Yamaha CLP-525 El manual del propietario

Marca: Yamaha

Modelo: CLP-525

Categoría: Sintetizador

Tipo: El manual del propietario

Owner’s Manual

Mode d’emploi

CLP

525

For information on assembling the keyboard stand, refer to the instructions at the end of

this manual.

Pour obtenir des informations sur l'assemblage du support du clavier, reportez-vous aux

instructions à la fin de ce manuel.

EnglishFrançais

CLP-525 Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instruc-

tions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may

void your authority, granted by the FCC, to use the prod-

uct.

2. IMPORTANT: When connecting this product to accesso-

ries and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used.

Follow all installation instructions. Failure to follow instruc-

tions could void your FCC authorization to use this prod-

uct in the USA.

3. NOTE: This product has been tested and found to com-

ply with the requirements listed in FCC Regulations, Part

15 for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance

that your use of this product in a residential environment

will not result in harmful interference with other electronic

devices. This equipment generates/uses radio frequen-

cies and, if not installed and used according to the instruc-

tions found in the users manual, may cause interference

harmful to the operation of other electronic devices. Com-

pliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this prod-

uct is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try

to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to dis-

tribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Corporation

of America, Electronic Service Division, 6600 Orangetho-

rpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products dis-

tributed by Yamaha Corporation of America or its subsid-

iaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY

PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave.,

Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Digital Piano

Model Name : CLP-525

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received

including interference that may cause undesired opera-

tion.

See user manual instructions if interference to radio recep-

tion is suspected.

(FCC DoC)

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så

länge som den ar ansluten till vägguttaget, även om själ-

va apparaten har stängts av.

ADVARSEL: Netspændingen til dette apparat er IKKE

afbrudt, sålænge netledningen sidder i en stikkontakt,

som er tændt — også selvom der er slukket på appara-

tets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin

ei irroita koko laitetta verkosta.

(standby)

IMPORTANT NOTICE

FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this appa-

ratus may not correspond with the coloured makings iden-

tifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to

the terminal which is marked with the letter L or coloured

RED.

Making sure that neither core is connected to the earth ter-

minal of the three pin plug.

(2 wires)

This device complies with Part 15 of the FCC Rules. Oper-

ation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2)

this device must accept any interference received, includ-

ing interference that may cause undesired operation.

(fcc_sengen-C)

For AC Power Adaptor

CAN ICES-3 (B)/NMB-3(B)

• This applies only to products distributed by Yamaha Canada

Music Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha

Canada Musique Ltée.

(can_b_01)

CLP-525 Owner’s Manual

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply

(adapter). DO NOT connect this product to any power supply

or adapter other than one described in the manual, on the

name plate, or specifically recommended by Yamaha.

WARNING:

Do not place this product in a position where

anyone could walk on, trip over, or roll anything over power or

connecting cords of any kind. The use of an extension cord is

not recommended! If you must use an extension cord, the

minimum wire size for a 25' cord (or less) is 18 AWG. NOTE:

The smaller the AWG number, the larger the current handling

capacity. For longer extension cords, consult a local

electrician.

This product should be used only with the components

supplied or; a cart, rack, or stand that is recommended by

Yamaha. If a cart, etc., is used, please observe all safety

markings and instructions that accompany the accessory

product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves the

right to change or modify any of the specifications without

notice or obligation to update existing units.

This product, either alone or in combination with an amplifier

and headphones or speaker/s, may be capable of producing

sound levels that could cause permanent hearing loss. DO

NOT operate for long periods of time at a high volume level or

at a level that is uncomfortable. If you experience any hearing

loss or ringing in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

Some Yamaha products may have benches and/or accessory

mounting fixtures that are either supplied with the product or

as optional accessories. Some of these items are designed to

be dealer assembled or installed. Please make sure that

benches are stable and any optional fixtures (where

applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only.

No other uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating

to how a function or effect works (when the unit is operating as

designed) are not covered by the manufacturer’s warranty,

and are therefore the owners responsibility. Please study this

manual carefully and consult your dealer before requesting

service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe

and environmentally friendly. We sincerely believe that our

products and the production methods used to produce them,

meet these goals. In keeping with both the letter and the spirit

of the law, we want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery

which (if applicable) is soldered in place. The average life

span of this type of battery is approximately five years. When

replacement becomes necessary, contact a qualified service

representative to perform the replacement.

This product may also use “household” type batteries. Some

of these may be rechargeable. Make sure that the battery

being charged is a rechargeable type and that the charger is

intended for the battery being charged.

When installing batteries, never mix old batteries with new ones,

and never mix different types of batteries. Batteries MUST be

installed correctly. Mismatches or incorrect installation may

result in overheating and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep

all batteries away from children. Dispose of used batteries

promptly and as regulated by the laws in your area. Note:

Check with any retailer of household type batteries in your

area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for

some reason its useful life is considered to be at an end,

please observe all local, state, and federal regulations that

relate to the disposal of products that contain lead, batteries,

plastics, etc. If your dealer is unable to assist you, please

contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The

model number, serial number, power requirements, etc., are

located on this plate. You should record the model number,

serial number, and the date of purchase in the spaces

provided below and retain this manual as a permanent record

of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

CLP-525 Owner’s Manual

Table of Contents

PRECAUTIONS .................................... 5

About the Manuals ................................ 8

Included Accessories ............................. 8

Panel Controls and Terminals.............. 9

Basic Operations

Setting Up.............................................10

Key Cover ..................................................................10

Music Rest .................................................................10

Turning the Power On.............................................11

Auto Power Off.........................................................12

Using Headphones ...................................................12

Playing the Piano..................................13

Setting the Volume...................................................13

Intelligent Acoustic Control (IAC)........................13

Using the Pedals........................................................14

Using the Damper Resonance ................................14

Using the Metronome..............................................15

Changing the Touch Sensitivity .............................16

Advanced Operations

Playing Various Musical Instrument

Sounds (Voices)....................................17

Selecting a Voice.......................................................17

Listening to the Demo Songs ..................................18

Adding Variations to the Sound (Reverb) ............19

Transposing the Pitch in Semitones ......................20

Fine-tuning the Pitch ...............................................20

Layering Two Voices (Dual mode) ........................21

Playing Duo...............................................................22

Song Playback and Practice .................23

Listening to 50 Preset Songs....................................23

Practicing a One-Hand Part....................................24

Playing from the top of the bar including a rest or

blank...........................................................................24

Recording Your Performance .............25

Recording Your Performance ................................ 25

Changing the Initial Settings of the Recorded Song

....................................................................................26

Deleting Recorded Data ..........................................26

Backing up Data and Initializing the

Settings................................................. 27

Data Maintained When Power is Turned Off...... 27

Saving the User Song data to a computer.............27

Transferring SMF Files Between a Computer and

this Instrument......................................................... 27

Initializing the Settings............................................ 27

Appendix

Troubleshooting ..................................28

Keyboard Stand Assembly...................29

Specifications .......................................32

Index..................................................... 33

CLP-525 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the

following:

• Do not place the power cord near heat sources such as heaters or radiators. Also,

do not excessively bend or otherwise damage the cord, or place heavy objects on

it.

• Only use the voltage specified as correct for the instrument. The required voltage

is printed on the name plate of the instrument.

• Use the specified adaptor (page 32) only. Using the wrong adaptor can result in

damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the instrument

or attempt to disassemble or modify the internal components in any way. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings. If any liquid such as

water seeps into the instrument, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the instrument inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may fall

over and cause a fire.

• When one of the following problems occur, immediately turn off the power switch

and disconnect the electric plug from the outlet. Then have the device inspected

by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used for

extended periods of time, or during electrical storms.

• Read carefully the attached documentation explaining the assembly process.

Failure to assemble the instrument in the proper sequence might result in

damage to the instrument or even injury.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• When transporting or moving the instrument, always use two or more people.

Attempting to lift the instrument by yourself may damage your back, result in

other injury, or cause damage to the instrument itself.

• Before moving the instrument, remove all connected cables, to prevent damage

to the cables or injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the power

switch and disconnect the plug from the outlet. Even when the power switch is

turned off, electricity is still flowing to the product at the minimum level. When

you are not using the product for a long time, make sure to unplug the power

cord from the wall AC outlet.

• Use only the stand specified for the instrument. When attaching the stand or rack,

use the provided screws only. Failure to do so could cause damage to the internal

components or result in the instrument falling over.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/AC power adaptor

Assembly

Location

DMI-5 1/2

CLP-525 Owner’s Manual

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels and

gradually raise the volume controls while playing the instrument to set the

desired listening level.

• Do not insert a finger or hand in any gaps on the key cover or instrument. Also

take care that the key cover does not pinch your finger.

• Never insert or drop paper, metallic, or other objects into the gaps on the key

cover, panel or keyboard. This could cause physical injury to you or others,

damage to the instrument or other property, or operational failure.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

• Do not place the bench in an unstable position where it might accidentally fall

over.

• Do not play carelessly with or stand on the bench. Using it as a tool or stepladder

or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent the

possibility of accident or injury.

• If the bench screws become loose due to extensive long-term use, tighten them

periodically using the included tool.

• Keep special watch over any small children so that they don’t fall off the rear of

the bench. Since the bench does not have a backrest, unsupervised use may

result in accident or injury.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (power lamp is off), electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

NOTICE

To avoid the possibility of malfunction/damage to the product, damage to data, or damage to other property, follow the notices below.

 Handling

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the

instrument, TV, or radio may generate noise. When you use the instrument along with the application on your iPhone/iPad, we

recommend that you set “Airplane Mode” to “ON” on your iPhone/iPad in order to avoid noise caused by communication.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in

a car during the day) to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation.

(Verified operating temperature range: 5° – 40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.

• In the case of a model with a polished finish, bumping the surface of the instrument with metal, porcelain, or other hard objects can

cause the finish to crack or peel. Use caution.

 Instrument/Bench Maintenance

To keep your Clavinova in optimum condition, we recommend that you periodically follow the maintenance points below.

• When cleaning the instrument or bench, use a soft, dry or slightly damp cloth. Do not use paint thinners, solvents, cleaning fluids, or

chemical-impregnated wiping cloths. Otherwise, it may become discolored or degraded.

• If you are using a model with a polished finish, gently remove dust and dirt with a soft cloth. Do not wipe too hard since small

particles of dirt can scratch the instrument's finish. To keep the surface polished, apply commercially available piano polisher to a

soft cloth and wipe the instrument’s surface with it. Then, polish it with a separate cloth. Before using any piano polisher, make sure

to read the instructions for proper usage.

• During extreme changes in temperature or humidity, condensation may occur and water may collect on the surface of the

instrument. If water is left, the wooden parts may absorb the water and be damaged. Make sure to wipe any water off immediately

with a soft cloth.

• As with an acoustic piano, pedals may become tarnished across the ages. When this occurs, polish the pedal with a compound

designed for piano pedals. Before using the compound, make sure to read the instructions for proper usage.

 Saving data

• Saved data may be lost due to malfunction or incorrect operation. Save important data to an external device such as a computer (see

the online manual, Computer-related Operations (page 8)).

Connections

Handling caution

Using the bench (If included)

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

DMI-5 2/2

CLP-525 Owner’s Manual

Information

 About copyrights

• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited

except for your personal use.

• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which

it has license to use others' copyrights. Such copyrighted materials include, without limitation, all computer software, style files,

MIDI files, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of

personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE

OR USE ILLEGAL COPIES.

 About functions/data bundled with the instrument

• Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the original.

 About this manual

• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on

your instrument.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

 Tunin g

• Unlike an acoustic piano, this instrument does not need to be tuned by an expert (although the pitch can be user-adjusted to match

other instruments). This is because the pitch of digital instruments is always maintained perfectly.

About audio files

This instrument does not feature audio file playback or audio recording. In addition, audio signals created via your keyboard

performance are not transmitted to your computer or iPad/iPhone, even if one of them is connected to the [USB TO HOST]

terminal of the instrument.

CLP-525 Owner’s Manual

Thank you for choosing the Yamaha Clavinova.

In order to make the most of the performance potential and features of the instrument,

please read the manuals thoroughly, and keep them in a handy place for later reference.

About the Manuals

This instrument has the following manuals.

 Included Manuals

Owner’s Manual (this book)

Explains how to use the instrument.

Quick Operation Guide (separate

sheet)

Shows in chart form the functions assigned to the

buttons and the keyboard for quick

understanding.

 Online Manuals (PDF)

Computer-related Operations

Includes instructions on connecting this

instrument to a computer, and operations related

to transferring song data.

MIDI Reference

Contains the MIDI Data Format and MIDI

Implementation chart, as well as descriptions on

MIDI functions such as MIDI channel and Local

Control settings.

MIDI Basics (only in English, French

and German)

Contains basic explanations about MIDI.

To obtain these manuals, access the Yamaha

Downloads website, select your country, enter

“CLP-525” in the Model Name box, then click

[SEARCH].

Included Accessories

•Owner’s Manual (this book)

• Quick Operation Guide (separate sheet)

• “50 Greats for the Piano” (music book)

• Online Member Product Registration

•AC power adaptor

•Power cord

•Bench

*1 You will need the PRODUCT ID on the sheet in order

to fill out the User Registration form.

*2 May not be included depending on your particular

area. Please check with your Yamaha dealer.

Yam ah a Do wn l o ad s

http://download.yamaha.com/

CLP-525 Owner’s Manual

Panel Controls and Terminals

[ ] (Standby/On) switch......................... page 11

For turning the power on or setting to standby.

[MASTER VOLUME] knob ..................... page 13

For adjusting the volume of the entire sound.

[DEMO/SONG] button..................... pages 18, 23

For playing the Demo Songs and the Preset Songs.

[PIANO/VOICE] button............. pages 17, 19, 21

For selecting a single Voice, two Voices for layering or

a Reverb Type.

[METRONOME] button .......................... page 15

For starting or stopping the metronome.

[+R], [–L] buttons ....................... pages 17, 20, 24

• In general, these are for selecting the next or

previous Voice.

• During Song playback, these are for selecting the

next or previous Song, and (while holding down

[PLAY]) turning on/off the right-hand and left-

hand Parts individually.

• During Metronome playback, these are for

increasing or decreasing the Tempo.

[REC] button............................................ page 25

For recording your keyboard performance.

[PLAY] button.......................................... page 25

For playing back the recorded performance.

[FUNCTION] .......................................... page 20

Simultaneously holding these two buttons and

pressing the specified key sets will set the MIDI or

Transpose parameters.

[PHONES] jacks....................................... page 12

For connecting a set of standard stereo headphones.

[USB TO HOST] terminal

For connecting to a computer. For details, refer to the

“Computer-related Operations” on the website

(page 8).

NOTICE

Use an AB type USB cable of less than 3 meters.

USB 3.0 cables cannot be used.

[TO PEDAL] jack ..................................... page 30

For connecting the pedal cord.

DC IN jack................................................ page 11

For connecting the power adaptor.

Pedals ....................................................... page 14

For controlling expression and sustain, just as on an

acoustic piano.

Rear

(Keyboard side)

Rear

(Keyboard side)

Rear

(Keyboard side)

CLP-525 Owner’s Manual

Basic Operations

Setting Up

To open the key cover:

Lift the cover slightly, then push and slide it to the end.

To close the key cover:

Slide the cover toward you and gently lower the cover over

the keys.

CAUTION

• Hold the cover with both hands when opening or closing it. Do not

release it until it is fully opened or closed. Be careful to avoid

catching fingers (yours or others, especially children’s) between the

cover and the main unit.

• Do not place objects, such as a piece of metal or paper, on top of the

key cover. Small objects placed on the key cover may fall inside the

unit when the cover is opened and may be nearly impossible to

remove. This could cause electric shock, short circuit, fire or other

serious damage to the instrument.

To raise the music rest:

1. Pull the music rest up and toward yourself as

far as it will go.

2. Flip down the two metal supports at the left

and right on the rear of the music rest.

3. Lower the music rest so that it rests on the

metal supports.

To lower the music rest:

1. Pull the music rest toward yourself as far as it

will go.

2. Raise the two metal supports (at the rear of

the music rest).

3. Gently lower the music rest backward until it

is all the way down.

CAUTION

Do not try to use the music rest in a half-raised position. When lowering the music rest, do not release your hands from the music

rest until it is all the way down.

Key Cover

Music Rest

CAUTION

Be careful to avoid catching

your fingers when opening

or closing the cover.

Setting Up

CLP-525 Owner’s Manual

1. Connect the plugs of the AC power adaptor in the order

shown in the illustration.

WARNING

• Use the specified adaptor (page 32) only. The use of other adaptors may result in irreparable

damage to both the adaptor and the instrument.

• The AC power adaptor is designed for indoor use only. Do not use in any wet environments.

CAUTION

Remove the AC plug from the AC outlet when the instrument is not to be used for extended

periods of time, or during electrical storms.

NOTE

Follow this procedure in reverse order when disconnecting the power adaptor.

2. Press the [ ] (Standby/On) switch to turn the power on.

Power indicator

If you close the key cover without turning the power to standby, the power

indicator remains lit, indicating that the power is still on.

When you’re ready to turn the power to standby, press the [ ](Standby/On)

switch again for a second. The power indicator turns off.

CAUTION

Even when the [ ] (Standby/On) switch is in the standby status, electricity is still flowing to the

instrument at a minimum level. When not using the instrument for an extended period of time, be

sure to unplug the power cord from the wall AC outlet.

Turning the Power On

1-1

1-2

1-3

Power cord

AC outlet

AC power

adaptor

DC IN jack (page 9)

The shape of the plug and outlet

differ depending on locale.

Power indicator

[ ] (Standby/On) switch

Setting Up

CLP-525 Owner’s Manual

To prevent unnecessary power consumption, this instrument features an Auto

Power Off function that automatically turns the power off if the instrument is

not operated for approximately 30 minutes. If you do not want to use the Auto

Power Off function, disable the function as described below. The setting

(disabled or enabled) is retained even if the power is turned off.

Disabling Auto Power Off

Turn the power of the instrument off. Then, while holding

down the lowest key, press the [ ] (Standby/On) switch to

turn on the power again so that the [REC] indicator flashes

three times, indicating that the Auto Power Off function

has been disabled.

You can also disable the Auto Power Off function without

turning the power off, by simultaneously holding down

[DEMO/SONG] and [PIANO/VOICE] and pressing the

A♯ 5 key.

Re-enabling Auto Power Off

To enable the Auto Power Off function again,

simultaneously hold down [DEMO/SONG] and [PIANO/

VOICE] and press the A5 key.

Since this instrument is equipped with two [PHONES]

jacks, you can connect two sets of standard stereo

headphones. If you are using only one set of headphones,

insert a plug into either jack, which automatically shuts off

the speakers.

CAUTION

Do not use headphones at a high volume for an extended period of

time; doing so may cause hearing loss.

Using the headphone hanger

You can hang the headphones on this instrument. Refer to

“Keyboard Stand Assembly” on page 29 for instructions on

installing the headphone hanger.

NOTICE

Do not hang anything other than the headphones on the hanger.

Doing so may damage this instrument or the hanger.

Auto Power Off

Default setting:

Enable

Lowest key

Highest keyA♯ 5

Highest keyA5

Using Headphones

PHONES

Standard stereo phone plug

Bottom surface

CLP-525 Owner’s Manual

Playing the Piano

When you start playing, use the [MASTER VOLUME] knob to adjust the volume of the entire keyboard

sound.

CAUTION

Do not use this instrument at a high volume level for a long period of time, or your hearing may be damaged.

With this function, the sound quality of this instrument is automatically adjusted

and controlled according to the overall volume. Even when the volume is low,

this lets you hear both low sounds and high sounds clearly.

To turn on IAC:

While holding down [PIANO/VOICE],

press the F♯ 0 key.

To turn off IAC:

While holding down [PIANO/VOICE],

press the F0 key.

To adjust IAC Depth:

While holding down [PIANO/VOICE],

press one of the A-1 – D♯ 0 keys.

The higher the value, the more clearly that low and high sounds are heard at

lower volume levels.

Setting the Volume

Intelligent Acoustic Control (IAC)

Level decreases. Level increases.

Default setting:

F♯ 0Lowest key

F0Lowest key

C0: depth 0

(Standard setting)

Lowest key

A-1: depth -3 D♯0: depth +3

Setting range:

A-1 (-3) – D♯ 0 (+3)

Default setting:

C0 (0)

Playing the Piano

CLP-525 Owner’s Manual

Damper Pedal (Right)

Pressing this pedal will sustain notes longer.

Releasing this pedal immediately stops (damps)

any sustained notes. This pedal also features a

“half-pedal” function that creates partial sustain

effects, depending on how far down you press the

pedal.

Sostenuto Pedal (Center)

Pressing this pedal while holding the notes will

sustain the pressed notes (as if the Damper Pedal

had been pressed), but all subsequently played

notes will not be sustained. This makes it possible

to sustain a chord or single low note, for example,

while the other notes are played “staccato.”

Soft Pedal (Left)

Pressing this pedal will reduce the volume and slightly change the timbre of the

notes. The notes played before this pedal is pressed are not affected. When you

select the Jazz Organ Voice, pressing the left pedal switches between fast/slow

rotation of the rotary speaker (page 17).

The Damper Resonance effect simulates the sustain sound of the damper pedal on a grand piano, as if you

were pressing the damper pedal and playing the keyboard. This effect is applied to the entire sound of the

instrument.

To turn on the Damper Resonance:

While holding [PIANO/VOICE], press the G♯2 key.

To turn off the Damper Resonance:

While holding [PIANO/VOICE], press the G2 key.

Using the Pedals

When you press the damper

pedal here, this note and the

notes you play before you release

the pedal sustain longer.

When you press the sostenuto

pedal here while holding the

note, the note will sustain as

long as you hold the pedal.

NOTE

If the damper pedal doesn’t

work, make sure that the pedal

cord is properly plugged into

the main unit (page 30).

Half-pedal function

This function allows you to vary

the sustain length depending

on how far the pedal is

pressed. The farther down you

press the pedal, the more the

sound sustains. For example, if

you press the damper pedal

and all notes you are playing

sound a bit murky and loud

with too much sustain, you can

release the pedal half way or

higher to decrease the sustain

(murkiness).

NOTE

While the sostenuto pedal is

held, the organ and strings

Voices sound continuously

without decay after the notes

have been released.

Using the Damper Resonance

Default setting:

Lowest key G2

(Off)

G♯2

(On)

Playing the Piano

CLP-525 Owner’s Manual

The metronome feature is convenient for practicing with an accurate tempo.

1. Press [METRONOME] to start the Metronome.

2. Press [METRONOME] to stop the Metronome.

Selecting a Beat

While holding down [METRONOME], press one of the C3 – F3 keys.

Adjusting the Tempo

The Metronome tempo can be set from 5 to 280 beats per minute.

•To increase or decrease the value by 1:

While the metronome is playing, press [+R] to increase or [–L] to decrease.

Alternatively, press and hold down [METRONOME], and press the C♯5 key to

increase or B4 key to decrease.

•To increase or decrease the value by 10:

While holding down [METRONOME], press the D5 key to increase or the A♯ 4 key

to decrease.

•To specify a three-digit value:

While holding down [METRONOME], press the relevant C4 – A4 keys one by one

in order. For example to specify “95,” press the C4 (0), A4 (9) and F4 (5) keys in

order.

Resetting the value to the default (120)

While holding down [METRONOME], press the [+R] and [–L] simultaneously,

or press the C5 (default) key.

Adjusting the Volume

While holding down [METRONOME], press one of the keys between C1 and G2

to set the volume of the metronome. Pressing a higher key results in higher

volume, while pressing a lower key results in lower volume.

Using the Metronome

24 7

1356

14 16 19

15 17 18 2013

024579

8631

C♯ 3

Highest key

D♯ 3

D3 E3 F3

A♯ 4

C♯ 5

F4 A4 C5 D5B4Lowest key C1 G2

Adjusting the

Metronome Volume

Selecting

a Beat

Adjusting

the Tempo

Default setting:

0 (C3)

Key Beat

C3 0

C♯32

D3 3

D♯34

E3 5

F3 6

Setting range:

C1 (1) – G2 (20)

Default setting:

D2 (15)

Playing the Piano

CLP-525 Owner’s Manual

You can specify the Touch Sensitivity (how the sound responds to the way you

play the keys).

While holding down [PIANO/VOICE], press one of the A6 – C7 keys.

Changing the Touch Sensitivity

NOTE

This setting is disabled with

some Voices, such as an

organ sound.

Default setting:

B6 (Medium)

Key

Touch

Sensitivity

Description

A6 Fixed

The volume level does not change at all regardless of whether you

play the keyboard soft or hard.

A♯ 6Soft

The volume level does not change much when you play the

keyboard soft or hard.

B6 Medium This is the standard piano touch response.

C7 Hard

The volume level changes very widely from pianissimo to fortissimo

to facilitate dynamic and dramatic expression. You have to hit the

keys hard to produce a loud sound.

A6 Highest key (C7)

A♯ 6

CLP-525 Owner’s Manual

Advanced Operations

Playing Various Musical Instrument Sounds (Voices)

To select “Grand Piano 1”:

Simply press [PIANO/VOICE].

To select another Voice:

After pressing [PIANO/VOICE], press [+R] or [–L] to select the next or previous

Voi ce.

To select a specific Voice:

While holding down [PIANO/VOICE], press one of the C1 – A1 keys. For details

on which Voice is assigned to each key, see the list below.

Voice List

Selecting a Voice

NOTE

To hear the characteristics of

the Voices, play back the

Demo Songs (page 18).

Key Voice Name Voice description

C1 Grand Piano 1

This sound was sampled from a full concert grand piano. It uses

different samples depending on the strength of your playing and

produces smoother tonal changes. Suitable not only for classical

compositions but also for piano pieces of any style.

C♯1 Grand Piano 2 Warm and soft piano sound. Good for playing ballads.

D1 Grand Piano 3

Spacious and clear piano with bright reverb. Good for popular

music.

D♯1 E.Piano 1

An electronic piano sound created by FM synthesis. Good for

standard popular music.

E1 E.Piano 2

The sound of an electric piano using hammer-struck metallic

“tines.” Soft tone when played lightly, and an aggressive tone

when played hard.

F1 Harpsichord

The definitive instrument for baroque music. Since harpsichord

uses plucked strings, there is no touch response. There is,

however, a characteristic additional sound when the keys are

released.

F♯1 Vibraphone

Vibraphone played with relatively soft mallets. The tone becomes

more metallic the harder you play.

G1 Pipe Organ

This is a typical pipe organ sound (8 feet + 4 feet + 2 feet). Good

for sacred music from the Baroque period.

G♯1 Jazz Organ

The sound of a “tonewheel” type electric organ. Often heard in

jazz and rock music. The rotary speed of the rotary speaker

effect can be switched by using the left pedal.

A1 Strings

Stereo-sampled, large-scale strings ensemble with realistic

reverb. Try combining this Voice with piano in the Dual mode.

C♯ 1D♯1F♯1G♯1

C1 D1 E1 F1 G1 A1Lowest key

Playing Various Musical Instrument Sounds (Voices)

CLP-525 Owner’s Manual

Special individual Demo Songs are provided for all of the instrument Voices.

1. Press [DEMO/SONG] to start playback.

The [PLAY] lamp flashes, and the Demo Song for the current Voice starts.

Starting with the selected song, the playback of the Demo Songs will continue.

After the last demo song, the sequence then returns to the first Demo Song and

repeats until you stop it.

To change the Demo Song during playback:

Press the [+R] or [–L] to change to the next or previous Demo Song.

To change to a specific Demo Song, press and hold down the [DEMO/SONG], then

press one of the C1 – A1 keys.

2. Press [DEMO/SONG] or [PLAY] to stop playback.

The [PLAY] lamp turns off.

Demo Song List

The Demo Songs excluding original Songs are short rearranged excerpts from the original

Listening to the Demo Songs

NOTE

If you want to change the

playback tempo, see page 15.

Key Voice Name Title Composer

C1 Grand Piano 1 Bargarolle op. 60 F. F. Chopin

C♯1 Grand Piano 2

Von fremden Landern und Menchen,

Kinderszenen op. 15-1

R. Schumann

D1 Grand Piano 3 Original Original

D♯1 E.Piano 1 Original Original

E1 E.Piano 2 Original Original

F1 Harpsichord

Concerto a cembalo obbligato, 2 violini, viola e

continuo No. 7, BWV. 1058

J. S. Bach

F♯1 Vibraphone Original Original

G1 Pipe Organ Herr Christ, der ein’ge Gottes-Sohn, BWV. 601 J. S. Bach

G♯1 Jazz Organ Original Original

A1 Strings Original Original

Lowest key C1 F1 A1

Playing Various Musical Instrument Sounds (Voices)

CLP-525 Owner’s Manual

This instrument features several Reverb Types that add extra depth and expression to the sound to create a

realistic acoustic ambience. The appropriate Reverb Type and Depth are called up automatically when you

select each of the Voices and Songs. This is why the Reverb Type need not be selected; however, you can

change it if desired.

To select a Reverb Type:

While holding down [PIANO/VOICE], press one of the C2 – E2 keys.

Reverb Type List

To adjust Reverb Depth:

While holding down [PIANO/VOICE], press one of the C3 – G♯4 keys. The

Depth value increases as you press higher keys.

While holding down [PIANO/VOICE], press the A4 key to set the Reverb Depth

to the most suitable value for the current Voice.

Adding Variations to the Sound (Reverb)

Reverb in Dual Mode

An optimum reverb type for the

combination of Voices is

assigned automatically.

Lowest key

C3: depth 0

G♯4: depth 20

The depth value increases as you

press higher keys.

C♯2D♯2

C2 D2 E2

Selecting a

Reverb Type

Adjusting

Reverb Depth

Highest key

Key Reverb Type Description

C2 Recital Hall

Simulates the clear reverb sound you would hear in a medium-

sized concert hall for piano recitals.

C♯2 Concert Hall

Simulates the gorgeous reverb sound you would hear in a large

concert hall for orchestral performances.

D2 Chamber

Suitable for playing chamber music; simulates the intimate

reverb sound you would hear in a spacious room, such as for

classical music recitals.

D♯2Club

Simulates the vivid reverb sound you would hear in a live music

venue or a jazz club.

E2 Off No effect is applied.

Reverb Depth range:

0 (no effect) – 20 (maximum

depth)

Playing Various Musical Instrument Sounds (Voices)

CLP-525 Owner’s Manual

You can shift the pitch of the entire keyboard up or down in semitones in order to facilitate playing in

difficult key signatures, or to easily match the pitch of the keyboard to the range of a singer or other

instruments. For example, if “+5” is selected, playing key C produces pitch F, letting you play a song of F

major as though it were in C major.

To transpose the pitch down:

While holding down [DEMO/SONG] and [PIANO/VOICE], press a key

between F♯ 2 (-6) and B2 (-1).

To transpose the pitch up:

While holding down [DEMO/SONG] and [PIANO/VOICE], press a key

between C♯ 3 (+1) and F♯ 3 (+6).

To restore the normal pitch:

While holding down [DEMO/SONG] and [PIANO/VOICE], press the C3 key.

You can fine-tune the pitch of the entire instrument in about 0.2 Hz steps. This lets you match the keyboard

pitch finely to that of other instruments or CD music.

To tune up (in about 0.2 Hz steps):

Press and hold down the [DEMO/SONG] and

[PIANO/VOICE] simultaneously, and press [+R].

To tune down (in about 0.2 Hz steps):

Press and hold down the [DEMO/SONG] and

[PIANO/VOICE] simultaneously, and press [–L].

To set the pitch to 442.0 Hz:

Press and hold down the [DEMO/

SONG] and [PIANO/VOICE]

simultaneously, and press the A0 key.

To restore default pitch:

Press and hold down the [DEMO/SONG]

and [PIANO/VOICE] simultaneously, and

press [+R] and [–L] simultaneously.

Transposing the Pitch in Semitones

-5 -3 -1 0 +2 +4 +5

-6 -4 -2 +1

+3 +6

F♯2C3

Lowest key

F♯3

Transpose down Transpose up

Normal pitch

Fine-tuning the Pitch

Hz (Hertz)

This unit of measurement

refers to the frequency of a

sound and represents the

number of times a sound wave

vibrates in a second.

Setting range:

414.8 – 466.8 Hz

Default setting:

A3 = 440.0 Hz

Lowest key

Playing Various Musical Instrument Sounds (Voices)

CLP-525 Owner’s Manual

You can layer two Voices and play them simultaneously to create a more richly textured sound.

1. Engage the Dual mode.

While holding down [PIANO/VOICE], simultaneously hold down two keys

between C1 and A1 to select the two desired Voices. For information on which

Voices are assigned to the keys, refer to “Voice List” (page 17).

The Voice assigned to the lower key will be designated as Voice 1, and the Voice

assigned to the higher key will be designated as Voice 2. You cannot assign the same

Voice to both Voice 1 and Voice 2 simultaneously in Dual mode.

To shift the Octave for each Voice:

While holding down [PIANO/VOICE], press one of the C5 – F5 keys.

To adjust the Balance between two Voices:

While holding down [PIANO/VOICE], press one of the F♯5 – F♯6 keys. A setting

of “0” produces an equal balance between two Voices. Settings below “0” increase

the volume of Voice 2, while settings above “0” increase the volume of Voice 1, in

relation to the other.

2. To exit from Dual mode, press [PIANO/VOICE].

Layering Two Voices (Dual mode)

-5 -3 -1-1 00+2+1 +1 +4 +5

-60-4-2-1

+1 +3 +6

C5 F5

Highest key

C1 A1

Lowest key

F♯5C6 F♯6

Engaging

Dual mode

Shifting the octave

Adjusting the balance

Voice 1

Voice 2

NOTE

The Dual and Duo modes

(page 22) cannot be engaged

at the same time.

Playing Various Musical Instrument Sounds (Voices)

CLP-525 Owner’s Manual

This function allows two different players to play the instrument, one on the left and the other on the right,

over the same octave range.

1. While holding down [PIANO/VOICE], press [+R] and [–L]

simultaneously to engage Duo.

The keyboard is divided into two sections, with the E3 key as the Split Point.

2. One person should play the left section of the keyboard

while the other plays the right.

To shift the Octave for each Voice:

Same operation as in Dual (page 21).

To adjust the volume balance between two keyboard sections:

Same operation as in Dual (page 21).

Pedal function in Duo

Damper Pedal: Applies Sustain to the right section.

Sostenuto Pedal: Applies Sustain to both sections.

Soft Pedal: Applies Sustain to the left section.

3. To exit from Duo, simultaneously hold down [PIANO/

VOICE] and press [+R] and [–L].

Playing Duo

NOTE

Different Voices cannot be

assigned to the Right Voice

and Left Voice.

Split Point E3Equivalent to C3 (middle C) Equivalent to C3 (middle C)

Left Voice (Voice 2) Right Voice (Voice 1)

NOTE

The Split Point cannot be

changed from E3.

NOTE

If the keyboard is in Dual,

engaging Duo will exit from

Dual. The Voice 1 is used as

the Voice of the entire

keyboard.

CLP-525 Owner’s Manual

Song Playback and Practice

In addition to the Demo Songs, Preset Songs are provided for your listening pleasure.

1. Find the number of the Song that you want to play back

from the included “50 Greats for the Piano.”

The number of each piano Preset Song is assigned to the C2 – C♯6 keys.

2. While holding down [DEMO/SONG], press one of the C2 –

C♯6 keys to start playback.

The [PLAY], [+R] and [–L] lamps light, and playback continues the sequence:

starting with the selected song, the playback of the Preset Songs will continue. After

the last Preset Song, the sequence then returns to the first Preset Song and repeats

until you stop it.

To change the Preset Song during playback:

Press [+R] or [–L] to change to the next or previous Preset Song.

To change the tempo during playback:

Press [METRONOME] to start the Metronome, then press [+R] or [–L] to increase

or decrease the Tempo value by 1. Other instructions are the same as those of the

Metronome Tempo (page 15).

To play back from the beginning of the Song at the desired tempo for

practice:

During playback, press [+R] and [–L] simultaneously to jump to the playback

position at the beginning of the Song then continue playback at the last specified

tempo.

3. Press [DEMO/SONG] or [PLAY] to stop playback.

The [PLAY], [+R] and [–L] lamps turn off.

Listening to 50 Preset Songs

Highest key (C7)

Song 1 Song 10 Song 20 Song 30 Song 40

C3 C4 C5

Song 50 (C♯6)

NOTE

You can play the keyboard

along with the preset Song.

You can also change the Voice

playing on the keyboard.

NOTE

You can import additional

Songs by loading SMF files

from a computer. For details,

refer to the “Computer-related

Operations” on the website

(page 8).

Song Playback and Practice

CLP-525 Owner’s Manual

All the Songs except for the Demo (page 18) let you turn on or off the left-hand and right-hand Parts

individually. By turning off [+R], for example, you can practice the right-hand Part while the left-hand Part

is playing back, and vice versa.

1. Select a Preset Song (page 23) or the User Song (page 25).

2. While holding down [PLAY], press [+R] or [–L] to turn the

Part on/off.

Pressing the same button repeatedly while holding down [PLAY] toggles playback

on and off. The lamp of the button lights to indicate that the corresponding Part is

on.

3. Practice the Part which is turned off.

To change the Tempo:

If desired, you can change the tempo for your practice convenience. For details,

refer to page 15.

4. Press [PLAY] to stop playback.

This Quick Play feature enables you to specify whether a Song should play back

immediately from the very first note, or play back any silence or rests that exist

before the first note.

To turn on Quick Play:

Hold down [DEMO/SONG] and press the A♯-1 key to enable immediate

playback from the first note or first pedal operation.

To turn off Quick Play:

Hold down [DEMO/SONG] and press the lowest key (A-1) to play from the top

of the first measure (including a rest or blank).

Practicing a One-Hand Part

NOTE

Selecting another Song will

reset the on/off status.

or Lamp lights when Part is on.

Playing from the top of the bar including a rest or blank

Default setting:

A♯ -1

Lowest key

Lowest key (A-1)

CLP-525 Owner’s Manual

Recording Your Performance

This instrument lets you record your keyboard performance as the User Song. Up to two Parts (left-hand and

right-hand) can be recorded separately.

1. Select the desired Voice and other parameters, such as beat,

for recording.

For instructions on selecting a Voice, refer to page 17. If necessary, set other

parameters, such as beat and effects, in this step.

2. While holding down [REC], press [+R] or [–L] to engage

Record Ready mode for the Part you want to record.

If you do not intend to record right- and left-hand Parts separately, record the

entire performance to either Part.

Recording the right-hand Part ([+R])

Recording the left-hand Part ([–L])

After a while, the [REC] lamp and the selected Part lamp will flash at the current

tempo.

To exit from Record Ready mode:

Simply press [REC].

If data has already been recorded to the other Part:

The data in this Part will be played back while recording.

3. Play the keyboard or press [PLAY] to start recording.

The [REC] lamp lights up while the Recording Part lamp flashes at the current

tempo.

4. Press either [REC] or [PLAY] to stop recording.

The [REC], [PLAY], [+R] and [–L] lamps flash, indicating that the recorded data is

being stored. After the Save operation is completed, the lamps will turn off,

indicating that the Record operation has been completed.

5. If desired, record the other Part by repeating Steps 1 – 4.

6. To hear the recorded Song, press [PLAY] to start playback.

Press [PLAY] again to stop playback.

Recording Your Performance

About audio files

The Recording function of this

instrument will record your

keyboard performance as

MIDI data. Note that audio

recording is not available.

Recording Capacity

This instrument can record up

to 100 KB (approximately

11,000 notes).

NOTE

You can use the Metronome

while recording; however, the

Metronome sound will not be

recorded.

NOTICE

If a Part contains data, the

Part lamp lights. Note that

the Recording operation will

replace already-recorded

data with the new data.

NOTE

If the keyboard is in the Duo

mode (page 22), the data will

be recorded to each Part. The

Part for recording cannot be

specified.

NOTICE

Never turn off the power

while the recorded data is

being stored (while the

lamps are flashing).

Otherwise, all recorded data

will be lost.

NOTE

The recorded Song data can

be saved to a computer as a

Standard MIDI file (SMF). For

details, refer to the “Computer-

related Operations” on the

website (page 8).

Recording Your Performance

CLP-525 Owner’s Manual

The settings of the following parameters can be changed after the Record operation is completed.

• For individual Parts: Voice, Dual Voices, Reverb Depth

• For the entire Song: Tempo, Reverb Type

1. Make the settings of the above parameters.

2. While holding down [REC], press the desired Part button to

engage Record Ready mode.

In this status, do not press [PLAY] again or any key. Otherwise, the originally

recorded performance data will be deleted.

3. Press [REC] and [PLAY] to exit from Record Ready mode.

To delete the entire Song:

1. While holding down [REC], press [DEMO/SONG].

The [+R] and [–L] lamps flash.

To exit from this status, press [–L].

2. Press [+R] to delete the data of the entire Song.

The [REC], [PLAY], [+R] and [–L] lamps flash.

After the operation is completed, all lamps turn off.

To delete a specific Part:

1. While holding down [REC], press [+R] or [–L] (depending

on the Part you want to delete) to engage Record Ready

mode.

The [REC] and the selected Part ([+R] or [–L]) lamps flash.

2. Press [PLAY] to start recording without playing the

keyboard.

The selected Part ([+R] or [–L]) lamp flashes.

3. Press [REC] or [PLAY] to stop recording.

All data recorded for the selected Part will be deleted, and the lamp turns off.

Changing the Initial Settings of the Recorded Song

Deleting Recorded Data

CLP-525 Owner’s Manual

Backing up Data and Initializing the Settings

The following settings and data are maintained even if you turn the power off.

•Metronome Volume

•Metronome Beat

• Touch Sensitivity

•Tuning

• Intelligent Acoustic Control Depth

• Intelligent Acoustic Control On/Off

• Auto Power Off Enable/Disable

•User Song data

• Song data (SMF Files) loaded from a computer

Among the data listed above, only the User Song data can be transferred to a

computer and saved as an SMF file. For details, refer to the “Computer-related

Operations” on the website (page 8).

With Musicsoft Downloader (available for free downloading), up to 10 SMF files can be transferred from the

computer to the internal memory of this instrument, and vice versa. For details, refer to the “Computer-

related Operations” on the website (page 8).

With this operation, all data (with the exception of the Songs) will be reset to the

factory default settings.

To do this, simultaneously hold down the C7 (the highest) key and turn on the

power.

Data Maintained When Power is Turned Off

Saving the User Song data to a computer

NOTICE

Saved data may be lost due

to malfunction or incorrect

operation. Save important

data to an external device

such as a computer.

Transferring SMF Files Between a Computer and this Instrument

Initializing the Settings

NOTICE

Never turn off the power

while the Initialize operation

is being executed (that is,

while the [REC], [PLAY], [+R]

and [–L] lamps are flashing).

NOTE

If this instrument somehow

becomes disabled or

malfunctions, turn off the

power then execute

Initialization.

Highest key

CLP-525 Owner’s Manual

Appendix

Troubleshooting

Problem Possible Cause and Solution

Power suddenly and unexpectedly turns off.

This is normal and the Auto Power Off function may have been activated

(page 12). If desired, disable the Auto Power Off function.

The instrument does not turn on.

Securely insert the adaptor plugs into the socket on this instrument and into

a proper AC outlet (page 11).

A click or pop is heard when the power is

turned on or off.

This is normal when electrical current is being applied to the instrument.

Noise is heard from the speakers or

headphones.

The noise may be due to interference caused by the use of a mobile phone

in close proximity to this instrument. Turn off the mobile phone, or move it

further away from this instrument.

Noise is heard from the instrument’s speakers or

headphones when using the instrument with the

application on iPhone/iPad.

When you use the instrument along with the application on your iPhone/

iPad, we recommend that you set “Airplane Mode” to “ON” on your iPhone/

iPad in order to avoid noise caused by communication.

The overall volume is low, or no sound is heard.

The Master Volume is set too low. Set it to an appropriate level using the

[MASTER VOLUME] knob (page 13).

Make sure a pair of headphones is not connected to the headphones jack

(page 12).

Make sure that Local Control is On. For details, refer to the “MIDI

Reference” (page 8).

Pedals do not function.

The pedal cord may not be securely connected to the [TO PEDAL] jack. Be

sure to insert the pedal cord all the way until the metal part of the cord plug

disappears from view (page 30).

The damper pedal does not function as

expected.

The damper pedal was pressed when the power was turned on. This is not

a malfunction; release the pedal and press it again to reset the function.

CLP-525 Owner’s Manual

Keyboard Stand Assembly

CAUTION

• Assemble the unit on a hard and flat floor with ample space.

• Be careful not to confuse parts, and be sure to install all

parts in the correct orientation. Please assemble the unit in

accordance with the sequence given below.

• Assembly should be carried out by at least two persons.

• Be sure to use only the included screws of the specified

sizes. Do not use any other screws. Use of incorrect screws

can cause damage or malfunction of the product.

• Be sure to tighten all screws upon completing assembly of

the unit.

• To disassemble the unit, reverse the assembly sequence

given below.

Remove all parts from the package and make sure you

have all of the items.

1. Attach (finger-tighten) C to D and

1-1 Untie and straighten out the bundled pedal

cord.

Don’t discard the vinyl tie. You will need it later in

step 6.

1-2 Align D and E with each end of C.

1-3 Attach D and E to C by finger-tightening

the long screws (6 x 20 mm).

2. Attach B.

2-1 Align the screw holes on the upper side of B

with the bracket holes on D and E, then

attach the upper corners of B to D and E by

finger-tightening two thin screws (4 x 12

mm).

2-2 While pushing the lower part of D and E

from outside, secure the bottom ends of B

using two tapping screws (4 x 20 mm).

Have a Phillips-head (+) screwdriver of the appropriate size

ready.

Foamed styrol pads

Remove foamed styrol pads from the package, position them

on the floor, then place A on top of them. Position the pads so

that they will not hide the connectors on the bottom of A.

Bundled pedal cord inside

6 x 20 mm long screws x 4

4 x 12 mm thin screws x 2

4 x 20 mm tapping screws x 4

6 x 16 mm short screws x 6

Cord holders x 2

Power cord x 1

AC power adaptor x 1

The power cord and adaptor may

not be included, or may look

different from the illustration

above, depending on your

particular area. Please check with

your Yamaha dealer.

4 × 10 mm

thin screws x 2

Headphone hanger x 1

1-1

1-3

2-1

2-2

2-3

2-2

Keyboard Stand Assembly

CLP-525 Owner’s Manual

2-3 Insert the other two tapping screws (4 x 20

mm) into the other two screw holes to

secure B.

2-4 Securely tighten the screws on the top of B

that were attached in Step 2-1.

3. Secure C.

Securely tighten the screws on C that were

attached in Step 1-3.

4. Mount A.

Be sure to place your hands at least 15 cm away

from either end of the main unit when positioning

it.

CAUTION

• Be extra careful not to drop the main unit or let your fingers

be pinched by it.

• Do not hold the main unit in any position other than the

position specified above.

5. Secure A.

5-1 Adjust the position of A so that the left and

right ends of A will project beyond D and E

equally when seen from the front.

5-2 Secure A by tightening the short screws (6 x

16 mm) from the front.

6. Connect the pedal cord and the AC

power adaptor.

Align the screw holes.

At least 15 cm

5-1

5-2

6-1

6-2

6-3

6-5

Keyboard Stand Assembly

CLP-525 Owner’s Manual

6-1 Insert the pedal cord plug to the

[TO PEDAL] jack from the rear.

6-2 Attach the cord holders to the rear panel as

shown, then clip the cord into the holders.

6-3 Use a vinyl tie to take up any slack in the

pedal cord.

6-4 Connect one end of the power cord to the

power adaptor.

6-5 Insert the DC plug of the AC power adaptor

into the DC IN jack.

7. Set the adjuster.

Rotate the adjuster until it comes in firm contact

with the floor surface.

8. Attach the headphone hanger.

Use two thin screws (4 x 10 mm) to attach the

hanger as shown in the illustration.

When connecting the pedal

cord, insert the plug securely

until the metal part

disappears from view.

After completing the assembly, please check the

following.

• Are there any parts left over?

 Review the assembly procedure and correct any

errors.

• Is this instrument clear of doors and other

movable fixtures?

 Move the instrument to an appropriate location.

• Does this instrument make a rattling noise when

you shake it?

 Tighten all screws.

• Does the pedal box rattle or give way when you

step on the pedals?

 Turn the adjuster so that it is set firmly against the

floor.

• Are the pedal cord plug and the adaptor plug

inserted securely into the sockets?

 Check the connection.

• If the main unit creaks or is otherwise unsteady

when you play on the keyboard, refer to the

assembly diagrams and retighten all screws.

CAUTION

• When moving the instrument after assembly, always

hold the bottom of the main unit.

• Do not hold the key cover or top portion. Improper

handling can result in damage to the instrument or

personal injury.

Transporting

If you move to another location, you can transport the

instrument along with other belongings. You can move the

unit as it is (assembled), or you can disassemble the unit

down to the condition it was in when you first took it out of

the box. Transport the keyboard horizontally. Do not lean

it up against a wall or stand it up on its side. Do not subject

the instrument to excessive vibration or shock. When

transporting the assembled instrument, make sure all

screws are properly tightened and have not been loosened

by moving the instrument.

Do not hold here.

Hold here.

CLP-525 Owner’s Manual

Specifications

* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or

specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha

dealer.

Items CLP-525

Size/Weight

Width

[For models with polished finish]

1350 mm (53-1/8") [1353 mm (53-1/4")]

Height

[For models with polished finish]

Without Music Rest 845 mm (33-1/4") [848 mm (33-3/8")]

With Music Rest 999 mm (39-5/16") [1000 mm (39-3/8")]

Depth

[For models with polished finish]

Without Music Rest 414 mm (16-5/16") [415 mm (16-5/16")]

With Music Rest 414 mm (16-5/16") [415 mm (16-5/16")]

Weight

[For models with polished finish]

43.0 kg (94 lbs., 13 oz) [45.0 kg (99 lbs., 3 oz)]

Control Interface

Keyboard

Number of Keys 88

Type

GH3 (Graded Hammer 3) keyboard with synthetic ivory keytops

Touch Response Hard/Medium/Soft/Fixed

Pedal

Number of Pedals 3

Half Pedal Yes (Damper)

Functions Sustain, Sostenuto, Soft

Panel Language English

Cabinet

Key Cover Style Sliding

Music Rest Yes

Voices/

Tone Generation

Piano Sound Yamaha CFIIIS

Number of Polyphony (Max.) 256

Number of Voices 10

Effects/Functions

Reverb 4 types

Smooth Release Yes

Damper Resonance Yes

Dual Yes

Duo Yes

Intelligent Acoustic Control (IAC) Yes

Recording/Playback

(MIDI data only;

audio not supported)

Preset Number of Preset Songs 10 Demo Songs, 50 Piano Preset Songs

Recording

Number of Songs 1

Number of Tracks 2

Data Capacity (Max.) Approx. 100 KB/Song (Approx. 11,000 notes)

Compatible Data Format

Recording SMF (Format 0)

Playback SMF (Format 0 & 1)

Overall Controls

Metronome Yes

Tempo Range 5 – 280

Transpose -6 – 0 – +6

Tuning 414.8 – 440.0 – 466.8 Hz

Storage Internal Memory

Total maximum size approx. 900 KB

(User song: One song approx. 100 KB, Loading song data

from a computer: Up to 10 songs)

Connectivity

Headphones Yes (x 2)

USB TO HOST Yes

Sound System

Amplifiers 20 W x 2

Speakers Oval (12 cm x 6 cm) x 2

Acoustic Optimizer Yes

Power Supply

Power Consumption 13 W (when using the PA-300C)

Auto Power Off Yes (Approx. 30 minutes)

Accessories

• Owner’s Manual

• Quick Operation Guide

• “50 Greats for the Piano” (Music Book)

• Online Member Product Registration

• AC power adaptor: PA-300C or an equivalent

recommended by Yamaha*

• Power cord*

• Bench*

* Included or optional depending on your locale

Options (May not be available depending on your locale.)

• USB MIDI Interface for iPhone/iPod touch/iPad: i-UX1

• Headphones: HPE-160

• AC power adaptor: PA-300C or an equivalent

recommended by Yamaha

CLP-525 Owner’s Manual

Index

Numerics

50 Preset Songs ........................................................23

AC power adaptor .....................................................8

Accessories ..................................................................8

Auto Power Off ........................................................12

Beat ............................................................................15

Computer-related Operations .................................8

Damper Pedal ...........................................................14

Damper Resonance .................................................14

Delete .........................................................................26

Demo Song List ........................................................18

Demo Songs ..............................................................18

Dual mode ................................................................21

Duo ............................................................................22

Half-pedal .................................................................14

Headphones ..............................................................12

Hz (Hertz) .................................................................20

Initializing .................................................................27

Intelligent Acoustic Control (IAC) .......................13

Key Cover .................................................................10

Left-hand Part ..........................................................24

Manuals .......................................................................8

Metronome ...............................................................15

MIDI Basics ................................................................8

MIDI Reference .........................................................8

Octave ........................................................................21

Online Manuals (PDF) .............................................8

Panel Controls and Terminals ................................ 9

Pedals ........................................................................14

Pitch ..........................................................................20

Power ........................................................................11

Power indicator .......................................................11

Practice .....................................................................24

Preset Songs ............................................................. 23

Quick Operation Guide ............................................ 8

Quick Play ................................................................ 24

Recording .................................................................25

Reverb .......................................................................19

Reverb Depth ...........................................................19

Reverb Type .............................................................19

Reverb Type List ......................................................19

Right-hand Part .......................................................24

Soft Pedal .................................................................. 14

Sostenuto Pedal .......................................................14

Tempo .......................................................................15

Touch Sensitivity ..................................................... 16

Transpose .................................................................20

Tuning ......................................................................20

USB TO HOST .......................................................... 9

User Song .................................................................25

Voice .........................................................................17

Voice List ..................................................................17

Volume ...............................................................13, 15

MEMO

(bottom_en_01)

(bottom_fr_01)

For CLP-525 and AC Power Adaptor

(weee_eu_en_01)

(weee_eu_fr_01)

The model number, serial number, power requirements, etc.,

may be found on or near the name plate, which is at the bottom

of the unit. You should note this serial number in the space pro-

vided below and retain this manual as a permanent record of

your purchase to aid identification in the event of theft.

Model No.

Serial No.

Le numéro de modèle, le numéro de série, l'alimentation req-

uise, etc., se trouvent sur ou près de la plaque signalétique du

produit, située dans la partie inférieure de l'unité. Notez le

numéro de série dans l'espace fourni ci-dessous et conservez

ce manuel en tant que preuve permanente de votre achat afin

de faciliter l'identification du produit en cas de vol.

N° de modèle

N° de série

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic

products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in

accordance with your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative

effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste

disposal service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further

information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local

authorities or dealer and ask for the correct method of disposal.

Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques.

Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou

électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.

Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et

électroniques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation

nationale et aux Directives 2002/96/EC.

En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la

sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui

pourraient advenir lors d'un traitement inapproprié des déchets.

Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et

électroniques, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où

vous avez acheté les produits.

[Pour les professionnels dans l'Union Européenne]

Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre

vendeur ou fournisseur pour plus d'informations.

[Information sur le traitement dans d'autres pays en dehors de l'Union Européenne]

Ce symbole est seulement valable dans l'Union Européenne. Si vous souhaitez vous débarrasser de déchets

d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander

la méthode de traitement appropriée.

The name plate is located on the bottom of the unit.

La plaque signalétique de ce produit se trouve dans le

bas de l'unité.

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha

ou au distributeur le plus proche de vous figurant dans la liste suivante.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Toronto, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México, S.A. de C.V.

Av. Insurgentes Sur 1647 “Prisma Insurgentes”,

Col. San Jose Insurgentes, Del. Benito Juarez,

03900, Mexico, D.F.

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi,

CEP 04534-013 São Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.,

Sucursal Argentina

Olga Cossettini 1553, Piso 4 Norte,

Madero Este-C1107CEK

Buenos Aires, Argentina

Tel: 54-11-4119-7000

VENEZUELA

Yamaha Music Latin America, S.A.,

Sucursal Venezuela

C.C. Manzanares Plaza P4

Ofic. 0401- Manzanares-Baruta

Caracas Venezuela

Tel: 58-212-943-1877

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso No.7, Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, República de Panamá

Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND

Yamaha Music Europe GmbH (UK)

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, U.K.

Tel: 01908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH

Branch Switzerland in Zürich

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 044-387-8080

AUSTRIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/HUNGARY/

ROMANIA/SLOVAKIA/SLOVENIA

Yamaha Music Europe GmbH

Branch Austria (Central Eastern Europe Office)

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

POLAND/LITHUANIA/LATVIA/

ESTONIA

Yamaha Music Europe GmbH

Branch Poland Office

ul. Wrotkowa 14 02-553 Warsaw, Poland

Tel: 022-500-2925

BULGARIA

Dinacord Bulgaria LTD.

Bul.Iskarsko Schose 7 Targowski Zentar Ewropa

1528 Sofia, Bulgaria

Tel: 02-978-20-25

MALTA

Olimpus Music Ltd.

The Emporium, Level 3, St. Louis Street Msida

MSD06

Tel: 02133-2144

NETHERLANDS/BELGIUM/

LUXEMBOURG

Yamaha Music Europe Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Music Europe

7 rue Ambroise Croizat, Zone d'activites Pariest,

77183 Croissy-Beaubourg, France

Tel: 01-64-61-4000

ITALY

Yamaha Music Europe GmbH, Branch Italy

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha Music Europe GmbH Ibérica, Sucursal

en España

Ctra. de la Coruna km. 17,200, 28231

Las Rozas (Madrid), Spain

Tel: +34-91-639-88-88

GREECE

Philippos Nakas S.A. The Music House

147 Skiathou Street, 112-55 Athens, Greece

Tel: 01-228 2160

SWEDEN

Yamaha Music Europe GmbH Germany filial

Scandinavia

J. A. Wettergrensgata 1, Box 30053

S-400 43 Göteborg, Sweden

Tel: +46 31 89 34 00

DENMARK

Yamaha Music Europe GmbH, Tyskland – filial

Denmark

Generatorvej 6A, DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

F-Musiikki Oy

Kluuvikatu 6, P.O. Box 260,

SF-00101 Helsinki, Finland

Tel: 09 618511

NORWAY

Yamaha Music Europe GmbH Germany -

Norwegian Branch

Grini Næringspark 1, N-1361 Østerås, Norway

Tel: 67 16 78 00

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120, IS-128 Reykjavik,

Iceland

Tel: 525 5000

RUSSIA

Yamaha Music (Russia) LLC.

Room 37, bld. 7, Kievskaya street, Moscow,

121059, Russia

Tel: 495 626 5005

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

SOUTH AFRICA

Global Music Instruments

Unit 4, 130 Boeing Road East Bedfordview 2008

Postnet Suite 130, Private Bag X10020 Edenvale

1610, South Africa

Tel: 27-11-454-1131

OTHER AFRICAN COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jebel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

TURKEY/CYPRUS

Yamaha Music Europe GmbH

Merkezi Almanya Türkiye İstanbul Şubesi

Maslak Meydan Sokak No:5 Spring Giz Plaza

Bağımsız Böl. No:3, 34398 Şişli, İstanbul

Tel: +90-212-999-8010

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jebel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: 021-6247-2211

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 2737-7688

INDIA

Yamaha Music India Pvt. Ltd.

Spazedge building, Ground Floor, Tower A, Sector

47, Gurgaon- Sohna Road, Gurgaon, Haryana, India

Tel: 0124-485-3300

INDONESIA

PT. Yamaha Musik Indonesia (Distributor)

Yamaha Music Center Bldg. Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 021-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,

Kangnam-Gu, Seoul, Korea

Tel: 02-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn., Bhd.

No.8, Jalan Perbandaran, Kelana Jaya, 47301

Petaling Jaya, Selangor, Malaysia

Tel: 03-78030900

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music (Asia) Private Limited

Block 202 Hougang Street 21, #02-00,

Singapore 530202, Singapore

Tel: 65-6747-4374

TAIWAN

Yamaha Music & Electronics Taiwan Co.,Ltd.

3F, No.6, Section 2 Nan-Jing East Road, Taipei,

Taiwan R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

3, 4, 15 and 16th floor, Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: 02-215-2622

VIETNAM

Yamaha Music Vietnam Company Limited

15th Floor, Nam A Bank Tower, 201-203 Cach

Mang Thang Tam St., Ward 4, Dist.3,

Ho Chi Minh City, Vietnam

Tel: +84-8-3818-1122

OTHER ASIAN COUNTRIES

Yamaha Corporation

Market Development Section

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2312

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

NEW ZEALAND

Music Works LTD

P.O.BOX 6246 Wellesley, Auckland 4680,

New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation

Market Development Section

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2312

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

DMI7

C.S.G., DMI Development Division

312MWAP*.*-01B0

Printed in Vietnam

ZH76640

http://www.yamaha.com/

Yamaha Global Site

http://download.yamaha.com/

Yamaha Downloads

ZH76640

Transcripción de documentos

English Français Owner’s Manual Mode d’emploi CLP- 525 For information on assembling the keyboard stand, refer to the instructions at the end of this manual. EN Pour obtenir des informations sur l'assemblage du support du clavier, reportez-vous aux instructions à la fin de ce manuel. FR FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accesso- ries and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to com- ply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Com- pliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B) COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) OBSERVERA! Responsible Party : Yamaha Corporation of America Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620 Telephone : 714-522-9011 Type of Equipment : Digital Piano Model Name : CLP-525 ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt, sålænge netledningen sidder i en stikkontakt, som er tændt — også selvom der er slukket på apparatets afbryder. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den ar ansluten till vägguttaget, även om själva apparaten har stängts av. VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta. (standby) IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord (FCC DoC) For AC Power Adaptor This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (fcc_sengen-C) For AC Power Adaptor IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured makings identifying the terminals in your plug proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. CAN ICES-3 (B)/NMB-3(B) • This applies only to products distributed by Yamaha Canada Music Ltd. • Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée. (can_b_01) 2 CLP-525 Owner’s Manual (2 wires) SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind. The use of an extension cord is not recommended! If you must use an extension cord, the minimum wire size for a 25' cord (or less) is 18 AWG. NOTE: The smaller the AWG number, the larger the current handling capacity. For longer extension cords, consult a local electrician. This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please observe all safety markings and instructions that accompany the accessory product. SPECIFICATIONS SUBJECT TO CHANGE: The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units. This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for long periods of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. IMPORTANT: The louder the sound, the shorter the time period before damage occurs. Some Yamaha products may have benches and/or accessory mounting fixtures that are either supplied with the product or as optional accessories. Some of these items are designed to be dealer assembled or installed. Please make sure that benches are stable and any optional fixtures (where applicable) are well secured BEFORE using. Benches supplied by Yamaha are designed for seating only. No other uses are recommended. Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. This product may also use “household” type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that the charger is intended for the battery being charged. When installing batteries, never mix old batteries with new ones, and never mix different types of batteries. Batteries MUST be installed correctly. Mismatches or incorrect installation may result in overheating and battery case rupture. Warning: Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by the laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information. Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly. NAME PLATE LOCATION: The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate. You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase. NOTICE: Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following: Model Serial No. Purchase Date 92-BP (bottom) PLEASE KEEP THIS MANUAL CLP-525 Owner’s Manual 3 Table of Contents PRECAUTIONS .................................... 5 About the Manuals ................................ 8 Included Accessories ............................. 8 Panel Controls and Terminals .............. 9 Basic Operations Setting Up .............................................10 Key Cover ..................................................................10 Music Rest .................................................................10 Turning the Power On.............................................11 Auto Power Off.........................................................12 Using Headphones ...................................................12 Playing the Piano..................................13 Setting the Volume...................................................13 Intelligent Acoustic Control (IAC)........................13 Using the Pedals........................................................14 Using the Damper Resonance ................................14 Using the Metronome..............................................15 Changing the Touch Sensitivity .............................16 Advanced Operations Playing Various Musical Instrument Sounds (Voices)....................................17 Selecting a Voice .......................................................17 Listening to the Demo Songs ..................................18 Adding Variations to the Sound (Reverb) ............19 Transposing the Pitch in Semitones ......................20 Fine-tuning the Pitch ...............................................20 Layering Two Voices (Dual mode) ........................21 Playing Duo...............................................................22 Song Playback and Practice .................23 Listening to 50 Preset Songs....................................23 Practicing a One-Hand Part....................................24 Playing from the top of the bar including a rest or blank ...........................................................................24 4 CLP-525 Owner’s Manual Recording Your Performance ............. 25 Recording Your Performance ................................ 25 Changing the Initial Settings of the Recorded Song .................................................................................... 26 Deleting Recorded Data .......................................... 26 Backing up Data and Initializing the Settings ................................................. 27 Data Maintained When Power is Turned Off...... 27 Saving the User Song data to a computer............. 27 Transferring SMF Files Between a Computer and this Instrument......................................................... 27 Initializing the Settings............................................ 27 Appendix Troubleshooting .................................. 28 Keyboard Stand Assembly ................... 29 Specifications ....................................... 32 Index..................................................... 33 PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe and handy place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/AC power adaptor Water warning • Do not place the power cord near heat sources such as heaters or radiators. Also, do not excessively bend or otherwise damage the cord, or place heavy objects on it. • Only use the voltage specified as correct for the instrument. The required voltage is printed on the name plate of the instrument. • Use the specified adaptor (page 32) only. Using the wrong adaptor can result in damage to the instrument or overheating. • Do not expose the instrument to rain, use it near water or in damp or wet conditions, place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the instrument, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument inspected by qualified Yamaha service personnel. • Never insert or remove an electric plug with wet hands. • Check the electric plug periodically and remove any dirt or dust which may have accumulated on it. Fire warning • Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire. Do not open • This instrument contains no user-serviceable parts. Do not open the instrument or attempt to disassemble or modify the internal components in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. If you notice any abnormality • When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. Then have the device inspected by Yamaha service personnel. - The power cord or plug becomes frayed or damaged. - It emits unusual smells or smoke. - Some object has been dropped into the instrument. - There is a sudden loss of sound during use of the instrument. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following: Power supply/AC power adaptor Location • Do not connect the instrument to an electrical outlet using a multiple-connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet. • Do not place the instrument in an unstable position where it might accidentally fall over. • When removing the electric plug from the instrument or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. • When transporting or moving the instrument, always use two or more people. Attempting to lift the instrument by yourself may damage your back, result in other injury, or cause damage to the instrument itself. • Remove the electric plug from the outlet when the instrument is not to be used for extended periods of time, or during electrical storms. • Before moving the instrument, remove all connected cables, to prevent damage to the cables or injury to anyone who might trip over them. • When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. Assembly • Read carefully the attached documentation explaining the assembly process. Failure to assemble the instrument in the proper sequence might result in damage to the instrument or even injury. • Use only the stand specified for the instrument. When attaching the stand or rack, use the provided screws only. Failure to do so could cause damage to the internal components or result in the instrument falling over. DMI-5 1/2 CLP-525 Owner’s Manual 5 Connections • Before connecting the instrument to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum. • Be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level. • Do not use the instrument/device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. Using the bench (If included) • Do not place the bench in an unstable position where it might accidentally fall over. • Do not play carelessly with or stand on the bench. Using it as a tool or stepladder or for any other purpose might result in accident or injury. Handling caution • Do not insert a finger or hand in any gaps on the key cover or instrument. Also take care that the key cover does not pinch your finger. • Never insert or drop paper, metallic, or other objects into the gaps on the key cover, panel or keyboard. This could cause physical injury to you or others, damage to the instrument or other property, or operational failure. • Do not rest your weight on, or place heavy objects on the instrument, and do not use excessive force on the buttons, switches or connectors. • Only one person should sit on the bench at a time, in order to prevent the possibility of accident or injury. • If the bench screws become loose due to extensive long-term use, tighten them periodically using the included tool. • Keep special watch over any small children so that they don’t fall off the rear of the bench. Since the bench does not have a backrest, unsupervised use may result in accident or injury. Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed. Always turn the power off when the instrument is not in use. Even when the [ ] (Standby/On) switch is in standby status (power lamp is off), electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet. NOTICE To avoid the possibility of malfunction/damage to the product, damage to data, or damage to other property, follow the notices below.  Handling • Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise. When you use the instrument along with the application on your iPhone/iPad, we recommend that you set “Airplane Mode” to “ON” on your iPhone/iPad in order to avoid noise caused by communication. • Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation. (Verified operating temperature range: 5° – 40°C, or 41° – 104°F.) • Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard. • In the case of a model with a polished finish, bumping the surface of the instrument with metal, porcelain, or other hard objects can cause the finish to crack or peel. Use caution.  Instrument/Bench Maintenance To keep your Clavinova in optimum condition, we recommend that you periodically follow the maintenance points below. • When cleaning the instrument or bench, use a soft, dry or slightly damp cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths. Otherwise, it may become discolored or degraded. • If you are using a model with a polished finish, gently remove dust and dirt with a soft cloth. Do not wipe too hard since small particles of dirt can scratch the instrument's finish. To keep the surface polished, apply commercially available piano polisher to a soft cloth and wipe the instrument’s surface with it. Then, polish it with a separate cloth. Before using any piano polisher, make sure to read the instructions for proper usage. • During extreme changes in temperature or humidity, condensation may occur and water may collect on the surface of the instrument. If water is left, the wooden parts may absorb the water and be damaged. Make sure to wipe any water off immediately with a soft cloth. • As with an acoustic piano, pedals may become tarnished across the ages. When this occurs, polish the pedal with a compound designed for piano pedals. Before using the compound, make sure to read the instructions for proper usage.  Saving data • Saved data may be lost due to malfunction or incorrect operation. Save important data to an external device such as a computer (see the online manual, Computer-related Operations (page 8)). 6 DMI-5 CLP-525 Owner’s Manual 2/2 Information  About copyrights • Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use. • This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use others' copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.  About functions/data bundled with the instrument • Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the original.  About this manual • The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your instrument. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.  Tuning • Unlike an acoustic piano, this instrument does not need to be tuned by an expert (although the pitch can be user-adjusted to match other instruments). This is because the pitch of digital instruments is always maintained perfectly. About audio files This instrument does not feature audio file playback or audio recording. In addition, audio signals created via your keyboard performance are not transmitted to your computer or iPad/iPhone, even if one of them is connected to the [USB TO HOST] terminal of the instrument. CLP-525 Owner’s Manual 7 Thank you for choosing the Yamaha Clavinova. In order to make the most of the performance potential and features of the instrument, please read the manuals thoroughly, and keep them in a handy place for later reference. About the Manuals Included Accessories This instrument has the following manuals. • Owner’s Manual (this book)  Included Manuals • Quick Operation Guide (separate sheet) Owner’s Manual (this book) Explains how to use the instrument. Quick Operation Guide (separate sheet) Shows in chart form the functions assigned to the buttons and the keyboard for quick understanding.  Online Manuals (PDF) Computer-related Operations Includes instructions on connecting this instrument to a computer, and operations related to transferring song data. MIDI Reference Contains the MIDI Data Format and MIDI Implementation chart, as well as descriptions on MIDI functions such as MIDI channel and Local Control settings. MIDI Basics (only in English, French and German) Contains basic explanations about MIDI. To obtain these manuals, access the Yamaha Downloads website, select your country, enter “CLP-525” in the Model Name box, then click [SEARCH]. Yamaha Downloads http://download.yamaha.com/ 8 CLP-525 Owner’s Manual • “50 Greats for the Piano” (music book) • Online Member Product Registration*1 • AC power adaptor*2 • Power cord*2 • Bench*2 *1 You will need the PRODUCT ID on the sheet in order to fill out the User Registration form. *2 May not be included depending on your particular area. Please check with your Yamaha dealer. Panel Controls and Terminals 1 3 9 4 5 2 6 7 $ 8 Rear Rear ) (Keyboard side) 1 Rear @ ! (Keyboard side) (Keyboard side) [P] (Standby/On) switch......................... page 11 9 For turning the power on or setting to standby. 2 [MASTER VOLUME] knob ..................... page 13 [DEMO/SONG] button..................... pages 18, 23 ) [PIANO/VOICE] button............. pages 17, 19, 21 ! [METRONOME] button .......................... page 15 NOTICE For starting or stopping the metronome. 6 7 Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used. [+R], [–L] buttons ....................... pages 17, 20, 24 • In general, these are for selecting the next or previous Voice. • During Song playback, these are for selecting the next or previous Song, and (while holding down [PLAY]) turning on/off the right-hand and lefthand Parts individually. • During Metronome playback, these are for increasing or decreasing the Tempo. [USB TO HOST] terminal For connecting to a computer. For details, refer to the “Computer-related Operations” on the website (page 8). For selecting a single Voice, two Voices for layering or a Reverb Type. 5 [PHONES] jacks....................................... page 12 For connecting a set of standard stereo headphones. For playing the Demo Songs and the Preset Songs. 4 [FUNCTION] .......................................... page 20 Simultaneously holding these two buttons and pressing the specified key sets will set the MIDI or Transpose parameters. For adjusting the volume of the entire sound. 3 # @ [TO PEDAL] jack ..................................... page 30 For connecting the pedal cord. # DC IN jack................................................ page 11 For connecting the power adaptor. $ Pedals ....................................................... page 14 For controlling expression and sustain, just as on an acoustic piano. [REC] button ............................................ page 25 For recording your keyboard performance. 8 [PLAY] button.......................................... page 25 For playing back the recorded performance. CLP-525 Owner’s Manual 9 Basic Operations Setting Up Key Cover To open the key cover: Lift the cover slightly, then push and slide it to the end. To close the key cover: Slide the cover toward you and gently lower the cover over the keys. CAUTION • Hold the cover with both hands when opening or closing it. Do not release it until it is fully opened or closed. Be careful to avoid catching fingers (yours or others, especially children’s) between the cover and the main unit. • Do not place objects, such as a piece of metal or paper, on top of the key cover. Small objects placed on the key cover may fall inside the unit when the cover is opened and may be nearly impossible to remove. This could cause electric shock, short circuit, fire or other serious damage to the instrument. CAUTION Be careful to avoid catching your fingers when opening or closing the cover. Music Rest To raise the music rest: 1. 2. 3. Pull the music rest up and toward yourself as far as it will go. 3 1 Flip down the two metal supports at the left and right on the rear of the music rest. 2 Lower the music rest so that it rests on the metal supports. To lower the music rest: 1. 2. 3. Pull the music rest toward yourself as far as it will go. Raise the two metal supports (at the rear of the music rest). 1 3 2 Gently lower the music rest backward until it is all the way down. CAUTION Do not try to use the music rest in a half-raised position. When lowering the music rest, do not release your hands from the music rest until it is all the way down. 10 CLP-525 Owner’s Manual Setting Up Turning the Power On 1. Connect the plugs of the AC power adaptor in the order shown in the illustration. DC IN jack (page 9) 1-2 AC power adaptor 1-1 1-3 Power cord AC outlet The shape of the plug and outlet differ depending on locale. WARNING • Use the specified adaptor (page 32) only. The use of other adaptors may result in irreparable damage to both the adaptor and the instrument. • The AC power adaptor is designed for indoor use only. Do not use in any wet environments. CAUTION Remove the AC plug from the AC outlet when the instrument is not to be used for extended periods of time, or during electrical storms. NOTE Follow this procedure in reverse order when disconnecting the power adaptor. 2. Press the [P] (Standby/On) switch to turn the power on. [P] (Standby/On) switch Power indicator Power indicator If you close the key cover without turning the power to standby, the power indicator remains lit, indicating that the power is still on. When you’re ready to turn the power to standby, press the [P] (Standby/On) switch again for a second. The power indicator turns off. CAUTION Even when the [P] (Standby/On) switch is in the standby status, electricity is still flowing to the instrument at a minimum level. When not using the instrument for an extended period of time, be sure to unplug the power cord from the wall AC outlet. CLP-525 Owner’s Manual 11 Setting Up Auto Power Off To prevent unnecessary power consumption, this instrument features an Auto Power Off function that automatically turns the power off if the instrument is not operated for approximately 30 minutes. If you do not want to use the Auto Power Off function, disable the function as described below. The setting (disabled or enabled) is retained even if the power is turned off. Default setting: Enable Disabling Auto Power Off Turn the power of the instrument off. Then, while holding down the lowest key, press the [P] (Standby/On) switch to turn on the power again so that the [REC] indicator flashes three times, indicating that the Auto Power Off function has been disabled. Lowest key You can also disable the Auto Power Off function without turning the power off, by simultaneously holding down [DEMO/SONG] and [PIANO/VOICE] and pressing the A♯5 key. A♯5 Highest key Re-enabling Auto Power Off To enable the Auto Power Off function again, simultaneously hold down [DEMO/SONG] and [PIANO/ VOICE] and press the A5 key. A5 Using Headphones Since this instrument is equipped with two [PHONES] jacks, you can connect two sets of standard stereo headphones. If you are using only one set of headphones, insert a plug into either jack, which automatically shuts off the speakers. CAUTION Do not use headphones at a high volume for an extended period of time; doing so may cause hearing loss. Using the headphone hanger PHONES You can hang the headphones on this instrument. Refer to “Keyboard Stand Assembly” on page 29 for instructions on installing the headphone hanger. Bottom surface NOTICE Do not hang anything other than the headphones on the hanger. Doing so may damage this instrument or the hanger. 12 CLP-525 Owner’s Manual Standard stereo phone plug Highest key Playing the Piano Setting the Volume When you start playing, use the [MASTER VOLUME] knob to adjust the volume of the entire keyboard sound. Level decreases. Level increases. CAUTION Do not use this instrument at a high volume level for a long period of time, or your hearing may be damaged. Intelligent Acoustic Control (IAC) With this function, the sound quality of this instrument is automatically adjusted and controlled according to the overall volume. Even when the volume is low, this lets you hear both low sounds and high sounds clearly. Default setting: On To turn on IAC: While holding down [PIANO/VOICE], press the F♯0 key. Lowest key F♯0 To turn off IAC: While holding down [PIANO/VOICE], press the F0 key. To adjust IAC Depth: While holding down [PIANO/VOICE], press one of the A-1 – D♯0 keys. Lowest key A-1: depth -3 Lowest key F0 D♯0: depth +3 C0: depth 0 (Standard setting) The higher the value, the more clearly that low and high sounds are heard at lower volume levels. Setting range: A-1 (-3) – D♯0 (+3) Default setting: C0 (0) CLP-525 Owner’s Manual 13 Playing the Piano Using the Pedals Damper Pedal (Right) Pressing this pedal will sustain notes longer. Releasing this pedal immediately stops (damps) any sustained notes. This pedal also features a “half-pedal” function that creates partial sustain effects, depending on how far down you press the pedal. NOTE If the damper pedal doesn’t work, make sure that the pedal cord is properly plugged into the main unit (page 30). Half-pedal function When you press the damper pedal here, this note and the notes you play before you release the pedal sustain longer. Sostenuto Pedal (Center) Pressing this pedal while holding the notes will sustain the pressed notes (as if the Damper Pedal had been pressed), but all subsequently played notes will not be sustained. This makes it possible to sustain a chord or single low note, for example, while the other notes are played “staccato.” This function allows you to vary the sustain length depending on how far the pedal is pressed. The farther down you press the pedal, the more the sound sustains. For example, if you press the damper pedal and all notes you are playing sound a bit murky and loud with too much sustain, you can release the pedal half way or higher to decrease the sustain (murkiness). NOTE When you press the sostenuto pedal here while holding the note, the note will sustain as long as you hold the pedal. Soft Pedal (Left) While the sostenuto pedal is held, the organ and strings Voices sound continuously without decay after the notes have been released. Pressing this pedal will reduce the volume and slightly change the timbre of the notes. The notes played before this pedal is pressed are not affected. When you select the Jazz Organ Voice, pressing the left pedal switches between fast/slow rotation of the rotary speaker (page 17). Using the Damper Resonance The Damper Resonance effect simulates the sustain sound of the damper pedal on a grand piano, as if you were pressing the damper pedal and playing the keyboard. This effect is applied to the entire sound of the instrument. To turn on the Damper Resonance: Default setting: On While holding [PIANO/VOICE], press the G♯2 key. To turn off the Damper Resonance: While holding [PIANO/VOICE], press the G2 key. Lowest key 14 CLP-525 Owner’s Manual G2 G♯2 (Off) (On) Playing the Piano Using the Metronome The metronome feature is convenient for practicing with an accurate tempo. 1. 2. Press [METRONOME] to start the Metronome. Press [METRONOME] to stop the Metronome. Adjusting the Metronome Volume Selecting a Beat Adjusting the Tempo C♯3 D♯3 2 4 7 9 11 14 16 A♯4 C♯5 1 3 19 1 3 5 6 8 10 12 13 15 17 18 20 Lowest key C1 G2 6 8 0 2 4 5 7 9 C3 D3 E3 F3 C4 Selecting a Beat While holding down [METRONOME], press one of the C3 – F3 keys. Key Beat C3 0 C♯3 2 D3 3 D♯3 4 E3 5 F3 6 Highest key F4 A4 B4 C5 D5 Default setting: 0 (C3) Adjusting the Tempo The Metronome tempo can be set from 5 to 280 beats per minute. • To increase or decrease the value by 1: While the metronome is playing, press [+R] to increase or [–L] to decrease. Alternatively, press and hold down [METRONOME], and press the C♯5 key to increase or B4 key to decrease. • To increase or decrease the value by 10: While holding down [METRONOME], press the D5 key to increase or the A♯4 key to decrease. • To specify a three-digit value: While holding down [METRONOME], press the relevant C4 – A4 keys one by one in order. For example to specify “95,” press the C4 (0), A4 (9) and F4 (5) keys in order. Resetting the value to the default (120) While holding down [METRONOME], press the [+R] and [–L] simultaneously, or press the C5 (default) key. Adjusting the Volume While holding down [METRONOME], press one of the keys between C1 and G2 to set the volume of the metronome. Pressing a higher key results in higher volume, while pressing a lower key results in lower volume. Setting range: C1 (1) – G2 (20) Default setting: D2 (15) CLP-525 Owner’s Manual 15 Playing the Piano Changing the Touch Sensitivity You can specify the Touch Sensitivity (how the sound responds to the way you play the keys). While holding down [PIANO/VOICE], press one of the A6 – C7 keys. A♯6 NOTE This setting is disabled with some Voices, such as an organ sound. Default setting: B6 (Medium) A6 Highest key (C7) B6 16 Key Touch Sensitivity Description A6 Fixed The volume level does not change at all regardless of whether you play the keyboard soft or hard. A♯6 Soft B6 Medium C7 Hard CLP-525 Owner’s Manual The volume level does not change much when you play the keyboard soft or hard. This is the standard piano touch response. The volume level changes very widely from pianissimo to fortissimo to facilitate dynamic and dramatic expression. You have to hit the keys hard to produce a loud sound. Advanced Operations Playing Various Musical Instrument Sounds (Voices) Selecting a Voice To select “Grand Piano 1”: NOTE Simply press [PIANO/VOICE]. To hear the characteristics of the Voices, play back the Demo Songs (page 18). To select another Voice: After pressing [PIANO/VOICE], press [+R] or [–L] to select the next or previous Voice. To select a specific Voice: While holding down [PIANO/VOICE], press one of the C1 – A1 keys. For details on which Voice is assigned to each key, see the list below. C♯1 Lowest key D♯1 F♯1 G♯1 C1 D1 E1 F1 G1 A1 Voice List Key Voice Name Voice description C1 Grand Piano 1 This sound was sampled from a full concert grand piano. It uses different samples depending on the strength of your playing and produces smoother tonal changes. Suitable not only for classical compositions but also for piano pieces of any style. C♯1 Grand Piano 2 Warm and soft piano sound. Good for playing ballads. D1 Grand Piano 3 Spacious and clear piano with bright reverb. Good for popular music. D♯1 E.Piano 1 An electronic piano sound created by FM synthesis. Good for standard popular music. E1 E.Piano 2 The sound of an electric piano using hammer-struck metallic “tines.” Soft tone when played lightly, and an aggressive tone when played hard. F1 Harpsichord The definitive instrument for baroque music. Since harpsichord uses plucked strings, there is no touch response. There is, however, a characteristic additional sound when the keys are released. F♯1 Vibraphone Vibraphone played with relatively soft mallets. The tone becomes more metallic the harder you play. G1 Pipe Organ This is a typical pipe organ sound (8 feet + 4 feet + 2 feet). Good for sacred music from the Baroque period. G♯1 Jazz Organ The sound of a “tonewheel” type electric organ. Often heard in jazz and rock music. The rotary speed of the rotary speaker effect can be switched by using the left pedal. Strings Stereo-sampled, large-scale strings ensemble with realistic reverb. Try combining this Voice with piano in the Dual mode. A1 CLP-525 Owner’s Manual 17 Playing Various Musical Instrument Sounds (Voices) Listening to the Demo Songs Special individual Demo Songs are provided for all of the instrument Voices. 1. Press [DEMO/SONG] to start playback. NOTE The [PLAY] lamp flashes, and the Demo Song for the current Voice starts. Starting with the selected song, the playback of the Demo Songs will continue. After the last demo song, the sequence then returns to the first Demo Song and repeats until you stop it. If you want to change the playback tempo, see page 15. To change the Demo Song during playback: Press the [+R] or [–L] to change to the next or previous Demo Song. To change to a specific Demo Song, press and hold down the [DEMO/SONG], then press one of the C1 – A1 keys. Lowest key 2. C1 F1 A1 Press [DEMO/SONG] or [PLAY] to stop playback. The [PLAY] lamp turns off. Demo Song List Key Voice Name Title Composer C1 Grand Piano 1 Bargarolle op. 60 F. F. Chopin C♯1 Grand Piano 2 Von fremden Landern und Menchen, Kinderszenen op. 15-1 R. Schumann D1 Grand Piano 3 Original Original D♯1 E.Piano 1 Original Original E1 E.Piano 2 Original Original F1 Harpsichord Concerto a cembalo obbligato, 2 violini, viola e continuo No. 7, BWV. 1058 J. S. Bach F♯1 Vibraphone Original Original G1 Pipe Organ Herr Christ, der ein’ge Gottes-Sohn, BWV. 601 J. S. Bach G♯1 Jazz Organ Original Original Strings Original Original A1 The Demo Songs excluding original Songs are short rearranged excerpts from the original compositions. The original Demo Songs are Yamaha originals (©2013 Yamaha Corporation). 18 CLP-525 Owner’s Manual Playing Various Musical Instrument Sounds (Voices) Adding Variations to the Sound (Reverb) This instrument features several Reverb Types that add extra depth and expression to the sound to create a realistic acoustic ambience. The appropriate Reverb Type and Depth are called up automatically when you select each of the Voices and Songs. This is why the Reverb Type need not be selected; however, you can change it if desired. To select a Reverb Type: Reverb in Dual Mode While holding down [PIANO/VOICE], press one of the C2 – E2 keys. An optimum reverb type for the combination of Voices is assigned automatically. Selecting a Reverb Type C♯2 Lowest key C2 D2 Adjusting Reverb Depth D♯2 E2 G♯4: depth 20 C3: depth 0 A4 Highest key The depth value increases as you press higher keys. Reverb Type List Key Reverb Type Description C2 Recital Hall Simulates the clear reverb sound you would hear in a mediumsized concert hall for piano recitals. C♯2 Concert Hall Simulates the gorgeous reverb sound you would hear in a large concert hall for orchestral performances. D2 Chamber D♯2 Club E2 Off Suitable for playing chamber music; simulates the intimate reverb sound you would hear in a spacious room, such as for classical music recitals. Simulates the vivid reverb sound you would hear in a live music venue or a jazz club. No effect is applied. To adjust Reverb Depth: While holding down [PIANO/VOICE], press one of the C3 – G♯4 keys. The Depth value increases as you press higher keys. Reverb Depth range: 0 (no effect) – 20 (maximum depth) While holding down [PIANO/VOICE], press the A4 key to set the Reverb Depth to the most suitable value for the current Voice. CLP-525 Owner’s Manual 19 Playing Various Musical Instrument Sounds (Voices) Transposing the Pitch in Semitones You can shift the pitch of the entire keyboard up or down in semitones in order to facilitate playing in difficult key signatures, or to easily match the pitch of the keyboard to the range of a singer or other instruments. For example, if “+5” is selected, playing key C produces pitch F, letting you play a song of F major as though it were in C major. To transpose the pitch down: While holding down [DEMO/SONG] and [PIANO/VOICE], press a key between F♯2 (-6) and B2 (-1). To transpose the pitch up: While holding down [DEMO/SONG] and [PIANO/VOICE], press a key between C♯3 (+1) and F♯3 (+6). To restore the normal pitch: While holding down [DEMO/SONG] and [PIANO/VOICE], press the C3 key. F♯2 -6 -4 -2 C3 F♯3 +1 +3 +6 -5 -3 -1 0 +2 +4 +5 Lowest key Transpose down Transpose up Normal pitch Fine-tuning the Pitch You can fine-tune the pitch of the entire instrument in about 0.2 Hz steps. This lets you match the keyboard pitch finely to that of other instruments or CD music. Hz (Hertz) To tune up (in about 0.2 Hz steps): This unit of measurement refers to the frequency of a sound and represents the number of times a sound wave vibrates in a second. Press and hold down the [DEMO/SONG] and [PIANO/VOICE] simultaneously, and press [+R]. Setting range: To tune down (in about 0.2 Hz steps): 414.8 – 466.8 Hz Press and hold down the [DEMO/SONG] and [PIANO/VOICE] simultaneously, and press [–L]. Default setting: A3 = 440.0 Hz To set the pitch to 442.0 Hz: Press and hold down the [DEMO/ SONG] and [PIANO/VOICE] simultaneously, and press the A0 key. Lowest key To restore default pitch: Press and hold down the [DEMO/SONG] and [PIANO/VOICE] simultaneously, and press [+R] and [–L] simultaneously. 20 CLP-525 Owner’s Manual A0 Playing Various Musical Instrument Sounds (Voices) Layering Two Voices (Dual mode) You can layer two Voices and play them simultaneously to create a more richly textured sound. 1. Engage the Dual mode. While holding down [PIANO/VOICE], simultaneously hold down two keys between C1 and A1 to select the two desired Voices. For information on which Voices are assigned to the keys, refer to “Voice List” (page 17). Adjusting the balance C1 A1 C5 F5 0 -1 F♯5 C6 -6 -4 -2 F♯6 +1 +3 +6 -1 +1 0 +1 -5 -3 -1 0 +2 +4 +5 Lowest key Engaging Dual mode Voice 1 Voice 2 Highest key Shifting the octave The Voice assigned to the lower key will be designated as Voice 1, and the Voice assigned to the higher key will be designated as Voice 2. You cannot assign the same Voice to both Voice 1 and Voice 2 simultaneously in Dual mode. NOTE The Dual and Duo modes (page 22) cannot be engaged at the same time. To shift the Octave for each Voice: While holding down [PIANO/VOICE], press one of the C5 – F5 keys. To adjust the Balance between two Voices: While holding down [PIANO/VOICE], press one of the F♯5 – F♯6 keys. A setting of “0” produces an equal balance between two Voices. Settings below “0” increase the volume of Voice 2, while settings above “0” increase the volume of Voice 1, in relation to the other. 2. To exit from Dual mode, press [PIANO/VOICE]. CLP-525 Owner’s Manual 21 Playing Various Musical Instrument Sounds (Voices) Playing Duo This function allows two different players to play the instrument, one on the left and the other on the right, over the same octave range. 1. While holding down [PIANO/VOICE], press [+R] and [–L] simultaneously to engage Duo. The keyboard is divided into two sections, with the E3 key as the Split Point. Equivalent to C3 (middle C) Split Point E3 Left Voice (Voice 2) 2. Right Voice (Voice 1) One person should play the left section of the keyboard while the other plays the right. NOTE To shift the Octave for each Voice: NOTE To adjust the volume balance between two keyboard sections: Same operation as in Dual (page 21). Pedal function in Duo Damper Pedal: Applies Sustain to the right section. Sostenuto Pedal: Applies Sustain to both sections. Soft Pedal: Applies Sustain to the left section. 22 Different Voices cannot be assigned to the Right Voice and Left Voice. Equivalent to C3 (middle C) Same operation as in Dual (page 21). 3. NOTE To exit from Duo, simultaneously hold down [PIANO/ VOICE] and press [+R] and [–L]. CLP-525 Owner’s Manual The Split Point cannot be changed from E3. If the keyboard is in Dual, engaging Duo will exit from Dual. The Voice 1 is used as the Voice of the entire keyboard. Song Playback and Practice Listening to 50 Preset Songs In addition to the Demo Songs, Preset Songs are provided for your listening pleasure. 1. Find the number of the Song that you want to play back from the included “50 Greats for the Piano.” The number of each piano Preset Song is assigned to the C2 – C♯6 keys. 2. While holding down [DEMO/SONG], press one of the C2 – C♯6 keys to start playback. Song 1 Song 10 Song 20 Song 30 Song 40 Song 50 (C♯6) NOTE You can play the keyboard along with the preset Song. You can also change the Voice playing on the keyboard. C2 C3 C4 C5 Highest key (C7) The [PLAY], [+R] and [–L] lamps light, and playback continues the sequence: starting with the selected song, the playback of the Preset Songs will continue. After the last Preset Song, the sequence then returns to the first Preset Song and repeats until you stop it. To change the Preset Song during playback: NOTE Press [+R] or [–L] to change to the next or previous Preset Song. You can import additional Songs by loading SMF files from a computer. For details, refer to the “Computer-related Operations” on the website (page 8). To change the tempo during playback: Press [METRONOME] to start the Metronome, then press [+R] or [–L] to increase or decrease the Tempo value by 1. Other instructions are the same as those of the Metronome Tempo (page 15). To play back from the beginning of the Song at the desired tempo for practice: During playback, press [+R] and [–L] simultaneously to jump to the playback position at the beginning of the Song then continue playback at the last specified tempo. 3. Press [DEMO/SONG] or [PLAY] to stop playback. The [PLAY], [+R] and [–L] lamps turn off. CLP-525 Owner’s Manual 23 Song Playback and Practice Practicing a One-Hand Part All the Songs except for the Demo (page 18) let you turn on or off the left-hand and right-hand Parts individually. By turning off [+R], for example, you can practice the right-hand Part while the left-hand Part is playing back, and vice versa. 1. 2. Select a Preset Song (page 23) or the User Song (page 25). While holding down [PLAY], press [+R] or [–L] to turn the Part on/off. NOTE Selecting another Song will reset the on/off status. Pressing the same button repeatedly while holding down [PLAY] toggles playback on and off. The lamp of the button lights to indicate that the corresponding Part is on. or 3. Lamp lights when Part is on. Practice the Part which is turned off. To change the Tempo: If desired, you can change the tempo for your practice convenience. For details, refer to page 15. 4. Press [PLAY] to stop playback. Playing from the top of the bar including a rest or blank This Quick Play feature enables you to specify whether a Song should play back immediately from the very first note, or play back any silence or rests that exist before the first note. To turn on Quick Play: Hold down [DEMO/SONG] and press the A♯-1 key to enable immediate playback from the first note or first pedal operation. A♯-1 Lowest key To turn off Quick Play: Hold down [DEMO/SONG] and press the lowest key (A-1) to play from the top of the first measure (including a rest or blank). Lowest key (A-1) 24 CLP-525 Owner’s Manual Default setting: On Recording Your Performance This instrument lets you record your keyboard performance as the User Song. Up to two Parts (left-hand and right-hand) can be recorded separately. Recording Your Performance 1. Select the desired Voice and other parameters, such as beat, for recording. For instructions on selecting a Voice, refer to page 17. If necessary, set other parameters, such as beat and effects, in this step. 2. While holding down [REC], press [+R] or [–L] to engage Record Ready mode for the Part you want to record. If you do not intend to record right- and left-hand Parts separately, record the entire performance to either Part. Recording the right-hand Part ([+R]) or Recording the left-hand Part ([–L]) About audio files The Recording function of this instrument will record your keyboard performance as MIDI data. Note that audio recording is not available. Recording Capacity This instrument can record up to 100 KB (approximately 11,000 notes). NOTE You can use the Metronome while recording; however, the Metronome sound will not be recorded. NOTICE If a Part contains data, the Part lamp lights. Note that the Recording operation will replace already-recorded data with the new data. NOTE After a while, the [REC] lamp and the selected Part lamp will flash at the current tempo. If the keyboard is in the Duo mode (page 22), the data will be recorded to each Part. The Part for recording cannot be specified. To exit from Record Ready mode: Simply press [REC]. If data has already been recorded to the other Part: The data in this Part will be played back while recording. 3. Play the keyboard or press [PLAY] to start recording. The [REC] lamp lights up while the Recording Part lamp flashes at the current tempo. 4. 5. 6. Press either [REC] or [PLAY] to stop recording. NOTICE The [REC], [PLAY], [+R] and [–L] lamps flash, indicating that the recorded data is being stored. After the Save operation is completed, the lamps will turn off, indicating that the Record operation has been completed. Never turn off the power while the recorded data is being stored (while the lamps are flashing). Otherwise, all recorded data will be lost. If desired, record the other Part by repeating Steps 1 – 4. NOTE To hear the recorded Song, press [PLAY] to start playback. Press [PLAY] again to stop playback. The recorded Song data can be saved to a computer as a Standard MIDI file (SMF). For details, refer to the “Computerrelated Operations” on the website (page 8). CLP-525 Owner’s Manual 25 Recording Your Performance Changing the Initial Settings of the Recorded Song The settings of the following parameters can be changed after the Record operation is completed. • For individual Parts: Voice, Dual Voices, Reverb Depth • For the entire Song: Tempo, Reverb Type 1. 2. Make the settings of the above parameters. While holding down [REC], press the desired Part button to engage Record Ready mode. In this status, do not press [PLAY] again or any key. Otherwise, the originally recorded performance data will be deleted. 3. Press [REC] and [PLAY] to exit from Record Ready mode. Deleting Recorded Data To delete the entire Song: 1. While holding down [REC], press [DEMO/SONG]. The [+R] and [–L] lamps flash. To exit from this status, press [–L]. 2. Press [+R] to delete the data of the entire Song. The [REC], [PLAY], [+R] and [–L] lamps flash. After the operation is completed, all lamps turn off. To delete a specific Part: 1. While holding down [REC], press [+R] or [–L] (depending on the Part you want to delete) to engage Record Ready mode. The [REC] and the selected Part ([+R] or [–L]) lamps flash. 2. Press [PLAY] to start recording without playing the keyboard. The selected Part ([+R] or [–L]) lamp flashes. 3. Press [REC] or [PLAY] to stop recording. All data recorded for the selected Part will be deleted, and the lamp turns off. 26 CLP-525 Owner’s Manual Backing up Data and Initializing the Settings Data Maintained When Power is Turned Off The following settings and data are maintained even if you turn the power off. • Metronome Volume • Metronome Beat • Touch Sensitivity • Tuning • Intelligent Acoustic Control Depth • Intelligent Acoustic Control On/Off • Auto Power Off Enable/Disable • User Song data • Song data (SMF Files) loaded from a computer Saving the User Song data to a computer Among the data listed above, only the User Song data can be transferred to a computer and saved as an SMF file. For details, refer to the “Computer-related Operations” on the website (page 8). NOTICE Saved data may be lost due to malfunction or incorrect operation. Save important data to an external device such as a computer. Transferring SMF Files Between a Computer and this Instrument With Musicsoft Downloader (available for free downloading), up to 10 SMF files can be transferred from the computer to the internal memory of this instrument, and vice versa. For details, refer to the “Computerrelated Operations” on the website (page 8). Initializing the Settings With this operation, all data (with the exception of the Songs) will be reset to the factory default settings. To do this, simultaneously hold down the C7 (the highest) key and turn on the power. C7 Highest key NOTICE Never turn off the power while the Initialize operation is being executed (that is, while the [REC], [PLAY], [+R] and [–L] lamps are flashing). NOTE If this instrument somehow becomes disabled or malfunctions, turn off the power then execute Initialization. CLP-525 Owner’s Manual 27 Appendix Troubleshooting Problem Possible Cause and Solution Power suddenly and unexpectedly turns off. This is normal and the Auto Power Off function may have been activated (page 12). If desired, disable the Auto Power Off function. The instrument does not turn on. Securely insert the adaptor plugs into the socket on this instrument and into a proper AC outlet (page 11). A click or pop is heard when the power is turned on or off. This is normal when electrical current is being applied to the instrument. Noise is heard from the speakers or headphones. The noise may be due to interference caused by the use of a mobile phone in close proximity to this instrument. Turn off the mobile phone, or move it further away from this instrument. Noise is heard from the instrument’s speakers or headphones when using the instrument with the application on iPhone/iPad. When you use the instrument along with the application on your iPhone/ iPad, we recommend that you set “Airplane Mode” to “ON” on your iPhone/ iPad in order to avoid noise caused by communication. The Master Volume is set too low. Set it to an appropriate level using the [MASTER VOLUME] knob (page 13). The overall volume is low, or no sound is heard. Make sure a pair of headphones is not connected to the headphones jack (page 12). Make sure that Local Control is On. For details, refer to the “MIDI Reference” (page 8). 28 Pedals do not function. The pedal cord may not be securely connected to the [TO PEDAL] jack. Be sure to insert the pedal cord all the way until the metal part of the cord plug disappears from view (page 30). The damper pedal does not function as expected. The damper pedal was pressed when the power was turned on. This is not a malfunction; release the pedal and press it again to reset the function. CLP-525 Owner’s Manual Keyboard Stand Assembly CAUTION • Assemble the unit on a hard and flat floor with ample space. • Be careful not to confuse parts, and be sure to install all parts in the correct orientation. Please assemble the unit in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Be sure to use only the included screws of the specified sizes. Do not use any other screws. Use of incorrect screws can cause damage or malfunction of the product. • Be sure to tighten all screws upon completing assembly of the unit. • To disassemble the unit, reverse the assembly sequence given below. 1. Attach (finger-tighten) C to D and E. 1-3 Have a Phillips-head (+) screwdriver of the appropriate size ready. Remove all parts from the package and make sure you have all of the items. 1-1 1-1 Untie and straighten out the bundled pedal cord. Don’t discard the vinyl tie. You will need it later in step 6. Foamed styrol pads Remove foamed styrol pads from the package, position them on the floor, then place A on top of them. Position the pads so that they will not hide the connectors on the bottom of A. 1-2 1-3 2. Align D and E with each end of C. Attach D and E to C by finger-tightening the long screws (6 x 20 mm). Attach B. 2-1 Bundled pedal cord inside 2-2 2-3 2-2 6 x 20 mm long screws x 4 Power cord x 1 2-1 4 x 12 mm thin screws x 2 AC power adaptor x 1 The power cord and adaptor may 4 x 20 mm tapping screws x 4 not be included, or may look 6 x 16 mm short screws x 6 Cord holders x 2 2-2 different from the illustration above, depending on your particular area. Please check with your Yamaha dealer. 4 × 10 mm thin screws x 2 2-2 Align the screw holes on the upper side of B with the bracket holes on D and E, then attach the upper corners of B to D and E by finger-tightening two thin screws (4 x 12 mm). While pushing the lower part of D and E from outside, secure the bottom ends of B using two tapping screws (4 x 20 mm). Headphone hanger x 1 CLP-525 Owner’s Manual 29 Keyboard Stand Assembly 2-3 2-4 3. Insert the other two tapping screws (4 x 20 mm) into the other two screw holes to secure B. 5. Secure A. 5-1 Securely tighten the screws on the top of B that were attached in Step 2-1. Secure C. Securely tighten the screws on C that were attached in Step 1-3. 5-2 5-1 3 4. 5-2 Mount A. Be sure to place your hands at least 15 cm away from either end of the main unit when positioning it. Align the screw holes. 6. Adjust the position of A so that the left and right ends of A will project beyond D and E equally when seen from the front. Secure A by tightening the short screws (6 x 16 mm) from the front. Connect the pedal cord and the AC power adaptor. 6-5 6-1 At least 15 cm 6-3 CAUTION • Be extra careful not to drop the main unit or let your fingers be pinched by it. • Do not hold the main unit in any position other than the position specified above. 30 CLP-525 Owner’s Manual 6-2 Keyboard Stand Assembly 6-1 Insert the pedal cord plug to the [TO PEDAL] jack from the rear. When connecting the pedal cord, insert the plug securely until the metal part disappears from view. 6-2 6-3 6-4 After completing the assembly, please check the following. • Are there any parts left over?  Review the assembly procedure and correct any errors. • Is this instrument clear of doors and other movable fixtures?  Move the instrument to an appropriate location. Attach the cord holders to the rear panel as shown, then clip the cord into the holders. Use a vinyl tie to take up any slack in the pedal cord. Connect one end of the power cord to the power adaptor. • Does this instrument make a rattling noise when you shake it?  Tighten all screws. • Does the pedal box rattle or give way when you step on the pedals?  Turn the adjuster so that it is set firmly against the floor. • Are the pedal cord plug and the adaptor plug inserted securely into the sockets?  Check the connection. • If the main unit creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly diagrams and retighten all screws. 6-5 7. CAUTION Insert the DC plug of the AC power adaptor into the DC IN jack. Set the adjuster. • When moving the instrument after assembly, always hold the bottom of the main unit. • Do not hold the key cover or top portion. Improper handling can result in damage to the instrument or personal injury. Do not hold here. Rotate the adjuster until it comes in firm contact with the floor surface. 8. Attach the headphone hanger. Hold here. Use two thin screws (4 x 10 mm) to attach the hanger as shown in the illustration. Transporting If you move to another location, you can transport the instrument along with other belongings. You can move the unit as it is (assembled), or you can disassemble the unit down to the condition it was in when you first took it out of the box. Transport the keyboard horizontally. Do not lean it up against a wall or stand it up on its side. Do not subject the instrument to excessive vibration or shock. When transporting the assembled instrument, make sure all screws are properly tightened and have not been loosened by moving the instrument. CLP-525 Owner’s Manual 31 Specifications Items CLP-525 Width 1350 mm (53-1/8") [1353 mm (53-1/4")] [For models with polished finish] Height Without Music Rest 845 mm (33-1/4") [848 mm (33-3/8")] [For models with polished finish] With Music Rest 999 mm (39-5/16") [1000 mm (39-3/8")] Depth Without Music Rest 414 mm (16-5/16") [415 mm (16-5/16")] [For models with polished finish] With Music Rest 414 mm (16-5/16") [415 mm (16-5/16")] Size/Weight Weight 43.0 kg (94 lbs., 13 oz) [45.0 kg (99 lbs., 3 oz)] [For models with polished finish] Keyboard Control Interface Pedal Cabinet Voices/ Tone Generation Effects/Functions Connectivity Sound System Power Supply Hard/Medium/Soft/Fixed Number of Pedals 3 Half Pedal Yes (Damper) Functions Sustain, Sostenuto, Soft English Sliding Music Rest Yes Piano Sound Yamaha CFIIIS Number of Polyphony (Max.) 256 Number of Voices 10 Reverb 4 types Smooth Release Yes Damper Resonance Yes Dual Yes Duo Yes Intelligent Acoustic Control (IAC) Yes Recording Metronome Storage GH3 (Graded Hammer 3) keyboard with synthetic ivory keytops Touch Response Key Cover Style Compatible Data Format Overall Controls 88 Type Panel Language Preset Recording/Playback (MIDI data only; audio not supported) Number of Keys Number of Preset Songs 10 Demo Songs, 50 Piano Preset Songs Number of Songs 1 Number of Tracks 2 Data Capacity (Max.) Approx. 100 KB/Song (Approx. 11,000 notes) Recording SMF (Format 0) Playback SMF (Format 0 & 1) Yes Tempo Range 5 – 280 Transpose -6 – 0 – +6 Tuning 414.8 – 440.0 – 466.8 Hz Internal Memory Total maximum size approx. 900 KB (User song: One song approx. 100 KB, Loading song data from a computer: Up to 10 songs) Headphones Yes (x 2) USB TO HOST Yes Amplifiers 20 W x 2 Speakers Oval (12 cm x 6 cm) x 2 Acoustic Optimizer Yes Power Consumption 13 W (when using the PA-300C) Auto Power Off Yes (Approx. 30 minutes) Accessories • • • • • Owner’s Manual Quick Operation Guide “50 Greats for the Piano” (Music Book) Online Member Product Registration AC power adaptor: PA-300C or an equivalent recommended by Yamaha* • Power cord* • Bench* * Included or optional depending on your locale Options (May not be available depending on your locale.) • USB MIDI Interface for iPhone/iPod touch/iPad: i-UX1 • Headphones: HPE-160 • AC power adaptor: PA-300C or an equivalent recommended by Yamaha * Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. 32 CLP-525 Owner’s Manual Index Numerics P 50 Preset Songs ........................................................23 Panel Controls and Terminals ................................ 9 Pedals ........................................................................ 14 Pitch .......................................................................... 20 Power ........................................................................ 11 Power indicator ....................................................... 11 Practice ..................................................................... 24 Preset Songs ............................................................. 23 A AC power adaptor .....................................................8 Accessories ..................................................................8 Auto Power Off ........................................................12 B Beat ............................................................................15 Q C Quick Operation Guide ............................................ 8 Quick Play ................................................................ 24 Computer-related Operations .................................8 D Damper Pedal ...........................................................14 Damper Resonance .................................................14 Delete .........................................................................26 Demo Song List ........................................................18 Demo Songs ..............................................................18 Dual mode ................................................................21 Duo ............................................................................22 H Half-pedal .................................................................14 Headphones ..............................................................12 Hz (Hertz) .................................................................20 I Initializing .................................................................27 Intelligent Acoustic Control (IAC) .......................13 K R Recording ................................................................. 25 Reverb ....................................................................... 19 Reverb Depth ........................................................... 19 Reverb Type ............................................................. 19 Reverb Type List ...................................................... 19 Right-hand Part ....................................................... 24 S Soft Pedal .................................................................. 14 Sostenuto Pedal ....................................................... 14 T Tempo ....................................................................... 15 Touch Sensitivity ..................................................... 16 Transpose ................................................................. 20 Tuning ...................................................................... 20 U Key Cover .................................................................10 USB TO HOST .......................................................... 9 User Song ................................................................. 25 L V Left-hand Part ..........................................................24 M Manuals .......................................................................8 Metronome ...............................................................15 MIDI Basics ................................................................8 MIDI Reference .........................................................8 Voice ......................................................................... 17 Voice List .................................................................. 17 Volume ...............................................................13, 15 O Octave ........................................................................21 Online Manuals (PDF) .............................................8 CLP-525 Owner’s Manual 33 MEMO The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the bottom of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. (bottom_en_01) Le numéro de modèle, le numéro de série, l'alimentation requise, etc., se trouvent sur ou près de la plaque signalétique du produit, située dans la partie inférieure de l'unité. Notez le numéro de série dans l'espace fourni ci-dessous et conservez ce manuel en tant que preuve permanente de votre achat afin de faciliter l'identification du produit en cas de vol. N° de modèle The name plate is located on the bottom of the unit. La plaque signalétique de ce produit se trouve dans le bas de l'unité. N° de série (bottom_fr_01) For CLP-525 and AC Power Adaptor Information for Users on Collection and Disposal of Old Equipment This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC. By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [For business users in the European Union] If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. (weee_eu_en_01) Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques. Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels. Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale et aux Directives 2002/96/EC. En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pourraient advenir lors d'un traitement inapproprié des déchets. Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez acheté les produits. [Pour les professionnels dans l'Union Européenne] Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre vendeur ou fournisseur pour plus d'informations. [Information sur le traitement dans d'autres pays en dehors de l'Union Européenne] Ce symbole est seulement valable dans l'Union Européenne. Si vous souhaitez vous débarrasser de déchets d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander la méthode de traitement appropriée. (weee_eu_fr_01) For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A. Tel: 714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México, S.A. de C.V. Av. Insurgentes Sur 1647 “Prisma Insurgentes”, Col. San Jose Insurgentes, Del. Benito Juarez, 03900, Mexico, D.F. Tel: 55-5804-0600 BRAZIL Yamaha Musical do Brasil Ltda. Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi, CEP 04534-013 São Paulo, SP. BRAZIL Tel: 011-3704-1377 ARGENTINA Yamaha Music Latin America, S.A., Sucursal Argentina Olga Cossettini 1553, Piso 4 Norte, Madero Este-C1107CEK Buenos Aires, Argentina Tel: 54-11-4119-7000 VENEZUELA NETHERLANDS/BELGIUM/ LUXEMBOURG Yamaha Music Europe Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, Netherlands Tel: 0347-358 040 FRANCE Yamaha Music Europe 7 rue Ambroise Croizat, Zone d'activites Pariest, 77183 Croissy-Beaubourg, France Tel: 01-64-61-4000 ITALY Yamaha Music Europe GmbH, Branch Italy Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 SPAIN/PORTUGAL Yamaha Music Europe GmbH Ibérica, Sucursal en España Ctra. de la Coruna km. 17,200, 28231 Las Rozas (Madrid), Spain Tel: +34-91-639-88-88 GREECE Philippos Nakas S.A. The Music House 147 Skiathou Street, 112-55 Athens, Greece Tel: 01-228 2160 SWEDEN Yamaha Music Europe GmbH Germany filial Scandinavia J. A. Wettergrensgata 1, Box 30053 S-400 43 Göteborg, Sweden Tel: +46 31 89 34 00 DENMARK Yamaha Music Europe GmbH, Tyskland – filial Denmark Generatorvej 6A, DK-2730 Herlev, Denmark Tel: 44 92 49 00 Yamaha Music Latin America, S.A., Sucursal Venezuela C.C. Manzanares Plaza P4 Ofic. 0401- Manzanares-Baruta Caracas Venezuela Tel: 58-212-943-1877 FINLAND PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES NORWAY Yamaha Music Latin America, S.A. Torre Banco General, Piso No.7, Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, República de Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM/IRELAND Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, U.K. Tel: 01908-366700 GERMANY Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 SWITZERLAND/LIECHTENSTEIN Yamaha Music Europe GmbH Branch Switzerland in Zürich Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: 044-387-8080 AUSTRIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 CZECH REPUBLIC/HUNGARY/ ROMANIA/SLOVAKIA/SLOVENIA Yamaha Music Europe GmbH Branch Austria (Central Eastern Europe Office) Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 POLAND/LITHUANIA/LATVIA/ ESTONIA Yamaha Music Europe GmbH Branch Poland Office ul. Wrotkowa 14 02-553 Warsaw, Poland Tel: 022-500-2925 BULGARIA Dinacord Bulgaria LTD. Bul.Iskarsko Schose 7 Targowski Zentar Ewropa 1528 Sofia, Bulgaria Tel: 02-978-20-25 MALTA Olimpus Music Ltd. The Emporium, Level 3, St. Louis Street Msida MSD06 Tel: 02133-2144 DMI7 Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. F-Musiikki Oy Kluuvikatu 6, P.O. Box 260, SF-00101 Helsinki, Finland Tel: 09 618511 Yamaha Music Europe GmbH Germany Norwegian Branch Grini Næringspark 1, N-1361 Østerås, Norway Tel: 67 16 78 00 ICELAND Skifan HF Skeifan 17 P.O. Box 8120, IS-128 Reykjavik, Iceland Tel: 525 5000 RUSSIA Yamaha Music (Russia) LLC. Room 37, bld. 7, Kievskaya street, Moscow, 121059, Russia Tel: 495 626 5005 OTHER EUROPEAN COUNTRIES Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 AFRICA SOUTH AFRICA Global Music Instruments Unit 4, 130 Boeing Road East Bedfordview 2008 Postnet Suite 130, Private Bag X10020 Edenvale 1610, South Africa Tel: 27-11-454-1131 OTHER AFRICAN COUNTRIES Yamaha Music Gulf FZE LOB 16-513, P.O.Box 17328, Jebel Ali, Dubai, United Arab Emirates Tel: +971-4-881-5868 MIDDLE EAST TURKEY/CYPRUS Yamaha Music Europe GmbH Merkezi Almanya Türkiye İstanbul Şubesi Maslak Meydan Sokak No:5 Spring Giz Plaza Bağımsız Böl. No:3, 34398 Şişli, İstanbul Tel: +90-212-999-8010 OTHER COUNTRIES Yamaha Music Gulf FZE LOB 16-513, P.O.Box 17328, Jebel Ali, Dubai, United Arab Emirates Tel: +971-4-881-5868 ASIA THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 HONG KONG Tom Lee Music Co., Ltd. 11/F., Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688 INDIA Yamaha Music India Pvt. Ltd. Spazedge building, Ground Floor, Tower A, Sector 47, Gurgaon- Sohna Road, Gurgaon, Haryana, India Tel: 0124-485-3300 INDONESIA PT. Yamaha Musik Indonesia (Distributor) Yamaha Music Center Bldg. Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 021-520-2577 KOREA Yamaha Music Korea Ltd. 8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong, Kangnam-Gu, Seoul, Korea Tel: 02-3467-3300 MALAYSIA Yamaha Music (Malaysia) Sdn., Bhd. No.8, Jalan Perbandaran, Kelana Jaya, 47301 Petaling Jaya, Selangor, Malaysia Tel: 03-78030900 PHILIPPINES Yupangco Music Corporation 339 Gil J. Puyat Avenue, P.O. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 SINGAPORE Yamaha Music (Asia) Private Limited Block 202 Hougang Street 21, #02-00, Singapore 530202, Singapore Tel: 65-6747-4374 TAIWAN Yamaha Music & Electronics Taiwan Co.,Ltd. 3F, No.6, Section 2 Nan-Jing East Road, Taipei, Taiwan R.O.C. Tel: 02-2511-8688 THAILAND Siam Music Yamaha Co., Ltd. 3, 4, 15 and 16th floor, Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: 02-215-2622 VIETNAM Yamaha Music Vietnam Company Limited 15th Floor, Nam A Bank Tower, 201-203 Cach Mang Thang Tam St., Ward 4, Dist.3, Ho Chi Minh City, Vietnam Tel: +84-8-3818-1122 OTHER ASIAN COUNTRIES Yamaha Corporation Market Development Section Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 NEW ZEALAND Music Works LTD P.O.BOX 6246 Wellesley, Auckland 4680, New Zealand Tel: 9-634-0099 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation Market Development Section Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 Yamaha Global Site http://www.yamaha.com/ Yamaha Downloads http://download.yamaha.com/ C.S.G., DMI Development Division © 2013 Yamaha Corporation 312MWAP*.*-01B0 Printed in Vietnam ZH76640 ZH76640