Safety information ...............................................................2 Warnings and safety instructions appearing in this guide

Unpacking your appliance ..................................................3 are not meant to cover all possible conditions and situa-

Warranty registration ......................................................3 tions that may occur. Common sense, caution, and care

Installing your appliance ......................................................4 must be exercised when installing, maintaining, or

operat-

Cabinet clearances .........................................................4 ing this appliance.

Leveling the appliance ....................................................4

...................................................................10 Turning your appliance "ON" or "OFF" ..........................11 Adjusting

the temperature .............................................11 Temperature mode ........................................................11

Control lock ................................................................12

Temperature sensor error codes ................................12

Alarms

...........................................................................12

Door ajar ..................................................................12

Power failure .............................................................13

Temperature alarm ....................................................13

Vacation mode ..................................................................13

Obtaining service .............................................................20

Troubleshooting

.................................................................21

Troubleshooting ice-maker ..............................................22

Warranty ...........................................................................23

Use two or more people to move product.

shipped inside the product in a plastic bag along with the

warranty registration card, and other accessory items.

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good

condition. If there is damage, the packaging will be needed

as proof of damage in transit. Afterwards please dispose of

all items responsibly.

This merchandise was carefully packed and thoroughly

Figure 6

tripping which will cause the appliance to shut down. GFCI’s

are generally not used on circuits with power equipment that

must run unattended for long periods of time, unless required to meet local building codes and ordinances.

at any local hardware or plumbing supply store. Bend the

copper tubing to suit your installation being sure not to kink

the tubing. Purchase enough copper tubing length and coil it

behind the unit to form a "service loop" which will allow the

appliance to be pulled out from the installation for servicing or

cleaning. Connect the copper tubing to the "top side" of a

cold water pipe to prevent the ice-maker from plugging with

sediment.

with a 1/4" compression nut fitting. (See Figure 7).

Water pressure must be at a minimum of 20 psi for proper

operation and a maximum of 120 psi.

Make certain all water connections are watertight after installation. Form the tubing so that it will not

vibrate against the cabinet body or kink when your appliance is set in position.

• Do not use any thread sealers on these water line fittings.

• Reverse osmosis, softened water, and de-ionized water are not recommended as they will adversely affect the quality

The water supply to the ice-maker must be turned on prior to

turning the ice-maker on. Failure to do so will cause rapid dry

cycling of the ice-maker mold heater resulting in temperature

control issues in the freezer compartment.

• The unit must be installed level for proper ice-maker

operation.

• The shutoff arm wire must be down in its lowest position for

It is recommended the ice-maker is shut off when removing

the bucket, or ice may be dispensed onto the freezer

compartment floor.

If the ice is not used regularly, it will clump together with

time. For best ice results, discard ice in the bin as required

and allow the ice-maker to make a new fresh batch of ice.

Shut-off the ice-maker by raising the shut-off arm before

removing the bucket.

Figure 8

the "On/Off" keypad. If this alarm occurs, it is

recommended that you check the condition of any

perishables, even if the appliance is operating normally

and the temperature has recovered, as prolonged

power outages could result in excessive temperature

excursions which may spoil perishables.

temperature deviates excessively from your set-point

temperature for an extended period of time, the

RESET" indicator will be displayed below the "ON/

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage

compartment. If the temperature alarm continues to occur,

your unit may require service.

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

This alarm condition can be reset by momentarily pressing

the "On/Off" keypad. If this alarm occurs it is recommended

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and its

controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

concern of directly turning on or off any lights, digital

Vacationmode. Storage compartment temperatures are

Vacation mode.

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will flash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited. A

power outage will not exit Vacation mode, exiting can only

be accomplished manually. To exit Vacation mode and

Pull out until it stops. Lift up on the front of the pan,

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure

3. Remove all contents.

turned-off if the circuit is not required for other items

unit. (See Figure 18).

unit indoors, although this is not required.

warranty.

valve located on the back of the unit, (see page 6).

6. Be sure the exterior water supply line is drained or

blown out to prevent freezing and cracking of the

supply line.

7. We recommend a cap be placed on the water supply

line to prevent dirt and insects from plugging the line.

8. Empty the ice bucket and replace the ice bucket in unit.

operate until ice is dispensed from ice maker to empty

the ice maker mold.

clean thoroughly with warm water and dish soap.

11. Turn unit off to defrost ice storage compartment, see

12. Unplug the unit from the power outlet.

cracks and crevices that may have accumulated dirt

15. Remove the front toe-grille, (see Figure 20), and use a

brush and vacuum to clean dirt and debris from

beneath the unit.

16. Thoroughly clean the toe-grille and re-install on the

unit. (See Figure 20).

17. Remove the solenoid cover and 3 screws. (see Figure

21). Remove the rear access cover, (see Figure 21),

and use a brush and vacuum to clean dirt and debris

from the machine compartment.

• If the plastic defrost drain pan located under the

23. Thoroughly clean the exterior with a cleaner approved

24. Any mounting hardware / fasteners that are showing

25. Once the exterior has been thoroughly cleaned, you

Grille

Access

cover

around perimeter of

access cover.

The water supply to the ice-maker must be turned on prior

to turning the ice-maker on. Failure to do so will cause

temperature control issues in the freezer compartment.

water line

To disconnect the water outlet line: Push up on the

white collar and pull the plastic water line from the bottom

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

beneath door are not obstructed and kept clean to

allow ventilation for the refrigeration system to expel

heat.

4. Plug your appliance into a dedicated power circuit.

6. Maintaining a relatively full storage compartment will

7. Ensure door closing is not obstructed by contents

1. If stored outside, it is recommended that the unit again

extended period of time.

Stainless steel does not stain, corrode, or rust as easily as

ordinary steel, but it is not stain or corrosion proof.

Stainless steels can discolor or corrode if not maintained

properly.

Stainless steels differ from ordinary carbon steels by the

amount of chromium present. It is this chromium that

provides an invisible protective film on the surface called

chrome-oxide. This protective chrome-oxide film on the

contaminants. This is especially important in coastal areas

which can expose the stainless to severe contaminants

such as halide salts, (sodium chloride).

It is strongly recommended to periodically inspect and

thoroughly clean crevices, weld points, under gaskets,

rivets, bolt heads, and any locations where small amounts

of liquid could collect, become stagnant, and concentrate

contaminates. Additionally, any mounting hardware that is

showing signs of corrosion should be replaced.

Frequency of cleaning will depend upon the installation

others.

Typically the most effective and efficient means for routine

cleaning of most stainless steel products is to give the

surfaces a brisk rubbing with a soft cloth soaked in warm

water and a gentle detergent, or mild mixture of ammonia.

Rubbing should, to the extent possible, follow the polish

lines of the steel, and always insure thorough rinsing after

cleaning.

Although some products are called "stainless steel

cleaners," some may contain abrasives which could scratch

finish.

Stainless steel products should never be installed, or stored

in close proximity to chlorine chemicals.

Whichever cleaning product you chose, it should be used in

strict accordance with the instructions of the cleaner

manufacturer.

de blessure grave si vous ne suivez pas les instructions.

sur une surface solide, en protégeant le sol en dessous

• Des sons de l'eau gouttant et coulant causés par le fondant