Holmes HLH4422M Manual de usuario

Categoría
Calentadores espaciales
Tipo
Manual de usuario

Este manual también es adecuado para

TROUBLESHOOTING
DIAGNOSTICO DE PROBLEMAS
© 2013 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved.
Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.
158248 Rev. A HLH4422M_13ESM1 Impreso en China
GCDS-HOL28159-JC
Printed In China
Troubleshooting for your Heater
Trouble Probable Cause Solution
• Heater
Does Not
Turn On.
Tip-over switch engaged.
Manual user reset is activated.
Not plugged in properly.
Electrical outlet does not hold plug
in securely.
Thermostat set too low.
Obstruction causing the heater not
to operate.
Circuit breaker trips.
Set heater upright on a level surface.
Follow reset instructions listed in this manual.
Ensure plug is properly inserted. Make sure
electrical outlet and circuit breaker are working.
Have outlet replaced by a licensed electrician.
Turn the Thermostat Control to the highest setting.
Unplug the heater and remove all obstructions.
Position your heater 36 inches (91cm) away from
all objects.
Make sure no other high wattage appliances are
operating on the same circuit and reset breaker if
needed.
Not Enough
Heat.
Heater is in Low Heat setting.
Thermostat set to low.
Change setting to High Heat.
Turn Thermostat Control to the highest setting
until the heater restarts.
Heater
Cycles ON
and OFF
Frequently.
The thermostat automatically turns
the heater on and off to maintain
selected comfort level.
To make this occur less frequently adjust the
thermostat control to the highest setting.
Fan Speed
Doesn't
Change.
High Heat and Low Heat settings
control the heat output of the
heater and not the fan speed. Fan
runs at the same speed on all
settings.
Run heater in High Heat for maximum heat
output.
Unexpected
Noise.
You may hear a popping or
crackling sound as the heater heats
up. This is normal and safe
operation. Once the heater heats up,
the crackling sound will go away.
If the noise persists, visit our website
at www.holmesproducts.com.
Unexpected
Smell.
There may be an odor or vapor
coming from the heater the first
time you use it or after prolonged
or seasonal storage.
This is normal and is the result of dust or other
debris accumulating on the heating element.
Make sure the heater is in a well ventilated area
and continue running until the odor or vapor goes
away.
Solución de problemas del calefactor
Problema Posible Causa Solución
• Elcalefactor
no
enciende.
El interruptor contra inclinaciones
está activado.
El restablecimiento manual de
usuario está activado.
No está conectado correctamente.
El tomacorriente no sostiene el
enchufe de manera segura.
El termostato está en un valor
demasiado bajo.
Hay obstrucciones que hacen que el
calefactor no funcione.
El interruptor de circuito está
desactivado.
Coloque el calefactor en posición vertical sobre
una superficie nivelada.
Siga las instrucciones de restablecimiento que
aparecen en este manual.
Compruebe que el enchufe esté insertado
correctamente. Asegúrese de que el tomacorriente
y el interruptor de circuito funcionen.
Contrate a un eléctrico con licencia para
reemplazar el tomacorriente.
Gire el control de termostato al valor más alto.
Desconecte el calefactor y retire las obstrucciones.
Coloque el calefactor a 91 cm de distancia de los
demás objetos.
Compruebe que no haya otros aparatos de alto
vataje funcionando en el mismo circuito y, si es
necesario, restablezca el interruptor.
No hay
suficiente
calefacción.
El calefactor está en la posición de
calor bajo.
El termostato está en un valor bajo.
Cambie el valor a Calor alto.
Gire el control de termostato al valor más alto
hasta que el calefactor reinicie.
El calefactor
se enciende
y apaga con
frecuencia.
El termostato automáticamente enciende
y apaga el calefactor a fin de mantener
el nivel de confort seleccionado.
Para hacer que este cambio ocurra con menos
frecuencia, gire el control de termostato al valor
más alto.
La velocidad
del
ventilador
no cambia.
Los valores de Calor alto y Calor
bajo controlan la salida de calor del
calefactor y no la velocidad del
ventilador. El ventilador funciona a
la misma velocidad en todas las
opciones.
Utilice el valor Calor alto del calefactor para
obtener la máxima calefacción.
Ruido
inesperado.
Es posible que se escuchen
chasquidos o crujidos cuando el
calefactor se calienta. Esto es parte
del funcionamiento normal y
seguro. Una vez que el calefactor
se caliente, los crujidos cesarán.
Si el ruido persiste, póngase visite nuestro sitio
web www.holmesproducts.com.
Olor
inesperado.
Es posible que el calefactor
produzca olores o vapores la
primera vez que lo utilice o después
de haber estado almacenado una
temporada.
Esto es normal y es el resultado del polvo u otros
residuos que se acumulan en el dispositivo de
calefacción. Asegúrese de que el calefactor se
encuentre en un área ventilada y que siga
funcionando hasta que el olor o vapor desaparezcan.
1 YEAR LIMITED WARRANTY
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited
doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of one year from the date of
purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair or replace this
product or any component of the product found to be defective during the warranty period. Replacement will be made with a
new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar
product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or
mechanical functions on this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the
original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service centers, or retail
stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or
misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly,
repair or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not
cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or
statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for
a particular purpose is limited in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use
the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of
contract, fundamental or otherwise, or for any claim brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages
or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from province to province,
state to state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
In the U.S.A.
If you have any question regarding this warranty or would like to obtain warranty service, visit our website
at www.holmesproducts.com.
In Canada
If you have any question regarding this warranty or would like to obtain warranty service, visit our website
at www.holmesproducts.com.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located
in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing
business as Jarden Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any
other problem or claim in connection with this product, please write our Consumer Service Department. PLEASE DO
NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
GARANTÍA LIMITADA DE 1 AÑO
Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions, o en Canadá, Sunbeam Corporation
(Canada) Limited operando bajo el nombre de Jarden Consumer Solutions, (en forma conjunta, “JCS”), garantiza que por
un período de uno año a partir de la fecha de compra, este producto estará libre de defectos de materiales y mano de obra.
JCS, a su elección, reparará o reemplazará este producto o cualquier componente del mismo que presente defectos durante
el período de garantía. El reemplazo se realizará por un producto o componente nuevo o reparado. Si el producto ya no
estuviera disponible, se lo reemplazará por un producto similar de valor igual o superior. Ésta es su garantía exclusiva. No
intente reparar o ajustar ninguna función eléctrica o mecánica de este producto. Al hacerlo elimínará ésta garantía.
La garantía es válida para el comprador minorista original a partir de la fecha de compra inicial y la misma no es
transferible. Conserve el recibo de compra original. Para solicitar servicio en garantía se requiere presentar un recibo
de compra. Los agentes y centros de servicio de JCS o las tiendas minoristas que venden productos de JCS no tienen
derecho a alterar, modificar ni cambiar de ningún otro modo los términos y las condiciones de esta garantía.
Esta garantía no cubre el desgaste normal de las piezas ni los daños que se produzcan como resultado de uso negligente o
mal uso del producto, uso de voltaje incorrecto o corriente inapropiada, uso contrario a las instrucciones operativas, y
desarme, reparación o alteración por parte de un tercero ajeno a JCS o a un Centro de Servicio autorizado por JCS.
Asimismo, la garantía no cubre actos fortuitos tales como incendios, inundaciones, huracanes y tornados.
¿Cuál es el límite de responsabilidad de JCS?
JCS no será responsable de daños incidentales o emergentes causados por el incumplimiento de alguna garantía o
condición expresa, implícita o legal.
Excepto en la medida en que lo prohíba la ley aplicable, cualquier garantía o condición implícita de comerciabilidad o
aptitud para un fin determinado se limita, en cuanto a su duración, al plazo de la garantía antes mencionada.
JCS queda exenta de toda otra garantías, condiciones o manifestaciones, expresa, implícita, legal o de cualquier otra naturaleza.
JCS no será responsable de ningún tipo de daño que resulte de la compra, uso o mal uso del producto, o por la
imposibilidad de usar el producto, incluidos los daños incidentales, especiales, emergentes o similares, o la pérdida de
ganancias, ni de ningún incumplimiento contractual, sea de una obligación esencial o de otra naturaleza, ni de ningún
reclamo iniciado contra el comprador por un tercero.
Algunas provincias, estados o jurisdicciones no permiten la exclusión o limitación de los daños incidentales o
emergentes ni las limitaciones a la duración de las garantías implícitas, de modo que es posible que la exclusión o las
limitaciones antes mencionadas no se apliquen en su caso.
Esta garantía le otorga derechos legales específicos y es posible que usted tenga otros derechos que varían de un
estado, provincia o jurisdicción a otro.
Cómo solicitar el servicio en garantía
En los Estados Unidos
Si tiene alguna pregunta sobre esta garantía o desea recibir servicio de garantía, póngase visite nuestro sitio web
www.holmesproducts.com.
En Canadá
Si tiene alguna pregunta sobre esta garantía o desea recibir servicio de garantía, póngase visite nuestro sitio web
www.holmesproducts.com.
En los Estados Unidos, esta garantía es ofrecida por Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer
Solutions, Boca Ratón, Florida 33431. En Canadá, esta garantía es ofrecida por Sunbeam Corporation (Canada) Limited
operando bajo el nombre de Jarden Consumer Solutions, 20 B Hereford Street, Brampton, Ontario L6Y 0M1. Si usted tiene otro
problema o reclamo en conexión con este producto, por favor escriba al Departamento de Servicio al Consumidor. POR FAVOR
NO DEVUELVA ESTE PRODUCTO A NINGUNA DE ESTAS DIRECCIONES NI AL LUGAR DE COMPRA.
WARRANTY INFORMATION
INFORMACION DE LA GARANTIA
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
LEA Y CONSERVE ESTAS IMPORTANTES INSTRUCCIONES
Owner’s Guide
HLH4422M
Guía del usuario
http://www.holmesproducts.com/HOLCLG201
http://www.holmesproducts.com/HOLCLG201
to receive a FREE GIFT OR PROMO CODE*.
It’s our “thanks” to you for being a Holmes
®
brand customer.
para recibir un OBSEQUIO GRATIS O UN CÓDIGO DE
PROMOCIÓN*. Es nuestra manera de decirle “gracias” por ser
cliente de la marca Holmes
®
.
GO ONLINE NOW to
INGRESE AHORA MISMO al sitio
-You will also get access to special sale items
& promotions on a full assortment of Holmes
®
branded products.
-También obtendrá acceso a promociones y
artículos de venta especiales de una completa
variedad de productos de la marca Holmes
®
.
*While supplies last; subject to availability.
*Hasta agotar el stock; sujeto a disponibilidad
HURRY & SIGN UP TODAY!
¡APRESÚRESE Y REGÍSTRESE HOY MISMO!
Holmes
®
Heater
Holmes
®
Calefactor
© 2013 Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions. Todos los derechos reservados.
Distribuido por Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions, Boca Raton, Florida 33431.
HLH4422M_13ESM1.indd 1 1/17/13 10:36 AM
NOTE: It is normal for the heater to cycle ON and OFF as
it maintains the preset temperature. To prevent the unit
from cycling, turn the thermostat control to the highest
setting (9).
CAUTION: FRONT GRILL IS HOT WHEN UNIT IS IN
OPERATION.
CLEANING/MAINTENANCE
Always unplug the heater before cleaning and allow the
heater to cool down.
1. Clean the unit with a soft cloth moistened with a mild
soap solution.
2. NEVER use abrasive or flammable solvents to clean
the unit.
3. After cleaning, be sure to completely dry the unit
with a cloth or towel.
4. Store heater in a cool, dry location.
5. It is recommended that you store the unit in its
original carton.
TIP: Over time, dust may accumulate on the grills.
This can be removed by wiping the unit with a damp
cloth.
AUTO SAFETY SHUT-OFF
This heater is equipped with a technologically-advanced
safety system that requires the user to reset the heater if
there is a potential overheat situation. When a potential
overheat temperature is reached, the system will
automatically shut the heater off. It can only resume
operation when the user resets the unit.
If the heater shuts down:
1. Stand the heater upright.
2. Turn Control to OFF
( )
.
3. Unplug the unit and wait 30 minutes.
4. Plug in and operate normally.
Tip Over Shut-Off:
When the heater is accidentally knocked over, it will
instantly shut off. The heater may also shut off if it is
moved or bumped. To reset, simply place the heater in an
upright position, and turn the Mode Control to the desired
heat setting and heater will resume operation.
TROUBLESHOOTING
General Information:
Environmental Factors - There are a number of factors
that will affect your desired comfort level. These factors
can include insulation, open or drafty doors and windows,
and outside temperature. Please check and take action if
any of these potential problems are affecting your
heaters ability to adequately warm your room.
Supplemental Heat - Portable electric heaters are
intended for supplemental heating of rooms to heat the
room you are in and turn down the central heat
thermostat. They are not intended to replace central
heating systems.
Do NOT attempt to repair or adjust any electrical
or mechanical functions on this heater. Doing so
will void warranty. The inside of the heater
contains no user serviceable parts. All servicing
should be performed by qualified personnel only.
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
FEATURES - OPERATIONS
TECHNICAL SPECIFICATIONS
• Amps:12.5
• Wattage:1500W(+5%–10%)
• Workingvoltage:120VAC/60Hz
HOW CONVECTION HEAT WORKS
As the heater warms the air, hot air rises into the room.
This forces the cooler air down towards the heater, where
it is warmed. This cycle continues until the desired
temperature has been reached. There is no fan so
operation is virtually silent.
OPERATING INSTRUCTIONS
1. Carefully unpack your heater from box, please save
the carton for off-season storage.
2. Place heater on a firm, level surface.
3. Plug heater into a standard outlet.
NOTE: Avoid overloading your circuit by not using
other high wattage appliances in the same outlet. At
1500 watts, this unit draws 12.5 Amps.
Mode Control
Turn the Mode Control to the desired setting:
- Off Mode
If you want to shut off the heater at any time during
operation, turn the Mode Control to Off ( ) position.
Lo - LOW Heat
The heater will run continuously at 750W.
Hi - HIGH Heat
The heater will run continuously at 1500W.
NOTE: To start the heater operation, make sure the
Thermostat Control is turned fully clockwise to the highest
position (9). Power Light will remain lit until the heater is
switched off at ( ) position.
Thermostat Control
1. Before setting the thermostat, allow heater to operate
and warm up the room. Set the thermostat to the
highest setting (9) to start the heater.
2. When the desired temperature comfort level is
reached, lower the thermostat setting until the heater
stops operating. This is done by moving the
Thermostat Control toward lower setting.
3. The thermostat will now automatically maintain the
pre-set temperature level by turning the heater ON
and OFF.
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not
let bare skin touch hot surfaces. If provided, use
handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding, papers,
clothes, and curtains at least 3 feet (0.9 m) from the
front of the heater and keep them away from the
sides and rear.
3. Extreme caution is necessary when any heater is
used by or near children or invalids and whenever
the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or
plug or after the heater malfunctions, has been
dropped or damaged in any manner. Discard heater,
or return to authorized service facility for
examinationand/orrepair.
6. Do not use outdoors.
7. This heater is not intended for use in bathrooms,
laundry areas and similar indoor locations. Never
locate heater where it may fall into a bathtub or
other water container.
8. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners, or similar coverings. Do not
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
9. To disconnect heater, turn controls to off, then
remove plug from outlet.
10. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or
exhaust in any manner. Do not use on soft surfaces,
like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside.
Do not use it in areas where gasoline, paint, or
flammable liquids are used or stored.
13. Use this heater only as described in this manual. Any
other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons.
14.Alwaysplugheatersdirectlyintoawalloutlet/
receptacle. Never use with an extension cord or
relocatablepowertap(outlet/powerstrip).
15. When unplugging, be sure to pull by the plug and
not the cord.
16. If the heater will not operate, see specific instructions
on Auto Safety Shut-off.
17. DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
your warranty. The inside of the unit contains no user
serviceable parts. All servicing should be performed
by qualified personnel only.
18. Discontinue use if plug or outlet is hot. It is
recommended that the outlet be replaced if plug or
outlet is hot to touch.
19. The heater must not be located immediately below a
socket-outlet. Do not use this heater in the
immediate surroundings of a bath, a shower or a
swimming pool.
SAVE THESE
INSTRUCTIONS
CLEANING / MAINTENANCE
AUTO SAFETY SHUT-OFF
LEA Y GUARDE ESTAS
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
Para reducir el riesgo de incendios, descargas eléctricas y
lesiones personales al utilizar electrodomésticos, siga siempre
las precauciones básicas de seguridad, incluyendo las que se
mencionan a continuación:
1.
Lea todas las instrucciones antes de usar este calefactor.
2. El calefactor se calienta al usarlo. Para evitar
quemaduras, NO toque las superficies calientes con la
piel. Si existen, utilice las manijas para mover la
unidad. Mantenga los materiales combustibles, como
muebles, almohadones, sábanas, papeles, ropa y
cortinas a por lo menos 3 pies (0,9m) de la parte
delantera del calefactor y manténgalos alejados de los
costados y de la parte de atrás.
3. Debe tener mucho cuidado cuando el calefactor es
utilizado por, o cerca de niños o inválidos, y siempre
que se deje el calefactor prendido y desatendido.
4. Siempre desenchufe el calefactor cuando no lo utilice.
5. NO utilice el calefactor si el cable o el enchufe están
dañados o luego de una falla, se haya caído o haya
sufrido cualquier tipo de daño. Deseche el calefactor o
devuélvalo al centro de servicio autorizado para su
revisióny/oreparación.
6. NO utilizar en el exterior.
7. Este calefactor no está diseñado para ser utilizado en
baños, lavaderos y zonas similares de interiores.
NUNCA coloque el calefactor donde pueda caerse
dentro de una bañera u otro recipiente con agua.
8. No coloque el cable debajo de la alfombra. No cubra el
cable con alfombras, tapetes o artículos similares. No
pase el cable por debajo de muebles o
electrodomésticos. Coloque el cable lejos del área de
tráfico y donde no se tropiece con él.
9. Para desconectarlo, gire el control a la posición OFF,
luego quite el enchufe del tomacorriente.
10. No inserte ni permita que objetos extraños penetren
en la ventilación o salida de aire ya que esto puede
causar un choque eléctrico o incendio, o dañar el
calefactor.
11. Para evitar un posible incendio, no bloquee las
entradas de aire o escape de ninguna manera. No lo
use en superficies blandas, como una cama, donde las
aberturas se pueden bloquear.
12. Un calefactor tiene partes calientes y que pueden
producir chispas en su interior. NO lo utilice en áreas
donde se utiliza o se guarda gasolina, pintura o
líquidos inflamables.
13. Utilice este calefactor sólo como se describe en este
manual. Cualquier otro uso no recomendado por el
fabricante puede provocar incendios, descargas
eléctricas o lesiones a personas.
14. Siempre conecte el calefactor directamente a un
tomacorriente de pared. Nunca lo use con un cable de
extensión o con un tomacorriente múltiple.
15. Al desenchufarlo, asegúrese de tirar del enchufe y no
del cable.
16. Si el calefactor no funciona, vea las instrucciones
específicas del apagado automático de seguridad.
17. NO intente reparar o ajustar ninguna función eléctrica
o mecánica de esta unidad. El hacerlo invalidará la
garantía. La unidad no contiene partes reparables por
el usuario. Toda reparación debe ser realizada
únicamente por personal calificado.
18. Deje de usarlo si el cable o el enchufe se calienta. Se
recomienda que reemplace el tomacorriente si el
enchufe o el tomacorriente se calienta.
19. El calefactor no se debe localizar inmediatamente
debajo de un tomacorriente. No use este calefactor en
áreas cercanas a un baño, una ducha o una piscina.
CONSERVE ESTAS
INSTRUCCIONES
CARACTERISTICAS Y FUNCIONAMIENTO
ESPECIFICACIONES TECNICAS
• Amperes:12.5
• Potencia:1500W(+5%–10%)
• Voltajedefuncionamiento:120vCA/60Hz
FUNCIONAMIENTO DE LA CONVECCIÓN
DE CALOR
A medida que el calefactor calienta el aire, el aire
caliente sube en la habitación. Esto obliga que el aire más
frío baje hacia el calefactor, donde es calentado. Este ciclo
continúa hasta que se alcance la temperatura deseada.
No hay ventiladores por tanto la función es silenciosa.
INSTRUCCIONES DE USO
1. Saque cuidadosamente el calefactor de la caja.
Conserve la caja para guardar la estufa fuera de
temporada.
2. Coloque el calefactor en una superficie firma y
nivelada.
3.
Conecte el calefactor en un tomacorriente estándar.
NOTA: Evite sobrecargar el circuito eléctrico evitando
utilizar otro aparato de alta potencia en el mismo
tomacorriente. A 1500 Vatios, esta unidad consume
12.5 Amperes.
Control de modo
Con el Control de modo, seleccione la configuración deseada:
- Modo Apagado
Desea apagar el calefactor en cualquier momento durante
su operación, gire el Control de modo hasta la posición
APAGADO ( ).
Lo - Calor Bajo
El calefactor funcionará continuamente a 750W.
Hi - Calor Alto
El calefactor funcionará continuamente a 1500W.
NOTA: Para comenzar a utilizar el calefactor, asegúrese
de que el control de termostato esté totalmente girado al
valor más alto (9). La luz de encendido permanecerá
iluminada hasta que el calefactor sea apagado, a la
posición APAGADO
( )
.
Control de termostato
1. Antes de configurar el termostato, permita que el
calefactor caliente la habitación. Para encender el
calefactor, coloque el termostato en el valor más alto.
2. Una vez alcanzada la temperatura del nivel de
confort, reduzca el calibrado del termostato de la
unidad hasta que se detenga el calefactor. Esto se
hace girando el control de termostato al valor bajo.
3. El termostato se mantendrá ahora dentro del nivel
precalibrado, determinando el arranque y detención
(ON y OFF) del calefactor.
LIMPIEZA Y MANTENIMIENTO
APAGADO AUTOMATICO DE SEGURIDAD
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
ESTE PRODUCTO TIENE UN ENCHUFE POLARIZADO (una hoja es más
ancha que la otra). A fin de disminuir el riesgo de descarga eléctrica,
este enchufe está diseñado para insertarse en un tomacorriente
polarizado en un solo sentido. Si el enchufe no entra completamente en
el tomacorriente, inviértalo. Si aun así no entra, llame a un electricista
calificado para instalar un tomacorriente apropiado.
NO MODIFIQUE EL ENCHUFE NI ANULE ESTA FUNCION DE SEGURIDAD
DE NINGUNA MANERA.
NOTA: Es normal que el calefactor se encienda y apague
intermitentemente mientras mantiene la temperatura
seleccionada. Para evitar que la unidad se encienda y apague,
es necesario girar el control del termostato hasta High
(9).
PRECAUCIÓN: LA REJILLA FRONTAL SE CALIENTA
CUANDO LA UNIDAD ESTÁ EN FUNCIONAMIENTO.
LIMPIEZA / MANTENIMIENTO
Siempre desenchufe el calefactor y deje que se enfríe
antes de limpiarlo.
1. Limpie la unidad con un paño suave, humedecido en
una solución de jabón suave.
2. NUNCA utilice solventes abrasivos o inflamables para
limpiar la unidad.
3. Luego de limpiarla, asegúrese de secar
completamente la unidad con un trapo o toalla.
4. Guarde el calefactor en un lugar fresco y seco.
5. Se recomienda guardar la unidad en su embalaje
original.
*CONSEJO: Con el transcurso del tiempo se
acumulará polvo en las rejillas delanteras que puede
eliminarse con un paño húmedo.
APAGADO AUTOMATICO DE SEGURIDAD
Este calefactor está equipada con un sistema de seguridad
tecnológicamente avanzado y que requiere que el usuario
la reactive si se produce un recalentamiento. Si la unidad
se recalienta, el sistema la apagará automáticamente y
sólo podrá volver a funcionar si el usuario la reactiva
manualmente.
Si el calefactor se apaga:
1. Coloque el calefactor en forma vertical.
2. GIRE el Control a APAGADO
( )
.
3. Desenchufe la unidad y espere 30 minutos.
4. Enchufela y vuélvala a operar normalmente.
Apagado de inclinación:
Cuando el calefactor se encuentre accidentalmente
inclinada, se apagará de manera inmediata y la luz de
encendido eléctrica permanece iluminada. El calefactor
también se apagará si se la mueve o golpea. Para
restablecerlo, coloque el calefactor en posición vertical, y
gire el Control de modo para seleccionar la configuración
deseada, y el calefactor comenzará a funcionar
nuevamente.
DIAGNOSTICO DE PROBLEMAS
Información general:
Factores medioambientales: Hay muchos factores que
afectarán su nivel de confort deseado. Estos factores
pueden incluir el aislamiento, puertas y ventanas abiertas
o con corriente de aire, y la temperatura exterior. Haga
una revisión y realice las acciones necesarias si alguno de
estos problemas potenciales afectan la capacidad del
calefactor para calentar adecuadamente la habitación.
Calor complementario: Los calefactores eléctricos
portátiles están diseñados para brindar calefacción
complementaria a las habitaciones, para calentar la
habitación en la que usted se encuentra y bajar el
termostato de la central de calefacción. No están
diseñados para sustituir los sistemas centrales de
calefacción.
NO trate de reparar ni ajustar ninguna de las
funciones eléctricas o mecánicas de este
calefactor. Si lo hace, la garantía quedará
anulada. El interior del calefactor no tiene piezas
que el usuario pueda reparar. Las reparaciones
sólo deberán ser realizadas por personal
capacitado.
Figure 1
Figura 1
CALOR
AIRE FRÍO
Figure 2
Thermostat
Control
Power Light
Mode Control
Figura 2
Control de
termostato
Indicador de
encendido
Control de
modo
Si tiene preguntas relacionadas con este producto o si
está interesado en conocer otros productos Holmes
®
,
póngase visite nuestro sitio
web www.holmesproducts.com.
If you have any questions regarding your product or
would like to learn more about other Holmes
®
products,
please visit our website at www.holmesproducts.com.
HLH4422M_13ESM1.indd 2 1/17/13 10:36 AM

Transcripción de documentos

TROUBLESHOOTING Troubleshooting for your Heater Probable Cause Trouble • Heater Does Not Turn On. ☛ Tip-over switch engaged. ☛ Manual user reset is activated. ☛ Not plugged in properly. ☛ Electrical outlet does not hold plug in securely. ☛ Thermostat set too low. ☛ Obstruction causing the heater not to operate. ☛ Circuit breaker trips. • Not Enough ☛ Heater is in Low Heat setting. Heat. ☛ Thermostat set to low. 1 YEAR LIMITED WARRANTY Solution ✔ Set heater upright on a level surface. ✔ Follow reset instructions listed in this manual. ✔ Ensure plug is properly inserted. Make sure electrical outlet and circuit breaker are working. ✔ Have outlet replaced by a licensed electrician. ✔ Turn the Thermostat Control to the highest setting. ✔ Unplug the heater and remove all obstructions. Position your heater 36 inches (91cm) away from all objects. ✔ Make sure no other high wattage appliances are operating on the same circuit and reset breaker if needed. ✔ Change setting to High Heat. ✔ Turn Thermostat Control to the highest setting until the heater restarts. • Heater Cycles ON and OFF Frequently. ☛ The thermostat automatically turns the heater on and off to maintain selected comfort level. ✔ To make this occur less frequently adjust the thermostat control to the highest setting. • Fan Speed Doesn't Change. ☛ High Heat and Low Heat settings control the heat output of the heater and not the fan speed. Fan runs at the same speed on all settings. ✔ Run heater in High Heat for maximum heat output. • Unexpected ☛ You may hear a popping or Noise. crackling sound as the heater heats up. This is normal and safe operation. Once the heater heats up, the crackling sound will go away. ✔ If the noise persists, visit our website at www.holmesproducts.com. • Unexpected ☛ There may be an odor or vapor coming from the heater the first Smell. time you use it or after prolonged or seasonal storage. ✔ This is normal and is the result of dust or other debris accumulating on the heating element. Make sure the heater is in a well ventilated area and continue running until the odor or vapor goes away. DIAGNOSTICO DE PROBLEMAS Solución de problemas del calefactor Posible Causa Problema • El calefactor ☛ El interruptor contra inclinaciones está activado. no ☛ El restablecimiento manual de enciende. usuario está activado. ☛ No está conectado correctamente. Solución ✔ Coloque el calefactor en posición vertical sobre una superficie nivelada. ✔ Siga las instrucciones de restablecimiento que aparecen en este manual. ✔ Compruebe que el enchufe esté insertado correctamente. Asegúrese de que el tomacorriente y el interruptor de circuito funcionen. ✔ Contrate a un eléctrico con licencia para reemplazar el tomacorriente. ✔ Gire el control de termostato al valor más alto. ✔ Cambie el valor a Calor alto. ✔ Gire el control de termostato al valor más alto hasta que el calefactor reinicie. • El calefactor ☛ El termostato automáticamente enciende ✔ Para hacer que este cambio ocurra con menos se enciende y apaga el calefactor a fin de mantener frecuencia, gire el control de termostato al valor y apaga con el nivel de confort seleccionado. más alto. frecuencia. • La velocidad ☛ Los valores de Calor alto y Calor ✔ Utilice el valor Calor alto del calefactor para del bajo controlan la salida de calor del obtener la máxima calefacción. ventilador calefactor y no la velocidad del no cambia. ventilador. El ventilador funciona a la misma velocidad en todas las opciones. • Ruido ☛ Es posible que se escuchen inesperado. chasquidos o crujidos cuando el calefactor se calienta. Esto es parte del funcionamiento normal y seguro. Una vez que el calefactor se caliente, los crujidos cesarán. ✔ Si el ruido persiste, póngase visite nuestro sitio web www.holmesproducts.com. ☛ Es posible que el calefactor • Olor ✔ Esto es normal y es el resultado del polvo u otros produzca olores o vapores la inesperado. residuos que se acumulan en el dispositivo de primera vez que lo utilice o después calefacción. Asegúrese de que el calefactor se de haber estado almacenado una encuentre en un área ventilada y que siga temporada. funcionando hasta que el olor o vapor desaparezcan. HLH4422M_13ESM1.indd 1 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of one year from the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or mechanical functions on this product. Doing so will void this warranty. This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this warranty. This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes. What are the limits on JCS’s Liability? JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory warranty or condition. Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise. JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party. Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction. How to Obtain Warranty Service In the U.S.A. If you have any question regarding this warranty or would like to obtain warranty service, visit our website at www.holmesproducts.com. In Canada If you have any question regarding this warranty or would like to obtain warranty service, visit our website at www.holmesproducts.com. In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any other problem or claim in connection with this product, please write our Consumer Service Department. PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE. © 2013 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved. Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431. Printed In China HLH4422M Holmes® Heater Holmes® Calefactor PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS LEA Y CONSERVE ESTAS IMPORTANTES INSTRUCCIONES INFORMACION DE LA GARANTIA GARANTÍA LIMITADA DE 1 AÑO ☛ El tomacorriente no sostiene el enchufe de manera segura. ☛ El termostato está en un valor demasiado bajo. ☛ Hay obstrucciones que hacen que el ✔ Desconecte el calefactor y retire las obstrucciones. calefactor no funcione. Coloque el calefactor a 91 cm de distancia de los demás objetos. ☛ El interruptor de circuito está ✔ Compruebe que no haya otros aparatos de alto desactivado. vataje funcionando en el mismo circuito y, si es necesario, restablezca el interruptor. • No hay ☛ El calefactor está en la posición de suficiente calor bajo. calefacción. ☛ El termostato está en un valor bajo. Owner’s Guide Guía del usuario WA R R A N T Y I N F O R M AT I O N Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions, o en Canadá, Sunbeam Corporation (Canada) Limited operando bajo el nombre de Jarden Consumer Solutions, (en forma conjunta, “JCS”), garantiza que por un período de uno año a partir de la fecha de compra, este producto estará libre de defectos de materiales y mano de obra. JCS, a su elección, reparará o reemplazará este producto o cualquier componente del mismo que presente defectos durante el período de garantía. El reemplazo se realizará por un producto o componente nuevo o reparado. Si el producto ya no estuviera disponible, se lo reemplazará por un producto similar de valor igual o superior. Ésta es su garantía exclusiva. No intente reparar o ajustar ninguna función eléctrica o mecánica de este producto. Al hacerlo elimínará ésta garantía. La garantía es válida para el comprador minorista original a partir de la fecha de compra inicial y la misma no es transferible. Conserve el recibo de compra original. Para solicitar servicio en garantía se requiere presentar un recibo de compra. Los agentes y centros de servicio de JCS o las tiendas minoristas que venden productos de JCS no tienen derecho a alterar, modificar ni cambiar de ningún otro modo los términos y las condiciones de esta garantía. Esta garantía no cubre el desgaste normal de las piezas ni los daños que se produzcan como resultado de uso negligente o mal uso del producto, uso de voltaje incorrecto o corriente inapropiada, uso contrario a las instrucciones operativas, y desarme, reparación o alteración por parte de un tercero ajeno a JCS o a un Centro de Servicio autorizado por JCS. Asimismo, la garantía no cubre actos fortuitos tales como incendios, inundaciones, huracanes y tornados. ¿Cuál es el límite de responsabilidad de JCS? JCS no será responsable de daños incidentales o emergentes causados por el incumplimiento de alguna garantía o condición expresa, implícita o legal. Excepto en la medida en que lo prohíba la ley aplicable, cualquier garantía o condición implícita de comerciabilidad o aptitud para un fin determinado se limita, en cuanto a su duración, al plazo de la garantía antes mencionada. JCS queda exenta de toda otra garantías, condiciones o manifestaciones, expresa, implícita, legal o de cualquier otra naturaleza. JCS no será responsable de ningún tipo de daño que resulte de la compra, uso o mal uso del producto, o por la imposibilidad de usar el producto, incluidos los daños incidentales, especiales, emergentes o similares, o la pérdida de ganancias, ni de ningún incumplimiento contractual, sea de una obligación esencial o de otra naturaleza, ni de ningún reclamo iniciado contra el comprador por un tercero. Algunas provincias, estados o jurisdicciones no permiten la exclusión o limitación de los daños incidentales o emergentes ni las limitaciones a la duración de las garantías implícitas, de modo que es posible que la exclusión o las limitaciones antes mencionadas no se apliquen en su caso. Esta garantía le otorga derechos legales específicos y es posible que usted tenga otros derechos que varían de un estado, provincia o jurisdicción a otro. Cómo solicitar el servicio en garantía En los Estados Unidos Si tiene alguna pregunta sobre esta garantía o desea recibir servicio de garantía, póngase visite nuestro sitio web www.holmesproducts.com. En Canadá Si tiene alguna pregunta sobre esta garantía o desea recibir servicio de garantía, póngase visite nuestro sitio web www.holmesproducts.com. En los Estados Unidos, esta garantía es ofrecida por Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions, Boca Ratón, Florida 33431. En Canadá, esta garantía es ofrecida por Sunbeam Corporation (Canada) Limited operando bajo el nombre de Jarden Consumer Solutions, 20 B Hereford Street, Brampton, Ontario L6Y 0M1. Si usted tiene otro problema o reclamo en conexión con este producto, por favor escriba al Departamento de Servicio al Consumidor. POR FAVOR NO DEVUELVA ESTE PRODUCTO A NINGUNA DE ESTAS DIRECCIONES NI AL LUGAR DE COMPRA. © 2013 Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions. Todos los derechos reservados. Distribuido por Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions, Boca Raton, Florida 33431. 158248 Rev. A HLH4422M_13ESM1 Impreso en China GCDS-HOL28159-JC GO ONLINE NOW to http://www.holmesproducts.com/HOLCLG201 to receive a FREE GIFT OR PROMO CODE*. It’s our “thanks” to you for being a Holmes® brand customer. -You will also get access to special sale items & promotions on a full assortment of Holmes® branded products. HURRY & SIGN UP TODAY! *While supplies last; subject to availability. INGRESE AHORA MISMO al sitio http://www.holmesproducts.com/HOLCLG201 para recibir un OBSEQUIO GRATIS O UN CÓDIGO DE PROMOCIÓN*. Es nuestra manera de decirle “gracias” por ser cliente de la marca Holmes®. -También obtendrá acceso a promociones y artículos de venta especiales de una completa variedad de productos de la marca Holmes®. ¡APRESÚRESE Y REGÍSTRESE HOY MISMO! *Hasta agotar el stock; sujeto a disponibilidad 1/17/13 10:36 AM P L E A S E R E A D A N D S AV E T H E S E I M P O R TA N T S A F E T Y I N S T R U C T I O N S When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using this heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear. 3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended. 4. Always unplug heater when not in use. 5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair. 6. Do not use outdoors. 7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container. 8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over. 9. To disconnect heater, turn controls to off, then remove plug from outlet. 10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. 11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. 12. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored. 13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. 14. Always plug heaters directly into a wall outlet/ receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). 15. When unplugging, be sure to pull by the plug and not the cord. 16. If the heater will not operate, see specific instructions on Auto Safety Shut-off. 17. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only. 18. Discontinue use if plug or outlet is hot. It is recommended that the outlet be replaced if plug or outlet is hot to touch. 19. The heater must not be located immediately below a socket-outlet. Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool. SAVE THESE INSTRUCTIONS THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY. LEA Y GUARDE ESTAS INSTRUCCIONES DE SEGURIDAD IMPORTANTES Para reducir el riesgo de incendios, descargas eléctricas y lesiones personales al utilizar electrodomésticos, siga siempre las precauciones básicas de seguridad, incluyendo las que se mencionan a continuación: 1. Lea todas las instrucciones antes de usar este calefactor. 2. El calefactor se calienta al usarlo. Para evitar quemaduras, NO toque las superficies calientes con la piel. Si existen, utilice las manijas para mover la unidad. Mantenga los materiales combustibles, como muebles, almohadones, sábanas, papeles, ropa y cortinas a por lo menos 3 pies (0,9m) de la parte delantera del calefactor y manténgalos alejados de los costados y de la parte de atrás. 3. Debe tener mucho cuidado cuando el calefactor es utilizado por, o cerca de niños o inválidos, y siempre que se deje el calefactor prendido y desatendido. 4. Siempre desenchufe el calefactor cuando no lo utilice. 5. NO utilice el calefactor si el cable o el enchufe están dañados o luego de una falla, se haya caído o haya sufrido cualquier tipo de daño. Deseche el calefactor o devuélvalo al centro de servicio autorizado para su revisión y/o reparación. 6. NO utilizar en el exterior. 7. Este calefactor no está diseñado para ser utilizado en baños, lavaderos y zonas similares de interiores. NUNCA coloque el calefactor donde pueda caerse dentro de una bañera u otro recipiente con agua. 8. No coloque el cable debajo de la alfombra. No cubra el cable con alfombras, tapetes o artículos similares. No pase el cable por debajo de muebles o electrodomésticos. Coloque el cable lejos del área de tráfico y donde no se tropiece con él. 9. Para desconectarlo, gire el control a la posición OFF, luego quite el enchufe del tomacorriente. 10. No inserte ni permita que objetos extraños penetren en la ventilación o salida de aire ya que esto puede causar un choque eléctrico o incendio, o dañar el calefactor. 11. Para evitar un posible incendio, no bloquee las entradas de aire o escape de ninguna manera. No lo use en superficies blandas, como una cama, donde las aberturas se pueden bloquear. 12. Un calefactor tiene partes calientes y que pueden producir chispas en su interior. NO lo utilice en áreas donde se utiliza o se guarda gasolina, pintura o líquidos inflamables. 13. Utilice este calefactor sólo como se describe en este manual. Cualquier otro uso no recomendado por el fabricante puede provocar incendios, descargas eléctricas o lesiones a personas. 14. Siempre conecte el calefactor directamente a un tomacorriente de pared. Nunca lo use con un cable de extensión o con un tomacorriente múltiple. 15. Al desenchufarlo, asegúrese de tirar del enchufe y no del cable. 16. Si el calefactor no funciona, vea las instrucciones específicas del apagado automático de seguridad. 17. NO intente reparar o ajustar ninguna función eléctrica o mecánica de esta unidad. El hacerlo invalidará la garantía. La unidad no contiene partes reparables por el usuario. Toda reparación debe ser realizada únicamente por personal calificado. 18. Deje de usarlo si el cable o el enchufe se calienta. Se recomienda que reemplace el tomacorriente si el enchufe o el tomacorriente se calienta. 19. El calefactor no se debe localizar inmediatamente debajo de un tomacorriente. No use este calefactor en áreas cercanas a un baño, una ducha o una piscina. CONSERVE ESTAS INSTRUCCIONES ESTE PRODUCTO TIENE UN ENCHUFE POLARIZADO (una hoja es más ancha que la otra). A fin de disminuir el riesgo de descarga eléctrica, este enchufe está diseñado para insertarse en un tomacorriente polarizado en un solo sentido. Si el enchufe no entra completamente en el tomacorriente, inviértalo. Si aun así no entra, llame a un electricista calificado para instalar un tomacorriente apropiado. NO MODIFIQUE EL ENCHUFE NI ANULE ESTA FUNCION DE SEGURIDAD DE NINGUNA MANERA. HLH4422M_13ESM1.indd 2 F E AT U R E S - O P E R AT I O N S TECHNICAL SPECIFICATIONS • Amps: 12.5 • Wattage: 1500W (+5% –10%) • Working voltage: 120V AC/60Hz CLEANING / MAINTENANCE A U T O S A F E T Y S H U T- O F F Figure 2 Thermostat Control HOW CONVECTION HEAT WORKS As the heater warms the air, hot air rises into the room. This forces the cooler air down towards the heater, where it is warmed. This cycle continues until the desired temperature has been reached. There is no fan so operation is virtually silent. Power Light Mode Control Figure 1 OPERATING INSTRUCTIONS 1. Carefully unpack your heater from box, please save the carton for off-season storage. 2. Place heater on a firm, level surface. 3. Plug heater into a standard outlet. NOTE: Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 watts, this unit draws 12.5 Amps. Mode Control Turn the Mode Control to the desired setting: - Off Mode If you want to shut off the heater at any time during operation, turn the Mode Control to Off ( ) position. Lo - LOW Heat The heater will run continuously at 750W. Hi - HIGH Heat The heater will run continuously at 1500W. NOTE: To start the heater operation, make sure the Thermostat Control is turned fully clockwise to the highest position (9). Power Light will remain lit until the heater is switched off at ( ) position. Thermostat Control 1. Before setting the thermostat, allow heater to operate and warm up the room. Set the thermostat to the highest setting (9) to start the heater. 2. When the desired temperature comfort level is reached, lower the thermostat setting until the heater stops operating. This is done by moving the Thermostat Control toward lower setting. 3. The thermostat will now automatically maintain the pre-set temperature level by turning the heater ON and OFF. CARACTERISTICAS Y FUNCIONAMIENTO ESPECIFICACIONES TECNICAS • Amperes: 12.5 • Potencia: 1500W (+5% –10%) • Voltaje de funcionamiento: 120v CA/60Hz FUNCIONAMIENTO DE LA CONVECCIÓN DE CALOR A medida que el calefactor calienta el aire, el aire caliente sube en la habitación. Esto obliga que el aire más frío baje hacia el calefactor, donde es calentado. Este ciclo continúa hasta que se alcance la temperatura deseada. No hay ventiladores por tanto la función es silenciosa. Figura 1 Figura 2 Control de termostato Indicador de encendido Control de modo CALOR Control de modo Con el Control de modo, seleccione la configuración deseada: - Modo Apagado Desea apagar el calefactor en cualquier momento durante su operación, gire el Control de modo hasta la posición APAGADO ( ). Lo - Calor Bajo El calefactor funcionará continuamente a 750W. Hi - Calor Alto El calefactor funcionará continuamente a 1500W. AIRE FRÍO NOTA: Para comenzar a utilizar el calefactor, asegúrese de que el control de termostato esté totalmente girado al valor más alto (9). La luz de encendido permanecerá iluminada hasta que el calefactor sea apagado, a la INSTRUCCIONES DE USO posición APAGADO ( ). 1. Saque cuidadosamente el calefactor de la caja. Control de termostato Conserve la caja para guardar la estufa fuera de 1. Antes de configurar el termostato, permita que el temporada. calefactor caliente la habitación. Para encender el 2. Coloque el calefactor en una superficie firma y calefactor, coloque el termostato en el valor más alto. nivelada. 2. Una vez alcanzada la temperatura del nivel de 3. Conecte el calefactor en un tomacorriente estándar. confort, reduzca el calibrado del termostato de la NOTA: Evite sobrecargar el circuito eléctrico evitando unidad hasta que se detenga el calefactor. Esto se utilizar otro aparato de alta potencia en el mismo hace girando el control de termostato al valor bajo. tomacorriente. A 1500 Vatios, esta unidad consume 3. El termostato se mantendrá ahora dentro del nivel 12.5 Amperes. precalibrado, determinando el arranque y detención (ON y OFF) del calefactor. NOTE: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, turn the thermostat control to the highest setting (9). CAUTION: FRONT GRILL IS HOT WHEN UNIT IS IN OPERATION. Tip Over Shut-Off: CLEANING/MAINTENANCE TROUBLESHOOTING Always unplug the heater before cleaning and allow the heater to cool down. 1. Clean the unit with a soft cloth moistened with a mild soap solution. 2. NEVER use abrasive or flammable solvents to clean the unit. 3. After cleaning, be sure to completely dry the unit with a cloth or towel. 4. Store heater in a cool, dry location. 5. It is recommended that you store the unit in its original carton. TIP: Over time, dust may accumulate on the grills. This can be removed by wiping the unit with a damp cloth. General Information: AUTO SAFETY SHUT-OFF This heater is equipped with a technologically-advanced safety system that requires the user to reset the heater if there is a potential overheat situation. When a potential overheat temperature is reached, the system will automatically shut the heater off. It can only resume operation when the user resets the unit. If the heater shuts down: 1. 2. 3. 4. When the heater is accidentally knocked over, it will instantly shut off. The heater may also shut off if it is moved or bumped. To reset, simply place the heater in an upright position, and turn the Mode Control to the desired heat setting and heater will resume operation. Environmental Factors - There are a number of factors that will affect your desired comfort level. These factors can include insulation, open or drafty doors and windows, and outside temperature. Please check and take action if any of these potential problems are affecting your heaters ability to adequately warm your room. Supplemental Heat - Portable electric heaters are intended for supplemental heating of rooms to heat the room you are in and turn down the central heat thermostat. They are not intended to replace central heating systems. Do NOT attempt to repair or adjust any electrical or mechanical functions on this heater. Doing so will void warranty. The inside of the heater contains no user serviceable parts. All servicing should be performed by qualified personnel only. If you have any questions regarding your product or would like to learn more about other Holmes® products, please visit our website at www.holmesproducts.com. Stand the heater upright. Turn Control to OFF ( ). Unplug the unit and wait 30 minutes. Plug in and operate normally. LIMPIE ZA Y MANTENIMIENTO APAGADO AUTOM ATICO D E S EG U R ID A D NOTA: Es normal que el calefactor se encienda y apague intermitentemente mientras mantiene la temperatura seleccionada. Para evitar que la unidad se encienda y apague, es necesario girar el control del termostato hasta High (9). PRECAUCIÓN: LA REJILLA FRONTAL SE CALIENTA CUANDO LA UNIDAD ESTÁ EN FUNCIONAMIENTO. LIMPIEZA / MANTENIMIENTO Siempre desenchufe el calefactor y deje que se enfríe antes de limpiarlo. 1. Limpie la unidad con un paño suave, humedecido en una solución de jabón suave. 2. NUNCA utilice solventes abrasivos o inflamables para limpiar la unidad. 3. Luego de limpiarla, asegúrese de secar completamente la unidad con un trapo o toalla. 4. Guarde el calefactor en un lugar fresco y seco. 5. Se recomienda guardar la unidad en su embalaje original. *CONSEJO: Con el transcurso del tiempo se acumulará polvo en las rejillas delanteras que puede eliminarse con un paño húmedo. Apagado de inclinación: Cuando el calefactor se encuentre accidentalmente inclinada, se apagará de manera inmediata y la luz de encendido eléctrica permanece iluminada. El calefactor también se apagará si se la mueve o golpea. Para restablecerlo, coloque el calefactor en posición vertical, y gire el Control de modo para seleccionar la configuración deseada, y el calefactor comenzará a funcionar nuevamente. DIAGNOSTICO DE PROBLEMAS Información general: Factores medioambientales: Hay muchos factores que afectarán su nivel de confort deseado. Estos factores pueden incluir el aislamiento, puertas y ventanas abiertas o con corriente de aire, y la temperatura exterior. Haga una revisión y realice las acciones necesarias si alguno de estos problemas potenciales afectan la capacidad del calefactor para calentar adecuadamente la habitación. Calor complementario: Los calefactores eléctricos portátiles están diseñados para brindar calefacción complementaria a las habitaciones, para calentar la habitación en la que usted se encuentra y bajar el de la central de calefacción. No están APAGADO AUTOMATICO DE SEGURIDAD termostato diseñados para sustituir los sistemas centrales de Este calefactor está equipada con un sistema de seguridad calefacción. tecnológicamente avanzado y que requiere que el usuario NO trate de reparar ni ajustar ninguna de las la reactive si se produce un recalentamiento. Si la unidad funciones eléctricas o mecánicas de este se recalienta, el sistema la apagará automáticamente y calefactor. Si lo hace, la garantía quedará sólo podrá volver a funcionar si el usuario la reactiva anulada. El interior del calefactor no tiene piezas manualmente. que el usuario pueda reparar. Las reparaciones sólo deberán ser realizadas por personal Si el calefactor se apaga: capacitado. 1. Coloque el calefactor en forma vertical. 2. GIRE el Control a APAGADO ( ). 3. Desenchufe la unidad y espere 30 minutos. 4. Enchufela y vuélvala a operar normalmente. Si tiene preguntas relacionadas con este producto o si está interesado en conocer otros productos Holmes®, póngase visite nuestro sitio web www.holmesproducts.com. 1/17/13 10:36 AM
  • Page 1 1
  • Page 2 2

Holmes HLH4422M Manual de usuario

Categoría
Calentadores espaciales
Tipo
Manual de usuario
Este manual también es adecuado para

En otros idiomas