Samsung DVG52M7750V/A3 El manual del propietario

Marca: Samsung

Modelo: DVG52M7750V/A3

Categoría: Secadoras de ropa eléctricas

Tipo: El manual del propietario

Dryer

User manual

DVE(G)52M775**

DV7750M-03170Y-00_EN.indd 1 2016-12-28  11:43:16

Contents

English2

Contents

Safety information 4

What you need to know about the safety instructions 4

Important safety symbols 4

Important safety precautions 5

Warnings 8

Cautions 8

Installation requirements 10

Key installation requirements 10

Location considerations 10

Ducting requirements 11

Exhausting requirements 12

Gas requirements 13

Electrical requirements 14

Installation 17

What’s included 17

Step-by-step installation 19

Vent blockage test 25

Exhaust ducting guide 27

Switching the door position 27

Before you start 30

Sort and load 30

Functional prerequisite 30

Operations 31

Feature panel 31

Simple steps to start 34

Cycle overview 35

Cycle guide 36

Special features 37

DV7750M-03170Y-00_EN.indd 2 2016-12-28  11:43:16

Contents

English 3

Maintenance 39

Vent sensor (applicable models only) 39

Cleaning 40

Troubleshooting 41

Checkpoints 41

Information codes 43

Specications 45

Fabric care chart 45

Protecting the environment 46

Specication sheet 47

Cycle chart 48

DV7750M-03170Y-00_EN.indd 3 2016-12-28  11:43:16

Safety information

SAVE THESE INSTRUCTIONS

English4

Safety information

Congratulations on your new Samsung dryer. This manual contains important information

on the installation, use and care of your appliance. Please take some time to read this

manual to take full advantage of your dryer’s many benets and features.

What you need to know about the safety instructions

Please read this manual thoroughly to ensure that you know how to safely and efciently

operate the extensive features and functions of your new appliance. Please store the

manual in a safe location close to the appliance for future reference. Use this appliance

only for its intended purpose as described in this instruction manual.

Warnings and Important Safety Instructions in this manual do not cover all possible

conditions and situations that may occur. It is your responsibility to use common sense,

caution and care when installing, maintaining and operating your dryer.

Because the following operating instructions cover various models, the characteristics of

your dryer may differ slightly from those described in this manual and not all warning

signs may be applicable. If you have any questions or concerns, contact your nearest

service center or nd help and information online at www.samsung.com.

Important safety symbols

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury, death and/or

property damage.

CAUTION

Hazards or unsafe practices that may result in personal injury and/or property damage.

NOTE

Indicates that a risk of personal injury or material damage exists.

These warning signs are here to prevent injury to yourself and others.

Please follow them explicitly.

After reading this manual, store it in a safe place for future reference.

Read all instructions before using the appliance.

As with any equipment that uses electricity and moving parts, potential hazards exist.

To safely operate this appliance, familiarize yourself with its operation and exercise care

when using it.

DV7750M-03170Y-00_EN.indd 4 2016-12-28  11:43:16

Safety information

SAVE THESE INSTRUCTIONSSAVE THESE INSTRUCTIONS

English 5

WARNING - Gas Appliances:

• State of California Proposition 65 Warnings (US only)

This product contains chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

• Gas appliances can cause low-level exposure to Proposition 65 listed substances,

including but not limited to, benzene, carbon monoxide, formaldehyde and soot,

substances resulting from the incomplete combustion of natural gas or LP fuels.

WARNING - Risk of Fire

• Clothes dryer installation must be performed by a qualied installer.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• Do not install a clothes dryer with exible plastic venting materials. If exible metal

(foil type) duct is installed, it must be of a specic type identied by the appliance

manufacturer as suitable for use with clothes dryers. Flexible venting materials are

known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airow and increase the risk of re.

• To reduce the risk of severe injury or death, follow all installation instructions.

• Save these instructions.

Important safety precautions

WARNING

To reduce the risk of re, electric shock, or injury to persons when using your appliance,

follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in,

or spotted with gasoline, dry-cleaning solvents, or other ammable or explosive

substances, as they give off vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any ammable substance,

such as vegetable oil, cooking oil, machine oil, ammable chemicals, paint thinner, etc.,

or anything containing wax or chemicals, such as mops and cleaning cloths. Flammable

substances may cause the fabric to catch re by itself.

4. Do not store or use gasoline or other ammable vapors and liquids near this or any

other appliance.

DV7750M-03170Y-00_EN.indd 5 2016-12-28  11:43:16

Safety information

SAVE THESE INSTRUCTIONS

Safety information

SAVE THESE INSTRUCTIONS

English6

5. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

6. Before the appliance is removed from service or discarded, remove the door to the

drying compartment.

7. Do not reach into the appliance if the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with internal controls.

10. Do not repair or replace any part of the appliance or attempt any service unless

specically recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

11. Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

12. Clean the lint screen before or after each load.

13. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like

materials.

14. Keep area around the exhaust opening and adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

15. The interior of the appliance and exhaust duct should be cleaned periodically by

qualied service personnel.

16. Do not place items exposed to cooking oils in your dryer. Items contaminated with

cooking oils may contribute to a chemical reaction that could cause a load to catch re.

17. This appliance must be grounded. See “Electrical requirements” and “Grounding” in

“Installation” section.

18. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

19. Do not insert your hand under the dryer.

• This may result in injury.

20. Take care that children’s ngers are not caught in the door when closing it.

• This may result in injury.

21. Control board and inlet valve are intentionally not grounded and may present a risk of

electric shock only during servicing.

• Do not contact this part while appliance is energized.

DV7750M-03170Y-00_EN.indd 6 2016-12-28  11:43:16

Safety information

SAVE THESE INSTRUCTIONSSAVE THESE INSTRUCTIONS

English 7

WARNING - To reduce the risk of re or explosion:

• Do not dry items that have been previously cleaned, washed, soaked, or spotted with

gasoline, dry cleaning solvents, or other ammable or explosive substances. They

emit vapors that could ignite or explode. Any material that has been in contact with a

cleaning solvent or ammable liquids or solids should not be placed in the dryer until

all traces of these ammable liquids or solids and their fumes have been removed.

There are many highly ammable items used in homes, such as acetone, denatured

alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,

turpentine, wpees, and wpe removers.

• Items containing foam rubber (may be labeled latex foam) or similarly textured

rubberlike materials must not be dried on a heat setting. Heated foam rubber

materials can, under certain circumstances, produce re by spontaneous combustion.

WARNING - What to do if you smell gas:

• Do not try to light any appliance.

• Do not turn on the appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Clear the room, building or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the re department.

• Installation and service must be performed by a qualied installer, service agency, or

the gas supplier.

DV7750M-03170Y-00_EN.indd 7 2016-12-28  11:43:16

Safety information

SAVE THESE INSTRUCTIONS

Safety information

SAVE THESE INSTRUCTIONS

English8

Warnings

WARNING

• Ensure pockets are free from small, irregularly shaped hard objects, foreign material,

etc. ie. coins, knives, pins, etc. These objects could damage your dryer.

• Gas leaks may occur in your system, resulting in a dangerous situation.

Cautions

CAUTION

• Do not allow children or pets to play on, in, or in front of the appliance. Close

supervision is necessary when the appliance is used near children and pets.

• Before discarding or removing your dryer from service, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

• Do not reach into the appliance when the drum is moving.

• Do not install or store this appliance where it will be exposed to the weather.

• Do not tamper with controls.

• Do not repair, replace, or attempt to service any part of the appliance unless

specically instructed to in the user-repair instructions and you have the

understanding and skills to carry out the procedure.

• Do not use fabric softeners or products to eliminate static unless the softener or

product is recommended for dryer use by the manufacturer of the fabric softener or

product.

• Clean the lint screen before or after each load.

• Keep the area around the exhaust opening and surrounding areas free from lint, dust,

and dirt.

• The interior of the dryer and exhaust duct should be cleaned periodically by qualied

service personnel.

• This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately or not in accordance with local and national codes. See

installation instructions for information about grounding this appliance.

• Do not sit on top of the dryer.

• Do not wash clothing with large buckles, buttons, or other heavy metal or solid objects.

• Gas leaks may not be detected by smell alone.

• Gas suppliers recommend you purchase and install a UL-approved gas detector.

• Install and use in accordance with the manufacturer’s instructions.

DV7750M-03170Y-00_EN.indd 8 2016-12-28  11:43:16

Safety information

SAVE THESE INSTRUCTIONSSAVE THESE INSTRUCTIONS

English 9

• Do not place items in your dryer that have been spotted or soaked with vegetable oil

or cooking oil. Even after being washed, these items may contain signicant amounts

of these oils.

• Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous

combustion increases when items containing vegetable oil or cooking oil are exposed

to heat. Heat sources such as your dryer can warm these items, allowing an oxidation

reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items

can become hot enough to catch re. Piling, stacking, or storing these kinds of items

may prevent heat from escaping and can create a re hazard.

• All washed and unwashed fabrics that contain vegetable oil or cooking oil can be

dangerous.

Washing these items in hot water with extra detergent will reduce, but not eliminate,

the hazard. Always use the Cool Down cycle for these items to reduce their

temperature. Never remove these items from the dryer hot or interrupt the drying

cycle until the items have run through the Cool Down cycle. Never pile or stack these

items when they are hot.

DV7750M-03170Y-00_EN.indd 9 2016-12-28  11:43:16

Installation requirements

English10

Installation requirements

Read through the following instructions before installing the dryer, and keep this manual

for future reference.

WARNING

Control board and inlet valve are intentionally not grounded and may present a risk of

electric shock only during servicing.

Service personnel - Do not contact this part while appliance is energized.

Key installation requirements

• A grounded electrical outlet.

• A power cord for electric dryers (except

in Canada).

• Gas lines (for gas models) that must

meet national and local regulations.

• An exhaust system made of rigid metal

or exible stiff-walled metal exhaust

ducting.

WARNING

Remove the door from all discarded

appliances to prevent a child from

suffocating.

Location considerations

• Adequate clearances between the dryer

and adjacent walls or other surfaces.

• Adequate air circulation for ventilation

and gas combustion.

• Away from water and weather.

WARNING

• Make sure to exhaust the dryer

outdoors to reduce the risk of re.

• Keep the dryer area clear of

combustible materials, gasoline, and

other ammable vapors and liquids.

• Do not install other fuel-burning

appliances around or in the same place

as the dryer.

Alcove or closet installation

Minimum clearances between the dryer

and adjacent walls or other surfaces are:

2” in front, 17” on top, 1” on either side,

and 5” in the back.

The closet front must have two

unobstructed air openings for a combined

minimum total area of 72 in² with 3”

minimum clearance on the top and bottom.

A louvered door with equivalent space

clearance is acceptable.

DV7750M-03170Y-00_EN.indd 10 2016-12-28  11:43:17

Installation requirements

English 11

Ducting requirements

Recommended Use only for short-run installation

Weather hood

type

4” (10.2 cm)

2.5” (6.4 cm)

No. of 90°

elbows

Rigid

Metallic

exible*

Rigid

Metallic

exible*

0 80 ft. (24.4 m) 41 ft. (12.4 m) 74 ft. (22.6 m) 33 ft. (10.1 m)

1 68 ft. (20.7 m) 37 ft. (11.2 m) 62 ft. (18.9 m) 29 ft. (8.8 m)

2 57 ft. (17.4 m) 33 ft. (10.1 m) 51 ft. (15.5 m) 25 ft. (7.6 m)

3 47 ft. (14.3 m) 29 ft. (8.8 m) 41 ft. (12.5 m) 21 ft. (6.5 m)

NOTE

* Use a 4-inch (10.2 cm) diameter rigid aluminum or galvanized steel duct.

If you integrate the dryer’s vent system with an existing exhaust system, make

sure:

• The exhaust system meets all applicable local, state, and national regulations.

• Not to use a exible plastic duct.

• To regularly check and clean all lint buildup from inside the existing ducts.

• The duct is not kinked or crushed.

• The exhaust hood damper opens and closes freely.

Manometer measurements

The static pressure in any exhaust system must not exceed 0.83 inches of water column

or be less than 0. Note that these values are measured with the dryer running with a

manometer presented to the exhaust duct that connects to the dryer. The dryer tumbler

must be empty and lint lter clean.

DV7750M-03170Y-00_EN.indd 11 2016-12-28  11:43:17

Installation requirements

English12

Exhausting requirements

The dryer must not be exhausted into a

chimney, a wall, a ceiling, an attic, a crawl

space, or a concealed space of a building.

Exhausting the dryer to the outside will

prevent large amounts of lint and moisture

from being blown into the room.

In the United States and Canada

• All dryers must be exhausted to the

outside.

• The required exhaust duct is 4 inches

(10.2 cm) in diameter.

• See “Ducting requirements” in the

“Installation” section for the maximum

duct length and number of bends that

can be used.

• The total length of exible metal duct

must not exceed 7’ 10

” (2.4 m).

• Do not assemble the duct with screws

or other fastener means that extend

into the duct and catch lint.

• For the United States only: Use only

those foil-type exible ducts, if any,

specically identied for use with the

appliance by the manufacturer and that

comply with the Outline for Clothes

Dryer Transition Duct. Use Subject

2158A.

Outside the United States and Canada

• Refer to the local codes.

WARNING

• You must exhaust the dryer to the

outside to reduce the risk of re when

you install the dryer in an alcove or

closet.

• Do not use a plastic or non-metal

exible duct.

• If your existing ductwork is plastic, non-

metal, or combustible, replace it with

metal.

• Use only a metal exhaust duct that is

non-ammable to ensure containment

of exhaust air, heat, and lint.

DV7750M-03170Y-00_EN.indd 12 2016-12-28  11:43:17

Installation requirements

English 13

Gas requirements

WARNING

• Use only natural or LP (liquid propane)

gases.

• THE INSTALLATION MUST CONFORM

WITH LOCAL CODES, OR IN THE

ABSENCE OF LOCAL CODES, WITH

THE NATIONAL FUEL GAS CODE ANSI/

Z223.1, LATEST REVISION (FOR THE

UNITED STATES), OR WITH THE CAN /

CGA-B149 INSTALLATION CODES (FOR

CANADA).

• Gas dryers are equipped with a burner

vent for use with natural gas. If you

plan to use your dryer with LP (liquid

propane) gas, it must be converted

for safe and proper performance by a

qualied service technician.

• A

” (1.27 cm) gas supply line is

recommended and must be reduced to

connect to the

” (1 cm) gas line on

your dryer. The National Fuel Gas Code

requires that an accessible, approved

manual gas shut-off valve be installed

within 6” of your dryer.

• Gas dryers installed in residential

garages must be raised 18 inches

(46 cm) above the oor.

• Additionally, a

” (0.3 cm) N.P.T.

(National Pipe Thread) plugged tapping,

accessible for test gauge connection,

must be installed immediately upstream

of your dryer’s gas supply connection.

• Your dryer must be disconnected from

the gas supply pipe system during any

pressure testing of the system.

• Do not reuse old exible metal gas

lines. Flexible gas lines must be

design certied by the American Gas

Association (CGA in Canada).

NOTE

• Your dryer uses an automatic ignition

system to ignite the burner. There is no

constant burning pilot.

• Any pipe joint compound used must be

resistant to the action of any liqueed

petroleum gas.

• As a courtesy, most local gas utilities

will inspect a gas appliance installation.

Commonwealth of Massachusetts

installation instructions

Your dryer must be installed by a licensed

plumber or gas tter. A “T” handle manual

gas valve must be installed in the gas

supply line to your dryer. If a exible gas

connector is used to install your dryer, the

connector can be no longer than 3’ (36”).

WARNING

• Gas leaks may occur in your system,

creating a dangerous situation.

• Gas leaks may not be detected by smell

alone.

• Gas suppliers recommend you purchase

and install a UL-approved gas detector.

• Install and use in accordance with the

manufacturer’s instructions.

DV7750M-03170Y-00_EN.indd 13 2016-12-28  11:43:17

Installation requirements

English14

Electrical requirements

The wiring diagram is located on the plate

under the control panel or rear frame.

WARNING

• Improperly connecting the equipment

grounding conductor can result in a

risk of electric shock. Check with a

qualied electrician or serviceman if

you are in doubt as to whether your

dryer is properly grounded. Do not

modify the plug provided with your

dryer – if it doesn’t t the outlet, have

a proper outlet installed by a qualied

electrician.

• To prevent unnecessary risk of re,

electrical shock, or personal injury, all

wiring and grounding must be done in

accordance with local codes, or in the

absence of local codes, in accordance

with the National Electrical Code, ANSI/

NFPA No. 70-Latest Revision (for the

U.S.) or the Canadian Electrical Code CSA

C22.1 – Latest Revisions and local codes

and ordinances. It is your responsibility

to provide adequate electrical service

for your dryer.

• All gas installations must be done in

accordance with the national Fuel Code

ANSI/Z2231 – Latest Revision (for the

U.S.) or CAN/CGA – B149 Installation

Codes – Latest Revision (for Canada)

and local codes and ordinances.

Grounding

This dryer must be grounded. In the event

of malfunction or breakdown, the ground

will reduce the risk of electrical shock by

providing a path of least resistance for the

electrical current.

Gas models

WARNING

• Your dryer has a cord with an

equipment-grounding conductor and

a grounding plug. The plug must be

plugged into an appropriate outlet that

is properly installed and grounded in

accordance with all local codes and

ordinances.

• Do not modify the plug provided with

your dryer – if it doesn’t’t t the outlet,

have a proper outlet installed by a

qualied electrician.

• Do not connect the ground wire to

plastic plumbing lines, gas lines, or hot

water pipes.

DV7750M-03170Y-00_EN.indd 14 2016-12-28  11:43:17

Installation requirements

English 15

Electric models

WARNING

• Your dryer has an optional cord with

an equipment-grounding conductor

and a grounding plug. This cord is sold

separately.

• The plug must be plugged into an

appropriate outlet that is properly

installed and grounded in accordance

with all local codes and ordinances.

• Do not modify the plug provided with

your dryer – if it doesn’t’t t the outlet,

have a proper outlet installed by a

qualied electrician.

• If a power cord is not used and the

electric dryer is to be permanently

wired, the dryer must be connected to

a permanently grounded metal wiring

system, or an equipment grounding

conductor must be run with the circuit

conductors and connected to the

equipment grounding terminal or lead

on the dryer.

Electrical connections

Before operating or testing, follow all

grounding instructions in the “Grounding”

section. An individual branch (or separate)

circuit serving only your dryer is

recommended.

Do not use an extension cord.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical

service with a 15-ampere fuse or circuit

breaker is required.

Electric models – U.S. only

Most U.S. dryers require a 120 / 240 volt,

60 Hz AC approved electrical service.

Some require 120 / 208 volt, 60 Hz

approved electrical service. The electric

service requirements can be found on

the data label located behind the door.

A 30-ampere fuse or circuit breaker on

both sides of the line is required.

• If a power cord is used, the cord

should be plugged into a 30-ampere

receptacle.

• The power cord is not provided with

U.S. electric model dryers. This cord is

sold separately.

WARNING

Risk of Electric Shock

When local codes allow, you can connect

the dryer’s electrical supply with a new

power supply cord kit, marked for use with

a dryer, that is U.L. listed and rated at a

minimum of 120 / 240 volts, 30-amperes

with three No. 10 copper wire conductors

terminated with closed loop terminals,

open-end spade lugs with turned up ends,

or with tinned leads.

• Do not reuse a power supply cord from

an old dryer. The power cord electric

supply wiring must be supported at the

dryer cabinet by a suitable UL-listed

strain relief.

• Grounding through the neutral

conductor is prohibited for (1) new

branch-circuit installations, (2) mobile

homes, (3) recreational vehicles, and

(4) areas where local codes prohibit

grounding through the neutral

conductor. (Use a 4-prong plug for a

4 wire receptacle, NEMA type 14-30R.)

DV7750M-03170Y-00_EN.indd 15 2016-12-28  11:43:17

Installation requirements

English16

Electric models – Canada Only

• A 120 / 240 volt, 60 Hz AC approved

electrical service fused through a

30-ampere fuse or circuit breaker on

both sides of the line is required.

• All Canadian models are shipped

with the power cord attached. The

power cord should be plugged into a

30-ampere receptacle.

NOTE

In Canada, you may not convert a dryer to

208 volts.

DV7750M-03170Y-00_EN.indd 16 2016-12-28  11:43:17

Installation

English 17

Installation

This dryer must be installed by a qualied technician. The installer is responsible for

connecting the dryer to the main power while observing the relevant safety regulations of

your area.

What’s included

Make sure all the parts are included in the product package. If you have a problem with

the dryer or the accessories, contact a local Samsung customer center or the retailer.

Dryer at a glance

01 Control panel 02 Worktop 03 Filter

04 Door 05 Exhaust duct

DV7750M-03170Y-00_EN.indd 17 2016-12-28  11:43:18

Installation

English18

Accessories & tools

Provided accessories

Y connector Water hose

(Canadian models

only)

Short water hose

Required tools

Pliers Cutting knife Pipe wrench (gas

models only)

Nut driver

Level Philips screwdriver Duct tape Wrench

WARNING

Packing materials can be dangerous to children. Keep all packing materials (plastic bags,

polystyrene, etc.) out of children’s reach.

DV7750M-03170Y-00_EN.indd 18 2016-12-28  11:43:20

Installation

English 19

Step-by-step installation

Make sure you have a qualied technician install the dryer. Step by step installation

instructions start below.

STEP 1 Install the exhaust system

1. Select a location and move the dryer to the site. For easy access, we recommend you

install the dryer in the same location as your washer.

2. To change the door direction, see “Switching the door position”.

3. Install the exhaust system as instructed in the “Exhaust ducting guide” section.

NOTE

• To move the dryer easily, lay two of the carton cushion-from the packaging on the

oor. Tip the dryer on its side so it lies across both cushion-tops. Push the dryer so that

it is near its nal location, and then set the dryer upright.

• Secure room around the dryer to facilitate ducting and wiring.

STEP 2 Connect the gas line

First, read through the “Gas requirements” section, and follow these steps.

1. Remove the protective cap from the gas pipe.

2. Apply a LPG (Liqueed Petroleum Gas)-safe compound or 1.5 wraps of Teon tape to

all threaded connections.

3. Connect the gas supply to the dryer. An additional tting is required to connect the

”

(1.9 cm) female thread end of a exible connector to the

” (1 cm) male threaded end

on the dryer. Tighten up the tting over all threads.

4. Turn on the gas supply, and check for any leaks using a soap solution. If a leak is found,

tighten the connections and try again. DO NOT use an open ame to check for gas

leaks.

DV7750M-03170Y-00_EN.indd 19 2016-12-28  11:43:20

Installation

English20

STEP 3 Connect the electrical wiring

First, read through the “Electrical requirements” section, and follow these steps.

3-wire system

A. External ground connector

B. Neutral grounding wire (white)

C. Center silver-colored terminal block

screw

D. Neutral wire (white or center wire)

” (1.9 cm) UL-listed strain relief

1. Loosen or remove the center terminal

block.

2. Connect the neutral wire (white or

center wire) of the power cable to the

center, silver-colored terminal screw of

the terminal block. Tighten the screws.

3. Connect the other wires to outer

terminal block screws. Tighten the

screws.

4. Tighten the strain relief screws.

5. Insert the terminal block cover into the

rear panel of the dryer. Then, secure the

cover with a hold-down screw.

CAUTION

• To convert from the 4-wire system

to 3-wire system, connect the ground

strap to the terminal block support to

ground the dryer frame to the neutral

conductor.

• Ring-type terminals are recommended.

If using strap terminals, make sure they

are tightened.

DV7750M-03170Y-00_EN.indd 20 2016-12-28  11:43:20

Installation

English 21

4-wire system

A. External ground connector

B. Green or bare copper wire of power

cord

” (1.9 cm) UL-listed strain relief

D. Center silver-colored terminal block

screw

E. Neutral grounding wire (white)

F. Neutral wire (white or center wire)

1. Remove the external ground connector’s

screw, and connect the ground wire

(green or unwrapped) of the power cable

to the screw.

CAUTION

• To connect the ground wire to the

neutral position without through

contact A (cabinet ground), contact

a technician. This is not user

serviceable.

• Ring-type terminals are

recommended. If using strap

terminals, make sure they are

tightened.

2. Loosen or remove the screws from the

center terminal block.

3. Connect the neutral wire (white or

center wire) and ground wire (white) to

the center screw of the terminal block.

Tighten the screw.

4. Connect the other wires to the outer

terminal block screws. Tighten the

screws.

5. Tighten the strain relief screws.

6. Insert the tab of the terminal block cover

into the rear slot of the dryer. Secure the

cover with a hold-down screw.

WARNING

• All U.S. models are designed for a 3-wire system connection. The dryer frame is

grounded to the neutral conductor at the terminal block. A 4-wire system connection

is required for new or remodeled construction, mobile homes, or if local codes do not

permit grounding through neutral. If you use the 4-wire system, you cannot ground the

dryer frame to the neutral conductor at the terminal block.

• Remove the terminal block cover plate. Insert the power cord with a UL-listed strain

relief through the hole provided in the cabinet near the terminal block.

• A strain relief must be used. Do not loosen the nuts already installed on the terminal

block. Be sure they are tight. Use a

” (1 cm) deep well socket.

DV7750M-03170Y-00_EN.indd 21 2016-12-28  11:43:20

Installation

English22

STEP 4 Connect the water hose

The dryer must be connected to a cold water tap using the provided water hoses.

1. Close the cold water tap. If you have a

washer cold water hose attached to the

cold water faucet, unscrew and remove

the hose. Then, connect the female end

of the Y connector to the cold water

tap.

2. Connect the straight end of the water

hose to the Y connector.

3. Using pliers, tighten the coupling an

additional two-thirds turn. Do not

overtighten because the coupling may

be damaged.

4. Connect the angled end of the water

hose to the lling valve at the bottom

of the rear frame. Turn the coupling

manually until it is tight.

5. Using pliers, tighten the coupling an

additional two-thirds turn. Do not

overtighten because the coupling may

be damaged.

6. If you detached the cold water hose

from your washer, attach the hose

to the open end of the Y connector,

tighten the coupling until it is tight,

and then, using a pliers, tighten an

additional two-thirds turn.

7. Open the cold water tap, and then check

for any leaks.

If the Y connector cannot be directly connected to the cold water tap, use the short hose

as shown on the following page.

DV7750M-03170Y-00_EN.indd 22 2016-12-28  11:43:21

Installation

English 23

Using the short hose as an extension

1. Close the cold water tap. If you have

a washer cold water hose attached to

the cold water faucet, unscrew and

remove the hose. Then, connect the

short hose (B) to the cold water tap.

Turn the coupling manually until it is

tight.

2. Using pliers, tighten the coupling an

additional two-thirds turn. Do not

overtighten because the coupling may

be damaged.

3. Connect the Y connector (A) to the brass

male end of the short hose. Turn the

coupling manually until it is tight.

4. Using pliers, tighten the coupling an

additional two-thirds turn. Do not

overtighten because the coupling may

be damaged.

5. Connect the angled end of the water

hoses (C) to the lling valve at the

bottom of the rear frame. Turn the

coupling manually until it is tight.

6. Using pliers, tighten the coupling an

additional two-thirds turn. Do not

overtighten because the coupling may

be damaged.

7. If you detached the cold water hose

from your washer, attach the hose to

the free end of the Y connector, tighten

the coupling until it is tight, and then,

using a pliers, tighten an additional

two-thirds turn.

8. Open the cold water tap, and then check

for any leaks.

DV7750M-03170Y-00_EN.indd 23 2016-12-28  11:43:21

Installation

English24

STEP 5 Level the dryer

To ensure optimal performance, the dryer must be level.

1. Using a level (A), check if the dryer

is level side to side and then front to

back. If the dryer is not level, adjust the

leveling feet (B) at the bottom of the

dryer. Then, check if the dryer is level

again.

A B

NOTE

• To set the dryer to the same height

as your washer, fully retract (A)

the leveling feet by turning them

counterclockwise, then loosen (B) the

feet by turning them clockwise. Once

the dryer is the same height as the

washer, follow the directions above

to level the dryer.

• Adjust the leveling feet only as much

as necessary to level the dryer.

Extending the leveling feet more

than necessary can cause the dryer

to vibrate.

DV7750M-03170Y-00_EN.indd 24 2016-12-28  11:43:21

Installation

English 25

STEP 6 Power on (Gas models)

Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then,

plug the power cord into a power source and check the dryer’s installation and operation

using the nal checklist in Step 7 below.

STEP 7 Final check

When installation is complete, conrm that:

• The dryer is plugged into an electrical outlet and grounded properly.

• The exhaust ductwork is connected and the joints are taped.

• You have used rigid or stiff-walled exible metal duct material, not plastic exible duct.

• The dryer is level and is sitting rmly on the oor.

• The dryer starts, runs, heats, and shuts off properly.

For gas models:

• The gas is supplied properly with no leaks.

CAUTION

The burner may not ignite initially due to air in the gas line. Allowing your dryer to

operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes,

turn your dryer off and wait 5 minutes. Be sure the gas supply to your dryer has been

turned on. To conrm gas ignition, check the exhaust for heat.

Vent blockage test

After the dryer is installed, start the Vent Blockage Test to check if the duct system is

properly installed. The Vent Blockage Test automatically detects the status of the ducts

and reports any blockage or problems. Proper ducting can reduce drying time and save

energy.

NOTE

The Vent Blockage Test must run with the dryer in a cool state. If the dryer warms up

after the installation check, run the AIR FLUFF cycle for several minutes to reduce its

internal temperature.

DV7750M-03170Y-00_EN.indd 25 2016-12-28  11:43:21

Installation

English26

Running the vent blockage test

1. Make sure the drum is empty, and then close the door.

(If there are any clothes or other items in the drum, the test will not give accurate

results.)

2. Press the POWER button to turn the dryer on, then simultaneously press and hold the

Adjust Time

and Dry Level buttons for 3 seconds. “InS or In” appears in the dryer’s

display. (If you have started other procedures before the Vent Blockage Test, the dryer

will not enter the Vent Blockage Test mode.)

3. Press the START/PAUSE button. The Vent Blockage Test starts immediately. During the

test, the number indicator makes a circle in 6 clockwise steps. The test takes about 2

minutes. Do not open the door during the test.

4. After 2 minutes, when the test is complete, the results is displayed and the dryer

sounds a tone.

If status of the duct system is normal, “End or 0” appears and the dryer sounds a

completion tone.

If the duct system can not exhaust properly, “CLg or Cg” appears and the dryer sounds

an alarm tone.

If there are any other problems, an information code appears in the display. For

information about the code, see “Information codes” section on page 43.

• To stop or cancel the Vent Blockage Test, press the POWER button to turn off your

dryer.

• During the test, if “dc” appears in the display, make sure the door is closed. If “C1” is

displayed, see if there is laundry inside drum. If there is, stop the test and remove it.

Then, start the test again.

• The results remain on the display for about 5 minutes and then automatically turn

off. You can turn the result off immediately by pressing the POWER button.

NOTE

• During or after the test, the internal drum is hot. Use caution to prevent burns.

The Vent Blockage Test is used to check for problems to the current duct system when

the dryer is installed for the rst time.

• If the test result displays “CLg or Cg” (the duct system is blocked ), refer to the “Ducting

requirements” section on page 11 and the “Exhaust ducting guide” section below, and

then take proper measures to correct any problems.

If the test is suspended, it could result in incorrect results. Follow the proper

procedures when testing the dryer.

• Even if the test result is normal (“End or 0”), the duct system could be blocked slightly.

Properly install all duct work according to the installation instructions in this manual.

DV7750M-03170Y-00_EN.indd 26 2016-12-28  11:43:21

Installation

English 27

Exhaust ducting guide

Ducting

1. Make sure the dryer is installed properly so the air exhausts freely.

2. Use 4-inch rigid metal ducts. Tape all joints including the dryer connection.

Never use lint-trapping screws.

3. To facilitate the exhaust, keep the ducts as straight as possible.

Cleaning

Clean all old ducts before installing the dryer, and make sure the vent ap opens and

closes freely. We recommend that you to clean the exhaust system annually or on a

regular basis.

WARNING

• To prevent re, do not use plastic, thin-foil, or non-metal exible ducts of any kind.

• Do not use a poor exhaust system because it slows down the dryer’s performance.

• Do not use excessively long ducts that have multiple elbows.

• Do not use crushed or clogged venting or ducts.

Switching the door position

To reverse the direction of the door, we

recommend that you contact a qualied

technician. It is recommended to put a soft

rug on the oor to prevent scratches on

the door.

1. Unplug the power cord of the dryer.

2. Remove the four hinge screws from

the door, and then remove the door by

lifting it up slightly.

DV7750M-03170Y-00_EN.indd 27 2016-12-28  11:43:22

Installation

English28

3. Remove the two screws from the lever

holder, and then remove the holder

cover.

4. Put the lever holder on the other side

as shown, and then tighten the screws.

Install the holder cover on the opposite

side as shown.

5. Use a at-head screwdriver to remove

the two hinge covers from the original

side. Install the hinge covers on the

opposite side as shown.

6. Locate and remove the 10 screws as

shown. Note that screw B (x2) is longer

than the others.

DV7750M-03170Y-00_EN.indd 28 2016-12-28  11:43:22

Installation

English 29

7. Remove the glass holder, and switch

the positions of:

a. the hinge cover and the door handle.

b. the hinge holder and the glass-guide

holder

8. Remove the door lever, and then move

it to the other side as shown.

9. Remove the hole cover (C), and then

insert and tighten the glass holder using

the removed 10 screws.

10. Install the hole cover on the opposite

side as shown.

11. Reinstall the door on the front frame,

and then carefully insert and tighten

the 4 hinge screws.

DV7750M-03170Y-00_EN.indd 29 2016-12-28  11:43:22

Before you start

English30

Before you start

Here are a few things you should know before starting your dryer.

Sort and load

• Put one wash load in the dryer at a

time.

• Do not mix heavy and lightweight items

together.

• To improve drying efciency for one or

two items, add a dry towel to the load.

• For best results, untangle items before

inserting them into the dryer.

• Overloading reduces the tumbling

performance, resulting in uneven

drying and wrinkling.

• Unless recommended on the care label,

do not dry woolens or berglass items.

• Avoid drying unwashed items.

• Do not dry items soiled with oil, alcohol,

gasoline, etc.

Functional prerequisite

Lint lter

To prevent a risk of re, make sure to

clean the lint lter before or after every

load.

1. Turn off the dryer.

2. Open the door, and pull out the lint

lter (A) from inside the tumbler.

3. Remove the lint that has accumulated,

and then clean the lint lter.

4. Reinsert the lint lter, and then close

the door.

CAUTION

• Do not operate the dryer without the

lint lter in place.

• Do not use a damaged or broken lint

lter. This may reduce performance

and/or cause re.

DV7750M-03170Y-00_EN.indd 30 2016-12-28  11:43:22

Operations

English 31

Operations

WARNING

To reduce the risk of re, electric shock, or injury to persons, read the “Safety information“

before operating this appliance.

Feature panel

DVE(G)52M7750*

02 03 04

DVE(G)52M7755*

02 03 04

01 Cycle Selector

Turn the cycle selector to select a desired cycle. When a cycle is

selected, the cycle indicator lights up.

DV7750M-03170Y-00_EN.indd 31 2016-12-28  11:43:23

Operations

English32

02 Dry Level

Press to adjust the dryness in the Sensor Dry and Steam Dry

cycles. The corresponding indicator turns on.

• Larger or bulkier loads may require Very Dry or More Dry for

complete dryness.

• Less Dry is best suited for lightweight fabrics or for leaving

some moisture in the clothing at the end of the cycle.

• Damp Dry is designed to partially dry items. Use for items that

lay at or hang to dry.

NOTE

This option is not available with STEAM SANITIZE, and ACTIVE

WEAR.

03 Temp.

Press to change the temperature of the current cycle.

• High: For sturdy cottons or those labeled Tumble Dry.

• Medium: For permanent press, synthetics, lightweight cottons,

or items labeled Tumble Dry Medium.

• Med Low: For heat lower than Medium. Use to dry synthetic or

washable knit fabrics.

• Low: For heat sensitive items labeled Tumble Dry Low or

Tumble Dry Warm.

• Extra Low: Provides the lowest heated drying temperature

possible.

04 Time

Press to adjust the drying time for the Manual Dry cycles. This

is not available with the Sensor Dry cycles because the dryer

determines the drying time by sensing the current moisture level

of the load.

05 Digital Graphic

Display

Displays all cycle information, including the cycle time,

information code, and operating status.

06 Eco Dry

This function is available with NORMAL and TIME DRY.

With the Eco Dry activated, drying takes a longer time but the

power consumption is reduced.

The drying time can be extended by up to 3 times depending on

the temperature and load. The Eco Dry function is enabled by

default.

DV7750M-03170Y-00_EN.indd 32 2016-12-28  11:43:23

Operations

English 33

07 Mixed Load Bell

The Mixed Load Bell noties you when the average dry level in

a load is damp dry (80 % dried). This lets you take items that you

don’t want fully dried or that dry quickly out of the dryer early

while letting others continue to dry.

You can select this option in all Sensor Dry cycles except for

STEAM SANITIZE, and ACTIVE WEAR. Available dry levels are

Normal Dry, More Dry, and Very Dry.

08 Anti Static

Reduces static electricity that occurs from clothing friction. This is

done by spraying steam in a later stage of the drying cycle.

NOTE

The Anti Static function is only available with NORMAL, HEAVY

DUTY, PERM PRESS, DELICATES, and TIME DRY.

09 Wrinkle Prevent

Wrinkle Prevent provides approximately 180 minutes of

intermittent tumbling in unheated air at the end of the cycle to

reduce wrinkling. Press Wrinkle Prevent to activate this feature.

The load is dry, and can be removed at any time during the

Wrinkle Prevent cycle.

10 My Cycle

Choose your favorite cycle including the cycle time, temperature,

and dry level. See “My Cycle” for details.

11 Adjust Time

You can change the set time in the Manual Dry cycles (TIME DRY,

QUICK DRY, or AIR FLUFF) and WRINKLE AWAY. To change the

cycle time, press

or until the desired time is displayed.

12 Sound

Press Sound to turn on or off the dryer’s notication beeps and

melodies.

NOTE

This function remains active even after you restart the dryer.

13 POWER Press to turn on/turn off the dryer.

14 START/PAUSE Press to start or stop operation.

NOTE

Extremely tangled items nished by the washer may degrade the drying efciency or

cause the door to open. We recommend that you untangle the items before drying.

DV7750M-03170Y-00_EN.indd 33 2016-12-28  11:43:23

Operations

English34

Simple steps to start

1. Press POWER to turn on the dryer.

2. Turn the Cycle Selector to select a cycle.

3. Change the cycle settings (Dry Level

and Time) as necessary.

4. Optionally, you can activate options

available by pressing the relevant

button (Mixed Load Bell, Anti Static,

Wrinkle Prevent, and/or Eco Dry).

5. Press START/PAUSE. The dryer indicator

turns on with an estimated cycle time

on the display.

To change the cycle during operation

1. Press START/PAUSE to stop operation.

2. Select a different cycle.

3. Press START/PAUSE again to start the

new cycle.

DV7750M-03170Y-00_EN.indd 34 2016-12-28  11:43:23

Operations

English 35

Cycle overview

Sensor Dry

Sensor Dry cycles sense moisture in the load and stop the dryer when the load reaches

the dryness level you have selected with Dry Level.

Cycle Description

NORMAL

For most fabrics including cottons and linens.

If NORMAL is selected, the Eco Dry function is enabled by default.

For more information, see Eco Dry in the “Feature panel“ section.

HEAVY DUTY

For drying items made out of heavy fabrics, such as jeans,

corduroys, or work clothes, with high temperature heat.

BEDDING For bulky items such as blankets, sheets, and comforters.

PERM PRESS

Dry wrinkle-free cottons, synthetic fabrics, knits, and permanent

press fabrics automatically.

DELICATES For heat-sensitive items at a low drying temperature.

TOWELS For bath towels and similar items

ACTIVE WEAR

For exercise wear and outdoor wear such as sports jerseys,

training pants, water-repellent jackets, and other performance

clothing.

Thick fabrics like a zipper or velcro closure of a jacket, or training

socks may not be completely dried.

Manual Dry

You can change the drying settings manually to your preference.

Cycle Description

TIME DRY

You can specify a cycle time in minutes.

If TIME DRY is selected, the Eco Dry function is enabled by

default. For more information, see Eco Dry in the “Feature panel“

section.

QUICK DRY A quick drying cycle running for 30 minutes

AIR FLUFF Tumbles the load in room temperature air.

DV7750M-03170Y-00_EN.indd 35 2016-12-28  11:43:23

Operations

English36

Steam Dry

Use steam to reduce wrinkling and odors on items.

Cycle Description

REFRESH

Use to smooth out wrinkles and reduce odors in loads of one to

four items. With this cycle selected, a small amount of water is

sprayed into the dryer drum after several minutes of tumbling

with heat. Conrm that the laundry load is dry.

WRINKLE AWAY

For best results, load 2-3 items at once. You can extend the

drying time by a minimum of 20 minutes, depending on the item

type or load. Conrm that the laundry load is dry.

STEAM SANITIZE

Use to sanitize items by applying steam and high-temperature

heat to the fabric. This cycle can make items soft and reduce

smells. Conrm that the laundry load is wet or partially wet.

Cycle guide

The best way to dry items is to follow the instructions on the care label. If no drying

instructions are provided, see the following table for reference.

Item Description

Bedspreads &

Comforters

Follow the care label instructions or dry using BEDDING.

• Make sure the item is thoroughly dry before using or storing.

• May require repositioning in the drum to ensure even drying.

Blankets

Use NORMAL and dry only one blanket at a time for best

tumbling action.

• Make sure blankets are is thoroughly dry before using or

storing.

Curtains & Draperies

Use PERM PRESS and the Medium temperature setting to help

minimize wrinkling.

• Dry curtains and draperies in small loads for best results and

remove as soon as possible.

Cloth Diapers

Use NORMAL and the medium temperature setting for soft, uffy

diapers.

Down–lled Items

(jackets, sleeping

bags, comforters,

etc.)

Use NORMAL and the Medium temperature setting.

• Add a couple of dry towels to absorb moisture and shorten

drying time.

DV7750M-03170Y-00_EN.indd 36 2016-12-28  11:43:23

Operations

English 37

Item Description

Foam Rubber (rug

backs, stuffed toys,

shoulder pads, etc.)

Do not dry on a heat setting. Use AIR FLUFF.

WARNING

Drying a rubber item with heat may damage it or cause a re.

Pillows

Use NORMAL.

• Add a couple of dry towels and a pair of clean sneakers to help

the tumbling action and to uff the items.

• Do not dry kapok or foam pillows using a heated drying cycle.

You can dry these items in the dryer only if you use AIR FLUFF.

Plastics (shower

curtains, outdoor

furniture covers, etc.)

Use AIR FLUFF or TIME DRY and the Low or Extra Low

temperature settings depending on the care label instructions.

WARNING

Do not dry:

• Fiberglass items (curtains, draperies, etc.)

• Woolens, unless recommended on the label

• Items spotted or soaked with vegetable or cooking oils

Special features

Child Lock

Child Lock prevents children from

playing with the dryer. When Child Lock

is activated, all buttons except for the

POWER button are disabled.

To activate/deactivate Child Lock,

simultaneously press and hold Dry Level.

and Temp. for 3 seconds.

NOTE

Once Child Lock is activated, it will remain

active even after you restart the dryer.

If other buttons, except for the POWER

button, do not respond, check the Child

Lock indicator. If the indicator is on, follow

the instructions above to turn Child Lock

off.

Drum Light

To turn on the drum light while the

dryer is running, press and hold Time for

3 seconds.

NOTE

After 5 minutes of inactivity, the drum

light automatically turns off.

DV7750M-03170Y-00_EN.indd 37 2016-12-28  11:43:24

Operations

English38

Sound On/Off

To turn off the dryer’s notication

beeps and melodies, press and hold

Sound button.

To unmute the dryer, press and hold

Sound button.

NOTE

This function remains active even after

you restart the dryer.

My Cycle

You can create your own cycle that

contains your preferred settings, and use it

at your convenience.

1. Turn the Cycle Selector to select a cycle.

The cycle indicator turns on.

2. Set or change the settings (Dry Level,

Temp., Time, etc) and/or options as

necessary. Each corresponding indicator

blinks.

3. Press and hold My Cycle for 3 seconds.

The dryer stores the selected cycle with

its settings.

To use My Cycle, press and hold My Cycle

for 3 seconds.

Smart Care

If the dryer displays an information

code, you can use Smart Care to check

the status of the dryer on a smartphone.

To use Smart Care, you must have the

Samsung Smart Care app installed on your

smartphone.

NOTE

Smart Care is optimized for Samsung

Galaxy and Apple iPhones. (Not compatible

with some models).

Download the Samsung Smart Care app

from the Google Play Store or Apple App

store (Search word: “Samsung Smart

Washer/Dryer”), and install it on your

smartphone.

If an information code appears on the

dryer, follow these steps:

1. Press and hold Sound for 3 seconds to

activate Smart Care. The Smart Care

indicator turns on.

2. Open the Smart Care app on your

smartphone.

3. Put the smartphone’s camera close

to the display of the dryer. The

app automatically recognizes the

information code, and displays

suggestions on your smartphone.

4. If the smartphone fails to recognize the

information code more than twice, type

the information code manually into the

Smart Care app.

CAUTION

• If light is reected on the display of

the dryer, the smartphone may not

recognize the information code.

• If you hold the smartphone at an angle

to the dryer’s display, the dryer may

not recognize the information code.

For best results, hold the smartphone

so that the front of the panel and the

smartphone are parallel or nearly

parallel.

• After you use this function, the dryer

will delete delete the record of the

information code from its code log.

DV7750M-03170Y-00_EN.indd 38 2016-12-28  11:43:24

Maintenance

English 39

Maintenance

Keep the dryer clean to prevent decreased performance and to lengthen its life cycle.

WARNING

The control board and inlet valve are intentionally not grounded and may present a risk of

electric shock only during servicing.

Service personnel - Do not contact this part while the dryer is energized.

Vent sensor (applicable models only)

The dryer features a vent sensor that detects and noties you when it is time to clean the

ductwork. The indicator lets you know the status of the duct.

Level

Indicator

Status Action

0 Off The ductwork is not clogged.

1 On

• The duct or lint lter is

clogged.

• The pressure applied to

the duct is high because

the duct is too long or

bent.

• Check the lint lter or duct

and clean if necessary.

• Check the duct connections

and shorten or straighten

the duct if necessary.

2 Blinking

• The duct or lint lter is

severely clogged.

• The pressure applied

to the duct is very high

because the duct is too

long or bent.

• Check and clean the lint

lter or duct and make

sure they are not clogged.

• Check the duct connections

and shorten or straighten

the duct work.

If the dryer is in the Level 2 state, the

indicator blinks for 3 hours after the completion

of the current cycle. If you press POWER or open the door, the dryer powers off

immediately.

NOTE

• For duct installation, see “Exhaust ducting guide”.

• The dryer may keep running even if the duct is clogged, but the drying time will be

extended.

• If the indicator turns on for the rst time and is solid (not blinking), check and clean the

lint lter and/or duct.

• If the indicator turns on again later, it is because the duct is installed or connected with

some restrictions (it’s too long or has too many bends). This is not a system failure.

However, drying time may be extended or the drying performance may be degraded.

DV7750M-03170Y-00_EN.indd 39 2016-12-28  11:43:24

Maintenance

English40

Cleaning

Feature panel

• Clean with a soft, damp cloth. Do not

use abrasive substances.

• Do not spray liquid cleaning agents

directly on the display of the dryer.

• Some laundry pre-treatment soil and

stain removers may damage the feature

panel.

• When using liquid cleaning agents,

apply them to the cleaning cloth. Do not

apply them directly to the dryer. Wipe

up any spills or overspray immediately.

Tumbler

• Remove any stains from the tumbler

with an all-purpose cleaner.

• Tumble old towels or rags to remove

any remaining stains or cleaning

substances. Stains may be still visible,

but will not affect subsequent loads.

Powder coat tumbler

To clean the powder coat tumbler, use

a damp cloth with a mild, non-abrasive

cleaner suitable for easily marred surfaces.

Remove cleaner residue and dry with a

clean cloth.

Dryer exterior

• Clean with a soft, damp cloth. Do not

use abrasive substances.

• Protect the surface from sharp objects.

• Do not place any heavy or sharp

objects or a detergent container on the

dryer. They can scratch or damage the

top cover of the dryer.

• The dryer has a high-gloss nish on the

entire surface. Be careful not to scratch

or damage the surface.

Exhaust system

• Check and clean the exhaust system on

a yearly or regular basis to maintain

optimum performance.

• The external exhaust hood must be

cleaned more frequently to ensure a

proper air ow.

DV7750M-03170Y-00_EN.indd 40 2016-12-28  11:43:24

Troubleshooting

English 41

Troubleshooting

Checkpoints

If the dryer operates abnormally, rst check the list of problems in the table below and

try the suggested actions.

Problem Action

Does not run.

• Make sure the door is latched shut.

• Make sure the power cord is plugged into a live electrical

outlet.

• Check your home’s circuit breakers or fuses.

• Press or tap START/PAUSE again if the door is opened during

a cycle.

• Clean the lint lter.

Does not heat.

• Check your home’s circuit breakers or fuses.

• Some cycles do not require heating. Check the selected cycle

again.

• For a gas dryer, make sure the gas supply is on.

• Clean the lint lter and exhaust duct.

• The dryer may have moved into the cool-down phase of the

cycle.

Does not dry.

• Check all of the above, plus...

• Make sure the exhaust hood outside your home can open and

close freely.

• Check the exhaust system for lint buildup. Ducting should be

inspected and cleaned annually.

• Use a 4” rigid metal exhaust duct.

• Do not overload. 1 wash load = 1 dryer load.

• Dry heavy items and light weight items separately.

• Large, bulky items, such as blankets or comforters, may

require repositioning to ensure even drying.

• Make sure that your washer is draining properly and

extracting adequate water from the load.

• The load may be too small to tumble properly. Add a few

towels and restart the dryer.

• The load may be too large to tumble properly. Remove some

items and restart the dryer.

• Clean the lint lter.

DV7750M-03170Y-00_EN.indd 41 2016-12-28  11:43:24

Troubleshooting

English42

Problem Action

Is noisy.

• Check the load for objects such as coins, loose buttons, nails,

etc. Remove promptly.

• It is normal to hear the dryer gas valve or heating element

cycle on and off during the drying cycle.

• Make sure the dryer is leveled properly as outlined in the

installation instructions.

• It is normal for the dryer to hum due to the high velocity of

air moving through the dryer drum, fan, or exhaust system.

Dries unevenly.

• Seams, pockets, and other similarly heavy areas may not

be completely dry when the rest of the load has reached

the selected dryness level. This is normal. You can choose

a higher dryness level or a cycle that involves a higher

dryness level.

• If one heavy item is dried with a light weight load, such as

one towel with sheets, it is possible that the heavy item will

not be completely dry when the rest of the load has reached

the selected dryness level.

• For the best drying results, dry heavy items and light weight

items separately.

Has odors.

• Household odors from paint, varnish, strong cleaners, etc.

may enter the dryer with the surrounding room air. This is

normal as the dryer draws the air from the room, heats it,

pulls it through the tumbler, and exhausts it outside.

• When these odors linger in the air, completely ventilate the

room before using the dryer.

• Use a cycle featuring the Refresh function. If odors persist,

wash and dry the item again.

Lint on clothes.

• Make sure the lint lter is cleaned before every load. For

clothes that naturally build up lint, clean the lter during the

cycle.

• Some fabrics are lint producers (for example, a fuzzy white

cotton towel) and they must be dried separately from clothes

that are lint trappers (for example, a pair of black linen

pants).

• Divide larger loads into smaller loads for drying.

• Check pockets thoroughly before drying, then dry clothes.

• Remove lint inside the drum before drying.

DV7750M-03170Y-00_EN.indd 42 2016-12-28  11:43:24

Troubleshooting

English 43

Problem Action

Items still wrinkled

after WRINKLE

PREVENT

(WRINKLE-CARE,

WRINKLE RELEASE).

• Small loads of 1 to 4 items work best.

• Load fewer items. Load similar-type items.

• Take out the items immediately after drying is complete.

Water drips from the

nozzle when STEAM

CARE starts.

• This is steam condensation. The dripping water will stop after

a short time.

Sprayed water is not

visible during STEAM

CARE.

• Sprayed water is difcult to see when the door is closed.

Extended time.

• Sensor Dry automatically senses the moisture in the load

and shuts the dryer off when the selected dryness level is

reached.

The drying time can change according to the type and

amount of laundry. See the cycle chart for reference.

If a problem persists, contact a local Samsung service center.

Information codes

If the dryer fails to operate, you may see an information code on the display panel.

To determine what you should do, check the list codes in the table below and try the

suggested actions.

Code Action

Operating the dryer with the door open.

• Make sure the door is properly closed.

• Make sure laundry is not caught in the door.

Invalid power source frequency

• Try restarting the cycle.

• If this information code remains, contact a Samsung customer

service center.

Electronic control problem (Invalid Communication).

• Contact a Samsung a customer service center.

DV7750M-03170Y-00_EN.indd 43 2016-12-28  11:43:24

Troubleshooting

English44

Code Action

Malfunction is detected in the motor relay circuit.

• Contact a Samsung customer service center.

High temperature heating check

• Clean the lint lter.

• If this information code remains, contact a Samsung customer

service center.(enter the line test mode)

HC4

9C1

The electronic control needs to be checked.

• Check if power is supplied properly.

• If the information code remains, contact a customer service

center.

The Thermistor1 resistance is very low or high.

• Check for a clogged lint screen

• Check if the vent system is restricted.

• If this information code remains, contact a Samsung customer

service center.

tC5

The Thermistor2 resistance is very low or high.

• Check for a clogged lint screen.

• Check if the vent system is restricted.

• If this information code remains, contact a Samsung customer

service center.

Incorrect door switch.

• Contact a Samsung customer service center.

If any information code keeps appearing on the screen, contact a local Samsung service

center.

DV7750M-03170Y-00_EN.indd 44 2016-12-28  11:43:24

Specications

English 45

Specications

Fabric care chart

The following symbols provide garment

care direction. The clothing care labels

include symbols for drying, bleaching,

drying and ironing, or dry cleaning when

necessary. The use of symbols ensures

consistency among garment manufacturers

of domestic and imported items. Follow

care label directions to optimize garment

life and reduce laundering problems.

Wash cycle

Normal

Permanent press/Wrinkle

resistant/Wrinkle control

Gentle/Delicates

Hand wash

Water temperature

Hot

Warm

Cold

NOTE

This represents appropriate wash water

temperatures for various items. The

temperature range for Hot is 41-52 °C,

for Warm 29-41 °C and for Cold 16-29 °C.

(Wash water temperature must be a

minimum of 16 °C for detergent activation

and eff ective cleaning.)

Bleach

Any bleach (when needed)

Only non-chlorine (color-safe)

bleach (when needed)

Tumble dry

Normal

Permanent press/Wrinkle

resistant/Wrinkle control

Gentle/Delicates

Special instructions

Line dry/Hang to dry

Drip dry

Dry at

Heat setting

High

Medium

Low

Any heat

No heat / Air

DV7750M-03170Y-00_EN.indd 45 2016-12-28  11:43:26

Specications

English46

Iron dry or steam temperatures

High

Medium

Low

Warning symbols for laundering

Do not wash

Do not wring

Do not bleach

Do not tumble dry

No steam (added to iron)

Do not iron

Dry-clean

Do not dry-clean

Line dry / Hang to dry

Drip dry

Dry at

Protecting the environment

This appliance is manufactured from

recyclable materials. If you decide to

dispose of this appliance, please observe

local waste disposal regulations. Cut off

the power cord so that the appliance

cannot be connected to a power source.

Remove the door so that animals and small

children cannot get trapped inside the

appliance.

DV7750M-03170Y-00_EN.indd 46 2016-12-28  11:43:27

Specications

English 47

Specication sheet

NOTE

“A. Height” Spec can vary from 46 to

46.5 inches (116.8-118.0 cm) depending

on the leveling feet adjustment.

Type Front loading dryer

Model name DVE(G)52M775**

Dimensions

A. Height

Product - inches (cm) 46.0 (116.8)

Required for Installation - inches 48.0

B. Width

Product - inches (cm) 27.0 (68.6)

Required for Installation - inches 29.0

C. Depth

Product - inches (cm) 30.0 (76.3)

Required for Installation - inches 35.0

D. Depth with

door open 90°

Product - inches (cm) 49.80 (126.5)

Required for Installation - inches 54.82

E. Width with

door open 130°

Product - inches (cm) 46.47 (118.0)

Required for Installation - inches 51.47

Water pressure - psi (kPa) 20-116 (137-800)

NET weight

Electric - lb (kg) 127.9 (58)

Gas - lb (kg) 130.1 (59)

Heater rating

Electric (W) 5300

Gas (BTU/hr) 22000

DV7750M-03170Y-00_EN.indd 47 2016-12-28  11:43:28

Specications

English48

Cycle chart

NOTE

For best results, follow the load size recommendations for each dry cycle.

•

Large load: Fill the drum to about

full. Do not add items over this level as they

need to tumble freely.

•

Medium load : Fill the drum to about

full.

•

Small load : Fill the drum with 3-5 items, not more than ¼ full.

Cycle Recommended items

Load

size

Dry Level

Sensor Dry

NORMAL

Cottons, work clothes, linens, mixed

loads

Normal Dry

(Adjustable)

HEAVY DUTY

Heavy Fabrics such as jeans,

corduroys, heavy work clothes

Normal Dry

(Adjustable)

BEDDING

Bulky items such as blankets, sheets,

comforters, pillows

Normal Dry

(Adjustable)

PERM PRESS

Shirts, synthetic fabrics, knits,

wrinkle-free cottons, permanent press

Normal Dry

(Adjustable)

DELICATES Underwear, blouses, lingerie

Normal Dry

(Adjustable)

TOWELS Bath towels and similar items

Normal Dry

(Adjustable)

ACTIVE WEAR

Water-repellent wear, performance

clothes, sports wear (Maximum: 4 lbs)

Normal Dry

(No change)

Manual Dry

TIME DRY Any load

QUICK DRY Small loads

AIR FLUFF Foam, rubber, plastic

Steam Dry

REFRESH Shirts, trousers, comforters, pillows

WRINKLE AWAY Shirts, trouser, blouses

STEAM SANITIZE Bedding, curtains, children’s clothing

Very Dry

(No change)

DV7750M-03170Y-00_EN.indd 48 2016-12-28  11:43:28

Specications

English 49

NOTE

• : factory setting, : can be selected

Cycle

Temperature setting

Time

setting

High Medium Med Low Low

Extra

Low

Sensor Dry

NORMAL



HEAVY DUTY



BEDDING



PERM PRESS



DELICATES



TOWELS



ACTIVE WEAR



Manual Dry

TIME DRY

     

QUICK DRY

 

AIR FLUFF



Steam Dry

REFRESH



WRINKLE AWAY

 

STEAM SANITIZE



Cycle

Options

Eco Dry

Mixed Load

Bell

Anti Static

Wrinkle

Prevent

Adjust Time

Sensor Dry

NORMAL

   

HEAVY DUTY

  

BEDDING

 

PERM PRESS

  

DELICATES

  

TOWELS

 

ACTIVE WEAR



Manual Dry

TIME DRY

   

QUICK DRY

 

AIR FLUFF

 

Steam Dry

REFRESH



WRINKLE AWAY

 

STEAM SANITIZE



DV7750M-03170Y-00_EN.indd 49 2016-12-28  11:43:28

English50

Warranty (U.S.A)

SAMSUNG DRYER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS

AMERICA, INC. (SAMSUNG) and delivered new, in the original carton to the original

consumer purchaser, is warranted by SAMSUNG against manufacturing defects in

materials and workmanship for a limited warranty period of:

• One (1) Year All Parts and Labor

This limited warranty begins on the original date of purchase, and is valid only on

products purchased and used in the United States.

To receive warranty service, the purchaser must contact SAMSUNG for problem

determination and service procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to

SAMSUNG or SAMSUNG’s authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject

to availability within the contiguous United States.

In-home service is not available in all areas.

To receive in-home service, product must be unobstructed and accessible to the service

agent.

If service is not available, SAMSUNG may elect to provide transportation of the product to

and from an authorized service center.

SAMSUNG will repair, replace, or refund this product at our option and at no charge as

stipulated herein, with new or reconditioned parts or products if found to be defective

during the limited warranty period specied above.

All replaced parts and products become the property of SAMSUNG and must be returned

to SAMSUNG.

Replacement parts and products assume the remaining original warranty, or ninety (90)

days, whichever is longer.

DV7750M-03170Y-00_EN.indd 50 2016-12-28  11:43:28

English 51

This limited warranty covers manufacturing defects in materials and workmanship

encountered in normal, noncommercial use of this product and shall not apply to the

following: damage that occurs in shipment; delivery and installation; applications and

uses for which this product was not intended; altered product or serial numbers; cosmetic

damage or exterior nish; accidents, abuse, neglect, re, water, lightning, or other acts

of nature or God; use of products, equipment, systems, utilities, services, parts, supplies,

accessories, applications, installations, repairs, external wiring or connectors not supplied

or authorized by SAMSUNG that damage this product or result in service problems;

incorrect electrical line voltage, uctuations and surges; customer adjustments and

failure to follow operating instructions, maintenance and environmental instructions that

are covered and prescribed in the instruction book; product removal and reinstallation;

problems caused by pest infestations.

This limited warranty does not cover problems resulting from incorrect electric current,

voltage or supply, light bulbs, house fuses, house wiring, cost of a service call for

instructions, or xing installation errors.

SAMSUNG does not warrant uninterrupted or error-free operation of the product.

EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER

EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT

NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR

FITNESS FOR A PARTICULAR PURPOSE.

NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH

RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.

SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO

REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE, OR INABILITY TO USE THIS

PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND

EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN

THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED

DAMAGE.

WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY

FOR LOSS, DAMAGE, OR INJURY TO PURCHASER AND PURCHASER’S PROPERTY AND TO

OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE, OR INABILITY TO USE

THIS PRODUCT.

THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL

PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE

REMEDY.

DV7750M-03170Y-00_EN.indd 51 2016-12-28  11:43:28

Warranty (U.S.A)

English52

Some states do not allow limitations on how long an implied warranty lasts, or the

exclusion or limitation of incidental or consequential damages, so the above limitations

or exclusions may not apply to you. This warranty gives you specic rights, and you may

also have other rights, which vary from state to state.

To obtain warranty service, please contact SAMSUNG at:

Samsung Electronics America, Inc.

85 Challenger Road

Ridgeeld Park, NJ 07660

1-800-SAMSUNG (726-7864)

www.samsung.com/us/support

Visits by a Service Engineer to explain functions, maintenance or installation is not

covered by warranty.

Please contact your Samsung call agent for help with any of these issues.

DV7750M-03170Y-00_EN.indd 52 2016-12-28  11:43:28

English 53

Warranty (CANADA)

SAMSUNG DRYER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS

CANADA, INC. (SAMSUNG) and delivered new, in the original carton to the original

consumer purchaser, is warranted by SAMSUNG against manufacturing defects in

materials and workmanship for a limited warranty period of:

• One (1) year part and labor

This limited warranty begins on the original date of purchase, and is valid only on

products purchased and used in the Canada.

To receive warranty service, the purchaser must contact SAMSUNG for problem

determination and service procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to

SAMSUNG or SAMSUNG’s authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject

to availability within the Canada.

In-home service is not available in all areas.

To receive in-home service, product must be unobstructed and accessible to the service

agent.

If service is not available, SAMSUNG may elect to provide transportation of the product to

and from an authorized service center.

SAMSUNG will repair, replace, or refund this product at our option and at no charge as

stipulated herein, with new or reconditioned parts or products if found to be defective

during the limited warranty period specied above.

All replaced parts and products become the property of SAMSUNG and must be returned

to SAMSUNG.

Replacement parts and products assume the remaining original warranty, or ninety (90)

days, whichever is longer.

DV7750M-03170Y-00_EN.indd 53 2016-12-28  11:43:28

Warranty (CANADA)

English54