Transcripción de documentos

RX-10 Natural Sound Stereo Receiver Ampli-syntoniseur stéréo de la série “Natural Sound” Natural Sound Stereoreceiver Natural Sound Stereoreceiver Ricevitore stereo a suono naturale Receptor estéreo de Sonido Natural Natural Sound Stereo Ontvanger OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING  SUPPLIED ACCESSORIES ACCESSOIRES FOURNIS MITGELIEFERTES ZUBEHOR MEDFOLJANDE TILLBEHOR ACCESSORI IN DOTAZIONE ACCESORIOS INCLUIDOS BIJGELEVERDE ACCESSOIRES ● ● ● ● ● ● ● Remote Control Transmitter Emetteur de télécommande Fernbedienungsgeber Fjärrkontrollsändare Telecomando Transmisor del control remoto Afstandbediening ● ● ● ● ● ● ● After unpacking, check that the following parts are contained. Après le déballage, vérifier que les pièces suivantes sont incluses. Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind. Kontrollera efter det apparaten packats upp att följande delar finns med. Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio. Desembale el aparato y verificar que los siguientes accesorios están en la caja. Controleer na het uitpakken of de volgende onderdelen voorhanden zijn. ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Indoor FM Antenna Antenne FM intérieure UKW-Innenantenne FM inomhusantenn Antenna FM per interni Antena FM interior FM Binnenantenne AM Loop Antenna Antenne AM à boucle MW-Rahmenantenne AM ramantenn Antenna AM ad anello Antena de cuadro de AM AM Lusantenne Batteries (size AA, R6, UM-3) Piles (taille AA, R6, UM-3) Batterien (Größe AA, R6, UM-3) Batterier (storlek AA, R6, UM-3) Batterie (dimensioni AA, R6, UM-3) Pilas (tamaño AA, R6, UM-3) Batterijen (maat AA, R6, UM-3) This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or 87/308/EEC. Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE. Diese Geräte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG. Dette apparat overholder det gaeldende EF-direktiv vedrørende radiostøj. Questo apparecchio è conforme al D.M.13 aprile 1989 (Direttiva CEE/87/308) sulla soppressione dei radiodisturbi. Este producto está de acuerdo con los requisitos sobre interferencias de radio frecuencia fijados por el Consejo Directivo 87/308 CEE. Dit product voldoet aan de EEG normen betreffende radio-frekwentie storingen 82/499/EEG en/of 87/308/EEG. 2  FEATURES ● 50W + 50W (8Ω) RMS Output Power, 0.03% THD, 20 – 20,000 Hz ● IF Count Direct PLL Synthesizer Tuning System ● High Dynamic Power, Low Impedance Drive Capability ● Pure Direct Switch to Reproduce the Purest Source Sound ● Continuously Variable Loudness Control ● Remote Control Capability ● 40-Station Random Preset Tuning <U.K. and Europe models only> ● Automatic Preset Tuning ● Preset Station Shifting Capability (Preset Editing) ● English Thank you for selecting this YAMAHA stereo receiver. Multi-Functions for RDS Broadcast Reception CONTENTS Supplied Accessories ......................................2 Caution ............................................................4 Connections ....................................................5 Receiving RDS Stations (U.K. and Europe models only) ......................15 Remote Control Transmitter ..........................19 Basic Operations .............................................8 Notes about the Remote Control Transmitter ....................................................20 Tuning Operations .........................................11 Troubleshooting .............................................21 Preset tuning .................................................12 Specifications ................................................22 3  CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water. 3. Never open the cabinet. If something drops into the set, contact your dealer. 4. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves. 5. The openings on the cabinet assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the cabinet will rise rapidly. It may not only damage the unit, but also cause fire. Therefore, avoid placing objects against these openings, and install the unit where the flow of air through the ventilation openings could not be impeded, allowing a space of at least 10 cm above the top panel of the unit. IMPORTANT Please record the serial number of this unit in the space below. Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS unit TO RAIN OR MOISTURE. The apparatus is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the apparatus itself is turned off. For U.K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. 6. Always set the VOLUME control to “0” before starting the audio source play. Increase the volume gradually to an appropriate level after playback has been started. 7. Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. 8. Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. IMPORTANT: The wire in the mains lead are coloured in accordance with the following code: 9. When not planning to use this unit for long periods of time (ie., vacation, etc.), disconnect the AC power plug from the wall outlet. Blue: NEUTRAL Brown: LIVE 10. To prevent lightning damage, disconnect the AC power plug and disconnect the antenna cable when there is an electrical storm. 11. Grounding or polarization – Precautions should be taken so that the grounding or polarization of an appliance is not defeated. 12. AC outlet Do not connect audio equipment to the AC outlet on the rear panel if that equipment requires more power than the outlet is rated to provide. SPECIAL INSTRUCTIONS FOR U.K. MODEL The colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug. Proceed as follows: the wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. 13. Voltage Selector (General Model only) The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240V AC, 50/60 Hz. 4 FREQUENCY STEP switch (General Model only) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.  English CONNECTIONS ANTENNA CONNECTIONS ● ● Each antenna should be connected to the designated terminals correctly, referring to the following figure. Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. Outdoor FM antenna Indoor FM antenna (included) 300-ohm feeder 75 UNBAL. 75-ohm coaxial cable FM ANT 75-ohm/300-ohm antenna adapter AM loop antenna (included) GND AM ANT TAPE Outdoor AM antenna Ground Connecting the AM loop antenna ➀ ➂ Orient so that the best reception is obtained. ➁ * The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit. GND terminal For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. Notes When connecting the indoor FM antenna, insert its connector into the FM ANT terminal firmly. ● If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, coaxial cable is preferable. ● 5  Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made. AUDIO CONNECTIONS When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit. * For a system connection with YAMAHA CDX-10 and KX-10 (or KX-W10), connections can be made easily by making sure to connect the output (or input) terminals of each component to the same-numbered terminals of this unit. Turntable OUTPUT GND GND AUDIO SIGNAL FM ANT 75 UNBAL. Video cassette player, LD player, etc. PHONO OUTPUT 1 GND CD Compact disc player AM ANT AUX Tape deck 2 LINE OUT 3 3 or 5 TAPE PB LINE IN 4 4 or 6 REC OUT LINE OUT TAPE 2 TAPE 1 LINE IN Tape deck 1 CONNECTING SPEAKERS Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut to be as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass. Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit and/or speakers. ● ● One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals. Use speakers with the specified impedance shown on the rear of this unit. Speakers A Right Left (General model) GND SPEAKERS SWITCHED 100W MAX. TOTAL A B A + B:l2ΩMIN. /SPEAKER A OR B: 6ΩMIN. /SPEAKER Left Right 6 Speakers B * : Refer to “ABOUT THE ACCESSORY TERMINALS” on page 7.  <General model only> Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal. Red: positive (+) Black: negative (–) 2 1 3 English How to Connect: ➀ Unscrew the knob. ➁ Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.] ➂ Tighten the knob and secure the wire. ABOUT THE ACCESSORY TERMINALS AC OUTLET(S) (SWITCHED) GND terminal (For turntable use) (Europe and General models)...........2 SWITCHED OUTLETS (U.K. model) ........................................1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit’s POWER switch or the provided remote control transmitter’s POWER key. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLET(S) is 100 watts. Connecting the ground wire of the turntable to this terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected. GND 7  BASIC OPERATIONS <U.K. and Europe models> <General model> 3 1, 6 2 4 3 1, 6 2 4 7 7 To play a source 1 4 VOLUME Select the speakers to be used. SPEAKERS A ON OFF B 0 l0 * If you use two speaker systems, press both the A and B switches. Set to the “0” position. 2 Turn the power on. Power indicator 5 Play the source. (For detailed information on the tuning operations, refer to the page 11.) POWER PURE DIRECT 3 Lights up. 6 VOLUME Select a desired input source. INPUT 0 AUX/TAPE 2/TAPE 1/CD/TUNER/PHONO l0 Adjust to the desired output level. 7 * The name of the selected input source will appear on the display. To turn off the power Press the POWER switch again. 8 If desired, adjust the BASS, TREBLE, BALANCE controls and PURE DIRECT switch. (Refer to page 10.) Note When listening to a source sound, make sure that “TAPE MONITOR 2” is not illuminated on the display. If it is illuminated, press the TAPE 2 MONITOR button to turn it off.  English <U.K. and Europe models> <General model> 1 1 2 2 4 4 To record a source to tape (or dub from tape to tape) * It is recommended to use the tape deck 2 as a recording tapedeck. 1 Select the source to be recorded. 3 Begin recording on the tape deck. INPUT AUX/TAPE 2/TAPE 1/CD/TUNER/PHONO 4 2 Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on the tuning operations, refer to the page 11.) If the tape deck 2 is used for recording, you can monitor the sound being recorded (or to be recorded) by pressing the TAPE 2 MONITOR button so that “TAPE MONITOR 2” lights up on the display. TAPE 2 MONITOR TAPE MONITOR 12 VOLUME Note VOLUME, BASS, TREBLE and BALANCE controls and PURE DIRECT switch settings have no effect on the material being recorded. 0 l0 When you listen with headphones Connect the headphones to the PHONES jack. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position. PHONES 9  Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused from speaker location or listening room conditions. Selecting the SPEAKER system Because one or two speaker systems can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B, or both at once. BALANCE SPEAKERS A ON OFF B L R Adjusting the BASS and TREBLE controls BASS TREBLE 0 0 – BASS + – + Using PURE DIRECT switch You can enjoy the purest possible sound from your audio sources by pressing this switch so that the PURE DIRECT indicator lights up. By doing so, the audio signal bypasses the BASS, TREBLE and BALANCE controls, eliminating any alterations to the audio signal. PURE DIRECT : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. PURE DIRECT TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. Open/close the control door To open the door To close the door When it is not necessary to operate controls inside the control door, close the door. 10  Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). <U.K. and Europe models> <General model> 21 4 3 21 43 AUTOMATIC TUNING 1 MANUAL TUNING Select the reception band (FM or AM) while watching the display. 1 FM/AM Select the reception band (FM or AM) while watching the display. FM/AM or FM 2 AM 2 TUNING MODE TUNING MODE If “PRESET” is illuminated on the display, press the KEY MODE button to turn it off. <U.K. and Europe models> –– PS/PTY/SEEK –– 3 “AUTO TUNING” goes off. KEY MODE PRESET STATIONS UP FREQ/PS/PTY TUNING To tune to a higher frequency, press the right side once. To tune to a lower frequency, press the left side once. * If the station where tuning search stopped is not the desired one, press again. * If the tuning search does not stop at the desired station (because the signals of the station are weak), change to the MANUAL TUNING method. 1 MHz 0 20 l00 3 KEY MODE ENTER SHIFT/EDIT ENTER/KEY MODE Tune to a desired station manually. PRESET STATIONS DOWN UP TUNING * To continue tuning search, press and hold the button. Note If you tune to an FM station manually, it is received in monaural mode automatically to increase the signal quality. 2 STEREO FM 4 ➀ Display information <General model> –– PS/PTY/SEEK –– SHIFT/EDIT ENTER/KEY MODE DOWN If “PRESET” is illuminated on the display, press the KEY MODE button to turn it off. <U.K. and Europe models> <General model> ENTER 4 AM AUTO/ MAN'L MONO AUTO/ MAN'L MONO FREQ/PS/PTY or FM AUTO TUNING 3 English TUNING OPERATIONS ➁ ➂ Displays the band and frequency of the received station. * <U.K. and Europe models only> If an RDS station is received, the frequency is then replaced by the station name. (However, if the PS data cannot be received within 5 seconds, “NO PS” flashes, and then it returns to the frequency display.) Refer to page 16 for details. Lights up when an FM stereo broadcast is received in stereo. Indicates the signal level of the received station. 11  PRESET TUNING MANUAL PRESET TUNING This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 pages) can be stored. <U.K. and Europe models> <General model> 3, 1 2, 5 3, 1 2 4, 3 2, 5 To store stations 1 2 4, 3 To recall a preset station 1 Tune to a desired station. (Refer to the previous page for tuning procedures.) Select the page where the preset station is stored. A/B/C/D/E PRESET 2 FM MEMORY MEMORY PRESET FM MEMORY 2 MAN'L/AUTO FM Flashes on and off for about 5 seconds. 3 Select a desired page (A – E) of preset stations while watching the display. If “PRESET” is not illuminated on the display, you cannot recall the preset stations. Press the KEY MODE button to turn it on. <U.K. and Europe models> <General model> KEY MODE –– PS/PTY/SEEK –– A/B/C/D/E PRESET ENTER FREQ/PS/PTY FM SHIFT/EDIT ENTER/KEY MODE MEMORY 4 Select a preset station number (1–8) while watching the display before “MEMORY” goes off from the display. PRESET STATIONS DOWN 3 PRESET STATIONS DOWN TUNING UP UP Select the preset station number. TUNING 5 PRESET MEMORY STEREO FM MHz 0 20 l00 Notes ● A new setting can be programmed in place of the former one. ● For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency. AUTO TUNING MAN'L/AUTO FM Shows the displayed station has been programmed to A1. * In the same way, program other stations to A2, A3 ... A8. * You can program more stations on other pages in the same way by selecting other pages in step 3. 12 Memory back-up The memory back-up circuit prevents the programmed data from being lost even if the POWER switch is set off or the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simply following the PRESET TUNING steps.  You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 12. <U.K. and Europe models only> Only RDS stations can be stored by this function. <U.K. and Europe models> English AUTOMATIC PRESET TUNING <General model> 1 1 3 2 2 3 To store stations 1 When the automatic preset tuning is finished FM/AM FM The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure of the section “To recall a preset station” on page 12. To recall a preset station 2 MEMORY Press and hold for about 3 seconds. MAN'L/AUTO FM Simply follow the procedure of the section “To recall a preset station” on page 12. <U.K. and Europe models only> * A recalled station is shown by the frequency or station name on the display. PRESET AUTO TUNING MEMORY and Flashes. 3 <U.K. and Europe models> –– PS/PTY/SEEK –– FREQ/PS/PTY SHIFT/EDIT ENTER/KEY MODE Flashes. <General model> KEY MODE ENTER The automatic preset tuning begins from A1. Received stations are programmed to A1, A2 ... A8 sequentially. * If more than 8 stations are received, they are also programmed to the preset station numbers on other pages (B, C, D and E) in that order. If you want to store the first station received by the automatic preset tuning to a desired preset station number. If, for example, you want to store the received first station to C5, select “C5” by using the A/B/C/D/E button and the PRESET STATIONS button soon after the display begins flashing on/off in step 2. By pressing ENTER button, the automatic preset tuning begins. The received first station is stored to C5, and next stations to C6, C7 ... sequentially. If stations are stored up to E8, the automatic preset tuning is finished automatically. Notes ● You can replace a preset station by another FM or AM station manually by simply following the procedure of the section “To store stations” on page 12. <General model only> ● If the number of received stations is not enough to be stored up to E8, the search is finished automatically when it reaches the highest frequency after searching through all frequencies. ● With this function, only FM stations with sufficient signal strength are stored automatically. If the station you want to program is week in signal strength, tune to it in monaural manually and program it by following the procedure of the section “To store stations” on page 12. <U.K. and Europe models only> ● The automatic preset tuning search will be performed through all RDS network frequencies until stations are stored up to E8. If the number of received stations is not enough to be stored up to E8, the search is finished automatically after searching through all frequencies. ● With this function, only RDS stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune to it in monaural manually and program it by following the procedure of the section “To store stations” on page 12. * There may be a case that this function cannot receive a station which could be received by the automatic tuning method. This is because this function receives a large volume of PI (Program Identification) data along with the station. 13  EXCHANGING PRESET STATIONS You can exchange the places of two preset stations with each other as shown below. <U.K. and Europe models> <General model> 2, 4 2, 4 Example) If you want to shift the preset station on E1 to A5, and vice versa. 1 Recall the preset station on E1 (by following the method of “To recall a preset station” on page 12). 2 <U.K. and Europe models> –– PS/PTY/SEEK –– FREQ/PS/PTY 4 <U.K. and Europe models> <General models> –– PS/PTY/SEEK –– EDIT <General models> EDIT FREQ/PS/PTY SHIFT/EDIT ENTER/KEY MODE SHIFT/EDIT ENTER/KEY MODE Press and hold for about 3 seconds. Shows the exchange of stations is completed. Flashes 3 14 Next, recall the preset station on A5 by following the same method with step 1.  English RECEIVING RDS STATIONS <U.K. and Europe models only> RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations using this system transmit an inaudible stream of data in addition to the normal radio signal. RDS data contains various information, such as AF (Alternative Frequencies for the same program station), PI (Program Identification), PS (Program Service station name), PTY (Program Type name), etc. RDS function is carried out among the network stations. * This unit utilizes PI, PS and PTY to receive RDS broadcast stations. Displaying RDS data This unit can be turned into the following two modes to display RDS data. PS (Program Service station name) mode: Displays the name of the RDS station now being received instead of the frequency. BBC R3 PTY (Program Type name) mode: Displays the program type of the RDS station now being received. There are 15 program types to classify RDS stations as follows. NEWS AFFAIRS INFO SPORT EDUCATE DRAMA News: Short accounts of facts, events and publicly expressed views, reportage and actuality. Current affairs: Topical program expanding or enlarging upon the news, generally in different presentation style or concept, including documentary debate, or analysis Information: Program whose purpose is to impart advice in the widest sense, including meteorological reports and forecasts, consumer affairs, medical help, etc. VARIED POP M ROCK M Sport: Program concerned with any aspect of sport. M.O.R. M Education: Program intended primarily to educate, of which the formal element is fundamental. Varied: Used for mainly speech-based programs usually of light-entertainment nature, not covered by above categories. Examples are: quizzes, panel games, personality interviews, comedy and satire. Pop: Commercial music, which would generally be considered to be of current popular appeal, often featuring in current or recent record sales charts. Rock: Contemporary modern music, usually written and performed by young musicians. M.O.R.: (Middle of the Road Music). Common term to describe music considered to be “easylistening”, as opposed to Pop, Rock or Classical. Music in this category is often but not always, vocal, and usually of short duration (<5 min.) Light classics: Classical Musical for general, rather than specialist appreciation. Examples of music in this category are instrumental music, and vocal or choral works. Drama: All radio plays and serials. LIGHT M Culture: Programs concerned with any aspect of national or regional culture, including religious affairs, philosophy, social science, language, theatre, etc. CLASSICS Performances of major orchestral works, Serious classics: CULTURE SCIENCE Science: Programs about the natural sciences and technology. symphonies, chamber music etc., and including Grand Opera. OTHER M Other music: Musical styles not fitting into any of the above categories. Particularly used for specialist music, of which Jazz, Rhythm & Blues, Folk, Country, and Reggae are examples. 15  To turn the unit into the PS mode or PTY mode Press the FREQ/PS/PTY button. Whenever pressed, the mode changes into the PS mode, PTY mode and returns to usual mode in turn. * When an RDS station is received, the display is automatically turned into the PS mode. Do not press the FREQ/PS/PTY button until the display is turned into the PS mode. If the button is pressed before the display mode is changed, it may occur that “NO PS” flashes on the display. This is because the unit has not received all of the RDS data on the station yet. –– PS/PTY/SEEK –– FREQ/PS/PTY PS mode The name of the station being received is displayed. If the station is not an RDS station, “NO PS” flashes on the display and then returns to usual mode. PTY mode A program type for the station being received is displayed. If the RDS station does not employ the PTY data service, “NO PTY” flashes on the display and then returns to the usual mode. If the station is not an RDS station, “NO PTY” flashes on the display and then returns to usual mode. Usual mode The frequency of the station being received is displayed. SHIFT/EDIT ENTER/KEY MODE Note When PS or PTY data reception is not possible due to poor reception conditions, “NO PS” or “NO PTY” flashes on the display in each mode. In such a case, press the TUNING MODE button so that “AUTO TUNING” goes off from the display. Though the reception mode is changed to monaural by this operation, when you changes to the PS or PTY mode, PS or PTY data may be displayed. 16  English Calling a preset RDS station by the station name (PS SEEK) You can call a desired RDS station stored in this unit by only inputting the name of the station in the PS mode. By this operation, this unit searches all preset stations for the station. You do not have to input a full name, even only the first letter can be used for calling. As many as 8 letters and/or numerals can be selected for inputting a name. 1 4, 8 2 3, 5 7 FM/AM 1 2 FM 7 Turn the unit into the PS mode. –– PS/PTY/SEEK –– FREQ/PS/PTY SHIFT/EDIT ENTER/KEY MODE 6 A station name is displayed or “NO PS” flashes. Repeat steps 4 and 5 for other letters and/or numerals, if necessary. When inputting the name is finished, press the ENTER/KEY MODE button. –– PS/PTY/SEEK –– ET ENTER FREQ/PS/PTY * If “NO PS” flashes, proceed to the next step while flashing. If “NO PS” disappears before you proceed to the next step, press the FREQ/PS/PTY button again. Flashes. 8 3 SHIFT/EDIT ENTER/KEY MODE PRESET STATIONS DOWN UP Press once. –– PS/PTY/SEEK –– TUNING FREQ/PS/PTY SHIFT/EDIT ENTER/KEY MODE Flashes. 4 Select the first letter or numeral of the station name. PRESET STATIONS DOWN The unit begins searching for the station, and it is continued until the station is found. You do not have to input a full name for searching for the station UP TUNING * By pressing the PRESET STATIONS button repeatedly or by pressing and holding it, the display will change letters and numerals in sequence. * If you will not input the second letter, skip to step 7. You may input only the first letter of the station name. If doing so, you can skip steps 5 and 6. In step 8, the unit searches for and calls a nearest station which has the letter you input. If the station is not the desired one, press the PRESET STATIONS button again. The unit will begin searching for another station which has the same letter. To cancel this function 5 When the first letter or numeral of the station name appears, press the SHIFT/EDIT button to proceed to the selection of the next letter or numeral. –– PS/PTY/SEEK –– FREQ/PS/PTY SHIFT/EDIT ENTER/KEY MODE Press the FREQ/PS/PTY, SHIFT/EDIT, ENTER/KEY MODE, FM/AM or MEMORY button. Note This function is useful especially for calling a station with weak signals which cannot be received by the automatic tuning method. If you store such a weak station by the manual preset tuning method beforehand, you can call it by its name any time easily. “A” will flash on the second letter or numeral position. 17  Calling a preset RDS station by the program type (PTY SEEK) By designating a program type, the unit automatically searches all preset stations for RDS stations of that program type. * There are 15 program types to classify RDS stations. For details, refer to page 15. 3, 5 1 2 4 1 Turn the unit into the PTY mode. Press once or twice until a program type is displayed or “NO PTY” flashes. –– PS/PTY/SEEK –– FREQ/PS/PTY SHIFT/EDIT ENTER/KEY MODE * If “NO PTY” flashes, proceed to the next step while flashing. If “NO PTY” disappears before you proceed to the next step, press the FREQ/PS/PTY button once or twice. 4 When the desired program type appears, press the ENTER/KEY MODE button. –– PS/PTY/SEEK –– FREQ/PS/PTY SHIFT/EDIT ENTER/KEY MODE ENTER Flashes. 5 PRESET STATIONS DOWN 2 UP Press once. TUNING –– PS/PTY/SEEK –– FREQ/PS/PTY SHIFT/EDIT ENTER/KEY MODE The program type of the station now being received or “NEWS” flashes on the display. 3 Select the desired program type. PRESET STATIONS DOWN UP TUNING * By pressing the PRESET STATIONS button repeatedly or by pressing and holding it, the display will change program types in sequence. 18 The unit begins searching all preset stations, and calls a station of the program type if such a station is found. * When the right side of the PRESET STATIONS button is pressed, the search is performed from “A1” toward higher numbers of the preset stations (A1, A2 ... A8, B1, B2, ...). If, however, “A3” is currently being called for example, the search begins from the next station “A4”. When the left side of the PRESET STATIONS button is pressed, the search is performed in reverse order. If the called station is not the desired one, press the PRESET STATIONS button again to search for another station of the same program type. To cancel this function Press the FREQ/PS/PTY, SHIFT/EDIT, ENTER/KEY MODE, FM/AM or MEMORY button.  The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the CD player, turntable and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this remote control transmitter will also control various functions of each component. English REMOTE CONTROL TRANSMITTER KEY FUNCTIONS For Control of This Unit The power to the receiver is automatically turned off one hour after this key is pressed (so that “SLEEP” lights up on the display). POWER PHONO Turns the power on/off. SLEEP SKIP SEARCH Selects preset station number + : Selects higher preset station number. – : Selects lower preset station number. A/B/C/D/E: Selects the page (A – E) of preset stations. – PRESET + DIR A DECK A/B PLAY CD PAUSE/STOP DISC STOP A/B/C/D/E TUNER DIR B TAPE 1 Selects input source. PLAY REC/PAUSE STOP TAPE 2 REC MUTE AUX – + Turns the volume level up/down. VOLUME For Other Component Control Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their function will be the same. On each key function, refer to the corresponding instruction on your component’s manual. POWER PHONO Controls compact disc player. * DISC SKIP is applicable only to a compact disc changer. SLEEP SKIP SEARCH – PRESET + DIR A DECK A/B PLAY PAUSE/STOP DISC STOP A/B/C/D/E TUNER DIR B TAPE 1 PLAY REC/PAUSE STOP CD TAPE 2 REC MUTE AUX – VOLUME + Controls tape deck. * DIR A, B and DECK A/B are applicable only to a double cassette tape deck. * For a single cassette deck with automatic reverse function, pressing DIR A will reverse the direction of tape running. 19  Standby mode While the power is on, pressing the POWER key on the remote control transmitter switches the unit to the Standby mode. (In this mode, the indicator is half illuminated.) Note The POWER switch on the front panel of this unit should be turned off when left unused for a long period of time. Standby mode POWER on mode NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery installation Remote control transmitter operation range 1 3 Remote control sensor 2 Within approximately 6 m (19.7 feet) 30° 30° Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes ● Use only AA, R6, UM-3 batteries for replacement. ● Be sure the polarities are correct. (See the illustration inside the battery compartment.) ● Remove the batteries if the remote control transmitter will not be used for an extended period of time. ● If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. 20 Notes ● There should be no large obstacles between the remote control transmitter and the main unit. ● If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting.  If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM Power cord is not plugged in or is not completely inserted. Firmly plug in the power cord. No sound. Incorrect output cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Appropriate input source is not selected. Select an appropriate input source with the INPUT selector. The TAPE 2 MONITOR switch is ON. Press the TAPE 2 MONITOR switch to turn it off. The protection circuit has activated because of short circuit etc. Turning the unit off and then on will reset the protection circuit. The SLEEP timer functioned. Cancel the SLEEP timer function. Incorrect setting of the BALANCE control Adjust it to the appropriate position. Incorrect cord connection. Connect the cords properly. If the problem persists, the cords may be defective. Incorrect cord connections. Firmly connect the audio plugs. If the problem persists, the cords may be defective. No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit. The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The player should be connected to the receiver through the MC head amplifier. The volume level cannot be increased, or sound is distorted. The power to the component connected to the REC OUT terminals of this unit is off. Turn the power to the component on. Using the BASS, TREBLE and BALANCE controls does not affect the tone. The PURE DIRECT switch is ON. The PURE DIRECT switch must be switched OFF to use those controls. FM stereo reception is noisy. Because of the characteristics of FM stereo broadcasts, this is limited to cases where the transmitter is too far or the antenna input is poor. Check the antenna connections. Try using a multiple element FM antenna. There is distortion and clear reception cannot be obtained even with a good FM antenna. There is multipath interference. Adjust antenna placement to eliminate multipath interference. A desired station cannot be tuned in with automatic tuning. The station is too weak. Use Manual tuning mode. Use high quality directional FM antenna. A desired station cannot be tuned in with automatic tuning. Weak signal or loose antenna connections. Use Manual tuning mode. There are continuous crackling and hissing noises. Noises will result from ligtning, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat but it is difficult to eliminate all noises. There are buzzing and whining noises (especially in the evening). A television set is being used nearby. Relocate this unit away from the TV. The remote control transmitter does not work. Direct sunlight or lighting (of an inverter type of flourescent lamp etc.) is striking the remote control sensor of the main unit. Change position of the main unit. The batteries of this remote control transmitter are too weak. Replace the batteries with new ones. The power to this unit is off. Turn the power to this unit on. Amplifier Only one side speaker outputs the sound. FM Sound “hums”. Remote control transmitter AM REMEDY The unit fails to turn on when the POWER switch is pressed. The sound suddenly goes off. Others CAUSE The sound is degraded when monitoring is performed by using the headphones connected to the compact disc player or cassette deck which are connected with this unit. English TROUBLESHOOTING Tighten the AM loop antenna connections and rotate it for best reception. 21  SPECIFICATIONS AUDIO SECTION FM SECTION AM SECTION Minimum RMS Output Power per Channel 8 ohms, 20 Hz to 20 kHz, 0.03% THD .......................................................50W+50W 6 ohms, 20 Hz to 20 kHz, 0.03% THD [General model only] ...................54W+54W Tuning Range [General model].................87.5 to 107.9 MHz [U.K. and Europe models] ..........................................87.5 to 108.0 MHz Tuning Range [U.K. and Europe models] .............................................531 to 1,611 kHz [General model] ...................530 to 1,710 kHz 50 dB Quieting Sensitivity (IHF, 75 ohms) Mono .................................1.55 µV (15.1 dBf) Stereo...................................21 µV (37.7 dBf) Usable Sensitivity ..............................100 µV/m Usable Sensitivity (75 ohms) (30 dB S/N Quieting, 1 kHz, 100% mod.) [General model] .................0.8 µV (9.3 dBf) DIN, Mono (S/N 26 dB) [U.K. and Europe models] .................0.9 µV DIN, Stereo (S/N 46 dB) [U.K. and Europe models] ..................24 µV Signal-to-Noise Ratio ...............................50 dB Image Response Ratio [General model].....................................45 dB [U.K. and Europe models] .....................80 dB AUDIO SECTION Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) 8/6/4/2 ohms ......................78/88/100/112W DIN Standard Output Power per Channel 4 ohms, 1 kHz, 0.7% THD [Europe model only]..............................65W IEC Power 8 ohms, 1 kHz, 0.03% THD [Europe model only]..............................60W Power Band Width 8 ohms, 25W, 0.06% THD ..............................................10 Hz to 50 kHz Damping Factor 8 ohms, 20 Hz to 20 kHz ...............90 or more Maximum Power (EIAJ) 1 kHz [General model only] ............................72W RIAA Equalization Deviation PHONO MM .....................................0±0.5 dB Total Harmonic Distortion (20 Hz to 20 kHz) PHONO MM to REC OUT (1V) ............0.02% CD/TAPE/AUX to SP OUT (25W/8 ohms) ....................................0.02% Signal-to-Noise Ratio (IHF-A Network) PHONO MM (5 mV Input Shorted)........82 dB CD/TAPE/AUX (Input Shorted) ...........105 dB Channel Separation (Vol. –30 dB) PHONO MM (Input Shorted 1 kHz) .........................60 dB Image Response Ratio ............................40 dB Spurious Response Ratio ........................50 dB Harmonic Distortion (1 kHz) ......................0.3% AM Suppression Ratio .............................55 dB Output Level/Impedance FM (100% mod., 1 kHz) [General model] ............500 mV/2.2 k-ohms [U.K. and Europe models (40 kHz Dev.)] ......................................400 mV/2.2 k-ohms AM (30% mod., 400 Hz) .........................................150 mV/2.2 k-ohms Capture Ratio..........................................1.5 dB GENERAL Alternate Channel Selectivity [General model].....................................85 dB Power Supply [U.K. and Europe models].....AC 230V, 50 Hz [General model] ....................AC 110/120/220/240V, 50/60 Hz IF Response Ratio ...................................80 dB Spurious Response Ratio ........................70 dB Selectivity (two signals, 40 kHz Dev.) [U.K. and Europe models] .....................70 dB Signal-to-Noise Ratio (IHF) Mono/Stereo [General model]........................80 dB/75 dB (DIN-Weighted, 40 kHz Dev.) Mono/Stereo [U.K. and Europe model] ..........74 dB/69 dB Harmonic Distortion Mono/Stereo (1 kHz) [General model] .............................0.1/0.2% Mono/Stereo (40 kHz Dev.) [U.K. and Europe models]..............0.1/0.2% Residual Noise (IHF-A Network)............100 µV Tone Control Characteristics BASS: Boost/cut .................±10 dB (50 Hz) Turnover frequency .............................................350 Hz TREBLE: Boost/cut............±10 dB (20 kHz) Turnover frequency .........................................3.5 kHz Selectivity.................................................32 dB Stereo Separation [General model] (1 kHz) ................................................50 dB [U.K. and Europe models] (40 kHz Dev.)......................................50 dB Frequency Response 20 Hz to 15 kHz................................0±1.5 dB 30 Hz to 13 kHz................................0±0.5 dB Power Consumption [U.K. and Europe models] .....................115W [General model].....................................135W AC Outlets 2 SWITCHED OUTLETS [Europe and General models] ...........................................100W max. total 1 SWITCHED OUTLET [U.K. model] .......................100W max. total Dimensions (W x H x D) ..........................................280 x 119 x 389 mm (11 x 4-11/16” x 15-5/16”) Weight...............................6.3 kg (13 lbs. 4 oz.) Accessories............................AM loop antenna Indoor FM antenna Remote control transmitter Batteries Specifications are subject to change without notice. 22  YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA VT 56040-1 Printed in Malaysia