)

Hot Medium Do Not Iron

Warm Low

Dryclean

Cold Any Heat Dry Clean

Bleach

No Heat/Air Do Not Dry Clean

Any Bleach (when

needed)

Iron-Dry or Steam

Temperatures

Line Dry/ Hang to Dry

Only Non-Chlorine

(color-safe)

Bleach (when needed)

High Drip Dry

Tumble Dry Cycle Medium Dry Flat

Normal

Low

Permanent Press/

Wrinkle Resistant/

Wrinkle Control

Gentle/ Delicates

** The dot symbols represent appropriate wash water temperatures for various items. The temperature

range for Hot is 105° –125° F/ 41° – 52° C, for Warm 85° – 105° F/29° – 41° C and for Cold 60° – 85°

F/16° – 29° C. (Wash water temperature must be a minimum of 60° F/16° C for detergent activation and

effective cleaning.)

06 appendix

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec7:37DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec7:37 2012-07-13  1:07:522012-07-13  1:07:52

38_ appendix

PROTECTING THE ENVIRONMENT

This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please

observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected

to a power source. Remove the door so that animals and small children cannot get trapped inside the

appliance.

DECLARATION OF CONFORMITY

This appliance complies with UL2158.

SPECIFICATIONS

TYPE FRONT LOADING DRYER

DIMENSIONS

Div Inches (cm) Div Inches (cm)

A. Height

39” (99.1)

C. Depth with

door open 90°

51.65”(131.2)

B. Width

27” (68.6)

D. Depth

32.28”(82.0)

WEIGHT

127.8 lb (58Kg)

HEATER RATING

5300 W (Elec.)

22000 BTU/hr (Gas)

POWER

CONSUMPTION

NO HEAT

268 W

HEATING

5445 W (Elec.)

268 W (Gas)

appendix

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec7:38DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec7:38 2012-07-13  1:07:532012-07-13  1:07:53

appendix _39

CYCLE CHART

Elec. Dryer Type

Model : DV433E*

Cycle

Default Drying Cooling

Wrinkle

prevent

Temp

control

Sensor dry

level

Time Time Time Time

Sensor Dry

Normal High(Medium) Normal dry 42 min 39 min 3 min

180 min

Heavy Duty

High

(No change)

Normal dry 58 min 55 min 3 min

Perm Press

Medium

(No change)

Normal dry 32 min 29 min 3 min

Bedding

High

(No change)

Normal dry 50 min 47 min 3 min

Delicates

Extra Low

(No change)

Normal dry 34 min 33 min 1 min

Sanitize

High

(No change)

Very dry

(No change)

60 min 55 min 5 min

Eco Normal

Medium Low

(No change)

Normal dry

(No change)

78 min 75 min 3 min

Wool

Low

(No change)

Normal dry

(No change)

20 min 19 min 1 min

Manual Dry

Air Fluff

(No change)

20 min - 20 min

Quick Dry

High

(No change)

30 min 27 min 3 min

Time Dry High

(No change)

40 min 37 min 3 min

Steam

Cycles

Wrinkle Away

High

(No change)

20 min 19 min 1 min

Refresh

High

(No change)

15 min 14 min 1 min

06 appendix

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec7:39DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec7:39 2012-07-13  1:07:532012-07-13  1:07:53

40_ appendix

appendix

CYCLE CHART

Gas Dryer Type

Models : DV433G*

Cycle

Default Drying Cooling

Wrinkle

prevent

Temp

control

Sensor dry

level

Time Time Time Time

Sensor Dry

Normal

High

(Medium)

Normal dry 42 min 39 min 3 min

180 min

Heavy Duty

High

(No change)

Normal dry 58 min 55 min 3 min

Perm Press

Medium

(No change)

Normal dry 32 min 29 min 3 min

Bedding

High

(No change)

Normal dry 50 min 47 min 3 min

Delicates

Extra Low

(No change)

Normal dry 34 min 33 min 1 min

Sanitize

High

(No change)

Very dry

(No change)

60 min 55 min 5 min

Eco Normal

High

(No change)

Normal dry

(No change)

72 min 69 min 3 min

Wool

Low

(No change)

Normal dry

(No change)

28 min 27 min 1 min

Manual Dry

Air Fluff

(No change)

20 min - 20 min

Quick Dry

High

(No change)

30 min 27 min 3 min

Time Dry High

(No change)

40 min 37 min 3 min

Steam

Cycles

Wrinkle Away

High

(No change)

20 min 19 min 1 min

Refresh

High

(No change)

15 min 14 min 1 min

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec7:40DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec7:40 2012-07-13  1:07:532012-07-13  1:07:53

warranty _41

warranty (U.S.A)

SAMSUNG DRYER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) Year All Parts and Labor

Two (2) Years Control Board Parts

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the United States.

To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service

procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or

SAMSUNG’s authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability

within the contiguous United States.

In-home service is not available in all areas.

To receive in-home service, product must be unobstructed and accessible to the service agent.

If service is not available, SAMSUNG may elect to provide transportation of the product to and from an

authorized service center.

SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein,

with new or reconditioned parts or products if found to be defective during the limited warranty period

specified above.

All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG.

Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is

longer.

This limited warranty covers manufacturing defects in materials and workmanship encountered in normal,

noncommercial use of this product and shall not apply to the following: damage that occurs in shipment;

delivery and installation; applications and uses for which this product was not intended; altered product or

serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning, or other

acts of nature or God; use of products, equipment, systems, utilities, services, parts, supplies, accessories,

applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG

that damage this product or result in service problems; incorrect electrical line voltage, fluctuations and

surges; customer adjustments and failure to follow operating instructions, maintenance and environmental

instructions that are covered and prescribed in the instruction book; product removal and reinstallation;

problems caused by pest infestations.

This limited warranty does not cover problems resulting from incorrect electric current, voltage or supply,

light bulbs, house fuses, house wiring, cost of a service call for instructions, or fixing installation errors.

SAMSUNG does not warrant uninterrupted or error-free operation of the product.

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec8:41DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec8:41 2012-07-13  1:07:532012-07-13  1:07:53

42_ warranty

Except as set forth herein, there are no warranties on this product either express or implied, and samsung

disclaims all warranties including, but not limited to, any implied warranties of merchantability, infringement

or fitness for a particular purpose.

No warranty or guarantee given by any person, firm, or corporation with respect to this product shall be

binding on samsung.

Samsung shall not be liable for loss of revenue or profits, failure to realize savings or thter benefits, or

any other special, incidental or consequential damages caused by the use, misuse, or inability to use this

product, regardless of the legal theory on which the claim is based, and even if samsung has been advised

of the possibility of such damages.

Nor shall recovery of any kind against samsung be greater in amount than the purchase price of the product

sold by samsung and causing the alleged damage.

Without limiting the foregoing, purchaser assumes all risk and liability for loss, damage, or injury to

purchaser and purchaser’s property and to others and their property arising out of the use, misuse,

or inability to use this product. This limited warranty shall not extend to anyone other than the original

purchaser of this product, is nontransferable and states your exclusive remedy.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation

of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This

warranty gives you specific rights, and you may also have other rights, which vary from state to state.

To obtain warranty service, please contact SAMSUNG at:

Samsung Electronics America, Inc.

85 Challenger Road Ridgefield Park, NJ 07660

1-800-SAMSUNG(726-7864)

www.samsung.com

warranty (U.S.A)

DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec8:42DV433ETGJWR_A1_02836H-01_EN_20120713.indd Sec8:42 2012-07-13  1:07:532012-07-13  1:07:53

warranty _43

warranty (CANADA)

SAMSUNG DRYER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) year part and labor

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the Canada.

To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service

procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or

SAMSUNG’s authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability

within the Canada.