Bionaire BUL7921CT-UM El manual del propietario

Categoría
Humidificadores
Tipo
El manual del propietario
INFORMACION DE LA GARANTIAPREGUNTAS FRECUENTES
GARANTÍA LIMITADA DE 1 AÑO
Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions, o en Canadá, Sunbeam Corporation
(Canada) Limited operando bajo el nombre de Jarden Consumer Solutions, (en forma conjunta, “JCS”), garantiza que
por un período de uno año a partir de la fecha de compra, este producto estará libre de defectos de materiales y
mano de obra. JCS, a su elección, reparará o reemplazará este producto o cualquier componente del mismo que
presente defectos durante el período de garantía. El reemplazo se realizará por un producto o componente nuevo o
reparado. Si el producto ya no estuviera disponible, se lo reemplazará por un producto similar de valor igual o
superior. Ésta es su garantía exclusiva. No intente reparar o ajustar ninguna función eléctrica o mecánica de este
producto. Al hacerlo elimínará ésta garantía.
La garantía es válida para el comprador minorista original a partir de la fecha de compra inicial y la misma no es
transferible. Conserve el recibo de compra original. Para solicitar servicio en garantía se requiere presentar un recibo
de compra. Los agentes y centros de servicio de JCS o las tiendas minoristas que venden productos de JCS no tienen
derecho a alterar, modificar ni cambiar de ningún otro modo los términos y las condiciones de esta garantía.
Esta garantía no cubre el desgaste normal de las piezas ni los daños que se produzcan como resultado de uso negligente o
mal uso del producto, uso de voltaje incorrecto o corriente inapropiada, uso contrario a las instrucciones operativas, y
desarme, reparación o alteración por parte de un tercero ajeno a JCS o a un Centro de Servicio autorizado por JCS.
Asimismo, la garantía no cubre actos fortuitos tales como incendios, inundaciones, huracanes y tornados.
¿Cuál es el límite de responsabilidad de JCS?
JCS no será responsable de daños incidentales o emergentes causados por el incumplimiento de alguna garantía o
condición expresa, implícita o legal.
Excepto en la medida en que lo prohíba la ley aplicable, cualquier garantía o condición implícita de comerciabilidad o
aptitud para un fin determinado se limita, en cuanto a su duración, al plazo de la garantía antes mencionada.
JCS queda exenta de toda otra garantías, condiciones o manifestaciones, expresa, implícita, legal o de cualquier otra
naturaleza.
JCS no será responsable de ningún tipo de daño que resulte de la compra, uso o mal uso del producto, o por la
imposibilidad de usar el producto, incluidos los daños incidentales, especiales, emergentes o similares, o la pérdida de
ganancias, ni de ningún incumplimiento contractual, sea de una obligación esencial o de otra naturaleza, ni de ningún
reclamo iniciado contra el comprador por un tercero.
Algunas provincias, estados o jurisdicciones no permiten la exclusión o limitación de los daños incidentales o
emergentes ni las limitaciones a la duración de las garantías implícitas, de modo que es posible que la exclusión o las
limitaciones antes mencionadas no se apliquen en su caso.
Esta garantía le otorga derechos legales específicos y es posible que usted tenga otros derechos que varían de un
estado, provincia o jurisdicción a otro.
Cómo solicitar el servicio en garantía
En los Estados Unidos
Si tiene alguna pregunta sobre esta garantía o desea recibir servicio de garantía, llame al 1-800-253-2764 y podrá
obtener la dirección del centro de servicio que le resulte más conveniente.
En Canadá
Si tiene alguna pregunta sobre esta garantía o desea recibir servicio de garantía, llame al 1-800-253-2764 y podrá
obtener la dirección del centro de servicio que le resulte más conveniente.
En los Estados Unidos, esta garantía es ofrecida por Sunbeam Products, Inc. operando bajo el nombre de Jarden
Consumer Solutions, Boca Ratón, Florida 33431. En Canadá, esta garantía es ofrecida por Sunbeam Corporation
(Canada) Limited operando bajo el nombre de Jarden Consumer Solutions, 20 B Hereford Street, Brampton, Ontario
L6Y 0M1. Si usted tiene otro problema o reclamo en conexión con este producto, por favor escriba al Departamento
de Servicio al Consumidor. POR FAVOR NO DEVUELVA ESTE PRODUCTO A NINGUNA DE ESTAS
DIRECCIONES NI AL LUGAR DE COMPRA.
WARRANTY INFORMATION
1 YEAR LIMITED WARRANTY
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada)
Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of one year from
the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair
or replace this product or any component of the product found to be defective during the warranty period.
Replacement will be made with a new or remanufactured product or component. If the product is no longer available,
replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT
attempt to repair or adjust any electrical or mechanical functions on this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable.
Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service
centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and
conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or
misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly,
repair or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not
cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or
statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for
a particular purpose is limited in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use
the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of
contract, fundamental or otherwise, or for any claim brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages
or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from province to province,
state to state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
In the U.S.A.
If you have any question regarding this warranty or would like to obtain warranty service, please call
1-800-253-2764 and a convenient service center address will be provided to you.
In Canada
If you have any question regarding this warranty or would like to obtain warranty service, please call
1-800-253-2764 and a convenient service center address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located
in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing
business as Jarden Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any
other problem or claim in connection with this product, please write our Consumer Service Department. PLEASE DO
NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
INSTRUCCIONES PARA GUARDAR
ACCESORIOS DE REPUESTO
STORAGE INSTRUCTIONS
REPLACEMENT ACCESSORIES
Printed In China
© 2015 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved. Distributed by Sunbeam
Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.
STORAGE INSTRUCTIONS
When not using your humidifier for an extended period
of time:
1. Clean, rinse and thoroughly dry the humidifier as
directed in weekly maintenance. DO NOT leave any
water in the unit when storing. Leaving water in the
unit may render the unit inoperable for the following
season.
2. Place the humidifier in the original carton and store
in a cool, dry place.
REPLACEMENT ACCESSORIES
To order the replacement accessories you can do any of
the following:
• Visityourlocalretailer
• Goto
www.bionaire.com
• CallConsumerServiceat1-800-253-2764
INSTRUCCIONES PARA GUARDAR
Cuando no utilice su humidificador durante un período
prolongado de tiempo:
1. Limpie y seque bien el humidificador según se
detalla anteriormente en la sección: instrucciones de
mantenimiento semanales. NO deje agua dentro de
la unidad cuando guarde el humidificador. Si queda
agua, la unidad podría quedar inutilizable para la
próxima temporada.
2. Coloque el humidificador en su empaque original y
guárdelo en un lugar fresco y seco.
ACCESORIOS DE REPUESTO
Puede ordenar accesorios de repuesto de una de las
siguientes formas:
• Visitesudistribuidorlocal
• Vallaa
www.bionaire.com
• Llameaservicioalconsumidoral1-800-253-2764
DIAGNÓSTICO DE PROBLEMAS
144165 Rev B BUL7921CT_15ESM1 Impreso en China
GCDS-BIO39675-JC
FREQUENTLY ASKED QUESTIONS
TROUBLESHOOTING
TROUBLESHOOTING
Trouble Probable Cause Solution
Water Leaks from
Tank.
Tank/cap gasket is missing.
Unit tilted or not leveled.
Cap not tight enough.
Tank water is Hot.
Remove tank cap and replace or reposition
gasket.
Place unit it on a flat or leveled surface.
Tighten the cap.
Fill with cool water only.
Crack in Tank.
Hot water will cause tank to pressurize.
Tanks will crack if hit or dropped.
Fill with cool water only.
Handle tank with care. If there is crack on
tank, replace with a new tank.
Film on Tank.
Mineral deposits.
Clean/disinfect tank as instructed in weekly
cleaning instructions.
• Mistoutput
minimal to none.
Scale build up on transducer. Remove scale from the transducer.
Reduced or no
mist.
Out of water.
Setting too low.
Transducer plate dirty.
Fill tank.
Increase setting to High.
Clean transducer (refer to Cleaning and
Maintenance Instructions).
Appearance of
minerals or "white
dust".
Tap water contains minerals that
collect inside your humidifier. When
the minerals are released into the air
they often appear as white dust on
your furniture.
Use distilled water in your humidifier. This will
help reduce the precipitation of minerals or
`white dust'.
In addition, use a demineralization cartridge.
ADC14-UM, Arm & Hammer Demineralization
Cartridge available for purchase on
www.bionaire.com.
FREQUENTLY ASKED QUESTIONS
Question Answer
• What are the variables that affect
run time?
The estimated run time for this humidifier is based on average room
conditions. The actual run time of your humidifier is dependent on numerous
variables such as:
Air exchange in the room where the humidifier is placed.
Room construction of the room where the humidifier is placed.
Temperature of the room where the humidifier is placed.
Humidity levels in the room where the humidifier is placed.
Movement of occupants and the opening and closing of doors in the room
where the humidifier is placed.
Home furnishings in the room where the humidifier is placed.
• How do I remove film on water
tank?
See Daily Maintenance instructions. Regular cleaning is recommended.
• How can I extend the run time?
Run your unit on the lowest setting.
If your unit has electronics, set it to your desired humidity level. The unit
will turn on and off, which will extend the run time.
Fill the tank all the way full, place it on the base, let the water empty into
the base until it stops bubbling, then refill the tank full again. This ensures
maximum water capacity and will extend run time.
PREGUNTAS FRECUENTES
PREGUNTAS RESPUESTAS
• Cuáles son las variables que
afectan el tiempo de
funcionamiento?
El tiempo de funcionamiento estimado de este humidificador está basado en las
condiciones ambientales promedio. El tiempo de funcionamiento actual de su
humidificador depende de varios factores tales como:
El intercambio de aire en el cuarto donde se encuentra el humidificador.
La estructura del cuarto donde se encuentra el humidificador.
La temperatura del cuarto donde se encuentra el humidificador.
Los niveles de humedad en el cuarto donde se encuentra el humidificador.
La actividad de los ocupantes y la secuencia en que se abren y cierran las puertas
del cuarto donde se encuentra el humidificador.
El número de muebles presentes en el cuarto donde se encuentra el humidificador.
• Cómo quito la película del
tanque de agua?
Consulte las instrucciones diarias de mantenimiento. Se recomienda una limpieza
regular.
• Cómo puedo extender el
tiempo de funcionamiento?
Haga funcionar la unidad en el modo más bajo.
Si su unidad tiene electrónicos, ajústela al nivel de humedad deseado. La unidad
se encenderá y apagará, extendiendo el tiempo de funcionamiento.
Llene el tanque al máximo, colóquelo en la base, deje que el agua se vacíe en la base
hasta que deje de burbujear, luego llene nuevamente el tanque al máximo. Esto
asegura una capacidad máxima de agua que extenderá el tiempo de funcionamiento.
© 2015 Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions. Todos los derechos reservados.
Distribuido por Sunbeam Products, Inc. operando bajo el nombre de Jarden Consumer Solutions, Boca Raton, Florida 33431.
DIAGNÓSTICO DE PROBLEMAS
Problema Posible Causa Solución
El agua está
goteando del
tanque.
El agua está goteando del tanque.
La unidad está inclianda o no está
nivelada.
La tapa no está suficientemente apretada
.
El agua del tanque está caliente.
Remueva la tapa del tanque y coloque el
aro de goma correctamente
.
Coloque la unidad en una superficie llana o
nivelada.
Cierre la tapa
.
Llene con agua fría solamente
.
El tanque está
agrietado.
El agua caliente causará presión en el tanque.
El tanque se agrietará si es golpeado o
está goteando
.
Llene con agua fría solamente
.
Manipule el tanque con cuidado. Si el tanque
tiene una rajadura, reemplácelo por uno nuevo.
Hay residuos en
el tanque.
Hay depósitos minerales. Limpie/desinfecte el tanque como se indica
en las instrucciones de limpieza semanal.
• Salida de vapor
mínima o nula.
Se depositó sarro en el transductor.
Quite el sarro del transductor
.
• Vaporreducidoo
nulo.
No tiene agua.
Posición muy baja.
La placa del transductor está sucia.
Llene el tanque.
Aumente la posición a Alto.
Limpie el transductor (vea las instrucciones
de limpieza y mantenimiento).
Apariencia de
minerales o
"polvo blanco".
El agua del grifo contiene minerales que
se acumulan en el interior de su
humidificador. Cuando los minerales se
liberan en el aire a menudo aparecen en
forma de polvo blanco en sus muebles.
Utilice agua destilada en el humidificador.
Esto ayudará a reducir la precipitación de
minerales o "polvo blanco".
Además, utilice un cartucho de
desmineralización. ADC14-UM, Arm &
Hammer cartucho de desmineralización.
disponible para su compra en
www.bionaire.com.
If you have any questions regarding your product or would like to learn more about other Bionaire
®
products, please
contact our Consumer Service Department at 1-800-253-2764 or visit our website at www.bionaire.com.
Si tiene preguntas relacionadas con este producto o si está interesado en conocer otros productos Bionaire
®
, póngase en
contacto con nuestro Departamento de Servicio al Cliente: llame al 1-800-253-2764 o visite nuestro sitio web
www.bionaire.com.
Instruction Leaflet
Folleto de Instrucciones
MODEL: BUL7921CT
MODELO: BUL7921CT
Questions? Comments? Call 1-800-253-2764 in North America.
¿Preguntas? ¿Comentarios? Llame al 1-800-253-2764 en Norteamérica.
pure indoor living
vida en interiores puros
Lea las instrucciones antes de usarlo. Consérvelas para futuras consultas.
Read instructions before operating. Retain for future reference.
ULTRASONIC
HUMDIFIER WITH
ADVANCED DIGITAL HUMIDISTAT
ULTRASÓNICO
HUMIDIFICADOR CON
MEDIDOR DE HUMEDAD
DIGITAL AVANZADO
BUL7921CT_15ESM1.indd 1 4/2/15 3:47 PM
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
FEATURES - OPERATIONS
Digital Humidistat Control
Your humidifier is equipped with a digital humidistat that
allows you to set your humidifier to your desired comfort
level by turning the Dial Wheel on the control panel.
To preset a precise comfort level, turn the Dial Wheel to
adjust the humidity level ranging from 30% to 60%
(Default: “ ”). The LCD Display will show the selected
humidity level for 3 seconds and then change back to show
the room humidity. The Set humidity level will illuminate
on top left of the LCD Display. When the room humidity level
rises above the set humidity, the humidifier will stop. When the
room humidity level drops below the set humidity, the humidifier
will turn on automatically to maintain the preset humidity level.
NOTE: To shut the humidifier off at any setting, press the
Power Button ( ). The humidistat has memory. This means
that when you turn the unit back on, it will be at the last
humidity setting before the humidifier was turned off.
However, if the humidifier is unplugged, the digital
humidistat will no longer remember the previous humidity
setting. You will need to reset the digital humidistat if the
humidifier is unplugged.
WARNING: DO NOT move the humidifier with water in
the tank or the humidifier base. The moving action of the
water may activate the water tank’s release nozzle and
overfill the humidifier base. This may cause the
humidifier to function intermittently, or stop emitting
mist. Should this occurs, simply remove the excess water
from the humidifier base.
NOTES:
• High setting will produce the maximum moisture level
and Low setting will produce the longest run time and
quieter performance.
• Whenthehumidifierrunsoutofwater,thetransducer
will automatically shut off.
• The9holesonthebottomrightoftheunitarepartof
the humidistat sensor.
Tank Empty Light
Once the tank is empty, the Tank Empty Light will
illuminate. Turn off your humidifier and unplug it from the
electrical outlet. Before refilling, empty any residual water
from the base and the tank (follow the daily maintenance
instructions). Then follow the Filling Instructions to refill the
tank and put back into the humidifier to begin operation. The
Tank Empty Light will go off.
Timer
Your humidifier is equipped with 24-Hour Auto Shut-off Timer
feature. This allows you to program your humidifier to shut
off automatically after running a defined time interval.
1. Press the Timer Button ( ) once. The "Hr" icon will
begin to blink.
2. Turn the Dial Wheel to adjust from 0 to 24 to select
your desired time interval for the humidifier to shut-off
automatically.
3. The selected hour will appear on the LCD Display for 3
seconds and then the LCD Display will return to show the
Room Humidity. The Timer icon ( ) will appear on
the LCD Display to indicate that the selected timer.
4. When timer is set, you may check the remaining time
while humidifier is still in operation. Press the Timer
Button and the remaining time (e.g., 7 Hr) will
illuminate on the LCD Display for 3 seconds.
5. To cancel the Timer feature, press the Timer Button
( ). The remaining time will appear on the screen.
Turn the Dial Wheel to 0 hours. The Timer will then be
cancelled.
21. Never place housing under water flow or immerse in
liquids.
22. Do not plug in the cord with wet hands: electric shock
could result.
23. Do not pour water in any openings other than the
water tank.
24. To prevent damage to surfaces, do not place humidifier
under overhanging surfaces.
25.NEVERoperateunitwithoutwaterinthetank.
26. Do not move unit after it has been used until unit cools
completely.
27. Use both hands when carrying full tank of water.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
NOTE: This is an electrical appliance and requires
attention when in use.
NOTE: If moisture forms on the walls or windows of the
room, turn off the humidifier. The room already has plenty
of humidity and additional moisture may cause damage.
NOTE: DO NOT block air inlet or outlet.
Cord and Plug Installation Safety Instructions:
The length of cord used on this appliance was selected to
reduce the hazards of becoming tangled in, or tripping
over a longer cord. If a longer cord is necessary an
approved extension cord may be used. The electrical
rating of the extension cord must be equal to or greater
than the rating of the humidifier (refer to the rating
information placed on the humidifier). Care must be
taken to arrange the extension cord so that it will not
drape over the countertop or tabletop where it can be
pulled on by children or accidentally tripped over.
FCC STATEMENT
Potential for Radio/Television interference
This device complies with Part 18 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
This product has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 18 of the FCC rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. The
product generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the
interference will not occur in a particular installation. If
the product does cause harmful interference to radio or
television reception, which can be determined by turning
the product on or off, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheproductandthe
receiver.
• Connecttheproductintoanoutletonacircuit
different from that to which the receiver is connected.
• Consultthedealeroranexperiencedradio/TV
technician for help.
• Changesormodificationsnotexpresslyapprovedby
the party responsible for compliance could void the
user’s authority to operate the equipment.
HOW ULTRASONIC WORKS:
An ultrasonic transducer atomizes water, producing
refreshing visible cool mist.
NOTE: A humidity level below 20% can be unhealthy
and uncomfortable. The recommended humidity level is
between 40%-50%.
NOTE:
To avoid white dust use only distilled water especially if:
A) you suffer from respiratory problems or B) you live in an
area where the water has a high mineral content.
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance
directlyintoa120VACelectricaloutlet.
3. Keep the cord out of heavy traffic areas. To avoid
firehazard,NEVERputthecordunderrugsornear
heat registers.
4. DO NOT place humidifier near heat sources such as
stoves, radiators, and heaters. DO locate your
humidifier on an inside wall near an electrical outlet.
The humidifier should be at least 4 inches (10 cm)
away from the wall for best results.
5. NEVERplacehumidifierinanareawhereitis
accessibletochildren.NEVERusehumidifierina
closed room, particularly where a child may be
sleeping, resting, or playing (a closed room may
result in excessive humidity).
6.
WARNING:
Do not attempt to refill humidifier without
first unplugging the unit from its electrical outlet. Failure
to heed this warning may cause personal injury. Be sure
to unplug the unit by pulling on the plug and not the
cord.
7. Never place anything over moisture outlet when the
unit is running.
8. NEVERdroporinsertanyobjectintoanyopenings.
9. DO NOT operate any appliance with a damaged cord
or plug, after the appliance malfunctions, or if it has
been dropped or damaged in any manner. Return
appliance to manufacturer for examination, electrical
or mechanical adjustment, or repair.
10.
Use appliance only for intended household use as
described in this manual. Any other use not
recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The use of
attachments not recommended or sold by the
manufacturer may cause hazards.
11. DO NOT use outdoors.
12. Always place humidifier on a firm, flat, level surface.
A waterproof mat or pad is recommended for use
underthehumidifier.NEVERplaceitonarugor
carpet, or on a finished floor that may be damaged
by exposure to water or moisture.
13. DO NOT allow the Moisture Outlet to directly face the
wall. Moisture could cause damage, particularly to wall
paper.
14. Humidifier should be unplugged when not in use.
15.
NEVERtilt,move,orattempttoemptyunitwhileitis
operating. Shut off and unplug before removing the
water tank and moving the unit.
16.
This humidifier requires daily and weekly
maintenance to operate appropriately. Refer to daily
and weekly cleaning procedures. Use only cleaners
and additives recommended by the manufacturer.
17.
NEVERusedetergents,gasoline,glasscleaner,
furniture polish, paint thinner, or other household
solvents to clean any part of the humidifier.
18.
Excessive humidity in a room can cause water
condensation on windows and some furniture. If this
happens, turn the humidifier OFF.
19.
Do not use humidifier in an area where humidity
level is in excess of 50%. Use a hygrometer,
available at your local retailer or through the
manufacturer, to measure the humidity.
20.
DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
your warranty. The inside of the unit contains no
user serviceable parts. All servicing should be
performed by qualified personnel only.
FEATURES - OPERATIONS
FEATURES - OPERATIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
PRE-OPERATING INSTRUCTIONS
1. Be sure the humidifier is switched OFF and the unit is
disconnected from the electrical outlet.
2. Select a location for your humidifier, on a flat surface,
about 4 inches (10 cm) away from the wall. DO NOT
place the humidifier on a finished floor or near
furniture, which can be damaged by too much moisture
or water. Place on a moisture resistant surface.
FILLING THE WATER TANK
1. Remove the tank from the main housing.
2. Bring the tank to the sink, turn upside down and
twist off the tank cap by turning counter clockwise.
Fill tank with cool, fresh tap water. DO NOT fill with
warm water as this may cause leaking. Replace the
cap on tank FIRMLY.
3. Place tank back on to the base. The tank will
immediately begin to empty into the base.
4. Plugthehumidifierintoa120Velectricaloutlet.
OPERATING INSTRUCTIONS
Read below instructions carefully before operating:
Power Button
Press the Power Button to turn the humidifier on, the LCD
Display shows the Room humidity level. The humidifier will
run at High setting and the icon will illuminate on LCD
Display. Press the Power button to manually turn off.
Mist Control
Press the Mist Control Button to select your desired setting
(Low-High). Once selected, the Setting Indicators will
illuminate to indicate which setting is activated.
CARACTERISTICA - FUNCIONAMIENTO
CARACTERISTICA - FUNCIONAMIENTO
CARACTERISTICA - FUNCIONAMIENTO
LEA Y CONSERVE ESTAS IMPORTANTES
INSTRUCCIONES DE SEGURIDAD
ESTE PRODUCTO TIENE UN ENCHUFE POLARIZADO (una hoja es más
ancha que la otra). A fin de disminuir el riesgo de descarga eléctrica, este
enchufe está diseñado para insertarse en un tomacorriente polarizado en
un solo sentido. Si el enchufe no entra completamente en el tomacorriente,
inviértalo. Si aun así no entra, llame a un electricista calificado para instalar
un tomacorriente apropiado.
NO MODIFIQUE EL ENCHUFE NI ANULE ESTA FUNCION DE SEGURIDAD
DE NINGUNA MANERA.
Control de vapor
Presione el botón Control de vapor para seleccionar la
configuración deseada (Bajo-Alto). Una vez seleccionada, los
Indicadores de configuración se iluminarán para indicar
la configuración que se ha activado:
Control digital del medidor de humedad
Su humidificador está equipado con un medidor de humedad
digital que le permite configurar su humidificador al nivel de
comodidad deseado al girar la rueda indicadora en el panel de
control. Para predeterminar un nivel de comodidad preciso,
gire la rueda indicadora para ajustar el nivel de humedad que
oscila entre el 30% y el 60% (Predeterminado: “ ”). El
visor LCD mostrará el nivel de humedad seleccionado durante 3
segundos y luego volverá a mostrar la temperatura ambiente.
El botón Configurar el nivel de humedad se encenderá en
la parte superior izquierda del visor LCD. Cuando el nivel de
humedad del ambiente ascienda por encima de la humedad
establecida, el humidificador se detendrá. Cuando la humedad
del ambiente sea menor a la establecida, el humidificador se
encenderá de manera automática para mantener el nivel de
humedad configurado previamente.
NOTA: Para apagar el humidificador en cualquier
configuración, presione el Botón Encendido ( ). El medidor
de humedad tiene memoria. Significa que cuando lo vuelva a
encender, la unidad tendrá la última configuración de
humedad que tenía antes que se apagara el humidificador.
Sin embargo, si el humidificador está desenchufado, el
medidor de humedad digital no recordará la configuración de
humedad previa. Deberá reiniciar el medidor de humedad
digital si el humidificador está desenchufado.
ADVERTENCIA:NOMUEVAelhumidificadorcuando
tenga agua en el tanque o en la base. La acción de
movimiento podría activar la boquilla de descarga del
tanque de agua y saturar la base del humidificador. Si
sucediera, el humidificador funcionaría intermitentemente
y dejaría de emitir vapor. En este caso, simplemente
elimine el exceso de agua de la base del humidificador.
NOTAS:
• Laposición alta producirá el máximo nivel de
humedad y una posición baja ofrecerá el mayor
tiempo de uso y un funcionamiento más silencioso.
• Cuandoelhumidificadorsequedesinagua,el
transductor se apagarán automáticamente.
• Los9orificiosenlaparteinferiorderechadelaunidad
constituyen el sensor del medidor de humedad.
Luz de tanque vacío
Una vez que el tanque esté vacío, se encenderá la luz de
tanque vacío. Apague el humidificador y desconéctelo del
tomacorriente. Antes de cargarlo nuevamente, retire el agua
que quede en el tanque y en la base (siga las instrucciones
de mantenimiento diario). Luego, siga las instrucciones de
llenado para volver a cargar el tanque y colóquelo en el
humidificador para que comience a funcionar. Se apagará la
luz de tanque vacío.
Temporizador
Su humidificador viene con la función de temporizador de
apagado automático a las 24 horas. Permite programar el
humidificador para que se apague de manera automática
luegode un plazo determinado.
1. Presione el Botón Temporizador ( ) una vez. El icono de
hora "Hr" empezará a titilar.
2. Gire la rueda indicadora para ajustar de 0 a 24 para
seleccionar el intervalo de tiempo deseado para que el
humidificador se apague automáticamente.
3. LahoraseleccionadaapareceráenelVisorLCDdurante
3segundosyluegoelVisorLCDvolveráamostrarla
Humedad ambiente. El icono Temporizador ( )
aparecerá en el visor LCD para indicar el temporizador
seleccionado.
4. Cuando el temporizador esté configurado, usted puede
verificar el tiempo restante mientras el humidificador
todavía está en funcionamiento. Presione el Botón
Temporizador y el tiempo restante (por ejemplo, 07
horas) se encenderá en el visor LCD durante 3 segundos.
5. Para cancelar la función del Temporizador, presione el
Botón Temporizador ( ). El tiempo restante
aparecerá en la pantalla. Gire la rueda indicadora hasta
00 horas. Entonces se cancelará el Temporizador.
reparables por el usuario. Toda reparación debe ser
realizada únicamente por personal calificado.
21. Nunca coloque el gabinete debajo de la canilla o lo
sumerja en líquidos.
22. No enchufe el cable con las manos húmedas. Puede
ocasionarle una descarga eléctrica.
23. No coloque agua en ninguna abertura que no sea el
tanque de agua.
24. Para prevenir el daño a las superficies, no coloque el
humidificador debajo de ninguna superficie que
sobresalga por encima del mismo.
25.
NUNCA haga funcionar la unidad sin agua en el tanque.
26. Una vez utilizada la unidad, no la mueva hasta que
se haya enfriado completamente.
27. Use las dos manos cuando cargue el tanque de agua.
LEA Y CONSERVE ESTAS
IMPORTANTES
INSTRUCCIONES DE
SEGURIDAD
INFORMACIÓN DE SEGURIDAD PARA EL
CONSUMIDOR
NOTA: Este es un artefacto eléctrico y requiere ser usado
con cuidado.
NOTA: Si se acumula humedad en las paredes o
ventanas del cuarto, apague el humidificador. El cuarto
ya tiene demasiada humedad y la humedad adicional
puede causar daños.
NOTA: NO bloquee la entrada o salida de aire.
Instrucciones de Seguridad en la Instalación del
Cable y el Enchufe :
La longitud del cable de este artefacto fue seleccionada
para reducir el riesgo de enredarse o tropezarse con un
cable más largo. Si necesita usar un cable más largo,
puede utilizar un cable de extensión aprobado. La
capacidad eléctrica del cable de extensión debe ser igual o
mayor que la capacidad del humidificador (consulte la
información sobre clasificación que se encuentra en el
humidificador). No debe permitir que el cable de extensión
cuelgue de la mesada o mesa de tal forma que pueda ser
jalado por niños o causar que alguien se tropiece.
DECLARACIÓN DE LA COMISIÓN
FEDERAL DE COMUNICACIONES (FCC
POR SUS SIGLAS EN INGLÉS)
Posibilidad de interferencias con Radio/ Televisión
Este equipo cumple con la Parte 15 de las Normas de la
FCC. Su funcionamiento está sujeto a las siguientes dos
condiciones: (1) Este equipo no puede causar
interferencia perjudicial y (2) este equipo debe aceptar
toda interferencia recibida, inclusive interferencia que
pueda causar un funcionamiento no deseado.
Este producto ha sido probado y se determinó que cumple
con los límites para un dispositivo digital Clase B, según
la parte 15 del reglamento de la FCC.
Estos límites están diseñados para brindar protección
razonable contra interferencias nocivas en una instalación
residencial. El producto genera, usa y puede irradiar
energía de radiofrecuencia, y si no se lo instala y se lo usa
según las instrucciones, puede causar interferencias
adversas en las comunicaciones radiales. Sin embargo, no
hay garantía de que la interferencia no ocurra en una
instalación en particular. Si el producto causa interferencias
nocivas en la recepción de radio o televisión, lo cual se
puede determinar apagando y encendiendo el producto, se
recomienda al usuario que intente corregir la interferencia
por medio de una de los siguientes métodos:
• Reorientaroreubicarlaantenareceptora.
• Aumentarlaseparaciónentreelproductoyelreceptor.
•
Conectar el producto a una salida en un circuito
diferente de aquella a la cual está conectado el receptor.
•
Pedir ayuda al distribuidor o a un técnico de radio/
TVidóneo.
•
Todo cambio o modificación que no haya sido
expresamente autorizado por la parte responsable de
exigir el cumplimiento podría anular la autoridad del
usuario para usar el equipo.
CÓMO FUNCIONA ULTRASONIC:
Un transductor ultrasónico atomiza el agua y produce un
refrescante vapor frío y visible.
NOTA: Un nivel de humedad menor al 20% puede ser
Debe tomar precauciones básicas de seguridad siempre que
utilice artefactos eléctricos para reducir el riesgo de incendio,
descarga eléctrica y daños personales, incluyendo lo siguiente:
1. Lea completamente las instrucciones antes de utilizar
el artefacto.
2. Para evitar incendio o descarga eléctrica, enchufe el
artefactodirectamenteenuntomacorrientede120VCA.
3.
Mantenga el cable fuera de las zonas de mucho
tráfico. Para evitar incendios, NUNCA coloque el cable
debajo de alfombrillas o cerca de salidas de calefacción.
4.
NO coloque el humidificador cerca de fuentes de calor
como estufas, radiadores y calefactores. NO coloque el
humidificador contra una pared interna cerca de un
tomacorriente. El humidificador debe estar a por lo
menos 4" de la pared para obtener el mejor resultado.
5.
NUNCA coloque el humidificador en una zona
accesible para los niños. NUNCA use el humidificador
en un cuarto cerrado, especialmente donde pueda
haber un niño durmiendo, descansando, o jugando
(un cuarto cerrado puede resultar en excesiva humedad).
6.
ADVERTENCIA: No intente llenar nuevamente el
humidificador sin antes desenchufarlo del tomacorriente.
El no tener en cuenta esta advertencia puede causar
daños personales. Asegúrese de desenchufar la unidad
tirando del enchufe y no del cable.
7. Nunca coloque algo sobre la salida de humedad
cuando la unidad esté funcionando.
8. NUNCA inserte ningún objeto en una de las ranuras.
9. NO utilice ningún artefacto si el cable o el enchufe
están dañados, luego de una falla, o si se ha caído o
ha sufrido cualquier tipo de daño. Devuelva el
artefacto al fabricante para su inspección, ajuste
eléctrico o mecánico, o reparación.
10.
Utilice el artefacto únicamente para el propósito
hogareño indicado en este manual. Cualquier uso
distinto al recomendado por el fabricante puede
causar incendio, descarga eléctrica, o daños
personales. El uso
de accesorios no recomendados o que
no sean vendidos por el fabricante puede ser peligroso.
11.
NO utilizar en el exterior.
12.
Siempre coloque el humidificador en una superficie
firme, plana y nivelada. Se recomienda el colocar
una alfombrilla o bandeja resistente al agua debajo
del humidificador. NUNCA lo coloque sobre un tapete
o una alfombra, o en un piso que pueda dañarse con
el agua o la humedad.
13.
NO haga que la salida de humedad apunte
directamente a la pared. La humedad puede causar
daños, especialmente al empapelado.
14. Se debe desenchufar el humidificador cuando no se usa.
15.
NUNCA incline, mueva o intente vaciar la unidad
mientras esté funcionando. Apague y desenchufe la
unidad antes de quitar el tanque de agua y moverla.
16.
Este humidificador requiere mantenimiento diario y
semanal para funcionar correctamente. Refiérase a
los procedimientos de limpieza diarios y semanales.
Use únicamente limpiadores y aditivos recomendados
por el fabricante.
17.
NUNCA use detergentes, gasolina, limpiavidrios,
limpiador de muebles, diluyente de pintura u otro
solvente hogareño para limpiar ninguna parte del
humidificador.
18. La humedad excesiva en un cuarto puede causar
condensación de agua en las ventanas y en algunos
muebles. Si sucede esto, apague el humidificador.
19. No use el humidificador en un área donde el nivel de
humedad es mayor al 50%. Use un Higrómetro,
disponible en su tienda local o a través del
fabricante, para medir la humedad.
20. NO intente reparar o ajustar ninguna función
eléctrica o mecánica de esta unidad. El hacerlo
invalidará la garantía. La unidad no contiene partes
nocivo e incómodo. El nivel de humedad recomendado es
entre el 40% y el 50%
.
NOTA:
Para evitar el uso de polvo blanco sólo use agua
destilada especialmente si: A) usted sufre de problemas
respiratorios o B) que vive en una zona donde el agua tiene
un alto contenido de minerales.
INSTRUCCIONES PREVIAS AL USO
1. Asegúrese de que el humidificador esté en OFF
(Apagado) y desenchúfelo del tomacorriente.
2. Elija un lugar para su humidificador, en una
superficie plana, aproximadamente a 4 pulgadas de
distancia de la pared. NO coloque el humidificador
sobre un piso pulido o cerca de algún mueble, ya que
lo puede dañar por el exceso de humedad o agua.
Colóquelo sobre una superficie resistente a la humedad.
COMO LLENAR EL TANQUE DE AGUA
1. Retire el tanque de la caja principal.
2. Acerque el tanque hasta la pileta, délo vuelta y
desenrosque la tapa del tanque girando en sentido
contrario a las agujas del reloj. Llene el tanque con
agua fría del grifo. NO llene con agua caliente ya
queestopuedeproducirunapérdida.Vuelvaa
colocar la tapa del tanque CON FIRMEZA.
3. Coloque el tanque nuevamente sobre la base. El tanque
comenzará a vaciarse inmediatamente en la base.
4. Enchufe el cable de corriente en un tomacorriente de
120 voltios AC.
INSTRUCCIONES DE USO
Lea cuidadosamente las instrucciones antes de utilizar:
Botón Encendido
Presione el Botón Encendido para encender el humidificador,
elVisorLCDmuestraelniveldehumedaddelAmbiente. El
humidificador funcionará en la configuración Alta y el
iconoseencenderáenelVisorLCD.Presioneelbotón
Encendido para apagar el humidificador de manera manual
cualquiera sea la configuración.
CLEANING AND MAINTENANCE
INSTRUCTIONS
Humidifiers provide comfort by adding moisture to dry,
heated indoor air. To benefit most from the humidifier
and avoid product misuse, follow all instructions carefully.
Please note that this is an electrical appliance and
requires attention when in use.
In addition, if you do not follow the recommended care
and maintenance guidelines, micro-organisms may be
able to grow in the water within the water tank. You must
routinely follow the cleaning procedures that follow in
order to ensure proper, efficient operation of your
humidifier. Proper maintenance and cleaning is essential
to the continued performance of your unit and the
avoidance of algae or bacteria build-up.
Daily Maintenance:
1. Be sure the unit is OFF and is disconnected from the
electrical outlet.
2. Remove the tank and housing from the base. To
remove the humidifier housing from the base, rotate
the housing lock knob to unlock and lift up the
housing.
3. Carry the base of the unit to the sink, place in sink,
drain any remaining water and rinse thoroughly to
remove any sediment or dirt.
Wipe clean, and dry
with a clean cloth or paper towel.
4. Drain the water from the tank into the sink and rinse
tank thoroughly. Wipe clean, and dry with a clean
cloth or paper towel.
5. Replace the
housing, then refill tank with cool tap water
as instructed
earlier in the Filling Instructions. Do not
overfill.
6. Follow Operating Instructions to turn on the
humidifier.
Weekly Maintenance:
To Remove Scale:
1. Repeat previous steps in
Daily Maintenance.
2. Clean the base by partially
filling the base with one
8-oz cups of undiluted white
vinegar, or by using
Cleanse
Clean
®
solution
(Model
S1710)
by the manufacturer.
Leave this solution in the
base for 20 minutes, while
cleaning all the interior surfaces with a soft brush
(brush not included). Gently scrub the area around
the transducer with a soft brush. Remove base scale
by wiping the base with a cloth dampened with
undiluted white vinegar.
3. Rinse with clean warm water to remove the cleaning
solution before disinfecting the tank.
To Disinfect Humidifier Base and Tank:
1. Fill humidifier tank 1/2 full with water and 1/2
tablespoon of chlorine bleach.
2. Let the solution stand for 20 minutes, swishing every
few minutes. Wet all surfaces.
3. Carefully empty the tank after 20 minutes, and rinse
with warm water until you cannot detect any bleach
smell. Dry with a clean cloth or paper towel.
4. Refill the water tank with cool water and replace
housing (see Filling Instructions above). Follow
Operating Instructions to turn the humidifier ON.
5. To clean the humidifier base, pour out all excess
water. Rise thoroughly to remove any sediment to
dirt. Wipe clean and dry with a clean cloth or paper
towel. Do not use metal cleaning utensils or abrasive
cleansers.
CLEANING / MAINTENANCE
LIMPIEZA Y MANTENIMIENTO
INSTRUCCIONES DE LIMPIEZA Y
MANTENIMIENTO
Los humidificadores proveen confort agregando humedad
al aire seco de los ambientes interiores calefaccionados.
Para beneficiarse al máximo de los humidificadores y
evitar su mal uso, siga todas las instrucciones
cuidadosamente. Tenga en cuenta que éste es un artefacto
eléctrico que requiere atención cuando esté en uso.
Además, si no se siguen las recomendaciones para el
cuidado y mantenimiento, crecerán microorganismos en
el agua dentro de los tanques. Se deben ejecutar
rutinariamente los procedimientos de limpieza que se
indican a continuación para asegurar el funcionamiento
adecuado y eficiente del humidificador que son esenciales
para el rendimiento óptimo constante de la unidad y para
evitar la formación de algas y bacterias.
Mantenimiento diario :
1. Asegúrese de apagar y desenchufar la unidad del
tomacorriente.
2. Retire el tanque de agua y la cubierta del
humidificador. Para retirar la cubierta del
humidificador de la base, gire el cierre de seguridad
para desbloquear y levante la cubierta del
humidificador.
3. Lleve la base de la unidad al fregadero o a la tina,
coloque la base en el fregadero, drene el agua
remanente, enjeague completamente para remover
cualquier sedimento o suciedad, limpie frotando con
un paño y seque con una toalla de tela o papel.
4. Drene el agua de los tanques en el fregadero y
enjuáguelos completamente. Límpielos frotando con un
paño y séquelos con una toalla de tela o de papel.
5. El caso y vuelva a llenar el tanque con agua corriente
como se indicó anteriormente en las instrucciones
para el llenado. No lo llene de más.
6. Siga las instrucciones de funcionamiento para
encender el humidificador.
Mantenimiento semanal
Para extraer el sarro :
1. Repita los pasos previos de
mantenimiento diario.
2.
Limpie la base llenándola
parcialmente con una taza de
250 ml (8 oz.) de vinagre
blanco sin diluir o con
Cleanse
Clean
®
solución
(Model
S1710)
. Deje reposar esta
solución en la base por 20
min. mientras limpia todas
las superficies interiores con un cepillo blando (el cepillo
no está incluido). Friegue suavemente el área que
rodea el transductor con un cepillo blando Quite el sarro
frotando la base con un trapo humedecido con vinagre
blanco sin diluir.
3. Enjuague con agua tibia limpia para extraer la
solución limpiadora antes de desinfectar el tanque.
Para desinfectar la base y los tanques del
humidificador :
1. Llene cada tanque hasta la mitad con agua y 1/2
cucharadita de blanqueador de cloro.
2. Deje que la solución trabaje por 20 minutos, sacudiendo
los tanques de vez en cuando. Moje todas las superficies.
3. Vacíecuidadosamentelabaseylostanquesdespuésde20
minutos y enjuague hasta que ya no se pueda detectar el olor
a cloro. Seque con una tela limpia o con toalla de papel.
4. Vuelvaallenareltanqueconaguafríayreemplaceen
la carcasa (vea las instrucciones de llenado,
previamente). Siga las Instrucciones de funcionamiento
para ENCENDER el humidificador.
5. Para limpiar la base del humidificador, tire todo el agua
de acceso. Enjuague concienzudamente para eliminar
cualquier sedimento de suciedad. Limpiar y secar con un
paño limpio o papel toalla. No utilice utensilios de
limpieza de metal que sean limpiadores abrasivos.
I. Tank Empty Light
J. Set Humidity Indicator
K. Setting Indicators
L. Dial Wheel
M. Timer Button
N. Timer Indicator
O. Mist Control Button
P. Power Button
J
I
K
L
O
P
M
N
Figure 2
Control Panel (close-up)
G
Figure 1
A. Mist Nozzle
B. Humidifier Housing
C. Housing Lock Knob
D. Humidifier Base
E. Control Panel (see Fig.
2 for close-up)
F. Tank Cap
G. Water Tank
H. Tank Handle
H
A
F
B
C
D
E
Transducer
I. Luz de tanque vacío
J. Indicadores de la
humedad establecida
K. Indicadores de
configuración
L. Rueda indicadora
M. Botón Temporizador
N. Visordehoradelreloj
O. Botón control vapor
P. Botón Encendido
J
I
K
L
O
P
M
N
Figura 2
Panel de control (imagen ampliada)
G
Figura 1
A. Boquilla de vapor
B. Cubierta del
humidificador
C. Cierre de seguridad de
la cubierta
D. Base del humidificador
E. Panel de control (vea
la Fig.2 para ampliar
la imagen)
F. Tapa del tanque
G. Tanque de agua
H. Manija de tanque
H
A
F
B
C
D
E
Transductor
BUL7921CT_15ESM1.indd 2 4/2/15 3:47 PM
  • Page 1 1
  • Page 2 2

Bionaire BUL7921CT-UM El manual del propietario

Categoría
Humidificadores
Tipo
El manual del propietario

En otros idiomas