Symphonic MSD724F Manual de usuario

Marca: Symphonic

Modelo: MSD724F

Categoría: Reproductores de casete

Tipo: Manual de usuario

Este manual también es adecuado para

COLOR TV/VCR/DVD TRIPLE COMBO

SC724FDF

(24 inch)

OWNER’S

MANUAL

If you need additional operating assistance after reading this owner’s

manual or to order replacement accessories, please call

TOLL FREE : 1-800-242-7158.

Or visit our WEB SITE at http://www.Symphonic.us

Please read before using this equipment

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

1. Read instructions - All the safety and operating instruc-

tions should be read before the appliance is operated.

2. Retain Instructions - The safety and operating instruc-

tions should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in

the operating instructions should be adhered to.

4. Follow Instructions - All operating and use instructions

should be followed.

5. Cleaning - Unplug the unit from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

EXCEPTION: A product that is meant for uninterrupted

service and, that for some specific reason, such as the

possibility of the loss of an authorization code for a

CATV converter, is not intended to be unplugged by the

user for cleaning or any other purpose, may exclude the

reference to unplugging the appliance in the cleaning

description otherwise required in item 5.

6. Attachments - Do not use attachments not recommend-

ed by the unit manufacturer as they may cause hazards.

7. Water and Moisture - Do not use this unit near water-

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub, in a wet basement, or near a swimming

pool, and the like.

8. Accessories - Do not place this unit on an unstable cart,

stand, tripod, bracket, or table. The unit may fall, caus-

ing serious injury to someone, and serious damage to the

appliance. Use only with a cart, stand, tripod, bracket, or

table recommended by the manufacturer, or sold with the

unit. Any mounting of the appli-

ance should follow the manufac-

turer’s instructions and should

use a mounting accessory rec-

ommended by the manufacturer.

An appliance and cart combina-

tion should be moved with care.

Quick stops, excessive force,

and uneven surfaces may cause

the appliance and cart combina-

tion to overturn.

AMEUBLES - Cet appareil ne

doit être placé que sur un meu-

ble (avec ou sans roulettes)

recommandé par le fabricant. Si

vous l’installez sur un meuble à

roulettes, déplacez les deux

ensembles avec précaution. Un

arrêt brusque, l’utilisation d’une

force excessive et des surfaces

irrégulières risquent de déstabiliser l’ensemble et de le

renverser.

9. Ventilation - Slots and openings in the cabinet and the

back or bottom are provided for ventilation and to

ensure reliable operation of the unit and to protect it

from overheating, and these openings must not be

blocked or covered. The openings should never be

blocked by placing the unit on a bed, sofa, rug, or other

similar surface. This unit should never be placed near or

over a radiator or heat register. This unit should not be

placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the manu-

facturer’s instructions have been adhered to.

10. Power Sources - This unit should be operated only from

the type of power source indicated on the marking label.

If you are not sure of the type of power supply to your

home, consult your appliance dealer or local power com-

pany. For the units intended to operate from battery

power, or other sources, refer to the operating instruc-

tions.

11.Grounding or Polarization - This unit is equipped with

a polarized alternating-current line plug(a plug having

one blade wider than the other). This plug will fit into

the power outlet only one way. This is a safety feature. If

you are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, con-

tact your electrician to replace your obsolete outlet. Do

not defeat the safety purpose of the polarized plug.

12. Power-Cord Protection - Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

- 2 - EN

IMPORTANT SAFEGUARDS

PORTABLE CART WARNING

S3126A

SYMBOLE D'AVERTISSEMENT POUR

LES COMPOSANTES

APPAREIL ET MEUBLE A ROULETTES

S3126A

The caution marking is located on the rear of the cabinet.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THIS SYMBOL INDICATES THAT

DANGEROUS VOLTAGE

CONSTITUTING A RISK OF ELECTRIC

SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE

ARE IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS IN THE

LITERATURE ACCOMPANYING THE

APPLIANCE.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

- 3 - EN

13. Outdoor Antenna grounding - If an outside antenna or

cable system is connected to the unit, be sure the anten-

na or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect

to proper grounding of the mast and supporting struc-

ture, grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna-discharge unit, connection to grounding elec-

trodes, and requirements for the grounding electrode.

(Fig. A)

14. Lightning - For added protection for this unit receiver

during a lightning storm, or when it is left unattended

and unused for long periods of time, unplug it from the

wall outlet and disconnect the antenna or cable system.

This will prevent damage to the unit due to lightning and

power-line surges.

15. Power Lines - An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep

from touching such power lines or circuits as contact

with them might be fatal.

16. Overloading - Do not overload wall outlets and exten-

sion cords as this can result in a risk of fire or electric

shock.

17. Object and Liquid Entry - Never push objects of any

kind into this unit through openings as they may touch

dangerous voltage points or short out parts that could

result in a fire or electric shock. Never spill liquid of any

kind on the unit.

18. Servicing - Do not attempt to service this unit yourself

as opening or removing covers may expose you to dan-

gerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19. Damage Requiring Service - Unplug this unit from the

wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or

frayed.

b. If liquid has been spilled, or objects have fallen into the

unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper

adjustment of other controls may result in damage and

will often require extensive work by a qualified techni-

cian to restore the unit to its normal operation.

e. If the unit has been dropped or damaged in any way.

f. When the unit exhibits a distinct change in performance,

this indicates a need for service.

20. Replacement Parts - When replacement parts are

required, be sure the service technician has used replace-

ment parts specified by the manufacturer that have the

same characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, injury to

persons or other hazards.

21. Safety Check - Upon completion of any service or

repairs to this unit, ask the service technician to perform

routine safety checks to determine that the unit is in

proper operating condition.

22. Heat - This unit product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

GROUND CLAMPS

NEC - NATIONAL ELECTRICAL CODE

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

S2898A

WIRE

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

ELECTRODE SYSTEM

(NEC ART 250, PART H)

SERVICE

EQUIPMENT

CLAMP

ANTENNA

L EAD IN

ANTENNA

POWER SERVICE GROUNDING

GROUND

ELECTRIC

FIGURE A

- 4 - EN

The serial number of this product may be found on the back of the unit. No other unit has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

A NOTE ABOUT RECYCLING

Batteries should never be thrown away or inciner-

ated but disposed of in accordance with your local

regulations concerning chemical wastes.

RADIO-TV INTERFERENCE

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This product incorporates copyright protection tech-

nology that is protected by U.S. patents and other

intellectual property rights. Use of this copyright

protection technology must be authorized by

Macrovision, and is intended for home and other

limited viewing uses only unless otherwise autho-

rized by Macrovision. Reverse engineering or dis-

assembly is prohibited.

LASER SAFETY

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est con-

forme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

PRECAUTIONS

- 5 - EN

AV OID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

LOCATION

For safe operation and satisfactory performance of

your unit, keep the following in mind when selecting

a place for its installation:

•

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

Avoid dusty or humid places.

•

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top or bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

•

Install unit in a horizontal position.

•

Avoid locations subject to strong vibration.

•

Do not place the unit near strong magnetic fields.

•

Avoid moving the unit to locations where tempera-

ture differences are extreme.

•

Be sure to remove disc and unplug the AC power

cord from the outlet before carrying the unit.

•

Do not handle the power cord with wet hands.

•

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

•

If by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

Do not put your fingers or objects into the unit disc

loading tray.

•

Do not place anything directly on top of the unit.

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a unit which has

moisture, it may damage the DVD and the unit.

Therefore when the condensation occurs inside the

unit, turn the unit on and allow at least 2 hours for the

unit to dry out.

The following symbols below appear in some head-

ings and notes in this manual, with the following

meanings.

: Description refers to TV/VCR operation (in the

TV/VCR mode).

: Description refers to playback of DVD video discs

(in the DVD mode).

: Description refers to playback of Audio CDs

(in the DVD mode).

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

QUICK

DVD-V

TV/VCR

SYMBOLS USED IN THIS MANUAL

SUPPLIED ACCESSORIES

•

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our

help line mentioned on the front page.

•

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

BatteriesRemote Control Unit

2 AA BatteriesNE209UD

Owner’s Manual

1EMN20315

Owner's Manual

- 6 - EN

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . .2

C PRECAUTIONS . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE .5

WARNING . . . . . . . . . . . . . . . . . . . .5

SYMBOLS USED IN THIS

MANUAL . . . . . . . . . . . . . . . . . . . . .5

C SUPPLIED ACCESSORIES . . . . . . .5

C TABLE OF CONTENTS . . . . . . . . . .6

C FEATURES . . . . . . . . . . . . . . . . . . . .7

C OPERATING CONTROLS AND

FUNCTIONS . . . . . . . . . . . . . . . . . . .9

INSTALLING THE BATTERIES . .11

C PREPARATION FOR USE . . . . . . .12

ANTENNA/CABLE

CONNECTION . . . . . . . . . . . . . . . .12

CONNECTING TO FRONT A/V

INPUT JACKS . . . . . . . . . . . . . . . .13

CONNECTING TO A STEREO

AMPLIFIER EQUIPPED WITH DIGI-

TAL INPUT JACKS (for DVD) . . .13

CONNECTING TO A DOLBY

DIGITAL DECODER (for DVD) . .14

TV/VCR SECTION

C TV OPERATION AND SETTINGS .15

WATCHING A TV PROGRAM . . .15

DEGAUSSING . . . . . . . . . . . . . . . .15

PICTURE CONTROL . . . . . . . . . . .15

SLEEP TIMER . . . . . . . . . . . . . . . .16

CLOSED CAPTION SYSTEM . . . .16

CHANNEL SET UP . . . . . . . . . . . .17

CLOCK SET UP

(AUTO / MANUAL) . . . . . . . . . . . .18

DAYLIGHT-SAVING TIME . . . . . .19

V-CHIP SET UP . . . . . . . . . . . . . . .20

TV RATING SET UP . . . . . . . . .20

MPAA RATING SET UP . . . . . .21

CHANGE ACCESS CODE . . . . .21

MENU LANGUAGE . . . . . . . . . . .21

C MTS (Multi-Channel Television

sound) SYSTEM . . . . . . . . . . . . . . .22

CHECKING THE SELECTED

MTS MODE . . . . . . . . . . . . . . . . . .22

MTS RECORDING/MONITOR

MODE . . . . . . . . . . . . . . . . . . . . . .22

SELECTING THE MTS SYSTEM .23

C VIDEO CASSETTE . . . . . . . . . . . . .24

C PLAYBACK . . . . . . . . . . . . . . . . . . .25

NORMAL PLAYBACK . . . . . . . . .25

TRACKING ADJUSTMENT . . . . .25

SLOW MOTION . . . . . . . . . . . . . .25

STILL PICTURE . . . . . . . . . . . . . .25

VERTICAL HOLD CONTROL . . .25

C SPECIAL PLAYBACK . . . . . . . . . .26

RENTAL PLAYBACK . . . . . . . . . .26

AUTO REPEAT PLAYBACK . . . . .26

C SEARCH . . . . . . . . . . . . . . . . . . . . .27

ZERO RETURN . . . . . . . . . . . . . . .27

PICTURE SEARCH . . . . . . . . . . . .27

TIME SEARCH . . . . . . . . . . . . . . .27

INDEX SEARCH . . . . . . . . . . . . . .28

C SPECIAL FEATURES . . . . . . . . . .28

REAL TIME TAPE COUNTER . . .28

AUTO REWIND-EJECT . . . . . . . .28

C RECORDING . . . . . . . . . . . . . . . . .29

NORMAL RECORDING . . . . . . . .29

SKIPPING UNWANTED SCENES

DURING RECORDING . . . . . . . . .29

OTR (One Touch Recording) . . . . . .30

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder) . . .30

C TIMER RECORDING . . . . . . . . . . .31

AUTOMATIC

TIMER RECORDING . . . . . . . . . .31

AUTO RETURN . . . . . . . . . . . . . . .33

C ON SCREEN DISPLAY . . . . . . . . .34

C CABLE CHANNEL

DESIGNATIONS . . . . . . . . . . . . . .34

DVD SECTION

C ABOUT THE DISCS . . . . . . . . . . . .35

PLAYABLE DISCS . . . . . . . . . . . .35

UNPLAYABLE DISCS . . . . . . . . . .35

C PLAYING A DISC . . . . . . . . . . . . . .36

BASIC PLAYBACK . . . . . . . . . . . .36

GENERAL FEATURES . . . . . . . . .36

DISC MENU . . . . . . . . . . . . . . . . .36

TITLE MENU . . . . . . . . . . . . . . . . .36

RESUME . . . . . . . . . . . . . . . . . . . .37

PAUSE . . . . . . . . . . . . . . . . . . . . . .37

STEP BY STEP PLAYBACK . . . . .37

FAST FORWARD /

FAST REVERSE . . . . . . . . . . . . . .37

SLOW FORWARD /

SLOW REVERSE . . . . . . . . . . . . . .37

ZOOM . . . . . . . . . . . . . . . . . . . . . .37

C SEARCH FUNCTION . . . . . . . . . . .38

TRACK SEARCH . . . . . . . . . . . . .38

TITLE / CHAPTER SEARCH . . . .38

TIME SEARCH . . . . . . . . . . . . . . .38

MARKER SETUP SCREEN . . . . . .38

SPECIAL PLAYBACK FUNCTION . . .39

REPEAT . . . . . . . . . . . . . . . . . . . . .39

PROGRAM . . . . . . . . . . . . . . . . . . .39

RANDOM PLAYBACK . . . . . . . . .39

C CHANGING THE SETTINGS . . . .40

SUBTITLE LANGUAGE . . . . . . . .40

AUDIO LANGUAGE . . . . . . . . . . .40

STEREO SOUND MODE . . . . . . . .40

CAMERA ANGLE . . . . . . . . . . . . .41

BLACK LEVEL SETTING . . . . . . .41

VIRTUAL SURROUND . . . . . . . . .41

THE ON-SCREEN INFORMATION

. .42

C CHANGING THE DVD SET UP

ITEMS . . . . . . . . . . . . . . . . . . . . . . .43

CUSTOM MENU . . . . . . . . . . . . . .43

LANGUAGE SETTING . . . . . . .43

DISPLAY SETTING . . . . . . . . . .44

AUDIO SETTING . . . . . . . . . . .44

PARENTAL CONTROL . . . . . . .45

OTHER SETTINGS . . . . . . . . . .45

INITIALIZE . . . . . . . . . . . . . . . . . .45

C TROUBLESHOOTING GUIDE . . .46

C MAINTENANCE . . . . . . . . . . . . . . .49

DISC HANDLING . . . . . . . . . . . . .49

C SPECIFICATIONS . . . . . . . . . . . . .50

C ESPAÑOL . . . . . . . . . . . . . . . . . . . .51

C WARRANTY . . . . . . . . . . .Back Cover

- 7 - EN

•

Hi-Fi system – The Hi-Fi stereo recording system

offers you excellent sound quality with a dynamic

range of 80dB, frequency response from 20Hz to

20kHz and 0.005% wow and flutter.

•

Rotary 4-head Record/Playback System – Four

heads ensure excellent picture quality and special

effects playback.

•

Index Search –

Fast-forwards to start of next record-

ing.

•

Slow Motion – View recorded program at slower

than normal speed.

•

Infrared remote control

•

Trilingual on screen TV/VCR setup display

selectable in English, Spanish or French

•

Real time counter – This shows the elapsed record-

ing or playback time in hours, minutes and seconds.

The

“–” indication will appear when the tape is

rewound

further than the tape counter position

“0:00:00”.

•

181 channel capability PLL frequency synthesiz-

er tuner with direct station call

(A converter may

be necessary to view scrambled cable channels.)

•

Auto Clock Setting – Allows you to set the clock

function from a PBS broadcast station.

•

Closed Caption Decoder – You may view special-

ly labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

•

Auto power on and off system – Automatically

turns on the unit when you insert the cassette, turns

off after auto-rewind and ejects when the begin-

ning of the tape is reached.

•

Auto rewind when the end of a tape is reached

(This function doesn’t occur when using timer

recording.)

•

Smooth mode change – TV/VCR mode and DVD

mode automatically changes without control.

•

2 Step picture search operation – You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode, only high speed is avail-

able.

•

Three different playback tape speeds : SP/LP/SLP

•

Two different recording tape speeds : SP/SLP

•

Auto Head Cleaner – Automatically cleans video

heads as you insert or remove a cassette.

•

Zero Return – The tape returns to counter of

0:00:00 by rewinding or fast forwarding.

•

Still – “Freeze” the picture at any time, for close

viewing of a particular scene.

•

Digital Auto Tracking (DTR) – Automatically

adjusts the tracking for each tape you play.

•

Rental play mode – Improves playback picture

quality from worn tapes, such as rental tapes.

•

Auto repeat – Allows you to repeat the playing of

a tape indefinitely without hitting [PLAY O].

•

Time search – Lets you set the unit to advance the

tape by entering the desired playback time you want

to skip.

•

OTR (One Touch Recording) – Instant timed

recording from 30 to 480 minutes is possible by

hitting [REC/OTR].

•

1 Year, 8 events (including Daily and Weekly)

Timer Recording –

The built-in timer allows you

to record up to 8 programs at different times on

different channels up to 1 year in advance. The

Daily timer allows recordings to be made of daily

broadcasts and the Weekly timer allows recording

to be made once a week up to the end of the tape.

•

Auto return – After timer recording is finished, the

unit can return to the beginning of the recording.

•

Sleep timer – Allows you to have the unit auto-

matically turn off at a desired time.

•

Timer Program Extension – Allows you to shift

the time schedule for automatic timer recording.

•

V-CHIP – Enables parents to prevent their children

from watching inappropriate material on TV.

FEATURES

TV/VCR Mode

- 8 - EN

¡On-screen display

Information about the current operation can be dis-

played on a TV screen, allowing you to confirm the

currently active functions (such as program play-

back), on the TV screen using the remote control.

¡Search

Chapter search / Title search / Track search / Time

¡Repeat

Chapter / Title / Track / All / A-B

¡Zoom

Magnified screen can be displayed.

¡Marker

The part designated by user can be called back.

¡Resume Play

User can resume to playback from the part at which

the play was stopped.

¡Virtual Surround

¡Bit rate indication

¡DRC (Dynamic range control)

You can control the range of sound volume.

DVD Mode

¡Dolby Digital sound

This unit can handle Dolby Digital surround sound

having 5.1 channels when connected to a Dolby

Digital decoder.

¡Still/fast/slow/step playback

Various playback modes are available including still

pictures, fast forward/reverse, slow motion and step

frames.

¡Random playback for Audio CD

This unit can shuffle the order of tracks to play them

in random order.

¡Program playback for Audio CD

You can program the order of tracks to play them in

any desired order.

¡DVD menus in a desired language

You can display DVD menus in a desired language,

if available on a DVD.

¡Screen saver/Auto power-off functions

The screen saver program starts when there is no

input from the unit for 5 minutes in the stop mode.

After the screen saver program is activated for 15

minutes, the power automatically turns off.

¡Subtitles in a desired language

You can select a desired language for the display

subtitles, if that language is available on a disc.

¡Selecting a camera angle

You can select the desired camera angle, if a disc

contains sequences recorded from different angles.

¡Choices for audio language and sound mode

You can select the desired audio language and sound

mode, if different languages and modes are available

on a disc.

¡Parental lock

You can set the control level to limit playback of

discs which may not be suitable for children.

¡Automatic detection of discs

This unit automatically detects if the loaded disc is

DVD or Audio CD.

- 9 - EN

OPERATING CONTROLS AND FUNCTIONS

5.C STOP Button

[TV/VCR P.25 / DVD P.37]

(Front panel) Stops operation of the disc.

(Remote control) Stops operation of the disc or

tape contents.

6.A OPEN/CLOSE Button

[DVD P.36]

Hit to insert a disc into or remove it from the tray.

7.Disc loading tray

8.DVD Indicator

Lights up during DVD mode.

9.SELECT Button

[TV/VCR P.15] [DVD P.36]

Hit to change to TV/VCR mode, external input

mode or DVD mode. You can see the mode

(TV/VCR or DVD) on the front panel indicator.

10.TV/VCR Indicator

Lights up during TV/VCR mode.

11. CHANNEL (CH.) K / L Buttons

Press to select memorized channels.

12. Recording Indicator

Flashes during recording. Lights up in the stand-

by mode for Timer Recording.

13. REC/OTR Button (Front Panel)

[TV/VCR P.30]

Hit to start manual recording. Hit repeatedly to

start One Touch Recording.

RECORD Button (Remote Control)

[TV/VCR P.29]

Hit to start manual recording.

14. E REW Button (for TV/VCR)

[TV/VCR P.27]

Hit to rewind the tape or to view the picture rapid-

ly in reverse during playback mode. (Rewind

Search)

15. F.FWD D Button (for TV/VCR)

[TV/VCR P.27]

Hit to rapidly advance the tape or to view the pic-

ture rapidly in forward during playback mode.

(Forward Search)

16. C / A STOP/EJECT Button

[TV/VCR P.24, 27]

Hit to stop the tape motion. Hit in the stop mode

to remove tape from the unit.

17. Remote sensor window

18. HEADPHONE Jack

To connect headphone (not supplied) for personal

listening.

- REMOTE CONTROL -

[Fig. 2]

1.POWER Button

[TV/VCR P.15 / DVD P.36]

Hit to turn the power on and off.

2.VOLUME (VOL.) K / L Buttons

Press to control the volume level for the DVD and TV.

3.SKIP H / G Buttons (for DVD)

[DVD P.38]

Press once to skip chapters or tracks to a desired

point.

SEARCH h / g Buttons (for DVD)

[DVD P.37]

Press and hold to change forward or reverse play-

back speed.

4.B PLAY Button

[TV/VCR P.25 / DVD P.36]

Starts playback of the disc or tape contents.

- FRONT PANEL - [Fig.1]

POWER

VOLUME

CHANNEL

REC/OTR

–

SKIP SKIP

PLAY

STOP

OPEN/CLOSE

REW F.FWD

PLAY

STOP

HEADPHONE

VIDEO

–

AUDIO

–

EJECT

DVD

TV/VCR

SELECT

5 6 10

983 3 411 12 13 2120191817162

DVD buttons TV/VCR buttons

PAUSE

PLAY

STOP

ENTER

RECORD

DISC

RETURNTITLESETUP

REPEATSEARCH MODE

CLEAR

MODE

ANGLESUBTITLEAUDIO

DISPLAY

SPEED C.RESET

POWER PICTURE SELECTSLEEP

CH.

VOL.

MUTEZOOM

123

456

789

0 +10

+100

(DVD) 3

(TV/VCR) 14

3 (DVD)

15 (TV/VCR)

- 10 - EN

ANT.

AUDIO OUT

COAXIAL

19. VIDEO input Jack

Connect to the video output jack of a video

camera or VCR.

20. AUDIO L/R input Jacks

Connect to the audio output jacks of a video

camera or VCR.

21. Cassette compartment

22. PICTURE Button

Hit to adjust the picture.

23. Number Buttons

TV/VCR Mode:

[P.17]

Press two digits to directly access the desired

channel.

Remember to hit [0] before a single digit channel.

+100 Button–

Hit to select cable channels which are higher than

99.

DVD Mode:

[P.38]

Hit to enter the desired number.

+10 Button–

Hit to enter the desired numbers which are higher

than 9.

24. PAUSE F Button

[TV/VCR P.25 / DVD P.37]

Pauses the current disc or tape operation.

25. SPEED Button

[TV/VCR P.29]

Hit to choose the desired recording speed:

SP/SLP.

26. C.RESET Button

[TV/VCR P.27]

Hit to reset counter to “0:00:00”.

Hit to cancel a setting of timer program. (Refer to

page 32.)

27. DISPLAY Button

TV/VCR Mode:

[P.22]

Displays the counter or the current channel num-

ber and current time on the TV screen.

DVD Mode:

[P.42]

Displays the current status on the TV screen.

28. SETUP Button

[TV/VCR P.16] [DVD P.43-45]

Hit to enter or exit the setup menu of TV or DVD.

29. TITLE Button

[DVD P.36]

Displays the title menu.

30. CLEAR Button

[DVD P.38]

Hit to clear or cancel a setting currently entered.

31. MODE Button

[DVD P.39, 41]

Hit to call up the program screen or the random

screen in the stop mode.

Hit to call up the Black Level Setting screen or

the Virtual Surround screen during playback.

32. SEARCH MODE Button

[DVD P.38]

Hit to locate a desired point.

33. AUDIO Button

TV/VCR Mode:

[P.23]

Hit to select a desired sound mode when watching

a TV program or playing or recording a cassette

tape.

DVD Mode:

[P.40]

Hit to select a desired audio language or sound

mode.

34. SUBTITLE Button

[DVD P.40]

Hit to select a desired subtitle language.

35. REPEAT Button

[DVD P.39]

Repeats playback of the current disc, title, chapter,

or track.

36. ANGLE Button

[DVD P.41]

Hit to change the camera angle to see the sequence

being played back from a different angle (if avail-

able).

37. A-B Button

[DVD P.39]

Repeats playback of a selected section.

38. RETURN Button

[TV/VCR P.32] [DVD P.38]

Returns to the previous screen in the setup menu.

39. ENTER Button

[TV/VCR P.16] [DVD P.36]

Hit to accept a setting.

40. K / L / { / B Buttons

TV/VCR Mode:

[P.15]

Press to select a setting mode from the menu on

the TV screen.

Press to select or adjust from a particular menu.

DVD Mode:

[P.36]

Press to select a menu item.

41. DISC MENU Button

[DVD P.36]

Calls up the DVD menu.

42. ZOOM Button

[DVD P.37]

Enlarges part of a DVD-reproduced image.

- REAR PANEL - [Fig.3]

- 11 - EN

43. MUTE Button

[TV/VCR P.15]

Mutes the sound. Hit it again to restore sound.

44. SLEEP Button

[TV/VCR P.16]

Sets the Sleep Timer.

45. ANT(ENNA). Jack

[P.12]

Connect to an antenna, cable system or satellite

system.

46. Power cord

[P.15]

Connect to a standard AC outlet (120V/60Hz).

NOTE:

•

Remove the power cord from the hook to

avoid breaking a wire before you connect to a

standard AC outlet.

47. AUDIO OUT COAXIAL Jack

[P.13]

Connect to the digital input of an external

amplifier or decoder (for DVD Audio only).

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

3)Replace the cover.

[BATTERY PRECAUTIONS]

•

Be sure to follow the correct polarity as indicated

in the battery compartment. Reversed batteries

may cause damage to the device.

•

Do not mix different types of batteries together

(e.g. Alkaline and Carbon-Zinc) or old batteries

with fresh ones.

•

If the device is not to be used for a long period of

time, remove the batteries to prevent damage or

injury from possible battery leakage.

•

Do not try to recharge batteries not intended to be

recharged; they can overheat and rupture.

NOTE:

•

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

NOTE:

•

Before plugging the antenna into the ANT. jack of the unit, check that the pin is

not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the

ANT. jack of the unit.

- 12 - EN

CABLE WITH CONVERTER/DESCRAM-

BLER BOX OR SATELLITE BOX

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown above.

Channel selection must be made with the converter

box or satellite box. This means that channels cannot

be changed using the remote control of this unit.

PREPARATION FOR USE

VHF/UHF COMBINED ANTENNA

A VHF UHF 75 ohm combination antenna can be

connected to ANT. jack of the unit.

VHF/UHF SEPARATE ANTENNAS

In some areas it will be necessary to use an outdoor

antenna.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to the unit without a converter box.

ANT.

AUDIO OUT

COAXIAL

UHF

VHF

VHF/UHF

OUT IN

VHF

UHF

VHF

UHF

VHF/UHF

Combiner

Flat twin-

lead cable

From Cable System

75-ohm

Coaxial Cable

CATV Box or

Satellite Box *

From Cable System or

Satellite Antenna

[Fig. 4]

ANTENNA/CABLE CONNECTION

Bent pin

Cable

Plug

(Needs to be

straightened)

(Straight pin)

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding

system of the building as close to the point of cable entry as practical.

[ANTENNA CONNECTION]

[CATV/SATELLITE CONNECTION]

*Some cable TV systems use scrambled signals and

require a special converter to receive these channels.

Consult your local cable company.

Adaptor

75-ohm

Coaxial Cable

NOTE:

•

For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack

before moving the unit.

Cables used here are commercially available.

CONNECTING TO FRONT A/V INPUT JACKS

When you watch a program recorded on another source (VCR or video camera), use the

AUDIO/VIDEO input jacks on the front of the unit.

Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO

jacks of this unit.

Then press [SELECT] or [CH.

] until “AUX” appears on the screen.

- 13 - EN

CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH

DIGITAL INPUT JACKS (for DVD)

Use an audio coaxial digital cable (commercially available) for the audio connections.

Connect to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.

NOTES:

•

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

•

Refer to the Owner’s Manuals for the components to be connected to the unit.

•

Set “DOLBY DIGITAL” to “PCM” for audio output in the setup mode. Playing a unit using incorrect set-

tings may generate noise distortion and may also damage the speakers. (Refer to page 44.)

ANT.

AUDIO OUT

COAXIAL

ex.

MD deck, DAT deck, etc.

To Coaxial digital

Audio input jack

Audio coaxial digital cable

(commercially available)

To AUDIO OUT

COAXIAL jack

(Only DVD AUDIO OUT)

[Fig. 6]

POWER

VOLUME

CHANNEL

REC/OTR

–

SKIP SKIP

PLAY

STOP

OPEN/CLOSE

REW F.FWD

PLAY

STOP

HEADPHONE

VIDEO

–

AUDIO

–

EJECT

DVD

TV/VCR

SELECT

HEADPHONE

VIDEO

–

AUDIO

–

ex.

VCR or video camera

, etc.

[Front of the unit]

[Fig. 5]

Audio Cable

(commercially available)

To the Audio output jacks

To the Video output jack

Video Cable

(commercially available)

NOTE:

•

When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the

monaural VCR (another source) to the AUDIO L jack of this unit. The audio will output in both L and R

channel equally.

AUX

(OUT)

(IN)

(OUT)

(IN)

(OUT)

(IN)

- 14 - EN

ANT.

AUDIO OUT

COAXIAL

Front speaker

(left)

Center

speaker

Front speaker

(right)

Surround

speaker

(left)

Surround

speaker

(right)

Subwoofer

To AUDIO OUT

COAXIAL jack

(Only DVD AUDIO OUT)

To Coaxial digital

Audio input jack

Dolby Digital

decoder

Audio coaxial digital cable

(commercially available)

[Fig. 7]

CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)

If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a

DOLBY DIGITAL Data stream from its AUDIO OUT COAXIAL jack. By hooking the unit up to a Dolby

Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround

sound as enjoyed in movie theaters.

Use audio coaxial digital cables (commercially available) for the audio connections.

NOTES:

•

Be sure to turn off the power to all components in the system before connecting another component.

•

Refer to the Owner’s Manuals for the components to be connected to the unit.

•

If connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “BITSTREAM” for audio output in the

setup mode. (Refer to page 44.)

•

Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “PCM” for audio output in the

setup mode. Playing a unit using incorrect settings may generate noise distortion and may also damage the

speakers. (Refer to page 44.)

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

(OUT)

(IN)

- 15 - EN

TV/VCR SECTION

TV OPERATION AND SETTINGS

DEGAUSSING

This television has a degaussing circuit that will clear

up color errors on the TV screen that are caused by

any excess magnetism which happens to get too close

to the TV. This circuit is designed to operate once

when the set is first plugged in. If minor color

errors are seen in some locations on the screen,

please unplug the TV for approximately 30 min-

utes. When the TV is plugged back in, the degauss-

ing circuit will operate once to clear them up. Repeat

this procedure any time the TV screen is accidentally

magnetized or when the TV is moved or relocated.

TV/VCR

WATCHING A TV PROGRAM

1 Plug in the unit power cord

Plug the unit power cord into a standard

AC outlet.

NOTE:

•

If any digits appear in the corner of the

screen, hit [POWER] without unplug-

ging the power cord.

2 Turn on the unit

Hit [POWER] to turn on the unit.

3 Select the channel number

Press [CH. K / L] or the Number buttons to select

your desired channel number.

Notes for using the Number buttons:

¡You must precede single-digit channel numbers

with a zero (for example: 02, 03, 04 and so on).

¡When selecting cable channels which are higher

than 99, hit [+100] first, then press the last two

digits. (Example: to select channel 125, first hit

[+100] then hit [2] and [5].)

4 Adjust sound

Press [VOL.

] to adjust the

volume.

Hit

[MUTE] to instantly mute the

sound.

Hit it again to restore the previous sound level.

NOTE:

•

If you press [CH. K / L] in the DVD mode, you

can change the TV channels. Even if you turn off

the unit in the DVD mode, when you turn it on

again, it will go into the TV/VCR mode.

TO WATCH CABLE OR SATELLITE

CHANNEL

•

If the unit is connected to a cable box or satellite

box, press

[CH. K / L] to select CH3 or CH4

according to the output channel setting of the

device, and select desired channel on that device.

TO WATCH EXTERNAL INPUT

•

When an external equipment is connected to the

front AUDIO/VIDEO input jacks, press

[SELECT] or [CH. K / L] repeatedly until

“AUX” appears on the screen.

TV/VCR

BRIGHT to decrease to increase

brightness brightness

CONTRAST to decrease to increase

contrast contrast

COLOR to pale to brilliant

TINT to purple to green

SHARPNESS to soft to clear

PICTURE CONTROL

The unit’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a more natural looking image.

Make sure ...

•

The unit must be turned on.

1 Call up the menu

Hit [PICTURE].

2 Select item you want to adjust

Press [K / L] until desired control is displayed.

BRIGHT

CONTRAST

COLOR

TINT

SHARPNESS

3 Adjust the setting

Press

[

]

to adjust to your desired level within 5

seconds.

TV/VCR

•

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

BRIGHT

–

PP PP PP PP PP PP PP CC PP PP PP PP PP PP PP

VOLUME 20

C C C C C C C C C C C C C C C C

- 16 - EN

•

If the unit displays a black box

on the TV screen, this means that

the unit is set to the TEXT mode.

To clear screen, select [CAP-

TION1], [CAPTION2] or [OFF].

Make sure ...

•

The unit must be turned on.

1 Select “CAPTION”

Hit [SETUP].

Press

[K / L]

to point to “CAP-

TION”.

2 Select your desired caption mode

Hit [ENTER] repeatedly until your

desired caption menu appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

3 Exit the caption setting mode

Hit [SETUP] to exit the menu.

NOTE:

•

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps 1 to 2 and select [OFF] using

[ENTER]. Then hit [SETUP] to return to TV mode.

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news and pre-recorded tapes with either a

dialogue caption or text display.

CAPTION mode: You can watch dramas, movies and

news while captioning the dialogues and the contents

of news.

TEXT mode: You can watch half screen text informa-

tion if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is

usually used for a second language if available.

NOTES:

•

Not all programs are broadcast with closed cap-

tions. Your unit is designed to provide error free

closed captions from high quality antenna, cable

and VCR signals. Conversely, poor quality signals

are likely to result in caption errors or no captions

at all. Common signal conditions which may cause

caption errors are listed below:

•

Automobile ignition noise

•

Electric motor brush noise

•

Weak snowy reception on TV screen

•

Multiplex signal reception displaying picture

ghosts or airplane flutter.

•

Playback of poorly recorded or worn VCR tapes.

TV/VCR

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

B CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

B CAPTION [CAPTION1]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

SLEEP TIMER

The Sleep Timer function turns off the unit without

using [POWER] after a desired period of time.

NOTE:

•

This function does not work during the record-

ing mode.

1 Call up the Sleep Timer Setting

Hit [SLEEP] so that “SLEEP 0 MINUTE” appears.

2 Set sleep time

Hit [SLEEP] repeatedly until your

desired sleep time appears.

Each additional press will increase

the time by 30 minutes up to 120

minutes.

After 5 seconds, the Sleep Timer setting will disap-

pear automatically.

TO CANCEL THE SLEEP TIMER

Hit [SLEEP] to call up the Sleep Timer Setting. Hit

[SLEEP] repeatedly until “SLEEP 0 MINUTE”

appears.

TV/VCR

SLEEP 120 MINUTE

- 17 - EN

CHANNEL SET UP

Make sure ...

•

The unit must be turned on.

AUTO CHANNEL PROGRAMMING

As the initial setting, this unit has memorized all

channels, including the ones not available in your

area. This feature automatically puts only available

channels into the memory.

1 Select “CHANNEL SET UP”

Hit [SETUP].

Press

[K / L]

to point to

“CHANNEL SET UP”, then hit

[ENTER].

2 Begin channel scanning

Press

[K / L]

to point to “AUTO

CH PROGRAMMING”, then hit

[ENTER].

The tuner scans and memorizes all

the active channels in your area.

3 After scanning

The tuner stops on the lowest memorized channel.

NOTES:

•

When “AUTO CH PROGRAM-

MING” is activated where there

is no TV signal input, “NO TV

SIGNALS” will appear on the

display after the completion of

channel scanning.

•

The unit may recognize CATV channels to be TV

channels if reception condition is poor. In this case,

check the antenna connection and try “AUTO CH

PROGRAMMING” again when reception condi-

tions are better.

•

Channel memory programming is NOT neces-

sary when connected to a cable box or satellite

box. Just select the channel for cable box or

satellite input (ex. CH3) on the unit, then select

your desired channel on the cable box or satel-

lite box.

– CHANNEL SET UP –

ADD / DELETE CH (CATV)

B AUTO CH PROGRAMMING

ADDING/DELETING CHANNELS

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

1 Select “CHANNEL SET UP”

Hit [SETUP].

Press

[K / L]

to point to “CHAN-

NEL SET UP”, then hit [ENTER].

2 Select “ADD/DELETE CH”

Press

[K / L]

to point to

“ADD/DELETE CH”, then hit

[ENTER].

3 Enter the desired channel number

Press [CH. K / L] or the Number

buttons until your desired channel

number appears. (You can also

press [K / L] to enter it.)

•

You must precede single-digit

channel numbers with a zero

(Example: 02 ... 09).

•

When selecting cable channels which are higher

than 99, hit [+100] first, then press the last two

digits. (Example: to select channel 125, first hit

[+100] then hit [2] and [5].)

4 Delete (or add) it from (or into) memory

Hit [ENTER]. The channel number changes to light

red. The channel is deleted from memory.

•

To delete another channel, repeat steps 3 to 4.

•

If you hit [ENTER] again, the channel is memo-

rized again.

5 Exit the channel setup mode

Hit [SETUP] to exit the menu.

NOTE:

•

To confirm that channel(s) has been deleted or

added, press [CH. K / L].

Added channel : Light blue

Deleted channel : Light red

– CHANNEL SET UP –

B ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

ADD / DELETE

TV/VCR

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

B CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

B CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

(Example: CH8)

NO TV SIGNALS

- 18 - EN

5 Select the year

Press [K / L] until your desired

year appears.

(Example: “2005”)

Then hit

[B].

6 Select the hour

Press [K / L] until your desired

hour appears.

(Example: “5”, “PM”)

Then hit

[B].

7 Select the minute

Press [K / L] until the

desired minute appears.

(Example: “40”)

8 Start the clock

Hit [SETUP].

Although seconds are not displayed,

they begin counting from 00 when

you hit

[SETUP]. Use this feature

to synchronize the clock with the

correct time.

NOTE:

•

When unplugging the AC cord or if there is a

power failure for more than 3 seconds, you may

have to reset the clock.

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps

1 to 2.

2)Select the item you want to change using

[B] .

3)Enter correct numbers using

[K / L].

4)Hit

[SETUP] to start the clock.

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / 0 6 FRI 2 0 0 5

HOUR MINUTE

0 5 : – – PM

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / 0 6 FRI 2 0 0 5

HOUR MINUTE

0 5 : 4 0 PM

5:40 PM

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / 0 6 FRI 2 0 0 5

HOUR MINUTE

– – : – – – –

The unit clock must be set correctly so that VCR

timer recording is possible. It is suggested that the

clock be set manually when first setting up the unit,

then set to [ON] the auto clock setting which will

periodically correct the setting if necessary.

NOTE:

•

If you cannot receive a station with time signals,

auto clock setting cannot be performed. Use manu-

al setting only.

MANUAL CLOCK SETTING

Make sure ...

•

The unit must be turned on.

In the example below, the clock is to be set to:

DATE May 6th, 2005

SETTING TIME 5:40PM

1 Select “SETTING CLOCK”

Hit [SETUP].

Press

[K / L]

to point to “SET-

TING CLOCK”, then hit

[ENTER].

2 Select “MANUAL CLOCK SET”

Press

[K / L]

to point to “MANU-

AL CLOCK SET”, then hit

[ENTER].

•

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and hit

[ENTER] to turn [OFF] this function before this

step.

3 Select the month

Press

[K / L]

until your desired

month appears.

(Example: May

→ “05”)

Then hit

[B]. (Or hit [s] to go

back one step.)

4 Select the day

Press

[K / L]

until your desired day

appears.

(Example: 6th

→ “06”)

Then hit

[B].

CLOCK SET UP

(AUTO / MANUAL)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / – – – – – – – – –

HOUR MINUTE

– – : – – – –

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / 0 6 – – – – – – –

HOUR MINUTE

– – : – – – –

– SETTING CLOCK –

AUTO CLOCK [ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH [ 02 ]

B MANUAL CLOCK SET

D.S.T. [OFF]

TV/VCR

- TV/VCR SETUP -

TIMER PROGRAMMING

B SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

- 19 - EN

DAYLIGHT-SAVING TIME

Select this feature and the unit’s clock automatically

will advance one hour in April, then reverse one hour

in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

•

First Sunday of April : At 2 AM the clock immedi-

ately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM will

not record.

•

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

Make sure ...

•

The unit must be turned on.

1 Select “SETTING CLOCK”

Hit [SETUP].

Press

[K / L] to point to “SET-

TING CLOCK”, then hit [ENTER].

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press [K / L] to point to “D.S.T.”,

then hit [ENTER] until [ON]

appears.

3 Exit the Daylight-Saving Time mode

Hit [SETUP] to exit the menu.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps 1 to 2 and select [OFF] using

[ENTER].

– SETTING CLOCK –

AUTO CLOCK [ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH [ 02 ]

MANUAL CLOCK SET

B D.S.T. [ON]

4 Enter the channel number that contains the

Automatic Clock Setting Signal

Hit [RETURN] to go back to “SETTING CLOCK”

menu.

Hit

[L] to select “AUTO CLOCK

CH”.

Press

[s / B] until you locate Auto

Clock Set station number.

5 Exit the setting clock mode

Hit [SETUP] to exit the menu.

NOTE:

•

Once the unit is turned off, it will periodically

check and set the correct date and time.

– SETTING CLOCK –

AUTO CLOCK [ON]

AUTO CLOCK CH SEARCH

B AUTO CLOCK CH [ 45]

MANUAL CLOCK SET

D.S.T. [OFF]

TV/VCR

- TV/VCR SETUP -

TIMER PROGRAMMING

B SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

AUTOMATIC CLOCK SETTING

Make sure ...

•

The unit must be turned on.

•

Confirm the unit is receiving a RF (Radio

Frequency) signal from either an antenna or cable

system connection using the ANT. jack on the rear

of the unit.

NOTES:

•

If a cable converter box is being used, make sure it

is powered on.

•

You must use the remote control to perform the

clock setting procedure.

•

If the unit is connected directly to a cable converter

box or satellite box, the local PBS station must be

selected on the cable box itself and the unit must be

set to the output channel of the cable converter box

or satellite box (usually channel 3 or 4), to be able

to set up or correct the clock automatically.

1 Select “SETTING CLOCK”

Hit [SETUP].

Press [K / L] to select

“SETTING CLOCK”, then hit

[ENTER] .

2 Set “AUTO CLOCK” to [ON]

Hit [ENTER] to select [ON].

3 Begin “AUTO CLOCK CH SEARCH”

Hit [L] to select “AUTO CLOCK

CH SEARCH”.

Then hit [ENTER].

•

The unit begins searching for the

station which contains the auto

clock set signal. The search for a

signal may take up to 20 seconds per channel.

•

When the search has ended, “_ _”

appears at the lower left of the

screen.

•

Write down the number(s) that

appear on the screen. They are the

auto clock station(s) in your area.

•

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 18.

NOTE:

•

During AUTO CLOCK CH SEARCH, the picture

may be distorted.

– SETTING CLOCK –

B AUTO CLOCK [ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH [ 02 ]

MANUAL CLOCK SET

D.S.T. [OFF]

– SETTING CLOCK –

AUTO CLOCK [ON]

B AUTO CLOCK CH SEARCH

AUTO CLOCK CH [ 02 ]

MANUAL CLOCK SET

D.S.T. [OFF]

– AUTO CLOCK CH SEARCH –

08 10 13

_ _

- TV/VCR SETUP -

TIMER PROGRAMMING

B SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

This feature enables parents to prevent their children

from watching inappropriate material on TV. When

you try to access a program which is blocked,

“PROTECTED PROGRAM by ...” message appears

on the TV screen.

V-CHIP SET UP

Make sure ...

•

The unit must be turned on.

1 Select “V-CHIP SET UP”

Hit [SETUP].

Press

[K / L] to select “V-CHIP

SET UP”, then hit [ENTER].

2 Enter Access code

Press the Number buttons to

enter the access code.

•

For the first time set-up or in the

event the unit has lost power,

enter the default code of 0000.

3 Select the desired item

Press [K / L] to select “TV RATING”, “MPAA RAT-

ING” or “CHANGE CODE”, then hit [ENTER].

Refer to the pages below to set up each item.

TV RATING SET UP

Follow steps

in the “V-CHIP SET UP” sec-

tion above.

4 Blocking TV programs

Press [K / L] to select a rating that

you wish to block.

Hit

[ENTER] repeatedly to set it to

[BLOCK] or [VIEW].

TV/VCR

- 20 - EN

V-CHIP SET UP

B TV–Y [VIEW]

TV–Y7 ( ) [VIEW]

TV–G [VIEW]

TV–PG ( ) [VIEW]

TV–14 ( ) [VIEW]

TV–MA ( ) [VIEW]

Selection Rating Category Explanations

TV-Y Appropriate for all children

TV-Y7 Appropriate for children seven and older

TV-G General Audience

TV-PG Parental Guidance suggested.

TV-14 Unsuitable for children under 14

TV-MA Mature audience only

NOTES:

•

When you select a rating and set

it to [BLOCK], the higher ratings

will be blocked automatically.

The lower ratings will be avail-

able for viewing.

•

When you set the lowest rating to

[VIEW], all other ratings will automatically be

available for viewing.

5 Setting “Sub-Ratings”

When you select the ratings of TV-

Y7, TV-PG, TV-14 or TV-MA you

will have the option of setting sub

rating categories.

Press

[K / L] to select a rating with

sub-ratings you wish to block, then

hit [ENTER] twice.

Press

[K / L] to select a sub-rating,

then hit [ENTER] to set it to

[BLOCK] or [VIEW].

NOTE:

•

The blocked sub-ratings will

appear next to the rating category

in the “TV RATING” menu.

6 Exit the V-Chip setting mode

Hit [SETUP] to exit the menu.

NOTE:

•

To change the rating, the TV must

be turned to an unprotected pro-

gram. If “PROTECTED PRO-

GRAM by ...” appears on the

screen, please change the channel

to a station that is not protected.

TV–Y [VIEW]

TV–Y7 ( ) [VIEW]

TV–G [VIEW]

B TV–PG (DLSV ) [BLOCK]

TV–14 (DLSV) [BLOCK]

TV–MA ( LSV) [BLOCK]

TV–Y7 [BLOCK]

B FV [BLOCK]

TV–PG [BLOCK]

B D [BLOCK]

L [BLOCK]

S [BLOCK]

V [BLOCK]

Selection Rating Category Explanations

TV-Y7

FV Fantasy Violence

TV-PG, TV-14, TV-MA

D Suggestive Dialog

(TV-PG, TV-14 only)

L Coarse Language

S Sexual Situation

VViolence

ACCESS CODE

_ _ _ _

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

B V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

TV–Y [VIEW]

B TV–Y7 ( ) [VIEW]

TV–G [VIEW]

TV–PG ( ) [VIEW]

TV–14 ( ) [VIEW]

TV–MA ( ) [VIEW]

PROTECTED PROGRAM

by TV-Y

– V-CHIP SET UP –

B TV RATING

MPAA RATING

CHANGE CODE

P20 Step

P21 Step

TV–Y [VIEW]

TV–Y7 ( ) [VIEW]

B TV–G [BLOCK]

TV–PG (DLSV ) [BLOCK]

TV–14 (DLSV) [BLOCK]

TV–MA ( LSV) [BLOCK]

CHANGE ACCESS CODE

Follow steps

in the “V-CHIP SET UP” sec-

tion on page 20.

4 Enter New code

Press the Number buttons to enter

your desired access code in the

“NEW CODE” space, then enter

the same code in the “CONFIRM

CODE” space. When completed, the menu will

return to “V-CHIP SET UP”.

•

Make sure you enter exactly the same new code in

the “CONFIRM CODE” space as one in the

“NEW CODE” space. If they are different, the

“NEW CODE” space is cleared for redoing.

5 Exit the V-Chip setting mode

Hit [SETUP] to exit the menu.

NOTE:

•

Your personal access code will be erased and will

return to the default (0000) when a power failure

occurs or when you turn off the power using a

wall switch. If you have forgotten the code, unplug

the power cord for 10 seconds to restore the access

code to 0000.

- 21 - EN

MPAA RATING SET UP

Follow steps

in the “V-CHIP SET UP” section

on page 20.

4 Select your desired item

Press [K / L] to point to your

desired item, then hit [ENTER] to

select [BLOCK] or [VIEW].

•

When you select a rating and set it to [BLOCK],

the higher ratings will be blocked automatically.

The lower ratings will be available for viewing.

•

When you set the lowest rating to [VIEW], all

other ratings will automatically be available for

viewing.

5 Exit the V-Chip setting mode

Hit [SETUP] to exit the menu.

Selection Rating Category Explanations

G General Audience

PG Parental Guidance suggested.

PG-13 Unsuitable for children under 13

R Restricted; under 17 requires accompa-

nying parent or adult guardian

NC-17 No one under 17 admitted

X Mature audience only

G [VIEW]

PG [VIEW]

PG–13 [VIEW]

B R [BLOCK]

NC–17 [BLOCK]

X [BLOCK]

1 Select “LANGUAGE”

Hit [SETUP].

Press

[K / L] to point to “LAN-

GUAGE”.

2 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”

Hit [ENTER] repeatedly to select “ENGLISH”,

“ESPAÑOL”= Spanish or “FRANÇAIS”= French.

3 Exit the Language mode

Hit [SETUP] to exit the menu.

NOTES:

•

This function effects only the language on the

screen menu and not the audio source.

•

If for some reason the menu is in Spanish or

French, hit [SETUP], press [K / L] to point to

“IDIOMA [ESPAÑOL]” or “LANGAGE

[FRANÇAIS]”, then hit [ENTER] repeatedly to

select desired language, then hit [SETUP].

MENU LANGUAGE

TV/VCR

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

B LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

NEW CODE

X X X X

CONFIRM CODE

_ _ _ _

- 22 - EN

MTS (Multi-Channel Television sound) SYSTEM

You can record or listen to a program in MTS stereo.

CHECKING THE SELECTED MTS MODE

By hitting [DISPLAY], the status shown below will

appear on the display when you play a VHS tape or

receive a broadcast on the unit tuner channel you are

watching.

PLAY B 12:00AM

HIFI CH 123

STEREO/SAP

SP COUNT 0:00:00

1) When a program is broadcast in stereo,

“STEREO” appears on the TV screen.

2) When a program is broadcast in second audio,

“SAP” appears on the TV screen.

3) When a program broadcast both in stereo and sec-

ond audio, “STEREO” and “SAP” appear on the

TV screen.

NOTE:

•

Although a program may be broadcast in both

stereo and second audio, you cannot record in

both stereo and second audio at the same time.

4) While the unit is set in HIFI stereo mode and

playback mode, “HIFI” appears on the TV screen.

While the unit is set in monaural (“MONO”)

mode, “HIFI” disappears from the TV screen.

NOTE:

•

If you play non-HIFI tapes while the unit is set

in “HIFI”, “HIFI” will disappear from the TV

screen and the unit will play automatically in

monaural.

MTS RECORDING/MONITOR MODE

Type of broadcast Display on STEREO/SAP Hi-Fi audio track (2-channel) Normal audio

the TV screen SELECTION L-channel R-channel track

Regular -None- -Invalid- Mono Mono Mono

(monaural audio)

Stereo broadcast STEREO -Invalid- L R L+R

Bilingual broadcast SAP STEREO* Main audio Main audio Main audio

program program program

SAP* Sub audio Sub audio Sub audio

program program program

Stereo & Bilingual STEREO STEREO* L R L+R

broadcast SAP

SAP* sub audio sub audio sub audio

program program program

*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.

SAP

Second Audio Program, which means your

program, can also be received in a second

language or sometimes a radio station.

HIFI

High Fidelity which produces better sound

than standard stereo units.

TV/VCR

- 23 - EN

SELECTING THE MTS SYSTEM

WHEN RECEIVING AN MTS BROADCAST

Hit [AUDIO] repeatedly to select the MTS output

mode.

•

The output mode changes as described below every

time you hit the button.

STEREO SAP MONO

•

The current mode appears on the TV screen for

about 5 seconds.

NOTES:

•

The initial setting is “STEREO”. The unit records

automatically MTS broadcasts in HIFI stereo sound

unless you select SAP mode recording beforehand.

•

This setting is saved even if the unit is turned off

or the AC cord is unplugged.

•

If you select second audio when second audio is

not available, the unit will record normal audio.

WHEN PLAYING CASSETTES

Hit [AUDIO] to select “HIFI” or “MONO”.

•

The current mode appears on the TV screen for

about 5 seconds.

•

The initial setting is “HIFI”.

•

This setting is saved until the cassette is ejected.

NOTES:

•

Normally “HIFI” should be selected for playback

with HIFI sound.

•

When you play non-HIFI tapes, the unit will play

only in the monaural mode even if you set HIFI.

WHEN IN THE EXTERNAL INPUT

MODE (“AUX”)

Hitting [AUDIO] does not affect the audio output

mode and the current audio output mode does not

appear on the TV screen.

TV/VCR

You can select the MTS output mode for recording or

watching the program, also the audio output mode

for playing cassettes.

- 24 - EN

VIDEO CASSETTE

This unit will operate with any cassette that has the mark. For best results, we recommend the use of

high-quality tapes. Do not use poor quality or damaged tapes.

REMOVING A CASSETTE

1)In the stop mode, hit [C / A STOP/EJECT] on the

unit. The cassette will be ejected.

2)Pull the cassette out of the cassette compartment.

3)Store the cassette in its case as shown.

NOTE:

•

In DVD mode, whether the cassette is with tab or

without tab you insert, it doesn’t start playing until

you hit

[B PLAY]

In TV/VCR mode, if the cassette without tab is

inserted, playback will automatically start.

PRECAUTIONS

•

Avoid moisture. Moisture condensation may occur

on the tape if it is moved from a cold place to a

warm place or vice versa. Before using a tape with

these conditions, to avoid damage of the tape and

your unit, wait until the tape has warmed to room

temperature and the moisture has evaporated.

•

Avoid extreme heat, high humidity and magnetic

fields.

•

Do not tamper with the cassette mechanism.

•

Do not touch the tape with your fingers.

INSERTING A CASSETTE

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the unit. The unit will

automatically turn on.

TWO DIFFERENT TAPE SPEEDS

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

NOTE:

•

You can play back a tape recorded in LP mode

(Long Play).

Tape Speed Recording/Playback Time

Type of tape

T60 T120 T160

SP mode 1 hour 2 hours 2-2/3 hours

SLP mode 3 hours 6 hours 8 hours

ERASE PREVENTION

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

If you decide to record on

the tape again, cover the

hole with plastic tape.

CORRECT

Window

WRONG

Ta b

Plastic Tape

- 25 - EN

PLAYBACK

NORMAL PLAYBACK

Make sure ...

•

The unit must be turned on.

1 Insert a prerecorded tape

If the erase-prevention tab has been removed, the

unit will start playback automatically.

2 To begin playback

Hit [PLAY O].

3 To stop playback

Hit [STOP C].

NOTES:

•

Even in the DVD mode, you can start the VCR

playback if you hit [

PLAY] (of the TV/VCR

side).

•

VCR playback will stop and the mode will change

to the DVD mode by pressing [SELECT],

[

PLAY] (DVD side) or [

OPEN/CLOSE].

TV/VCR

TRACKING ADJUSTMENT

•

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

Noise lines (black and white streaks) may appear

on the playback picture when playing pre-recorded

tapes or tapes recorded on other VCR. If this

occurs, press [CH. K / L] until the streaks disap-

pear.

•

You can reduce the noise lines by pressing

[CH. K / L] in the slow mode too. Tracking

adjustment in the slow mode will not be set auto-

matically.

•

To return to the Digital Auto Tracking function,

stop the tape once and start playback.

TV/VCR

PLAY

STOP

STILL PICTURE

You can view a still picture on the TV screen during

playback (the still mode). Hit [PAUSE F] during

playback. Only tapes recorded in the SLP mode will

show the least amount of lines. Hit [PLAY O] to

return to playback.

NOTES:

•

You can advance the picture one frame at a time by

hitting [PAUSE F] during the still mode.

•

If it is left in the pause mode for more than 5 min-

utes, the unit will automatically switch to the stop

mode.

TV/VCR

SLOW MOTION

Hit [PAUSE F], then hit [D] to start the playback

in slow motion. The unit mutes the sound during

slow motion. Hit [PLAY O] to return to normal

playback.

NOTE:

•

If it is left in the slow mode for more than 5 min-

utes, the unit will automatically go into the stop

mode.

TV/VCR

VERTICAL HOLD CONTROL

In the pause/still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

[CH. K / L].

NOTE:

•

If there are video noise lines on the screen, refer to

TRACKING ADJUSTMENT on this page.

TV/VCR

- 26 - EN

SPECIAL PLAYBACK

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

1 Select “USER’S SET UP”

Hit [SETUP].

Press

[K / L] to point to “USER’S

SET UP”, then hit [ENTER].

2 Set “RENTAL” to [ON]

Press [K / L] to point to

“RENTAL”.

Hit

[ENTER] until [ON] appears.

3 Exit the Rental setting

Hit [SETUP] to return to the TV mode.

4 Start playback

Hit [PLAY O] to start playback.

“RENTAL PLAY

B” appears.

•

Once you select the rental mode, it stays in effect

even after you turn off the unit.

TO CANCEL THE RENTAL MODE

Repeat steps 1 to 2 and select [OFF] using

[ENTER]. Hit [SETUP] to return to TV mode.

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

TV/VCR

Make sure ...

•

The unit must be turned on.

•

Insert a prerecorded tape.

RENTAL PLAYBACK

The unit has the auto repeat function that allows you to

repeat a tape indefinitely without hitting [PLAY O].

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

1 Select “USER’S SET UP”

Hit [SETUP].

Press

[K / L] to point to “USER’S

SET UP”, then hit [ENTER].

2 Select “ALL” or “BLANK”

Press [K / L] to point to “REPEAT

PLAY”.

Hit

[ENTER] repeatedly until your

desired selection [ALL] or

[BLANK] appears.

3 Exit the Repeat Play setting

Hit [SETUP] to return to the TV mode.

4 Start playback

Hit [PLAY O] to start the Repeat Play.

“REPEAT PLAY

B” appears.

•

Once you select the repeat play mode, it stays in

effect even after you turn off the unit.

•

If the rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

TO CANCEL THE REPEAT PLAY MODE

Repeat steps 1 to 2 and select [OFF] using

[ENTER]. Hit [SETUP] to return to TV mode.

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

TV/VCR

AUTO REPEAT PLAYBACK

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

B USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

–

USER’S SET UP

–

B RENTAL [ON]

REPEAT PLAY [OFF]

AUTO RETURN [OFF]

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

B USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

–

USER’S SET UP

–

RENTAL [OFF]

B REPEAT PLAY [ALL]

AUTO RETURN [OFF]

- 27 - EN

Make sure ...

•

The unit must be turned on.

•

Insert a tape.

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

NOTE:

•

Zero Return WILL NOT work on a blank tape or

a blank portion of a tape.

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

2 Reset the counter to 0:00:00

Hit [C.RESET] repeatedly.

3 Begin recording or playback

Press [RECORD] or [PLAY O].

Hit

[STOP C]

when recording or playback is com-

pleted.

4 To activate “ZERO RETURN”

Hit [SETUP].

Press

[K / L] to point to “ZERO

RETURN”, then hit [ENTER].

The unit will begin rewinding and

the counter will appear on the TV

screen.

The tape will automatically stop when the counter

returns to 0:00:00 (approx.).

TV/VCR

ZERO RETURN

The Time Search function makes it possible to quick-

ly advance the tape to your desired position simply

by entering the exact amount of playback time you

want to skip.

NOTE:

•

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

TV/VCR

TIME SEARCH

In the example below: To watch a program before/

after 2 hour 50 minutes from the present position, in

either direction.

1 Select “TIME SEARCH”

Hit [SETUP].

Press

[K / L] to point to “TIME

SEARCH”, then hit [ENTER].

2 Enter your desired time

Press

[K / L]

until your desired time

appears. (Example: “2:50” stands for

2 hours 50 minutes)

If you wish to cancel the Time

Search at this point, hit [SETUP].

3 Begin Time Search

By pressing [s

B], the unit will rewind or fast for-

ward to the specified point.

The time counts down during the search. When the

display shows

“

0:00

”

, the tape will start playback

automatically.

TO CANCEL DURING TIME SEARCH

Press [

C / A

STOP/EJECT] on the unit or

[

STOP

This will delete the selected time.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

B ZERO RETURN

TIME SEARCH

INDEX SEARCH

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

B TIME SEARCH

INDEX SEARCH

TIME SEARCH

2 : 50

PICTURE SEARCH

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

1 Start Picture Search

During playback, press [D] or [E] to view at a

high speed (in forward/reverse).

2 Change searching speed

Press [D] or [E] again to view at super high

speed (in the LP/SLP modes only).

TV/VCR

NOTE:

•

Tapes recorded in the SP or LP mode will normally

display a noise bar on the TV screen and the pic-

ture may revert to Black and White.

3 Return to normal speed

Hit [PLAY O].

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time will

not change on a blank tape or blank portions on the

tape.) The “–” indication will appear when the tape has

rewound further than “0:00:00” on the tape counter.

TV/VCR

SPECIAL FEATURES

REAL TIME TAPE COUNTER AUTO REWIND-EJECT

•

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the unit will eject the tape and turn itself

off.

•

This function is operative when Repeat Play is set

to the [OFF] position.

•

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

TV/VCR

- 28 - EN

INDEX SEARCH

This feature provides a method of indexing the start-

ing point so that it can be easily returned to in either

fast forward or rewind mode.

•

The index mark will be made automatically when

[RECORD] is hit. It will also be marked at the

starting point of Timer recording and OTR.

•

The index mark will not be recorded if [PAUSE F]

is hit and released during recording.

•

The time gap between making the index marks on

the tape should be greater than 1 minute for SP

recording, 2 minutes for LP recording and 3 min-

utes for SLP recording.

•

In some cases, the index mark at the beginning of

video tape cannot be detected.

Example: You are watching program number 4 and

want to fast forward to program number 7. You

must skip three programs.

TV/VCR

1 Select “INDEX SEARCH”

Hit [SETUP].

Press

[K / L] to point to “INDEX

SEARCH”, then hit [ENTER].

2 Enter your desired number

Press [K / L] until the number of

programs that you want to skip

appears.

(Example: “03” for 3 programs)

•

The Index Search mode will be canceled if the pro-

cedures are not activated in 30 seconds.

3 Begin Index Search

Press [s

B]. The unit begins rewinding or fast for-

warding to the beginning of desired program.

NOTE:

•

Every time an index signal is skipped, the number

in the program indicator decreases by one.

4 After Index Search

When the preset program is reached, the unit will

start playback automatically.

•

A video cassette must be inserted in the unit for

this function to work.

•

The number of Index Searches can be set up to 20.

•

This function will not operate in the recording mode.

•

When you want to cancel the Index Search while

in progress, hit [STOP C].

Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7

4321123

End of

the tape

Beginning of

the tape

CURRENT PLAYBACK PROGRAM

INDEX MARK

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

B INDEX SEARCH

INDEX SEARCH

0 3

- 29 - EN

RECORDING

Make sure ...

•

The unit must be turned on.

•

Insert a cassette tape with its erase-prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

NOTES:

•

This unit will ONLY record and view the same channel.

•

This unit cannot record the contents from the built-in DVD.

You can ONL

Y watch the same TV program that is

being recorded.

1 Select the channel to be recorded

Press the Number buttons or

[CH. K / L].

NOTE:

•

If the unit is connected to a cable box or satellite

box, the unit must be on CH3 or CH4, then the

channel to be recorded must be selected on the

cable box or satellite box.

2 Select the tape speed

Hit [SPEED] to select the desired

tape speed (SP/ SLP).

3 Begin recording

Hit [RECORD].

4 Stop recording

Hit [STOP C].

TV/VCR

NORMAL RECORDING

Hit [PAUSE F] to temporarily stop

recording.

Press

[PAUSE F] or [RECORD]

to resume recording.

NOTES:

•

After 5 minutes, the unit will

automatically switch to the recording mode to pre-

vent tape damage.

•

If Closed Caption mode is on, the On-Screen

Display will appear for 5 seconds, then disappear.

TV/VCR

SKIPPING UNWANTED

SCENES DURING RECORDING

REC

PAUSE

CH 10

This function enables you to set a recording length

simply by hitting [REC/OTR] on the unit.

Make sure ...

•

The unit must be turned on.

•

Insert a cassette tape with its erase-prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

NOTES:

•

You cannot start OTR with the remote control.

•

Recording starts immediately when [REC/OTR]

is hit.

•

When [REC/OTR] is hit 18 times, the unit returns

to the normal recording mode.

•

To stop the OTR operation, hit [C STOP] on the

unit or on the remote control.

•

To show the remaining time, hit [DISPLAY] on

the remote control so that “OTR” appears on the

TV screen. (It will show up momentarily then dis-

appear.)

•

Recording stops when the display shows 0:00.

•

Please note that in the SLP mode maximum

recording time, assuming the tape is started at the

beginning, is 8 hours using T-160 (or 6 hours

using T-120).

•

If the tape runs out before the end time, the unit

will switch to the stop mode immediately, ejects

the tape and turns itself off.

•

Even if [POWER] is hit during OTR, the unit

continues recording.

1 Select the channel to be recorded

Press the Number buttons or [CH. K / L].

NOTE:

•

If the unit is connected to a cable box or satellite

box, the unit must be on CH3 or CH4, then the

channel to be recorded is selected on the cable box

or satellite box.

2 Select the tape speed

Hit [SPEED] to select the desired tape speed

(SP/SLP).

3 Begin OTR

Hit [REC/OTR] on the unit as

many times as needed. The record-

ing length will be determined by

the number of times you hit

[REC/OTR]. Each time it is hit,

the recording time will be increased

by 30 minutes up to 8 hours.

TV/VCR

- 30 - EN

OTR (One Touch Recording)

Time(s) Display Recording length

1 time (normal recording)

2 times 0:30 30 minutes

3 times 1:00 60 minutes

17 times 8:00 480 minutes

You can make copies of video tapes made by friends

or relatives for your enjoyment.

You can not copy a DVD to a videotape.

Connect your unit and a source (Playing) VCR using

the following diagram.

1)Insert a pre-recorded video cassette into the source

VCR or camcorder.

2)Insert a blank video cassette or one you want to

record over, into the unit’s cassette compartment.

3)Hit

[SPEED] on remote control for the unit to

select the desired recording speed (SP/SLP).

4)Press

[CHANNEL K / L] on the unit until “AUX”

appears on the screen.

5)Hit

[REC/OTR] on the unit.

6)Begin playback of the tape in the source VCR or

camcorder.

NOTE:

•

For best results during copying, use the front

panel controls whenever possible. The remote

control might affect the source VCR’s playback

operation.

7)To stop copying, hit

[C / A STOP/EJECT] on the

unit, then stop the tape on the source VCR or cam-

corder.

TV/VCR

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder)

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

F. FWD

PLAY

STOP

HEADPHONE

VIDEO

–

AUDIO

–

EJECT

VIDEO

OUT

AUDIO

OUT

[Fig.8]

[Ex: Source VCR or

camcorder]

Audio/Video

cable

(not supplied)

[This unit]

OTR (2 : 30)

- 31 - EN

TIMER RECORDING

You may set the unit to start and end a recording

while you are away. You can set 8 programs to record

on specific days, daily or weekly within a 1 year

period.

In the example below, the timer is being set to record:

DATE: July 4th, 2005

SETTING TIME: from 7:30PM to 8:50PM

CHANNEL: CH61

TAPE SPEED: SP

Make sure ...

•

If a cable box or satellite box is connected with the

unit you will be limited to record only one channel,

and the channel selector on the unit must be select-

ed to the output channel of the boxes CH 3 or CH

4 and then the actual channel to be recorded must

be selected on the boxes.

•

Clock must be set to the correct time and date

before setting the timer.

•

The unit must be turned on to program it.

•

Insert a cassette tape with its erase-prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

•

The channel you want to record is properly set in

advance. (Refer to page 17.)

Avoid overlap of programs ...

There is a chance that a program will not be record-

ed, when programs overlap;

•

The program with an earlier start has priority.

•

Once the earliest program finishes, the overlapping

programs will begin recording in sequence.

•

When the starting time is the same, the program set

on the highest position in the program list has pri-

ority.

•

The illustration below demonstrates the sequence

of recordings.

Program 1 10:00AM - 11:00AM

Program 2 9:00AM - 10:00AM

Program 3 9:30AM - 12:00PM

TV/VCR

AUTOMATIC TIMER

RECORDING

9:00AM 10:00AM 12:00PM

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

9:30AM-12:00PM

11:00AM

Recording Sequence

*Recording period is SHADED

1 Select “TIMER PROGRAMMING”

Hit [SETUP].

Confirm “TIMER PROGRAM-

MING” is pointed by hitting

[K],

then hit [ENTER].

•

If you have not yet set the clock,

“MANUAL CLOCK SET” appears. If so, follow

steps 3 to 8 on page 18. Then set the timer record-

ing.

2 Select your desired program position (1 to 8)

Press [K / L] to select the desired

program position, then hit [B].

3 Set the channel number

Press [K / L] until the desired

channel number appears (Example:

CH61), then hit [B].

NOTE:

•

If the unit is connected to a cable box or satellite

box, the unit must be on CH3 or CH4, then the

channel to be recorded is selected on the cable box

or satellite box.

4 Select once, every day or weekly recording

For once recording :

Hit [K] until the desired date

appears. (Example: “7/04” for

July 4th)

Then hit [B].

For every day recording : To record a TV program

at the same time on the same channel every day.

(Example: Monday through Sunday)

Hit [L] until “EVRY DAY”

appears, then hit [B].

For weekly recording : To record a TV program at

the same time on the same channel every week.

(Example: every Monday)

Hit [L] until “EVRY” and your

desired day of the week appear

together, then hit

[B].

- TV/VCR SETUP -

B TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- - -:- - - -

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- - -:- - - -

61 -/- - - - - -:- - -:- - - -

- - -/- - - - - -:- - -:- - - -

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- - -:- - - -

61 EVRY DAY -:- - -:- - - -

- - -/- - - - - -:- - -:- - - -

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- - -:- - - -

61 7/04 MON -:- - -:- - - -

- - -/- - - - - -:- - -:- - - -

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- - -:- - - -

61 EVRY MON -:- - -:- - - -

- - -/- - - - - -:- - -:- - - -

- 32 - EN

NOTES:

•

The display will not be turned on automatically at

the time the programmed recording begins. To

watch the currently recorded TV program or to

play a DVD disc, hit [POWER] and [SELECT] to

choose the TV/VCR mode or the DVD mode.

•

If the tape runs out before the end time, the unit

will switch to the stop mode immediately and the

tape will be ejected.

TIMER PROGRAM EXTENSION

To shift the time schedule of an automatic timer

recording.

1)Hit

[POWER].

2)Repeat step

1 on page 31.

3)Hit

[RECORD] and select the desired program

using [K / L].

4)Hit

[RECORD] again.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, hit

[PAUSE F] on

the remote control. The recording time returns to

the original time.

NOTE:

•

When you shift forward the time schedule during

recording, the recording speed will automatically

be set to the SLP mode.

5)Press

[ENTER] or [RETURN] to exit the setting

menu. Then hit [SETUP] to return to original

mode.

TO CORRECT A PROGRAM

•

While setting a program; hit [s] to go back one

step and enter the correct numbers using [K / L].

•

After setting a program;

1)Hit [POWER].

2)Repeat steps

1 to 2 on page 31.

3)Hit

[B] (or hit [s] to go back one step) until the

part you want to correct begins flashing, then

make the changes using [K / L].

4)Hit

[POWER] to set automatic timer recording.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

1)Hit [POWER].

If recording is in progress, hit [

STOP/EJECT]

on the unit.

3)Repeat steps 1 to 2 on page 31 and select a pro-

gram you want to cancel.

4)Hit

[C.RESET].

5)Hit

[SETUP] to return to TV mode.

5 Set beginning hour

Press [K / L] until the desired hour

appears. (Example: “ 7, PM” for

7:30PM)

Then hit

[B].

6 Set beginning minute

Press [K / L] until the desired

minute appears. (Example: “30”

for 7:30PM)

Then hit

[B].

7 Set end hour

Press [K / L] until the desired hour

appears. (Example: “8, PM” for

8:50PM)

Then hit

[B].

8 Set end minute

Press [K / L] until the desired

minute appears. (Example: “50”

for 8:50PM)

Then hit

[B].

9 Set the tape speed

Press [K / L] until the desired tape

speed appears. (Example: “SP”)

10 Finish setting the program

Press [ENTER] or [RETURN] to complete setting.

•

To set another program, repeat steps 2 to 10.

•

Hit [SETUP] to exit the menu.

11 Set the timer

Hit [POWER] to set automatic timer recording. The

recording indicator lights up.

•

You must turn off the unit to activate automatic

timer recording.

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

•

If the erase-prevention tab is removed, the cassette

will be ejected when [POWER] is hit to off.

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- - -:- - - -

61 7/04 MON 7:12

M -:- - - -

- - -/- - - - - -:- - -:- - - -

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- - -:- - - -

61 7/04 MON 7:30

-:- - - -

- - -/- - - - - -:- - -:- - - -

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- - -:- - - -

61 7/04 MON 7:30

8:30

- -

- - -/- - - - - -:- - -:- - - -

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- - -:- - - -

61 7/04 MON 7:30

M 8:50

M- -

- - -/- - - - - -:- - -:- - - -

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- - -:- - - -

61 7/04 MON 7:30

8:50

- - -/- - - - - -:- - -:- - - -

- 33 - EN

TO CONFIRM THE TIMER SETTING

1)Hit [POWER] so that the Recording indicator light

goes off.

2)Hit

[SETUP].

3)Confirm “TIMER PROGRAMMING” is selected.

4)Hit

[ENTER]. The details of programs appear on

the TV screen.

5)Hit

[SETUP] to return to TV mode.

AUTO RETURN

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

1 Select “USER’S SET UP”

Hit [SETUP].

Press

[K / L] to point to “USER’S

SET UP”, then hit [ENTER].

2 Set “AUTO RETURN” to [ON]

Press [K / L] to point to “AUTO

RETURN”, then hit [ENTER] until

[ON] appears.

3 Auto Return will begin

When all the timer recordings are completed, the unit

will rewind to the beginning of the recorded pro-

gram(s).

NOTE:

•

If you hit [POWER] while tape is rewinding, the

Auto Return will stop.

4 Watch the recorded program

Hit [PLAY O].

TO CANCEL THE AUTO RETURN

MODE

Repeat steps 1 to 2 and select [OFF] using

[ENTER].

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

TV/VCR

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

B USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

–

USER’S SET UP

–

RENTAL [OFF]

REPEAT PLAY [OFF]

B AUTO RETURN [ON]

- 34 - EN

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, hit [DISPLAY]

. Each time you hit [DIS-

PLAY], the TV screen will change as follows:

When the Closed Caption mode is OFF:

•

Counter mode: After 5 seconds, only the counter

remains. To clear it, hit [DISPLAY].

•

Clock mode: After 5 seconds, only the clock and

the channel number remain. To clear them, hit

[DISPLAY].

When the Closed Caption mode is ON:

•

The On Screen Display disappear after 5 seconds.

•

This is true even if [MUTE] or [PAUSE F] is

pressed while recording.

OFF mode Clock/Counter mode

STOP 5:40 PM

CH2

SP COUNT 0:12:34

STOP STOP

SP SPCOUNT 0:12:34

COUNT 0:12:34

5:40PM

CH2

5:40PM

CH2

Counter

remains

Clock & Channel

remains

After 5 seconds After 5 seconds

OFF mode Counter mode Clock mode

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

TV Display

CATV channel

TV Display

W+80 W+81 W+82 W+83 W+84

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

W+55 W+56 W+57 W+58 A-4 A-3 A-2 A-1 W+59 W+60 W+61 W+62 W+63 W+64

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

A-5

RSTUVWW+1 W+2 W+3 W+4 W+5 W+6 W+7 W+8 W+9

CDEFGH I JKLMNOPQ

5A 2 3 4 5 6 7 8 9 10 11 12 13 A B

1234567891011 12 13 14 15

16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

91 92 93 94 95 96 97 98 99 100 101 102 103 104 105

106 107 108 109 110 111 112 113 114 115 116 117 118 119 120

121 122 123 124 125

CATV channel

- 35 - EN

DVD SECTION

ABOUT THE DISCS

If you cannot play back a disc which bears one of the marks above, check the following notes.

*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot

be played back.

*2:

Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.

*3: Discs recorded in the VR (Video Recording) format cannot be played back.

*4: Scratched or stained discs may not be played back.

*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the

recorder or special properties of discs.

*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not

play them back. Even if they are played back, the sound or video quality will be compromised.

*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD

recorder. However, depending on the recording status of a disc, the disc may not be played back at all or

normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with

the DVD recorder. Refer to the manual accompanying the DVD recorder.

*8: Only the discs recorded in the video format and finalized can be played back.

Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be

played back at all or normally (the picture or sound may not be smooth, etc.).

*9: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may not

play back properly.

*10:

Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.

*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-

mat can only be played back on unit with the same region code.

DVD-Video

* 1,2,4,6,10,11

* 4,6,10

* 4,5,6,9,10

* 1,3,4,5,6

7,9,10

DVD-RW

DVD-R

* 1,3,4,5,6,8,9,10

DVD+RW

DVD+R

Audio CD

CD-RW

CD-R

Digital video

(MPEG2)

Digital audio

Region code

Mark (logo)

Playable

discs

Recorded

signals

Disc size

Disc types

12 cm

8 cm

12 cm

8 cm

Example

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1

Chapter 2

Chapter 3 Chapter 4

Example

Tr ac k 1

Tr ac k 2

Tr ac k 5

Tr ac k 6

Tr ac k 3

Tr ac k 4

Audio CD

NEVER play back the following discs. Otherwise, malfunction may result!

DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /

DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3

On the following disc, the sound MAY NOT be heard.

Super Audio CD

NOTE: Only the sound recorded on the normal CD layer can be delivered.

The sound recorded on the high density Super Audio CD layer cannot be delivered.

Any other discs without compatibility indications

PLAYABLE DISCS

UNPLAYABLE DISCS

is a trademark of DVD Format/Logo Licensing Corporation.

- 36 - EN

PLAYING A DISC

BASIC PLAYBACK

Getting started

¡Turn on the power of amplifier and any other com-

ponents, if necessary.

1 Hit [POWER].

¡The power will turn on.

2 Hit [A OPEN/CLOSE] to open disc loading

tray.

3 Place the chosen disc in the tray, with the

label facing up.

DVD-V

4 Hit [PLAY O].

¡The tray will close automatically and playback will

then start from the first chapter or track of the disc.

¡Closing the disc tray manually or by hitting

[A OPEN/CLOSE] also starts playback.

¡If the playback does not start automatically, hit

[PLAY O].

¡When you playback a DVD which features a title

menu, it may appear on the screen. In this case, refer

to “TITLE MENU” on this page.

5 Hit [STOP C] to stop playback.

NOTES:

¡When the DVD mode has been switched to the

TV/VCR mode, the DVD mode shuts down first and

then the TV picture and sound appears in about 4 sec-

onds. Similarly, when

[POWER] is hit to turn off in

the DVD mode, this mode shuts down first and then

the unit is turned off.

¡A “prohibited icon” may appear at

the top-right on the TV screen dur-

ing operation, warning that a pro-

hibited operation has been encoun-

tered by the DVD or the disc.

¡With DVDs that use titles for playback program sig-

nals, playback may start from the second title or it

may skip these titles.

¡During the playback of a two layered disc, pictures

may stop for a moment. This happens when the 1st

layer switches to the 2nd layer. This is not a mal-

function.

GENERAL FEATURES

VD may contain menus to navigate the disc and

access special features. Press the appropriate

Number buttons or [K / L / s / B] to highlight

your selection in the DVD main menu and hit

[ENTER] to confirm.

NOTES:

¡Select DVD mode by hitting [SELECT], then oper-

ate the DVD functions.

¡Unless stated, all operations described are based on

remote control use. Some operations can be carried

out using the menu bar on the TV screen.

DVD-V

TITLE MENU

1 Hit [TITLE].

¡The title menu will appear.

¡If the feature is not available, symbol may

appear on the TV screen.

2 Press [K / L / s / B] to select an item, and

hit [ENTER] to confirm selection.

DVD-V

DISC MENU

1 Hit [DISC MENU].

¡The DVD main menu will appear.

¡If the feature is not available, symbol may

appear on the TV screen.

¡If disc menu is available on the disc, audio lan-

guage, subtitle options, chapters for the title and

other options will appear for selection.

2 Press [K / L / s / B] to select an item and

hit [ENTER] to confirm selection.

DVD-V

CALLING UP A MENU SCREEN

DURING PLAYBACK

¡Hit [DISC MENU] to call up the DVD menu.

¡Hit [TITLE] to call up the title menu.

NOTE:

¡Contents of menu and corresponding menu opera-

tions may vary between discs. Refer to the manual

accompanying the disc for details.

- 37 - EN

STEP BY STEP PLAYBACK

1 During playback, hit [PAUSE F].

¡Playback will pause and sound will be muted.

2 The disc goes forward by one frame each

time [PAUSE

F] is hit.

To exit step by step playback, hit [PLAY O].

DVD-V

RESUME

1 During playback, hit [STOP C].

¡Resume message will appear on the TV screen.

2 Hit [PLAY O], playback will resume from the

point at which playback was stopped.

¡To cancel resume, hit [STOP C] twice.

¡The resume information stays on even when the

power is turned off.

DVD-V

1 During playback, press and hold [g] or

[

h] for a few seconds.

¡“ g 1” or “h 1” appears on the screen.

2 To select another speed, repeat step 1 until

your required speed number appears on the

screen.

¡For DVDs, fast forward/reverse search speed is dif-

ferent depending on the disc. Approximate speed is

1(×2), 2(×8), 3(×20), 4(×50) and 5(×100).

¡For Audio CDs approximate speed is 1(×2), 2(×8)

and 3(

×30).

¡When you press buttons on the main unit, use

[SEARCHh / g].

To return to normal playback, hit [PLAY O]

DVD-V

FAST FORWARD /

FAST REVERSE

PAUSE

1 During playback, hit [PAUSE F].

¡Playback will pause and sound will be muted.

2 To continue playback, hit [PLAY O].

DVD-V

SLOW FORWARD /

SLOW REVERSE

1 During playback, hit [PAUSE F].

2 Press and hold [g] or [h] for a few

seconds.

¡“ 1” or “ 1” appears on the screen.

3 To select another speed, repeat step 2 until

your required speed number appears on the

screen.

¡Slow forward or reverse speed varies with the disc.

Approximate speed is 1(1/16), 2(1/8) and 3(1/2).

¡When you press buttons on the main unit, use

[SEARCHh / g].

To return to normal playback, hit [PLAY O].

DVD-V

ZOOM

The Zoom function allows you to enlarge the video

image and to pan through the enlarged image.

1 Hit [ZOOM] during playback.

¡Playback will continue.

2 Hit [ZOOM] repeatedly to select the required

zoom factor: ZOOM1, ZOOM2, ZOOM3 or

OFF.

3 Press [K / L / s / B] to move the zoomed

picture across the screen.

4 To exit zoom mode, hit [ZOOM] to OFF.

NOTES:

¡Zooming function does not work while disc menu is

shown.

¡Zooming function is not available on some discs.

¡It may take several seconds to slide the zoomed pic-

ture.

¡The picture may be distorted if you operate other

functions repeatedly (ex. [PAUSE

] or [

], etc.)

in the zoom mode.

DVD-V

- 38 - EN

SEARCH FUNCTION

TRACK SEARCH

There are three ways to begin playback on an Audio

CD at a specific track.

Using the Number buttons

1 Press the Number buttons to enter the

desired track number.

¡Playback will start at the selected track.

¡For single digit tracks (1-9), press a single number

(eg. track 3, hit [3]).

¡To play track 26, hit [+10], [2], [6].

Using [SEARCH MODE]

1 Hit [SEARCH MODE].

¡The track search display appears.

2 Within 30 seconds, select the desired track

number using the Number buttons.

¡For single digits hit [0] first, if the total track of the

disc is 10 tracks or more.

¡Playback will start at the selected track.

Using [

]

During playback, hit [G] to move the next track. Hit

it repeatedly to skip subsequent tracks. Hit [H] to go

back to beginning of the current track. Hit it repeated-

ly to go to the previous tracks.

¡If [H / G] is pressed while the playback is

paused, the playback will be paused again after skip-

ping to the next track.

NOTE:

¡[H / G ] are not operative when playback is

stopped.

TITLE / CHAPTER SEARCH

1 Hit [SEARCH MODE] once for the Chapter

search, twice for the Title search during

playback.

2 Enter the desired chapter/title number using

the Number buttons.

¡Playback will start at the selected chapter or title.

¡Hit [CLEAR] to erase the incorrect input.

¡For single digits hit [0] first, if the total number of

chapter or title of the disc is 10 or more.

DVD-V

_/2

TIME SEARCH

1 During playback, hit [SEARCH MODE] three

times (CD: twice) to display the Time Search

on the TV screen.

2 Within 30 seconds, enter a desired disc

time using the Number buttons.

¡Playback will start at the specified time.

¡Hit [CLEAR] to erase the incorrect input.

¡When there is no need to enter a number, “0”

appears automatically. For example, “ 0 : 0

- -

”

appears in the Time Search display if the total time

of the track or title is less than 10 minutes.

DVD-V

MARKER SETUP SCREEN

Use markers to memorize your favorite places on a

disc.

1 Hit [SEARCH MODE] four times (CD: three

times) during playback.

¡The display screen and Markers will appear on the

TV screen.

2 Press [s / B] to select 1, 2, 3, 4, 5, 6, 7, 8, 9,

or 10 and ensure that “

- - - -

- -

”

appears in the display.

3 When you reach the desired point, hit

[ENTER].

¡The Title or Track and elapsed playing time will

appear in the TV screen.

4 To return to the Marker later, hit [SEARCH

MODE] four times (CD: three times) during

playback and press [

s / B] to choose the

desired marker, then hit [ENTER].

NOTES:

¡Operations which erase all Markers:

– Opening the disc tray.

– Turning off the power.

– Hitting [SELECT].

– Selecting “AC” at step

2 and hitting [ENTER].

¡To clear a marker:

– Press [s / B] to select a cursor on to the marker

number and hit

[CLEAR].

¡You can mark up to 10 points.

5 Press [SEARCH MODE] or [RETURN] to

exit.

DVD-V

- 39 - EN

SPECIAL PLAYBACK FUNCTION

REPEAT

REPEAT TITLE / CHAPTER

To activate the repeat function, hit [REPEAT]

during playback.

¡The repeat mode changes as described below every

time you hit the button.

DVD-V

REPEAT is available only during playback.

CHAPTER TITLE OFF

(current chapter repeat) (current title repeat)

(repeat

off)

NOTES:

¡Repeat Title/Chapter is not available with some

scenes.

¡The REPEAT setting will be cleared when moving

to other title or chapter.

REPEAT TRACK

To activate the repeat function, hit [REPEAT]

during playback.

¡The repeat mode changes as described below every

time you hit the button.

TRACK ALL OFF

(current track repeat) (entire disc repeat)

(repeat

off)

NOTES:

¡Repeat setting will be cleared when moving to other

track.

¡Repeat playback does not function during A-B

repeat playback.

A-B REPEAT

1 Hit [A-B] at your chosen starting point.

¡“ A-” appears briefly on the TV screen.

2 Hit [A-B] again at your chosen end point.

¡“ A-B” appears briefly on the TV screen, and the

repeat sequence begins.

3 To exit the sequence, hit [A-B].

NOTES:

¡The A-B repeat section can only be set within the cur-

rent title (for DVDs) or current track (for Audio CDs).

¡A-B repeat is not available with some scenes in DVD.

¡To cancel the A point which was set, hit [CLEAR].

¡A-B repeat playback does not function during title,

chapter, track or all repeat playback.

DVD-V

PROGRAM

You may determine the order in which tracks will play.

1 In the stop mode, hit [MODE].

¡The “PROGRAM” screen will appear.

2 Press [▲ / ▼] to select a track, then hit

[ENTER].

¡Hit [CLEAR] to erase the

most recently entered track.

¡If the entire Program cannot be

displayed at once on a screen,

“G” appears to go to the next

page and “H” appears to go

back to the previous page.

3 Repeat step 2 until you have selected all the

tracks you want to play in the program.

Hit [PLAY O] to play the programmed tracks.

NOTES:

¡While the program is being played back, hitting

[STOP C] works as follows.

¡Hit [STOP C] once and then [PLAY O] again,

playback will restart from the point where

[STOP C] was hit. (Program continued)

¡Hit [STOP C] twice and then [PLAY O] again,

playback will restart from the track in the usual

way. (Program canceled)

¡Up to 99 tracks can be entered.

¡To erase all tracks in the program at once, select

“ALL CLEAR” at the bottom of the list at step 2.

¡If you like to repeat the current track in the pro-

gram, hit [REPEAT] several times until “

TRACK” appears during playback. If you like to

repeat the entire program hit [REPEAT] several

times until “ ALL” appears during playback.

TOTAL 1:03:30

2/3

1/4

1 3:30

5 5:10

10 4:20

11 3:00

12 3:20

17 4:10

22 2:50

1 3:30

CD-DA

ENTER

CLEAR

PLAY

2 4:30

3 5:00

4 3:10

5 5:10

6 1:30

7 2:30

PROGRAM

RANDOM PLAYBACK

This function shuffles the playing order of tracks

instead of playback in the sequence.

1 In the stop mode, hit [MODE] twice.

¡“RANDOM” screen appears.

2 Hit [PLAY O] to start random playback.

NOTE:

If you like to repeat the current track in the random

selection, hit

[REPEAT] several times until “

TRACK” appears during playback. If you like to

repeat the entire random selection hit

[REPEAT] sev-

eral times until “ ALL” appears during playback.

PLAY

CD-DA TOTAL 0:45:55

RANDOM PROGRAM

- - no indication - -

RANDOM

- 40 - EN

CHANGING THE SETTINGS

AUDIO LANGUAGE

The unit allows you to select a language during DVD

disc (if multi languages are available) playback.

1 Hit [AUDIO] during playback.

2 Hit [AUDIO] repeatedly to select your

desired language.

NOTE:

¡Hitting [AUDIO] may not work on some DVDs with

multiple audio languages (e.g. DVDs which allow

audio language setting on the disc menu).

DVD-V

STEREO SOUND MODE

1 Hit [AUDIO] repeatedly during playback to

select between “STEREO”, “L-ch” or “R-ch”.

STEREO - both right and left channels are active (stereo)

L-ch - only left channel is active

R-ch - only right channel is active

The unit allows you to select a language for subtitles

during DVD disc (if available) playback.

1 Hit [SUBTITLE] during playback.

¡The subtitle language will

appear on the display bar at

the top of the TV screen.

2 Hit [SUBTITLE] repeatedly to select your

desired subtitle language.

3 To turn off subtitles, hit [SUBTITLE] repeat-

edly until “OFF” appears.

NOTES:

¡Hitting [SUBTITLE] may not work on some

DVDs with multiple subtitle languages. In this

case, set it on the disc menu. (Operation varies

between discs. Refer to the manual of the disc.)

¡If the desired language is not shown after hitting

[SUBTITLE] several times, the disc does not have

subtitles in that language.

¡When “NOT AVAILABLE”

appears on the TV screen, it

means no subtitle is recorded

on the scene.

¡If you choose a language that has a 3 letter lan-

guage code, the code will be displayed every time

you change the Subtitle language setting. If you

choose any other languages, “---” will be displayed

instead. (Refer to page 43.)

DVD-V

SUBTITLE LANGUAGE

1.ENG/6

1.ENG Dolby D 3/2.1ch 48k/ 3

STEREO

NOT AVAILABLE

- 41 - EN

CAMERA ANGLE

Some DVD discs contain scenes which have been shot

simultaneously from various angles. You can change

the camera angle when the “ ” icon appears on the

screen.

1 Hit [ANGLE] during playback.

¡The selected angle will be displayed on the display

bar at the top of the screen.

¡If the “ANGLE ICON” setting is “OFF” in the

“OTHERS” menu, the “ ” icon will not appear.

(Refer to page 45.)

2 Hit [ANGLE] repeatedly to select your

desired angle.

DVD-V

Adjust the Black Level Settings to make the black

parts of the picture brighter.

1 Hit [MODE] during playback.

2 Hit [ENTER] to switch “ON/OFF”.

ON: Makes the dark parts brighter.

OFF: Shows the original picture as recorded.

(Initial setting)

3 Press [MODE] twice or [RETURN] to exit.

NOTE:

¡The setting will be saved even if the unit is turned

off.

DVD-V

BLACK LEVEL SETTING

You can enjoy surround-sound effect over two speak-

ers on this unit.

1 Hit [MODE] twice (CD: once) during play-

back.

2 Hit [ENTER] to set it “1” (Natural effect), “2”

(Emphasized effect) or “OFF”.

3 Hit [RETURN] to exit.

NOTE: (for CD play only)

¡Virtual Surround will not be effective if the sound

mode is set to something other than STEREO.

DVD-V

VIRTUAL SURROUND

OFF

1 / 8

OFF

- 42 - EN

For DVD-Vs

1 Hit [DISPLAY] during playback to show cur-

rent Chapter.

¡The elapsed and remaining

playing time of the current

chapter will be displayed.

Hit [DISPLAY] again to show current Title.

¡The elapsed and remaining

playing time of the current

title will be displayed.

3 Hit [DISPLAY] again.

¡The bit rate and the current

repeat setting will be dis-

played.

¡If you are playing a dual layered disc, the layer

number will also be displayed (L0: Layer 0 is play-

ing. L1: Layer 1 is playing).

4 Hit [DISPLAY] again to exit.

THE ON-SCREEN INFORMATION

For Audio CDs

1 Hit [DISPLAY] during playback to show the

current Track.

¡The elapsed and remaining playing time of the cur-

rent track will be displayed.

2 Hit [DISPLAY] again to show current Total

Track.

¡The elapsed and remaining playing time of the total

track will be displayed.

3 Hit [DISPLAY] again to exit.

NOTE:

¡When you are playing a disc in PROGRAM or

RANDOM mode, “ PROGRAM”

(or RANDOM) will be displayed at step 2.

You can check the information about the current disc by hitting [DISPLAY].

DVD-V

9/49 0:00:00 -0:03:30

4/12 0:03:21 - 0:02:15

4/12 0:13:45 - 0:45:40

1/3 0:00:00 - 1:23:45

TL1

PROGRAM B

- 43 - EN

CHANGING THE DVD SET UP ITEMS

CUSTOM MENU

You can change the DVD player’s settings.

1 Hit [SETUP] twice in the stop mode so that

the DVD SETUP menu appears.

¡Hit [L] to select “CUSTOM”

then hit [ENTER].

NOTE:

¡If the menu does not appear, hit [PLAY

] first,

then hit [STOP C]. Make sure the disc is in the stop

mode, then slowly hit [SETUP] twice.

2 Select the desired item.

¡Press [K / L] to select the desired item then hit

[ENTER] to confirm.

Refer to the pages below to set up each item.

LANGUAGE SETTING

Follow steps

in the “CUSTOM MENU” section

above.

3 Press [K / L] to select the desired item then

hit [ENTER].

AUDIO:

Sets the audio language.

SUBTITLE:

Sets the subtitle language.

DISC MENU:

Sets the language for DVD menu.

4 Press [K / L] to select a setting then hit

[ENTER].

¡If “OTHER” is selected on

the “AUDIO”, “SUBTITLE”

or “DISC MENU” screen,

press four-digit number to

enter the code for the desired

language. (Refer to the lan-

guage code list.)

¡Only the languages support-

ed by the disc can be select-

ed.

5 Hit [SETUP] to exit the menu.

NOTES:

¡Language Setting for Audio and Subtitle are not

valid for some discs due to default setting of the

disc. In this case, set them by hitting [AUDIO] and

[SUBTITLE]. (Refer to page 40.)

¡If you select a language that is not supported by the

disc, subtitle will automatically be set OFF and the

first item of the audio languages will be automatical-

ly set.

DVD-V

If you choose a language that has a 3 letter language

code, the code will be displayed every time you change

the AUDIO or SUBTITLE language setting above. If

you choose any other languages, ‘---’ will be displayed

instead. (3 letter language code is written in bracket.)

Language Code

A-B

Abkhazian 4748

Afar 4747

Afrikaans 4752

Albanian 6563

Amharic 4759

Arabic 4764

Armenian 5471

Assamese 4765

Aymara 4771

Azerbaijani 4772

Bashkir 4847

Basque 5167

Bengali;Bangla 4860

Bhutani 5072

Bihari 4854

Bislama 4855

Breton 4864

Bulgarian 4853

Burmese 5971

Byelorussian 4851

C-E

Cambodian 5759

Catalan 4947

Chinese [CHI] 7254

Corsican 4961

Croatian 5464

Czech 4965

Danish [DAN] 5047

Dutch [DUT] 6058

English [ENG] 5160

Esperanto 5161

Estonian 5166

F-H

Faroese 5261

Fiji 5256

Finnish [FIN] 5255

French [FRE] 5264

Frisian 5271

Galician 5358

Georgian 5747

German [GER] 5051

Greek [GRE] 5158

Greenlandic 5758

Guarani 5360

Gujarati 5367

Hausa 5447

Hebrew 5569

Hindi 5455

Hungarian [HUN] 5467

I-K

Icelandic [ICE] 5565

Indonesian 5560

Interlingua 5547

Interlingue 5551

Inupiak 5557

Irish [IRI] 5347

Italian [ITA] 5566

Japanese [JPN] 5647

Javanese 5669

Kannada 5760

Kashmiri 5765

Kazakh 5757

Kinyarwanda 6469

Kirghiz 5771

Kirundi 6460

Korean [KOR] 5761

Kurdish 5767

Language Code

L-N

Laothian 5861

Latin 5847

Latvian;Lettish 5868

Lingala 5860

Lithuanian 5866

Macedonian 5957

Malagasy 5953

Malay 5965

Malayalam 5958

Maltese 5966

Maori 5955

Marathi 5964

Moldavian 5961

Mongolian 5960

Nauru 6047

Nepali 6051

Norwegian [NOR] 6061

O-R

Occitan 6149

Oriya 6164

Oromo(Afan) 6159

Panjabi 6247

Pashto;Pushto 6265

Persian 5247

Polish 6258

Portuguese [POR] 6266

Quechua 6367

Rhaeto-Romance 6459

Romanian [RUM] 6461

Russian [RUS] 6467

Samoan 6559

Sangho 6553

Sanskrit 6547

Scots Gaelic 5350

Serbian 6564

Serbo-Croatian 6554

Sesotho 6566

Setswana 6660

Shona 6560

Sindhi 6550

Singhalese 6555

Siswat 6565

Slovak 6557

Slovenian 6558

Somali 6561

Spanish [SPA] 5165

Sundanese 6567

Swahili 6569

Swedish [SWE] 6568

Tagalog 6658

Tajik 6653

Tamil 6647

Tatar 6666

Telugu 6651

Thai 6654

Tibetan 4861

Tigrinya 6655

Tonga 6661

Tsonga 6665

Tu rkish [TUR] 6664

Tu rkmen 6657

Tw i 6669

U-Z

Ukrainian 6757

Urdu 6764

Uzbek 6772

Vietnamese 6855

Volapuk 6861

Welsh 4971

Wolof 6961

Xhosa 7054

Yiddish 5655

Yo r uba 7161

Zulu 7267

SETUP LANGUAGE

AUDIO

SUBTITLE

DISC MENU

ORIGINAL

OFF

ENGLISH

SUBTITLE

OFF

ENGLISH

FRENCH

SETUP LANGUAGE

DISC MENU

ENGLISH

FRENCH

SPANISH

SETUP LANGUAGE

AUDIO

ORIGINAL

ENGLISH

FRENCH

SETUP LANGUAGE

SETUP

QUICK

CUSTOM

INITIALIZE

SETUP CUSTOM

LANGUAGE

DISPLAY

AUDIO

PARENTAL

OTHERS

P43 Step

P44 Step

P45 Step

- 44 - EN

AUDIO SETTING

Choose the appropriate Audio settings for your equip-

ment as it only affects during the playback of DVD

discs.

Follow steps

in the “CUSTOM MENU” sec-

tion on page 43.

3 Press [K / L] to select the below items then

hit [ENTER].

DRC (Dynamic Range

Control):

¡To compress the range of soft

to loud sound.

¡The default setting is “ON”.

DOWN SAMPLING:

¡ON : Output in 48 kHz.

(default)

¡OFF : Output the original

sound.

When playing disc with copyright Protection

¡If you select “OFF”, copyright protection will be

activated and sound will be down sampled at 48kHz.

DOLBY DIGITAL:

Set to “BITSTREAM” when

the unit is connected to a

Dolby Digital Decoder.

¡BITSTREAM: Output a Dolby Digital signal

(default)

¡PCM: Convert the Dolby Digital to PCM

(2 channel stereo)

4 Hit [SETUP] to exit the menu.

QUICK

DRC ON

DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

SETUP AUDIO

DRC ON

DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

SETUP AUDIO

DRC ON

DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

SETUP AUDIO

LANGUAGE SETTING FOR THE ON-SCREEN MENUS

¡You can access the TV/VCR SETUP menu by hitting [SETUP] from the DVD mode. Refer to

“MENU LANGUAGE” on page 21 to change the language for the on-screen menus.

DISPLAY SETTING

Follow steps

in the “CUSTOM MENU” sec-

tion on page 43.

3 Press [K / L] to select the below items then

hit [ENTER].

TV MODE:

You can change certain aspects of the DVD display

screens and on-screen messages on the TV screen.

¡4:3 LETTER BOX (default):

To show black bars on top

and bottom of the screen.

¡4:3 PAN & SCAN: To show

a full height picture with both sides trimmed.

STILL MODE

This function allows you to adjust picture resolution

and quality in the still mode.

¡AUTO (default):

Automatically select the best

resolution setting (FRAME

or FIELD) based on the data

characteristics of the pictures.

¡FIELD: Select “FIELD” when the pictures are still

unstable even if “AUTO” is selected.

FIELD stabilizes the pictures, although the picture

quality may become coarse due to the limited

amount of data.

¡FRAME: Select “FRAME” to display relatively

motionless pictures in higher resolution.

FRAME improves the picture quality, although it

may unstabilizethe pictures due to simultaneous

output of two field data.

4 Hit [SETUP] to exit the menu.

QUICK

TV MODE

4:3 LETTER BOX

STILL MODE

AUTO

SETUP DISPLAY

TV MODE

4:3 LETTER BOX

STILL MODE

AUTO

SETUP DISPLAY

QUICK MENU

¡You can select the “TV MODE” or “DOLBY DIGITAL” from the QUICK menu quickly. To access the

QUICK menu, select “QUICK” instead of “CUSTOM” at step

on page 43.

- 45 - EN

CONTROL LEVELS

ALL

All parental lock is cancelled.

Level 8

DVD software of any grade (adult/general/children)

can be played back.

Levels 7 to 2

Only DVD software intended for general use and

children can be played back.

Level 1

Only DVD software intended for children can be

played back, with those intended for adult and

general use prohibited.

PARENTAL CONTROL

Parental Control limits the disc viewing that exceed

your setting (with a password or playback will stop).

This feature allows you to prevent discs with alterna-

tive scenes from being played by your children.

PARENTAL LEVEL

Parental Level allows you to set the rating level of

your DVD discs. Playback will stop if the disc’s rat-

ings exceed the level you set.

Follow steps

in the “CUSTOM MENU” sec-

tion on page 43.

3 Enter your four-digit password then hit

[ENTER].

4 Press [K / L] to select “PARENTAL LEVEL”

then hit [ENTER].

5 Press [K / L]to select the desired level

then hit [ENTER].

6 Hit [SETUP] to exit the menu.

NOTES:

When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the pass-

word. (in the event you forget the password, see below)

¡To change the password, press [K / L] to select

“PASSWORD CHANGE” at step 4 then hit

[ENTER]. Enter the four-digit password, then hit

[ENTER].

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set.

¡Record the password in case you forget it.

IF YOU FORGET THE PASSWORD

1 Hit the Number buttons [4], [7], [3], [7] at

step 3. Then enter your new password.

¡Password will be cleared and parental level will be

set to “ALL”.

2 Proceed with steps 4 to 6 again.

This allows you to return all selections of SETUP

(except for “PARENTAL” and menu language) to

their default settings.

1 Hit [SETUP] twice in the stop mode so that

the “INITIALIZE” menu appears.

2 Press [K / L] to select “INITIALIZE” then hit

[ENTER].

3 Press [K / L] to select “YES” then hit

[ENTER] twice.

All the settings (except for

“PARENTAL” and

language) will be cleared.

¡To cancel the initialization,

select “NO”.

4 Hit [SETUP] to exit the menu.

DVD-V

OTHER SETTINGS

Follow steps

in the “CUSTOM MENU” sec-

tion on page 43.

3 Press [K / L] to select the below items,

then hit [ENTER].

ANGLE ICON:

¡Hit [ENTER] repeatedly to turn Angle icon “ON” or

“OFF”.

¡The default setting is “ON”.

AUTO POWER OFF:

¡Hit [ENTER] repeatedly to turn Auto Power off

“ON” or “OFF”.

The default setting is “ON” and the screen saver pro-

gram starts when there is no input from the unit for 5

minutes in the stop mode. After the screen saver pro-

gram is activated for 15 minutes, the power is auto-

matically turned off.

4 Hit [SETUP] to exit the menu.

SETUP PARENTAL

PASSWORD

Enter current password.

PASSWORD CHANGE

PARENTAL LEVEL ALL

SETUP PARENTAL

PARENTAL LEVEL

ALL

7 [NC-17]

6 [R]

SETUP PARENTAL

SETUP OTHERS

ANGLE ICON

AUTO POWER OFF

SETUP

QUICK

CUSTOM

INITIALIZE

SETUP INITIALIZE

Initialize?

YES

INITIALIZE

- 46 - EN

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked

possibilities. Before arranging for service, check these items. It could save your time and money.

TV/VCR Mode

TROUBLESHOOTING GUIDE

PROBLEM CORRECTIVE ACTION

No picture or sound

•

Make sure the AC cord is connected to an AC outlet.

•

Check antenna connection.

•

Hit [SELECT] to select TV mode.

Then try other TV feature.

•

Let the unit program its tuner memory.

No picture or poor picture on the

•

Adjust direction or replace antenna.

unit

•

Adjust picture controls.

•

Check for broken pin of the antenna cable.

No sound or poor sound

•

Adjust volume control on remote control or main unit.

•

Hit [MUTE] to restore sound.

Bars On Screen

•

If outside antenna is being used, check for broken wire.

•

Check for local interference.

Picture Distorted or Blurred

•

Try a new channel, if OK, then possible station trouble.

•

If outside antenna is being used, check for broken wire.

Picture Rolls Vertically

•

Try a new channel, if OK, then possible station trouble.

Lines or Streaks in Picture

•

If outside antenna is being used, check for broken wire.

•

Check for local interference.

No Color

•

Try a new channel, if OK, then possible station trouble.

•

Is antenna connected to jack on the back of the set?

•

If outside antenna is being used, check for broken wire.

•

Adjust “COLOR” control.

Poor Reception on Some Channels

•

Try a new channel, if OK, then possible station trouble.

Ghosts in Picture

•

Is antenna connected to jack on the back of the set?

•

If outside antenna is being used, check for broken wire.

•

Check for local interference.

Weak Picture

•

Try a new channel, if OK, then possible station trouble.

•

Is antenna connected to jack on the back of the set?

•

If outside antenna is being used, check for broken wire.

•

Adjust “CONTRAST” & “BRIGHT” control.

Sound OK, Picture Poor

•

Try a new channel, if OK, then possible station trouble.

•

Is antenna connected to jack on the back of the set?

•

If outside antenna is being used, check for broken wire.

•

Check for local interference.

•

Adjust “CONTRAST” & “BRIGHT” control.

If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-

sulting the following checklist.

PROBLEM CORRECTIVE ACTION

No power

•

Make sure the power plug is connected to an AC outlet.

•

Make sure the power is turned on.

No operation by infrared remote

•

Check if the power plug is connected to an AC outlet.

control

•

Check the batteries in the remote control.

•

Aim the remote control directly at the remote sensor. If necessary,

remove all the obstacles between the sensor and the remote control.

•

You have to be within 23 feet of the unit.

•

Check if the correct mode is selected. If not switch the mode by

hitting [SELECT], whichever you need.

- 47 - EN

CLOSED CAPTION PROBLEM POSSIBLE REMEDY

Misspelling in captions

•

Error committed by the closed captioning production company.

•

Possible in a live broadcast. Not in case of a prerecorded program.

Text is not shown in its entirety or

•

A few seconds of delay is common for live broadcast.

a delay occurs from what is being

•

Display capacity may not exceed 220 words per minute. If a dialogue

said

•

exceeds that rate, selective editing is used to insure that the captions

•

remain up-to-date with the current TV screen dialogue.

Captions scrambled with white

•

Caused by interferences of building, power lines, thunderstorms, etc.

boxes

No captions in a program which

•

The broadcast may use a time compression process to speed up the

must contain closed caption

•

program. The decoder cannot read the compressed information and

• captions will be lost.

No captions in a prerecorded

•

Possibility of a illegal copy or an erroneous copying process

videotape which indicated closed

•

accidentally performed by the fabricator.

captions included.

Black box in the TV screen

•

You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or

•

Caption “OFF”.

PROBLEM CORRECTIVE ACTION

Picture OK, Sound Poor

•

Try a new channel, if OK, then possible station trouble.

•

Check for local interference.

Timer recording is not possible

•

Make sure the timer recording is set correctly.

•

Make sure the power is off.

•

Make sure the unit’s clock is set correctly.

Cannot go into the recording mode

•

Make sure the tape has an erase-prevention tab. If need, cover the

•

hole with plastic tape.

Playback picture is partially noisy

•

Adjust tracking control for a better picture using

[CHANNEL K / L]

•

on the unit.

No picture but the audio is OK in

•

Head cleaning may be necessary. Refer to “AUTO HEAD

playback • CLEANING” on page 49.

No operation by infrared remote

•

Make sure the AC cord is connected to an AC outlet.

control

•

Check batteries in remote control.

Video or color fades in and out

•

You can not copy a copyrighted video tape. You are experiencing

when making a copy of a video tape

•

copy guard protection.

Different color marks on screen

•

Magnetism from nearby appliances and geomagnetism might affect

the color of the TV picture. Move the unit away from the appliances,

the unit can repair itself automatically. If you want to repair immedi-

ately,

unplug the power cord, then plug it in again 30 minutes later or

so. This automatically resets the unit.

- 48 - EN

NOTES:

•

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

PROBLEM CORRECTIVE ACTION

No picture

•

Insert a correct video disc that plays on this unit.

•

Hit [SELECT] to select DVD mode, then try other DVD feature.

Disc cannot be played

•

Insert the disc.

•

Clean the disc.

•

Place the disc correctly, with the label side up.

•

Cancel the parental lock or change the control level.

No sound

•

Connect the audio cables firmly.

•

Turn the power of the audio component on.

•

Correct the audio output settings.

•

Correct the input settings on the audio component.

No DTS audio is output

•

This unit does not support DTS audio. This is not a malfunction.

Distorted picture

•

There are some cases where pictures may be slightly distorted,

which are not a sign of a malfunction.

•

Although pictures may stop for a moment, this is not a malfunction.

Audio or subtitle language

•

The selected language is not available for audio or subtitles on the

does not match the set up

•

DVD. (This is not a malfunction.)

The camera angle cannot be changed

•

The DVD does not contain sequences recorded from different

camera angles. (This is not a malfunction.)

Audio or subtitle language cannot be

•

The DVD does not contain audio source or subtitles in the selected

changed

•

language. (This is not a malfunction.)

“Prohibited icon” appears on the

•

That operation is prohibited by the unit or the disc.

screen, prohibiting an operation

•

¡(This is not a malfunction.)

CD sound dropout

•

Scratched disc. Replace the disc with an unscratched one.

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

DVD Mode

- 49 - EN

CABINET CLEANING

•

Wipe the front panel and other exterior surfaces of

the unit with a soft cloth immersed in lukewarm

water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

ticide liquid near the unit. Such chemicals may

cause damage and discoloration to the exposed sur-

faces.

AUTO HEAD CLEANING

•

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clearer picture.

•

Playback picture may become blurred or interrupt-

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

back, the video heads in your unit may need to be

cleaned.

1.Please visit your local Audio/Video store and pur-

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line mentioned on the

front page, to locate an Authorized Service Center.

NOTES:

•

Remember to read the instructions included with

the video head cleaner before use.

•

Clean video heads only when problems occur.

SERVICING

•

Should your unit become inoperative, do not try to

correct the problem by yourself. There are no user-

serviceable parts inside. Turn off, unplug the power

cord and

please call our help line mentioned on

the front page, to locate an Authorized Service

Center.

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

•

If the unit still does not perform properly when it is operated, while referring to the relevant sections and to

“TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty.

Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup

unit.

•

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

•

Always store the disc in its protective case when it

is not used.

DISC HANDLING

•

To clean-off, use a soft cloth.

•

Do not use a hard cloth since this will mar the disc.

•

Wipe the disc in a straight line from center to edge.

•

Never wipe with a circular motion.

•

Do not use detergent or abrasive cleaning agents.

MAINTENANCE

- 50 - EN

Product type: DVD Player

Discs: DVD video, Audio CD

Output signal format: NTSC color

•

Designs and specifications are subject to change without notice.

•

If there is a discrepancy between languages, the default language will be English.

DVD

GENERAL SPECIFICATIONS

SPECIFICATIONS

CRT: 24 inch in-line gun,

90˚ deflection tube

Television system: NTSC-M

Closed caption system: §15.119/FCC

Video Heads: Rotary four-head

Tape width: 1/2 inch

Tape speed

SP: 33.40mm/sec.

LP: 16.67mm/sec.

SLP: 11.12mm/sec.

Tuner channel

TV VHF Low: #2~#6

TV VHF High: #7~#13

TV UHF: #14~#69

CATV

VHF: 5A

MID band: A5~A1, A~I

SUPER band: J~W

HYPER band: W+1~W+84

TV/VCR

ELECTRICAL SPECIFICATIONS

Sound output: 2 speakers, 1W, 8 ohm

OTHER SPECIFICATIONS

Terminals

Antenna input: VHF/UHF/CATV

75 ohm unbalanced (F-type)

Video input: RCA connector [ 1

Audio L/R input: RCA connector [ 2

Headphone: 1/8” stereo (3.5 mm)

Coaxial digital

audio output: One pin jack,

500m Vpp (75 ohm)

Remote control: Digital encoded

infrared light system

Operating

temperature: 5°C to 40°C

(41°F~104°F)

Power requirements: AC 120V, 60Hz

Power consumption

(Maximum): 120W

Picture tube: 24" PF

Dimensions: H : 22-11/16" (576mm)

W: 24-1/8" (612mm)

D: 19" (482.2mm)

Weight: 66.1 lbs. (30kg)

- 51 - ES

INDICE

■ INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

■ CONTROLES DE OPERACIÓN Y FUNCIONES. . . . . 51

PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 52

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 52

CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 52

CONEXIÓN A TOMAS DE ENTRADA DELANTERAS 53

CONEXIÓN A UN AMPLIFICADOR ESTÉREO

EQUIPADO CON TOMAS DE ENTRADA DIGITAL.

(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL

(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

SECCIÓN DE TV/VCR

■ FUNCIONES Y AJUSTES DE TV. . . . . . . . . . . . . . . . . 54

PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 54

IDIOMA DEL MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

■ GRABACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

GRABACIÓN NORMAL . . . . . . . . . . . . . . . . . . . . . . . . 55

SECCIÓN DE DVD

REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55

MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

CONTROLES DE

OPERACIÓN Y FUNCIONES

• Consulte la figura 1 de la página 9 para el

panel frontal de la unidad

• Consulte la figura 2 de la página 9 para el

mando a distancia

• Consulte la figura 3 de la página 10 para la

vista posterior

1. Botón POWER

Presione para encender y apagar la unidad.

2. Botones VOLUME (VOL.) K / L

Presione para controlar el nivel de volumen del DVD y

el televisor.

3. Botones SKIP H / G (para DVD)

Presione una vez para omitir capítulos o pistas y

desplazarse a un punto específico.

Botones SEARCH E / D (para DVD)

Mantenga el botón presionado para cambiar la

velocidad de reproducción en avance o retroceso.

4. Botón B PLAY

Inicia la reproducción del contenido del disco o cinta.

5. Botón C STOP

(Panel frontal) Detiene la operación del disco.

(Mando a distancia) Detiene la operación del disco o el

casete.

6. Botón A OPEN/CLOSE

Presione para insertar un disco en la bandeja o retirarlo

de ella.

7. Bandeja de carga del disco

8. Indicador DVD

Se ilumina durante el modo DVD.

9. Botón SELECT

Presione para cambiar al modo TV/VCR, modo de

entrada externa o modo de DVD. El modo

seleccionado (TV/VCR o DVD) se visualiza en el

indicador del panel delantero.

10. Indicador TV/VCR

Se ilumina durante el modo TV/VCR.

11. Botones CHANNEL (CH.) K / L

Utilice para seleccionar canales memorizados.

12. Indicador de grabación

Parpadea durante la grabación. Se ilumina durante el

modo de espera de grabación controlada por

temporizador.

13. Botón REC/OTR (Panel frontal)

Presione para empezar la grabación manual. Presione

repetidamente para empezar la grabación instantánea (OTR).

Botón RECORD (Mando a distancia)

Presione para empezar la grabación manual.

14. Botón E REW (para TV/VCR)

Presione para rebobinar la cinta o para ver la imagen

rápidamente en dirección de retroceso durante el modo

de reproducción. (Búsqueda en dirección de retroceso)

15. Botón F.FWD D (para TV/VCR)

Presione para adelantar rápidamente la cinta o para ver la

imagen rápidamente en dirección de avance durante el modo

de reproducción. (Búsqueda en dirección de avance)

16. Botón C / A STOP/EJECT

Presione para detener la cinta. Presione en el modo de

parada para retirar la cinta de la unidad.

17. Ventanilla del sensor de mando a distancia

18. Toma HEADPHONE

Para conectar auriculares (no suministrados) y escuchar

en privado.

19. Toma de entrada VIDEO

Conecte aquí la toma de salida de video de una

videocámara o de una videograbadora.

20. Tomas de entrada AUDIO L/R

Conecte aquí las tomas de salida de audio de una

videocámara o de una videograbadora.

21. Compartimiento del cassette

22. Botón PICTURE

Presione para ajustar la imagen.

23. Botones numéricos

Modo TV/VCR:

Presione dos cifras para acceder directamente al canal deseado.

No olvide presionar [0] antes de elegir un canal de una sola cifra.

Botón +100

Presione para seleccionar canales de televisión por

cable cuyo número sea superior a 99.

Modo DVD:

Presione para introducir el número deseado.

Botón +10

Presione para introducir números superiors a 9.

24. Botón PAUSE F

Hace una pausa en la reproducción del disco o cinta.

25. Botón SPEED

Presione para seleccionar la velocidad de grabación

deseada: SP/SLP.

26. Botón C.RESET

Presione para poner el contador en 0:00:00.

Presione también para cancelar un ajuste de programa

de temporizador.

27. Botón DISPLAY

Modo TV/VCR:

Indica el contador o el número del canal y la fecha

actual en la pantalla del televisor.

Modo DVD:

Indica el estado actual en la pantalla del televisor.

28. Botón SETUP

Presione para entrar o salir del menú de configración

de televisor o DVD.

29. Botón TITLE

Para visualizar el menú de títulos.

30. Botón CLEAR

Presione para cancelar o borrar un ajuste entrado

actualmente.

31. Botón MODE

Presione para llamar la pantalla de la reproducción

programada o la de reproducción aleatoria en el modo

de parada.

Presione para llamar la pantalla de ajuste del nivel del

negro o la pantalla de sonido ambiental durante la

reproducción.

- 52 - ES

1) Abra la cubierta del compartimiento de las pilas

empujando la cubierta del mando a

distancia en el sentido de la flecha.

2) Inserte 2 pilas “AA” en el

compartimiento de las pilas, en el

sentido indicado por las marcas de polaridad (+/-).

3) Vuelva a poner la cubierta.

PARA INSERTAR LAS PILAS

NOTA:

Antes de enchufar la antena a la toma ANT. de la

unidad, compruebe que la clavija no esté doblada.

Si esta doblada, póngala derecha como se muestra

en la ilustración, y luego conéctela en la toma

ANT. de la unidad.

32. Botón SEARCH MODE

Presione para localizar un punto deseado.

33. Botón AUDIO

Modo TV/VCR

Presione para seleccionar el modo de sonido deseado cuando

vea un programa de TV o reproduzca o grabe un casete.

Modo DVD:

Presione para seleccionar un modo de sonido o idioma

de audio deseado.

34. Botón SUBTITLE

Presione para seleccionar el idioma de subtítulos

deseado.

35. Botón REPEAT

Repite la reproducción del disco, título, capítulo o pista

actual.

36. Botón ANGLE

Presione para cambiar el ángulo de la cámara y ver la

secuencia que se está reproduciendo desde un ángulo

diferente (si existe).

37. Botón A-B (modo DVD)

Repite la reproducción de una sección seleccionada.

38. Botón RETURN

Permite volver a la pantalla anterior en el menú de

configuración.

39. Botón ENTER

Presione para establecer un ajuste.

40. Botones K / L / { / B

Modo TV/VCR:

Presione para seleccionar un modo de ajuste en el

menú que aparece en la pantalla del televisor.

Presione también para seleccionar o establecer ajustes

en un menú en particular.

Modo DVD:

Presione para hacer una selección en el menú.

41. Botón DISC MENU

Muestra menú del DVD.

42. Botón ZOOM

Amplía parte de la imagen reproducida de un DVD.

43. Botón MUTE

Suprime la salida de sonido. Presione de nuevo para

restablecer el sonido.

44. Botón SLEEP

Utilice para ajustar el temporizador de dormir.

45. Toma ANT.

Conecte a una antena, sistema de televisión por cable o

sistema de satélite.

46. Cable de alimentación

Conecte a un toma de CA estándar (120 V/60 Hz).

NOTA:

•

Antes de conectar el cable de alimentación de una toma

de CA estándar, retírelo del gancho para evitar dañarlo.

47. Toma AUDIO OUT COAXIAL

Conecte solamente a la entrada digital de un

amplificador externo o decodificador (para audio de

DVD solamente).

PREPARACIÓN PARA LA

UTILIZACIÓN

CONEXIONES DE ANTENA/CABLE

Nota para el instalador de sistemas CATV

Esta nota tiene la finalidad de llamar la atención

del instalador de sistemas CATV para que tenga

en cuenta el Artículo 820-40 de la NEC, que

proporciona recomendaciones para hacer una

conexión a tierra apropiada y, en particular,

especifica que la tierra del cable debe conectarse

al sistema de puesta a tierra del edificio, tan cerca

del punto de entrada del cable como sea posible.

Consulte la figura 4 de la página 12

(Necesita enderezarse)

(Clavija derecha)

ANTENA COMBINADA DE VHF/UHF

La antena combinada de VHF/UHF de 75 ohmios puede

conectarse a la toma ANT.

ANTENAS SEPARADAS DE VHF/UHF

En algunas zonas será necesario utilizar una antena exterior.

TELEVISIÓN POR CABLE SIN CAJA DE

CONVERTIDOR/DECODIFICADOR

Utilice esta conexión si su sistema de televisión por

cable se conecta directamente a la unidad, sin una

caja de convertidor.

TELEVISIÓN POR CABLE CON CAJA

DE CONVERTIDOR/DECODIFICADOR

O CAJA DE SATÉLITE

Si su compañía de televisión por cable le suministra

una caja de convertidor o si utiliza un sistema de

satélite, podrá utilizar la conexión básica que se

muestra en la ilustración.

La selección de los canales deberá hacerse con la caja de

convertidor o con la caja de satélite. Esto significa que

no es posible cambiar de canal utilizando el mando a

distancia de la unidad.

Clavija doblada

Cable

Clavija

NOTA:

•

Para su seguridad y para evitar que se dañe

la unidad, desenchufe el cable de antena de la

toma ANT. antes de mover la unidad.

- 53 - ES

CONEXIÓN A UN DECODIFICADOR

DOLBY DIGITAL (para DVD)

Si utiliza esta unidad para reproducir un disco DVD

grabado en formato de sonido envolvente Dolby

Digital de 5,1 canales, la unidad emitirá un flujo de

datos DOLBY DIGITAL desde su toma AUDIO

OUT COAXIAL. Si conecta la unidad a un

decodificador Dolby Digital, podrá disfrutar de una

tonalidad más convincente y real, con un sonido

envolvente potente y de alta calidad similar al de los

cines.

Utilice cables digitales coaxiales de audio

(disponibles en el comercio) para hacer las

conexiones de audio.

NOTAS:

•

Asegúrese de apagar todos los componentes del

sistema antes de conectar otro componente.

•

Consulte los manuales de instrucciones de los

componentes que va a conectar a la unidad.

•

Si conecta un decodificador Dolby Digital, ajuste

la función “DOLBY DIGITAL” a “BITSTREAM”

para salida de audio en el modo de configuración.

•

A menos que se haga la conexión a un

decodificador Dolby Digital, ajuste la función

“DOLBY DIGITAL” a “PCM” para salida de

audio en el modo de configuración. La

reproducción en una unidad utilizando ajustes

incorrectos puede generar ruido y distorsión, y

también puede provocar daños a los altavoces.

Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo de la

doble D son marcas comerciales de Dolby

Laboratories.

CONEXIÓN A UN AMPLIFICADOR

ESTÉREO EQUIPADO CON TOMAS

DE ENTRADA DIGITAL (para DVD)

Utilice un cable digital coaxial de audio (disponible en

el comercio) para hacer las conexiones de audio.

Conexión a un amplificador equipado con tomas de

entrada digital, platina MD o platina DAT.

NOTAS:

• La fuente de audio de un disco grabado en formato

de sonido envolvente Dolby Digital de 5,1 canales

no se puede grabar como sonido digital mediante

una platina MD o DAT.

•

Asegúrese de apagar todos los componentes del

sistema antes de conectar otro componente.

• Consulte los manuales de instrucciones de los

componentes que va a conectar a la unidad.

• Ajuste la función “DOLBY DIGITAL” a “PCM”

para salida de audio en el modo de configuración.

La reproducción en una unidad utilizando ajustes

incorrectos puede generar ruido y distorsión, y

también puede provocar daños a los altavoces.

Consulte la figura 6 de la página 13

Consulte la figura 7 de la página 14

CONEXIÓN A TOMAS DE

ENTRADA DELANTERAS

Cuando vea un programa grabado en otra fuente

(videograbadora o videocámara), utilice las tomas de

entrada AUDIO/VIDEO de la parte delantera de la

unidad.

Conecte las tomas de salida de audio/vídeo de otra

fuente a las tomas AUDIO L/R y VIDEO de esta

unidad.

Después, presione [SELECT] o [CH.

] hasta

que aparezca “AUX” en la pantalla.

NOTA:

•

Cuando conecte una videograbadora monofónica

(otra fuente) a esta unidad, conecte la toma de

salida de audio de la videograbadora monofónica

(otra fuente) a la toma AUDIO L de esta unidad. El

audio saldrá igualmente por los canales izquierdo y

derecho.

Consulte la figura 5 de la página 13

- 54 - ES

1 Seleccione “LANGUAGE”

Presione [SETUP].

Presione

[K / L] para apuntar a “LANGUAGE”.

2 Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS”

Presione [ENTER] repetidamente para seleccionar

“ENGLISH” = inglés, “ESPAÑOL” o

“FRANÇAIS” = francés.

3 Salga del modo de idioma

Presione [SETUP] para salir del menú.

NOTAS:

•

Esta función afecta sólo el idioma en el menú de la

pantalla y no la fuente de audio.

•

Si por alguna razón, el menú está en francés,

presione [SETUP], presione [K / L] para apuntar

al “LANGAGE [FRANÇAIS]” y presione

[ENTER] repetidamente para seleccionar el

idioma deseado y presione [SETUP].

IDIOMA DEL MENÚ

TV/VCR

FUNCIONES Y AJUSTES

DE TV

1 Enchufe el cable eléctrico

Enchufe el cable eléctrico de la unidad en un

tomacorriente de CA del hogar.

NOTA:

•

Si aparecen números en la esquina de la pantalla,

presione [POWER] sin desenchufar el cable

eléctrico.

2 Encienda la unidad

Presione [POWER] para encender la unidad.

3 Seleccione el número de canal

Presione [CH. K / L] o los botones numéricos para

seleccionar su número de canal deseado.

Nota para el uso de los botones numéricos:

¡Debe colocar un cero antes de los números de canal

de una sola cifra (por ejemplo: 02, 03, 04, etc.).

Cuando seleccione canales de cable de más de 99,

presione primero [+100] y después las dos últimas

cifras. (Ejemplo: para seleccionar el canal 125,

primero presione [+100] y después presione [2] y [5].)

4 Ajuste el sonido

Presione [VOL.

] para ajustar el volumen.

Presione

[MUTE] para silenciar instantáneamente el

sonido.

Presione nuevamente para recuperar el nivel de

sonido anterior.

NOTA:

•

Si presiona [CH. K / L] en el modo DVD, puede

cambiar los canales de TV. Incluso si apaga la

unidad en el modo DVD, cuando vuelva a

encender, volverá al modo TV/VCR.

PARA VER CANALES DE CABLE O

SATELITE

•

Si la unidad está conectada a una caja de cable o

caja de satélite, presione [CH. K / L] para

seleccionar CH3 o CH4 de acuerdo con el ajuste

de canal de salida del dispositivo y seleccione el

canal deseado en el dispositivo.

PARA VER UNA ENTRADA EXTERNA

•

Cuando se conecta un equipo externo en las tomas

de entrada AUDIO/VIDEO frontales, presione

[SELECT] o [CH. K / L] repetidamente hasta que

aparezca “AUX” en la pantalla.

SECCIÓN DE TV/VCR

PARA MIRAR UN PROGRAMA DE TV

TV/VCR

AJUSTE MANUAL DEL RELOJ

Asegúrese ...

•

La unidad debe estar encendida.

En el siguiente ejemplo, el reloj debe estar en:

FECHA 6 de mayo, 2005

HORA DE AJUSTE 5:40PM

1 Seleccione “AJUSTE RELOJ”

Presione [SETUP].

Presione

[K / L]

para seleccionar “AJUSTE RELOJ”

y presione [ENTER].

2 Seleccione “AJUSTE MANUAL RELOJ”

Presione

[K / L]

para seleccionar “AJUSTE

MANUAL RELOJ” y presione [ENTER].

3 Seleccione el mes

Presione

[K / L]

hasta que aparezca el mes deseado.

(Ejemplo: Mayo

→ “05”)

Presione

[B]. (O presione [s] para volver un paso.)

4 Seleccione el día

Presione

[K / L]

hasta que aparezca el día deseado.

(Ejemplo: 6

º → “06”)

Presione

[B].

AJUSTE DEL RELOJ

TV/VCR

- 55 - ES

SECCIÓN DE DVD

REPRODUCCIÓN BÁSICA

Para empezar

¡Conecte la alimentación del amplificador y otros

componentes, si es necesario.

1 Presione [POWER].

¡La alimentación se conectará.

2 Presione [A OPEN/CLOSE] para abrir la

bandeja de carga del disco.

3 Ponga el disco deseado en la bandeja, con

la etiqueta hacia arriba.

4 Presione [PLAY O].

La bandeja se cerrará automáticamente y la reproducción

comenzará desde el primer capítulo o pista del disco.

¡La reproducción también empieza cerrando

manualmente la bandeja del disco o presionando

[A OPEN/CLOSE].

¡Si la reproducción no comienza automáticamente,

presione

[

PLAY O

]

Cuando reproduzca un DVD que tenga grabado un

menú de títulos, el menú podrá aparecer en la pantalla.

Presione [STOP

] para detener la reproducción.

DVD-V

5 Seleccione el año

Presione [K / L] hasta que aparezca el año deseado.

(Ejemplo: “2005”)

Presione

[B].

6 Seleccione la hora

Presione [K / L] hasta que aparezca la hora deseada.

(Ejemplo: “5”, “PM”)

Presione

[B].

7 Seleccione los minutos

Presione [K / L] hasta que aparezcan los minutos

deseados.

(Ejemplo: “40”)

8 Haga funcionar el reloj

Presione [SETUP].

Aunque no aparezcan los segundos, empezará a

contar desde 00 cuando presione

[SETUP]. Utilice

esta característica para sincronizar el reloj con la hora

real.

GRABACIÓN

SOLO puede ver el mismo programa que se está

grabando.

1 Seleccione el canal a grabar

Presione los botones numéricos o [CH. K / L].

NOTA:

•

Si la unidad está conectada a una caja de cable o

caja de satélite, la unidad debe estar en CH3 o

CH4 y debe seleccionarse el canal a grabar en la

caja de cable o caja de satélite.

2 Seleccione la velocidad de la cinta

Presione [SPEED] para seleccionar la velocidad de

cinta deseada (SP/SLP).

3 Empiece a grabar

Presione [RECORD].

4 Pare la grabación

Presione [STOP C].

TV/VCR

GRABACIÓN NORMAL

MENÚ DE DISCO

1 Presione [DISC MENU].

¡Aparecerá el menú principal de DVD.

¡Si no existe la función, puede aparecer el símbolo

en la pantalla de TV.

¡Si el menú de disco existe en el disco, aparecerán el

idioma de audio, opciones de subtítulo, capítulos

para el título y otras opciones para su selección.

2 Presione [K / L / s / B] para seleccionar

un ítem y presione [ENTER] para confirmar

la selección.

DVD-V

REANUDACIÓN

1 Durante la reproducción, presione

[STOP

C].

Aparecerá el mensaje de continuación en la pantalla de TV.

2 Presione [PLAY O], la reproducción continuará

desde el punto donde se paró la reproducción.

¡Para cancelar la continuación, presione dos veces

[STOP C].

¡La información de continuación permanece activada

incluso cuando apaga el interruptor principal.

DVD-V

Printed in Malaysia 1EMN20315

T2127UH ★★★★★

FUNAI CORPORATION

LIMITED WARRANTY

FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship

as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this

warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date

of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail

purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does

not apply to any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE

PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN

THE UNIT IS CARRIED-IN TO A FUNAI AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest FUNAI Authorized Service Center or for general service inquiries, please

call or write to the following:

FUNAI CORPORATION, INC.

SERVICE CENTER

19900 Van Ness Avenue, Torrance, CA 90501

Tel :1-800-242-7158

http://www.Symphonic.us

Head Office: 100 North Street, Teterboro, NJ 07608

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Symphonic MSD724F Manual de usuario

Marca: Symphonic

Modelo: MSD724F

Categoría: Reproductores de casete

Tipo: Manual de usuario

Este manual también es adecuado para

Descargar PDF

informe

En otros idiomas

English: Symphonic MSD724F User manual

Symphonic MSD724F Manual de usuario

Este manual también es adecuado para

Symphonic MSD724F Manual de usuario

En otros idiomas

Documentos relacionados

Otros documentos