Transcripción de documentos

-Pro- 10M250 SOUND REINFORCEMENT This 10” high efficiency loudspeaker is designed to cover the mid frequencies range with smooth response, low harmonic distortion and excellent power capacity. It features a 2,5” voice coil diameter, edgewound flat aluminium wire, and a massive, powerful magnet system. The motor assembly generates a uniform magnetic field, and provides an efficient thermal path, which contributes to dissipate the heat produced by the voice coil. Este modelo de 10” de alta eficiencia está diseñado para reproducir el rango de frecuencias medias con una respuesta consistente y extensa, baja distorsión armónica y excelente capacidad de potencia. Está dotado de una bobina de 2”1/2 realizada con hilo plano de aluminio y movida por un potente conjunto magnético generador de un campo simétrico y capaz de disipar eficazmente el calor producido por la bobina. PREDICTED LOW FREQUENCY RESPONSE • Bass-reflex cabinet, Vb=50.00 I, fb=70.0 Hz SPECIFICATIONS Nominal diameter 250 mm. 10 in. Rated impedance 8 ohms. Power capacity* 250 w RMS Program Power 500 Watts. Sensitivity 99 dB, 2.83v @ 1m @ 2π Frequency range 30-5500 Hz Recom. enclosure vol. 30/80 l 1.05/2.8 ft.3 Voice coil diameter 62.4 mm. 2.5 in. Magnetic assembly weight 6.4 kg. 14.08 lb. BL factor 16 N/A Moving mass 0.032 kg. Voice coil length 16 mm. Air gap height 9 mm. X damage (peak to peak) 30 mm. MOUNTING INFORMATION Overall diameter Bolt circle diameter Baffle cutout diameter: -Front mount -Rear mount Depth Volume displaced by driver Net weight Shipping weight 270 mm. 10.62 in. 255 mm. 10.03 in. FREQUENCY RESPONSE & DISTORTION CURVES, MAGN. On axis, 1w @ 1m. TIME RESPONSE, MAGN. FREQUENCY RESPONSE, PHASE. On axis, 1w @ 1m. FREE AIR IMPEDANCE CURVE VOICE COIL INDUCTANCE CURVE Re + Red(w) CURVE 240 mm. 9.45 in. 230 mm. 9.05 in. 116 mm. 4.56 in. 3 l 0.10 ft.3 7 kg. 15.4 lb. 7.4 kg. 16.28 lb. MATERIALS Basket Cone Surround Voice coil Magnet Cast aluminium Paper Plasticised cloth Edgewound alum. ribbon Ferrite THIELE-SMALL PARAMETERS** Resonant Frequency, fs D.C. Voice Coil Resistance, Re Mechanical Quality Factor, Qms Electrical Quality Factor, Qes Total Quality Factor, Qts Equivalent Air Volume to Cms, Vas Mechanical Compliance, Cms Mechanical Resistance, Rms Efficiency, ho (%) Effective Surface Area, Sd(m2) Maximum Displacement, Xmax Displacement Volume, Vd Voice Coil Inductance, Le @ 1kHz 50 Hz 5.8 ohms. 7.93 0.223 0.22 64 l 316.6 µm/N 1.27 kg/s 3.35 0.038 m2 3.5 mm. 130 cm.3 1 mH NOTES *The power capacity corresponds to the RMS maximum value that can dissipate the loudspeaker when a sinus signal is applied for a period of at least two hours. Program power is defined as the transducer’s ability to handle normal music program material. ** T-S parameters are measured after an exercise period using a preconditioning power test, using a velocity-current laser transducer, and will reflect the long term parameters, once the loudspeaker has been working for a short period of time. NOTAS *La potencia admisible corresponde a la máxima potencia RMS que puede disipar el altavoz durante al menos dos horas, cuando se le aplica una señal senoidal determinada. Por potencia programa se entiende la capacidad del altavoz en el manejo de señales transitorias, como sería el proporcionado por el contenido de un pasaje musical normal. * *Los parámetros T-S han sido medidos después de un periodo de fatiga y estabilización de las suspensiones, mediante transductor laser de velocidad-corriente, y son el reflejo de los parámetros a largo plazo del altavoz, una vez éste haya sido instalado y haya trabajado en un corto espacio de tiempo. - 22 -