Fr
Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils exempts de
licence d’Industrie Canada. Son utilisation est sujette aux deux conditions suivantes : 1) cet appareil ne
doit pas occasionner de brouillage préjudiciable et 2) cet appareil doit accepter toutes les interférences
reçues, notamment les interférences qui peuvent provoquer un fonctionnement non désiré.
NOTE DE LA FCC : Le fabricant n’est pas responsable des interférences sur les fréquences
radioélectriques ou télévisuelles pouvant être causées par des modifications non autorisées de ce
matériel. De telles modifications peuvent annuler le droit de l’utilisateur à utiliser cet appareil.
REMARQUE : Cet appareil a été testé et certifié conforme aux limites relatives aux appareils
numériques de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites ont été définies
afin de fournir une protection raisonnable contre le brouillage préjudiciable en milieu résidentiel. Cet
appareil produit, utilise et peut émettre des ondes de fréquence radio et, s’il n’est pas installé et utilisé
conformément aux instructions, il peut provoquer un brouillage préjudiciable aux communications
radio. Il n’existe toutefois aucune garantie que des interférences ne se produiront pas au sein d’une
installation donnée. Si cet appareil occasionne un brouillage préjudiciable à la réception radiophonique
ou télévisuelle, il suffit d’allumer et d’éteindre l’appareil pour déterminer sa responsabilité. Nous
encourageons l’utilisateur à essayer de corriger ces interférences en appliquant une ou plusieurs des
mesures suivantes :
— Réorienter ou déplacer l’antenne de réception.
— Augmenter la distance entre l’appareil et le récepteur.
— Brancher l’appareil à une prise secteur différente de celle du récepteur.
— Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs.
Remarque importante : Pour se conformer aux exigences de conformité de la FCC concernant
l’exposition aux RF, aucune modification apportée à l’antenne ou au dispositif n’est autorisée. Toute
modification apportée à l’antenne ou au dispositif pourrait faire en sorte que le dispositif dépasse les
exigences d’exposition aux RF et pourrait annuler le droit de l’utilisateur à utiliser ce dispositif.
En
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Important note: To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device could result in the device
exceeding the RF exposure requirements and void user’s authority to operate the device.
Es
Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC y con las
especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria de Canadá aplicables
a aparatos exentos de licencia. El funcionamiento está sujeto a las siguientes dos condiciones: (1)
este dispositivo no debe provocar interferencia perjudicial, y (2) este dispositivo debe aceptar toda
interferencia que reciba, incluso la que pudiera causar un funcionamiento no deseado.
NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio o TV
ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas modificaciones
podrían anular la autoridad del usuario para utilizar el equipo.
NOTA: Este equipo ha sido probado y cumple con los límites para aparatos digitales de Clase B,
de conformidad con el apartado 15 de las normas de la FCC. Estos límites están diseñados para
proveer protección razonable contra interferencias perjudiciales en una instalación residencial. Este
equipo genera, usa y puede irradiar energía de radiofrecuencias y, si no se instala y usa según las
instrucciones, puede provocar interferencia perjudicial a las radiocomunicaciones. No obstante, no
hay garantías de que no ocurrirá interferencia en una instalación en particular. Si este equipo provoca
interferencia perjudicial a la recepción de radio o televisión, lo que puede determinarse encendiendo y
apagando el equipo, se recomienda que el usuario intente corregir la
interferencia por medio de la implementación de una o más de las siguientes medidas:
— Reorientar o reubicar la antena receptora.
— Incrementar la separación entre el equipo y el receptor.
— Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que está
conectado el receptor.
— Consultar al distribuidor o a un técnico con experiencia en radio/televisión para
solicitar asistencia.
Nota importante: Para cumplir con los requisitos de cumplimiento de exposición de radiofrecuencia de
la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier cambio a la antena o dispositivo
podría hacer que el dispositivo supere los requerimientos de exposición de radiofrecuencia y anular la
autoridad del usuario para operar el dispositivo.
FCC — U2ZZW4002A | IC: 6924A-ZW4002A
Jasco Products Company | Model: ZW4002 / 14287
CAN ICES-3(B) / NMB-3(B)
All brand names shown are trademarks of their
respective owners.
Tous les noms de marque illustrés sont des marques
de commerce de leurs propriétaires respectifs.
Todas las marcas que aparecen aquí son marcas
registradas de sus respectivos dueños.
MADE IN CHINA/FABRIQUÉ EN CHINE/HECHO EN CHINA
GE IS A TRADEMARK OF GENERAL ELECTRIC COMPANY
AND IS UNDER LICENSE BY JASCO PRODUCTS
COMPANY LLC, 10 E. MEMORIAL RD.,
OKLAHOMA CITY, OK 73114.
© JASCO 2016 | 14287 | ZW4002 | rev. 10/20/16 RT v0
Z-Wave® Certified Wireless Lighting Control
Certifié Z-Wave® Commande d’éclairage sans fil
Control inalámbrico para iluminación certificado por Z-Wave®
ezzwave.com
Scan to view
installation guide
Balayez ce code pour
consulter le guide
d’installation.
Escanear para ver
la guía de instalación
14287
ZW4002
MANUAL • MANUEL • MANUAL
In-Wall
Smart Fan Control
Montage mural sans fil
Prise intelligent
Tomacorriente
inalàmbrico de pared
inteligente
SPECIFICATIONS
ZW4002
Power: 120 VAC, 60 Hz. | Signal (Frequency): 908.4/916 MHz.
Maximum Loads: 1.5A No more than two identical fans to the switch. Not to exceed 1.5 Amp resistive load.
CONTROLS FAN MOTOR ONLY. For use only with split capacitor or shaded pole ceiling fan motors.
Range: Up to 150 feet line of sight between the Wireless Controller and the closest Z-Wave receiver module.
Operating Temperature Range: 32-104° F (0-40° C)
For indoor use only.
Specifications subject to change without notice due to continuing product improvement
SPÉCIFICATIONS
ZW4002
Tension : 120 V c.a., 60 Hz. | Signal (fréquence) : 908,4/916 MHz.
Charges maximales : 1,5 A Pas plus de deux ventilateurs identiques pour l’interrupteur. La charge résistive ne doit
pas dépasser 1,5 ampère. COMMANDES DU MOTEUR DU VENTILATEUR UNIQUEMENT. À utiliser uniquement avec
un condensateur auxiliaire ou des moteurs à bague de déphasage pour ventilateurs.
Portée : Distance à vue entre la télécommande et le module de réception Z-Wave le plus proche allant jusqu’à
150 pi.
Plage de températures de fonctionnement : de 32 à 104 °F (de 0 à 40 °C).
Utilisation intérieure uniquement.
En raison d’améliorations continues du produit, les spécifications peuvent faire l’objet de changements sans
préavis.
ESPECIFICACIONES:
ZW4002
Alimentación: 120 VCA, 60 Hz. | Señal (Frecuencia): 908.4/916 MHz.
Cargas máximas: 1.5 A No más de dos ventiladores idénticos por interruptor. No deberá superar 1.5 Amp de
carga resistiva. CONTROLA SOLAMENTE EL MOTOR DEL VENTILADOR. Para uso exclusivo con ventiladores de
cielo raso que usen motores con condensador auxiliar o de polos sombreados.
Alcance: Hasta 150 pies (30.5m) en línea recta entre el controlador inalámbrico y el módulo receptor Z-Wave
más cercano.
Rango de temperatura de funcionamiento: 32-104 °F (0-40 °C).
Para uso en espacios interiores solamente.
Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto.
White (Neutral)
Green (Ground)
Black (Line / Hot)
Z-Wave
Primary
Black
(Load)
RIESGO DE INCENDIO
RIESGO DE DESCARGA ELÉCTRICA
RIESGO DE QUEMADURAS
CONTROL DE APARATOS:
PROCEDA CON SUMA PRECAUCIÓN AL USAR LOS
DISPOSITIVOS Z-WAVE PARA CONTROLAR EQUIPOS
ELECTRODOMÉSTICOS. EL DISPOSITIVO Z-WAVE
PUEDE FUNCIONAR EN UNA HABITACIÓN DIFERENTE
A LA DEL EQUIPO CONTROLADO. ADEMÁS, PODRÍA
PRODUCIRSE UNA ACTIVACIÓN ACCIDENTAL SI SE
OPRIME EL BOTÓN INCORRECTO EN EL CONTROL
REMOTO. LOS DISPOSITIVOS Z-WAVE PUEDEN
ENCENDERSE AUTOMÁTICAMENTE DEBIDO A EVENTOS
CRONOMETRADOS PROGRAMADOS. SEGÚN EL
EQUIPO DEL QUE SE TRATE, ESTE FUNCIONAMIENTO
ACCIDENTAL O SIN SUPERVISIÓN PODRÍA CREAR
UNA SITUACIÓN PELIGROSA. POR TALES MOTIVOS,
RECOMENDAMOS LO SIGUIENTE:
• NO USAR LOS DISPOSITIVOS Z-WAVE PARA
CONTROLAR CALENTADORES ELÉCTRICOS U OTROS
APARATOS ELECTRODOMÉSTICOS QUE PUDIERAN
IMPLICAR UN PELIGRO DEBIDO A UN ENCENDIDO SIN
SUPERVISIÓN, ACCIDENTAL O AUTOMÁTICO.
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CONTROLLING APPLIANCES:
EXERCISE EXTREME CAUTION WHEN USING Z-WAVE
DEVICES TO CONTROL APPLIANCES. OPERATION
OF THE Z-WAVE DEVICE MAY BE IN A DIFFERENT
ROOM THAN THE CONTROLLED APPLIANCE, ALSO
AN UNINTENTIONAL ACTIVATION MAY OCCUR IF
THE WRONG BUTTON ON THE REMOTE IS PRESSED.
Z-WAVE DEVICES MAY AUTOMATICALLY BE POWERED
ON DUE TO TIMED EVENT PROGRAMMING.
DEPENDING UPON THE APPLIANCE, THESE
UNATTENDED OR UNINTENTIONAL OPERATIONS
COULD POSSIBLY RESULT IN A HAZARDOUS
CONDITION. FOR THESE REASONS, WE RECOMMEND
THE FOLLOWING:
• DO NOT USE Z-WAVE DEVICES TO CONTROL
ELECTRIC HEATERS OR ANY OTHER APPLIANCES
WHICH MAY PRESENT A HAZARDOUS CONDITION
DUE TO UNATTENDED OR UNINTENTIONAL OR
AUTOMATIC POWER ON CONTROL.
RISQUE D’INCENDIE
RISQUE DE CHOC ÉLECTRIQUE
RISQUE DE BRÛLURES
COMMANDE DES APPAREILS :
SOYEZ TRÈS PRUDENT LORSQUE VOUS UTILISEZ
LES DISPOSITIFS Z-WAVE POUR COMMANDER
LES APPAREILS. LE DISPOSITIF Z-WAVE PEUT ÊTRE
UTILISÉ DANS UNE SALLE DIFFÉRENTE DE CELLE
DANS LAQUELLE SE TROUVE L’APPAREIL COMMANDÉ
ET UNE ACTIVATION INVOLONTAIRE PEUT AUSSI
SE PRODUIRE SI LE MAUVAIS BOUTON EST ACTIVÉ
SUR LA TÉLÉCOMMANDE. LES DISPOSITIFS Z-WAVE
POURRAIENT ÊTRE ACTIVÉS AUTOMATIQUEMENT
À CAUSE D’UN ÉVÉNEMENT PROGRAMMÉ. SELON
L’APPAREIL, CES UTILISATIONS INVOLONTAIRES ET
SANS SUPERVISION PEUVENT ENGENDRER UN RISQUE.
POUR CES RAISONS, NOUS RECOMMANDONS CE
QUI SUIT :
• N’UTILISEZ PAS LES DISPOSITIFS Z-WAVE POUR
COMMANDER LES RADIATEURS ÉLECTRIQUES OU
D’AUTRES APPAREILS QUI POURRAIENT PRÉSENTER
UN DANGER EN CAS DE COMMANDE D’ACTIVATION
IMPRÉVUE, INVOLONTAIRE OU AUTOMATIQUE.
AVERTISSEMENT
WARNING ADVERTENCIA
NOT FOR USE WITH MEDICAL OR
LIFE SUPPORT EQUIPMENT
Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED TO
SUPPLY POWER TO, OR CONTROL THE ON/OFF STATUS
OF MEDICAL AND/OR LIFE SUPPORT EQUIPMENT.
NE PAS UTILISER AVEC UN ÉQUIPEMENT
MÉDICAL OU DE SURVIE
LES DISPOSITIFS COMPATIBLES AVEC LA TECHNOLOGIE
Z-WAVE NE DEVRAIENT JAMAIS ÊTRE UTILISÉS POUR
ALIMENTER OU COMMANDER LA MISE EN MARCHE OU
L’ARRÊT DE L’ÉQUIPEMENT MÉDICAL OU DE SURVIE.
SE PROHÍBE SU EMPLEO EN EQUIPO MÉDICO
O EQUIPO PARA EL MANTENIMIENTO
DE LAS FUNCIONES VITALES
LOS DISPOSITIVOS Z-WAVE NUNCA SE DEBEN USAR
PARA SUMINISTRAR ENERGÍA ELÉCTRICA AL EQUIPO
MÉDICO O AL EQUIPO PARA EL MANTENIMIENTO DE
FUNCIONES VITALES, NI PARA CONTROLAR EL ESTADO
DE ENCENDIDO O APAGADO DE DICHOS EQUIPOS.
1.
IMPORTANT!
No more than two identical fans to the smart switch. Not to exceed 1.5 Amp resistive
load. CONTROLS FAN MOTOR ONLY. For use only with split
capacitor or shaded pole ceiling fan motors.
• Turn ON/OFF and adjust fan speed levels manually or remotely via the Z-Wave
controller
• Can be Included in multiple Groups and Scenes
• May be used in single pole installation or with up to two Jasco Add-on switches in
3-way or 4-way wiring configurations
• Interchangeable Paddle switch — White & light almond paddle in package
• Uses a standard, decorative-size wall plate for single gang installations (wall plate not
included)
• Blue LED indicates switch location in a dark room
• Z-Wave Certified for simple pairing and integrated home automation
• Screw Terminal Installation — requires wiring connections for Line (Hot), Load, Neutral,
and Ground. Traveler wire required for 3-way or 4-way installation
• This Z-Wave device has advanced features that allow you to customize your
experience. These features can only be adjusted by a Z-Wave enabled controller that
support the Z-Wave Configuration command class. For a complete list of Adjustable
Configurations, visit: www.byjasco.com/z-waveconfig
Getting to know your new Z-Wave device
A. Ground (Green/Bare)
B. Load (Black)
C. Line (Black)
D. Traveler (Red/Other)
E. Neutral (White)
F. Top Rocker — (Press & release to
turn fan control on, press & hold
increases speed)
G. Bottom Rocker — (Press & release
to turn fan control off, press & hold
to decrease speed)
Single, Dual And Triple Gang Boxes
When installing the In-wall Smart Fan Control in multiple gang boxes it may be neces-
sary to break off one or both sides of the scored tabs on the front yoke. This does not
affect the electrical rating of the switch (see specifications for details).
D
E
A
B
C
F
G
2.
Multi-switch wiring
For 3-way installations, please refer to Add-on Switch manual
Single switch wiring
Before you start; you may wish to change the paddle color to match your wallplate or decor.
Please proceed to section 5.
1. Shut off power to the circuit at circuit breaker or fuse box.
IMPORTANT! Verify power is OFF to switch box before continuing.
2. Remove wall plate.
3. Remove the switch mounting screws.
4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.
5. There are up to five screw terminals on the Switch; these are marked:
A. LINE (Hot) — Black (connected to power)
B. LINE — White
C. LOAD — Black (connected to fan)
D. GROUND — Green/Bare
E. TRAVELER — Red/Other (only in 3-way installations)
Match these screw terminals to the wires connected to the existing switch.
6. Disconnect the wires from the existing switch. Be careful to label wires according to the
previous terminal connection.
Observe Important Wiring Information
IMPORTANT! This Fan Control is rated for and intended to only be used with copper wire.
Wire Gauge Requirements
Use 14 AWG or larger wires suitable for at least 80° C for supplying Line (HOT), Load, Neutral,
Ground and Traveler connections.
Wire strip length
1. For attachment to screw terminals: Strip insulation 1” (25mm)
2. For attachment using the enclosure’s holes: Strip insulation 5/8” (16mm)
UL specifies that the tightening torque for the screws is 14 Kgf-cm (12 lbf-in).
3. Connect the green or bare copper ground wire to the GROUND terminal.
4. Connect the black wire that goes to the light to the terminal marked LOAD.
5. Connect the black wire that comes from the electrical service panel (Hot) to the terminal
marked LINE.
6. Connect the white wire to the neutral terminal (use jumper wire [not included] if needed).
NOTE:
The Traveler terminal is only used for 3-way or 4-way wiring and should remain insulated
if the Fan Control is being installed in a 2-way system (one switch & one load).
7. Insert Fan Control into the switch box being careful not to pinch or crush wires.
8. Secure the Fan Control to the box using the supplied screws.
9. Mount the wall plate.
10. Reapply power to the circuit at fuse box or circuit breaker and test the system.
Basic Operation
Note: Before starting, fan must be set to ‘HIGH’ position using pull chain.
The connected fan can then be turned ON/OFF and adjust speed levels in two ways:
1. Manually from the front panel rocker of the In-wall Fan Control
2. Remotely with a Z-Wave controller
Manual Control
1. To turn the connected fan ON: Press and release the top of the rocker.
NOTE: Fan will return to last speed setting of Fan Control. Default setting – HIGH.
2. To turn the fan OFF: Press and release the bottom of the rocker.
Adjust Fan Speed
The LED indicator confirms fan speed settings by flashing patterns
LOW – LED will blink every 2 seconds for 10 seconds
MEDIUM – LED will blink every second for 10 seconds
HIGH – LED will blink every half second for 10 seconds
1. To decrease fan speed: Press and hold lower rocker.
2. To increase fan speed: Press and hold upper rocker.
NOTE:
This switch only controls the fan motor and does not control any lighting that may be
part of the fan control. If your fan has an integrated light, a second light switch will need to be
installed separately to control the lighting load directly. No more than two identical fans should
be controlled by one switch. The total load of the fan(s) should not exceed 1.5A maximum.
Out to Light (Load)
A
D
E
C
B
From Breaker Box
From Breaker Box
Out to Light (Load)
A
B
E
D
C
OR
OR
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and fixture at the service
panel. All wiring connections must be made with the POWER OFF to avoid personal
injury and/or damage to the switch. This device is intended for installation in
accordance with the National Electric Code and local regulations in the United States,
or the Canadian Electrical Code and local regulations in Canada. If you are unsure or
uncomfortable about performing this installation consult a qualified electrician.
3.
Adding your device to a Z-Wave network
1. Follow the instructions for your Z-Wave certified controller to add
a device to the Z-Wave network.
2. Once the controller is ready to add your device, press and release
the top or bottom of the smart fan control switch (rocker) to add
it in the network.
Please reference the controller’s manual for instructions.
Now you have complete control to turn your fixture ON/OFF and
adjust fan speed levels according to groups, scenes, schedules and
interactive automations programmed by your controller.
If your Z-Wave certified controller features Remote Access, you can
now control your fixture from your mobile devices.
To remove and reset the device:
1. Follow the instructions for your Z-Wave certified controller to
remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press and
release the top or bottom of the wireless smart switch (rocker) to
remove it from the network.
To return your switch to factory defaults:
Quickly press ON (Top) button three (3) times then immediately press
the OFF (Bottom) button three (3) times. The LED will flash ON/OFF 5
times when completed successfully.
NOTE:
This should only be used in the event your network’s primary
controller is missing or otherwise inoperable
4.
The GE Add-on switch is required for
Multi-Switch 3-way or 4-way installations.
Connecting the traveler terminal of this switch
to a standard, non-GE switch will cause dam-
age or result in improper function. If this switch
is a part of a 3-way or 4-way multi-switch
installation, do not connect the traveler wire
or apply power until GE Add-on switches are
correctly installed. For more information on
3-Way or 4-Way installations, view the manual
or quick-start guide that comes with the GE
Add-on switch.
To Change Color Of The Paddle
This step is optional. Before you start you may want to change the color of the paddle to
match your wallplate or decor.
1. Lift the Air Gap tab at the base of the paddle.
2. Push side tabs in on one side and then the other to release paddle. Lift the cover up
and off.
3. Simply put the new paddle onto the Fan Control by inserting the air gap and side
tabs and snapping securely into place.
Once this step has been completed please return to section 3.
1.
2.
• This device supports Association Command Class (3 Groups)
• Association Group 1 supports Lifeline, Switch Multi-level Report
• Association Group 2 supports Basic Set and is controlled with the local load
• Association Group 3 supports Basic Set and is controlled by pressing the On or Off button
• Each Association Group supports 5 total nodes
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave
network with other Z-Wave certified devices from other
manufacturers and/or other applications. All non-battery
operated nodes within the network will act as repeaters
regardless of vendor to increase reliability of the network.
4.
Tools you will need
WARRANTY
JASCO Products warrants this product to be free from manufacturing defects for a period of
two years from the original date of consumer purchase. This warranty is limited to the repair or
replacement of this product only and does not extend to consequential or incidental damage to other
products that may be used with this product. This warranty is in lieu of all other warranties, expressed
or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the
exclusion or limitation of incidental or consequential damage, so the above limitations may not apply
to you. This warranty gives you specific rights, and you may also have other rights which vary from
state to state. Please contact Customer Service at 800-654-8483 (option 1) between 7AM – 8PM CST
or via our website (www.byjasco.com) if the unit should prove defective within the warranty period.
GARANTIE
JASCO Products garantit que ce produit est exempt de tout défaut de fabrication pour une période de
deux ans à compter de la date de l’achat original par l’acheteur. Cette garantie se limite exclusivement
à la réparation ou au remplacement de ce produit et n’est pas applicable aux dommages indirects
ou accessoires survenus sur d’autres produits utilisés avec ce produit. Cette garantie se substitue à
toute autre garantie expresse ou implicite. Certains États ne permettent pas de restrictions quant à
la durée d’une garantie implicite ou permettent l’exclusion ou la limitation des dommages indirects
et accessoires; il se peut, par conséquent, que cette garantie ne s’applique pas dans votre cas. Cette
garantie vous confère des droits juridiques précis; vous pouvez jouir d’autres droits qui peuvent varier
d’un État à l’autre. Veuillez communiquer avec le service à la clientèle au 1-800-654-8483 (option 1)
entre 7 h et 20 h (heure normale du Centre) ou par l’intermédiaire de notre site web (www.byjasco.
com) si l’appareil s’avère défaillant au cours de la période de garantie.
GARANTÍA
JASCO Products garantiza que este producto está libre de defectos de fabricación durante un periodo
de dos años a partir de la fecha original de compra por parte del consumidor. Esta garantía se
limita a la reparación o sustitución de este producto solamente y no se extiende a daños derivados
o accidentales causados a otros productos que se usen con esta unidad. Esa garantía remplaza
a todas las demás garantías expresas o implícitas. Algunos estados no autorizan limitaciones en
cuanto a la duración de una garantía implícita ni permiten la exclusión o limitación por daños
accidentales o derivados; por lo tanto, puede que las anteriores limitaciones no apliquen en su caso.
Esta garantía le da a usted derechos específicos, y otros que usted puede tener y que varían según
el estado en el que usted reside. Si la unidad resultare defectuosa dentro del periodo de garantía,
comuníquese por favor con Atención al Cliente en el 800-654-8483 (opción 1) entre 7 y 20 h, Hora del
Centro, o a través de nuestro sitio de internet (www.byjasco.com).
JASCO Products Company LLC, Building B
10 E. Memorial Rd. Oklahoma City, OK 73114.
FCC / IC
If you have any problems or questions, contact our tech support team at
1-800-654-8483, (option 1) Monday–Friday, 7AM–8PM CST.
For the most up-to-date product support, accessories, electronic (PDF) format
manuals and more, visit www.byjasco.com/support.
• No user serviceable parts in this unit.
Si vous avez des problèmes ou des questions, communiquez avec notre
équipe de soutien technique au 1-800-654-8483, option 1, du lundi au vendredi,
de 7 h à 20 h (HNC).
Pour le soutien relatif aux produits le plus à jour, les accessoires, les manuels en
format électronique (PDF) et plus encore, visitez le site www.byjasco.com/support.
• Aucune des pièces de ce dispositif ne peut être réparée par l’utilisateur.
Si tiene problemas o dudas, comuníquese con nuestro equipo técnico al número:
1-800-654-8483, opción 1 de lunes a viernes, de 7 a.m. a 8 p.m., hora estándar del
centro (CST).
Para recibir el soporte técnico más actualizado sobre productos, accesorios,
manuales en formato digital (PDF), entre otros, visite www.byjasco.com/support.
• Esta unidad no contiene piezas que el usuario pueda reparar.
DO NOT RETURN THIS
PRODUCT TO THE STORE
NE RETOURNEZ PAS
CE PRODUIT AU MAGASIN
NO DEVUELVA ESTE
PRODUCTO A LA TIENDA
STOP
Model: 14287 / ZW4002
Thisliteraturewillbeavailableonourquickstartguideoronourwebsiteatthefollowingaddressin
thefuture:www.jascoproducts.com/z‐waveconfig
ADVANCED OPERATION
The following Advanced Operation parameters require that you have a controller that supports the advanced configuration
command class.
All On/All Off
Depending upon your primary controller, this Z-Wave module can be set to respond to ALL ON and ALL OFF commands in up
to four different ways. Some controllers may not be able to change the response from its default setting. Please refer to your
controller’s instructions for information on whether or not it supports the configuration function and if so, how to change this
setting.
The four possible responses are:
1. It will respond to ALL ON and the ALL OFF commands (default).
2. It will not respond to ALL ON or ALL OFF commands.
3. It will respond to the ALL OFF command but will not respond to the ALL ON command.
4. It will respond to the ALL ON command but will not respond to the ALL OFF command.
AssociationGroupStatement
•ThisdevicesupportsAssociationCommandClass(3Groups)
•AssociationGroup1supportsLifeline,BinarySwitchReport
•AssociationGroup2supportsBasicSetandiscontrolledwiththelocalload
•AssociationGroup3supportsBasicSetandiscontrolledbydoublepressingtheOnorOffbutton
•EachAssociationGroupsupports5totalnodes
FactoryReset
1.QuicklypressON(Top)button3timesthenimmediatelypresstheOFF(bottom)button3times.TheLEDwill
flashON/OFF5timeswhencompletedsuccessfully.
-
1
-
2
