Yamaha CLP-153SG El manual del propietario

Marca: Yamaha

Modelo: CLP-153SG

Categoría: Sintetizador

Tipo: El manual del propietario

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

92-469 1

ENVIRONMENTAL ISSUES: Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is ap-

proximately five years. When replacement becomes nec-

essary, contact a qualified service representative to per-

form the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the

manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and con-

sult your dealer before requesting service.

NAME PLATE LOCATION: The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these graph-

ics appears on this page. Please observe all cautions indi-

cated on this page and those indicated in the safety in-

struction section.

See bottom of Keyboard enclosure for graphic symbol markings

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing) in-

structions in the literature accompany-

ing the product.

The lightning flash with arrowhead

symbol, within the equilateral triangle,

is intended to alert the user to the pres-

ence of uninsulated “dangerous volt-

age” within the product’s enclosure that

may be of sufficient magnitude to con-

stitute a risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic prod-

ucts are tested and approved by an independent safety

testing laboratory in order that you may be sure that when

it is properly installed and used in its normal and custom-

ary manner, all foreseeable risks have been eliminated.

DO NOT modify this unit or commission others to do so

unless specifically authorized by Yamaha. Product per-

formance and/or safety standards may be diminished.

Claims filed under the expressed warranty may be denied

if the unit is/has been modified. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the specifications

without notice or obligation to update existing units.

Model _____________________________________

Serial No. __________________________________

Purchase Date ______________________________

SPECIAL MESSAGE SECTION

WARNING- When using any electrical or electronic prod-

uct, basic precautions should always be followed. These pre-

cautions include, but are not limited to, the following:

1. Read all Safety Instructions, Installation Instructions,

Special Message Section items, and any Assembly Instructions

found in this manual BEFORE marking any connections, in-

cluding connection to the main supply.

2. Main Power Supply Verification: Yamaha products are

manufactured specifically for the supply voltage in the area

where they are to be sold. If you should move, or if any doubt

exists about the supply voltage in your area, please contact

your dealer for supply voltage verification and (if applicable)

instructions. The required supply voltage is printed on the

name plate. For name plate location, please refer to the graphic

found in the Special Message Section of this manual.

3. This product may be equipped with a polarized plug

(one blade wider than the other). If you are unable to insert the

plug into the outlet, turn the plug over and try again. If the

problem persists, contact an electrician to have the obsolete

outlet replaced. Do NOT defeat the safety purpose of the plug.

4. Some electronic products utilize external power sup-

plies or adapters. Do NOT connect this type of product to any

power supply or adapter other than one described in the owners

manual, on the name plate, or specifically recommended by

Yamaha.

5. WARNING: Do not place this product or any other

objects on the power cord or place it in a position where any-

one could walk on, trip over, or roll anything over power or

connecting cords of any kind. The use of an extension cord is

not recommended! If you must use an extension cord, the

minimum wire size for a 25' cord (or less) is 18 AWG. NOTE:

The smaller the AWG number, the larger the current handling

capacity. For longer extension cords, consult a local electri-

cian.

6. Ventilation: Electronic products, unless specifically

designed for enclosed installations, should be placed in loca-

tions that do not interfere with proper ventilation. If instruc-

tions for enclosed installations are not provided, it must be

assumed that unobstructed ventilation is required.

7. Temperature considerations: Electronic products

should be installed in locations that do not significantly con-

tribute to their operating temperature. Placement of this prod-

uct close to heat sources such as; radiators, heat registers and

other devices that produce heat should be avoided.

8. This product was NOT designed for use in wet/damp loca-

tions and should not be used near water or exposed to rain. Exam-

ples of wet/damp locations are; near a swimming pool, spa, tub,

sink, or wet basement.

9. This product should be used only with the components

supplied or; a cart, rack, or stand that is recommended by the

manufacturer. If a cart, rack, or stand is used, please observe all

safety markings and instructions that accompany the accessory

product.

10. The power supply cord (plug) should be disconnected from

the outlet when electronic products are to be left unused for ex-

tended periods of time. Cords should also be disconnected when

there is a high probability of lightening and/or electrical storm

activity.

11. Care should be taken that objects do not fall and liquids are

not spilled into the enclosure through any openings that may exist.

12. Electrical/electronic products should be serviced by a

qualified service person when:

a. The power supply cord has been damaged; or

b. Objects have fallen, been inserted, or liquids have been

spilled into the enclosure through openings; or

c. The product has been exposed to rain: or

d. The product dose not operate, exhibits a marked change

in performance; or

e. The product has been dropped, or the enclosure of the

product has been damaged.

13. Do not attempt to service this product beyond that de-

scribed in the user-maintenance instructions. All other servicing

should be referred to qualified service personnel.

14. This product, either alone or in combination with an ampli-

fier and headphones or speaker/s, may be capable of producing

sound levels that could cause permanent hearing loss. DO NOT

operate for a long period of time at a high volume level or at a

level that is uncomfortable. If you experience any hearing loss or

ringing in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

15. Some Yamaha products may have benches and/or acces-

sory mounting fixtures that are either supplied as a part of the

product or as optional accessories. Some of these items are de-

signed to be dealer assembled or installed Please make sure that

benches are stable and any optional fixtures (where applicable) are

well secured BEFORE using. Benches supplied by Yamaha are

designed for seating only. No other uses are recommended.

INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,

AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.

IMPORTANT SAFETY INSTRUCTIONS

PLEASE KEEP THIS MANUAL

92-469-2

vii

Introduction

Thank you for choosing a Yamaha CLP-153SG Clavinova. Your Clavinova is a fine musical

instrument that employs advanced Yamaha music technology. With the proper care, your

Clavinova will give you many years of musical pleasure.

● Yamaha’s AWM (Advanced Wave Memory) tone generator system offers rich, realistic voices.

● Piano-like touch response — adjustable in 4 stages — provides extensive expressive control and out-

standing playability.

● Dual play mode allows 2 voices to be played simultaneously.

● Unique Clavinova Tone voice provides a fresh sound for new musical expression.

● Damper pedal includes natural resonance effect for the piano voice, simulates the string and sound-

board resonance of acoustic pianos.

● Metronome feature with variable tempo facilitates practice.

● Record and play back anything you play on the keyboard (up to approximately 4,200 notes).

● MIDI compatibility and a range of MIDI functions make the Clavinova useful in a range of advanced

MIDI music systems.

In order to make the most of your Clavinova’s performance potential and features, we urge you

to read this Owner’s Manual thoroughly, and keep it in a safe place for later reference.

Your Clavinova is a fine musical instrument, and deserves the most careful treatment.

Observe the following points and your Clavinova will sound and look great for many years.

1 Never open the case and touch or tamper with the inter-

nal circuitry.

2 Always turn the POWER switch OFF after use, and

cover the keyboard with the dust cover provided.

3 Clean the cabinet and keys of your Clavinova only with

a clean, slightly damp cloth. A neutral cleanser may be

used if desired. Never use abrasive cleansers, waxes,

solvents or chemical dust cloths since these can dull or

damage the finish.

4 Never place any vinyl products on your Clavinova. Con-

tact with vinyl can cause irreversible damage to the

finish.

5 Install your Clavinova in a place that is away from di-

rect sunlight, excessive humidity or heat.

6 Never apply excessive force to the controls, connectors

or other parts of your Clavinova, and avoid scratching

or bumping it with hard objects.

● Name Plate Location

The CLP-153SG name plate is located on the bottom

panel.

Taking Care Of Your Clavinova

Manual de instrucciones

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Español

English

Deutsch

Français

Contents

The Control Panel .................................................. 2

Connections ............................................................ 4

Selecting & Playing Voices.................................. 5

■ Playing the Demonstration Tunes...................... 5

The Dual Mode ........................................................ 6

● Adjusting the Balance Between the

Dual-mode Voices ........................................ 6

● Shifting a Dual-Mode Voice Up One Octave 6

● Memorizing the Balance & Octave Shift

Settings......................................................... 6

Reverb ...................................................................... 7

● Adjusting Reverb Depth................................ 7

● Memorizing the Reverb Type & Depth

Settings......................................................... 7

Touch Sensitivity ................................................... 8

● Memorizing the Touch Sensitivity Setting..... 8

The Pedals ............................................................... 9

● Soft/Sostenuto (Left) Pedal........................... 9

● Damper (Right) Pedal ................................... 9

Transposition .......................................................... 9

Pitch Control ......................................................... 10

● Tuning Up ................................................... 10

● Tuning Down............................................... 10

● To Restore Standard Pitch ......................... 10

● Memorizing the Pitch Control Setting ......... 10

The Metronome & Tempo Control ................... 11

■ The Metronome................................................ 11

● Metronome Volume .................................... 11

● Metronome Time Signature ........................ 11

■ Tempo Control ................................................. 11

Using the Recorder.............................................. 12

■ Recording......................................................... 12

● Changing the Initial Settings ....................... 13

● Erasing the Recorded Data ........................ 13

■ Playback .......................................................... 13

● Fast Forward Playback ............................... 13

MIDI Functions...................................................... 14

● A Brief Introduction to MIDI......................... 14

●

MIDI “Messages” Transmitted &

Received by the Clavinova

........................... 14

● MIDI Transmit & Receive Channel

Selection ..................................................... 15

● MIDI Transmit Transpose ........................... 15

■ Other MIDI Functions....................................... 16

● Local Control ON/OFF ................................ 16

● Program Change ON/OFF.......................... 16

● Control Change ON/OFF ............................ 17

● The Multi-Timbre Mode............................... 17

● The MIDI Split & Left Local OFF Mode....... 18

● Bulk Data Dump.......................................... 18

Factory Preset Recall.......................................... 19

Troubleshooting................................................... 19

Options & Expander Modules ........................... 19

Keyboard Stand Assembly ....................................i

MIDI Data Format.....................................................v

Specifications ..........................................................v

MIDI Implementation Chart ..................................vi

The Control Panel

POWER

B0A0G0F0E0D0C0B-1A-1

C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 G2 A2 B2 C3 D3 E3 F3 A3 B3 C4 D4 E4 F4F2 G3

F2 G3

PHONES Jacks

(Bottom Panel)

Left voice shift up key

(See page 6)

Pitch control keys

(See page 11)

Transpose keys

(See page 9)

Balance keys (See page 6)

RECORDER

PLAY REC DEMO

ORGAN

HARPSI-

CHORD

E. PIANO

CLAVINOVA

TONE

METRONOME

PIANO

MIDI/

TRANSPOSE

TEMPO

MASTER VOLUME

32 120 280

MIN MAX

REVERB

ROOM

HALL 1

HALL 2

COSMIC

RECORDER

PLAY REC DEMO

ORGAN

HARPSI-

CHORD

E. PIANO

CLAVINOVA

TONE

METRONOME

PIANO

MIDI/

TRANSPOSE

TEMPO

MASTER VOLUME

32 120 280

MIN MAX

REVERB

ROOM

HALL 1

HALL 2

COSMIC

1 [POWER] Switch

Press the [POWER] switch once to turn the power

ON, a second time to turn the power OFF. When the

power is initially turned ON, the [PIANO] voice selec-

tor LED will light.

2 [MASTER VOLUME] Control

The [MASTER VOLUME] control adjusts the vol-

ume (level) of sound produced by the Clavinova’s

internal stereo sound system. The [MASTER VOL-

UME] control also adjusts headphone volume when a

pair of headphones is plugged into the PHONES jack

(page 4).

3 [TEMPO] Control

This control adjusts the tempo of the CLP-153SG met-

ronome function as well as the playback tempo of the

recorder function. The tempo range is from 32 to 280

quarter-note beats per minute.

4 [REVERB] Button

The [REVERB] button selects a number of digital

reverb effects that you can use for extra depth and

expressive power. See page 7 for details.

5 [METRONOME] Button

Turns the metronome sound on and off. The

[TEMPO] control, above, is used to set the tempo of

the metronome sound. More precise tempo settings can

be achieved by using the [METRONOME] button and

the CLP-153SG keyboard as described on page 11.

6 Voice Selectors

The CLP-153SG has five voice selectors. Simply press

any of the voice selectors to select the corresponding

voice. The voice selector LED will light to indicate

which voice is currently selected.

The CLP-153SG also has a DUAL mode in which two

voices can be played simultaneously across the full

range of the keyboard — see page 6 for details.

NOTE

• The PIANO voice is automatically selected

whenever the [POWER] switch is initially turned

ON.

7 RECORDER [PLAY] and [REC] Buttons

These buttons control the CLP-153SG recorder, letting

you record and play back just about anything you play

on the keyboard — up to a maximum of about 4,200

notes. See page 12 for details.

D6 E6 F6 G6 A6 B6 C7

G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6

Right voice shift up key

(See page 6)

Memory key

(See page 6, 7, 8, 10)

Soft/Sostenuto

pedal

Damper pedal

[DEMO] Button

Activates the demo playback mode in which you can

select playback of five pre-programmed demonstration

sequences. See page 5 for details.

9 [MIDI/TRANSPOSE] Button

The [MIDI/TRANSPOSE] button allows access to the

Clavinova’s TRANSPOSE function (to shift the pitch

of the entire keyboard up or down) and MIDI func-

tions. For details refer to “TRANSPOSITION” on

page 9, “TOUCH SENSITIVITY” on page 8, and

“MIDI FUNCTIONS” on page 14, respectively.

0 Pedals

The CLP-153SG’s soft/sostenuto (left) and damper

(right) pedals provide a range of expressive control

capabilities similar to the pedal functions on an acous-

tic piano. See page 9 for details.

● The Music Stand

If you will be using sheet music with your

Clavinova, raise the music stand built into its top

panel by lifting the rear edge of the music stand, then

flip down the music stand braces and engage them

with the corresponding recesses.

The music stand can be lowered after slightly lift-

ing it and folding the two brackets which support it

against the back of the stand.

AUX OUT

L/L+RR

Connections

2 AUX OUT L/L+R and R Jacks

Stereo System

These jacks are intended for use with an external tone generator module such as

the Yamaha DOU-10 Disk Orchestra Unit. The stereo outputs from the external

tone generator module are connected to the AUX IN L and R jacks, allowing the

sound of the tone generator to be reproduced via the Clavinova’s internal sound

system and speakers.

The AUX OUT L/L+R and R jacks deliver the output of the Clavinova for con-

nection to an instrument amplifier, mixing console, PA system, or recording equip-

ment. If you will be connecting the Clavinova to a monaural sound system, use

only the L/L+R jack. When a plug is inserted into the L/L+R jack only, the left-

and right-channel signals are combined and delivered via the L/L+R jack so you

don’t lose any of the Clavinova’s sound.

The Internal Amplifier & Speaker System

The CLP-153SG features a high-performance stereo amplifier delivering 20 watts per channel

to a pair of 16-cm speaker units.

NOTE

• The AUX OUT jack signal must never be returned to the AUX IN jacks, either

directly or through external equipment.

The MIDI IN connector receives MIDI data from an external MIDI device (such

as the DOU-10 Disk Orchestra Unit) which can be used to control the Clavinova.

The MIDI OUT connector transmits MIDI data generated by the Clavinova (e.g.

note and velocity data produced by playing the Clavinova keyboard).

More details on MIDI are given in “MIDI FUNCTIONS” on page 14.

1 AUX IN L and R Jacks

3 MIDI IN and OUT Connectors

● PHONES Jacks (Bottom Panel)

Two pairs of standard pair of stereo headphones can be plugged in here for pri-

vate practice or late-night playing. The internal speaker system is automatically

shut off when a pair of headphones is plugged into either of the PHONES jacks.

AUX IN

DOU-10

MIDI

IN OUT

DOU-10

MIDI

OUT

AUX IN

AUX OUT

R L/L+R

123

ZTurn Power On

After making sure that the Clavinova’s AC plug is properly inserted into a

convenient AC wall outlet, press the [POWER] switch located to the left of the

keyboard to turn the power ON.

When the power is turned ON, the [PIANO] voice selector LED will light

(the PIANO voice is automatically selected whenever the power is turned ON).

Initially set the [MASTER VOLUME] control about half way between the

“MIN” and “MAX” settings. Then, when you start playing, re-adjust the [MAS-

TER VOLUME] control for the most comfortable listening level.

Select the desired voice by pressing one of the voice selectors.

The Clavinova offers keyboard touch response, so the volume and timbre of

notes played can be controlled according to how “hard” you play the keys. The

amount of variation available depends on the selected voice.

You can also add reverb as desired by using the [REVERB] button (see page 7

for [REVERB] button operation).

POWER

XSet the Volume

CSelect a Voice

ORGAN

HARPSI-

CHORDE. PIANO

CLAVINOVA

TONE

PIANO

MASTER VOLUME

MIN MAX

Selecting & Playing Voices

BAdd Reverb As Required

Press the [DEMO] button to engage the demo mode — the voice selectors

will flash in sequence.

Press one of the flashing voice selectors to start playback of the correspond-

ing demo tune — featuring the voice normally selected by that voice selector

button. The demo tunes will play in sequence until stopped, starting with the

selected tune. The voice selector indicator will flash during demo playback.

Use the [MASTER VOLUME] control to adjust the volume.

NOTE

• The [TEMPO] control does not affect demo playback.

You can start playback of any other demo tune during playback by simply

pressing the corresponding voice selector. Playback will stop and the playback-

ready mode described in step 2, above, will be re-engaged if you press the voice

selector of the demo that is currently playing.

Press the [DEMO] button when you want to stop demo playback and return

to the normal play mode.

ZEngage the Demo Mode

DEMO

XSelect a Demo Tune

ORGAN

HARPSI-

CHORDE. PIANO

CLAVINOVA

TONE

PIANO

CSet the Volume

VPlay a Different Demo

B Stop the Demo

Playing the Demonstration Tunes

The CLP-153SG includes five demo tunes that effectively demonstrate its sound capabilities.

Here’s how you can select and play the demo tunes:

DEMO

MASTER VOLUME

MIN MAX

VPlay

The Demo Tunes

• [PIANO] button: Etude op. 10-5 “Black Keys” by F. F. Chopin

• [CLAVINOVA TONE] button: “Pavane pour une infante défunte” by M. J. Ravel

• [HARPSICHORD] button: “Le Coucou” by L. C. Daquin

• [ORGAN] button: “Jesu, Joy Of Man’s Desiring”

(Chorale from Cantata No. 147)

by J. S. Bach

* The demonstartion pieces listed above are short excerpts from the original compositions.

The Dual Mode

The DUAL mode makes it possible to play two voices simultaneously across the entire range

of the keyboard. To activate the DUAL mode simply press two voice selectors at the same time

(or press one voice selector while holding another). The voice indicators of both selected voices

will light when the DUAL mode is active. To return to the normal single-voice play mode, press

any single voice selector.

● Adjusting the Balance Between

the Dual-mode Voices

The volume levels of the two voices combined in the DUAL mode

are normally set automatically to produce a pleasing balance (see

“Default Settings” below). The balance can be adjusted manually by

using the C2 through C4 keys on the keyboard while pressing the two

voice selectors corresponding to the voices to be combined in the

DUAL mode.

The C3 key produces equal (50:50) balance between the two

voices, while keys to the left of C3 increase the volume of the left

voice in relation to the right voice, and keys to the right of C3 in-

crease the volume of the right voice in relation to the left voice. By

“left” and “right” voice we refer to the relative positions of the voice

selectors — i.e. in a HARPSICHORD/ORGAN combination HARP-

SICHORD is the left voice and ORGAN is the right voice.

Default Settings

Voice Combinations Balance keys

PIANO/ORGAN ....................... F2

CLAVINOVA TONE/ORGAN ... F2

E. PIANO/ORGAN ................... F2

HARPSICHORD/ORGAN ........ G2

* All other voice combinations are set to C3 (equal balance).

Depending on which voices you combine using the DUAL mode,

the combination may sound better if one of the voices is shifted up an

octave. To shift the right voice, press the C5 key while pressing the

two voice selectors corresponding to the voices to be combined in the

DUAL mode. Press C5 again to shift the voice back to its normal

range. Use the C1 key in the same way to shift the left voice.

All voice combinations are set to the same octave by default.

Equal

balance.

Left voice

maximum.

Right voice

maximum.

ORGAN

HARPSI-

CHORDPIANO

● Shifting a Dual-Mode Voice Up

One Octave

Left voice

shift up.

Right voice

shift up.

ORGAN

HARPSI-

CHORDPIANO

● Memorizing the Balance &

Octave Shift Settings

Press the C7 key while holding any two voice selectors to memo-

rize all balance, and octave shift settings made since the power was

turned on. The memorized settings will be retained in memory for

about one week after the power is turned off, then the default settings

will be restored. To keep the memorized settings for longer periods,

turn the power on briefly at least once a week.

If these settings are not memorized as described above, they are

retained in memory only until the Clavinova is turned off.

ORGAN

HARPSI-

CHORDPIANO

Reverb

The [REVERB] button selects a number of digital reverb effects that you can use for extra depth and

expressive power.

To select a reverb type press the [REVERB] button a few times until the indicator corresponding to the

desired type lights (the indicators light in sequence each time the [REVERB] button is pressed). No reverb

is produced when all indicators are off.

OFF ............When no reverb effect is selected (no REVERB indicator is lit), a special natural

damper effect is applied to the piano voice. This simulates the natural resonance of

an acoustic piano’s strings and sound board when the damper pedal is pressed.

ROOM........This setting add a continuous reverb effect to the sound that is similar to the type of

acoustic reverberation you would hear in a medium-size room.

HALL 1 ......For a “bigger” reverb sound, use the HALL 1 setting. This effect simulates the natu-

ral reverberation of a medium-size concert hall.

HALL 2 ......For a really spacious reverb sound, use the HALL 2 setting. This effect simulates the

natural reverberation of a large concert hall.

COSMIC ....The COSMIC reverb effect produces an echo-plus-reverb sound that can add life and

animation to your music.

● Adjusting Reverb Depth

The depth of the selected reverb effect can be adjusted for the current

voice by using the C2 through C4 keys on the keyboard while holding the

[REVERB] button. The C3 key sets the “normal” depth for the selected

effect. Keys to the left of C3 decrease the reverb depth, while keys to the

right of the C3 key increase the reverb depth. Separate reverb settings can

be made for each effect and voice, and these settings are retained in

memory until the power is turned off. The depth of the natural damper ef-

fect is fixed.

Default Settings

Normal

depth.

Decrease

depth.

Increase

depth.

REVERB

ROOM

HALL 1

HALL 2

COSMIC

* All effect types set to C3 for all other voices.

* The default reverb type is ROOM.

Press the C7 key while holding the [REVERB] button to memorize the

current effect type and all depth settings made since the power was turned

on. The memorized settings will be retained in memory for about one week

after the power is turned off, then the default settings will be restored. To

keep the memorized settings for longer periods, turn the power on briefly at

least once a week.

If these settings are not memorized as described above, they are retained

in memory only until the Clavinova is turned off.

● Memorizing the Reverb

Type & Depth Settings

REVERB

ROOM

HALL 1

HALL 2

COSMIC

ROOM HALL 1 HALL 2

COSMIC

PIANO G2 G2 G2 G2

ORGAN C3 C3 F3 E3

Four different types of keyboard touch sensitivity — HARD, MEDIUM, SOFT or FIXED —

can be selected to match different playing styles and preferences. The different touch sen-

sitivity settings are selected by using the [MIDI/TRANSPOSE] and [REVERB] buttons.

Touch Sensitivity

HARD (ROOM indicator) ...........The HARD setting requires the keys to be played quite hard to produce maxi-

mum loudness.

MEDIUM (HALL 1 indicator)......The MEDIUM setting produces a fairly “standard” keyboard response. This is

the initial factory default setting.

SOFT (HALL 2 indicator) ...........The SOFT setting allows maximum loudness to be produced with relatively

light key pressure.

FIXED (No indicator lit)..............All notes are produced at the same volume no matter how hard the keyboard is

played. This is an ideal setting for voices which normally have no keyboard

sensitivity (i.e. harpsichord and organ).

To select a touch sensitivity setting press the [REVERB] button a few

times while holding the [MIDI/TRANSPOSE] button until the indicator

corresponding to the desired setting lights.

Press the C7 key while holding the [MIDI/TRANSPOSE] and [RE-

VERB] button to memorize the current touch sensitivity setting. The

memorized setting will be retained in memory for about one week after the

power is turned off, then the default setting (MEDIUM) will be restored. To

keep the memorized setting for longer periods, turn the power on briefly at

least once a week.

If this setting is not memorized as described above, it is retained in

memory only until the Clavinova is turned off.

MIDI/

TRANSPOSE

REVERB

ROOM

HALL 1

HALL 2

COSMIC

● Memorizing the Touch Sen-

sitivity Setting

MIDI/

TRANSPOSE

REVERB

ROOM

HALL 1

HALL 2

COSMIC

The Pedals

The CLP-153SG has two foot pedals that produce a range of expressive effects similar to

those produced by the pedals on an acoustic piano.

The [MIDI/TRANSPOSE] button and keys F#2 through F#3 on the keyboard are used for transposition.

ZPress and hold the [MIDI/TRANSPOSE] button.

XPress a key between F#2 and F#3 according to the desired amount of

transposition.*

CRelease the [MIDI/TRANSPOSE] button.

* Pressing the C3 key produces normal keyboard pitch. Pressing the key to

the left of C3 (B2) transposes the pitch of the keyboard down a semitone,

the next key to the left (Bb2) transposes down a whole tone (two semi-

tones), etc., down to the F#2 key which transposes down 6 semitones.

Upward transposition is accomplished in the same way using the keys to

the right of C3, up to F#3 which transposes up 6 semitones.

NOTE

• Notes below and above the A-1 — C7 of the Clavinova sound one oc-

tave higher and lower, respectively.

The Clavinova’s TRANSPOSE function makes it possible to shift the pitch of the entire key-

board up or down in semitone intervals up to a maximum of six semitones. “Transposing” the

pitch of the Clavinova keyboard facilitates playing in difficult key signatures, and you can easily

match the pitch of the keyboard to the range of a singer or other instrumentalist.

Transposition

When the power is turned on the left pedal is set for soft pedal operation.

Pressing the soft pedal reduces the volume and slightly changes the timbre

of notes played.

The left pedal can be switched to sostenuto operation by pressing the

pedal while holding the [MIDI/TRANSPOSE] button. If you play a note or

chord on the keyboard and press the sostenuto pedal while the note(s) are

held, those notes will be sustained as long as the pedal is held (as if the

damper pedal had been pressed) but all subsequently played notes will not

be sustained. This makes it possible to sustain a chord, for example, while

other notes are played “staccato.” You can switch back to soft pedal opera-

tion at any time simply by pressing the pedal while holding the [MIDI/

TRANSPOSE] button again.

The damper pedal functions in the same way as a damper pedal on an

acoustic piano. When the damper pedal is pressed notes played have a long

sustain. When no REVERB effect is selected and a piano voice is selected,

the damper pedal also produces a special “resonance” that simulates the

ring of the strings and the sound board of an acoustic piano. Releasing the

pedal immediately stops (damps) any sustained notes.

● Soft/Sostenuto (Left) Pedal

Soft/Sostenuto pedal

● Damper (Right) Pedal

MIDI/

TRANSPOSE

Normal

pitch.

Transpose

down.

Transpose

up.

-5 -3 -1 0 +2 +4 +5

-6 -4 -2 +1

+3 +6

Damper pedal

Pitch Control

● Tuning Up

ZTo tune up (raise pitch), hold the A-1 and B-1 keys simultaneously.

XPress any key between C3 and B3. Each time a key in this range is

pressed the pitch is increased by approximately 1.2 cents, up to a maxi-

mum of 50 cents above standard pitch.

CRelease the A-1 and B-1 keys.

ZTo tune down (lower pitch), hold the A-1 and A#-1 keys simultane-

ously.

XPress any key between C3 and B3. Each time a key in this range is

pressed the pitch is decreased by approximately 1.2 cents, up to a maxi-

mum of 50 cents below standard pitch.

CRelease the A-1 and A#-1 keys.

ZTo restore standard pitch (A3 = 440 Hz), hold the A-1, A#-1 and B-1

keys simultaneously.

XPress any key between C3 and B3.

CRelease the A-1, A#-1 and B-1 keys.

NOTE

• The PITCH CONTROL function has no effect when LOCAL OFF is

active (see “MIDI FUNCTIONS,” page 14).

Pitch control makes it possible to tune the Clavinova over a ±50-cent range in approximately

1.2-cent intervals. A hundred “cents” equals one semitone, so the tuning range provided allows

fine tuning of overall pitch over a range of approximately a semitone. Pitch control is useful for

tuning the Clavinova to match other instruments or recorded music.

● Tuning Down

-1

● To Restore Standard Pitch

-1

● Memorizing the Pitch Con-

trol Setting

Press the C7 key while holding the A-1/B-1, A-1/A#-1, or A-1/A#-1/B-1

key combination to memorize the current pitch control setting. The memo-

rized setting will be retained in memory for about one week after the power

is turned off, then the standard pitch will be restored. To keep the memo-

rized setting for longer periods, turn the power on briefly at least once a

week.

If this setting is not memorized as described above, it is retained in

memory only until the Clavinova is turned off.

The Metronome & Tempo Control

The CLP-153SG built-in metronome is a convenient feature for practice, and it can also pro-

vide a solid rhythmic guide when recording using the Recorder feature, described below.

The Metronome

The metronome sound is turned on and off via the [METRONOME]

button. Press the [METRONOME] button so that its indicator lights to turn

the metronome on, then again so the indicator goes out to turn the metro-

nome off.

The volume of the metronome sound can be independently adjusted by

using the [TEMPO] control while holding the [METRONOME] button.

Sliding the control to the right increases the metronome volume.

The time signature of the metronome sound can be set by pressing the

appropriate voice selector button while holding the [METRONOME] but-

ton, as follows:

METRONOME

● Metronome Volume

METRONOME

TEMPO

32 120 280

Key Tempo

A-1 32

A#-1 34

B-1 36

C0 38

C#040

D0 42

D#044

E0 46

F0 48

F#050

G0 52

Key Tempo

G#054

A0 56

A#058

B0 60

C1 62

C#164

D1 66

D#168

E1 70

F1 72

F#174

Key Tempo

G1 76

G#178

A1 80

A#182

B1 84

C2 86

C#288

D2 90

D#292

E2 94

F2 96

Key Tempo

F#298

G2 100

G#2 102

A2 104

A#2 106

B2 108

C3 110

C#3 112

D3 114

D#3 116

E3 118

Key Tempo

F3 120

F#3 122

G3 124

G#3 126

A3 128

A#3 130

B3 132

C4 134

C#4 136

D4 138

D#4 140

Key Tempo

E4 142

F4 144

F#4 146

G4 148

G#4 150

A4 152

A#4 154

B4 156

C5 158

C#5 160

D5 164

Key Tempo

D#5 168

E5 172

F5 176

F#5 180

G5 184

G#5 188

A5 192

A#5 196

B5 200

C6 204

C#6 208

Key Tempo

D6 212

D#6 216

E6 220

F6 224

F#6 232

G6 240

G#6 248

A6 256

A#6 264

B6 272

C7 280

Tempo/Key Chart

METRONOME

TEMPO

32 120 280

Tempo Control

The tempo of the metronome and recorder playback can be controlled in

two ways:

■ Use the panel [TEMPO] control to set the required tempo from 32 to

280 quarter-note beats per minute.

■ For more precise tempo settings press the appropriate key on the key-

board while holding the [METRONOME] button.

[METRONOME] + [PIANO] No accent (default)

[METRONOME] + [CLAVINOVA TONE] 2 time

[METRONOME] + [E. PIANO] 3 time

[METRONOME] + [HARPSICHORD] 4 time

[METRONOME] + [ORGAN] 6 time

● Metronome Time Signature

ORGAN

HARPSI-

CHORDE. PIANO

CLAVINOVA

TONE

METRONOME

PIANO

Using the Recorder

The CLP-153SG recorder lets you record what you play on the keyboard and then play it back. This is a

useful adjunct to any keyboard study program, since it lets you hear exactly how you sound from the listen-

er’s perspective. It can also be just plain fun.

The recorder actually records the following data:

● Notes played ● Voice selection ● Dual mode voices ● Dual balance

● Damper pedal ● Left pedal ● Tempo

(Initial setting only.)

● Reverb type ● Reverb depth

Recording

Press the RECORDER [REC] button to engage the record ready mode

(recording does not actually start yet). The [REC] button indicator will

light.

Before actually beginning to record, select the voice you want to record

with (or voices if you will be using the dual mode). You might also want to

set the volume and tempo controls.

Recording will begin automatically as soon as you play a note on the

keyboard or press the [PLAY] button.

NOTE

• If the metronome was on when you started recording, you’ll be able to

keep time with the metronome while recording, but the metronome

sound will not be recorded.

• You can record up to a maximum of about 4,200 notes, depending on

pedal usage and other factors. The [REC] button indicator will begin to

flash when recorder memory is almost full, and recording will stop auto-

matically.

Press either the RECORDER [REC] or [PLAY] button to stop record-

ing.

Engage the Record Ready

Mode

RECORDER

PLAY REC

Make All Necessary Initial

Settings

ORGAN

HARPSI-

CHORDE. PIANO

CLAVINOVA

TONE

PIANO

C Start Recording

VStop Recording

RECORDER

PLAY REC

The initial voice (including dual mode), damper pedal, soft pedal, and

tempo settings made in step 2 of the recording procedure are actually re-

corded by the CLP-153SG. These initial settings can be changed after the

recording is finished by pressing the [REC] button to engage the record

ready mode, making the required changes, and then pressing the [REC]

button again to exit from the record ready mode and register the changes. If

you do this, be careful not to press the [PLAY] button or a key on the key-

board, either of which will start recording and erase all previous recorded

data.

● Changing the Initial Settings

The recorded data can be erased by first pressing the [REC] button to

engage the record ready mode, and then pressing the [PLAY] button twice

without recording any data.

● Erasing the Recorded Data

Playback

To play back what you’ve recorded, simply press the RECORDER

[PLAY] button. Playback starts from the beginning of the recorded data,

and will stop automatically at the end of the recorded data. You can also

stop playback at any time by pressing the [PLAY] button.

NOTE

• It is possible to play along on the keyboard during playback.

• The playback volume and tempo can be adjusted by using the [MASTER

VOLUME] and [TEMPO] controls, respectively.

• If the metronome is being used during playback, the metronome will stop

when playback is stopped.

• The playback data is not transmitted via the MIDI OUT connector.

• All recorder data will be retained in memory for about one week after the

power is turned off. If you want to keep your recorded data for longer

periods, turn the power on briefly at least once a week. It is also possible

to store it to an external MIDI storage device such as the Yamaha DOU-

10 Disk Orchestra Unit by using the Bulk Dump function described on

page 18.

When you want to locate a specific point in a recording you can quickly

move forward through the recording while monitoring the sound by press-

ing the [REC] button while holding the [MIDI/TRANSPOSE] button.

RECORDER

PLAY REC

● Fast Forward Playback

MIDI/

TRANSPOSE

RECORDER

PLAY REC

DOU-10

Data Being Recorded

Playback Data

MIDI IN MIDI INMIDI OUTMIDI OUT

DOU-10

MIDI Cable

MIDI INMIDI OUT

● A Brief Introduction to MIDI

MIDI, the Musical Instrument Digital Interface, is a world-standard com-

munication interface that allows MIDI-compatible musical instruments and

equipment to share musical information and control one another. This

makes it possible to create “systems” of MIDI instruments and equipment

that offer far greater versatility and control than is available with isolated

instruments. For example, most MIDI keyboards (including the Clavinova,

of course) transmit note and velocity (touch response) information via the

MIDI OUT connector whenever a note is played on the keyboard. If the

MIDI OUT connector is connected to the MIDI IN connector of a second

keyboard (synthesizer, etc.) or a tone generator (essentially a synthesizer

with no keyboard), the second keyboard or tone generator will respond

precisely to notes played on the original transmitting keyboard. The result is

that you can effectively play two instruments at once, providing thick multi-

instrument sounds.

This same type of musical information transfer is used for MIDI se-

quence recording. A sequence recorder can be used to “record” MIDI data

received from a Clavinova, for example. When the recorded data is played

back, the Clavinova automatically “plays” the recorded performance in

precise detail.

The examples given above really only scratch the surface. MIDI can do

much, much more. The CLP-153SG offers a number of MIDI functions that

allows it to be used in fairly sophisticated MIDI systems.

NOTE

• Always use a high-quality MIDI cable to connect MIDI OUT to MIDI IN

terminals. Never use MIDI cables longer than about 15 feet, since cables

longer than this can pick up noise which can cause data errors.

● MIDI “Messages” Transmitted

& Received by the Clavinova

Note and Velocity Data

This information tells the receiving keyboard or tone generator to play a certain note (specified by the MIDI

note number) at a certain dynamic level (specified by the MIDI velocity value). Note and velocity data is trans-

mitted by the Clavinova whenever a key is pressed, and the Clavinova’s internal AWM tone generator will

“play” the corresponding note(s) whenever note and velocity data is received from an external MIDI device.

Program Change Numbers

The CLP-153SG transmits a MIDI program change number between 0 and 4 when one of its voice selectors is

pressed. This normally causes the correspondingly numbered voice to be selected on a receiving MIDI device.

The Clavinova will respond in the same way, automatically selecting the appropriate voice when a MIDI pro-

gram change number is received. See “Program Change ON/OFF” on page 16 for information on turning pro-

gram change number reception and transmission ON or OFF.

Control Change Numbers

Control Change data representing Damper pedal operation is transmitted by the Clavinova whenever one of

these pedals is used. If the receiving device is a tone generator or another keyboard, it will respond in the same

way as the Clavinova’s internal tone generator when one of the pedals is used. The Clavinova also receives and

responds to the appropriate control change data. See “Control Change ON/OFF” on page 17 for information on

turning control change number reception and transmission ON or OFF.

The MIDI information (messages) transmitted and received by the

Clavinova are as follows:

MIDI Functions

Clavinova

MIDI/

TRANSPOSE

-6 -4 -2 +1

+3 +6

+5+4+20-1-3-5

DOU-10

Tone Generator

MIDI IN

MIDI OUT

MIDI THRU

MIDI/

TRANSPOSE

1356810121315

2 4 7 9 11 14 16

1356810121315

2 4 7 9 11 14 16

● MIDI Transmit & Receive

Channel Selection

The MIDI system allows transmission and reception of MIDI data on 16

different channels. Multiple channels have been implemented to allow se-

lective control of certain instruments or devices connected in series. For

example, a single MIDI sequence recorder could be used to “play” two

different instruments or tone generators. One of the instruments or tone

generators could be set to receive only on channel 1, while the other is set

to receive on channel 2. In this situation the first instrument or tone genera-

tor will respond only to channel-1 information transmitted by the sequence

recorder, while the second instrument or tone generator will respond only to

channel-2 information. This allows the sequence recorder to “play” two

completely different parts on the receiving instruments or tone generators.

In any MIDI control setup, the MIDI channels of the transmitting and

receiving equipment must be matched for proper data transfer. An “OMNI”

receive mode is also available, which allows reception on all 16 MIDI chan-

nels. In the OMNI mode it is not necessary to match the receive channel of

the receiving device to the transmit channel of the transmitting device (ex-

cept when receiving mode messages).

Setting the Clavinova MIDI Channels

ZPress and hold the [MIDI/TRANSPOSE] button.

XPress the key on the keyboard corresponding to the desired MIDI trans-

mit or receive channel.*

CRelease the [MIDI/TRANSPOSE] button.

* Keys C1 through D#2 on the keyboard are used to set the MIDI transmit

channel, and keys C4 through D#5 are used to turn the OMNI mode OFF

and set the MIDI receive channel as shown in the illustration to the left.

The E5 key sets the OMNI receive mode and basic receive channel 1.

NOTE

• When the power is initially turned ON, MIDI receive is set to the OMNI

mode and the transmit channel is set to 1.

This function allows the MIDI note data transmitted by the Clavinova to

be transposed up or down in semitone increments by up to plus or minus 6

semitones. The pitch of the Clavinova itself is not affected.

Setting the MIDI Transpose Function

ZPress and hold the [MIDI/TRANSPOSE] button.

XPress the key on the keyboard corresponding to the desired amount of

transposition.*

CRelease the [MIDI/TRANSPOSE] button.

* Keys F#5 through F#6 on the keyboard are used to set the MIDI transmit

transpose function as shown in the illustration to the left.

NOTE

• When the power is turned ON, MIDI transmit transpose is set to 0 (no

transposition).

● MIDI Transmit Transpose

For setting the transmit

channel. (C1 ~ D#2)

For setting the receive

channel. (C4 ~ D#5)

(Set to receive on MIDI

channel 2)

For OMNI mode

Clavinova

(Set to receive on MIDI channel 1)

E. PIA

CLAVINOVA

TONE

PIANO

MIDI/

TRANSPOSE

CLAVINOVA

TONE

CLAVINOVA

TONE

MIDI Functions

Other MIDI Functions

The MIDI functions listed to the right are engaged by

holding down the [MIDI/TRANSPOSE] button and press-

ing the corresponding voice selector. Full details are given

in the following pages.

Function

CLP-153

Voice Selector

Local Control ON/OFF [PIANO]

Program Change ON/OFF [CLAVINOVA TONE]

Control Change ON/OFF [E. PIANO]

Multi-Timbre Mode [HARPSICHORD]

MIDI Split & Left Local OFF [ORGAN]

MIDI FUNCTION CHART

“Local Control” refers to the fact that, normally, the Clavinova keyboard controls its internal tone generator,

allowing the internal voices to be played directly from the keyboard. This situation is “Local Control ON” since

the internal tone generator is controlled locally by its own keyboard.

Local control can be turned OFF, however, so that the Clavinova keyboard does not play the internal voices,

but the appropriate MIDI information is still transmitted via the MIDI OUT connector when notes are played on

the keyboard. At the same time, the internal tone generator responds to MIDI information received via the MIDI

IN connector.

When using the DOU-10 Disk Orchestra Unit with the Clavinova, for example, Local Control should be

turned OFF when recording using the DOU-10 voices only, and ON when recording the Clavinova voices while

listening to playback of the DOU-10 voices.

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [PIANO] voice selector. If the PIANO LED is lit when the

[PIANO] voice selector is pressed, you have turned local control OFF.

If the PIANO LED is not lit when the [PIANO] voice selector is

pressed, you have turned local control ON.

CRelease the [MIDI/TRANSPOSE] button.

● Local Control ON/OFF

Normally the Clavinova will respond to MIDI program change numbers received from an external keyboard

or other MIDI device, causing the correspondingly numbered Clavinova voice to be selected. The Clavinova

will normally also send a MIDI program change number whenever one of its voices is selected, causing the cor-

respondingly numbered voice or program to be selected on the external MIDI device if the device is set up to

receive and respond to MIDI program change numbers.

This function makes it possible to cancel program change number reception and transmission so that voices

can be selected on the Clavinova without affecting the external MIDI device, and vice versa.

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [CLAVINOVA TONE] voice selector. If the CLAVINOVA

TONE LED is lit when the [CLAVINOVA TONE] voice selector is

pressed, you have turned program change reception/transmission OFF.

If the CLAVINOVA TONE LED is not lit when the [CLAVINOVA

TONE] voice selector is pressed, you have turned program change

reception/transmission ON.

CRelease the [MIDI/TRANSPOSE] button.

● Program Change ON/OFF

E. PIA

CLAVINOVA

TONE

PIANO

MIDI/

TRANSPOSE

PIANO

= Local Control OFF

= Local Control ON

= Program Change OFF

= Program Change ON

E. PIANO

MIDI/

TRANSPOSE

HARPSI-

CHORDE. PIANO

Normally the Clavinova will respond to MIDI control change data received from an external MIDI device or

keyboard, causing the selected Clavinova voice to be affected by pedal and other “control” settings received

from the controlling device. The Clavinova also transmits MIDI control change information when one of its

pedals are operated.

This function makes it possible to cancel control change data reception and transmission if you do not want

the Clavinova voices to be affected by control change data received from an external device or vice versa.

● Control Change ON/OFF

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [E. PIANO] voice selector. If the E. PIANO LED is lit when

the [E. PIANO] voice selector is pressed, you have turned control

change reception/transmission OFF. If the E. PIANO LED is not lit

when the [E. PIANO] voice selector is pressed, you have turned control

change reception/transmission ON.

CRelease the [MIDI/TRANSPOSE] button.

The Multi-Timbre mode is a special mode in which the Clavinova voices

can be independently controlled on different MIDI channel numbers by an

external MIDI device. The Multi-Timbre mode can be activated as follows:

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [HARPSICHORD] voice selector. If the HARPSICHORD

LED is lit when the [HARPSICHORD] voice selector is pressed, you

have turned the Multi-Timbre mode ON. If the HARPSICHORD LED

is not lit when the [HARPSICHORD] voice selector is pressed, you

have turned the Multi-Timbre mode OFF.

CRelease the [MIDI/TRANSPOSE] button.

● The Multi-Timbre Mode

= Control Change OFF

= Control Change ON

MIDI/

TRANSPOSE

HARPSI-

CHORDE. PIANO

HARPSI-

CHORD

HARPSI-

CHORD

= Multi-Timbre Mode ON

= Multi-Timbre Mode OFF

MIDI/

TRANSPOSE

ORGAN

HARPSI-

CHORD

IANO

MIDI Functions

In the MIDI split mode one section of the Clavinova keyboard is used to play a Clavinova voice in the normal

way, while the remaining section is used to play a second MIDI keyboard or tone generator such as the Yamaha

DOU-10 Disk Orchestra Unit. In this mode the right-hand section of the keyboard is used to play an internal

Clavinova voice, while the left-hand section of the keyboard plays the external keyboard or tone generator.

Playing the left-hand section of the keyboard produces no sound from the Clavinova. The “split point,” or the

key that divides the left- and right-hand sections of the keyboard can be set at any desired key.

● The MIDI Split & Left Local OFF Mode

The MIDI split mode is useful if, for example, you want to play a piano

(Clavinova) voice with the right hand while playing a synthesizer bass line

or string section with the left hand.

When the MIDI split mode is activated, notes played on the left-hand

section are transmitted via the Clavinova MIDI OUT connector on MIDI

channel 2. Notes played on the right-hand section are transmitted on the

“basic channel” (i.e. the channel set using the MIDI channel selection func-

tion described previously).

ZPress the [ORGAN] voice selector while holding down the [MIDI/

TRANSPOSE] button. The ORGAN LED will flash.

XWhile still holding the [MIDI/TRANSPOSE] button, press the key on

the keyboard at which you want to set the split point. The ORGAN

LED will light continuously. The split-point becomes the first key of

the left-hand section.

CRelease the [MIDI/TRANSPOSE] button.

VTo return to the normal full-keyboard mode, hold the [MIDI/TRANS-

POSE] button and press the [ORGAN] voice selector, then release both

buttons.

NOTE

• When the power is turned ON the default split point key — F

2 — will be

automatically selected. If a new split point is selected it remains active

until the power is turned OFF or a different split point is selected.

▼

Left-hand section plays

a DOU-10 bass voice.

Right-hand section plays a

Clavinova piano voice.

SPLIT POINT

● Bulk Data Dump

This function is used to transmit all data stored in the Recorder memory

to a MIDI data storage device such as the Yamaha DOU-10 Disk Orchestra

Unit, other sequence recorders, or MIDI compatible computers.

ZHold [MIDI/TRANSPOSE] and press the [PLAY] button. Transmis-

sion will begin.

XRelease the buttons.

NOTE

• Bulk dump will not function when the metronome is on or when the re-

corder is in operation.

DOU-10

OUT PUT

AUX IN

RMIDI OUT

MIDI

(Set to receive on

MIDI channel 2)

Clavinova

MIDI/

TRANSPOSE

RECORDER

PLAY REC

Factory Preset Recall

All dual mode, reverb, touch sensitivity, and pitch control settings can be

restored to their original factory preset values by holding the C7 key while

turning the [POWER] switch ON. This also erases all recorder data.

POWER

1. No Sound When the Power is Turned ON

Is the AC plug properly connected to an AC wall outlet? Check the AC connection carefully. Is the MASTER

VOLUME control turned up to a reasonable listening level?

This can occur if there is a high-power transmitter in your vicinity. Contact your Yamaha dealer.

This is usually due to turning ON or OFF a household appliance or other electronic equipment which is fed by

the same AC mains line as your Clavinova.

The Clavinova contains digital circuitry which can generate radio-frequency noise. The solution is to move the

Clavinova further away from the affected equipment, or vice versa.

If the Clavinova is connected to a stereo system or instrument amplifier and the sound is distorted, reduce the

setting of the Clavinova volume control to a level at which the distortion ceases.

Troubleshooting

If you encounter what appears to be a malfunction, please check the following

points before assuming that your Clavinova is faulty.

2. The Clavinova Reproduces Radio or TV Sound

3. Intermittent Static Noise

4. Interference Appears On Radio or TV Sets Located Near the Clavinova

5. Distorted Sound When the Clavinova is Connected to An External Amplifier/Speaker System

● Options

BC-8 Bench

A comfortable bench styled to match your Yamaha Clavinova.

HPE-160 Stereo Headphones

High-performance lightweight dynamic headphones with extra-soft ear pads.

KC-883 Key Cover

A convenient way to keep your keyboard clean and dust-free.

Options & Expander Module

DOU-10 Disk Orchestra Unit

A range of MIDI recording and playback functions, plus Yamaha Disk Orchestra

Collection, Disklavier PianoSoft™, General MIDI, and Standard MIDI File disk

playback capability.

● Expander Module

Keyboard Stand Assembly

NOTE

• We do not recommend attempting to assemble the

Clavinova alone. The job can be easily accom-

plished, however, with only two people.

• Use only the screws provided or replacements of

exactly the specified size. Using screws of the wrong

size can result in damage to the instrument.

Z Open the box and remove all the parts.

On opening the box you should find the parts shown in

the illustration above. Check to make sure that all the re-

quired parts are provided.

Attach the side panels (D) to the pedal

box (C).

Before installing the pedal box, untie and straighten out

the bundled cord attached to the bottom of the pedal box.

Place the pedal box on top of the wooden blocks at-

tached to the side panels (D), and attach using the four 6 x

25 millimeter round-head screws 1 — two screws on each

side. Make sure the pedals extend in the same direction as

the feet.

Attach the center panel (B) to the side

panels (D).

The center panel (B) should be screwed to the brackets

on the side panels (D) using the four 4 x 25 millimeter

round-head screws 2, as shown in the illustration. Make

sure the center panel is attached to the side of the brackets

facing the pedals.

HINWEIS

• Wir raten davon ab, das Clavinova alleine

zusammenzubauen und aufzustellen. Zwei Personen

können diese Arbeit jedoch problemlos ausführen.

• Verwenden Sie ausschließlich die mitgelieferten

Schrauben oder Ersatzschrauben identischer Größe.

Die Verwendung von Schrauben mit abweichenden

Maßen kann eine Beschädigung des Instruments zur

Folge haben.

Öffnen Sie den Karton und nehmen Sie

alle Teile heraus.

Im Karton sollten die oben abgebildeten Teile enthalten

sein. Prüfen Sie zunächst bitte, ob alle Teile vollständig vor-

handen sind.

Schrauben Sie den Pedalkasten (C) an

den Seitenwänden (D) fest.

Bevor Sie den Pedalkasten montieren, nehmen Sie zu-

nächst das gebündelte Kabel aus dem Pedalkasten, entfernen

den Kabelbinder und ziehen das Kabel dann gerade aus.

Setzen Sie den Pedalkasten auf die Holzklötze an den

Seitenwänden (D), und schrauben Sie ihn dann mit den vier 6

x 25 mm Halbrundschrauben 1 fest (jeweils zwei Schrauben

links und rechts). Achten Sie dabei darauf, daß die Pedale in

dieselbe Richtung weisen wie die vorspringenden Teile der

Füße.

Schrauben Sie die Rückwand (B) an die

beiden Seitenwände (D).

Die Rückwand (B) wird mit den vier 4 x 25 mm Halbrund-

schrauben 2 an den Winkelblechen der Seitenwände (D)

festgeschraubt, wie in der Abbildung gezeigt. Achten Sie

bitte darauf, daß die Rückwand an den pedalseitigen Flächen

der Winkelbleche angebracht wird.

Zusammenbau und Aufstellung

6 x 25 mm round-head screws x 4 1

6 x 25 mm Halbrundschrauben x 4 1

Vis à tête ronde de 6 x 25 mm x 4 1

Tornillos de cabeza redonda

de 6 x 25 mm x 4 1

4 x 25 mm round-head screws x 4 2

4 x 25 mm Halbrundschrauben x 4 2

Vis à tête ronde de 4 x 25 mm x 4 2

Tornillos de cabeza redonda

de 4 x 25 mm x 4 2

6 x 16 mm flat-head screws x 4 3

6 x 16 mm Senkschrauben x 4 3

Vis à tête plate de 6 x 16 mm x 4 3

Tornillos de cabeza plana de

6 x 16 mm x 4 3

2 3

Assemblage du support de clavier

REMARQUE

• Nous ne vous conseillons pas d’essayer d’assembler

le Clavinova seul. Toutefois, ce travail peut être

facilement exécuté par deux personnes.

• N’utilisez que les vis fournies ou des vis ayant

exactement les mêmes dimensions. L’utilisation de

vis de dimensions incorrectes pourrait endommager

l’instrument.

Ouvrez le carton et retirez toutes les

pièces

Les pièces indiquées sur l’illustration devraient toutes se

trouver dans le carton. Vérifiez qu’il n’en manque aucune.

Fixez les panneaux latéraux (D) au

pédalier (C)

Avant de poser le pédalier, détacher le cordon de la

partie inférieure du pédalier et le dérouler.

Placez le pédalier sur les cales en bois fixées aux

panneaux latéraux (D) et fixez-le à l’aide des quatre vis à

tête ronde de 6 x 25 millimètres 1: deux vis de chaque

côté. Veillez à ce que les pédales soient dirigées dans le

même sens que les supports inférieurs.

Fixez le panneau central (B) aux

panneaux latéraux (D)

Le panneau central (B) doit être fixé aux ferrures des

panneaux latéraux (D) de la manière illustrée à l’aide des

quatre vis à tête ronde de 4 x 25 millimètres 2. Veillez à

ce que le panneau central soit fixé aux ferrures côté pédale.

Conjunto del soporte del teclado

NOTA

• No le recomendamos que intente montar la

Clavinova usted solo. El trabajo puede ser realizado

fácilmente entre dos personas.

• Utilice sólo los tornillos suministrados o reemplazos

del exacto tamaño especificado. El empleo de

tornillos de un tamaño erróneo puede dañar el

instrumento.

Z Abra la caja y extraiga todas las partes.

Al abrir la caja deberá encontrar todas las partes

mostradas en la ilustración. Compruebe para asegurarse

que se proporcionan todas las partes necesarias.

Acople los paneles laterales (D) en la

caja de pedales (C).

Antes de instalar la caja de pedales, desate y enderezca

el cable plegado unido a la parte inferior de la caja de

pedales.

Ponga la caja de pedales encima de los bloques de

madera unidos a los paneles laterales (D), y acople

empleando los cuatro tornillos de cabeza redonda de 6 x 25

mm 1; dos tornillos en cada lado. Asegúrese de que el

pedal se extiende en la misma dirección que la pata.

Acople el panel central (B) a los

paneles laterales (D).

EL panel central (B) debe enroscarse a las ménsulas de

los paneles laterales (D) usando los cuatro tornillos de

cabeza redonda de 4 x 25 mm 2 como se muestra en la

ilustración. Asegúrese de que el panel central se monta al

lado de las ménsulas encarado a los pedales.

4 x 25 mm round-head screws 2

4 x 25 mm Halbrundschrauben 2

Vis à tête ronde de 4 x 25 mm 2

Tornillos de cabeza redonda de 4 x 25 mm 2

6 x 25 mm round-head screws 1

6 x 25 mm Halbrundschrauben 1

Vis à tête ronde de 6 x 25 mm 1

Tornillos de cabeza redonda de 6 x 25 mm 1

V Install the main unit (A).

Place the main unit (A) on the side panels (D) with the

screws on its bottom panel (toward the rear of the main

unit) just behind the grooves in the brackets located at the

top of the side panels. Then slide the main unit forward

until it stops. WATCH YOUR FINGERS WHEN DO-

ING THIS!!

Align the holes on the bottom panel of the main unit

with the holes in the brackets on the side panels (also

center the main unit to produce equal clearance on the left

and right sides, as shown in the illustration), then screw in

and securely tighten the four 6 x 16 millimeter flat-head

screws 3.

B Connect the pedal cord.

Pass the pedal cord through the two cord holders on the

side panel. Plug the free end of the cord into the connector

on the bottom of the main unit (A). The plug only goes in

one way (the lug on the connector should face the key-

board-side of the main unit, as shown in the illustration) —

don’t try to force it in the wrong way around.

NSet the adjuster.

For stability, an adjuster is provided on the bottom of

the pedal box (C). Rotate the adjuster until it comes in firm

contact with the floor surface. The adjuster ensures stable

pedal operation and facilitates pedal effect control. If the

adjuster is not in firm contact with the floor surface, dis-

torted sound may result.

IMPORTANT

• After assembling the Clavinova, check once more to

make sure that all screws have been securely fas-

tened.

• If the stand leans to the side, makes unusual noises,

or otherwise seems unstable during use, check and

tighten all screws while following the assembly in-

structions given above.

V Montieren Sie die Tastatureinheit (A).

Setzen Sie die Tastatureinheit (A) so auf den fertigen

Ständer, daß die beiden Schrauben an ihrer Unterseite hinter

den Winkelblechen mit Führungsschlitz an der Hinterseite

des Ständers zu liegen kommen. Schieben Sie die Tastatur-

einheit dann bis zum Anschlag in die Schlitze. KLEMMEN

SIE IHRE FINGER DABEI NICHT EIN!!

Richten Sie die Schraubenbohrungen an der Unterseite der

Tastatureinheit mit den Bohrungen der Winkelbleche aus

(achten Sie auch darauf, daß sie mittig auf dem Ständer steht,

wie in der Abbildung gezeigt). Schrauben Sie die Tastatur-

einheit dann mit den vier 6 x 16 mm Senkschrauben 3 am

Ständer fest.

B Schließen Sie das Pedalkabel an.

Sichern Sie das Pedalkabel in den beiden Kabelhaltern an

den Seitenwänden. Der Stecker wird an die zugehörige

Buchse an der Unterseite der Tastatureinheit (A) angeschlos-

sen. Der Stecker paßt nur in einer Richtung in die Buchse

(mit der Führungsnase zur Tastaturseite des Instruments

weisend — siehe Abbildung). Versuchen Sie nicht, den Stek-

ker falsch herum mit Gewalt in die Buchse zu drücken!

Justieren Sie schließlich noch den

Höhenversteller.

Zur Stabilisierung ist an der Unterseite des Pedalkastens

Höhenversteller heraus, bis er fest auf dem Fußboden steht.

Der Höhenversteller sorgt für stabile Pedalbetätigung und

ermöglicht eine präzise Regelung des Betätigungshubs.

Wenn er nicht fest auf dem Boden steht, können beim Treten

der Pedale Klangverzerrungen auftreten.

WICHTIG

• Vergewissern Sie sich nach Zusammenbau und Auf-

stellung des Clavinova noch einmal davon, daß alle

Schrauben fest angezogen sind.

• Wenn der Ständer schief steht, komische Geräusch

erzeugt oder sich beim Spielen wackelig anfühlt, prüfen

Sie gemäß den unter “Zusammenbau und Aufstellung”

gegebenen Anweisungen, ob der Ständer richtig

zusammengebaut wurde, und ziehen dabei die einzel-

nen Schrauben noch einmal nach.

iii

6 x 16 mm flat-head screws 3

6 x 16 mm Senkschrauben 3

Vis à tête plate de 6 x 16 mm 3

Tornillos de cabeza plana de 6 x 16 mm 3

5 6

V Posez le clavier (A)

Placez le clavier sur les panneaux latéraux (D), avec les

vis de son panneau inférieur (situées vers l’arrière du cla-

vier) placées immédiatement derrière les rainures des fer-

rures situées à la partie supérieure des panneaux latéraux

(D), puis faites glisser le clavier vers l’avant jusqu’à ce

qu’il vienne en butée. FAITES ATTENTION A VOS

DOIGTS EN EXECUTANT CETTE OPERATION!!

Alignez les trous du panneau inférieur du clavier sur les

trous des ferrures des panneaux latéraux (centrez égale-

ment le clavier de manière à avoir un jeu identique de cha-

que côté) puis posez et serrez à fond les quatre vis à tête

plate de 6 x 16 millimètres 3.

B Connectez le cordon du pédalier

Faites passer le cordon du pédalier dans les deux sup-

ports de cordon situés sur le panneau latéral. La prise doit

être branchée au connecteur correspondant situé à la partie

inférieure du clavier (A). La prise ne peut être branchée

que dans un seul sens (la languette de la prise doit être

dirigée vers l’avant du clavier, comme montré sur l’illus-

tration) et n’essayez donc pas de la forcer pour la mettre en

place du mauvais côté.

N’oubliez pas de régler la hauteur du

pédalier

Pour assurer la stabilité du pédalier (C), un dispositif de

réglage a été prévu à sa partie inférieure. Tournez ce dis-

positif jusqu’à ce qu’il soit en contact ferme avec la sur-

face du sol. Ce dispositif assure la stabilité du pédalier

lors de son utilisation et facilite la commande au pied des

effets. Si ce dispositif n’est pas en contact ferme avec le

sol, il pourra se produire une distorsion du son.

IMPORTANT

• Après avoir assemblé le Clavinova, vérifiez une fois

de plus que toutes les vis sont bien serrées.

• Si le support du clavier penche d’un côté, fait du bruit

ou semble instable lorsque vous utilisez l’instrument,

vérifiez de nouveau et resserrez toutes les vis en

suivant les instructions d’assemblage données ci-

dessus.

V Instale la unidad principal (A).

Coloque la unidad principal en los paneles laterales (D)

con los tornillos de su panel inferior (hacia la parte poste-

rior de la unidad principal) justo detrás de las ranuras de la

ménsula ubicada en la parte superior de los paneles latera-

les (D), después deslice el teclado hacia adelante hasta que

se pare. ¡TENGA CUIDADO CON SUS DEDOS MIEN-

TRAS LO HACE!

Alinee los orificios del panel inferior de la unidad prin-

cipal con los orificios de las ménsulas de los paneles late-

rales (también centre la unidad principal para producir una

holgura igual en los lados derecho e izquierdo, como se

muestra en la ilustración), después enrosque y apriete bien

los cuatro tornillos de cabeza plana de 6 x 16 mm 3.

B Conecte el cable de los pedales.

Pase el cable de los pedales a través de los dos soportes

de cable del panel lateral. La clavija puede enchufarse en

el conector correspondiente de la parte inferior de la uni-

dad principal (A). La clavija se enchufa sólo en una direc-

ción (la lengüeta del conector debe estar encarada hacia el

lado del teclado de la unidad principal, como se muestra en

la ilustración), por eso no la fuerce en la dirección errónea.

NAsegúrese de ajustar el ajustador.

Para la estabilidad del aparato, se proporciona un

ajustador en la parte inferior de la caja de pedales (C).

Gire el ajustador hasta que contacte firmemente con el

suelo. El ajustador asegura una operación estable de los

pedales y facilita el control del efecto de los pedales. Si el

ajustador no contacta firmemente con el suelo, puede re-

sultar en sonido distorsionado.

IMPORTANTE

• Después de montar la Clavinova, compruebe otra

vez para asegurarse de que todos los tornillos se

han apretado bien.

• Si el soporte se inclina hacia un lado, hace ruidos

anormales, o parece inestable durante la utilización,

compruebe y apriete todos los tornillos mientras

sigue las instrucciones de montaje de arriba.

Cord holder

Kabelhalter

Support de cordon

Soporte del cable

Si vous êtes très familier avec l’interface MIDI ou si vous utilisez un

ordinateur pour commander votre matériel de musique au moyen de

messages MIDI générés par ordinateur, les données suivantes vous

seront utiles et vous aideront à commander le Clavinova.

SI usted está ya familiarizado con MIDI, o si emplea una

computadora para controlar sus aparatos musicales con mensajes MIDI

generados por computadora, los datos proporcionados en esta sección

le ayudarán a controlar la Clavinova.

1. NOTE ON/OFF

Data format: [9nH] -> [kk] -> [vv]

9nH = Note ON/OFF event (n = channel number)

kk = Note number

Transmit: 15 ~ 114 = D#-1 ~ F#7

Receive: 21 ~ 108 = A-1 ~ C7

vv = Velocity (Key ON = 1 ~ 127. Key OFF = 0)

Data format: [8nH] -> [kk] -> [vv]

8nH = Note OFF event (n = channel number)

kk = Note number

Transmit: 15 ~ 114 = D#-1 ~ F#7

Receive: 21 ~ 108 = A-1 ~ C7

vv = Velocity (Key OFF = 0 ~ 127)

* 8nH (note off) is receive only.

* 9nH (vv=00H) used for transmission.

2. CONTROL CHANGE & MODE MESSAGES

Data format: [BnH] -> [cc] -> [vv]

BnH = Control event (n = channel number)

cc = Control number

vv = Control value

CONTROL

VALUE [vv]

07H Volume 00000000 : -∞

(reception only) 01101111 : -3dB

01111111 : ±0dB

0AH Pan Pot 00H ~ 17H LEFT 6

(reception only) 18H ~ 1FH 5

20H ~ 27H 4

28H ~ 2FH 3

30H ~ 37H 2

38H ~ 3FH 1

40H ~ 47H CENTER

48H ~ 4FH SCALING PAN

50H ~ 57H RIGHT 1

58H ~ 5FH 2

60H ~ 67H 3

68H ~ 6FH 4

70H ~ 77H 5

78H ~ 7FH 6

0BH Expression 00000000 : -∞

(reception only) 01101111 : -3dB

01111111 : ±0dB

40H Damper 00H ~ 3FH : OFF

Pedal 40H ~ 7FH : ON

42H Sostenuto 00H ~ 3FH : OFF

Pedal 40H ~ 7FH : ON

43H Soft Pedal 00H ~ 3FH : OFF

40H ~ 7FH: ON

5BH Reverb Depth 00H ~ 7FH : ON

(Sixteen levels)

78H

All Sound OFF (reception only)

00H

79H

Reset All Controller (reception only)

00H

7AH Local Control ON/OFF 00H : OFF

(reception only) 7FH : ON

7BH All Notes OFF (reception only) 00H

7CH Omni OFF/All Notes OFF 00H

(reception only)

7DH Omni ON/All Notes OFF 00H

(reception only)

3. PROGRAM CHANGE

Data format: [CnH] -> [pp]

CnH = program event (n = channel number)

pp = Program number

pp VOICE NAME pp VOICE NAME

00 PIANO 03 HARPSICHORD

01 CLAVINOVA TONE 04 ORGAN

02 E. PIANO

4. SYSTEM REALTIME MESSAGES

[rrH]

F8H: Timing clock

FAH: Start

FCH: Stop

FEH: Active sensing

Data Transmission Reception

F8H Transmitted every Received as 96-clock

96 clocks tempo timing when

MIDI clock is set to

External

FAH Recorder start Recorder start

FCH Recorder stop Recorder stop

FEH Transmitted every All notes are turned

200 milliseconds off if no data is

received for more than

400 milliseconds

Caution: If an overrun framing error occurs the

Damper, Sostenuto, and Soft effects for all chan-

nels are turned off and an All Note Off occurs.

If you’re already very familiar with MIDI, or are using a computer to

control your music hardware with computer-generated MIDI mes-

sages, the data provided in this section can help you to control the

Clavinova.

Falls Sie bereits mit MIDI vertraut sind oder einen Computer zur

Erzeugung von MIDI-Steuermeldungen für die Instrumente

verwenden, können Sie sich zur Steuerung des Clavinovas nach den

im folgenden Abschnitt aufgeführten Spezifikationen richten.

MIDI Data Format/MIDI-Datenformat/Format des données MIDI/Formato de datos MIDI

02H :

Dual On (Left voice 1 octave up)

03H :

Dual On (Right voice 1 octave up)

5CH Dual Voice [vv] : Dual Voice

* When cc=59 (Reverb), Clavinova common ID (01H)

is recognized in addition to 38H.

(4) Absolute Tempo

Data format: [F0H] -> [43H] -> [73H] -> [xx]

-> [11H] -> [1nH] -> [cc] -> [dd] -> [F7H]

43H : Yamaha ID

73H : Clavinova ID

xx : 38H (CLP-153SG ID)

11H : Clavinova special control

1nH : Control MIDI change

(Transmit: n=control channel number)

(Receive: any channel OK)

ccH : Absolute tempo low byte

ddH : Absolute tempo hight byte

Tempo=dd*128+cc

PANEL DATA SEND FORMAT

F0H, 43H, 0nH, 7CH, 00H, 1BH (n: channel number)

53H, 4BH, 20H, 20H (SK)

43H, 4CH, 50H, 27H, 39H, 34H (CLP ’94)

3xH, 3yH (x, y: version number)

[PANEL DATA]

[CHECK SUM (1byte)] =

0-(53H+4BH+20H+...+Data end)

F7H

• Panel Data Contents

(1) VOICE

(2) DUAL VOICE

(3) DUAL ON/OFF

(4) DUAL BALANCE

(5) 0

(6) 0

(7) 0

(8) REVERB NUMBER

(9) REVERB DEPTH

(10) TOUCH SENSITIVITY

(11) LEFT PEDAL (SOFT or SOSTENUTO)

(12) SPLIT POINT

(13) 0

(14) Absolute tempo low byte

(15) Absolute tempo high byte

NAME DATA SEND FORMAT

F0H, 43H, 0nH, 7DH, 00H, 10H (n: channel number)

53H, 4BH, 20H, 20H (SK)

43H, 4CH, 50H, 27H, 39H, 34H (CLP ’94)

3xH, 3yH, 20H, 20H, 20H, 20H (x, y: version number)

[CHECK SUM (1byte)] = 0-(53H+4BH+20H+......+20H)

F7H

BULK DUMP FORMAT

F0H, 43H, 73H

38H

(Product ID: CLP-153SG)

06H (Bulk ID)

02H (Bulk number)

0DH, 00H, 07H, 0CH

(Data length= wxyzH 0x683e*2 bytes)

[BULK DATA] (Sequence data)

[CHECK SUM (1byte)] = 0-sum (BULK DATA)

F7H

5. SYSTEM EXCLUSIVE MESSAGES

(1) YAMAHA MIDI Format

Data format: [F0H] -> [43H] -> [xn] -> [ff] ... [F7H]

43H : Yamaha

xn : Substatus + channel number.

ff : Format number.

xff Information

0 7CH

Panel Data receive.

2 7CH

Panel Data Send occurs when this data received.

2 7DH

Name Data Send occurs when this data received.

(2) Clavinova MIDI Format

Data format: [F0H] -> [43H] -> [73H] -> [xx]

-> [yy] -> [F7H]

43H : Yamaha ID

73H : Clavinova ID

xx : 38H (CLP-153SG ID)

yy : Substatus

yy Information

02H Internal MIDI clock.

03H External MIDI clock.

13H Multi-timbre mode OFF.

14H

Clavinova Common Voice multi-timbre mode ON.

15H Multi-timbre mode ON.

61H MIDI FA cancel ON.

62H MIDI FA cancel OFF.

7cH

All notes OFF; receive channel = c+1; omni OFF.

* When yy=2, 3, 13, 14, 15 or 7c, Clavinova com-

mon ID (01H) is recognized as well as 38H.

All Control Change values are reset when [13H],

[14H] or [15H] is received. All voices and other

parameters are also reset when [14H] or [15H] is

received in order to ensure the same initial settings.

(3) Special Control

Data format: [F0H] -> [43H] -> [73H] -> [xx]

-> [11H] -> [0nH] -> [cc] -> [vv] -> [F7H]

43H : Yamaha ID

73H : Clavinova ID

xx : 38H (CLP-153SG ID)

11H : Clavinova special control

0nH : Control MIDI change + channel number

cc : Control number

vv : Value

cc Control Value [vv]

08H

Dual Balance

00H : Left Voice Max.

7FH : Right Voice Max.

1BH Metronome 00H : Off

01H : On

26H Touch 00H : Medium

Sensitivity 01H : Soft

02H : Hard

03H : Off

59H Reverb 00H : Off

01H : Room

02H : Hall-1

03H : Hall-2

04H : Cosmic

5AH Dual Mode 00H : Dual Off

01H : Dual On (Normal)

Specifications/Technische Daten/

Caractéristiques techniques/Especificaciones

CLP-153SG

KEYBOARD 88 KEYS (A-1 ~ C7)

POLYPHONY 16 NOTES

VOICE SELECTORS PIANO, CLAVINOVA TONE, E. PIANO, HARPSHOCHORD, ORGAN

REVERB ROOM, HALL 1, HALL 2, COSMIC

TOUCH SENSITIVITY HARD, MEDIUM, SOFT, FIXED

RECORDER PLAY, REC

PEDAL CONTROLS SOFT/SOSTENUTO, DAMPER

OTHER CONTROLS MASTER VOLUME, TEMPO, METRONOME, DEMO, MIDI/TRANSPOSE

JACKS/CONNECTORS PHONES x 2, AUX OUT R & L/L+R, AUX IN R & L, MIDI IN/OUT

INPUT & OUTPUT AUX OUT: Output impedance 600 Ω

LEVEL/IMPEDANCE AUX IN: Input impedance 10 kΩ/Input sensitivity -10 dBm

MAIN AMPLIFIERS 20W x 2

SPEAKERS 16 cm x 2

DIMENTIONS

(W x D x H) Music stand down:

1375 x 471.4 x 830.4 mm (54-1/8" x 18-1/2" x 32-3/4")

Music stand up:

1375 x 471.4 x 1007.5 mm (54-1/8" x 18-1/2" x 39-5/8")

WEIGHT 54.0 kg (119.0 lbs.)

Specifications subject to change without notice.

Änderungen ohne Vorankündigung vorbehalten.

* Sous toute réserve de modification des caractéristiques sans préavis.

* Especificaciones sujetas a cambios sin previo aviso.

MIDI Implementation Chart

Not available

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted

by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio

frequencies and, if not installed and used according to the instruc-

tions found in the users manual, may cause interference harmful

to the operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not occur in

all installations. If this product is found to be the source of inter-

ference, which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker

or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the an-

tenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic Service Divi-

sion, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

VT68500 507POCP2.301-A0 Printed in Japan

CANADA

THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B”

LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARA-

TUS SET OUT IN THE RADIO INTERFERENCE REGULATION OF

THE CANADIAN DEPARTMENT OF COMMUNICATIONS.

LE PRESENT APPAREIL NUMERIQUE N’EMET PAS DE BRUITS

RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES

AUX APPAREILS NUMERIQUES DE LA “CLASSE B” PRESCRITES

DANS LE REGLEMENT SUR LE BROUILLAGE RADIOELECTRI-

QUE EDICTE PAR LE MINISTERE DES COMMUNICATIONS DU

CANADA.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU

FOND.

• This applies only to products distributed by Yamaha Canada Music Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in accor-

dance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured makings identifying the terminals

in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the termi-

nal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal of

the three pin plug.

Yamaha CLP-153SG El manual del propietario

Marca: Yamaha

Modelo: CLP-153SG

Categoría: Sintetizador

Tipo: El manual del propietario

Descargar PDF

informe

en otros idiomas

français: Yamaha CLP-153SG Le manuel du propriétaire
italiano: Yamaha CLP-153SG Manuale del proprietario
English: Yamaha CLP-153SG Owner's manual
Deutsch: Yamaha CLP-153SG Bedienungsanleitung
русский: Yamaha CLP-153SG Инструкция по применению
Nederlands: Yamaha CLP-153SG de handleiding
português: Yamaha CLP-153SG Manual do proprietário
dansk: Yamaha CLP-153SG Brugervejledning
polski: Yamaha CLP-153SG Instrukcja obsługi
čeština: Yamaha CLP-153SG Návod k obsluze
svenska: Yamaha CLP-153SG Bruksanvisning
Türkçe: Yamaha CLP-153SG El kitabı
suomi: Yamaha CLP-153SG Omistajan opas
română: Yamaha CLP-153SG Manualul proprietarului

Otros documentos

Dell PowerEdge C6220 II El manual del propietario

Yamaha CLP-153SG El manual del propietario

Yamaha CLP-153SG El manual del propietario

en otros idiomas

Artículos relacionados

Otros documentos