Faber Cristal 30 SS 400 cfm Guía de instalación

Faber
Marca
Faber
Modelo
Cristal 30 SS 400 cfm
Categoría
Campanas de cocina
Tipo
Guía de instalación

Este manual también es adecuado para

CRIS36SS300 CRIS36SS400 CRIS36SS600
CRIS30SS300 CRIS30SS400 CRIS30SS600
Installation Instructions
Use and Care Information
Instructions d'installation
Utilisez et d'entretien
Instrucciones de instalación
Información de uso y cuidado
NEW CRISTAL
Version 06/14 - Page 1
READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD
WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. b) Always turn
hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Pepper-corn Beef Flambé). c)
Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. d) Use proper pan size. Always use
cookware appropriate for the size of the surface element.
WARNING:aBased on “Kitchen Firesafety Tips” published by NFPA. - TO REDUCE THE RISK OF INJURY TO PERSONS
IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING: SMOTHER FLAMES with a close-fitting
lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go
out immediately EVACUATE AND CALL THE FIRE DEPARTMENT. NEVER PICK UP A FLAMING PAN - You may be
burned. DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result. Use an
extinguisher ONLY if: 1. You know you have a Class ABC extinguisher, and you already know how to operate it. 2. The fire is
small and contained in the area where it started. 3. The fire department is being called. 4. You can fight the fire with your back to
an exit.
ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST BE SEALED.
This rangehood requires at least 24" of clearance between the bottom of the rangehood and the cooking surface or countertop.
This minimum clearance may be higher depending on local building code. For example, for gas ranges, a minimum of 30"
may be required. Overhead cabinets on both sides of this unit must be a minimum of 24" above the cooking surface or
countertop. Consult the cooktop or range installation instructions given by the manufacturer before making any cutouts.
MOBILE HOME INSTALLATION The installation of this rangehood must conform to the Manufactured Home Construction and
Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard for Mobile Home Construction and Safety, Title 24, HUD,
Part 280). Four wire power supply must be used and the appliance wiring must be revised. See Electrical Requirements.
LISEZ BIEN CETTE FICHE AVANT D'INSTALLER LA HOTTE
AVERTISSEMENT - POUR MINIMISER LE RISQUE D’UN FEU DE GRAISSE SUR LA TABLE DE CUISSON : a) Ne jamais
laisser un élément de la table de cuisson fonctionner sans surveillance à la puissance de chauffage maximale; un renversement/
débordement de matière graisseuse pourrait provoquer une inflammation et le génération de fumée. Utiliser toujours une puissance
de chauffage moyenne ou basse pour le chauffage d’huile. b) Veiller à toujours faire fonctionner le ventilateur de la hotte lors d’une
cuisson avec une puissance de chauffage élevée ou lors de la cuisson d’un mets à flamber (i.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flambé). c) Nettoyer fréquemment les ventilateurs d’extraction. Veiller à ne pas laisser de la graisse s’accumuler
sur les surfaces du ventilateur ou des filtres. d) Utiliser toujours un ustensile de taille appropriée. Utiliser toujours un ustensile de
taille adapté à la taille de l’élément chauffant.
AVERTISSEMENT:Basé sur "Kitchen Firesafety Tips" publié par NFPA. - POUR PRÉVENIR LES BLESSURES EN CAS
DE FEU SUIVRE LES RECOMMANDATIONS SUIVANTES: ÉTOUFFEZ LE FEU avec un couvercle métallique et fermez le
brûleur. Si le feu ne s'éteint pas tout de suite, QUITTEZ LES LIEUX ET APPELEZ LES POMPIERS. NE TOUCHEZ
JAMAIS UNE CASSEROLE EN FLAMMES. N'UTILISEZ JAMAIS DE L'EAU ou un torchon mouillé pour éteindre le feu -
ce qui pourrait causer une explosion de vapeur. N'utilisez un extincteur que si: 1. Vous avez un modèle ABC et vous
connaissez bien son mode d'emploi. 2. Le feu est petit et peu répandu. 3. Les pompiers sont déjà prévenus. 4. Vous avez une
sortie derrière vous.
TOUTE OUVERTURE DANS LE MUR OU LE PLANCHER À PROXIMITÉ DE LA HOTTE DOIT ÊTRE SCELLÉ
Gardez 24 po. de hauteur entre le bas de la hotte et la surface de cuisson. Cette hauteur minimum peut être plus haute suivant le
code municipal. Par exemple, les cuisinières à gaz peuvent requérir 30 po. de hauteur. Les armoires au-dessus de chaque
côté devront être au moins à 24 po. au-dessus de la surface de cuisson. Consultez la fiche technique avant de découper les
armoires. L'installation de cette hotte doit être conforme aux Réglements de Manufactured Home Construction and Safety
Standards, titre 24 CFR, Section 3280 (anciennement Federal Standard for Mobile Home Construction and Safety Standards,
titre 24 CFR, Section 3280 (anciennement Federal Standard for Mobile Home Construction and Safety, titre 24, HUD, Section
280). Le branchement électrique se fait avec une raccordement à 4 fils. Consultez la fiche technique électrique.
CRISTAL HC SS - Halogen
Stainless Slideout Rangehood
• Installation Instructions
• Use and Care Information
READ AND SAVE THESE INSTRUCTIONS
The Installer must leave these instructions with the homeowner.
The homeowner must keep these instructions for future reference
and for local electrical inspectors' use.
CAUTION:- TToo rreedduuccee rriisskk ooff ffiirree aanndd ttoo pprrooppeerrllyy eexxhhaauusstt aaiirr,, bbee ssuurree ttoo dduucctt aaiirr oouuttssiiddee –– DDoo nnoott vveenntt eexxhhaauusstt aaiirr iinnttoo ssppaacceess
wwiitthhiinn wwaallllss oorr cceeiilliinnggss oorr iinnttoo aattttiiccss,, ccrraawwll ssppaacceess,, oorr ggaarraaggeess..
PRUDENCE:- -- AAffiinn ddee rréédduuiirree lleess rriissqquueess dd''iinncceennddiiee aassssuurreezz--vvoouuss qquuee ll''aaiirr ssooiitt ccoorrrreecctteemmeenntt éévvaaccuuéé àà ll''eexxttéérriieeuurr.. LL''aaiirr nnee ddooiitt ppaass êêttrree
éévvaaccuuéé ddaannss lleess eessppaacceess lliibbrreess eennttrree lleess ppaarrooiiss oouu ffaauuxx ppllaaffoonnddss,, aauuvveennttss,, ggaarraaggeess..
2
READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START
INSTALLING THIS RANGEHOOD
WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause smoking and
greasy spillovers that may ignite. Heat oils slowly on low or medium setting.
b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes
Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan
orlter.
d) Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.
BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE
AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will
result.
d) Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. Thereissmallandcontainedintheareawhereitstarted.
3. Theredepartmentisbeingcalled.
4. Youcanghttherewithyourbacktoanexit.
* Based on "Kitchen Firesafety Tips" published by NFPA
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this
fan with any solid-state speed control device.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have any
questions, contact the manufacturer.
2. Before servicing or cleaning unit, switch power off at service panel and lock the
service disconnecting means to prevent power from being switched on acciden-
tally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or
Explosive Materials and Vapors.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-
dance With All Applicable Codes And Standards, Including Fire-Rated Construction.
2. Sufcientairisneededforpropercombustionandexhaustingofgasesthrough
theue(chimney)offuelburningequipmenttopreventbackdrafting.Followthe
heating equipment manufacturer's guideline and safety standards such as those
publishedbythe National Fire ProtectionAssociation (NFPA),andthe American
SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and
the local code authorities.
3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and
other hidden utilities.
4. Ducted fans must always be vented to the outdoors.
3
ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST
BE SEALED.
This rangehood requires at least 24" of clearance between the bottom of the rangehood
and the cooking surface or countertop. This hood has been approved by UL at this distance
from the cooktop.
This minimum clearance may be higher depending on local building codes. For gas cooktops
and combination ranges, a minimum of 30" is recommended and may be required.
Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface
or countertop. Consult the cooktop or range installation instructions given by the manufacturer
before making any cutouts.
MOBILE HOME INSTALLATION The installation of this rangehood must conform to the
Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly
Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See
Electrical Requirements.
• Venting system MUST terminate outside the home.
• DO NOT terminate the ductwork in an attic or other enclosed space.
• DO NOT use 4" laundry-type wall caps.
• Flexible-type ductwork is not recommended.
• DO NOT obstruct the ow of combustion and ventilation air.
• Failure to follow venting requirements may result in a re.
WARNING
!
VENTING REQUIREMENTS
Determine which venting method is best for your application. Ductwork can extend either through the
wall or the roof.
The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient
performance. The size of the ductwork should be uniform. Do not install two elbows together. Use
duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening
around the cap.
Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence
that greatly reduces performance.
Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.
Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting
frame must be constructed.
WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.
CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do
not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.
Cold Weather installations
An additional back draft damper should be installed to minimize backward cold air ow and a
nonmetallic thermal break should be installed to minimize conduction of outside temperatures as
part of the vent system. The damper should be on the cold air side of the thermal break. The break
should be as close as possible to where the vent system enters the heated portion of the house.
4
• Electrical ground is required on this rangehood.
• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO
NOT use for grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or
grounding circuit could result in electrical shock.
• Check with a qualied electrician if you are in doubt as to whether the rangehood is
properly grounded.
• Failure to follow electrical requirements may result in a re.
WARNING
!
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-delay
fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with
the electrical rating of this unit as specied on the serial/rating plate located inside the unit near the eld
wiring compartment.
5
Version 06/14 - Page 4
CUT-OUT
CRISTAL HC DIMENSIONS
FRONT TRIM OPTIONS
The Cristal HC comes with a stainless steel front strip installed. Optional black and white kits are available for purchase.
For a custom front strip, a local cabinet shop can make a strip to match your cabinets.
CUSTOM FRONT TRIM DIMENSIONS
1 15/32"
3/4"
29 7/8" or 35 7/8"
25 1/2” - 31 1/2”
10”
25 1/2” - 31 1/2”
13/16”
17 1/2” - 23 1/2”
5 7/8”
Pre-Planning Your Installation -
Important: The recommended height to install this hood
off the cooktop is a minimum of 24" and a maximum of 30” for maximum effectiveness. Also
consult the cooktop manufacturer’s recommendation. NOTE: If direct rear venting, use the side
dimensional diagram below on the right. For top venting (comes standard in this position),
use the left dimensional diagram. Refer to page 5 for directions for direct rear venting.
3 15/16”
CRISTAL HC SIDE DIMENSIONS
(TOP VENT - STANDARD)
CRISTAL HC SIDE DIMENSIONS
(DIRECT REAR VENT OPTION)
3 15/16”
6
36" RANGEHOOD REAR INFORMATION
30" RANGEHOOD REAR INFORMATION
DRAFT 25-MAY-2020 18:52
Palazzi, Walter
15-Nov-2019
Released
= =
DRAFT 25-MAY-2020 18:52
DRAFT 25-MAY-2020 18:52
7
Version 06/14 - Page 5
9.0 feet
10.0 feet
0.0 feet
19.0 feet
TOOLS NEEDED FOR INSTALLATION
• Saber Saw or Jig Saw
• Drill
• 1 1/4" Wood Drill Bit
• Pliers
• Phillips Screwdriver
• Wire Stripper or Utility Knife
• Metal Snips
• Measuring Tape or Ruler
• Level
• Pencil
• Caulking Gun
• Duct Tape
PARTS SUPPLIED FOR INSTALLATION
• 1 Backdraft Damper
• 1 Vent Grate (for recirculating installations only)
• 1 Vinyl Trim
• 1 Literature Package
PARTS NEEDED FOR INSTALLATION
• 2 Conduit Connectors
• Power Supply Cable
• 1 Wall or Roof Cap
• All Metal Ductwork
PLAN THE DUCTWORK
The Cristal HC slideout rangehood is designed to offer wide exibility of installations.
The rangehood can be ducted vertically or horizontally through a 6" round vent.
The unit can also be installed in a recirculating conguration. The unit comes
standard in the top venting position. FIGURES 1 and 2 show vertical and horizontal
installations for this unit. FIGURE 3 shows recirculating installation.
The Cristal HC requires 6" round ductwork. To ensure that the blower performs to
its highest possible capacity, ductwork should be as short and straight as possilbe.
RECIRCULATING INSTALLATIONS
For recirculating installations (FIGURE 3), Charcoal Filters are necessary. Remove all four grease lters and set aside. Attach
one charcoal lter to each end of the blower. Each charcoal lter attaches to the black grid on the side of the blower. Rotate
the lter clockwise to install and counterclockwise to remove (FIGURE 3A). Replace all four grease lters. Some ductwork
must be installed to exhaust the rangehood back into the kitchen, either at the top of the cabinet or at the face of the soft. A
plastic vent grate (FIGURE 3B) supplied with the rangehood can be used to cover the duct opening. This duct work must not
terminate into a dead air space.
FIGURE 3A
45˚ Elbow
90˚ Elbow
90˚ Flat Elbow
Wall Cap
FIGURE A
9 Feet Straight Duct
2 - 90˚ Elbows
Wall Cap
Total System
FIGURE B
3.0 feet
5.0 feet
12.0 feet
0.0 feet
VERTICAL
DUCTING
FIGURE 2
HORIZONTAL
DUCTING
FIGURE 1
For direct rear venting (FIGURE 2), you must
change the blower position. Remove the 12
screws that hold the metal housing to the
rangehood body. Remove the 4 screws that
hold the blower housing to the metal housing.
Rotate the blower 90 degrees toward the back
and then ip it over 180 degrees. Be sure that
the power supply cable is properly positioned.
Replace all screws, making sure that they are
rmly fastened.
cabinet
ceiling
6” round
duct
hood
cabinet
ceiling
6” round
duct
hood
soft
vent grate
vent grate
FIGURE 3B
FIGURE 3
For satisfactory performance the duct run should
not exceed 50 equivalent feet if ducted using the
required minimum 6" round duct. The equivalent
feet in FIGURE A for each piece of duct in the
system An example is given in FIGURE B. For
best results, use no more than three 90°
elbows. Make sure that there is a minimum of
24" of straight duct between elbows if more
than one is used. Do not install two elbows
together. If you must elbow right away, do it
as far away from the hood's exhaust opening
as possible.
8
Version 06/14 - Page 6
OPTIONAL ACCESSORIES FOR PURCHASE SEPARATELY
ACCESSOIRES EN OPTION POUR ACHETER SÉPARÉMENT
• Charcoal Filters
For non-vented installations only, replace charcoal
lters as needed part # FILTER1
• CFM Reducer Kit
To reduce cfm to below 300 cfm for use in
make up air environments part # CFMRED
• Universal Make Up Air Damper 6"
Brings fresh air back into the home thru an automatic
damper when the hood is on #MUDAMPER6
• Universal Make Up Air Damper 8"
Brings fresh air back into the home thru an automatic
damper when the hood is on #MUDAMPER8
• Front Trim Kits
Replace stainless trim on the slide out hood with a
black or white trim (available in 30" or 36")
CRTRIM30WH (30" white)
CRTRIM30BK (30" black)
CRTRIM36WH (36" white)
CRTRIM36BK (36" black)
• Filtres à charbon
Pour les installations non ventilé seulement, rem-
placer le charbon de bois
ltres au besoin partie # FILTER1
• Réducteur de CFM Kit
Pour réduire cfm à 300 cfm ci-dessous pour une
utilisation dans
compenser milieux aériens partie # CFMRED
• Universal Make Up registre d'air 6"
Apporte de l'air frais de nouveau dans la maison à
travers un amortisseur automatique lorsque le capot
est sur # MUDAMPER6
• Universal Make Up Air Amortisseur 8"
Apporte de l'air frais de nouveau dans la maison à
travers un amortisseur automatique lorsque le capot
est sur # MUDAMPER8
• Front Bordure Kits
Remplacer la garniture inoxydable sur la diapositive
sur le capot avec un
équilibre noir ou blanc (disponible en 30 "ou 36")
CRTRIM30WH (30 "blanc)
CRTRIM30BK (30 "noir)
CRTRIM36WH (36 "blanc)
CRTRIM36BK (36 "noir)
"When used in recirculation mode, to Reduce the Risk of
Fire and Shock use only conversion kit Model FILTER 1 -
FILTER1LL"
Version 06/14 - Page 6
OPTIONAL ACCESSORIES FOR PURCHASE SEPARATELY
ACCESSOIRES EN OPTION POUR ACHETER SÉPARÉMENT
• Charcoal Filters
For non-vented installations only, replace charcoal
lters as needed part # FILTER1
• CFM Reducer Kit
To reduce cfm to below 300 cfm for use in
make up air environments part # CFMRED
• Universal Make Up Air Damper 6"
Brings fresh air back into the home thru an automatic
damper when the hood is on #MUDAMPER6
• Universal Make Up Air Damper 8"
Brings fresh air back into the home thru an automatic
damper when the hood is on #MUDAMPER8
• Front Trim Kits
Replace stainless trim on the slide out hood with a
black or white trim (available in 30" or 36")
CRTRIM30WH (30" white)
CRTRIM30BK (30" black)
CRTRIM36WH (36" white)
CRTRIM36BK (36" black)
• Filtres à charbon
Pour les installations non ventilé seulement, rem-
placer le charbon de bois
ltres au besoin partie # FILTER1
• Réducteur de CFM Kit
Pour réduire cfm à 300 cfm ci-dessous pour une
utilisation dans
compenser milieux aériens partie # CFMRED
• Universal Make Up registre d'air 6"
Apporte de l'air frais de nouveau dans la maison à
travers un amortisseur automatique lorsque le capot
est sur # MUDAMPER6
• Universal Make Up Air Amortisseur 8"
Apporte de l'air frais de nouveau dans la maison à
travers un amortisseur automatique lorsque le capot
est sur # MUDAMPER8
• Front Bordure Kits
Remplacer la garniture inoxydable sur la diapositive
sur le capot avec un
équilibre noir ou blanc (disponible en 30 "ou 36")
CRTRIM30WH (30 "blanc)
CRTRIM30BK (30 "noir)
CRTRIM36WH (36 "blanc)
CRTRIM36BK (36 "noir)
- # FILTER1LL
- # FILTER1LL
9
Version 06/14 - Page 7
INSTALL THE RANGEHOOD
1. Remove the rangehood from the carton and place on a
flat surface. Cover the surface to prevent accidental damage.
Remove all parts including the backdraft damper, plastic grille
and literature package before discarding the carton. Remove
the grease filters and set aside.
FIGURE 5
2. The rangehood mounts to the cabinet by two spring loaded
brackets, one on each side of the rangehood (FIGURE 6). Lift
the rangehood into the cutout opening in the cabinet. Be careful
not to damage the cabinet, rangehood or other appliances.
CUT-OUT
PREPARE THE CABINET
1. Disconnect and move freestanding range from cabinet
opening to provide easier access to upper cabinet and rear wall.
Put a thick, protective covering over cooktops, set-in ranges or
countertops to protect from damage or dirt.
2. Determine and clearly mark with a pencil the center line
of the cabinet on the wall and on the underside of the cabinet
where the rangehood will be installed.
3. If the cabinet bottom is recessed, wood blocks need to
be installed to insure proper alignment with the cabinet bottom.
Wood blocks should be ush or recessed 1/16" to 1/8" within
the cabinet bottom as indicated in FIGURE 4.
FIGURE 4
MAKE THE CUT-OUT OPENING (FIGURE 5)
WHERE THE RANGEHOOD WILL BE INSTALLED.
4. Determine the proper cutouts for the ductwork. Make all
necessary cuts in the walls or cabinets for the ductwork. Install
the ductwork before mounting the rangehood.
5. Determine and make the proper cutout for the Power Supply
Cable. Use a 1 1/4" Drill Bit to make this hole. Run the Power
Supply Cable through the wall or cabinet. DO NOT turn on the
power until installation is complete. Use caulking to seal around
the wire opening.
FIGURE 6
3.The spring loaded brackets are factory set to accomo-
date a thickness between 1 3/16" and 2 1/4". If your cabinet
bottom is less than 1 3/16" thick, the spring loaded brackets
can be removed and repositioned down from the top setting
to the bottom setting by removing the four phillips screws.
4. Tighten the rangehood to the cabinet by rotating the
screws with a phillips screw driver.
5. A grey vinyl strip (FIGURE 7) is included to cover the
underside of any remaining exposed cabinet. Attach the grey
vinyl strip to the bottom of the back of the rangehood with the
three screws provided. If necessary, the strip can be cut to
fit the cabinet depth.
7. Remove the cover from the eld wiring compartment with
a phillips screwdriver. Feed the Power Supply Cable through
the electrical knockout. Connect the Power Supply Cable to the
rangehood cable. Attach the White lead of the power supply
to the White lead of the rangehood with a twist-on type wire
connector. Attach the Black lead of the power supply to the
Black lead of the rangehood with a twist-on type wire connector.
Attach the Power Supply Cable grounding lead to the green
screw provided. Using the 4 holes provided, screw the eld
wiring compartment to the wall or cabinet as dictated by your
Power Supply Cable location (screws not provided). Replace
the cover.
8. Replace the grease lters. Connect the ductwork to the
damper and seal all connections.
9. Turn the power supply on. Turn on the blower and light.
If the rangehood does not operate, check that the circuit breaker
is not tripped or the house fuse blown. If the unit still does
not operate, disconnect the power supply and check that the
wiring connections have been made properly.
FIGURE 7
VINYL STRIP
25 1/2” - 31 1/2”
10”
25 1/2” - 31 1/2”
13/16”
17 1/2” - 23 1/2”
5 7/8”
Only for Ducted Venting Installation
Install the 2 Damper Flap included with the Range
Hood as shown.
10
7
Direct Connect Wiring Box
Accessory sku # WIREBOX
(purchased separately)
Created by
-
Denomination
-
Lang EN Sheet
1
/1
Modif.by
Approved by
Approval date
Doc. status
Drawing N.
NEW_DRAWING_BOX
Rev
01
ELECTRICAL INSTALLATION WITH OPTIONAL
WIRING BOX
For Permanent wiring Installation-Use only with Listed
rangehood Wiring Box kit
sku # WIREBOX, manufactured by Faber.
Max. 33 7/16”
GROUNDING INSTRUCTIONS This appliance must be grounded.
In the event of an electrical short circuit, grounding reduces the risk
of electric shock by providing an escape wire for the electric current.
This appliance is equipped with a cord having a grounding wire with
a grounding plug. The plug must be plugged into an outlet that is
properly installed and grounded.
WARNING - Improper grounding can result in a risk of electric shock.
Consult a qualied electrician if the grounding instructions are not
completely understood, or if doubt exists as to whether the appliance
is properly grounded.
Do not use an extension cord. If the power supply cord is too short,
have a qualied electrician install an outlet near the appliance.
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/O Switch
TheOn/O switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light o.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower o.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut o when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is o, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The New Cristal comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
FIGURE 8
1
15/32"
FIGURE 9
3/4"
29
7/8"
or 35
7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
ELECTRICAL INSTALLATION
WITH CONNECTION CABLE
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/O Switch
TheOn/O switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light o.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower o.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut o when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is o, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The New Cristal comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
FIGURE 8
1 15/32"
FIGURE 9
3/4"
29 7/8" or 35 7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/O Switch
TheOn/O switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light o.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower o.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut o when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is o, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The New Cristal comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
FIGURE 8
1
15/32"
FIGURE 9
3/4"
29
7/8"
or 35
7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/O Switch
TheOn/O switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light o.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower o.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut o when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is o, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The New Cristal comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
FIGURE 8
1
15/32"
FIGURE 9
3/4"
29
7/8"
or 35
7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/O Switch
TheOn/O switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light o.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower o.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut o when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is o, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The New Cristal comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
FIGURE 8
1
15/32"
FIGURE 9
3/4"
29
7/8"
or 35
7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
11
USE AND CARE INFORMATION
For Best Results
Start the rangehood several minutes before cooking to develop proper airow. Allow the
rangehood to operate for several minutes after cooking is complete to clear all smoke and
odors from the kitchen.
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/Off Switch
TheOn/Off switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light off.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower off.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut off when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
proper airow. Allow the unit to operate for several minutes
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
The metal grease lters should be cleaned frequently in hot
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
agents can scratch rangehood nishes and should not be
used to clean nished surfaces.
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is off, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The Cristal HC comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9.
FIGURE 8
1 15/32"
FIGURE 9
3/4"
29 7/8" or 35 7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/Off Switch
TheOn/Off switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light off.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower off.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut off when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
proper airow. Allow the unit to operate for several minutes
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
The metal grease lters should be cleaned frequently in hot
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
agents can scratch rangehood nishes and should not be
used to clean nished surfaces.
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is off, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The Cristal HC comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9.
FIGURE 8
1 15/32"
FIGURE 9
3/4"
29 7/8" or 35 7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
12
Cleaningmetalgreaselters
The metal grease lters can be cleaned in hot detergent solution or
washed in the dishwasher. They should be cleaned every 2 months
use, or more frequently if use is particularly heavy.
• Open the visor by pulling it.
• Remove the lter, pushing the lever towards the back of the unit and
at the same time pulling downward.
• Wash the lter without bending it, leave it to dry thoroughly before
replacing (if the surface of the lter changes color over time, this will
have absolutely no effect on its efciency).
• Replace, taking care to ensure that the handle faces forward.
• Cleaning in dishwasher may dull the nish of the metal grease
lter.
• Close
the visor.
Replacing Activated Charcoal Filter
The Activated Charcoal Filters are not washable and cannot
be regenerated, and must be replaced approximately every 4
months of operation, or more frequently with heavy usage.
• Open the visor by pulling it.
• Remove the Filter, pushing it towards the back of the unit and at the same
time pulling downward.
• Remove the saturated Activated Charcoal Filters, as indicated (A).
• Fit the new Filters, as indicated (B).
• Replace, taking care to ensure that the handle faces forwards.
• Close
the visor.
EN 7
7
INSTALLATION
Fitting the Hood canopy
BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:
• Disconnect the wires to the Commands at the connectors.
• Disconnect the wires to the Light at the con-
nectors.
• The Hood can be installed directly on the
underside of the wall unit (Minimum 650 mm
from the Cooker Hob).
• Create an opening in the bottom of the wall unit,
as shown.
• Insert the hood until the side supports snap into
place.
• Fasten using the 10 screws 12a provided.
• Lock in position by tightening the screws Vf from
underneath the hood.
• Open the suction panel by turning the specific knob.
• Disconnect the panel from the hood canopy by sliding the
fixing pin lever.
• Remove grease filters.
• Screw the Frame into place
using the 6 screws 12f, re-
connect the wires to the
Commands and Light, re-
place the metal grease filter
and the Panel.
260
13
495 - 675
Gu10 self-ballasted led
lamps – listed in ac-
cordance with
ul 1993/nmx-
j-578/1-ance/
csa c22.2 No.
1993
Lighting unit
• Turn off electrical supply before replacing bulbs, and
make sure bulbs are cool to touch before proceeding.
• Remove the lamp at the base and turn slightly to the
left and the pull out from the connector and turn slightly
to the left.
• Replace the lamp with a new one of the same type,
making sure that you insert the two pins properly into
the housings on the lamp holder.
• Once the bulb pins are in place turn slightly to the right
to secure.
13
Wiring Diagram
0123456789
R
P
P
H90_496 01
Drawing N : Rev :
Modif. by
Doc.status
Do not get quotas from the drawing do not bring
modifications without authorization of techincal office.
According to the law we reserve the own of the present
drawing with reproduction prohibition partial or total.
Approved date
Modification description
Approved by
WIRING DIAGRAM M8_4V SCL HV LED
Doc Type
Denomination
Creation date
02.Mar.2018
DOLCE CORRADO
Created by
991.0520.839
Code
LED
0
1
SW3
LED
RV
CN3
RED (org)
VLT(org)
LB WH A GR
CN2
WHT
WHT
BRW
BLU
0 1 2 3
SW2
RED
123
654
789
PNK
BLU
PNK
BK BR
CN1
RED
BRW
SIDE
INSERT
CABLE
SW1
BLK
123
654
987
PNK
M8-4V
BRW
ORG
M1
WHT
BLU
BLK
GRY
6,3uF
Y-G
WHT
220-240V ~ 50Hz
110-127V ~ 60Hz
220 ~ 60Hz
Y-G
BLK
14
WARRANTY
Franke Home Solutions Warranty for Franke and Faber Branded Product
Effective March 1, 2022
In the United States, Canada and Latin America, Franke warrants the Faber branded products from manufacturing defects
in material and workmanship when purchased from a Franke or Faber Authorized Retailer pursuant to product-specific
warranties detailed herein (each, a “Warranty” and collectively, the “Warranties”). The products must be properly installed,
per Franke’s installation instructions, in their original installation, and used in normal indoor residential kitchen
applications. Any products or components which have been modified or altered from their original intended condition will
void the Warranty. The Franke Warranties for Faber branded products are limited to the original purchaser and are non-
transferrable. These Warranties do not include products purchased from non-Authorized Retailers, products that are
obsolete or discontinued, or products that were previous display models. All issues with installed products are considered
warranty claims and not subject to the Return Policy. Franke reserves the right to inspect any Franke / Faber product
reported to be defective pursuant to a Warranty claim and the original installation prior to providing a replacement product
and/or component. All decisions are final. In no situation shall the liability of Franke exceed the amount of the original
purchase price.
The Warranties do not cover, and Franke shall not be liable for, any damage to products or components resulting from
misuse or abuse, accidental damages, normal wear such as scuffs, scratches or finish reduction/fading, improper
installation, abnormal usage, negligence, damage caused by improper maintenance or cleaning. Damage caused by
impurities, corrosive chemicals or acts beyond Franke’s control are not covered by any Warranty. Service calls to correct
the installation of a range hood, instructions on how to operate a range hood, to replace or repair house fuses or to correct
house wiring or plumbing are not covered by any Warranty. Service calls to repair or replace range hood light bulbs, fuses
or filters and these consumable part costs are also excluded from Warranty coverage. Installation not in accordance with
electrical or plumbing codes or Franke / Faber documentation are not covered by any Warranty. Replacement parts or
repair labor costs for units operated outside the United States, Canada or Latin America, including any non-UL or C-UL or
non-NOM approved Franke / Faber range hoods are excluded from Warranty coverage. Expenses for travel and
transportation for service in remote locations and pickup and delivery charges are not covered by any Warranty. Franke /
Faber range hoods should always be serviced in the home in their original installation.
Franke / Faber product replacements do not include liability for project delays. Product replacements are not guaranteed
to be exact replacements. If the original product is not available at the time of the warranty claim, at Franke’s option, the
product replacements will be of similar size, material, and value. Any products or components which have been modified
or altered, from its original intended condition will void the warranty.
The Warranties do not allow recovery of incidental or consequential damages such as loss of use, delay, property
damage or other consequential damage, and Franke accepts no liability for such damages. Each Warranty is limited to
the conditions set forth herein and to the applicable warranty period specified herein and is exclusive. EXCEPT FOR THE
WARRANTIES SET FORTH HEREIN, FRANKE MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE
PRODUCTS, INCLUDING, BUT NOT LIMITED TO, (1) ANY WARRANTY OF MERCHANTABILITY, (2) WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE, (3) WARRANTY OF TITLE, OR (4) WARRANTY AGAINST INFRINGEMENT
OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY, WHETHER EXPRESS OR IMPLIED BY LAW, COURSE
OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. LEGAL DISCLAIMER PLEASE
READ CAREFULLY. Franke Kitchen Systems LLC provides the above information to you as a public service to our
customers. By accessing and using this information, you agree to the following and to comply with all applicable laws. If
you do not agree with these terms and conditions, do not use this information. While we try to keep the information
current, changes may have occurred since its creation. Contact your Regional Manager or Customer Service to verify
information regarding Franke Kitchen Systems LLC programs and their use by you.
Franke / Faber Range Hood Limited Warranty:
Franke / Faber range hoods are warranted against any defect in materials or workmanship for the original purchaser for a
period of two (2) years from the date of original purchase when used in standard residential indoor applications. This
warranty covers labor and replacement parts. Franke, at its option, may repair or replace the product or components
necessary to restore the product to good working condition.
Franke Home Solutions Warranty for Franke and Faber Branded Product Effective March 1, 2022
In the United States, Canada and Latin America, Franke warrants the Faber branded products from manufacturing defects
in material and workmanship when purchased from a Franke or Faber Authorized Retailer pursuant to product-specific
warranties detailed herein (each, a “Warranty” and collectively, the “Warranties”). The products must be properly installed, per
Franke’s installation instructions, in their original installation, and used in normal indoor residential kitchen applications. Any
products or components which have been modified or altered from their original intended condition will void the Warranty.
The Franke Warranties for Faber branded products are limited to the original purchaser and are non- transferrable. These
Warranties do not include products purchased from non-Authorized Retailers, products that are obsolete or discontinued, or
products that were previous display models. All issues with installed products are considered warranty claims and not subject
to the Return Policy. Franke reserves the right to inspect any Franke / Faber product reported to be defective pursuant to a
Warranty claim and the original installation prior to providing a replacement product and/or component. All decisions are final.
In no situation shall the liability of Franke exceed the amount of the original purchase price.
The Warranties do not cover, and Franke shall not be liable for, any damage to products or components resulting from misuse
or abuse, accidental damages, normal wear such as scuffs, scratches or finish reduction/fading, improper installation, abnormal
usage, negligence, damage caused by improper maintenance or cleaning. Damage caused by impurities, corrosive chemicals
or acts beyond Franke’s control are not covered by any Warranty. Service calls to correct the installation of a range hood,
instructions on how to operate a range hood, to replace or repair house fuses or to correct house wiring or plumbing are not
covered by any Warranty. Service calls to repair or replace range hood light bulbs, fuses or filters and these consumable part
costs are also excluded from Warranty coverage. Installation not in accordance with electrical or plumbing codes or Franke
/ Faber documentation are not covered by any Warranty. Replacement parts or repair labor costs for units operated outside
the United States, Canada or Latin America, including any non-UL or C-UL or non-NOM approved Franke / Faber range hoods
are excluded from Warranty coverage. Expenses for travel and transportation for service in remote locations and pickup and
delivery charges are not covered by any Warranty. Franke / Faber range hoods should always be serviced in the home in their
original installation.
Franke / Faber product replacements do not include liability for project delays. Product replacements are not guaranteed to
be exact replacements. If the original product is not available at the time of the warranty claim, at Franke’s option, the product
replacements will be of similar size, material, and value. Any products or components which have been modified or altered,
from its original intended condition will void the warranty.
The Warranties do not allow recovery of incidental or consequential damages such as loss of use, delay, property damage or
other consequential damage, and Franke accepts no liability for such damages. Each Warranty is limited to the conditions set
forth herein and to the applicable warranty period specified herein and is exclusive. EXCEPT FOR THE WARRANTIES SET
FORTH HEREIN, FRANKE MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE PRODUCTS, INCLUDING, BUT
NOT LIMITED TO, (1) ANY WARRANTY OF MERCHANTABILITY, (2) WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE,
(3) WARRANTY OF TITLE, OR (4) WARRANTY AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS OF A
THIRD PARTY, WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF
TRADE OR OTHERWISE. LEGAL DISCLAIMER PLEASE
READ CAREFULLY. Franke Kitchen Systems LLC provides the above information to you as a public service to our customers.
By accessing and using this information, you agree to the following and to comply with all applicable laws. If you do not agree
with these terms and conditions, do not use this information. While we try to keep the information current, changes may have
occurred since its creation. Contact your Regional Manager or Customer Service to verify information regarding Franke Kitchen
Systems LLC programs and their use by you.
Franke / Faber Range Hood Limited Warranty:
Franke / Faber range hoods are warranted against any defect in materials or workmanship for the original purchaser for a
period of two (2) years from the date of original purchase when used in standard residential indoor applications. This warranty
covers labor and replacement parts. Franke, at its option, may repair or replace the product or components necessary to
restore the product to good working condition.
15
Franke Home Solutions Warranty for Franke and Faber Branded Product
Effective March 1, 2022
In the United States, Canada and Latin America, Franke warrants the Faber branded products from manufacturing defects
in material and workmanship when purchased from a Franke or Faber Authorized Retailer pursuant to product-specific
warranties detailed herein (each, a “Warranty” and collectively, the “Warranties”). The products must be properly installed,
per Franke’s installation instructions, in their original installation, and used in normal indoor residential kitchen
applications. Any products or components which have been modified or altered from their original intended condition will
void the Warranty. The Franke Warranties for Faber branded products are limited to the original purchaser and are non-
transferrable. These Warranties do not include products purchased from non-Authorized Retailers, products that are
obsolete or discontinued, or products that were previous display models. All issues with installed products are considered
warranty claims and not subject to the Return Policy. Franke reserves the right to inspect any Franke / Faber product
reported to be defective pursuant to a Warranty claim and the original installation prior to providing a replacement product
and/or component. All decisions are final. In no situation shall the liability of Franke exceed the amount of the original
purchase price.
The Warranties do not cover, and Franke shall not be liable for, any damage to products or components resulting from
misuse or abuse, accidental damages, normal wear such as scuffs, scratches or finish reduction/fading, improper
installation, abnormal usage, negligence, damage caused by improper maintenance or cleaning. Damage caused by
impurities, corrosive chemicals or acts beyond Franke’s control are not covered by any Warranty. Service calls to correct
the installation of a range hood, instructions on how to operate a range hood, to replace or repair house fuses or to correct
house wiring or plumbing are not covered by any Warranty. Service calls to repair or replace range hood light bulbs, fuses
or filters and these consumable part costs are also excluded from Warranty coverage. Installation not in accordance with
electrical or plumbing codes or Franke / Faber documentation are not covered by any Warranty. Replacement parts or
repair labor costs for units operated outside the United States, Canada or Latin America, including any non-UL or C-UL or
non-NOM approved Franke / Faber range hoods are excluded from Warranty coverage. Expenses for travel and
transportation for service in remote locations and pickup and delivery charges are not covered by any Warranty. Franke /
Faber range hoods should always be serviced in the home in their original installation.
Franke / Faber product replacements do not include liability for project delays. Product replacements are not guaranteed
to be exact replacements. If the original product is not available at the time of the warranty claim, at Franke’s option, the
product replacements will be of similar size, material, and value. Any products or components which have been modified
or altered, from its original intended condition will void the warranty.
The Warranties do not allow recovery of incidental or consequential damages such as loss of use, delay, property
damage or other consequential damage, and Franke accepts no liability for such damages. Each Warranty is limited to
the conditions set forth herein and to the applicable warranty period specified herein and is exclusive. EXCEPT FOR THE
WARRANTIES SET FORTH HEREIN, FRANKE MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE
PRODUCTS, INCLUDING, BUT NOT LIMITED TO, (1) ANY WARRANTY OF MERCHANTABILITY, (2) WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE, (3) WARRANTY OF TITLE, OR (4) WARRANTY AGAINST INFRINGEMENT
OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY, WHETHER EXPRESS OR IMPLIED BY LAW, COURSE
OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. LEGAL DISCLAIMER PLEASE
READ CAREFULLY. Franke Kitchen Systems LLC provides the above information to you as a public service to our
customers. By accessing and using this information, you agree to the following and to comply with all applicable laws. If
you do not agree with these terms and conditions, do not use this information. While we try to keep the information
current, changes may have occurred since its creation. Contact your Regional Manager or Customer Service to verify
information regarding Franke Kitchen Systems LLC programs and their use by you.
Franke / Faber Range Hood Limited Warranty:
Franke / Faber range hoods are warranted against any defect in materials or workmanship for the original purchaser for a
period of two (2) years from the date of original purchase when used in standard residential indoor applications. This
warranty covers labor and replacement parts. Franke, at its option, may repair or replace the product or components
necessary to restore the product to good working condition.
This warranty supersedes all other warranties, expressed or implied. No employee, field sales
representatives, or distribution persons are authorized to give any warranties on behalf of Franke Kitchen
Systems, LLC
To make an installed product warranty claim please contact Franke at the provided contact information
below. All warranty claims must include the following for processing:
1. Proof of purchase from Franke or Faber Authorized Retailer
2. Original purchaser’s name, address (included city, state, zip), email address and phone number
3. Franke / Faber model and serial number
4. Date of installation
5. Description of the defect
6. Photos of the defect
In North America and Latin America:
Franke Home Solutions
Attn: Warranty Department
800 Aviation Parkway
Smyrna, TN 37167
HS-Warranty.US@Franke.com
Legal Entity:
Franke Kitchen Systems LLC
16
VEUILLEZ LIRE ET CONSERVER LA PRÉSENTE NOTICE AVANT DE
COMMENCER L'INSTALLATION DE LA HOTTE DE CUISINE
AVERTISSEMENT:POURRÉDUIRELERISQUED'UNFEUDEGRAISSESURLATABLEDECUISSON:
a) Ne laissez jamais sans surveillance les éléments de la surface de cuisson à température élevée. Les
bouillonnements excessifs peuvent provoquer de la fumée et les débordements de graisse peuvent
s'enflammer. L'huile doit être chauffée lentement, à une température basse ou moyenne.
b) Assurez-vous de toujours mettre en marche le ventilateur de la hotte lorsque vous cuisinez à tem-
pératureélevéeoupréparezunmetsflambé(p.ex.crêpesSuzette,cerisesjubilé,bœufflambé).
c) Nettoyez régulièrement les ventilateurs d'aspiration. Assurez-vous de ne pas laisser de la graisse
s'accumuler sur le ventilateur ou le filtre.
d) Utilisez toujours des poêles et casseroles de la taille appropriée. Utilisez toujours des ustensiles de
cuisine de la taille adaptée à celle de l'élément chauffant.
AVERTISSEMENT:-POURPRÉVENIRLESBLESSURESENCASDEFEUDEGRAISSESURLATABLE
DECUISSON,SUIVEZLESRECOMMANDATIONSSUIVANTES*:
a) ÉTOUFFEZ LES FLAMMES à l'aide d'un couvercle hermétique, d'une plaque à biscuits ou d'un plateau
métallique, puis éteignez le brûleur. FAITES ATTENTION AUX BRÛLURES. Si le feu ne s'éteint pas
immédiatement, QUITTEZ LES LIEUX ET APPELEZ LES POMPIERS.
b) NE PRENEZ JAMAIS UNE CASSEROLE EN FLAMME - Vous pourriez vous brûler.
c) N'UTILISEZ JAMAIS DE L'EAU, ni un linge à vaisselle ou un torchon mouillé, pour éteindre le feu.
Cela pourrait provoquer une violente explosion de vapeur.
d)UtilisezunextincteurUNIQUEMENTsi:
1. Vous êtes certain qu'il s'agit d'un extincteur de classe ABC et que vous connaissez bien son
mode d'emploi.
2. Le feu est de faible intensité et se limite à l'endroit où il a démarré.
3. Les pompiers ont déjà été appelés.
4. Une voie de sortie se trouve derrière vous pendant que vous éteignez les flammes.
* D'après le guide «Kitchen Firesafety Tips» publié par la NFPA aux États-Unis
AVERTISSEMENT - POUR RÉDUIRE LE RISQUE D'INCENDIE OU DE CHOC ÉLECTRIQUE, n'utilisez
jamais ce ventilateur en association avec un dispositif de réglage de vitesse à semi-conducteurs.
AVERTISSEMENT - POUR RÉDUIRE LES RISQUES D'INCENDIE, DE CHOC ÉLECTRIQUE OU DE
BLESSURECORPORELLE,RESPECTEZLESINSTRUCTIONSSUIVANTES:
1. Utilisez cet appareil uniquement de la façon prévue par le fabricant. Pour toute question, com-
muniquez avec le fabricant.
2. Avant de procéder à l'entretien ou au nettoyage de l'appareil, coupez l'alimentation au niveau du
panneau électrique et verrouillez-le pour vous assurer que l'électricité n'est pas rétablie accidentel-
lement. S'il n'est pas possible de verrouiller le dispositif d'interruption de l'alimentation, affichez de
façon ferme et bien visible un avis de danger, par exemple à l'aide d'une étiquette sur le panneau.
ATTENTION:Destinéàunusagedeventilationgénéraleuniquement.N'utilisezpascedispositifpour
l'aspiration de vapeurs ou de matériaux dangereux ou explosifs.
AVERTISSEMENT - POUR RÉDUIRE LES RISQUES D'INCENDIE, DE CHOC ÉLECTRIQUE OU DE
BLESSURECORPORELLE,RESPECTEZLESINSTRUCTIONSSUIVANTES:
1. L'installation et le branchement électrique doivent être réalisés par un technicien qualifié et con-
formément à tous les codes et normes en vigueur, incluant ceux concernant la construction à
l'épreuve du feu.
2. Afin de garantir une combustion et une évacuation adéquates des gaz par les conduites de la che-
minée des appareils à combustion, une bonne aération est nécessaire pour éviter le refoulement.
Respectez les lignes directrices fournies par le fabricant du matériel chauffant, ainsi que les normes
desécuritécommecellespubliéesparlaNationalFireProtectionAssociation(NFPA)etlaAmerican
SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE)auxÉtats-Unis,ainsi
que les codes en vigueur dans votre région.
3. Lorsque vous faites une ouverture ou percez dans un mur ou le plafond, veillez à ne pas endom-
mager les fils électriques ou d'autres dispositifs cachés.
17
4. Les ventilateurs canalisés doivent toujours être raccordés à l'extérieur.
TOUTE OUVERTURE DANS LE MUR OU LE PLANCHER À PROXIMITÉ DE LA HOTTE DOIT
ÊTRE SCELLÉE.
Un espace libre d'au moins 24" est requis entre le bas de la hotte et la surface de cuisson ou le comptoir.
Cette hotte a été homologuée par l'UL à cette distance de la surface de cuisson.
L’espace libre minimal requis peut-être plus grand, selon la réglementation en matière de construction de votre
région. Pour les cuisinières à gaz et les cuisinières combinées, un espace minimal de 30" est recommandé
et pourrait être exigé.
Les armoires suspendues de chaque côté de l'appareil doivent se trouver à au moins 18" de la surface de
cuisson ou du comptoir. Consultez la notice d'installation de la surface de cuisson ou de la cuisinière fournie
par le fabricant avant de pratiquer des ouvertures.
INSTALLATION DANS UNE MAISON MOBILE L'installation de cette hotte doit être conforme à la Partie
3280 de la norme Manufactured Home Construction and Safety Standards, Title 24 CFR (précédemment
la partie 280 de la norme Federal Standard for Mobile Home Construction and Safety, Title 24, HUD).
Consultez la che technique électrique.
• Le système de ventilation DOIT déboucher à l'extérieur.
• NE FAITES PAS déboucher les conduits dans un grenier ou un autre endroit fermé.
• N'UTILISEZ PAS un clapet de sécheuse mural de 4po.
• Il n'est pas recommandé d'utiliser des conduits exibles.
• N'ENTRAVEZ PAS le ux de l'air de combustion et de ventilation.
• Le non-respect des exigences en matière de ventilation pourrait entraîner un incendie.
AVERTISSEMENT
!
CRITÈRES DE VENTILATION
Déterminez quelle méthode de ventilation est mieux adaptée à votre application. Les conduits peuvent passer
par le mur ou le toit.
Pour garantir une meilleure efficacité, la longueur des conduits et le nombre de coudes doivent être le plus
limités que possible. Le diamètre des conduits devrait être uniforme. N'installez pas deux coudes ensemble.
Utilisez un ruban pour canalisations afin de sceller tous les joints du système de conduits. Utilisez un calfeutrage
pour sceller les ouvertures dans le mur extérieur ou le plancher, autour du clapet.
Il n'est pas recommandé d'utiliser des conduits flexibles. Les conduits flexibles provoquent une contre-pression
et de la turbulence qui diminuent grandement l'efficacité de l'appareil.
Assurez-vous que l'espace libre dans le mur ou le plancher est suffisant pour le conduit d'évacuation avant de
pratiquer les ouvertures. Ne coupez jamais une poutre ou un chevron, sauf si c'est absolument nécessaire.
S'il s'avère nécessaire de couper une poutre ou un chevron, la construction d'un renforcement est requise.
AVERTISSEMENT - Pour réduire le risque d'incendie, utilisez uniquement des conduits métalliques.
ATTENTION - Pour réduire le risque d'incendie et pour évacuer adéquatement l'air, assurez-vous
deraccorderlesconduitsàl'extérieur–Nediffusezpasl'aird'évacuationdansdesespacesà
l'intérieur des murs ou du plafond, ou encore à l'intérieur d'un grenier, d'une galerie technique ou
d'un garage.
Installation dans les climats froids
Le système de ventilation doit prévoir un registre antirefoulement supplémentaire pour réduire le ux d'air
froid inverse, ainsi qu'une barrière thermique non métallique pour réduire la conduction des températures
extérieures. Le registre doit être installé du côté air froid par rapport à la barrière thermique. La barrière
thermique doit être positionnée le plus près que possible de l'endroit où le système de ventilation pénètre
dans la partie chauffée de la maison.
18
• Une mise à la terre électrique est requise pour cette hotte.
• N'UTILISEZ PAS un tuyau d'eau froide pour la mise à la terre si celui-ci est branché par des
joints en plastique, par des rondelles non métalliques ou d'autres matériaux.
• N'UTILISEZ PAS une conduite de gaz pour la mise à la terre.
• N'INSTALLEZ PAS un fusible sur le circuit neutre ou le circuit de mise à la terre. La présence
d'un fusible dans le circuit neutre ou de mise à la terre peut entraîner un choc électrique.
• Consultez un électricien qualié si vous n'êtes pas certain de la mise à la terre de la hotte.
• Le non-respect des exigences de la che technique électrique pourrait entraîner un incendie.
AVERTISSEMENT
!
FICHE TECHNIQUE ÉLECTRIQUE
Une alimentation de courant alternatif de 120 volts à 60Hz est requise sur un circuit à
fusible distinct de 15 ampères. Il est recommandé d'installer un fusible temporisé ou
un disjoncteur. Le fusible doit être calibré conformément aux codes en vigueur pour les
caractéristiques nominales électriques de l'appareil, indiquées sur la plaque signalétique
située à l'intérieur de l'appareil, à proximité du compartiment des câblages externes.
19
OUVERTURE
DIMENSIONS DE CRISTAL HC
GARNITURE AVANT EN OPTION
La nouvelle hotte Cristal HC est équipée d’une bande d’acier inoxydable installée. Des bandes en option, de couleur noire ou blanche,
peuvent être achetées. Pour une bande avant personnalisée, il est aussi possible de s’adresser à une boutique spécialisée dans la vente
d’armoires pour obtenir une bande coordonnée à vos armoires
DIMENSIONS DE LA GARNITURE SUR MESURE
1 15/32"
3/4"
29 7/8" or 35 7/8"
25 1/2” - 31 1/2”
10”
25 1/2” - 31 1/2”
13/16”
17 1/2” - 23 1/2”
5 7/8”
Planification de l’installation - Important : Il est recommandé d'installer cette hotte à une distance d'au moins 24" de la
surface de cuisson et à une distance maximale de 30” pour une efficacité optimale. Reportez-vous également aux
recommandations du fabricant de la surface de cuisson. REMARQUE : En cas de ventilation directement à l’arrière,
utilisez le diagramme des dimensions latérales de droite. En cas de ventilation vers le haut (position standard),
utiliser le diagramme des dimensions de gauche. Reportez-vous à la page 5 pour de plus amples renseignements sur
la ventilation directement à l’arrière.
3 15/16”
DIMENSIONS LATÉRALES - CRISTAL HC
(VENTILATION VERS LE HAUT - STANDARD)
DIMENSIONS LATÉRALES - CRISTAL HC
(OPTION DE VENTILATION DIRECTEMENT À L’ARRIÈRE)
3 15/16”
20
INFORMATIONS ARRIÈRE HOTTE 36"
INFORMATIONS ARRIÈRE HOTTE 30"
DRAFT 25-MAY-2020 18:52
Palazzi, Walter
15-Nov-2019
Released
= =
DRAFT 25-MAY-2020 18:52
DRAFT 25-MAY-2020 18:52
21
Version 06/14 - Page 5
9.0 pieds
10.0 pieds
0.0 pieds
19.0 pieds
OUTILS REQUIS POUR L’INSTALLATION
•Scie sauteuse ou scie à découper
•Perceuse
•Mèche pour bois de 1 1/4"
•Pinces
•Tournevis cruciforme
•Dénudeur de fil ou couteau tout usage
•Cisailles à métaux
•Ruban à mesurer ou règle
•Niveau
•Crayon
•Pistolet de calfeutrage
•Ruban pour canalisation
PIÈCES FOURNIES POUR L’INSTALLATION
PIÈCES REQUISES POUR L’INSTALLATION
• 2 connecteurs de conduit
• Câble d’alimentation électrique
• 1 clapet mural ou clapet de toiture
• Canalisation entièrement métallique
PLANIFIER LA CANALISATION
INSTALLATIONS AVEC RECYCLAGE
FIGURE 3A
45˚ Coude
90˚ Coude
90˚ Coude plat
Clapet mural
FIGURE A
Conduit droit de 9 pieds
2 - 90˚ coudes
Clapet mural
Système total
FIGURE B
3.0 pieds
5.0 pieds
12.0 pieds
0.0 pieds
CANALISATION
VERTICALE
FIGURE 2
CANALISATION
HORIZONTALE
FIGURE 1
armoire
plafond
conduit circulaire de 6”
hotte
armoire
plafond
conduit circulaire de 6”
hotte
grille d’évent
grille d’évent
FIGURE 3B
FIGURE 3
La hotte coulissante Cristal HC est conçue pour offrir une grande flexibilité en matière d’installation.
Il est possible d’installer une canalisation verticale ou horizontale, par un conduit circulaire de 6".
Il est aussi possible d’installer l’appareil en le configurant de façon à ce que l’air soit recyclé.
L’appareil est configuré en vue d’une installation avec canalisation verticale par défaut.
Les FIGURES 1 et 2 illustrent l’installation verticale et horizontale de l’appareil. La FIGURE 3 illustre
l’installation avec recyclage. La hotte Cristal HC nécessite des conduits circulaires de 6".
La canalisation doit être la plus courte et droite que possible, pour que le ventilateur fonctionne au
maximum de ses capacités.
•1 registre antirefoulement
•1 grille d’évent (pour installation avec recyclage
uniquement)
•1 garniture de vinyle
•1 documentation
Pour des résultats satisfaisants, la canalisation ne devrait
pas être supérieure à l’équivalent de 50 pieds si la
canalisation est réalisée avec le conduit circulaire minimum
de 6". L’équivalent en pieds de chaque élément de
canalisation du système de la FIGURE A.
Un exemple est donné sur la FIGURE B.
Pour des résultats optimaux, n’utilisez pas plus de trois
coudes de 90°. Si plus d’un coude est utilisé, assurez-vous
qu’un conduit linéaire d’une longueur minimale de 24" se
trouve entre deux coudes. N’installez pas deux coudes
ensemble. Si vous devez installer tout de suite un coude,
placez-le le plus loin possible de l’ouverture d’évacuation de
la hotte.
Pour la ventilation directement à l’arrière (FIGURE 2), vous
devez changer la position du ventilateur. Retirez les 12 vis
qui relient le carter de métal au bâti de la hotte.
Retirez les 4 vis qui relient le carter du ventilateur au carter
de métal. Faites tourner le ventilateur de 90 degrés vers
l’arrière, puis faites-le tourner de 180 degrés.
Assurez-vous que le câble d’alimentation électrique est dans
une position adéquate. Remettez toutes les vis en place,
en vous assurant qu’elles sont bien serrées.
Pour les installations avec recyclage (FIGURE 3), il est nécessaire d'installer des filtres à charbon. Retirez les quatre filtres à graisse et mettez-les à part. Posez
un filtre à charbon à chaque extrémité du ventilateur. Chaque filtre à charbon se fixe à la grille noire sur le côté du ventilateur. Faites tourner le filtre dans le sens
des aiguilles d'une montre pour l'installer et dans le sens contraire des aiguilles d'une montre pour l'enlever (FIGURE 3A). Remettez les quatre filtres à graisse
en place. Une canalisation doit être installée pour évacuer la hotte dans la cuisine, soit au sommet des armoires ou sur la face du parement. Une grille d’évent
de plastique (FIGURE 3B) fournie avec la hotte peut être utilisée pour couvrir l’ouverture du conduit. Cette canalisation ne doit pas se terminer dans un espace
sans circulation d'air.
22
Version 06/14 - Page 6
OPTIONAL ACCESSORIES FOR PURCHASE SEPARATELY
ACCESSOIRES EN OPTION POUR ACHETER SÉPARÉMENT
• Charcoal Filters
For non-vented installations only, replace charcoal
lters as needed part # FILTER1
• CFM Reducer Kit
To reduce cfm to below 300 cfm for use in
make up air environments part # CFMRED
• Universal Make Up Air Damper 6"
Brings fresh air back into the home thru an automatic
damper when the hood is on #MUDAMPER6
• Universal Make Up Air Damper 8"
Brings fresh air back into the home thru an automatic
damper when the hood is on #MUDAMPER8
• Front Trim Kits
Replace stainless trim on the slide out hood with a
black or white trim (available in 30" or 36")
CRTRIM30WH (30" white)
CRTRIM30BK (30" black)
CRTRIM36WH (36" white)
CRTRIM36BK (36" black)
• Filtres à charbon
Pour les installations non ventilé seulement, rem-
placer le charbon de bois
ltres au besoin partie # FILTER1
• Réducteur de CFM Kit
Pour réduire cfm à 300 cfm ci-dessous pour une
utilisation dans
compenser milieux aériens partie # CFMRED
• Universal Make Up registre d'air 6"
Apporte de l'air frais de nouveau dans la maison à
travers un amortisseur automatique lorsque le capot
est sur # MUDAMPER6
• Universal Make Up Air Amortisseur 8"
Apporte de l'air frais de nouveau dans la maison à
travers un amortisseur automatique lorsque le capot
est sur # MUDAMPER8
• Front Bordure Kits
Remplacer la garniture inoxydable sur la diapositive
sur le capot avec un
équilibre noir ou blanc (disponible en 30 "ou 36")
CRTRIM30WH (30 "blanc)
CRTRIM30BK (30 "noir)
CRTRIM36WH (36 "blanc)
CRTRIM36BK (36 "noir)
"When used in recirculation mode, to Reduce the Risk of
Fire and Shock use only conversion kit Model FILTER 1 -
FILTER1LL"
Version 06/14 - Page 6
OPTIONAL ACCESSORIES FOR PURCHASE SEPARATELY
ACCESSOIRES EN OPTION POUR ACHETER SÉPARÉMENT
• Charcoal Filters
For non-vented installations only, replace charcoal
lters as needed part # FILTER1
• CFM Reducer Kit
To reduce cfm to below 300 cfm for use in
make up air environments part # CFMRED
• Universal Make Up Air Damper 6"
Brings fresh air back into the home thru an automatic
damper when the hood is on #MUDAMPER6
• Universal Make Up Air Damper 8"
Brings fresh air back into the home thru an automatic
damper when the hood is on #MUDAMPER8
• Front Trim Kits
Replace stainless trim on the slide out hood with a
black or white trim (available in 30" or 36")
CRTRIM30WH (30" white)
CRTRIM30BK (30" black)
CRTRIM36WH (36" white)
CRTRIM36BK (36" black)
• Filtres à charbon
Pour les installations non ventilé seulement, rem-
placer le charbon de bois
ltres au besoin partie # FILTER1
• Réducteur de CFM Kit
Pour réduire cfm à 300 cfm ci-dessous pour une
utilisation dans
compenser milieux aériens partie # CFMRED
• Universal Make Up registre d'air 6"
Apporte de l'air frais de nouveau dans la maison à
travers un amortisseur automatique lorsque le capot
est sur # MUDAMPER6
• Universal Make Up Air Amortisseur 8"
Apporte de l'air frais de nouveau dans la maison à
travers un amortisseur automatique lorsque le capot
est sur # MUDAMPER8
• Front Bordure Kits
Remplacer la garniture inoxydable sur la diapositive
sur le capot avec un
équilibre noir ou blanc (disponible en 30 "ou 36")
CRTRIM30WH (30 "blanc)
CRTRIM30BK (30 "noir)
CRTRIM36WH (36 "blanc)
CRTRIM36BK (36 "noir)
- # FILTER1LL
- # FILTER1LL
23
INSTALLER LA HOTTE
1. Retirez la hotte de la boîte et placez-la sur une surface plane. Recouvrez
la surface pour éviter les dommages accidentels. Retirez toutes les pièces,
incluant le registre antirefoulement, la grille de plastique et l’ensemble de la
documentation avant de jeter la boîte. Retirez les filtres à graisse et mettez-
les à part.
FIGURE 5
2. La hotte est fixée à l’armoire à l’aide de deux brides à ressort, une de
chaque côté de la hotte (FIGURE 6). Soulevez la hotte pour l’insérer dans
l’ouverture pratiquée dans l’armoire. Prenez soin de ne pas endommager
l’armoire,
la hotte ou les autres appareils.
OUVERTURE
PRÉPARER L’ARMOIRE
1. Débranchez et déplacez la cuisinière de l’ouverture de l’armoire
pour faciliter l’accès à l’armoire du haut et au mur arrière. Placez une
protection épaisse sur la surface de cuisson, la cuisinière encastrée
ou le comptoir pour éviter qu'ils soient endommagés ou salis.
2. Déterminez la ligne centrale de l’endroit où la hotte sera installée
et marquez-la clairement sur le mur et le dessous de l’armoire où la
hotte sera installée.
FIGURE 4
RÉALISER L’OUVERTURE (FIGURE 5) OÙ LA HOTTE
SERA INSTALLÉE.
4. Déterminez les ouvertures adéquates à réaliser pour la canalisation.
Pratiquez toutes les ouvertures nécessaires dans le mur ou dans
l’armoire pour réaliser la canalisation. Installez la canalisation avant de
monter la hotte.
5. Déterminez les ouvertures adéquates pour le câble d’alimentation et
réalisez-les. Utilisez une mèche de 1 1/4" pour percer ce trou. Faites passer
le câble d’alimentation dans le mur ou l’armoire. NE METTEZ PAS
l'alimentation sous tension avant d'avoir terminé l'installation.
Utiliser un calfeutrage pour sceller autour de l’ouverture des câbles.
FIGURE 6
4. Les brides à ressort sont réglées pour s’adapter à une épaisseur entre
1 3/16" et 2 1/4". Si l’épaisseur du fond de l’armoire est inférieur à 1 3/16",
les brides à ressort peuvent être enlevées et replacée à une position
inférieure depuis le réglage supérieur vers le réglage inférieur, en retirant
les quatre vis cruciformes.
5. Fixez la hotte à l’armoire en serrant les vis à l’aide d’un tournevis
cruciforme.
6. Une bande de vinyle grise (FIGURE 7) est comprise pour recouvrir le
bas de l’armoire qui reste exposé. Fixez la bande de vinyle grise au bas
de l’arrière de la hotte à l’aide des trois vis fournies. Au besoin, cette
bande peut être coupée pour être adaptée à la profondeur de l’armoire.
BANDE DE VINYLE
25 1/2” - 31 1/2”
10”
25 1/2” - 31 1/2”
13/16”
17 1/2” - 23 1/2”
5 7/8”
3. Si le fond de l’armoire est en retrait, des blocs de bois doivent être
installés pour assurer un alignement adéquat avec le fond de
l’armoire. Les blocs de bois doivent être alignés ou en retrait de
1/16" à 1/8" par rapport au fond de l’armoire, comme indiqué sur la FIGURE 4..
BANDES DE BOIS D’APPOINT
Installation avec ventilation canalisée
Installez les 2 volets de de clapet inclus avec la hotte
de cuisinière comme illustré.
24
7
Boîtier de connexion directe,
no d'article WIREBOX
(acheté séparément)
Created by
-
Denomination
-
Lang EN Sheet
1
/1
Modif.by
Approved by
Approval date
Doc. status
Drawing N.
NEW_DRAWING_BOX
Rev
01
INSTALLATION ÉLECTRIQUE AVEC BOÎTIER
DE CONNEXION EN OPTION
Pour une installation avec connexion xe, utilisez
uniquement la trousse de boîtier de connexion pour
hotte indiquée,
no d'article WIREBOX, fabriquée par Faber.
Max. 33 7/16”
INSTRUCTIONS DE MISE À LA TERRE Cet appareil doit être mis à la
terre. La mise à la terre réduit le risque de choc électrique en cas de
court-circuit, car elle fournit un l d'évacuation au courant électrique.
Cet appareil est muni d'un cordon présentant un l de mise à la terre,
avec une che de mise à la terre. La che doit être insérée dans une
prise correctement installée et mise à la terre.
AVERTISSEMENT - Une mise à la terre inadéquate peut entraîner
un choc électrique.
Consultez un électricien qualié si vous ne comprenez pas parfaitement
les instructions de mise à la terre ou si vous avez des doutes quant
à la mise à la terre de l'appareil.
N'utilisez pas de rallonge. Si le cordon d’alimentation est trop court,
demandez à un électricien qualié d’installer une prise à proximité
de l'appareil.
INSTALLATION ÉLECTRIQUE
AVEC CÂBLE DE CONNEXION
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/O Switch
TheOn/O switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light o.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower o.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut o when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is o, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The New Cristal comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
FIGURE 8
1 15/32"
FIGURE 9
3/4"
29 7/8" or 35 7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/O Switch
TheOn/O switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light o.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower o.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut o when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is o, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The New Cristal comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
FIGURE 8
1
15/32"
FIGURE 9
3/4"
29
7/8"
or 35
7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
GARNITURE AVANT EN OPTION
La nouvelle hotte Cristal est équipée d’une bande d’acier inoxydable
installée. Pour modier la bande avant, enlevez les trois vis cruciformes
situées derrière la bande (FIGURE 8). Au besoin, la bande avant peut-
être réglée en desserrant les trois vis cruciformes et en faisant glisser la
bande) vers le haut ou vers le bas. Serrez les vis lorsque la bande est
placée correctement.
Pour une bande avant personnalisée, il est aussi possible de s’adresser
à une boutique spécialisée dans la vente d’armoires pour obtenir une
bande coordonnée à vos armoires. Les dimensions de la bande avant
sont indiquées sur la FIGURE 9.
Panneau
coulissant
Bande
avant
Trois vis
25
INFORMATIONS POUR L'UTILISATION ET L'ENTRETIEN
Pour de meilleurs résultats
Activez la hotte quelques minutes avant de commencer à cuisiner pour créer un ux d'air
adéquat. Laissez la hotte fonctionner quelques minutes après avoir ni de cuisiner pour
absorber toute la fumée et les odeurs de la cuisine.
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/Off Switch
TheOn/Off switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light off.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower off.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut off when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
proper airow. Allow the unit to operate for several minutes
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
The metal grease lters should be cleaned frequently in hot
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
agents can scratch rangehood nishes and should not be
used to clean nished surfaces.
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is off, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The Cristal HC comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9.
FIGURE 8
1 15/32"
FIGURE 9
3/4"
29 7/8" or 35 7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
Panneau de commande de la hotte
Toutes les commandes sont situées sur le côté droit de la hotte.
Interrupteur d’éclairage
L’interrupteur de l’éclairage halogène se trouve derrière la garniture avant. Placer l’interrupteur à la
position 1 pour allumer l’éclairage. Placer l’interrupteur à la position 0 pour éteindre l’éclairage.
Commutateur de réglage de vitesse du ventilateur
B sur la FIGURE 10 représente le commutateur de réglage de vitesse du ventilateur. Placer le com-
mutateur à la position 1 pour allumer le ventilateur à la vitesse RÉDUITE. Placer le commutateur à
la position 2 pour allumer le ventilateur à la vitesse MOYENNE. Placer le commutateur à la position
3 pour allumer le ventilateur à la vitesse ÉLEVÉE. Placer l’interrupteur à la position 0 pour éteindre
le ventilateur.
Fonctionnement automatique
Si le commutateur du ventilateur et l’interrupteur de l’éclairage sont allumés, le ventilateur et l’éclairage
sont activés automatiquement quand le panneau coulissant est ouvert, et ils sont désactivés quand
le panneau coulissant est fermé.
26
Nettoyagedesltresàgraissemétal-
liques
Les ltres à graisse métalliques peuvent être lavés dans une
solution d'eau chaude savonneuse ou dans le lave-vaisselle.
Ils devraient être nettoyés tous les 2 mois d'utilisation, ou plus
fréquemment en cas d'utilisation particulièrement intensive.
• Ouvrez le panneau coulissant en le tirant.
• Retirez le ltre, en poussant simultanément le levier vers
l'arrière de l'appareil et en le tirant vers le bas.
• Lavez le ltre sans le plier. Laissez-le sécher complètement
avant de le réinstaller (un changement de la couleur à la
surface du ltre au l du temps n'a aucun impact sur son
efcacité).
• Remettez-le en place, en vous assurant que la poignée
se trouve vers l'avant.
• Le lave-vaisselle pourrait ternir le ni du ltre à graisse
métallique.
• Fermez le panneau coulissant.
Remplacementdultreàcharbonactif
Les ltres à charbon actif ne sont pas lavables et ne peuvent
être régénérés. Ils doivent être remplacés environ tous les
4 mois d'utilisation, ou plus souvent en cas d'utilisation
intensive.
• Ouvrez le panneau coulissant en le tirant.
• Retirez le ltre, en le poussant simultanément vers l'arrière
de l'appareil et en le tirant vers le bas.
• Retirez les ltres à charbon actif saturés comme indiqué (A).
• Posez les nouveaux ltres, comme indiqué (B).
• Remettez-les en place, en vous assurant que la poignée
se trouve vers l'avant.
• Fermez le panneau coulissant.
EN 7
7
INSTALLATION
Fitting the Hood canopy
BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:
• Disconnect the wires to the Commands at the connectors.
• Disconnect the wires to the Light at the con-
nectors.
• The Hood can be installed directly on the
underside of the wall unit (Minimum 650 mm
from the Cooker Hob).
• Create an opening in the bottom of the wall unit,
as shown.
• Insert the hood until the side supports snap into
place.
• Fasten using the 10 screws 12a provided.
• Lock in position by tightening the screws Vf from
underneath the hood.
• Open the suction panel by turning the specific knob.
• Disconnect the panel from the hood canopy by sliding the
fixing pin lever.
• Remove grease filters.
• Screw the Frame into place
using the 6 screws 12f, re-
connect the wires to the
Commands and Light, re-
place the metal grease filter
and the Panel.
260
13
495 - 675
Lampes DEL à ballast
intégré de type Gu10 –
répondant à
la norme UL
1993/nmx-j-
578/1-ance/
csa c22.2 No
1993
Système d'éclairage
• Coupez l'alimentation électrique avant de
remplacer les ampoules et assurez-vous
qu'elles sont froides au toucher avant de
commencer.
• Retirez l'ampoule de la base. Faites tourner
légèrement vers la gauche et retirez-la du
socle.
• Remplacez l'ampoule avec une nouvelle
du même type, en vous assurant d'insérer
correctement les deux connecteurs dans
leur logement sur le socle.
• Lorsque les connecteurs de l'ampoule sont
en place, faites tourner légèrement vers la
droite pour verrouiller.
27
Schéma de câblage
0123456789
R
P
P
H90_496 01
Drawing N : Rev :
Modif. by
Doc.status
Do not get quotas from the drawing do not bring
modifications without authorization of techincal office.
According to the law we reserve the own of the present
drawing with reproduction prohibition partial or total.
Approved date
Modification description
Approved by
WIRING DIAGRAM M8_4V SCL HV LED
Doc Type
Denomination
Creation date
02.Mar.2018
DOLCE CORRADO
Created by
991.0520.839
Code
LED
0
1
SW3
LED
RV
CN3
RED (org)
VLT(org)
LB WH A GR
CN2
WHT
WHT
BRW
BLU
0 1 2 3
SW2
RED
123
654
789
PNK
BLU
PNK
BK BR
CN1
RED
BRW
SIDE
INSERT
CABLE
SW1
BLK
123
654
987
PNK
M8-4V
BRW
ORG
M1
WHT
BLU
BLK
GRY
6,3uF
Y-G
WHT
220-240V ~ 50Hz
110-127V ~ 60Hz
220 ~ 60Hz
Y-G
BLK
28
GARANTIE
Franke Home Solutions Warranty for Franke and Faber Branded Product
Effective March 1, 2022
In the United States, Canada and Latin America, Franke warrants the Faber branded products from manufacturing defects
in material and workmanship when purchased from a Franke or Faber Authorized Retailer pursuant to product-specific
warranties detailed herein (each, a “Warranty” and collectively, the “Warranties”). The products must be properly installed,
per Franke’s installation instructions, in their original installation, and used in normal indoor residential kitchen
applications. Any products or components which have been modified or altered from their original intended condition will
void the Warranty. The Franke Warranties for Faber branded products are limited to the original purchaser and are non-
transferrable. These Warranties do not include products purchased from non-Authorized Retailers, products that are
obsolete or discontinued, or products that were previous display models. All issues with installed products are considered
warranty claims and not subject to the Return Policy. Franke reserves the right to inspect any Franke / Faber product
reported to be defective pursuant to a Warranty claim and the original installation prior to providing a replacement product
and/or component. All decisions are final. In no situation shall the liability of Franke exceed the amount of the original
purchase price.
The Warranties do not cover, and Franke shall not be liable for, any damage to products or components resulting from
misuse or abuse, accidental damages, normal wear such as scuffs, scratches or finish reduction/fading, improper
installation, abnormal usage, negligence, damage caused by improper maintenance or cleaning. Damage caused by
impurities, corrosive chemicals or acts beyond Franke’s control are not covered by any Warranty. Service calls to correct
the installation of a range hood, instructions on how to operate a range hood, to replace or repair house fuses or to correct
house wiring or plumbing are not covered by any Warranty. Service calls to repair or replace range hood light bulbs, fuses
or filters and these consumable part costs are also excluded from Warranty coverage. Installation not in accordance with
electrical or plumbing codes or Franke / Faber documentation are not covered by any Warranty. Replacement parts or
repair labor costs for units operated outside the United States, Canada or Latin America, including any non-UL or C-UL or
non-NOM approved Franke / Faber range hoods are excluded from Warranty coverage. Expenses for travel and
transportation for service in remote locations and pickup and delivery charges are not covered by any Warranty. Franke /
Faber range hoods should always be serviced in the home in their original installation.
Franke / Faber product replacements do not include liability for project delays. Product replacements are not guaranteed
to be exact replacements. If the original product is not available at the time of the warranty claim, at Franke’s option, the
product replacements will be of similar size, material, and value. Any products or components which have been modified
or altered, from its original intended condition will void the warranty.
The Warranties do not allow recovery of incidental or consequential damages such as loss of use, delay, property
damage or other consequential damage, and Franke accepts no liability for such damages. Each Warranty is limited to
the conditions set forth herein and to the applicable warranty period specified herein and is exclusive. EXCEPT FOR THE
WARRANTIES SET FORTH HEREIN, FRANKE MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE
PRODUCTS, INCLUDING, BUT NOT LIMITED TO, (1) ANY WARRANTY OF MERCHANTABILITY, (2) WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE, (3) WARRANTY OF TITLE, OR (4) WARRANTY AGAINST INFRINGEMENT
OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY, WHETHER EXPRESS OR IMPLIED BY LAW, COURSE
OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. LEGAL DISCLAIMER PLEASE
READ CAREFULLY. Franke Kitchen Systems LLC provides the above information to you as a public service to our
customers. By accessing and using this information, you agree to the following and to comply with all applicable laws. If
you do not agree with these terms and conditions, do not use this information. While we try to keep the information
current, changes may have occurred since its creation. Contact your Regional Manager or Customer Service to verify
information regarding Franke Kitchen Systems LLC programs and their use by you.
Franke / Faber Range Hood Limited Warranty:
Franke / Faber range hoods are warranted against any defect in materials or workmanship for the original purchaser for a
period of two (2) years from the date of original purchase when used in standard residential indoor applications. This
warranty covers labor and replacement parts. Franke, at its option, may repair or replace the product or components
necessary to restore the product to good working condition.
Garantie Franke Home Solutions pour les produits de marque Franke et Faber en vigueur le 1ermars2022
Aux États-Unis, au Canada et en Amérique latine, Franke garantit les produits de la marque Faber contre les défauts
de fabrication des matériaux et de la fabrication lorsqu’ils sont achetés auprès d’un revendeur agréé Franke ou
Faber conformément aux garanties spécifiques aux produits détaillées dans le présent document (chacune, une
«garantie» et collectivement, les «garanties»). Les produits doivent être correctement installés, conformément
aux instructions d’installation de Franke, dans leur installation d’origine, et utilisés dans des applications de cuisine
résidentielles intérieures normales. Tout produit ou composant qui a été modifié ou altéré par rapport à son état
d’origine annulera la garantie. Les garanties Franke pour les produits de marque Faber sont limitées à l’acheteur
d’origine et ne sont pas transférables. Ces garanties n’incluent pas les produits achetés auprès de revendeurs non
agréés, les produits obsolètes ou abandonnés, ou les produits qui étaient des modèles précédemment affichés. Tous
les problèmes avec les produits installés sont considérés comme des demandes de garantie et ne sont pas soumis
à la politique de retour. Franke se réserve le droit d’inspecter tout produit Franke/Faber signalé comme défectueux
en vertu d’une réclamation au titre de la garantie et de l’installation d’origine avant de fournir un produit et/ou un
composant de remplacement. Toutes les décisions sont finales. La responsabilité de Franke ne pourra en aucun cas
dépasser le montant du prix d’achat initial.
Les garanties ne couvrent pas, et Franke ne sera pas tenue responsable, de tout dommage aux produits ou
composants résultant d’une mauvaise utilisation ou d’un abus, de dommages accidentels, d’une usure normale telle
que des éraflures, des rayures ou d’une réduction/décoloration du fini, d’une installation incorrecte, d’une utilisation
anormale, d’une négligence, des dommages causés par un entretien ou un nettoyage inapproprié. Les dommages
causés par des impuretés, des produits chimiques corrosifs ou des actes indépendants de la volonté de Franke ne
sont couverts par aucune garantie. Les appels de service pour corriger l’installation d’une hotte de cuisinière, les
instructions sur la façon de faire fonctionner une hotte de cuisinière, pour remplacer ou réparer les fusibles de la
maison ou pour corriger le câblage ou la plomberie de la maison ne sont couverts par aucune garantie. Les appels
de service pour réparer ou remplacer les ampoules, les fusibles ou les filtres de la hotte de cuisinière et ces coûts
de pièces consommables sont également exclus de la couverture de la garantie. Une installation non conforme aux
codes électriques ou de plomberie ou à la documentation Franke/Faber n’est couverte par aucune garantie. Les
pièces de rechange ou les coûts de main-d’œuvre de réparation pour les unités utilisées à l’extérieur des États-Unis,
du Canada ou de l’Amérique latine, y compris les hottes de cuisinière Franke/Faber non approuvées UL ou C-UL
ou NOM, sont exclus de la couverture de la garantie. Les frais de déplacement et de transport pour l’entretien dans
des endroits éloignés et les frais de ramassage et de livraison ne sont couverts par aucune garantie. Les hottes de
cuisinière Franke/Faber doivent toujours être entretenues à domicile dans leur installation d’origine.
Les remplacements de produits Franke/Faber n’incluent pas la responsabilité pour les retards de projet. Les
remplacements de produits ne sont pas garantis comme étant des remplacements exacts. Si le produit d’origine
n’est pas disponible au moment de la demande de garantie, à la discrétion de Franke, les produits de remplacement
seront de taille, de matériau et de valeur similaires. Tout produit ou composant qui a été modifié ou altéré par
rapport à son état d’origine annulera la garantie.
Les garanties n’autorisent pas le recouvrement des dommages indirects ou consécutifs tels que la perte d’utilisation,
le retard, les dommages matériels ou autres dommages consécutifs, et Franke décline toute responsabilité pour
ces dommages. Chaque garantie est limitée aux conditions énoncées dans le présent document et à la période
de garantie applicable spécifiée dans le présent document et est exclusive. À L’EXCEPTION DES GARANTIES
ÉNONCÉES DANS LE PRÉSENT DOCUMENT, FRANKE N’OFFRE AUCUNE GARANTIE CONCERNANT LES
PRODUITS, Y COMPRIS, MAIS SANS S’Y LIMITER, (1) TOUTE GARANTIE DE QUALITÉ MARCHANDE, (2)
GARANTIE D’ADÉQUATION À UN USAGE PARTICULIER, (3) GARANTIE DE TITRE DE PROPRIÉTÉ, OU (4)
GARANTIE CONTRE LA VIOLATION DES DROITS DE PROPRIÉTÉ INTELLECTUELLE D’UN TIERS, QU’ELLE SOIT
EXPRESSE OU IMPLICITE PAR LA LOI, LE COURS DES AFFAIRES, LE COURS DE L’EXÉCUTION, L’USAGE DU
COMMERCE OU AUTREMENT. AVIS DE NON-RESPONSABILITÉ LÉGALE, VEUILLEZ
LIRE ATTENTIVEMENT. Franke Kitchen SystemsLLC vous fournit les informations ci-dessus en tant que service
public à nos clients. En accédant à ces informations et en les utilisant, vous acceptez ce qui suit et vous vous
conformez à toutes les lois applicables. Si vous n’êtes pas d’accord avec ces termes et conditions, n’utilisez pas ces
informations. Bien que nous essayions de maintenir l’information à jour, des changements peuvent avoir eu lieu
depuis sa création. Contactez votre directeur régional ou le service client pour vérifier les informations concernant
les programmes Franke Kitchen SystemsLLC et leur utilisation par vous.
Garantie limitée des hottes de cuisinière Franke/Faber:
Les hottes de cuisinière Franke/Faber sont garanties contre tout défaut de matériaux ou de fabrication pour
l’acheteur d’origine pendant une période de deux(2) ans à compter de la date d’achat d’origine lorsqu’elles sont
utilisées dans des applications intérieures résidentielles normales. Cette garantie couvre la main-d’œuvre et les
pièces de rechange. Franke, à sa discrétion, peut réparer ou remplacer le produit ou les composants nécessaires
pour remettre le produit en bon état de fonctionnement.
29
Franke Home Solutions Warranty for Franke and Faber Branded Product
Effective March 1, 2022
In the United States, Canada and Latin America, Franke warrants the Faber branded products from manufacturing defects
in material and workmanship when purchased from a Franke or Faber Authorized Retailer pursuant to product-specific
warranties detailed herein (each, a “Warranty” and collectively, the “Warranties”). The products must be properly installed,
per Franke’s installation instructions, in their original installation, and used in normal indoor residential kitchen
applications. Any products or components which have been modified or altered from their original intended condition will
void the Warranty. The Franke Warranties for Faber branded products are limited to the original purchaser and are non-
transferrable. These Warranties do not include products purchased from non-Authorized Retailers, products that are
obsolete or discontinued, or products that were previous display models. All issues with installed products are considered
warranty claims and not subject to the Return Policy. Franke reserves the right to inspect any Franke / Faber product
reported to be defective pursuant to a Warranty claim and the original installation prior to providing a replacement product
and/or component. All decisions are final. In no situation shall the liability of Franke exceed the amount of the original
purchase price.
The Warranties do not cover, and Franke shall not be liable for, any damage to products or components resulting from
misuse or abuse, accidental damages, normal wear such as scuffs, scratches or finish reduction/fading, improper
installation, abnormal usage, negligence, damage caused by improper maintenance or cleaning. Damage caused by
impurities, corrosive chemicals or acts beyond Franke’s control are not covered by any Warranty. Service calls to correct
the installation of a range hood, instructions on how to operate a range hood, to replace or repair house fuses or to correct
house wiring or plumbing are not covered by any Warranty. Service calls to repair or replace range hood light bulbs, fuses
or filters and these consumable part costs are also excluded from Warranty coverage. Installation not in accordance with
electrical or plumbing codes or Franke / Faber documentation are not covered by any Warranty. Replacement parts or
repair labor costs for units operated outside the United States, Canada or Latin America, including any non-UL or C-UL or
non-NOM approved Franke / Faber range hoods are excluded from Warranty coverage. Expenses for travel and
transportation for service in remote locations and pickup and delivery charges are not covered by any Warranty. Franke /
Faber range hoods should always be serviced in the home in their original installation.
Franke / Faber product replacements do not include liability for project delays. Product replacements are not guaranteed
to be exact replacements. If the original product is not available at the time of the warranty claim, at Franke’s option, the
product replacements will be of similar size, material, and value. Any products or components which have been modified
or altered, from its original intended condition will void the warranty.
The Warranties do not allow recovery of incidental or consequential damages such as loss of use, delay, property
damage or other consequential damage, and Franke accepts no liability for such damages. Each Warranty is limited to
the conditions set forth herein and to the applicable warranty period specified herein and is exclusive. EXCEPT FOR THE
WARRANTIES SET FORTH HEREIN, FRANKE MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE
PRODUCTS, INCLUDING, BUT NOT LIMITED TO, (1) ANY WARRANTY OF MERCHANTABILITY, (2) WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE, (3) WARRANTY OF TITLE, OR (4) WARRANTY AGAINST INFRINGEMENT
OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY, WHETHER EXPRESS OR IMPLIED BY LAW, COURSE
OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. LEGAL DISCLAIMER PLEASE
READ CAREFULLY. Franke Kitchen Systems LLC provides the above information to you as a public service to our
customers. By accessing and using this information, you agree to the following and to comply with all applicable laws. If
you do not agree with these terms and conditions, do not use this information. While we try to keep the information
current, changes may have occurred since its creation. Contact your Regional Manager or Customer Service to verify
information regarding Franke Kitchen Systems LLC programs and their use by you.
Franke / Faber Range Hood Limited Warranty:
Franke / Faber range hoods are warranted against any defect in materials or workmanship for the original purchaser for a
period of two (2) years from the date of original purchase when used in standard residential indoor applications. This
warranty covers labor and replacement parts. Franke, at its option, may repair or replace the product or components
necessary to restore the product to good working condition.
Cette garantie remplace toutes les autres garanties, expresses ou implicites. Aucun employé, représentant
commercial sur le terrain ou distributeur n’est autorisé à donner des garanties au nom de Franke Kitchen
Systems, LLC.
Pour faire une réclamation au titre de la garantie d’un produit installé, veuillez contacter Franke aux
coordonnées fournies ci-dessous. Toutes les réclamations de garantie doivent inclure les éléments suivants
pour le traitement:
1. Preuve d’achat auprès d’un revendeur agréé Franke ou Faber
2. Nom, adresse (ville, état, code postal) de l’acheteur d’origine, adresse de courrier électronique et
numéro de téléphone
3. Modèle et numéro de série Franke/Faber
4. Date d’installation
5. Description du défaut
6. Photos du défaut
En Amérique du Nord et en Amérique Latine:
Franke Home Solutions
À l’attention de: Warranty Department
800 Aviation Parkway
Smyrna, TN 37167
HS-Warranty.US@Franke.com
Raison sociale:
Franke Kitchen Systems LLC
30
LEA Y GUARDE ESTAS INSTRUCCIONES ANTES DE EMPEZAR
LA INSTALACIÓN DE ESTA CAMPANA
ADVERTENCIA: - PARA REDUCIR EL RIESGO DE INCENDIO DE GRASA:
A) Nunca deje las unidades de supercie desatendidas en los ajustes altos. Los
derrames por ebullición pueden causar humos y derrames de grasa que pueden
encenderse. Caliente los aceites lentamente en un ajuste bajo o medio.
B) Siempreenciendalacampanacuandococineafuegoaltooalambearalimentos
(porejemplo,CrepesSuzette,CherriesJubilee,PeppercornBeefFlambé).
C) Limpie los ventiladores frecuentemente. No se debe permitir que la grasa se acu-
muleenelventiladoroenelltro.
D) Utilice una cacerola de tamaño adecuado. Utilice siempre utensilios de cocina
apropiadosparaeltamañodelelementodesupercie.
ADVERTENCIA: - PARA REDUCIR EL RIESGO DE LESIONES A PERSONAS EN CASO
DE INCENDIO DE GRASA EN LA CAMPANA, TENGA EN CUENTA LO SIGUIENTE*:
A) APAGUE LAS LLAMAS con una tapa bien cerrada, una bandeja para galletas o una
bandeja metálica, luego apague el quemador. TENGA CUIDADO PARA EVITAR
QUEMADURAS. Si las llamas no salen inmediatamente EVACUE Y LLAME A LOS
BOMBEROS.
B) NUNCA RECOGER UNA CACEROLA EN LLAMAS - Usted puede ser quemado.
C) NO USE AGUA, incluyendo toallas húmedas o toallas - se pudiera producir una
violenta explosión de vapor.
D) Use un extintor SOLAMENTE si:
1. Usted sabe que usted tiene un extintor de la clase ABC, y sabe ya utilizarlo.
2. El incendio es pequeño y está contenido en el área donde comenzó.
3. Se está llamando a los bomberos.
4. Usted puede luchar el fuego con la espalda dirigida hacia una salida.
* Basado en "Consejos para luchas contra los incendios en las cocinas" publicado por NFPA
ADVERTENCIA - PARA REDUCIR EL RIESGO DE DESCARGAS ELÉCTRICAS O INCEN-
DIOS, no use este ventilador con ningún dispositivo de control de velocidad de estado.
ADVERTENCIA - PARA REDUCIR EL RIESGO DE INCENDIOS, DESCARGAS ELÉC-
TRICAS O LESIONES PERSONALES, OBSERVE LO SIGUIENTE:
1. Utilice esta unidad sólo en la forma prevista por el fabricante. Si tiene alguna pre-
gunta, póngase en contacto con el fabricante.
2. Antes de dar servicio o limpiar la unidad, desconecte la alimentación del panel
de servicio y bloquee los medios de desconexión del servicio para evitar que la
alimentación se conecte accidentalmente. Cuando los medios de desconexión
delservicionopuedanserbloqueados,jermementeundispositivodeaviso
prominente, tal como una etiqueta, al panel de servicio.
PRECAUCIÓN: Para uso general de ventilación solamente. No utilizar para el escape
de materiales peligrosos o explosivos y vapores.
ADVERTENCIA - PARA REDUCIR EL RIESGO DE INCENDIOS, DESCARGAS ELÉC-
TRICAS O LESIONES PERSONALES, OBSERVE LO SIGUIENTE:
1. Lainstalaciónyelcableadoeléctricodebenserhechosporpersonalcalicadode
acuerdo con todos los códigos y estándares aplicables, incluyendo la construcción
según normas anti-incendio.
2. Senecesitasucienteaireparalacombustiónyelagotamientoadecuadosde
los gases a través de la chimenea del equipo de combustión de combustible para
evitarelcontraujo.Sigalasdirectricesdelfabricantedelequipodecalefaccióny
las normas de seguridad tales como los publicados por la National Fire Protection
Association(NFPA),laAmericanSocietyforHeating,RefrigerationandAirCondi-
tioningEngineers(ASHRAE)ylasautoridadesdeloscódigoslocales.
31
3. Al cortar o perforar la pared o el techo, no dañe el cableado eléctrico ni otros
servicios ocultos.
4. Los ventiladores con conductos siempre deben tener salida al exterior.
TODAS LAS ABERTURAS DE LA PARED Y EL PISO DONDE ESTÁ INSTALADA LA
CAMPANA SE DEBEN SELLAR.
Esta campana requiere por lo menos 24 "de espacio libre entre el fondo de la campana y la
supercie de cocción o encimera. Esta campana ha sido aprobada por UL a esta distancia
del plano de cocción.
Esta distancia mínima puede ser mayor dependiendo de los códigos de construcción locales.
Para los planos de cocción de gas y las cocinas combinadas, se recomienda y puede ser
necesario un mínimo de 30".
Los gabinetes de arriba a ambos lados de esta unidad deben estar a un mínimo de 18" por
encima de la supercie de cocción o encimera. Consulte las instrucciones de instalación del
plano de cocción o de la cocina dadas por el fabricante antes de realizar cualquier recorte.
INSTALACIÓN EN CASA MÓVIL La instalación de esta campana debe cumplir con las
Normas de Construcción y Seguridad de Viviendas Manufacturadas, Título 24 CFR, Parte
3280 (anteriormente Normal Federal para la Construcción y seguridad de las Viviendas Móviles,
Título 24, HUD, parte 280). Vea Requisitos eléctricos.
• El sistema de ventilación DEBE terminar fuera del hogar.
• NO termine el conducto en un espacio ático o en otro espacio cerrado.
• NOuse tapas de pared de tipo colada de 4".
• NO se recomiendan conductos exibles.
• NOobstruya el ujo de aire de combustión y ventilación.
• El incumplimiento de los requisitos de ventilación puede provocar un incendio.
ADVERTENCIA
!
REQUISITOS DE VENTILACIÓN
Determine qué método de ventilación es mejor para su aplicación. Los conductos pueden exten-
derse a través de la pared o el techo.
La longitud de los conductos y la cantidad de codos se deben mantener al mínimo para proporcionar
un rendimiento eciente. El tamaño de los conductos debe ser uniforme. No instale dos codos
juntos. Use cinta adhesiva para sellar todas las juntas en el sistema de conductos. Use masilla
para sellar la pared exterior o la abertura del piso alrededor de la tapa.
NO se recomiendan conductos flexibles. Los conductos flexibles crean una contrapresión y turbu-
lencias de aire que reducen en gran medida el rendimiento.
Asegúrese de que haya espacio libre adecuado dentro de la pared o el piso para el conducto de
escape antes de hacer los cortes. No corte una viga o un poste a menos que sea absolutamente
necesario. Si se debe cortar una vigueta o poste, entonces se debe construir un marco de soporte.
ADVERTENCIA - Para reducir el riesgo de incendio, use solamente conductos de metal.
PRECAUCIÓN - Para reducir el riesgo de incendio y para descargar adecuadamente el
aire, asegúrese de sacar el aire - No expulse los humos en espacios dentro de paredes
o techos, áticos, espacios angostos o garajes.
Instalaciones para clima frío
Se debe instalar un registro de retrogresión adicional para minimizar el ujo de aire frío hacia
atrás y se debe instalar un interruptor térmico no metálico para minimizar la conducción de
temperaturas externas como parte del sistema de ventilación. El registro debe estar en el lado
del aire frío del interruptor térmico. El interruptor debe estar lo más cerca posible de donde el
sistema de ventilación ingrese a la parte calentada de la casa.
32
• Esta campana requiere conexión eléctrica de tierra.
• Si la tubería de agua fría está interrumpida por juntas de plástico, de materiales no
metálicos u otros materiales, NO la utilice para conexión a tierra.
• NO conecte a tierra a una tubería de gas.
• NO tenga un fusible en el circuito neutro o de tierra. Un fusible en el circuito neutro o
de tierra podría provocar una descarga eléctrica.
• Consulte con un electricista calicado si tiene dudas acerca de si la campana está
correctamente conectada a tierra.
• El incumplimiento de los requisitos eléctricos puede provocar un incendio.
ADVERTENCIA
!
REQUISITOS ELÉCTRICOS
Se requiere un suministro eléctrico de 120 voltios, 60 Hz solo CA en un circuito separado
con fusible de 15 amperios. Se recomienda un fusible de retardo o un cortacircuitos. El
fusible se debe dimensionar según los códigos locales de acuerdo con la clasicación
eléctrica de esta unidad, tal como se especica en la placa de número de serie/clasi-
cación ubicada dentro de la unidad, cerca del compartimiento de cableado de campo.
33
RECORTE
DIMENSIONES DE CRISTAL HC
OPCIONES DE MOLDURA DELANTERA
Cristal HC tiene una tira de acero inoxidable instalada. Existen kits opcionales de color blanco y negro para su compra.
Para tener una tira delantera personalizada, puede contactar con una tienda de armarios local que puede hacer una tira compatible con sus armarios.
DIMENSIONES DE LA TIRA DELANTERA PERSONALIZADA.
1 15/32"
3/4"
29 7/8" or 35 7/8"
25 1/2” - 31 1/2”
10”
25 1/2” - 31 1/2”
13/16”
17 1/2” - 23 1/2”
5 7/8”
Planificación previa de su instalación - Importante: La altura recomendada para instalar esta campana arriba de la
encimera es de un mínimo de 24 " y un máximo de 30" para una eficacia máxima. También consulte la recomendación
del fabricante de la encimera. NOTA: Si hay ventilación trasera directa, utilice el diagrama dimensional lateral de abajo
a la derecha. Para la ventilación superior (en esta posición viene de serie), utilice el diagrama dimensional izquierdo.
Consulte la página 5 para obtener instrucciones sobre la ventilación trasera directa.
3 15/16”
DIMENSIONES LATERALES DE CRISTAL HC
(VENTILACIÓN SUPERIOR - ESTÁNDAR)
DIMENSIONES LATERALES DE CRISTAL HC
(OPCIÓN DE VENTILACIÓN TRASERA DIRECTA)
3 15/16”
34
CAMPANA 36" - INFORMACIÓN POSTERIOR
CAMPANA 30" - INFORMACIÓN POSTERIOR
DRAFT 25-MAY-2020 18:52
Palazzi, Walter
15-Nov-2019
Released
= =
DRAFT 25-MAY-2020 18:52
DRAFT 25-MAY-2020 18:52
35
Version 06/14 - Page 5
9.0 pies
10.0 pies
0.0 pies
19.0 pies
HERRAMIENTAS NECESARIAS PARA LA INSTALACIÓN
•Sierra de sable o sierra de calar
•Taladro
•Broca de madera de 1 1/4 "
•Alicates
•Destornillador Phillips
•Pelacables o cuchillo de uso general
•Tijeras de metal
•Cinta métrica o regla
•Nivel
•Lápiz
•Pistola de calafateo
•Cinta adhesiva
PIEZAS SUMINISTRADAS PARA LA INSTALACIÓN
PIEZAS NECESARIAS PARA LA INSTALACIÓN
•2 Conectores de conducto
•Cable de suministro de energía
•1 Tapa de pared o techo
•Todos los conductos metálicos
PLANEAR EL CONDUCTO
INSTALACIONES DE RECIRCULACIÓN
Para las instalaciones de recirculación (FIGURA 3), se necesitan filtros de carbón. Retire los cuatro filtros de grasa y reserve. Conecte un filtro de carbón a
cada extremo del soplador. Cada filtro de carbón se conecta a la rejilla negra en el costado del ventilador. Gire el filtro en el sentido horario para instalarlo
y en sentido antihorario para extraerlo (FIGURA 3A). Reemplace los cuatro filtros de grasa. Algunos conductos deben ser instalados para que la campana
extraíble vuelva a la cocina, ya sea en la parte superior del gabinete o en la cara del techo. Para cubrir la abertura del conducto se puede utilizar una rejilla
de ventilación de plástico (FIGURA 3B) suministrada con la campana. Este trabajo de conductos no debe terminar en un espacio de aire muerto.
FIGURE 3A
45˚ Codo
90˚ Codo
90˚ Codo plano
Tapa de pared
FIGURE A
9 pies de conducto recto
2 - 90˚ Codos
Tapa de pared
Sistema total
FIGURE B
3.0 pies
5.0 pies
12.0 pies
0.0 pies
CONDUCTO
VERTICAL
FIGURE 2
CONDUCTO
HORIZONTAL
FIGURE 1
Para la ventilación trasera directa (FIGURA 2), debe
cambiar la posición del ventilador. Retire los 12 tornillos
que sujetan la carcasa de metal al cuerpo de la campana.
Retire los 4 tornillos que sujetan la carcasa del ventilador
a la carcasa de metal. Gire el soplador 90 grados hacia la
parte posterior y luego gírelo 180 grados. Asegúrese de
que el cable de alimentación esté colocado correctamente.
Reemplace todos los tornillos, asegurándose de que estén
firmemente sujetos.
armario
techo
Conducto redondo de 6"
campana
armario
techo
Conducto redondo de 6"
campana
rejilla de ventilación
rejilla de ventilación
FIGURE 3B
FIGURE 3
Para un rendimiento satisfactorio, el recorrido del conducto
no debe exceder los 50 pies equivalentes si se conducen
utilizando el conducto redondo mínimo requerido de 6".
En la figura A se indican los pies equivalentes para cada
pieza de conducto en el sistema. Un ejemplo se da en la
FIGURA B. Para mejores resultados, no use más de tres
codos de 90°. Asegúrese de que haya un mínimo de 24 "
de conducto recto entre los codos si se usa más de uno.
No instales dos codos juntos. Si debe colocar el codo
inmediatamente, hágalo tan lejos de la abertura de escape
de la campana como sea posible.
•1 Amortiguador de contraflujo
•1 Rejilla de ventilación (sólo para instalaciones de recirculación)
•1 Moldura de vinilo
•1 Paquete de literatura
La gama de campanas deslizantes Cristal HC está diseñada para ofrecer una amplia flexibilidad
de instalación. La campana puede ser canalizada vertical u horizontalmente a través de una
ventilación redonda de 6". La unidad también se puede instalar en una configuración de recirculación.
La unidad viene de serie en la posición de ventilación superior. Las FIGURAS 1 y 2 muestran
instalaciones verticales y horizontales para esta unidad. La FIGURA 3 muestra la instalación de
recirculación.
La Cristal HC requiere conductos redondos de 6". Para asegurar que el ventilador funcione al máximo
de su capacidad, los conductos deben ser tan cortos y rectos como sea posible.
plafón
36
ACCESORIOS OPCIONALES PARA LA COMPRA POR SEPARADO ACCESORIOS
• Filtros de carbón
Parainstalacionessinventilaciónsolamente,reemplacelosltrosdecarbónsegúnseanecesarioparte#
FILTER1-#FILTER1LL
• Kit reductor de CFM
Parareducirlacfmamenosde300cfmparausoenambientesdeairedereposiciónparte#CFMRED
• Amortiguador de aire de reposición universal 6".
Devuelve el aire fresco a la casa a través de un amortiguador automático cuando la campana está encendi-
da#MUDAMPER6
37
INSTALE LA CAMPANA
1.Retire la tapa protectora de la campana y colóquela sobre una superficie
plana. Cubra la superficie para evitar daños accidentales. Retire todas las
piezas, incluyendo el amortiguador de contraflujo, la rejilla de plástico y el
paquete de documentación antes de desechar el cartón. Retirar los filtros
de grasa y déjelos a un lado.
2.Coloque el amortiguador redondo en la abertura de escape de la campana
y presione hacia abajo.
FIGURE 5
3.La campana se monta en el armario por medio de dos soportes cargados
con resortes, uno a cada lado de la campana (FIGURA 6). Levante la campana
hasta la abertura de corte en el armario. Tenga cuidado de no dañar el gabinete, l
a campana u otros dispositivos.
RECORTE
PREPARARA EL ARMARIO
1.Desconecte y mueva el rango independiente de la apertura del armario para facilitar
el acceso al armario superior y a la pared posterior. Coloque una cubierta gruesa y
protectora sobre las encimeras de cocción, los rangos de ajuste o las encimeras para
protegerlas de daños o suciedad.
2.Determine y marque claramente con un lápiz la línea central del armario en la pared
y en la parte inferior del armario, donde se instalará la campana.
3.Si el fondo del armario está empotrado, se deben instalar bloques de madera para
asegurar una alineación apropiada con el fondo del armario. Los bloques de madera
deben estar a ras o empotrados de 1/16" a 1/8" dentro de la parte inferior del armario
como se indica en la FIGURA 4.
FIGURE 4
HAGA LA ABERTURA DE RECORTE (FIGURA 5) DONDE
SE INSTALARÁ LA CAMPANA.
4.Determine los recortes apropiados para los conductos. Haga todos los cortes
necesarios en las paredes o armario para los conductos. Instale la red de
conductos antes de montar la campana.
5.Determine y realice el corte adecuado para el cable de alimentación.
Utilice una broca de 1 1/4" para hacer este agujero. Pase el cable de suministro
de energía a través de la pared o el armario. NO encienda la unidad hasta que
se haya completado la instalación. Use la masilla para sellar alrededor de la
abertura del cable.
FIGURE 6
4.Los soportes cargados por resorte se ajustan en fábrica para acomodar
un grosor entre 1 3/16" y 2 1/4". Si el fondo de su armario tiene un grosor
inferior a 1 3/16", los soportes cargados por resorte se pueden retirar y
reposicionar desde el ajuste superior hasta el ajuste inferior quitando los
cuatro tornillos phillips.
5.Apriete la campana al armario girando los tornillos con un destornillador
phillips.
6.Se incluye una tira de vinilo gris (FIGURA 7) para cubrir la parte inferior
de cualquier armario expuesto restante. Coloque la tira de vinilo gris en la
parte inferior trasera de la campana con los tres tornillos provistos. Si es
necesario, la tira se puede cortar para adaptarse a la profundidad del
armario.
FIGURE 7
TIRA DE VINILO
25 1/2” - 31 1/2”
10”
25 1/2” - 31 1/2”
13/16”
17 1/2” - 23 1/2”
5 7/8”
TIRAS DE RELLENO DE MADERA
Instalación de ventilación con
conductos
Instale la aleta del regulador que se incluye con la
campana extractora como se muestra.
38
7
Accesorio de caja de cableado
de conexión directa sku #
WIREBOX
(comprado por separado)
Created by
-
Denomination
-
Lang EN Sheet
1
/1
Modif.by
Approved by
Approval date
Doc. status
Drawing N.
NEW_DRAWING_BOX
Rev
01
INSTALACIÓN ELÉCTRICA CON CAJA DE
CABLEADO OPCIONAL
Para la instalación de cableado permanente: utilice
solo con el kit de caja de cableado de la campana
que se incluye
sku # WIREBOX, fabricado por Faber.
Max. 33 7/16”
INSTRUCCIONES DE CONEXIÓN A TIERRA Este aparato debe estar
conectado a tierra. En el caso de un cortocircuito eléctrico, la conexión
a tierra reduce el riesgo de descarga eléctrica al proporcionar un cable
de escape para la corriente eléctrica. Este equipo está provisto de
un cable que tiene un cable de conexión a tierra con un enchufe de
conexión a tierra. El enchufe debe estar enchufado a un tomacorriente
que esté instalado y conectado a tierra correctamente.
ADVERTENCIA: una conexión a tierra incorrecta puede provocar un
riesgo de descarga eléctrica.
Consulte a un electricista calicado si las instrucciones de conexión a
tierra no se comprenden completamente o si existe una duda acerca
de si el equipo está correctamente conectado a tierra.
No utilice un cable de extensión. Si el cable de alimentación es
demasiado corto, solicite a un electricista calicado que instale un
tomacorriente cerca del dispositivo.
INSTALACIÓN ELÉCTRICA
CON CABLE DE CONEXIÓN
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/O Switch
TheOn/O switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light o.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower o.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut o when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is o, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The New Cristal comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
FIGURE 8
1 15/32"
FIGURE 9
3/4"
29 7/8" or 35 7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/O Switch
TheOn/O switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light o.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower o.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut o when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is o, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The New Cristal comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9 .
FIGURE 8
1
15/32"
FIGURE 9
3/4"
29
7/8"
or 35
7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
OPCIONES DE MOLDURA FRONTAL
New Cristal viene con una tira frontal de acero inoxidable instalada. Para
cambiar la tira frontal, retire los tres tornillos Phillips situados detrás de la
tira (FIGURA 8). Si es necesario, la tira frontal se puede ajustar aojando
los tres tornillos Phillips y deslizando la tira hacia arriba o hacia abajo.
Apriete los tornillos cuando tenga la tira colocada correctamente.
Para una tira frontal personalizada, una tienda local de gabinetes puede
hacer una tira que combine con sus gabinetes. Las dimensiones de la
tira frontal se dan en la FIGURA 9.
Tira delantera
Visera
Tres tornillos
39
INFORMACIÓN DE USO Y CUIDADO
Para mejores resultados
Encienda la campana varios minutos antes de cocinar para desarrollar un ujo de aire ade-
cuado. Deje que la campana funcione durante varios minutos después de que se complete
la cocción para eliminar todo el humo y los olores de la cocina.
Version 06/14 - Page 8
USE AND CARE INFORMATION
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/Off Switch
TheOn/Off switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light off.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower off.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut off when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
proper airow. Allow the unit to operate for several minutes
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
The metal grease lters should be cleaned frequently in hot
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water. Using abrasives and scouring
agents can scratch rangehood nishes and should not be
used to clean nished surfaces.
Replacing the halogen lamp
CAUTION the bulb MAY BE HOT
To replace the halogen bulb, see (Figure 11)
Before attempting to replace the lamp, make sure the light
switch is off, the bulb CAUTION may be hot. Remove the
cover snap-on lamp levering under the metal ring, supporting
it with one hand. Remove the halogen lamp from the lamp
holder by pulling gently. Replace the lamp with a new one of
the same type, making sure that you insert the two pins into
the slots on the lamp holder. Replace the cover snap-on lamp.
FIGURE 10
FRONT TRIM OPTIONS
The Cristal HC comes with a stainless front strip installed.
Optional black and white strips are available as accessories
for purchase. To change the front strip, remove the three phil-
lips screws located behind the strip (FIGURE 8). If necessary,
the front strip can be adjusted by loosening the three phillips
screws and sliding the strip up or down. Tighten screws when
you have the strip properly placed.
For a custom front strip, a local cabinet shop can make a strip
to match your cabinets. The front strip dimensions are given
in FIGURE 9.
FIGURE 8
1 15/32"
FIGURE 9
3/4"
29 7/8" or 35 7/8"
Visor
Front
Strip
Three Screws
B
2x
FIGURE 11
INFORMACIÓN DE USO Y CUIDADO
Panel de control de la campana
Todos los controles están ubicados en el lado derecho de la campana.
Interruptor de encendido / apagado de la luz
El interruptor de encendido / apagado de la luz halógena se encuentra detrás del borde delantero. Al mover el
interruptor a la posición 1, se enciende la luz. Al mover el interruptor a la posición 0, se apaga la luz.
Interruptor de velocidad del ventilador
B en la FIGURA 10 muestra el interruptor de control de velocidad del ventilador. Al mover el interruptor a la
posición 1, el ventilador se enciende en BAJO. Al mover el interruptor a la posición 2, el ventilador se enciende
en MEDIO. Al mover el interruptor a la posición 3, el ventilador se enciende en ALTO. Al mover el interruptor a
la posición 0, el ventilador se apague.
Operación automática
Mientras el ventilador y los interruptores de luz estén encendidos, el ventilador y la luz funcionarán automática-
mente cuando se abra la visera y se apaga cuando la visera se cierre.
40
Limpiezadelosltrosdegrasametálicos
Los ltros de grasa metálicos se pueden limpiar en solución
de detergente caliente o lavarse en el lavavajillas. Se deben
limpiar cada 2 meses de uso, o más frecuentemente si el uso
es particularmente pesado.
• Abra la visera tirando de ella.
• Retire el ltro, empujando la palanca hacia la parte posterior
de la unidad y al mismo tiempo tirando hacia abajo.
• Lave el ltro sin doblarlo, deje que se seque completamente
antes de reemplazarlo (si la supercie del ltro cambia de color
con el tiempo, esto no tendrá ningún efecto sobre su eciencia).
• Reemplace, asegurándose de que el asa esté orientada
hacia adelante.
• La limpieza en el lavavajillas puede estropear el acabado del
ltro de grasa metálico.
• Cierra la visera.
Reemplazodelltrodecarbónactivado
Los ltros de carbón activado no son lavables y no pueden
ser regenerados, y deben ser reemplazados aproximadamente
cada 4 meses de operación, o más frecuentemente con uso
intensivo.
• Abra la visera tirando de ella.
• Retire el ltro, empujándolo hacia la parte posterior de la
unidad y al mismo tiempo tirando hacia abajo.
• Retire los ltros saturados de carbón activado, como se
indica (A).
• Coloque los nuevos ltros, como se indica (B).
• Reemplace, teniendo cuidado de asegurarse de que la manija
mire hacia adelante.
• Cierra la visera.
EN 7
7
INSTALLATION
Fitting the Hood canopy
BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:
• Disconnect the wires to the Commands at the connectors.
• Disconnect the wires to the Light at the con-
nectors.
• The Hood can be installed directly on the
underside of the wall unit (Minimum 650 mm
from the Cooker Hob).
• Create an opening in the bottom of the wall unit,
as shown.
• Insert the hood until the side supports snap into
place.
• Fasten using the 10 screws 12a provided.
• Lock in position by tightening the screws Vf from
underneath the hood.
• Open the suction panel by turning the specific knob.
• Disconnect the panel from the hood canopy by sliding the
fixing pin lever.
• Remove grease filters.
• Screw the Frame into place
using the 6 screws 12f, re-
connect the wires to the
Commands and Light, re-
place the metal grease filter
and the Panel.
260
13
495 - 675
Lámparas LED de lastre
integrado de tipo Gu10
- Cumple con
UL 1993 / nmx-
j-578/1-ance /
csa c22.2 No
1993
Sistema de iluminación
• Apague el suministro eléctrico antes de
reemplazar las bombillas, y asegúrese
de que las bombillas estén frías al tacto
antes de continuar.
• Retire la lámpara en la base, gírela
ligeramente hacia la izquierda, extrái-
gala del conector y gírela ligeramente
hacia la izquierda.
• Reemplace la lámpara por una nueva
del mismo tipo, asegurándose de in-
sertar las dos clavijas correctamente
en los alojamientos del portalámparas.
• Una vez que los pernos de la bombilla
estén en su lugar, gire ligeramente
hacia la derecha para asegurar.
41
Diagrama de cableado
0123456789
R
P
P
H90_496 01
Drawing N : Rev :
Modif. by
Doc.status
Do not get quotas from the drawing do not bring
modifications without authorization of techincal office.
According to the law we reserve the own of the present
drawing with reproduction prohibition partial or total.
Approved date
Modification description
Approved by
WIRING DIAGRAM M8_4V SCL HV LED
Doc Type
Denomination
Creation date
02.Mar.2018
DOLCE CORRADO
Created by
991.0520.839
Code
LED
0
1
SW3
LED
RV
CN3
RED (org)
VLT(org)
LB WH A GR
CN2
WHT
WHT
BRW
BLU
0 1 2 3
SW2
RED
123
654
789
PNK
BLU
PNK
BK BR
CN1
RED
BRW
SIDE
INSERT
CABLE
SW1
BLK
123
654
987
PNK
M8-4V
BRW
ORG
M1
WHT
BLU
BLK
GRY
6,3uF
Y-G
WHT
220-240V ~ 50Hz
110-127V ~ 60Hz
220 ~ 60Hz
Y-G
BLK
42
GARANTÍA
Franke Home Solutions Warranty for Franke and Faber Branded Product
Effective March 1, 2022
In the United States, Canada and Latin America, Franke warrants the Faber branded products from manufacturing defects
in material and workmanship when purchased from a Franke or Faber Authorized Retailer pursuant to product-specific
warranties detailed herein (each, a “Warranty” and collectively, the “Warranties”). The products must be properly installed,
per Franke’s installation instructions, in their original installation, and used in normal indoor residential kitchen
applications. Any products or components which have been modified or altered from their original intended condition will
void the Warranty. The Franke Warranties for Faber branded products are limited to the original purchaser and are non-
transferrable. These Warranties do not include products purchased from non-Authorized Retailers, products that are
obsolete or discontinued, or products that were previous display models. All issues with installed products are considered
warranty claims and not subject to the Return Policy. Franke reserves the right to inspect any Franke / Faber product
reported to be defective pursuant to a Warranty claim and the original installation prior to providing a replacement product
and/or component. All decisions are final. In no situation shall the liability of Franke exceed the amount of the original
purchase price.
The Warranties do not cover, and Franke shall not be liable for, any damage to products or components resulting from
misuse or abuse, accidental damages, normal wear such as scuffs, scratches or finish reduction/fading, improper
installation, abnormal usage, negligence, damage caused by improper maintenance or cleaning. Damage caused by
impurities, corrosive chemicals or acts beyond Franke’s control are not covered by any Warranty. Service calls to correct
the installation of a range hood, instructions on how to operate a range hood, to replace or repair house fuses or to correct
house wiring or plumbing are not covered by any Warranty. Service calls to repair or replace range hood light bulbs, fuses
or filters and these consumable part costs are also excluded from Warranty coverage. Installation not in accordance with
electrical or plumbing codes or Franke / Faber documentation are not covered by any Warranty. Replacement parts or
repair labor costs for units operated outside the United States, Canada or Latin America, including any non-UL or C-UL or
non-NOM approved Franke / Faber range hoods are excluded from Warranty coverage. Expenses for travel and
transportation for service in remote locations and pickup and delivery charges are not covered by any Warranty. Franke /
Faber range hoods should always be serviced in the home in their original installation.
Franke / Faber product replacements do not include liability for project delays. Product replacements are not guaranteed
to be exact replacements. If the original product is not available at the time of the warranty claim, at Franke’s option, the
product replacements will be of similar size, material, and value. Any products or components which have been modified
or altered, from its original intended condition will void the warranty.
The Warranties do not allow recovery of incidental or consequential damages such as loss of use, delay, property
damage or other consequential damage, and Franke accepts no liability for such damages. Each Warranty is limited to
the conditions set forth herein and to the applicable warranty period specified herein and is exclusive. EXCEPT FOR THE
WARRANTIES SET FORTH HEREIN, FRANKE MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE
PRODUCTS, INCLUDING, BUT NOT LIMITED TO, (1) ANY WARRANTY OF MERCHANTABILITY, (2) WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE, (3) WARRANTY OF TITLE, OR (4) WARRANTY AGAINST INFRINGEMENT
OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY, WHETHER EXPRESS OR IMPLIED BY LAW, COURSE
OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. LEGAL DISCLAIMER PLEASE
READ CAREFULLY. Franke Kitchen Systems LLC provides the above information to you as a public service to our
customers. By accessing and using this information, you agree to the following and to comply with all applicable laws. If
you do not agree with these terms and conditions, do not use this information. While we try to keep the information
current, changes may have occurred since its creation. Contact your Regional Manager or Customer Service to verify
information regarding Franke Kitchen Systems LLC programs and their use by you.
Franke / Faber Range Hood Limited Warranty:
Franke / Faber range hoods are warranted against any defect in materials or workmanship for the original purchaser for a
period of two (2) years from the date of original purchase when used in standard residential indoor applications. This
warranty covers labor and replacement parts. Franke, at its option, may repair or replace the product or components
necessary to restore the product to good working condition.
La garantía de Franke Home Solutions para los productos de las marcas Franke y Faber entra en vigor el 1 de marzo de 2022
En Estados Unidos, Canadá y América Latina, Franke garantiza los productos de la marca Faber contra defectos de fabricación
en materiales y mano de obra cuando se compran a un minorista autorizado de Franke o Faber de acuerdo con las garantías
específicas del producto que se detallan en este documento (cada una, una "Garantía" y colectivamente, las "Garantías"). Los
productos deben ser instalados correctamente, según las instrucciones de instalación de Franke, en su instalación original,
y utilizados en aplicaciones normales de cocina residencial en interiores. Cualquier producto o componente que haya sido
modificado o alterado de su condición original anulará la garantía. Las garantías de Franke para los productos de la marca Faber
están limitadas al comprador original y no son transferibles. Estas garantías no incluyen los productos comprados a minoristas no
autorizados, los productos obsoletos o descatalogados, ni los productos que eran modelos de exposición anteriores. Todos los
problemas con los productos instalados se consideran reclamaciones de garantía y no están sujetos a la política de devoluciones.
Franke se reserva el derecho de inspeccionar cualquier producto Franke / Faber reportado como defectuoso en virtud de una
reclamación de garantía y la instalación original antes de proporcionar un producto y/o componente de reemplazo. Todas las
decisiones son definitivas. En ningún caso la responsabilidad de Franke superará el importe del precio de compra original.
Las garantías no cubren, y Franke no será responsable, de ningún daño a los productos o componentes derivado de un mal uso
o abuso, daños accidentales, desgaste normal como rozaduras, arañazos o reducción/descoloramiento del acabado, instalación
incorrecta, uso anormal, negligencia, daños causados por un mantenimiento o limpieza inadecuados. Los daños causados por
impurezas, productos químicos corrosivos o actos fuera del control de Franke no están cubiertos por ninguna garantía. Las
llamadas de servicio para corregir la instalación de una campana extractora, las instrucciones sobre el funcionamiento de una
campana extractora, para sustituir o reparar los fusibles de la casa o para corregir el cableado o la fontanería de la casa no están
cubiertas por ninguna Garantía. Las llamadas de servicio para reparar o sustituir las bombillas, fusibles o filtros de la campana
extractora, así como los costes de estas piezas consumibles, también están excluidos de la cobertura de la garantía. La instalación
que no esté de acuerdo con los códigos eléctricos o de fontanería o con la documentación de Franke / Faber no está cubierta
por ninguna garantía. Los costes de las piezas de repuesto o de la mano de obra de reparación de las unidades utilizadas fuera
de los Estados Unidos, Canadá o América Latina, incluidas las campanas extractoras de cocina Franke / Faber no aprobadas por
la norma UL o C-UL, están excluidos de la cobertura de la garantía. Los gastos de viaje y transporte para el servicio en lugares
remotos y los gastos de recogida y entrega no están cubiertos por ninguna Garantía. Las campanas extractoras Franke / Faber
siempre deben ser revisadas en el hogar en su instalación original.
Las sustituciones de productos Franke / Faber no incluyen la responsabilidad por los retrasos del proyecto. No se garantiza que
las sustituciones de los productos sean exactas. Si el producto original no está disponible en el momento de la reclamación de
la garantía, a opción de Franke, los reemplazos del producto serán de tamaño, material y valor similares. Cualquier producto o
componente que haya sido modificado o alterado de su condición original anulará la garantía.
Las garantías no permiten la recuperación de los daños incidentales o indirectos, como la pérdida de uso, el retraso, los daños a la
propiedad u otros daños indirectos, y Franke no acepta ninguna responsabilidad por tales daños. Cada Garantía está limitada a las
condiciones establecidas en el presente documento y al período de garantía aplicable especificado en el mismo y es exclusiva. A
EXCEPCIÓN DE LAS GARANTÍAS ESTABLECIDAS EN ESTE DOCUMENTO, FRANKE NO OFRECE NINGUNA GARANTÍA CON
RESPECTO A LOS PRODUCTOS, INCLUYENDO, PERO NO LIMITADO A, (1) CUALQUIER GARANTÍA DE COMERCIALIZACIÓN,
(2) LA GARANTÍA DE IDONEIDAD PARA UN PROPÓSITO PARTICULAR, (3) LA GARANTÍA DE TÍTULO, O (4) LA GARANTÍA
CONTRA LA VIOLACIÓN DE LOS DERECHOS DE PROPIEDAD INTELECTUAL DE UN TERCERO, YA SEA EXPRESA O
IMPLÍCITA POR LA LEY, EL DESARROLLO DE LOS NEGOCIOS, EL DESARROLLO DE LA EJECUCIÓN, EL USO DEL COMERCIO
O DE OTRA MANERA. AVISO LEGAL POR FAVOR
LEA ATENTAMENTE. Franke Kitchen Systems LLC le proporciona la información anterior como un servicio público a nuestros
clientes. Al acceder y utilizar esta información, usted acepta lo siguiente y el cumplimiento de todas las leyes aplicables. Si no está
de acuerdo con estas condiciones, no utilice esta información. Aunque intentamos mantener la información actualizada, pueden
haberse producido cambios desde su creación. Póngase en contacto con su gerente regional o con el servicio de atención al
cliente para verificar la información relativa a los programas de Franke Kitchen Systems LLC y su uso.
Garantía limitada de la campana extractora Franke / Faber:
Las campanas extractoras de Franke / Faber están garantizadas contra cualquier defecto de materiales o mano de obra
para el comprador original durante un período de dos (2) años a partir de la fecha de compra original cuando se utilizan en
aplicaciones residenciales estándar de interior. Esta garantía cubre la mano de obra y las piezas de recambio. Franke, a su elección,
puede reparar o sustituir el producto o los componentes necesarios para restablecer el producto en buenas condiciones de
funcionamiento.
43
Franke Home Solutions Warranty for Franke and Faber Branded Product
Effective March 1, 2022
In the United States, Canada and Latin America, Franke warrants the Faber branded products from manufacturing defects
in material and workmanship when purchased from a Franke or Faber Authorized Retailer pursuant to product-specific
warranties detailed herein (each, a “Warranty” and collectively, the “Warranties”). The products must be properly installed,
per Franke’s installation instructions, in their original installation, and used in normal indoor residential kitchen
applications. Any products or components which have been modified or altered from their original intended condition will
void the Warranty. The Franke Warranties for Faber branded products are limited to the original purchaser and are non-
transferrable. These Warranties do not include products purchased from non-Authorized Retailers, products that are
obsolete or discontinued, or products that were previous display models. All issues with installed products are considered
warranty claims and not subject to the Return Policy. Franke reserves the right to inspect any Franke / Faber product
reported to be defective pursuant to a Warranty claim and the original installation prior to providing a replacement product
and/or component. All decisions are final. In no situation shall the liability of Franke exceed the amount of the original
purchase price.
The Warranties do not cover, and Franke shall not be liable for, any damage to products or components resulting from
misuse or abuse, accidental damages, normal wear such as scuffs, scratches or finish reduction/fading, improper
installation, abnormal usage, negligence, damage caused by improper maintenance or cleaning. Damage caused by
impurities, corrosive chemicals or acts beyond Franke’s control are not covered by any Warranty. Service calls to correct
the installation of a range hood, instructions on how to operate a range hood, to replace or repair house fuses or to correct
house wiring or plumbing are not covered by any Warranty. Service calls to repair or replace range hood light bulbs, fuses
or filters and these consumable part costs are also excluded from Warranty coverage. Installation not in accordance with
electrical or plumbing codes or Franke / Faber documentation are not covered by any Warranty. Replacement parts or
repair labor costs for units operated outside the United States, Canada or Latin America, including any non-UL or C-UL or
non-NOM approved Franke / Faber range hoods are excluded from Warranty coverage. Expenses for travel and
transportation for service in remote locations and pickup and delivery charges are not covered by any Warranty. Franke /
Faber range hoods should always be serviced in the home in their original installation.
Franke / Faber product replacements do not include liability for project delays. Product replacements are not guaranteed
to be exact replacements. If the original product is not available at the time of the warranty claim, at Franke’s option, the
product replacements will be of similar size, material, and value. Any products or components which have been modified
or altered, from its original intended condition will void the warranty.
The Warranties do not allow recovery of incidental or consequential damages such as loss of use, delay, property
damage or other consequential damage, and Franke accepts no liability for such damages. Each Warranty is limited to
the conditions set forth herein and to the applicable warranty period specified herein and is exclusive. EXCEPT FOR THE
WARRANTIES SET FORTH HEREIN, FRANKE MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE
PRODUCTS, INCLUDING, BUT NOT LIMITED TO, (1) ANY WARRANTY OF MERCHANTABILITY, (2) WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE, (3) WARRANTY OF TITLE, OR (4) WARRANTY AGAINST INFRINGEMENT
OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY, WHETHER EXPRESS OR IMPLIED BY LAW, COURSE
OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. LEGAL DISCLAIMER PLEASE
READ CAREFULLY. Franke Kitchen Systems LLC provides the above information to you as a public service to our
customers. By accessing and using this information, you agree to the following and to comply with all applicable laws. If
you do not agree with these terms and conditions, do not use this information. While we try to keep the information
current, changes may have occurred since its creation. Contact your Regional Manager or Customer Service to verify
information regarding Franke Kitchen Systems LLC programs and their use by you.
Franke / Faber Range Hood Limited Warranty:
Franke / Faber range hoods are warranted against any defect in materials or workmanship for the original purchaser for a
period of two (2) years from the date of original purchase when used in standard residential indoor applications. This
warranty covers labor and replacement parts. Franke, at its option, may repair or replace the product or components
necessary to restore the product to good working condition.
Esta garantía sustituye a todas las demás garantías, expresas o implícitas. Ningún empleado, representante
de ventas de campo o distribuidor está autorizado a dar ninguna garantía en nombre de Franke Kitchen
Systems, LLC
Para reclamar la garantía de un producto instalado, póngase en contacto con Franke a través de la
información de contacto proporcionada a continuación. Todos los reclamos de garantía deben incluir lo
siguiente para su procesamiento:
1. Prueba de compra en un distribuidor autorizado de Franke o Faber
2. Nombre del comprador original, dirección (incluyendo ciudad, estado y código postal), dirección de
correo electrónico y número de teléfono
3. Modelo y número de serie de Franke / Faber
4. Fecha de instalación
5. Descripción del defecto
6. Fotos del defecto
En América del Norte y América Latina:
Soluciones para el hogar Franke
A la atención de: Departamento de Garantía
800 Aviation Parkway
Smyrna, TN 37167
HS-Warranty.US@Franke.com
Persona jurídica:
Franke Kitchen Systems LLC
991.0526.707_11 - 230510 - D000000004196_10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Faber Cristal 30 SS 400 cfm Guía de instalación

Faber
Marca
Faber
Modelo
Cristal 30 SS 400 cfm
Categoría
Campanas de cocina
Tipo
Guía de instalación
Este manual también es adecuado para
Descargar PDF
informe

En otros idiomas