Lennox S40 Smart Room Sensor Guía del usuario

Tipo
Guía del usuario
Lennox® Smart Room Sensor Installer Quick Start Guide
508299-01 December 2022
Scan QR Code for Installation and
Setup Guide
Français / Español
IMPORTANT
DO NOT paint the smart device. Doing so will prevent the occupancy
sensor and other components from functioning correctly.
Sensor Stand
Pairing and Factory
Reset Button
Relative Humdity
and Temperature
Sensors
Front Cover (removable)
Battery compartment
for two AA lithium batteries
Opening Latch (Depress
and pull tab to
remove front cover)
LED Light Pipe
Recessed Factory
Reset Button
Occupancy
Fresnel Lens
NOTE: LED light pipe is not visible on top of plastic surface.
User will see illumination on the front plastic when LED is on.
Occupancy Sensor
Figure 1. Sensor LED Indicator, Buttons, Sensor Vents, Battery
Compartment Locations
1. Download and install the Lennox® Smart Technician Service App if
not already installed on your mobile device.
2. The following procedure is assuming the Lennox® S40 Smart
Thermostat has already been commissioned. From the thermostat
home screen, go to Menu > Settings > Advanced Settings > View
Support Service Control Center and select Connect To Lennox
Smart Technician App.
3. The thermostat will start broadcasting its Thermostat ID.
4. Start the Lennox® Smart Technician App and follow the screen
prompts until you reach Service Center.
5. To add a smart device, select Equipment Settings > Add Device.
6. Open the case and remove the insulation tape from the AA lithium
batteries. Once the tape is removed the smart device will start
broadcasting its ID automatically.
NOTA: The SRS will broadcast its ID for three minutes. To restart the
broadcast ID, press the pairing button for two seconds.
7. Follow the screen prompts to add the smart device.
8. Conrm the desired sensor location has adequate signal strength.
No LED light indicates the smart device is within range, blue LED
light indicates weak signal. The Lennox® Wireless Extender (sold
separately) is recommended when a location does not have a strong
signal strength.
9. Install the smart device on an interior wall (see Figure 2) at a minimum
height of 5 feet (1.52 meters) or place on the stand. For more
recommendations on placement of room sensors, please download the
installation guide.
Minimum 6” (15.24 cm)
from corner
Minimum 5’ (1.52 m)
from oor
Figure 2. Installation Considerations
10. It is recommended that the smart device is installed on a wall to ensure it
will not be lost or damaged. Use the provided screws and wall anchors.
11. A wall template is also included for the smart device installation.
12. If not installed on a wall, use the included stand. Use the stand to place
the smart device above the ground on a table or shelf out of reach of
children and pets.
13. Walk the homeowner through use of the smart device including where
to nd and download the Lennox® Smart Thermostat App. Refer to
the Lennox® S40 Smart Thermostat User Guide on how to use the
smart device.
lennoxsmartertogether.com/dealer-access
lennoxsmartertogether.com/spanish-french
Guía de instalación rápida para el Instalador del Sensor de
Cuarto Inteligente Lennox®
508299-01 Diciembre de 2022
Escanee el código QR para la Guía de instalación y conguración Français / Español
IMPORTANTE
NO pinte el dispositivo inteligente. El hacerlo podría impedir que el sensor de ocupación y
otros componentes funcionen correctamente.
Lente de Fresnel
de ocupación
Tapa delantera (removible)
Tubo de luz LED
Retén de apertura (presionar y
halar la pestaña
para quitar la tapa delantera)
NOTA: El tubo de luz LED no es visible sobre la supercie de plástico.
El usuario verá la iluminación en el plástico delantero cuando el LED está encendido.
Botón de emparejamiento y
reinicio de fábrica Botón de reinicio de
fábrica empotrado
Pedestal para el sensor
Compartimiento para
dos baterías AA de litio
Sensor de ocupación
Detección de
humedad
relativa y
temperatura
Figura 1. Ubicación del indicador LED del sensor, botones, oricios
de ventilación de los sensores y compartimiento de las baterías
1. Descargue e instale la Aplicación Servicio de Técnico Inteligente de
Lennox en su dispositivo móvil si todavía no lo ha hecho.
2. El siguiente procedimiento supone que ya se puso en servicio el Termostato
inteligente Lennox® S40. Desde la pantalla inicial del termostato, vaya a
Menú > Conguración > Ajustes avanzados > Ver el Centro de control
de servicio de apoyo y seleccione Conectar a la aplicación Técnico
inteligente de Lennox.
3. El termostato comenzará a transmitir su ID.
4. Active la Aplicación Técnico Inteligente de Lennox® y siga las
indicaciones en la pantalla hasta llegar a Centro de servicio.
5. Para añadir un dispositivo inteligente, seleccione Ajustes al equipo >
Añadir dispositivo.
6. Abra la caja y quite la cinta de aislamiento de las baterías AA de litio.
Una vez que haya quitado la cinta, el dispositivo inteligente comenzará a
transmitir su ID automáticamente.
NOTA: El SRS transmitirá su ID durante tres minutos. Para reiniciar la ID
de transmisión, presione el botón de emparejamiento durante dos
segundos.
7. Siga las indicaciones en la pantalla para añadir el dispositivo inteligente.
8. Conrme que en la ubicación deseada del sensor y la intensidad de la
señal es adecuada. Luz LED apagada indica que el dispositivo inteligente
está dentro del rango, luz LED azul indica una señal débil. Se recomienda
usar un Extensor Inalámbrico Lennox® (se vende separado) cuando en
una ubicación la señal no es de alta intensidad.
9. Instale el dispositivo inteligente en una pared interior (consulte la Figura 2) a
una altura mínima de 5 pies (1,52 metros) o colóquelo sobre el soporte. Para
obtener más recomendaciones sobre la colocación de sensores de habitación,
descargue la guía de instalación.
Minimum 6” (15.24 cm)
from corner
Minimum 5’ (1.52 m)
from oor
Figura 2. Consideraciones de instalación
10. Se recomienda que el dispositivo inteligente se instale en una pared para que
no se extravíe o se dañe. Use los tornillos y dispositivos de anclaje en la pared
proporcionados.
11. También se incluye una plantilla de pared para la instalación del dispositivo
inteligente.
12. Si no se instala en una pared, use el pedestal incluido. Use el pedestal
para colocar el dispositivo inteligente encima del piso sobre una mesa o
estante fuera del alcance de los niños o mascotas.
13. Explique al propietario cómo usar el dispositivo inteligente, incluyendo
dónde encontrar y descargar la Aplicación Termostato Inteligente de
Lennox
®
. Consulte la Guía del usuario del termostato inteligente S40
®
sobre cómo usar el dispositivo inteligente.
lennoxsmartertogether.com/dealer-access lennoxsmartertogether.com/spanish-french
  • Page 1 1
  • Page 2 2

Lennox S40 Smart Room Sensor Guía del usuario

Tipo
Guía del usuario

En otros idiomas