Transcripción de documentos

RX-595 Natural Sound Stereo Receiver 80W + 80W (8Ω) RMS Output Power, 0.019% THD, 20–20,000 Hz High Dynamic Power, Low Impedance Drive Capability Continuously Variable Loudness Control CD DIRECT AMP Switch to Reproduce the Purest CD Sound PURE DIRECT Switch to Reproduce the Purest Source Sound 40-Station Random Access Preset Tuning Automatic Preset Tuning Preset Station Shifting Capability (Preset Editing) IF Count Direct PLL Synthesizer Tuning System Video Signal Input/Output Capability Remote Control Capability Thank you for selecting this YAMAHA stereo receiver. CAUTION RISK OF ELECTRIC SHOCK CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. OWNER’S MANUAL CONTENTS Safety Instructions ................... 2 Supplied Accessories .............. 3 Connections ............................. 4 Basic Operations ...................... 7 Tuning Operations .................. 10 Preset Tuning ......................... 11 Remote Control Transmitter ... 13 Troubleshooting ...................... 15 Specifications ......................... 16 IMPORTANT! Please record the serial number of this unit in the space below. • Explanation of Graphical Symbols Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.  SAFETY INSTRUCTIONS 1 2 3 4 5 6 6A 7 8 9 10 11 12 13 14 Read Instructions – All the safety and operating instructions should be read before the unit is operated. Retain Instructions – The safety and operating instructions should be retained for future reference. Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to. Follow Instructions – All operating and other instructions should be followed. Water and Moisture – The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. Carts and Stands – The unit should be used only with a cart or stand that is recommended by the manufacturer. A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. Heat – The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. Cleaning – The unit should be cleaned only as recommended by the manufacturer. Nonuse Periods – The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. Object and Liquid Entry – Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit. 15 Damage Requiring Service – The unit should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normally or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 16 Servicing – The user should not attempt to service the unit 17 18 19 beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. Power Lines – An outdoor antenna should be located away from power lines. Grounding or Polarization – Precautions should be taken so that the grounding or polarization is not defeated. Outdoor Antenna Grounding – If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. EXAMPLE OF ANTENNA GROUNDING MAST ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) NEC – NATIONAL ELECTRICAL CODE Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. 2 Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.  Caution: Read this before operating your unit 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water. Do not operate the unit upside-down. It may overheat, possibly causing damage. Never open the cabinet. If something drops into the set, contact your dealer. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves. 2 3 4 5 6 7 8 9 10 Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Always set the VOLUME control to “– ∞” before starting the audio source play. Increase the volume gradually to an appropriate level after the play back has been started. To prevent lightning damage, pull out the power cord and remove the antenna cable during an electrical storm. Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. AC outlet Do not connect audio equipment to the AC outlet on the rear panel if that equipment requires more power than the outlet is rated to provide. FCC INFORMATION 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained. ● Remote Control Transmitter ● Batteries (size AA, R6, UM-3) ● Indoor FM Antenna ● AM Loop Antenna 3  CONNECTIONS Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made. CONNECTIONS WITH OTHER COMPONENTS When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit. Video cassette recorder or Tape deck 2 Turntable CD player Speakers A Left VIDEO IN VIDEO OUT AUDIO OUT AUDIO IN OUTPUT GND OUTPUT Right (U.S.A. model) GND REMOTE CONTROL CD IN FM ANT 75Ω UNBAL. TAPE PB OUT SPEAKERS TAPE 1 GND MONITOR OUT AM ANT PHONO 50 kHz IN TAPE PB VCR VCR / TAPE 2 OUT REC OUT 9 kHz SWITCHED l20V 60Hz l00W MAX. TOTAL A A OR B : 6ΩMIN./SPEAKER A B : l2ΩMIN./SPEAKER B l00 kHz l0 kHz FM AM FREQUENCY STEP LD / TV LD / TV AUDIO SIGNAL VIDEO SIGNAL AC OUTLETS REC OUT AUDIO SIGNAL Monitor TV LD player, TV tuner, etc. LINE OUT LINE IN AUDIO OUT VIDEO OUT VIDEO IN To AC outlet Tape deck 1 : Refer to “ABOUT THE ACCESSORY TERMINALS” on page 5. * If a tape deck is connected to the VCR/TAPE 2 (AUDIO SIGNAL) terminals, there is no connection to the VCR (VIDEO SIGNAL) terminals. 4 Left Right Speakers B  CONNECTING SPEAKERS Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass. Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit and/or speakers. Notes • Use speakers with the specified impedance shown on the rear of this unit. • One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals. • Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal. How to connect: Red: positive (+) Black: negative (–) ➀ Unscrew the knob. ➁ Insert the bare wire. 2 1 3 [Remove approx. 5mm (1/4”) insulation from the speaker wires.] ➂ Tighten the knob and secure the wire. ABOUT THE ACCESSORY TERMINALS AC OUTLET(S) (SWITCHED) (U.S.A., Canada and General models) ...........................................................2 SWITCHED OUTLETS (Australia model) ................................. 1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit’s POWER switch or the provided remote control transmitter’s POWER key. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLET(S) is 100 watts. GND terminal (For turntable use) Connecting the ground wire of the turntable to this terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected. For Custom Installer REMOTE CONTROL (IN, OUT) terminals (U.S.A. and Canada models only) These terminals are used for custom installation system. When this unit is connected to the components for custom installation system, you can operate this unit with the system remote control. Connect the REMOTE CONTROL IN terminal to the EMITTER terminal (FROM INDEPENDENT ZONE, FROM ALL ZONE or FROM SELECTED ZONE) of the YAMAHA Master Zone Controller MCX-10. By connecting the REMOTE CONTROL OUT terminal to the REMOTE CONTROL IN terminal of the other component, you can also operate it with the system remote control. In this way, up to 6 components can be connected in series. 5  ANTENNA CONNECTIONS ● ● Each antenna should be connected to the designated terminals correctly, referring to the following diagram. Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. Outdoor FM antenna Indoor FM antenna (included) Outdoor AM antenna AM loop antenna (included) REMOTE CONTROL IN FM ANT 75Ω UNBAL. OUT 300-ohm feeder GND MONITOR OUT AM ANT IN PHONO 50 kHz VCR 9 kHz OUT l00 kHz l0 kHz FM AM FREQUENCY STEP 75-ohm coaxial cable LD / TV AUDIO SIGNAL VIDEO SIGNAL AU 75-ohm/300-ohm antenna adapter Ground Connecting the AM loop antenna ➀ Orient so that the best reception is obtained. ➂ ➁ * The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit. GND terminal For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. Notes ● When connecting the indoor FM antenna, insert its connector into the FM ANT terminal firmly. ● 6 If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, coaxial cable is preferable.  BASIC OPERATIONS 7 2 1, 6 4 7 3 TO PLAY A SOURCE 1 4 VOLUME l8 l6 20 l4 Select the speakers to be used. l2 24 SPEAKERS l0 28 8 34 6 4 40 A B ON ON OFF OFF 3 50 2 60 l 70 0 –dB ∞” position. Set to the “ 2 Turn the power on. * If you use two speaker systems, press both the A and B switches. 5 POWER Play the source. (For detailed information on the tuning operation, refer to page 10.) 6 VOLUME l8 l6 20 l4 l2 24 l0 28 8 34 3 6 4 40 Select a desired input source. (For video sources, turn the TV/monitor ON.) 3 50 2 60 l 70 0 –dB INPUT TUNER TAPE 1 VCR/ TAPE 2 CD Adjust to the desired output level. PHONO LD/TV * The name of the selected input source position will appear in the display. (For “TUNER”, the tuning mode will appear in the display.) * Note that selecting each input source position accesses the source which is connected to the corresponding input terminals on the rear panel. 7 If desired, adjust the BASS, TREBLE, BALANCE and LOUDNESS controls, etc. (Refer to page 9.) To turn off the power Press the POWER switch again. 7  3 1 3, 5 TO RECORD A SOURCE TO TAPE (OR DUB FROM A TAPE TO ANOTHER) 1 4 Select the source to be recorded. REC OUT Set the tape deck (or VCR) to be used for recording in the recording mode. TUNER TAPE 1 VCR/TAPE 2 CD PHONO 5 LD/TV 2 To monitor the sound (and/or picture) to be recorded, select the tape deck (or VCR) being used for recording with the INPUT selector. Play the source. INPUT TUNER TAPE 1 3 VCR/ TAPE 2 Confirm the source by selecting it with the INPUT selector and turning up the VOLUME control. CD PHONO LD/TV VOLUME INPUT l8 TUNER TAPE 1 VCR/ TAPE 2 l6 20 CD l4 l2 24 l0 28 8 PHONO 34 LD/TV 6 4 40 3 50 2 60 l 70 0 –dB Notes If you want to enjoy another source while recording, select it with the INPUT selector. ● VOLUME, BASS, TREBLE, BALANCE, LOUDNESS controls, CD DIRECT AMP switch and PURE DIRECT switch settings have no effect on the material being recorded. ● When you listen with headphones Connect the headphones to the PHONES jack. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position. 8 PHONES  Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused from speaker location or listening room conditions. Selecting the SPEAKER system Because one or two speaker systems can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B, or both at once. BALANCE 0 l SPEAKERS l 2 2 3 4 5 R Adjusting the BASS and TREBLE controls BASS l 0 TREBLE l l 2 3 l 2 3 4 5 0 2 3 4 OFF OFF This control provides compensation for the human ears’ loss of sensitivity to high and low-frequency ranges at low volume. This control is adjustable to retain full tonal range at any volume level. 3 4 5 Adjusting the continuously variable LOUDNESS control 4 5 5 1 LOUDNESS l : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. Set to the “FLAT” position. FLAT 30 dB 2 BASS B ON 4 L 5 2 A ON 3 l0 3 9 8 4 5 2 6 7 VOLUME l8 l6 l4 20 l2 24 l0 28 8 34 Set to the loudest listening level that you would listen to. 6 4 40 3 50 2 60 l 70 0 –dB Using the CD DIRECT AMP switch You can enjoy the purest possible CD sound from your CD player by setting this switch so that the indicator illuminates. By doing so, CD’s input signals are sent to the built-in amplifier special for CD directly bypassing the INPUT selector, BASS, TREBLE, BALANCE and LOUDNESS controls, and then sent to the power amplifier. This signal routing reproduces the purest CD sound eliminating any alterations to the CD signals. CD DIRECT AMP Note If both the CD DIRECT and PURE DIRECT switches are on, only the CD DIRECT switch will function. 3 LOUDNESS l FLAT 30 dB 2 Turn until the desired volume is gained. l0 3 9 4 8 5 6 7 Using the PURE DIRECT switch You can enjoy the purest possible sound from your audio sources by setting this switch so that the indicator illuminates. By doing so, the audio signals bypass the BASS, TREBLE, BALANCE and LOUDNESS controls, thus eliminating any alterations to the audio signals. PURE DIRECT 9  TUNING OPERATIONS Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). 3 2 1 AUTOMATIC TUNING 1 MANUAL TUNING Select the reception band (FM or AM) while watching the display. 1 FM/AM FM/AM or FM 2 Select the reception band (FM or AM) while watching the display. AM FM 2 TUNING MODE AUTO/MAN’L MONO DOWN TUNING “AUTO TUNING” goes off. 3 UP Tune to a desired station manually. DOWN To tune to a higher frequency, press the right side once. To tune to a lower frequency, press the left side once. * If the station where tuning search stops is not the desired one, press again. * If the tuning search does not stop at the desired station (because the signals of the station are weak), change to the MANUAL TUNING method. AM TUNING MODE AUTO/MAN’L MONO AUTO TUNING 3 or TUNING UP * To continue tuning search, press and hold the button. Note If you tune to an FM station manually, it is received in monaural mode automatically to increase the signal quality. Display information ➀ ➂ STEREO PRESET FM MHz 0 20 40 60 ➂ 10 ➀ ➁ ➁ l00 Displays the band and frequency of the received station. Lights up when an FM stereo broadcast is received in stereo. Indicates the signal level of the received station.  PRESET TUNING MANUAL PRESET TUNING This unit can store station frequencies (selected by tuning operation) by using the preset station buttons. With this function, you can select any desired station by only pressing the corresponding preset station button. Up to 40 stations (8 stations x 5 pages) can be stored. 2, 1 4, 2 (Preset station buttons) 3 To recall a preset station To store stations 1 Tune to a desired station. (Refer to the previous page for tuning procedure.) 1 Select the page of preset station buttons. A/B/C/D/E 2 PRESET Select a desired page (A – E) of preset station buttons while watching the display. A/B/C/D/E PRESET 2 Select the desired preset station button. l 3 2 3 PRESET STATIONS 4 5 6 7 8 MEMORY MEMORY MAN’L/AUTO FM PRESET Flashes on and off for about 5 seconds. 4 Press a preset station button before “MEMORY” goes off from the display. l 2 3 PRESET STATIONS 4 5 6 7 8 PRESET FM MHz 0 20 40 60 l00 Shows the displayed station has been programmed to A1. * * Notes ● A new setting can be programmed in place of the former one. ● For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency. Memory back-up The memory back-up circuit prevents the programmed data from being lost even if the POWER switch is set off or the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simply following the PRESET TUNING steps. In the same way, program other stations to A2, A3 ... A8. You can program more stations to the preset station buttons on other pages in the same way by selecting other pages in step 2. 11  AUTOMATIC PRESET TUNING You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 11. 2 3 1 To store stations 1 When the automatic preset tuning is finished The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure of the section “To recall a preset station” on page 11. FM/AM FM To recall a preset station 2 Simply follow the procedure of the section “To recall a preset station” on page 11. MEMORY PRESET MAN’L/AUTO FM AUTO TUNING MEMORY Press and hold for about 3 seconds. 3 DOWN Flashes. TUNING UP To tune to higher frequencies, press right side once. To tune to lower frequencies, press left side once. * If the TUNING button is not pressed, in a while, the automatic preset tuning begins automatically toward higher frequencies. The automatic preset tuning begins from the frequency currently displayed. Received stations are programmed to A1, A2 ... A8 sequentially. * If more than 8 stations are received, they are also programmed to the preset station numbers on other pages (B, C, D and E) in that order. If you want to store the first station received by the automatic preset tuning to a desired preset station number. If, for example, you want to store the first received station to C5, select “C5” by using the A/B/C/D/E button and the preset station buttons after pressing the MEMORY button in step 2. Then press the TUNING button. The first received station is stored to C5, and next stations to C6, C7 ... sequentially. If stations are stored up to E8, the automatic preset tuning is finished automatically. 12 Notes ● You can replace a preset station by another FM or AM station manually by simply following the procedure of the section “To store stations” on page 11. ● If the number of received stations is not enough to be stored up to E8, the search is finished automatically after searching through all frequencies. ● With this function, only FM stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune to it in monaural manually and program it by following the procedure of the section “To store stations” on page 11.  EXCHANGING PRESET STATIONS You can exchange the places of two preset stations with each other as shown below. 2, 4 Example) If you want to shift the preset station on E1 to A5, and vice versa. 1 2 Recall the preset station on E1 (by following the method of “To recall a preset station” on page 11). EDIT 4 EDIT PRESET MEMORY Flashes 3 Next, recall the preset station on A5 by following the same method with step 1. PRESET MEMORY Flashes Shows the exchange of stations is completed. REMOTE CONTROL TRANSMITTER NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery installation Remote control transmitter operation range 2 1 Remote control sensor 3 Within approximately 6 m (19.7 feet) Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes ● Use only AA, R6, UM-3 batteries for replacement. ● Be sure the polarities are correct. (See the illustration inside the battery compartment.) ● Remove the batteries if the remote control transmitter will not be used for an extended period of time. ● If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. 30° 30° Notes ● There should be no large obstacles between the remote control transmitter and the main unit. ● If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting. 13  The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the CD player and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this remote control transmitter will also control various functions of each component. KEY FUNCTIONS For Control of This Unit POWER PHONO Turns the power on/off. SLEEP SKIP PLAY SEARCH PAUSE/STOP DISC SKIP — PRESET Selects preset station number. * +: Selects higher preset station number. –: Selects lower preset station number. A/B/C/D/E: Selects the page (A – E) of preset stations. DIR A CD + DECK A/B A/B/C/D/E TUNER DIR B TAPE 1 STOP Selects input source. VCR/ TAPE 2 PLAY REC/PAUSE The power to this unit is automatically turned off one hour after this key is pressed (so that “SLEEP” is illuminated on in the display). REC MUTE LD/TV + — VOLUME Turns the master volume level up/down. For Other Component Control Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their function will be the same. On each key function, refer to the corresponding instruction on your component’s manual. POWER PHONO SLEEP SKIP PLAY SEARCH — PRESET DIR A Controls the tape deck. * DIR A, B and DECK A/B are applicable only to a double cassette tape deck. * For a single cassette deck with automatic reverse function, pressing DIR A will reverse the direction of tape running. 14 PAUSE/STOP DISC SKIP + DECK A/B A/B/C/D/E TUNER DIR B TAPE 1 VCR/ TAPE 2 PLAY REC/PAUSE CD STOP REC MUTE LD/TV — VOLUME + Controls the compact disc player. * DISC SKIP is applicable only to a compact disc changer.  TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM Firmly plug in the power cord. No sound or no picture. Incorrect output cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Appropriate input source is not selected. Select an appropriate input source with the INPUT selector. The SPEAKERS switches are not set properly. Set the SPEAKERS switch which corresponds to the speakers to be used to the ON position. Speaker connections are not secure. Secure the connections. The protection circuit has functioned because of short circuit etc. Turning the unit off and then on will reset the protection circuit. The SLEEP timer functioned. Cancel the SLEEP timer function. Incorrect setting of the BALANCE control. Adjust it to the appropriate position. Incorrect cord connections. Connect the cords properly. If the problem persists, the cords may be defective. There is a lack of bass, and no ambience. The + and – wires are connected in reverse at the amplifier or speakers. Connect the speakers wires in the correct phase (+ and –). Sound “hums”. Incorrect cord connections. Firmly connect the audio plugs. If the problem persists, the cords may be defective. No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit. The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The player should be connected to the unit through the MC head amplifier. The volume level cannot be increased, or sound is distorted. The power to the component connected to the REC OUT terminals of this unit is off. Turn the power to the component on. Sound level is low. The LOUDNESS control is functioning. Set the LOUDNESS control to the FLAT position. The INPUT selector will not function though it is turned. The CD DIRECT AMP switch is ON. Switch off the CD DIRECT AMP switch. Using the BASS, TREBLE, BALANCE and LOUDNESS controls does not affect the tone. The CD DIRECT AMP or PURE DIRECT switch is ON. The CD DIRECT AMP and PURE DIRECT switches must be switched OFF to use those controls. FM stereo reception is noisy. Because of the characteristics of FM stereo broadcasts, this is limited to cases where the transmitter is too far away or the antenna input is poor. Check the antenna connections. Try using a multiple element FM antenna. There is distortion and clear reception cannot be obtained even with a good FM antenna. There is multipath interference. Adjust antenna placement to eliminate multipath interference. A desired station cannot be tuned in with Auto tuning. The station is too weak. Use Manual tuning mode. Use a high quality directional FM antenna. A desired station cannot be tuned in with Auto tuning. Weak signal or loose antenna connections. Tighten the AM loop antenna connections and rotate it for best reception. There are continuous crackling and hissing noises. Noises will result from lightning, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat but it is difficult to eliminate all noise. There are buzzing and whining noises (especially in the evening). A television set is being used nearby. Relocate this unit away from the TV. The remote control transmitter does not work. Direct sunlight or lighting (of an inverter type of flourescent lamp etc.) is striking the remote control sensor of the main unit. Change the position of the main unit. The distance or range within which the remote control transmitter can be used decreases. The batteries of this remote control transmitter are too weak. Replace the batteries with new ones. Only one side speaker outputs the sound. Amplifier REMEDY Power cord is not plugged in or is not completely inserted. The sound suddenly goes off. FM CAUSE The unit fails to turn on when the POWER switch is pressed. Remote control transmitter AM Use Manual tuning mode. 15  SPECIFICATIONS AUDIO SECTION Minimum RMS Output Power per Channel 8 ohms, 20 Hz to 20 kHz, 0.019% THD ...................................................80W+80W 6 ohms, 20 Hz to 20 kHz, 0.038% THD ...................................................90W+90W Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) 8/6/4/2 ohms ...................120/140/180/200W Power Band Width 8 ohms, 40W, 0.038% THD ..........................................10 Hz to 50 kHz Damping Factor (SPEAKERS A) 8 ohms, 20 Hz to 20 kHz ...........240 or more Maximum Power (EIAJ) 1 kHz, 10% THD [General model only] 8 ohms .................................................130W 6 ohms .................................................150W Input Sensitivity/Impedance PHONO MM .....................2.5 mV/47 k-ohms CD/TAPE/LD·TV/VCR......150 mV/47 k-ohms Maximum Input Signal (1 kHz, 0.003% THD) PHONO MM......................................115 mV Output Level/Impedance REC OUT .........................150 mV/470 ohms Headphone Jack Rated Output/Impedance (RL = 8ohms, 0.019% THD) Output Level ..........................................0.3V Impedance.....................................680 ohms Frequency Response (20 Hz to 20 kHz) CD/TAPE/LD·TV/VCR .....................0±0.5 dB RIAA Equalization Deviation PHONO MM....................................0±0.3 dB Total Harmonic Distortion PHONO MM to REC OUT 20 Hz to 20 kHz, 3V........................0.003% CD/TAPE/LD·TV/VCR to SP OUT 20 Hz to 20 kHz, 40W/8 ohms........0.008% Intermodulation Distortion CD/TAPE/LDzTV/VCR (Rated output/8 ohms) .....................0.01% Signal-to-Noise Ratio (IHF-A Network) PHONO MM (5 mV Input Shorted) ......88 dB CD/TAPE/LD·TV/VCR (Input Shorted, EFFECT OFF) ...................................110 dB Residual Noise (IHF-A Network) CD DIRECT AMP ON ..........................35 µV PURE DIRECT ON ..............................90 µV YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA Channel Separation (Vol. –30 dB, EFFECT OFF) CD/TAPE/LD·TV/VCR (Input 5.1 k-ohms Terminated 1 kHz/ 10 kHz)....................................65 dB/50 dB Tone Control Characteristics BASS: Boost/cut ................±10 dB (20 Hz) Turnover Frequency .........(350 Hz) TREBLE: Boost/cut...........±10 dB (20 kHz) Turnover Frequency.....(3.5 kHz) Continuous Loudness Control ..............................................–30 dB (1 kHz) (Level related equalization) Gain Tracking Error (0 to –60 dB) ............2 dB AM SECTION Tuning Range [U.S.A., Canada and General models] ...........................................530 to 1,710 kHz [Australia model] ................531 to 1,611 kHz Usable Sensitivity .............................100 µV/m Selectivity ...............................................32 dB Signal-to-Noise Ratio .............................50 dB Image Response Ratio...........................40 dB Spurious Response Ratio.......................50 dB Harmonic Distortion (400 Hz) ..................0.3% AUDIO SECTION Input Level/Impedance ...........1 Vp-p/75 ohms Output Level/Impedance ........1 Vp-p/75 ohms Output Level/Impedance FM (100% mod., 1 kHz) .....................................500 mV/2.2 k-ohms AM (30% mod., 400 Hz) .....................................150 mV/2.2 k-ohms FM SECTION GENERAL Tuning Range [U.S.A. and Canada models] .........................................87.5 to 107.9 MHz [Australia and General models] .........................................87.5 to 108.0 MHz 50 dB Quieting Sensitivity (IHF, 75 ohms) Mono ................................1.55 µV (15.1 dBf) Stereo .................................21 µV (37.7 dBf) Usable Sensitivity (75 ohms) (30 dB S/N Quieting, 1 kHz, 100% mod.) ..........................................0.8 µV (9.3 dBf) DIN, Mono (S/N 26 dB).......................0.9 µV DIN, Stereo (S/N 46 dB) ......................24 µV Image Response Ratio...........................45 dB IF Response Ratio..................................80 dB Spurious Response Ratio.......................70 dB AM Suppression Ratio............................55 dB Capture Ratio ........................................1.5 dB Alternate Channel Selectivity ................85 dB Signal-to-Noise Ratio (IHF) Mono/Stereo .............................80 dB/75 dB Harmonic Distortion (1 kHz) Mono/Stereo ...................................0.1/0.2% Stereo Separation (1 kHz)......................50 dB Frequency Response 20 Hz to 15 kHz .............................0 ±1.5 dB Power Supply [U.S.A. and Canada models] ............................................AC 120V, 60 Hz [Australia model]..................AC 240V, 50 Hz [General model] ..................AC 110/120/220/240V, 50/60 Hz Power Consumption [U.S.A. model].....................................190 W [Canada model]......................250 W/320 VA [Australia and General models] ...........210W AC Outlets 2 SWITCHED OUTLETS [U.S.A., Canada and General models] ..........................................100W max. total 1 SWITCHED OUTLET [Australia model] ...............100W max. total Dimensions (W x H x D) ........................................435 x 146 x 386 mm (17-1/8” x 5-3/4” x 15-3/16”) Weight ...........................9.5 kg (20 lbs. 14 oz.) Accessories ..........................AM loop antenna Indoor FM antenna Remote control transmitter Batteries VIDEO SECTION Specifications are subject to change without notice. ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, D-25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA VS 98730