Transcripción de documentos

■ Handling Precautions RS75 • Do not alter the product. Doing so may result in damage or deterioration to the product. • Do not step on or place heavy objects on the product. It may result in damage. • Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc.) or damp (bathroom, outside on a rainy day, etc.). It may result in deformation, discoloration, stickiness, damage or deterioration. • To clean the product, please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product, it may result in deterioration. ASSEMBLY INSTRUCTIONS INTRODUCTION Thank you for purchasing the Yamaha Electronic Drum Rack System RS75. Before using, thoroughly read these assembly instructions, and use this product safely and correctly. ■ Inside This Package PRECAUTIONS Before using, please read this “Assembly Instruction” sheet, and use this product in a safe and proper manner. Especially for children, parents or an instructor should teach the children the proper manner in which to use the device. Before setup, please make sure that all of the items listed below are present and accounted for. If anything is missing, please contact the dealer from whom you purchased the unit. To prevent against accidents and injury Please follow the cautions listed below Caution (including danger, or warning). This mark indicates cautions in which you should pay close attention to. ◆ Overall Assembly RS75 (When the box is opened) Acts indicated with this icon are prohibited and should not be attempted. WARNING ◆ Small Screws M5 X 8 If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. (Module Holder Fixing Screws X4) Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the instrument being unstable and overturning. Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury. When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop, the rack or pipes may slip, pinching or causing injury to hands or fingers. Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury. Please be careful when children are close to or touching the product. The product has many pipes and arms so careless movement around the product may result in injury. ◆ Cable Band (x10) When setting the pads and modules, please pay close attention in regards to the handling and setting of cables. Feet may become entangled in the cables resulting in falls. If this symbol is ignored and the equipment is used improperly, there is a danger of injury to persons handling the equipment, and material damage could occur. CAUTION Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury. ◆ Assembly Instructions (this sheet) Watch your fingers when adjusting clamps. They may become pinched resulting in injury. Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers. ◆ Rubber Foot (x2) Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. * Specifications are subject to change without notice. ■ RS75 Assembly * Parts for the RS75's main structure have already been assembled before packing. After removing the unit from the box, follow the instructions described below to complete the assembly. A Phillips (+) screwdriver is required when attaching the Drum Trigger Module. Please prepare one before starting assembly. 1 After removing the unit from the box, remove all cushion material. 2 Setting up the parts 3 Attaching the Drum Trigger Module 3-1 • Loosen the wing bolts, slide the pipes out a little, and attach the rubber feet. • Loosen the bolts on the movable arms and legs, as shown in the diagrams below, then secure the bolts firmly once setting is complete. Follow the setup order (q~i) in the diagrams shown below. Caution : Make sure the bolts marked with a " Make sure only the supplied screws are used. Using any other screws may result in the unit falling off the holder or damage. Cymbal Holder 3-2 " are loosened before setting up. Reattach the module holder to the holder clamp. t r Module Holder Assembly Remove the module holder from the holder clamp, and use the supplied screws to attach the Drum Trigger Module. y e Cymbal Holder u i ←Caution Side Arm (R) Assembly Right Leg Assembly ←Caution Rubber Foot Rubber Foot Loosen Side Arm (L) Assembly q w Loosen Loosen Left Leg Assembly Loosen Be careful around the pipe edges. The cut pipe ends are sharp and can injure your fingers.  ■ Optional Parts ■ Set up example ● Pad and Drum Trigger Grouping q DTX Series Drum Trigger Module w TP65/65S Drum Pad e PCY130/130S Cymbal Pad Satellite Speaker r PCY150S Cymbal Pad t RHH130 Real Hi-hat Pad PCY150S PCY130S r e Satellite Speaker y Hi-hat stand *HS740 etc. q PCY130 e u Foot Pedal FP-7210 etc. i KP65 Kick Pad RHH130 t w w w ● Monitor System and Attachment Grouping i TP65S • SPAT1 Speaker Attachment • TPCL65 Tom Holder • MS50DR • Sub Woofer amp unit • CYAT65 Cymbal Attachment • MS100DR • Satellite Speakers • Sub Woofer amp unit • Satellite Speakers u Sub Woofer amp unit y 4 Step 3 Attach the cymbal pads to the cymbal holders and adjust their position, then secure in place. (Please refer to the Owner's Manual that came with the cymbal pads on attaching the cymbal pads.) Step 4 Felt Drum Trigger Module Step 3-1 Attaching the cymbal pads Module Holder Step 3-2 Holder Clamp Cymbal Pad (PCY130/130S/150S) 5 Attaching the drum pads Attach drum pads to the hexagonal rod cylinder and adjust their position, the secure in place. Anti-swivel brace (supplied with the (PCY130/130S/150S) Make sure all bolts on clamps, pads, etc., are firmly tightened. Loose or over-tightened bolts may result in the part falling off and/or damage. Please use caution. After assembly is complete, setup the kick pad, real hi-hat pad, etc., and connect the cables. Use the supplied cable bands to secure the cables to the frame pipes to keep cables out of the way during performance. If the rack is moved even after setup is complete, make sure the bolts are loosened before moving the rack. Step 5 Drum Pad Printed in Indonesia WG24080