Modern Forms WS-11310 Palladian Instrucciones de operación

Modern Forms
Marca
Modern Forms
Modelo
WS-11310 Palladian
Tipo
Instrucciones de operación
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
INSTALLATION INSTRUCTION
Palladian
WS-11310
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en
position d’arrêt (« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.
HARDWARE
A1
B1 C1 N1
1
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
INSTALLATION INSTRUCTION
Palladian
WS-11310
PREPARATION
1. Shut o the power at the circuit breaker
and remove existing xture, including
the mounting hardware.
2. Carefully unpack your new xture and
lay out the parts on a clear area. Be careful
not to lose any small parts necessary
for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the screws (C1) from the xture.
4. Hold the crystal (D1), crystal (G1) onto
the xture back plate (L1) using the studs (N1).
5. Place the glass diuser (K1) onto the holder (J1),
secure it using the nuts (I1).
6. Secure the mounting plate (E1) to the junction box (F1)
using the junction box screws (A1). The side of the mounting
plate marked “GND” (E1) must face out.
CONNECTING THE WIRES (Fig. 2)
7. Connect the transformer input wire to supplier wires
as shown in Fig.2, making sure that all wire connectors (B1)
secured. If your outlet box has a green or bare copper
ground wire, connect the xture’s ground wire to it. Otherwise,
connect the xture’s ground wire directly to the mounting plate (E1)
using the green screw provided. After wires are connected, tuck them
carefully inside the junction box.
*Requires Transformer (H1) to be recessed within the junction box
8. Place the xture back plate (L1) over the mounting plate (E1)
and secure with screws (E1).
9. Put the shade (M1) into the clips on the xture back plate (L1) well.
B1 E1H1F1 A1 L1
C1
J1
G1
N1
K1
I1
M1
D1
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
Input
Output
Back Plate Dimensions
Ø
3 1/2"
Ø
2 3/4"
4 3/4"
7"
2
  • Page 1 1
  • Page 2 2

Modern Forms WS-11310 Palladian Instrucciones de operación

Modern Forms
Marca
Modern Forms
Modelo
WS-11310 Palladian
Tipo
Instrucciones de operación
Descargar PDF
informe

En otros idiomas

Documentos relacionados