Sony XS-GS130 Instrucciones de operación

Categoría
Altavoces
Tipo
Instrucciones de operación

Este manual también es adecuado para

Separate 2-way
Speakers
Installation/Connections
Instalación/Conexiones
Sony Corporation © 2002 Printed in Thailand
XS-GS160
XS-GS130
Dimensions
Dimensiones
Tweeter
Altavoz de agudos
Unit: mm
Unidad: mm
Woofer
Altavoz de graves
XS-GS160
XS-GS130
ø 39
14.7
ø 158
ø 126
ø 90
44.59.3ø 14220
ø 134
17.3
48.5
ø 127
ø 116
ø 80
5.6
3-244-268-12 (3)
ø 4.5
5 × 10
ø 164
ø 151
Specifications
Speaker Separate type, 2-way
XS-GS160: Woofer 16 cm, cone type
XS-GS130: Woofer 13 cm, cone type
Tweeter 2.5 cm, balance dome type
Maximum input power
XS-GS160: 200 W
XS-GS130: 150 W
Rated input power
XS-GS160: 50 W
XS-GS130: 40 W
Impedance 4 ohms
Sensitivity XS-GS160: 91 dB/W/m
XS-GS130: 90 dB/W/m
Frequency response
XS-GS160: 30 – 26,000 Hz
XS-GS130: 40 – 26,000 Hz
Crossover frequency
5,000 Hz, –12 dB/oct
Mass Woofer:
XS-GS160: Approx. 910 g per
speaker
XS-GS130: Approx. 720 g per
speaker
Tweeter: Approx. 30 g per speaker
Design and specifications subject to change
without notice.
Especificaciones
Altavoces Tipo separado, 2 vías
XS-GS160: Altavoz de graves de
16 cm, tipo cónico
XS-GS130: Altavoz de graves de
13 cm, tipo cónico
Altavoz de agudos de 2,5 cm,
balanceado tipo cúpula
Potencia máxima de entrada
XS-GS160: 200 W
XS-GS130: 150 W
Potencia nominal de entrada
XS-GS160: 50 W
XS-GS130: 40 W
Impedancia 4
Sensibilidad XS-GS160: 91 dB/W/m
XS-GS130: 90 dB/W/m
Respuesta en frecuencia
XS-GS160: 30 – 26 000 Hz
XS-GS130: 40 – 26 000 Hz
Frecuencia de transición
5 000 Hz, – 12 dB/oct
Peso Altavoz de graves:
XS-GS160: Aprox. 910 g por
altavoz
XS-GS130: Aprox. 720 g por
altavoz
Altavoz de agudos: Aprox. 30 g
por altavoz
Diseño y especificaciones sujetos a cambio sin
previo aviso.
Connections
Conexiones
Tweeter (Left)
Altavoz de agudos (Izquierdo)
Tweeter (Right)
Altavoz de agudos (Derecho)
Woofer (Right)
Altavoz de graves (Derecho)
Power amplifier (not supplied)
Amplificador de potencia (no suministrado)
Red-striped cord
Cable con rayas
rojos
2 m × 2
Red-striped cord
Cable con rayas
rojos
Parts list
Lista de componentes
1
2 m × 2
2
Woofer (Left)
Altavoz de graves (Izquierdo)
* White cord — Left speaker
Grey cord — Right speaker
* Cable blanco — Altavoz izquierdo
Cable gris — Altavoz derecho
*
1
*
1
*
2
2
11.5
38.5
31.2
12.9
Instalación
Antes del montaje
Debe existir una profundidad de 44,5 mm (XS-
GS130: 48,5 mm) como mínimo para instalar el
altavoz de agudos. Mida la profundidad del lugar
donde desea montar el altavoz y compruebe que el
altavoz no obstruya ningún componente del
automóvil. Antes de elegir el lugar de montaje, se
debe tener en cuenta lo siguiente.
Asegúrese de que no haya ningún obstáculo en
el lugar de montaje de la puerta (frontal o
posterior) donde desea montar el altavoz.
Es posible que ya exista un orificio de montaje
en el panel interior de la puerta (frontal o
posterior). En este caso, sólo debe modificar el
salpicadero.
Si desea montar este sistema de altavoces en la
puerta (frontal o posterior), asegúrese de que los
terminales del altavoz, el marco o el imán no
interfieren con los componentes interiores como,
por ejemplo, el mecanismo de la ventanilla en la
puerta (al abrir o cerrar la ventanilla), etc.
Asegúrese también de que la rejilla del altavoz
no esté en contacto con accesorios interiores
como, por ejemplo, los picaportes de las
ventanillas y puertas, los reposabrazos, los
compartimentos para guardar objetos situados
en las puertas, las luces o los asientos, etc.
El lugar apropiado para la instalación de los
altavoces de agudos varía según el tipo de
automóvil. Escoja el lugar que mejor se adecue a
su automóvil.
Precauciones
Procure no utilizar el sistema de altavoces
de forma continua con una potencia que
sobrepase la potencia admisible.
Mantenga alejados del sistema de altavoces
objetos como cintas grabadas, relojes o
tarjetas de crédito con codificación
magnética para evitar daños causados por
los imanes de los altavoces.
Si no puede encontrar un emplazamiento
apropiado para montar los altavoces, consulte
al distribuidor de su automóvil o al proveedor
de Sony más próximo.
Installation
Before Mounting
A depth of at least 44.5 mm (XS-GS130: 48.5 mm) is
required to mount the woofer. Measure the depth
of the area where you are to mount the speaker,
and ensure that the speaker is not obstructing any
other components of the car. Keep the following in
mind when choosing a mounting location:
Make sure that nothing is obstructing around
the mounting location of the door (front or rear)
where you are to mount the speaker.
•A hole for mounting may already be cut out of
the inner panel of the door (front or rear). In this
case, you need to modify the board only.
If you are to mount this speaker system in the
door (front or rear), make sure that the speaker
terminals, frame or magnet do not interfere with
any inner parts, such as the window mechanism
in the door (when you open or close the
window), etc.
Also make sure that the speaker grille does not
touch any inner fittings, such as the window
cranks, door handles, arm rests, door pockets,
lamps or seats etc.
The suitable mounting location for the tweeters
varies depending on the type of car. Choose a
location that suits your car.
Precautions
•Do not continuously use the speaker
system beyond the maximum power
handling capacity.
Keep recorded tapes, watches, and
personal credit cards using magnetic
coding away from the speaker system to
protect them from damage caused by the
magnets in the speakers.
If you cannot find an appropriate mounting
location, consult your car dealer or your nearest
Sony dealer before mounting.
Tweeter
Altavoz de agudos
Example
Ejemplo
1
Decide the position to mount the unit.
Determine la posición de montaje de la
unidad.
2
Woofer
Altavoz de graves
(XS-GS160: 16 cm, XS-GS130: 13 cm)
How to remove the woofer grille net
Cómo extraer la red de la rejilla del altavoz de graves
Mount the grill net 0 on 9.
Monte la red de rejilla 0 en 9.
0 9
3
0
0
0
1
Mark the four bolt holes. Make them 3.3 mm* in diameter.
Marque los orificios para los cuatro pernos. Taládrelos con 3,3 mm* de diámetro.
*
* = 5 mm
2
qa
qa
9
qs
Parts list
Lista de componentes
89
×2
0
×2
qa
×8
qs
ø4 × 35
×8
Door
Puerta
Unit: mm
Unidad: mm
XS-GS160: ø 127 mm
XS-GS130: ø 117 mm
ø 3.3 mm
Parts list
Lista de componentes
34
×2
6
×2
7
3K3 × 10
×2
5
×2
required if you mount the tweeter directly to
your car without using 6
necesario si monta el altavoz de agudos
directamente en el automóvil sin utilizar 6
6
8
c
3
6
7
4

Transcripción de documentos

3-244-268-12 (3) Connections Conexiones 線路連接 2 2m×2 規格 Speaker 揚聲器 Separate type, 2-way XS-GS160: Woofer 16 cm, cone type XS-GS130: Woofer 13 cm, cone type Tweeter 2.5 cm, balance dome type Maximum input power XS-GS160: 200 W XS-GS130: 150 W Rated input power XS-GS160: 50 W XS-GS130: 40 W Impedance 4 ohms Sensitivity XS-GS160: 91 dB/W/m XS-GS130: 90 dB/W/m Frequency response XS-GS160: 30 – 26,000 Hz XS-GS130: 40 – 26,000 Hz Crossover frequency 5,000 Hz, –12 dB/oct Mass Woofer: XS-GS160: Approx. 910 g per speaker XS-GS130: Approx. 720 g per speaker Tweeter: Approx. 30 g per speaker Parts list Lista de componentes 零件一覽表 1 Specifications 2m×2 Design and specifications subject to change without notice. Power amplifier (not supplied) Amplificador de potencia (no suministrado) 功率放大器 (不附送) 最大輸入功率 額定輸入功率 阻抗 靈敏度 頻率響應 交岔頻率 重量 獨立式,2 聲道: XS-GS160:低音揚聲器 16 cm 錐型 XS-GS130:低音揚聲器 13 cm 錐型 高音揚聲器 2.5 cm B.D.型 XS-GS160:200 W XS-GS130:150 W XS-GS160:50 W XS-GS130:40 W 4 Ω XS-GS160:91 dB/W/m XS-GS130:90 dB/W/m XS-GS160:30 - 26,000 Hz XS-GS130:40 - 26,000 Hz 5,000 Hz, -12 dB/oct 低音揚聲器: XS-GS160:每個揚聲器約 910 g XS-GS130:每個揚聲器約 720 g 高音揚聲器: 每個揚聲器約 30 g Separate 2-way Speakers Installation/Connections Instalación/Conexiones 安裝∕線路連接 設計和規格有所變更時,恕不另行奉告。 Especificaciones Altavoces Red-striped cord Cable con rayas rojos 紅條紋電線 紅條紋電線 1* 2 1* 2 * White cord — Left speaker Grey cord — Right speaker * Cable blanco — Altavoz izquierdo Cable gris — Altavoz derecho * 白色電線-左揚聲器 灰色電線-右揚聲器 Diseño y especificaciones sujetos a cambio sin previo aviso. XS-GS160 XS-GS130 Sony Corporation © 2002 Printed in Thailand Dimensions Dimensiones 尺寸 Tweeter Altavoz de agudos 高音揚聲器 Tweeter (Left) Altavoz de agudos (Izquierdo) Tweeter (Right) Altavoz de agudos (Derecho) 高音揚聲器(左) 高音揚聲器(右) ø 39 31.2 Unit: mm Unidad: mm 單位:mm 38.5 Red-striped cord Cable con rayas rojos Tipo separado, 2 vías XS-GS160: Altavoz de graves de 16 cm, tipo cónico XS-GS130: Altavoz de graves de 13 cm, tipo cónico Altavoz de agudos de 2,5 cm, balanceado tipo cúpula Potencia máxima de entrada XS-GS160: 200 W XS-GS130: 150 W Potencia nominal de entrada XS-GS160: 50 W XS-GS130: 40 W Impedancia 4Ω Sensibilidad XS-GS160: 91 dB/W/m XS-GS130: 90 dB/W/m Respuesta en frecuencia XS-GS160: 30 – 26 000 Hz XS-GS130: 40 – 26 000 Hz Frecuencia de transición 5 000 Hz, – 12 dB/oct Peso Altavoz de graves: XS-GS160: Aprox. 910 g por altavoz XS-GS130: Aprox. 720 g por altavoz Altavoz de agudos: Aprox. 30 g por altavoz .9 12 14.7 11.5 Woofer Altavoz de graves 低音揚聲器 20 ø 142 9.3 44.5 17.3 ø 134 5.6 48.5 ø 127 5 × 10 XS-GS130 ø 116 低音揚聲器(右) ø 80 低音揚聲器(左) ø 158 ø 90 ø 164 Woofer (Right) Altavoz de graves (Derecho) ø 151 Woofer (Left) Altavoz de graves (Izquierdo) ø 126 ø 4.5 XS-GS160 Installation 安裝 Before Mounting 安裝以前 A depth of at least 44.5 mm (XS-GS130: 48.5 mm) is required to mount the woofer. Measure the depth of the area where you are to mount the speaker, and ensure that the speaker is not obstructing any other components of the car. Keep the following in mind when choosing a mounting location: • Make sure that nothing is obstructing around the mounting location of the door (front or rear) where you are to mount the speaker. • A hole for mounting may already be cut out of the inner panel of the door (front or rear). In this case, you need to modify the board only. • If you are to mount this speaker system in the door (front or rear), make sure that the speaker terminals, frame or magnet do not interfere with any inner parts, such as the window mechanism in the door (when you open or close the window), etc. Also make sure that the speaker grille does not touch any inner fittings, such as the window cranks, door handles, arm rests, door pockets, lamps or seats etc. • The suitable mounting location for the tweeters varies depending on the type of car. Choose a location that suits your car. Precautions • Do not continuously use the speaker system beyond the maximum power handling capacity. • Keep recorded tapes, watches, and personal credit cards using magnetic coding away from the speaker system to protect them from damage caused by the magnets in the speakers. 安裝低音揚聲器至少需要4 4 . 5 m m (X S - G S 1 3 0 : 4 8 . 5 m m )的深度。測量安裝揚聲器區域的深度,確 保揚聲器不會妨礙汽車上的任何其它部件。選擇安 裝位置時,請注意下列事項: • 確保您要安裝揚聲器的車門上的安裝位置周圍(前 面或後面)沒有任何障礙物。 • 車門的內面板上(前面或後面)可能已經開有安裝 孔。這種情況下,只需修正底板。 • 若您打算將該揚聲器系統安裝在車門上(前面或後 面),確保在打開或關閉車窗時,揚聲器的接頭、 框架或磁體不會干擾車門內的車窗機構等內部部件 的動作。此外,確保揚聲器的格柵不會碰到任何內 部裝置,例如車窗搖柄、車門把手、座位扶手、門 套、燈或座位等。 • 高音揚聲器的合適安裝位置視汽車的類型而定。請 選擇適合您汽車的安裝位置。 Tweeter Altavoz de agudos 高音揚聲器 Woofer Altavoz de graves 低音揚聲器 (XS-GS160: 16 cm, XS-GS130: 13 cm) Parts list Lista de componentes 零件一覽表 3 Parts list Lista de componentes 零件一覽表 4 5 ×2 6 ×2 8 9 required if you mount the tweeter directly to your car without using 6 necesario si monta el altavoz de agudos directamente en el automóvil sin utilizar 6 不使用6直接將高音揚聲器安裝在轎車內時使用 7 ×2 qa 如果您找不到適當的安裝位置,即請洽詢您購入 車輛的商店或附近的 Sony 銷售店,然後才進行 安裝。 3K3 × 10 ×2 ×2 Example Ejemplo 示例 ø4 × 35 ×8 ×8 1 ×2 qs 使用前須注意 • 請勿超過最大功率操作容量連續使用揚聲器。 • 將錄製的磁帶、手錶、和使用磁碼的個人信用卡遠 離揚聲器系統放置,以免被揚聲器中的磁鐵損壞。 0 Mark the four bolt holes. Make them 3.3 mm* in diameter. Marque los orificios para los cuatro pernos. Taládrelos con 3,3 mm* de diámetro. 劃出四個螺栓孔,將它們鑽成直徑為 3.3 mm* 的孔。 * = 5 mm XS-GS160: ø 127 mm XS-GS130: ø 117 mm 8 ø 3.3 mm If you cannot find an appropriate mounting location, consult your car dealer or your nearest Sony dealer before mounting. 1 Decide the position to mount the unit. Determine la posición de montaje de la unidad. 選定安裝位置。 Instalación 2 Antes del montaje Debe existir una profundidad de 44,5 mm (XSGS130: 48,5 mm) como mínimo para instalar el altavoz de agudos. Mida la profundidad del lugar donde desea montar el altavoz y compruebe que el altavoz no obstruya ningún componente del automóvil. Antes de elegir el lugar de montaje, se debe tener en cuenta lo siguiente. • Asegúrese de que no haya ningún obstáculo en el lugar de montaje de la puerta (frontal o posterior) donde desea montar el altavoz. • Es posible que ya exista un orificio de montaje en el panel interior de la puerta (frontal o posterior). En este caso, sólo debe modificar el salpicadero. • Si desea montar este sistema de altavoces en la puerta (frontal o posterior), asegúrese de que los terminales del altavoz, el marco o el imán no interfieren con los componentes interiores como, por ejemplo, el mecanismo de la ventanilla en la puerta (al abrir o cerrar la ventanilla), etc. Asegúrese también de que la rejilla del altavoz no esté en contacto con accesorios interiores como, por ejemplo, los picaportes de las ventanillas y puertas, los reposabrazos, los compartimentos para guardar objetos situados en las puertas, las luces o los asientos, etc. • El lugar apropiado para la instalación de los altavoces de agudos varía según el tipo de automóvil. Escoja el lugar que mejor se adecue a su automóvil. Precauciones • Procure no utilizar el sistema de altavoces de forma continua con una potencia que sobrepase la potencia admisible. • Mantenga alejados del sistema de altavoces objetos como cintas grabadas, relojes o tarjetas de crédito con codificación magnética para evitar daños causados por los imanes de los altavoces. Si no puede encontrar un emplazamiento apropiado para montar los altavoces, consulte al distribuidor de su automóvil o al proveedor de Sony más próximo. 3 9 qa qa qs c 2 Unit: mm Unidad: mm 單位:mm Door Puerta 車門 3 Mount the grill net 0 on 9. Monte la red de rejilla 0 en 9. 將格柵網0裝在9上。 6 4 7 0 0 How to remove the woofer grille net Cómo extraer la red de la rejilla del altavoz de graves 如何取下低音揚聲器格柵網 0
1 / 1

Sony XS-GS130 Instrucciones de operación

Categoría
Altavoces
Tipo
Instrucciones de operación
Este manual también es adecuado para

En otros idiomas