Yamaha EAD10 Drum Module Manual de usuario

Marca: Yamaha

Modelo: EAD10 Drum Module

Categoría: Tambores musicales

Tipo: Manual de usuario

Este manual también es adecuado para

Owner’s Manual

Electronic Acoustic

Drum Module

Quick Guide

Features of the EAD10

page 6

page 10

S-1

EAD10 Owner’s Manual

For EAD10

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or specifically

recommended by Yamaha.

WARNING: Do not place this product in a position where anyone

could walk on, trip over, or roll anything over power or connecting

cords of any kind. The use of an extension cord is not recommended!

If you must use an extension cord, the minimum wire size for a 25’

cord (or less ) is 18 AWG. NOTE: The smaller the AWG number, the

larger the current handling capacity. For longer extension cords, con-

sult a local electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at

the time of printing. However, Yamaha reserves the right to change or

modify any of the specifications without notice or obligation to update

existing units.

This product, either alone or in combination with an amplifier and

headphones or speaker/s, may be capable of producing sound levels

that could cause permanent hearing loss. DO NOT operate for long

periods of time at a high volume level or at a level that is uncomfort-

able. If you experience any hearing loss or ringing in the ears, you

should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory mount-

ing fixtures that are either supplied with the product or as optional

accessories. Some of these items are designed to be dealer assem-

bled or installed. Please make sure that benches are stable and any

optional fixtures (where applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are

not covered by the manufacturer’s warranty, and are therefore the

owners responsibility. Please study this manual carefully and consult

your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and envi-

ronmentally friendly. We sincerely believe that our products and the

production methods used to produce them, meet these goals. In keep-

ing with both the letter and the spirit of the law, we want you to be

aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of

battery is approximately five years. When replacement becomes nec-

essary, contact a qualified service representative to perform the

replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery

being charged.

When installing batteries, never mix old batteries with new ones, and

never mix different types of batteries. Batteries MUST be installed cor-

rectly. Mismatches or incorrect installation may result in overheating

and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all bat-

teries away from children. Dispose of used batteries promptly and as

regulated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some rea-

son its useful life is considered to be at an end, please observe all

local, state, and federal regulations that relate to the disposal of prod-

ucts that contain lead, batteries, plastics, etc. If your dealer is unable

to assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this manual

as a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

SPECIAL MESSAGE SECTION

92-BP (bottom)

COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Electronic Acoustic Drum Module

Model Name : EAD10

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (FCC DoC)

S-2

EAD10 Owner’s Manual

For AC adaptor and EAD10

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please contact

Yamaha Corporation of America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

S-3

EAD10 Owner’s Manual

For AC adaptor

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

(can_b_02)

CAN ICES-3 (B)/NMB-3(B)

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol within

an equilateral triangle is intended to alert the user

to the presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of suffi-

cient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral trian-

gle is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accor-

dance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manu-

facturer.

12 Use only with the cart, stand, tri-

pod, bracket, or table specified by

the manufacturer, or sold with the

apparatus. When a cart is used,

use caution when moving the cart/

apparatus combination to avoid

injury from tip-over.

13 Unplug this apparatus during light-

ning storms or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

S-4

EAD10 Owner’s Manual

(standby)

(weee_eu_en_02)

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den ar ansluten till vägguttaget, även om själva apparaten har stängts av.

ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt, sålænge netledningen sidder i en stikkontakt, som er tændt — også selvom der

er slukket på apparatets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta.

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and

electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection

points, in accordance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment which could otherwise arise from inappropriate

waste handling.

For more information about collection and recycling of old products, please contact your local municipality,

your waste disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further

information.

Information on Disposal in other Countries outside the European Union:

This symbol is only valid in the European Union. If you wish to discard these items, please contact your

local authorities or dealer and ask for the correct method of disposal.

EAD10 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

• This AC adaptor is designed for use with only Yamaha electronic instruments. Do

not use for any other purpose.

• Indoor use only. Do not use in any wet environments.

CAUTION

• When setting up, make sure that the AC outlet is easily accessible. If some trouble

or malfunction occurs, immediately turn off the power switch of the instrument and

disconnect the AC adaptor from the outlet. When the AC adaptor is connected to

the AC outlet, keep in mind that electricity is flowing at the minimum level, even if

the power switch is turned off. When you are not using the instrument for a long

time, make sure to unplug the power cord from the wall AC outlet.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting,

damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators. Also,

do not excessively bend or otherwise damage the cord, or place heavy objects on

it.

• Only use the voltage specified as correct for the instrument. The required voltage is

printed on the name plate of the instrument.

• Use the specified adaptor (page 63) only. Using the wrong adaptor can result in

damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the instrument or

attempt to disassemble or modify the internal components in any way. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected by

qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings. If any liquid such as water

seeps into the instrument, turn off the power immediately and unplug the power

cord from the AC outlet. Then have the instrument inspected by qualified Yamaha

service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may fall

over and cause a fire.

• When one of the following problems occur, immediately turn off the power switch

and disconnect the electric plug from the outlet. Then have the device inspected by

Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

For AC adaptor

For EAD10

Power supply/AC adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

DMI-5 1/2

EAD10 Owner’s Manual

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other

property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• When removing the electric plug from the instrument or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used for

extended periods of time, or during electrical storms.

• Read carefully the attached documentation explaining the assembly process.

Failure to assemble the instrument in the proper sequence might result in damage

to the instrument or even injury.

• Do not place the instrument in an unstable position where it might accidentally fall

over.

• Before moving the instrument, remove all connected cables, to prevent damage to

the cables or injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the power

switch and disconnect the plug from the outlet. Even when the power switch is

turned off, electricity is still flowing to the product at the minimum level. When you

are not using the product for a long time, make sure to unplug the power cord from

the wall AC outlet.

• Use the included module holder if you are installing the EAD10 on the hi-hat stand.

Also, make sure you use the wing bolts included with the module holder. Failure to

do so could cause damage to the internal components or result in the instrument

falling over.

• Be sure to securely tighten the clamp screw and module holder wing bolts when

setting up the EAD10. Also, do not loosen the clamp screw or module holder wing

bolts rapidly. Not doing so can cause parts to fall off the main unit, sensor unit, or

module holder resulting in injury.

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels and gradually

raise the volume controls while playing the instrument to set the desired listening

level.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a high

or uncomfortable volume level, since this can cause permanent hearing loss. If you

experience any hearing loss or ringing in the ears, consult a physician.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

Power supply/AC adaptor

Assembly

Location

Connections

Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

DMI-5 2/2

EAD10 Owner’s Manual

NOTICE

To avoid the possibility of malfunction/ damage to the product, damage

to data, or damage to other property, follow the notices below.

 Handling

• Do not use the instrument in the vicinity of a TV, radio, stereo equip-

ment, mobile phone, or other electric devices. Otherwise, the

instrument, TV, or radio may generate noise. When you use the

instrument along with an application on your iPad, iPhone or iPod

touch, we recommend that you set “Airplane Mode” to “ON” on that

device in order to avoid noise caused by communication.

• Do not expose the instrument to excessive dust or vibrations, or

extreme cold or heat (such as in direct sunlight, near a heater, or in

a car during the day) to prevent the possibility of panel disfiguration,

damage to the internal components or unstable operation.

• Do not place vinyl, plastic or rubber objects on the instrument,

since this might discolor the panel or keyboard.

 Maintenance

• When cleaning the instrument, use a soft and dry/slightly damp

cloth. Do not use paint thinners, solvents, alcohol, cleaning fluids,

or chemical-impregnated wiping cloths.

 Saving data

• System settings (Reference Manual (Advanced)(PDF)) are stored

automatically and will not be lost when the power is turned off.

However, settings may be lost due to malfunction or improper oper-

ation. Save important data to an external device such as a USB

flash drive or a computer (pages 25 and 30). Please read page 30

before using a USB flash drive.

• Edits to Scenes, etc., are lost if not saved before the power is

turned off. Likewise, edits are lost when the auto power off function

turns the power off (page 29). Save data you want to keep to the

main unit, or to an external device such as a computer or USB flash

drive (pages 25 and 30). However, data stored in the main unit may

be lost due to malfunction or improper operation. Save important

data to an external device such as a USB flash drive or a computer

(pages 25 and 30). Please read page 30 before using a USB flash

drive.

• To protect against data loss through USB flash drive damage, we

recommend that you save your important data onto spare USB

flash drive or an external device such as a computer as backup

data.

Information

 About copyrights

• Copying of the commercially available musical data including but

not limited to MIDI data and/or audio data is strictly prohibited

except for your personal use.

• This product incorporates and bundles contents in which Yamaha

owns copyrights or with respect to which Yamaha has license to use

others’ copyrights. Due to copyright laws and other relevant laws,

you are NOT allowed to distribute media in which these contents

are saved or recorded and remain virtually the same or very similar

to those in the product.

* The contents described above include a computer program, Accompani-

ment Style data, MIDI data, WAV data, voice recording data, a score, score

data, etc.

* You are allowed to distribute medium in which your performance or music

production using these contents is recorded, and the permission of Yamaha

Corporation is not required in such cases.

 About this manual

• The illustrations and LCD screens as shown in this manual are for

instructional purposes only, and may appear somewhat different

from those on your instrument.

• Windows is a registered trademark of Microsoft® Corporation in the

United States and other countries.

• MacOS, iPhone and iPad are trademarks of Apple Inc., registered

in the U.S. and other countries.

• The company names and product names in this manual are the

trademarks or registered trademarks of their respective companies.

• The names of buttons, terminals, and the like from the EAD10’s

front, rear and top panels are enclosed in [ ] (square brackets).

 Latest Firmware Version

From time to time, Yamaha may update product firmware without

prior notice.

We recommend, therefore, that you check our web site (below) for

the latest version and keep your EAD10 firmware up to date.

http://download.yamaha.com/

The content of this Owner’s Manual applies to the newest version of

the firmware as of printing. Details regarding any functions added to

later versions will also be made available via the above web site.

 About the Pads

Within this Owner’s Manual, the optional external pads that may be

connected to the EAD10 are referred to by model name. Please note

that these model names were up-to-date as of printing of this man-

ual.

Details regarding any subsequently released models will be made

available via the following web site.

http://download.yamaha.com/

* Yamaha Corporation reserves the right to modify this URL at any

time without prior notice.

EAD10 Owner’s Manual

(bottom_en_01)

The model number, serial number, power requirements, etc., may be found on or near the

name plate, which is at the bottom of the unit.

You should note this serial number in the space provided below and retain this manual as a

permanent record of your purchase to aid identification in the event of theft.

Model No.

Serial No.

EAD10 Owner’s Manual

Quick Guide

Adjusting Volume and Sound Balance (page 13)

Turn the [MASTER VOLUME] knob or [AUDIO/

CLICK VOLUME] knob.

Hit all drums and cymbals in the drum set to make sure

that the EAD10 is picking up the sound.

Changing Sounds (page 33)

Turn the [SCENE] knob to select different

sounds (Scenes).

Adjust the levels with the [REVERB],

[EFFECT], and [TRIGGER] knobs.

Practicing with the Metronome (Click) (page 39)

Press the [ ] (Click) button.

Press the button below “ ” to the start the

Metronome.

Use the [+] or [–] buttons to adjust the tempo.

Press the “ ” button again to stop the Metro-

nome.

Overall volume Volume control for the AUX

IN (auxiliary input) and Met-

ronome (click)—sounds

other than what you play

Adjusts the

Reverb depth

Adjusts the Trigger Sound

volume (with the default

setting, the Trigger sound is

added to the bass drum)

Adjusts the

Effect depth

132, 4

EAD10 Owner’s Manual

Quick Guide

Playing Along with a Favorite Song (page 24)

Connect a portable music player to the [AUX

IN] jack.

Start music playback on your portable

player.

Play the drums while listening with head-

phones.

Recording Your Performance (page 41)

Press the [RECORDER] button.

Press the button below “” to start record-

ing.

Play the drums.

Press the button below “ ” to stop record-

ing.

12, 4

EAD10 Owner’s Manual

PRECAUTIONS 2

Quick Guide 6

Included Accessories 9

Features of the EAD10 10

How the EAD10 makes sound........................................... 11

About the Manuals 12

Printed Manual .................................................................. 12

Digital Manual (PDF) ......................................................... 12

Panel Controls and Functions 13

Main Unit ........................................................................... 13

Sensor Unit........................................................................ 15

About the Trigger Input Jacks............................................ 16

Setup Guide 17

Setting Up.......................................................................... 17

Connect with Other Devices and Expand the Fun............. 24

Turning On or Off............................................................... 25

Setting Up the Sensor Unit ................................................ 27

Changing the Overall Settings........................................... 29

Using a USB Flash Drive................................................... 30

Basic Guide 32

Performing with Various of Scenes ................................... 32

Creating Your Own Scene................................................. 35

Using the Click (Metronome) ............................................. 39

Recording Your Performance............................................ 41

Application Guide 48

Enhance Your Drum Set with Separately Sold Add-Ons... 48

Reference 55

Menu List........................................................................... 55

Troubleshooting................................................................. 58

Message List ..................................................................... 61

Specifications .................................................................... 63

Index.................................................................................. 64

Contents

EAD10 Owner’s Manual

Welcome

Thank you for purchasing this Yamaha product.

To get the most out of your EAD10, be sure to read this Owner’s Manual carefully.

And after reading through this manual, be sure to store it in a safe place

so that you can refer back to it again as needed.

Included Accessories

Owner’s Manual (this book)

AC adaptor

Module holder

Module holder wing bolts (× 2)

Connector cables (1 pair)

Cable bands (× 3)

Adhesive cushions (× 2)

EAD10 Owner’s Manual

Features of the EAD10

The EAD10 lets you easily change the sound of your acoustic drums into the sound of your liking.

Connect a smart phone to the EAD10 and enjoy playing the drums along with your favorite music.

Also, it can be used in a wide range of applications from practice, recording to live situations.

• Sensor Unit that mounts on the bass drum makes setup simple

• Built-in XY configured stereo mic provides high quality monitoring of the entire drum set with natu-

ral balance and stereo orientation

• Loud drums can be monitored with proper volume using headphones or earphones

• Change effect settings with a single knob and easily save and recall settings

• PCM tone generator makes it easy to change the sound of your bass drum by using a Triggered

sound — even in the middle of a performance

• Play a wide range of musical genres from contemporary to the by using the effects, your own sam-

ples or the internal Triggered sounds

• Recording and playback possible via USB flash drive or USB audio

• Left and right outputs allow you to easily connect to a PA

Main Unit Sensor Unit

Easy setup allows comfortable monitoring of your drum sound while playing

Transforms the sound of your drums into a sound of your liking

Use for recording or in-live situations

EAD10 Owner’s Manual

 How the EAD10 makes sound

The Sensor Unit sends two types of signals to the Main Unit; an audio signal captured with the mic

sensor, and a trigger signal captured with the trigger sensor.

The audio signal can be processed with Effects, while the trigger sensor can be used to play Trigger

Sounds depending on how you play your drums.

For more information on Trigger Sounds, Effects, and Reverb, please see “What is a Scene?” (page

32).

Mic sensor

Trigger sensor

Audio signal from

the drum set

Trigger signal from

the bass drum

(Mic sound &)

Effects

Trigger Sound

(internal Voices)

Reverb

Sensor Unit

Main Unit

EAD10 Owner’s Manual

About the Manuals

The following manuals are provided for using the EAD10. These manuals are intended for users

of the EAD10.

Owner’s Manual (this book)

Setup Guide

Explains how to attach and setup the EAD10 for producing sound.

Basic Guide

Describes the fundamentals needed to operate the EAD10.

Application Guide

Describes parameter settings and other more advanced uses.

Reference

Describes troubleshooting techniques and contains other reference materials.

Reference Manual (Advanced)

The Reference Manual provides a description of all of the functions that can be accessed by pressing the [MENU] but-

ton.

Data List

This provides lists of Scene and Effect names in the EAD10, and MIDI related information.

iPhone/iPad Connection Manual

Describes how to connect smart devices such as an iPhone and iPad.

Printed Manual

Digital Manual (PDF)

The digital format manuals listed above can be obtained from the Yamaha Downloads web page.

To do so, go to the web page using the following URL, enter “EAD10” in the “Model Name”

field, and then click “Search.”

Yamaha Downloads: http://download.yamaha.com/

EAD10 Owner’s Manual

Panel Controls and Functions

Main Unit

Top Panel

[AUDIO/CLICK VOLUME] knob

Adjusts the volume for AUX IN (aux-

iliary input) and Click functions—any

sound or audio you play along to.

Function Buttons 1–3

(page 33) ([F1], [F2], [F3])

Selects the functions that

appear at the bottom of each

screen.

Display (page 33)

Displays a variety of informa-

tion.

[SCENE] knob (page 33)

Switches between the dif-

ferent sound sets.

Or, returns to the Scene

screen from other screens.

NOTE

The knob can be used in the same manner as the

[–] and [+] buttons. For more information, refer to the

Reference Manual (Advanced) (PDF) (MENU/Utility/

General).

[ ] (Standby/On) switch (page 25)

Switches the power between standby (off) and

on.

[MENU] button

Accesses the advanced settings

screen. For more detailed informa-

tion, refer to the Reference Manual

(Advanced) (PDF).

[REVERB] knob (page 33)

Adjusts the reverb level.

[EFFECT] knob (page 33)

Adjusts the amount of Effect applied to the

audio signal from the mic sensor.

[TRIGGER] knob (page 33)

Adjusts the Trigger Sound volume.

[STORE] button (page 37)

Opens the Store screen. Stores Scenes

that you have created.

[–] button,

[+] button

Increases or

decreases the

value by one (1).

[ ] (Click) button (page 39)

Accesses the Click (Metronome)

screen. The button flashes in

sync with the Click tempo.

[RECORDER] button (page 41)

Accesses the Recorder (record/play-

back) screen. The button lights while

recording or during playback.

[EXIT] button

Cancels the action, or returns to the screen one level higher.

Press several times to return to the Scene screen.

NOTE

When in the Scene Screen, this button can also be used as a

Panic Button to stop any sounds.

[ ] (Sensor Unit) button

(page 27)

Accesses the Sensor Unit

screen. Set the mic sensor level

so that the button occasionally

flashes when hitting the drums

strongly.

[MASTER VOLUME] knob

Adjusts the overall volume.

EAD10 Owner’s Manual

Panel Controls and Functions

Rear Panel

[FOOT SW] Jack (page 48)

Connects a foot pedal or foot switch (sold sep-

arately).

FC5 HH65

etc.

FC7

TO SENSOR UNIT [A] jack

(page 17)

Connect to the [A] jack on the

Sensor Unit using the connec-

tor cable (included).

TO SENSOR UNIT [B] jack

Connect to the [B] jack on the

Sensor Unit.

For more information on the [qKICK/w]

to [y] jacks, see “About the Trigger Input

Jacks” (page 16).

Sensor Unit

Standard phone plug

(6.3 mm)

Stereo mini plug

(3.5 mm)

DC IN jack (page 17)

Use the AC adaptor that

came with the EAD10.

USB cable

[USB TO DEVICE] termi-

nal (page 30)

Connects a USB flash

drive.

Cannot be used with other

USB devices.

[USB TO HOST] terminal (page 25)

Connect a computer or smart device

such as an iPhone or iPad to send and

receive digital signals (audio and MIDI).

Additional parts are required for connect-

ing an iPhone or iPad. For more informa-

tion, refer to “iPhone/iPad Connection

Manual” (PDF).

Cord hook (page 17)

Wrap the AC adaptor cord

around this hook to prevent

accidental unplugging dur-

ing use.

Cord hook

AC adaptor cord

[AUX IN] (auxiliary

input) jack

(page 17)

Connect to the

headphone jack on

a smart phone or

portable music

player.

OUTPUT [R]/[L/MONO]

jacks (page 17)

Connect to powered speak-

ers or other such PA system.

These jacks are standard

phone type output jacks.

If mono output is required,

use only the [L/MONO] jack.

EAD10 Owner’s Manual

Panel Controls and Functions

Front Panel

Sensor Unit

NOTICE

Do not hit the Sensor Unit with the drumsticks. Doing so can damage the mic sensor resulting in inferior performance.

Standard stereo phone plug

(6.3 mm)

[PHONES] jack

Connects headphones. This output jack is a standard

stereo phone plug (6.3 mm). Use a 3.5 mm stereo

mini to (6.3 mm) stereo adaptor to connect head-

phones or earphones with a stereo mini plug (3.5 mm)

to the [PHONES] jack.

CAUTION

Do not use headphones for a long period of time at

high volume. Doing so can cause loss of hearing.

Mic Sensor

Captures the whole drum set’s

acoustic sound converting it into

an audio signal.

[A] jack

Connect to the TO SENSOR UNIT

[A] jack on the rear panel using

the connector cable (included).

Sends the trigger sensor signal.

[B] jack

Connect to the TO SENSOR UNIT

[B] jack on the rear panel using

the connector cable (included).

Sends the mic sensor signal.

Clamp screw (page 17)

Secures the Sensor Unit to

the bass drum hoop.

Trigger sensor

Converts vibrations produced

when the bass drum is hit

into a trigger signal.

EAD10 Owner’s Manual

Panel Controls and Functions

Trigger signals are received via the trigger input jacks. These are used for connecting separately sold accessories to the

EAD10. You can connect up to six pads or drum triggers.

[qKICK/w] through [y] jacks are located on the rear panel of the Main Unit.

Visit the web page below for more information on separately sold accessories that can be connected to each trigger input

jack.

For more information on connections of separately sold accessories, see “Enhance Your Drum Set with Separately Sold

Add-Ons” (page 48).

Yamaha Downloads: http://download.yamaha.com/

* Yamaha Corporation reserves the right to modify this URL at any time without prior notice.

About the Trigger Input Jacks

Standard stereo phone plug

(6.3 mm)

Trigger Input jacks

[qKICK/w]

The TO SENSOR UNIT [A] jack can

be as the [qKICK/w] jack (page 48).

This jack consists of a pair of mono

trigger inputs.

[eSNARE/r]

This jack consists of a pair of mono

trigger inputs. Connects drum triggers

such as the DT50S (sold separately)

(page 48).

DT50S

[t] and [y]

Connects DTX Series pads, etc.

(page 48).

Supports three-zone pads.

TP70S

XP80

PCY135

Using a commercially available Y-cable you

can connect two mono pads.

For example, you can connect a Sensor Unit

and a kick pad to the [qKICK/w] jack.

Stereo audio plug

Mono phone jack

 Y-cable

KU100

EAD10 Owner’s Manual

Setup Guide

This provides information on setup and initial settings in preparation for playing.

This completes set up.

 Positioning the drum set

The bass drum should be the central point in the drum set, with the snare, toms, cymbals, positioned in a well balanced man-

ner around it. Instruments positioned away from the Sensor Unit mounted on the bass drum may sound lower in volume.

When instruments such as the ride cymbal are positioned too close to the Sensor Unit, the sound will be too loud and out of

balance.

Using the sensor with double bass drum set ups gives an uneven and unbalanced sound, so we do not recommend using it in

this situation.

Workflow

Attaching the Sensor Unit

Installing the Main Unit

Connecting the Cables

Taking Measures Against Noise

Connecting the AC adaptor

Setting Up the Sensor Unit

Setting Up

EAD10 Owner’s Manual

Setting Up

Setup Guide

 Attaching the Sensor Unit

Attach the Sensor Unit to the top of the batter side bass drum hoop.

 Standard Straight Hoop

Slide the Sensor Unit onto the top of the batter side bass drum hoop as far as possible.

Lift the Sensor Unit and after making sure both surfaces shown in the figure below are in

contact with the hoop, turn the clamp screw.

Tighten the clamp screw firmly, making sure that the Sensor Unit is secure and not loose.

 Other Hoop Types

Attach the included adhesive cushions,

one each to the top of the inner and

outer hoop surfaces.

Attach the sensor using the same procedure as for a standard hoop drum.

NOTICE

Make sure the uneven surface is filled with adhe-

sive cushions to provide a secure attachment for

the sensor. The Sensor Unit may fall off if the

adhesive cushions is not used.

Wood hoops

Side view

Top of the

batter side

Hoop

Make sure these two

surfaces are in con-

tact with the hoop

Make sure this sur-

face is in contact

with the hoop

Clamp

screw

Adhesive

cushion

(cross section)

Uneven profile type

Metal hoops

(cross section)

EAD10 Owner’s Manual

Setting Up

Setup Guide

 Installing the Main Unit

Either place the Main Unit on a table, or attach the Main Unit to a hi-hat stand.

 Placing on a Flat Surface

Place the Main Unit on a table or flat surface.

 Mounting on a Hi-Hat Stand

Combine the included module holder with a separately sold cymbal stand attachment

(CSAT924A) and mount on the hi-hat stand.

Tighten the module holder wing nuts to securely fasten the Main Unit and module holder.

We recommend attaching the Main Unit to a position where it cannot be hit by your knees.

Cymbal Stand

Attachment

Exploded view

Main Unit

Module holder

Module holder wing

bolts

Cymbal Stand

Attachment

EAD10 Owner’s Manual

Setting Up

Setup Guide

We recommend positioning the Main Unit so

that it is inside the outer edge of the cymbal

when viewed from above to avoid hitting the

Main Unit.

Use a drum key (sold separately) on the Main Unit angle

adjustment.

 Connecting the Cables

Connect the straight plug to the Main Unit, and the L-shaped

plug to the Sensor Unit.

Included Connector Cables

[A] jack on the rear panel of the Main Unit

[A] jack on the Sensor Unit

[B] jack on the Main Unit

[B] jack on the Sensor Unit

CAUTION

Do not connect or disconnect cables while the power is

ON.

About the Module Holder

The module holder has three sets of holes. Use the center set of holes to mount in a standard position. Use the

rear set of holes if you want the unit positioned forward, and use the front set of holes to position the unit to the

rear.

Main Unit

Front panel side

Rear panel side

Module holder

Main Unit

Angle adjustment key bolt

Module holder

Rear position

Standard position

Forward position

NOTE

The module holder is 22.2 mm (7/8") diameter.

Cymbal

Snare drum

(EAD10)

Main Unit

Sensor Unit

EAD10 Owner’s Manual

Setting Up

Setup Guide

 Taking Measures Against Noise

To eliminate the cause of the noise, adjust positions beforehand so that your toms do not touch the Sensor Unit or that the

Connector Cables do not move around the Sensor Unit during your performance.

 Check the Sensor Unit Location

Make sure the Sensor Unit does not touch the toms or other

instruments.

 Securing the Cables

Position the L-shaped plugs connected the Sensor Unit on their

sides. This provides a more stable cable position.

Use the Cable band to secure the Connector Cables close to the

Sensor Unit.

When mounting the Main Unit on a hi-hat stand, use the Cable

band to keep the cables from interfering with the foot pedal.

Example of poor placement

Viewed from above

Viewed from the

Sensor Unit jack side

Hoop

Viewed from above

Cable band

EAD10 Owner’s Manual

Setting Up

Setup Guide

 Connecting the AC adaptor

Make sure that the power is turned off (all

panel lights and the screen backlight are

off).

For removable plug type AC adaptors only:

Make sure that the plug is not disconnected.

Connect the AC adaptor.

WARNING

Only use the specified AC adaptor (page 63). Using a different AC adaptor can cause malfunction, overheating, fire, and

other problems. This may void the warranty so please take careful note.

CAUTION

Locate the Main Unit close to an AC outlet. If you notice any abnormalities during operation, turn the power off immedi-

ately and unplug the AC adaptor.

WARNING

• For AC adaptors with a removable plug, only use the

AC adaptor with the plug attached, and keep the

plug. Plugging only the plug into the power outlet

can cause electric shock or fire.

• If the removable plug comes off from the AC adaptor,

avoid touching the metal parts on the plug and slide

the AC adaptor onto the plug until you hear it lock on

to the adaptor with a click. Also, make sure you keep

any foreign objects out of the plug. This can cause

electrical shock, short circuit, or failure.

WARNING

Make sure to use the specified AC Adaptor.

No screen backlight

All off

Slide in the direction

indicated with the arrow.

Plug

DC IN jack

(page 63)

EAD10 Owner’s Manual

Setting Up

Setup Guide

Hook the AC adaptor’s cord around the cord

hook to secure it in place.

Plug the AC adaptor’s AC plug into a domes-

tic power outlet.

 Connecting Headphones

Connect the headphones to the [PHONES] jack.

CAUTION

Excessive bending can damage the AC adaptor cord

and create a fire hazard. Ensure, therefore, that the

power cord is not bent at an extreme angle when

wrapped around the hook.

CAUTION

Even when the [ ] (Standby/On) switch is in standby

status (power lamp is off/display is off), electricity is

still flowing to the instrument at the minimum level.

When you are not using the EAD10 for a long period of

time, make sure that you unplug the AC adaptor from

the wall AC outlet.

NOTE

When disconnecting the AC adaptor, turn the instrument and then carry out this procedure in reverse order.

CAUTION

Do not use headphones at high volume for an extended

period of time. Doing so can cause loss of hearing.

NOTE

Please take note of the following if you are using open or semi-

open headphones.

- Volume tends to sound louder because of the sound of the

drums leaking into the headphones when playing.

- When recording or connected to a PA, the Click sound from

the headphones may get mixed into your recording or PA

system.

Cord hook

AC adaptor cord

Power outlet

AC adaptor

Front panel side

EAD10 Owner’s Manual

Connect with Other Devices and Expand the Fun

Setup Guide

This section describes how to connect to a portable music player and PA system.

 Connecting a Portable Music Player

You can play along with audio playback from a smartphone or

portable music player.

Connect the smartphone or portable music player to the [AUX

IN] jack.

 Connecting to a PA System

Connect the OUTPUT [R]/[L/MONO] jacks to the PA system.

Connect with Other Devices and Expand the Fun

NOTICE

Before making any connections, make sure volume levels on

all devices are set at their minimum.

CAUTION

• Acoustic feedback (a loud squeal or screech) may occur

depending upon the position of the microphone and the

proximity and direction of the speakers.

• Please note that Scenes using high-gain effects such as

distortion or compression are more likely to cause feed-

back if the speakers are too close or pointed towards the

drum set.

NOTICE

• Whenever connecting other devices, make sure that plugs

on the cables you are using match the jacks on each

device.

• Make sure the volume levels on all external devices are set

at their minimum.

• When using the Main Unit with an external device for

sound output, turn the Main Unit power on first, and then

the power on the external device. When turning power off,

do so in the reverse order. Not following the proper order

can damage the equipment.

Stereo mini plug

(3.5 mm)

Standard phone plug

(6.3 mm)

EAD10 Owner’s Manual

Turning On or Off

Setup Guide

 Connecting a Computer

If you have a computer and DAW software, connect the Main Unit to the computer and you can record your performance

and listen to the playback from the computer. For more information, refer to the Reference Manual (Advanced) (PDF).

 Turning On

Turn the [MASTER VOLUME] knob fully

counterclockwise to lower the Main Unit vol-

ume to its minimum.

Press the [ ] (Standby/On) switch.

The startup screen appears in the LCD.

Turning On or Off

CAUTION

Do not reconnect cables between the Main Unit and Sensor Unit after turning the power on. Doing so will cause noise.

Precautions when using the [USB TO HOST] terminal

When connecting the computer to the [USB TO HOST] terminal, make sure to observe the following points. Failing

to do so risks freezing the computer and corrupting or losing the data.

If the computer or the instrument freezes, restart the application software or the computer OS, or turn the power to

the EAD10 off then on again.

NOTICE

• Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used.

• Before connecting a computer to the [USB TO HOST] terminal, disable any power-saving mode of the computer

(such as suspend, sleep, or standby).

• Execute the following before turning the power to the instrument on/off or plugging/unplugging the USB cable to/

from the [USB TO HOST] terminal.

- Quit any open application software on the computer.

• While the computer is connected to the EAD10, you should wait for six seconds or more between these opera-

tions: (1) when turning the power of the EAD10 off then on again, or (2) when alternately connecting/disconnect-

ing the USB cable.

May differ from the actual specifica-

tions.

EAD10 Owner’s Manual

Turning On or Off

Setup Guide

If you are connected to a PA system:

Turn the external speakers on.

 Turning Off

If you are connected to a PA system:

Turn the external speakers off.

Turn the [MASTER VOLUME] knob fully

counterclockwise to lower the volume to its

minimum.

Hold down the [ ] (Standby/On) switch.

The EAD10 is in Standby and the display and lights are

off.

NOTICE

• The Main Unit automatically stores settings when the power is turned off, so do not unplug the AC adaptor until the LCD

screen is turned off completely.

• Unsaved Scene data will lost, so always save (Store) data before turning the power off.

Power on

Power off

Hold down

All off

EAD10 Owner’s Manual

Setting Up the Sensor Unit

Setup Guide

 About the Sensor Unit Settings

Adjust the gain and sensitivity settings for the Mic sensor and Trigger sensor built into the Sensor Unit. When you need to

adjust the gain, you can also use the Auto Setting feature.

 Setting the Sensor Gain Automatically

Press the [ ] (Sensor Unit) button.

The SENSOR UNIT screen appears.

Setting Up the Sensor Unit

Setting Screen display Optimal condition

MIC

(Mic gain)

The level should occasionally reach to the right and the [ ]

(Sensor Unit) button lights by striking all the instruments in

the drum set.

TRG

(Trigger gain)

The level should reach to the right when the bass drum is

struck loudly

Mic gain

Trigger gain

Press the [EXIT] but-

ton to return to the

Scene screen.

Setting Up Automatically

Press the button below “AUTO” ([F3]).

Strike each of the instruments in the drum set with

an 8-beat rhythm.

The setting is complete after about 10 seconds of playing the drums.

If you want to stop the Auto Setting before completion, press “STOP.”

NOTE

Detection may fail in some cases, particularly if there is background noise. When detection fails, try the Auto Setting several

times. Fine adjustments should be done manually. If the Auto setting is not successful after several attempts, adjust manually.

The setting is complete when

“AUTO” reappears.

EAD10 Owner’s Manual

Setting Up the Sensor Unit

Setup Guide

 Manually Adjusting the Sensor Unit Settings

Press the [ ] (Sensor Unit) button.

The SENSOR UNIT screen appears.

Use the buttons below “ ” or “ ” ([F1] or

[F2]) to move the cursor.

Use the [–] or [+] buttons to adjust the value.

 Setting Finer Adjustments

With the SENSOR UNIT screen displayed, press the button

below “ ” ([F2]).

The SENSOR UNIT (fine adjustment) screen opens.

Press the [EXIT] button to

return to the Scene screen.

TRG SENS

(Trigger Sensitivity)

Sensitivity for

light strokes

The larger the value, the louder

the sound produced when struck

lightly.

[L] Mic gain left Adjust the L and R settings when

the volume balance between the

left and right Mics is poor.

[R] Mic gain right

Mic gain

Trigger gain

Lower Higher

SENSOR UNIT screen

SENSOR UNIT (fine adjustment) screen

NOTE

• If this is set too low, the Trigger

sound might not be played.

• If this is set too high, the snare

drum or toms might trigger the

bass drum Trigger Sound when

hit.

NOTE

The same value is displayed in the

[L] setting in the SENSOR UNIT

(fine adjustment) screen and in the

“MIC” setting in the SENSOR UNIT

screen.

EAD10 Owner’s Manual

Changing the Overall Settings

Setup Guide

Use the buttons below “ ” or “ ” ([F1] or

[F2]) to move the cursor.

Use the [–] or [+] buttons to adjust the value.

 Auto Power-Off

The Auto Power-Off function automatically turns off the Main Unit after a certain period of inactivity. The factory default is

set at 30 minutes.

 Auto Power-Off Quick Cancel

While holding down the [STORE] button, press the [ ]

(Standby/On) button to cancel the Auto Power-off. The func-

tion will remain off until you set a new Auto Power-Off time.

Changing the Overall Settings

NOTICE

• Unsaved data is lost when the Main Unit is turned off with the Auto Power-Off function. Always store data before turning

the power off.

• In certain modes of operation, the Auto Power-Off function will not turn off the Main Unit when the set time has elapsed.

So we recommend that you always turn off the Main Unit manually when you are finished using it.

• If you expect the Main Unit to be inactive for a certain length of time while connected to external audio equipment or a

PA, we recommend fully lowering the volume on the external equipment. Alternatively, you can disable the Auto Power-

Off function to ensure that the Main Unit stays on.

NOTE

To set the Auto Power-Off to a time other than 30 minutes, access the setting from the [MENU] button. (MENU/Utility/General)

Lower Higher

EAD10 Owner’s Manual

Using a USB Flash Drive

Setup Guide

 Restoring Main Unit Settings to the Factory Defaults (Factory

Reset)

Use the Factory Reset function to restore the Main Unit’s settings to their factory defaults, even if you have accidentally

overwritten them.

 Performing a Factory Reset

While holding down the [–] and [+] buttons, press the [ ]

(Standby/On) button to perform the factory reset.

Connect a USB flash drive to the [USB TO DEVICE] terminal on the rear panel of the Main Unit and record your perfor-

mance directly to the USB flash drive. Also, you can save Main Unit settings to and load settings from a USB flash drive.

 Connecting a USB Flash Drive to the Main Unit

Precautions When Using the [USB TO DEVICE] Terminal

When connecting a USB device to the terminal, be sure to follow the important precautions below.

NOTICE

A factory reset overwrites any settings you have made with the corresponding factory defaults. Save any important user-

defined data to a USB flash drive before carrying out a factory reset. For more information, refer to the Reference Manual

(Advanced) (PDF). (MENU/File)

NOTE

You can also access the factory reset with the [MENU] button.

Using a USB Flash Drive

NOTE

For more information about the handling of USB flash drives, refer to the owner’s manual of your USB flash drive.

EAD10 Owner’s Manual

Using a USB Flash Drive

Setup Guide

 Compatible USB Devices

USB flash drives only

Please check the URL shown below for a list of compatible USB flash drives.

http://download.yamaha.com/

 Connecting a USB Flash Drive

When connecting a USB device to the [USB TO DEVICE] terminal, make sure that the connector on the EAD10 is appro-

priate and that it is connected in the proper direction. The EAD10 conforms to the USB 1.1 specification. USB 2.0 and USB

3.0 flash drives can also be used. However, the transfer speed is equivalent to the USB1.1 specification.

 Formatting the USB Flash Drive

Some USB flash drives should be formatted with this instrument before they can be used. For information on how to format

the USB flash drive, refer to the Reference Manual (Advanced) (PDF). (MENU/File/Format)

 To Protect Your Data (Write Protection)

To prevent important data from being inadvertently erased, write-protect the USB flash drive. When you are saving data to

the USB flash drive, make sure you disable the write-protect first.

NOTE

• Other USB devices such as USB hub, mouse, computer keyboard, cannot be used.

• A USB cable cannot be used to connect a USB device to the [USB TO DEVICE] terminal.

NOTICE

The rating of the [USB TO DEVICE] terminal is a maximum of 5 V / 500 mA. Do not connect USB devices having a rating

above this, since this can cause damage to the instrument itself.

NOTICE

• Avoid connecting or disconnecting the USB device during playback/recording and file management operations (such as

Save, Copy, Delete, and Format), or when accessing the USB device. Failure to observe this may result in “freezing” of

the operation of the instrument or corruption of the USB device and the data.

• When connecting then disconnecting the USB device (and vice versa), make sure to wait a few seconds between the

two operations.

NOTICE

The format operation erases any previously existing data. Make sure that the USB flash drive you are formatting does not

contain any important data.

EAD10 Owner’s Manual

Basic Guide

 What is a Scene?

A Scene consists of a group of assigned settings for Reverb, Effects, and Trigger Sounds. The Main Unit includes preset

Scenes you can select to change the overall sound.

Also, you can save Scene settings as User Scenes, and recall User Scenes by turning the [SCENE] knob. (page 35)

For live use, you can sort and save Scenes in any order then recall Scenes by turning the [SCENE] knob or hitting a pad. For

more information, refer to the Reference Manual (Advanced) (PDF). (MENU/Job/Scene, MENU/Utility/PadFunction)

Performing with Various of Scenes

DISTORTION

DELAY

WAH

COMPRESSOR

FLANGER

PHASER

Scene

Reverb Trigger SoundEffects

Studio

Concert Hall

Stage

Distortion

Phaser

Wah

Delay

Flanger

Compressor

Bass drum

Cymbal

Cowbell

Snare drum

Other

instruments

Tambourine

Simulates the acoustical

characteristics of a

venue or studio. For

example, you can re-

create the ambiance of

a live venue in the com-

fort of your own home.

Sound captured with the Mic Sensor is

processed with delay, distortion, or

other sound varying Effects.

Use the Trigger Sound to emphasize or

enhance the sound of your drums.

Add some DTX Series pads and play

other sounds such as electronic drums.

EAD10 Owner’s Manual

Performing with Various of Scenes

Basic Guide

 Basic Scene Operation

 How to Read the Scene Screen

NOTICE

About the “ ” mark:

The mark appears in the upper left of the screen when a Scene’s settings

have been changed. This is to remind you that Scene settings have changed

but have not yet been saved (Store). The mark disappears when you store

the settings (page 37). When you select another Scene without first storing

the settings, the changes will be lost.

Switches the Scene type.

Returns you to the Scene Screen

from other screens.

Adjusts the volume of

Reverb, Effect, or Trigger Sound

Changes the type of

Reverb, Effect, or Trigger Sound

NOTE

When in the screens listed below, the knob can be used like the [–] and [+] but-

tons without returning to the Scene Screen.

• Screens such as Store where it is used for selecting a Scene Number

• Screen for entering a name

Scene number

Scene name

Opens to the

REVERB TYPE

settings screen

Opens to the

EFFECT TYPE

settings screen

Opens to the

TRIGGER INST

screen

If the Scene is synced to the tempo, the

tempo setting appears.

Displays the Sensor Unit status.

M: Mic volume

T: Trigger signal strength

Press the [EXIT] but-

ton to return to the

Scene screen from

each settings screen.

EAD10 Owner’s Manual

Performing with Various of Scenes

Basic Guide

 Selecting a Scene

Rotate the [SCENE] knob.

 Adjusting Scenes

 Adjusting Reverb and Effect Levels and Trigger Sound Volume

After editing a Scene, your edits will be lost if you select another Scene before saving (Storing) the edits.

Scene number

Scene name

Scene number and Scene name are

displayed on the screen.

P***: Preset Scene (Presets that are already

stored in the EAD10)

U***: User Scene (Scene you have created)

NOTE

When you select another Scene before storing

the Scene being edited, you can use the recall

function to recall the edited contents. For more

information, refer to the Reference Manual

(Advanced) (PDF) (MENU/Job/Scene/Recall).

[REVERB] knob

Adjusts the amount of

Reverb

[EFFECT] knob

Adjusts the amount of

Effect applied to the

sound of the acoustic

drum set

[TRIGGER] knob

Volume control for the

Trigger Sound assigned

to each trigger input

(Trigger signal level)

Maximum: all lit

Minimum: all off

EAD10 Owner’s Manual

Creating Your Own Scene

Basic Guide

You can customize preset Scenes to create your own Scene.

Creating Your Own Scene

Changing

the Reverb Type

Press the button

below “REV” ([F1]).

The REVERB TYPE screen

opens.

Use the [–] or [+] but-

tons to select the

Reverb type you want

to use.

Changing

the Effect Type

Press the button

below “EFF” ([F2]).

The EFFECT TYPE screen

opens.

Use the [–] or [+] but-

tons to select the

Effect type you want

to use.

Use the “ ” ([F1]) and

“ ” ([F2]) buttons to change

the tempo for tempo synced

Effects.

Changing

the Trigger Sound

 Changing the Trigger

Sound on the Bass Drum

(Set as a Factory Default)

Press the button below

“TRG” ([F3]).

The TRIGGER INST screen opens.

Use the [–] or [+] buttons

to select the number for

the Trigger Sound you

want to use.

Trigger Sound name

Trigger Sound number

About the “BYPASS”

In each screen, selecting “BYPASS” ([F3]) causes the corresponding knob lamps to

dimly flash and the Effect not applied. Each press of the [F3] button turns the bypass set-

ting on or off. When you select “BYPASS” while the knob is turned fully to the mini-

mum position, the two lamps below the knob dimly flash.

NOTE

To check the Trigger Sound, turn the

[TRIGGER] knob clockwise to

increase the volume.

EAD10 Owner’s Manual

Creating Your Own Scene

Basic Guide

 Advanced Trigger Sound Settings

When you attach a Drum Trigger on the snare drum, or add a DTX series pad, you need to assign a Trigger Sound to each

device to play Trigger Sounds. This section describes how to change instrument categories to assign different Trigger

Sounds, how to audition Trigger Sounds, and how to turn off the Trigger Sound by switching the “BYPASS” setting.

If you want to make more precise changes to the settings, press the [MENU] button to make detailed settings. For more

information, refer to the Reference Manual (Advanced) (PDF). (MENU/Scene Edit/Inst or MENU/Scene Edit/Voice)

Press the button

below “TRG” ([F3]).

Instrument category name

Trigger Sound number

Pad name

Trigger Sound name

The TRIGGER INST screen opens.

Switching the Instrument Category

Press the button below “ ” ([F1]) to

move the cursor to “Category” (instru-

ment category name).

Use the [–] or [+] buttons to select the

instrument category you want to use.

Next, move the cursor to Trigger Sound number using

the same procedure described in step 2, then select a

Trigger Sound using the same procedure as in step 3.

Auditioning Sounds

Press the button below “ ” ([F2]).

You can listen to the Trigger Sound.

Switching the Pad

Strike the separately sold add-

on pad to select the pad whose

sound you want to change.

Make sure that the pad name in the

upper right corner of the screen has

changed.

EAD10 Owner’s Manual

Creating Your Own Scene

Basic Guide

 Using Imported Sounds (.wav)

You can import audio files (.wav) into the EAD10 to use as Trigger Sounds.

For more information on importing audio files and settings, refer to the Reference Manual (Advanced) (PDF). (MENU/Job/

Wave)

For more information on using a USB flash drive, see “Using a USB Flash Drive” (page 30).

 Saving a Scene Under a New Name

Press the [STORE] button.

The STORE screen opens.

Press the button below “NAME” ([F2)] to

open the NAME screen.

Use the buttons below “<” or “>” ([F1] or

[F3]) to select the character position, then

use the [–] or [+] buttons to select a letter.

A name of up to 10 characters can be set to the Scene.

NOTE

You can also use the [SCENE] knob to select characters.

User Scene number and

User Scene name of the

Scene you are editing.

User Scene number and

User Scene name of the

Store Destination

Character position (cursor)

Character you

want to enter

EAD10 Owner’s Manual

Creating Your Own Scene

Basic Guide

After entering all characters, press the but-

ton below “OK” ([F2]) and return to the

STORE screen.

Use the [–] or [+] buttons to select a User

Scene Number to store your Scene to.

After confirming the new Scene Number and

Scene Name, press the button below

“STORE” ([F3]).

When the Store operation is complete, the display returns to the Scene screen.

NOTE

You can also use the [SCENE] knob to make changes.

NOTE

You cannot save an edited Scene to a Preset Scene.

NOTICE

When overwriting a Scene, the current Scene settings

are replaced with the new settings. Before overwriting a

Scene, ensure that the Scene contains no irreplaceable

settings.

“Overwrite?” appears when the selected Scene Number already con-

tains a Scene.

If you want to overwrite to save the Scene, press the button below

“YES” ([F1]).

If you do not want to overwrite, press the button below “NO” ([F3])

and return to the previous screen where you can select another Scene

number.

EAD10 Owner’s Manual

Using the Click (Metronome)

Basic Guide

Set the Click (Metronome) tempo, volume, type of sound, etc.

Press the [ ] (Click) button.

Using the Click (Metronome)

Press the [EXIT] but-

ton to return to the

previous screen or

the Scene screen.

The CLICK screen

opens.

Starting and

Stopping the Click

Press the button

below “ ” ([F1])

to start the Click.

The [CLICK] button flashes

in sync with the tempo while

the Click sounds.

Press the button

below “ ” ([F1])

to stop the Click.

NOTE

You can also press the [ ]

(Click) button to start the Click

and to stop the Click.

Setting Click Beat

Volumes and Types of

Sounds

Press the button

below “VOL/BEAT”

([F2]).

The VOLUME/BEAT screen

opens.

Tap the button at the desired tempo to set

the tempo.

Press the button below

“TAP” ([F3]).

The TAP screen opens.

Tap the button below “

TAP” ([F3]) at least 3 times.

The tapped tempo is detected and appears

on the screen.

NOTE

You can also set the tempo by striking the

bass drum or a pad connected to the Trig-

ger Input jacks.

Setting the Tempo by

Tapping the Button

(Tap Tempo)

Changing the

Tempo

Slower Faster

(continued to the next page)

EAD10 Owner’s Manual

Using the Click (Metronome)

Basic Guide

(continued from the previous page)

VOLUME/BEAT screen

3/8, 6/8, 9/8, 12/8, 15/8 beats only have settings for Acc, dotted quarter, eighth, and sixteenth

notes.

Set the volume

Set the time signature

Accents Quarter

notes

Eighth

notes

Sixteenth

notes

Eighth note

triplets

Beats

(1/4−16/4, 1/8−16/8,

1/16−16/16)

Setting Individual Click Beat

Volumes

Use the buttons below “<” or ”>” ([F1]

or [F2]) to move the cursor.

Use the [–] or [+] buttons to adjust the

volume.

Changing the Click Sounds

Press the button below “VOICE” ([F3]).

The CLICK VOICE screen opens.

Use the [–] or [+] buttons to change

the Click Sound.

EAD10 Owner’s Manual

Recording Your Performance

Basic Guide

Use the EAD10 to record your performance. When a USB flash drive is connected to the unit, audio is recorded to the USB

flash drive.

 Recording to the Main Unit (when no USB flash drive is connected

to the terminal)

Press the [RECORDER] button.

Recording Your Performance

The RECORDER screen opens.

Destination and elapsed playback time

(min: sec)

The [RECORDER] button lights while

recording or during playback.

Switching to AUX IN

Recording

Change the setting when recording

audio from the [AUX IN] jack.

For more information, see “Switching

to AUX IN Recording” on page 43.

Press the button

below “

” ([F1]) to

start recording.

While recording “Now recording

.. (elapsed recording time

(min:sec))” appears.

Play the drums.

After you finish play-

ing, press the button

below “ ” ([F1]) to

stop recording.

Recording

Playing Back

Press the “>” button

([F2]) to start play-

back.

To stop playback,

press the “

” button

([F2]).

NOTE

This is not displayed when there is

no recorded song.

NOTICE

• When your performance is already

recorded on the Main Unit, recording

again on the Main Unit erases the

previous recording.

• Any performance recorded to the

EAD10 Main Unit will be lost when the

power is turned off. Please export any

recorded performance data that you

wish to save.

NOTE

• Recording time to the Main Unit is about

1 minute 30 seconds.

• Press the [MENU] button to open the

Job screen from which you can export

your recording as a audio file. For more

information, refer to the Reference Man-

ual (Advanced) (PDF). (MENU/Job/

Recorder/Export Audio)

Press the [EXIT] button

to return to the Scene

screen.

EAD10 Owner’s Manual

Recording Your Performance

Basic Guide

 Recording to a USB Flash Drive

Connect a USB flash drive to the [USB TO DEVICE] terminal on the rear panel.

When a USB flash drive is connected

• You can record up to 30 minutes at a time.

• A new file is created every time you record.

• Simultaneously press Playback and Record to overdub your performance onto the

currently playing song.

Press the [EXIT] button to return

to the Scene screen.

The RECORDER

(USB) screen opens.

Song number and

elapsed playback time

(min:sec)

Press the button below

“

” ([F1]) to start

recording.

While recording “Now recording ..

(elapsed recording time

(min:sec))” appears.

Play the drums.

After you finish play-

ing, press the button

below “ ” ([F1]) to

stop recording.

The RECORDER SAVE screen

opens.

Press the button below

“SAVE” ([F3]) and

save the file.

Press the button below “CAN-

CEL” ([F2]) if you do not want to

save the file.

NOTE

If you want to change the file name,

press the button below “NAME”

([F1]) and enter a new name. (page

37)

Recording

File name

Switching to AUX IN Recording

Change the setting when recording audio from

the [AUX IN] jack.

For more information, see “Switching to AUX

IN Recording” on page 43.

Playing Back

Use the [–] or [+] buttons to

select a song for playback.

Press the button below “>”

([F2]) to start playback.

Press the button below

“

” ([F2]) to stop playback.

NOTE

This is not displayed when there is no

recorded song.

NOTE

Up to 100 songs are recognized.

Press the [RECORDER] button.

EAD10 Owner’s Manual

Recording Your Performance

Basic Guide

 Switching to AUX IN Recording

The Input Source must be changed to record from the [AUX IN] jack.

Press the [RECORDER] button.

Press the button below “SOURCE” ([F3]).

Press the button below “YES” ([F1]).

The setting is changed to the AUX IN recording.

After you finish recording, the EAD10 returns to the normal record settings.

NOTE

Your performance does not sound and is not recorded while

in AUX IN recording.

When recording to the Main Unit When recording to a USB flash drive

A confirmation message appears.

EAD10 Owner’s Manual

Recording Your Performance

Basic Guide

 Overdub Recording Your Performance onto an Accompaniment

Song

You can overdub your performance onto a accompaniment song that you’ve imported onto a USB flash drive and save your

performance combined with the accompaniment song as a single audio file.

 Preparing an Accompaniment Song (Audio File)

• Importing from a Computer

Save the audio file (.wav file) from the computer to the root directory on a USB flash drive.

• Importing from the [AUX IN] Jack

Connect a portable music player or other such device to the [AUX IN] jack on the rear panel, and have the song ready

for playback.

Recording the Accompaniment Song

Connect the USB flash drive to the [USB TO

DEVICE] terminal on the rear panel, then

connect a portable music player to the

[AUX IN] jack.

Press the [RECORDER] button.

The RECORDER (USB) screen opens.

NOTE

If you play along to a track coming into the Aux Input, only your performance will be recorded.

Audio file requirements: 16-bit, 44.1 kHz, stereo, wav format

NOTE

• Some of the audio files may not play back even when the above requirements are met.

• The EAD10 does not recognize the audio file if it is in a folder.

EAD10 Owner’s Manual

Recording Your Performance

Basic Guide

Press the button below “SOURCE” ([F3]).

The “Switch to AUX IN recording?” confirmation

screen appears.

Press the button below “YES” ([F1]), to

switch to AUX IN Recording.

Press the button below “” ([F1]) on the

EAD10 to start recording, and simultane-

ously press Playback on the portable music

player to start playback of the accompani-

ment song.

After the song playback finishes, press the

button below “ ” ([F1]) to stop recording.

The RECORDER SAVE screen opens.

Press the button below “SAVE” ([F3]), and

save the file.

Press the button below “CANCEL” ([F2]) if you do not

want to save the file.

By doing this, the external song you have just recorded is on the USB flash drive, ready for you to

use.

NOTE

If you want to change the file name, press the button below

“NAME” ([F1]) and enter a new name. (page 37)

EAD10 Owner’s Manual

Recording Your Performance

Basic Guide

 Recording Yourself Playing Along with the Accompaniment Song

Use the [–] or [+] buttons to select the

accompaniment you have prepared.

Press the button below “” ([F1]) and the

button below “>” ([F2]) to start recording

and playback.

Play the drums.

After you finish playing, press the button

below “ ” ([F1]) to stop recording.

You have now just recorded yourself over the song on the USB flash drive.

NOTE

Pressing the button below “” ([F2]) stops accompaniment

playback, but recording continues.

EAD10 Owner’s Manual

Recording Your Performance

Basic Guide

 Recording with Smart Device Apps

Using apps compatible with the EAD10 provides greater convenience and a more enjoyable user experience.

For more information on how to connect, refer to the “iPhone/iPad Connection Manual” (PDF) available at the Yamaha

website.

For details on compatible smart devices and applications, refer to the web page below.

http://download.yamaha.com/

 Recording to a Computer

You can connect to a computer and use DAW software to record your performance.

For more information on how to connect a computer, refer to the Reference Manual (Advanced) (PDF). For more informa-

tion on how to use the DAW software, refer to the Owner’s Manual for your DAW software.

NOTE

To eliminate the risk of interference due to noise by your iPhone or iPad when used in combination with the EAD10, turn on the Air-

plane Mode and then turn on Wi-Fi.

NOTICE

Be sure to place your iPhone or iPad on a stable surface to prevent it from falling over and being damaged.

What is DAW Software?

DAW is an abbreviation of Digital Audio Workstation and refers to applications such as Cubase that let you record, edit,

and mix audio on a computer.

EAD10 Owner’s Manual

Application Guide

You can connect add-ons (sold separately) to the Main Unit’s Trigger Input jacks or Footswitch jack and play Trigger

Sounds or switch functions.

Here are some of the things you can do with separately sold add-ons.

Connecting to the [qKICK/w]−[y] Jacks

(*1) About the Pads

Within this Owner’s Manual, the separately sold external pads that may be connected to the EAD10 are referred to by model

name. Please note that these model names were up-to-date as of printing of this manual. Details regarding any subsequently

released models will be made available via the following web site.

http://download.yamaha.com/

* Yamaha Corporation reserves the right to modify this URL at any time without prior notice.

Enhance Your Drum Set with Separately Sold Add-Ons

Separately sold add-ons Main applications

Drum Trigger

 page 50

 Attach a drum trigger to an acoustic drum and trigger a

sound from the EAD10 (including your own samples)

whenever the drum is played. The EAD10 will change the

volume of the sound depending on how hard you play.

Pad

(*1)

 page 52

 Play the EAD10 like an electronic drum module.

 The pads can also be used to perform in other ways such

as kit switching, turning functions on and off and many

others.

EAD10 Owner’s Manual

Enhance Your Drum Set with Separately Sold Add-Ons

Application Guide

Connecting to the [FOOT SW] Jack

* May not be available depending on your area. Check with your Yamaha dealer.

Separately sold add-ons Main applications

Pedal

 page 54

 Switch functions

 Play Trigger Sounds

Choose the pedal that best fits your needs.

NOTE

• In this manual, the term “FC3” refers to the FC3 and all other equivalent products, such as the FC3A.

• In this manual, the term “FC4” refers to the FC4 and all other equivalent products, such as the FC4A.

• Switch on or off

• Adjust volume (keeps its position when released)

• Switch on or off

• Play Trigger Sounds

• Switch on or off

• Adjust volume (pedal returns when released)

• Play Trigger Sounds

FC5

FC4

FC7

HH65

FC3

EAD10 Owner’s Manual

Enhance Your Drum Set with Separately Sold Add-Ons

Application Guide

 Using Drum Triggers to Play Trigger Sounds with Your Acoustic

Drums (with Drum Triggers)

Attach a Drum Trigger (sold separately) to the snare drum or tom, and connect the Drum Trigger to the Main Unit, you can

play Trigger Sounds according to the timing and intensity of each stroke. For example, layer internal drum sounds to

enhance the sound, or layer other instrument sounds like percussion or sound effects.

Drum Trigger Connection Examples

 Procedure:

Example) Connecting a DT50S Drum Trigger

Turn off the Main Unit.

Make sure the Main Unit is turned off before connecting.

Attach the DT50S between two of the tension

rods on the snare drum.

For more information, refer to the DT50S Owner’s Man-

ual.

NOTE

Position the Drum Trigger far from the drummer to prevent it

from being struck accidentally.

DT50S

Main Unit

All off

Head

Clamp screw

Hoop

DT50S

EAD10 Owner’s Manual

Enhance Your Drum Set with Separately Sold Add-Ons

Application Guide

Connect the DT50S to the [eSNARE/r] jack

on the Main Unit rear panel.

Press the [MENU] button to make necessary

settings for using DT50S.

When the DT50S is connected to the [eSNARE/r] jack,

settings can be used as they are, without having to make

any changes. When any other drum trigger is connected,

perform the following settings.

• Specify the type of trigger that is connected

Select the appropriate pad from the pad type list. For

more information, refer to the Reference Manual

(Advanced) (PDF). (MENU/Trigger/Pad Type)

• Specify the function of the connected trigger

Play trigger sounds (page 35)

This completes set up.

Main Unit

DT50S

EAD10 Owner’s Manual

Enhance Your Drum Set with Separately Sold Add-Ons

Application Guide

 Using Electronic Drum Pads to Play Sounds or Control Functions

(with Add-on Pads)

You can play drum, percussion or other sounds, or control functions using pads (sold separately) connected to the Main

Unit.

Pad Connection Example

 Procedure:

Example) Connecting a TP70S

Turn off the Main Unit.

Make sure the Main Unit is turned off before connecting.

Attach the pad.

Pad

Main Unit

All off

Clamp rod

Example

Cymbal

stand

Electronic Drum Pad

(TP70S)

Cymbal stand attachment

CSAT924A

EAD10 Owner’s Manual

Enhance Your Drum Set with Separately Sold Add-Ons

Application Guide

Connect the TP70S to the [t] or [y] jack on

the Main Unit rear panel.

Turn on the Main Unit.

Press the [MENU] button to make necessary

settings for using TP70S.

When the TP70S is connected to the [t] jack or [y]

jack, settings can be used as they are, without having to

make any changes. When any other pad is connected, per-

form the following settings.

• Specify the type of pad that is connected

Select the appropriate pad from the pad type list. For

more information, refer to the Reference Manual

(Advanced) (PDF). (MENU/Trigger/Pad Type)

• Specify the function of the connected pad

• Play trigger sounds (page 35)

• Switch functions (refer to the Reference Manual

(Advanced) (PDF)) (MENU/Utility/PadFunction)

This completes set up.

Main Unit

EAD10 Owner’s Manual

Enhance Your Drum Set with Separately Sold Add-Ons

Application Guide

 Using a Pedal to Play Sounds or Control Functions (with a Foot

Pedal or a Foot Controller)

You can connect a foot pedal to the [FOOT SW] jack for a variety of uses.

 Procedure:

Example) Connecting an HH65

Turn off the Main Unit.

Make sure the Main Unit is turned off before connecting.

Connect the pedal’s plug to the [FOOT SW]

jack on the Main Unit rear panel.

Plug the other end of the cable that came with the HH65

into the [OUTPUT] jack on the HH65.

Turn the Main Unit on.

Press the [MENU] button to carry out the initial

setting.

When the HH65 is connected, settings can be used as they

are without having to make any changes. Perform the fol-

lowing settings when connecting any other pedal.

• Specify the type of pedal that is connected

Select the pedal you connected from MENU/Trigger/

FootSwSelect

• Specify the function of the connected pedal

• Specify the function of the connected pedal (MENU/

Utility/PadFunction)

• Select the Trigger Sound (to play sounds) (page 35)

This completes set up.

All off

HH65

Main Unit

EAD10 Owner’s Manual

Reference

Menu List

Scene Edit

Inst

Category . . . . . . . . . . . . . . . . . . . . . Instrument Category

InstNumber . . . . . . . . . . . . . . . . . . . Instrument Number

InstTune . . . . . . . . . . . . . . . . . . . . . . Instrument Tuning

InstDecay . . . . . . . . . . . . . . . . . . . . . Instrument Decay

InstPan . . . . . . . . . . . . . . . . . . . . . . . Instrument Pan

Voice

Category . . . . . . . . . . . . . . . . . . . . . Voice Category

VoiceNumber . . . . . . . . . . . . . . . . . . Voice Number

VoiceTune . . . . . . . . . . . . . . . . . . . . Voice Tuning

VoiceDecay . . . . . . . . . . . . . . . . . . . Voice Decay

VoicePan . . . . . . . . . . . . . . . . . . . . . Voice Pan

VoiceFilter . . . . . . . . . . . . . . . . . . . . Voice Filter Cutoff Frequency

VoiceQ . . . . . . . . . . . . . . . . . . . . . . . Voice Filter Resonance (Q)

VoiceAltGrp . . . . . . . . . . . . . . . . . . . Voice Alternate Group

VoiceHoldMode . . . . . . . . . . . . . . . . Voice Hold Mode

MessageType . . . . . . . . . . . . . . . . . Select MIDI Message Type

Effect

ReverbType . . . . . . . . . . . . . . . . . . . Reverb Type

ReverbSend . . . . . . . . . . . . . . . . . . .

Reverb Send

RevReturn . . . . . . . . . . . . . . . . . . . . Reverb Return

Mic RevSend . . . . . . . . . . . . . . . . . . Mic Reverb Send

TriggerRevSend . . . . . . . . . . . . . . . . Trigger Sound Reverb Send

Voice RevSend . . . . . . . . . . . . . Trigger Sound Voice Reverb Send

MicEffType . . . . . . . . . . . . . . . . . . . . Mic Effect Type

MicEffDepth . . . . . . . . . . . . . . . . . . . Mic Effect Depth

TrgEffType . . . . . . . . . . . . . . . . . . . . Trigger Sound Effect Type

TrgEffSend . . . . . . . . . . . . . . . . . . . . Trigger Sound Effect Send and Dry Balance

TrgEffReturn . . . . . . . . . . . . . . . . . . Trigger Sound Effect Return

TrgEffToRev . . . . . . . . . . . . . . . . . . Trigger Voice Effect Reverb Send

Volume

Scene Volume . . . . . . . . . . . . . . . . . Overall Scene Volume

Mic Volume . . . . . . . . . . . . . . . . Mic Volume

TriggerVolume . . . . . . . . . . . . . . Trigger Sound Overall Volume

Inst Volume . . . . . . . . . . . . . Trigger Sound Instrument Volume

Voice Volume . . . . . . . . Trigger Sound Voice Volume

Tempo . . . . . . . . . . . . . . . . . . . . . . . . . . Tempo for Selected Scene

EAD10 Owner’s Manual

Menu List

Reference

Trigger

Input Mode

Trg1/Trg2 . . . . . . . . . . . . . . . Trigger 1/Trigger 2 Input Mode

Trg3/Trg4 . . . . . . . . . . . . . . . Trigger 3/Trigger 4 Input Mode

Curve

Velocity Curve . . . . . . . . . . . Velocity Curve

Pad Type

PadType . . . . . . . . . . . . . . . Select Pad Type

Gain . . . . . . . . . . . . . . . . Gain

Sensitivity . . . . . . . . . . . Sensitivity

RejectTime . . . . . . . . . . Reject Time

MinLevel . . . . . . . . . . . . Minimum Level

MaxLevel . . . . . . . . . . . . Maximum Level

MinVelocity . . . . . . . . . . Minimum Velocity

MaxVelocity . . . . . . . . . . Maximum Velocity

WaitTime . . . . . . . . . . . . Wait Time

RimGain . . . . . . . . . . . . Rim Gain

H/R Balance . . . . . . . . . H/R Balance

Crosstalk

All Reject Lvl . . . . . . . . . . . . All Rejection Level

Reject Lvl . . . . . . . . . . . . . . . Rejection Level (Source Pad)

FootSwSelect . . . . . . . . . . . . . . . Select Foot Switch

Utility

General

SceneKnob . . . . . . . . . . . . . Scene Knob

AutoPowerOff . . . . . . . . . . . Auto Power Off

LCD Contrast . . . . . . . . . . . . LCD Contrast

ClickOutput . . . . . . . . . . . . . Click Output Destination

ClickCountOff . . . . . . . . . . . . Click Countoff

L&R Volume . . . . . . . . . . . . . External Device Output Volume

MicNoiseGate . . . . . . . . . . . Mic Noise Gate

AudioOutGain . . . . . . . . . . . Audio Out Gain

AudioMix . . . . . . . . . . . . . . . Audio Mix

USB To Host . . . . . . . . . . . . [USB TO HOST] Terminal Setting

MIDI LocalCtrl . . . . . . . . . . . MIDI Local Control

AuxInVolume . . . . . . . . . . . . [AUX IN] Volume

USB Volume . . . . . . . . . . . . USB Audio or Recorder Playback Volume

ClickVolume . . . . . . . . . . . . . Click Volume

PadFunction

PadFunction . . . . . . . . . . . . . Pad Function

BypassSw . . . . . . . . . . . . . . Bypass Switch

Phones EQ

EQ Lo

wGain . . . . . . . . . . . . EQ Low Gain

EQ HighGain . . . . . . . . . . . . EQ High Gain

EAD10 Owner’s Manual

Menu List

Reference

Job

Scene

Recall . . . . . . . . . . . . . . . Recall

Sort . . . . . . . . . . . . . . . .Sort

Exchange . . . . . . . . . . . . Exchange

Clear . . . . . . . . . . . . . . .Clear

Wave

Import . . . . . . . . . . . . . . . Import Selected Audio File

Import All . . . . . . . . . . . . Import All Audio Files

Delete . . . . . . . . . . . . . . Delete Selected Audio File

Delete All . . . . . . . . . . . .Delete All Audio Files

Optimize . . . . . . . . . . . . . Optimize Memory

Memory Info . . . . . . . . . . Memory Information

Recorder

Export Audio . . . . . . . . . Export Audio

File

Save . . . . . . . . . . . . . . . . . . .Save File

Load . . . . . . . . . . . . . . . . . . . Load File

Rename . . . . . . . . . . . . . . . . Rename File

Delete . . . . . . . . . . . . . . . . . .Delete File

Format . . . . . . . . . . . . . . . . . Format USB Flash Drive

Memory Info . . . . . . . . . . . . . USB Flash Drive Memory Information

Factory Reset . . . . . . . . . . . . . . . Factory Reset

EAD10 Owner’s Manual

Troubleshooting

Reference

Troubleshooting

Symptom Possible cause Solution Reference page

No sound EAD10 is not turned on Make sure that the power is turned

on.

page 25

The volume is not turned up Check the [MASTER VOLUME]

knob setting.

page 13

The cable is not properly connected

The cable is damaged

Make sure that the Sensor Unit and

Main Unit are properly connected

with a stereo phone cable.

page 17

Make sure the cable you are using

is in good condition.

Make sure that the Main Unit is

properly connected to headphones

or other audio equipment, such as

an amplifier and/or speakers.

Make sure that the ”A” cable is con-

nected to the [A] jacks, and the “B”

cable is connected to the [B] jacks.

The volume setting is improper. Check the [MASTER VOLUME]

knob setting.

Check the power and volume set-

tings on the external devices.

page 13

Poor volume balance

Poor volume balance between

the Mic Sound and Trigger

Sound

Adjust the Trigger Sound volume. If

it does not solve the problem, adjust

the mic gain.

page 34

page 28

Poor volume balance between

the AUX IN and your perfor-

mance

Adjust the volume on the device

connected to the [AUX IN] jack.

Adjust the [AUDIO/CLICK VOL-

UME] knob.

page 13

Poor volume balance between

the USB flash memory playback

and your performance

Adjust the [AUDIO/CLICK VOL-

UME] knob.

page 13

Cymbals sound distant or vol-

ume of some drums is low

Instruments placed far from the

Sensor Unit may sound low in vol-

ume. Check the positions of drums

and cymbals in the drum set.

page 17

The bass drum Trigger Sound

does not play

Trigger settings are improper. Try using the automatic setting to

set up the Sensor Unit.

page 27

Sensor Unit not properly attached Make sure the Sensor Unit is prop-

erly attached to the hoop.

page 17

EAD10 Owner’s Manual

Troubleshooting

Reference

Hard to notice changes to settings Reverb/Effect level or Trigger Sound

volume is too low

Turn the [REVERB] knob,

[EFFECT] knob, or [TRIGGER]

knob to the right to adjust depth or

volume.

page 33

The Mic Gain is set too low Try using the automatic setting to

set up the Sensor Unit.

page 27

Trigger settings are improper

The volume for the headphones you

are using is low

Use highly-efficient headphones,

closed-ear headphones, or ear-

phones.

page 23

Noise occurs Noise from the mic Secure the cables close to the Sen-

sor Unit using the supplied cable

band tape so that the cables do not

move about near the Sensor Unit.

page 17

Make sure the Sensor Unit is prop-

erly attached to the hoop.

Secure the cable connected to the

[B] jack (Mic Sensor cable) on the

Main Unit using the supplied cable

bands to prevent the cables from

moving about.

Multiple sounds produced with a

single strike (double trigger)

Double triggers are occurring Make sure the Sensor Unit is prop-

erly attached to the hoop.

page 17

The longer the bass drum head

vibrates, the easier it is to cause

double triggers.

Adjust the bass drum so it produces

a shorter sound. Try muting or tun-

ing the head or changing the head.

Separately sold add-on pads do not

sound

Hard to produce sound

Make sure the pad type setting is

correct.

Reference Manual

(Advanced) (PDF)

Sound is produced without striking

the pad

Sound is produced by a pad that

was not struck

Crosstalk is occurring Increase the Trigger Sound mini-

mum level setting. Setting this too

high, however, can prevent light

strokes from producing a sound.

Adjust as necessary.

page 33

Reference Manual

(Advanced) (PDF)

Crosstalk is occurring with the bass

drum Trigger Sound

Try using the automatic setting to

set up the Sensor Unit. Check the

Trigger Sensitivity setting.

page 27

If the bass drum sound plays when

striking the snare drum, move the

snare drum farther away from the

Sensor Unit. More distance

between the two might improve the

problem.

page 17

Symptom Possible cause Solution Reference page

EAD10 Owner’s Manual

Troubleshooting

Reference

*1 Refer to the website at http://download.yamaha.com/

*URL may change without notice.

Sound is distorted Mic gain level is set too high Press the [ ] button and adjust the

mic sensor settings.

page 27

The Master Volume is set too high Turn the [MASTER VOLUME] knob

to the left.

page 13

An Effect is applied Adjust the distortion or other Effect

setting.

page 13

Cannot record the Main Unit

Cannot record to a USB flash drive

Cannot record audio from the AUX IN The sound of your performance and

the audio from the AUX IN cannot

be recorded simultaneously.

Audio from the AUX IN must first be

recorded to the Main Unit, then you

can overdub your performance onto

the song.

page 41

Cannot record the Click EAD10 is not designed to record

the Click.

Not enough memory in the USB flash

drive

Check the available memory in the

USB flash drive.

The USB flash drive is write protected Disable the write protection from the

USB flash drive.

Audio files recorded on a USB flash

drive have low volume when playing

back on the Main Unit

Adjust the volume to an appropriate

level when recording.

Adjust the [AUDIO/CLICK VOL-

UME] knob during playback.

Record:

Reference Manual

(Advanced) (PDF)

Playback:

page 13

The audio file in the USB flash drive

cannot be played back with the Main

Unit

Playback stops in the middle of a

song when playing back the audio

file from the USB flash drive

Unsupported file format Check the file format or the sam-

pling frequency.

page 63

The USB flash drive performance is

insufficient.

We recommend using a USB flash

drive of 4GB or more. For more

information, refer to the “Compati-

ble USB Device List” on the

Yamaha web site.

Power turns off unexpectedly The Auto Power-Off function is

enabled

Disable the Auto Power-Off func-

tion.

page 29

Does not turn on The AC adaptor is not connected Make sure the AC adaptor is con-

nected.

page 22

Edits made to the Scene are lost Before storing the edits, another

Scene was selected

Use the Recall function to recall the

edited contents.

page 34

Symptom Possible cause Solution Reference page

EAD10 Owner’s Manual

Message List

Reference

Message List

Message Description

Are you sure? Confirms whether or not you want to execute the specified operation.

Auto power off disabled. Appears when the [STORE] button is held down while turning on the

power informing the user that the Auto Power Off function is dis-

abled.

Backup error. Appears when writing data to the Flash ROM has failed.

If data was not be properly saved when turning off the unit, this mes-

sage appears the next time the power is turned on. After the error

message appears, the Factory Reset automatically executes.

Cancel AUX IN recording? Appears when the SOURCE button is pressed while the Recorder is

in AUX IN Recording. Press the button below “YES” to return to the

normal Recorder setting.

Canceled. Appears when the cancel operation is complete.

Can’t use RECORDER now. Cannot use the recorder because “USB To Host” is set to “audio.”

Check the “USB to Host” setting.

Completed. Appears when execution of a Scene Store, File Load/Save, Job, or

other function is complete.

Connecting USB device... Appears when connecting to a USB device.

Excessive demand for USB power. Power consumption of the USB device exceeds the specified value.

Factory Reset initializing... Appears on startup if you did a factory reset.

File already exists. A file with the same name already exists.

File not found. The selected file type was not found.

Illegal file. Appears when loading a file and the Main Unit cannot handle the tar-

get file or does not support the audio file.

Incompatible USB device. Appears when an unsupported USB device is connected to the [USB

TO DEVICE] terminal.

Invalid USB device. The USB device is faulty. Format the USB device again.

No data. Appears when the target data does not exist when using the

Recorder or using Wav-related parameters under “Job.”

No response from USB device. There is no response from the USB device.

Now importing... Appears when importing a .wav file.

Now loading... Appears when loading a file.

Now processing... Appears when executing a Scene Store or Job operation. Appears

during post-processing after canceling the File Load or File Save

operation.

Now saving... Appears when saving a file.

Now switching audio driver. Appears when the [USB TO HOST] terminal is connected to a com-

puter or other device and the following operation is performed.

When changing the “USB To Host” setting to “MIDI” or “MIDI+audio.”

When entering or exiting the Recorder screen when the "USB To

Host" setting is “auto.”

Overwrite? Appears when saving a file to the USB device and a file with the

same name already exists in the USB device.

Appears when attempting to rerun the Store User Scene operation

for the Scene previously saved.

EAD10 Owner’s Manual

Message List

Reference

*1 Refer to the website at http://download.yamaha.com/

*URL may change without notice.

Please stop recorder. Appears when performing an operation that exits the Recorder dur-

ing recorder playback or recording. Stop the Recorder and try again.

Recording time limit exceeded. Recording time is about 1 minute 30 seconds with internal memory,

and about 30 minutes with a USB flash drive.

Read only file. Appears when a read-only file is selected during a file operation.

Sample is too long. Sample is too long and cannot be loaded.

Sample is too short. Sample is too short and cannot be loaded.

Switch to AUX IN recording? Appears when the button below “source” is pressed while using the

recorder. Press the button below “YES” and switch to recording from

the [AUX IN] jack.

USB connection terminated. Appears if connection with the USB device was interrupted by an

abnormal electric current. Disconnect the USB device and press the

button below “OK”.

USB device’s transfer speed too slow. Appears when the transfer speed to the USB device is insufficient.

For information on devices that have been tested and confirmed to

work properly with the EAD10, refer to the “Compatible USB Device

List”

(*1)

on the Yamaha web site.

USB device full. Appears when the USB device is full and files cannot be saved on it.

Use a new USB device or make space by erasing unnecessary files

from the full device.

USB device not ready. Appears if the USB device is not properly connected to the Main

Unit.

USB device read/write error. Appears if an error occurred while reading or writing data to the USB

device.

USB device write protected. Appears if the USB device is write-protected.

USB transmission error. Appears if an error occurred while communicating with the USB

device.

Wave memory full. Appears if the WAVE memory is full and operations such as Import,

Job, or Load cannot be carried out.

Message Description

EAD10 Owner’s Manual

Specifications

Reference

Main Unit

Sensor Unit

Other

* The contents of this manual apply to the latest specifications as of the publishing date.

To obtain the latest manual, access the Yamaha website then download the manual file.

Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.

Specifications

Tone

Generator

Block

Scenes Preset: 50

User: 200

Reverb 11

Effects Mic: 21, Trigger: 10

Trigger Sounds Tone generator AWM2

Maximum polyphony 64

Voices 757

Recorder Recording time Internal memory Approx. 1 min 30 sec

USB flash drive Approx. 30 min/file

Format Record/playback WAV (44.1 kHz, 16 bit, stereo)

Audio Files Import limit Up to 100

Playback sample rate 44.1 kHz

Wave memory 32 MB

Maximum loadable sample size 1 mono sample: 1.75 MB

1 stereo sample: 3.5 MB

Sample format WAV (16 bit)

Click-track Tempo 30−300 BPM, tap tempo function

Time signatures 1/4 to 16/4, 1/8 to 16/8, 1/16 to 16/16

Subdivisions Accents, quarter notes, eighth notes, sixteenth notes, and

eighth-note triplets

Functions Trigger sensitivity adjustment, USB audio/MIDI, headphone EQ

Control

Interface

Display Full Dot LCD (128 × 64 dot)

Other Controllers Knobs MASTER VOLUME, AUDIO/CLICK VOLUME, SCENE, REVERB,

EFFECT, TRIGGER

Buttons MENU, Sensor Unit, Click, RECORDER, EXIT, STORE, Functions 1–3,

–, +, Standby/On

Connectivity DC IN DC IN (12 V)

Headphones PHONES (standard stereo phone jack)

AUX IN AUX IN (stereo mini jack)

OUTPUT OUTPUT L/MONO, R (standard phone jack)

USB USB TO DEVICE

USB TO HOST

Sensor input For Trigger sensor A (standard stereo phone jack)

For Mic sensor B (standard stereo phone jack)

Trigger input Stereo (L: trigger, R: trigger) qKICK/w (also serves as A), eSNARE/r (standard stereo phone jack)

Three-zone (L: trigger, R: rim switch) t, y (standard stereo phone jack)

Foot Pedal FOOT SW (standard stereo phone jack)

Power Supply Power Supply PA-150 (or an equivalent recommended by Yamaha)

Power Consumption 10 W (when using PA-150 AC adaptor)

Auto Power Off Yes

Size/Weight Dimensions (W × D × H) Width × depth × height 260 (W) × 138 (D) × 63 (H) mm (10 1/4" × 5 7/16" × 2 1/2")

Weight Main Unit only 654 g (1 lb 7 oz)

Sensor Types Microphone High SPL mic × 2

Trigger Exclusive for bass drum × 1

Connectivity Sensor outputs For Trigger sensor A (standard phone jack)

For Mic sensor B (standard stereo phone jack)

Size/Weight Dimensions (W × D × H) Width × depth × height 76 (W) × 78 (D) × 88 (H) mm (3" × 3 1/16" × 3 7/16")

Weight Sensor Unit only 464 g (1 lb)

Included Accessories Owner’s Manual (this book), PA-150 (or an equivalent recommended by Yamaha)*, Module holder,

Module holder wing bolts (× 2), Connector cables (1 pair), Cable bands (× 3), Adhesive cushions (× 2)

*May not be included depending on your area. Check with your Yamaha dealer.

Separately Sold Accessories

(May not be available depending on

your area.)

• Cymbal stand attachment (CSAT924A)

• Please check the website for more information on other available accessories (http://download.yamaha.com/)

EAD10 Owner’s Manual

Index

Reference

Symbols

[ ] (Click) button .......................... 13

[ ] (Sensor Unit) button ......... 13, 27

[ ] (Standby/On) switch ......... 13, 25

[–] button, [+] button....................... 13

Numerics

[qKICK/w] ................................... 16

[eSNARE/r] ............................... 16

[t] ................................................ 16

[y] ................................................ 16

[A] jack .......................................... 15

AC adaptor ................................9, 22

Accompaniment Song...................44

Adhesive cushions ..........................9

[AUDIO/CLICK VOLUME] knob .... 13

audio file...................................37, 44

audio signal................................... 11

Auto Power-Off ..............................29

Auto setting ................................... 27

[AUX IN] (auxiliary input) jack ....... 14

AUX IN Recording ......................... 43

[B] jack .......................................... 15

BYPASS ........................................35

Cable bands ....................................9

Clamp screw ................................. 15

Click ..............................................39

Computer ................................ 25, 47

Connector cables ............................9

Cord hook...................................... 14

DAW Software...............................47

DC IN jack..................................... 14

Display .......................................... 13

double bass drum set ups............. 17

drum set ........................................ 17

Drum Trigger ...........................48, 50

E mark........................................... 33

[EFFECT] knob ............................. 13

Effects ..................................... 11, 32

[EXIT] button ................................. 13

[F1], [F2], [F3] ............................... 13

Factory Reset................................ 30

Foot Controller .............................. 54

Foot Pedal..................................... 54

[FOOT SW] Jack........................... 14

Front Panel.................................... 15

Function Buttons 1–3 .................... 13

Gain .............................................. 27

Headphones ................................. 23

Hoop ............................................. 18

Imported Sounds .......................... 37

Input Source.................................. 43

internal Voices................................11

iPhone/iPad................................... 47

[L] (Mic gain left)............................ 28

Main Unit................................. 10, 13

[MASTER VOLUME] knob ............ 13

[MENU] button............................... 13

Metal hoops .................................. 18

Metronome.................................... 39

MIC ............................................... 27

Mic gain......................................... 27

Mic Sensor.................................... 15

Mic sound ......................................11

Module holder ........................... 9, 20

Module holder wing bolts ................ 9

OUTPUT [R]/[L/MONO] jacks ....... 14

PA System..................................... 24

Pad.......................................... 48, 52

Pedal............................................. 49

[PHONES] jack ............................. 15

Portable Music Player ................... 24

Preset Scene................................. 34

[R] (Mic gain right) ........................ 28

Rear Panel.................................... 14

[RECORDER] button .................... 13

Reverb .....................................11, 32

[REVERB] knob ............................ 13

Scene ........................................... 32

[SCENE] knob .............................. 13

Scene Screen ............................... 33

Sensor Unit........................10, 15, 27

Separately Sold Add-Ons ............. 48

Store ............................................. 33

[STORE] button....................... 13, 37

Tap Tempo .................................... 39

Tempo ........................................... 39

TO SENSOR UNIT [A] jack........... 14

TO SENSOR UNIT [B] jack........... 14

Top Panel...................................... 13

TRG .............................................. 27

TRG SENS (Trigger Sensitivity).... 28

Trigger gain ................................... 27

Trigger Input Jacks...................14, 16

[TRIGGER] knob .......................... 13

Trigger sensor ............................... 15

trigger signal ..................................11

Trigger Sound ............................... 32

USB Flash Drive ..................... 30, 42

[USB TO DEVICE] terminal .... 14, 30

[USB TO HOST] terminal........ 14, 25

User Scene................................... 34

.wav .............................................. 37

Wood hoops.................................. 18

Y-cable .......................................... 16

Index

EAD10 Owner’s Manual

LIMITED WARRANTY ON YAMAHA DRUMS, HARDWARE AND ACCESSORY PRODUCTS

Thank you for selecting a YAMAHA product. YAMAHA products are designed and manufactured to provide a high level of defect-free performance. Yamaha

Corporation of America (“YAMAHA”) is proud of the experience and craftsmanship that goes into each and every YAMAHA product. YAMAHA sells its products

through a network of reputable, specially authorized dealers and is pleased to offer you, the Original Owner, the following Limited Warranty, which applies only to

products that have been (1) directly purchased from YAMAHA’s authorized dealers in the fifty states of the USA and District of Columbia (the “Warranted Area”) and

(2) used exclusively in the Warranted Area. YAMAHA suggests that you read the Limited Warranty thoroughly, and invites you to contact your authorized YAMAHA

dealer or YAMAHA Customer Service if you have any questions.

THIS WARRANTY COVERS THE LISTED PRODUCTS AGAINST DEFECTS IN MATERIALS OR WORKMANSHIP.

Warranty Term

Duration of Warranty from Date of

Type of Product Purchase by or for the Original Owner

Acoustic Drum Shells, Finish, Drum Hardware, Freestanding Hardware, Pedals, Hardware Accessories 5 Years

Electronic Drums Modules, Pads, Accessories, Hardware, Pedals 1 Year

Coverage: YAMAHA will, at its option, repair or replace the product covered by this warranty if it becomes defective, malfunctions or otherwise fails to conform

with this warranty under normal use and service during the term of this warranty, without charge for labor or materials. Repairs may be performed using new or

refurbished parts that meet or exceed YAMAHA specifications for new parts. If YAMAHA elects to replace the product, the replacement may be a reconditioned unit.

You will be responsible for any installation or removal charges and for any initial shipping charges if the product(s) must be shipped for warranty service. However,

YAMAHA will pay the return shipping charges to any destination within the USA if the repairs are covered by the warranty. This warranty does not cover (a) damage,

deterioration or malfunction resulting from accident, negligence, misuse, abuse, improper installation or operation or failure to follow instructions according to the

Owner’s Manual for this product; any shipment of the product (claims must be presented to the carrier); repair or attempted repair by anyone other than YAMAHA

or an authorized YAMAHA Service Center; (b) any unit which has been altered or on which the serial number has been defaced, modified or removed; (c) normal

wear and any periodic maintenance; (d) deterioration due to perspiration, corrosive atmosphere or other external causes such as extremes in temperature or

humidity; (e) damages attributable to power line surge or related electrical abnormalities, lightning damage or acts of God; or (f) RFI/EMI (Interference/noise)

caused by improper grounding or the improper use of either certified or uncertified equipment, if applicable. Any evidence of alteration, erasing or forgery of proof-

of-purchase documents will cause this warranty to be void. This warranty covers only the Original Owner and is not transferable.

In Order to Obtain Warranty Service: Warranty service will only be provided for defective products within the Warranted Area. Contact your local authorized

YAMAHA dealer who will advise you of the procedures to be followed. If this is not successful, contact YAMAHA at the address, telephone number or website

shown below. YAMAHA may request that you send the defective product to a local authorized YAMAHA Servicer or authorize return of the defective product to

MAHA for repair. If you are uncertain as to whether a dealer has been authorized by YAMAHA, please contact YAMAHA’s Service Department at the number

shown below, or check Yamaha’s website at http://usa.yamaha.com. Product(s) shipped for service should be packed securely and must be accompanied by a

detailed explanation of the problem(s) requiring service, together with the original or a machine reproduction of the bill of sale or other dated, proof-of-purchase

document describing the product, as evidence of warranty coverage. Should any product submitted for warranty service be found ineligible therefore, an estimate

of repair cost will be furnished and the repair will be accomplished only if requested by you and upon receipt of payment or acceptable arrangement for payment.

Limitation of Implied Warranties and Exclusion of Damages: ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE APPLICABLE PERIOD OF TIME SET FORTH ABOVE. YAMAHA SHALL NOT BE RESPONSIBLE

FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE, DAMAGE TO ANY OTHER EQUIPMENT OR

OTHER ITEMS AT THE SITE OF USE OR INTERRUPTION OF PERFORMANCES OR ANY CONSEQUENCES. YAMAHA’S LIABILITY FOR ANY DEFECTIVE PRODUCT IS

LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, AT YAMAHA’S OPTION. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED

WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY

NOT APPLY TO YOU. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This is the only express

warranty applicable to the product specified herein; Yamaha neither assumes nor authorizes anyone to assume for it any other express warranty.

If you have any questions about service received or if you need assistance in locating an authorized YAMAHA Servicer, please contact:

CUSTOMER SERVICE

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, California 90620-1373

Telephone: 800-854-1569

• http://usa.yamaha.com

Do not return any product to the above address without a written Return Authorization issued by YAMAHA.

Drums

Limited

Warranty

EAD10 Owner’s Manual

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au

distributeur le plus proche de vous figurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana o

el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Toronto, Ontario M1S 3R1, Canada

Tel: +1-416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620,

U.S.A.

Tel: +1-714-522-9011

MEXICO

Yamaha de México, S.A. de C.V.

Av. Insurgentes Sur 1647 Piso 9, Col. San José

Insurgentes, Delegación Benito Juárez, México, D.F.,

C.P. 03900, México

Tel: +52-55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B – Vila

Olímpia – CEP 04551-010 – São Paulo/SP, Brazil

Tel: +55-11-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.,

Sucursal Argentina

Olga Cossettini 1553, Piso 4 Norte,

Madero Este-C1107CEK,

Buenos Aires, Argentina

Tel: +54-11-4119-7000

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Edif. Torre Banco General, F7, Urb. Marbella,

Calle 47 y Aquilino de la Guardia, Panama,

P.O.Box 0823-05863, Panama, Rep.de Panama

Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND

Yamaha Music Europe GmbH (UK)

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, U.K.

Tel: +44-1908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH, Branch

Switzerland in Thalwil

Seestrasse 18a, 8800 Thalwil, Switzerland

Tel: +41-44-3878080

AUSTRIA/CZECH REPUBLIC/HUNGARY/

ROMANIA/SLOVAKIA/SLOVENIA

Yamaha Music Europe GmbH, Branch Austria

Schleiergasse 20, 1100 Wien, Austria

Tel: +43-1-60203900

POLAND

Yamaha Music Europe GmbH

Sp.z o.o. Oddział w Polsce

ul. Wielicka 52, 02-657 Warszawa, Poland

Tel: +48-22-880-08-88

BULGARIA

Dinacord Bulgaria LTD.

Bul.Iskarsko Schose 7 Targowski Zentar Ewropa

1528 Sofia, Bulgaria

Tel: +359-2-978-20-25

MALTA

Olimpus Music Ltd.

Valletta Road, Mosta MST9010, Malta

Tel: +356-2133-2093

NETHERLANDS/BELGIUM/

LUXEMBOURG

Yamaha Music Europe, Branch Benelux

Clarissenhof 5b, 4133 AB Vianen, The Netherlands

Tel: +31-347-358040

FRANCE

Yamaha Music Europe

7 rue Ambroise Croizat, Zone d'activités de Pariest,

77183 Croissy-Beaubourg, France

Tel: +33-1-6461-4000

ITALY

Yamaha Music Europe GmbH, Branch Italy

Via Tinelli N.67/69 20855 Gerno di Lesmo (MB), Italy

Tel: +39-039-9065-1

SPAIN/PORTUGAL

Yamaha Music Europe GmbH Ibérica, Sucursal en

España

Ctra. de la Coruna km. 17,200, 28231

Las Rozas de Madrid, Spain

Tel: +34-91-639-88-88

GREECE

Philippos Nakas S.A. The Music House

19th klm. Leof. Lavriou 190 02 Peania – Attiki, Greece

Tel: +30-210-6686260

SWEDEN

Yamaha Music Europe GmbH Germany filial

Scandinavia

JA Wettergrensgata 1, 400 43 Göteborg, Sweden

Tel: +46-31-89-34-00

DENMARK

Yamaha Music Denmark,

Fillial of Yamaha Music Europe GmbH, Tyskland

Generatorvej 8C, ST. TH., 2860 Søborg, Denmark

Tel: +45-44-92-49-00

FINLAND

F-Musiikki Oy

Antaksentie 4

FI-01510 Vantaa, Finland

Tel: +358 (0)96185111

NORWAY

Yamaha Music Europe GmbH Germany -

Norwegian Branch

Grini Næringspark 1, 1332 Østerås, Norway

Tel: +47-6716-7800

ICELAND

Hljodfaerahusid Ehf.

Sidumula 20

IS-108 Reykjavik, Iceland

Tel: +354-525-5050

CROATIA

Euro Unit D.O.O.

Slakovec 73

40305 Nedelisce

Tel: +38540829400

RUSSIA

Yamaha Music (Russia) LLC.

Room 37, entrance 7, bld. 7, Kievskaya street, Moscow,

121059, Russia

Tel: +7-495-626-5005

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

Yamaha Music Gulf FZE

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

TURKEY

Yamaha Music Europe GmbH

Merkezi Almanya Türkiye İstanbul Şubesi

Maslak Meydan Sodak, Spring Giz Plaza Bagimsiz Böl.

No:3, Sariyer Istanbul, Turkey

Tel: +90-212-999-8010

CYPRUS

Nakas Music Cyprus Ltd.

Nikis Ave 2k

1086 Nicosia

Tel: + 357-22-511080

Major Music Center

21 Ali Riza Ave. Ortakoy

P.O.Box 475 Nicosia, Cyprus

Tel: (392) 227 9213

OTHER COUNTRIES

Yamaha Music Gulf FZE

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co., Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: +86-400-051-7700

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: +852-2737-7688

INDIA

Yamaha Music India Private Limited

P-401, JMD Megapolis, Sector-48, Sohna Road,

Gurgaon-122018, Haryana, India

Tel: +91-124-485-3300

INDONESIA

PT. Yamaha Musik Indonesia (Distributor)

Yamaha Music Center Bldg. Jalan Jend. Gatot Subroto

Kav. 4, Jakarta 12930, Indonesia

Tel: +62-21-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, Dongsung Bldg. 21, Teheran-ro 87-gil, Gangnam-

gu, Seoul, 06169, Korea

Tel: +82-2-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn. Bhd.

No.8, Jalan Perbandaran, Kelana Jaya, 47301

Petaling Jaya, Selangor, Malaysia

Tel: +60-3-78030900

SINGAPORE

Yamaha Music (Asia) Private Limited

Block 202 Hougang Street 21, #02-00,

Singapore 530202, Singapore

Tel: +65-6740-9200

TAIWAN

Yamaha Music & Electronics Taiwan Co., Ltd.

2F., No.1, Yuandong Rd., Banqiao Dist.,

New Taipei City 22063, Taiwan (R.O.C.)

Tel: +886-2-7741-8888

THAILAND

Siam Music Yamaha Co., Ltd.

3, 4, 15, 16th Fl., Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: +66-2215-2622

VIETNAM

Yamaha Music Vietnam Company Limited

15th Floor, Nam A Bank Tower, 201-203 Cach Mang

Thang Tam St., Ward 4, Dist.3,

Ho Chi Minh City, Vietnam

Tel: +84-8-3818-1122

OTHER ASIAN COUNTRIES

http://asia.yamaha.com

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

VIC 3006, Australia

Tel: +61-3-9693-5111

NEW ZEALAND

Music Works LTD

P.O.BOX 6246 Wellesley, Auckland 4680,

New Zealand

Tel: +64-9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

http://asia.yamaha.com

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

DMI20

Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan

(For European Countries) Importer: Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany

Manual Development Group

Published 06/2017 POHD*.*- **A0

Printed in China

ZW72890

Yamaha EAD10 Drum Module Manual de usuario

Marca: Yamaha

Modelo: EAD10 Drum Module

Categoría: Tambores musicales

Tipo: Manual de usuario

Este manual también es adecuado para

Descargar PDF

informe

En otros idiomas

français: Yamaha EAD10 Drum Module Manuel utilisateur
italiano: Yamaha EAD10 Drum Module Manuale utente
English: Yamaha EAD10 Drum Module User manual
Deutsch: Yamaha EAD10 Drum Module Benutzerhandbuch
русский: Yamaha EAD10 Drum Module Руководство пользователя
Nederlands: Yamaha EAD10 Drum Module Handleiding
português: Yamaha EAD10 Drum Module Manual do usuário
dansk: Yamaha EAD10 Drum Module Brugermanual
polski: Yamaha EAD10 Drum Module Instrukcja obsługi
čeština: Yamaha EAD10 Drum Module Uživatelský manuál
svenska: Yamaha EAD10 Drum Module Användarmanual
Türkçe: Yamaha EAD10 Drum Module Kullanım kılavuzu
suomi: Yamaha EAD10 Drum Module Ohjekirja
română: Yamaha EAD10 Drum Module Manual de utilizare

Yamaha EAD10 Drum Module Manual de usuario

Este manual también es adecuado para

Yamaha EAD10 Drum Module Manual de usuario

En otros idiomas

Documentos relacionados