Maytag M1TXEGMY User Instructions

Marca: Maytag

Modelo: M1TXEGMY

Categoría: Neveras

Tipo: User Instructions

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING or

PROBLEM SOLVER, please visit our website at www.maytag.com for additional information. If you still need assistance, call us

at 1-800-688-9900. In Canada, visit our website at www.maytag.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Table of Contents / Índice / Table des matières

REFRIGERATOR SAFETY ........................ 2

INSTALLATION INSTRUCTIONS............. 3

Unpack the Refrigerator.......................... 3

Proper Disposal of

Your Old Refrigerator.............................. 3

Location Requirements........................... 4

Electrical Requirements.......................... 4

Water Supply Requirements................... 5

Connect the Water Supply ..................... 5

Refrigerator Doors................................... 6

Reversibility Kit Instructions.................. 13

Adjust the Doors ................................... 13

Install Air Filter....................................... 14

Install Produce Preserver...................... 14

REFRIGERATOR USE............................. 15

Using the Controls ................................ 15

REFRIGERATOR FEATURES................. 16

Refrigerator Shelves.............................. 16

Meat Drawer.......................................... 17

Crisper................................................... 17

FREEZER FEATURES............................. 18

Wire Freezer Shelf................................. 18

Glass Freezer Shelf............................... 18

DOOR FEATURES................................... 18

Door Rails.............................................. 18

Door Bins .............................................. 19

Utility Compartment and Can Caddy ... 19

Ice Maker .............................................. 19

Water Filtration System......................... 20

REFRIGERATOR CARE.......................... 20

Cleaning ................................................ 20

Changing the Light Bulbs ..................... 21

TROUBLESHOOTING............................. 22

Refrigerator Operation .......................... 22

Temperature and Moisture ................... 22

Ice and Water........................................ 23

ACCESSORIES........................................ 23

WATER FILTER CERTIFICATIONS........ 23

PERFORMANCE DATA SHEET ............. 24

WARRANTY........................................25-26

SEGURIDAD DEL REFRIGERADOR...... 28

INSTRUCCIONES DE INSTALACIÓN....29

Desempaque el refrigerador ................. 29

Cómo deshacerse adecuadamente

de su refrigerador viejo ......................... 29

Requisitos de ubicación........................ 30

Requisitos eléctricos............................. 30

Requisitos del suministro de agua........ 30

Conexión del suministro de agua ......... 31

Puertas del refrigerador ........................ 32

Instrucciones del juego para invertir..... 39

Ajuste las puertas.................................. 39

Instalación del filtro de aire ................... 40

Instalación del preservador

de alimentos frescos............................. 41

USO DE SU REFRIGERADOR................ 42

Uso de los controles ............................. 42

CARACTERÍSTICAS DEL

REFRIGERADOR..................................... 43

Estantes del refrigerador....................... 43

Cajón para carnes................................. 44

Cajón para verduras.............................. 44

CARACTERÍSTICAS

DEL CONGELADOR................................ 45

Estante de alambre del congelador...... 45

Estante de vidrio del congelador .......... 45

CARACTERÍSTICAS DE LA PUERTA.... 46

Rieles de la puerta................................. 46

Recipientes de la puerta ....................... 46

Compartimiento de uso

general y portalatas............................... 46

Fábrica de hielo..................................... 46

Sistema de filtración de agua ............... 47

CUIDADO DE SU REFRIGERADOR ...... 48

Limpieza ................................................ 48

Cómo cambiar los focos....................... 48

SOLUCIÓN DE PROBLEMAS................. 49

Funcionamiento del refrigerador........... 49

Temperatura y humedad....................... 50

Hielo y agua........................................... 50

ACCESORIOS.......................................... 51

HOJA DE DATOS

DEL RENDIMIENTO ................................ 52

GARANTÍA...........................................53-54

SÉCURITÉ DU RÉFRIGÉRATEUR..........56

INSTRUCTIONS D'INSTALLATION........57

Déballage du réfrigérateur.....................57

Mise au rebut appropriée

de votre vieux réfrigérateur ...................57

Exigences d'emplacement....................58

Spécifications électriques .....................58

Spécifications de

l’alimentation en eau..............................58

Raccordement de la

canalisation d'eau..................................59

Portes du réfrigérateur ..........................60

Instructions pour l'ensemble

d’inversion du sens d’ouverture............67

Ajustement des portes ..........................67

Installation du filtre à air.........................68

Installation du conservateur

pour produits frais .................................69

UTILISATION DU RÉFRIGÉRATEUR.....70

Utilisation des commandes...................70

CARACTÉRISTIQUES DU

RÉFRIGÉRATEUR....................................71

Tablettes du réfrigérateur......................71

Tiroir à viande ........................................72

Bac à légumes.......................................72

CARACTÉRISTIQUES

DU CONGÉLATEUR ................................73

Tablette métallique du congélateur.......73

Tablette en verre du congélateur ..........73

CARACTÉRISTIQUES DE LA PORTE....74

Tringles dans la porte............................74

Balconnets de porte..............................74

Compartiment utilitaire et

compartiment à canettes ......................74

Machine à glaçons ................................74

Système de filtration de l'eau................75

ENTRETIEN DU RÉFRIGÉRATEUR .......76

Nettoyage ..............................................76

Remplacement des

ampoules d’éclairage ............................76

DÉPANNAGE............................................77

Fonctionnement du réfrigérateur...........77

Température et humidité.......................78

Glaçons et eau.......................................78

ACCESSOIRES ........................................79

FEUILLE DE DONNÉES

SUR LA PERFORMANCE........................80

GARANTIE.......................................... 81-82

REFRIGERATOR

USER INSTRUCTIONS

W10551723A

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock, or injury to persons when using the refrigerator, follow basic precautions,

including the following:

WARNING:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Remove the Packaging

IMPORTANT: Do not remove the white foam air return insert from

behind the control panel on the ceiling of the refrigerator. If the

insert is removed, ice may migrate down from the freezer and

cause icicles to form.

■ Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Rinse with warm water

and dry with a soft cloth.

■ Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information see “Refrigerator Safety.”

Clean Before Using

After you remove all of the package materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

“Refrigerator Care.”

Proper Disposal of

Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

– even if they will sit for “just a few days.” If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as floor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Location Requirements

IMPORTANT: This refrigerator is designed for indoor household

use only.

To ensure proper ventilation for your refrigerator, allow for ½"

(1.25 cm) of space on each side and at the top. Allow for 1"

(2.54 cm) of space behind the refrigerator. If your refrigerator has

an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space on the hinge side (some

models require more) to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature range

for optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control

(Thermostat, Refrigerator or Freezer Control depending on the

model) to OFF, and then disconnect the refrigerator from the

electrical source. When you are finished, reconnect the

refrigerator to the electrical source and turn cooling on or reset

the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting. See “Using the

Controls” in the User Instructions, User Guide, or Use & Care

Guide.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

2" (1.25 cm)

2" (5.08 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Water Supply Requirements

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

IMPORTANT:

■ All installations must meet local plumbing code requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFF.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

5. Using a cordless drill, drill a ¹⁄₄" hole in the cold water pipe

you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" drilled hole

in the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws

slowly and evenly so washer makes a watertight seal. Do not

overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the

copper tubing.

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" Open-end or two

adjustable wrenches

■ ¹⁄₄" Nut driver

■ ¹⁄₄" Drill bit

■ Cordless drill

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

DEF

Connect to Refrigerator

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do

not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the ¹⁄₄" (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

Refrigerator Doors

Depending on the width of your doorway, you may need to

remove the doors to move the refrigerator into your home. Also,

the door hinges are factory installed on the right-hand side. If you

want the door to open from the other direction, you must reverse

the door swing.

IMPORTANT:

■ Before you begin, turn the refrigerator control OFF, unplug

refrigerator or disconnect power. Remove food and any

adjustable door or utility bins from doors.

■ Depending on your model, your refrigerator has either

Style1-Contour Doors or Style 2 - Standard Doors.

Reference the graphic specific to your model later in this

section following “Final Steps.”

NOTE: For contour door models only - A Reversibility kit,

which includes a new Brand Badge and hole covers, is

available. To purchase a reversibility kit, see “Accessories” for

contact information, and order Part Number W10395149.

Tools Needed: ⁵⁄₁₆" hex head socket wrench, #2 Phillips

screwdriver, flat-blade screwdriver, ⁵⁄₁₆" open-end wrench, flat 2"

putty knife.

Remove Doors and Hinges

⁵⁄₁₆

" Hex Head Hinge Screw

1. Unplug refrigerator or disconnect power.

2. Using a hex head socket wrench, remove the three ⁵⁄₁₆" hex

head hinge screws from the top hinge and lift up to remove

the hinge.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Lift the freezer door off of the center hinge and set it aside.

4. Remove the washer from the top of the Center Hinge pin.

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

⁵⁄₁₆

" Hex head hinge screws

B. Top hinge

C. Hinge pin

D. Spacer

A. Washer

5. Open refrigerator door and remove base grille from the

bottom front of the refrigerator.

6. Using a hex head socket wrench, remove the two ⁵⁄₁₆" hex

head hinge screws attaching the bottom hinge to the cabinet

and remove the hinge from the bottom of the refrigerator

door.

NOTE: For 21 cu ft models, remove both the Bottom Hinge

assembly and the leveling foot.

7. Lower the refrigerator door from the Center Hinge.

8. Remove the washer from the bottom of the Center Hinge pin.

9. Using a hex head socket wrench, remove the three screws

from the center hinge and remove the hinge. Set aside.

Reverse Doors and Hinges (optional)

IMPORTANT:

Your refrigerator has handles that either extend from the door or

cup handles which are recessed into the doors. If your model has

cup handles, disregard instructions pertaining to moving the

handles to the opposite side.

■ See complete graphics later in these instructions.

Reverse Center Hinge

1. Remove the three screws (that match the exterior finish) from

the handle side and use them to fill the holes created when

the hinge screws were removed.

2. Using the three ⁵⁄₁₆" hex head hinge screws, removed in

Step 9, insert two screws halfway into the holes, leaving

space to insert the Center Hinge.

3. Slide the center hinge, from the right, onto the screws, insert

the third screw, and tighten all screws completely.

NOTE: Make sure the washers are in place on both the top

and bottom pins of the center hinge.

A. Clips

A. Washer

A. Center hinge

⁵⁄₁₆

" Hex head hinge screws

A. Screws matching exterior finish

⁵⁄₁₆

" Hex head hinge screws

B. Washers

Door Handle

Screw Hole Plug

Round-Head

Handle Screw

Reverse Freezer Door

1. Remove the three cabinet hole plugs from the top of the

cabinet and place them in the hinge holes on the opposite

side.

2. Remove the two screws from the bottom of the freezer door

handle.

3. Slide the handle downward to release it from the keyhole slot

and pull the handle away from the door.

4. Using the plastic tool (provided), remove the brand badge

from the freezer door by prying up the right-hand side and

slowly peeling the badge away from the door, revealing the

hole to mount the door handle.

NOTES:

■ To avoid scratching the finish, do not use a sharp or

metallic object to pry the brand badge from the door.

■ Rub a small amount of liquid dish soap over any adhesive

residue with your fingers. Rinse the door with warm water

and dry with a soft cloth.

5. Remove the shoulder screw from the left-hand side of the

door and fasten it into the hole that was behind the brand

badge.

6. Align the keyhole slot in the handle mounting bracket with the

shoulder screw. Position the handle so that the mounting

base is flush against the door. Slide the handle upward until it

locks into place.

7. Fasten the bottom of the handle to the bottom of the freezer

door.

8. Remove the door stop from the bottom of the freezer door.

9. Move the door stop to the opposite side making sure that the

hole in the door stop plate is aligned perfectly with the hole

for the center hinge pin.

10. Using the screw removed in Step 9, fasten the door stop to

the bottom of the freezer door.

11. Tighten all screws. Set aside the freezer door until the hinges

and refrigerator door are in place.

Reverse Refrigerator Door

1. Remove the door stop from the bottom of the refrigerator

door.

1. Replace the door stop on the opposite side of the refrigerator

door, making sure that the hole in the door stop plate is

aligned perfectly with the hole for the bottom hinge pin.

2. Fasten the door stop to the door.

3. Remove the screws from the top of the refrigerator door

handle.

A. Freezer handle B. Flat-head handle screws

A. Door stop screw

B. Door stop

A. Door stop screw

B. Door stop

4. Slide the handle upward to release it from the keyhole slot

and pull the handle away from the door.

5. Remove the decal covering the hole on the opposite side of

the door, where the refrigerator door handle will be installed,

and discard the decal.

6. Remove the shoulder screw from the left-hand side of the

door and fasten it into the hole in the door that was behind

the decal.

7. Align the keyhole slot in the handle mounting bracket with the

shoulder screw. Position the handle so that the mounting

base is flush against the door. Slide the handle downward

until it locks into place.

8. Fasten the top of the refrigerator handle to the top of the

refrigerator door.

9. Cover the remaining hole with the decal (provided).

10. Tighten all screws. Set aside refrigerator door until bottom

hinge is installed on the opposite side of the refrigerator.

NOTE: For 21 cu ft models, transfer both the bottom hinge

assembly and the leveling foot to the opposite side.

Reverse Top Hinge

1. Remove the screw attaching the hinge pin to the hinge. Turn

the hinge over so that it is pointing in the opposite direction.

2. Place the plastic spacer beneath the hinge so that it will be

between the hinge and the cabinet, making sure the holes are

aligned.

3. Fasten the Top Hinge to the opposite side of the cabinet,

inserting the screws only halfway, so you will be able to

replace and align the freezer door later.

A. Flat-head handle screws B. Refrigerator door handle

A. Flat-head handle screws

A. Plastic spacer

B. Hinge pin screw

C. Hinge pin

⁵⁄₁₆

" Hex head hinge screws

B. Top hinge pin

C. Plastic spacer

Replace Doors and Hinges

IMPORTANT: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets to

hold the doors in place while you are working.

Install Refrigerator Door

1. Place the washer on the hole on top of the refrigerator door.

2. Lift the refrigerator door onto the bottom pin of the Center

hinge, and rest the door on the magnetic shipping bracket to

ensure proper alignment.

NOTE: If the shipping bracket is no longer there, the distance

between the bottom of the door and the floor must be 3.46"

(8.8 cm).

3. Insert the bottom hinge pin into the bottom of the refrigerator

door and fasten the hinge to the cabinet. Do not tighten

completely.

NOTE: For 21 cu ft models, install both the bottom hinge

assembly and the leveling foot.

4. Measure the distance from the bottom of the refrigerator door

to the floor. The distance should be approximately 3¹⁄₂"

(88 mm).

NOTE: If necessary, loosen the bottom hinge, without

removing the screws, adjust the door to the correct height

and fully tighten the screws.

Install Freezer Door

1. Place washer on the upper hinge pin of the Center Hinge.

2. Place the freezer door on the upper hinge pin of the Center

Hinge.

3. Insert the Top Hinge pin into the drilled hole in the top of the

freezer door. Do not tighten the screws completely.

4. Align the doors so that the bottom of the freezer door aligns

evenly with the top of the refrigerator door. Tighten all screws.

NOTE: The distance between the doors should be

approximately ⁵⁄₈" (16 mm).

Final Steps

1. Remove the cover from each side of the base grille. Move

each cover to the opposite side.

NOTE: The shorter cover must be on the hinge side of the

base grille.

2. Align the clips on the base grille with the screws on the

bottom of the cabinet. Push the base grille toward the cabinet

until it is flush.

3. Plug in the refrigerator or reconnect the power.

4. Reset the controls. See “Using the Controls.”

5. Return all removable door parts to doors and food to

refrigerator.

A. Bottom hinge

A. Cover

Style 1–Contour Doors

Door Removal &

Replacement

Door Swing Reversal (optional)

B. Flat-Head Handle Screws

A. Freezer Handle

A. Cabinet Hinge Hole Plugs

1-2

A. Door Handle Sealing Screws

A. Bottom Hinge

B. Screws

C. Leveling Leg (on some models)

Top Hinge

Bottom Hinge

Center Hinge

A. Center Hinge

⁵⁄₁₆

" Hex-Head Hinge Screws

⁵⁄₁₆

" Hex-Head Hinge Screws

B. Top Hinge

C. Hinge Pin

⁵⁄₁₆

" Hex-Head Hinge Screws

1-1

Door Handle

Seal Screw Front

A. Door Hinge Hole Plug

A. Flat-Head Handle Screws

B. Refrigerator Handle

A. Door Stop Screw

B. Door Stop

Side View

Front View

Base Grille

Plastic Handle

A. Cup Handle

Cup Handle

⁵⁄₁₆

" Hex-Head

Hinge Screws

B. Top Hinge

C. Hinge Pin

Style 2–Standard Doors

Door Removal &

Replacement

Door Swing Reversal (optional)

A. Door Hinge Hole Plug

A. Flat-Head Handle Screws

B. Freezer Handle

A. Cabinet Hinge Hole Plugs

A. Door Handle Sealing Screws

A. Door Stop Screw

B. Door Stop

Door Handle

Seal Screw Front

1-2

6-1

A. Door Handle

6-2

A. Flat-Head

Handle Screw

B. Refrigerator Handle

C. Handle Screw

6-3

Screw Cover

Side View

Front View

A. Bottom Hinge

⁵⁄₁₆

Hex-Head Hinge Screws

Top Hinge

Bottom Hinge

Center Hinge

A. Center Hinge

⁵⁄₁₆

Hex-Head Hinge Screws

A. Top Hinge Cover

⁵⁄₁₆

Hex-Head Hinge Screws

C. Top Hinge

1-1

Base Grille

A. Bottom Hinge Hole Plug

⁵⁄₁₆

Hex-Head Hinge Screws

Reversibility Kit Instructions

(contour door models only)

If your model came with a Reversibility kit or you purchased a kit

for your contour door refrigerator, please use the Brand Badge

Placement template and the following instructions to install the

Brand Badge on the opposite side of the freezer door.

Parts Included:

Brand badge removal tool

Brand badge template (on last page of User Instructions)

Hole cover decal (color coordinated to exterior)

Tools Needed:

Scissors

Masking tape

Freezer Door

1. Using the removal tool (provided), remove the brand badge

from the freezer door by lifting up the right-hand side and

peeling the badge away from the door from right to left.

NOTE: To avoid scratching the door, do not use a sharp or

metallic object to pry the brand badge from the door.

2. Rub a small amount of liquid dish soap over any adhesive

residue with your fingers. Rinse the door with warm water and

dry with a soft cloth.

3. Cut the template along the dotted lines that match the shape

of the brand badge.

4. Align the edges of the template with the side and top of the

freezer door and tape the template to the door.

NOTE: When the template is correctly aligned, the hole in the

door, where the handle was, will be within the cutout of the

template, as shown.

5. Using the cutout as a guide, press the brand badge onto the

freezer door making sure that the hole is completely covered.

6. Slowly remove the template.

Adjust the Doors

IMPORTANT: To comply with American Disabilities Act (ADA)

guidelines, fully retract the rollers into the cabinet to lower the

refrigerator.

Door Closing

Your refrigerator has two front adjustable rollers – one on the right

and one on the left. If your refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt using

the following instructions:

1. Remove the base grille. See the Base Grille graphic in

“Refrigerator Doors.” The two leveling screws are part of the

front roller assemblies, which are at the base of the

refrigerator on either side.

2. Use a socket driver to adjust the leveling screws. Turn the

leveling screw to the right to raise that side of the refrigerator

or turn the leveling screw to the left to lower that side. It may

take several turns of the leveling screws to adjust the tilt of

the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers which makes it easier to adjust.

3. Open both doors again to make sure they close as easily as

you like and that they stay closed. If not, tilt the refrigerator

slightly more to the rear by turning both leveling screws to the

right. It may take several more turns.

NOTES:

■ To keep the refrigerator level, you should turn both

leveling screws the same amount.

■ On models with the leveling/roller assembly, after

adjusting the refrigerator to the desired tilt, turn the

leveling leg until it is firmly against the floor as shown.

On some models

4. Replace the base grille.

A. Bottom hinge

B. Screws

C. Leveling/roller assembly

Door Aligning

If the space between your doors looks uneven, you can adjust it

using the following instructions:

1. Pry off the top hinge cover.

2. Loosen the top hinge screws using a ⁵⁄₁₆" socket or wrench.

3. Have someone hold the door in place or put a spacer

between the doors while you tighten the top hinge screws.

4. Replace the top hinge cover.

Install Air Filter

(on some models)

On some models, your refrigerator's accessory packet includes

an air filter, which must be installed prior to use. On some

models, the air filter is already installed at the factory.

The air filter reduces the buildup of odors. This helps to maintain

a cleaner environment inside the refrigerator.

Installing the Air Filter (on some models)

The filter should be installed behind the vented door, which is

located (depending on your model) along either the rear or left

interior wall near the top of the refrigerator compartment.

1. Remove the air filter from its packaging.

2. Lift open the vented door.

3. Snap the filter into place.

Air Filter Status Indicator (on some models)

Style 1 - Install Manual Air Filter Status Indicator

The filter comes with a status indicator, which should be

activated and installed at the same time the air filter is installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator,

until the bubble pops to activate the indicator.

3. Lift open the vented air filter door. On some models, there are

notches behind the door.

On models with notches:

■ Slide the indicator down into the notches, facing outward.

NOTE: The indicator will not easily slide into the notches

if the rear bubble has not been popped.

■ Close the air filter door, and check that the indicator is

visible through the rectangular hole in the door.

On models without notches:

■ Store the indicator in a visible place you will easily

remember - either inside the refrigerator, or elsewhere in

your kitchen or home.

Style 2 - Air Filter Status on Electronic Control Display

The control panel displays the Air Filter status.

■ GOOD - The air filter LED does not light up.

■ REPLACE - The air filter LED lights up constantly when the

refrigerator door is open.

■ EXPIRED - The air filter LED lights up constantly and flashes

when the refrigerator door is open.

After replacing the air filter, press and hold FILTERS RESET for

3 seconds. The filter icons will turn off. See “Using the

Control(s).”

NOTE: At any filter status, pressing and holding FILTERS RESET

for 3 seconds will reset the air filter status to good and the air

filter LED will turn off.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, or

when the status indicator air filter icon LED turns on and starts

flashing when the refrigerator door is opened.

To order a replacement air filter, contact us using the

assistance/service information following the warranty.

1. Remove the old air filter by squeezing in on the side tabs.

2. Remove the old status indicator.

3. Install the new air filter and reset the status indicator using

the instructions in the previous sections.

Install Produce Preserver

(on some models)

The accessory packet includes two produce preserver pouches,

which should be installed in a crisper drawer prior to use.

NOTE: For best performance, always use two pouches.

The produce preserver absorbs ethylene, to slow the ripening

process of many produce items. As a result, certain produce

items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

MONTHS

REPLACE

Produces Ethylene

Very

Low

Low High Very

High

Sensitivity

to Ethylene

High Broccoli

Lettuce

Spinach

Apples

Pears

Med. Asparagus

Citrus fruit

Cantaloupe

Low Carrots

Grapes

Berries

Installing the Produce Preserver

The produce preserver pouches should be installed in the

housing, located on the wall of one of the crisper drawers.

1. Remove the FreshFlow™ Produce Preserver pouches from

the packaging.

2. Lift up on the housing to remove it from the mounting tab.

3. Open the housing by pulling up and out on the back of the

top of the housing.

4. Place both pouches inside the housing, then snap the

housing back together.

5. Place the housing back on the mounting tab.

Installing the Status Indicator

The produce preserver comes with a status indicator, which

should be activated and installed at the same time the pouches

are installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator until

the bubble pops, to activate the indicator.

3. Slide open the cap on the top of the produce preserver

housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible

through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator’s bubble

has not been popped.

Replacing the Produce Preserver

The disposable pouches should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order replacements, contact us. See “Accessories” for

information on ordering.

1. Remove the used pouches from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement pouches and status indicator using

the instructions in the previous sections.

REFRIGERATOR USE

Using the Controls

The temperature controls are located at the top front of the

refrigerator or freezer compartments.

Temperature Controls

For your convenience, the temperature controls are preset at the

factory. When you first install your refrigerator, make sure the

controls are still set to the recommended setting as shown.

Style 1

Recommended Setting

Style 2

Recommended Setting

Style 3

Recommended Setting “3 Snowflakes”

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

CAUTION

ITA

Read cautions on back.

ATTENTION

Lisez des prudences sur le revers.

MONTHS

REPLACE

IMPORTANT:

■ The recommended setting should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream

is firm.

■ Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has

cooled completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool

the compartments any faster.

■ If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

To Turn Cooling Off/On:

Styles 1 and 2 - Press and hold TEMP for 3 seconds to turn

cooling off. To turn cooling back on, press and hold TEMP again

for 3 seconds.

Style 3 - Move the dial control to the word OFF. To turn cooling

back on, move the dial control to the desired temperature setting.

NOTE: Neither compartment will cool when the control is set to

OFF.

Adjusting Controls

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart below as

a guide.

Styles 1 and 2 - Electronic Controls

■ Press the TEMP button to toggle among the four LED lights

which indicate the temperature setting. Reading from left to

right, the LED in the first position is the least cold. The LEDs

indicate increasingly colder settings as you continue to the

right until all four LEDs are illuminated.

NOTE: For the first to fourth setting, only one LED of the four

LEDs will be lit. All four LEDs will be lit when you have

reached the coldest setting.

Style 3 - Dial Control

■ Move the dial to the desired number of snowflakes from

(1 least cold to 5 coldest).

NOTE: Except when starting the refrigerator, do not adjust the

control more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

Additional Features

SpeedCool (on some models)

The SpeedCool feature assists with periods of high refrigerator

use, full grocery loads or temporarily warm room temperatures.

■ Press SPEED COOL to set the freezer and refrigerator to the

lowest temperature settings. Press SPEED COOL again to

return to the selected temperature set point.

NOTE: The SpeedCool icon will be illuminated when

SpeedCool is selected. If you try to adjust the temperature

when SpeedCool is on, the SpeedCool icon will blink three

times and then turn off.

Filter Reset (on some models)

The Filter Reset control allows you to restart the filter status

tracking feature each time you replace the air filter or water filter.

■ Press and hold FILTER RESET for 3 seconds. The filter icons

will turn off. See “Install Air Filter” and “Water Filtration

System.”

REFRIGERATOR

FEATURES

Your model may have some or all of these features.

Refrigerator Shelves

(Glass shelves on some models)

The shelves in your refrigerator are adjustable to match your

individual storage needs.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will make it

easier to find the exact item you want. It will also reduce the

amount of time the refrigerator door is open, and save energy.

Shelves and Glass Shelves (on some models)

To remove and replace a shelf:

1. Remove items from the shelf.

2. Slide the shelf straight out to the stop.

3. Depending on your model, lift back or front of the shelf past

the stop. Slide shelf out the rest of the way.

4. Replace the shelf by sliding the back of the shelf into the

track in the wall of the cabinet.

5. Guide the front of the shelf into the shelf track. Be sure to

slide the shelf in all the way.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR

Control one setting

higher

FREEZER too warm/too little ice FREEZER Control one

setting higher

REFRIGERATOR too cold REFRIGERATOR

Control one setting

lower

FREEZER too cold FREEZER Control one

setting lower

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Fold Away Shelf (on some models)

To remove and replace a shelf:

1. To remove the entire shelf, tilt up the front of the shelf and

slide it out toward you.

2. To remove the front-half of the shelf, hold the front of the shelf

with one hand and press up in the center of the shelf. Then

push down and in on the shelf until it slides beneath the back

half of the shelf.

3. Replace the entire shelf by guiding it into the door liner and

pushing it inward until it stops. Then, tilt the front of the shelf

upward until the stopper is overcome and slide it in.

Meat Drawer

(on some models)

To remove and replace the meat drawer:

1. Slide meat drawer out to the stop.

2. Lift front of meat drawer with one hand while supporting

bottom of drawer with other hand. Slide drawer out the rest of

the way.

3. Replace the drawer by sliding it back in fully past the drawer

stop.

Meat Drawer Cover (on some models)

To remove and replace the meat drawer cover:

1. Remove the meat drawer.

2. Push the cover back to release the rear clips from the shelf.

Tilt the cover up at the front, and pull it forward.

3. Replace the meat drawer cover by fitting the notches and

clips on the cover over the rear and center crossbars on the

shelf.

4. Lower cover into place and pull the cover forward to secure

the rear clips onto the shelf.

5. Replace the meat drawer.

NOTE: In some models the meat pan moves sideways on the

shelf to allow for flexible positioning.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish..................use same day as purchased

Chicken, ground beef, variety meats (liver) ...............1-2 days

Cold cuts, steaks/roasts ...........................................3-5 days

Cured meats............................................................7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

Crisper

(on some models)

Crisper Drawers

To remove and replace the crisper drawer:

1. Slide the crisper drawer straight out to the stop. Lift the front

and slide the drawer out the rest of the way.

2. Replace the drawer by sliding the drawer in fully past the

stop.

Crisper Cover

Style 1 - Plastic Cover

To remove and replace the crisper cover:

1. Remove the crisper(s).

2. Lift the front of the cover to remove the cover support. Then

lift the cover up and slide it out.

3. Replace the cover by fitting the cover tabs into lowest cabinet

slots and pushing them in. Lower the front retainers into

place.

Style 2 - Glass Cover

To remove and replace the crisper cover:

1. Pull the glass straight out.

2. Replace the glass by pushing it straight in.

Crisper Humidity Control (on some models)

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

■ Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store

in a loosely closed paper bag on a refrigerator shelf.

■ Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

■ Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

FREEZER FEATURES

Your model may have some or all of these features.

Wire Freezer Shelf

(on some models)

To remove and replace a wire shelf:

1. Remove the shelf by lifting the entire shelf slightly and moving

it all the way to the left-hand side. Tilt the right-hand side up

and out of the shelf supports.

2. Replace the shelf by inserting the left-hand end all the way

into the shelf supports. Then, lower the right-hand end of the

shelf and insert it into the shelf supports.

NOTE: The shelf should lower slightly and lock into place. If the

shelf does not appear stable, make sure both ends of the shelf

are inserted into the shelf supports.

Glass Freezer Shelf

(on some models)

To remove and replace a glass shelf:

1. Lift the front of the shelf to raise the shelf tabs up and out of

the opening in each shelf track. Slide the shelf out the rest of

the way.

2. Replace the shelf by tilting the back end downward to align

the back shelf tab under the track on each side of the freezer.

Gently push the shelf into the freezer until the two center shelf

tabs are positioned within the opening in each track. Lower

the shelf to rest on the shelf tracks.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Seal the package

or container securely to avoid taste and odor transfer throughout

the product. Ice crystals inside a sealed package are normal. This

simply means that moisture in the food and air inside the

package have condensed, creating ice crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 lbs of food per cubic foot [907 to

1,350 g per L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. The freezer door

must close tightly.

NOTE: For more information on preparing food for freezing,

check a freezer guide or reliable cookbook.

DOOR FEATURES

Your model may have some or all of these features.

Door Rails

The door rails may be removed for easier cleaning.

Snap on Door Rails (on some models)

To remove and replace the rails:

1. Remove the door rails by pushing in slightly on the front of

one end of the bracket while pulling out on the inside tab.

Repeat these steps for the other end.

2. Replace the rails by aligning the ends of the brackets with the

buttons on the sides of the door liner. Firmly snap bracket

and assembly onto the tabs above the shelf as shown.

Style 1 - Door Rails

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Style 2 - Trivets

Door Bins

(on some models)

To remove and replace the racks/bins:

1. Remove the rack/bin by lifting it and pulling it straight out.

2. Replace the rack/bin by sliding it in above the desired

support and pushing it down until it stops.

Utility Compartment and Can

Caddy

(on some models)

To remove and replace the utility compartment:

1. Remove the utility compartment by raising and holding the

cover up while lifting the utility compartment up and pulling it

straight out.

2. Replace the utility compartment by sliding it in above the

desired support and pushing it down until it stops.

To remove and replace the can caddy:

1. Hold the can caddy with one hand and pull up until it is

released from the door liner. Then, pull up on the caddy again,

until the stoppers have been overcome.

2. Pull the can caddy straight out to remove it from the door.

3. Replace the can caddy by aligning the grooves on the sides

with the pins in the door liner. Push up on the bottom of the

caddy until the stoppers have been overcome, and slide it

fully into the compartment.

Ice Maker

(on some models)

IMPORTANT: For models with a water filter, after connecting the

refrigerator to a water source or replacing the water filter, fill and

discard three full containers of ice to prepare the water filter for

use.

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

Ice Storage Bin

1. Wash the ice storage bin with mild soap and warm water.

2. Slide the ice storage bin under the ice maker, and push it

toward the back as far as it will go.

3. Lower the arm on the ice maker to the “on” position.

NOTE: It usually takes approximately 24 hours for the ice

maker to begin producing ice. You may notice the ice has an

“off-taste.” If so, discard the first three batches of ice

produced. After that the “off-taste” should be gone.

Ice Production Rate

■ The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period. Allow 3 days to completely fill the

ice container.

■ To increase ice production, lower the freezer and refrigerator

temperature. See “Using the Control(s).” Wait 24 hours

between adjustments.

Remember

■ The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot

be avoided, make sure the water softener is operating

properly and is well maintained.

■ Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice storage bin and the dispenser

mechanism.

■ Do not store anything on top of or in the ice maker or ice

storage bin.

Water Filtration System

Water Filter Status Light

The water filter status light will help you know when to change

your water filter.

■ When it is time to order a replacement water filter, the water

filter icon LED will light up whenever the refrigerator door is

open.

■ When it is time to replace the water filter, the water filter icon

LED will light up and flash whenever the refrigerator door is

open.

The disposable water filter should be replaced at least every

6 months, or sooner depending on your water quality and usage.

■ After changing the water filter, reset the status. Press and

hold the FILTERS RESET button for 3 seconds. When the

system is reset, the water filter icon LED will turn off.

Changing the Water Filter

1. Locate the water filter in the top-right corner of the

refrigerator compartment.

2. Lift open the filter cover door. The filter will be released and

then be ejected as the door is opened.

3. When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

4. Take the new filter out of its packaging and remove the

covers from the O-rings. Be sure the O-rings are still in place

after the covers are removed.

5. With the arrow pointing up, align the new filter with the filter

housing and slide it into place. The filter cover door will

automatically begin to close as the new filter is inserted.

6. Close the filter cover door completely in order to snap the

filter into place. You may need to press hard.

7. Make and discard three full containers of ice to prepare the

water filter for use, before using the ice.

REFRIGERATOR CARE

Cleaning

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT:

■ Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid

odor transfer and drying out of food, wrap or cover foods

tightly.

■ For stainless steel models, stainless steel is corrosion-

resistant and not corrosion-proof. To help avoid corrosion of

your stainless steel, keep your surfaces clean by using the

following cleaning instructions.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, muriatic acid,

cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on exterior surfaces (doors and

cabinet), plastic parts, interior and door liners or gaskets. Do not

use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Clean the exterior surfaces.

Painted metal: Wash painted metal exteriors with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately

to avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately

to avoid water spots.

NOTE: When cleaning stainless steel, always wipe in the

direction of the grain to avoid cross-grain scratching.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

■ Remove the base grille.

■ Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

■ Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

Changing the Light Bulbs

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with an appliance bulb of the same size, shape,

and wattage (no greater than 40 watts).

Style 1 - Electronic Control

The light bulbs are located at the top of the refrigerator

compartment.

1. Unplug refrigerator or disconnect power.

2. Using both hands, squeeze inward on the sides of the light

shield, releasing it from the back of the compartment. Then,

move the shield toward the back to release it from the front of

the compartment.

3. Remove the light bulb(s) and replace it with a 40 watt

appliance bulb of the same size and shape.

4. Replace the light shield by inserting the front end into the

compartment and then pushing up until it snaps into place.

5. Plug in refrigerator or reconnect power.

Style 2 - Dial Control

The light bulb is located behind the control.

1. Unplug refrigerator or disconnect power.

2. Remove the light shield by squeezing in on the sides and

pulling it straight down.

3. Remove the light bulb and replace it with a 40 watt appliance

bulb of the same size and shape.

4. Replace the light shield.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.maytag.com In Canada, www.maytag.ca

Refrigerator Operation

The refrigerator will not operate

■ Power cord unplugged? Plug into a grounded 3 prong

outlet.

■ Is outlet working? Plug in a lamp to see if the outlet is

working.

■ Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

■ Control(s) on? Make sure the refrigerator control is on. See

“Using the Control(s).”

■ New installation? Allow 24 hours following installation for

the refrigerator to cool completely.

NOTE: Adjusting the temperature control(s) to coldest setting

will not cool the refrigerator more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, the door is

opened often, or if the door has been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below

are listed some normal sounds with explanations.

■ Buzzing - heard when the water valve opens to fill the ice

maker

■ Pulsating - fans/compressor adjusting to optimize

performance.

■ Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator.

■ Sizzling/Gurgling - water dripping on the heater during

defrost cycle

■ Popping - contraction/expansion of inside walls, especially

during initial cool-down.

■ Water running/dripping - may be heard when ice melts

during defrosting and water runs into the drain pan.

■ Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

The doors will not close completely or they pop open

■ Door blocked open? Move food packages away from door.

■ Bin or shelf in the way? Push bin or shelf back in the correct

position.

■ Crisper cover in the way? Make sure the crisper cover is

fully pushed in, so that the back rests on the supports.

■ Refrigerator not tilted toward the rear? So the doors will

close easier, raise the front of the refrigerator so that it tilts

slightly downward toward the rear. See “Adjust the Doors.”

■ Door closed too quickly? Close the door slowly and firmly to

keep the door from popping open.

The door is difficult to open

■ Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

Temperature and Moisture

Temperature is too warm

■ New installation? Allow 24 hours following installation for

the refrigerator to cool completely.

■ Door opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep door fully

closed.

■ Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

■ Control(s) set correctly for the surrounding conditions?

Adjust the control(s) a setting colder. Check temperature in

24 hours. See “Using the Control(s).”

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

■ Humid room? Contributes to moisture buildup.

■ Door opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep door fully

closed.

Ice and Water

The ice maker is not producing ice or not enough ice

■ Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

■ Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

■ Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

■ New installation? Wait 24 hours after ice maker installation

for ice production to begin. Allow 3 days to completely fill the

ice container.

■ Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

■ Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

■ Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See “Water Supply Requirements.”

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

■ Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

■ Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

■ Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See “Water Supply Requirements.”

■ Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

■ New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

■ Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

■ Odor transfer from food? Use airtight, moisture proof

packaging to store food.

■ Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

ACCESSORIES

The following accessories are available for your refrigerator. To

order, contact us and ask for the part numbers.

In the U.S.A., visit www.maytag.com/accessories or call

1-800-901-2042

In Canada, visit www.whirlpoolparts.ca or call 1-800-807-6777

affresh

Stainless Steel Cleaner:

In U.S.A., order Part #W10355016

In Canada, order Part #W10355016B

affresh

Stainless Steel Wipes:

In U.S.A., order Part #W10355049

In Canada, order Part #W10355049B

affresh

Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010

In Canada, order Part #W10355010B

Water Filter:

Order Part #W10295370 or FILTER1

Air Filter:

Order Part #W10311524 or AIR1

Ethylene Filter:

Order Part # W10346771A or FRESH1

Water Filter and Air Filter Bundle Pack:

Order Part # W10355212BL

Water Filter, Air Filter and Ethylene Filter Bundle Pack:

Order Part # W10365758BL

Reversibility Kit:

Order Part # W10395149

WATER FILTER

CERTIFICATIONS

PERFORMANCE DATA SHEET

Water Filtration System

Model P5WB12NL/P4RFWB12 Capacity 120 Gallons (455 Liters)

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).

Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 120 gallons (455 liters).

■ It is important that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised. Property damage can occur if all

instructions are not followed.

■ Use replacement filter P4RRWB/P4RFWB12, part

#W10295370. 2012 suggested retail price of $49.99 U.S.A./

$59.99 Canada. Prices are subject to change without notice.

Style 1 – When the water filter status display changes from

“GOOD” to “ORDER,” order a new filter. When the filter

indicator reads “REPLACE,” it is recommended that you

replace the filter.

Style 2 – When the filter indicator changes from green to

yellow, order a new filter. When the indicator changes from

yellow to red, it is recommended that you replace the filter.

Style 3 – When the filter indicator reads 10%, order a new

filter. When the indicator reads 0%, it is recommended that

you replace the filter.

Style 4 – For models without a water dispenser, replace the

disposable water filter every 6 months. The water filter

indicator light will remind you when it is time to change the

water filter.

■ After changing the water filter, flush the water system. For

filtered ice only, make and discard three full containers of ice

to prepare the water filter for use.

■ These contaminants are not necessarily in your water supply.

While testing was performed under standard laboratory

conditions, actual performance may vary.

■ The product is for cold water use only.

■ The water system must be installed in compliance with state

and local laws and regulations.

■ Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

■ Refer to the “Warranty” section for the Manufacturer’s name,

address and telephone number.

■ Refer to the “Warranty” section for the Manufacturer’s limited

warranty.

Application Guidelines/Water Supply Parameters

System tested and certified by NSF International against NSF/ANSI

Standard 42 for the reduction of Chlorine Taste and Odor, and Particulate

Class I*; and against NSF/ANSI Standard 53 for the reduction of Live

Cysts, Asbestos, Lead, Lindane, Toxaphene, Atrazine, and 2,4 - D.

Substance Reduction

Aesthetic Effects

NSF Reduction

Requirements

Average

Influent

Influent Challenge

Concentration

Maximum

Effluent

Minimum %

Reduction

Average %

Reduction

Chlorine Taste/Odor

Particulate Class I

50% reduction

85% reduction

2.0 mg/L

7,300,000 #/mL

2.0 mg/L ± 10%

At least 10,000 particles/mL

0.20 mg/L

75,000 #/mL

97.2

99.4

Contaminant

Reduction

NSF Reduction

Requirements

Average

Influent

Influent Challenge

Concentration

Maximum

Effluent

Minimum %

Reduction

Average %

Reduction

Live Cysts

†

99.95% 160,000/L 50,000/L min. 54/L

†

99.97 99.99

Asbestos 99% 87 MFL 10

to 10

fibers/L

††

0.17 MFL 99 99

Lead: @ pH 6.5

Lead: @ pH 8.5

0.010 mg/L

0.160 mg/L

0.140 mg/L

0.15 mg/L ± 10%

0.001 mg/L

0.005 mg/L

99.4

98.6

99.4

98.6

Lindane 0.0002 mg/L 0.0019 mg/L 0.002 mg/L ± 10% 0.00002 mg/L 98.9 99

Toxaphene 0.003 mg/L 0.014 mg/L 0.015 mg/L ± 10% 0.001 mg/L 93 93

Atrazine 0.003 mg/L 0.0094 mg/L 0.009 mg/L ± 10% 0.0005 mg/L 94.5 94.7

2,4 - D 0.07 mg/L 0.220 mg/L 0.210 mg/L ± 10% 0.028 mg/L 87.5 96.1

Water Supply

Water Pressure

Water Temperature

Service Flow Rate

City or Well

30 - 120 psi (207 - 827 kPa)

33° - 100°F (0.6° - 37.8°C)

0.5 gpm (1.9 Lpm) @ 60 psi

†

††

Class I particle size: >0.5 to <1 um

Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

Based on the use of Cryptosporidium parvum oocysts

Fibers greater than 10 um in length

® NSF is a registered trademark of NSF International.

MAYTAG

MAJOR APPLIANCE WARRANTY

The one year limited warranty, shown below, is for Model M1TXEGMY only. For all other model numbers, please see the

warranty information on the following page.

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated and maintained according to instructions

attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “Maytag”) will pay

for factory specified replacement parts and repair labor to correct defects in materials or workmanship that existed when this major

appliance was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THE LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a Maytag designated service company. This limited warranty is valid in the United States or Canada and

applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective from the date

of the original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Maytag.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.

6. Any food or medicine loss due to refrigerator or freezer product failures.

7. Pickup and delivery. This major appliance is intended to be repaired in your home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Maytag servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Maytag's published installation instructions.

11. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or

cannot be easily determined.

12. Discoloration, rust, or oxidation of stainless steel surfaces.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Maytag or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the

exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty

gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies. 2/11

MAYTAG

REFRIGERATION LIMITED WARRANTY

This warranty does not apply to Model M1TXEGMY; see warranty information on previous page for this model.

FIRST YEAR LIMITED WARRANTY (PARTS AND LABOR)

For one year from the date of purchase, when this major appliance is installed, operated and maintained according to instructions

attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada, LP (hereafter “Maytag”) will pay

for factory specified replacement parts and repair labor to correct defects in materials or workmanship that existed when this major

appliance was purchased.

SECOND THROUGH TENTH YEAR LIMITED WARRANTY (COMPRESSOR ONLY - LABOR NOT INCLUDED)

In the second through tenth years from the date of original purchase, when this major appliance is installed, operated and maintained

according to instructions attached to or furnished with the product, Maytag will pay for a factory specified replacement compressor to

correct non-cosmetic defects in materials or workmanship in this part that prevent function of the refrigerator and that existed when this

major appliance was purchased. This limited 10-year warranty is for the compressor only and does not include labor.